CATHODE RAY TOMES

World Series 2001

World Series Baseball (SEGA, 2001) · Manual · 45 pages · 17 sections · original scan

Page 1

1ST PRINTING MAY 01 ics os |

Upright Version

Owner’s Manual

SEGA ENTERPRISES, INC. USA MANUAL NO. 999-1288

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.

Indicates that mishandling the Indicates that mishandling the product product by disregarding this by disregarding this caution will cause

warning will cause a potentially a slight hazardous situation which can
WARNING! hazardous situation which can CAUTION! result in personal injury and or material result in death or serious injury. damage.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this display is attached to places where the Owner’s Manual and or Service Manual should be referred to.

© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.

© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.

O Besure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.

Page 4

© _ Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. ©. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. © _ When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.

  • Descriptions herein contained may be subject to improvement changes without notice. © The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

Page 5

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWIN

  • HANDLING PRECAUTIONS
  • SPECIFICATIONS ....
  • CONTENTS OF GAME 5-10
  • TEST MODE 11-19 A.SYSTEM MENU B.GAME TEST MODE a.INPUT TEST Switch input test is performed. b.GAME ASSIGNMENTS Various settings such as game difficulty, etc. can be set. c. VOLUME SETTING This page allows you to adjust the volume settings used for the ANALOG STICKS and BAT MECHA. d.BOOKKEEPING Allows for checking data such as operation time, game time, etc. e.BACKUP DATA CLEAR Clears the contents of BOOKKEEPING. . GAME BOARD . . SOFT KIT........ . COIN SELECTOR . . DESIGN RELATED PARTS . PARTS LIST (CONTROL PA
  • WIRE COLOR CODE TABLE..
  • WIRING DIAGRAM (CONTROL PANEL) CxeOIDUM

Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.

Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.

IMPORTANT

@ When using the cabinet that shares the coin chute between 1P and 2P (such as the NAOMI CABINET, BLAST CITY, etc.), change the setting of the COIN CHUTE TYPE item in the COIN

IMPORTANT ASSIGNMENTS screen, from INDIVIDUAL to COMMON. Using these cabinets with the setting of INDIVIDUAL disables to play from the 2P side. For more information about the COIN ASSIGNMENTS screen, see the NAOMI Service Manual. When having connected the power for the first time, open the SYSTEM MENU - GAME TEST MODE - INPUT TEST screen and test the input devices; thereby make sure that they can function normally. This game is available only with the NAOMI GD-ROM system. It is not available with other hardware.
Page 6
  • HANDLING PRECAUTIONS

off the power for the cabinet when installing or removing the IC Board.

WARNING! Extraneous matter such as dust on the IC Board can cause the IC Board

to generate heat and result in a fire due to short circuit, etc. Ensure the IC Board surfaces are always kept clean. Use NAOMI for the cabinets compatible with JVS. Using NAOMI for the cabinet other than those compatible with JVS can cause generation of heat and a fire. j\ To prevent electric shock or IC Board malfunctioning, be sure to turn

Be sure to connect the IC Board and connectors completely. Insufficient insertion can damage IC Board, etc. INPORTANT For the IC Board circuit inspection, only the use of Logic Tester is permitted. The use of ordinary testers is not permitted as these can damage the IC Board. Do not subject the IC Board to static electricity when installing the IC Board in the cabinet or when connecting wire harness connectors to the IC Board. When soldering buttons, etc. to the wire harnesses, be sure to remove the wire harnesses from the IC Board so as not to subject the IC Board to heat. Using NAOMI without the Shield Case can cause electric wave trouble. Be sure to use NAOMI together with the accessory Shield Case. The monitor frequency corresponding to NAOMI is 15kHz or 31kHz. NAOMI can not be used for the cabinet incorporating a monitor or projector not corresponding to 15kHz or 31kHz.

@ Concerning the display of JAMMA VIDEO STANDARD: JAMMA VIDEO STANDARD adopted by NAOMI is referred to as JVS. As against this Standard, the conventional JAMMA STANDARD which employs 56P Edge Connectors adopted by ST-V, etc. is displayed as Old JAMMA STANDARD. The specific Manual attached to each game sometimes displays JVS as JV STANDARD, New JAMMA STANDARD, or JAMMA 2 STANDARD against OLD JAMMA STANDARD as JAMMA STANDARD, JS, etc.

@ The contents herein described are subject to change without notice.

Page 7
  • SPECIFICATIONS

® MONITOR Monitor Position

Horizontal Synchronous Frequency HORIZONTAL 15/31 kHz

@ CONTROL PANEL @ NEW ASTRO CITY, NAOMI CABINET, NET CITY, BLAST CITY (PART NO. HOT-20011 or NOA-20010-01)

00H 00H FFH = FFH = \ AY \ \ FFI 00H f 1 IP 2Prey 00H (] \ @ssurt0n 29 @ O2eTT0N / 00H onfFH<-- 00H, @ oy FHS ANALOG BAT MECHA ANALOG BAT MECHA LEVER LEVER PLAYER 1 PLAYER 2

ANALOG LEVER: Move cursor (for throwing, batting); Specify base (for defense, base running) A BUTTON: Throw (for defense); Steal base (for batting); Advance to next base (for base running) Enter command (within command acceptance time) B BUTTON: Check runner (for throwing); Move between bases (for defense); Return to base (for running) Enter command (within command acceptance time) BAT MECHA: Swing START: Start game; Time out (for throwing, batting)

The analog input on the I/O board uses the following channels: CHO : 1P ANALOG LEVER VOLUME VERTICAL UP(FFH) DOWN(00H) CH1 : 1P ANALOG LEVER VOLUME HORIZONTAL LEFT(FFH) RIGHT(00H) CH2 : 1P BAT MECHA VOLUME — STANDARD POS.(00H) MAX(FFH) CH3 : (RESERVE) CH4 : 2P ANALOG LEVER VOLUME VERTICAL UP(FFH) DOWN(00H) CHS5 : 2P ANALOG LEVER VOLUME HORIZONTAL LEFT(FFH) RIGHT(00H) CH6 : 2P BAT MECHA VOLUME — STANDARD POS.(00H) MAX(FFH) CH7 : (RESERVE)

® Minimum DIMM Memory Capacity 256 MB

Page 8

Removing and Attaching the BAT MECHA

A

WARNING! If you need to remove the BAT MECHA as in the case of a failure, open the control panel base and remove the BAT MECHA through the following procedure. To reinstall the BAT MECHA, reverse the removing procedure, being certain that the BAT MECHA is faced in the correct direction. For instructions on opening the control panel base, refer to the Instruction Manual of the cabinet.

Remove the wiring connector (AMP 3P, white) located near the volume.

Remove the wiring connector (AMP 3P, white) located near the volume @ Remove the tamperproof screw clamping the bat center axis on the front side of

the control panel.

Tightening/loosening of the tamperproof screw should use the tamperproof screw M4 wrench (540-0006-01) that is included as an accessory for the NAOMI CABINET, NET CITY, and NEW ASTRO CITY cabinet.

|, The tamperproof screw M4 wrench is not included with the following cabinets: ” w Wersus CITY, New VERSUS CITY, and BLAST CITY.

If the wrench is not available, please order the following part numbers: + Wrench type (M4): — 540-0006-01

  • Screwdriver type (M4): 540-0018

Remove the four flange nuts clamping the BAT MECHA body on the back side of the control panel.

BAT MECHA Part number: 610-0409 Part name: ASSY BAT MECHA

The above figure does not show the wiring of the volume and its connector (AMP 3P, white).

Page 9
  • CONTENTS OF GAME

This is a sports action game where the Major League Baseball in the United States of America was taken as a subject matter. In this game, the following teams appear: 14 American and 16 National teams, and two all-star teams from the two leagues. The number of players appearing in the game is over 700. All of the 30 really existing ballparks also appear there. The game player or players operate their favorite teams to participate in the baseball game, aiming at the win. The following play modes are available: Player vs. CPU, Player vs. Player, and Game of Intrusion.

HOW TO PLAY THE GAME

First select your favorite from the 32 teams. Use the lever to designate the selected team, and use the A Button for determination. This applies also to all the subsequent operations. Next select the desired one from the 30 ballparks. Then select the starting pitcher. You can select the desired pitcher from the five candidates appearing on the screen. Finally select one of three levels: Easy, Standard, and Hard. The fielding strategy you use depends on the level you selected. LEGEND - HARD -: Hard. Both catching and throwing the ball are operated by the player. The speed of the pitched ball, i.e., pace, is the maximum. VETERAN - MEDIUM -: Standard. Both catching and throwing the ball are operated by the player. The pace is the standard. ROOKIE - EASY -: Easy. > ll the operations to catching the ball are made by the CPU. All the subsequent operations are made by the player. The pace is the minimum.

The game start. The shortest way to the win is to take advantage of the strong points of the individual baseball players to play the game. Apart from the score of the actual baseball game, game points may increase or decrease, depending on the contents of the baseball game. If the resulting number of game points is listed at an upper rank when the game is cleared, your name is included in the entry. In the Player vs. CPU or Player vs. Player mode, the game is cleared if the play continues until the entire baseball game ends, and if you have won, you see the ending. If the difference in score reaches the preset value during the progress of the game, the game is immediately treated as a called game, resulting in Game Over.

Page 10
  • The settings in GAME ASSIGNMENTS in the Test Mode control how the game

If this is ON, the extra part of the baseball game continues to

If this is OFF, the baseball game ends when the bottom of the ninth inning ends (even if the score is even, i.e., the game is ends:

EXTRA INNING: a maximum of 12th innings.

drawn). CALLED GAME: Can be set in the 5 to 10 range. When the difference in score reaches the setting, the baseball game ends (even if the bottom of that inning is not yet completed).

+ Ifthe game play begins at the other seat while a player is in progress at either 1P or 2P seat, you enter the Game of Intrusion Mode. For any play in the Game of Intrusion Mode, the starting inning varies with the GAME ASSIGNMENTS settings.

INNINGS: For | inning, the game begins at the top of the ninth inning. For 2 innings, the game begins at the top of the eighth inning. For 3 innings, the game begins at the top of the seventh inning. For all innings, the game begins at the top of the first inning.

In the Game of Intrusion Mode, the game may continue to up to the bottom of the ninth inning. The winner can subsequently continue the play in the Player vs. CPU Mode. Ifa draw results from a baseball game in the Game of Intrusion Mode, Game Over results for both of the players.

GAME SCREEN

Pitching & Batting Screen

Information in Game

Batter's (Batting) Team By operating the lever, select the direction of the Pitch Type Marker arrow to select the expected pitch type.

Pull the batting switch toward you and keep it there until the pitcher pitches the ball.

Third Base Window Game Points (Differs from the actual score of the baseball game.)

IP 123000080 RECORD 200378000 2P 8921000

Pitch Type Marker The baseball player and ball positions on the ground.

Pitcher's (Fielding) Team By operating the lever, select the pitch type by the direction of the Pitch Type Marker arrow.

Press the A Button to initiate the pitch. The pitching gauge appears next to the pitcher on the screen.

First Base Window

Page 11

Batter's (Batting) Team

By operating the lever, move the batting cursor to aim at the ball.

Release the batting switch timely to hit the ball.

Batter's (Batting) Team

If your expectation turns out right, the batting cursor is highlighted and the probability of hit increases. Pitching Gauge

1P 123000080 RECORD 200378000 ‘P 8921000

Strike Zone Batting Cursor

1P 123000080 RECORD 200378000

oe

The cursor shape changes depending on the expected pitch type. If your expectation turns out right, the ball will be hit more easily and to a further point, with the cursor color changed. 2P 8921000 Pitcher's (Fielding) Team

Select the course of the ball using the lever.

While observing the pitching gauge, press the A Button timely (best when MAX appears at the top of the game).

Pitcher's (Fielding) Team

Pressing the button timely improves all of the speed and control of the ball and the sharpness of breaking balls. If you press the button untimely (too early or late), all of the speed and control of the ball and the sharpness of breaking balls will be poor reversely.

Page 12

Fielding Screen

Landing Point \ Fielding Team

Using the lever, move a fielder to the expected landing point of the ball.

OUT

2nd BASE Lever Up: 2nd Base 3rd BASE ' Lever Left: 3rd Base Ist past” Lever Right: Ist Base

HOME BASE Lever Down: Home Base 1P 123000080 RECORD 200378000 2P By pressing the B Button, you can replace the field you want to move. 8921000

When approximating to the ball, the fielder automatically catches the ball.

For example, the ball is occasionally carried away by wind.

If you press the A Button timely, the fielder exhibits a super catch by fine play. If you selected ROOKIE- EASY- for the level at the start of the game, the above operations are unnecessary.

1P 123000080 RECORD 200378000 2P 8921000 Throw/Shift

Select the desired base using the lever.

Pressing the A Button causes the fielder to throw the ball to the base you selected.

Pressing the B Button causes the fielder to run toward the base you selected.

1P 123000080 RECORD 200378000 2P 8921000 Base running

Select the desired base using the lever.

Pressing the A Button causes the fielder to run toward the base you selected.

Pressing the B Button causes the fielder to return to the previous base.

While you hold the A and B Buttons together, the field stays there.

Page 13

© Pitch Type Marker

The pitch type marker shows the available pitch types.

FAST BALL FAST BALL Fy Fy

Ol: SLIDER SLIDERIOO8 HOlscREW ats, BALL SER, So

CURVE CURVE v SINKER

CHANGE-UP CHANGE-UP FORKBALL FORKBALL ETC. ETC. For right-hander For left-hander

Original ability of pitcher

© Batting Cursor

If you successfully expect the actual pitch type, the shape of the batting cursor changes.

If you expect and enter FAST BALL (or enter nothing):

If you successfully expect the actual pitch type, the shape of the batting cursor changes.

If you expect and enter CURVE If your entered expectation turns (or SINKER for left-hander): right, the cursor turns red.

Page 14

© NAMES AND ABBREVIATIONS OF THE TEAMS AND BALLPARK NAMES APPEARING IN THE GAME

The team names are listed alphabetically.

American League National League

  • Anaheim Angels/ANA 1. Arizona Diamondbacks/ARI :Edison International Field :BankOne Ballpark
  • Baltimore Orioles/BAL 2. Atlanta Braves/ATL :Oriole Park at Camden Yards :Turner Field
  • Boston Red Sox/BOS 3. Chicago Cubs/CHC :Fenway Park :Wrigley Field
  • Chicago White Sox/CHW 4. Cincinnati Reds/CIN :Comiskey Park :Cinergy Field
  • Cleveland Indians/CLE 5. Colorado Rockies/COL ‘Jacobs Field :Coors Field
  • Detroit Tigers/DET 6. Florida Marlins/FLA :Comerica Park :Pro Player Stadium
  • Kansas City Royals/KC 7. Houston Astros/HOU :Kauffman Stadium :Enron Field
  • Minnesota Twins/MIN 8. Los Angeles Dodgers/LA :Hubert H.Humphrey Metrodome :Dodger Stadium
  • New York Yankees/NYY 9. Milwaukee Brewers/MIL ‘Yankee Stadium :Miller Park
  • Oakland Athletics/OAK 0. Montreal Expos/MON :Network Associates Coliseum :Olympic Stadium
  • Seattle Mariners/SEA 1. New York Mets/NYM :SAFECO Field :Shea Stadium
  • Tampa Bay Devil Rays/TB 2. Philadelphia Phillies/PHI :Tropicana Field :Veterans Stadium
  • Texas Rangers/TEX 3. Pittsburgh Pirates/PIT :The Ballpark in Arlington :PNC Park
  • Toronto Blue Jays/TOR 4. St. Louis Cardinals/STL :SkyDome :Busch Stadium
  • San Diego Padres/SD :Qualcomm Park at Jack Murphy Stadium
  • San Francisco Giants/SF :Pacific Bell Park
Page 15
  • TEST MODE

A. SYSTEM MENU

ASSIGNMENTS, and GAME ASSIGNMENTS of GAME TEST MODE,

S When settings are changed in SYSTEM ASSIGNMENTS, COIN

be sure to exit from the test mode of SYSTEM MENU screen. The contents

IMPORTANT of setting changes are stored in the IC on the BOARD when exiting from

the Test Mode. If the power is turned off in the Test Mode (before exiting), the contents of setting changes are ineffective. In this case, the settings remain unchanged.

This test mode mainly allows the IC Board to be checked for accurate functioning, monitor color to be adjusted as well as COIN ASSIGNMENTS and GAME ASSIGNMENTS to be adjusted.

  • After turning power on, press the TEST Button to have the following SYSTEM MENU displayed.

SYSTEM MENU

RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS <~_} BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING

DIMM BOARD TEST GAME TEST MODE [XXXXXXXXX ]

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON In the SYSTEM ASSIGNMENTS, CABINET TYPE is set to 2 PLAYER(S), ‘MONITOR TYPE is set to HORIZONTAL, ‘und SERVICE TYPE is set to COMMON.

“CCOIN ASSIGNMENTS settings as follows: *COIN CHUTE TYPE: COMMON *COIN/CREDIT SETTING: You may set COIN/CREDIT SETTING and/or SEQUENCE Noptionally. +SEQUENCE SETTING of COIN ASSIGNMENTS functions +as follows: +SEQUENCE 1: Number of credits required for game start a (1-5) 4SEQUENCE 2: Number of credits required for CON- 7 TINUE(1~5) uSEQUENCE 3 ~ 8: NOT USED.

  • Press the SERVICE Button to move the arrow. Bring the arrow to the desired item and press the TEST Button.
  • Press the TEST Button in the GAME TEST MODE to display the GAME TEST MENU peculiar to this game. See the next page onward.
  • Upon finishing the test, bring the arrow to EXIT and press the TEST Button to return to the Game mode.

For detailed explanations as regards the SYSTEM TEST MODE, refer to GD-ROM SERVICE MANUAL (420-6620-01).

Page 16

B. GAME TEST MODE

By selecting "GAME TEST MODE" and pressing the TEST Button on the System Test Menu Screen, the Test Mode Menu Screen (Game Test Mode Menu Screen) appears, which is unique to this game.

GAME TEST MENU

INPUT TEST GAME ASSIGNMENTS VOLUME SETTING BOOKKEEPING BACKUP DATA CLEAR -> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

GAME TEST MENU Screen

+ Pressing the SERVICE Button moves the arrow (->) on the screen. By moving the arrow, select the item you want to run.

+ Pressing the TEST Button runs the currently selected item. You are brought to the screen for that item, and can change or adjust the settings.

+ With "EXIT" selected, pressing the TEST Button returns you to the System Test Menu Screen.

+ All the subsequent GAME TEST MODE operations can basically be made using the B and A Buttons instead of the SERVICE and TEST Buttons.

SERVICE Button - B Button TEST Button - A Button

Page 17

a. INPUT TEST

This test checks the input devices. Using this screen, check the input devices periodically. Pressing the TEST and SERVICE Buttons together returns you to the Game Test Menu Screen.

INPUT TEST

1P_START :OFF 2P_START :OFF 1P_ABUTTON:OFF 2P_ABUTTON:OFF 1P_BBUTTON:OFF 2P_BBUTTON:OFF TEST-SW :OFF SERVICE-SW:OFF

[e) [e)

1P_LEVER:(80,80) 2P_LEVER:(80,80) IP_BAT : 80 2P_BAT : 80

PRESS TEST AND SERVICE BUTTON TO EXIT

INPUT TEST Screen

Operate each of the input devices. If the indication at the right of the device label changes from OFF to ON, the device is normal. LEVER and BAT indicate the lever and batting switch volume control values, respectively. Check whether each of the values changes and the cursor moves smoothly according to the lever or batting switch operations you make.

+ Lever and batting switch settings LEVER: Check that, when you move the lever fully to the top, bottom, left, or right, the cursor, marked by a circle (A6) in the figure, moves securely from an end to another in the frame while the value below the frame is changing.

BAT: Check that, when you move the batting switch fully from an end to another in the movable range, the cursor, marked by horizontal bars in the figure, moves securely from the top (or bottom) to the bottom (or op) while the value below the frame is changing.

If the cursor does not move from an end to another, retry to set a proper value with VOLUME SETTING and then perform the recheck on this Test Screen.

Page 18

b. GAME ASSIGNMENTS

S Once you have made change to the settings, select and run EXIT and

exit the GAME TEST MODE. The new settings do not take effect until this mode is exited.

IMPORTANT

This screen lets you make change to the game difficulty and other settings.

Changing Procedure

® Press the SERVICE Button to move the arrow to the item to which you want to make change.

@ Pressing the TEST Button changes the indication located at the right of the currently selected item. Change it to the desired one.

@ Press the SERVICE Button to select EXIT, and press the TEST Button. This

returns you to the Game Test Menu Screen.

GAME ASSIGNMENTS

DIFFICULTY NORMAL INNINGS 2 INNINGS EXTRA INNING ON CALLED GAME 10 INITIAL TEAM 1P NYY 2P NYM -> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

GAME ASSIGNMENTS Screen

Page 19

*DIFFICULTY: _ Set the difficulty by changing the pitching speed of the pitcher or modifying the CPU's routine of thinking. Set one of the following five levels:

VERY EASY - EASY - NORMAL - HARD - VERY HARD Easier > Harder

+ INNINGS: Set the number of innings you can play with the start-enabled (or continuable) credits. When each setting has been made, an additional credit is required each time any inning in parentheses (A@) ends.

1 INNING setting: (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) 2 INNINGS setting: (1, 2) (3, 4) (5, 6) (7, 8, 9) (10, 11, 12) 3 INNINGS setting: (1, 2, 3) (4, 5, 6) (7, 8, 9) (10, 11, 12) ALL INNINGS setting: No additional credit is required even if you play the extra part of the baseball game to a maximum of 12th innings.

+ EXTRA INNING: Set whether the game may continue to extra innings. If this is OFF, the game ends even if the score is even after the end of the bottom of the ninth inning.

  • CALLED GAME: Set the difference in score that allows the game to be established as a called game. The value may be 5 to 10. When the difference in score reaches the setting, the game ends.

+ INITIAL TEAM: Set the team that is first selected on the Select Team Screen.

Page 20

c. VOLUME SETTING

@ Normal play is guaranteed only after all the input devices have been set up properly. Be sure to make the proper settings before you begin demonstration for

IMPORTANT the selling purpose.

Once you have made change to the settings, select and run EXIT WITH SAVE and exit the GAME TEST MODE. The new settings do not take effect until this mode is exited.

This screen lets you set the sensitivity of the input devices. f you are unsatisfied with the operability or have adjusted or replaced the volume control of an input device, make the settings on this screen.

VOLUME SETTING PLAYERI LEVER_H MAX(FFH) MIN(OOH) NOW(80H) LEVER-V MAX(FFH) MIN(00H) NOW(80H) BAT MAX(FFH) MIN(00H) NOW(00H)

PLAYER2 LEVER-H MAX(FFH) MIN(00H) NOW(80H) LEVER-V MAX(FFH) MIN(00H) NOW(80H) BAT MAX(FFH) MIN(00H) NOW(00H)

EXIT WITH SAVE -> EXIT WITHOUT SAVE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

VOLUME SETTING Screen

Page 21

Setting Procedure

Move the lever and batting switch fully in the movable range.

@ Release the lever and batting switch, and leave them unloaded.

Move Lever Horizontally (LEVER-H) Move the lever fully to the left or right, and then leave it unloaded.

Move Lever Vertically (LEVER-V) Move the lever fully to the top or bottom, and then leave it unloaded.

Batting Switch (BAT) Move the batting switch fully, and then leave it unloaded.

@Move the SERVICE Button to align the arrow with EXIT WITH SAVE, and press

the TEST Button. Save the settings, and return to the Game Test Menu Screen.

+ Ifyou press the TEST Button with the arrow aligned with EXIT WITHOUT SAVE, you return to the Game Test Menu Screen without making change to the settings.

+ After adjustment, be sure to use INPUT TEST to check that the values change properly according to the operations you make. If no improvements are observed even after the settings are retried, a component such as the lever or batting switch may have failed.

Page 22

d. BOOKKEEPING

This screen lists the data to be saved. Pressing the TEST Button returns you to the Game Test Menu Screen.

BOOKKEEPING

NUMBER OF GAMES 0 TOTAL PLAY TIME OD 00H 00M 00S AVERAGE PLAY TIME 00M 00S LONGEST PLAY TIME 00M 00S SHORTEST PLAY TIME 00M 00S

PRESS TEST BUTTON TO EXIT

BOOKKEEPING Screen

@ NUMBER OF GAMES: Total number of games played

@ TOTAL PLAY TIME: Play time

Page 23

e. BACKUP DATA CLEAR

BACKUP DATA CLEAR

YES (CLEAR ) -> NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

BACKUP DATA CLEAR Screen

This screen is used to initialize BOOKKEEPING and the High Score Ranking. To clear the data about the coins/credits, you have to run BACKUP DATA CLEAR in the SYSTEM TEST MODE. Clearing the data does not influence any game settings (except the data). When clearing, use the SERVICE Button to bring the arrow (->) to "YES (CLEAR)" and press the TEST Button. When the data has been cleared, "COMPLETED" will be displayed. Press the TEST Button to return to the Menu mode. Bring the arrow to "NO (CANCEL)" and press the TEST Button to return to the Menu mode without clearing the data.

Page 24
  • GAME BOARD

or malfunctioning. Static electricity discharge can damage electronic parts on the IC

CAUTION! Board. Before starting work by opening the Shield Case Lid, be sure to touch grounded metallic surfaces to discharge physically charged static electricity. When replacing the Game Board, refer to the CVT Manual and Instruction Manual. j\ Do not expose the Game Board so as to avoid causing an accident

PART NO. DESCRIPTION

@+ @840-0051D-01ASSY CASE NAO PCI DIMM BD USA.

840-0051D-02 ASSY CASE NAO PCI DIMM BD EXP 840-0051D-03 ASSY CASE NAO PCI DIMM BD KOR 840-0051D-04 ASSY CASE NAO PCI DIMM BD AUS

®840-0001A-01ASSY CASE NAOMI MAIN BD USA

840-0001A-02 ASSY CASE NAOMI MAIN BD EXP 840-0001A-03 ASSY CASE NAOMI MAIN BD KOR 840-0001A-04 ASSY CASE NAOMI MAIN BD AUS

@) 840-0001F ASSY CASE NAO DIMM BD COM

®610-0617GD-ROM DRIVE UNIT NAOMI

610-0617-01 GD-ROM DRIVE UNIT NAOMI VA2

Page 25

442-00067B (STICKER 840-0067B) lace Attached p!

PART NO. DESCRIPTION

® 840-0001F ASSY CASE NAO DIMM BD COM

a) KEY CHIP

O+® 840-0067B DIMM BD NAO MB2K2

Page 26
  • SOFT KIT

S Handling the GD-ROM Disk

@ Do not contaminate the disks with your

IMPORTANT fingerprints or dust particles. Contaminated disks may lower audio and video quality. @ When cleaning the disks, do not use volatile chemicals (benzine, thinner, etc.), cleaning sprays, and antistatic agents. Do not use cracked, warped, or damaged Use clean cloth to wipe disks. the disk gently and into Do not attach papers or seals onto the disks; 2 "dial direction. do not scratch the disks. Do not use the disks with a sign of peeled seals, tapes, etc. Observing these instructions, do not insert such a non-usable disk into the GD-ROM drive. Otherwise the inserted disk can not be ejected. When cleaning a heavily contaminated disk, use clean cloth that has been soaked in water and squeezed. Then remove moisture with dry cloth. When holding a disk, be careful not to contaminate it with your fingerprints.

How to Hold a Disk

With both hands: With one hand: Put your thumbs and forefingers of both _ Insert your forefinger into a hands on the disk's 4 circumference tips. _ central hole and at the same time put your thumb and middle finger on the disk's 2 circumference tips.

How to Handle the Key Chip @ The key chip is a precision device. Handle it carefully because it may be damaged by heat, shock, and static electricity. @ Use the key chip with the GD-ROM disk of the corresponding game that has been shipped together with the key chip.

Page 27

PART NO. DESCRIPTION

610-0624-0010 GD SOFT KIT MB2K2 ENG

GDS-0010 * NAOMI GDROM MB2K2

KEY CHIP

420-6621-0010E SERVICE MANUAL MB2K2 ENG

253-5507 DISK CASE WITH IC HOLDER

Page 28
  • COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

@ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and

IMPORTANT then squeezed dry. Never apply machine oil, etc. to the Coin Selector. After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the FIG. 1a Selector correctly functions.

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft. Remove stain from the rotary shaft and shaft receiving portions by wiping off with a soft cloth, etc. © After wiping off as per ® above, further apply a dry cloth, etc. to cause the coin selector to dry completely. Insert a coin COIN INSERTION TEST Rewer Butog Onc « pressed down and nce every month, when performing check if it is the Coin SW Test, simultaneously i check the following: Does the Coin Meter count satisfactorily? Does the coin drop into the Cashbox correctly? Is the coin rejected when inserted while keeping the Reject Button FIG. 11 ¢ pressed down?

Page 29

Nouswosaa FUNSOTONA TldadS % YOO WOLLOd == YxOLVGNVA WOO'D39 MM 099-968-008" TI HLIM S3ldLNA 2 6£909 I ‘OOVIIHO FYVOTIN'N LOLZ YOOG INIW Y3GNN/YIA0 NOILWYOdYOD SIINOYLDI14 L0-OL L2-S LGM YINGYV9-ST1IM

Page 30

Tom Happ Ph: 847-593-6161 ext. 107 tom.happ@happcontrols.com Fx: 847-956-2091 Happ Controls, 106 Garlisch Drive, Elk Grove, IL 60007 Visit our website http://www.happcontrols.com 42-0641-00 iL 42-0405-00 FOR §.25 COIN 42-0405-05 FOR $1.00 COIN o.. 0291-40 = 42-1044-00 $1.00 4 x .25 1 PLAY 42-0895-05 $1.00 PUSH TO AEJECT

42-7201-00 o- 42-0292-00

48-1000-00 ll J ‘ 42-0119-00

sissieqo —42-0288-00 (/¢~ 43 7. 42-0351-00 oie \

43-1002-00. 43-1003-00. 42-7355-00 $0.26 42-3078-00 $1.00 42-3113-00 42-7087-00 jononnon 42.0641-00 43-0136-00—>" —_ @a— 43-0021-00 42-8178-400

  • 42-8174-10 Guardian Hasp 30-2400-200
Page 31

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON WORLD SERIES 2001 UPRIGHT COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATOR(S):

FORWARD-MOST Mars 2000 series HOLE POSITION

**42-1155-00 MARS VALIDATOR $1, 2,5 300 CAP

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the cut-out plate. This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The part number is 40-6000-10EX. The Mars stacker can be obtained through an autherized Mars distibutor.

Note: Your game may have either Happ Controls Coin Door Assembly or the Wells Gardner Coin Door Assembly (not shown).

**Happ part number

Security Locking Bar/Bracket Set Part No.# 999-0966

Modified Cash Box (For use when DBA installed) Part No. # 999-1106

Plastic Cash Box - Full Size Part No. # 999-1177

Page 32
  • DESIGN RELATED PARTS

ITEM NO.

BWNe PART NO.

999-1216 999-1217 999-1218 999-1219 DESCRIPTION

MARQUEE WORLD SERIES BASEBALL DECAL INSTR. #1 UPPER BEZEL WS BASEBALL DECAL INSTR. #2 UPPER BEZEL WS BASEBALL DECAL CTRL PNL WS BASEBALL

Page 33
  • PARTS LIST (CONTROL PANEL) G) Top Assy (D-1/2)
Page 34

() Top assy

ITEM NO.

ANWRWNE NOT SHOWN PART NO.

999-1198 LOC. PURCHASE 999-1189 999-1187 NOA-1202 999-1196 999-1195 999-1190 999-0167 999-0169 999-1193 999-1192 999-1191 999-1188 999-1194 NOA-20010-01 (D-2/2)

DESCRIPTION

HEADER GLASS FLUORESCENT FIXTURE 24” 20 WATT BEZEL NAOMI COBALT BLUE MONITOR COVER ASSY SPEAKER BOX UPRIGHT LEFT - SILVER METALIC UPRIGHT RIGHT - SILVER METALIC SERVICE COMPARTMENT DOOR LEG LEVELER 1/2 - 13 CASTER 160-2 WOOD SHELF CONTROL SUB ASSY CONTROL SHELF - COBALT BLUE WOOD SHELF HOUSING - COBALT BLUE SHELF HINGE - COBALT BLUE CHAIN CTRL PNL STAY (2 PER) ASSY CTRL PNL

Page 35

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 36

@) ASSY CTRL PNL 2A4B2S MB2K2 ENG (NOA-20010-01) (D-2/2)

ITEM NO. PART NO.

HOT-2023 NOA-2025-01

610-6723-4B02 610-6723-4B01 610-0409 999-1290 999-1086 999-1289 280-5009-01 280-5275-SR10

050-U00400 060-F00400 060-S00400 050-H00400 DESCRIPTION

CTRL PNL BASE 2A4B2S CTRL PNL PLATE 2A4B2S ENG

ASSY ANALOG JOY 4B PINK ASSY ANALOG JOY 4B GREEN ASSY BAT MECHA PUSHBUTTON RND YELLOW W/MICRO (2 PER) PUSHBUTTON RND GREEN W/MICRO (2 PER) PUSHBUTTON RND PINK W/MICRO (2 PER) CORD CLAMP 21 CORD CLAMP SR10

U NUT M4 FLT WSHR M4 SPR WSHR M4 HEX NUT M4

Page 37

G) swuNIT

ITEMNO. PART NO. DESCRIPTION

LOC. PURCHASE COIN METER 6 VOLTS 2 LOC. PURCHASE PUSH BUTTON SW 3 LOC. PURCHASE 5 K POTENTIOMETER & VOLUME KNOB

Page 38

@ ELEC Assy

ITEM NO.

TSC rwraannsawne PART NO.

840-0051D-01 600-7009-2500 837-13551-92 600-7141-0250 400-5397-01 LOC. PURCHASE LOC. PURCHASE 838-13616 998-0148 XKT-0833 600-7247-500 DESCRIPTION

ASSY CASE NAO DIMM BD US ASSY RGB CA D-SUB 15P 2500MM VO CONTROL BD FOR JVS USB CABLE 250 CM (2 per) POWER SUPPLY FUSE BLOCK LINE FILTER AUDIO POWER AMP 2 CH TRANSFORMER MCI 4-06-8036 GD-ROM DRIVE KIT CABLE SCSI ST-L TYPE 2 500CM

Page 39

(3) FAN UNIT

ITEMNO. PART NO. DESCRIPTION

1 LOC. PURCHASE 4” FAN 120 V LOC. PURCHASE ROCKER SW 15 AMP 3 999-1204 PLATE LINE CORD

Page 40
  • WIRE COLOR CODE TABLE

THE WIRE COLOR CODE is as follow:

MOoOaADP PINK

SKY BLUE

BROWN

PURPLE

LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

CamaIME WHE RED

BLUE

YELLOW

GREEN

WHITE

ORANGE

BLACK

GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1:
Note 2: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51 oe WHITE / RED

aN I

RED WHITE

The character following the wire color code indicates the size of the wire.

U: AWGI16

K: AWGI18

L: AWG20

None: AWG22

Page 41
!CE 5 1p staer sw1ssanz 61 gunaBAAN 3l
:J‘nnalSANA
]2HoD.in
‘idsoz tf sinaab AAA
|tH3
| 21 A BUrTON(SW 1) 2g ——2wiTeW-)4 VOL
\(PE Hees sorte aa E\
:ao'
jHI618-6723-4B02

EAs an | ASSY ANALOG JOY 4B. PINK

:wees600-1154-001'
!at a3 A,j, 51

. ete

]CP 5 7p stant sypg‘SSTa
:mA™”WHITE (U-P)
|ie610-0409
'etfs PA BUTTON (SH 1) 25ASST BAT MECHA

' Hepa ee survon sw pas ELL

}aHne nee

| i

;HA 5a GNDaran
iEreTTT¥ VOL
iYELLOWIU-2)eae Nesna 3112I AAA, 51

os ¢

!|oso0an
j|Sina yy [akeaL AA. SL
''YELLOW (U-P) WHITE (U-P)Fa vo.
I\|
!poteI616-6723-4881
|Bee; ASSY ANALOG JOY 4B GREEN
:3Sa - a -H- —

aut i

R 541 oe 31BAA, 5
|BHcottaa

‘ SST Brau reuuon3) wHew=m

51K::.
:we600-7154-003518 8409
:'ASSY BAT MECHA

FE I

|ofp43 (105)i.2 ee epee
:basuo-6227-09EARTH TERVINAL

| WITE(U-P)

NOA-20010-01 ASSY CTRL PNL 2A4B25S B2K2 ENG Pe ra ee De J

ASSY ANALOG JOY 4B PINKSTART SWSTART SWASSY ANALOG JOY 48 GREEN

| U

: \ iA BUTTON (SW 1) ASSY BAT MACHA

B BUTTON (SH 2) \ B BUTTON (SW a)\ ASSY BAT MECHA A BUTTON (SH 1) 2P SIDE

=

[_{8 | phicBtxBxxRyFo=
[tieer aFa/GEGIA seca coaponation—__HUSeMMAG ney aae wer 8 came7 HS
LEoonPiCoat/ASSY CTRL PNL 2A4B2S5 MB2K2 ENG
TRATTN—pieritianGLA ULeaTonwaa | Mie, eae] e/2e- aaaa— zn]

T T T T

ABCDEFG
Page 42

cy u e F

A8a0££8
ACIZ0VON/OFF SWranerowen
50/60HzFUSE (SA)120V AC 17V 3A(2)
L__ BOKBOKBOKTT BLACK120VWHITE
EauNOISES ayy1rayaasuetaupto ¢ OO
Nose) |sa JSS S02waite'S—etrowt 3]RCH BLACK
ov | |ia ORANGE | 4Rea WHITE

'H4P AUDIO R RCA RED)

)REGU FOR JVS VA1 GRY

© Tok, scavi0a, tava, | § She 8» TO Sted

a_—————REDIU-P)

© ® Fou coy Ep SRE) |

aLMONITOR 27"asxxle} xleleG spk UC) [2 Setanta
wraa 8ssses $59émer)
120 15z=>=|paketo 888
88&Js“yhog fee
woviac’ <12deedx} xyx] xxx} 6 «(Ds 8888
[aftedgssfsiess}lS) SIS)x SS] SSS]Og SESES.
_|SSeSaese Sil asSal Sealfe RR aa Se
(FAN77ciaesia) Elamistaoisalale
{2hweesOSS SS)SES) SSSZS) slap =
\i20y5MESEMESGFe Sk)ORE RGRFL

{ a

J)

gH SS ste See f

LS ESeERS ERPRESES ~3EIE401 OWGRY-RE(Red)
—3ne.GRY-RELBK)
FrESSPK L.Zl
840-0051D-01g*antew

ASSY CASE NAO PCI DIMM BD SPK R. : ras)

  • _Siaitaiadd _/ lle

aadaag da added babbsbooddoooodsoodes boson y camenenen RENRARS 2 PoTTL EL ORS iter etter ttt] 38 age de fa sen usa 837-13551-92 VO CONTROL BD FOR JVS 30 430 50 USB-A 38 38 oo 502] cone so 7§50

Diy}—Teste| gl a8
71+ 7aSERVICE,

50 | fs : | Hy SARTO) jh B0x2_ | 30

80 | 804—s 3 88
- 307g} 30.7an
wea"610-0630-0010

—____BK ‘SPK

‘sageBil weGD-ROM DRIVE

WORLD SERIES BASEBALL

Ege eee — ft ee ape Pee———“==SEA Z|SEGA SEGA conrovar onlsat ok Shuto” OP
peeseeEE weo—oaoa eh | |fs _| ‘(WORLD SERIES BASEBALL
ALTERATIONeres eekgn——vopuassry01/12— 01 | a1712—@1| a1712~ a1| O1712— etae—

T 1

Page 43

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 44

VISIT OUR WEBSITE!

© SegaService.com

Por erraal G) hity://www.seuservice.com/

Search criteria:

SERVICE

  • Dari's Office *" What's New
  • Game Manuals *" Bultetins

Sega Enterprises Inc., USA Semwice Department phone 415.701.6580 fax 415.701.6594 { ‘ 11 ! UstaffllDarl's off [technical serice][customer senvice|{corporate info|[plugins][Non-framed page]

A total of EMew 1 people have accessed this page since June Sth.

Ifyou have any questions or comments about this Home Page please E-Mail to

darl davidson@seu sega. com OR dave. cantrelle@seu sega. com

Sega Enterprise Inc., USA. All rights reserved

You will need the following items to view this page in its entirety

Page 45

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax