CATHODE RAY TOMES

Airline Pilots Std Type

Airline Pilots (World, Rev B) (Sega, 1999) · Manual · 97 pages · 99 sections · original scan

Page 1

STD TYPE

OWNER’S MANUAL

haem eon j

==—_

SEGA ENTERPRISES, INC. USA

MANUAL NO. 4200-6479-01

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONS . PRECAUTIONS TO BE HEEDED FOR OPERATION . NAME OF PARTS . ACCESSORIES . ASSEMBLY AND INSTALLATION . PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE . CONTENTS OF GAME . EXPLANATION OF TEST AND DATA DISPLAY 7-1 SWITCH UNIT AND COIN METER 7-2. SYSTEM TEST MODE A CR.T. TEST B COIN ASSIGNMENTS 7-3 GAME TEST MODE A INPUT TEST B OUTPUT TEST C SOUND TEST D CR.T. TEST E GAME ASSIGNMENTS F VOLUME SETTING G BOOKKEEPING H BACKUP DATA CLEAR

  • CONTROL MECHA 8-1 REMOVING THE CONTROL MECHANISM 8-2. ADJUSTING THE VOLUME 8-3 REPLACING THE VOLUME 8-4 GREASING 8-5 REPLACING THE SWITCH LEVER
  • LEVER UNIT 9-1 ADJUSTING THE VOLUME 9-2. REPLACING THE VOLUME 9-3 GREASING
  • PEDAL UNIT 10-1 ADJUSTING THE VOLUME 10-2 REPLACING THE VOLUME 10-3 GREASING
  • COIN SELECTOR
  • MONITOR 12-1 CAUTIONS/WARNINGS FOR HANDLING 12-2 CAUTIONS TO BE HEEDED WHEN CLEANING 12-3 ADJUSTMENT METHOD
  • REPLACING THE FLUORESCENT LAMP.
  • PERIODIC INSPECTION TABLE
  • TROUBLESHOOTING
  • GAME BOARD 16-1 LOCATING THE GAME BOARD 16-3 COMPOSITION OF THE GAME BOARD
  • DESIGN RELATED PARTS
  • PARTS LIST
  • WIRING DIAGRAMS NAWRWNE
Page 4

SPECIFICATIONS

Installation space: 37.2 in.(W) x 64.0 in.(D)

Height: 73.6 in.

Weight: Approx. 617.3 lbs.

Power maximum current: 2.3 Amp AC 120V 60 Hz

MONITOR: 29” COLOR MONITOR

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to AIRLINE PILOTS STD TYPE, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 415-701-6580 Fax 415-701-6594 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 5

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in arisk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 6

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below:

  • Places subject to rain/water leakage, or condensation due to humidity;
  • In close proximity to a potential wet area;
  • Locations receiving direct sunlight;
  • Places close to heating units or hot air; ¢In the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
  • Places subject to any type of violent impact;
  • Dusty places.

INSTALLATION PRECAUTIONS

  • Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.
  • Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.
  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). ¢ For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

5K92

AMUSEMENT MACHINE

Page 7

1 .PRECAUTIONS TO BE HEEDED FOR OPERATION

In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION

WARNING!

A

CAUTION! @ In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can move and cause an accident.

Ensure that al} of the Adjusters are im contact with the floor.

Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. @ To avoid electric shock, check to see if door & cover parts are closed.

@ To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:

Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others and result in injury or trouble.

Page 8

PRECAUTIONS TO BE HEEDED DURING OPERATION

CAUTION!
CAUTION! To avoid injury and accidents, those who fall under the following catagories are not allowed to play the game:
  • Intoxicated persons
  • Those who have high blood pressure or heart problems.
  • Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
  • Persons susceptible to motion sickness.
  • Persons whose acts runs counter to the products warning displays.
  • Instruct those who wear high-heeled shoes to refrain from playing the game by explaining that playing the game with highheeled shoes is very dangerous and likely to cause a potentially hazardous situation.

@ To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in openings of the product or small openings in or around doors.

To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason. Although this product has the accident preventive covering attached to potentially hazardous places where hand and fingers could be caught, small children are unable to perceive hazards. Use care so that small children do not come close to the product when in play. Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage and/or falling down, resulting in injury due to fragments and falling down.

Page 9

2 .NAME OF PARTS POP_PANEL,

29 INCH MONITOR

LEVER SWITCH

CONTROL PANEL

OVERVIEW

AC UNIT

REAR VIEW

GAME SPECIFICATIONS WIDTH in. LENGTH in. HEIGHT in. WEIGHT lbs.

All measurements are and rounded UP

DURING SHIPPING 42” x 60” x 65” 669 LBS.

WHEN ASSEMBLED 37.25” x 64” Xx 73.715” 619 LBS.

Page 10

. ACCESSORIES

DESCRIPTION OWNERS MANUAL Part No. Qty.) 420-6479-01 (1)

Note

Figures Wf Part No. kes no description, the Number has not been regptered of cam mot be registered, Such 2 pat may act ‘be obtainable even if the customer desines tp purchase it. ‘Therefore. ensure that the part is in safekeeping with you.

AC Cable (Power Cord) 600-6729 (1) for TAIWAN 600-6618 (1) for OTHERS 600-4695 (1) for USA Used for installation. see [3] of Section 6.

SWITCH LEVER (GRAY! SOB-SOLL-G (1) Spare. see Section 1. Me SO-YG06-) (1) MB $40-0000-01 (1)

SWITCH LEVERRED) 808-5911-R (1) Spare. see Section 10.

Page 11

APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE

CAUTION FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2 HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD 2, OCEAN HUNTER, STAR WARS TRILOGY, ZOMBIE REVENGE, CRAZY TAXI, ARILINE PILOTS

MINE VER SeHlP MODEL 3 / NAOMI GAME

BOARDS OUTSIDE OF CAGE!!

h THE SHIPMENT METHOD DESCRIBED BELOW ONLY

CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM

( NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS

WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

WARNING!
Page 12
  • ASSEMBLING AND INSTALLATION

-Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the

CAUTION! machine, or malfunctioning to occur. -When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage. -Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards.

When carrying out the assembly work, follow the procedure in the following 5-item sequence:

1 | ASSY OF BILLBOARD

2 | SECURING IN PLACE (ADJUSTER ADJUSTMENT)

3 | POWER SUPPLY

4 | ASSEMBLING CHECK

Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.

ASSY OF BILLBOARD

Due to its large size, it is very difficult for one person alone to install the billboard, Make sure 2 or more persons are available to perform this work. Attempting to

WARNING! perform the installation alone can cause an accident.
Page 13

(0) Take out the 2 screws, and

remove the Plate Holder & Billboard Plate.

TRUSS SCREW (2). chrome.

@ From the rear of the Billboard,

remove the 2 Bolt Lids and the Connector Lid by taking out 2 screws from each

TRUSS SCREW{6 in total). chrome. M4x8

BILLBOARD HOOK Loosen the 2 Bolts.

(6) Loosen the 2 Bolts securing

the Billboard Hook.

Page 14

Hexagon Bolt (2), black, M8 X 20, w/spring washer, @® Mount the Billboard by hanging flat washer used. on the Billboard Hook, secure the Billboard with 2 Bolts through the square holes of Bolt Lids previously removed, and connect the Connector.

©) Install the 2 Bolt Lids and

Connector Lid.

Be sure to perform work by 2 persons.

© Insert the Billboard Holder in

place so as to fit the bolt positions, and fasten the bolts to secure the Billboard.

BILLBOARD HOLDER APC-0012

@ Install the Billboard Plate by \

using the procedure opposite ®

above POP_PANEL

Apply the oblique line portion of the POP PANEL to the upper rear part of the Billboard. At this time, ensure that the POP does not disappear.

Page 15

2 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the floor surface. Unless the Adjusters come into contact with the floor surface, the br sl Cabinet can move of itself, causing an accident.

This machine has 4 each of casters and adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

@ Move the machine to the installation position,

making sure to provide adequate space for the player to get on and off.

Q Cause all of the leg levelers to make contact

with the floor. By using a wrench, make adjustments in the height of the leg adjusters to ensure that the machine's position is kept level.

© After making adjustments, fasten the leg

adjuster nut upward and secure the height of the leg adjuster.

Permanantly tightening the hex bolts should not be completed until the leg levelers are adjusted properly.

CAUTION!
Page 16

3 | Power supPLy

@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. @ Ensure that the wiring position is not in the customer's passage way

WARNING! or the wiring has protective covering.

Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that power switch is off

MAIN SW

qd) Turning the AC unit’s main switch on will cause the machine

to start the power check and network check automatically.

Q) In the Power On check, the steering wheel turns left and right,

and then returns to the centering position and stops. In this check, the values of the VR inside the control panel are corrected.

B) Until this check is finished, and the steering wheel stops, do

not touch the steering wheel or play the game.

If you do, the steering reaction during the game (reaction at the time of course-out or crash) can not be obtained correctly. In the case of an abnormal reaction during the game, turn power on again from the beginning and complete the power on check. To the Power Supply Socket outlet

Page 17

ASSEMBLING CHECK

The TEST MENU allows for each part of the cabinet to be checked, the Monitor to be adjusted, and the coin and game related various functions to be performed.

In the TEST MODE, ascertain that the assembly has been made correctly and that the IC BOARD is satisfactory. In the test mode, perform the following test:

  • MEMORY TEST

RAM TEST

Ic29 GOOD IC35 GOOD IC16 GOOD IC18 GOOD IC20 GOOD IC22 GOOD Ico9 GOOD IC10 GOOD IC11 GOOD IC12 GOOD

PRESS TEST BUTTON TO EXIT

NO. Ic22 Ic1 Ic2 IC3 Ic4 ICS IC6 IC7 IC8 Ic Ic10 Ic11 ROM BOARD TEST [AIRLINE PILOTS IN XXXX]

TYPE 32M 64M 64M 64M 64M 64M 64M 64M 64M 64M 64M 64M RESULT

GOOD GOOD GOOD GOOD GOOD GOOD GOOD GOOD GOOD GOOD GOOD BYTE XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX WORD XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX

PRESS TEST BUTTON TO EXIT Selecting the RAM TEST and ROM TEST on the test mode menu screen causes the onboard memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

Page 18
  • CR.T. TEST

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be tory, color deviation, etc., may occur due to the effects of geomagnetism, the location of the building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the projector by refering to Section 7. displayed. Although the monitor adjustments have been made at the time of shipment from the

In the C.R.T. test of SYSTEM TEST mode, adjust color and screen size.

In the C.R.T. test of GAME TEST mode, adjust monitor brightness.

SYSTEM TEST mode

CRALTEST 172 CRI TEST 22 1 32

RED

GREEN

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE a

GAME TEST mode

CRITEST

TEST BUTTON TO EXIT

Page 19
  • INPUT TEST

INPUT TEST

LANDING GEAR SWITCH UP. FLAP SWITCH UP. VIEW CHANGE BUTTON OFF START BUTTON OFF SERVICE OFF TEST OFF CONTROL WHEEL (AILERON) ABH CONTROL WHEEL (ELEVATOR) ABH RUDDER PEDAL ABH THRUST LEVER L ABH THRUST LEVER R ABH

PRESS TEST AND SERVICE BUTTON TO EXIT

  • OUTPUT TEST

OUTPUT TEST

START BUTTON LAMP OFF LANDING GEAR UP LAMP OFF LANDING GEAR DOWN LAMP OFF FLAP UP LAMP OFF FLAP DOWN LAMP OFF VIEW CHANGE BUTTON LAMP, OFF

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS

TEST BUTTON

  • SOUND TEST

SOUND TEST

No. 0

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON TO EXIT Selecting the INPUT TEST on the game test mode menu screen carses the screen (on which each switch and VR. are tested) to be displayed. Press each switch. If the display beside each switch indicates “ON,” the switch and wiring connections are satisfactory.

Select OUTPUT TEST from the menu in the game test mode to cause the screen (on which each lamp is tested) to appear. Ensure that each lamp lights up satisfactorily.

In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD and wiring connections are tested, to be displayed. Be sure to check if the sound is satisfactorily emitted from each speaker and that the sound volume is appropriate.

Perform the above inspections also at the time of monthly inspection.

Page 20

5 . PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

@ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug inserted can damage the power cord and cause a fire or electric shock. When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury. When lifting the machine, do not push the cabinet from the left/right direction. Doing so can cause the cabinet to fall down, resulting in personal injury and or parts damage.

WARNING! |] @

AN

CAUTION!

Do not push the cabinet from the left/right direction.

If the ceiling height is insufficient, first remove the Billboard and then move the machine.

Have casters make contact with the floor.

Page 21
  • CONTENTS OF GAME

The following explanations apply in the event the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occured. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.

From GAME START up to the end of SELECT.

display or coin meter as number of coins inserted

FLAP UP LAMP (GREEN)

SEGA LOGO TITLE

4 Returns to the beginning

FLAP DOWN LAMP (RED)

CONTROL WHEEL

START BUTTON [e) GAME MODE 7

Insert a credit worth a number of coins. Up to 9 credits can be counted at a time. Coins inserted after counting 9 credits are neither counted as credits nor returned. However, those coins inserted after counting 9 credits are included in the data

LANDING GEAR UP_LAMP_ (GREEN)

LANDING GEAR SW

LANDING GEAR

iC; DOWN LAMP (RED)

Page 22

Press the START button to start.

When the GAME MODE select screen appears, select TRAINING mode or FLIGHT mode.

-Incline the CONTROL WHEEL left or right to select and press the START button to confirm the selection (hereafter, this method applies to any selection).

<In the case TRAINING MODE is selected:>

¢When the CONTROL SYSTEM select screen appears, select AUTO CONTROL. or FULL CONTROL.

In the AUTO CONTROL, only the CONTROL WHEEL and the RUDDER. PEDAL are operated by the player. The FLAP SW, LANDING GEAR SW, and THRUST LEVER are automatically controlled.

eIn the AUTO CONTROL, Control Switches need not be set. The TRAINING MODE game starts immediately.

In the FULL CONTROL, the TRAINING mode game starts after setting Control Switches in accordance with the on-screen instruction.

In the FULL CONTROL, all Contollers are operated by the player.

Page 23

<In the case FLIGHT MODE is selected:>

-The FLIGHT COURSE select mode appears on the screen. Select one from among BEGINNER, INTERMEDIATE, and EXPERT.

-The specific flight course of BEGINNER, INTERMEDIATE, and EXPERT corresponds to flight in the daytime, evening, and nighttime respectively.

-When the CONTROL SYSTEM select screen appears, select the CONTROL SYSTEM in the similar manner as in the TRAINING MODE

@HOW TO PLAY IN THE TRAINING MODE

This mode has 5 Training items, i.c., taking-off, turning, landing, evading engine trouble, and bad weather. The qualifying score is predetermined for each training item. If the player is disqualified, CONTINUE? appears on. the screen. *CONTINUE? appears on the screen also when nearing the end of flight time limit, deviating from the course and crashing. *When CONTINUE, the game starts from the beginning of that particular training. ¢When all of the training items are cleared, the total score will be displayed and the game is finished.

@HOW TO PLAY IN FLIGHT MODE

Take off from the airport and freely fly over Tokyo within the time limit. Passing near the Time Marker floating in the air increases the time limi *When nearing the time limit, select FLIGHT to continue flight for the remaining time or landing. *Select FLIGHT to continue up to the end of the time limit. When time is up, CONTINUE? appears on the screen. If CONTINUEA, flight can be continued again. When the LANDING MODE is selected, the on-screen scene changes to the LANDING course. If the landing is successful, the game is finished. Failing to make a landing results in a

Page 24

7 .EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

CAUTIONS TO BE HEEDED WHEN USING THE TEST MODE: In the case where plural machines are linked for communication play, if even one seat enters Gror) the test mode, all of the linked seats will enter the test mode. Therefore, if any one of the linked machines is in play, use care so as not to use the test mode. The contents of the setting changes made will not be effective unless the test mode is

IMPORTANT! finished in the test mode. When the setting is changed, be sure to “EXIT” in the menu mode. Do not press the TEST BUTTON during network check at the time of turning the power on or exiting from the test mode. If anyone of the linked machines uses the test mode during network check, all other Seats will continue network checking. Cause all of the Seats to reenter the test mode and then have all of the Seats exit from the test mode simultaneously.

TABLE EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

When the machine is installed, perform the following: INSTALLATION | 1. Check to see that each setting is as per the standard settings at the |SERVICE MANUAL OF MACHINE _ |time of shipment.

  • In the INPUT TEST mode, check each SW and VR. TA
  • In the OUTPUT TEST mode, check each of lamps. 733
  • In the MEMORY TEST mode, check ICs on the IC Board. 441

Choose MEMORY TEST in the MENU mode to allow the SERVICE MANUAL MEMORY MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked. 441

PERIODIC Periodically perform the following:

SERVICING 1. MEMORY TEST ; 441

  • Ascertain each setting.
  • In the INPUT TEST mode, test the CONTROL device TRA
  • In the OUTPUT TEST mode, check each of lamps. 733
CONTROL1. In the INPUT TEST mode, check each SW and VR.TA
SYSTEM2. Adjust or replace each SW and VR.8, 9, 10
  • If the problem can not be solved yet, check the CONTROL’s moves]
MONITORIn the MONITOR ADJUSTMENT mode, check to see if theR3

MONITOR adjustment is appropriately made.

IC BOARD1. MEMORY TEST441
  • In the SOUND TEST mode, check the sound related ROMs. 7x
DATA CHECKCheck such data as game play time and histogram to adjust theTE

difficulty level, etc 7-3

Page 25

7-1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ [If the COIN METER and the game board are electrically disconnected,

IMPORTANT! game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows:

SWITCH UNIT

DEMAGNETIZER SWITCH

SERVICE BUTTON TEST BUTTON

SWITCH UNIT

SPEAKER VOLUME (VOLUME) Controls the speaker volume for the right/left speakers. SERVICE BUTTON (SERVICE SW) Gives credits without registering on the coin meter. TEST BUTTON (TEST SW) For the handling of the TEST BUTTON, refer to the section on test mode. DEMAGNETIZER SWITCH (DEMAGNETIZER SW) Eliminates the on-screen color unevenness due to magnetization of CRT. First use this SW before performing the monitor’s color adjustment.

COIN METER

Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox. COIN METER

COIN METER,

Page 26

7-2 SYSTEM TEST MODE

mode is finished from EXIT in the MENU mode. If the power is turned off before the

TEST mode is finished, the contents of the setting changes do not take effect. eExecuting “BACKUP DATA CLEAR” in the SYSTEM TEST MODE does not clear the

S eThe contents of settings changed in the TEST mode are stored when the TEST

IMPORTANT!

BOOKKEEPING data in the GAME TEST MODE.

eEntering the TEST mode clears fractional numbers of coins less than one credit and BONUS ADDER data.

The SYSTEM TEST mode mainly allows checks of the IC Board for accurate functioning , monitor adjustment, as well as CRT TEST and COIN ASSIGNMENTS, etc. The following assignments, however, should be designated for this product.

@ CABINET TYPE : 1 PLAYER (S) @ MONITOR TYPE : HORIZONTAL

@ COIN CHUTE TYPE : COMMON

TEST ITEM SELECT

SYSTEM MENU

RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS

BOOK KEEPING

BACKUP DATA CLEAR CLOCK SETTING

ROM BOARD TEST

GAME TEST MODE

[XX XXXXXX XXX]

EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

® After turning the power on, press the TEST button to display the test item menu shown above.

@ Press the SERVICE button to move the arrow to the desired item and press the TEST button.

  • When finished, bring the arrow to EXIT and press the TEST button to return to the Game mode.
Page 27

[AJ C.R.T. TEST

  • RGB COLOR ADJUSTMENT SCREEN In this screen, monitor color can be checked.

aa aca Each of red, green, and blue is the darkest at the leftmost end, and becomes brighter towards the right-hand end in 31 gradiations. Monitor brightness is satisfactory if the white color bar is black at the left end and if it is white at the right end. fm | Press the TEST button to proceed to the next screen. GREEN RED

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE

  • MONITOR SIZE ADJUSTMENT SCREEN In this screen, monitor size can be checked.

CRA TEST 22 Adjust the crosshatch frame line so that the checkered pattern does not extend beyond the screen. Press the TEST button to return to the menu mode.

PRESS TEST BUTTON TO EXIT

Page 28

B] COIN ASSIGNMENTS

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

Gror) Setting changes cannot be stored unless the TEST BUTTON is pressed

while the arrow is on EXIT.

IMPORTANT!

® Press the SERVICE BUTTON to move the arrow to the desired item.

@ Change the desired item setting by using the TEST BUTTON.

(©) To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

COIN ASSIGNMENTS,

COIN CHUTE TYPE COMMON COIN/ CREDIT SETTING #1 COIN CHUTE #1 1 COIN 1 CREDIT

COIN CHUTE #2 1 COIN 1 CREDIT

MANUAL SETTING SEQUENCE SETTING -> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

(COMMON SETTING)

(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL) Set to COMMON. (A) (B)

(Cc) (D)

Up to 2 Coin Chutes (#1 and #2) can be used and also, (B) COIN/CREDIT SETTING ratio can be set seperately for #1 and #2.

(B) COIN/CREDIT SETTING (#1 ~ #27) Sets the credit increase increment per coin insertion. There are 27 settings from #1 to #27, expressed inOO credit(s) as against OOcoins inserted. #27 refers to FREE PLAY.

Page 29

(C) MANUAL SETTING

The Credit’s incremental increase settings as against a coin insertion are shown in further details than in (B) above (refer to Table 2). Also, note that when this MANUAL SETTING is performed, (B) COIN CREDIT setting becomes ineffective.

MANUAL SETTING

COIN ASSIGNMENTS, MANUAL SETTING

COIN TO CREDIT 1 (D) BONUS ADDER NO BONUS ADDER (E) COIN CHUTE #1 MULTIPLIER (F) 1 COIN COUNT AS 1 COIN CON 123456789 CREDIT 123456789

COIN CHUTE #2 MULTIPLIER (F) 1 COIN COUNT AS 1 COIN CON 123456789 CREDIT 123456789

SEQUENCE SETTING (G)

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

(D) COIN TO CREDIT Determines COIN/CREDIT setting.

(E) BONUS ADDER

This sets how many coins should be inserted to obtain one SERVICE COIN.

(F) COIN CHUTE (#1/#2) MULTIPLIER

This sets how many tokens one coin represents.

Page 30

Table 1: COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

SETTING FUNCTION OF CHUTE#1

SETTING #11 COIN1 CREDIT
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #51 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT
SETTING #131 COIN1 CREDIT
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN1 CREDITS

SETTING #27 FREE PLAY

Page 31

Table 2: MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT. 2 COINS 1 CREDIT. 3 COINS 1 CREDIT 4 COINS 1 CREDIT. 5 COINS 1 CREDIT. 6 COINS 1 CREDIT. 7COINS 1 CREDIT 8 COINS 1 CREDIT. 9 COINS 1 CREDIT

BONUS ADDER NO BONUS ADDER 2_ COINS GIVE 1 EXTRA COIN 3 COINS GIVE 1 EXTRA COIN 4 COINS GIVE 1 EXTRA COIN 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE | EXTRA COIN 7 COINS GIVE 1 EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

COIN CHUTE (#1/#2) MULTIPLIER 1_ COIN COUNTS AS_1 COIN 1_ COIN COUNTS AS_2 COINS 1 COIN COUNTS AS _3 COINS 1 COIN COUNTS AS_4 COINS 1 COIN COUNTS AS_5 COINS 1 COIN COUNTS AS_6 COINS 1_ COIN COUNTS AS_7 COINS 1 COIN COUNTS AS_ 8 COINS 1 9 COINS COIN COUNTS AS

Page 32

(G) SEQUENCE SETTING

Number of credits required for starting a game, etc. can be set. Each sequence can be set between 1 ~ 5 credit(s).

COIN ASSIGNMENTS SEQUENCE SETTING

SEQUENCE 1 2 CREDIT(S) SEQUENCE 2 1 CREDIT(S) SEQUENCE 3 1 CREDIT(S) SEQUENCE 4 1 CREDIT(S) SEQUENCE 5 1 CREDIT(S) SEQUENCE 6 1 CREDIT(S) SEQUENCE 7 1 CREDIT(S) SEQUENCE 8 1 CREDIT(S) EXIT [XXXXX XXXXX XXXXX XXXXX] DESCRIPTION OF SEQUENCE 1 CREDIT TO START 2 CREDIT TO CONTI NUE 3 NO USE 4 NO USE 5 NO USE 6 NOUSE 7 NO USE 8 NO USE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

SEQUENCE |: Number of credits required for game to start. SEQUENCE 2: Number of credits required for CONTINUE. SEQUENCE 3 ~ 8: NOT USED.

Page 33

7-3 GAME TEST MODE

MENU MODE

SYSTEM MENU

RAM TEST JVS TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING

ROM BOARD TEST

-> GAME TEST MODE [XX XXXXXX XX X]

EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON AIRLINE PILOTS TEST MENU

INPUT TEST OUTPUT TEST SOUND TEST C.R.T. TEST GAME ASSIGNMENTS VOLUME SETTING BOOKKEEP ING BACKUP DATA CLEAR -> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

SYSTEM TEST MODE MENU GAME TEST MODE MENU

Press the TEST button to display the SYSTEM TEST MODE MENU.

By pressing the SERVICE button, move the arrow (->) to select the GAME TEST MODE.

Press the TEST button to enter GAME TEST MODE. The screen displays the GAME TEST MODE

MENU.

By pressing the SERVICE button, move the arrow (->) to select the desired item. Press the TEST button to

execute the selected item.

Select EXIT and press the TEST button to exit from the GAME TEST MODE and return to the SYSTEM

TEST MODE MENU. Further, select EXIT and press the TEST button to finish SYSTEM TEST MODE

and return to the normal mode.

Page 34

A. INPUT TEST

Select INPUT TEST to have the screen shown below appear and to observe the status of each switch

and the value of each V.R. on the Control Panel. In this mode, Periodically check the status of each switch and V.R.

INPUT TEST

LANDING GEAR SWITCH FLAP SWITCH VIEW CHANGE BUTTON START BUTTON SERVICE TEST CONTROL WHEEL (AILERON) CONTROL WHEEL (ELEVATOR) RUDDER PEDAL THRUST LEVER L THRUST LEVER R uP uP OFF OFF OFF OFF ABH ABH ABH ABH ABH

PRESS TEST AND SERVICE BUTTON TO EXIT

B. OUTPUT TEST By pressing each switch, if the display on the right-hand side of the name of each switch changes to ON from OFF, the SW and the wiring connections are satisfactory. UP and DOWN. are displayed for LANDING GEAR SWITCH and FLAP SWITCH.

Operate CONTROL WHEEL, THRUST LEVER, etc. to check Volume value display variation.

To check CHUTE 1 & CHUTE 2 coin switches, open the COIN CHUTE DOOR and insert a coin(s) in the slot.

Simultaneously pressing the TEST BUTTON and the SERVICE BUTTON returns to the test menu.

Select OUTPUT TEST to cause the following screen to appear, and allows the status of each lamp to be checked. In this mode, periodically check the lamp status.

OUTPUT TEST

START BUTTON LAMP LANDING GEAR UP LAMP LANDING GEAR DOWN LAMP. FLAP UP LAMP. FLAP DOWN LAMP VIEW CHANGE BUTTON LAMP.

-> EXIT

AND PRESS TEST BUTTON OFF OFF OFF OFF OFF OFF

SELECT WITH SERVICE BUTTON Select the item with the SERVICE button and press the TEST button to alternate the display to and from ON and OFF. Outputting corresponds to the ON/OFF alternation.

When exiting from OUTPUT TEST with ON display, all of ON displays change to OFF.

Bring the arrow to EXIT and press the TEST BUTTON to. return to the menu mode.

Page 35

C. SOUND TEST

This test mode allows each sound used in the game to be checked.

‘SOUND TEST

@ Press the SERVICE button to increase the number m0 sequentially, emitting the next sound to be tested.

@ Press the TEST button to return to the TEST MENU.

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

D. C.R.T. TEST

Selecting C.R.T. test causes the monitor to display the following and allows the 3 screens (displayed simultaneously) to adjust brightness balance.

CRT. TEST

PRESS TEST BUTTON TO EXIT

Page 36

E. GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and allows game setting changes (game difficulty, etc.) to be made. After setting changes, be sure to exit from the TEST mode; the settings are not renewed until the TEST mode is exited.

SETTING CHANGE PROCEDURE

@ Press the SERVICE BUTTON to move the “->” to the desired item. @ Change to the desired setting by using the TEST BUTTON. © To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

GAME ASSIGNMENTS

GAME DIFFICULTY (TRAINING) NORMAL,

GAME DIFFICULTY (FLIGHT) NORMAL,

-> EXIT

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

F. VOLUME SETTING @ GAME DIFFICULTY (TRAINING) Sets the game difficulty for the TRAINING Mode. Game difficulty can be set from among the 5 categories, i.e., VERY EASY, MEDIUM EASY, NORMAL, MEDIUM HARD, and VERY HARD. Specifically, this varies the qualifying points in the TRAINING Mode.

GAME DIFFICULTY (FLIGHT) Sets the difficulty for the FLIGHT Mode. Game difficulty can be set from among the 5 categories, i.e., VERY EASY, MEDIUM EASY, NORMAL, MEDIUM HARD, and VERY HARD. Specifically, this varies the initial time for each course in the FLIGHT Mode.

When VOLUME SETTING is selected, the following appears on the screen and each Control Unit’s Volume can be set.

If the operability is unsatisfactory, or when adjusting or replacing the Volume, set the Volume in this mode.

VOLUME SETTING

MIN MAX

CONTROL WHEEL (AILERON)50H80H

(20H) (OF)

CONTROL WHEEL (ELEVATOR)50H80H

(20H) (DFM)

RUDDER PEDALSOH80H

(20H) (OF)

THRUST LEVER LSOH80H

(20H) (DF)

THRUST LEVER RSOH80H

(20H) (OFM)

EXITWITH SAVE --> EXIT WITHOUT SAVE

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT METHOD OF VOLUME SETTING

To perform Volume setting, move all Volumes from the minimum value to the maximum value

and select “EXIT WITH SAVE” and the status of

the CONTROL WHEEL and RUDDER PEDAL

are returned to the horizontal (neutral) position. If “EXIT WITHOUT SAVE?” is selected, the

setting is cancelled. The values in parentheses have already been saved.

Page 37

G. BOOKKEEPING

Choosing BOOKKEEPING in the MENU mode displays the data of the present operating status on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2. Pressing the TEST BUTTON while the second page is displayed returns the screen to the MENU mode.

BOOK KEEPING PAGEI/2

TOTAL TIME PLAY TIME AVERAGE PLAY TIME LONGEST PLAY TIME SHORTEST PLAY TIME

sesss

22222 g2222 BRRRB

PRESS TEST BUTTON TO CONTINUE

BOOKKEEPING PAGE 2/2

TIME HISTOGRAM

omoos ~ om29s 0 om30s ~ oMs9s 0 1Mo0S ~ 1M29S 0 1M30S ~ 1MS9S 0 2Mo0s ~ 2M29S 0 2M30S ~ 2MS9S 0 3Mo0S ~ 3M29S 0 3M30S ~ 3M5S9S 0 4moos ~ 4M29s 0 4M30S ~ 4Ms9s 0 SMoOS ~ SM29S 0 SM30S ~ SMS9S 0 6Moos ~ 6M29S 0 6M30S ~ 6MS9S 0 7MoOS ~ 7M29S 0 7M30S ~ 7MS9S 0 gmoos ~ 8M29S 0 8M30S ~ 8MS9S 0 gmoos ~ 9M295 0 9M30S ~ 9MS9S 0 OVER 10Mo00S 0

PRESS TEST BUTTON TO EXIT

H. BACKUP DATA CLEAR

BACKUP DATA CLEAR

YES (CLEAR) -> NO (CANCEL)

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT @ TOTAL TIME: Refers to TOTAL TIME energized except for the time used for the TEST Mode.

@ PLAY TIME: Refers to the game play time.

@ In Page 2/2, Histogram of Number of Play as against Play Time is displayed. For setting the DIFFICULTY, refer to this histogram.

e By-playtime play frequency bookkeeping is displayed in increments of 30 seconds from OMOOS to 9MS59S. Playtime in excess of 10 minutes is displayed all in the category of OVER 10MO0S.

This allows the contents of BOOKKEEPING and Player Ranking data to be cleared.

@ When clearing, use the SERVICE BUTTON to bring the arrow to “YES (CLEAR)” and press the TEST BUTTON.

@ When the data has been cleared, “COMPLETED” will be displayed, and it will automatically return to the BACKUP DATA CLEAR menu. Bring the arrow to “NO” and press the TEST BUTTON to return the screen to MENU mode.

@ Note that despite the “clear” execution, the settingsof the GAME ASSIGNMENTS, COIN ASSIGNMENTS, and BOARD SETTINGS do not change. Be very careful, however, because the remaining credits will be deleted

Page 38
  • CONTROL MECHA
WARNING! @ Be sure to turn power off before performing work, and avoid touching undesignated places. Failure to do so can result in electric shock and short circuit accidents. @ Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. @ When performing work, be sure to use 2 or more persons. One person alone performing work can cause accidents and parts damage.

In the test mode, if the CONTROL HANDLE’s VR variations are not within the allowable range, then a VR installation position adjustment or VR replacement is needed. Also, be sure to apply grease to the VR gear portion once every 3 months.

8 - | REMOVING THE CONTROL MECHANISM

® Turn the power switch off. @ Remove the 3 Hexagon Socket Bolts from the lower part of the Control Panel. ® Remove the 4 Tamperproof Screws from both sides of the control panel’s front ®@ Remove the 3 Tamperproof Screws from the underside of the control panel. © Carefully draw out the Control Mechanism in a mnner so as not to damage wiring and connectors inside the control panel..

Perform work by 2 or more persons. HEXAGON SOCKET BOLT(3). black M820, spring washer used.

CONTROL MECHANISM

CONTROL PANEL

TAMPERPROOF SCREW(3), black M8 X 20, flat & spring washers used.

WRX 30

Page 39

8 - 2 ADJUSTING THE VOLUME

WARNING!

©

)

(6) @ Never touch places other than those specified. Touching unspecified places can cause electric shock and/or short circuit. @ After the replacement or adjustment of the VR, be sure to set the variable value of the VR in the test mode’s Volume Setting.

The Volume Brackets can be

moved by loosening 2 screws from each Bracket. CONTROL MECHANISM CONTROL

WHEEL

=m CABINET side side

\

Move the Volume Brackets to VOLUME (STROKE)

220-5484 disengage the Adjust Gear mesh, . TATA n ENTER REFERENCE HOLE and move the Volume Shaft so that

the cut portion of the Volume Shaft faces opposite the Center Reference Hole of the Adjust Gear. e©o

VOLUME (ROLL)

VOLUME BRACKET

SCREW(2), black

M4X10,w/flat & spring washers.

SCREW(2). black

M4 X10, w/flat & spring washers.

Engage Gears and fasten the 2 screws.

Carefully move the CONTROL WHEEL left/right & forward/backward, and check to ensure that the Volume range is not exceeded

Upon completion of adjustment, be sure to perform Volume Setting in the TEST mode.

8-3 REPLACING THE VOLUME

® Disconnect the wiring connector. @ Take out the 2 screws which secure the volume Bracket and remove the Volume Bracket. @ Take out the 2 screws to remove the Volume Gear and replace the Volume. @ After replacing the Volume, follow the steps in 8-2 to adjust the Volume.

Page 40

8 - 4 GREASING

@ Be sure to turn the power off first, before performing work, and avoid touching unspecified places. Failure to do so can cause electric shock and/or short circuit.

WARNING!

@ Be sure to use the designated grease. Using undesignated grease can cause parts| damage

IMPORTANT! @ Do not apply greasing to undesignated places. Doing so can cause malfunctioning . or quality deterioration of parts.

Apply greasing to the following portions every 3 months. For Spray Grease, use NOK GLUBER L60 or GREASE MATE (Part No. 090-0066). For greasing the backside of the Centering Mechanism, take out the 4 Hexagon Socket Bolts and remove the Centering Base.

4 CENTERING BASE

HEXAGON SOCKET BOLT (4) / WaX10. flat © spring washers used.

/ om MESH PORTION

SLIDING PORTION(4 places)

BACKSIDE OF CENTERING MECHANISM

Page 41

8-5 REPLACING THE SWITCH LEVER

@ Before starting to work, ensure that the Power SW is OFF. Failure to observe this

can cause electric shock/short circuit.

WARNING! | @ Use care so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards.

(0) Take out the 4 screws and careful so as not to damage pe

remove the Switch Plate. Be

wiring.

TAMPERPROOF SCREW(4). black M4 X16

@ Remove and replace the Switch Lever.

SWITCH LEVER 509-591] G/R

Page 42
  • LEVER UNIT

@ In order to prevent electric shock and short circuit, be sure to turn off the power before performing work on the interior parts of the product.

WARNING! || @ Be careful not to damage wiring. Damaged wiring can cause electric shock or short circuit. @ Do not touch places other than those specified. Touching unspecified places can cause an electric shock or short circuit.

If the value movements of the Lever are Irregular, adjust or replace the Volume in the following procedure.

9-1 ADJUSTING THE VOLUME

® Remove the 4 screws to loosen the Lever Cover. Take out the 2 screws

and remove the Shift Cover Lower.

TRUSS SCREW (4), chrome Ma x6

@ The Volume Brackets can be moved by loosening the 2 screws securing TRUSS SCREW(2), black SHIFT COVER LOWER each. M4 X16,

©) By moving the Volume Bracket,

disengage ADJUST GEAR mesh. Move the Volume Shaft in the

manner so that the cut portion of the ADJUST GEAR Volume Shaft faces opposite the center of the ADJUST GEAR.

® Mesh gears and fasten the 2 screws.

© Carefully move the Lever forward & backward, and check to ensure

that the Volume range is not

exceeded.

© After making adjustments, be sure to perform Volume setting in the VOLUME BRACKET Lo \ | TEST mode. \y_SCREW(2) M4 X10

Page 43

9-2 REPLACING THE VOLUME

WARNING! Be sure to turn the power off first, before performing work, and avoid touching unspecified places. Failure to do so can cause electric shock and/or short circuit.

® Remove the Volume Gear from the Volume to replace the Volume.

@ After replacing the Volume, make adjustments as per 11-1 ADJUSTING THE VOLUME.

9-3 GREASING

WARNING!
IMPORTANT! Be sure to turn the power off first, before performing work, and avoid touching unspecified places. Failure to do so can cause electric shock and/or short circuit.

@ Be sure to use the designated grease. Using undesignated grease can cause part damage @ Do not apply greasing to undesignated places. Doing so can cause malfunctioning or quality deterioration of parts.

Apply greasing to the following portions once every three (3) months. For Spray Grease, use NOK GLUBER L60 or GREASE MATE (Part No. 090-0066).

GEAR MESH PORTION

Page 44
  • PEDAL UNIT

@ In order to prevent electric shock and short circuit, be sure to turn off the power before performing work on the interior parts of the product.

WARNING!|{ @ Be careful not to damage wiring. Damaged wiring can cause electric shock or short circuit. @ Do not touch places other than those specified. Touching unspecified places can cause an electric shock or short circuit.

In the TEST mode, if the value movements of the CONTROL WHEEL are irregular, adjust or replace the Volume in accordance with the following procedure: PEDAL MECHANISM COVER

10 - 1 ADJUSTING THE VOLUME

® Take out the 4 screws and remove the Pedal Mechanism Cover.

a TRUSS SCREW(4), black

  • WXs

@Loosen the 2 screws securing each Volume ADJUST GEAR VOLUME

Bracket and move the Volume Brackets.

VOLUME BRACKET

(6) Move the Volume Bracket to disengage

gear mesh. Move the Volume Shaft in the

manner so that the cut portion of the Volume Shaft faces opposite the center of the ADJUST GEAR.

® Engage the gears and fasten the 2 screws.

© Carefully move the Pedal forward & backward and check to ensure that the SCREW (2) Volume range is not exceeded. M4X<10.9/flat & spring washers

© Upon completion of adjustment, be sure to perform Volume setting in the TEST mode.

Page 45

10 - 2 REPLACING THE VOLUME

Be sure to turn the power off first, before performing work, and avoid touching unspecified places. Failure to do so can cause electric shock and/or short circuit.

WARNING!

® Remove the Volume Gear from the Volume to replace the Volume.

@ After replacing the Volume, make adjustments as per 12-1 ADJUSTING THE VOLUME.

10 - 3 GREASING

Be sure to turn the power off first, before performing work, and avoid touching unspecified places. Failure to do so can cause electric shock and/or short circuit.

WARNING!

@ Be sure to use the designated grease. Using undesignated grease can cause part: damage PORTANT! @ Do not apply greasing to undesignated places. Doing so can cause malfunctioning . or quality deterioration of parts.

Apply greasing to the following portions once every three (3) months. For Spray Grease, use NOK GLUBER L60 or GREASE MATE (Part No. 090-0066).

“>~_GEAR MESH PORTION

Page 46

11 .COIN SELECTOR

HANDLING THE COIN JAM

to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). Remove and cleen smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

e)

IMPORTANT! ©

@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selecting, Insert a regular coin in the normal working status and ensure that the Selector correctly functions.

COIN INSERTION TEST Once a month, when performing the COIN SW TEST, simultaneously check the following:

O Does the Coin Meter count satisfactorily? O Does the coin drop into the Cashbox correctly?

O Is the coin rejected when inserted while keeping

the REJECT BUTTON is pressed down? If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check

FIG. lla

FIG.11b

Insert a coin while keeping the Reject Button pressed down and check if itis rejected.

COIN METER

FIG. llc

Page 47

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON AIRLINE PILOTS STD TYPE COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 Mars 2000 series (FORWARD-MOST POSITION)

HOLE POSITION#2 Mars 2000 series DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 DSIO1*

*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls authorized distributors. The part number is 91-4000-01. The Mars stacker can be obtained through an autherized Mars distibutor.

Page 48

[L 10 AN LJSINT ERO LTS| a UVER/ UNDER LWU

laoinivielrinia tirlolnia Lu;‘ane)2

ENTRY COIN DOOR 1850 HOWARD ST., ELK GROVE EL 60007 (847) 228-1810 I 4

fi ae + WARS SERIES 2000 UPSTACKER ADAPTABLE fens, Sy a

PART #DESCRIPTIONcost. | PART #DESCRIPTIONcostPART #DESCRIPTIONcost
1 GOK S10 ATEPOR18.50P16) UGH RECT FLAP WOUOG, LACK2.70)28) 2-000 12 0 REait
ISON S-7 18 42%(2.00| 1M) SI-HLR-O{ INTRVABIECT SOTTO feah-110-04.57 OC ATER80
2) AITO PLASTIC CASETad]8) SLATER40/29) -102-OL ARR LOCO ORB&
3) M4840 LOSI, 22002750 | 19) SI-L121-00 8 BETTO SPRTNC|30) 2-0-0 OOK Bak10
4) 90-4C02-10-HINE SREY|M) MANOLP HEE BSES|SL) -t0t0-00 9/4" SoOTAStRRa
5) 90-02-10 CAND SCREHM) U-LSL-L6 HUTTON BURL acauth
8) 9-101F-10- SOR BRR NILONBf2) M-102-16 URC BRL AC2th
7) 90-120-42. A-40 RD HOTB|B) M225 127 KOT CTL ASSOLE2.6
8) 9-1200-0 HEVNKoB|) Stab AIGNTTRCL ASSOLE5.0
9) S616 TRUE30.00)U4) t-Li4G-tb MRISHTCE Backil
10) SL-E-40 CLAP6SIAL UL UGNSEITCE TITE5.40
11) S1-0640-00 UBL D Cal Love5BSIAL 10HIEOSEECE RD5.40
2) 9-00-16 LACE ATT IRS40| 2B) S-1225-00 HICRSTITON PLASTIC COMERa5
10) 94-O804-16 2 RATE OPEETOoR16.60)25) 2-10-04 CIN INLET LAP sToR1.0
WH) 91-108 LOOT BREET4326) BR-LO0-02L COIN IALAT (OTR STOR1.80
15) SLIMA-407_RISLATE ASSRABLY5.0027) S100 OLD WY auc1.50

JAN. 1998 FORM 92-1003-05

Page 49
  • MONITOR 12- 1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS

When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector (plug) before starting work. Proceeding the work without following this instruction can cause electric shock of malfunctioning.

CAUTION! Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA shall not be liable for any malfunctioning and accident caused by said conversion.

Primary side and secondary side The monitor’s circuit which is divided into the Primary side and secondary side, is electrically isolated. Do not touch the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock, and this is very dangerous. SECONDARY SIDE When making monitor adjustments, use a non- (Chassis, CRT) conductive driver and make adjustment without touching any other part other than the Adjustment PRIMARY V.R. and Knob. Also, be sure not to cause a short- SIDE circuit to the Primary side and the Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous.

High tension Voltage Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor, turn the power off so as not to cause malfunctioning or fire hazard.

E CAP ANODE LEAD ‘Approx. 29 kV

DEMAGNETIZER COIL

SECONDARY SIDE j FBT. Approx. (Chassis, sheet metal work, CRT, ete.) Disconnect or unplug 29 kV

Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavely charged as time elapses, generating high tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are disassembled, what’s charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.

Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversly affect the human body. Installation and removal Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work’s sharp edges, etc. and avoid damaging the insulated portions so as not to cause an electric shock and malfunctioning. (For the name of parts, refer to the above figures.)

Page 50

For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the

CAUTION! coating, pay attention to the following

points. Damaging the coating film can cause electric shock to the customers. For the caution to be heeded when . . clearing, refer to the Section of Periodic Aluminum Foil inspection Table. Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on C.R.T. surfaces. Avoid applying stickers, seals, etc. on the C.R.T. face. Do not remove aluminum foils from the C.R.T. corners. Removing the aluminum foils can cause static prevention effects to be lowered.

Monitor adjustments have been made at the time of shipment. Therefore do not make further adjustment without a justifiable reason.

caution! || Adjusting the monitor which contains high tension parts is dangerous work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunctioning. When making adjustment, utilize a resinous Alignment Rod. Servicing with bare hands or using conductive tools can cause electric shock.

12 - 2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES

Static preventive coating is applied to the CRT surfaces. Peeling off this coating can cause electric shock. When cleaning, pay attention to

CAUTION! the following points:

Remove smears by using a dry, soft cloth (flannels, etc.). Do not use a Coarse gauze, etc. For smear removing solvent, alcohol (ethanol) is recommended. When using chemical detergent, e sure to folow instructions below: Dilute chemical detergent with water and dip a soft cloth in and then thoroughly wring it to wipe smears off. Do not use a chemical detergent containing an abrasive, powder or bleaching agent. Do not use alkaline chemical detergents such as “glass cleaner” available on the market or solvents such as thinner, etc. Do not rub or scratch the CRT face with hard items such as scrub brushes, etc.

Clean the CRT surfaces once a week. When cleaning, pay attention to the above cautions so that the antistatic coating will not come off.

Page 51

12 - 3 ADJUSTMENT METHOD

@ Monitor adjustments are made at the time of shipment. Therefore, do not make further adjustments without a justifiable reason.

WARNING! Adjusting a monitor which contains high tension parts is dangerous work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunction. When making adjustments, utilize a resinous Alignment Rod. Servicing with bare hands or using tools made of conductive material can cause electric shock.

R-GAIN

G-GAIN .......... Controls colors.

B-GAIN

BRIGHT.......... Controls screen brightness. H. SIZE esses Controls horizontal screen size.

... Provides horizontal synchronization, i.e., controls right/left hold. H. POSL........... Controls horizontal display position on screen. V. SIZE ........... Controls vertical screen size.

V. HOLD.......... Provides vertical synchronization, i.e., controls up-down hold. V. POST Controls vertical display position on screen. CONTRAST.... Adjusts image contrast. oO) @ @ @ ©

  • H. HOLD @)

2) 0) cn)

Page 52
  • REPLACING THE FLUORESCENT LAMP

@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Fluorescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to use a step which is ina secure and stable condition. Not using a step or using an unstable step can cause violent falling accidents.

CAUTION!

13 -1 METHOD OF REPLACEMENT

©) Take out the 2 Truss Screws and remove the Plate Holder.

©) Lower the Billboard Plate and replace the Fluorescent Lamp.

Billboard Plate

Fluorescent Lamp 208 Local Purchase

Plate Holder

“ts, oN TRUSS SCREW(2), chrome SY M4 x8 Ay

Page 53
  • PERIODIC INSPE

CTION TABLE

The items listed below require periodic checks and maintenance in order to retain the performance of this machine and ensure safe operation.

WARNING!

pay-basis.

@ Be sure to check once a year to see if Power Cords are damaged, the Plug is Plug, etc. Using the product when dust has accumulated can cause a fire or

securley inserted, dust is accumulated between the Socket Outlet and the Power

electrical shock. @ Once a year, request an interior cleaning from the place of contact stated herin or from the Distributer from which the product was purchased. Using the product when dust has accumulated in the interior can result in a fire or short circuit accident. Note that cleaning the interior parts can be performed on an individual

CABINET DESCRIPTION Check Adjusters’ contact with surface. PERIOD Dail: CONTROL MECHANISM Check VOLUME Value. Monthly LEVER UNIT Check SW. Monthly Check VOLUME Value. Monthl. GREASING Trimonthly PEDAL UNIT Check VOLUME Value. Monthl COIN CHUTE TOWER Check COIN SWes. Monthly Coin insertion test. Monthly COIN SELECTOR cleaning. Trimonthly MONITOR Cleaning CRT face. Weekly Check Adjustments. Monthly or when moving SEAT Antistatic measures. Bimonthly GAME BD MEMORY TEST. Monthly Setting check. INTERIOR Cleaning.

Annually

POWER PLUG Inspection and cleaning. CABINET SURFACES Cleaning.

CLEANING CABINET SURFACES

If the cabinet is badly stained, use a cl As occasion arises

loth which is dipped in the chemical detergent liquid diluted with water and then squezzed dry. Do not use thinner, benzine, alcohol or chemical dustcloths, as these can damage the Cabinet surfaces.

SEAT (Greasing to Seat Rail Portion)

Move the Seat to the rearmost position and apply spray grease to the portion shown at the right once every 3 months, using NOK KLUBER L60 or GREASE MATE (Part No. 090-0066). . After greasing, move the seat forward and backward a few times to allow the grease to be applied uniformly. Be sure to wipe off any grease that contacts the surfaces of the PROTECTIVE RUBBER on the Seat Rail, and any excess grease. fi

Page 54
  • TROUBLESHOOTING

Should trouble occur, first check wiring connections.

PROBLEMS CAUSE COUNTERMEASURES When Main SW is The power is not on. ON, there is no activation. Power supply/voltage is incorrect.

AC main fuse causes the power to be cut off due to momentary overload. Firmly insert the plug into the outlet.

Make sure that the power supply/voltage is correct. Check the fuse. Remove the cause of overload and replace the fuse.

Irregular sound Greasing to gear mesh portion is not emitted from satisfactory, or extraneous matter inside Rear Cabinet mixed in. Apply greasing or eliminate extraneous matter.

No sound is emitted. | Sound Volume adjustment is not correct.

Sound BD and Amp are malfunctioning. Adjust the SWITCH UNIT’s speaker volume.

Perform SOUND TEST to find and replace defective parts.

No sound fromIn correct Cabinet Type Setting.Correct Cabinet Type Setting.

Cockpit.

The FluorescentThe Fluorescent tube is burnt out.Replace the Fluorescent tube.

lamp does not light up.

The image coloring Affected by C.R.T. magnetization. on the MONITOR Press the DEMAG. SW on the SWITCH UNIT.

RUDDER PEDAL, Volume malfunctioning. and THRUST LEVER] is not satisfactory. ADJUST GEAR mesh is incorrect.

is incorrect.Incorrect monitor adjustment.Make appropriate adjustments.
Operation ofDeviation of Volume.Adjust Volume value in the TEST mode.

CONTROL WHEEL, Replace the Volume.

Adjust ADJUST GEAR mesh.

CIRCUIT PROTECTOR

Functions due to the activation of bimetal. To restore the function, wait approximately one minute or longer until the bimetal cools off, and press the button.

Page 55
  • GAME BOARD

@ In order to prevent an electrical shock, be sure to turn power off before performing work. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. with the same settings made at the time of shipment. Do not expose the Game BD, etc.

CAUTION! without good reason.

16-1 LOCATING THE GAME BOARD

® Turn power off.

@ Take out a total of 6 Truss Screws and unlock to remove the Seat.

(6) The GAME BOARD is located at the

position shown in the photo below.

i TRUSS SCREW (4) black M5 x 12

For performing work, use 2 or more workers.

Page 56

16 -2 COMPOSITION OF GAME BOARD

Be sure to use the specified settings for the DIP SWes on the Filter Board. Failure to do so may cause irregularities or malfunctioning, such as unsatisfactory images displayed on the screen.

IMPORTANT!

ASSY CASE NAO USA (840-0005D-05)

a 849-O001A-01 ASSY CASE NAOME MAIN 2D USA

DIP SW SETTING

In this product, be sure to set all of the DIP SWes to OFF.

Page 57
  • DESIGN RELATED PARTS

For the Warning Display stickers, refer to Section |.

—~ (a)

\

  • (2)

_/ ae) (o>) fs F ie I ge |

Page 58

DESIGN RELATED PARTS

ITEM NO.

CIDwWNS Re} PART NO.

APC-0202 422-0748-01 APC-3110-A APC-1551-A APC-1571-A 421-9749-02 APC-1501-A APC-1501-B APC-1511-A 422-0751-91-01 APC-2502-D APC-2502-C APC-2502-B SPG-1201-E APC-1078 APC-3005 APC-1583 DESCRIPTION

BILLBOARD PLATE STD SUB INSTR SH APC STD ENG STICKER SEAT BACK STICKER SIDE L STICKER SIDER STICKER SEGA LOGO BLOW WHITE STICKER BASE L APC STICKER BASE R APC STICKER BASE LID PLAY INSTR SH APC STD ENG DESIGN PL METER C DESIGN PL METER B DESIGN PL METER A METER PANEL STICKER CENTER MARK STICKER THRUST SW PLATE STD

Page 59

18.PARTS LIST

@ TOP ASSY APC STD

bie (2), Q0a¥ LEX

Page 60

@ TOP ASSY APC STD

ITEM NO.

CIDARWNE Wee eee ey SEREARBNHS PART NO.

APC-10001 APC-0200 APC-0300 RAL-0006 SDW-0005 SDW-0006 SDW-0007 SDW-0008 SDW-0009 INY-0004 DYN-0008 DYN-O0011 421-7308-~ 422-0748-01 SGM-3863 APC-0004 APC-0012X

030-000820-SB 068-852216-OB 000-P00408-WB 000-T00512-OB 010-P00408-F 008-T00412-OB 050-F00800 000-T00416-OC 060-F00800-OB DESCRIPTION

ASSY COCKPIT ASSY BILLBOARD STD ASSY COINCHUTE TOWER BLIND CAP AC COVER AC LID CONNECTOR COVER WIRE COVER TOWER COVER BACK LID INY BACK LID B DENOMI PLATE W/O ORIGINAL DENOMI SH 1GAME ~ SUB INSTR SH APC STD ENG POLTHN COVER 950 X 1800 X 1700 BILLBOARD HOOK BILLBOARD HOLDER STD

HEX BLT W/S BLK M8 X 20 FLT WSHR BLK 8.5-22 X 1.6 MSCR PH W/FS BLK M4 X 8 M SCR TH BLK M5 X 12 S-TITE SCR PH W/F M4 X 8

TMP PRF SCR TH BLK M4 X 12

FLG NUT M8 S=12 M SCR TH CRM M4 X 16 FLT WSHR BLK M8

Page 61

@ ASSY BILLBOARD STD (APC-0200)

ITEM NO. PART NO. DESCRIPTION

1APC-0201BILLBOARD BASE
2APC-0202BILLBOARD PLATE STD
3APC-0203PLATE HOLDER
4APC-0204CONNECTOR LID
5APC-0205BOLT LID
201000-T00408-OCM SCR TH CRM M4 X 8
Page 62

@ ASSY COINCHUTE TOWER (APC-0300)

Page 63

© ASSY COINCHUTE TOWER (APC-0300)

ITEM NO. PART NO. DESCRIPTION

1APC-0301COINCHUTE TOWER
2DRT-0301COIN METER BRKT
4SDW-0360SW UNIT
5DP-1167TNG LKG
6105-5172CHUTE PLATE DOUBLE
7253-5366CASH BOX
9421-7501-02STICKER 6.3V 0.15A
12APC-0303CONN PNL TOWER STD
101220-5482-91-~ASSY C.C 2DR ~

220-5237-92-~ ASSY C.C 2DR ~

1022205643-01MAG CNTR DCSV 6P WH MZ-674-D04
103220-5574CAM LOCK W/KEYS
104220-5575CAM LOCK MASTER W/O KEY
201000-P00408-WMSCR PG W/FS M4 X 8
Page 64

@® SW UNIT (SDW-0360)

ITEM NO. PART NO.

1 KR-1060

101 509-5028 102 220-5179 103 601-0042 DESCRIPTION

SW BRACKET

SW PB 1M VOL CONT B-5K OHM KNOB 22MM

Page 65

M4(M SCR) Under 10kgt+ cm © ASSY COCKPIT (APC-10001)

Page 66

© ASSY COCKPIT (APC-10001)

ITEM NO.

CIADARwKWNHE pose PART NO.

APC-1500 APC-1550 APC-1570 APC-1600 APC-2200 APC-20001 SPG-1008 APC-1088 APC-1089 SDW-1023 SDW-1024 APC-1019 APC-1080 TTR-1067X DYN-1025 SPG-1005 INY-1016 RAL-2007 RAL-2008 INY-1015

200-5787 280-5112 280-5113 280-5114 280-5185-6

030-000850-SB 068-852216-OB 030-000820-SB 060-F00800-OB 000-F00508 050-F00600 000-P00408-WB 030-000840-SB 008-B00830-OB 068-552016-OB 000-T00512-OB 000-T00530-OB 000-P00312-WB DYN-1019 060-S00800-OB 000-T00408-OB 008-B00820-OB 050-F00800 DESCRIPTION

ASSY MAIN BASE ASSY MONITOR COVER L ASSY MONITOR COVER R ASSY SEAT STD PEDAL UNIT ASSY CTRL PNL ROOF LID SIDE PNL L SIDE PNLR FOOT COVER L FOOT COVER R MONITOR STAND WIRE COVER BOX MONITOR MASK RUBBER CUSHION MASK HOLDER MONITOR SUPPORT RUBBER HOLDER R TWIN RUBBER HOLDER L TWIN CRT ADJUST PANEL

ASSY CLR DSPL 29TYPE 31K 100V BUSH FOR TV COLLAR FOR TV SPACER 6.4-25 X 2 SPACER TUBE L=6

HEX BLT W/S BLK M8 X 50 FLT WSHR BLK 8.5-22 X 1.6 HEX BLT W/S BLK M8 X 20 FLT WSHR BLK M8 MSCR FH M5 X8 FLG NUT M6 M SCR PH W/FS BLK M4 X 8 HEX BLT W/S BLK M8 X 40 TMP PRF SCR BH BLK M8 X 30 FLT WSHR BLK 5.5-20 X 1.6 MSCR TH BLK M5 X 12 M SCR TH BLK M5 X 30 MSCR PH W/FS BLK M3 X 12 FLT WASHER M8 SPR WSHR BLK M8 MSCR TH BLK M4 X 8 TMP PRF SCR BH BLK M8 X 20 FLG NUT M8 S=12

Page 67

© ASSY MAIN BASE (APC-1500)

Page 68

© ASSY MAIN BASE (APC-1500)

ITEM NO.

UbwWNe PART NO.

APC-1520 APC-1530 APC-4500 APC-4600 APC-1502

260-0011-02

000-P00425-W 068-441616 030-000616-SB 060-F00600-OB 000-P00408-WB 000-P00350 060-F00300 060-S00300 DESCRIPTION

ASSY BASE BOX AC UNIT ASSY MAIN BD STD ASSY PWR SPLY STD FOOT BASE

AXIAL FLOW FAN AC100V 50-60HZ

M SCR PH WI/FS M4 X 25 FLT WSHR 4.4-16 X 1.6 HEX BLT W/S BLK M6 X 16 FLT WSHR BLK M6 M SCR PH W/FS BLK M4 X 8 M SCR PH M3 X 50 FLT WSHR M3 SPR WSHR M3

Page 69

@ ASSY BASE BOX (APC-1520)

Note: Assemble (3 and ©, then fasten to D.

ITEM NO. PART NO. DESCRIPTION

1 APC-1501 MAIN BASE

2DYN-2004LOCK TNG
3APC-1523BASE LID BRKT
4APC-1510ASSY BASE LIDR

5 APC-1522 FLOOR MAT

6APC-1521BASE LID F
7DYN-2007XLID EDGE L
8DYN-2009XLID EDGER
101220-5575CAM LOCK MASTER W/O KEY
201000-T00512-OBM SCR TH BLK M5 X 12
202031-000514-OBCRG BLT BLK M5 X 14
203050-F00500FLG NUT M5
204031-000414-OCCRG BLT CRM M4 X 14
205050-F00400FLG NUT M4
Page 70

® MAIN BASE (APC-1501)

Page 71

MAIN BASE (APC-1501)

ITEM NO.

ANnukwWNe PART NO.

DYN-2002X-A APC-1501-A APC-1501-B SDW-1103 601-5699X 601-5471

030-000816-S 050-H01600-OB DESCRIPTION

MAIN BASE BLANK STICKER BASE L APC STICKER BASE R APC BASE FOOT LEG ADJUSTER BOLT M16 X 75 CASTER

HEX BLT W/S M8 X 16 HEX NUT BLK M16

Page 72

© ASSY BASE LID R (APC-1510)

ITEM NO. PART NO.

DYN-2011 DYN-2012 DYN-2013 DYN-2014 APC-1511

601-7551

045-C02520 031-000510-OB 050-F00500 DESCRIPTION

LOCK ROD A LOCK ROD B LOCK ARM ROD HOLDER BASE LIDR

LOCK HANDLE

COT PIN 2.5 X 20 CRG BLT BLK M5 X 10 FLG NUT M5

Page 73

(9 AC UNIT (APC-1530)

‘105

ITEM NO. PART NO. DESCRIPTION

1APC-1531AC BRKT
101214-0202AC INLET PANEL TYPE
105509-5453-91-V-BSW ROCKER J8 V-B
Page 74

() ASSY MAIN BD STD (APC-4500)

ITEM NO. PART NO.

APC-4501 840-0005D-05 837-13551-92

400-5397

000-P00416-W 011-P00325 O11-T03512

Note: Make sure that there 1s no parts. wing. etc. in the siash mark pormons.

DESCRIPTION

WOODEN MAIN BASE STD ASSY CASE NAO APC W/O JAL I/O CONTROL BD FOR JVS

SW REGU FOR JVS

M SCR PH W/FS M4 X 16 TAP SCR PH 3 X 25 TAP SCR TH 3.5 X 12

Page 75

(2 ASSY PWR SPLY STD (APC-4600)

Cait) — 2102) Eh ee oA

DOOD0000 DO0D0U0

oongn000 ODdONeOD 00000000 oDD00000

2-020 Nota Make sure that thare is no nants wirinn air

ITEM NO. PART NO. DESCRIPTION

1 APC-4601 WOODEN PWR SPLY BASE STD

101560-5426-HXFMR 100-120V 100V 5.5A
102838-11856CE-02CONNECT BD W/FUSE 6.3A CE
103601-10369STEREO PWR AMP 47
201000-P00416-WM SCR PH W/FS M4 X 16
202011-P00325TAP SCR PH 3 X 25
204011-T03512TAP SCR TH 3.5 X 12

=)

Page 76

(©) ASSY MONITOR COVER L (APC-1550)

ITEM NO. PART NO. DESCRIPTION

1APC-1550COVER PANEL L
2APC-1560ASSY SPEAKER L
3DYN-1032MASK BRKT
201000-P00408-WM SCR PH W/FS M4 X 8
Page 77

© ASSY SPEAKER L (APC-1560)

ITEM NO. PART NO. DESCRIPTION

1 APC-1561 SPEAKER BRKT

101 130-5156 SPEAKER BOX 80HM 20W

201 000-P00512-W M SCR PH W/FS M5 X 12

Page 78

© ASSY MONITOR COVER R (APC-1570)

ITEM NO. PART NO. DESCRIPTION

1 APC-1571 COVER PANEL R

2 APC-1565 ASSY SPEAKER R

3 DYN-1032 MASK BRKT

202 000-P00408-W M SCR PH W/FS M4 X 8

Page 79

(© ASSY SPEAKER R (APC-1565)

\ \

ITEM NO. PART NO. DESCRIPTION

1APC-1561SPEAKER BRKT
101130-5156SPEAKER BOX 80HM 20W
201M SCR PH W/FS MS X 12M SCR PH W/FS MS X 12
Page 80

@ ASSY SEAT STD (APC-1600)

Page 81

@ Assy SEAT STD (APC-1600)

ITEM NO.

Dose werd]Anawne PART NO.

APC-3101 APC-3112 APC-3103 STC-1612 APC-3105 APC-3113 APC-3107 APC-3110 DYN-2131 DYN-2132 APC-3114 GHO-3705

601-9059 601-9060

000-T00408-OB 000-T00412-OC 030-0008 16-S 030-000850-S 050-H00800 060-S00800 068-441616-OC 068-852216 DESCRIPTION

SEAT BASE SEAT FRAME STD SEAT MOUNT TRAY PROTECT RUBBER SAFETY GUARD FRONT SAFETY GUARD REAR STD SAFETY GUARD SIDE SEAT REAR COVER STD UPPER SEAT LOWER SEAT SEAT BASE REAR FLT WSRR 8.5-26 X 3.2

SEAT RAIL L SEAT RAILR

M SCR TH BLK M4 X 8 M SCR TH CRM M4 X 12 HEX BLT W/S M8 X 16 HEX BLT W/S M8 X 50 HEX NUT M8 SPR WSHR M8 FLT WSHR CRM 44-16 X 1.6 FLT WSRR 8.5-22 X 1.6

Page 82

PEDAL UNIT (APC-2200)

Page 83

PEDAL UNIT (APC-2200)

ITEM NO.

CIDANWHRWNE BIRGESSISS PART NO.

APC-2201 APC-2202 APC-2203 APC-2204 APC-2205 APC-2206 APC-2207 APC-2208 APC-2209X APC-2210X APC-2211 APC-2212 APC-2213 AIN-2108 SAS-1178 TTR-2010 601-6450 601-6555

100-5120 220-5484 601-8917 100-5168 100-5070

000-P004.10-W 000-P00408-WB 000-T00408-OB 028-A00410-P 030-000620-S 030-000816-S 030-000830-S 050-F00400 050-H00800 050-H01400 060-S00800 060-S01400 060-F00800 068-441616 068-652016 068-852216 050-F00600 000-P00406-S 060-F00400 DESCRIPTION

PEDAL BASE STOPPER SHAFT STOPPER RUBBER MAIN PIPE ARM PEDAL UPPER PEDAL LOWER PEDAL COVER PEDAL REAR L PEDAL REAR R ROSTA BRKT VOL BRKT PEDAL MECHA COVER RING FLT WSHR BLK 8.5-30 X 2 GEAR HOLDER 110 GEAR 110 GEAR =30 M=0.75

BEARING (FYH BLP 204) VOL CONT B-SK OHM ROSTA 22 (DR-S 27 X 40) BEARING 20 (NSK 6904ZZ) BEARING 15 (NSK 6002ZZ)

M SCR PH W/FS M4 X 10 M SCR PH W/FS BLK M4 X 8 M SCR TH BLK M4 X 8 SET SCR HEX SKT CUP P M4 X 10 HEX BLT W/S M6 X 20 HEX BLT W/S M8 X 16 HEX BLT W/S M8 X 30 FLG NUT M4 HEX NUT M8 HEX NUT M14 SPR WSHR M8 SPR WSHR M14 FLT WSHR M8 FLT WSHR 4.4-16 X 1.6 FLT WSRR 6.5-20 X 1.6 FLT WSRR 8.5-22 X 1.6 FLG NUT M6 M SCR PH W/S M4 X 6 FLT WSHR M4

Page 84

9 ASSY CTRL PNL (APC-20001)

Page 85

(9 ASSY CTRL PNL (APC-20001)

ITEM NO.

wNe CIDA PART NO.

APC-2501 APC-2502-01 APC-2000 APC-2100 APC-2150 APC-3250 APC-1066 APC-1078 APC-2503 APC-2504 APC-3202 APC-3203 APC-3204 APC-3206 APC-1580 APC-1582 APC-1583 APC-2505 APC-1073 SPG-2039 APC-2506 APC-3205 601-6555 APC-2014 APC-3208 APC-2508 APC-2507 APC-3005

220-5484

000-T00416-OB 060-S00800-OB 020-000820-OZ 000-T00412-OC 020-000512-HZ 060-S00500 068-441616-OC 030-000816-SB 008-T00416-OB 000-P00408-W 020-000612-OZ 060-S00600 060-F00600 028-A00404-P 000-P00412-W 050-F00400 008-T00416-OB 000-T00406-OC DESCRIPTION

CTRL PNL BASE STD CTRL PNL COVER STD EXP ASSY CONTROL MECHA ASSY YOKE ASSY VIRTUAL BUTTON ASSY LEVER MECHA YOKE COVER STICKER CENTER MARK SHIFT COVER LOWER COVER ADJUST BRKT LEVER COVER LEVER KNOB KNOB BUSH JOINT BRKT ASSY SW PLATE STD LEVER SW COVER SW PLATE STD MECHA ADJUSTER STD OUTER COLLAR SPACER RING LEVER SIDE BRKT VR BRKT LEVER GEAR Z=30 M=0.75 INSULATOR BUSH INSULATOR PAPER LEVER SPACER PIPE STD STICKER BLACK STICKER THRUST

VOL CONT B-5K OHM

M SCR TH BLK M4 X 16 SPR WSHR BLK M8 HEX SKT H CAP SCR BLK OZ M8 X 20 M SCR TH CRM M4 X 12 HEX SKT CAP SCR BLK OZ MS X 12 SPR WSHR M5 FLT WSHR CRM 4.4-16 X 1.6 HEX BLT W/S BLK M8 X 16

TMP PREF SCR TH BLK M4 X 16 HEX SKT H CAP SCR BLK OZ M6 X 12

MSCR PH W/FS M4 X 8

SPR WSHR M6 FLT WSHR M6 SET SCR HEX SKT CUP P M4 X 4 M SCR PH W/FS M4 X 12 FLG NUT M4

TMP PRF SCR TH BLK M4 X 16

M SCR TH CRM M4 X 6

Page 86

ASSY CONTROL MECHA (APC-2000)

Page 87

ASSY CONTROL MECHA (APC-2000)

ITEM NO. PART NO. DESCRIPTION

1APC-2050ASSY SLIDE BASE
2APC-2030ASSY CENTERING MECHA
3APC-2090ASSY SHAFT GUIDE
4APC-2003STOPPER RUBBER STROKE
5APC-2004STOPPER SHAFT STROKE
6APC-2012VR BRKT STROKE INSU
7APC-2006CABLE BEAR BRKT
8APC-2007STROKE DAMPER SHAFT
9601-7088-91GEAR 64
10601-10572GEAR 80
11601-8966GEAR HOLDER
12APC-2001MECHA BASE
13APC-2008SPRING HOOK
14APC-2009EXT SPRING LONG
15APC-2013VR BRKT ROLL INSU
16APC-2010INSULATOR PAPER ROLL
17APC-2011INSULATOR PAPER STROKE
18APC-2014INSULATOR BUSH
102601-10574STROKE DAMPER
103220-5484VOL CONT B-5K OHM
202060-S00800-OBSPR WSHR BLK M8
203060-F00800-OBFLT WSHR BLK M8
204.020-000820-OZHEX SKT H CAP SCR BLK OZ M8 X 20
205050-U00800U NUT M8
206000-P00408-WM SCR PH W/FS M4 X 8
207060-S00600SPR WSHR M6
208060-F00600FLT WSHR M6
209028-A00308-PSET SCR HEX SKT CUT P M3 X 8
211000-P00410-WBM SCR PH BLK W/FS M4 X 10
212020-000410-HZHEX SKT CAP SCR BLK OZ M4 X 10
213060-F00400FLT WSHR M4
214060-S00400SPR WSHR M4
Page 88

@1) ASSY CENTERING MECHA (APC-2030)

ITEM NO. PART NO. DESCRIPTION

1 APC-2031 CENTERING BASE

2 APC-2032 CENTERING GUIDE

3 APC-2033 EXT SPRING

4 APC-2034 SPRING SHAFT

5 APC-2035 SPRING COLLAR INNER

6APC-2036SPRING COLLAR OUTER
7APC-2037MUTE RUBBER
201000-P00408-WMSCR PH W/FS M4 X 8
202000-P00310-WMSCR PH WIFS M3 X 10
203250-5421FLT WSHR 3.5-12 T=1.0
204060-F00400FLT WSHR M4
Page 89

@2) ASSY SLIDE BASE (APC-2050)

wo 46452-1108 L3NOOS NOE ua )6425-(L 108 LIMOS NOE

Page 90

@2) ASSY SLIDE BASE (APC-2050)

ITEM NO.

CANWRWNH PART NO.

APC-2051 APC-2052 APC-2053 APC-2054 APC-2055 APC-2056 APC-2058 APC-2059 601-10575 601-7088-91 APC-2060 APC-2061 APC-2062 APC-2063

100-5340 100-5168 100-5341 601-10573 601-6231-B045

000-P00308-W 020-000512-HZ 060-S00500-OB 050-U00800 060-F00800-OB 000-P00408-W 000-P00312-W 060-F00400 028-A00308-P 000-T00408-OC 050-U00400 060-S00400 060-F00500-OB 029-000020 000-P00408-S DESCRIPTION

MAIN SHAFT INNER BASE HOUSING PLATE 30 HOUSING PLATE 20 STOPPER RUBBER ROLL STOPPER SHAFT ROLL SLIDE BRKT L SLIDE BRKT R RACK GEAR 64 GUARD BRKT STOPPER INNER COLLAR GUIDE PLATE

BEARING 30 (6806ZZ) BEARING 20 (NSK 6904ZZ) SLIDE RAIL ROTARY DAMPER ROLL EDGING NEW TYPE

MSCR PH W/FS M3 X 8 HEX SKT CAP SCR BLK OZ MS X 12 SPR WSHR BLK M5 U NUT M8 FLT WSHR BLK M8 MSCR PH W/FS M4 X 8 M SCR PH W/FS M3 X 12 FLT WSHR M4 SET SCR HEX SKT CUP P M3 X8 M SCR TH CRM M4 X 8 U NUT M4 SPR WSHR M4 FLT WSHR BLK M5 HEX SKT H CAP SCR M4 X 10 MSCR PH W/S M4 X 8

Page 91

@3) ASSY SHAFT GUIDE (APC-2090)

ITEM NO. PART NO. DESCRIPTION

1 APC-2091 GUIDE BUSH BRKT

APC-2093 LBRKT

201 000P00408-W MSCR PH W/FS M4 X 8

Page 92

ASSY YOKE (APC-2100)

ITEM NO. PART NO.

AUskwWnNne APC-2101 APC-2102 APC-2103 RCR-2151 RCR-2152 GLC-2036

000-P00410-OB 008-P00510-OB 000-P00208 060-F00200 DESCRIPTION

YOKE THUMB CAP TRIGGER CAP HANDLE GRIP RIGHT HANDLE GRIP LEFT STOPPER

M SCR PH BLK M4 X 10

TMP PRF SCR PH BLK M5 X 10

M SCR PH M2 X8 FLT WSHR M2

Page 93

@5) ASSY VIRTUAL BUTTON (APC-2150)

ITEM NO. PART NO. DESCRIPTION

1APC-2151XVR BUTTON BRKT
2171-6478BPC BD LIGHTING SWX5
101212-5205-12CONN JST M 12P RTA
102509-5560-Y*PB SW WIL 6V IL Y
103509-5561-S**PB SW WIL 6V 5LS
  • HAPP Part No. 55-0006-25 available ** HAPP Part No. 55-0006-42 available
Page 94

ASSY LEVER MECHA (APC-3250)

ITEM NO.

BSewmraunsewne PART NO.

APC-3251 APC-3252 APC-3253 APC-3254 APC-3255 APC-3256 APC-3257 APC-3258 TTR-2009 601-6005

601-10571

000-P00330-W 000-P00408-W 028-A00408-P 050-U00800 060-F00800 000-P00408-S DESCRIPTION

LEVER GUIDE LEVER BRKT INNER LEVER BRKT OUTER LEVER SHAFT SHUTTER PLATE STOPPER RUBBER LEVER STOPPER SHAFT LEVER ZBRKT GEAR HOLDER 80 ADJUST GEAR

ROTARY DAMPER LEVER

M SCR PH W/FS M3 X 30 MSCR PH W/FS M4 X 8 SET SCR HGEX SKT CUP P M4 X 8 U NUT M8 FLT WSHR M8 MSCR PH W/S M4 X 8

Page 95

@2) ASSY SW PLATE STD (APC-1580)

ITEM NO. PART NO. DESCRIPTION

1APC-1581SW BSE STD
101390-6640-GRLED BD-0811-12V GREEN
102390-6640-RELED BD-0811-12V RED
103509-5910ROCKER SW M-2012YG
104509-5911-GSW LEVER AT-4157 GRAY
105509-5911-RSW LEVER AT-4157 RED
108280-5185-7SPACER TUBE L=7
201050-F00300FLG NUT M3
Page 96

VISIT OUR WEBSITE!

ae (Je AGQeeass a nittp:/ Awww seusety ice com /SEGASERVICE /malnpag thst nal sla al Seger iarvce

Coin-Op Links: Star Tech Journal Amusement Industry Mega Site

‘Sega Enterprises inc, USA if you have any questions about this Home Page please Service Department E-Mail ta: Phone (650)-632-7580 Fax (650) -632-7594 darl.davidson@seu.sega.com best viewed vith imrbesence A total of PROMISE] people have accessed this page.

WE icv Si5i'31 LY2K COMPLIANCE]

Page 97

SEGA

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (650) 632-7580 phone (650) 632-7594. fax