Varkon Instruction Booklet (16P-512-103) Sept 1982
Varkon (L-1) (Williams, 1982) · Document · 16 pages · 19 sections · original scan
ffs Wiliams Ww) 16-512-103 ELECTRONICS, INC. Game No. 512 September, 1982
VARKON
INSTRUCTION BOOKLET
This booklet provides game operation, bookkeeping, game adjustment, diagnostic, and self-test procedures for VARKON. For installation and special maintenance information refer to the blue-covered game manual,
SPECIAL CONSIDERATIONS WHEN REPLACING CIRCUIT BOARDS CPU Board
- Revision level 7 CPU Boards (batteries located on lower left corner at board) of later boards must be used.
- Must be equipped with blue-labeled Flipper ROMs and blue-labeled Game ROMs.
- Jumpers W3, WI0, WIL, W14, WI7, W19, W20, and W22 must be connected. Jumpers W4, W9, W12, WIS, W16, W18, W21, and W23 must be removed. With the exception of W25, (Factory Setting Jumper) all other jumpers are not changed. Driver Board Must be equipped with zero-ohm resistors or wire jumpers (W9-W16) in place of switch matrix drive series resistors R204-R211. Sound Board Must be jumpered for ROM operation and be equipped with Sound ROM 10. Jumpers W2, W5, W7, W9, WI1O, WI2, and WIS connected; W3, W4, W6, W8, WII, and W13 removed). Power Supply Board
- Model D 8345 board required (equipped with relay).
- Fuse F4 (10A SB) for flipper solenoids must be installed. Display Boards Model C 8363 Master Display and 7-digit Slave Displays required
Game Operation
GAME OVER MODE Turn game ON, player I display shows High Score to Date and Game Over lights come on. The High Score to Date alternates between player I and player 2 displays, and all playfield lamps on both Lower Level Playfield (LLP) and Upper Level Playfield (ULP) cycle in Attract mode.
CREDIT POSTING Insert coins; sound produced, number of credits displayed. If maximum credits* level is exceeded by coin or High Score to Date, credits are posted correctly and coin lockout de-energizes until remaining credits are below maximum. No credits may be won, and coins are rejected while coin lockout is de-energized. With | credit posted single player play is possible. With 2 or more credits posted, two player play is possible, or a single player can play more than one game.
Lane Change is a trademark of Williams Electronics, Inc.
GAME START . A ball should be on both the ULP and LLP. With credits posted press 1- or 2-Player Start. The number of credits displayed is reduced appropriately, player 1 display flashes, player 2 display counts down from “50” and a ball is served into play on the ULP. This ball should be caught with a flipper and sent into play. The game program can be set to serve a no-score ball a specific number of times. If, after this number of serves, player has not yet scored points, the ball in play is considered “drained”. With only one player, the player 2 score display counts down from “30” in between subsequent balls. When two play, the other player score display counts down from “50” between turns. Completing targets 1-2-3-4-5 lights the spinner ramp chamber. Making the chamber when lit for 5,000 or more holds the ULP ball in the chamber and the other ball is ejected onto the LLP. When the LLP ball drains, the ULP ball is kicked onto the ULP to continue play.
UPPER LEVEL PLAYFIELD Bonus Advance Targets 1-2-3-4-5 and V-A-R advances the bonus. Completing K-O-N advances the bonus multiplier 2X-3X- SX-10X.
Targets 1-2-3-4-5 Completing targets lights points for 1,000, Bull’s-Eye for 25,000, and advances lighting of ramp chamber value from 5,000 to 50,000.
V-A-R Rollovers Completing V-A-R advances jet bumper value 30-300-3,000.
Lane Change™ Feature The V-A-R and K-O-N lamps can be rotated by pushing the Lane Change button on the control panel.
Extra Ball Lighting the ramp chamber for 20,000* or more and then making the chamber lights the Bull’s-Eye target for a possible Extra Ball. Extra Balls, up to 4* at one time, are also earned by exceeding adjustable score levels.
LOWER LEVEL PLAYFIELD Bonus Advance Completing targets 6-7-8-9-10 collects and advances the bonus (20-40-60-80 thousand). Making A and B targets advance the bonus multiplier (2X-3X-4X-5X).
Special Topping out the bonus at 80,000 and the multiplier at 5X scores a special 50,000 points.*
TILT Ball in play is tilted on third* closure of Plumb Bob and playfield tilts. A single slam tilt returns game to Game. Over mode.
MATCH Match digits appear* in Ball-in-Play display and Game Over lamps go off: game then enters attract mode.
*Indicates game program adjustable features. s
§ “Warning: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference, Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”
INITIATING AUTO-CYCLE MODE
- Set AUTO-UP/MANUAL-DOWN switch to AUTO-UP and depress ADVANCE pushbutton. Test 04 is indicated in Credit display and Function 00 in Match Display.
- Set switch to MANUAL-DOWN and depress ADVANCE to indicate Function 50 in the Match Display.
- Set switch to AUTO-UP and operate Credit button to indicate 15 in Player 1 Display.
- Depress ADVANCE pushbutton to start Auto-Cycle mode. Each cycle of this mode sequences thru the Display Digits Test, Sound Test (00), Lamp Test (01), and Solenoid test (02). J To terminate the test and return to game over, turn the game OFF and back ON.
CPU BOARD SELF-TEST Depress the DIAGNOSTIC pushbutton on the left side of the CPU Board. The following indications are provided. With 0 indication the game returns to the game over mode. 0 - Test Passed 1- IC13 RAM Faulty 2 - IC16 RAM Faulty 3 - ICI7 ROM 2 Faulty 4 -1C17 ROM 2 Faulty 5 - IC20 ROM | Faulty
6 - ICI4 Game ROM I Faulty
7 - 1C26 Game ROM 0 Faulty 8 - ICI9 CMOS RAM or Memory Protect Circuit Faulty 9 - Coin-door closed, Memory Protect Circuit Faulty, or IC19 CMOS RAM Faulty.
SOUND BOARD SELF-TEST Depress DIAGNOSTIC pushbutton on the top of the Sound Board. Several electronic sounds should be produced. This sequence of sounds is repeated until the game is turned OFF and back ON.
€ BOOKKEEPING AND GAME EVALUATION (Functions 01-17) 1. Set AUTO-UP/MANUAL-DOWN switch to AUTO-UP and depress ADVANCE pushbutton. Test 04 is indicated in the credits display, Function 00 in Match display, and Game Identification in Player | display. Operate the ADVANCE pushbutton to display Functions 01 thru 04 on the Match display (See Table 1) and record the corresponding totals (number of coins and total paid credits) from the Player | display. (To review a total that has been advanced past, set switch to MANUAL-DOWN and operate the ADVANCE pushbutton). Operate the ADVANCE pushbutton to display Functions 05, 06, and 07 in the Match display and record the corresponding free credit totals from the Player 1 display. Operate the ADVANCE pushbutton to display Function 08 in the Match display. Total credits is indicated in the Player 1 display and total free credits in the Player 2 display. . Operate the ADVANCE pushbutton to display Function 09 thru 12 in the Match display and record the corresponding totals from the Player 1 display. Operate the ADVANCE pushbutton to display Functions 13 thru 17 in the Match display aud record the corresponding totals from the Player 2 display. With switch set to MANUAL-DOWN operate ADVANCE to display Function 50 in the Match Display. From Function 50 you can return to game over or zero audit totals and return to game over. Perform step 8.a. or 8.b. as desired. . a. To return to game over, set the switch to AUTO-UP and depress ADVANCE. b. Tozero audit totals and return to game over set switch to AUTO-UP, operate the credit button to display 35 in the Player 1 display, and depress ADVANCE.
Table 1. Audit Totals
DESCRIPTION
FUNCTION | PLAYER 1 PLAYER 2 00 | Game Identification (2502 1) — 01 | Coins, Left chute — (closest to coin door hinge) _— 02 | Coin, center chute _ 03 | Coin, right chute — 04 | Total Paid Credits =
| 05 | Special Credits | — |
06 | Replay Score Credits —
| 07 | Match Credits | — |
08 Total Credits Free Credits 09 | Total Extra Balls — 10 | Ball Time in Minutes _ 11 | Total Balls Played —
| 12 | Current High Score to Date | _ |
13 Backup High Score to Date High Score to Date Credits Awarded Times exceeded Times exceeded Times exceeded Times exceeded 14 Extra Ball 1 Score 15 | Extra Ball 2 Score 16 Extra Ball 3 Score 17 Extra Ball 4 Score
GAME ADJUSTMENT PROCEDURE (Functions 13-41) Coin door must be open to change settings. 1, Set AUTO-UP/MANUAL-DOWN switch to AUTO-UP and depress the ADVANCE pushbutton. Test 04 is indicated in the Credits display, Function 00 in Match display, and game identification in Player | display.
- To raise Function number in Match display, operate ADVANCE pushbutton with switch set to AUTO-UP. To lower Function number, operate ADVANCE with switch set to MANUAL-DOWN.
- With desired Function indicated in Match display, raise value in player | display by operating credit button with switch set to AUTO-UP; lower value by operating credit button with switch set to MANUAL-DOWN. Value left in Player | display is the new setting. For values see Table 2, and for pricing Table 3. . Repeat steps 2 and 3 until all required adjustments have been made.
- Operate ADVANCE until Function 50 is indicated in Match display. From Function 50 you can return to game over or restore factory settings. Perform step 6 or 7 as desired.
- To return to game over, depress ADVANCE with switch set to AUTO-UP.
- To restore factory settings and zero audit totals: a, Operate Credit button with switch set to AUTO-UP until 45 is indicated in Player | Display. b. Depress ADVANCE. The game returns to Test 04, Function 00. c. Set switch to MANUAL-DOWN and depress ADVANCE to indicate Function 50. d. Set switch to AUTO-UP and depress ADVANCE.
RESETTING HIGH SCORE TO DATE
- Using game adjustment procedure, set Function 13 to the desired reset value.
- Depress HIGH SCORE RESET pushbutton.
FACTORY AUDIT TOTALS (Functions 42-49) The factory audit functions are not assigned.
GRN-GRY GRN-VIO GRN-BLU
232-1
232-2
a4
232-3 si Right ULP (10)
Lane Change |
Ramp Chamber
GRN-BLK
2J2-5
Jet Bumper
ULP
(lit value),
f Ube
Center Left
Standup Swit, ULP (10) it, Front Panel Front Panel (lt value),
t 000/ Tk Extra Ball when lit) LLP 25
ed Lane A (1000 wit, 100 winot It), ULP ‘Spinner a cor} a Rollover, ULP (1000) ULP (1000) 0 Standup Target, uLP "AoG0) a Fs Fd Butts. (100/ Figure 5. Switch Matrix
GRN-ORN 2J2-7 LP 060) LLP (1060) 10 Standup UP (080) 4 Standup Target, Hg (1000), ULP (1000) 2 Standup £ ULP (1000) 9 Standup 1 Stand Target uULP
n So) ip i660) P Gobo) uP GRN-RED 232-8 Front Panel LLP) B Standup uP (oe 6 Standuy Te 7 ‘Standup Outhole/Eject,
GRN-BRN rt, Front Panel Reset, 2J2-9 High Score
- If proper indications are obtained in Test 03 but matrix problem is suspected in game play, disconnect lamp connectors 2P5 and 2P7. Recheck in game play. Perform CPU Self-Test if problem remains. If problem is cleared, check for short between lamp matrix and jet bumper mounting brackets.
a &~e
No. Function (Score) 01 Plumb Bob Tilt, Cabinet 02 Not Used 03 1-Player Start, Front Panel 04 Right Coin Chute, Coin Door 05 Center Coin Chute, Coin Door 06 Left Coin Chute, Coin Door 07 Slam Tilt, Coin Door 08 High Score Reset, Coin Door 09 2-Player Start, Front Panel 10 Outhole/Eject, LLP IL Not Used 12 Not Used
- B Standup Target, LLP (1000) 14 A Standup Target, LLP (1000) 15 6 Standup Target, LLP (1000) 16 7 Standup Target, LLP (1000) 17 8 Standup Target, LLP (1000) 18 9 Standup Target, LLP (1000) 19 10 Standup Target, LLP (1000) 20 5 Standup Target, ULP (1000) 21 4 Standup Target, ULP (1000) 22 3 Standup Target, ULP (1000) 23 2 Standup Target, ULP (1000) 24 1 Standup Target, ULP (1000)
- Bull’s-Eye Target (100/25,000/Extra Ball when lit) LLP 26 Lane A Rollover, ULP (1000) 27 Lane V Rollover, ULP (1000) 28 Flipper Return Lane R Roliover (1000), ULP 29K Standup Target, ULP (1000) 30 © Standup Target, ULP (1000) 31 N Standup Target, ULP (1000) 32 Spinner (1000 wilit, 100 w/not lit), ULP a
- Jet Bumper (lit value), ULP 34 Ramp Chamber (lit value), ULP 35 Outhole/Bject, ULP *36 Top Left Standup Switch, ULP (10) *37 Bottom Left Standup Switch, ULP (10) +38. Center Left Standup Switch, ULP (10) 39 Lane Change Right, Front Panel 40 Lane Change Left, Front Panel *41 Right Side Kicker, ULP (10)
Lower Level Playfield Upper Level Playfield
*Left and right determinations are made with Playfield removed from game (PLAY SIDE UP) and flippers closest to observer.
Figure 4. Playfield Switch Locations and Switch Chart Table 2. Game Adjustments
“FACTORY FUNCTION | OESCRIPTION NOTES | SETTING
| 13 | | Back Up High Score to Date | 1 | | 1,000,000 | |
| 14 | | Replay 1 Score [Times exceeded] | 2 | | 500,000 | |
| 15 | Replay 2 Score [Times exceeded] | 2 | 1,000,000 | ||
| 16 | | Replay 3 Score [Times exceeded] | 2 | 1,500,000 | ||
| 17 | | Replay 4 Score [Times exceeded] | 2 | 0 | |
| 18 | | Maximum Credits | 3 | 30 | |
| 19 | | Standard and Custom Pricing Control: (00-08) | 4 | | ovo2 | |
| 20 | Left Coin Slot Muitiplier | 4 | 01/09 | |
| 21 | | Gener Coin Slot Multiplier | 4 | | oaas | |
| 22 | | Right Coin Slot Multiplier | 4 | | ove | |
| 23 | Coin Units Required for Credit | 4 | | ovos | ||
| 24 | | Coin Units Bonus Point | 4 | 0045 | ||
| 25 | | Minimum Coin Units | 4 | 00 | |
| 26 | | Match: | 00= Match ON; 01=Match OFF | 2 | o1 |
| 27 | Special: 00 = Awards Credit; 01 = Awards Extra Ball; 02 = Awards Points | 02 |
28 | Replay Scores: 00= Awards Credit, 01 = Awards Extra Ball 1
| 29 | | Maximum Plumb Bob Tilts | 03 |
| 30 | | Number of Balls (03 or 05) | 05 |
31 | Number of No Score flipper serves before end of ball: 3B Tens digit = ULP, Units digit = LLP
| 32] | Bonus Mukiptier er Meron | - | 00 |
Memory for both LLP and ULP LLP Memory only ULP Memory only No Memory LLP Memory during same ball and ULP Memory LLP Memory during same ball only ULP Memory only 07 = No Memory
| 33. | | Ramp Chamber Lamp Control | : | 04 |
00 = Memory, not reset when collected 01 = No Memory, not reset when collected 02 or 03= Value reduced by 5K for next ball, not reset when collected 04 = Memory, reset upon collection 05 = No Memory, reset upon collection 06 or 07= Value reduced by SK for next ball, reset when collected
| 34 | | Jet Bumper and Spinner Memory | - | 03 |
00 = Memory for both Spinner Memory only
Jet Bumper Memery ony
No
38 tLe ‘Targets 1-3 and Bull’s-Fye Extra Ball Lamp Memory - 02
Memory for both Extra Ball Lamp Memory only Targets 1-5 Memory only 03 = No memory
| 36 | Extra Ball Difficulty Control 00(Liberal)-09(Conservative) | 6 | 03 | |
| 37 | | LLP BONUS: 00 = No Memory | 01 = Memory | 7 | 00 |
| 38 | | Not Used | 00 | ||
| 39 | | Background and Attract Mode Sound Control | 00 |
Background & Attract Mode Attract Mode Only Background Only 03 = No sound
| 40 | High Score Credits | 1,2 | 03, |
| 41 | | Maximum Extra Balls at one time (00=No extra balts) | : | 04 |
NOTES: *
ol
7.
LLP = Lower Level Playfield
Second Factory Setting value is with jumper W25 on CPU Board connected. Description in brackets shown in Player 2 Display. Function 13 may be set to any multiple of 100,000 points. With Function 40 set to zero and Function 13 set to any score but zero, the High Score to Date feature operates but no credits are awarded. Although credits may be awarded for Replay scores (Functions 14-17) itis not recommended. Three credits are awarded for High Score to Date (Function 40). Change Function 26 to 00 to award Match credits. Setting Maximum Credits (Function 18) to zero places the game in a free play mode. With Function 19 set to 00, Functions 20-25 must be set manually. Refer to Table 3 for 8 standard pricing schemes (selected by values of 01-08 for Function 19) and custom pricing values. A“NO SCORE FLIPPER SERVE” is when a ball is ejected into play and no poiats are scored before the ball retums to the outhole, Spinner ramp shot to Ramp Chamber lights Bull's-Eye target fer Extra Ball with Ramp Chamber values needed shown below: 00=5K (1 completion of targets 1-5), 01=10K, 02 08=45K, and 09=5OK (10 completions of targets 1-5). LLP Bonus always reset when collected for 80,000.
ULP = Upper Level Playfield
5K, 03~20K, 04=25K, 05=30K, 06=35K, 07=40K,
Solenoid Test
2. From Lamp Test depress ADVANCE with the switch set to AUTO-UP. Test 02 should be indicated in the Credits display. The Match display sequences from Ol thru 25. Corresponding solenoids 01 thru 24 are pulsed. Flipper relay is de-energized with subtest 25. To continuously pulse a single solenoid set switch to MANUAL-DOWN. Operate ADVANCE pushbutton sequence through the solenoids one at a time. Set switch to AUTO-UP to resume sequencing.
Sol. No. Function
| 01 | ULP Outhole Eject | 12 | LLP General Illumination |
| 02 | LLP Outhole Eject | 13 | ULP/LLP Flipper Select |
| 03 | ULP Ramp Chamber | 14 | ULPYLLP Flipper Select |
| 04 | Rear Panel Lightning Bolt (Top) | 15 | Not Used |
| 05 | Rear Panel Lightning Bolt (Middle) | 16 | Coin Lockout |
| 06 | Rear Panel Lightning Bolt (Bottom) | 17 | ULP Jet Bumper |
| 07 | Not Used | 18 | ULP Right Side Kicker |
| 08 | Not Used | 19 | Not Used |
| 09 | Not Used | thru | |
| 10 | ULP General Illumination | 22 |
11 Cabinet General Illumination
Figure 3. Playfield Solenoid Locations and Solenoid Chart or OF DIAGNOSTIC PROCEDURES
Display Digits Test
- Set AUTO-UP/MANUAL-DOWN switch to MANUAL-DOWN and depress ADVANCE. Displays should indicate all 0's.
- Set the switch to AUTO-UP. Displays should sequence from all 0’s thru all 9’s. Comma segments should come on when odd digits are displayed.
- Tostop cycling, set switch to MANUAL-DOWN. Operate ADVANCE pushbutton to step through the tests one number at a time. Set switch to AUTO-UP to resume cycling.
Sound Test
- From Display Digits Test depress ADVANCE with the switch set to AUTO-UP. Test 00 should be indicated in the Credits display and the Match display should sequence from 00 thru 06. Different sounds should be produced for 00, 01, 02, 03, and 04. To continuously pulse a single sound, set the toggle switch to MANUAL-DOWN. Operate ADVANCE pushbutton to sequence through sounds one ata time. Set toggle switch to AUTO-UP to resume sequencing. n
sssssesssss
ssssssen 65,
05, ol OL o1 OL Oo 05,
ol ol ol oO ol FUNCTION
Ol OL
ol Ol o1 OL OL oO ol ol OL OL on OL o1
00. Table 4. Solenoid Connections
Table 3. Standard and Custom Price Settings
4/$1 or 5 x 25¢ 1/50¢, 3/S1, 4/$1.25 1/50¢, 3/$1, 7/$2 “1/50¢, 3/$1, 6/$2 /25¢, 3/50¢, 7/$1 coin only /25¢, 7/$1 coin only /25¢, 3/50¢, 6/$1 2/1DM, 5/2DM, 14/5DM.
1/20¢, 3/50¢ “1/2, 3/5F only, 8/10F only 1/25¢, 5/$1 coin only
“1/25¢, 4/1G /25¢, 6/$1 coin only
/25¢, 5/81 1/25¢, 4/$1 1/25¢, 5G 1/38, 2/58 CREDITS 2/50¢, S/S1 2/50¢, 4/$1 “1/50¢, 2/75¢, 3/4 x 25¢
2/100Y VIF, 3/2F IAF +1/SF, 2/10F “1/10F 1/50¢ +1/IDM, 3/2DM, 10/5DM
| SOL. | WIRE | DRIVER | SOLENOID | ||
| NO. | FUNCTION | COLOR | CONNECTIONS | TRANS. | PART NO. | |
| 01 | ULP Outhole Eject | GRY-BRN | | 2P11-4, 8P2-29 | QS | | SG1-23-850DC |
| 02 | LLP Outhole Bject | GRY-RED | | 2PI-5, 8P2-30, 8P5-I6 | QI7__| | SGI-23-850DC | |
| 03 | | ULP Ramp Chamber | GRY-ORN | 2P11-7, 8P2-31 | Q19_ | | SG1-23-8s0Dc |
| 04 | Rear Panel Lightning Bolt (Top) | GRY-YEL | | 2PI1-8, 9P1-10 | Qa | |
| 05 | Rear Pane! Lightning Bolt (Middle) | GRY-GRN | 2P11-9, 9PI-I1 | Cor) | ||
| 06 | Rear Panel Lightning Bolt (Bottom) | GRY-BLU | | 2PII-3, 9PI-I2 | Qs |
07 | Not Used 7 08 | Not Used ws
- | Not Used Qi
| 10 | ULP General tilumination | BRN-RED | | 2P9-7, 8P2-32 | 33 | | 5580-09613-00 | |
| 11 | Cabinet General Illumination | BRN-ORN | 2P9-1 | 35 | 5580-09613-00 | |||
| 12 | | LLP General Illumination | BRN-YEL —_| 2P9-2, 8P2-33, 8P5-15 | | Q37__| | $$80-09613-00 | |
| 13 | | ULPILLP Flipper Select | BRN-GRN | | 2P9-3, 8P2-34 | 39 | | 5580-09613-00 |
| 14 | ULP/LLP Fliper Select | BRN-BLU | | 29-4, 8P2.35 | 41 | | $580-09613-00 | |
| 15 | | Not Used | ork) | |||
| 16 | Coin Lockout | BRN-GRY | | 2P9-6, 7P1-18, 7P2-4 | 5 | | 904218-696¢ | |
| 17 | ULP Jet Bumper | BLU-BRN | | 2P12-7, 8P2-27 | @ | | SG-23.850Dc | |
| 18 | ULP Right Side Kicker | BLU-RED | | 2P12-4, 8P2-28 | @ | | SA-23-850DC |
19 | Not Used 6
- | Not Used @
| 21 | | Not Used | Qo |
- | Not Used 2
| LLP Left Flipper | WHT-BRN | ULP, §P5-18 | — | | SPL-22-400/ |
30-1000-DC
| LLP Right Flipper | WHT-ORN | ULP, 8P5-19 | — | | SFL-22-400/ |
30/1000-DC
| ULP Left Flipper | BLU-GRY | 2P12-2, 8P2-5 | — | SFL-19-4007 |
30-750-DC
| ULP Right Flipper | BLU-VIO | | 2P12-1, 8P2-4 | — | | SFL-19-400 |
40-750-DC
(OTES: 1, Coin lockout part no. is a Coinco number. 4. Typical wiring for solenoids and special switches follows.
- Special switch connections for solenoids 17 through 18 are " as follows: —Tt ee a 17—ORN-BRN—2P 13-5, 8P3-24 18ORN-RED—2P 13-3, 8P3-25
- Flipper button connections are as follows: BLK GRD Right—ORN-V10—2P12-1, 7P1-7 Left—ORN-GRY—2P12-2, 7P1-9
+
Switch Test dicated in the chart.
-Quarter “Indicates standard price settings by adjusting only Function 19. For other price settings, set Function 19 to 00 and set Functions 20 through 25 to the
1 Franc, 10 Franc, 5 Franc Quarter, Dollar, Quarier
25 Cent, COIN DOOR MECHANISM 1DM, 5DM, 2DM 20-Cent, 50-Cent Twin 100 Yen I Franc or Twin-] Franc 1 Guilder, 5 Franc, 10 Franc Twin-2 Franc 10, 20 Franc Twin-1 Sucre
T From Solenoid Test depress ADVANCE with the switch set to AUTO-UP. Test 03 should be indicated in the Credits display and any stuck switches in the Master display. As stuck switch(es) is displayed a sound is produced. The display continuously cycles through the stuck switches and as they are opened, the number is removed from the sequence. When all switches are open, the Match display is blank and the sounds stop. If all switches in a row are displayed, first verify that all are open and then check for a short to ground on the row wire. Operate switches; a sound is produced and switch number is momentarily indicated in the ball in play display. If two switches in a row are indicated with one switch closed, check for a short between the column wires; for multiple indication check column wire for short to ground. If two switches in a column are indicated with one switch closed, check for short between row wires.
i
Lamp Test ind Py Credits display and all multiplexed Jamps should flash. of BZ Fe]
| From Sound Test depress ADVANCE with the switch set to AUTO-UP. Test 01 should be indicated in the | aa | ge | we |
| us | 5 | Bad |
aE
| = | Ble 3 | 8 | |||
| Lamp | QL | g | = | ba | |
| No. Function | nib | fo | | Zag | Bega | |
| O1 | Same Player Shoots Again | da | a5 | BSg | Ba> |
| 02 | Ball in Play | > | 3 | é 3 | |
| 03. | Tilt | zZ |
04 Game Over 05 Match
| 06 | Not Used | ¢ | 2 |
07 _B Arrow, LLP 08 A Arrow, LLP 09 2X Bonus Multiplier, LLP 10 3X Bonus Multiplier, LLP 11 4X Bonus Multiplier, LLP 12 5X Bonus Multiplier, LLP 13 20 Bonus, LLP, (20,000)
YEL-BLU
2J5-5
Spinner
1000, ULP’ 2Pl
siart Button
(Front Panel)
| 14 40 Bonus, LLP, (40,000) | Zo | Bs | 55 | |
| 15 | 60 Bonus, LLP, (60,000) | woe | 5 | 58 |
| 16 | 80 Bonus, LLP, (80,000) | a3 | g | lace |
| 17 | 6 Target LLP | un | 38 | “ge |
| 18 | 7 Target LLP | 7 |
19 8 Target LLP 20 9 Target LLP 5 o
| 21 | 10 Target LLP | ¥ | _ | F | g | 8 |
22 5 Target ULP 6
| 23° | 4 Target ULP | + 5 % | as | 33 | a3 |
| 24 | 3 Target ULP | ada | & | ¥ | ¥ |
| 25 | 2 Target ULP | > | . | e |
26 1 Target ULP 27 Extra Ball, ULP
| 28 | 1K Bonus, ULP | z | 5 | ||||
| 29 | 2K Bonus, ULP | = | |||||
| 30 4K Bonus, ULP | ° 8 S)e, | |e | | | Ba, | |||
| 31 | 8K Bonus, ULP | 43) e4 | ed | ea | 85 | ||
| 32 | 16K Bonus, ULP | 52 | Ramp Chamber Lane 20,000, ULP | DA} o | 5 | ° | + |
| 33 | 2X Bonus Multiplier, ULP | 53. | Jet Bumper, ULP | > | |||
| 34 | 3X Bonus Multiplier, ULP | 54 Spinner Ramp, ULP (Nearest Spinner) | |||||
| 35 | 5X Bonus Multiplier, ULP | 55. | Spinner Ramp, ULP | ° | |||
| 36 | 10X Bonus Multiplier, ULP | 56 Spinner Ramp, ULP | Py | . | oe "loc | ||
| 37 Jet Bumper 30, ULP | 57 | Spinner Ramp, ULP | Wo| | 2s | 33 | Se | |
| 38 Jet Bumper 300, ULP | 58 | Ramp Chamber Lane, ULP | a Fb] 385 | 385 | ges | |||
| 39.» Jet Bumper 3000, ULP | 59 | Spinner Ramp, ULP | dal x2 | x2 | xs | ||
| 40 | 1-Player Start Button (Front Panel) | 60 Spinner Ramp, ULP | > | a | a | * | |
| 41 | Lane A, ULP | 61 | Spinner Ramp, ULP (Nearest Ramp Chamber) | ||||
| 42 | Lane V, ULP | 62 | Extra Ball 25,000, ULP |
43. Flipper Return Lane R, ULP *63. Left EYE Special, LLP a
| 44K, ULP | *64 | Right EYE Special, LLP | z |
| 45 | O, ULP | oo | |
| 46 N, ULP | NOTE: | "Ag | |
| 47 | Spinner 1000, ULP | LLP = Lower Level Playfield | a |
| 48 | 2-Player Start Button (Front Panel) | ULP = Upper Level Playfield | > |
49 Ramp Chamber Lane 5,000, ULP 50 Ramp Chamber *Left and right determinations are made with Playfield Lane 10,000, ULP 51 Ramp Chamber removed from game (PLAY SIDE UP) and flippers Lane 15,000, ULP closest to observer.
Figure 1. Playfield Lamp Locations Figure 2. Lamp Matrix
Lamp Test ind Py Credits display and all multiplexed Jamps should flash. of BZ Fe]
| From Sound Test depress ADVANCE with the switch set to AUTO-UP. Test 01 should be indicated in the | aa | ge | we |
| us | 5 | Bad |
aE
| = | Ble 3 | 8 | |||
| Lamp | QL | g | = | ba | |
| No. Function | nib | fo | | Zag | Bega | |
| O1 | Same Player Shoots Again | da | a5 | BSg | Ba> |
| 02 | Ball in Play | > | 3 | é 3 | |
| 03. | Tilt | zZ |
04 Game Over 05 Match
| 06 | Not Used | ¢ | 2 |
07 _B Arrow, LLP 08 A Arrow, LLP 09 2X Bonus Multiplier, LLP 10 3X Bonus Multiplier, LLP 11 4X Bonus Multiplier, LLP 12 5X Bonus Multiplier, LLP 13 20 Bonus, LLP, (20,000)
YEL-BLU
2J5-5
Spinner
1000, ULP’ 2Pl
siart Button
(Front Panel)
| 14 40 Bonus, LLP, (40,000) | Zo | Bs | 55 | |
| 15 | 60 Bonus, LLP, (60,000) | woe | 5 | 58 |
| 16 | 80 Bonus, LLP, (80,000) | a3 | g | lace |
| 17 | 6 Target LLP | un | 38 | “ge |
| 18 | 7 Target LLP | 7 |
19 8 Target LLP 20 9 Target LLP 5 o
| 21 | 10 Target LLP | ¥ | _ | F | g | 8 |
22 5 Target ULP 6
| 23° | 4 Target ULP | + 5 % | as | 33 | a3 |
| 24 | 3 Target ULP | ada | & | ¥ | ¥ |
| 25 | 2 Target ULP | > | . | e |
26 1 Target ULP 27 Extra Ball, ULP
| 28 | 1K Bonus, ULP | z | 5 | ||||
| 29 | 2K Bonus, ULP | = | |||||
| 30 4K Bonus, ULP | ° 8 S)e, | |e | | | Ba, | |||
| 31 | 8K Bonus, ULP | 43) e4 | ed | ea | 85 | ||
| 32 | 16K Bonus, ULP | 52 | Ramp Chamber Lane 20,000, ULP | DA} o | 5 | ° | + |
| 33 | 2X Bonus Multiplier, ULP | 53. | Jet Bumper, ULP | > | |||
| 34 | 3X Bonus Multiplier, ULP | 54 Spinner Ramp, ULP (Nearest Spinner) | |||||
| 35 | 5X Bonus Multiplier, ULP | 55. | Spinner Ramp, ULP | ° | |||
| 36 | 10X Bonus Multiplier, ULP | 56 Spinner Ramp, ULP | Py | . | oe "loc | ||
| 37 Jet Bumper 30, ULP | 57 | Spinner Ramp, ULP | Wo| | 2s | 33 | Se | |
| 38 Jet Bumper 300, ULP | 58 | Ramp Chamber Lane, ULP | a Fb] 385 | 385 | ges | |||
| 39.» Jet Bumper 3000, ULP | 59 | Spinner Ramp, ULP | dal x2 | x2 | xs | ||
| 40 | 1-Player Start Button (Front Panel) | 60 Spinner Ramp, ULP | > | a | a | * | |
| 41 | Lane A, ULP | 61 | Spinner Ramp, ULP (Nearest Ramp Chamber) | ||||
| 42 | Lane V, ULP | 62 | Extra Ball 25,000, ULP |
43. Flipper Return Lane R, ULP *63. Left EYE Special, LLP a
| 44K, ULP | *64 | Right EYE Special, LLP | z |
| 45 | O, ULP | oo | |
| 46 N, ULP | NOTE: | "Ag | |
| 47 | Spinner 1000, ULP | LLP = Lower Level Playfield | a |
| 48 | 2-Player Start Button (Front Panel) | ULP = Upper Level Playfield | > |
49 Ramp Chamber Lane 5,000, ULP 50 Ramp Chamber *Left and right determinations are made with Playfield Lane 10,000, ULP 51 Ramp Chamber removed from game (PLAY SIDE UP) and flippers Lane 15,000, ULP closest to observer.
Figure 1. Playfield Lamp Locations Figure 2. Lamp Matrix
Solenoid Test
2. From Lamp Test depress ADVANCE with the switch set to AUTO-UP. Test 02 should be indicated in the Credits display. The Match display sequences from Ol thru 25. Corresponding solenoids 01 thru 24 are pulsed. Flipper relay is de-energized with subtest 25. To continuously pulse a single solenoid set switch to MANUAL-DOWN. Operate ADVANCE pushbutton sequence through the solenoids one at a time. Set switch to AUTO-UP to resume sequencing.
Sol. No. Function
| 01 | ULP Outhole Eject | 12 | LLP General Illumination |
| 02 | LLP Outhole Eject | 13 | ULP/LLP Flipper Select |
| 03 | ULP Ramp Chamber | 14 | ULPYLLP Flipper Select |
| 04 | Rear Panel Lightning Bolt (Top) | 15 | Not Used |
| 05 | Rear Panel Lightning Bolt (Middle) | 16 | Coin Lockout |
| 06 | Rear Panel Lightning Bolt (Bottom) | 17 | ULP Jet Bumper |
| 07 | Not Used | 18 | ULP Right Side Kicker |
| 08 | Not Used | 19 | Not Used |
| 09 | Not Used | thru | |
| 10 | ULP General Illumination | 22 |
11 Cabinet General Illumination
Figure 3. Playfield Solenoid Locations and Solenoid Chart or OF DIAGNOSTIC PROCEDURES
Display Digits Test
- Set AUTO-UP/MANUAL-DOWN switch to MANUAL-DOWN and depress ADVANCE. Displays should indicate all 0's.
- Set the switch to AUTO-UP. Displays should sequence from all 0’s thru all 9’s. Comma segments should come on when odd digits are displayed.
- Tostop cycling, set switch to MANUAL-DOWN. Operate ADVANCE pushbutton to step through the tests one number at a time. Set switch to AUTO-UP to resume cycling.
Sound Test
- From Display Digits Test depress ADVANCE with the switch set to AUTO-UP. Test 00 should be indicated in the Credits display and the Match display should sequence from 00 thru 06. Different sounds should be produced for 00, 01, 02, 03, and 04. To continuously pulse a single sound, set the toggle switch to MANUAL-DOWN. Operate ADVANCE pushbutton to sequence through sounds one ata time. Set toggle switch to AUTO-UP to resume sequencing. n
sssssesssss
ssssssen 65,
05, ol OL o1 OL Oo 05,
ol ol ol oO ol FUNCTION
Ol OL
ol Ol o1 OL OL oO ol ol OL OL on OL o1
00. Table 4. Solenoid Connections
Table 3. Standard and Custom Price Settings
4/$1 or 5 x 25¢ 1/50¢, 3/S1, 4/$1.25 1/50¢, 3/$1, 7/$2 “1/50¢, 3/$1, 6/$2 /25¢, 3/50¢, 7/$1 coin only /25¢, 7/$1 coin only /25¢, 3/50¢, 6/$1 2/1DM, 5/2DM, 14/5DM.
1/20¢, 3/50¢ “1/2, 3/5F only, 8/10F only 1/25¢, 5/$1 coin only
“1/25¢, 4/1G /25¢, 6/$1 coin only
/25¢, 5/81 1/25¢, 4/$1 1/25¢, 5G 1/38, 2/58 CREDITS 2/50¢, S/S1 2/50¢, 4/$1 “1/50¢, 2/75¢, 3/4 x 25¢
2/100Y VIF, 3/2F IAF +1/SF, 2/10F “1/10F 1/50¢ +1/IDM, 3/2DM, 10/5DM
| SOL. | WIRE | DRIVER | SOLENOID | ||
| NO. | FUNCTION | COLOR | CONNECTIONS | TRANS. | PART NO. | |
| 01 | ULP Outhole Eject | GRY-BRN | | 2P11-4, 8P2-29 | QS | | SG1-23-850DC |
| 02 | LLP Outhole Bject | GRY-RED | | 2PI-5, 8P2-30, 8P5-I6 | QI7__| | SGI-23-850DC | |
| 03 | | ULP Ramp Chamber | GRY-ORN | 2P11-7, 8P2-31 | Q19_ | | SG1-23-8s0Dc |
| 04 | Rear Panel Lightning Bolt (Top) | GRY-YEL | | 2PI1-8, 9P1-10 | Qa | |
| 05 | Rear Pane! Lightning Bolt (Middle) | GRY-GRN | 2P11-9, 9PI-I1 | Cor) | ||
| 06 | Rear Panel Lightning Bolt (Bottom) | GRY-BLU | | 2PII-3, 9PI-I2 | Qs |
07 | Not Used 7 08 | Not Used ws
- | Not Used Qi
| 10 | ULP General tilumination | BRN-RED | | 2P9-7, 8P2-32 | 33 | | 5580-09613-00 | |
| 11 | Cabinet General Illumination | BRN-ORN | 2P9-1 | 35 | 5580-09613-00 | |||
| 12 | | LLP General Illumination | BRN-YEL —_| 2P9-2, 8P2-33, 8P5-15 | | Q37__| | $$80-09613-00 | |
| 13 | | ULPILLP Flipper Select | BRN-GRN | | 2P9-3, 8P2-34 | 39 | | 5580-09613-00 |
| 14 | ULP/LLP Fliper Select | BRN-BLU | | 29-4, 8P2.35 | 41 | | $580-09613-00 | |
| 15 | | Not Used | ork) | |||
| 16 | Coin Lockout | BRN-GRY | | 2P9-6, 7P1-18, 7P2-4 | 5 | | 904218-696¢ | |
| 17 | ULP Jet Bumper | BLU-BRN | | 2P12-7, 8P2-27 | @ | | SG-23.850Dc | |
| 18 | ULP Right Side Kicker | BLU-RED | | 2P12-4, 8P2-28 | @ | | SA-23-850DC |
19 | Not Used 6
- | Not Used @
| 21 | | Not Used | Qo |
- | Not Used 2
| LLP Left Flipper | WHT-BRN | ULP, §P5-18 | — | | SPL-22-400/ |
30-1000-DC
| LLP Right Flipper | WHT-ORN | ULP, 8P5-19 | — | | SFL-22-400/ |
30/1000-DC
| ULP Left Flipper | BLU-GRY | 2P12-2, 8P2-5 | — | SFL-19-4007 |
30-750-DC
| ULP Right Flipper | BLU-VIO | | 2P12-1, 8P2-4 | — | | SFL-19-400 |
40-750-DC
(OTES: 1, Coin lockout part no. is a Coinco number. 4. Typical wiring for solenoids and special switches follows.
- Special switch connections for solenoids 17 through 18 are " as follows: —Tt ee a 17—ORN-BRN—2P 13-5, 8P3-24 18ORN-RED—2P 13-3, 8P3-25
- Flipper button connections are as follows: BLK GRD Right—ORN-V10—2P12-1, 7P1-7 Left—ORN-GRY—2P12-2, 7P1-9
+
Switch Test dicated in the chart.
-Quarter “Indicates standard price settings by adjusting only Function 19. For other price settings, set Function 19 to 00 and set Functions 20 through 25 to the
1 Franc, 10 Franc, 5 Franc Quarter, Dollar, Quarier
25 Cent, COIN DOOR MECHANISM 1DM, 5DM, 2DM 20-Cent, 50-Cent Twin 100 Yen I Franc or Twin-] Franc 1 Guilder, 5 Franc, 10 Franc Twin-2 Franc 10, 20 Franc Twin-1 Sucre
T From Solenoid Test depress ADVANCE with the switch set to AUTO-UP. Test 03 should be indicated in the Credits display and any stuck switches in the Master display. As stuck switch(es) is displayed a sound is produced. The display continuously cycles through the stuck switches and as they are opened, the number is removed from the sequence. When all switches are open, the Match display is blank and the sounds stop. If all switches in a row are displayed, first verify that all are open and then check for a short to ground on the row wire. Operate switches; a sound is produced and switch number is momentarily indicated in the ball in play display. If two switches in a row are indicated with one switch closed, check for a short between the column wires; for multiple indication check column wire for short to ground. If two switches in a column are indicated with one switch closed, check for short between row wires.
i
- If proper indications are obtained in Test 03 but matrix problem is suspected in game play, disconnect lamp connectors 2P5 and 2P7. Recheck in game play. Perform CPU Self-Test if problem remains. If problem is cleared, check for short between lamp matrix and jet bumper mounting brackets.
a &~e
No. Function (Score) 01 Plumb Bob Tilt, Cabinet 02 Not Used 03 1-Player Start, Front Panel 04 Right Coin Chute, Coin Door 05 Center Coin Chute, Coin Door 06 Left Coin Chute, Coin Door 07 Slam Tilt, Coin Door 08 High Score Reset, Coin Door 09 2-Player Start, Front Panel 10 Outhole/Eject, LLP IL Not Used 12 Not Used
- B Standup Target, LLP (1000) 14 A Standup Target, LLP (1000) 15 6 Standup Target, LLP (1000) 16 7 Standup Target, LLP (1000) 17 8 Standup Target, LLP (1000) 18 9 Standup Target, LLP (1000) 19 10 Standup Target, LLP (1000) 20 5 Standup Target, ULP (1000) 21 4 Standup Target, ULP (1000) 22 3 Standup Target, ULP (1000) 23 2 Standup Target, ULP (1000) 24 1 Standup Target, ULP (1000)
- Bull’s-Eye Target (100/25,000/Extra Ball when lit) LLP 26 Lane A Rollover, ULP (1000) 27 Lane V Rollover, ULP (1000) 28 Flipper Return Lane R Roliover (1000), ULP 29K Standup Target, ULP (1000) 30 © Standup Target, ULP (1000) 31 N Standup Target, ULP (1000) 32 Spinner (1000 wilit, 100 w/not lit), ULP a
- Jet Bumper (lit value), ULP 34 Ramp Chamber (lit value), ULP 35 Outhole/Bject, ULP *36 Top Left Standup Switch, ULP (10) *37 Bottom Left Standup Switch, ULP (10) +38. Center Left Standup Switch, ULP (10) 39 Lane Change Right, Front Panel 40 Lane Change Left, Front Panel *41 Right Side Kicker, ULP (10)
Lower Level Playfield Upper Level Playfield
*Left and right determinations are made with Playfield removed from game (PLAY SIDE UP) and flippers closest to observer.
Figure 4. Playfield Switch Locations and Switch Chart Table 2. Game Adjustments
“FACTORY FUNCTION | OESCRIPTION NOTES | SETTING
| 13 | | Back Up High Score to Date | 1 | | 1,000,000 | |
| 14 | | Replay 1 Score [Times exceeded] | 2 | | 500,000 | |
| 15 | Replay 2 Score [Times exceeded] | 2 | 1,000,000 | ||
| 16 | | Replay 3 Score [Times exceeded] | 2 | 1,500,000 | ||
| 17 | | Replay 4 Score [Times exceeded] | 2 | 0 | |
| 18 | | Maximum Credits | 3 | 30 | |
| 19 | | Standard and Custom Pricing Control: (00-08) | 4 | | ovo2 | |
| 20 | Left Coin Slot Muitiplier | 4 | 01/09 | |
| 21 | | Gener Coin Slot Multiplier | 4 | | oaas | |
| 22 | | Right Coin Slot Multiplier | 4 | | ove | |
| 23 | Coin Units Required for Credit | 4 | | ovos | ||
| 24 | | Coin Units Bonus Point | 4 | 0045 | ||
| 25 | | Minimum Coin Units | 4 | 00 | |
| 26 | | Match: | 00= Match ON; 01=Match OFF | 2 | o1 |
| 27 | Special: 00 = Awards Credit; 01 = Awards Extra Ball; 02 = Awards Points | 02 |
28 | Replay Scores: 00= Awards Credit, 01 = Awards Extra Ball 1
| 29 | | Maximum Plumb Bob Tilts | 03 |
| 30 | | Number of Balls (03 or 05) | 05 |
31 | Number of No Score flipper serves before end of ball: 3B Tens digit = ULP, Units digit = LLP
| 32] | Bonus Mukiptier er Meron | - | 00 |
Memory for both LLP and ULP LLP Memory only ULP Memory only No Memory LLP Memory during same ball and ULP Memory LLP Memory during same ball only ULP Memory only 07 = No Memory
| 33. | | Ramp Chamber Lamp Control | : | 04 |
00 = Memory, not reset when collected 01 = No Memory, not reset when collected 02 or 03= Value reduced by 5K for next ball, not reset when collected 04 = Memory, reset upon collection 05 = No Memory, reset upon collection 06 or 07= Value reduced by SK for next ball, reset when collected
| 34 | | Jet Bumper and Spinner Memory | - | 03 |
00 = Memory for both Spinner Memory only
Jet Bumper Memery ony
No
38 tLe ‘Targets 1-3 and Bull’s-Fye Extra Ball Lamp Memory - 02
Memory for both Extra Ball Lamp Memory only Targets 1-5 Memory only 03 = No memory
| 36 | Extra Ball Difficulty Control 00(Liberal)-09(Conservative) | 6 | 03 | |
| 37 | | LLP BONUS: 00 = No Memory | 01 = Memory | 7 | 00 |
| 38 | | Not Used | 00 | ||
| 39 | | Background and Attract Mode Sound Control | 00 |
Background & Attract Mode Attract Mode Only Background Only 03 = No sound
| 40 | High Score Credits | 1,2 | 03, |
| 41 | | Maximum Extra Balls at one time (00=No extra balts) | : | 04 |
NOTES: *
ol
7.
LLP = Lower Level Playfield
Second Factory Setting value is with jumper W25 on CPU Board connected. Description in brackets shown in Player 2 Display. Function 13 may be set to any multiple of 100,000 points. With Function 40 set to zero and Function 13 set to any score but zero, the High Score to Date feature operates but no credits are awarded. Although credits may be awarded for Replay scores (Functions 14-17) itis not recommended. Three credits are awarded for High Score to Date (Function 40). Change Function 26 to 00 to award Match credits. Setting Maximum Credits (Function 18) to zero places the game in a free play mode. With Function 19 set to 00, Functions 20-25 must be set manually. Refer to Table 3 for 8 standard pricing schemes (selected by values of 01-08 for Function 19) and custom pricing values. A“NO SCORE FLIPPER SERVE” is when a ball is ejected into play and no poiats are scored before the ball retums to the outhole, Spinner ramp shot to Ramp Chamber lights Bull's-Eye target fer Extra Ball with Ramp Chamber values needed shown below: 00=5K (1 completion of targets 1-5), 01=10K, 02 08=45K, and 09=5OK (10 completions of targets 1-5). LLP Bonus always reset when collected for 80,000.
ULP = Upper Level Playfield
5K, 03~20K, 04=25K, 05=30K, 06=35K, 07=40K,
GAME ADJUSTMENT PROCEDURE (Functions 13-41) Coin door must be open to change settings. 1, Set AUTO-UP/MANUAL-DOWN switch to AUTO-UP and depress the ADVANCE pushbutton. Test 04 is indicated in the Credits display, Function 00 in Match display, and game identification in Player | display.
- To raise Function number in Match display, operate ADVANCE pushbutton with switch set to AUTO-UP. To lower Function number, operate ADVANCE with switch set to MANUAL-DOWN.
- With desired Function indicated in Match display, raise value in player | display by operating credit button with switch set to AUTO-UP; lower value by operating credit button with switch set to MANUAL-DOWN. Value left in Player | display is the new setting. For values see Table 2, and for pricing Table 3. . Repeat steps 2 and 3 until all required adjustments have been made.
- Operate ADVANCE until Function 50 is indicated in Match display. From Function 50 you can return to game over or restore factory settings. Perform step 6 or 7 as desired.
- To return to game over, depress ADVANCE with switch set to AUTO-UP.
- To restore factory settings and zero audit totals: a, Operate Credit button with switch set to AUTO-UP until 45 is indicated in Player | Display. b. Depress ADVANCE. The game returns to Test 04, Function 00. c. Set switch to MANUAL-DOWN and depress ADVANCE to indicate Function 50. d. Set switch to AUTO-UP and depress ADVANCE.
RESETTING HIGH SCORE TO DATE
- Using game adjustment procedure, set Function 13 to the desired reset value.
- Depress HIGH SCORE RESET pushbutton.
FACTORY AUDIT TOTALS (Functions 42-49) The factory audit functions are not assigned.
GRN-GRY GRN-VIO GRN-BLU
232-1
232-2
a4
232-3 si Right ULP (10)
Lane Change |
Ramp Chamber
GRN-BLK
2J2-5
Jet Bumper
ULP
(lit value),
f Ube
Center Left
Standup Swit, ULP (10) it, Front Panel Front Panel (lt value),
t 000/ Tk Extra Ball when lit) LLP 25
ed Lane A (1000 wit, 100 winot It), ULP ‘Spinner a cor} a Rollover, ULP (1000) ULP (1000) 0 Standup Target, uLP "AoG0) a Fs Fd Butts. (100/ Figure 5. Switch Matrix
GRN-ORN 2J2-7 LP 060) LLP (1060) 10 Standup UP (080) 4 Standup Target, Hg (1000), ULP (1000) 2 Standup £ ULP (1000) 9 Standup 1 Stand Target uULP
n So) ip i660) P Gobo) uP GRN-RED 232-8 Front Panel LLP) B Standup uP (oe 6 Standuy Te 7 ‘Standup Outhole/Eject,
GRN-BRN rt, Front Panel Reset, 2J2-9 High Score
INITIATING AUTO-CYCLE MODE
- Set AUTO-UP/MANUAL-DOWN switch to AUTO-UP and depress ADVANCE pushbutton. Test 04 is indicated in Credit display and Function 00 in Match Display.
- Set switch to MANUAL-DOWN and depress ADVANCE to indicate Function 50 in the Match Display.
- Set switch to AUTO-UP and operate Credit button to indicate 15 in Player 1 Display.
- Depress ADVANCE pushbutton to start Auto-Cycle mode. Each cycle of this mode sequences thru the Display Digits Test, Sound Test (00), Lamp Test (01), and Solenoid test (02). J To terminate the test and return to game over, turn the game OFF and back ON.
CPU BOARD SELF-TEST Depress the DIAGNOSTIC pushbutton on the left side of the CPU Board. The following indications are provided. With 0 indication the game returns to the game over mode. 0 - Test Passed 1- IC13 RAM Faulty 2 - IC16 RAM Faulty 3 - ICI7 ROM 2 Faulty 4 -1C17 ROM 2 Faulty 5 - IC20 ROM | Faulty
6 - ICI4 Game ROM I Faulty
7 - 1C26 Game ROM 0 Faulty 8 - ICI9 CMOS RAM or Memory Protect Circuit Faulty 9 - Coin-door closed, Memory Protect Circuit Faulty, or IC19 CMOS RAM Faulty.
SOUND BOARD SELF-TEST Depress DIAGNOSTIC pushbutton on the top of the Sound Board. Several electronic sounds should be produced. This sequence of sounds is repeated until the game is turned OFF and back ON.
€ BOOKKEEPING AND GAME EVALUATION (Functions 01-17) 1. Set AUTO-UP/MANUAL-DOWN switch to AUTO-UP and depress ADVANCE pushbutton. Test 04 is indicated in the credits display, Function 00 in Match display, and Game Identification in Player | display. Operate the ADVANCE pushbutton to display Functions 01 thru 04 on the Match display (See Table 1) and record the corresponding totals (number of coins and total paid credits) from the Player | display. (To review a total that has been advanced past, set switch to MANUAL-DOWN and operate the ADVANCE pushbutton). Operate the ADVANCE pushbutton to display Functions 05, 06, and 07 in the Match display and record the corresponding free credit totals from the Player 1 display. Operate the ADVANCE pushbutton to display Function 08 in the Match display. Total credits is indicated in the Player 1 display and total free credits in the Player 2 display. . Operate the ADVANCE pushbutton to display Function 09 thru 12 in the Match display and record the corresponding totals from the Player 1 display. Operate the ADVANCE pushbutton to display Functions 13 thru 17 in the Match display aud record the corresponding totals from the Player 2 display. With switch set to MANUAL-DOWN operate ADVANCE to display Function 50 in the Match Display. From Function 50 you can return to game over or zero audit totals and return to game over. Perform step 8.a. or 8.b. as desired. . a. To return to game over, set the switch to AUTO-UP and depress ADVANCE. b. Tozero audit totals and return to game over set switch to AUTO-UP, operate the credit button to display 35 in the Player 1 display, and depress ADVANCE.
Table 1. Audit Totals
DESCRIPTION
FUNCTION | PLAYER 1 PLAYER 2 00 | Game Identification (2502 1) — 01 | Coins, Left chute — (closest to coin door hinge) _— 02 | Coin, center chute _ 03 | Coin, right chute — 04 | Total Paid Credits =
| 05 | Special Credits | — |
06 | Replay Score Credits —
| 07 | Match Credits | — |
08 Total Credits Free Credits 09 | Total Extra Balls — 10 | Ball Time in Minutes _ 11 | Total Balls Played —
| 12 | Current High Score to Date | _ |
13 Backup High Score to Date High Score to Date Credits Awarded Times exceeded Times exceeded Times exceeded Times exceeded 14 Extra Ball 1 Score 15 | Extra Ball 2 Score 16 Extra Ball 3 Score 17 Extra Ball 4 Score
GAME START . A ball should be on both the ULP and LLP. With credits posted press 1- or 2-Player Start. The number of credits displayed is reduced appropriately, player 1 display flashes, player 2 display counts down from “50” and a ball is served into play on the ULP. This ball should be caught with a flipper and sent into play. The game program can be set to serve a no-score ball a specific number of times. If, after this number of serves, player has not yet scored points, the ball in play is considered “drained”. With only one player, the player 2 score display counts down from “30” in between subsequent balls. When two play, the other player score display counts down from “50” between turns. Completing targets 1-2-3-4-5 lights the spinner ramp chamber. Making the chamber when lit for 5,000 or more holds the ULP ball in the chamber and the other ball is ejected onto the LLP. When the LLP ball drains, the ULP ball is kicked onto the ULP to continue play.
UPPER LEVEL PLAYFIELD Bonus Advance Targets 1-2-3-4-5 and V-A-R advances the bonus. Completing K-O-N advances the bonus multiplier 2X-3X- SX-10X.
Targets 1-2-3-4-5 Completing targets lights points for 1,000, Bull’s-Eye for 25,000, and advances lighting of ramp chamber value from 5,000 to 50,000.
V-A-R Rollovers Completing V-A-R advances jet bumper value 30-300-3,000.
Lane Change™ Feature The V-A-R and K-O-N lamps can be rotated by pushing the Lane Change button on the control panel.
Extra Ball Lighting the ramp chamber for 20,000* or more and then making the chamber lights the Bull’s-Eye target for a possible Extra Ball. Extra Balls, up to 4* at one time, are also earned by exceeding adjustable score levels.
LOWER LEVEL PLAYFIELD Bonus Advance Completing targets 6-7-8-9-10 collects and advances the bonus (20-40-60-80 thousand). Making A and B targets advance the bonus multiplier (2X-3X-4X-5X).
Special Topping out the bonus at 80,000 and the multiplier at 5X scores a special 50,000 points.*
TILT Ball in play is tilted on third* closure of Plumb Bob and playfield tilts. A single slam tilt returns game to Game. Over mode.
MATCH Match digits appear* in Ball-in-Play display and Game Over lamps go off: game then enters attract mode.
*Indicates game program adjustable features. s
§ “Warning: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference, Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”
ffs Wiliams Ww) 16-512-103 ELECTRONICS, INC. Game No. 512 September, 1982
VARKON
INSTRUCTION BOOKLET
This booklet provides game operation, bookkeeping, game adjustment, diagnostic, and self-test procedures for VARKON. For installation and special maintenance information refer to the blue-covered game manual,
SPECIAL CONSIDERATIONS WHEN REPLACING CIRCUIT BOARDS CPU Board
- Revision level 7 CPU Boards (batteries located on lower left corner at board) of later boards must be used.
- Must be equipped with blue-labeled Flipper ROMs and blue-labeled Game ROMs.
- Jumpers W3, WI0, WIL, W14, WI7, W19, W20, and W22 must be connected. Jumpers W4, W9, W12, WIS, W16, W18, W21, and W23 must be removed. With the exception of W25, (Factory Setting Jumper) all other jumpers are not changed. Driver Board Must be equipped with zero-ohm resistors or wire jumpers (W9-W16) in place of switch matrix drive series resistors R204-R211. Sound Board Must be jumpered for ROM operation and be equipped with Sound ROM 10. Jumpers W2, W5, W7, W9, WI1O, WI2, and WIS connected; W3, W4, W6, W8, WII, and W13 removed). Power Supply Board
- Model D 8345 board required (equipped with relay).
- Fuse F4 (10A SB) for flipper solenoids must be installed. Display Boards Model C 8363 Master Display and 7-digit Slave Displays required
Game Operation
GAME OVER MODE Turn game ON, player I display shows High Score to Date and Game Over lights come on. The High Score to Date alternates between player I and player 2 displays, and all playfield lamps on both Lower Level Playfield (LLP) and Upper Level Playfield (ULP) cycle in Attract mode.
CREDIT POSTING Insert coins; sound produced, number of credits displayed. If maximum credits* level is exceeded by coin or High Score to Date, credits are posted correctly and coin lockout de-energizes until remaining credits are below maximum. No credits may be won, and coins are rejected while coin lockout is de-energized. With | credit posted single player play is possible. With 2 or more credits posted, two player play is possible, or a single player can play more than one game.
Lane Change is a trademark of Williams Electronics, Inc.