CATHODE RAY TOMES

Ocean Hunter

The Ocean Hunter: The Seven Seas Adventure (Sega, 1998) · Manual · 91 pages · 82 sections · original scan

Page 1

DLX VERSION

OWNER’S MANUAL

SEGA ENTERPRISES, INC. USA

MANUAL NO. 4201-6419-01

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

VISIT OUR WEBSITE!

F come eo r Si FEA LE

7 a cnet ETRE et Ses care

ee

Page 4

SEGA

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 650-802-1750 phone 650-802-1754 fax

Page 5

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONS

  • NAME OF PARTS . ACCESSORIES . ASSEMBLY AND INSTALLATION . PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE . CONTENTS OF GAME . EXPLANATION OF TEST AND DATA DISPLAY 6-1 SWITCH UNIT AND COIN METER 2 TEST MODE 3 MEMORY TEST 4 INPUT TEST 5 OUTPUT TEST 6 SOUND TEST AnNRwWN

‘7 BOUNDRY SCAN TEST VOLUME ADJUSTMENTS 9 C.R.T. TEST 10 GAME ASSIGNMENTS -11 COIN ASSIGNMENTS -12 BOOKKEEPING -13 BACKUP DATA CLEAR TROL MECHA -1 ADJUSTING/REPLACING THE SWING (YAW) VOLUME -2 ADJUSTING/REPLACING THE PITCH VOLUME -3 REPLACING THE SPRING -4 REPLACING THE SWITCH 7-5 GREASING

  • COIN SELECTOR
  • PROJECTOR 9-1 CLEANING THE SCREEN 9-2 HITACHI MONITOR 9-3 MITSUBISHI MONITOR
  • REPLACEMENT OF FLUORESCENT LAMP. 10-1 REPLACEMENT OF FLUORESCENT LAMP. 10-2 REPLACEMENT OF LAMPS
  • PERIODIC INSPECTION TABLE
  • TROUBLESHOOTING
  • GAME BOARD 13-1 REMOVING THE GAME BOARD 13-2 COMPOSITION OF THE GAME BOARD
  • DESIGN RELATED PARTS
  • PARTS LIST
  • WIRING DIAGRAMS
  • CO. aaa aIZanaanaaaaaaaga
Page 6

SPECIFICATIONS

Installation space: 89 in.(D) x 45 in.(W)

Height: 82 in.

Weight: Approx. 820 lbs.

Power maximum current: 5.2 Amps (AC 120V 60 Hz AREA)

MONITOR: 50” PROJECTION DISPLAY

L

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to the THE OCEAN HUNTER DLX, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 650-802-1750 Fax 650-802-1754 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 7

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. Tf you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 8

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below:

  • Places subject to rain/water leakage, or condensation due to humidity;
  • In close proximity to a potential wet area;
  • Locations receiving direct sunlight;
  • Places close to heating units or hot air; ¢In the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
  • Places subject to any type of violent impact;
  • Dusty places.

INSTALLATION PRECAUTIONS

  • Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.
  • Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.
  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H).
  • For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

SK92 ®

AMUSEMENT MACHINE

Page 9
  • NAME OF PARTS

COIN CHUTE DOOR CONTROLLER

CASHBOX DOOR

SEAT & BASE CONTROL PANEL

ASSY TUBE AC_UNIT

CONTROL CABINET

GAME SPECIFICATIONS WIDTH HEIGHT DEPTH WEIGHT

all measurements are rounded up to the nearest 0.5”

PTV45”xX68”x22”~210 LBS.
BILLBOARD45”x16”x16”~50 LBS.
CONTROL CABINET39.5”xX44.5”x35.5”~400 LBS.
SEAT AND BASE39.5”x21”Xx24”~140 LBS.
WHEN ASSEMBLED45”x82”x89”~820 LBS.
Page 10
  • ACCESSORIES

DESCRIPTION Part No. (Qty.)

Note OWNERS MANUAL 4201-6419-01 (1)

Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.

CARTON BOX 601-8928 (2) Used for transporting the Game Board. Refer to Next Page. KEY MASTER KEY 220-5576 (2) (2) For opening/closing the doors For the CASHBOX DOOR

r

AC Cable (Power Cord)

600-6695 600-6695-01 (1) for USA

Used for installation TAMPERPROOF WRENCH M4 540-0006-01 (1) TOOL

TOSHIBA MITSUBISHI Remote Control for Projector Used for adjustment.

200-5536 (1) 200-5532(1)

One of the above 3 types of Remote Controls is used for the Projector. Remote Control for Projector Used for adjustment. HITACHI Remote Control for Projector Used for adjustment.

200-5410(1)

Page 11

THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE

WARNING! FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2 HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, THE OCEAN HUNTER

'INEVER SHIP MODEL 3 GAME BOARDS

OUTSIDE OF CAGE!!

CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM W Gl WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

Page 12
  • ASSEMBLING PRECAUTIONS

AN

WARNING Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 4-item sequence:

1 | ASSEMBLING OF THE PTV

JOINING CONTROL CABINET AND SEAT & BASE

WIRING CONNECTION BETWEEN PTV AND CABINETS

SECURING IN PLACE

POWER SUPPLY DH] | ms} | BY] | Ww] ] Nh

ASSEMBLY CHECK

Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.
Page 13

1 ASSEMBLING OF PTV

@ By using the specified screws, secure the 2 Mask Holders to the Projection Display Ceiling.

@ Insert the TV Mask from the underside as shown and secure with the total of 6 screws in the manner to sandwich the LOCK BRACKET as shown.

@ Secure the two Guide Brackets to the front of the Projection Display in the correct installation direction shown, by using 2 screws for each bracket.

@ Insert the Billboard’s 2 Connectors into the front as shown and secure with 2 screws.

@BILLBOARD SCREW (2), M516

g

@BILLBOARD’ s connector

PROJECTION DISPLAY Q@MASK HOLDER (2) FLAT HEAD SCREW(2) for each, M414 @GUIDE BRACKET a , MX 16, w/flat & spring washers

@SCREW (2) M5 X 25

iA) One each on both sides

+ _@LOCK BRACKET

@TV MASK g SCREW (4),M5X20, using flat wash asher ° @GUIDE BRACKET W(2), MS X16, w/flat & spring washers

Page 14

2 JOINING CONTROL CABINET AND SEAT & BASE

A During assembling work, the cabinet is moved. When assembling, ensure

WARNING! that casters of each cabinet are in contact with the floor.

@_ Connect the Seat & Base connector to the Control Panel connector.

@ Install the 2 Joint Brackets to the Seat & Base and the Control Cabinet by securing with 4 Hexagon Bolts for each Joint Bracket.

CONTROL CABINET.

SEAT & BASE JOINT BRACKET / \ HEXAGON BOLT (4), chrome, M820, w/flat and spring washers

Page 15

3 WIRING CONNECTIONS BETWEEN PTV AND CABINETS

Be sure to connect connectors securely. Incomplete connector connection can cause electric shock accident. Use car so as not to damage wirings. Dmaged wiring canc ause electric shock or short circuit accident.

Install the ASSY TUBE to each cabinet joined as per [2] on the previous page. and perform wiring connection on PTV.

FERRITE CORE

SCREW (2)black M4X8, w/flat and spring washers

SCREW (black) M4x8, w/flat & spring washers / Secure with [Plastic Tie Belt.

Page 16

@ Take out the 2 screws and unlock the Service Door to remove it from the front of the PTV.

@® Take out the 2 screws and unlock the Back Lid of Control Cabinet and remove the Back Lid.

@ Insert ASSY TUBE wires in the square hole beside the PTV’s Front Door and connect all of the wiring connectors. At aa this time, be sure to connect the connec- sy, tor to the corresponding one which has ‘ an identical color and number of pins. BACK LD

@® Secure the ASSY TUBE box part with 4 screws. At this time, use care so that the wires are not caught and damaged. Reinstall the Service Door.

ASSY THLE

Page 17
  • Pass the ASSY TUBE wire to the square hole at the lower of Control Cabinet, install 2 Ferrite Covers to the bottom of cable, and secure with Plastic Tie Belt.

© Insert the cable forementioned in #5 above to the top of the Filter Board and secure with the

screws.

@ Connect the remaining connectors, and install ASSY TUBE box part to the Control Cabinet with 2 screws. At this time, use care so that the wiring will not be caught and damaged.

Reinstall the Back Lid.

FERRITE CORE

SCREW (2) black MAx8, #/Flat and spring washers

SCREW (hiack) TOMO, w/Elat & Secure with : spring washers f Plastic Tie Belt,

Page 18

4 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the floor surface. Unless the Adjusters come into contact with the surface, the Cabinet can move of itself, causing an accident.

This machine has 12 each of casters and adjuster (See Below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately Smm. from the floor and make sure that the machine position is level.

ADJUSTER

@ Move the machine to the installation

position.

Q) Cause all of the leg adjusters to make | 7 contact with the floor. By using a wrench, make adjustments in the height L i of the leg adjusters to ensure that the machine's position is level. aol

=

@ After making adjustments, fasten the ° =

leg adjuster nut upward and secure the height of the leg adjuster. CASTER

it i T

Page 19

5 | power supply

WARNING @ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering.

The AC unit is mounted on the left side of Front Cabinet DX. The AC Unit incorporates the Main SW. Firmly ON. insert the Power Plug into the Socket Outlet. Turn the Main SW ON to turn power

(Ensure that the Main SW is OFF.

(Ensure that the Main SW is OFF (2) The AC unit is located on the left

side of the Cabinet. The Ac unit — incorporates the Main SW, and —S power coi rd. EARTH TERMINAL

® 7 C) Main SW off INLET

To the Power Supply ¥| Socket outlet (Gn Ci CLE &

MAIN SW CIRCUIT PROTECTOR AC Cable (Power Cord)

CAUTIONS TO BE HEEDED WHEN TURNING THE POWER ON

WARNING! First make sure that no one is in the periphery of the bike body and turn the Main SW on. When the power is turned on, the bike body motion starts automatically. The presence of a person(s) in the periphery of the bike can cause an accident. Turning the AC Unit’s Main SW on will cause the machine to start the POWER ON check automatically. In the POWER ON check, the bike body banks left and right, then returns to the centering position and stops. During this check, do not touch the bike body. If you do, the body reaction (at the time course-out or crashing) can not be obtained correctly. The Advertise mode is displayed at the same time the checking is finished. An ERROR display is indicated if irregularity is found in the POWER ON check. In case of an irregular reaction during game, turn power off and turn it back on again to finish the POWER ON check.
Page 20

ASSEMBLING CHECK

In the TEST MODE, ensure that the assembly has been made correctly and IC BD is satisfactory (refer to Section 6). In the test mode, perform the following test:

  • SOUND TEST

SOUND TEST

SELECT WITH ICE BUTTON AND PRESS BUTTON

  • C.R.T. TEST

c.R.T. TEST PAGE 1/2

15 31

RED

GREEN

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE

c.R. 7. TEST PAGE 2/2

i | PRESS TEST BUTTON TO EXIT Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

Page 21

VIDEO BOARD RAM TFST

GooD

PRESS TEST BUTTON TO FXIT

  • INPUT TEST

INPUT TEST

VOLUME TF FilcH a6 vOrUMI TP YAW vo VOLUME 2P PITCH G0 VOLUME 2P YAW oa

1P LEFT SHOT OFF IP RIGHT HOT OFF Pho riit gna al 2P HIGHT SHOT OFF

leo Stan vl 2Y STARI OFF

COIN #1 ot

SERVICE OFF TEST OFF

VHLSS SERVICE+TEST BUTTON TO EXIT

() OUTPUT TES

Quary) 10g)

iP START LAMP OFF PP STAHT TAME oll 1h GONTROLLLR REACTION OFF ZP CONTROLLER REACTION OFF

"LAUT

SELEG? WHIT BERVIGE BUTTON AND FRESS TEST BUTTON Selecting the INPUT TEST on the test mode menu screen causes the screen (on which each

switch is tested) to be displayed. Press each switch. For the coin switch test, insert a coin

into the coin inlet with the coin chute door

being open. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD

and wiring connections are tested, to be displayed. be sure to check if the sound is satisfactorily emitted from each of speaker and the sound volume is appropriate.

Page 22
  • SOUND TEST

SOUND TEST

AoM ano SF ano

SFxIT

SELECT WITH SERVICE BUITON AND FHESS [EST BUTTON

  • CRT. TEST
  • ——“ GR T. TEST PAGE 1/2 Q 18 al

GREEN

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE

GR, 7, TEST PAGE 22

PRESS TEST BUTTON TQ EXIT LI In the TEST mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Be sure to check if the sound is satisfactorily emitted from each speaker and the sound volume is approprate.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the monitor by refering to Section 9.

Page 23
  • PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

@ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is inserted can damage the power cord and cause a fire or electric shock. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. @ When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

WARNING!

Since this machine is a heavy structure of approximately 1000+lbs. its leg adjusters should be retracted when moving the machine over the floor. When moving the machine on the floor with slanted sur-

CAUTION! |I faces or step like differences, ensure that the PTV, Front Cabinet and Rear Base are seperated. Lifting the Cabinet with those items as is joined can cause the joint portions to be damaged.

Do not push the PTV from the rear side. Pushing the PTV from the rear side can cause the PTV to fall down. Push it from the side.

Page 24
  • CONTENTS OF GAME

AMMUNITION: The number of ammo that can be fired is displayed. Consecutive shooting is possible up to 5 rounds of ammo. The ammunition is replenished immediately after firing. The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.

Insert a coin(s) to ahve the number of credits appear on the lower-part of the screen. When the number of creidts required for game stazrt is registered, the on-screen display changes to “PRESS START BUTTON” from “INSERT COIN(S)” and both START BUTTONS flash. Up to 9 credits can be counted at a time. Coins inserted after counting 9 credits will niether be counted nor returned.

Which one of the Seat positions you play depends on which start button you pressed.

When the game starts, the name of the Ocean in the first stage and the prize advetrisement by the BOSS are displayed and the n the opening demo starts. THese can be skipped by pressing the start button. The opening demo is followed by the game mode in which you keep shooting the enemy characters.

GAME MODE

@

i)

0)

@

© LIFE: When LIFE becomes 0, the game is over,

By sighting the Gun Controller directly at the target, shoot down the sharks and other enemy characters coming at you and protect yourself from damage.

Use both Triggers (right/left) simultaneously to shoot 5 rounds (automatically) During this time, the SIGHT display disappears.

Earn ponts by shooting sharks, sea snakes, and other small itmes. The total points are displayed on the score display screen after finishing the stage.

Tf you shoot the Diver appearing during Game Play by mistake, “MISS SHOT” will be displayed on and you will lose one LIFE.

When the LIFE becomes 0, game is over. To continue, insert a continue play worth of coins and press the START BUTTON. In case a sufficient number of credits still remains, press the START BUTTON to continue.

Page 25

® The BOSS appears at the end of the stage. Shooting down the BOSS resuolts ina stage clear. On the top of the screen, the LIFE GUAGE(s) is displayed for the BOSS and or the LARGE SIZE ENEMY (middle boss) appearing during the stage. Every time you hit them, the corresponding LIFE GUAGE meter decreases. The enemy is shot down completely if the LIFE GUAGE meter diminishes to 0. NOTE that almost all the BOSSes and middel bosses have their weak points. Shoot the weak points on the screen to decrease the LIFE GUAGE meter quickly and increase the score at the same time.

() When the fight with the BOSS climaxes, the “SHOOT” mark will be displayed on the weak point of BOSS. At this point of stage, shooting elsewhere other than the weak point can not give damage to BOSS. Shoot the “SHOOT” point 3 times so as to down the BOSS (except for the 6th Stage).

@ This game allows 2 persons to play simultaneously. WHile one person is playing, the other person can participate in the game anytime by inserting a coin(s) and pressing the START BUTTON.

When all of the 7 Stages are cleared, if your score(place) is 10th or higher, you can enter your name. The name entered and the score are displayed by the on-screen ranking.

ADVICE ON PLAY

RESCUE THE DIVER Several times during play, you will encounter the Diver asking for Help. Quickly shoot down the enemy coming at the diver, and the diver will recover you life by one as thanks.

KEEP SHOOTING THE TREASURE CHEST In each stage, several Treasure Chests are provided in sunken ships, etc. When you hit the Treasure Chest, the lid opens and gold coins will scatter. However, you can earn only G100 points by shooting once. THe ammunition you fire the more ponts that the Treasure Chest allows you to earn. Let’s keep shooting at it.

Page 26
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

TABLE6 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

When the machine is installed, perform the following: INSTALLATION | |. Check to see that each setting is as per standard setting made 6-8, 6-9, OF MACHINE at the time of shipment. 6-10

  • In the INPUT TEST mode, check each SW and VR. 6-4
  • In the OUTPUT TEST mode, check each of lamps. 6-7
  • In the MEMORY TEST mode, check ICs on the IC Board. 6-3
MEMORYChoose MEMORY TEST in the MENU mode to allow the6-3

MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following:

SERVICING

  • MEMORY TEST 6-3
  • Ascertain each setting. 6-8,6 -9
  • In the INPUT TEST mode, test the CONTROL device 6-4
  • In the OUTPUT TEST mode, check each of the lamps. 6-7
CONTROL1. In the INPUT TEST mode, check each SW and VR.6-4

SYSTEM

  • Adjust or replace each SW and VR. 7

3 If the problem hasn’t been solved yet, check the CONTROL’s moves 7

PROJECTORIn the PROJECTOR ADJUSTMENT mode, check to see if the9

PROJECTOR adjustment is appropriately made.

IC BOARD1. MEMORY TEST6-3
  • In the SOUND TEST mode, check the sound related ROMs. 6-5
DATA CHECKCheck such data as game play time and histogram to adjust the6-11

difficulty level, ete

Page 27

CAUTIONS TO BE HEEDED WHEN USING THE TEST MODE

test mode causes the unit to perform the network check automatically. During this time, all of the linked units will not allow the game to be played in the normal status. Therefore, be sure not to enter the test mode if any one of the units is in

IMPORTANT! play. On the other hand, if even one unit is in the test mode, make sure that other machines are not in play. Gon In case where multiple units are linked for communication play, exiting from the

6 - 1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ If the COIN METER and the game board are electrically disconnected,

IMPORTANT! game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows:

SOUND VOLUME SPEAKER Controls the speaker volume ofall of the machines speakers.

@) SOUND VOLUME WOOFER TEST BUTTON

SERVICE BUTTON

Controls the speaker volume only for SEAT & BASE Woofer.

(3) TEST BUTTON (TEST SW)

For the handling of the TEST BUTTON, —SEEMER VOLE refer to the section on test mode. TEST COROUT PROTECTOR [e) LEFT GET

(4) SERVICE BUTTON

(SERVICESW) Gives credits without registering on the coin meter. CIRCUIT PROTECTOR FOR IP (left) CONTROLLER MOTOR CIRCUIT PROTECTOR FOR 2P (right) CONTROLLER MOTOR

Page 28

6-2 TEST MODE

In case settings are changed in GAME ASSIGNMENTS, COIN ASSIGNMENT the setting changes are not effective unless the test mode is exited and the game mode returns to the screen. The setting changes are ineffective if the power is turned off in the test mode. PORTANT!

The TEST MODE allows the functioning of each part of the Cabinet to be checked, the monitor to e adjusted, and the coins and game related various settings to be performed.

SELECTION OF TEST ITEMS

TEST MENU Press the TEST BUTTON to have the menu BouNoany scan rest displayed on the screen. ourpur Test Sound) Test Galt. Test . : : GAME ASS|GNMENTS Press the SERVICE BUTTON until the pointer is Volume absUSTMENT aw . BooKkeePING NS moved to the desired item to make a selection. BACKUP DATA CLEAR exit

SELECT WITH SERVICE BUTTON Bring the pointer to the desired item and press the St! Burton TEST BUTTON to enter the selected item’s test.

Page 29

6 -3 MEMORY TEST

CPU ROM TEST

GOOD (CROM13 MASK) IC. 5 XXXX 4 : GOOD (CROM12 MASK) 10. 6 XXXX The MEMORY TEST mode is for checking the GOOD (CROMI1 MASK) IC. 7 XXXX : : GOOD (CROMIG MASK} IC. 4 XXXX on-BD memory IC functioning. GOOD (CROM23 MASK} [C. 9 XXXx “, oa . “ 39 GOOD (CROM22 MASK) 10. 10 XXXX GOOD” is displayed for normal ICs and “BAD' GOOD (CROM21 MASK) 1C. 11 XXXX ca ee . GOOD (CROM20 MASK) 16.12 XXXX is displayed for abnormal ICs GOOD (CROM33 MASK) 1G. 430 XXXX GOOD (CROM32 MASK) 4C. 14 XXXX GOOD (CROM31 MASK) iC. 15 XXXX isc i Sop (GhOMs0 MASK] Kel 16 same @ When the test is completed, if the GOOD (CROM3 EPROM) IC. 17 XXXx i is 5 it is GOOD (CROM2 EPROM) IC. 18 XXXx display is as shown left, it is GOOD (CROMI EPROM) IC. 19 XXXX satisfactory. GOOD (CROMO EPROM) IC. 20 XXXx

PRESS TEST BUTTON TO CONTINUE woe : : @ After finishing the test, pressing the TEST BUTTON allows the

MENU MODE to return on the

screen.

VIDEO BOARD RAM TEST

GOOD

PRESS TEST BUTTON TO EXIT

—————_.__ ese VIDEO BOARD ROM TEST

GOOD (VROMO01) GOOD (VROMO 0) GOOD (VROMO3) GOOD (VROMO2) GOOD (VROMOS) GOOD (VROMO4) GOOD (VROMO7) GOOD (VROMOS) GOOD (VROM11)

Hl VIDEO BOARD RAM TEST

i i ' t i ‘ 600D (vROMIG) | t ' ' ' ' ' 600d

GOOD (VROM1 3)

GOOD (VROM1 2)

GOOD (VROM15) GOOD (VROM14) 600D (VROMI7) GOOD (VROMI6) PRESS TEST BUTTON TO EXIT 29 apooRNDDaDNADNDO BOW aan een—-owaum

PRESS TEST BUTTON TO CONTINUE

Page 30

6-4 INPUT TEST

When INPUT TEST is selected, the MONITOR will show the following, allowing you to watch the status of each switch. On the screen, periodically check the status of each switch.

INPUT

VOLUME 1P VOLUME 1P VOLUME 2P VOLUME 2P

Po LEFT P ORSGHT Pp P LEFT RIGHT

START START OFF

COIN #1 OFF COIN #2 OFF SERVICE OFF TEST OFF

PRESS SERVICE+TEST BUTTON TO EXIT

6-5 OUTPUT TEST

OUTPUT TEST

P START LAMP OFF P START LAMP OFF P CONTROLLER REACTION OFF P CONTROLLER REACTION OFF new

EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON @ By pressing each switch, if the display on the righthand side of the name of each switch changes to ON from OFF, the SW and the wiring connections are satisfactory.

@ Open the COIN CHUTE DOOR and insert a coin from the COIN ENRTY to check the COIN CHUTE SW.

In the INPUT test, pressing the TEST BUTTON causes the menu to return to the screen.

Choose OUTPUT TEST to have the MONI- TOR screen shown left to appear. This screen allows lamp status to be checked.Periodically check the lamp status in this mode.

Press the SERVICE BUTTON to move the arrow to the desired lamp test item.

Press the TEST BUTTON. If the display to the right of the lamp name changes to ON from OFF, the lamp and wiring connection are satisfactory.

Choose EXIT and press the TEST BUTTON to return to MENU mode (FIG. 6.2).

Page 31

6-6 SOUND TEST This enables sound used in the game to be checked. Sound related memory and each speaker are checked. SOUND TEST @ Press the SERVICE BUTTON to bring the Bom arrow to the desired sound item to be SE tested. Pressing the TEST BUTTON causes EXIT the desired sound test to appear. Each time the SERVICE BUTTON is pressed, the numeral displayed on the screen counts up and sound is emitted. eo eo

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Selecting BOUNDRY SCAN TEST, causes 6-7 BOUNDRY SCAN TEST the Game Board’s testing in terms of hardware to be performed automatically.

@ When the test is completed, if the results BOUNDARY SCAN TEST ee are shown as above it is satisfactory.

TOTAL ERRORS 0 @ After finishing the test, press the Test Button to have the Menu Mode return to the screen. Next, turn the power off and then turn it back on again. By doing so, the Board initialization is performed to avoid malfunctioning. PRESS TEST BUTTON TO EXIT

6-8 VOLUME ADJUSTMENTS This item allows the Volume Value to be

adjusted after the replacement of Controller Volume or when the Controller movements VOLUME ADJUSTMENTS are irregular.

TP PITCH MIN (ba)MAX (60)NOW (86)..
RE EAYe, Win G8Mae Glnow fen@Set an appropriate Volume Value by moving
ze YAMMIN 40)MAX (bhOPNOW {88}the Controller up/down and right/left fully

EXIT WITH SAVE within the moveable range. = Ex Ir WETHOUT “BAVE Move the Cursor to EXIT WITH SAVE and press the test buton to store the setting contents and return to the Menu Mode. To SELECT WITH SERVICE BUTTON ’ : AND PRESS TEST BUTTON return to the Menu Mode without changing the setting contents, move the Curso to EXIT WITHOUT SAVE and press the TEST BUTTON.

Page 32

6-9 C.R.T. TEST

r \ CRT. TEST 1/2

PRESS TEST BUTTON TO CONTINUE

TTT GRIT TEST 2/2

PREGS TEST BUTTON 10 EXIT ni rarnrer ewe Select C.R.T. TEST to cause the MONITOR to display the screen shown left, allowing MONI- TOR adjustment status to be checked.

Periodically check the MONITOR adjustment status on this screen.

The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i.e.,red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right.

Press the TEST BUTTON to shift to the next page (2/2).

The screen (2/2) allows screen size and distortion to be tested.

Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted.

Press the TEST BUTTON to return to the MENU mode.

Page 33

6 - 10 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

s PORTANT! Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EXIT.

qd) Press the SERVICE BUTTON to move the arrow to the desired item.

  • Choose the desired setting change item by using the TEST BUTTON.

@ To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

GAME ASSIGNMENTS @ GAME DIFFICULTY counTRY EXPORT . paFeueuLTY NORMAL This game allows by-course difficulty level to be eeinee EyEes er set in 4 levels. Depending on the difficulty level CONTROLLER REACTION NORMAL = EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON set, the intial time varies.

@ ADVERTISE SOUND Setting of sound during Advertise. ON(sound to be emitted), OFF(sound not to be emitted).

@ CABINET TYPE Setting of cabinet. Set to DELUXE for this machine.

@ CONTROLLER REACTION These FIGURES/ Sets the Controller’s vibration strength and off for TABLES show the no vibration. factory recommended settings. @ counTRY Message language.

Page 34

6-11 COIN ASSIGNMENTS

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SET TING CHANGE PROCEDURE

Gro Setting changes cannot be stored unless the TEST BUTTON is pressed

PORTANT!

©

@

©) while the arrow is on EXIT.

Press the SERVICE BUTTON to move the arrow to the desired item.

Choose the desired setting change item by using the TEST BUTTON.

To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

@ COIN CHUTE TYPE Sets the combination of the number of COIN COIN ASSIGNMENTS CHUTEs and the number of players as appli- 2CREDITS TO START 1CREDIT TO CONTINUE cable. In the case that the COIN CHUTE is CoN CRED, gvaring *1 changed, be sure the setting is made in a manner aa meeting the replaced coin chute. coin cure #2 i COIN” 1 CREDIT COMMON: MANUAL SETTING Coins are accepted in common for both players.

  • exit SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON INDIVIDUAL: Each player uses a coin chute which accepts coins independently.

@ CREDIT TO START Number of credits required for starting game (1~5 credits are selected.)

@ CREDIT TO CONTINUE Number of credits required for continuing game (1~5 credits are selected.)

@ COIN/CREDIT SETTING Sets the CREDITS increase increment per coin insertion. There are 27 setings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 6.10a, 6.10b) #27 refers to FREE PLAY. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 6.10b.

@ MANUAL SETTING This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/CREDIT SETTING (refer to TABLE 6.10c).

Page 35

TABLE 6.11a COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

SETTING FUNCTIONING OF CHUTE#1

SETTING #11 COIN1 CREDIT
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #5,1 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT
SETTING #131 COIN1 CREDIT
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT.
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN6 CREDITS

SETTING #27 FREE PLAY

Page 36

TABLE 6.11b COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE)

SETTING FUNCTIONING OF COIN CHUTE

SETTING #11 COIN1 CREDIT
SETTING #61 COIN2 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #173 COINS1 CREDIT
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #215 COINS1 CREDIT
SETTING #223 COINS1 CREDIT

5 COINS 2 CREDITS

SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS SETTING #27 FREE PLAY

Page 37

MANUAL SETTING

MANUAL SETTING

>EXIT

Ne SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

1 CREDIT COIN TO CREDIT 1. COIN

BONUS ADDER NO BONUS ADDER

COIN CHUTE #1 MULTIPLIER

L.COIN COUNTS AS 1 COIN

CON1234567
cReDIT1002003045SGT

COIN CHUTE #2 MULTIPLIER I. COIN COUNTS AS 1 COIN

COIN1234567
cREDIT102003045SGT

FIG. 6.11b MANUAL SETTING

@ Determines Coin/Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin. Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen. ~\

@ This sets how many tokens one coin represents.

Table 6.11lc MANUAL SETTING

COIN TO CREDIT 1 COIN1 CREDIT 2 COINS 1 CREDIT. 3 COINS 1 CREDIT. 4 COINS 1 CREDIT. 5 COINS 1 CREDIT. 6 COINS 1 CREDIT. 7 COINS 1 CREDIT. 8 COINS 1 CREDIT. 9 COINS 1 CREDIT.

BONUS ADDER NO BONUS ADDER 2 COINS GIVE 1 EXTRA COIN 3 COINS GIVE | EXTRA COIN 4 COINS GIVE 1 EXTRA COIN 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE | EXTRA COIN 7 COINS GIVE I EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

COIN CHUTE MULTIPLIER 1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 38

6 - 12 BOOKKEEPING

Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2.

BOOKKEEPING PAGE 172

COIN REPORT

GOIN ChUTE #1 COIN CHUTE #2 TOTAL COINS coin CREDITS SERVICE CREDITS TOTAL GREDITS

NUMBER OF GAMES °

ToTAL PLAY AVERAGE PLAY TIME LONGEST PLAY TIME SHORTEST PLAY TIME TIME oD TIME a oH om os oH om os OHooMooS oHoaMmoOs oHoomo0S

PRESS TEST BUTTON TO CONTINUE

BOOKKEEPING PAGE 2/2

TIME HISTOGRAM

oMoos ~ omzes 0 Omz05 ~ OM59S ° TMOOS ~ IM25S i 1M308 ~ IMBSS ° 2mo0s ~ 2Mz98 o 2M30S ~ IMSS 8 3M00S ~ 3M2a5 a BM30S ~ 3M59S 0 aMoos ~ 4MZ9S o 4M30S ~ 4MS95 9 SMOGS ~ §M29S a 5M30S ~ 5M5ES a émoos ~ 6Mz95s A SM30S ~ 6M5as 9 7M008 ~ 7295 9 7M308 ~ 7MS9S fa BMoos ~ sM295 ° BM30S ~ suSes Q 9M00S ~ $M295 fy aM30S ~ 9M59S 3 OVER 1 0MDa0S °

PRESS TEST BUTTON TO ExIT

6 - 13 BACKUP DATA CLEAR

BACKUP DATA CLEAR

YES (CLEAR ) ) = NO (CANCEL

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON COIN CHUTE#*:

Number of coins put in each Coin Chute.

TOTAL COINS:

Total number of activations of Coin Chutes.

COIN CREDITS:

Number of credits registered by inserting coins.

SERVICE CREDITS:

Credits registered by the SERVICE BUTTON.

TOTAL CREDITS:

Total number of credits (COIN CREDITS+SERVICE CREDITS).

TOTAL TIME:

The total energized time.

On page (2/2), each play frequency is displayed. When setting difficulty levels, the frequency can be reffered to as a standard.

When in the PAGE 2/2 mode, press the TEST

BUTTON to return to the MENU mode.

Clears the contents of BOOKKEEPING and high score player ranking entry. When clearing, bring the arrow to “YES” and when not clearing, to “NO”, by using the SER- VICE BUTTON, and push the TEST BUTTON. When the data has been cleared, “COMPLETED”

will be displayed. Bring the arrow to “NO” and press the TEST BUTTON to cause the MENU

mode to return on to the screen.

Note that the contents of the game setting and sighting adjustment are not affected by BACKUP DATA CLEAR operation.
Page 39
  • CONTROL MECHA
WARNING! Before starting to work, ensure that the power SW is OFF. Failure to observe this can cause electric shock and short circuit accident. Use care so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. Do not touch undesignated places. Touching places other than those specified can cause electric shock and short circuit accidents.

In the test mode, if the controller V.R. value movements are irregular, adjust or replace the V.R. in the following procedure.

7-1 ADJUSTING/REPLACING THE SWING (YAW) VOLUME

Take out the 4 screws and remove the PANEL LID LOWER

SCREW (4), black MAX, /Llat & spring washers flat washer used for the lower portion.

ADJUSTING THE VOLUME

@ In the Test Mode, have the Volume value indicating scren displayed.

@ Loosen the 2 screws which secure the Volume Bracket to disengage the gear mesh.

® Adjust the gear mesh in the manner so that the D-CUT face of volume shaft is in the status shown in the picture on right. when the controller is positioned strai;

Fasten the 2 screws and secure the Volume Bracket.

After adjustment, be sure to perform Volume Settings in “VOLUME ADJUSTMENTS” in the Test Mode. VOLUME hen) 5484

iol

  • nN

SCREW (2) NG a, w/flat and spring washers

Page 40

REPLACING THE VOLUME ® Turn the power off. @ Disconnect the connector.

  • Remove the Volume Bracket by taking out the 2 screws which secure the Volume Bracket. iO) Remove the Volume Gear from the Volume Shaft and replace the Volume. © After replacement, adjust the Volume as per the proceeding page.

7-2 ADJUSTING/REPLACING THE PITCH VOLUME

This work should be performed by the locations Maitenance Man or Service Man. Performing work by those who do not have the technical expertise can cause electric shock accident.

WARNING!

@ Take out one each of screw, remove Grup Lid (left/right), and disconnect the connector.

GRIP LID SCREW, one each, black 4 10, v/flal and spring vashers

TAMPERPROGE SCREW. 2 each Mo iD

@ Take out 2 cach of screws and pull out the GRIP (left/right). GRIP

Page 41

® Take out the 5 screws and remove the Controller Cover.

CONTROLLER COVER .

SCREW(S), chrome Mim, flal washer used, ~~,

ADJUSTING THE VOLUME

Oo) In the Test Mode, have the Volume

Value indicating screen displayed.

@) Loosen the 2 screws whihe secure the Volume Bracket to disengage gear mesh.

3S) Adjust gear mesh in a manner so that the

Volume Shaft D-CUT face is in the status shown at right, when the Controller position is level.

@) Fasten the 2 screws and secure the Volume Bracket.

©) After adjustment, be sure to perform Volume in “VOLUME ADJUST- MENTS” in the TEST Mode.

REPLACING THE VOLUME

Turn power off.

Disconnect the Connector. QOOCLO W-CUT PACE

FOLUME, . VOLUME BRACKET 220-3484 oe (PL;

O.® < fe SCREM (2), —_ 4 MAX, a/Tiat & spring washers

Remove the Volume Bracket by taking out the 2 screws which secure the Volume Bracket. Remove the Volume Gear fromt he Volume Shaft and replace the Volume. After replacement, adjsut the Volumeas per above the procedure

Page 42

7-3 REPLACING THE SPRING CONTROL VAN LoD)

® Take out the 2 screws and remove the Control Panel Lid. v i 2 pach’ Mix’. black

©® Take out a total of 8 screws

and remove the Control Panel Base. At this time, be careful of the wiring connectors.

Ubveseeoratuees Lie UU

Maec8, fiat washot nsed.

CONTROL PANKT. RAST

sewer (4), black “WOR, w/flat & spring washers”

® Replace the Spring.

SPRING oe OUN 205K

Page 43

7-4 REPLACING THE SWITCH

The Controller has some small parts. When dissassembling, be very careful so as not to lose parts.

WARNING!

When the Trigger SW is pushed, if the INPUT TEST screen does not display “ON”, the switch inside the GRIP may be malfunctioning and in this case, switch replacement is needed. TRUSS SOREN

oO) Remove the GRIP by first reffering to the

section on replacement/adjustment of pitch volume.

@ Remove the screw and disassemble the GRIP

. TRIGGER SW @) Replace the Switch. n-ne

Page 44

7-5 GREASING

AN

CAUTION! Do not touch places other than those specified. Touching places not specified can cause an electric shock or short circuit accident. Be sure to use the designated grease. Using undesiganted grease can cause parts damage. Do not apply greasing to undesignated places. Failure to observe this can cause malfunctioning or quality deterioration of parts.

Apply spray greasing once every 6 months to the 2 places shown in the figure below, where the spring and gear are engaged. For spray grease, use NOK KLUBER L60 or GREASE MATE.

VOLUME GEAR MESH PORTION PITCH VOLUME GEAR MESH PORTION |

RAIL PORTION

Page 45
  • COIN SELECTOR

HANDLING THE COIN JAM

to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: @) Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). @ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. (@ Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. © Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. ©) After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selecting,

IMPORTANT! Insert a regular coin in the normal

working status and ensure that the Selector correctly functions. ©

Insert a coin [

COIN INSERTION TEST while Keeping

Once a month, when performing the COIN SW Button pressed

TEST, simultaneously check the following: down and check if it is 1 Does the Coin Meter count satisfactorily? rejected. O Does the coin drop into the Cashbox correctly? COIN METER

O Is the coin rejected when inserted while keeping

the REJECT BUTTON pressed down? If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check

3S

\ CRADLE

FIG.8b

Page 46

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON THE OCEAN HUNTER COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 MARS 2000 SERIES (FORWARD-MOST POSITION)

HOLE POSITION#2 MARS 2000 SERIES DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 DsIO1*

*The back flange on the chute can be removed for hole position #4. If the flange is not removed, it may interfere with the back of the cabinent.

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls authorized distributors. The Part # is 91-4000-01. The Mars stacker can be obtained through an authorized Mars distributor.

Page 47

QO EIR CapNy et Tow T Rl A oa) red Wk HUARD 37... FLA CRIK TL Bia Cae) a ad

ASRS RITES Qo RATAN GREE AIAP TALE

Rat ner WHIRL

|e WA IU TAL Lr Ide) AL welll Fb Hb

CLE bi EAL fia

FUR ik UREPELIELY ARIAL Mae AYLI ah SAME EIT Be “ADA ANTI eB A AIT) THEN Edi STH BAL MLAs ETRY EL UR, ay UnesAIT TNL ELLTESITLS SESH.

CL THLaT Lat nt YAY TMT SHEL Theo ie sad day lat ii lt oF

(AR Kall Pe ee

ae 4 GTi + LOCKE USF Untlat Wht AY" ULE 1-0 a 2 ne eh elle,

FORM Re EMS Wa

Page 48
  • PROJECTOR

tion to its handling. When cleaning, freain from using water or volatile chemicals.

CAUTION! |] Since the Projector has been adjusted at the time of shipment, avoid making further adjustments without good reason. Since the projector screen is susceptible to damage, pay careful atten-

Fine adjustments are stored inthe Projector. Pressing the Fine Adjustment SW (Convergence Adjustment) results in entering the Fine Adjustment mode, and this may cause the stored fine adjustment to be changed. During work other than for adjustment, should you touch the Fine Adjustment SW by mistake, immediatley tren power off by using the main SW and then turn it back on again. If any distortion or color deviation is found in the test mode and adjustments are needed, use the specified Adjustment Knob, or perform the adjustment by remote control. Note that there are two PROJEC- TOR makes (HITACHI and MITSUBISHI) and the adjustment method is different between the two. When checking the Adjustment Control Knob, remove the PTV’s service door. For the HITACHI PROJECTOR, open the cover in front of the control panel. For the MITSUBISHI PROJECTOR, remove the cover.

tion caused by the geomagnitism at the installation location and peripheral magnetic field. After the installation of machine, and be-

CAUTION! fore commencing operation, check for Convergence deviation and if

deviated, make adjustments. The Projector is subject to color deviation due to Convergence devia-

9 - 1 CLEANING THE SCREEN

When the screen surface becomes dirty with dust, etc.., clean it by using a soft cloth such as gauze. When water and volatile chemicals such as benzene and thinnerspill onto the screen surface, it may be subject to damage, therefore, do not use them. Also, since the surfaces are susceptible to damage, refrain from rubbing with a hard material or using a duster.

Page 49

9-2 ADJUSTING HITACHI PROJECTORS

nN Never touch places other than those specified. Otherwise, hazardous

electric shock or short circuit can be caused.

CAUTION!

There are 2 types of HITACHI PROJECTORS. As shown below, the Control’s Panel’s layout differs from each other. The lower layout allows Static Convergence to be adjusted merely by operating the Remote Control.

0 HITACHI PROJECTOR CONTROL PANEL

POWER BUTTON (this does not function)

of » Gd

CONVERGENCE ADJUSTMENT SW

CAUTION! Do not touch the right-hand side switch.

CONVERGENCE ADJUSTMENT SW ® ® 6) 2) @

CAUTION! Do not touch the left-hand side switch.

pyNaMic stanic y A contrast Vv. Hou CONVERGENCE POSITION BRIGHT.

@ v.HOLD @ BRIGHT @ CONTRAST @H. POSITION

©® V. POSITION

Do not touch Dynamic Convergence Adjustment Switch. Although dynamic Convergence adjustment is not needed for this product, should it be pressed by error, turn power off and then turn it back

IMPORTANT! on again.

CROSS PATTERN Press the Static Convergence Adjustment SW which is on the Control Panel to cause the cross pattern to appear. Use the Remote control to make static adjustment. For the operation of the Remote Controller, refer to the following pages. Press the Static Convergence SW. At this time, static adjustment results ar ewritten and the PTV screen will return to the original screen code.

Page 50

In Case of Remote Controller (Part No. 200-5297):

REMOTE CONTROL Entering Projector's Convergence Adjustment Mode allows the Crosshatch ‘fo > to be displayed on the screen. At this time, if the horizontal and vertical Bs- lines (of the cross) are not blurred and displayed in white, the convergence = _7ue- status is correct. If red or blue color is blurred from the line, the conver- MATE eC hs gence is incorrect. In this case, make adjustment in the following Adjust- ( es |] es3|[ess ) ment Procedure to retum to the correct convergence status.

(es? [Tess [[es « )

(as 13 Twist

Eo = ve.

es Nes 1 ) sve lhe. EF (2 T nan

Q©O©068000 es 15] [rsa SN Cr (eer =

oO O®

Make sure that the slide portion of the Remote Control is positioned as per @) above. Press BS1. Position the slide portion of the Remote Control to @ in the above Figure. Press VIDEO 1. Position the Remote Control's slide portion to the above ) . Press " +" to have the cross pattern appear. Use the remote cotroller to make static adjustment. Remote control [ 2 ],[ 5 ].... Causes the red horizontal line to match with the green horizontal line. Remote control [ 4 ],[ 6 ] .... Causes the red vertical line to match with the green vertical line. Remote control [ 8 },[{11] .... Causes the blue horizontal line to match with the green horizontal line. Remote control [10], [12] .... Causes the blue vertical line to match with the green vertical line. Position the Remote Control's slide portion to @) in the above Figure and push "OFF" 5 times to return to the normal mode.

Page 51

In Case of Remote Controller (Part No. 200-5410):

If Convergence Adjustment is deviated, after the crosshatch pattern appears, the cross pattern will not be white, with red or blue color being blurred from the lines. In this case, move the red or blue line by operating the Remote Controller. When the line is superimposed on the reference line (green) to avoid blurring, the cross lines will become white.

@ Have the Remote Controller face the Projector screen and press Key 1, 2, and 3 (Portion @ shown) for Static Convergence Adjustment sequentially in order, causing the cross pattern to be displayed. @ Press the following arrow keys (Portion @ shown) to make adjustments. Cursor ¥ ...... Causes the red horizontal line to match with the green horizontal line. Cursor = ...... Causes the red vertical line to match with the green vertical line. Adjustment # ¥ Adjustment > @® Press the CANCEL Key (Portion ® shown) 5 times. This operation allows for returning to the original screen and at the same time storing the adjustment data. . Causes the Blue horizontal line to match with the green horizontal line. . Causes the Blue vertical line to match with the green vertical line.

Page 52

9-3 MITSUBISHI PROJECTOR

MITSUBISHI PROJECTOR CONTROL PANEL

®9O0OC0GGCO0000 POWER BUTTON

Convergence Adjustment SW

() v.Pos H.POS R-GAIN G-GAIN © B-GAIN

  • CONT BRI V.W (9) H.W RAL. Linearity adjustments in horizontal directions BHL. (red or blue) are made.

STATIC CONVERGENCE ADJUSTMENT

Convergence Adjustment SW (@® TEST ® re @< ®b OV @A @8 POWER Test mode on/off key

RIB key

Left shift key

Right shift key

Lower shift key

Upper shift key

Power button

@ For the Convergence adjustment mode, press the test mode on/off key. (©)

@ Ensure that “R” is displayed on the screen.

Make adjustments so as to cause the red cross pattern to match with the green cross

pattern by using Left shift key , Right shift key ©) , Lower shift key (16) sand

Upper shift key

By using R/B shift key

@ , cause the red adjustment “R” to shift to blue adjustment

“B” and make sure that “B” is displayed on the screen.

© In the same manner as in@) above, cause the blue cross pattern to match with the green cross pattern.

After making adjustment, press the test mode on/off key @ to cancel the convergence adjustment mode.

Page 53

STATIC CONVERGENCE ADJUSTMENT METHOD WITH REMOTE CONTROL,

@ Although Remote Control Buttons other than those specified below do not function even if pressed during Convergence Adjustment, do not press them during adjustment work so as to avoid causing malfunctioning. @ Operate the Remote Control towards the PTV screen. If directed other than to the PTV screen, the Remote Control does not function.

BEFORE USING REMOTE CONTROL: First make sure that the main SW on the Projector’s control panel is ON (the LED adjascent to the main SW is lit). The Remote Control has 2 different types. Depending on the type, the Adjustment procedure is different.

In case of REMOTE CONTROL (Part No. 200-5298): oO) For the Convergence Adjustment mode, press the test button. Ensure that “R” is displayed on the screen.

@ Make adjustment so as to cause the red cross pattern to match with the green cross pattern. When the red cross matches the green cross, the green cross turns yellow or white. -

Use remote control buttons shown below to move the red cross as follows:

Button © ——— to the left to the right Upward —— Downward Use Remote Control button(6) to shift “R” to “B”. Make sure that “B” is displayed on the screen. Each 1 . 5 _ 4 time Button © is pressed, red and blue adjustments are shifted.

® In the same manner as in(2)above, cause the blue

cross to match the green cross. When the blue cross Ne IO

matches the green cross, the green cross turns white. 2 . 3 4 <6) oO @ oO

® After adjustment is made, press the test button to Ong O

cancel the Convergence Adjustment mode. 0600 *When 2 minutes or more elapses in the Convergence mode screen without taking any action, the on-screen adjustment mode will disappear.

Page 54
  • REPLACEMENT OF FLUORESCENT LAMP AND LAMPS

() @ When performing the work, be sure to turn power off. Working with

power on can cause an electric shock or short circuit accident. The Flourescent Lamp, when it gets hot, can cause burns. Be very

WARNING! careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accident.

CAUTION!

10 - 1 REPLACING THE FLUORESCENT BULB

Remove the Billboard Holder and pull out the Billboard to replace the Fluorescent Lamp, and

Lamps. g

e g saw sce BILLBOARD HOLDER M4X8, chromeplated NN be

FLUORESCENT LAMP 30W

t} To slide

TAMPERPROOF_ SCREW (4)

“Wed, ae 10 - 2 REPLACING THE LAMPS

/ Remove the START SW PLATE ont op

of the Control Panel by taking off the 4 screws.

Pull the switch portion and pull to remove it

START SW PLATE

LAMP 5V_3W 390-5160

Page 55
  • PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation. When handling the controller, the player will be in direct contact with it. In order to always allow the player to enjoy the game, be sure to clean it regularly.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securley inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with dust as is accumulated can cause a fire or electrical shock. Periodically once a year, request the place of contact herin stated or the Distributer, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is

accumulated in the interior without cleaning can cause a fire or

accident. Note that cleaning the interior parts can be performed on a pay-basis.

in contact with the floor

ITEMS DESCRIPTION PERIOD REFERENCE

CONTROL MECHACheck Volume Value and SWas required
Grease to gear portionWeekly6

Check Adj. Gear engagement | Monthly 6

COIN SELECTORCheck COIN SW.Monthl6

COIN SELECTOR cleaning __| Trimonthly 8

PROJECTORSCREEN cleaningWeekly9
Check adjustmentsMonthly3,6,9
GAME BDSetting checkmonthly6
INTERIORCleaningAnnuallysee above.

POWER PLUG Inspection and cleaning

CABINET SURFACECleaningAs necessary | see below
CABINETEnsure that adjusters areAsnecessary | 3

CLEANING CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squezzed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Page 56
  • TROUBLESHOOTING Should trouble occur, first check connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation Power is not supplied.

Power supply/voltage is not correct.

AC main fuse causes the power to be cut off due to momentary overload. Plug in correctly

Make sure that power supply/voltage is

Check fuse. Remove the cause of overload and replace fuse

Irregular sound is emitted from the inside Rear Base. Poor mesh of mechanism gear inside Rear Base

Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Adjust gear mesh

Apply greasing or eliminate extraneous matter.

During game , no bike body reaction and irregular functioning. Game start does not unlock bike. POWER ON check is not satisfactory

Poor connection or malfunctioning of Motor driver and Drvie BD

Overheat of Motor 1> Redo power input and complete POWER 2> Perform drive BD test.

3> Check for connection between motor Motor driver, Driver Bd and Game BD. 4> Wait a while turn power back on.

The color of the image on PROJ. screen is incorrect. Connector connections are defective. Check the connection for the RGB and SYNC connectors of the PROJ. TERM. BD and VPM BUFFER BD.

screen has color deviation. The image on PROJ. Affected by the magnetic field of installation location. Make CONVERGENCE adjustment. (Refer to Section 9.)

No sound is emitted. Sound Volume adjustment is not appropriate.

Sound BD and speaker are malfunctioning. Adjust sound volume. (see Section 6).

Perform sound test to find and replace defective parts.(Refer to Section 6).

HANDLE MECHA and Bike Body not functioning corectly VR. deviation or malfunctioning Poor mesh of Adjust Gear Spring Fault in throttle /brake Perform VR. setting Adjust or replace V.R. Replace the Spring

The Fluorescent lamp does not light up. The Fluorescent tube is burnt out. Replace the Fluorescent tube (Refer to Section 10).

Bike Body is not locked. Wing Bolts for maintenance are not removed. Remove the Wing bolts.

Bike body centering incorrect. VR. setting fault VR. deviation or malfunctioning. Perform VR. setting Adjust or replace V.R.

Page 57
  • GAME BOARD
WARNING!
CAUTION! @ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at the time of shipment. The electronic parts on the IC Board could be damaged due to human static electricity.

13 - 1 GAME BOARD

@® When replacing or inspecting the Game BD, take out the Game BD by using the following procedure:

@ _ Turn the AC unit’s Main SW OFF.

@ _ Remove the 2 Truss screws (black) from the upper face of the Front Cabinet, unlock with the Master Key to open the Service Lid.

@® Take out the 2 screws shown to remove a total of 6 connectors.

Hold the catch of the Shield case Base and pull out upward.

® Take out the 3 screws to remove the Case Lid from the Shield Case. The Game Board can be viewed.

SHIELD CASE LID

WENG BOLT (2) MAx23, | flat & spring washers used.

SCREW {3} WaXs, g/tlal & spring washers.

Page 58

13 - 2 COMPOSITION OF GAME BOARD

GAME BD OCEAN HUNTER (833-13571)

__SCREF (10) MBX 55, y Qa & spring washers. used, ¢ fl / “5 ’ Qlat & spring washers used \

PART Na. DESCRIPTION 837-12715-91 MODELS STEP2 CPU BOARD 837-13368 MODEL3 STEP2.7 VIDEO BD

8234-13572 ROM BD THE OCEAN HUNTER

337135 76—-COM PFSB SEC BD OCN COM

Page 59
  • DESIGN RELATED PARTS

OPPOSITE SIDE a \ OPIOSTE SIDE

  • OPPOSITE SIDE Sag (a7 JIG

‘OPPOSITE SDE

ms OPROSTESICE aie LoL, OPPOSIIE SIDE af ut. Le CCECC) C1 G48) Cm) 2) 8)

NO. PART No. DESCRIPTION J OCN-1003-A STICKER SIDE COVER 2 OCN-1005-B STICKER CP SIDE L 3 OCN 1008-8 STICKER CP SIDE R 4 OCN-TME-B STICKER SIDE L

5 OCN 1046 € STICKER SIDE R

6 OUN-Z001-2 STICKER METER 7 QCNL2G01-£ STICKER CNT COVER L 8 — OCN-2001-D STICKER CNT COVER R 9 OCN-201-# STICKER COVER LOWER 1 10 OCN 2001-F STICKER COVER LOWER R 11 OCN-2002-2 CNT PRL SHEET OCN 12 OCN-3001 B STICKER SEAT UPFER 13 OCN-3001-C STICKER SEAT LORER VA OCN-SOUSA STICKER SEAT SIDE L 15 OCN-3004-A STICKER SEAT SIDE 8 16 421-8875 STICKER PTY SIDE L 1? 421-9976 STICKER VI¥ Sih R 18 422-0700] PLAY INSTR SH OCN DX ENG

54,

Page 60
  • PARTS LIST TOP ASSY OCEAN HUNTER DX
Page 61

TOP ASSY OCEAN HUNTER DX

ITEM NO.

a oo he

a an PART NO.

OCN-0300 OCN-1000 OCN-1400 OCN-3000 MGL-0001 422-0700-01

FAS-300001 000-P00408-¥B 000-P00420-¥B 008-T00412-0B DESCRIPTION

ASSY TUBE ASSY CTRL CABI ASSY PTV ASSY SEAT&BASE JOINT BRKT PLAY INSTR SH OCN DX ENG

HEX BLT CRM W/FS M8 x 20 M SCR PH W/FS BLK M4 x 8 M SCR PH W/FS BLK M4 x 20

TMP PRF SCR TH BLK M4 x 12

Page 62

ASSY MAIN BD (OCN-0100)

S, 201%, (103)

$20

ITEM NO.PART NO.IESCRIPTION
1OCN-0101WOODEN BASE MAIN BD
2OCN-0150ASSY SHIELD CASE
3OCN-0102SHIELD CASE BRKT
102601-6848RUBBER DUMPER
104601-8148UBBER DUMPER NR
201000-P00416-M SCR PH W/FS M4 X 16
202000-P00408-WM SCR PH WES M4 x 8
204030-000616-S[EX BLT W/S M6 X 16
205060-F00600FLT WSHR M6
Page 63

ASSY SHIELD CASE (OCN-0150)

Uy

TTEM NO. PART NO.

1 105-5240Y 2 105-§242X 3 839-0951 4 833-13571

101 260-0064

201 000-P00408-¥ 202 010-P00308-F 203 010-P00310-F 204 000-P00320-W 205 010-P00365-P DESCRIPTION

SHIELD CASE MODEL3 SHIELD CASE LID MODEL3 FILTER BD MODEL3 JPT GAME BD THE OCEAN HUNTER

FAN MOTOR DC12V

M SCR PH W/FS Ma x 8 S-TITE SCR PH ¥/F M3 x 8 S-TITE SCR PH #/F M3 X 10 M SCR PH WARS M3 X 20 S-TITE SCR PH W/F M3 x 65

Page 64

ASSY TUBE (OCN-0300)

ITEM NO. PART NO. DESCRIPTION

1OCN-0301TUBE BOX
2DUT-0102TUBE BOX FRONT
3601-10360-29STOPPER RING 29
101310-5285-290070“FLEX TUBE 29-0070CM
102310-5286-29CONN 29
103310-5287-29CONN L 29
201000-P00408-WBM SCR PH W/FS BLK M4 x $
202050~-H00400HEX NUT M4
203060-S00400SPR WSHR M4
204060-FO0400FLT WSHRM4
  • THIS PART MAY DIFFER FROM THE ONE CALLED OUT ABOVE
Page 65

ASSY CONTROL CABI (OCN- 1000)

2 Adkcove Puce

Page 66

ASSY CONTROL CABI (OCN- 1000)

re

201, PART NO.

OCN O100 OCN-1001 OCN 10380 OCN-1035 OCN- 1040-01 OCN-1045 OCN-10b0 OCN-1055 OCN-1060 OUN-2050 OCN-2070 OCN-2100 OCN-2290 {KCN-4000 OCN-4100 (CN-1003 OCN- £004 OCN-1005 OCN-1006 MGL LOO’ MGL-1009 UCN LOU7 MGL-1016 MGL 1023 MGL-1024 MGL~-1025% MGL-1026 253-5366 COP-1213 COF-1214 OCN 1008 OCN-2002 OCN 2003 OCN-1018 MGL- 1011 MGL-1012 OCN-3558

130- 5096 280-0419

HO0-TOOS1 2-0C O00 THOS25 OC 000-FO05 | 2-7 000-T00416-00 000-F00408-7 068-141616-00 50-F00400 OO8-T00416-00 032-0042 DESCRIPTION

ASSY MAIN BD ASSY SURCABT CTRI. AC UNLT SW UNTT METER UNIT TWIN ASSY TOP PANEL ASSY WIRE L ASSY WIRE R ASSY BACK LID ASSY CONTROL MECHA L ASSY CONTROL MECHA R ASSY CLUTCH MOTOR ASSY START SWITCH ASSY PWR SPLY ASSY ELEC SIDE COVER L SIDE COVER R CP SIDE COVER L CP SIDE COVER R SPEAKER HOLDER L SPEAKER HOLDER R INSTR BASE INSTR COVER SHOULDER BLT HOLTER BUTTON BUSH FLT WSHR 5. 2-11 * 2.0 CASH BOX WATER GUARD A WATER GUARD Th PANEL LID LOWER CNT PNL BASE CNT PNL LID INSULATOR SHEET BD BASE BRKT UPPER BD BASE BRKT LOWELK RING PLATE

ASSY SERVO SPEAKER EOX TARNESS LG

M OSCR TIL CRN MS » 12 M SCR TH CRN NS & 25 M OSCR PIT W/TS M5 & 12 M OSCR ‘TH CRN id & 16 M SCR PIT W/7S M4 x 8 FLT WSHR CRN 4. 4-16 X 1.6 FLG NUT M4 ‘TMP PREF SCR TH CRM N4 * 16 WING BLT M4 & 25

Page 67

ASSY CONTROL CABI (OCN- 1000)

ITEM NO.

2ll PART NO.

068-441616 000-P00408-WB 000-T004.08-0B 068-441616-0B 060-S00400 060-F00400 030-000612-S 020-000412-02 008-T00410-0C 030-000820-S 060-F 00800 ESCRIPTION

FLT WSHR 4.4-16 x 1.6 M SCR PH WAFS BLK M4 x 8 M SCR TH BLK N4 x 8 FLT WSHR BLK 4.4-16 x 1.6 SPR WSHR M4 FLT WSHR M4 EX BLT W/S M6 X 12 EX SKT H CAP SCR BLK OZ M4 x 12

TMP PRF SCR TH CRM M4 x 10

EX BLT ¥/S M8 x 20 FLT WSHR M8

Page 68

ASSY SUBCABI CTRL (OCN-1001)

ANAT A. i.

JG AMA ES > ig EI Bt eB

yo

©

Page 69

ASSY SUBCABI CTRL (OCN-1001)

PART NO.

OCN-1002 MGL-1022 MGL-1013 MGL-1014 MGL-1017 MGL-1018X HN-1042X 105-5107 DP-1167 105-5170 105-5188 BY-4102 OCN-1009 OCN-1010

220-5237-92- ~ 220-5482-91- ~ 220-5575 220-5574 260-0011-02 601-8543 280-5172-15021 280-5187-26 601-5526-084

000-P00408-W 000-T00408-0C 000-F00308 000-P00345-¥ 050-F00400 FAS-000029 000-PO0416-¥ 000-P00406-7 DESCRIPTION

CTRL CABI TOP SPACER FLOOR MAT CTRL EDGE GUARD CASH BOX COVER WIRE COVER CTRL FAN BRKT CHUTE ‘TNG LKG LOCK BRACKET S HOLE COVER FAN MOTOR BRACKET SW PANEL PANEL BRKT

ASSY C.C 2DR ~ ASSY C.C 2DR ~ CAM LOCK MASTER W/0 KEY CAM LOCK W/KEYS AXTAL FLOW FAN AC100V 50-60H2 FAN GUARD STANDARD BUSHING MP 15021 OPEN LOCK BUSH 26 BUSH 1.6T (L= 84MM)

M SCR PH W/FS M4 x 8 M SCR TH CRM M4 x 8 M SCR FH M3 x 8 M SCR PH W/FS M3 x 45 FLG NUT M4 M SCR PH W/FS M4 x 50 M SCR PH W/FS M4 x 16 M SCR PH W/FS M4 x 6

Page 70

CTRL CABI (OCN-1002)

ITEM NO.PART NO.DESCRIPTION
1OCN-1002-ACTRL CABI BLANK
101601-6224CASTER ¢ 75

601-9377 CASTER FAI=75

102601-6063LEG ADJ 50
201930-000620-SHEX BLT W/S M6 X 20
202059-H01200HEX NUT M12
Page 71

AC UNIT (OCN-1030)

ok — 104) (105)

ITEM NO.PART NO.DESCRIPTION
1OCN-1031AC BRKT
101214-0202AC INLET PANEL TYPE
102509-5453-91-V-BSW ROCKER J8 V-B
103450-5135MAGNET CONTACT S-NIOCX AC 120V
104512-5046-10000C.P 10000MA CE UL

512-5046-5000 C.P 5000MA CE UL

105280-0417TERMINAL BINDING POST BLACK
201000-P00416-WM SCR PH W/FS M4 x 16
Page 72

ASSY TOP PANEL (OCN-1045)

ITEM NO. PART NO.

OCN-1046 OCN-1047 OCN-1048 MGL-1053 MGL-1054 ORwWH

201 050-F00400 202 012-P00410 203 060-F00400 DESCRIPTION

TOP PANEL SPEAKER NET L SPEAKER NET R DIFFUSER LOCK BRKT

FLG NUT M4 TAP SCR #2 PH 4 x 10 FLT WSHR M4

Page 73

SW UNIT (OCN-1035)

(orKte2) (1)

2007 |

(105 em, |

ITEN NO.PART NO.DESCRIPTION
1OCN-1036SW BRKT
10l220-5179VOL CONT B-SK OHM
102601-0042KNOB 22 NM
104509-5028SW PB IM (MIYAMA DS-412R)
105512-5033-1000CIRCUIT PROTECTOR 1000MA
Page 74

ASSY METER UNIT (OCN- 1040-01)

ITEM NO.

be Oo eo)

oor ||} com,

To

PART NO. DESCRIPTION

OCN-1042 METER BRKT TWIN 421-6591-01 STICKER COIN METER

220-5643-01 MAG CNTR DCSV 6P WH MZ-674-D04 220-5643-02 MAG CNTR DCSV 6P YE MZ-674-D05

Page 75

ASSY BACK LID (OCN- 1060)

S, (Hr)

ITEM NO. PART NO. DESCRIPTION

OCN-1061 BACK LID 2 DP-1167 TNG LKG

101 220-5575 CAM LOCK MASTER W/O KEY

Page 76

ASSY PTV (OCN-1100)

ITEM NO.

Aue wrNe ak XQ é we

nal H ad Nae La * ; Ne

“yin cy, u u AR

PART NO. DESCRIPTION

OCN-1150 ASSY FRONT PANEL

OCN-1200 ASSY BILLBOARD DYN-0501 PANEL MOUNT BRKT L

MGL-1150 ASSY MASK

DYN-0502 PANEL MOUNT BRAT R

RAL~0501 MASK HOLDER

200-5315-01-0CN 000-F00414 000-P00516-WB 000-T00520-0C 000-T00525-0C 068-552016-0C ASSY PROJECTION DISPLAY OCN M SCR FH M4 x 14 M SCR PH W/FS BLK M5 X 16 M SCR TH CRM M5 x 20 M SCR TH CRM M5 x 25 FLT WSHR CRM 5. 5-20 x 1.6

Page 77

ASSY FRONT PANEL (OCN-1150)

ES

{

| (6) LI} & 7 * i. 7) fon

12 ! iy "|

ITEM NO.PART NO.DESCRIPTION
1OCN-1151FRONT PANEL
2OCN-1152SERVICE DOOR

3 CPT-1205 BRKT LOWER

4CPT--1204BRKT UPPER
5CPT-1203SIDE BRK’
6DP-1148XLKG ING
7117-0062PLATE LOCK RETAINER
8117-5098TNG RETAINER PLATE
iOL220-5875CAM LOCK MASTER W/O KEY
201068-552016FLT WSHR 5.5-20 x 1.6
202050-F00500FLG NUT M5
203011-T00312TAP SCRTH 3 x 12
204000-T00430-0CM SCRTH CRM M4 x 30

®B (

Page 78

ASSY MASK (MGL-1150)

i a i Pan bel feu |

ITEM NO. PART NO.

1 MGL-1102 2 MGL-1151 3 MGL~1152

201 012-F00408-0B 202 000-F 00410 DESCRIPTION TV MASK SLIT PLATE MASK SIDE HOLDER

TAP SCR #2 FH BLK 4 x 8 M SCR FH M4 x 10

Page 79

ASSY BILLBOARD (OCN-1200)

ITEM NO.

Rone PART NO.

OCN-1201 OCN-1202 OCN-1203 LOCAL PURCHASE

LOCAL PURCHASE

280-5275-SR10 000-T00408-0C 000-P00430-S 068~441616 DESCRIPTION

BILLBOARD BILLBOARD BOX BILLBOARD HOLDER FL HOLDER

ASSY FL30W EX W/CONN HIGH T CE

CORD CLAMP SR1 M SCR TH CRM M4 x 8 M SCR PH W/S M4 x 30 FLT WSHR 4. 4-16 x 1.6

Page 80

ASSY CONTRL MECHA L (OCN-2050)

165 «

ITEM NO.

Se moon ewe

eso Ee PART NO.

OCN-2051 OCN-2053 OCN-2054 OCN-2057 OCN-2058 OCN-2059 OCN-2500 OCN-2004X OCN~2005

601-8541 100-5169 100-5307

030-000820-S 060-F00800 000-F00308 050-U00400 020-000820-02 030-000812-S 060-S00800-0B 050-H01200 050-U00800 DESCRIPTION

CONTROLLER BASE L SPRING HOOK L LINK BRKT L SLIDE RAIL BRKT EXT SPRING UBBER PLATE ASSY CONTROLLER SHAFT OD M12

)PPER RI-30 LIDE RAIL ODEND RBH12 nn

EX BLT W/S M8 x 20 FLT WSHR M8 M SCR FH M3 x 8 U NUT M4 HEX SKT H CAP SCR BLK 02 M8 x 20 EX BLT W/S M8 x 12 SPR WSHR BLK M8 EX NUT M12 U NUT M8

Page 81

ASSY CONTRL MECHA R (OCN-2070)

ITEM NO. PART NO.

1 OCN-2071 3 OCN-2073 4 OCN-2074 7 OCN-2057 8 OCN-2058 9 OCN-2059 10 OCN-2500 ll OCN-2004X 12 OCN-2005

101 601-8541 103 100-5169 104 100-5307

201 030-000820-S 202 060-F00800 203 000-F00308 204 050-U00400 205 020-000820-02 206 030-000812-S 207 060-S00800-0B 208 050-H01200 210 050-U00800 meng fe)

DESCRIPTION

CONTROLLER BASE R ING HOOK R NK BRKT R LIDE RAIL BRKT ‘T SPRING UBBER PLATE SSY CONTROLLER IAFT 0D M12 ASPmmnrn

STOPPER RI-30 SLIDE RAIL ODEND RBH12

HEX BLT W/S M8 x 20 FLT WSHR M8 M SCR FH M3 Xx 8 U NUT M4 EX SKT H CAP SCR BLK 0Z M8 x 20 EX BLT W/S M8 xX 12 SPR WSHR BLK M8 EX NUT M12 U NUT M8

Page 82

ASSY CLUTCH MOTOR (OCN-2100)

ITEM NO.

wre non

PART NO.

OCN-2101 OCN-2102 OCN-2103

350-5562-01

000-P00410-¥ 028-C00416-P 020-000412-02Z DESCRIPTION

MOTOR BRKT CAM KEY 4 X 4 X 20

GEARED MOTOR-CLUTCH UNIT W/S. P

M SCR PH W/FS M4 x 10 SET SCR CH CUP P Md x 16 HEX SKT H CAP SCR BLK OZ M4 x 12

Page 83

ASSY START SWITCH (OCN-2200)

(>) (Apply to the reverse side)

ITEM NO. PART NO. DESCRIPTION

1OCN-2201START SW PLATE
2421-7907- ~DENOMI SH ~
101509-5610-04YESW PB 30M YELLOW W/L 1P SV 3W
102509-5610-05YESW PB 30M YELLOW W/L 2P 5V 3¥
Page 84

ASSY CONTROLLER (OCN-2500)

Page 85

ASSY CONTROLLER (OCN-2500)

ITEM NO. PART NO.

i OCN-2550 2 QCN-2600 3 OCN-2001 4 OCN-2501X 5 OCN-2502 6 OCN-2503 7 OCN-2504 8 OCN-2505 9 OCN-2506 10 OCN-2507 13 OCN-2510 14 TTR-2009 15 601-7944 16 601-6005 17 OCN-2511 18 OCN-2512

191 220-5484 105 100-5329

201 0120-000412-02 202 050-00800 203 000-P00410-WB 204 000-P00408-F 205 028-A00408-P 206 0501100500 207 028 -A00304-P 208 000-T00408-0C 209 050-100400 210 068-441616-0C 2l2 060-500400-0B 213 020-000520--02 2l4 060-500500-08 215 060-F00500-0B 216 000-P00540-WB 217 060-F00400 DESCRIPTION

ASSY SWING BASE ASSY GRIP CONTROLLER COVER PITCH BASE GRIP LID LOWER COVER STOPPER SHAFT STOPPER RUBBER VR BRKT PITCH HOUSING WEIGHT LOWER GEAR HOLDER 80 GEAR 15 ADJUST GEAR WEIGHT BRKT UPPER WEIGHT BRKT LOWER

VOL CONT B-SK OHM BEARING 15 (680222)

HEX SKT H CAP SCR BLK 02 M4 x 12 U NUT M8 M SCR PH BLK W/FS M4 X 10 M SCR PH W/IS M4 <8 SET SCR HEX SKT CUP P M4 x 8 U NUT NB SET SCR HEX SKT CUP P M3 x 4 M SCR TH CRM M4 X 8 U NUT M4 FLT WSHR CRM 4.4-16 x 1.6 SPR WSHR BLK 4 HEX SKT H CAP SCR BLK M5 % 20 SPR WSHR BLK MS FLT WSHR BLK M5 M SCR PH W/FS BLK M5 x 40 FLT WSHR N4

Page 86

ASSY SWING BASE (OCN-2550)

Ou,

Oman

ITEM NO. PART NO. DESCRIPTION

1OCN-2551XSWING BASE
2OCN-2552SWING SHAFT
3OCN-2553VR BRKT SWING

4 OCN-2554 GEAR HOLDER

5OCN-2555STANDBRKT
6OCN-2556BOTTOM STOPPER
7OCN-2557COLLAR
101220-5484VOL CONTB-5K OHM
102601-6555GEAR Z=30 M=0. 75
103601-6450GEAR 110
201FAS-500022EX NUT P1.5 #3 M22
202000-P00410-WM SCR PH W/FS M4 X 10
203028-A00404-PSET SCR HEX SKT CUP P M4 x 4
204000-P00316-¥M SCR PH W/FS M3 x 16
205000-P00512-WN SCR PH W/FS MS x 12
206068-552016-0CFLT WSHR CRM 5.5-20 x 1.6
Page 87

ASSY GRIP (OCN-2600)

To solder

ITEM NO. PART NO. DESCRIPTION

1 OCN-2601 THUMB LID

101 610-0547 ASSY TRIGGER HANDLE W/O THUMB

Page 88

ASSY SEAT & BASE (OCN-3000)

7 cai ee

fa in) pd

for(i _ ADE

U T a SEE A a)

Page 89

ASSY SEAT & BASE (OCN-3000)

ITEM NO.PART NO.DESCRIPTION
iOCN-3001BASE
2OCN-3002SEAT
3OCN-3003SEAT SIDE COVER L

4 OCN-3004 SEAT SIDE COVER R 6 MGL-3007 SPEAKER LID

5MGL-~3004WIRE COVER

7 MGL-3008 FLOOR MAT REAR

8 MGL-3009 EDGE GUARD

9 MGL-3010 WIRE COVER S il OCN-3001-B STICKER SEAT UPPER

10GFR-3004ASSY SUPER WOOFER

12 OCN-3001-C STICKER SEAT LOWER

101280-3187-26OPEN LOCK BUSH 26
201000-P00618M SCR PH M6 X 18
202000-T00410-0CMSCCRM M4 x 10
203000-P00408-¥M SCR PH W/FS M4 x 8
204000-F00308M SCR FH M3 x 8
205032-000425WING BLT M4 x 25
206068-441616FLT WSHR4. 4-16 x 1.6
207060-S00600SPR WSHRM6
208068-652016FLT WSHR6.5-20 X 1.6
Page 90

BASE (OCN-3001)

ITEM NO. PART NO.

MGL-3001LX-A

601-6224 601-9377 601-6063

030-000620-5 050-H01200 DESCRIPTION

BASE BLANK

CASTER ¢ 75 CASTER FAI=75 LEG ADJ 50

HEX BLT W/S M6 x 20 HEX NUT M12

Page 91

ASSY SUPER WOOFER (GFR-3004)

ITEM NO. PART NO. DESCRIPTION

1MGL-3005SPEAKER BASE

2 MGL-3006 SPEAKER BRKT

101130-5097SPEAKER BOX SUPER WOOFER
201011-T00312TAP SCR TH 3 x 12
202000-P00516-WM SCR PH W/FS M5 x 16