Tempest Troubleshooting Guide TM-195 1st Printing
Tempest (rev 3, Revised Hardware) (Atari, 1980) · Troubleshooting · 24 pages · 44 sections · original scan
Ast printing
TROUBLESHOOTING GUIDE
Complete with Signatures and Memory Map
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Complete with Signatures and Memory Map
9g
Copyright © 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process. or in the form of a phonographic recording, nor may it be stored in a retrieval system. transmitted, or otherwise copied for public or private use. without permission from the publisher
The Tempest™ game piay. all graphic designs, this troubleshooting guide, the technical manual. Its accompanying schematic diagrams, and the monitor manual are protected by the new Copyright Act of 1976.
This Act provides for increased penalties for violating federal copyright ‘Jaws. Courts can impound infringing articles while iegal action is pending. If infringers are convicted, courts can order destruction of the infringing articles.
In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys fees, fines up to $25,000, and face an imprisonment of up to one year.
Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases. such copies risks forfeiting such a game.
Published by: ATARI INC. 1265 Barregas Avenue P.O. Box 427 Sunnyvale, California 94086
Reoroauced in the U.S.A 9K
Table of Contents
1 Memory Map... cece cece cence ees 1
2 Watchdog ..... ccc cece cent ee 2
3 Troubleshooting Using the CAT Box 2 A. CAT Box Preliminary Set-up ............ 2 B. Address and Data Lines . . 2 C. RAM... cee eee eee _ 3 D. Option Switch Inputs . . . 3 E. Custom Audio I/O Chips . 4 F. Player Input Switches and Encod a) G. LED and Coin Counter Outputs... 2.0... eee eee eee 5
4 Troubleshooting with Signature Anaiyals. . 6 A. Signature Analysis Set-up . 6 B. Clock and Reset Circuitry 7 C. Address Lines ....... 7 D. Address Decoder . .7 E. ROM and Data Lines 8 F. Math Box an
List of Illustrations
Figure? MemoryMap........ 0.60 c eet eee trae ee 1 Figure 2 Address and Data Lines . 3 Figure 3 Custom Audio I/O Chips . 4 Figure 4 Led and Coin Counter Addresses . 5
Figure 5 Analog Vector-Generator Data 6 Figure 6 S.A. Harness Assembiy .. . Figure 7 S.A. Harness Assembly
WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service
Atari, inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427. Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 om Pacific Time) z= From California, Alaska or Hawaii (408) 745-2900 s From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A. Game sales and service only
Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey zs (201) 469-5993 From anywhere else in this area © ‘toll-free (800) 526-3849
EUROPE Parts for all Atari customers in Western Europe. Game sales and service
Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Teiex 28165 (Monday-Friday, 9:00-6:00 pm GMT)
@ 062-52155
1 Memory Map
MEMORY MAP
HEXA- DECIMAL | RAW DATA FUNCTION ADDRESS jor 06 DS D4 D3 D2 D1 DO
| 0000-7FFF | RW)/D D | D D D D | D_ OD | | Program RAM (2K) |
0800-080F | W DBD OD D OD | Color RAM
| cso | R | D | Right Coin Switch | |
| coo | R | o | Center Coin Switch |
| coo | R | D | Left Coin Switch |
| ocoo | R | 12} | Slam Switch |
| ocoo | R | D | Self-Test Switch |
| O0C00 | R | D | Diag. Step Switch |
| ocoo | R | D | HALT |
| ocoo | R|D | 3KHz | |
| QD00 | R|}0 | DD D D D | D OD | Option Switch Inputs |
| QE00 | R|D DO DBD | D D D 2D | | Option Switch Inputs |
| 2000-2FFF | |RW}D D D D D DO | D OD | | Vector RAM (4K) |
3000-3FFF | R}O0 D D D D D D OD | Vector ROM (4k)
| 4000 | wi | D | Right Coin Counter | |
| 4000 | Ww | 1) | Center Coin Counter |
| 4000 | w | is) | Video Invert X |
| 4000 | w | ie) | Video Invert Y |
| 4800 | Ww | VG GO | |
| 5000 | Ww | WO CLEAR | |
| 5800 | Ww | VG Reset | |
| | 6000-603F | wj0 D D0 DD D D OD! | EAROM Write | |
| 6040 | w|O 0 DD D D OD D| | EAROM Control | |
| 6040 | R | 1D | Math Box Status |
| 6050 | R|O 0 0 D D D D ODO} | EAROM Read |
=
| e060 | | R|D DD DD D D | D| | Math Box Read | |
| 6070 | R |} O0 DO D OD D D OD] | Math Box Read | ||
| 1 6080-609F | w{|D D DD O | D | OD OD! | Math Box Start |
eocosocF ;RW|D D0 D0 D D D D OD | Custom Audio Chip 1 e6one6oDF |RW/D 0 DDO DD D | Custom Audio Chip 2
| 60E0 | R | | D | One Player Start | |
| 60EO | R | D | Two Player Start |
| |_ 60€0 | R | D | FLIP |
| gooo-bFFF | Rj} | D D D D O | D OD | Dj Program ROM (20k) | |
[ain
Figure 1 Memory Map
2 Watchdog
The Watchdog circuit will cause continuous reset pulses to the microprocessor if a problem exists within the microprocessor circuit. If the self-test fails to run, it is a good practice to check the reset line.
RESET-microprocessor input (pin 40). In a properly operating game, reset should occur during power-up or when the reset push button is activated. A pulsing reset line indicates that something is causing the microprocessor to lose its place within its program. Typical causes are: . Open or shorted address or data bus lines . Bad microprocessor chip Bad bus buffers |. Bad ROM . Bad RAM . Any bad input or output that causes an address or data line to be held in a constant high or low state Oahwnn
A pulsing RESET signal indicates a problem exists somewhere within the microprocessor circuitry rather than within either the Math Box or the Analog Vector Generator.
3 Troubleshooting
Using the CAT Box
A. CAT Box Prelim-
A. CAT Box Prelim inary Set-up
- Remove: @ The electrical power from the game. @ The wiring harnesses from the game PCBs. @ The main and auxiliary boards from the game cabinet.
e fll microprocessor chip C2 from the main
B.
- Connect: @ The harnesses from the game to the main and auxiliary boards. (Use extender cables if available.) 00 and@2 test points together. WD DIS test point to ground. The CAT Box flex cable to the main PCB test edge connector.
- Power Up: @ The game. @ The CAT Box.
- Set CAT Box Switches: @ TESTER SELF-TEST: (OFF) @ TESTER MODE: RW @ Press TESTER RESET
B. Address and Data Lines
1, Perform the CAT Box preliminary set-up.
- Connect the DATA PROBE to the CAT Box and the game ground test point.
- TESTER MODE: R/W
BYTES: 1. . PULSE MODE: UNLATCHED . R/W MODE: (OFF) Key in address pattern on the keyboard (use AAAA to start) . Push DATA SET ). Key in data pattern on the key board (use AA to start) . RIW MODE: STATIC . Probe the IC-pin with the data probe and check for the 1 or 0 LED as indicated in Figure 2. Repeat this step for each address and data line.
- Repeat steps 6-11 using 5555 in step 7 and 55 in step 9. FPS © Noms
Figure 2 Address and Data Lines
| When writing | Address and | When writing |
| AAAA pattern | data lines | 5555 pattern |
| Logic State | IC-Pin | Logic State |
| 1 | B3-1 | 0 |
| ie) | 83-3 | 1 |
| 1 | B3-2 | 0 |
| 0 | AIB-3 | 1 |
| 1 | AIB-18 | (e) |
| 0 | AIB-16 | 1 |
| 1 | AIB-14 | ie) |
| 0 | AIB-12 | 1 |
| 1 | BIC-3 | 0 |
| 0 | BIC-5 | 1 |
| 1 | BiC-7 | 0 |
| 0 | BIC-9 | 1 |
| 1 | BIC-18 | QO |
| 0 | BIC-16 | 1 |
| 1 | BIC-14 | ce) |
| 0 | BIC-12 | 1 |
| 1 | F2.9 | le) |
| 0 | F2-8 | 1 |
| 1 | F2-7 | ie) |
| 0 | F2-6 | 1 |
| 1 | F2-5 | Q |
| 0 | F2-4 | 1 |
| 1 | F23 | 0 |
| 0 | F2-2 | 1 |
C. RAM
- Perform the CAT Box preliminary set-up.
- Set the CAT Box switches as follows: a. Press TESTER RESET b. DBUS SOURCE: ADDR c. BYTES: 1024 d. R/W MODE: (OFF) e. R/W: WRITE f. Enter 0000_on the keypad g. Toggle R/W MODE to PULSE and back to (OFF) h. RIW: READ i. Toggle R/W MODE to PULSE and back to (OFF)
- If the CAT Box reads an address that doesn’t compare, the COMPARE ERROR LED lights up, the ADDRESS/SIGNATURE display shows the failing address location, and the ERROR DATA DISPLAY switch is enabled. Using this switch, determine if the error is in the high- or low-order RAM.
- Repeat the test with DBUS SOURCE set to ADDR.
- Repeat steps 2-4, entering 0400 on the keypad (step f).
- Repeat steps 2-4, entering 2000 on the keypad (step f.
- Repeat steps 2-4, entering 2400 on the keypad (step f).
- Repeat steps 2-4, entering 2800 on the keypad (step f).
- Repeat steps 2-4, entering 2C00 on the keypad (step f).
D. Option Switch Inputs
. Perform the CAT Box preliminary set-up. BYTES: 1 RIW: READ . RIW MODE: (OFF) . Key in OD00 . RIW MODE: STATIC . Activate the option switches at location N13 while monitoring the DATA DISPLAY. The DATA DISPLAY will change if the switches are operating properly,
- Repeat steps 4-7, entering 0E0@ in step 5, and activate switches at location L12. Nogbons
E. Custom Audio
I/O Chips
Perform the CAT Box preliminary set-up. BYTES: 1 RW: WRITE RW MODE: (OFF) Enter address from Figure 3 Press DATA SET . Enter the data from Figure 3 RW MODE to PULSE and back to (OFF) . Repeat steps 5-8 for each address and data, noting the test results. POENOMPeEp>
Figure 3 Custom Audio I/O Chips
| ADDRESS | DATA | TEST RESULTS | ADDRESS | DATA | TEST RESULTS |
| 60CF | 00 | 60DF | 00 | ||
| 60CF | 03 | 60DF | 03 | ||
| 60C0 | 55 | 60D0 | 55 | ||
| 6001 | AF | Custom Audio I/O Chip | 60D1 | AF | Custom Audio I/O Chip |
#1 channel 1 produces #2 channel 1 produces pure tone. pure tone.
| 60C1 | 00 | Custom Audio W/O Chip | 6001 | 00 | Custom Audio 1/0 Chip |
#1 channel 1 off. #2 channel 1 off.
| 60C2 | 55 | 60D2 | 55 | ||
| 60C3 | AF | Custom Audio I/O Chip | 60D3 | AF | Custom Audio W/O Chip |
#1 channel 2 produces #2 channel 2 produces pure tone. pure tone.
| 60C3 | 00 | Custom Audio /O Chip | 60D3 | 00 | Custom Audio I/O Chip |
#1 channel 2 off. #2 channel 2 off.
| 60C4 | 55 | 60D4 | 55 | ||
| 60C5 | AF | Custom Audio /O Chip | 60D5 | AF | Custom Audio VO Chip |
#1 channel 3 produces #2 channel 3 produces Pure tone. pure tone.
| 60C5 | 00 | Custom Audio I/O Chip | 60D5 | 00 | Custom Audio I/O Chip |
#1 channel 3 off. #2 channel 3 off.
| 60C6 | 55 | 60D6 | 55 | ||
| 60C7 | AF | Custom Audio I/O Chip | 60D7 | AF | Custom Audio /O Chip |
#1 channel 4 produces #2 channel 4 produces pure tone. pure tone.
| 60C7 | 00 | Custom Audio I/O Chip | 60D7 | 00 | Custom Audio I/O Chip |
#1 channel 4 off. #2 channel 4 off.
F. Player Input Switches and
Encoder Wheel
. Perform the CAT Box Preliminary Set-up . DBUS SOURCE to DATA BYTES: 256 RW: WRITE RW MODE: (OFF) . Key in 60D0 . Press DATA SET . Key in 00_ ). Toggie R/W MODE to PULSE and back to (OFF) 10, BYTES: 1
- RW: READ
- Key in 60D8
- MODE: STATIC
- Pushing the following player input switches should cause the DATA DISPLAY to change: FIRE, SUPERZAPPER, 1-player start and 2-player start. (Also Player-2 FIRE and Player-2 SUPER- ZAPPER in cocktail" games.) OSNOGREOM=
*To test player-2 inputs in cocktail games connect IC D6-1 to +5.
G. LED and Coin Counter Outputs
. Perform the CAT Box Preliminary set-up. DBUS SOURCE to DATA BYTES: 1 RW: WRITE RW MODE: (OFF) Key in address from Figure 4 Press DATA SET Key in on or off data from Figure 4 . R/W MODE to STATIC and back to (OFF) Repeat steps 6-9 to turn off coin counter solenoids, or to test another address. SeEPNgapoNns
If you write data that activates a solenoid, deactivate it by pressing the reset button on the game board or by writing “off” data. If you leave a solenoid activated for more than about 10 seconds it will overheat and may have to be replaced. Figure 4 LED and Coin Counter Addresses
ADDRESS ON-DATA OFF-DATA OUTPUT NAME
| 4000 | or | 00 | Right Coin Counter |
| 4000 | 02 | 00 | Center Coin Counter |
| 4000 | 04 | 00 | Left Coin Counter |
| 60E0 | FD | FF | _‘t-piayer start LED |
| 60EO | FE | FF | 2player start LED |
H. Analog Vector-
H. Analog Vector Generator
- Test: Perform CAT Box preliminary set-up. DATA SOURCE: DATA RW: WRITE R/W MODE: (OFF) Key in address from Figure 5 or press AD- DRESS INC. Press DATA SET Key in data from Figure 5 Set RW MODE to PULSE and then to (OFF) . Repeat steps 5-8 for each address in Figure 5 PEND OPON>
- RAW: READ
- RAW MODE: (OFF)
- Key in address or press ADDRESS INC.
- RW MODE: PULSE
- Check the data in the DATA DISPLAY against the data in Figure 5
lf you are sure the data is correct, proceed to steps 15-19:
- RAW MODE: WRITE
- RIW: (OFF)
- Key in VG GO address (4800 for TEMPEST™)
- RW to PULSE and then back to (OFF)
- After writing to the VG GO address, the monitor should show a large plus sign. Failure of the horizontal or vertical circuits shows up as a single line drawn on the monitor. /f your monitor does not display a large plus sign, contact Atari Field Service.
Figure 5 Analog Vector-Generator Data
Address Data Address Data Address Data
| 2000 | 40 | 200C, | FE | 2018 | 00 |
| 2001 | 80 | 200D | 03 | 2019 | 40 |
| 2002 | 00 | 200E | 00 | 201A | 80 |
| 2003 | 70 | 200F | 62 | 201B | 00 |
| 2004 | 00 | 2010 | 40 | 201C | 80 |
| 2005 | 1E | 2011 | 80 | 201D | 1F |
| 2006 | 00 | 2012 | 80 | 201E | 00 |
| 2007 | 1E | 2013 | 00 | 201F | 00 |
| 2008 | 00 | 2014 | 00 | 2020 | FF |
| 2009 | 60 | 2015 | 00 | 2021 | 40 |
| 200A | FF | 2016 | 01 | 2022 | 00 |
| 200B | 03 | 2017 | 1F | 2023 | EO |
4 Troubleshooting
With Signature Analysis
A. Signature Analysis Set-up
Perform the CAT Box Preliminary set-up.
Connect the three BNC to E-Z clip cables (supplied with the CAT Box) to the SIGNATURE ANALYSIS CONTROL START, STOP and CLOCK jacks on the CAT Box.
Attach the three black E-Z clips to a ground loop on the Tempest™ game PCB.
Attach the CAT Box data probe to the DATA jack on the CAT Box.
The colored E-Z clips on the cables will be moved about for each group of signatures to be taken. The set-up for each group of signatures is located on the schematic sheet near the device to be checked. The signatures are located on or near the signal point on the schematic.
Set the CAT Box switches as follows: @ TESTER MODE: SIG e@ TESTER SELF-TEST: OFF @ PULSE MODE: LATCHED @ START: As indicated @ STOP: As indicated @ CLOCK: As indicated
Power up the game board and the CAT Box.
B.Clock and Reset C. Address Lines Circuitry 1. CAT Box Settings for
2 s ircu .
; Address Bus Test
| NOTE: For this test, remove W DOG DIS from | Probe | Trigger | IC-Pin | Test Pt. |
GROUND.
| Start | a | 2-25 |
| Stop | ai | C2-25 |
1. CAT Box Settings Clock L 2-39 02 Stop + D38 2. Signatures
| Probe | Trigger | 1C-Pin | |||
| Start | S | AG-6 | A | ||
| Clock | Ss | D3-8 | Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
BIC1-12 ABO UUUU
| 2. Signatures | Bict-14 | ABI | 5555 | ||
| Logic Probe | Signal | Signature | BIC1-16 | AB2 | Ccccc |
| on IC-Pin | Name | Should Be | BIC1-18 | AB3 | TF7F |
| C4-3 | 6MHz | 1730 | B/C1-9 | AB4 | 5H21 |
| 4-2 | 3MHz | 3441 | BIC1-7 | ABS | OAFA |
| C46 | 1.5MHz | 5CPA | BIC1-5 | ABE | UPFH |
| C4-7 | 36H3 | BiC1-3 | AB7 | 52F8 | |
| F3-6 | E3MHz | 3441 | AIB1-12 | ABS | HC89 |
| F3-3 | E6MHz | 1730 | AIB1-14 | ABO | 2H70 |
| B48 | 7CUP | A/B1-16 | AB10 | HPPC | |
| B46 | 3KHz | P74P | AIB1-18 | ABI | 1293 |
| D4-8 | 3214 | A/B1-3 | AB12 | HAP7 | |
| 046 | C4P5 | B3-2 | A138 | 3096 | |
| D3-8 | RESET | 4668 | B3-3 | A14 | 3827 |
| E4-15 | FOF1 | B3-1 | AS | 755U | |
| E3-12 | v9s0 | AG4 | AG | 755P |
D. Address Decoder
- CAT Box Settings for Address Decoder Test
| Probe | Trigger | IC-Pin | Test Pt. |
| Start | 2 | AGS | |
| Stop | “L | AG-3 | |
| Clock | kL | o2 |
>
- Signatures 2. Signatures
| NOTE: To obtain Signatures from IC J5, ground | Logic Probe | Signal | Signature |
| R/W testpoint. | on IC-Pin | Name | Should Be |
| D1-9 | DBO | 1F4H |
1-10 4p:
Logic Probe Signal Signature pr ey toes
| on IC-Pin | Name | Should Be | 01-13 | DB3 | UH32 |
| B37 | ie) | F2A6 | Dit4 | pes | 4HEA |
| E32 | aio | F2A7 | D1-15 | DBS | oP76 |
| F3-8 | EO | F2A6 | D1-16 | DB6 | 86CP |
| 459 | VGRS | 5969 | D1-17 | DB7 | P29C |
J5-10 WOCLA OPCS
| J5-11 | VGGO | 270P |
a THEM Brie 3. CAT Box Settings for ROMO Test
| B34 | AA* | 4P0A | (LC. E1) |
J2-7 ROMS 56C3 Probe Trigger Testpoint
| 128 | ROM? | so19 | Start | Le | FOMO |
| . | 5AH1 | Stop | J | ROMO | |
| J2-4 | ROMS | SHUG | Clock | “Lh | 02 |
| J2-9 | ROM4 | 1920 | |||
| J2-10 | ROM3 | C34 | . | ||
| Jan | ROM2 | 597C | 4. Signatures | ||
| J212 | ROMi | UA87 | Logic Probe | Signal | Signature |
| C1-7 | ROMO | 4154 | on IC-Pin | Name | Should Be |
| eis | OMAK | a | E19 | DBO | 6481 |
| E1-10 | DB1 | P6AQ | |||
| E1-11 | DB2 | 9652 | |||
| E1-13 | 0B3 | 40F3 | |||
| E1-14 | 0B4 | 37C2 | |||
| E1-15 | DBS | OA18 | |||
| E1-16 | DB6 | A2C0 | |||
| £1-17 | DB7 | 9HCS |
- CAT Box Settings for ROM1 Test (1.C. FA)
E. ROM and Data Probe Trigger Testpoint
| Lines | ay | — | ROM |
| Clock | = | o2 |
270 pF capacitor between IC-Pin C2-23 and 6. Signatures
| ground. This can be done in the socket at C2. | Logic Probe | Signal | Signature | ||
| on (C-Pin | Name | Should Be | |||
| . | F1-9 | DBO | 3892 | ||
| 1. CAT Box Settings for ROMX Test | F4-10 | DBI | o1us | ||
| LC. D1 | F111 | DB2 | PH6P | ||
| ao ) | ti | Testooi | F113 | DB3 | UPOF |
| a | sipeint | Fig | DB4 | uPa4 | |
| Start | : | ROMX | F1-18 | DBS | CA33 |
| Stop | I | ROMX | F1-16 | DB6 | 3U05 |
| Clock | kL | o2 | F117 | DB7 | 8CP3 |
- CAT Box Settings for ROM2 Test (IC. H1)
Probe Trigger Testpoint
| Start | L | Roma |
| Stop | I | ROM2 |
| Clock | 1L | 02 |
- Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| H1-9 | DBO | T550 |
| H1-10 | DB1 | AOIF |
| H1-11 | DB2 | A540 |
| H1-13 | DB3 | 5U60 |
| H1-14 | DB4 | 2068 |
| H1-15 | DBS | 9767 |
| H1-16 | DB6 | 54CA |
| H1-17 | DB7 | 7F8F |
- CAT Box Settings for ROM3 Test (1.C. J1)
Start 1 ROMS
| Stop | a | ROM3 |
| Clock | LL | 02 |
- Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| J1-9 | DBO | 09A6 |
| J1-10 | DB1 | 6A12 |
| J1-11 | DB2 | 91CA |
| J1-13 | DB3 | 1OHP |
| J1-14 | DB4 | F53U |
| J1-15 | DBS | c67C |
| J1-16 | DB6 | 8272 |
| J117 | DB7 | F651 |
- CAT Box Settings for ROM4 Test (1.C. K1)
| Start | 1 | ROM4 |
| Stop | a | ROM4 |
| Clock | a | o2 |
- Signatures Logic Probe on IC-Pin K1-9 K1-10 Kt K1-13 K1-14 K1-15 K1-16 K1-17
Signal Signature
Name Should Be DBO A8FU DB1 U3U7 0B2 C8CH DB3 353F DB4 93FU DBS UFH1 DB6 A165 0B7 5399
- CAT Box Settings for ROMS Test (ILC. L/M 1)
| Start | +L | ROMS |
| Stop | aa | ROMS |
| Clock | LL | 02 |
- Signatures
| Logie Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| UM1-9 | DBO | 4876 |
| U/M1-10 | DB1 | 5397 |
| UM1-11 | DB2 | 7396 |
| UM1-13 | DB3 | C9CH |
| UM1-14 | DB4 | HF73 |
| U/M1-15 | DBS | 11U6 |
| L/M1-16 | DB6 | 43C8 |
| UM1-17 | DB7 | 2P85 |
- CAT Box Settings for ROME Test (I.C. M/N 1)
| Start | LL | ROM6 |
| Stop | J | ROM6 |
| Clock | LL | o2 |
- Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| MIN-9 | DBO | A4AC |
| MIN-10 | DB1 | 3A7C |
| MIN-11 | DB2 | OF22 |
| MIN-13 | DB3 | H221 |
| MIN-14 | DB4 | 2HO7 |
| MIN-15 | OBS | 818A |
| MIN-16 | DB6 | 1699 |
| MIN-17 | DB7 | 4149 |
- CAT Box Settings for ROM7 Test
- Signatures
| (1.C. P1) | Logic Probe | Signal | Signature | ||
| Probe | Trigger | Testpoint | re | ell | sree |
L H1
| Start | ROM? | NIP3-10 | DBI | 5UBC | |
| Stop | =i | ROM | NIP3-11 | DB2 | |
| Clock | L | 02 | — | ||
| N/P3-13, | DB3 | 507P | |||
| . | NIP3-14 | DB4 | 2A8P | ||
| 18. Signatures | Nees | Bes | 9FOC | ||
| 5 | ; | . | NIP3-16 | OB | AH97 |
Logic Probe Signal Signature
| on IC-Pin | Name | Should Be | NIP3-17 | oB7 | 298H |
| P1-9 | OBO | P4F3 | |||
| P1-10 | DBi | 2006 | |||
| Pt1-11 | DB2 | 4614 | NOTE: When taking signatures on |.C. R3, ground | ||
| P1-13 | OB3 | 7AG3 | IC-Pin B35. | ||
| P1-14 | DB4 | 434C | |||
| = | D | 3C66 | . |
ae pee peu 23. CAT Box Settings for Vector
| P17 | DB7 | 203A | ROM1 Test (I.C. R3) |
Probe Trigger IC-Pin Testpoint
19. CAT Box Settings for ROM8 Test Start kL R3-20
(I Cc R1) Stop a R3-20
| oe | Clock | Lh | 2 |
Probe Trigger Testpoint
ROM .
| aut | £ | Aone | 24. Signatures | ||
| Clock | LL | o2 | Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be | |||
| 5 | R3-9 | DBO | 3FH3 | ||
| 20. Signatures | R340 | DBI | OHSS | ||
| Logic Probe | Signal | Signature | R3-11 | DB2 | 9H5H |
| on IC-Pin | Name | Should Be | R3-13 | DB3 | 98PF |
| R1-9 | DBO | QHFP | R3-14 | DB4 | PA27 |
| R1-10 | DB1 | U7HH | R315 | 085 | 5U3H |
| R1-11 | OB2 | F32H | R3-16 | DB6 | 97FC |
| R1-13 | DB3 | Fé6U | R3-17 | DB7 | 583A |
| Rt-14 | DB4 | U379 | |||
| R1-15 | DBS | 4g0P | |||
| R1-16 | 0B6 | 5P99 | |||
| R1-17 | 0B7 | CFA8 |
- CAT Box Settings for Vector ROM Test (1.C. N/P3)
Start kL N/P3-20 Stop J NIP3-20
| Clock | oe | o2 |
F. Math Box
The Math Box signature analysis procedure is somewhat different from other procedures, so follow these set-up instructions for the three tests carefully.
In addition to your CAT Box or signature analyzer, you'll need an SA Harness Assembly. Order Atari part number A036836-01 or see Figure 6 to make your own.
A. Math Box Test #1 Procedure:
- Plug SA Harness Assembly Test #1 connector onto Signature Analyzer connector (J16) on the Auxiliary PCB.
- Connect the CAT Box Start, Stop and Clock E-Z hooks to the SA Harness Assembly as shown in Figure 7.
- On the main PCB, connect PWR ON RESET test Point to ground, and power-up the game and the CAT Box.
- Don’t remove the microprocessor (6502A) from the main PCB. Don't connect the 50 pin ribbon cable to the main PCB edge connector. Don't connect W DOG DIS to ground.
- Set the CAT Box switches as follows: a. START _J— b. STOP _j— c. CLOCK _J— d. TESTER MODE: SIG e. Press TESTER RESET
- With the logic probe touching the + 5V test point on the Auxiliary PCB, the ADDRESS/SIGNATURE display should read CC34. This will verify that your test set-up is correct. if you don’t get CC34, recheck your set-up.
Figure 6 S.A. Harness Assembly
S.A. Harness Assembly 12-CIRCUIT HOUSING MOLEX P.N. 09-50-7121
#1 CC34 TERMINAL MOLEX P.N. 08-50-0106 QUANTITY = 18
#23951 #33951
ca
- Signatures FIH2-8 7BAA*
| Logic Probe | Signature | J2:33 | 8638 |
| on IC-Pin | Should Be | 42-16 | 11C5* |
| crt | H58A | 28 | 7U19 |
| C1-12 | 77F7 | E2-34 | AIF7 |
| C1-13 | 85PA | 2-31 | 1781 |
| 1-14 | 7P25 | E2.16 | QAFH* |
| ott | SCPO | E511 | CAs |
| B1-12 | P5PH | 04-8 | 0600 |
| 01-13 | 725C | E4-11 | C34 |
| 01-14 | 96PF | F5-11 | C835" |
| F1-12 | 4PPF | pas | cava |
| Pitt | Ouro | £58 | 759 |
| F1-10 | 3CAP | £58 | 45A1* |
F1-9 AGA3 H1-12 26A6
| Ht-11 | S1HA | B. Math Box Test #2A | |
| H1-10 | P9C1 | P | dure |
| H1-9 | 2987 | rocedu |
J1-12 96U0
| J4-14 | UC59 | 1. Plug SA Harness Assembly Test #2 connector on- |
| J1-10 | 6989 | to Signature Analyzer connector (J16) on the Aux: |
| J1-9 | 3FU4 | iliary PCB. |
| K1-12 | O5A6 | 2. Connect the CAT Box Start, Stop and Clock E-Z |
| K1-11 | 60H6 | hooks to the SA Harness Assembly as shown in |
| K1-10 | PPF6 | Figure 7. |
K1-9 34c2 3. Don’t remove the microprocessor (6502A) from
| L112 | 58A1 | the main PCB. |
| 1-11 | 1AA2 | Don’t connect the 50 pin ribbon cable to the main |
| L1-10 | F74F | PCB edge connector. |
| L1-9 | 6CF6 | Don’t connect W DOG DIS to ground. |
Don’t connect PWR ON RESET to ground.
| E112 | F765 | 4. Set the CAT Box switches as follows: | |
| E1-11 | CPU8 | a. START _[— | |
| E1-10 | 0000 | b. STOP | 7_ |
| E1-9 | F515 | ce. CLOCK _ |
d. TESTER MODE: SIG
| F42 | cc34 | e. Press TESTER RESET |
E46 AGA3
| A26 | 0000 | 5. Enter the self-test mode and advance the screen |
| B12 | 8A7H | with the siam switch until the large rectangle ap- |
pears. This procedure is described in Figure 6,
| B15 | cu2P | Chapter 2 of the Tempest™ Operation, Mainte- |
| B16 | 4C6C | nance, and Service Manual. |
| B1-9 | 6U30 | 6. With the logic probe touching the + 5V test point |
| B1-12 | 5AAH | on the Auxiliary PCB, the ADDRESS/SIGNATURE |
display should read 3957. This wiil verify that your
| B1-15 | 0347 | test set-up is correct. If you don’t get 3951, re- |
| B1-16 | 9A08 | check your set-up. |
B1-19 2327
KIL2-33 6PUP NOTE: Signatures are listed in the order that they
should be done. As often as possible, /C-Pin
| K/L2-16 | 9AFH* | refers to a chip output. As a general rule, |
| K/L2-8 | 809A* | when a bad signature is discovered, the IC |
| FIH2-33 | gcPP | listed in the /C-Pin column can be suspect- |
| FIH2-16 | 1105* | ed as faulty. |
1, Signatures
Logie Probe on IC-Pin At-14 A1-13 A112 Att A1-10 A1-9 A1-7 A1-6 A15 A1-4 A133 Al-2 Att
IOODO00N000N0 Signature Should Be F722 C4P5 6UAC 3441 2P61 92F3 A856 3050 H8F9 9569 3U53 9F47 4FUF GND
CLOCK
START
STOP
Figure 7 S.A. Harness Assembly
B. Math Box Test #2B Procedure 1, Plug SA Harness Assembly Test #2 connector onto Signature Analyzer connector (J16) on the Auxiliary PCB.
- Connect the CAT Box Start, Stop and Clock E-Z hooks to the SA Harness Assembly as shown in Figure 7,
- Don't remove the microprocessor (6502A) from the main PCB. Don’t connect the 50 pin ribbon cable to the main PCB edge connector. Don't connect W DOG DIS to ground. Don’t connect PWR ON RESET to ground.
- Set the CAT Box switches as follows: a. START _Jb. STOP “L ¢. CLOCK _{~ d. TESTER MODE: SIG e. Press TESTER RESET
- Enter the self-test mode and advance the screen with the slam switch until the large rectangle appears. This procedure is described in Figure 6, Chapter 2 of the Tempest™ Operation, Maintenance, and Service Manual.
- With the logic probe touching the + 5V test point on the Auxiliary PCB, the ADDRESS/SIGNATURE display should read 3951. This will verify that your test set-up is correct. If you don’t get 3957, recheck your set-up.
- Signatures
Logic Probe Signature on IC-Pin Should Be C1-11 92F3 C1-12 A856 C1413 3050 C1-14 H8F9 01-11 9569 D1-12 3U53 01-13 9F47 01-14 4FUF B. Math Box Test #3 Procedure
- Plug SA Harness Assembly Test #3 connector onto Signature Analyzer connector (J16) on the Auxiliary PCB.
- Connect the CAT Box Start, Stop and Clock E-Z hooks to the SA Harness Assembly as shown in Figure 7.
- Don’t remove the microprocessor (6502A) from the main PCB. Don't connect the 50 pin ribbon cable to the main PCB edge connector. Don't connect W DOG DIS to ground. Don't connect PWR ON RESET to ground.
- Set the CAT Box switches as follows: a. START _[~ b. STOP “1 c. CLOCK d. TESTER MODE: SIG e. Press TESTER RESET
- Enter the self-test mode and advance the screen with the slam switch until the large rectangle appears. This procedure is described in Figure 6, Chapter 2 of the Tempest™ Operation, Maintenance, and Service Manual.
- With the logic probe touching the + 5V test point on the Auxiliary PCB, the ADDRESS/SIGNATURE display should read 3957. This will verify that your test set-up is correct. If you don’t get 3957, recheck your set-up.
- Signatures
Logic Probe Signature on IC-Pin Should Be E2-22 1441 E2-23 2883 E2-24 5107 £2.25 A20P J2-22 441H 2-23 883A J2-24 1074 32-25 20P9
1™ YOUR COMMENTS, PLEASE! roan eee panting
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm = Distributor
Address. — Operator City State Zip = Other.
Area Code Phone
First fold
No Postage Necessary 4 mailed in the United States
be | BUSINESS REPLY MAIL — FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA a POSTAGE WILL BE PAID BY ADDRESSEE be Atari, inc. be Attn.: Field Service/Coin-Op Division P. O. Box 427 a Sunnyvale, California 94086 Pe Pe a
Second od SSOS*~<—SsSSS
Wwoi4 aGpe si) edey
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ATARI INC 1265 BORREGAS AVENUE @ P.O. BOX 427 ® } SUNNYVALE, CALIFORNIA 94086 ot Commipion bts Compa ATARI Sree re Cw Ja 1er Communications Company