CATHODE RAY TOMES

Super Gem Fighter Mini Mix

Super Gem Fighter: Mini Mix (USA 970904) (Capcom, 1997) · Document · 17 pages · 23 sections · original scan

Page 1

Super Gem Fighter Mini Mix USA CPS-II Manual

By: CAPCOM

Scanned

By:

Az

Scanned a OY 13/2001 _ naz.arcadeheaven.com

Page 2

© CAPCOM CO., LTD. 1997 ALL RIGHTS RESERVED © CAPCOM U.S 4., INC. 1997 ALL RIGHTS RESERVED

OPE.. * “ORS MANUAL

/\\ V ARNING

This game ‘s United States of America and Canadi.. rt or operation outside of these count constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CAPCON” COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331 PM00202 092397

Page 3

CAPQON" coin-op, inc. Super GEM Fighter ™

THANK YOU FOR PURCHASING “Super GEM Fighter’. WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: CUSTOMER SERVICE 475 OAKMEAD PARKWAY SUNNYVALE, CA 94086 PHONE: (408) 522-5325 FAX: (408) 522-5331

THE SERIAL NUMBERS OF YOUR KIT ARE LOCATED ON THE GAME CARTRIDGES AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

AAMA “B" CARTRIDGE SERIAL NUMBER SERIAL NUMBER

“A" CARTRIDGE SERIAL NUMBER (BOTTOM OF CASE) vacoso0

DEPENDING ON THE TYPE OF KIT YOU PURCHASED, PLEASE RECORD THE SERIAL NUMBERS HERE:

“FULL” KIT A-CARTRIDGE SERIAL # B-CARTRIDGE SERIAL #

AAMA SERIAL #

“B” KIT B-CARTRIDGE SERIAL #

[Proprietary and confidential information, mot to be disclosed or copied without the express permission of CAPCOM® COIN-OF, INC

Page 4

1B CAIR@OM” co-op, inc. Super GEM Fighter™

TABLE OF CONTENTS

Table of Contents

Warranty Information

Kit Inspection

Caution a eecanececssneseusnscesscesssesssnecsssssesessssneessstnessneecsnuecene 2

“FULL” Kit , “B” Kit Preparation Installation Control Panel Overlay Cabinet Graphics Re-assembly of Components Remote Volume/Test Switch Control Panel Wiring WB A BW Ip

Game Cartridges

Test Mode Test Menu . 6 Accessing the Menu 6 How to Select an Item 6 Closing the Menu 6 Menu Item Descriptions . 6 Configuration Menu . 7 System Configuration 8 Game Configuration . 9

Wiring References JAMMA Connections i eeeeescccsscsssssesessssecsssssnseccsssscsssuusesssssusccesstucccneesesevees 10 Auxiliary Cable Connections 0 oescesccsesessssssesssssessssnteecessseccessunscescsstsscesssescneeesseness 10

Reference Information . Inside of Back-cover Game Case Controls and Connectors Typical Control Panel Layout

[Proprietary and confidentat information, not to be disclosed or ewpled without the express permission of CAPCOM® COIN-OF, INC] i

Page 5

CAPGOM” con-op,inc. Super GEM Fighter™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. CPS II System Cartridges One (1) Year B. Electronic and Mechanical Components: (90) days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided: :

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

ii [Proprietary and coniidential information, not to be disclosed or copied wichout the express permission of CAPCOM® COIN-OF, INC.]

Page 6

CAPO” coin-op, inc. Super GEM Fighter™

KIT INSPECTION

There are two kits available for conversion to Super GEM Fighter ™:

  • GEM1000 (“FULL” kit) contains the 2) GEM 1000B (“B” kit) contains the game complete game cartridges, all necessary graphics, software cartridge (B-cartridge) and must also be and replacement joysticks and button switches. installed to a current CAPCOM® System I game. The “FULL” kit is intended for conversion of most It includes all the necessary game graphics for a JAMMA-compatible, horizontal screen cabinets. cabinet conversion (marquee, control panel overlay, monitor card, etc.).
‘Check that all parts have been shipped with your kit.If any parts are missing, contact your distributor

immediately.

KIT PARTS LIST | Gew1000 | GEM1000B | PART NO. DESCRIPTION QTy GEM1400 CPS II System Cartridges (A/B ) GEM1400B CPS II System Cartridge (B) GE1200 Monitor Card PL00376 Clear Plexi for Marquee AW00258 Marquee AW00216 Overlay, Control Panel AW00259 Decal, Joystick & Button Switches AW00147 Decal, Cabinet Side AW00260 Decal - Top, _ Instruction 2] 2fele}ele)e;e)<e)e) 2]

MS00151 Button Plug 03-0052 Cable, Auxiliary Volume/Test 13-0066 Bracket, A-Cartridge Mounting {

|vAW00261Decal - Bottom., Instruction
qvPM00202Manual, Operators
\VvGE2030Joystick, 8-way
|v16-0130Switch, 1-Player Start Button (White)
Vv16-0131Switch, 2-Player Start Button (White)
q16-0133Switch, Button (Red)
Vv16-0134Switch, Button (Blue)
V16-0136Switch, Button (Green)

v Vv

; ‘Proprietary and confidential information, not to be disclesed or copied without the express permission of ~CAPCOM® COIN-OP, INC. 1

Page 7

@APBOMI" coin-op, INC. Super GEM Fighter™

CAUTION

Please read the following instructions to keep the PC board in good condition:

¢#Do not block the ventilation slots.

@Do not drop or bump the board.

@Do not spill any liquids on the case.

#Do not disassemble the case.

ATTENTION

@ y The product that you have purchased contains a recyclable

battery. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal

ie waste system. Check with your local solid waste official for

details in your area for recycling options or proper disposal.

DISASSEMBLING THE CASE OR REMOVING THE STICKER MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY

OF YOUR REPAIR WARRANTY.

2 Proprietary and coufidentia} information, wot fo be discloved or copied without the express permission of _CAPCOM® COIN-OF,

Page 8

CARGO COIN-OP, INC.

KIT INSTALLATION

WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME ISOFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

1, Disconnect and remove the old printed circuit board(s) from the cabinet.

  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.

4, Place the drill hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.

  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover, figure 1 (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *cover is not included in the kit.
  • Plug up unused holes with a wood dowel 1-1/8" diameter) and sand any rough edges.

INSTALLATION

Marquee Installation

  • Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
  • Install the new marquee and replace the plexi glass. Clear plexi glass is included in “full” kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most contro] panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and Press it over the edges,
  • Trim any excess from the overlay. Place the drill hole template on top of _ the overlay, aligning it with the joystick holes. Pierce through the overlay at each control pane! hole. Then, cut away overlay material covering the joystick and buiton holes. Remove the template and clean off the overlay. Super GEM Fighter ™
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover, figure. 1. (if required),

Overlay (Trim to size)

Figure 1: Overlay Installation

CABINET DECAL INSTALLATION

  • Remove monitor glass and install monitor card
  • Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

MARQUEE OVERLAY MONITOR CARD

INSTRUCTION DECAL - BOTTOM

DECAL - TOP

Figure 5: Cabinet Decal Installation

‘CAPCOM COD.-OP, 3

Page 9

@AP@ON coin-op, Inc. Super GEM Fighter ™ Re-assembly of Components’

  • Notice that there are two white buttons. See figure 2. The WHITE buttons are START buttons. Install the PLAYER ONE button on the top left-hand side of the control panel, and the player two button on the top right-side of the control panel. 1 Player NX

Figure 2: Start Buttons Red Green Blue Red Green Blue t/t 888 888

Button Plug Buttons ___

SER en) Bs

Figure 3: Control Panel Buttons and Switches

  • Install all buttons and retaining rings on the control panel as shown in Figure 3. Install one red buttons to the immediate right of each joystick, install one green buttons to the right of the red ones, and install one blue buttons to the right of the green ones.
  • Install the switches on the buttons as shown in figure 3. Orient the switches so that when a button is pressed, the plastic contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in figure 4.

Figure 4: Joystick Installation CONTROL PANEL WIRING

NOTE: all switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing JAMMA connectors to the control panel according to the chart in table 1.
  • Auxiliary cable hamess have extra cables. For this game kick harness are not used. Leave cables not connected and make sure unused cables are isolated.

To Volume Test itch Bracket vet Figure 6: Auxiliary Cable Harness

TEST SWITCH WIRING

  • Your cabinet may already equipped test switch. An optional test/volume bracket (see Figure 7) is available through your local CAPCOM distributor (part number 03- 0050). When installing, the test switch bracket should be mounted inside the coin door and on top of the cash box for easy access. (See Page 7 for wiring detail)

Figure 7: Test/Volume Bracket

  • If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may use stereo audio output connect to existing Q-SOUND POWER AMPLIFIER.

4 "Proprietary and confidential infarmation, not to be disclosed or copied withaut the express permission af CAPCOM® COIN-OP,

Page 10

e ICARCOM| COIN-OP, INC. Super GEM Fighter ™ AN CAUTION

IMPROPER INSTALLATION OF THE JAMMA HARNESS TO THE GAME CARTRIDGE WILL CAUSE DAMAGE TO THE ENCLOSED PCB.

GAME CARTRIDGE INSTALLATION

“FULL” KIT

  • Install the four (4) mounting brackets to the underside of the “A” cartridge as shown in Figure 10.

Figure 10: Mounting Bracket Installation

“FULL” KIT

  • Using the supplied wood screws, fasten the game cartridge case to the control panel shelf, as shown in Figure 11.

vere { Figure 11: Case Mounting

22, Connect the JAMMA harness connector and the auxiliary cable connector to the “A’ cartridge. If your cabinet is equipped with Q-SOUND, also attach the audio cables.

WARNING

DISASSEMBLY OF EITHER GAME CARTRIDGE WILL VOID YOUR WARRANTY.

“i B” KIT

  • To remove the existing “B” cartridge from the “A” cartridge, pull the old case clamps apart (see Figure 12). Carefully remove the old “B” cartridge and install the new “B’ cartridge.
  • Re-install the case clamps.

Figure 12 : Case Clamp Installation

  • Power-up the game and set all operator adjustable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

‘Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP.ING: 5

Page 11

CAP@OM" coin-op, INC. Super GEM Fighter ™ TEST MENU The test menu allows you to test the functions and configure the game. These items include input devices such as joysticks, buttons and coin door or switches, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

TEST MENU 1. ACCESSING THE TEST MENU . For a CAPCOM® cabinet, or a cabinet with

1.INPUTa test switch:
2.OUTPUTMake sure the game is on and push the test switch.

The screen shown left will appear.

SOUND & VOICE.For a cabinet without a test switch:

COLOR Push the blue test switch on the outside of the black plastic casing. DOT CROSS HATCH Refer to the inside back cover of the manual.

GAME DATA

  • HOW TO SELECT AN ITEM
CONFIGURATION.Use the PLAYER I JOYSTICK to move the

MEMORY CHECK arrow in front of the desired item and press the EXIT PLAYER I SHOT | button, as shown below in various control panel configurations: SELECT = 1P UP or DOWN

START=1P SHOT13.CLOSING THE TEST MENU

To close the Test Menu, highlight “9, EXIT” and push the PLAYER J SHOT J button. Player 1 Joystick Player 1 Start . To return to the test menu, push the PLAYER 7 START and PLAYER I SHOT J buttons simultaneously. . The test menu will always return to the screen:

  • After you exit the “7, CONFIGURATION Player 1 Shot1 Player 1 Shot 2 MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.
  • TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved. OUTPUT Used to test the coin meter and the coin lock. SOUND & VOICE Select a code of SOUND or VOICE with the PLAYER / JOYSTICK. Push the PLAYER ! SHOT I _ button to hear the sound of the selected code. COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background. DOT CROSS HATCH _| Used to test the screen size, focus and distortion. GAME DATA Coin meter and Free play information will be displayed. CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section. MEMORY CHECK Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If“NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears. EXIT Select this item and push the PLAYER J SHOT J button to return to game play mode. erg | 6 ‘Proprietary and confidential information, not to be disclosed or copied without the express permission of _CAPCOM® COIN-OP,

Page 12

CAP@ORI* coin-op, Inc. Super GEM Fighter ™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB.

The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

i. ACCESSING THE CONFIGURATION MENU

  • CONFIGURATION MENU + From the TEST MENU, move the arrow to > 1. SYSTEM “7, CONFIGURATION?” and push the PLAYER 1 SHOT I button. GAME The screen left will be displayed. A description of each option is DEFAULT : explained in the table below.

SAVE & EXIT

SELECT = 1PUPOR DOWN START = 1P SHOT1

  • CONFIGURATION MENU ITEM DESCRIPTIONS

| SYSTEM _| Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT | Use this item to restore configuration settings to the original factory values. Press the PLAYER ] SHOT 1 and PLAYER I SHOT 2 buttons at the same time to restore default values. Use this to save new configuration settings and exit to the Test Menu. The message “SAVING NEW CONFIGURATION IN EE-PROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu Teappears.

Proprietary and confidential information, not ta he disclosed or copied without the express permission of CAPCOM® COIN-OF, ING. 7

Page 13

QAP@OM’ coin-op, INC. Super GEM Fighter™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM

7-1. SYSTEM CONFIGURATION — , CONFIGURATION SETTINGS

COIN MODE2COIN1CREDITMove the PLAYER J JOYSTICK up or down to
Coneonhighlight the desired option.Once the option is

highlighted, move the PLAYER | JOYSTICK left or

MONITORNORMALright or press the PLAYER 1 SHOT J button to select.

DEMO SOUND ON

SOUND MODE STEREO (QSOUND}

CHUTE TYPE 2 CHUTES SINGLE

  • EXIT

SELECT OPTION P UP OR DOWN MODIFY SETTING = 1P LEFT OR RIGHT P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE SELECT THE CHARGE PER PLAY.
  • CONTINUE SELECT ON FOR CONTINUOUS PLAY OR OFF FOR NON-CONTINUOUS PLAY.
  • MONITOR FLIPS THE POSITION OF THE SCREEN. IF THE SCREEN APPEARS UPSIDE-DOWN, CHANGE THE SETTING TO FLIP; IF THE SCREEN APPEARS CORRECT, SELECT NORMAL,
  • DEMO SOUND _| TURNS ATTRACT SOUNDS ON OR OFF.
  • SOUND SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET. NOTE: STEREO SHOULD MODE ONLY BE SELECTED FOR USE WITH CAPCOM® QSOUND CABINETS.
  • CHUTE TYPE _| SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTE TYPE.
  • EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH EITHER THE PLAYER ] SHOT I BUTTON OR THE PLAYER I SHOT 2 BUTTON. |

SYSTEM CONFIGURATION OPTION SETTINGS

  • COIN MODE 1 COIN 1 COIN 1 COIN 1 COIN
2 CREDITS3 CREDITS4 CREDITS5 CREDITS
1 COIN1 COIN1 COIN1 COIN2.COINS
6 CREDITS7 CREDITS8 CREDITS9 CREDITS1CREDIT
3 COINS6 COINS7 COINS
1 CREDIT1 CREDIT1 CREDIT

8 COINS 2 COINS START FREE PLAY 1 CREDIT 1 COIN CONTINUE ON OFF

NORMAL FLIP OFF 00: MONAURAL SHU’ LE 2 CHUTES MULTI 1 CHUTE SINGLE

8 Proprietary and confidential information, not to be disclosed or copied without the express permission af CAPCOM® COIN-OP,

Page 14

QAPEEM coin-op, inc. Super GEM Fighter ™

GAME CONFIGURATION

7-2. GAME CONFIGURATION CHANGING THE GAME CONFIGURATION

SETTINGS DIFFICULTY NORMAL

DAMAGE LEVELNORMALMove the PLAYER I JOYSTICK up or down to
TIMER SPEEDNORMALhighlight the desired option.Once the option is

highlighted, move the PLAYER J JOYSTICK left or

GAME SPEEDFREE SELECTright or press the PLAYER J SHOT ! button to select.

MAX ROUND 1 ROUND

EVENT OFF

JOIN-IN ON

EXIT 1.

2.

3.

4.

5.

6.

7.

8.

SELECT OPTION = 1P UP OR DOWN MODIFY SETTINGS =4P LEFT OR RIGHT 1P SHOT1 OR SHO

DESCRIPTION OPTION SETTINGS

NORMAL HARD 4

  • DAMAGE SETS THE OFFENSIVE POWER LEVEL. NORMAL: LEVEL SETS THE SPEED OF COUNTDOWN FROM THE TIMER NORMAL DISPLAY.

SET THE GAME SPEED. “TURBO 1” AND “TURBO 2” ALLOWS THE OPERATOR TO SET THE GAME SPEED.

“FREE SELECT” ALLOW THE PLAYER SELECT THE GAME SPEED USED TO SET THE NUMBER OF ROUNDS PER MATCH,

  • EVENT SPECIAL SETTING FOR TOURNAMENT EVENT 1 MATCH: ONLY ONE CREDIT IS REQUIRED FOR A 2P GAME. THE GAME ENDS AFTER ONE MATCH REGARDLESS OF THE RESULT..
  • JOIN-IN SET THE OPTION TO ALLOW OTHER PLAYERS TOT JOIN-IN. RETURN TO THE CONFIGURATION MENU.
NOTE:

mation, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. 9

ee

Page 15

CAPQOM" co-op, inc. _ Super GEM Fighter™

JAMMA Connections

.C.

VIDEO SYNC SERVICE (FREE CREDIT) NIC 2PLAYER - COIN 2PLAYER -START 2PLAYER - UP 2PLAYER -DOWN

GND. GND. VDC C.

vi

® c.

VIDEO BLUE. VIDEO GROUND DIAGNOSTICS LPLAYER -COIN

1PLAYER -DOWN 1PLAYER - LEFT

VC IND ‘ND

WIRE COLOR CONNECTOR ODD ROW CONNECTOR EVEN ROW ‘WIRE COLOR

NIC

NIC NIC PURPLE/YELLOW_| NOT USED NC NIC PINK NOT USED RED NOT USED. BLUE NOTUSED a GRAYIVELLOW | NOT USED : a PINKIYELLOW | NOT USED oe NIC NIC 2 NC NIC NIC NIC NIC NC GRAYNVELLOW _| TEST BRKT-VOLUME UP } BLACKMWHITE __| TEST BRKT-VOLUME COMMON [ae PLAYER 2 KICK - COMMON 33 PLAYER 1 KICK-COMMON BLACK

10 Proprietary and confidential information, oot to be disclesed or copied without the express permission of CAPCOM® COIN-OP,

Page 16

co GAPCEN” com-op, inc. Super GEM Fighter™

REFERENCE INFORMATION

GAME CASE CONTROLS

COIN REGISTER . METER (NOTUSED) COMMUNICATION (NOT USED) PORTS (NOT USED) OUT IN

*VOLUME UP

*VOLUME DOWN

JAMMA AUXILIARY CABLE AUDIO OUT (FOR Q SOUND) CONNECTOR CONNECTOR RIGHT: RED, LEFT: WHITE v300800

TYPICAL CONTROL PANEL LAYOUTS FOR “Super GEM Fighter™”

eee gy \ O06 eee “OO jese

Page 17

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal taw provides severe civil and criminal penalties for.the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminai copyright infringement.

AIP COM COIN-OP, INC. 475 Oakmead Parkway Sunnyvale, CA 94086 Phone: (408) 774-0500 Fax: (408) 522-5331

Copyright © 1997 CAPCOM ® coin-op, inc., All Rights Reserved