OutRun Mini Manual 90500010
Out Run (Mega-Tech, SMS based) (Sega, 1987) · Manual · 41 pages · 16 sections · original scan
MINI UPRIGHT
OWNER’S MANUAL
TABLE OF CONTENTS
INTRODUCTION OF THE OWNER’S MANUAL
- HANDLING PRECAUTIONS
- PREVENTION OF COUNTERFEITING AND CONVERSION
3, PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
- NAME OF PARTS 1
NAME OF PARTS 2
- ADJUSTMENT OF THE SERVICE SWITCH
- INSTRUCTION OF BOARD AND CONNECTORS
- DISASSEMBLING AND ADJUSTING THE HANDLE UNIT 8, DISASSEMBLING AND ADJUSTING THE ACCELERATOR AND BRAKE oe soe ie
- DIP SWITCH SETTING
- ERROM/ROM LOCATIONS ~ eoreannune
11, SELF~TESTING 14~20
12, PARTS LIST «= 21~39
13, WIRING DL 0
MINI_ UPRIGHT TYPE
SPECIFICATIONS INSTALLATION SPACE + 50 mm (21.7 in.) W x 830 mm (32.7 in.) D HEIGHT + 1650 mm (65 in.) POWER 2165 W CRT. 2 207 WEIGHT +96 kg (212 Ibs. )
© Descriptions herein contained may be subject to improvement changes without notice.
INTRODUCTION OF THE OWNER'S MANUAL
SEGA ENTERPRISES, LTD., supported by its high electronic technology of LSIs, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OwNER'S manual is intended to provide detailed comments together with all the necessary information covering the operation in general of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the OUT RUN,
a new SEGA product. The manual is intended for those who have knowledge of electricity and technical expertise especially in ICs, CRTs, microprocessors, etc. Carefully read so as to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no
circumstance touch the interior system.
1, HANDLING PRECAUTIONS
When installing or inspecting, be very careful of the following points and pay attention to ensure that the player
can enjoy the game safely.
© Be sure to turn the power off before working on the machine. © To insert or pull out the plug quickly is dangerous. © Itis necessary to make sure that the power cord or the grounding wire is not exposed on the road, etc. in a manner 80 as to be dangerous. Make sure that grounding connections are made safely at the position where so specified. © Do not use any fuse that does not meet the specified rating. © Make complete connections for the IC board and other connecters. Insufficient insertion is very dangerous.
Also, for the IC board circuit inspections, only the logic tone is allowed. The use of a tester is not permitted, so be careful in this regard. After confirming that there are no irregularities, turn the power ON.
2 PREVENTION OF COUNTERFEITING AND CONVERSION
LABELLING
To prevent counterfeits and conversions, the following labels are put on all the SEGA products. When handling such goods, be sure to confirm the labels. They are used to Prevent illegal acts such as the unauthorized copying of the Products and the printed circuit boards thereof or carrying on business by manufacturing similar mercnandise or by converting, selling or using such products or printed circuit boards.
ORIGINAL SEAL Lic E SEAL
The following seal is put on The following seal is put on the the machines manufactured by kits, such as the printed SEGA. circuit boards, of SEGA
products.
COPYRIGHT NOTICE
This SEGA product has the copyright notice as follows:
© SEGA 1986
This signifies that this work was disclosed in 1986 and is the Property of SEGA ENTERPRISES, LTD.
PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
The OUT RUN is an indoor game machine. Absolutely do not install it outside. Even indoors, avoid installing in places mentioned below so as to ensure proper usage:
Places subject to rain or water leakage, or condensation due to humidity. In the proximity of an indoor swimming pool and/or shower. Places subject to direct sunlight. Places subject to heat sources from heating units, etc., or hot air.
Vicinity of highly inflammable/volatile chemicals or hazardous matter.
Sloped surfaces. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. Places subject to any type of violent impact. Dusty places.
- NAME OF PARTS 1 PLAY INET PLATE
422-0172
DESIGN PLATE
423-0036
20" MONITOR
winpow
ASSY SHIFT LEVER CABINET = KR=13001
ASSY CONTROL PANEL, KR=11005
COIN CHUTE DOOR
ASSY ACCEL & BRAKE CASHBOX DOOR KR— 12002
(TAMPERPROOF WRENCH) TAMPERPROOF WRENCH)
M4540 0006-01 M5 _540-0007-01 M6 540-0015-01 M8 _540- 0009-01 M4 540-0018 M5 540-0017
x
- NAME OF PARTS 2
ASSY SOLENOID KR-0015, :
SPEAKER GAME BOARD
834 6065-02 834-6065-04
SERVICE SW
ASSY POWER SU
- ADJUSTM! sw INT OF THE SERV!
The layout as shown below can be viewed by opening the coin
chute door.
@® service swrren TEST SWITCH (@) DEMAGNETVING COIN CHUTE DOOR SWITCH
CASHBOX POTENTIOMETE
OPERATING INSTRUCTIONS
@ DEMAGNETIZING SW on-screen color
@ service swrrcu » of servicing and
s without
(this allows ing on the m
you to check the game). Q@ esr swrrcn... For operating this switch, see SELF~ @ Porentiomerer ApsustT
INSTRUCTION OF BOARD AND CONNECTORS,
[POTENTIOMETER GROUP] 20P
(120 GROUP) sop
[PO THE SPEAKER | 4P
[70 THE MONITOR | 6P
10P
TO THE POWER SUPPLY
Ws IBLING AND ADJUSTING THE HANDLE UNIT
MPERPROOF SCREW M6 To open the dashboard, take off the 3 M6 TAMPERPROOF screws.
After doing this, spring replacements and steering adjustments can be made
DASHBOARD
ADJUSTMENT SCREW
POTENTIOMETER BRACKET D Release the 2 adjusting screws of the potentiometer bracket and perform the necessary adjustments by changing its gear position, making sure that the variable is within the allowable extent as shown below, and then retighten the adjusting screw.
ZPOTENTIOMETER
Standard value v iH] > 7CH 70H 7EH 7FH 80H 81H 82H 83H 84H] yon,
—=— Allowable adjustment range —= Minimum (33)
8, DISASSEMBLING AND ADJUSTING THE ACC! AND BRAKE LERATOR
TAMPE: ROOF SCREW (M
ACCELERATOR “BRAKE UNIT
ACCELERATOR ACCELERATOR BRACKET GEAR BRAKE GEAR
BRAKE POTENTIOMETER
ADJUSTMENT SCREW B. ADJUSTMENT SCREW
BRAKE BRACKET
) Display the SELF-TES'
Roleate the: adjoskmant:.sdiewsy move the Hix!
adjustments so that the variable becomes 20H when the
accelerator/brake is released and returns to its original
position.
- Even after the al s been followed, if the
variable is not within the allowable range, then slightly turn
the gear to make an adjustme:
ACCELERATOR
Minimum pales Maximum (fully open)
- . Ds) 1CH_1DH 1EH 1FH 20H 21H 22H 23H 24H| * Brake
- = Allowable adj
9. DIP SWITCH SETTING
| 4 COINS 3 CREO! =
[veom + cneorr |
| 2coms seneoirs [OFF OOM
- ERROM- ROM LOCATIONS.
GAME BD OUT RUN , .y. Sener (a te
w CPU BD OUT RUN 837~6063-02
1 (02)
=12-
‘ONE_TIME_ROM GAME BD | sor-enes-o1 | wea ‘CPU BD —| wt-eoa-o1| es -eaed=oF ie ice tama
- SAME AS THE PREVIOUS COLUMN.
Ps PROGRAM
11, SELF-TESTING
The main purposes of these tests are to check the operations of
the game boards, to find the defects if any, to adjust the monitor colors properly, and to make sure the sounds are produced satisfactorily. It is also performed to indicate the assignments of the dip switches, check bookkeeping functions,
etc.
KIND OF TESTS
- Memory Test:
- Input Test:
- Output Test:
- Motor Test:
- Sound Test:
- CRT Test:
- Dip Switch
Assignment:
- Bookkeepin:
- Backup RAM
Clear:
- EXIT To check the EPROM programs and the map area of the RAMs. To test the operation of the coin switch, shift lever, handle/accelerator, brake, start switch, service switch, etc. To test the operation of the lamps. Tests in this mode are not applicable for the type. To check the quality of the sounds produced by the PCB and the video disc, and to adjust the balance of the speakers. To check if the colors on the monitor are displayed correctly.
To indicate each dip switch assignment. To indicate information data on average score, average play time, etc.
When the power is turned off, a backup battery system automatically takes over, thus allowing the continuous storage of all bookkeeping data. Using this item will enable you to clear said data.
See page 20.
- TEST OPERATION
- Push the test switch and Fig. 1 will be shown on the
screen.
- Select CONTINUE or INDIVIDUAL by using the START button
bIAGNosTIC Conti J MEMORY TEST INPUT TI ourpur MOTOR SOUND TEST CRT TEST DIP sw. BOOKKE! BACKUP EXIT SELECT BY STEERING PUSH TEST BUTTON”
FIG.1
- Move the steering to bring the
arrow to the desired position. EST. TEST TEST
A :BPING RAM CLEAR
(CONTINUE):
© Bring the arrow sign to CONTINUE first, and move it to one of the
tests to start. Push the TEST
button, and the tests will be
performed in order, one by one,
starting from the test where the arrow was originally set to EXIT.
© If the START button is pushed when the
arrow is at CONTINUE, it will change
to INDIVIDUAL. Pushing it again returns it to CONTINUE.
(INDIVIDUAL):
0 If the arrow is at INDIVIDUAL first
and brought to a certain test which
you want to conduct, only that test is performed by pushing the TEST button.
- When each test is finished, push the TEST button, In the
case of CONTINUE, push the TEST button, and it will
automatically go into the following test. If the TEST button is pushed in the case of INDIVIDUAL, FIG. 1 is
shown. If you want to end the test mode at this time,
bring the arrow to EXIT and push the TEST button again,
and it will return to the ADVERTISEMENT mode.
2, TEST LTEMS
- Memory Test:
DIAGNOSTIC MEMORY. TEST a ROMS TEST #*
cu ion ie 3 ee «87 «5 4% RAMS TEST
om cous 1c 129 0 KC ancl ie ce « cos ic 78
Indication of "GOOD" following the IC No. means the IC is all right. Push the TEST button to proceed to the following test item:
- Input Test
COIN st COIN #2 LOW GE:
foil aon) (=m zon)
- HANDLE + ACCELERATOR- > en oH ze re GOH) sm sent xy san ACH rH aH FH OH] 2m ze a amt Standard value Standard value
© Operate the dip switches. When "ON" is indicated at the right side of the corresponding item on the screen, it is OK.
o If the data value increases when pressure is applied to the accelerator's or brake's pedal, it tests out satisfactorily.
o When the tests are ended, push the TEST button.
- Output Test
DIAGNOSTIC OUTPUT TEST
START LAMP
- BRAKE LAMP
If the start LAMP lights up, it is functioning properly. Push the TEST button when the testing has been completed.
ange
- Sound test
DIAGNOSTIC SOUND TEST COIN IN 10. VOICE 1 . CHECK POINT 1. VOICE 2 |. SIGNAL 1 VOICE 3
SIGNAL 2 13. VOICE 4
- WAVE 15, CHEERS
- MUSIC 1 MUSIC 2 REBOUND MUSIC 3 SELECT BY STEERING PUSH START BUTTON’
When the test has been completed, push the TEST button.
- CRT, Test
DIAGNOSTIC weuios CRT. TEST creex \ COLOR BAR grower avve epee [Real re [7 [ane wre nay,
‘GRAY ‘Lack
CRT. POSITION CHECK
When the test has been completed, push the TEST button.
- DIP SWITCH ASSIGNMENTS
DIAGNosTIC
DIP SWITCH ASSIGNMENT 123 4 5 6 7 8 DIP SW.A OFF OFF OFF OFF OFF OFF OFF OFF __ DIP SW. OFF OFF OFF OFF OFF OFF OFF OFF Switches. A 1281 COIN SWs1.1 COIN 1 CREDIT. ____ Coin Suitch Setting. 5678 COIN SW221 COIN 1 CREDIT B 2
| 12 TYPE | MINI UP | ovine Tere | |
| 3 ADVERTISE SOUND | ON | “| | oer |
| 56 TIME ADJ. | /NoRMAL. | Sor ust |
78 NUMBER OF ENEMY NORMAL.
‘Adjustment of the game tine.
The appearance frequency of the other 4
rane oe owe Sete Tanase ot ate eter
- Bookkeeping
GNOSTIC BOOKKEEPING
COIN CHUTE #1 COIN CHUTE #2 Usage frequency of coin chute 1 Usage frequency of coin chute 2 COIN CREDIT —Wunber of coin credits SERVICE CREDIT — Usage frequency of service sviten TOTAL CREDIT umber of credits TOTAL TIME OH [IM Os ond) PUSH START BUTTON ! Operating time (hour-minute:
Only the data that falls within the range of up to 999H 59M 59S can be memorized.
The above screen indication is for testing. When the tests are finished, push the START button and the following will be shown:
AGNOSTIC BOOKKEEPING
NUMBER OF GAME AVE. SCORE ‘VOR-SCORE LOW -SCORE ++ GAME TIME ++
TOTAL On
AVERAGE On
LONGEST On
PUSH START BUTTON !
Every time the START outton is pressed, the bookkeeping test
display is repeated.
oWhen the tests are ended, push the TEST button.
- Backup RAM Clear: To clear the data, bring the arrow to "YES" and push the
TEST button.
DIAGNosTIC
BACKUP RAM CLEAR
No YES
SELECT BY STEERING PUSH TEST BUTTON /
When the test is finished, push the TEST button to end the
test (in the case of “INDIVIDUAL,” however, the test mode
returns to Fig. 1 first).
- EXIT In the state as shown in Fig. 1, operate the steering to bring the arrow to EXIT and push the TEST button. The self-
testing will then end and return to the ADVERTISEMENT mode.
12, PARTS LIST (O) TOP ASSY OUT RUN MINI U/R (KR—00005) (0-1/2)
@® TOP ASSY OUT RUN MINI U/R (KR-00005) (0-2/2)
ITEM NO. PART NO.
1 KR-10005 2 KR-11005 3 KR~12002 4 KR-0015
6 KR-0013 1 KR-1071 8 KR-1073 fy /834-6065-02,08 10 1979 u ‘s0027XY 2 421-6412 13 421-$800-45 “ 5 ‘son07¥ 16 82789 932-05, ra 3602 8 ‘so198y 19 ‘89618X » SGB-1035x. 2 SGM-2675 2 SGM-1964
Pa 422-0172-01 % KR-1111X 220-5130 540-0006-01 540-0007-01 540-0015-01
101 e1-0769 201 000-0414-8. m2 (000-0510-S 203 000-0516-FS 20 (000-0520-8 205 (000-0530 206 005~3113-F 207 030-0520, 208 (008-0520 209 ‘008-0535 210 ‘010-0310-F an ‘029-0082 a2 (046-0001, 213 (051-0005 a4 (060-0006 215 (065-0008, 216 (069-0001, 217 060-0005 218 061-0005, a7 (060-0005 218 061-0005, DESCRIPTION
ASSY CABINET MINI U/R ASSY CONT PANEL MINI ASSY ACCEL & BRAKE U/R ASSY SOLENOID ASSY PWR SPLY MINI U/R LOCAL SHIELD BASE ACCEL & BRAKE PEDAL SHAFT GAME BD OUT RUN STICKER SERVICE INSTR NAMEPLATE ELEC SPEC ADJUST INSTR SHEET OUT RUN ORIGINAL SEAL OUT RUN OWNER'S MANUAL OUT RUN MINI U/R STICKER SEGA INFORMATION STICKER DANGER HIGH VOLTAGE SEGA OUT RUN MINI U/R STICKER SERIAL NO. INFORMATION STICKER POSSESSION STICKER BUSINESS INFORMATION KEY BAG POLYETHYLENE BAG 240«370 POLYETHYLENE COVER 650%1500x880 DENOMINATION SHEET DENOMINATION SHEET PLAY INSTR PLATE OUT RUN MINI U/R ASSY CLR DSPL. 20 TYPE
EXT SPRING
- VOL CONT B.SK OHM WRENCH FOR TAMP SCR M4 WRENCH FOR TAMP SCR MS WRENCH FOR TAMP TYPE M6
STAPLE MAX #3,
M SCR PH W/S Moxa M SCR PH W/S M5x10 M SCR PH W/FS Msx16 M SCR PH W/S M5x20 M SCR PH M5x30 W SCR PH W/F 21x13, HEX BOLT Msx20 ‘TMP PRF SCR TH MS5x20 ‘TMP PRF SCR TH M5xa5, S-TITE SCR PH W/F M3x10 ‘TMP PRF SCR BH Mé6x14 SCR NAIL THH 1.5<16 FLG NUT Ms. FLT WSHR M6 E RING 4mm FLT WSHR 5.5-20%1.6 FLT WSHR Ms SPR WSHR Ms. FLT WASHER Ms SPRING WASHER Ms % Note: VOL CONT refers to the Potentiometer.
@ ASSY CABINET MINI U/R (KR-10005) (0-1/3)
@ _ASSY CABINET MINI U/R (KR-10005) (0-2/3)
ITEM NO,
eerecsene
8 SSek8e8 AB-1151Y AB-1206 MO-1215Y RA-1016
000-0108-FS 000-0116-$ 051-0008 005-3113-F 006-3110 010-0408-F 029-0021, 031-0425-B
SGB-3774-2 211-0118 209-0023 280-5015 SGB-3774-5 ‘211-0080 2u1-0117 211-0085 00-5133 209-0082 SGB-3774-8 211-5105 211-0014 211-0080 211-0081 211-02 au 211-0121 2n1-o116 DESCRIPTION
ASSY SUB CABINET MINI MASK BOARD HOLDER LOWER WINDOW GLASS. DESIGN PLATE OUT RUN MINI HOLDER UPPER SW UNIT TV MASK GRAY SMOKE TV MASK COVER METER BRKT BRKT MAIN SW CABLE & PLUG ASSY (USA ONLY ) CABLE & PLUG ASSY ( 200~240V ) STICKER COIN METER STICKER EARTH STICKER DANGER HIGH VOLTAGE STICKER MAIN SW PUSH ON PUSH OFF HARNESS LUG
MAG CNTR 6DIG DCsv ‘TERM BINDING POST BSING STRAIN RELIFE 8.3 CORD CLAMP 10 SW PB TYPE ‘SW STOPPER «712 CORD CLAMP 15
M SCR PH W/FS Maxa. M SCR PH W/S Maxis FLNG NUT Ma W SCR RH W/F 3.113 W SCR FH 3.1x10 S-TITE SCR Mix8 M SCR TH BLK Max18 CRG BLT BLK Max25
WIRE HARN AC CONN CAP AMP 3P CONN CLOSED END FASTON RCPT 187 WIRE HARN EXT AC 100 CONN CAP-AMP 2? BROWN CONN CAP AMP 2P YELLOW CONN PLUG AMP 2P BROW CABLE & CONN 3001. CONN CLOSED END WIRE HARN 50? CONN FEM soP CONN CAP AMP 2P WHITE CONN CAP AMP 2P BROWN CONN CAP AMP 3P BROWN CONN CAP AMP 4P WHITE, CONN CAP AMP 4P BROWN CONN CAP AMP 4P RED CONN CAP AMP 2P ORANGE
@ ASSY CABINET MINI
ITEM NO. PART NO.
308 211-0102 270-5016 ‘SGB-3774-9 211-5088. 211-0060 211-0046 270-5016 SGB-3774-10 211-0044 211-0060 212-5034 270-5016 SGB-3774-13 ‘210-0087 209-0023 SGB-3774-15 211-0167 211-0041 211-0012 211-0005 211-5047 01-0460 U/R (KR-10005) (D-3/3)
DESCRIPTION
CONN PLUG AMP 4P YELLOW FERRITE SLEEVE CORE WIRE HARN 20P CONN FEM 20P CONN CAP AMP 3P WHITE CONN CAP AMP 6P WHITE FERRITE SLEEVE CORE WIRE HARN RGB CONN CAP AMP 2P WHITE, CONN CAP AMP 3P WHITE CONN FEM 6P FERRITE SLEEVE CORE WIRE HARN COIN METER CONN PLUG AMP 4P BROWN CONN CLOSED END WIRE HARN EARTH TERM LUG RND 1D5 CONN PIN AMP CONN SOCKET AMP CONN CRIMP LOCK CONTACT PLASTIC TIE BELT 85mm
@ ASSY SUBCABINET MINI U/R (KR-1800) (0-1/3)
® ASSY SUBCABINET MINI U/R (KR-1800) (0-2/3)
ITEM NO.
SESSEEES
a4 PART NO.
KR-1801 KR-1802 KR~1803 KR~1804 KR~1805 TA-1010 RA~1007, RA~1008 RA-1009 AN-
601-0455 105-5038, HN-1050 MO=1008, PT-o342 109-0045 Dp-1148X KR-1810 KR-1810 KR-1811 KR-1812
(000-0106-8 (000-0408-S (000-0520-8 (005-3516-F (008-0416 (046-0001, 059-0007 031-0125-B 051-0004 005-3113-F (000-0310-FS. 244-098 (000-0516-S 031~0525-B 051-0005, DESCRIPTION
WOODEN CABINET MINI U/R. BACK DOOR, BRACKET FLOOR MAT SUPPORTER HINGE 148 COVER CASHBOX CASHBOX LOCK BRACKET GUARD PLATE LEG ADJUSTER BRKT TING LKG COVER PLATE LOCK RETAINER
LEG ADJUSTER STOPPER SPACER RING FAN BRACKET A AIR VENT KEY HOLDER LKG TNG PROTECTOR A PROTECTOR B BRACKET A BRACKET B
SPEAKER 8 OHM 120 AXIAL FLOW FAN AC
M SCR PH W/S Max6 M SCR PH W/S Moxa M SCR PH W/S M5x20 W SCR RH W/F 3.5x1 TMP PRF SCR TH Maxis SCR NAIL TH STAINLESS 1.516 HEX NUT 9/8-16 CRG BLT BLK Max25 FLG NUT Ma W SCR RH W/F 31x13 ‘ M SCR PH W/FS M3x10 DOUBLE FACE TAPE 10mmx50m/ROLL M SCR PH W/S M5x16 CRG BLT BLK M5x25 FLG NUT M5,
(©) ASSY SUBCABINET MINI U/R (KR-1800) (D-3/3)
ITEM NO.
ao. PART NO.
SGB-3774-6 211-0087 SGB-3774-14 DESCRIPTION
WIRE HARN SPKR CONN PLUG AMP 4P BROWN WIRE HARN COIN SW CONN PLUG AMP 4P WHITE WIRE HARN FAN MOTOR CONN PLUG AMP 2? BROWN CONN PIN AMP FASTON RCPT 187 FASTON RCPT 205 PLASTIC TIE BELT 85mm HARNESS LUG.
@ ASSY CONTROL PANEL MINI U/R (KR-11005) (D-1/3)
@ ASSY CONTROL PANEL MINI U/R (KR-11005) (0-2/3)
SSSSSBRSRREeS
SRS885 PART NO.
117-5133 KR-1165,
100-5015, 100-5035 220-5130 500-5053 280-0248 280-0425
000-0408-FS (000-0510-FS (008-0410 ‘008-0425 ‘010-0308-F (028-0007 (028-0010 (028-0014, (029-0078 (030-085 (054-0005 (060-0005, (060-0008 DESCRIPTION
CONTROL PANEL BASE CONTROL PANEL COMPRESSION SPRING HANDLE BASE STEERING WHEEL SHAFT SHAFT ‘ARM PLATE ARM BAR STEERING WHEEL STOPPER EXTENSION SPRING. VOLUME BRACKET BUMPER BRACKET BUMPER STOPPER
COLLAR B SPACER A STEERING HANDLE ©270 KEY A KEY B HANDLE EMBLEM GEAR A GEAR B GEAR C GEAR D CAP NUT STOPPER WASHER STOPPER COLLAR SPACER WASHER B ASSY SHIFT LEVER S START PLATE SPACER
BEARING 10 BEARING 920 VOL CONT B-sk OHM PUSH BTN SWIT GREEN W/LAMP CLAMP CORD PLASTIC ID 8mm CORD CLAMP #10
M SCR PH W/FS Maxe M SCK PH W/FS M5x10 TMP PRF SCR TH Maxi TMP PRE SCR TH Max25 S-TITE SCR PH W/P Max8 SET SCR HEX SKT CP UNBR Max10 ‘SET SCR HEX SKT CP M5x8. SET SCR HEX SKT CP UNBR Moxa ‘TMP PRF SCR BH Méx14 HEX BLT Max25 U NUT Ms FLT WSHR Ms FLT WSHR Ms
@ ASSY CONTROL PANEL MINI U/R (KR-11005) (0-3/3)
ITEM NO.
so PART NO.
061-0006, 061-0008 061-0010 (069-0009 (069-0022 (069-0054 050-0010
SGB-3774-11 211-0059 SGB-3774-12 211-0100 211-0081 ‘601-0460 280-0472 DESCRIPTION
SPR WSHR M6 SPR WSHR SPR WSHR M10 FLT WSHR 10.5-28%2 PLT WSHR 5.5-14x1 E RING 15mm HEX NUT Mio
WIRE HARN HANDLE. CONN PLUG AMP 3P WHITE WIRE HARN START SW CONN PLUG AMP 4P RED CONN PIN AMP. PLASTIC TIE BELT 8mm z FASTON RCPT 110
© ASSY ACCEL & BRAKE U/R (KR-12002) (0-1/2)
© ASSY ACCEL & BRAKE U/R (KR-12002) (0-2/2)
ITEM NO.
SSeeSeee8 PART NO.
KR-1216 KR-1217 KR-1218 KR-1219 KR~1220 KR-1221 KR-1222x. KR-1223, KR-1224 KR-1225 KR-1205, KR-1208 KR-1209 KR-1210 KR-1211 KR-1213 ‘SGB-3751-12 211-0045
220-5130 DESCRIPTION
up PEDAL BRACKET STOPPER BRACKET ACCEL BAR. BRAKE BAR AND PEDAL BUMPER BRACKET A BUMPER BRACKET B BUMPER A BUMPER B ‘SPRING STOPPER VR BRACKET SHAFT BRAKE ACCEL COLLAR TORSION SPRING A TORSION SPRING B BUMPER. WIRE HARN ACCEL & BRAKE VR CONN PLUG AMP 6P WHITE,
VOL CONT B-SKOHM GEAR 15 66 GEAR V6 CONN PIN AMP. CORD CLAMP 15 TIE BELT
M SCR PH W/S Max6. M SCR FR W/S Mix M SCR PH W/FS Max8 M SCR PH W/PS M5x10 SET SCR PH SPCL Msx6 CRG BLT BLK M5<14 HEX NUT Ms FLG NUT Ms
FLT WSHR Ms
SPR WSHR FLT WSHR 5.5-14%1
© ASSY SHIFT LEVERS (KR—13001) (0-1/2)
ASSY SHIFT LEVERS (KR-13001) (0-2/2)
ITEM NO.
S8S8288 PART NO.
KR-1312, KR-1314 KR-1303, KR-1320 KR-1304 KR-I315 SGB-3740-5 211-0043 280-5015 KR-1316 KR-1318,
211-0001 101-5008 509-5088 310-0012 uT-o141
(069-0005, DESCRIPTION
SHIFT BRACKET B COVER BRACKET B STOPPER ‘COMPRESSION SPRING SHAFT ‘SUB ASSY SHIFT LEVER WIRE HARN SHIFT SW CONN PLUG AMP 2? WHITE PASTON RCPT 187 SPACER MOUNT BRACKET
CONN PIN AMP STEEL BALL #87312 ‘SW MICRO TYPE PAPER INSULATOR LOCK PLATE.
FLT WSHR SPECIAL 8.3-14.3%0.5 M SCR PH W/FS Maxs NYLON WASHER SPECIAL 85-141 M SCR PH Max16 FLT WSHR 4.4-161.6 E RING 6mm Ma U NUT. S-TITE SCR PH W/F Max8,
@ ASSY SOLENOID
(KR 0015;
@ ASSY SOLENOID (KR-0015) (0-2/2)
ITEM NO. PART NO. DESCRIPTION
| 1 | KR-0016 | BASE A |
| 2 | KR-0017 | BASE B |
| 3 | KR-0018 | BRACKET A |
| 4 | KR-0019 | BRACKET B |
| 5 | KR-0025, | SPACER TUBE A |
| 6 | KR-0026, | SPACER TUBE B |
| 7 | KR-00z7 | BUMPER |
| 8 | KR-0028 | EXTENSION SPRING |
| 101 | 124-5013, | SOLENOID AC 100V 1.5kg |
| 102 | 280-5078 | RUBBER GROMMET 8x2 14x8 |
| 108 | 280-0100 | CLAMP CORD PLASTIC 5mm LD. |
| 201 | 000-0112-8 | M SCR PH W/S Moxi2 |
| 202 | 000-0112-FS_ | MCR PH W/FS Maxi2 |
| 205 | 000-04116-8 | M SCR PH W/S Maxi6 |
| 20 | 000-0435 | M SCR PH Max35 |
| 205 | 000-0140 | M SCR PH Maxdo |
| 206 | 010-0908-F | ——-S-TITE SCR PH W/F Max |
| 207 | 051-0008 | U NUT Mé |
| 208 | 060-0004 | FLT NUT Ma |
| 209 | 069-0007 | FLT WSHR 4.4-16.1.6 |
| 210 | 2-014 | GLUE SCREW LOCK |
| sor | SGB-3774-3 | WIRE HARN SOLENOID |
211-0098 CONN PLUG AMP 2P RED. 211-0041, CONN PIN AMP
(0-1/2) ASSY PWR SPLY MINI U/R LOCAL
GOO
ASSY PWR SPLY MINI U/R LOCAL (D-2/2)
ITEM NO.
S8Seses PART NO.
HN-4004 839-0085,
421-6503, 834-5635,
117-0184 17-5131 150-0285, 400-5055 481-0157 514-0064 514-0065, 514-0010 514-0084 514-0081 eo1-0129 280-0419 601-0769, 1-0160
(000-0414-FS 005-3110 (005-3113-F 005-3120
SGB~374-1 211-0097 211-0080 211-0082 211-0060 211-0123, 211-0115, 211~0005, 211-0085, 211-5076 212-5034 212-5067 212-5101 ‘270-5016 211-0167 211-0041 211-0042 211-0005, 211-5047 280-5015 280-0472 DESCRIPTION
BASE PWR AMP DC 12 10W PWR XFMR 90-240V 100V 2A 11V 5A. STICKER FUSE INSTR ASSY SSR BOARD TERMINAL PLATE IL 4P TERMINAL PLATE SP CAP E 22000MF 25V C-TYPE SW REGU 90-240V SV 10A DIODE BRIDGE SsVB20 FU HLDR 2P W/COVER FU HLDR 1P W/COVER FU 4A 6.4x30mm FU 5A 6.4x30mm FU 6A 6.4%301 NOISE FILTR AC 250V 4A HARNESS LUG STAPLE MAX #3 PLASTIC TIE BELT 85mm
M SCR PH W/FS Maxis W SCR RH 3.1x10 W SCR RH W/F 3.1x13 W SCR RH 3.1x20
WIRE HARN PWR SPLY CONN PLUG AMP 3P RED CONN CAP AMP 2P BROWN CONN CAP AMP 4P BROWN CONN CAP AMP 3P WHITE CONN CAP AMP 4P YELLOW CONN CAP AMP 2P RED CONN PLUG AMP 2P ORANGE CONN PLUG AMP 2P BROWN CONN FEM 4P CONN FEM 6P CONN FEM 8P CONN FEM 10P FERRITE SLEEVE CORE TERMINAL LUG ROUND IDs CONN PIN AMP CONN SOCKET AMP CONN CRIMP LOCK CONTACT FASTON RCRT 187 FASTON RCRT 110
P -& ive
ASSEMBLED BY: BRENT LEISURE LTD., UNIT 1, BRENT CRESCENT,
NORTH CIRCULAR ROAD, 3
LONDON NW10 OT, ENGLAND. FOR:
SEGA ENTERPRISES, LTD. No. 2-12, Haneda 1-chome ‘Ohta-ku, Tokyo 144, Japan oTel. + (03) 743 ~ 7438 OFAX: (03) 743 ~ 5599 .
OTLX : J22357 SEGASTAR
© SEGA 1986 4