CATHODE RAY TOMES

Perfect Billiards

Perfect Billiards (Nihon Systems Inc. (Japan), 1987) · Document · 8 pages · 14 sections · original scan

Page 1

INSTRUCTION MANUAL

_ BILLIARDS

ALL AMERICAN RIGHTS HELO BY: UNITED ARTISTS THEATRE AMUSEMENTS PALM SPRINGS, CALIFORNIA LICENSED FROM NIHON SYSTEMS INC., JAPAN ALL RIGHTS RESERVED ©1987

DISTRIBUTED EXCLUSIVELY BY

gi a5 AMUSEMENTS z 5 f 1975 RIVERSIDE DRIVE = LOS ANGELES, CA 90039 1 800 722 8258

Page 2

KIT CONTENTS

  • PERFECT BILLIARDS PC BOARD
  • PERFECT BILLTA MARQUEE SIGN a
  • PERFECT BILLIARDS MONITOR FLEXI » WIRE HARNESS S. CONTROL PANEL OVERLAY
  • CONTROL FANEL PLEXI
  • 8-WAY JOYSTICK
  • 4 BUTTONS WITH SWITCH ASSEMBLIES
  • INSTRUCTION LABELS 10, INSTRUCTION MANUAL

nit I ol \)

This equipment generates, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to subpart J of part 15 of F C. rules, which are designed to provide reasonable Protection against such interference. Operation of this equipment ina residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be necessary to correct the interference. WARN ING

Page 3

STEPS: 1. 2. 3. 4. 5. Remove Remove Remove Remove Remove

PREPARING THE CABINET

the old P.C. board the control panel the marquee sign front or side decals the old wire harness

Leave all the A.C. wiring to monitor, power supply, flourescent lamps, fuses, on/off switches, and transformer circuitry intact. Remove all remaining wiring from the cabinet.

Clean the cabinet thoroughly and repair any visible damage. Using a coat of paint on an older cabinet can restore a "like new" appearance. If needed, painting should be performed at this time.

A little extra time and effort spent now on enhancing a cabinet's appearance will definitely result in increased earning power later!

SUGGESTED CONTROL PANEL LAYOUT

O 8 WAY JOYSTICK O OO oO

O 2 PLAYERS

HORIZONTAL MONITOR MOUNTING © +5, +12, — VOLTS REQUIRED

Page 4

SPECIAL REQUIREMENTS

TV MONITOR:

This game is designed to be used with a

horizontally CX] vertically Cc]

mounted R.G.E. monitor, with the PCB as a negative polarity video and sink signals.

Your new game requires one sink wire connection called “composite sink". Tie the horizontal and vertical wires together, this signal is negative. Most monitors have supply positions for both negative and positive sink.

POWER SUPPLY:

The power supply requirements are as follows:

+5 VDC at 7 amps CX] +12 VDC at 1. amps Cx]

If the power supply in the game does not meet these requirements, it should be replaced prior to beginning the conversion procedures.

CONTROL, PANEL:

The control panel on the game to be converted can be either metal or wood. When selecting a game to convert consider the placement of joystick, push buttons and the monitor position.

Route the wires labeled control 1 (for upright) to your control panel. Cut this down to the required length. Strip and solder the wires to the joystick, and push buttons according to the pin-out assignments.

Page 5

MONITOR WIRING:

Route the wires labelled "VIDEO" or "MONITOR" up to your monitor and cut the excess wire. Refer to the pin-out assignment at the back of this manual for video outputs. The color code is as follows:

RED wire VIDEO RED GREEN wire VIDEO GREEN BLUE wire VIDEO BLUE BLACK wire VIDEO GROUND WHITE wire NEGATIVE COMP. SINK

comp sink [|

WELLS GARNER ELECTRO HOME -

Page 6

POWER SUPPLY WIRING:

Attach the wire harness connector to the main logic FCR. #** CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Double check that it is wired and connected properly. The label with the game name should face the component side of the PCR.

Separate the bundle of wires labeled "FOWER" and route them to your power supply. Strip about 1/2 " off the insulation and attach them to the power supply screws. The color code is:

RED wire # 18 + S vpc YELLOW wire # 18 + 12 VDC BLACK wire GROUND

NOTE: You can use the -3 VDC to power the lights to the coin door or the lighted push buttons.

COIN SWITCHES:

Most games have two coin outputs. Coin 1 must go to the N.QO. (normally open) terminal of the microswitch, (same as with coin 2) and a ground wire will go to the common terminal of the microswitch.

If you wish to use a coin meter for both coin mechanisms, connect only one coin output to both coin switches. This will save you the use of two coin meters.

COIN 1

GND

Page 7

PIN-OUT

DIP SW-1 OPTION SWITCH SETTING

DIP SW-2 COIN/CREDIT OPTION SWITCH SETTING

PRR Fi PaRRaF

ad ERerepeeeee Pe

DIP sw2

DIP SW1

MONITOR

HORIZONTAL

Page 8

PERFECT BILLIARDS

WIRE COL. PART SIDE o SOLDER SIDE WIRE COL. . GND BLACK

GND :

A3 § B3 + 5V wm ie}

+ 5V g +5V

YELLOW +12V +12V YELLOW

z a SPEAKER(+) SPEAKER(-) :

: COIN METER 1 COIN METER 2 Z

z i COIN SW2 WHITE

2P START YELLOW COIN SW1

ORANGE 1P START BLUE 1P UP WHITE 1P DOWN BROWN 41P LEFT RED 1P RIGHT

BEEBE HEBER e 5

= Ss 2P UP Fi

2P DOWN = a I

2P LEFT Aa AB

= z 1P SHOOT

>