Alpine Racer 2
Alpine Racer 2 (World, ARS2 Ver.B) (Namco, 1996) · Document · 45 pages · 15 sections · original scan
Operators Manual
IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY
AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY.
Part No. 90500094
GB) No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from NAMCO EUROPE LIMITED.
While the information contained in this manual is given in good faith and was accurate at the time of printing. NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
This machine has been manufactured in accordance with European Community Directives, and has been tested and complies with the Directives 89/336/EEC and 72/23/EEC by the application of EN55014-1, EN55014-2 and EN60335-1 standards and as such bears the C€ marking. Any changes or modifications to this machine must be in accordance with the European Directives. Any unauthorised changes to this product, may contravene such Directives.
Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients, some degradation of performance may occur. However the machine will recover normal performance once the source of the interference has ceased or been removed. Following abnormally high surges on the mains supply, the video monitor may need to be manualy reset by turing the machine OFF and back ON.
This game is not a machine as defined by the Machinery Directive 89/392/EEC
SAFETY WARNING
In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine.
Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work.
In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.
This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to the operating and service personnel at all times.
This machine is for indoor use only and should only be used for the purpose intended.
Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of this machine.
SAFETY NOTES
The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its, meaning before installing, servicing or making adjustments to this machine.
GENERAL SAFETY CONSIDERATIONS
Only operate this machine after checking that it has been installed correctly and in accordance with the manual
If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use.
Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.
For continued protection against fire hazard, replace fuses with the same type and rating. The use of other fuses or material is prohibited.
The power supply inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.
To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected EARTHED plug
If at any time the mains supply lead becomes damaged, it must be replaced immediately.
Do not turn the power switch ON until the machine has been installed correctly. OPP PEP BB BE & Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the correct fuses are fitted
Oo FP BP -
NOTES ON INSTALLATION ”)
NEVER turn the power to the machine ON until installation has been completed. an
In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug.
So that customers are not injured by the movement of the machine, ensure that there is as least 500mm separation between other machines or walls.
In order to avoid damage to the machine due to mis-operation, ensure Hr Y
that the voltage of the mains supply is 230volts AC. 7 Li, comme §| | fe: If the location of this machine has a polished floor, it is recommended KK that rubber pads are fitted under the level adjusters to prevent the NN Pp i Pl NM machine sliding on the floor. \X je: In order to gain access to the Power Supply and CPU assemblies, make \\ \\\ — sure that the rear of the machine is separated from a wall or other machine by at least 500mm.
> P&P BP EP Be
Va MOVING THE MACHINE.
This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.
The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is high, and it is important that a means of reaching the height safely,without stretching, is available. (e.g. Steps, Step Stool etc.)
The overall height of the machine, with the Header Assembly fitted, is 2050mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)
When moving the game, ensure that the game is dis-assembled into 3 parts: Monitor Assy, Coin Tower and Header Assy.
PRP & BP BP BP BB
Va REMOVING AND REPLACING PARTS Adjustments or maintenance on this machine should be carried out by suitably qualified personnel only.
Do not make any alteration to this machine without prior approval. Doing so could cause unforeseeable
Only parts specified by Namco Europe Ltd should be used when replacing or repairing parts. (Including screws).
Ensure that the power to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, repairs etc.)
If performing work not described in this manual, be sure to contact your distributor for instructions, as no responsibility will be accepted for damage or injury.
Parts of the Power Supply and Monitor remain hot and carry high voltage even after switching OFF and could cause burns or electric shock. Take care not to touch these parts accidentally.
Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors.
When removing the mains connector from the machine, or the mains plug from the wall outlet, always grasp the plug and not the cable.
Dieses Dokument dart in keiner Weise vervielfaltigt werden. Jegliche Tonaufnahmen sowie die Speicherung auf Datentrager (Suchsysteme), die Weitergabe oder sonstiges Kopieren flir den gewerblichen und privaten Gebrauch sind untersagt und bediirfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED.
Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behalt sich jedoch das Recht zu Anderungen ohne vorherige Bekanntgabe vor.
Dieses Gerat tragt das CE-Zeichen und wurde gemaB den EU-Richtlinien produziert. Es erfillt die Richtlinien 89/336/EEC und 72/23/EEC und Standards EN 55014, EN55104 und EN60335-1 (s. Deckblatt des Handbuches). Alle Verdnderungen an diesem Gerdt missen in Ubereinstimmung mit den EU-Richtlinien erfolgen. Nicht genehmigte Veranderungen an diesem Gerat verstoBen gegen diese Richtlinien.
Extreme AuBere Stérungen, wie z.B. durch Radiobetrieb, elektrostatische Entladung oder zeitweilige Netzschwankungen kénnen zu einer Leistungsminderung fahren. Sobald diese Faktoren jedoch ausgeschaltet oder beseitigt wurden, erreicht das Gerat seine normale Leistung.
Achtung! Falls der Spielprozessor auf Grund von Netzunterbrechungen oder Abnahme der Netzspannung aussetzt, kann es zum Verlust von Spielkrediten kommen.
Dieses Gerat fallt nicht unter die Maschinen-Richtlinie 89/392/EEC
SICHERHEITSHINWEISE
Um einen ordnungsgemaBen Betrieb dieses Gerdites zu gewahrleisten, muB vor Aufstellung, Inbetriebnahme und Gebrauch das Handbuch sorgfailtig gelesen werden. Sobald der Besitzer dieses Gerates die Demontage, Aufstellung, Inbetriepnahme oder den Service einer anderen Person Ubertragt, muB er sicherstellen, daB diese Person vor Arbeitsbeginn die nétigen Sicherheitshinweise und die dazugehérigen Kapitel des Handbuches liest und versteht. Um jegliche Unfalle wahrend des Betriebes zu vermeiden, miissen obige Hinweise strikt befolgt werden. Dieses Handbuch sowie das spezielle Gerite-Handbuch (wenn vorhanden) gehdren zum Gerdit und miissen dem Betreiber und Wartungspersonal stets zugéinglich sein. Dieses Gerat ist ausschlieBlich far den gewerblichen Gebrauch in geschlossenen Raumen bestimmt und darf nur dort betrieben werden. NAMCO LTD. dibernimmt keinerlei Haftung flr Unfalle, Verletzungen oder Beschadigungen, die auf nicht genehmigte Veréinderungen oder unsachgemaBen Betrieb des Gerdites zurtickzufuhren sind.
SICHERHEITSHINWEISE
Folgende Sicherheitsbegriffe werden im gesamten Handbuch benutzt. Machen Sie sich daher bitte vor Inbetriebnahme, Wartung und Durchtiihrung von Einstellungen am Gerat mit diesen Warnhinweisen vertraut.
WARNUNG /)\ WARNUNG bezeichnet eine Gefahrenquelle fur Leib und Leben. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.
VORSICHT (0) VORSICHT bezeichnet eine Gefahrenquelle fiir die Beschadigung des Gerates. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.
ALLGEMEINE SICHERHEITSHINWEISE
Das Gerat darf nur betrieben werden, nachdem es vorschriftsmaBig und in Ubereinstimmung mit dem Handbuch aufgestellt wurde.
Die Warnschilder miissen in gutem Zustand sein und ersetzt werden, wenn sie nicht mehr gut lesbar sind.
Bei Auftreten eines Fehlers oder Problems muB das Gerat sofort abgeschaltet werden und darf erst nach fachgerechter Behebung des Fehlers wieder in Betrieb genommen werden
Aufstellung, Service, Einstellungen und Wartung dirfen nur von dafur qualifiziertem Fachpersonal durchgefuhrt werden
Zur Vermeidung von Feuer, defekte Sicherungen nur durch vorgeschriebene Sicherungen ersetzen. Die Verwendung von andersartigen Sicherungen oder unterschiedlichem Material ist untersagt.
Das Netzteil im Monitor bleibt nach Ausschalten des Gerates noch heiB und fiihrt weiterhin Hochspannung. Daher besteht die Gefahr von Verbrennungen und Elektroschlagen. Diese Bereiche dirfen nicht beruhrt werden.
Zur Vermeidung von Elektroschlagen muB dieses Gerat mit einem ordnungsgemaB geerdeten Netzstecker versehen sein
Bei Beschadigungen des Netzteiles muB dieses umgehend ersetzt werden
Gerat erst nach abgeschlossener Aufstellung einschalten.
Vor Einstecken des Netzsteckers bitte sicherstellen, daB Netzspannung und Geratespannung Ubereinstimmen, und die vorgeschriebenen Sicherungen verwendet wurden. Ob BP BBP BB BBE
Oo FP BB
Hinweis:
Hinweis:
Ne HINWEISE ZUR AUFSTELLUNG
NIEMALS das Gerat einschalten bevor die Aufstellung véllig abgeschlossen ist. = =
Zur Vermeidung von Elektroschlagen muB das Gerat mit einem 5 ordnungsgema® geerdetem Netzstecker an die Stromversorgung angeschlossen werden.
Um zu vermeiden, daB Kunden durch die Geraétebewegungen A 5 verletzt werden, muB ein Sicherheitsabstand zu anderen Geraten 5
und Wanden von mindestens 50cm eingehalten werden. i"
}
Zur Vermeidung von Beschadigungen durch Fehlbetrieb am Gerat —Y
sicherstellen, daB die Netzspannung 230 Volt betragt. KT Z t Ist das Gerat fur einen Aufstellplatz mit glattem FuBboden bestimmt, RYN \ misssen die Standbeine mit Gummiplattchen unterlegt werden, damit das MS \ GerAt fest steht und nicht auf dem Boden hin- und herrutscht. \ Lee \ £ Zu Reparaturzwecken am Netzteil und den CPU-Komponenten muB die Rickseite des Gerates mindestens 50cm von anderen Geraten und der Wand entfernt sein.
bP BPE & Zum leichteren Transport ist das Gerat mit Rollen ausgeriistet. Daher besondere Vorsicht auf abschissigem Boden
Der Schwerpunkt des Aufsatzes liegt sehr weit vorn. Daher werden fiir den Ab- und Aufbau des Aufsatzes mindestens 2 Personen bendtigt.
Der Aufsatz wird in groBer Héhe montiert. Daher muB aus Sicherheitsgriinden eine Steighilfe, wie z. B. eine Leiter, ein Tritt oder ahnliches, verwendet werden.
Die Gesamthohe de Gerates betragt 2.05m. Daher Vorsicht bei tiefer hangenden Beleuchtungsk6rpern.
Fir den Transport oder bei einem Platzwechsel Gert in drei Teile zerlegen: Kopfteil, Vorderteil, und Fahreinheit
~\
PBPBBBPBE BB & AUS- UND EINBAU VON KOMPONENTEN UND TEILEN
Aufstellung, Service, Einstellung und Wartung dirfen nur von dafiir qualifiziertem Fachpersonal durchgefiihrt werden.
Es diirfen keierlei Veranderungen ohne vorherige Genehmigung am Gerat vorgenommen werden. Zuwiderhandlungen stellen eine Gefahrenquelle dar.
Fir die Repartur dirfen nur Originalersatzteile (incl. Schrauben) von NAMCO EUROPE LTD. verwendet werden
Vor Begin aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muB der Netzstecker gezogen werden
Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muB vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen ibernommen wird.
Teile des Netzteiles und Bilschirmes bleiben nach Abschalten noch hei8 und fihren Hochspannung. Dies kann zu Verbrennungen oder einem Elektroschlag fiihren. Diese Teile dirfen nich berihrt werden,
Vor der Montage oder dem Entfernen von Steckverbindungen und Steckern muB das Gerat ausgeschaltet werden
Bei Ziehen des Geratesteckers oder des Netzsteckers aus der Wandsteckdose stets den Stecker greifen und nicht das Kabel. S/
©) Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d’enregistement phonographique. Ces informations ne seront ni stockées gréce A un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l’autorisation de NAMCO EUROPE LIMITED.
Malgré le fait que les informations contenues dans ce manuel soient données de bonne foi et étaient actualisées au moment de leur impression, NAMCO EUROPE LIMITED se réserve le droit de procéder & des changements ou a des modifications sans avis préliminaire
Ce jeu a été fabriqué en respect des normes de la Communauté Européenne, aprés avoir été testé il reépond aux normes 89/ 336/EEC et 72/23/EEC, en application des standards EN55014, EN55104 et EN60335-1 (voir la couverture du manuel), et comme tel il comporte I'autocollant de conformité avec les normes de la Communauté Européenne. Tout changement non autorisé sur ce produit pourrait contrevenir a ces normes.
Sous certaines conditions extrémes d'interférence exteme, par example des transmissions radio, des décharges électrostatiques ou bien de interférences passageéres sur le réseau, certaines dégradations ou anomalies peuvent se produire. Le jeu retrouvera cependant son état normal de fonctionnement lorsque la cause de ces anomalies aura cessé ou se trouvera déplacée.
Ce jeu n’est pas une machine, telle que définie par la norme sur les machines 89/392/EEC MESURES DE SECURITE
Afin d'utiliser ce jeu en toute sécurité, bien lire ce manuel d'utilisation avant de procéder a son installation, son réglage ou son exploitation. Si le propriétaire de ce jeu en confie la démontage, installation, le réglage ou la maintenance habituelle & une autre personne, il devra s'assurer que cette personne ait lu les conseils d'utilisation et les passages du manuel se rapportant a ce théme, avant qu’elle ne commence son travail. Afin d’éviter tout accident pendant la durée d’exploitation de ce jeu, se conformer strictment aux conseils de sécurité décrits a la suite. Ce manuel ainsi que le manuel d'installation du jeu (la ol nécessaire) font partie des éléments nécessaires a installation de la machine et doivent étre mis a la disposition de l'utilisateur et du personnel de maintenance a tout moment. Ce jeu est uniquement destiné a un usage intérieur et devra étre utilisé comme tel. Namco Ltd. ne sera aucunement tenu responsable en cas d’accidents, de blessure ou de dommage quelconque résultant de modifications non autorisées ou d'usage impropre du jeu.
REMARQUES SUR LA SECURITE
Les termes de sécurité détaillés a la suite seront utilisés tout au long de la lecture de ce manuel. Il convient de vous familiariser aves chacun de ces termes ainsi que leur signification avant de procéder a installation, & la maintenace ou au réglage du jeu avertisseMent Z\ Ge terme annonce un danger qui pourrait éventuellement avoir des conséquences dommageables ou mortelles. Ne pas passer oiltre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées. ATTENTION ©) Ce terme indique qu'un danger menace la machine. Ne pas passer oltre ce signal jusqu’a ce que les conditions indiquéeé soient entiérement comprises et effectuées. (> 90> ase)
CONSIGNES GENERALES DE SECURITE
Allumer l'appareil seulement apras avoir vérifié qu'il a été correctement installé, et que les instructions du manuel ont été respectées.
Les notes de mise en garde doivent constamment demeurer en bon état et étre remplacées en cas de disparition, afin que le client puisse les lire clairement.
S'il y una erreur ou un probléme avec la machine, l'utilisation doit étre immédiatement interrompue et le probléme résolu avant toute nouvelle utilisation.
Liinstallation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.
Afin d’éviter un éventuel incendie, s’assurer que les fusibles soient remplacés par le méme type de fusibles et au bon voltage. L'utilisation d'autres sortes de fusibles ou autres matériels est interdite.
L’alimentation a l’intérieur du moniteur reste chaude et comporte des zones de haute tension méme si la machine est éteinte. Il existe donc un risque de brulure ou d’électrocution. Attention a ne pas toucher ces endroits.
Pour prévenir une éventuelle électrocution due a un défaut matériel, ce jeu DOIT étre muni d’une prise de TERRE connectée en toute sécurité
Si A tout moment les fils électriques sont endommagés, il faut les remplacer immédiatment
Ne pas mettre le jeu en mode de fonctionnement avant qu'il n’ait été correctement installé.
Avant de connecter la machine au réseau, s’assurer que la machine est installée sous la bonne tension et que les fusibles correspondent. OPP P BBB B BB
NOTES D’ INSTALLATION
A\ NE JAMAIS mettre le jeu en marche avant que Vinstallation ne soit complétement effectuée. = =: A\ _ Afin de prévenir une éventuelle électrocution, s’assurer que la machine est connectée au réseau avec une prise a de terre reliée selon les normes de sécurité. A\ _ Afin que les clients ne soient pas blessés par les
| mouvements du jeu, s’assurer qu'il existe au moins 500 | A | 5 |
mm de séparation aves les autres jeux ou les murs. & © Afin eviter que ta machine ne soit abimée suite a une WY, mauvaise operation, s'assurer que la tension sur le réseau 7
| principal soit de 230 volts AC. | cent | | | | |
S S
Note: Si l'endroit ot doit étre installée la machine a un sol pdli, il N WAN N
est recommandé de poser des tampons feutrés sous les SS \
| vérins pour éviter que le jeu ne glisse sur le sol | \N | \ | 5 |
QW _
Le jeu est foumi avec des roulettes pour une meilleure mobilité. Prendre garde quand la machine est déplacée sur une surface inclinée.
Le centre de gravité de la partie supérieure du jeu est situé sur l’avant, il est donc indispensable que deux personnes au moins soient employées pour installer ou déplacer la partie supérieure.
Liinstallation de la partie supérieure du jeu s'effectue en hauteur, il est donc important d’utiliser un élevateur quelconque pour en effectuer le montage.
La hauteur totale de l'assemblage principal est de 2050 mm, prendre garde aux encombrements de la partie supérieure (ex : illuminations du bandeau). > PEP BE Be
Quand le jeu est déplacé ou transporté, s’assurer qu’il est séparé en 3 parties: l'assemblage du haut (le bandeau), l'assemblage de devant (la cabine), l’'assemblage mobile.
S
DEPLACER ET REMPLACER LES UNITES ET LES PIECES DETACHEES.
Liinstallation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.
Ne pas apporter de modifications sur cette machine sans autorisation préalable, faute de quoi cela pourrait entrainer un danger.
Seules les piéces détachées Namco Europe Ltd. doivent étre utilsées pour le remplacement ou la réparation de piéces (y compris les vis)
S'assurer que l'interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d’une panne, réparations, etc.)
Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure
Les piéces de I’alimentation et du moniteur restent chaudes, a tension élévée méme lorsque la machine est hors tension, elle pourrait occasionner des brdlures ou des électrocutions. Attention de ne pas toucher ces endroits accidentellement.
S’assurer que la machine soit hors tension avant de brancher ou débrancher toute prise ou connecteur. > BP BP PBB BE
Lorsque l'on manipule la prise au réseau de la machine, ou lorsque les prises principales doivent étre débranchées, saisir toujours la prise, et non le cable. ~\
AN
THIS MACHINE IS DESIGNED FOR INDOOR USE ONLY. DO NOT INSTALL THE MACHINE IN THE FOLLOWING PLACES.
DIESES GERAT IST NUR FUR DIE GEWERBLICHE AUFSTELLUNG IN GESCHLOSSENEN RAUMEN BESTIMMT. DAS GERAT DARF AN FOLGENDEN PLATZEN NICHT AUFGETSTELLT WERDEN.
CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR. NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS.
- SPECIFICATIONS
POWER SUPPLY :-
AMBIENT OPERATING TEMPERATURE:-
MONITOR :-
COIN ACCEPTOR:-
DIMENSIONS :-
Assembled
Monitor Assy Step Assy Header
WEIGHT :-
Assembled
Monitor Assy Step Assy Header
ACCESSORIES :- 230volts AC
+5°C to +25°C
Hantarex 28" Polo with Auto Degauss
Mars CashFlow - 1 Channel
970(w) x 1800(d) x 2220(h)
970(w) x 910(d) x 1800(h) 970(w) x 890(d) x 1200(h) 660(w) x 375(d) x 420(h)
243kg
135kg 105kg 3kg
Keys: (Cash Door) .. (Coin Door) ... (Service Door
IEC Mains Lead.... Operators Manual. Monitor Manual. Cashflow Data Potentiometer Link Cable .
UOIN Bracket .....ceocccecsernssrersacsareasscomvenaneces 2
M10x25 Hex Head Screw M10 Spring Washer M10 Flat Washer
M5 Security Wrench ....
- HOW TO PLAY
This game is based on Alpine ski racing. The player stands on the steps and moves them left or right to control the skier. By using the inner edge when moving the steps, the skier slows down and turns quickly.
SINGLE PLAY . Race Mode The player races the computer skiers and the object is to cross the goal line first. The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased each time a player passes a check point. If a player wins in a fast time they can enter their initials. Select letters using the select buttons and enter them by using the decision (Viewpoint) button.
. Time-Trial Mode The object of the game is to pass between the flags (gates) and to cross the finish line in the fastest time. The rules require the player to go through the gates, so more technique is needed for this mode than the normal race mode. The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased by one second each time a player passes through a gate. If a player completes a course in a fast time they can enter their initials. Select letters using the select buttons and enter them by using the decision (Viewpoint) button. A player is not disqualified for not passing through a gate, however the player will not be able to enter their initials even if they cross the finish line in a good time.
LINKED PLAY When two games are linked, players on each game will be able to race against each other on the same course. When sufficient credit has been established and the start button has been pressed on one game, there is a time period before the start of the game during which another player can establish credit and press the start button on the other game to enable linked play
. Linked Race Mode The object of the game is to cross the goal line before the opponent. The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased each time the leading player passes a check point. If a player wins in a fast time they can enter their initials. Select letters using the select buttons and enter them by using the decision (Viewpoint) button.
. Linked Time-Trial Mode The object of the game is to pass between the flags (gates) and to cross the finish line faster than the opponent. No penalty time is given for touching the opposing skier. The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased by one second each time a player passes through a gate. If a player completes the course in a fast time, they can enter their initials. Select letters using the select buttons and enter them by using the decision (Viewpoint) button. A player is not disqualified for not passing through a gate, however the player will not be able to enter their initials even if they cross the finish line in a good time.
GAME SELECTION 7 Skier Selection After inserting sufficient credit, the "Skier Selection Mode" will be displayed. The player selects one of three skiers, "Basic", "Mogul" or "Downhill" by using the L/R select buttons and pressing the decision (Viewpoint) button
. Game Mode Selection After the Skier Mode has been selected, the "Game Mode Selection" screen is displayed. The player selects either the "Race Mode" or "Time-Trial Mode" by using the L/R selection buttons, and pressing the decision (Viewpoint) button. Linked Time-Trial Mode is only available if both players select Time-Trial Mode
. Course Selection After the game mode has been selected, the "Course Selection" screen is displayed. The player can select either the "Hi-Speed Course" or the "Technical Course" by using the L/R selection buttons, and pressing the decision (Viewpoint) button. When in linked mode, the Technical Course is only available if both players select the Technical Course.
. Viewpoint Selection The viewpoint button can be pressed at any time during a game to switch between the views.
Third Persons View: This is the view as seen by a third person. This view can be used to get an understanding of the surrounding conditions. The game normally starts in this view.
Players View: This is the view as seen by the skier. This provides an exciting view while skiing.
Behind View: This is the view from just behind the skier. This view can be used to get an understanding of the skiers posture.
GAME RULES
. Single Race Mode The player races against four computer skiers. The game will finish when the player crosses the finishing line within the given time period. The time period is increased each time a checkpoint is reached. If the time period reaches zero before the player has completed the course, the player will stop, the result will be displayed and the game is over.
. Linked Race Mode The players on two machines will race against each other. The game will finish when the player crosses the finishing line within the given time period. Both players can finish the course if they have sufficient time. The time period is increased each time a checkpoint is reached by the leading player and the extra time is added to both players. If the time period reaches zero before the player has completed the course, the player will stop, the result will be displayed and the game is over.
Single Time-Trial Mode The object of the game is to pass between the flags (gates) in the fastest time. The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased by one second each time a player passes through a gate.
Linked Time Trial Mode The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased by one second each time a player passes through a gate. If the distance between each skier becomes too close, the opponent will disappear from the screen and return when there is a greater distance between the skiers. The time period is not linked and the one second bonus for passing through a gate is only given to the player passing through the gate, so it is possible for the game to be over sooner for one player than the other. At game over a three second penalty will be added to a player's finishing time for each gate that the player has missed. If both players complete the course in the given time, the player with the fastest time, including penalties, is the winner.
- MAJOR COMPONENTS
Header Assy
Monitor
Coin Door/Cash Door
Ski Step Assy Si :
CPU SMPSU Amplifier Fuses
- MOVING THE MACHINE
J\ WARNING
AN
AN This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.
The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is high, and it is
The overall height of the machine, with Header assembly fitted, is 2200mm, take care of any overhead obstructions e.g. light fixtures.
- INSTALLATION
Notes on Installation
J\ WARNING
Z\
oO CAUTION NEVER turn the power to the machine ON until installation has been completed.
In order to prevent possible electric shocks, be sure that the machine is connected to the mains with asecurely connected earthed plug.
So that customers are not injured by the movement of the Ski Steps, ensure that there is at least 500mm separation between other machines or walls.
In order to avoid damage to the machine due to mis-operation, ensure that the voltage of the mains supply is 230volts AC.
In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm.
When installation is complete, it is imperative that the game is initialized. (See section 6-5 page 21)
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
AN
This machine is designed for Indoor Use Only
Do Not install the machine in the following places.
- Direct sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature.
- Outdoors
- Places where it would be in the way of emergency exits 4. Unstable places or places with excessive vibration. or fire extinguishing equipment.
5-1 Assembling the Machine
1. Remove 4off Security Screws (M5x16) and remove the Clamp Bracket Vac-Form from the front of the monitor cabinet.
Remove the 4off Hex Head Screws (M10x20), Spring Washers and Flat Washers.
CLAMP BRACKET VAC-FORM
SECURITY HEAD SCREW @ (w5e16)
Remove 2off Hex Head Screws (M10x20), Spring Washers and Flat Washers
SKI POLE CLAMP BRACKET
HEX HEAD SCREWS (wo X 20)
and remove the Shipping Bracket from the Step Base. Connect the 2 connectors between the Step Base and Monitor Base and push the two bases together, taking care not to trap any wires.
Fit the Joint Brackets using the 80ff Hex Head Screws (M10x25), Spring Washers and Flat Washers. (4off screws each side)
MONITOR BASE
HEX HEAD SCREW (M10x25)
- _ Refit the Clamp Bracket using the 80ff Hex Head Screws (M10x20), Spring Washers and Flat Washers so that the Ski Pole Joint Bar is clamped securely to the Monitor Cabinet.
HEX HEAD SCREW (nt0x20)
SKI POLE CLAMP BRACKET
- Refit the Clamp Bracket Vac-Form using the 4off Security Screws (M5x16)
CLAMP BRACKET VAC-FORM
SECURITY SCREWS
(MSxi6)
Level adjuster “=p
= @ wa
If this machine is installed on a smooth or shiny floor, it is recommended that rubber slip mats be placed under each adjustable foot to prevent the machine from moving when being played.
5-2 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is high and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc)
Connector Cover
- Remove the two security screws (M5x12) and remove the Connector Cover. Security Screw (M5x12)
Header Assy
Retaining Brackets
- Place the Header Assembly on to the monitor cabinet, slide the header back ensuring that it engages fully in to the retaining brackets at the front of the monitor cabinet.
Header Assy
- Fit the two security head screws (M5x12) to retain the Header Assembly to the cabinet. Security Screw (M5x12)
- Connect the connector and refit the connector cover using the two security screws (M5x12).
- ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power switch is located on the rear of the monitor cabinet.
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door.
- Service Switch. Press this switch to obtain game credits without incrementing the play meter.
- Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" (page 11))
COIN COUNTER °
°
LEFT PLAYER RIGHT PLAYER
TEST SERVICE TEST SERVICE
Service Bracket
6-3 Test Mode
- Open the coin door and slide the test switch "ON". The menu screen will be displayed on the monitor.
- Select the test required by pressing the ‘Left or Right Selection' push button. The selected test will 'blink'.
- Enter the selected test by pressing the 'Decision' push button. Select "EXIT" to return the "Menu Screen".
- After testing is completed, ensure that the test switch is returned to the "OFF" position to return to normal game mode.
The Test Switch must always be in the "OFF" position for normal game mode.
Ne MENU
COIN OPTIONS
GAME OPTIONS
VO TEST
MONITOR TEST
SOUND TEST
ADS TEST
OTHERS
©: ENTER </>: choose Sets the price of play (See 6-3-1)
Sets the game options (See 6-3-2)
Used for testing switches and controls (See 6-3-3)
Used for adjusting the monitor (See 6-3-5)
Used for testing sound and setting volumes (See 6-3-4)
Displays accumulated game data (See 6-3-6)
Used for testing the PC Boards and for initializing all of the settings (See 6-3-7)
Select L/R Buttons View Change
6-3-1 Coin Options
- Select item (1) "COIN OPTIONS" on the menu screen to set the game cost and related settings.
- Press 'Select L/R' to select the required item.
- Use the 'Decision' button to adjust the settings.
- Select "EXIT" to return to the menu screen. COIN OPTIONS [ DEFAULT IN GREEN ]
GAME COST 1 COIN 1 CREDIT ------
FREEPLAY OFF ~~
EXIT
<>: CHOOSE, CHANGE (_): ENTER Ne S
ITEM CONTENTS FACTORY SET
- Game Cost | No of Coins required for No. of credits - - - - - - settable 1-9 | 1 Coin 1 Credit
- Free Play | Yes/No NO
6-3-2 Game Options
- Select item (2) "GAME OPTIONS" on the menu screen to set the game options and related settings.
- Press 'Select L/R' to select the required item.
- Press the 'Decision' button to adjust the settings. Standard settings are displayed in green.
- Select "EXIT" and press 'Decision' to return to the menu screen.
GAME OPTIONS [ DEFAULT IN GREEN ]
ID No. 0 LEFT (a) GAME DIFFICULTY (b) SOUND IN ATTRACT (c) HI SCORE INITIALIZE Se (d)
EXIT
<>: CHOOSE/CHANGE (_) : ENTER N S
ITEM DESCRIPTION FACTORY SET
| (a) ID No | Sets machine as left or right when in linked mode | 0 Left |
| (b) Game Difficulty | A (easy) to C (hard) | B |
| (c) Sound in Attract | On / Off | On |
| (d) Hi Score Initialize | Yes/No (If Yes Hi Score will be reset when exiting test) | No. |
6-3-3 VO Test
Select item (3) "I/O Test" on the menu screen to test the switches, motor and step adjust.
Press 'Select L/R' to select the required item, then press the 'Decision' button to enter the test.
Select "EXIT" and press the 'Decision' button to return to the menu screen.
(— >» VO TEST
DIP 4 12345678 oevssesseseseeseeeeesepfeee (a)
LINK OFF SWITCH TEST MOTOR TEST LAMP TEST STEP ADJUST EXIT
</>: CHOOSE CO: ENTER X P
Shows condition of DIP SW 4 on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
Displays whether machine is linked. (See 6-4 )
For testing Switches and Control Pots. (See 6-3-3-1)
Not used on this machine.
For testing the pushbutton lamps. (See 6-3-3-2)
For initializing the Step Control Pots. (See 6-3-3-3)
6-3-3-1
1.
Select Switch Test from the 'I/O Test' menu. The following screen will appear on the monitor.
4 SWITCH TEST *)
| TEST Sw | ON | ..(a) | |
| COIN SW | ON | (b) | |
| SERVICE SW | ON | . | (c) |
LSELECTION BUTTON ON (d) VIEW CHANGE BUTTON ON......[....(e) R SELECTION BUTTON ON.......|.....(f)
| SWING | 0000 | 0000 | CENTER | (g) |
| EDGE | 0000 | 0000 | CENTER...l.....(h) |
\<+O+b : EXIT )
The word 'ON' will appear next to items (a) to (f) each time the respective switch is operated. When the skis are pushed left, ‘SWING-CENTRE' will change to 'LEFT' and 'OK' will appear just before it reaches the extreme left,. When the skis are pushed right, 'CENTRE' will change to 'RIGHT' and 'OK' will appear just before it reaches the extreme right. '0000' will increase when the skis are moved to the right and decrease when they are moved to the left. When the skis are tilted, 'EDGE-CENTRE' will change to 'LEFT or RIGHT' and 'OK' will appear just before they are fully tilted. '0000' will change as the skis are tilted.
Lett step Right step "EDGE" ‘OK' will only appear if you stand and apply weight to the edges of the ski steps. There is no problem if ‘OK' is not displayed when standing on the steps in the same way =? as normal play.
If 'OK' is not displayed when the edge is tilted left or right, re-initialize as described in section 6-5 "Initialization After Replacing Parts".
Operate both of the 'Select L/R' buttons and 'Decision' button together to exit and return to the 'I/O Test! menu screen.
6-3-3-2 Lamp Test
- Select Lamp Test from the ‘I/O Test' menu.
On entering 'L[AMP TEST' the View Change and Select switch lamps will illuminate in sequence and the relevent lamp name will be displayed on the monitor.
6-3-3-3 Step Adjust
- Select Step Adjust from the 'l/O Test' menu. The following screen will appear on the monitor.
(~ STEP ADJUST >
SWING 0000h ADO 0000h CENTER EDGE 0000h AD1 0000h CENTER
INITIALIZE COMPLETED
PUSH SERVICE SWITCH TO RESET
© : exit XN
- Ensure that the skis are in the centre and level, then press the service button. INITIALIZE COMPLETE ' will appear on the monitor display.
- Select EXIT to return to the Main Menu Screen.
Sound Test
Select item (4) "Sound Test" on the menu screen to test the sound and speakers.
The following screen will appear on the monitor.
~\ ( SOUND TEST
VOLUME LSP (0-63) 32
| RSP | (0-63) | 32 |
SOUND IN ATTRACT ON ATTRACT VOLUME
| LSP | (0-63) | 32 | d) |
| RSP | (0-63) | 32 | e) |
REQUEST SONG No. 0 f) MESSAGE:
EXIT \_ </>: CHOOSE ©: ENTER
Select the required item by ‘Select L/R' buttons. The selected item will ‘blink’.
Pressing the Decision button will cause the selected value setting to blink.
Pressing ‘Select R' will increase the value and ‘Select L' will decrease the value.
Press ‘Decision’ button to return to item select mode.
When selecting the 'Request Song No.' test, 'Select R' button will increase the song number and 'Select L' will decrease the number. The 'View Change' button will produce the sound of the song number selected. (Request Song 01 will produce a stereo sound test. Sound will be produced from the speakers in the following order:- Left speaker, Right speaker, Both speakers)
Press both Select L/R buttons and View Change button together to return to Sound Test Menu from Request Song No. Test
Item Description Factory Set
| a | Set left speaker volume | 00 Quietest - 63 Loudest | 32 |
| b | Set right speaker volume | 00 Quietest - 63 Loudest | 32 |
| c | Select sound for testing. Each number will produce a different sound. 01 will | . |
generate a stereo test.
6-3-5 Monitor Test
- Select item (5) “Monitor Test” on the menu screen to set up and adjust the monitor.
- Onentering monitor test, the screen will display one of the following test patterns.
GRADATION PATTERN CROSSHATCH CROSSHATCH WHITE WINDOW WHITE WINDOW WHITE WINDOW INTERLACE PATTERN VIEW ANGLE ADJUST (CRT) GREEN
VIEW ANGLE ADJUST (PROJECTOR) FULL WHITE
- Use 'Select L/R' buttons to change to the next pattern and 'Decision' button to return to the Main Menu.
- Refer to monitor manual for monitor adjustments.
6-3-6 ADS Data
- Select item (6) "ADS Data" on the menu screen to view machine history details.
- The following screen will appear on the monitor.
( ADS 1/2
| Hrs | Mins | Secs | |
| ON TIME | XX | XX | XX |
| PLAY TIME | XX | XX | XX |
| 1RS | XX | XX | XX |
| 1RL | XX | XX | XX |
| 1TS | XX | XX | XX |
| qTL | XX | XX | XX |
| 2RS | XX | XX | XX |
| 2RL | XX | XX | XX |
| 2TS | XX | XX | XX |
| 2TL | XX | XX | XX |
TOTAL PLAY 0000
AVERAGE XXMins XxXSecs
ADS CLEAR NO NEXT PAGE EXIT
©: ENTER L </>: cHoose
- This page displays total time that the machine has been switched on, total playing times of single and linked games for downhill and slalem courses, total number of games played and average game time.
- If ADS 'YES' is selected, all ADS Data will be reset.
- If 'Next Page' is selected, the following screen will be displayed.
( ADS 2/2 >
| BASICS1 | $2 | $3 | S4 | S5 | S6 | S7 | GOAL |
| 1RS | XX | XX | XX | XX | XX | XX | XX |
| 1RL | XX | XX | XX | XX | XX | XX | XX |
| 1TS | XX | XX | XX | XX | XX | XX | XX |
| 1TL | XX | XX | XX | XX | XX | XX | XX |
| 2RS | XX | XX | XX | XX | XX | XX | XX |
| 2RL | XX | XX | XX | XX | XX | XX | XX |
| 2TS | XX | XX | XX | XX | XX | XX | XX |
| 2TL | XX | XX | XX | XX | XX | XX | XX |
MOGUL
| 1RS | XX | XX | XX | XX | XX | XX | XX |
| 1RL | XX | XX | XX | XX | XX | XX | XX |
| 1TS | XX | XX | XX | XX | XX | XX | XX |
| 1TL | XX | XX | XX | XX | XX | XX | XX |
| 2RS | XX | XX | XX | XX | XX | XX | XX |
| 2RL | XX | XX | XX | XX | XX | XX | XX |
| 2TS | XX | XX | XX | XX | XX | XX | XX |
| 2TL | XX | XX | XX | XX | XX | XX | XX |
RACER
| 1RS | XX | XX | XX | XX | XX | XX | XX | ||
| 1RL | XX | XX | XX | XX | XX | XX | XX | ||
| 1TS | XX | XX | XX | XX | XX | XX | XX | ||
| 1TL | XX | XX | XX | XX | XX | XX | XX | ||
| 2RS | XX | XX | XX | XX | XX | XX | XX | ||
| 2RL | XX | XX | XX | XX | XX | XX | XX | ||
| 2TS | XX | XX | XX | XX | XX | XX | XX | ||
| LL | 2TL | XX | XX | XX | XX | XX | XX | XX | ) |
- This screen displays the the position on the course that the player reached at game over for single and linked game, downhill and slalem and each racer.
- Pressing the View Change button will return the screen to the ADS 1 page.
6-3-7 Others
- Select "Others" on the menu screen and press the View Change button.
This screen is used to test the PCB and to reset the game to factory settings.
6-4 Linking Two Machines
- Ensure that the power is "OFF"
- Loosen the two pozi head screws retaining the link cover bracket, located next to the mains-in socket on the rear of the monitor cabinet, and remove the link cover bracket.
Pozi Head Screw (M4 X 10)
- Set the slide switch on the link board to 'EXT' on both machines.
- Use the supplied link cables to connect each link board. (See Diag.)
Ext [a5] Int Ext [m5] Int
IN OUT IN OUT
- Turn the power to each machine "ON", and set the PCB ID using the test mode. (Refer to section 6-3-2 "Setting the Game Options" - page 13)
- Refit the link cover bracket and tighten the pozi head screws.
If the machines are used as single, non linked games ensure that the link cables are removed and the slide switch is returned to the "INT" position.
6-5 Initialization After Replacing Parts
Initialization must be performed after replacing the game PC board, Rom or Step Controls. If initialization is not performed, the game will not function correctly. During initialization, ensure that the step edges are level.
- Select Step Adjust from the 'I/O Test' menu. The following screen will appear on the monitor.
- Ensure that the skis are in the centre and level, then press the service button. ‘INITIALIZE COMPLETE ' will appear on the monitor display.
- Select EXIT to return to the Main Menu Screen.
STEP ADJUST >
SWING 0000h ADO 0000h CENTER EDGE 0000h AD1 0000h CENTER
INITIALIZE COMPLETED
PUSH SERVICE SWITCH TO RESET
© : exit Ne
- MAINTENANCE
ae >) In order to prevent injury or electric shock to service personnel, ensure that the MAIN POWER IS OFF before attempting any maintenance.
Before performing any work not described in this manual, be sure to contact your distributor to receive instructions or answers to questions. )
~\ ~ Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muB der Netzstecker gezogen werden.
Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muB vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen Ubernommen wird. ) \ > oi] Ee
S’assurer que l'interrupteur soit sor OFF avant de commencer tout travail de >) maintenance (localisation d'une panne, réparations, etc.)
Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure.
A yy,
Varmista, etta laite on kytketty POIS PAALTA ennen ty6n aloittamista.
Ota yhteytta maahantuojaan ohjeita varten, jos joudut tekemaan tydtehtavia, joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole. )
7-1 Replacing the Push Button Switch or Lamp Side Vac-form Side Vac-form
Remove the ten security head screws (M5x12) and remove both side vac-forms.
Remove the four security head screws (M5x12) and remove the play panel only sufficient to — disconnect the connector, taking care not to strain any wires.
- Remove the lamp/switch assembly by pulling it away from the switch body. Replace the lamp or switch.
Switch Body Lamp Swick
7-2 Replacing the Fluorescent Tube
- Remove the two security head screws (M5x12) and remove the acrylic retaining bracket.
- Remove the header acrylic
- Replace the fluorescent tube.
- Reassemble in reverse order. AN Warning The fluorescent tube may be hot take care when handling the tube.
Security Screw (M5x12)
Acrylic Retaining Bracket
Fluoresent Tube Header Acrylic
7-3 Replacing the Edge Potentiometer
- Remove the four security head screws (M5x12) and remove the step front vacform.
- Remove the two hex head screws (M6x16) and remove the cover plate.
Front Step Vac-Form
_ 4 seu sn (M5 X 12) Hex Head Screw - (M6 X 18) ‘ Front Cover Bracket
- Disconnect the potentiometer connector.
- Loosen the hex socket head set screw and remove the potentiometer complete with bracket.
Connector Hex Socket Set Screw
Potentiometer
- Replace the potentiometer taking care that the wires are re-soldered to the correct terminals.
Potentiometer oo
Potentiometer Bracket
7-4 Replacing the Swing Potentiometer
- Remove the four security head screws (M5x12). Loosen the two security head screws (M5x12) and remove the base front cover.
‘Security screw (M5 X 12) ‘Security Screw (M5x12)
- Disconnect the potentiometer connector.
- Loosen the hex socket head set screw (M4x8) and remove the potentiometer complete with bracket.
Hex Socket Head Potentiometer Set Screw (M4 X 8)
- Replace the potentiometer taking care that the wires are re-soldered to the correct terminals.
Potentiometer Bracket
Potentiometer
SLuVd “8
Item Description Part No
1 PCB Assembly- Alpine Racer 2 XAR-AR2PCB
| 2 | Astec SA301-3400 SMPSU 5V 30A | 83000008 |
3 Link PCB One Player Ro
| 4 | M16x95 Adjustable Foot | 88300079 |
Schaffner Mains-In Filter Assy 62500010
| ° | Schaffner Boot | 66000017 |
Interlock Switch 60000006
| ° | Interlock Switch Cover | 39000028 |
| 7 | 3 Channel Amplifier Ver3 | 46000036 |
| 8 | Side Vac-form Decal - LHS | 46000184 |
| 9 | Side Vac-Form Decal - RHS | 46000185 |
| 10 | Header Acrylic | 30000043 |
| 11 | Monitor Housing Side Vac-Form - LHS | 46000184 |
| 12 | Fluorescent Tube 18" 15watt | 64500009 |
| 13 | Starter 240v 4-80w Universal | 63000000 |
| 14 | Choke | 63300000 |
| 15 | Monitor Housing Side Vac-Form - RHS | 46000185 |
| 16 | Monitor Vac-Form | 46000186 |
| 17 | Hantarex 28" Polo Monitor | 84000026 |
| 18 | Coin Door Vac-Form | 46000191 |
| 19 | Swivel Castor - 75mm | 59000005 |
| 20 | Loudspeaker 6%c' Bass | 62000068 |
| 21 | Fan 230V 4%0' | 67000015 |
K-21
Item Description Part No
| 1 | Play Panel Decal Ver2 | 40000437 |
| 2 | Play Panel Vac-Form | 46000196 |
| 3 | Pushbutton Assy - MCPB Red | 60200247 |
| 4 | Pushbutton Assy - MCPB Yellow | 60200251 |
| 5 | Play Panel Loudspeaker Mesh | 46000195 |
| 6 | Play Panel / Speaker Mounting Wood | 37100113 |
| 7 | Loudspeaker 5%2' Mid High | 62000065 |
Item Description Part No
M4x20 Pz Pan Head - Black 26300391
| ' | M4 Flat Washer - Black | 28000132 |
| 2 | Ski Pole Grip Washer | 45000606 |
| 3 | Ski Pole Grip Bar | 46000239 |
| 4 | Ski Pole Joint Casting - LHS | 46000209 |
| 5 | Ski Pole Joint Casting - RHS | 46000210 |
| 6 | Ski Pole Grip - Black Slim Line | 46000245 |
Z H s lo ° 6 ® © [of te Wo aa. O O
@ 08 @ @
Item Description Part No
| 1 | Foot Protection Bracket - LHS | 46000237 |
| 2 | Step Rubber Fixing Plate | 46000222 |
| 3 | Step Rubber | 46000223 |
| 4 | Step Tray Shaft Spacer Washer | 46000220 |
| 5 | Bearing - 80FL-20 | 46000181 |
| 6 | Link Ball - BL 6D | 46000228 |
| 7 | Step Rear Swing Rod | 46000217 |
| 8 | Link Ball - BL 6DL | 46000229 |
| 9 | Foot Protection Bracket - RHS | 46000238 |
10 | Rosta Spring Retaining Bracket 46000218
| "4 | Rosta Spring DR-S-18x30 | 45000573 |
12 | M4x8 Hex Socket Set Screw 26300083 13 | Potentiometer Mounting Bracket 46000219 14 | Edge Potentiometer X008-023
Item Description Part No
1 | Swing Potentiometer X008-023 2 | Ski Pole Joint Bar 46000206 3 | Step Section Base Top Decal - Front 40000415 4 | Step Section Base Top Cover - Front 46000202 5 | Step Vac-Form - Front 46000226 6 | Ski Pole - RHS 46000205 7 | Ski Pole Decal 40000405 8 | Step Section Base Top Cover - Rear 46000201 9 | Step Rear Top Vac-Form 46000227 10 | Step Section Base Top Decal - Rear 40000416 11 | Ski Pole - LHS 46000204
- | Conduit Pipe - PAFS13 46000232
- | Step Rear Vac-Form 46000225
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
- SCHEMATIC
ert 1H steal ae ae cae
AE nor FLUORESCENT ASSY EaetH| @ [2 SEeEN ae NUTS TS Fy
aaa S34
‘
| 3 CHANNEL, | coe} et | { |
| AMPLIFIER | ee eeen | Hu |
mune Bret PS Tee tate 7 Ler sere TSS
| ME | TOO: | Hi Bees |
| atl | ara | mae PRES |
| roma | Secor | BIGHT SEE — |
Unpass 1513 HANTAREX:
| POLO | REEL | rep | f |
| 2a" | Vane = | fam | r |
sts wonrroe = F-test nic 1________nax | THE pn
FERRITE 1 oe oe ete eaath a
| SCS | Tat NEWT | F: | RED |
EME raw sos (3 tee
| ee eye | cu | iiss |
ate tsVae cunt te} ee
| BLUE | 44 Tre vae | anny fet acacie |
oS [riavde comet 61a
| aaael | ome | — | |
| oe | 4 3] 3 | dgdel | SWITCHMODE PSU |
& ge de | le Taco 4 e fe [eens
| j= | I | SPS TAC NEUT. |
| z | | | PCE FAN |
| la | i | E |
g a 3 sis a
| \z | | | maaey | B fe | RTT} —f} se |
| m: | = g& | fey [ete | a | |
| & | 1 | iwremugex | Hy | Stior ste] || tet |
if 1} | sie Se ie I cmpapst+— +!
| iz | & | | | SHRLOLE TE hear | ||
| zi] | 2 | a | | | LINK PCB |
1? Vg Fe cams th 7 ‘GREEN/YELLOW
SEE ELLY
230vAC MAINS IN EARTH STARPOINT za gS3 &
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.