CATHODE RAY TOMES

Road Riot 4WD Universal Kit TM-373 1st Printing

Road Riot 4WD (04 Dec 1991, conversion kit) (Atari Games, 1991) · Technical Manual · 64 pages · 71 sections · original scan

Page 1

| UNIVERSAL KIT : INSTALLATION e ; INSTRUCTIONS

LINK-CAPABLE

Contact your distributor for details

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Conversion kit for upright games

Page 4

Copyright © 1991 by Atari Games Corporation. Ail rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright 7=

laws. Courts ON

can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. WN ha

In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036 Printed in the U.S.A. 11/91 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner

ii Road Riot 4WD Universal Kit

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game.

  • Modify or alter any circuits in the game by using kits or parts ot supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely instalied with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Road Riot 4WD Universal Kit

SAFETY

SUMMARY

The following safety precautions apply to all game operators and service personnel, Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it, Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating, In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

iii

Page 6

Road Riot 4WD Universal Kit

2-6 . Color Test....... ~ ooN ~ « Convergence Test CONTENTS -Sound Test \ASICO5 Test DSP Comm Tests and DSP Link Test Complete RAM and ROM Test... Troubleshooting and Maintenance

introduction Installing the Foot Pedal . ideo Display Sync Problems Connecting the JAMMA Hart roubleshooting Installing the Road Riot 4WD Board Set . emoving and Réplacing the.Steering Control Installing the Bezel, Decals, Labels, and Attractio temoving and Replacing the Foot Pedal Assembly, Assembh} Ms~and-RAMs... 1 Installation How to Use*This*Manual Cabinet Equipment Requirements Tools Required..«: Inspecting. the-Ki Preparing the

See the List of Illustrations that

Glossary

Page 7

Road Riot 4WD Universal Kit

Figure 4-6 JSA (JAMMA Stand-alone Audioy TI PCB Assembly

Figure 4-7JAMMA Filter PCB Asserhblfee48

ILLUSTRATION

Figure 1-1Installed Kit Parts.zFigure 5-1Road Riot 4WD Game BCB Asmbly
Figure 1-2.Locations of Control Panel HolesSchematic Diagram...
to be Drilled...16Figure 5-2JSA Audio III Assembly Schenjatfc
Figure 1-3Hole-Cutting ‘Template for RoadDiagram.5-8
Riot 4WD Kit Control Panel ......-...... 1Figure 5-3.JAMMA Filter PCB Assembly ;
Figure 1-4 — Hole-Cutting Template for RoadSchematic Diagram1 514

Riot 4WD Kit Foot Pedal.

Figure 2-1 Self-Test Menu Screen. Figure 2-2. Adjust Volume Screen. Figure 2-3 Figure 2-4 — Coin Gptions-Screen Figure 25 Game-:Options’Screen . Figure-2- -Alphalnumerits) Test Screen . Figure 2-7 Motign Object Test t Se Figure 2-8 Playfield Test Scr = Fig 9 itch Test Screei 6 = 2-2 “Figure 2-10 Color Test Screen. ( Convergence Tes' Sohind Test Scree}

‘oad Riot 4WD Board se Road Riot 4WD Game P@

Page 8

Road Riot 4WD Universal Kit

vi

Page 9

CHAPTER 1

Installation

The Road Riot 4WD” conversion kit is a one- how to install the Road Riot 4WD kit in your

player game for a standard upright cabinet. In- cabinet. This chapter also describes game play. cluded in the kit is a steering control and a foot Chapter 2 contains self-test procedures pedal. ¢ For maximum earnings, two cabi- and additional diagnostic tests. The nets of the same style can be converted and self-test is important in the Road Riot linked together. To link two game cabi- 4WD game. You can troubleshoot nets together, you can order the PC boards, main circuits, and the Road Riot 4WD link kit controls using the screens in with the necessary cable and the self-test. You should

other hardware (the link kit is regularly test the boards and Atari part no, A049867-01). Contact your controls with the self-test to keep distributor for details. A separate supple- your game in peak condition and at top ment included in the link kit, CO-373-01, describes how to install that link kit. ¢% and maintenance procedures for the controls. + earnings. “ Chapter 3 contains troubleshooting

This manual provides information for installing, Chapter 4 contains the kit parts list and parts iltesting, and troubleshooting the Road Riot _lustrations. Chapter 5 contains the schematics 4WD™ conversion kit. # Chapter 1 describes for the Road Riot 4WD printed-circuit boards.

Page 10

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements

Table 1-1 lists the equipment required in the cabinet into which you are installing the Road Riot 4WD kit.

CAUTION Do not unplug or piug in the Road Riot 4WD game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Equipment Spe ication

Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-topeak positive polarity Video Display

Control Panel Metal only

8Q, 10W

+5 VDC or +12 VDC

Three-conductor with ground

+5 VDC + 0.25V @ 3.0 amps

+12 VDC @ 1.0 amp

-5 VDC @ 1.0 amp (optional)

Table 1-1 Equipment Requirements Speaker

Coin Counter

Power Cord

Power Supply

1-2 Road Riot 4WD Universal Kit

art N Desc

72-1606F #6-32 x 3/8"-Long Pan-Head, Cross- Recessed Screw 72-1612F #6-32 x 3/4"-Long Pan-Head, Cross- Recessed Screws (3) 72-6608S #6 x 1/2'-Long, Type AB, Pan-Head, Cross-Recessed Screws (2) 72-€624S #6 x 1%*-Long, Type AB, Pan-Head, Cress- Recessed Screws (2)

75-07002 #1/4 Fender Washers (8) 75-5112B #10-24 x 3/4’-Long Black Carriage Bolts (4) 75-5512B 1/4-20 x 3/4"-Long Black Carriage Bolts (4) 175004-706 —.154" x .375" x .125"-Thick Fiber Washers (2)

175014-1025 175014-1040 175014-1050 175015-0113 .156" x .312" Steel/Zinc Flat Washers (4) #10 Flat Washers (4) #1/4 Flat Washers (4) #6 Steel/Cadmium External-Tooth Lock Washers (4)

176038-4412 — #1/4-20 x .75" Tamper-Proof Flush Countersunk Cap Screws (4) 177010-244 #1/4-20 Hex Polymer Locknuts (8) 177026-0040 — #10-24 Zinc Nut/Washer Assemblies (4) 178020-812 #6, I.D. 140°, O.D. .25", L 812" Nylon RWD Spacers (2)

178032-002 #10 Wire & Cable Tie 178126-002 5/32" TamperProof Hex Driver Key 178328-001 Tamper-Proof T-20 TORX Key 178328-002 — Tamper-Proof T-10 TORX Key 038 158-01 Product I.D. Label 039450-01 FCC Compliance Label 047205-01 Attraction Shield 047209-01 Control Panel Cover 047853-01 Control Mounting Bracket 049319-02 Red Sieering Control Decal 049774-01 Black Monitor Bezel 949775-01 Attraction Panel Film 049776-01 Side Panel Decals (2) 049777-01 Control Panel Decal 049866-01 PCB Ground Plane and Mounting Plate 049970-01 Game Instructions Label for Control Panel

141026-001 -5'-I.D. Ferrite Split Beads (2) 160060-002 —_ 6.3V Square Green Start Button Assembly with Lamp A043825-02 — Foot Pedal Assembly A046501-01 = JAMMA Harness Assembly (optional) A047964-01 interconnect Control Harness Assembly

A049292-01_ JAMMA Filter Board Assembly A049454-03 _—_—Non-Shaker Steering Assembly A0498 13-01 Road Riot 4WD PC Board Set TM-373 Road Riot 4WD Universal Kit Installation Instructions (with control panel templates) A049867-01 Link Kit fot Road Riot 4WD kit (optional) Packaging materials are not listed. Al parts are a quantity of 1, except as noted in parentheses.

Table 1-2 Contents of Road Riot 4WD Kit

Page 11

Road Riot 4WD Universal Kit Installation

NOTE The parts in the optional link kit are not shown in this illustration. See the supplement to this manual (CO-373-01) for a fist of the parts supplied in that kit and how to install them. Jtems Not Shown: 04796401 038158-01 Contiol interconnect Product LD. Label Harness Assy 1099450-01 141026-001 FOC Compliance Lab Ferrite Bead 178126-002 (2places) 5/92" Tamper-Proof Hox Key Diver 178328-001 117092-002 7-20 Tamperproo! TORX Key 10-24 Wiro & Cable Tie 089774.01 047205-01 |04975-01 1178328-002 Twea79 Black Bezel Attraction Shiela ‘traction Film | T-10 Tamper-proof TORX Key Road Riot 4WD Universal Kit 047853-01 Control Mounting Bracket 173014-1050 41/4 Fiat Washer (4 places) 17010-2448 4114-20 Polymer Hex Locknut (4 places) 7555128 #1/4-20 x 3/4" Camiage Bolt Instalation Instuctions

049776-05 Side Panel Decal @ places)

|, ao49813-01 Foad Riot 4WD Board Set 049866-01 } PCB Ground Plane t S 4 and Mounting Plate Steering Control . as T2-8612F

Assy. (wio shaker)s:86-32 x4"

04921902 Pan-Hid Screw Rod Steering Contal Decal : 3 @ places) 75-07002 : s 175004706 {11/4 Fender Washer Fiber Washer (4 places} (2 places)

7010-244:£75014-1025

+#1/4-20 Polymer Hex Locknut - #6 Flat Washer (4 places) (4 pleces)

476098-4412‘|2A047292-01

#420 Countersunk Screw ‘ AMMA Fiter Board Assy.

#6 x 1 112" Sorew (places) 75015-0119 a > 46 Lack Washer Button Assy. . (4 places) 72-1606 6-92 x 91" Screw

| 175014-1040 Flat washer (4 pleces) 1A049825-02 17026-0040 Fost Pedal Assy. 810-24 NutWasher Assy, 17010-2448 (4 places) 174-20 Polymer arTrai Hex Locknut cit Parl Decl (came = | Hots 94 carage Sot Waterco Wash oxrae-01 pa, fepmces ortrol Panel Cover

Control panel in closed position

Figure 1-1 Installed Kit Parts

Page 12

Installation Road Riot 4WD Universal Kit

Cu) come

Sana 14 ese 18 coo onent Side RIN Connect to the SV RTN terminal on the power supply. However, if you have 12V RTN, connect one of the wires at pin 1,2, A, or B to the 12V RTN terminal. RTN Same as pin 1. +5V Connect to the +5V terminal on the power supply. +5V Connect to the +5V terminal on the power supply. However, if your power supply has a + Sense terminal, connect to the + Sense. -5V Connect to the -SV terminal of the power supply. If -5V is not available, connect to the 12V RTN or the 5V RTN or leave it unconnected. NOTE: /f you do not have (or use) -5V, the maximum power to the speaker will be reduced by half. +12V Connect to the +12V terminal of the power supply. If your coin counter(s) require 12V, also connect to the + side of the coin counter(s) Key COINCTR‘ — Connect this wire to one side of the left 12V coin counter. Note: Do not use 24V counters. Connect the ““* + side to +5V or +12V on the power supply, as appropriate, Not used SPKR + Connect to the + terminal on the speaker. Not used RED Attach to the video display. BLUE Attach to the video display. VIDEO GND. Attach to the video display. SELF-TEST Use this wire if you want en external self-test switch, However, the kit already has a self-test switch on the PCB, (if you connect an external self-test switch, switch off the switch on the PCB. Connect the wire to the N.O, terminal on the external self-test switch. Connect the common terminal of the switch to a GND wire.) Com! 16 = LTCOIN Connect to the N.O. terminal of the left coin switch. Connect the common terminal of the switch to a aa wire 17 __START1 Connect to the N.O. terminal of the start switch. Connect the common terminal to a GND wire. Rewnl is GAS UP Connectto the white wire of the foot pedal harness. Gar 19 = STEER Down Connect to the Y/R wire in position 6 of tne Control Interconnect Harness. Notused 2 EPI ROOT Notused RIGHi y 4 POSH 22 RT TRIGGER — Connect to the WBN wire in position 2 of the Control Interconnect Harness. i~PUsH 23 LTTRIGGER — Connect to the W/R wire in position 1 of the Control Interconnect Harness. “Ang 7 Not used 20mg 25 Not used SAmg 26 Notused a ceo GND Connect to the BK wires in positions 10 and 11 of the Control Interconnect Harness. hme 28 GND Connect to the negative sense terminal of the power supply (if it exists); otherwise connect to the common terminals of the switches.

Table 1-3 JAMMA Pin and Wire Connections

Page 13

Road Riot 4WD Universal Kit Installation

Instructions

C Solder Side NE <

i)ARTNConnect to the 5V RTN terminal on the power supply, However, if you have 12V RTN, connect one of

c +5V Same D +5V

Wnt -5V

SAMEFo+i2Vv

H Key Sore 2u COIN CTR 2

TA Not used

Ame B span é ~ Notused resem GREEN

AgsPCOMPSYNC,

Ss R__Service1 SAWE S Not used Cow 2 T RT COIN

—«UVNot used

ix v Not used

w Not used x Not used Y Not used

WZ—Notused

g a Not used

b ~ Notused

ecNot used

d Not used e GND

WVfGND

the wires at pin 1, 2, A, of B.to the 12V RTN terminal. Same as,pin A. Connect the +5V terminal on the power supply. Connect to the red wire ir\position 9 of the Control Interconnect Harness and te the red wire in the foot pedal harness. Connect to the -5V terminal of the power supply. If -SV is not available, connect to the 12V RTN or the 5V RTN (GND) or leave it unconnected.

NOTE: If you do not have (or use) -5V, the maximum power to the speaker will be reduced by half. Connect to the +12V terminal of the power supply.

Connect this wire to one side of the right 12V coin counter. Clip R19 on the game PCB if you use a second coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate.

Connect to the — terminal on the speaker.

Attach to the video display. Attach to the video display. Optional: attach te the N.O. terminal of the ist or main service switch.

Connect to the N.O. terminal of the right coin switch. Connect the common terminal of the switch to a GND wire.

Connect to the BK wire of the foot pedal harness. Connect to the common terminal of the switches.

NOTE The lamp in the square start button is not used in this kit version of Road Riot 4WD. Therefore, no wire connections to the lamp are shown in this table.

Table 1-3 JAMMA Pin and Wire Connections, Continued

Page 14

Installation

Tools Required

  • Drill with a 1/2-inch and 5/16-inch drill bits

© Phillips screwdriver

  • Flat-blade screwdriver
  • Socket wrench set and ratchet

© 5/32" hex wrench

  • Wire cutters and strippers
  • Straight edge
  • Squeegee ¢ =X-ACTO™ knife

+ Insulated wire connectors (if you are installing a new JAMMA harness)

¢ Carbon paper

© Saber saw

° File

¢ Bandsaw

  • Tape or glue

1.00" Dia. Road Riot 4WD Universal Kit

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Road Riot 4WD. kit serial number, part number, and description of the missing or damaged parts, and date received.

Preparing the Cabinet for

the Kit Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Figure 1-1 shows almost-all kit parts installed in a typical cabinet. Use this illustration as a guide while you install the parts.

  • Turn off power to the game, and unplug the power cord,
NOTE The four holes in the corners are not shown in this illustration. Drill these holes wherever space permits.

0.187" Dia. (2 places)

0.312" Dia (4 places) 4.75" Dia.

11.77"

Figure 1-2 Locations of Control Panel Holes to be Drilled

1-6

Page 15

Road Riot 4WD Universal Kit

  • Remove the following from the cabinet: e Existing PCBs
  • Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)compatible. Table 1-3 on the previous two pages assumes you have an available game cabinet with a JAMMA harness installed in it.
  • Control panel decals, labels, and controls
  • Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals.
  • Video display (monitor) shield, display bezel, attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Control Panel

Parts Needed from this Kit

To assemble the control panel, you need the control panel hole-cutting template, which is printed in Figure 1-3. Cut out the template sheet from this manual. You will also need the following parts from the kit:

  • Clear cover for the control panel ¢ Control panel decal
  • Green START button assembly
  • Red steering control decal
  • Control mounting bracket ¢ Game instructions label
  • Steering control © Four #424 x %"-long black carriage bolts, flat washers, and nut/washer assemblies for the steering control
  • Four #10-24 x %"-long black carriage bolts, flat washers, and nut/washer assemblies for the corners of the control panel cover

Installing the Parts

  • Using carbon paper, transfer the steering control mounting pattern from the template to the control panel. Save the template. Also refer to Figure 1-2 or 1-3 for the exact locations of all control-panel holes.
  • Drill four %" holes in the metal control panel for the steering control mounting bolts.
  • Drill two %" holes in the metal control panel for the start button’s mounting screws. Installation

BS Using a saber saw, carefully cut out the large hole for the steering control and the smaller hole for the start button. Deburr the sharp edges with a file.

  • Lay the plexiglass cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the button holes as close as possible to the locations shown on the template. Lastly, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners—wherever space permits.
  • Using a bandsaw, cut the control panel cover to its correct outside shape.
WARNING Wear saiety glasses when drilling the plastic control panel cover. Use care io avoid shattering or chipping the plastic.
  • Tape or glue the template to the plexiglass cover. To start the saber saw cut, drill a 1/2" hole inside the steering control hole and the start button hole.
  • Saw out the large steering control hole and the start button hole.

9, Drill the four 4" holes that will be used to mount the cover to the control panel and the holes to mount the steering control and start button.

  • To prevent injury, carefully deburr ail the edges of the plexiglass cover. -Install the control panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls. Mount the instruction decal on the control panel. Nv . Install the cover on the control panel with the four 3/4"-long carriage bolts, washers, and locknuts.
  • Install the steering control using the 3/4"-long cartiage bolts and #4-20 nut/washer assemblies.
  • install the start button assembly as shown in Figure 1-1, For maintenance and servicing information on the steering control, refer to Chapter 3 of this manual.
Page 16

Installation

Installing the Foot Pedal

Parts Needed from this Kit

To install the foot pedal, you need the foot pedal holecutting template (see Figure 1-4 at the end of this chapter). Cut out the template sheet from this manual. You will also need the following parts from the kit: © Foot pedal assembly

  • Four fender washers and locknuts

Installing the Parts

  • Tape the foot pedal template to the lower right corner on the front of the game cabinet (see Figure 1-1 for general placement). Refer to Figure 1-4 for the exact location of the foot-pedal holes. Using carbon paper, transfer the foot pedal mounting pattern from the template to the cabinet. Save the template.
  • Drill four %c" corner holes and a 1%” center hole in the cabinet front.
  • Feed the pedal harness through the large center hole. Insert the foot pedal’s threaded studs into the four small corner holes.

EN From the inside of the cabinet, install the four fendet washers and locknuts onto the threaded studs of the pedal. Plug in the pedal harness connector.

Connecting the JAMMA

Harness

i. If your game cabinet does not already have a JAM- MA harness, install a JAMMA harness in the cabinet (optional, Atari part no. A046501-01).

  • Install the square split beads on the harness as close to the PCB edge connector as possible. Hold the beads on the harness with the tie wrap included in the kit.

1-8 Road Riot 4WD Universal Kit

CAUTION You must install the JAMMA filter board and the split beads on the JAMMA harness to meet FCC requirements.
  • Using Table 1-3 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.

[ARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Road Riot 4WD kit requires +5V and +12V. If —5V is available, it should be used, too. Tie off any other voltage wires on the power supply besides +5V, -5V, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring.

Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3.

Connecting Coin Door Wires

  • Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.
  • Connect one terminal of the door lamps to one of the GND wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
Page 17

Road Riot 4WD Universal Kit

NOTE Do not use -5V for the coin door lamps. -8V is required for audio.

Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.

Connecting the Control Wires

Connect the steering control harness and the start button harness to the JAMMA harness using crimp splices or butt soldering, according to the information in Table 1-3.

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above.

Checking the JAMMA Connections

Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and —5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing the Road Riot

4WD Board Set

After you have checked the power on the JAMMA connector (above), install the Road Riot 4WD board set in the cabinet, by following these steps and referring to Figure 4-4: 1, Use the three #6-32 x %" long screws to connect the game PCB to the PCB ground plane and mounting plate.

  • Plug the JAMMA filter board onto the front of the game PCB, and mount it to the ground plane using one #6-32 x %" screw provided in the kit. Installation
  • Use two #6 x 4" screws and the two #6 x '%«" spacers to connect the game PCB into the back side of the drawer.
  • Then, use the two #6 x %" screws to mount the mounting plate into the front of the drawer. Plug the JAMMA harness into the filter board. Secure the JAMMA harness away from the PCB with cable ties. wn
  • Turn on the power to the game. Check that the game PCBs function. If a video picture is not present, see Chapter 3.

Installing the Bezel, Decals, Labels, and Attraction Assembly

The bezel, decals, labels, and attraction assembly are shown assembled in a cabinet in Figure 1-1.

Installing the Display Bezel

Find the black cardboard display bezel in the kit. ‘This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required.

Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC compliance label (part no. 039450-01) on the back of the.cabinet.

Installing the Side Panel Decals

Find the side panel decals in the kit. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-1, Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Page 18

Installation

Installing the Attraction Assembly

Find the Road Riot 4WD attraction shield and the attraction panel film in the kit. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1.

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings. If you have linked two game cabinets together, you must set both players to the same difficulty setting, or the game will not function properly after turning on the power. If the settings don’t agree, you can change them both to medium by pressing beth start buttons at power-up. You can also use the Game Options screen in the self-test to change the setting.

NOTE The factory-recommended coin option setting for “Discount to Continue” should be set to Yes (see Table 2-3 in this manual). Making your game match all the recommended settings results in a setting of 2 coins to start/1 to continue. We highly recommend this increase in price per play, to maximize your return on investment. However, this setting may not suit all jocations.

Maximizing Earnings

For maximum earnings, regularly maintain your Road Riot 4WD game following the instructions in Table 3-1, in Chapter 3. When you set up the game and when you collect money, perform the automated self-test and check the controls with the Switch Test in the self-test.

Game Play

This section describes the features and driving of the Road Riot 4WD* game. Road Riot 4WD Universal Kit

Introduction

Road Riot 4WD presents off-road racing competition combined with combative shooting action. Players drive highperformance off-road vehicles armed with a stun gun.

Road Riot 4WD is a oneplayer off-road racing game kit where players can compete for an overall season championship. Controls in this game include a start button, a gas pedal, and a steering control with trigger buttons. Players are challenged by the lifelike skidding and bouncing action of their fourwheel-drive vehicles on the track. The cars can also crash in several different ways, depending upon how an object is hit. The cars can roll on their sides, fly end over end, or even explode on impact. Twelve different tracks offer special terrain and competitor challenges, Each track has a different background, ranging from desert to mountains, corn fields to ice fields. Terrain and track obstacles vary for each setting. Video graphics are digitized pictures of real-life objects. The Road Riot 4WD racing vehicles, people, and obstacles on and around the track are realistically depicted. The life-like detail and humorous interaction with the video graphics enhances player appeal.

Two-Player Linked Game Play Two games can be converted and linked together via the optional link kit assembly (available from your distributor). The linked configuration encourages twoplayer competition; players can also choose to play individually. If two games are linked, there are several incentives for two-player simultaneous play. Two players can compete head-to-head against each other for the season championship of 11 different race courses. The road riot will continue as long as the player defeats the hosting opponent's yellow cars. If two players are playing a linked game, there is one less computer-controlled car to beat. Two players can cooperate to beat the opponent cars.

Page 19

Figure 1-3 Hole-Cutting Template for Road Riot 4WD" Kit Control Panel A.

ATARI

GAMES

© iS)

BUTTON

© ©

X-Y STEERING CONTROL

Page 20

Installation Road Riot 4WD Universal Kit

NOTES

1-12

Page 21

: Road Riot 4WD Universal Kit Installation

:

NOTE Place the foot pedal as low as possible against the bottom right corner of the cabinet.

GAMES

FOOT PEDAL HOLE PATTERN , : ‘ ‘ ‘ : :

‘

Figure 1-4 Hole-Cutting Template for Road Riot 4WD”" Kit Foot Pedal

1-13

Page 22

Installation Road Riot 4WD Universal Kit

NOTES

1-14

Page 23

CHAPTER

Self-Test

Use the Road Riot 4WD" self-test to check

the condition of the game circuitry .

and controls. You will see the self-

test information on the video dis-

play and hear the sound test in-

formation through the speakers. You do not need any addition-

al equipment to perform the

self-test. %% You should per-

form the self-test when you first set up the game, each time you collect

the money, or when you suspect

game failure. “ This chapter

shows the screens in the self-

test and explains each of the

tests. The screens and expla-

nations are arranged in the or-

der they appear in the self-test.

Table 2-1 lists all of the self-test

screens and their purposes.

Page 24

Self-Test

Entering and Exiting

the Self-Test

To enter the self-test, turn on the self-test switch on the bracket located inside the coin door (if you wired your kit that way). The JSA III Audio PCB also has a self-test switch on it. These two switches are wired in parallel, meaning that you can use either one independently. Exit the self-test by switching off any of the self-test switches.

Self-Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the list by pressing the left and right triggers; the corresponding test is highlighted in blue. Choose the screen by pressing the START button.

Adjust Volume

Adjust the volume of the game using this screen, shown in Figure 2-2. Control the volume by pressing the left and right triggers; the volume number increases or decreases. To restore the old volume level, push Road Riot 4WD Universal Kit

SELF-TEST

ADJUST VOLUME

GAME STATISTICS

COIN OPTIONS GAME OPTIONS

ALPHA TEST MOTION OBJECT TEST PLAYFIELD TEST

SWITCH TEST

COLOR TEST CONVERGENCE TEST usta ynceemam seatie

SOUND TEST ASIC65 TEST DSP COMM TESTS DSP LINK TESTS COMPLETE RAM/ROM TEST

Figure 2-1 Self-Test Menu Screen.

the gas pedal. Save the new volume and return to the self-test menu by pressing the START button.

Screen e or Purpose

Adjusts the volume. Game Statistics Screen Displays the game statistics. Coin Opticns Screen Use to set and check the coin options settings. Game Options Screen Use to set and check the game options settings. Alpha Test Screen Use to test for clarity of characters. Motion Object Test Screen Use to test the movement and color of game objects. Playfield Test Screen Use to check the playfield displays. Switch Test Screen Use to display the functioning of the game switches and controls. Color Test Screen Use to check the video display color circuits. Convergence Test Screen White Convergence Screen Violet Convergence Screen Green Convergence Screen A series of screens to check and adjust display convergence. Use to check and adjust video display convergence of red, blue, and green. Use to check and adjust video display convergence of red to blue. Use to check and adjust video display convergence of red and biue to green. Sound Test Screen Use to check the audio circuits.

ASIC65 Test Screen Use to test comm port, checksum, and internal RAM

DSP Comm Tests Screen Use to check the communications hardware (works only if you have installed the optional link kit). DSP Link Test Use to test the transmitting and receiving of data between two linked games (works only if you have installed the optional link kit). Complete RAM/ROM Test Screen Use to check the all RAMs and program ROMs.

Table 2-1 Summary of All Self-Test Screens

Page 25

Road Riot 4WD Universal Kit

VOLUME: 15

PUPLEPPEE PEPE eed

USE TRIGGERS TO CHANGE VOLUME PUSH PEDAL TO RESTORE OLD VOLUME PUSH START TO SET NEW VOLUME AND EXIT

Figure 2-2 Adjust Volume Screen.

Game Statistics

Use the information shown on the statistics screen, in Figure 2-3, and on the histogram screens to keep track of your game use and maximize your profits. Record the information on the Road Riot 4WD statistics page in the back of this manual. The statistics are collected from the last time the statistics were cleared. You can clear the statistics by pressing both triggers at the same time. Press the START button to leave this screen and go to the histograms.

  • Left Coins show the number of coins counted in the left coin mechanism.

° Right Coins show the number of coins counted in the right coin mechanism.

  • Aux Coins shows the number of coins counted on the auxiliary coin input.
  • New Games is the number of new games played.

Statistics Left Coins 2 1533 Right Coins 1838 Aux Coins 0 New Game 9433 Continuation Free Games Idle Time Active Time Solo Time Linked Time ror Count Total Credits ‘Total Coins

PRESS BOTH TRIGS TO CLEAR STATISTICS

PRESS START FOR HISTOGRAMS

Figure 2-3 Game Statistics Screen Self-Test

© Continuation is the number of continued games played.

  • Free Games is the number of free games played if Coin Options is set to free games. ° Idle Time shows the number of minutes the game was not being played.
  • Active Timeis the number of minutes the game was being played in any mode. ¢ Solo Time is the number of minutes a race was being held in single-player mode. ° Linked Time is the number of minutes a race was being held in two-player mode. -¢ Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 388,

Histograms

The histograms are two screens that contain information about the game. Press the START button to move to the next histogram. To clear all histograms, press both triggers while displaying the last histogram screen. Press START to exit from the last screen,

The first histogram shows new game times, and the second has continued game times.

Coin Options

Check and select the coin options on this screen, shown in Figure 2-4.

To move through the options, use the right trigger. Change the option in yellow type. The factory default

COIN OPTIONS (DEFAULTS IN GREEN)

FREE PLAY: NO DISCOUNT TO CONTINUE: YES GAME Cost: 2 COINS 1 CREDIT BONUS FOR QUANTITY BUY-IN: NONE RIGHT MECH VALUE: 1 COIN COUNTS AS 1 COIN, LEFT MECH VALUE: 1 COIN COUNTS AS 1 COIN

PRESS RIGHT TRIGGER TO SELECT OPTION PRESS LEFT TRIGGER TO SELECT SETTINGS PRESS PEDAL TO RESET FACTORY OPTIONS PRESS START TO SAVE SETTINGS AND EXiT

Figure 2-4 Coin Options Screen

Page 26

Self-Test

Option Settings

Difficulty Level* Medium Easy Easier Easiest Road Riot 4WD Universal Kit

Explanati

Establishes degree of game difficulty. Hardest Harder Hard Medium Hard

Car ColorRedvBlueLets you display each player's car in a different color

(used only in a linked, two-game setup)

Music in AttractYesvNoLets you choose whether or not to play music in the

attract mode.

Clear High Score TableYesNowLets you clear the high score table.
Auto High Score Reset)EnableyDisableAutomatically resets the high scores to the factory de-

faults after 2000 games, unless a player has entered his initials within the previous 200 games.

“If you have linked two games together, you must set both players to the same difficulty setting or the game will not function properly after turning on the pewer. If the settings don't agree, you can change them both to medium by pressing both START buttons at power-up. You cari also use the Game Options screen in the self-test to change the setting. Vv Manufacturer's recommended settings. These settings are shown in green on the screen.

Table 2-2 Game Option Settings

settings are shown in green. To change a setting, use the left trigger. To save the new settings, press the START button. This returns you to the select test screen. If you want to keep the original setting, although you have changed it, press the pedal. This brings back the original factory setting. Use the START button to exit. The coin option settings and factory defaults are explained in Table 2-3.

Game Options

Check and select the game options on this screen, shown in Figure 2-5. To move through the options, use the right trigger. Change the option in yellow type. The factory default settings are shown in green, To change a setting, press the left trigger. To save the new settings, press the START button. This returns you to the select test screen. If you want to keep the original setting, although you have changed it, press the pedal. This brings back the original setting. Use the START button to exit. The game option settings with factory defaults are shown in Table 2-2.

Alpha Test

The alpha test consists of a series of screens that you use to test the clarity of characters. Figure 2-6 shows the first of the alpha test screens. é ERAN GAME OPTIONS (DEFAULTS IN GREEN). EB DIFFICULTY LEVEL: ‘ MEDIUM. = CAR COLOR: 5 RED MUSIC IN ATTRACT: YES. AERO J

= CLEAR HIGH SCORE TABLE: NO AUTO HIGH SCORE RESET: ENABLE

PRESS RIGHT TRIGGER TO SELECT OPTION PRESS LEFT TRIGGER TO SELECT SETTINGS PRESS PEDAL TO RESET FACTORY OPTIONS PRESS START TO SAVE SETTINGS AND EXIT

Figure 2-5 Game Options Screen

The screens display all of the alphanumeric character sets. If the screens are not clear, you have a problem. To move through the screens, press either the left or right trigger. Use the START button to exit.

Motion Object Test

The motion object test screen, shown in Figure 2-7, tests the movement and color of various game objects. Select the test function with the START button. Use the pedal or steering control to move objects, change pictures, and change object size. Press the START button to move to the next test or exit.

Page 27

Road Riot 4WD Universal Kit Self-Test

Option Explanation

Free PlayNowYesSet this to “Yes” for demonstrating the game.
Discount to ContinueNoYeswLets you offer a reduced price per credit when players want

to continue a game.

Game Cost2coins 1 creditwSets the number of coins required for one credit.

8 coins 1 credit

Bonus for Quantity Buy-in Nonev 2coins give 1 (extra coin) 3coins give 1 3coins give 2 4 coins give 1 4coins give 2 Acoins give 3 5 coins give 1 5 coins give 2 5 coins give 3 6 coins give 1 6 coins give 2 6 coins give 3 7 coins give 1 7 coins give 2 7 coins give 3 8 coins give 1 8 coins give 2 8 coins give 3 Q coins give 1 Q coins give 2 9 coins give 3 Lets you choose various levels of bonus coins or no bonus.

Right Mech Value 1 coin counts as 1 coinw

1 coin count as 8 coins Is the number of coins each coin counts as in the right coin mechanism.

Left Mech Value 1 coin counts as 1 coinw

1 coin count as 8 coins Is the number of coins each coin counts as in the left coin mechanism.

V Manufacturer's recommended settings. These settings are shown in green on the screen.

Table 2-3 Coin Option Settings

Figure 2-6 Alpha Test Screen Figure 2-7 Motion Object Test Screen.

Page 28

Self-Test

Figure 2-8 Playfield Test Screen

Playfield Test

This test, shown in Figure 2-8, checks the condition of the scrolling playfield. Move the steering control left/right to see horizontal movement on the screen. Hold the tight trigger button while moving the control left/right to see vertical movement. Press the START button to exit the test.

Switch Test

The switch test allows you to display the status of the game switches and controls. The switch test screen appears in Figure 2-9. The items tested are:

  • Steering wheel left/right movement
  • Foot pedal potentiometer © Left trigger switch © Right trigger switch ° Start switch and start lamp As you activate each switch or control, make sure the correct words are highlighted in blue on the screen. If players complain of cars driving erratically, or whenever the control harness is unplugged, you must recalibrate the controls. Follow this procedure to do the calibration:
  • Press the right trigger and start button simultaneously. The numbers after WHEEL and PEDAL on the screen will change.
  • Turn the steering control to its right limit, and hold it there for 4 seconds. Then turn it to its left limit and hold it there for 4 seconds.

2-6 Road Riot 4WD Universal Kit

SWITCH TEST

WHEEL RIGHT/LEFT: PEDAL:

LIMITS: WHEEL '13, 7F, EC) ( PEDAL (AE, GA,27)

LTRIG RTRIG START

PRESS RTRIG AND START TO RESET PRESS LTRIG AND RTRIG TO EXIT esate

Figure 2-9 Switch Test Screen

we Press and hold the foot pedal for 4 seconds.

  • Simultaneously press both triggers to save the calibration and exit from the switch test. Do not simply turn the self-test switch off to exit from this test: doing so will not save the calibration.

Color Test

This test indicates ihe dynamic range of the video display color circuit in a series of seven screens. The first color test screen is shown in Figure 2-10. Advance to each screen by pressing the right trigger (the software cycles through all seven screens and then starts over again). The screens are as follows:

  • Red at the top, followed by green, blue, and white
  • Yellow at the top, followed by light blue, purple, and white

COLOR TEST

RTRIG=NEXT START=EXIT

Figure 2-10 Color Test Screen

Page 29

Road Riot 4WD Universal Kit

Solid red Solid green

Solid blue Solid white Naw Solid gray If the screens do not match this description, adjust the video display as described in the video display manual. Press the START button to exit.

Convergence Test

The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-11. To see the violet and green screens, press the right trigger. Press the START button to go to the test select screen. Check the following on the screens:

  • The grid lines should be straight within 3 mm, and the lines should not pincushion or barrel.
  • The convergence of the lines on the violet and white screens should be within 2 mm. If the screens do not meet these criteria, adjust the video display as described in the video display manual.

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-12. Use the steering wheel control to select the sound, and press the right trigger to listen to it. Pressing the left trigger stops the sound from playing. Press the START button to return to the select test menu.

Figure 2-11 Convergence Test Screen Self-Test

NUMBER OF SOUNDS. : 61

SOUND CPU STATUS: GOOD USE WHEEL TO SELECT SOUND RTRIG=PLAY LTRIG = STOP.

COIN MECH SWITCHES : LEFT RIGHT

0 0

Figure 2-12 Sound Test Screen

ASIC65 Test

Use the ASIC65 test screen to test the comm port, checksum, and internal RAM. The first screen is shown in Figure 2-13. You can select one of the three options shown. Use the left trigger to move to the next option. Use the right trigger to select an option. If you test the comm port, a message indicates whether or not it’s OK. The checksum option displays the checksum. The internal RAM test indicates whether or not the RAM is OK. Press the START button to exit.

ASIC65 TEST

TEST COMM PORT

GET CHECKSUM

INTERNAL RAM TEST

START = NEXT TEST

Figure 2-13 ASIC65 Test Screen

2-7

Page 30

Self-Test

DSP Comm Tests and DSP Link Tests

NOTE These tests only apply if you have installed the optional link kit, to link two upright game cabinets together. The Comm Link board is part of the link kit.

Each of these two main tests has several sub-tests that are selected from menus. These two main tests are described in more detail in the supplement included with the link kit, CO-373-01.

2-8 Road Riot 4WD Universal Kit

Complete RAM/ROM Test The RAM/ROM test checks both RAM and ROM. If the test passes, you will see a sequence of color screens, and then the self-test menu screen will reappear. If the screens turn to black and white or gray or if no message appears, the RAM is bad; you will need to replace it. If the ROM is bad, the checksum of the bad ROM is displayed. You need to replace that ROM. Press the START button to exit.

Page 31

CHAPTER 3

Troubleshooting

and Maintenance

This chapter con- circuit boards, and a

tains troubieshoot-

procedures for your <in,7ili, sei, ing tables and repair list of ROM-caused

problems, with spe- BAM 5. ROMs to check

Road Riot 4WD” game. The and replace. # The last part of the

chapter has two parts. The first part contains chapter has information about connecting the

three troubleshooting tables. The tables con- video display (if it requires separate positive

tain general troubleshooting information, the sync) and repair information for the steering

voltage levels and test points on the printed- and foot pedal controls.

Page 32

‘Troubleshooting and Maintenance Road Riot 4WD Universal Kit

Problem Suggested Action Coin Mechanism Problem

  • Check the wiring to the coin mechanism.
  • Check the voltage to the + side of the mechanism.
  • Test the coin mechanisms with the sound test screen in the self-test.

Game Play Problem BoOpa . Check the harness and connectors. . Perform the self-test. Check the voltage levels on the PCB. See Table 3-2, Voltage Inputs and Test Paints. Check What ROM Problems Look Like, Table 3-3, for specific ROM problems.

Steering/Foot Pedal Problems 1. Have the controls been lubricated with the correct type of lubricant? If not, \ubricate them shown in Figures 4-2 and 4-3.

  • Check the harnesses and connectors.
  • Check the switches on the control.
  • If you tock the control apart, have you reassembled it correctly?
  • Make sure all the parts on the control are in goed repair. Repair or replace parts.
  • Reset the limits on the steering control and the foot pedal

Sound Problem 1. Is the speaker volume turned up? (Volume is adjusted digitally in the self-test.)

  • Check the voltage on the JAMMA connector.
  • Check the wiring from the PCB to the speaker. 4, Check the voitage level to the PCB. See Table 3-2, Voltage Inputs and Test Points.
  • Replace the speaker.

Video Display Problem Screen is dark. 1. is the garne plugged in?

  • Is the game turned on?
  • Are the connections good?
  • Is the line fuse good?
  • Is the display brightness turned up?
  • Are the solder connections on the line filter and transformer good?
  • Is the JAMMA connecior on the PCB tightly con-
  • Check all of the items below. If you answer ro to any question, nected?

you have a problem with the video display, not with the game cir- Cuitry. See your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?

  • Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.)
  • If the jevel is not correct, check the connectors and the harness.

Only a colored screen appears. You probably have a serious RAM problem. Display area wavers or is too small

  • Doyou have correct power voltage to tne video display PCB?
  • Do you have correct high voltage to the video display? Picture is wavy.
  • Is the monitor ground connected to the monitor?
  • Are the sync inputs connected properly? Picture is upside down. When you serviced the display, you connected the wires incorrectly. Switch the horizontal or vertical yoke wires on the display. Convergence, purity or color problems. Use the screens in the self-test to adjust the video display. Use the adjustment procedures in your video display manual. Picture is not centered. Use the centering procedures in your video display manual.

Table 3-1 Troubleshooting Table

Page 33

Road Riot 4WD Universal Kit Troubleshooting and Maintenance

Voltage Test Point or LED Source and Purpose

+5 + 0.25 VDC+5V1Logic power from the switching power supply.

CR3 LED (Game PCB) Lights when 5 V is applied to the PCB and the reset (RST) jumper is open.

7CR9 LED (JSA Audio Ill PCB)Lights when the +12 V supply is good

CR3 LED (JSA Audio III PCB) Lights when the -5 V supply is good.

+12V+VOP (pin 4 of LM324)+12 V from the switching power supply. Positive supply for the analog

circuitry.

-8V-VOP (pin 11 of LM324)-5 V from the switching power supply (if connected). Negative supply for

the analog circuitry.

Table 3-2 Voltage Inputs and Test Points on the PCBs

Problem ROM Causing the Problem Check the ROM at:

Program works, but motion objects orGraphics ROMsPlayfield: 20C-22C, 20D-22D. Motion

playfield is wrong. Object High: 25-98. Motion Object Low: 2P-9P, Alphanumerics: 22)

Garbage on screen; program doesn’t work,Processor14B/C,

Program ROM 0 8C, 8D

Game program is erratic.Program ROM 19C, 9D
No sound or erratic sound.Audio Program120

Audio ADPCM 12E, 15E, 17E, 19

Table 3-3: What ROM Problems Look Like

Video Display Sync

Problems

This game board provides separate positive horizontal and vertical sync on a separate connector, for monitors that will not work with the composite negative sync signal provided at the JAMMA edge connector. This connector (labeled “Syne”) is located near the edge connector. Pin 1 is horizontal sync, Pin 2 is vertical sync, and Pin 3 is ground.

Troubleshooting

The tables in this chapter (3-1, 3-2, and 3-3) can help you troubleshoot problems in your game. The troubleshooting table lists possible sources of problems in various paris of the game. The voltage inputs and test points can help you troubleshoot PCB problems. The ROM problems table can help determine exactly which ROM might be causing game play problems.

Removing and Replacing the Steering Control

The steering control is shown in Figure 4-2. If you want to repair the X-Y steering control, disassemble it by removing it from the control mounting bracket (pod) on the contro! panel. The hardware that secures the pod and steering control is shown in Figure 1-1.

Signal Signal

1Red7GND
2GND8GND
3Key9Neg. composite sync
4Green10Positive V sync
“5GND11PositiveH sync

6 Blue

Table 3-4 Atari Games Video Connector

Pin Assignments

3-3

Page 34

‘Troubleshooting and Maintenance

Removing and Replacing the Foot Pedal Assembly

The foot pedal assembly is shown in Figure 4-3. If you want to repair the foot pedal, disassemble it by removing it from the front of the game cabinet. The hardware the secures the foot pedal is shown in Figure 1-1.

ROMs and RAMs

If you have think you have bad ROMs or RAMs, perform the ROM or RAM test in the self-test procedure. If you have a ROM problem, see Tabie 3-3. If you see Road Riot 4WD Universal Kit

only a colored screen and cannot enter the self-test, see Table 3-4. For the location of all the ROMs and RAMs on the game PCB, see Figure 4-5

Page 35

CHAPTER 4

~ Parts Illusteati

This chapter provides infor-

mation you need to

order replacement

parts for your kit.

Common hardware parts, such

as screws, nuts, washers, and so on, are

included in these parts illustrations. ¢ When

you order parts, give the part number, part

name, the number of this manual, and the serial number of your game. With this infor-

mation, we can fill your order

rapidly and correctly. We hope

this will create less

downtime and more

profit from your

games. Atari Games Customer

Service phone numbers are listed on the

inside front cover of this manual.

Page 36

Parts Illustrations

049773.01 Black Bezel (047853-01 ~ Contioi Mounting Bracket “175014-1050 #114 Flat Washer (4 places) 17010-244 ##114:20 Polymer Hex Locknut (4 places) 7555128 1114-20 x 3/4" Carriage Bol, (4 places)

A049454-03, Steering Control Assy. (vo shaker) (049319-02 Red Stooring Control Decal 75-0702 #14 Fender Washer (4 places) 17010-2484 1514-20 Polymer Hex Locknut (4 places) 176038-4412 4114-20 Countersunk Sorew

'047209-01 Control Panel Cover

Control panel in closed position 047205-01 Attraction Shield

175014-1029 Flat Washer (4places) 17028-0040 410-24 NuvWasher Asey, (places)

7551128 10-24 x 3/4" Carriage Bolt | (4 places) Road Riot 4WD Universal Kit

Items Not Shown: A07964-01 03815801 Control Interconnect Product ID. Label Harness Assy 1939450-01 141026-001 FCC Compliance Label Femte Bead 178126-002 (2 places) '5/92" Tamper-Proot Hex Key Driver 178328-001 178032-002 7-20 Tamper-proot TORX Key _—*#10-24 Wire & Cable Tie 178328-002 TM.373, ‘T-10 Tamper-proot TORX Key Road Rot 4WD Universal Kit Installation Instructions

099776-01 Side Panel Decal (2places)

Aodg6t3-01 oad Rist 4WD Board Set 049866-01 PCS Ground Plane and Mounting Plate 72-6612 6-02 x34" Pan-Hd Scrow (places) 1175004-708 Fiber washer @ places) 175014-1025 46 Flat Washer (places) ‘8087292-01 AMMA Fitter Board Acsy, 1178020-812 Spacor (2 places) 72-66248 961 1/2" Screw (2places) 175015-0113 #6 Lock Washer (4 places) 72-4606 86-92 x 818" Screw

‘A043825-02 Foot Pedal Assy. 17010-2464 1114-20 Polymer Hex Locknut (4 places) 75-0702 ‘V4 Fender Washer | (4 places)

Figure 4-1 Parts of Road Riot 4WD Universal Kit A049868-01 C

ney

Page 37

Road Riot 4WD Universal Kit Parts Illustrations

orseso.ot ors28.01 pedal teed Poca Sra { sor02r.o1 178012-006 Lithium Gre ovsezr.o | Ghat stain Ping iad ies

rreo12002 we petanrg ing (2 places) A084 3943-01 "| Foat Pedal Hames Assy

049832-01 ‘Stop Shaft

049826-01 Frame

178065-100

#832 Hex Nut 728808 8-82 x 1/2" Soc-Hd Screw

75-9188,

76-0808028 Bearing (4 places) Lubricate on the

043629-02 Unk Bracket 043601-01 Return Spring 75.0480 (2paces) 48 Spit Lock Washer 0¢9939-01 (2 places) Soring Sloeve 72-1806F ‘2 places) 98-32 x18" Pan-Hd Screw | places)

Figure 4-2 Foot Pedal Assembly A043825-02 D

a ws

Page 38

Parts Illustrations Road Riot 4WD Universal Kit

178247-003 478248-001 ‘Switch Bracket Trigger a —e

178249-104, Left Cover| I Switch Trigger 160026-001 Snap Switch

160050-001

'72-1408S 4-40.x 1/2 Pan-Hd. Screw (2 places)

178249-103 | Right Handle Cover

Figure 4-3 X-Y Steering Control Assembly A049454-03 B

Page 39

Road Riot 4WD Universal Kit Parts Ilfustratrations

72-8012

NOTE: The Shatt is part of the Frame Weldment (049452-01). 048861-01 X-Y Steering Mod Screw 106007-001 10-32 x 3/4" Socket- Hd. Cap Screw | 175007-001

171100-002 |_ Left Hand Kit Assy. | Loctite 290 Green Adhesive #10 Flat Washer (2 places}

4049462-01 Shaker Control Hamess Assy. 047485-01 | O-Ring Stop 178223-006 549\D. x 103W (2-133) O-Ring (2 places)

04975801 Base Flange Bearing 107027-001 Lithium Grease 72-CT604 6-32 x 1/4 Washer Hex-Hd. Screw (2 places)

76-081202 750 Bearing 407027-001 049452-01 Lithium Grease Lubricant Frame Weldment

178294-0606 50 Tubing |_| 04748201 Shaft Weldment 047488-01 Pivot Shatt Torsion Spring 178027-001 | 779 Nyogel Lubricant

047487-01 Spring Caich 047475-01 178181-7806 Centering Plate 4#8 Clearance Steel Spacer 72-CT604 (2 places) 6-82 x 1/4 Washer Hex-Hd. Screw —| 047479-01 (2 places) | Pot. Bushing 176041-3608 175002001 471100-001 6-32 x 1/2 Tamperproof Poesia CADE: Right Handle Kit Assy. Bunoa-Hial Sora Bracket Large Washer 1700-138 cone 175005-005 8-32 Hex Nut brine i ~_|-762x .010 Shim | 79.8808 ree 11908-1001 Flat Washer ; Loctite Adhesive! 5x Ohm Potentiometer 176012-001 A SRS He 750 Retaining Ring

Figure 4-3 X-Y Steering Control Assembly, Continued A049454-03 B

Page 40

Parts Illustrations Road Riot 4WD Universal Kit

NOTE ems marked with a @ are not part of this Board Set Assembly. Circled numbers refer to assembly steps described on page 1-9. Steps 5 and 6 are not shown in @ [7266248 « this illustration. 6x 1 1/2" Screw Le. (2 places) Antare7 08 Fer Washer Road Riot 4WD PCB Assy. oad Riot CB Assy. i@ place) 178020-812 « 178278-612 ‘ 86-32 x .75" Nylon Standoff a ae Spacer (2 paces) aces) 1700-536 |] 146-32 Nylon Hex Nut (2 places)!

4048974-08 JSA III PCB Assy (ROM version)

178171-1612 46-92 x75 Alum. 1/4" Round Standoff 72-16068 116-32 x 3/8" Pan-Hd, Screw (2 places) 175017-3013 #6 Split-Lock Washer (2 places) 175014-2021 72-6608S + |@ #6 Flat Washer #6 x 1/2" Screw . 72-1612F ¢ (2 places) (2 places) #6-32 x 3/4" Lg. Screw (8 places) 4049292-01 | @ 175015-0113 + JAMMA Filter Board Assy. —_ #6 External Tooth Washer 72-1606F + (3 places) #6-32 x 3/8" Screw 049866-01 175014-1025 ¢ 175015-0113 PCB Ground Plane #6 Flat Washer #6 External Tooth Washer & Mounting Plate (3 places) 175014-1025 + #6 Flat Washer

Figure 4-4 Road Riot 4WD Board Set Assembly A049813-01 B

4-6

Page 41

ong SSutsiae ae oF se os o ‘bf ees a, a 9g an a af

Ome. 2 eB cam ee 0 a ee: A = nara aC ae ww na eee eee ae: . a - 7 Ce a sor a a o oh _&| : — Fie ‘so ox ors —al ari

Se os Road Riot 4WD Universal Kit

wire that connects 2P, pin 22 to 11S, pin 3. However, yc 28 through 5S. tn that case, you should have me modific

NOTE: Your Road Riot 4WD Game PCB probably has one 4-meg.

A049757-02 A 1 os a] peed 4 oreo es 10 iy ocean ox 102 wz B

4-7 Figure 4-5 Road Riot 4WD Game PCB Assembly ation wire on the game PCB.

  • mom, ca a ? é now wn iw 8 oor t le yc omen feos oe EOF eT a omy ae : } 2

wd re ale Toes res 5 ices,

ees ore ho fe ose

Elvis L= four Game PCB may instead have four 1-meg. EPROMs at locations ROM at location 28. If so, it should have a modification es a f= "e2 ha r no Qian cmH Se eee ort fi ah a aL | f 0 Sa oct

co @ meg i 0s s oe oe 1 2 a ny, = 5), ee pe erage Lips Facet acol = a) fely

ar oa we de OP, = Ogre 8) sn COE ORE t

Fa J Parts Hlustratrations

Page 42

4-8 A047292-01 A Figure 4-7 JAMMA Filter PCB Assembly = i ca wa ha 2200PF| 2200PF 2200PF| /e200PF 270PF 270PF 270°F 270°F 22u0rF| 2200PF 2200PF| 2200Pr €20 91D aN » 38

& Figure 4-6 JSA (JAMMA Stand-Alone Audio) I PCB Assembly A048974-08 A germ ty BR Parts Hlustrations Road Riot 4WD Universal Kit

Page 43

CHAPTER 5

chematic Diagrams

This chapter con- The game PCB and

tains the schematic JSA TY PCB assem-

diagrams for the bly drawings are

Road Riot 4WD™ illustrated in Chap-

game PCB and the ter 4, Parts Illustra-

JSAM (audio) PCB. tions.

Page 44

Schematic Diagrams

com> OND rooney cesy> Cw centeva Ker eoNTRLD C-LOEKL CSPRRI+9 RUD > RED? fciray cyto owe csELrrest> <coIm.> eTRRTLD ‘cuPLAa OWA cuErmAD cRICHTLAD cupurTona> Ccpurt9N2 > CLeuTTONs) curFTLBD cRIGETLB) co) con

See Ee ORT ree 13 Yoder sere see sent 0 0D coum) seem-n 0 aon town? 0s cow? ewes o————a ost 30) Street O50 csv Srepe-3 C—a “30 can) waves o——— sev ca seer) O= cer Sremet ere _cecnren caren ce-LocKn saint O——-* space Copenss> ernest + runs cb oN) Senieeiz 0 ————+ mtb <oRtEN) Srna is Os ae cen) renin o——s vio cstvISED drweciso——weeneresy “trina wei o———+ caine ceoinn seer Os evant cSreeTm Serre-i6 O——+ ort <UPRE} Ser-i8 o————* ot opine) gaee-t0 oer iene deeecei o——— eT ceiomnen) Sewecte O————wecta: © cnurrows Yarns o———eectes —enauTrone> Sreeces o———ercie ——ERBUTTONS Jwe2s G———erctna “cuenta? dereeee O——e rere cA ine? o_o con? jree-es oo cub) oo — cnr COMECTED AT FINGERS ONLY cst wi rr x cies aa = x03 7a 3. pu3/orre me ey eee xe FE 19 o—enctie2 deer 14 O—s ACT TL at G 3 O—wrcted eet 12 O—enete ii o—enctms wr 10 oR? aeehr Soeur soo ms + o—ews 4 Soe srmars rye 3 0—scomne Bd $2 Seavices f 30 a0 zope] 2o—eev aoe ieee rae

ene

asme

‘SP. 04 Ce ee | ia ts ome 1 angie. cur 2 Oe vs Ne. OUr 3 O——= VIOEN

BND Road Rict 4WD Universal Kit

+3u2 TSYP TNS ove —t

aoe Tarr as F009 eyo cite 003 oY w noe 209 ow) on D TSTPLNE

x

per Deano = camer ote pemeery oes ise ot okie oan oft sia ots ait oe cxeie? O83 cxai32 oft om oi cents) O88 cenie> ot cami? eens ott cass of conta) fh ce o othe me oo Sar oe xara ot ioe ofa oe

Roo 10K

HON oo

COMECTED AT PINS 88 ANN 6D ONLY.

Page 45

Road Riot 4WD Universal Kit Schematic Diagsams

Ree mK

sor

ow

RS nea 100 = +— 93. 78y sorest aw 82 cwoxo me Bia wis waz suse} beret o1a5y

Rae chess a $00

aoe! om — oe

su SPARE GATES

‘

  • av0 caw’ a Tee

a2 abe Tae

wo ye Pry ee 40 PRO: az rey Fos Fo aa? ye [wae ED 5 Fes a

x ms Hy as Fe

az 8 20/238 ery rez ae “re pt Fe it

2 a2 20/18 PR wy Ta) are Foe 70

oruvasiiosie

Figure 5-1 Road Riot 4WD Game PCB Assembly Schematic Diagram 04975601 B

5-3

Page 46

Schema tic Diagrams Road Riot 4WD Universal Kit

470 F470 F470 F470 $70, “TO ic eo : we fo

wa7He Lae ws

Fa =

mtHe fe vow

hoes eee Leertezs 4cey tere Les: tses7 .

oi

470 70 470 F ro ie F

sia|,

a 7 ite 5 ee = ces 2 at A

Th 78 arse

ierifs sary sesaa
0078aef wage seeella
ss [eeaHa
aoe aarrwie 2D] anes |
ercu.ri
mnsireoe“
ee eepp Fisheze |, 00080810%
etewets!woesfa

i pt Fo gene 200 exc | 1 anao.eoe Bae seas te)ne EE] at

: ne

Swe BEE e S resem sts 3 fone tle Sass me se.RO3e—T A Yor on fmt Ey a were seat Sioa . DIR Ls2vs meet 68.4/R»

wn a

Page 47

Road Riot 4WD Universal Kit Schematic Diagrams

3t+—rs

: cana =

=:zw

i H

Etsae3
batt+7,ze ay
Le LaTST

tors Lego eye Aces toys begs tee Lepr

faTeSTTe
3peBiEsmoe:
ass+Peo aneHitya wr
ACTES ©Lawl i =ea ea
ot=oe4
ACTTRS,IFL3_,if0 in2138
START?; Live{3a__ay}

1a

Faia

inal __. rT

oe sp — we hee tnvoos 4 snoos oe

SSS : = em

Bone cea te conte :

oo

22 __scraEs cy :

on15-1994 11:51

Figure 5-1 Road Riot 4€WD Game PCB Assembly Schematic Diagram 049756-01 B

Page 48

Schematic Diagrams Road Riot 4WD Universal Kit

Page 49

Road Riot 4WD Universal Kit

Rano 10, 2a

RED 4 “a7 Fercatey our

02 ker

1K/2

2 tals coo —r}$0

©

a es ayo 2 ¥

irswhat|e{o0 32
minisGhe[aes

fs sal Can be ZA arn. 18 are a EI =H 0 ia a eT as CX orm] vcrers

mel® Tt oo

FSTRC =+—+f0%HSYNC.DUT

toe

+ tak an 30 * COFPSTAT ¥e0 ‘oe

a8

vere eL22S0usme. our

see be tes Tibor iad + idore en vio +80 dans 2a

nar 1." Schematic Diagrams

w

ae 2Na808

ay

nis etait 3 cay r itor

eyioeno

aeaseat iiss

Figure 5-1 Road Riot 4WD Game PCB Assembly Schematic Diagram 049756-01 B

Page 50

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 53

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 54

Schematic Diagrams Road Riot 4WD Universal Kit

oy

y02_| 26 Vor rw [44 nas

ps ap LS F481 ween

exo} sorxer

eS)

5-12

Page 55

Road Riot 4WD Universal Kit

Ray 3.1K

COT Tr

i R35, ata ane

“ aa ae z naa ro i crete ett sooetzy70 70 #8 sose tien softs soe Bitsy safe soze—an aft soee—ti30 —30[f sore—i20—20f3 seein to oS oe] users

Figure 5-2 JSA Audio Ill Assembly Schematic Diagram 048973-01 C Schematic Diagrams

ry Pur FoR ths03)

‘q eax

JT? we

os Les

woe

runout

Sts

5-13

Page 56

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 57

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 58

Schematic Diagrams Road Riot 4WD Universal Kit

NOTES

5-16

Page 59

APPENDIX

Glossary

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE ‘The true state of a signal. For example: The active state for is low.

ADDRESS: A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation,

ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE ‘The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero, ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER:

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g,, a bulfer amplifier)
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.

CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s), COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circutiry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing, DARLINGTON A two-transistor amplifier that provides extremely high gain DC Direct current, meaning curient flowing in one direction and of a fixed value.

DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects

gl-1

Page 60

the electron beam horizontally and the other set deflects the beam vertically, DIAGNOSTICS A programmed routine for checking circuitry, For example: the self-test is a diagnostic routine.

DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the mictoprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME ‘The period during which a game is malfunctioning or net operating correctly due to machine failure,

EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage. GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL ‘A number system using the equivalent of the decimal number 16 as a base. ‘The symbols 0-9 and A-F are usually used. IMPLODE

To burst inward; the inward collapse of a

vacuum tube,

vo Input/Output, IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game

LOGIC STATE ‘The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (In-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one highspeed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A readonly memory device (see ROM) is broken into discrete blocks of data, These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board.

PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang)
  • An instrument for measuring a voltage by balancing it against a known voitage. RAM Random-access memory. A device for the temporary storage of data, RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam, RETRACE Ina raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory, A device for the permanent storage of data.

SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g, the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node, This process continues until a fault is located.

TROUBLESHOOT ‘The process of locating and repairing a fault

VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program maifunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 61

A

ATARI

GAMES

Road Riot 4 Kit Statistics Sheet

Date Recorded: Location:

Meter:

Statistics Screen

Left Coins:

Right Coins:

Auxiliary Coins:

New Games:

Continuation:

Free Games:

Idle Time:

Active Time:

Solo Time:

Linked Time:

Error Count:

Total Credits:

Total Coins:

Average Time/Credit: LTTE TTT TTT Average Time/Coin:

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

eel el elle elle pele ell el pelle pel el elle fel fel el pelre

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thisty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that aid products are defective;
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

PEE eee eee eee eee lela elle elelel ele

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their jud; ment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is istributor.

Page 64

ad

COKPOKATION