CATHODE RAY TOMES

Road Riot 4WD Universal Kit TM-373 2nd Printing

Road Riot 4WD (04 Dec 1991, conversion kit) (Atari Games, 1991) · Technical Manual · 64 pages · 66 sections · original scan

Page 1

UNIVERSAL KIT

INSTALLATION

INSTRUCTIONS

LINK-CAPABLE

Contact your distributor for details TM-373 2nd printing

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

Universal Kit

Installation Instructions

Conversion kit for upright games -

Page 4

Copyright © 1991 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976.

This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036 Printed in the U.S.A. 01/92 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Iflustration and Design: Mary Ohanessian Sumner NOvTrer ReE.

NON-ATARI

PART

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-Atari parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram. « The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely ingtalled with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation, See the inside front cover of this manual fOr service in your area.
Page 5

Road Riot 4WO Universal KE

AFETY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not phig in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have on! two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you bave checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC fine voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display. be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (C) Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. Fi it tach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. ing non-Atari parts or modifying the game circuitry ay be dangerous. and could injure you and your players. SUMMARY

Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating, In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors On each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe), If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information,
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will yoid the anty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and or technicians can be killed of injured if instructions are not followed.
Page 6

Road Riot 4WD Universal Kit

Color Test Convergence Ti

1 Installation. _ LNStGHG. rete ees 2 <3 Troubleshooting and Maintenance :aUntroduction . Installing the Foot Pedal . Video Display Syne Problems Connecting the JAMMA Harné ‘Troubleshootin Instailing the Road Riot wD Board: Set Removing and ra teering Control Installin; ARemoving and Replacing the Foot Pedal 3 Assembly . OMs-and-RAM Troma, =f Setting the Coin and

ee the List of Illustrations that follows. Schematic ; : # See the List of Illustrations th: GOSsary

Page 7

Road Riot 4WD Universal Kit

Figure 4-6 RATIONS Figure 4-7

Figure 1-1 Installed Kit Parts... oe Figure 1-2 Locations of Control Panel Hole: + 1-3 Figure S-1

to be Drilled... 146 Figure 5-2 Figure 1-3. Hole-Cutting Template for Road Riot 4WD Kit Control Panel... 1-11 Figure 5-3 Figure 1-4 Hole-Cutting Template for Road Riot 4WD Kit Foot Pedal . 1-13

Figure 2-1. Self-Test Menu Screen. Figure 2-2. Adjust Volume Screer Figure 2-3 ech Figure 2-4 Figure ~o Figure 2 Figure Figure 2-8 Figure 24

) ;X-Y Steering Control / Road Riot 4D Board $ Road Riot JSA (JAMMA Stanc-along Auclic

JAMMA Fitter PC B Assembl TEE PCB Assembly

Road Riot AWD Game PCB Assembly Schematic Diagram... ve BD ISA Audio UT Assembly Schematic Diagram. ; 38 JAMMA Filter f i} Schematic Diagram 5-14

Summary of mg.Option Jeti ae Option Setting

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9

CHAPTER 1

Installation

The Road Riot 4WD™ conversion kit is a one-

player game for a standard upright cabinet. Included in the kit is a steering control and a foot pedal. @ For maximum earnings, two cabinets of the same style can be converted and linked together. To link two game cabi-

nets together, you can order the Road Riot 4WD link kit

with the necessary cable and

other hardware (the link kit is

Atari part no, AQ49867-01). Contact your

distributor for details. A separate supplement included in the link kit, CO-373-01,

describes how to install that link kit. +

This manual provides information for installing, testing, and troubleshooting the Road Riot 4WD™ conversion kit. 4 Chapter 1 describes How to Use THis MANUAL

how to install the Road Riot 4WD kit in your

cabinet. This chapter also describes game play.

  • Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Road Riot 4WD game. You can troubleshoot

the PC boards, main circuits, and

controls using the screens in the self-test. You should

regularly test the boards and controls with the self-test to keep your game in peak condition and at top earnings, % Chapter 3 contains troubleshooting and maintenance procedures for the controls. # Chapter 4 contains the kit parts list and parts illustrations, #& Chapter 5 contains the schematics for the Road Riot 4WD printed-circuit boards.

Page 10

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements

Table 1-1 lists the equipment required in the cabinet into which you are installing the Road Riot 4WD kit.

CAUTION Do not unplug or plug in the Road Riot 4WD game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Color RGB meni Separate positive horizontal Video Display

and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-topeak positive polarity Control Panel Metal only Speak BQ, 10W +8 VDC or +12 VDC Coin Counter

Power r Cord Power Supply Three conductor with ground "45 VDC + 0.25V @ 3.0 amps +12 VOC @ 1.0 amp 5 voc @ 10. 1 8 amp (optional) Table 1-1 Equipment Requirements Road Riot 4WD Universal Kit

Part No. Descr

72-4806F 46-32 x 3/8"-Long Pan-Head, Cross- Recessed Screw 721612F #6-32 x 3/4"-Long Pan-Head, Cross- Recessed Screws (3) 72-6608S #6 x 1/2"-Long, Type AB, Pan-Head, Cross-Recessed Screws (2) 72-66248 #6: 14"-Long, Type AB, Pan-Head, Cross- Recessed Screws (2)

75-07002 #1/4 Fender Washers (8) 75-5112B #10-24 x 3/4"-Long Biack Carriage Boits (4) 75-6512B 1/4-20 x 3/4"-Long Black Carriage Bolts (4) 175004-706 154° x 375" x .125"Thick Fiber Washers (2)

175014-1025 175014- 1040 175014-1050 175015-0113 166" x 312" Steel/Zine Flat Washers (4) #10 Flat Washers (4) #1/4 Flat Washers (4) #6 Steel/Cadmium External-Tooth Lock Washers (4)

#1/4-20 x 75° Tamper-Proof Flush Countersunk Cap Screws (4) 176038-4412

177010-244 #1/4-20 Hex Polymer Locknuts (8) 177026-0040 —-#10-24 Zinc Nut/Washer Assemblies (4) 178020-812 #6, 1.0. .140°, 0.0, .25", L812" Nylon RWD Spacers (2)

178032-002 #10 Wire & Cable Tie 178126-002 5/32" Tamper-Proof Hex Driver Key 178328-001 Tamper-Proof T-20 TORX Key 178328-002 Tamper-Proof T-10 TORX Key

038158-01 Product |.D. Label 039450-01 FCC Compliance Label 047205-04 Attraction Shieid 047209-01 Control Panel Cover

047853-01 Control Mounting Bracket 049319-02 * Red Steering Control Deca! 948774-01 Black Monitor Bezel 049775-01 Attraction Panel Film *

049776-01 Side Panei Decals (2) 049777-01. — Centro! Panel Decal 049866-0T PCB Greund Plane and Mounting Plate 049970-01 Game Instructions Label for Control Pane! 141026-001 .5"-LD. Ferrite Split Beads (2) 160060-002 6.3V Square Green Start Button Assembly with Lamp. A043825-02 Foot Pedal Assembly A046501-01 JAMMA Harness Assembly (optional) AGA7964-01 interconnect Control Harness Assembly

A049292-01 JAMMA Filter Board Assembly A049454-03 — Non-Shaker Steering Assembly A0498 13-01 Road Riot 4WD PC Board Set TM-373 Road Riot 4WD Universal Kit Installation instructions (with control panel templates) A049867-01 Link Kit for Road Riot 4WD kit (optional) Packaging matenals are not isted. Ail parts are a quantity of f, except as noted in parentheses Table 1-2 Contents of Road Riot 4WD Kit

Page 11

Road Riot 4WD Universal Kit

NOTE The paris in the optional link it ate not shown in this #ustration. See the supplement to this manval (CO-373-01) lor a list of the parts supplied in that kit and how to install them installation

Figure 1-1 Installed Kit Parts

Page 12

Installation Road Riot 4WB Universal Kit

BSBRRISLB +5V +5V

+120

Key COIN CTR 1

Not used SPKR + Not used RED BLUE VIDEO GND SELF-TEST

LT COIN

START1 GAS STEER Not used Net used RT TRIGGER LT TRIGGER Not used Not used Not used GND GND Connect to the 5V RIN terminal on the power supply. However. if you have 12V RTN, connect one of the wires at pin 1, 2, A, or B to the 12V RTN terminal. Same as pin 1. Connect to the +5V terminal on the power supply, Connect to the +5V terminal on the power supply. However, Your power supply has a + Sense terminai, connect te the + Sense. Connect to the -5V terminal of the power supply. If -5V is not available, connect to the 12V ATN or the 5V RTN or leave it unconnected. NOTE: if you do nat have (or use) -5V, the maximum power to the speaker will be reduced by hai. Connect to the +12V terminal of the power supply. If your cain counter(s) require 12V, alse connect to the + side of the coin counter(s).

Connect this wire to one side of the left 12V coin counter. Note: Bo net use 24V counters. Connect the + side to +5V or +12V on the power supply, as apprapriate,

Connect to the + terminal on the speaker,

Attach to the video display. Attach to the video display. Attach to the video display. Use this wire if you want an external self-test switch. However, the kit already has a self-test switch on the PCB. (if you connect an externat self-test switch, switch off the switch en the PCB, Connect the wire to the N.O. terminal on the external self-test switch. Connect the commen terminal of the switch to a GNB wire.} Connect to the N.O. terminal of the left coin switch, Connect the common terminal of the switch to a wire. Connect to the N.O. terminal of the start switch, Connect the common terminal to a GND wire, Cennect te the white wire of the foot pedal harness. Connect to the Y/R wire in position 6 of the Control Interconnect Harness.

Connect to the W/BN wire in position 2 of the Centro! Interconnect Harness. Cennect te the W/R wire in pesition 1 of the Contre! Interconnect Harness.

Connect te the BK wires in positions 10 and 11 ef the Central Interconnect Harness. Connect to the negative sense terminal of the power supply (if it exists); otherwise connect to the common terminals of the switches.

Table 1-3 JAMMA Pin and Wire Connections

Page 13

Road Riot 4WP Universal Kit Installation

Solde:

ARINConnect to the SV RTN terminal en the power supply. However, if you have 12V RTN, connect one of

the wires at pin 1, 2, A. or B to the 12V RTN terminal,

BRINSame as pin A.
Cc+5VConnect the +5V terminal on the power supply.
a+5VConnect to the red wire in position 9 of the Contro! Interconnect Harness and to the red wire in the foot

pedal harness.

E~8VConnect te the -SV terminal of the power supply. If SV is not available. connect to the 12V RTN or the

5¥ RTN (GNB) or leave it unconnected.

NOTE: If you do not have (or use) -SV, the maximum power to the speaker will be reduced by haif.
F+124Cennect te the +12V terminal of the power supply.

# Key

JCOIN CTR 2Cennect this wire to one side of the right 12V coin counter. Clip R19 on the game PCB if you use a sec-

end cein counter. Note: Do nat use 24V counters, Connect the + side to +5V or + 12V on the power supply, as appropriate. Not used SPKR- Connect to the - terminal on the speaker. Net used GREEN Attach to the video display. COMPSYNC Attach to the video display. Service 1 Optional: attach to the N.O. terminal of the 1st or main service switch, Net used RT COIN Connect to the N.O. terminai of the right coin switch. Connect the common terminal of the switch to a GND wire. . Not used Not used Not used Not used Not used Not used Net used Not used Not used Not used GND Connect to the BK wire of the foot pedal harness. GND Connect to the commen terminal of the switches. “OROTMNKCK ECC AMRWZROX

NOTE The lamp in the square start button is not used in this kit version of Road Riot 4WD. Therefore, no wire connections to the lamp are shown in this table.

Table 1-3 JAMMA Pin and Wire Connections, Continued

1-5

Page 14

Installation

Tools Required

© Drill with a 1/2-inch and 5/16-inch drill bits

*¢ Phillips screwdriver © Flat-blade screwdriver

© Socket wrench set and ratchet

© 3/32" hex wrench

¢ Wire cutters and strippers

  • Straight edge
  • Squeegee
  • X-ACTO™ knife

© Insulated wire connectors (if you are installing a new JAMMA harness)

  • Carbon paper
  • Saber saw
  • File
  • Bandsaw
  • Tape or glue Road Riot 4W'D Universal Kit

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Road Riet 4WD kit serial number, part number, and description of the missing or damaged parts, and date received.

Preparing the Cabinet for

the Kit Installation

WARNING Te aveid electrical sheck, unplug the cabinet while installing the kit, After installation, plug the game enly into a grounded 3-wire outlet.

Figure 1-1 shows almost all kit parts installed in a typical cabinet. Use this iHustration as a guide while you install the parts. i. Turn off power to the game, and unplug the power cord, :

NOTE The four holes in the corners are not shown in this illustration. Dritl these holes wherever space permits.

0.912" Bia, (4 places} 1.78" Dia,

Figure 1-2 Locations of Control Panel Holes to be Drilled

Page 15

Road Riot 4WD Universal Kit

  • Remove the following from the cabinet:
  • Existing PCBs
  • Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA}— compatible, Table_1-3 on the previous two Pages assumes you have an available game cabinet with a JAMMA harness installed in it. © Control panel decals, labels, and controls
  • Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new deeals.
  • Video dispiay (monitor) shield, display bezel. attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet. if required:

Assembling the Control Panel

Parts Needed from this Kit To assemble the control panel, you need the control panel hele-curting template. which is printed in Figure 1-3. Cut out the template sheet from this manual. You will also need the following pasts from the kit: © Clear cover for the control panel ¢ Control panei decal *¢ Green START button assembly

  • Red steering control decal
  • Contre! mounting bracket
  • Game instructions label
  • Steering control © Four #%-24 x x"-long black carriage boits, flat washers, and nut/washer assemblies fer the steering control
  • Four 10-24 x %-leng black carriage bolts, Mat washers, and nut/washer assemblies for the corners of the control panel cover

Installing the Parts

  • Using carbon paper. transfer the steering control meunting pattern from the template to the control panel. Save the template. Also refer to Figure 1-2 or 1-3 for the exact locations of all contrel-panel holes.
  • Drill feur %s" holes in the metal contro! panel for the steering controi mounting bolts.
  • Drill two 4" holes in the metal contre! panel for the start button’s mounting screws. installation:
  • Using a saber saw, carefully cut out the large hole for the steering control and the smaller hole fer the start button, Deburr the sharp edges with a file. wn Lay the plexiglass cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the button holes as close as possible to the locations shown on the template. Lastly, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners~~wherever space permits. 6, Using a bandsaw, cut the control panel cover to its correct outside shape.
WARNING Wear safety glasses when drilling the plastic control panel cover. Use care to avoid shattering or chipping the plastic.

7% Tape or glue the template to the plexiglass cover. To start the saber saw cut, drill a 1/2" hole inside the steering control hele and the start button hole.

  • Saw out the large steering control hole and the start butten hole.
  • Drill the four 4" holes that will be used to mount the cever to the control panel and the holes to mount the steering control and start button.
  • To prevent injury, carefully deburr all the edges of the plexiglass cover. Fastall the control panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls, Mount the instruction decal on the control panel.
  • Install the cover on the control panel with the four 3/4"-long carriage bolts, washers, and locknuts,
  • install the steering centre! using the 3/4"-long carriage bolts and #4-20 nut/washer assemblies,
  • Install the start button assembly as shown in Figure 1-1. For maintenance and servicing informatien on the steer~ ing control, refer to Chapter 3 of this manual,

At

Page 16

Installation:

Installing the Foot Pedal

Parts Needed from this Kit

To install the foot pedal, you need the foot pedal holecutting template (see Figure 1-4 at the end of this chapter). Cut out the template sheet from this manual. You will also need the following parts from the kit:

  • Foot pedal assembly
  • Four fender washers and locknuts

Installing the Parts

  • Tape the foot pedal template to the lower right corner on the front of the game cabinet (see Figure 1-1 for general placement). Refer to Figure 1-4 for the exact location of the foot-pedal holes. Using carbon paper, transfer the foot pedal mounting pattern from the template to the cabinet. Save the template.
  • Brill four %" corner holes and a 1%" center hole in the cabinet front.
  • Feed the pedal harness through the large center hole. Insert the foot pedal’s threaded studs into the four smail corner holes.
  • From the inside of the cabinet, install the four fender washers and lecknuts onto the threaded studs of the pedal. Plug in the pedal harness connector.

Connecting the JAMMA

Harness

  • If your game cabinet dees not already have a JAM- MA harness, install a JAMMA harness in the cabinet (optional, Atari part no. A046501-01).
  • Install the square split beads on the harness as close to the PCB edge connector as possible. Hold the beads on the harness with the tie wrap included in the kit Road Riot 4WD Universal Kit
CAUTION You must install the JAMMA filter board and the split beads en the JAMMA harness to meet FCC requirements.
  • Using Table 1-3 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.
WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose cennections, oxidation, or a Tire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Read Riot 4WD kit requires +5V and +12V. If SV is available, it should be used, too, Tie off any other voltage wires on the power supply besides +5V, ~5V, and +12V. There is more than ene wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring.

Connect the wires designated for the red, green and. blue video guns along with the sync and ground wires, according to Table 1-3.

Connecting Coin Door Wires i. Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.

  • Connect one terminal of the door lamps to one of the GND wires. Connect the other terminal of the door tamps to the R wire supplying +5V.
Page 17

Road Riot 4WD Universal Kit

NOTE Do not use’ -5V for the coin door lamps. ~5V is required for audio.

Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.

Connect the steering control harness and the start buttoni harness to the JAMMA harness using crimp splices or butt soldering, according to the information in Table 1-3.

Grounding the Cabinet

Find the ground lead (green) of the 115V input power line. -Connect-this lead in daisy-chain fashion to a bare metal part-of the cein deor, the control panel, the video dispiay,-and: the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of piayers, you must connect the green ground wire as indicated above. ‘

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power t@ the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Vols on pins F and 6; and ~5 Volts on pins E and 5. Check that the video dispiay and the attraction lamp have power. Now turn off the power to the game.

Installing the Road Riot

4WD Board Set

After you have checked the power on the JAMMA connector (above), install the Road Riot 4WD board set in the cabinet, by following these steps and referring to Figure 4-4:

  • Use the three #6-32 x %" long screws to connect the game PCB to the PCB grourd plane and mounting plate,

2. Plug the JAMMA filter board"onto the front of the

game PCB, and mount it to the ground plane using one #6-32 x %" screw provided in the kit. Installation

3, Use two #6 x %" screws and the two #6 x %." spacers to connect the game PCB into the back side of the drawer, 4, Then, use the two #6 x 4 screws to mount the mounting plate into the front of the drawer. 5, Plug the JAMMA harness into the filter board, Secure the JAMMA harness away from the PCB with cable ties,

  • Turn on the power to the game, Check that the game PCBs function. If a video picture is not present, see Chapter 3,

Installing the Bezel, Decals, Labels, and Attraction Assembly

decals, labels, and attraction assembly are shown assembled in a cabinet in Figure 1-1,

Installing the Display Bezel

Find the black cardboard display bezel in the kit. This bezel can accommodate both 19-inch and 25-inch viceo displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required.

Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC compliance label (part no, 039450-01) on the back of the cabinet.

Installing the Side Panel Decals Find the side panel decals in the kit, Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decais as shown in Figure 1-1. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Page 18

installation

Installing the Attraction Assembly Find the Road Riot 4WD attraction shield and the attraction panel film in the kit. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1,

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings. If you have linked two game cabinets together, you must set both players to the same difficulty setting, or the game will not functien properly after turning on the power. If the settings don't agree, you can change them both to medium by pressing bath start buttons at power-up. You can also use the Game Options screen in the self-test to change the setting.

NOTE The factory-recommended cain option setting fer “Discount to Continue” should be set to Yes (see Tabie 2-3 in this manuai). Making your game match ail the recommended settings results in a setting of 2 coins to start/1 to continue. We highly recommend this increase in price per play, toe maximize your return on investment. However, this setting may not suit all locations.

M: imizi E : gs

For maximum earnings, regularly maintain your Road Riot 4WD game following the instructions in Table 3-1, in Chapter 3. When you set up the game and when you collect money, perform the automated self-test and check the controls with the Switch Test in the self-test.

Game Play

This section describes the features and driving of the Road Riot 4WD” game.

1-10 Road Riot 4WD Universal Kit

Introduction Road Riot 4WD presents off-road racing competition combined with combative shooting action. Players drive highperformance off-road vehicles armed with a stun gun.

Road Riot 4WD is a oneplayer off-road racing game kit where players can compete for an overall season championship. Controls in this game include a start button, a gas pedal, and a steering control with wigger buttons. Players are challenged by the lifelike skidding and bouncing action of their fourwheel-drive vehicles on the track. The cars can also crash in several different ways, depending upon how an object is hit. The cars can rell on their sides, fly end over end, or even explode on impact. Twelve different wacks offer special terrain and competitor challenges. Each track has a different. background, ranging from desert to mountains, corn fields to ice fields. Terrain and track obstacles vary for each setting. Video graphics are digitized pictures of real-life objects. The Road Riot 4WD racing vehicles, people, and obstacles on and around the track are realistically depicted, The life-like detail and humorous interaction with the video graphics enhances player appeal.

Two-Player Linked Game Play i

Two games can be converted and linked together via the optional link kit assembly (available from your dis. tributor). The linked configuration encourages twoplayer competition; players can also choose to play individually. if two games are linked, there are several incentives for two-player simultaneous play. Two players can compete head-to-head against each other for the season championship of 11 different race courses. The road riot will continue as long as the player defeats the hosting opponent's yellow cars. If two players are playing a linked game, there is one less computer-controlled car to beat. Two players can cooperate to beat the opponent cars.

Page 19

TOULNOS ONIUAALS A-X

Ssanwvo5 Purd [ONTED 1 GAY Jory peey Joj aejdussy Samng7-sjoH ¢-T ams

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

Road Riot 4WP Universal Kit Installation

NOTE Place the foot pedal as low as possible against the bottom right corner of the cabinet.

FOOT PEDAL HOLE PATTERN

Figure 1-4 Hole-Cutting Template for Road Riot 4WD™ Kit Foot Pedal

1-13

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

CHAPTER 2

Self-Test

INTRODUCTION

Use the Road Riot 4WD” self-test to check first set up the game, each time you collect

the condition of the game circuitry _. the money, or when you suspect

and controls. You will see the self- game failure. @ This chapter test information on the video dis- shows the screens in the self-

play and hear the sound test in- test and explains each of the fermation through the speakers. tests. The screens and expla- You de not need any addition- nations are arranged in the or-

der they appear in the self-test. Table 2-1 lists all of the self-test

screens and their purposes.

al equipment to perform the

self-test. 4 You should per-

form the self-test when you

Page 24

Self-Test

the Self-Test

To enter the self-test, turn on the self-test switch on ted inside the coin door (if you wired your kit that way). The JSA III Audio PCB also has a These two switches are wired in parallel, meaning that you can use either one indepen- Exit the self-test by switching off any of the the bracket Ic

self-test. switch on it.

dently. self-test switches.

Self-Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the list by pressing the left and right triggers; the corresponding test is highlighted in blue. Choose the screen. q os: by pressing the START button.

Adjust Volume

Adjust the volume of the game using this Control the volume by pressing the volume number increasshown in Figure 2-2. the left and right trigge Road Riot WD Universal Kit

SELF-TEST

AOJUST VOLUME

GAME STATISTICS.

COIN OPTIONS GAME OPTIONS

ALPHA TEST MOTION OBJECT TEST PLAYFIELD TEST

SWITCH TEST

COLOR TEST CONVERGENCE TEST

SOUND TEST ASIC65 TEST OSP COMM TEST DSP LINK TESTS. COMPLETE RAM/ROM TEST

13 NOV 1991 17:45: 13 NOV 1994 15:49: SELECT START PRO! TRIGS

Figure 2-1 Self-Test Menu Screen creen, the gas pedal. Save the new volume and return to the self-test menu by pressing the START button. es or decreases. To restore the old volume fevel, push

Screen Use or Purpose

Game Statistics Screen

Cain Options Screen

Adjusts the volume. _Displays the game statistics ” Use to set and check the coin options settings.

Game Options Screen

Alpha Test Screen Motion Object Test Screen

~ Use to test tor clarity ‘oft characters

Playfield Test Screen Switch Test Screen Color Test Screen

Convergence Test Screen White Convergence Screen Violet Convergence Screen Green Convergence Screen Sound Test Screen ASICES Test Screen DSP Comm Tests Screen Use to set and check the game options settings.

Use to test the movement and color of game objects. Use to check the playfield displays. Use to display the functioning of the game switches and controls,

Use to check the video display color circuits, A series of screens to check and adjust display convergence. Use to check and adjust video display convergence of red, biue, and green Use to check and adjust video display convergence of red to blue. Use to check and adjust video display convergence of red and biue to green. Use to check the audio circuits. Use to test comm port, checksum, and internal RAM. Use to check the communications hardware (works only if you have installed the optional fink kit). DSP Link Test Use to test the transmitting and receiving of data between two finked games (works only if you have installed the optional link kit) Compiete RAM/ROM Test Screen Use to check the all RAMs and program ROMs.

Table 2-1 Summary of All Self-Test Screens

Page 25

Road Riot WED Universal Kit

ADJUST VOLUME

VOLUME: 15

vue

USE TRIGGERS TO CHANGE VOLUME PUSH PEDAL TO RESTORE OLD VOLUME PUSH START TO NEW VOLUME AND EXIT

Figure 2-2 Adjust Volume Screen

Game Statistics

Use the information shown on the statis reen, in Figure 2-3, and’on the histogram screens to keep track of your game use and maximize your profits. Record the information on the Road Riot 4WD statistics page in the back of this manual. ‘The statistics are collected from the last time the statistics were cleared. You can clear the statistics by pressing both Wiggers at the same time, Press the START button to leave this screen and go to the histograms. © Left Coins show the number of coins counted in the left coin mechanism

  • Right Coins show the number of coins counted in the right coin mechanism.
  • Aux Coins shows the number of coins counted on the auxiliary coin input © New Gamesis the number of new games played.

Statistics Left Coins Right Coins Aux Coins New Game Continuation Free Games Idle Time Active Time Solo Time Linked Time Error Count Total Credits Total Coins

PRESS BOTH TRIGS TO CLEAR STATISTICS

PRESS START FOR HISTOGRAMS.

Figure 2-3 Game Statistics Screen

  • Continuation is the number of continued games. played. © Free Games is the number of free games played if Coin Option set to free games.
  • idle Time shows the number of minutes the game was not being played. © Active Time is the number of minutes the game was. being played in any mode. ¢ Solo Time is the number of minutes a ing held in single-player mode. ace Was be-
  • Linked Time is the number of minutes a race was being held in two-player mode. © Error Gotott shows the number of rs counted in the erasable memory. If you have an error count, the stuistics may be wrong. If you consistently have errors counted for several weeks, replace the SEROM at 38F.

Histograms

‘The histograms are (vo screens that contain information about the game. Press the START button to move to the next histogram. ‘To clear all histograms. pi both trigg while displaying the las! ogram screen. Press START to exit from the last s

The first histogram shows new game times. and the second has continued game times.

Coin Options

Check and select the coin options on this screen, shown in Figure 2-4, Yo move through the options. use the right trigger. Change the option in yellow type. The factory default

COIN OPTIONS. (DEFAULTS IN GREEN)

FREE PLAY: NO DISCOUNT TO CONTINUE.

BONUS FOR QUANTITY BUY-lI NONE RIGHT MECH VALUE: 1 COIN COUNTS AS 1 COIN LEFT MECH VALUE. IN COUNTS AS 1 COIN

PRESS RIGHT TRIGGER TO SELECT OPTION LEFT TRIGGER TO SELECT SETTINGS PRESS PEDAL TO RESET FACTORY OPTIONS. PRESS START TO SAVE SETTINGS AND EXIT

Figure 2-4 Coin Options Screen

2-3

Page 26

Seif-fest Road Riot AWD Universal Kit

s tings Explanation

Ditticulty Level*MediumEasy Easier EasiestEstablishes degree of game difficulty,

Hardest Harder Hard Medium Hard

Car ColorRedy¥BlueLets you display each player's car in a different color

(used only in a linked, two-game setup).

Music in AttractYes ¥NoLets you choose whether or not to play music in the

attract mode.

Clear High Score TableYesNowLets you clear the high score table.
Auto High Score ResetEnabiewDisabieAutomatically resets the high scores to the factory de-

faults after 2000 games, unless a player has entered

his initialswithinthious200 games.

“If you have linked two games together, you must set both players to the same difficulty setting or the game will not function property after turning on the power If the seltings don’t agree, you can change them both to medium by pressing both START buttons at power-up. You can also use the Game Options screen in the self-test to change the setting. Vv Manufacturer's recommended settings. These settings are shown in green on the screen.

Table 2-2 Game Option Settings

settings are shown in green. To change 4 the left vigger. To save the new settings. press the GAME OPTIONS START button. This returns you to the select tes! (DEFAULTS IN GREEN) sereen. If you want to keep the original settin, DIFFICULTY LEVEL though you have changed it, press the pedal MEDIUM brings back the original factory setting. Use the button to exit. ting.

The coin option settings and factory defuults are ex- MUSiC. IN'ATUBACT:

plained in Table 2-3. CLEAR HIGH SCORE TABLE: : NO

Game Options AUTO HicH SCORE ALSET

Check and select the game options on this screen, ; shown in Figure 2-5. T SETTINGS

To move through the options, use the right wigger.SSPEDALSET FACTORY OPTIONS

Change the option in yellow type. The factory default VE SETTINGS AND EXIT settings ire shown in green. To change a setting. press the left tigger. To save the new settings, press the Figure 2-5 Game Options Screen START button. This returns you to the select test screen. Hf you want to keep the original setting, although you have changed it, press the pedal. This brings back the original setting. Use the START button to exit. The screens display all of the alphanumeric sets, If the screens are not clear, you have a problem. ‘To move through the screens, press gither the left or right trigger. Use the START button to exit. The game option settings with factory defaults are

shown in Table 2-2. Motion Obj ect Test Alpha Test The motion object test screen, shown in Figure 2-7%

tests the movement and color of various game objects. The alpha test consists of a series of screens that you use to test the clarity of characters. Figure 2-6 shows the first of the alpha test screens. Select the test function with the START button. Use the pedal or steering control to move objects, change pictures, and change object size. Press the START button to Move to the Next test or exit,

Page 27

Road Riot 4WD Universal Kit Self-Fest

Ss ngs Explanation Free Play Now Yes Set this to “Yes” for demonstrating the game. Discount to Continue No Yes vw Lets you offer a reduced price per credit when players want to Continue é a game. Game Cost 2coins 1 creditw 8 coins 1 credit Bonus for Quantity Buy-in None v 2 coins give } (extra coin) 3 coins give 1 3 coins give 2 4 coins give 1 4 coins give 2 4 coins give 3 5 coins give 1 & coins give 2 5 coins give 3 6 coins give 1 6 coins give 2 6 coins give 3 7 coins give 1 7 coins give 2 7 coins give 3 8 coins give 1 BS coins give 2 8 coins give 3 9 coins give 1 S coins give 2 9 coins give 3 “Lets you choose various leveis of bonus coins or no bonus.

Right Mech Value 1 coin counts as 1 coin # 1 coin count as 8 coins

Left Mech Value 1 coin counts as 1 coinw

Manufacturer's recommended settings. These settings are shown in green on the screen. Is the number of coins each coin counts as in the Is the number of Coins each coin counts as in the tight coin mechanism,

left coin mechanism.

Table 2-3 Coin Option Settings

Figure 2-6 Alpha Test Screen

Page 28

Self-Test

Figure 2-8 Playfield Test Screen

Playfield Test

This test. shown in Figure 2-8, checks the condition of the scrolling playfield. Move the steering control left/~ tight to see horizontal movement on the screen. Hold the right tigger button while moving the control left/right to see vertical movement. Press the START button to exit the test.

Switch Test

The switch test altews you to display the status of the game switches and controls. The switch test screen ap- Pears in Figure 2-9. The items tested are:

  • Steering wheel ieft/right movement
  • Foot pedal potentiometer © Left trigger switch
  • Right trigger switch © Start switch and start lamp As you activate each switch or control, make sure the correct words are highlighted in blue on the screen. If players complain of cars driving erratically, or whenever the control hamess is unplugged, you must recalibrate the controls. Follow this procedure to do the calibration:
  • Press the right trigger and » ously. The numbers after WHE! screen will change. int button simultane- Land PEDAL on the
  • Turn the steering control to its right limit. and hold it there for 4 seconds. Then turn it to its teft limit and hold it there for 4 seconds.

2-6 Road Riot 4WD Universal Kit

SWITCH TEST.

oe | WHEEL RIGHT/CERT: summa PEDAL

LIMITS WHEEL PEDAL EG Bei ai (AB GA

LRG. RERIC START PRESS RTBIG AND START 10 @ PRESS LTHIG AND HY RIG TO EXT

Figure 2-9 Switch Test Screen

» Press and hold the foot pedal for 4 seconds. 4, Simultaneously press both triggers to save the calibration and exit from the switch test. Do not simply turn the self-test switch off to exit from this test: doing so will not save the calibration.

Color Test

This test indicates the dynamic range of the video display color circuit in a series of seven screens. The first color test screen is shown in Figure 2-10. Advance to each screen by pressing the right trigger (the software cyeles through all seven screens and then starts over again). The screens are as follows:

  • Red at the top, followed by green, blue, and white
  • Yellow at the top, followed by light blue, purple, and white

Figure 2-10 Color Test Screen

Page 29

Road Riot 4WD Universal Kit

  • Solid red
  • Solid green
  • Solid blue
  • Solid white

7 Solid gray If the screens do not match this description, adjust the video display as described in the video display manual. Press the START button to exit.

Convergence Test

The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-11. fo see the violet and green screens, press the right trigger. Press the START button © go to the test select screen.

Check the following on the screens:

  • The grid lines should be straight within 3 mm, and the lines should not pincushion or barrel.
  • The convergence of the lines on the violet and white screens should be within 2 mm. If the screens do not meet these ¢ djust the video display as described in the video display manual.

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-12. » the steering wheel control to select the sound, and press the right tigger to listen to it. Pressing the left trigger stops the sound from playing. Press the START button to return to the select test menu.

Figure 2-11 Convergence Test Screen Self-Pest

SOUND TEST 4 8 10

NUMBER OF SOUNDS: 61 SOUND CPU STATUS

COIN MECH SWITCHES ; LEFT RIGHT 0 Q

Figure 2-12 Sound Test Screen

ASIC65 Test

Use the ASICG6S test screen to test the comm port, checksum, and internal RAM. The first screen is shown in Figure 2-13. You can select one of the three options shown. Use the left trigger to move to the next option. Use the right rigger to select an option. If you test the comm port, a message indicates whether or not it's OK. The checksum option displays the checksum. The internal RAM test indicates whether or not the RAM is OK. Press the START button to exit.

Figure 2-13 ASIC65 Test Screen

2-7

Page 30

Self-Test

DSP Comm Tests and DSP Link Tests

NOTE These tests only apply if you have in- Stalled the optional link kit, to link twe upright game cabinets tegether. The Comm Link board is part of the link kit.

Each of these two main tests has several sub-tests that are selected frem menus. These twe main tests are described in more detail in the supplement included with the link kit, CO-373-01. Road Riot 4WD Universal Kit

Complete RAM/ROM Test The RAM/ROM test checks both RAM and ROM, If the test passes, you will see a sequence of color screens, and then the self-test menu screen will reappear. If the screens turn to black and white or gray or if no message appears, the RAM is bad; you will need to replace it. If the ROM is bad, the checksum of the bad ROM is displayed. You need te replace that ROM. Press the START button to exit,

Page 31

CHAPTER 3

Troubleshooting

~ and Maintenance

INTRODUC

This chapter contains troubleshoot- Za

ing tables and repair circuit boards, and a

list of ROM-caused

problems, with speprocedures for your <@amggeg= FN OD, cific ROMs to check Road Riot 4WD™ game. The

chapter has two parts. The first part contains three troubleshooting tables. The tables contain general troubleshooting information, the voltage levels and test points on the printedand replace. @ The last part of the chapter has information about connecting the video display (if it requires separate positive sync) and repair information for the steering and foot pedal controls.

Page 32

Troubleshooting and Maintenance Road Riot 4WD Universal Kit

Problem Suggested Action Coin Mechanism Problem 1. Check the wiring to the coin mechanism.

  • Check the voltage to the + side of the mechanism.
  • Test the coin mechanisms with the sound test screen in the self-test.

Game Play Problem Check the harness and connectors. . Perform the self-test. Check the voltage tevels on the PCB. See Table 3-2, Voltage inputs and Test Points. . Check What ROM Problems Look Like, Table 3-3, for specific ROM preblems, ROMs

Steoring/Foot Pedal Problems 1. Have the controls been tubricated with the correct type of lubricant? If not, lubricate them shown in Figures 4-2 and 4-3,

  • Check the harnesses and connectors.
  • Check the switches on the control.
  • If you took the control apart, have you reassembled it correctly?
  • Make sure all the parts on the contro! are in good repair. Repair or replace parts.
  • Reset the limits on the steering control and the foot pedal. Sound Probiem 1. is the speaker volume turned up? (Volume is adjusted digitally in the self-test.)
  • Check the voitage on the JAMMA connector.
  • Check the wiring from the PCB to the speaker.
  • Check the voitage level to the PCB. See Table 3-2, Voltage inputs and Test Points. 5, Replace the speaker. Video Display Problem Screen is dark. Is the game plugged in? Is the game turned on? |. Are the connections good? Js the line fuse good? . Is the display brightness turned up? . Are the solder connections on the line filter and transformer good? . Is the JAMMA connector on the PCB tightly connected? . Check ail of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry. See your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?
  • Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signa! voltage is 0.5 to 3.5 Volts.)
  • If the level is not correct, check the connectors and the harness. 2 N ONRwON-

Only a colored screen appears. You probably have a serious RAM probiem. Display area wavers or 1, Bo you have correct power voltage to the video display PCB? is too smali. 2. Bo you have correct high voitage to the video display? Picture is wavy. 1. ts the menitor ground connected to the monitor?

  • Are the sync inputs connected properly? Picture is upside down. When you serviced the display, you connected the wires incorrectly. Switch the horizontal or vertical yoke wires on the display, Convergence, purity or color problems. Use the screens in the self-test to adjust the video display. Use the adjustment procedures in your video display manual. Picture is not centered. Use the centering procedures in your video display manual,

3-2 Table 3-1 Troubleshooting Table

Page 33

Road Riot 4WD Universal Kit

‘Troubleshooting and Maintenance

VoltageTest Point or LEDSource and Purpose
+5 + 0.25 VOC+8V1Logic power from the switching power supply.

CR3 LED (Game PCB) Lights when 5 V is applied to the PCB and the reset (RST} jumper is open. CR9 LED (JSA Audio Ili PCB) Lights when the +12 V supply is good. CR3 LED (JSA Audio Ili PCB) Lights when the -5 V supply is good.

+12+VOP (pin 4 of LM324)+12 V from the switching power supply. Positive supply for the analog

circuitry.

5V—VOP (pin 11 of L324)-5 V from the switching power supply (if connected). Negative supply for

the anaiog circuitry.

Table 3-2 Voltage Inputs and Test Points on the PCBs

Problem ROM Causing the Problem Check the ROM at:

Program works, but motion objects orGraphics ROMsPlayfield: 20C-22C, 20D-22D. Motion

playfield is wrong. Object High: 28-98. Motion Object Low: 2P-9P. Alphanumerics: 22U

Garbage on screen: program doesn’t work.Processor14B/C

Program ROM 0 8C, 8D

Game program is erratic.Program ROM 19C, 9D
No sound or erratic sound.Audio Program120

Audio ADPCM 12E, 15E, 17E, 19E

Table 3-3. What ROM Problems Look Like

Video Display Sync

Problems

This game board provides separate positive horizontal and vertical sync on a separate connector, for monitors that will not work with the composite negative sync signal provided at the JAMMA edge connector. This connector (labeled “Sync”) is located near the edge connector. Pin 1 is horizontal sync, Pin 2 is vertical sync, and Pin 3 is ground.

Troubleshooting

The tables in this chapter (3-1, 3-2, and 3-3) can help you troubleshoot problems in your game. The troubleshooting tabie lists possible sources of problems in various parts of the game. The voltage inputs and test points can heip you troubleshoot PCB problems. The ROM problems table can help determine exactly which ROM might be causing game play problems.

Removing and Replacing the Steering Control

The steering contro! is shown in Figure 4-2. If you want to repair the X-Y steering control, disassemble it by removing it from the control mounting bracket (pod) on the contro! panel. The hardware that secures the pod and steering control is shown in Figure 1-1,

inal Pin Signal

Red7GNB
2GNDGNO
3KeygNeg. composite sync
“4Green10Positive
7GND11Positive H sync —

6 Biue

Table 3-4 Atari Games Video Connector Pin Assignments

3-3

Page 34

‘Troubleshooting and Maintenance Road Riot 4WD Universal Kit

Removing and Replacing the Foot Pedal Assembly

The foot pedal assembly is shown in Figure 4-3. if you want to repair the foot pedal, disassemble it by removing it from the front of the game cabinet. The hardware the secures the foot pedal is shown in Figure 1-1.

ROMs and RAMs only a colored screen and cannot

. . enter the self-test, see Table 3-4.

you have a ROM problem, see Table 3-3. If you see and RAMs on the game PCB, see Figure 4-5.

Page 35

CHAPTER 4

Parts Ilustrati

PRODUCTION

This chapter provides infor-

mation you need to

order replacement

parts for your kit.

Common hardware parts, such

as screws, nuts, washers, and so on, are

included in these parts illustrations. @ When

you order parts, give the part number, part

name, the number of this manual, and the serial number of your game. With this infor-

mation, we can fill your order

rapidly and correctly. We hope

this will create less

downtime and more

profit from your

games. Atari Games Customer

Service phone numbers are listed on the

inside front cover of this manual.

Page 36

Parts Ilfustrations - Road Riot 4WD Universal Kit

Hems Not Shown:

Aotroeeot Conta! nerconneet amass Assy 141026-001, Forte Bone places} 1.20 tanpor prea TORK rampar pre 049776-05 peeled Atacton Fim | 1-19 Tampor-proa! TORK Key oastseat Product LD. Leber 999450.07 FCC Compliance Label 176128002 ‘8432° Tamper-Prool Hex Key Driver 76602-002 10-24 Wire & Cable Te THs load Riot 4WD Universal Kit Inslaiation instructions.

049776-01 Sid Panel Doc! 2 places)

‘A949815-01 Road Fo! AWD Board Set osangs-01 PCB Ground Plane anasesos = 8 \ : and Mounling Piste Asay. (wo am . Us Taeatae ip N02 x a" = Ss : S| | Penta Screw {3 places) 175004-708 Fiber Washer

114-20 Polymer ax Locknt paces) 114-20 Countersunk Serow > > JAMIA Finer Board Assy. (4 places) ‘| eonosna

(2 places) aee01s-0118 #6 Lock Washer (4 pieces)

Foot Pedal Assy. 77010-2848 #1/6-20 Poymer Hox Locknut (4piacos) as-07002 10-24% 34" Carriage Balt Va Fender Washer paces) Conttl Panel Cover — .

Controf panet in closed position

Figure 4-1 Parts of Road Riot 4WD Universal Kit A4049868-01 C

4-2

Page 37

Road Riot 4WD Universal Kit Parts IMtustrations

f 407027-001 Lihium Grease

A049948-01 " Foot Padal Harnoss Assy

176065-100 4° Tie Wap

  • 72-8808 I | eae v2 Soot Brew I re918s. £48.92 Hox Nut

Link Bracket

75-048 #9 Spin Lock Washer @ places) 72.1806F 18.39 + 28" Pan.He Seraw 2 places)

Figure 4-2 Foot Pedal Assembly A043825-02 D

Page 38

Parts Illustrations Road Rist 4WD Universal Kit

178247-G03 178248-00' Switen Bracket _ Trigger

_f 17B249-409 | Right Handie Cover

Figure 4-3 X-Y Steering Control Assembly A049454-03 B

Page 39

Read Rict AWD Universal Kit Pans Ulastrateations

72-8012 | 10-82 x 344" Socket Hd. Cap Scraw povmmrrnennnn 7800-0 #19 Flat Washer 7] 048861-01 | NOTE: The Shattis part of the | XY Steering Mod Seraw | Frame Woldment (049482-07). | 106007-001 | t Sn Loctite 290 Green Adhesive | 2 places)

ved AOSQA62-01 0a7ag5-01 i " Shaker Control Hamess Assy. OvFing Stop | : 178223-006 | $49.10. x .103W 1") 12-133) O-Fiing @ places) | |

(49758-01 Base Flange Bearing 107027001 Lthiurs Grease TACT B04 6-32 x 1/4 Washer Hexctid, Sorew @ places}

171100-002 Lett Hang Kt Assy

76-081202 .780 Bearing . : 97027-0091 peeas2-GF as Z 2 : Lthiusn Grease Lubricant Frame Weldment

£178284-0608 | 0 Tabi ogsass-o1/ ff . Tubing Cover j A | foerasaot 9 : a Shaft Waidment 097480-01 _Pivot Shaft Torsion Spring 479027-005 FP Nyoge! Luts

| pazanr.os Spnog Catch 47181-7808 6 Cioaranee Stee! Spacer (2 places)

097479-01 Pot, Bushing 471309-001 Flight Haale Kit Assy.

| { 17000-138 Leora 882 Hex Mut 78081-3608 6-32 x 12 Tamperproot Butlon-Hd. Screw Potartiomete é piacas) 105007.001 72-8808 193008-1001 F shear 4 5K Ohm P 178012-001 | B-32 x 1/2 Socket-Hd, Cap Screw

750 Retaining Ring

Figure 4-3 X-Y¥ Steering Control Assembly, Continued A049454-03 B

Page 40

Parts Hlustrations Road Riot 4WD Universal Kit

NOTE Hems marked with a are not part of this Board Set Assembiy. Circled numbers refer to assembly steps described on page 1-9. Steps 5 and 6 are not shown in pc ‘5 @ 172-6208 + this iltustration. 6x 1 4/2" Screw

Fiber Washer (2 places) 178020-812 + #6 x 13/96" Spacer (2 places)

178171-1612 86-32 x75 Alum, 1/4" Hound Standoff 72-16068 86-32 x 3/8" Pan-Hd, Screw (2 places} 175017-3013 46 Split-Lock Washer : (2 places} 175014-2021 72-6608S + |@ 1¥6 Flat Washer #6 x 12" Screw @ | 72-1612 + (2 places} (2 places) 46-32 x 3/4" Lg. Screw (3 places) A049292-01 i . 175018-0113 « JAMMA Filter Board Assy. i : : #6 Externat Tooth Washer 72-1606F + @ places) #6-32 x 38" Screw 049866-01 175014-1025 + 175015-0113 ¢ i PCB Groung Plane #6 Flat Washer #6 External Tooth Washer & Mounting Plate (3 places) 175014-1025 « #6 Fiat Washer

Figure 4-4 Road Riot 4WD Board Set Assembly A049813-02 B

Page 41

8 gol Sa a Og 80 fi = qa Cae = tye ~ 22 i GF cece ao oF: 0 a eal a 40 Cao Se ee eo = : ada, i =f SUSI Sed em. = ‘Sega Cet (gs | [a= piace beasicate OCA SO no Ce CECE [p= ae bo [ej “8 cm eee

oe nets 2P pin 22 to 118, pin 3. However, , you should have ne modification wire on tt 2S through 58. In that case, that conr

NOTE: Your Road Riot 4WD Game PCB probably has i ts QP. pin 22 to 11S, pi A049757-01 A Figure 4-5 Road Riot 4WD Game PCB Assembly
Page 42

Road Riot 4WD Universal Kit Parts Ilustrations

Figure 4-6 JSA (JAMMA Stand-Alone Audio) II PCB Assembly A048974-08 A

Figure 4-7 JAMMA Filter PCB Assembly A047292-01 A

Page 43

CHAPTER $3

Schematic

INFRODUCTION

This chapter con- sf The game PCB and tains the schematic Segre JSA TT PCB assemdiagrams for the bly drawings are Road Riot 4WD"™ illustrated in Chap-

game PCB and the ter 4, Parts Illustra

JSA TI (audio) PCB. tions.

Page 44

Schematic Diagrams

coo? COD? reer) C50) f-3y0 crazy) ney cecum ee-tocKe> ferrrrey CAD> > rewR-11 O———+ un CRED) Jere COLUE) JerwR-13 O————s ALU CVI 080) Jeera CSELFTEST) Jarw-15 O——— seLFTEsT COIN.) Jawsi-16 O———* COI, STRATED Jee@R-17 O————» STRIT CUPLAD JmFER-18 O———s UP COOMA JerER-19 o————= on CLEP TLAD epwenz0 Or ERICMLAD serwe-21 Oat CLBUTTON 2 seeen-22 oa actar CLBuTTON2 > aRRRA-23 0» rcras CLBUTTON > JReRR-24 Oe acca CLEFTLBD servan-25 O——— pcTTL CRIGHTLB) JRPR-26 O——e acrTRa COND) JAPR-27 0+ GD ONO) Jeee-28 0-2 0 oxo —— ceno COMECTED AT FINGERS ONLY.

“ wv ares OND) JawR-A O———+ cro COND) Ieew-8 Os can C430) JRew-c O———a oy +50) JRRR-0 O————+ «50 C90) JRR-E Oe “9 420) daewe-F O— $2 320 REY JeMB-H OF ECCNTRRD ARPA J O————a CORTE. CC-LOCKR? JRRR-K O- Caenns-> drem-, O———a sPen- ED ONO? Jenn 0 uD“ CREE) Joe-u 0» DREN SINC) ReeMR-P O— + CORPSE SERVICE? SeeR-R O——— + FERUTEEE TILT) sews O————= Tt CCOINR) SereR-T O———e COINR CSTRRTRD saeeA-U O————w srr? CUPRA) IeeW-V O——— + uP. COOMNRAD JRC O———e ns KLEPTRA? JREPR-K O———a 2 CRIQHTRAD yaneR-T O————a RT? CROUTTONL > LeewMn-2 O————a pez CupUTTONZ > seween-Am O————+ actor ERGUTTONA> snwa-Be o————> acree CLEFTRGD Uewem-co Os ectrce RICHTRE) JARRA-D0 O————+ acttR2 COND) JROPR-EE Os a0 COND) SRAAAFF O———e on

pusvo1re pee 18 O—eactte ty Oe AcrTL? 13 O—ercrci 32 o—ercrea 41 o—eactaa 10 O—aRY3 yO aLrs 3 oan ross eat) 5 o—scoma 4 oe senvices ao 20s. 1 0—2cND

asec Doe ysync.our 2 O—* usin. 0UT 30 — vi0cN Road Riot 4WD Universal Kit

yy rata sve i}soee a og, ope Tt [oo F cn? ow 9 =e TSTPTAE cd

ot exis oft cxniza of? cma) craw) of? cas) of cme okt car) ote me of caning 0-20 cxneo> Sa

Page 45

Road Riot 4WD Universal Kit Schematic Diagrams

nae an

Fond

‘SERVICER

J eat on OTE woe OR oe

rw S-TEST

SELFTEST pert)

PRY 3 40 PRE a

are we au ra bia] Feu

sz, ti 20723R ea mah Fae Foo ;

o-ageangat0:42

Figure 5-1 Road Riot 4WD Game PCB Assembly Schematic Diagram 049756-01 B

Page 46

Schematic Diagrams Road Riot 4WD Universal Kit

Per bites: ne Mo gyjarzoe By [sso = [2 xps3, en iO rs t a _ay L Tar cee car 29 cz caers Te ial i Ts ya re St Tee oo0

assy RG Ro? SRE SUT 1 ee Tes 470 Fu70 F470 irae the mo ames, it i 2 ts 4 =_ a Ac. es LE rape

  • cu sey re Fa aK u

oo

ven

ae rreve 2) So! eo raree Fo4

on 13.10 vanes c

  • ROIS foc ‘rons 8 os
68.RD13matedhad
tootesc305
ss.ro10 ="aufonesoe
tare o— 2Foswanecoe EE#20, t0¢

68.age—24] ay 60.01 —— 22] ho 21 ross

=tte_—NE0%

‘OEsTATIS »—2q Be ee NS Ee

-IOSaj
Afcemmaaercrecana Eva?

ths oy OTR ox 0 EE] tno 8

Page 47

Road Riot 4WD Universal Kit

g (7 :

strvices =

n3 rcrt3® ura actTa3 SESeeess” ar Fs

acTTu « acres aCtTRe © FcTes » ctr CTA © actin starra

‘CONTR

Figure 5-1 Road Riot 4WD Game PCB Assembly Schematic Diagram 049756-01 B Schematic Diagrams

xocos1s2

e-as-a9ena2:53

5-5

Page 48

Schematic Diagrams Road Riot 4WD Universal Kit

oe aN

Page 49

Road Riot 4WD Universal Kit Schematic Diagrams

PoCourerersy

Figure 5-1 Road Riot 4WD Game PCB Assembly Schematic Diagram 049756-01 B

5-7

Page 50

Schematic Diagrams Road Riot 4WD Universal Kit

GND AND AGND TIED INTERNALLY NEAR MEMG295.

5-8

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

Schematic Diagrams Road Riot 4WD Universal Kit

a EREPRERBARIIZ2VT qadgsggsagegg22zs

veers

od vy iL rata 1a pr pao } 36 won Be msrecrs week Ds lead an fe are a ce ace 2 Ss nes OES

  • & a ae ats ss oe ae ise x 1 mt = 2: & se = 7 By
= BSbse
se nOop |B _v0?ghtme Les vor
eps pry ReD6] =Soe ‘Del vibod
ee RoosF2Ses
UPREO. se aeDs uyas Deaa
ORTRES « ‘RETT ae‘DalAs 08]
me aa1a
= = omFA.

& FE) bs ot

1oe

5-10

Page 53

Road Riot 4WD Universal Kit Schematic Diagrams

ee

Ss ag iF SERSER :

5S8s8s3

oy

caxiiys

Tift fate] ry PEE EE i F

asanarse

Figure 5-2 JSA Audio III Assembly Schematic Diagram 048973-01 C

5-11

Page 54

5-12 Hlereseesers aqaaret nears nena ictal

i Te Schematic Diagrams Road Riot 4WD Universal Kit

Page 55

Road Riot 4WD Universal Kit Schematic Diagrams

Ld

aortleron

prvpes tae aston cal

soredlsoa}
soxtla40]

soe——ton 30 sme—tl20 20} erem—Zti0 10}

ao-t9919:55

Figure 5-2 JSA Audio II Assembly Schematic Diagram 048973-01 C

5-13

Page 56

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 57

Road Riot 4WD Universal Kit

died JAM-A, J1-2 JAM-B +50 c24 = «2200PF Ji-3 JAM-C HHI cas 2200PF | JAM-D a c26 2200PF 42-5 srt

tev cer 2200PF JA-6 MM _ sar MHA

x & lH Ji-7>- ~<JAM-7

c28 2200PF 34-8) M TMX sates

cea = 2200rF 4-89 atk

Bee FE HH c30 2200PF Jt- £0 at

C34 2200PF Ji-4t en iy, JAM-4

C32 270PF Ja-42 19 9. stn

c33 270PF $4213) sat

cy 2200PF J4-19 1M M$ sar

2200PF Jae en JAM-S MESH IKSHE SHEE HEE +SU

+120 ‘Schematic Diagrams

C36 2200PF JAH26 $MM set

c37>2200PF

J8-47 $n OM sau

C38 2200PF J4-48 9M atv

c34 2200PF J4-19— MM _X sat

cho 2200PF 44-20 1M AM _< sattx

cH 2200PF J4-21 MM MX sty

cue 2200PF 3222 MM _X st-z

cus=2200PF

41-2319 M1 _< Jan-na

cua=2200PF

31-24 FO st L cus 2200PF 4-28 OM 1X st-c

cHe 2200PF J4-26 $MM _X sat J1-27 JAM-EE

J1-28 JAM-FF

HH MHL.

MKAH KH HH

HH

Figure 5-3 JAMMA Filter PCB Assembly Schematic Diagram 047292-01 A

5-15

Page 58

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 59

APPENDIX

Glossary

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE The true state of a signal. For example: The active state for is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation.

ANALOG Measurable in.an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE. The maxinium instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state’ An astabie device will free-run or oscillate.as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momenuary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cat, formed, or machined retention device, such as the conical device used to. mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receiv on the same line (e.g. the data bu: microprocessor)

BINARY ‘A number system that expresses all values by using ovo digits (@ and 1), BIT A binary digit: expressed as 1 or 0. BLANKING: “Furning off the beam on a cathodg-ray tube during retrace. BLOCK DIAGRAM A drawing in which fenctional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER 1, An isolating circuit designed to eliminate the reaction of a riven circuit on the circuits driving it (¢.g.. a buffer amplifier).

  • A device used to supply additional drive capability, Bus An electrical path over which information is transferred from any of several sources to any of several destinations

CAPACITOR A device capable of storing electrical energy: A capacitor blocks the How of DC current while allowing AC current to pass. CATHODE ‘The negative end of a diade,

CHIP An integrated circuit comprising many cir cuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions.

‘COINCIDENCE Occurring at the same time, COIN COUNTER A G-digit lectromechanical device that counts the coins inserted in the coin, mechanism(s),

COIN MECHANISM A device on the inside of the coin door that inspects the coin w determine if the correct coin has been inserted,

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop, COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing ne ry to keep the display in synchronization with the game circuitry, COMPOSITE VIDEO Complete video signal from the tem to drive the display circuitry, Cand game usually comprising H SYNC. VY the video,

CREDIT One play for one person based on the game ssvitch settings

CRT Cathode-ray tube. DATA General term for the numbers, fete: symbols that serve as input for de sing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of « fixed value.

DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube, One set of coils deflects:

gl-l

Page 60

the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS: A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine, DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for wransferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure.

EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the applicadon of high voltage. FLYBACK A step-up transformer used ina display to provide the high voltage. GATE 1, A circuit with one output that responds only when a certain combination of pulses is present at the inputs.

  • A circuit in which one signal switches another signal on and off,
  • To control the passage of a pulse or

HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. ‘HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbois 0-9 and A-F are usually used. IMPLODE To burst inward; the inward coll vacuum tube, vo Inpu/Output. ofa

gl-2 IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention, Depending on the program, the processor May Or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic fevel. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one highspeed data stream for simultaneous transmission on a single line. NME Non-maskable interrupt NML is a request for service by the microprocessor from extemal logic, The micropro: cessor cannot ignore this interrupt request. PAGE A subsection of memory. A readonly memory device (see ROM) is broken into discrete blocks of d: These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed: cuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POFENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as.a voltage divider, Also called a pot (slang), 2, An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data, 1.

cit RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and ventically with an electron beam. The display system controls the intensity of the electron beam. RETRACE Ina raster-scan display, retrace is the time the cathode-ray tube electron ting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop, ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of st equipment called signature Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into fourtdigit hex-

adecimal signatures. The signature read

by the analyzer at each cirbuit- node is then compared with the knownigood signature for that node. This progess continues until a fault is located. 4 TROUBLESHOOT * ‘The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a-cathode-ray tube. warcHDpoG = * " A counter circuit desigetea to protect the microprocessor from self-destruction if a program malfunction ‘occurs. If a malfunction does occur, the counter applies conti uous pulses td the reset line of the microprocessor, which Causes the microprocessor to keep resetting, X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A Special diode used as a regulator. Its main characteristic is breaking down at a i fied reverse-bias (Zener) voltage.

Page 61

AM

ATARI

GAMES

Road Riot 4WD Kit Statistics Sheet

Date Recorded: Location:

Meter:

Statistics Screen

Left Coins:

Right Coins: Auxiliary Coins: New Games: Continuation:

Free Games:

Idle Time:

Active Time: Solo Time:

Linked Time:

Error Count: Total Credits:

Total Coins:

Average Time/Credit: Average Time/Coin: PTET TTLA TTT

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

Teele eel eel el ella el eel ele fel el pel el pelel el fel el pel fel fel

Warranty

_ Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and (©) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Sell-

ex and Buyer which contract supersedes the terms herein, this warranty is

expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety, Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories, Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 64

ATARI GAMES COKPORATION

675 Sycamore Drive

P.O. Box 361110

Milpitas. CA 95036