CATHODE RAY TOMES

Pole Position TM-218 2nd Printing

Pole Position (World) (Namco, 1982) · Technical Manual · 88 pages · 56 sections · original scan

Page 1

Operation,

a 6) c © IS ® NS) f= © =

and Service Manual

nd Illustrated Parts Lists Complete with Schematics ai

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Facific Time) = From California, Alaska, or Hawaii + (408) 745-2900 = Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey @ (201) 469-5993 = From anywhere else in this area toll-free (800) 526-3849

EUROPE

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND BZ 06252155

Page 3

Operation, Maintenance, and Service Manual

Complete with Schematics

and Illustrated Parts Lists

*Pole Position is engineered and designed by Namco Ltd. Manufactured under license by Atari, inc.

Page 4

Pole Position

© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties. for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to ‘one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035

Lithographed in the U.S.A. 12L

Page 5

Pole Position

Notice Regarding Non-ATARI Parts

WARNING

Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: @ substitute non-ATARI parts in the game @ modify or alter any circuits in the game by using kits or parts not supplied

to licensed communications services is not permitted by the Federal Communications Commission (FCC). If you suspect interference from an ATARI® game at your location, check the following: ® all green ground wires in the game are properly connected as shown in the the game wiring diagram @ the power cord is properly plugged into a grounded 3-wire outlet @ the game PCB is properly installed within the Electromagnetic Interference (EMI) cage @ the EMI Shield PCB is properly installed and in series with the game PCB harness. Refer to Figure 3-15 to make sure that the game PCB and the Shield PCB are correctly installed. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area.

Page 6

Pole Position

Table of Contents

1 Set-Up Procedures

Inspecting the Game .. Leveling the Sit-Down Cabinet. . Space and Power Requirements

  • Installation Requirements. . .
  • Selecting the Voltage Plug Locating the Switches ...
  • Power On/Off Switch
  • Utility Panel Switches
  • Option Switches ...
  • Memory Back-Up Jumper . Setting the Option Switches .. Performing the Initial Self-Test . Game Play..........-
  • Attract Mode
  • Play Mode ....
  • High-Score Mode
  • Hints for Game Play. . poOp>

m

rom

2 Self-Test Procedure A. Comments on Troubleshooting . B. Performing the Self-Test... 0.00.0... cece cece ee ee eens

3 Maintenance, Repair, and Parts

Player Controls ..........cc scene eee Fluorescent Tube and Speaker Replacement . Video Display. ...............00e cee Utility Panel . . Coin Doors ....... Printed-Circuit Boards . Power Supply Assembly. ..........--..-000eeee rammoomp>

Glossary of Terms ..... 20.000... 0... cece ccc eee cece New Features ... 2.00... c cece eee cece eee eens

Cabinet-Mounted Assemblies-............. 000s ccc cence eee

Page 7

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4

Figure 1-5 Figure 2-1 Figure 2-2 Figure 2:3 Figure 2-4

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4

Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8

Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12

Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16

Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20 Figure 3-21

Table 1-1 Table 1-2 Table 1-3 Table 1-4

Table 2-1 Table 2-2 Table 2-3 Pole Position

List of Illustrations

Game Overview, Upright Cabinet 1-2 Game Overview, Sit-Down Cabinet . 1-3 Leveling the Sit-Down Cabinet . - 15 Location of Game Switches.............. 06 esse cece eee 16

Self-Test Display... 0.0... cece eet eet tees 4-11 Self-Test Screen 1: Upright Test Passes oe 23 Self-Test Screen 1: Sit-Down Test Passes . 2-3 Self-Test Screen 1: Test Fails ........ 23 Self-Test Screen 2 2-4

Illustrated Parts Lists

Cabinet-Mounted Assemblies, Upright Cabinet .............. 3-2 Cabinet-Mounted Assemblies, Sit-Down Cabinet . 3-4 Control Panel 37 Control Panel Assembly ........0.. 000. cece cece e eee 3-8

Steering-Wheel Control Resembly, . 310 Gear-Shifter Control Assembly. . 3-12 Foot-Pedal Control Assembly 3-14 Fluorescent Tube and Speaker Board Removal, Upright Cabinet 3-16

Fluorescent Tube and Speaker Board Assembly Upright © Cabinet 3-17 Sit-Down Cabinet Speaker Removal . . . 318 Video Display . 3-21 Utility Panel Assem 1 3-22

Vertically Mounted Coin Door .......... 06.60 cece eee 3-24 American-Made Coin Door...... 3-27 Removing the Printed-Circuit Boards ............- 3-30 Central Processing Unit Printed-Circuit Board Assembly ...... 3-32

Pole Position Video Printed-Circuit Board Assembly.......... 3-40 Regulator/Audio Il PCB Assembly, U.S.-Built Cabinet . . «. 3-45 Regulator/Audio Il PCB Assembly, Ireland-Built Cabinet -. 3-46 EMI Shield PCB Assembly . 349 Power Supply Assembly .............s.sssse. sss eeseevee B51

Switch Settings for Game and Price Options ................ 18 Switch Settings for Game and Play Options . . 19 Self-Test Procedure ............. Qualifying Lap Information

Locating Failed Components on the Video PCB 2-2 Locating Failed Components on the CPU PCB . 22 Locating the Failed RAM..............-...- 24

Page 8

Pole Position

vi

NOTICE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.

Page 9

Set-Up Procedures

How to Use this Manual

This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright

cabinet, this symbol appears: i

Whenever information is unique to the Sit-Down

cabinet, this symbol appears: r 2)

Wherever information is unique to /reland-Built games, this symbol appears: -

TAS olka (ey

a Ss Chapter 1 describes new features, game setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. A glossary of terms is in the back of this manual for your convenience. In addition, schematic diagrams of the game circuitry are included with this manual. Figures 1-1 and 3-1 illustrate the Upright game cabinet; Figures 1-2 and 3-2 illustrate the Sit-Down game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.

TAY KI VS Pa! rail ai

Page 10

Set-Up Procedures Pole Position

ATTRACTION PANEL, FLORES CENT Tee % GAME IDENTIFICATION LABEL See Figure 3-8 or 39 (Serial number appears here on Ireland-Built games)

% VIDEO DISPLAY. See Figure 3-11 ACCESS PANEL

DASHBOARD

‘STEERING-WHEEL ‘See Figure 3-1

CONTROL ASSY, See Figure 3-5 EMI CAGE See Figure 3-15 * GAME PEBE &3.20 See Figures 3-15, 3-16, & 3-17

onl GEAR-SHIFTER SY CONTROL ASSY. See Figure 3-6 UTILITY PANEL: % REGULATOR! See Figure 3-12 CAPACITOR AUDIO II PCBs See Figure 3:21 See Figures 3-15, 318, & 3-19

CONTROL PANEL Ly See Figures 33 & 3-4 SPEAKER See Figure 39

POWER SUPPLY POWER ON/OFF SWITCH See Figure 3-21 COIN DOOR See Figures 3-13 & 3-14

FoorPEDAL assy. ATU See Figure 3-7

WARNING

SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded! x Items with a serial number label on U.S.-Built cabinets

Figure 1-1 Game Overview

Upright Cabinet

1-2

Page 11

Pole Position Set-Up Procedures.

  • GAME IDENTIFICATION LABEL (Seria) number appears on exterior of rear access panel of ireland-built games)
  • GAME PCBs UTILITY PANEL ASSY. See Figures 3-15, 3-16, & 3-17 See Figure 3-12 SPEAKER’ >

oa EMI CAGE See Fi 10

See Figures 3-15 & 3-20 =—

ATTRACTION PANEL See Figure 32

ACCESS PANEL

  • REGULATOR/ AUDIO II PCBs See Figures 3-15, 3-18, & 3-19

POWER ON/OFF SWITCH

  • POWER SUPPLY CAPACITOR See Figure 321 See Figure 3-21
  • VIDEO DISPLAY See Figure 3-11

STEERING-WHEEL CONTROL ASSY. See Figure 35

GEAR SHIFTER CONTROL ASSY. See Figure 3-6

CONTROL PANEL See Figures 33 & 34

COIN DOOR See Figures 3-13 & 3-14

WARNING ACCELERATOR AND BRAKE

SHOCK HAZARD See Figure 3-7 “Sy

This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded! x /tems with a serial number label on U.S.-Built cabinets

Figure 1-2 Game Overview Sit-Down Cabinet

Page 12

‘Set-Up Procedures Pole Position

A. New Features B. Inspecting the Game

The Pole Position game has many new features. Even if you are familiar with ATARI® games, you should note these important differences: e@ Electromagnetic Interference (EMI) Cage in Please inspect your game carefully to ensure that it was delivered to you in good condition.

U.S-Built Cabinets Only. Games built after December 1, 1982, will have the CPU and Video printed-circuit boards (PCBs) mounted inside this cage. The EMI cage reduces interference from the game to television and radio receivers. See Figure 3-15 for details. @ American-Made Coin Door. Your game may be equipped with a new coin door. This door is very similar to the vertically mounted coin door, but does not have lockout coils. When ordering parts for your coin door, please check coin door illustrations in Figures 3-13 and 3-14 carefully to make sure you are ordering the correct part number. Steering-Wheel Control. This steering wheel is designed to provide a more realistic response from the race car on the display. Foot-Pedal Control (Accelerator and/or Brake). These pedals have been redesigned to accommodate a snap-action switch for the brake anda potentiometer, turned by a spring and cable, for the accelerator. @ Metal Attraction Panel on SitDown Game Cabinet. The metal attraction panel mounted on top of the cabinet entices players with its Formula-1 racing graphics. @ Quadraphonic Sound in Sit-Down Cabinet. Four 4-ohm, 6-ounce, high-fidelity speakers (two under the control panel; two behind the seat) surround the player with the exciting and realistic sounds of Gran Prix racing. New features and other major parts of the game

WARNING To avoid electrical shock, do not plug in the game until the procedures in Sections B, C, and D have been completed!

Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits are firmly plugged into their sockets on the printed-circuit boards (PCBs). c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect ihe power cord for any cuts or dents in the insulation. Repair or replace it as required, Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Note the game serial number printed on a label on the back of the cabinet. Verify that the same serial number is also on the Pole Position game PCBs, Regulator/Audio I! PCBs, power supply, and video display. See Figures 1-1 and 1-2 for locations of the serialnumbered components. Please mention the serial number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure they are mounted securely. are shown in Figures 1-1 and 1-2. Throughout this manual, wherever a new feature is mentioned, you wilt see this symbol:

A

WARNING

To avoid electrical shock, do not touch internal parts of the display with your hands or with metal objects held in your hands!

1-4

Page 13

Pole Position

  • For the Sit-Down cabinet, remove the metal attraction panel from the protective wrapping. Remove the three button-head screws and retainer on the front window. Place the attraction panel over the mounting holes. Reinstall the retainer and screws.

C. Leveling the Sit-

C. Leveling the Sit Down Cabinet

The Sit-Down cabinet rolls easily from location to location on 4-inch casters. To level the cabinet, lift the game up on one side. Place a block of wood, a book, or another object (that is at least 2-inches thick) under the raised cabinet. Partially unscrew the adjustable glides (see Figure 1-3) until they extend below the caster. Lower the game and lift it up on the other side; partially unscrew the adjustable glides. Lower the game. To prevent players from moving the game around, be sure to adjust all four glides.

CASTER \y ADJUSTABLE GLIDE

Figure 1-3 Leveling the Sit-Down Cabinet Set-Up Procedures:

D. Space and Power Requirements

  • Installation Requirements

Power 250 W Temperature 0° to + 38°C (+32° to + 100°F) Humidity Not over 95% relative Upright Cabinet 62 x 90 cm (25% x 35% in.) 186 cm (72% in.) Sit-Down Cabinet 165 x 64 cm (65 x 25% in.) 194 cm (76 in.) Space Required Game Height

Space Required Game Height

  • Selecting the Voltage Plug
WARNING SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!

The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Next, check the wire color on the voltageselecion plug that is plugged into the game’s power supply. Make sure the voltage-selection plug is correct for the voltage of your location (see Figure 3-27). Now, plug the game into a grounded 3-wire outlet.

Page 14

Set-Up Procedures

E. Locating the Switches

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls. Pole Position

  • Power On/Off Switch

The power on/off switch is located on the back of the Upright cabinet on the lower left side. On the Sit- Down cabinet the power on/off switch is located on the lower left side of the cabinet (see Figure 1-4).

OPTION SWITCHES SWITCH AT 9JA (Game and price) SWITCH AT 9L (Game and play)

information.

JUMPER AT 6B (Memory back-up) See CO-218-01 for NAMCO PCB UTILITY PANEL ASSY. See Figure 3-12

POWER ON/OFF SWITCH

Figure 1-4 Location of Game Switches

1-6

Page 15

Pole Position

  • Utility Panel Switches The volume control(s), self-test switch, coin count er(s), and auxiliary coin switch are located on the utility panel in both the Upright and Sit-Down cabinets (see Figure 3-12). The utility panel is located inside the upper coin door. The volume control(s) adjust the level of sound produced by the game. The Sit-Down cabinet has four volume controls: one for each speaker. The Upright cabinet has two volume controls: one for each speaker. The self-test switch is used to enter and exit the Self-Test Mode. The coin counter(s) record the number of coins entered into the game. The auxiliary coin switch is used to credit the game without activating the coin counter(s).
  • Option Switches Option switches are located on the game CPU PCB (see Figure 1-4). Refer to supplement CO-218-01 for switch locations if your game has NAMCO PCBs.

a. Game and price options are at CPU PCB location QUA. b. Game and play options are at CPU PCB location 9L.

  • Memory Back-Up Jumper The memory back-up jumper is at CPU PCB location 6B. Position this jumper to the on setting. The memory back-up jumper is positioned on the off setting when shipped from the factory to prevent leakage and to provide longer life for the battery at location 6A on the CPU PCB. The jumper must be Positioned to the on setting so that the battery can provide power to the CMOS memory. This memory stores the high-score table and operator statistics. Set-Up Procedures

The jumper does not affect game play. We recommend you position this jumper to the off setting when you expect extended downtime.

F. Setting the Option Switches

Settings of the game option switches are explained in Tables 1-1 and 1-2. Options preset at the factory are shown by the <4 symbols. However, you may change the settings according to your individual needs. To verify option-switch settings, first set the power on/off switch to the off position and then to the on position. Next, Set the self-test switch to the on position. Compare the information on the screen to the option switch settings fisted in the tables in this section. Then set the self-test switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism muitipliers, number of laps per game, and number of seconds per lap. These switches are on the game CPU PCB at location 9JA. The multipliers (JA switches 1-5) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. The mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1.

1-7

Page 16

‘Set-Up Procedures

NOTE
CoinOptionInterconnectAssembly

J55A-P55A permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Op-

tionInterconnectWiringDiagramin
SP-218).Whenitisused,leftcoin

mechanism option switches at 9JA apply to both coin mechanisms. If you want different options for the left and right coin mechanisms, remove Coin

OptionInterconnectAssemblyJ55A-

P55A and connect J55 directly to P55. \f you have NAMCO game PCBs, refer to CO-218-01 for the location of the option switches. Pole Position

Table 1-1 Switch Settings for Game and Price Options

Settings of 8-Toggle Switch on Pole Position CPU PCB (at 9JA)

87654321

Option

On Off

Off relis

Off On Off On

On Off On On

Off Off

On Off On On

On Off On Off On On On On Off On Off

On Off On Off On 4racing laps * 3 racing laps <

90 seconds per lap < 100 seconds per lap 110 seconds per lap 120 seconds per lap *

Right Coin Mechanism 1 coin for 1 credit < 2 coins for 1 credit * 3 coins for 2 credits 4 coins for 3 credits

Left Coin Mechanism 1 coin for 1 credit 1 coin for 2 credits 1 coin for 3 credits

2 coins for 1 credit * 3 coins for 1 credit 3 coins for 2 credits 4 coins for 3 credits Free Piay

«Manufacturer's recommended settings for Upright cabinet Manufacturer's recommended settings for Sit-Down cabinet

Page 17

Pole Position

NOTE

We recommend that game difficulty for the race laps (EXTENDED RANK) and the qualifying lap (PRACTICE RANK) be increased periodically. These changes will ensure that Pole Position continues to offer maximum excitement and challenge. Except in locations with extremely skillful and advanced players, these settings should not be increased more than one level per month. Set-Up Procedures

Table 1-2 details option-switch settings for the Attract Mode sound, kilometers or miles per hour, and difficulty in race laps and qualifying laps. The switches are on the game CPU PCB at location 9L. Pole Position leaves the factory with option switches set at the manufacturer's recommended difficulty level. The game will be exciting and challenging for players at these settings.

Table 1-2 Switch Settings for Game and Play Options

Refer to CO-218-01 for switch locations if your game is equipped with NAMCO PCBs.

Settings of 8-Toggle Switch on Pole Position CPU PCB (at 9L)

87654321

Option

Off On

Off On

FLotfoffott
Wf OffOffOn
€ OffOnOff
iy Off= OnOn
“OnOffOff
5 OnOffOn,

On

: OnOnOn-—™

Attract Mode sound off Attract Mode sound on <4

Kilometers per hour Miles per hour <

Difficulty in Race Laps Easiest lap <

Most difficult lap

Difficulty in Qualifying Lap Easiest lap 7

~<

Most difficult lap

“<Manufacturer's recommended settings

Page 18

Set-Up Procedures

G. Performing the Initial Self-Test

This game will test itself and provide data to show that the game's circuitry and controls are operating properly. The data is provided on the video display and speakers. No additional equipment is necessary. Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score gable or distort the statistics. All credits will be cancelled when you switch to self-test.

Refer to Figure 1-4 for the location of the option switches and Figure 3-12 for the location of the selftest switch. Set the self-test switch to the on position to see the Self-Test Display in the Self-Test Mode (see Figure 1-5). To exit the Self-Test Mode, set the self-test switch to the off position. Pole Position

The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. \f a part of the test described in Table 1-3 fails, refer to Chapter 2. We suggest you perform the self-test procedure when you first set up the game, when you collect money from the game, when you change game options, or when you suspect game failure.

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.

Table 1-3 Self-Test Procedure

Instruction Test Passes

  • Without touching the pedal(s), set the self-test switch to the on position. All credits will be cancelled.

.. Press down on the accelerator pedal.

. Press down on the brake pedal of the Sit-Down cabinet.

. Turn the steering wheel clockwise, then counterclockwise.

. Shift the gear shifter.

. Shift the gear shift, press the auxiliary coin switch, and activate the coin switches.

. Press the auxiliary coin switch.

. To end the test, switch the self-test switch to off. Random symbols are displayed on the screen for about five seconds. The self-test display appears. RAMs and ROMs are tested. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self-Test Procedure.

The numbers to the right of ACCEL increase from 00 to somewhere between 90 and AQ as you press down on the pedal. If the test fails refer to Chapter 2. . The numbers to the right of BRAKE switch from 00 to FF. For the Upright cabinet, the numbers to the right of BRAKE should always read 00. If the test fails, refer to Chapter 2.

Rotating the whee! clockwise causes the numbers to the right of STEER- ING to increase. Rotating the wheel counterclockwise causes the numbers to decrease. If the test fails refer to Chapter 2.

The words to the right of SH/F T change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, refer to Chapter 2.

The numbers to the right of SOUND increase from 00 to 20, and a new sound is played with each number. Test all 20 sounds. If the test fails, refer to Chapter 2.

Game statistics appear (for a few seconds) at the bottom of the screen. Press the coin switch each time you want to see the statistics. To erase game statistics, simultaneously press down on the accelerator pedal and press the auxiliary coin switch twice. Statistics will be reset at /999/. To reset the high-score table, simultaneously press down on the accelerator pedal and change gear shifter from low to high. The high-score table will be reset and contain fictitious scores.

Page 19

Pole Position Set-Up Procedures

ALL RAMS GOOD

ACCELERATOR PEDAL te <

CC ALL ROMS GOOD

STEERING oe —_ =| bien STEER T Lo — FAR SHIFTER

: : es MECHANISM a | ACREDIT ab RIGHT COIN CREDIT-~—_—— MECHANISM

QUALIFYING :

—_—--——— 7

LAP TIME TIM NO. OF LAPS

iN THE RACE

(See Table 1-2) QUALIFYING LAP DIFFICULTY LEVEL (See Table 1-2) RACE DIFFICULTY LEVEL— > EXTEND

e———— GAME STATISTICS

GAME AUTOMATICALLY STARTS* (When correct number of coins are inserted) THE COUNT STARTS AT 999(999) AND DECREASES. For example, if you play 10 games, the game subtracts 10 from 999, and the display shows 98.9 for the number of games played. (Disregard decimal points.)

NO. OF GAMES PLAYED NO. OF POINTS SCORED (x10) NO. OF SECONDS PLAYED NOT APPLICABLE

999. 999, 999. 999, 999,

NO, OF SECONDS THAT GAME

HAS BEEN POWERED ON NO. OF GAMES IN WHICH PLAYER HAS QUALIFIED NO. OF GAMES IN WHICH PLAYER REACHED FINISH LINE

NO. OF GAMES THAT REACHED NO. OF GAMES THAT REACHED THIRD EXTENDED LAP “If screen displays MANUAL START, FIRST, EXTENDED TAP suspect the game harness. NO. OF GAMES THAT REACHED Refer to the Schematic Package. SECOND EXTENDED LAP

Figure 1-5 Self-Test Display

1A

Page 20

Set-Up Procedures

H. Game Play

Pole Position is a one-player game using a color raster-scan video display. The game action takes place at Fuji Speedway in Japan. The country around the speedway consists of green meadows, hills, and snow-capped Mt. Fuji. The player drives a Formula-1 race car on the Fuji Speedway. Player controls consist of a steering wheel, a two-position gear shifter, and accelerator and brake pedals on the Sit-Down cabinet (accelerator only on the Upright cabinet). The object of the game is to finish the qualifying lap as quickly as possible. If the player beats the clock, he qualifies for the Gran Prix at Fuji Speedway; if not, he drives out the remainder of his time along the qualifying course. As a qualifier, the driver is ranked according to his qualifying lap time, from position one (the pole position) to position eight. The player then races against the clock and other cars to finish the four laps (operator-selectable option) of the race as fast as possible and to achieve the highest score possible. The player earns points for passing cars, driving on the track, and finishing the race with time remaining. He is rewarded with an extended-play lap for completing a lap. Pole Position has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game switches and computer functions. You may enter the Self-Test Mode from any other mode. However, all credits will be cancelled. Pole Position

  • Attract Mode

The Attract Mode begins when you set the power on/off switch to on or after the Play, High-Score, or Self-Test Modes. The Attract Mode ends when the correct amount of credit for a game is inserted or when the Self-Test Mode begins. When the Attract Mode begins, the game displays a picture with the words POLE POSITION flashing at the top of the screen. A map of Fuji Speedway is displayed in the center of the screen. Within the map are the words FUJ/ SPEEDWAY and 7 LAP 3459M. At the bottom of the screen is the copyright message. Then, the Attract Mode simulates game play. Eight cars are at the starting line. The player’s car, located in the eighth position, flashes on the screen. The starting lights flash from red to green and the race starts. The race continues until the player's car crashes into another car and explodes into a red ball of fire. Then, the car reappears on the screen and continues down the track until it hits a sign along the side of the road. Again, the car explodes. During this sequence, the message GAME OVER appears in the center of the screen. Finally, the Attract Mode displays the High-Score Table. The fastest lap time, average game speed, and prize winners appear at the top of the screen. Below this information is a list of the six highest scores. Opposite each score are the initials of the player who achieved that score.

  • Play Mode The Play Mode begins when the correct amount of credit for a game is recorded. The game starts with the player's car behind the starting line and 90 seconds on the clock. (See Section E to select a different clock setting.) The car must finish the qualifying lap within 73 seconds to be in the race. If the player does not qualify, his car continues on the track until 90 seconds are used up.
Page 21

Poie Position

Table 1-4 Qualifying Lap Information

POSITION = QUALIFYING LAP TIME* BONUS POINTS 58” 50 60” 00 62” 00 64" 00 66" 00 68” 00 70” 00 73" 00 88888588

“In seconds and hundreaths of a second

Just before the race begins, the player's car (flashing on the screen) is placed at the starting line with seven other cars. The position of the car depends on the qualifying time as shown in Table 1-4. The starting lights flash from red to green, and the race begins. Racing hazards are other racing cars, sharp turns, and road signs. As the race progresses, more cars appear on the track. If the driver's car hits another car or a road sign, the driver's car is destroyed in an explosion. The driver's car reappears in a few seconds and the race continues. Driving through wet puddles or off the track slows down the driver's car. Racing into the first turn, the driver must let up on the accelerator slightly to make the corner. Road signs flash along the side of the track. Depending on how well the player manipulates the controls, he can either roar through the hairpin turns like a champion or spin out in a flaming crash. He jockeys for position with the other racers, while keeping his eye on the clock at the top of the screen. When his time runs out, the race is over. The top score achieved by a player appears at the top of the screen. The time alloted for the lap is displayed under the top score. Increasing lap time (in seconds and hundredths of a second) and the speed of the car appears last. Set-Up Procedures

  • High-Score Mode The High-Score Mode begins when a player has earned one of the 300 highest scores. The player has one minute to record his initials. A player rotates the steering wheel to locate his initial. He presses a foot pedal to put his initial on the screen. The third time he presses the pedal his initials are transferred into the high-score table.
  • Hints for Game Play ¢ Avoid puddles and the sides of the track because these slow you down. ¢ Accelerate and stay ahead of other racers.
  • Stick to the inside of the track to make the corners. ° Successful completion of a turn depends on braking skill.
  • When sliding, steer into the skid.

O

1-13

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

Self-Test Procedure

NOTE

The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco Q PCBs, please refer to CO-218-01.

The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. If there is a failure, the game Produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is working properly. SURF

eee ae on eae wer Cd A

Chapter

Page 24

Self-Test Procedure

A. Comments on Troubleshooting

When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting a PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Tables 2-1 and 2-2 are troubleshooting aids, which can be used to locate faulty components.

Table 2-1 Locating Failed Components Pole Position

Table 2-2. Locating Failed Components on the CPU PCB

Custom AtoD

Symptom Area PROM IC RAM Converter

Audio Voice 9c 9D Screech/Crash 9E Player's Motor 12E,12F All Other Sounds 7LAID 7K,75 Inputs Brake and/or Accelerator a Steering 9K Option Switches 9K,9M All Other Inputs 9M Control for Audio & Inputs 8H,9H Syne 7M High Scores 7E

on the Video PCB

‘Symptom Area PROM Custom RAM Ic Large Car Pictures 12,130 Large Sign Pictures 12K,13K,12L, 13L Small Cars & Signs 12N,13N All Cars & Signs 12H,11N 13H ‘9F,10F Alphanumerics 7N,8M 8N Raceway 2L,2M,2N,4L 3N Background 6N,5K Raceway & Background 5L,6L Middle & Sides of Raceway 2B,2C,2D All Video 4D,7E,2F Red 11E Green nD Blue 1c

B. Performing the Self-Test

This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. Video game repair should only be performed by a qualified electronic technician. To begin the Self-Test Mode, set the self-test switch, which is located on the utility panel, to the on position.

CAUTION

Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.

Page 25

Self-Test Procedure Pole Position

SELF-TEST SCREEN 1—Test Passes: SELF-TEST SCREEN 1—Test Fails:

Upright Cabinet. If the test passes, the screen If the test fails, the screen may display the picture displays the picture in Figure 2-1, Upright Test in Figure 2-3, Test Fails. Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.

Figure 2:3 Self-Test Screen 1: Test Fails

ROM failure is indicated by the word ROM anda Figure 2-1 Self-Test Screen 1: a pair of alphanumeric characters displayed at the top Upright Test Passes Of the screen,

Sit-Down Cabinet. If the test passes, the screen displays the picture in Figure 2-2, Sit-Down Test Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.

ACCEL 90 STEERING. SOUND COIN: | COIN2 TIME 3 GOAL EXTENDED PRACTICE RANK C AUTO START

Figure 2-2 Self-Test Screen 1: Sit-Down Test Passes

Page 26

Self-Test Procedure

RAM failure is indicated by the word RAM anda pair of alphanumeric characters displayed at the top of the screen. Table 2-3 lists the failed RAM chip, the printed-circuit board (PCB) the chip is on, and the chip’s location. Replace the failed RAM, and restart the test (set the self-test switch to off, and then to on).

NOTE
Thereferencedesignatorsforcom-

ponents in this chapter refer to games with Atari® PCBs. If you have Namco PCBs, please refer to CO-218-01.

Table 2-3 Locating the Failed RAM

Falled PCB Screen Display RAM Location

VideoRAM 08F
VideoRAM 17F
Video:RAM 28H
VideoRAM 37H

CPU RAM 6 TW

CPU RAM7 7K

CPU RAM 8 7E

VideoRAM 22Bu
VideoRAM 237
VideoRAM 268K
VideoRAM 277K
VideoRAM 283F
VideoRAM 294F
VideoRAM 303E
VideoRAM 314E

Steering failure is indicated by failure of the numbers to the right of STEERING to properly increase or decrease. As you rotate the wheel clockwise, these numbers should increase; as you rotate the wheel counterclockwise, they should decrease. If the test fails, suspect the Coupler PCB.

Accelerator failure is indicated by failure of the numbers to the right of ACCEL to increase as you press down on the pedal. If no numbers appear, suspect a bad A-D converter on the CPU PCB ora mechanical problem on the foot pedal assembly. Troubleshoot using the information in Chapter 3, Section B, and the game schematics. Pole Position

Brake failure on the Sit-Down cabinet is indicated by failure of the numbers to the right of BRAKE to change as you press down on the brake pedal. On the Upright cabinet, brake failure is indicated by anything other than 00 appearing to the right of BRAKE. If the test fails, suspect a bad switch, improper mechanical adjustment on the foot pedal assembly, or no ground on the brake edge-connector pin in the harness. Gear-shifter failure is indicated by failure of the words to the right of SHIFT to change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, suspect loose connector wires or a bad switch. Sound failure is indicated by the absence of any sound when the coin switches or gear shifterare activated. Suspect a loose harness or connector wire, the volume control turned off, the custom audio I/O chip, or the Regulator/Audio Hi board. Troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off and immediately back to on,

SELF-TEST SCREEN 2: A white crosshatch pattern appears on the screen (see Figure 2-4). Use this pattern for convergence (see the raster-scan video display manual).

Figure 2-4 Self-Test Screen 2

Page 27

Maintenance, Repair, and Parts

This chapter details maintenance and repair information and provides information you need to order parts for your game. Common hardware (screws, nuts, washers, bolts, etc.) has been deleted from most of the parts lists. However, a parts list for the hardware to mount the printed circuit boards (PCBs) to the cabinet has been included. The printed circuit board (PCB) parts lists are arranged in alphabetical order by component. Each component subsection is sorted by reference designator Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598-through approximately 201000-. \ When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter

Page 28

Maintenance, Repair, and Parts Pole Position

A. Cabinet-Mounted Assemblies Manuals, Schematics, & Self-Test Label— See parts list on next page

Fluorescent Tube and Speaker See Figures 3-8 & 3-9 037332-01 (Ventilation grille)

039371-01 (Shield retainer)

039417-01 (Display shield)

Video Display See Figure 3-11 (Access panel} A037701-01 (EMI Cage) See Figures 3-15 & 3-20 Game PCB Assy. A039420-01 See Figures 3-15, (Dashboard/decal) | 1 3-16, & 3-17 ‘Steering-Wheel Control Assy. v .Gear-Shifter Control Assy. A039459-01

See Figure 3-5=ZSee Figure 36(Main har. assy)

A039499-01

178034-024Control Panel Assy.™
(Molding)See Figures 3-3 & 3-4(Main ham/-essy)

148001-001 : Regulator/Audio I!

Utility Panel(Speaker)lfPCB Assy.
See Figure 3-12039144-01$\See Figures

a (Speaker grille) ras 1 3-18 & 3-19 Coin Door Assy. Q See Figures A039460-01 313 & 3-14 (Power harn. assy.) 038870-01 = Power Supply (Coin box enclosure—& i ‘A037453-04

= not ‘ShownSee Figure 3-21(Power cord)

038091-01 A037454-04 (Coin box—not shown) b 178048-001 (Caster)

‘A039353-01 (Power cord)

1—(Cabinet assy.)‘A037470-01

i Le iding) A039353-02 (On/off switch assy.) (Cabinet assy.) 009992-01 78-3201 Foot-Pedal Assy. (On/off switch cover) (Glide) See Figure 3-7

Figure 3-1 Cabinet-Mounted Assemblies

U.S.-Built Upright CabinetA039352-01B

lreland-Built Upright Cabinet A039352:02 B

3-2

Page 29

Pole Position Maintenance, Repair, and Parts

Cabinet-Mounted Assemblies Upright Cabinet Parts List

Assemblies and components in the following parts list are shown in Figure 3-1.

Part No. Description For U.S-Built Upright Cabinet A037453-04 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference Cage (includes guides) A039353-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039459-01 Main Harness Assembly (for U.S. PCB) For ireland-Built Upright Cabinet A037454-04 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039353-02 Cabinet Assembly (inciudes glides and PCB retainers, but not the rear access panel) A039499-01 Main Harness Assembly (for NAMCO PCB) For U.S.-Built and Ireland-Built Cabinets A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039420-01 Dashboard Housing and Decal Assembly A039460-01 Power Harness Assembly A039576-01 Coin Option Interconnect Assembly

The following nine items are technical information supplements to this game: CO-218-01 Pole Position Supplement (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari? game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings for Atari® PCBs) or ST-219-01 Pole Position Labei with Self-Test Procedure and Option Switch Settings (for NAMCO PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with pari no. 92-055) ™M-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x %-Inch Thick (48 inches required; used on top edge of video display shield, and on top edge of control panel) 78-6900404 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x %-Inch Thick (48 inches required; used on top and bottom of attraction panel) 009992-01 On/Off Switch Cover 037332-01 Ventilation Grille 038091-01 Molded Coin Box (not shown) 038770-01 Metal Coin Box Enclosure (not shown) Acceptable substitute is part no. 038781-01 039144-01 Speaker Grille 039371-01 Video Display Shield Retainer 039376-01 Rear Access Panel (does not include lock) 039417-01 Video Display Shield with Graphics 148001-001 6- x 9-Inch Ovai, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (located on front panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no, 171027-001. 178034-024 34-Inch Black Plastic T-Molding (located on side panels) 178034-025 25,-Inch Black Plastic Molding (/ocated on front panel) 178048-001 2-Inch Rigid Caster

Page 30

Maintenance, Repair, and Parts Pole Position

A039465-01 A039101-01 (Main harn. assy.) (Cabinet assy.) A039245-01 A039101-02 (Main harn. assy.) (Cabinet assy.) Game PCB Assy. See Figures 3-15, 3-16, & 3-17

037990-01 (Vent. Grille)

148001013 (Speaker) 178034-034 canst (T-Molding) Agron ot (Speaker grille) y™) cage) See Figures 039144-01 3-15 & 3:20 (Grille) 03864101 148001-001 (Vent. grille) (Speaker)

‘A038881-01- (Lock) 178034-024 (T-Molding)

Utility Panel See Figure 3-12

Regulator/Audio Il PCB Assy. ¢ See Figures 3-18 & 3-19 ( AA Gi Power Supply Assy. NS 035851-01 See Figure 3-21 wines) 8039246-01 (Power harn. assy.) A037470-01 A037453-03 (On/off switch assy.) (Power cord) 00999201 A037454-03 (On/off switch cover) (Power cord)

Figure 3-2 Cabinet-Mounted Assemblies U.S.-Built Sit-Down Cabinet A039100-01 A lreland-Built Sit-Down Cabinet A039100-02 A

3-4

Page 31

Pole Position Maintenance, Repair, and Parts

Manuals, Schematics, & Self-Test Label— See parts list on next page

Gear-Shifter Control Assy. See Figure 36

Re Video Display See Figure 3-11 037086-01 aaa rine ea Assy. (Front window retainer)

039141-01 (Front window)

(Tape)

Control Panel Assy. 039148-01 See Figures 3-3 & 3-4 (Display shield/graphics)

a

Coin Door Assy. See Figure 3-13 & 3-14

038870-01 (Coin box exclosure) Foot-Pedal Assy. See Figure 3-7

(Caster) & + 783201 (Glide)

Figure 3-2 Cabinet-Mounted Assemblies, continued U.S.-Built Sit-Down Cabinet A039100-01 A Ireland-Built Sit-Down Cabinet A039100-02 A

Page 32

Maintenance, Repair, and Parts Pole Position

Cabinet-Mounted Assemblies Sit-Down Cabinet Parts List Assemblies and components in the following parts list are shown in Figure 3-2.

Part No. Description For U.S-Built Cabinet A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) 03910101 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039465-01 Main Harness Assembly For Ireland-Built Cabinet A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039101-02 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039245-01 Main Harness Assembly (for NAMCO PCBs) For U.S-Built and Ireland-Built Cabinets A039246-01 Power Harness Assembly A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 The following nine items are technical information supplements to this game: CO-218-01 Pole Position Supplement (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari? game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari® PCBs) or ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Setting (for NAMCO PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM:201 Service Manual for 19-Inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 4-Inch Wide x %inch Thick (48 inches required; used on control panel) 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, ¥2-Inch Wide x %-Inch Thick (48 inches required; used in top slot of video display cleat, and on top and bottom of front window) 002728-01 Control-Panel Mounting Bracket 009992-01 On/Off Switch Cover 035851-01 Top Panel Hinge 037086-01 Front Window Retainer 037990-01 Ventilation Grill (on rear access panel) 038091-01 Molded Coin Box (not shown) 038641-01 Ventilation Grille (on rear access panel) 038870-01 Metai Coin Box Enclosure Acceptable substitute is part no. 038781-01 03914101 Front Window 039144-01 Speaker Grille (located behind seat) 039145-01 Speaker Grille (located under contro/ panel) 039148-01 Video Display Shield with Graphics 039155-01 Metal Attraction Panel with Graphics 148001-001 6 x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (not shown—located behind seat) 148001-013 6- x 9:Inch Oval, 4-Ohm, 15 W Shielded High-Fidelity Speaker (located under contro! panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001 176015-110 #10 x %-Inch Cross-Recessed, Pan-Head Tapping Screw (not shown—for mounting speakers/grilles to seat back) 178034-024 %-Inch Black Plastic T-Molding 178034-034 1-Inch Black Plastic T-Molding (located on seat back) 178023-001 4Inch Rigid Caster

Page 33

Pole Position

B. Player Controls

WARNING Before you remove or repair any control on the control panel, turn the game off.
CAUTION Before removing the final wing nut on the Sit- Down cabinet, hold the gear-shifter housing with one hand to prevent the front-heavy control panel from falling forward.

Control Panel Maintenance, Repair, and Parts

Opening the Control Panel:

1. Unlock and open the rear access panel (see Figure 3:3), Reach through the opening to the top of the control panel. Remove the four wing nuts and washers that secure the control panel to the Upright cabinet. Two wing nuts and washers secure the control panel to the Sit- Down cabinet.

Guide or pull the control panel forward to its resting position. The steering wheel and gear shifter are now accessible for maintenance or repair (see Figure 3-4). Make sure the foam tape is in good condition. This tape is on the control panel of the Upright cabinet, and on the display shield for the Sit-Down cabinet. Reassemble in reverse order.

Figure 3-3 Control Panel

Page 34

Maintenance, Repair, and Parts Pole Position

72-JB3814S, Screw) Players may receive an electrical shock if this ? control panel is not properly grounded! After ’ servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal tab on the inside of the control panel. ~~ 475002.004 | (Washer) J

A000608-09 Gear-Shifter Control Assy. See Figure 3-6

039154-01 (Spacer)

i samme (Control panel/decal) 039373-01 (Control panel) 75-0358 039409-04 FD (Washer) (Decal) A039108-01 (Control panel/decal) 03914301 (Control panel) 039153-04 (Decal) 039132-01

(Bezel) J 75-5512B (Carriage bolt) NN 7555243 (Carriage bolt) \ ‘A039229-01 Steering-Wheel Control Assy. Assemblies A039107-01 and See Figure 3-5 A039412-01 are used with Atar game PCBs; Assembiles A039107-02 and A03941202 are used with Namco game PCBs. Figure 3-4 Control Panel Assembly Upright Cabinet A039412-01 & -02 A Sit-Down Cabinet A039107-01 &-02 B

Page 35

Pole Position Maintenance, Repair, and Parts

Control Panel Assembly Parts List

Assemblies and components in the following parts list are shown in Figure 3-4.

Part No. Description Upright Cabinet A039411-01 Control Panel with Decal (consists of contro! panel 039373-01 and decal 039409-04) 75-5512B #%-20 x .75-Inch Black Carriage Bolt 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 4-Inch Wide x y-Inch Thick (96 inches required) Sit-Down Cabinet A039108-01 Control Panel with Decal (consists of control panel 039143-01 and decal 039153-04) 75-0358 %4-Inch Wide Flat Washer 039132-01 Control Panel Spacer

Upright and Sit-Down Cabinets A039229-01 Steering-Wheel Contro! Assembly (Namco games use part no. A039229-02) A000608-09 Gear-Shifter Control Assembly 72-JB3814S #8-16 x .87-Inch Screw 75-5524B #¥%s-20 x 1.50-Inch Carriage Bolt 75-945S #1%-20 Hex Locknut 005255-04 Shifter Bezel 039154-01 Shifter Spacer 175002-004 #10 Flat Washer

3-9

Page 36

Maintenance, Repair, and Parts

039243-01 a (Label) : Pole Position

178099-003 (Steering wheel)

039230-01 (Steering cap)

—/ —S ° 72-8012 ~ @r,r (Screw) i °| 039231.01 (Shaft)

178012-002 03923401 Cietgining ee) (Steering frame)

72-HB3606S, (Hex screw) ea, o

: 178100-001 ‘A035220-02 : (Coupler PCB assy.) << (Flange bearing) 178097-001 4 (Bearing) 175002-001 > (Washer) 175003-002 (Nylon washer) 178012-001 039233-01 >» fl (Retaining ring) (Encoder shaft) +>} at ( 178101-002 ; rra101.001 (Gear) (Gear)

175002-002 ‘(Heavy washer) 039232.01 (Spacer) 75-040 (Washer) 03593801 (Encoding wheel) 72-8008 (Screw)

(Split-ock washer) 72-8408 [ mo See text for lubrication information.

Figure 3-5 Steering-Wheel Control Assembly A039229:01 D

3-10

Page 37

Pole Position Maintenance, Repair, and Parts

WARNING wrench. Use an Allen wrench to remove the cap screw, ; encoding wheel, washers, spacer, and bearing. To Before you remove or repair any player control, remove the encoder shaft, pry off the retaining ring. turn the game off.
  • To remove the steering wheel, hold the steering wheel shaft in a fixed position. Remove the cap screw, Removing the Coupler PCB, Encoding Wheel, washers, and gear. Pry off the retaining ring and and Steering Wheel: remove the heavy washer.
  • Reassemble in reverse order.
  • Open the control panel (see Figure 3-3), To remove the steering-wheel control assembly, i, ij I. disconnect the green grand wire from the grounding Lubricating the Steering-Wheel Control: hardware. Remove the hardware which secures the The two gears and the encoder shaft of the steeringsteering-wheei control assembly to the control panel wheel control assembly (see Figure 3-5) should be (see Figure 3-4). lubricated every six months. The bronze bearings of the
3.Unplug the harness connector on the Coupler PCB.steering shaft shor be lubricated - err lubricate

ul ies, first open the contro!

4.To remove the Coupler PCB, remove the hardwareFigure 32). Apply a light tli, of Nyogel 779 Cone (see

securing the PCB to the steering frame. gears, encoder shaft, and both sides of both nylon wash-

5.To remove the encoding-wheel assembly, hold theers. If necessary, apply a light-duty oil, such as 3-in-One oil,

shaft of the encoding wheel in a fixed position with a to the bronze bearings.

Steering-Wheel Control Assembly Parts List

Assemblies and components listed in the following parts list are shown in Figure 3-5.

Part No. Description A035220-02 Coupler Printed-Circuit Board Assembly (includes Radial Optical Coupler) 72-8008 #10-32 x 0.50-Inch Steel Socket-Head Cap Screw 72-8012 #10-32 x 0.75-Inch Steel Socket-Head Cap Screw 72-8408 #4-40 x 0.50-Inch Steel Socket-Head Cap Screw 72-HB3606S #6-32 x 0.38-Inch Zinc-Plated Steel Hex Washer-Head Screw 75-040 #10 Split-Lock Washer 75-044 #4 Split-Lock Washer 75-07014 #4 Flat Washer 79-58356 4-Position Connector with Locking Ramp (located on the Coupler PCB Assembly) 030369-01 Radial Optical Coupler (located on the Coupler PCB Assembly) 035221-01 100 2, +5%, %W Resistor located on the Coupler PCB Assembly) 039230-01 Steering Cap 039231-01 Steering Shaft 039232-01 Spacer 039233-01 Encoder Shaft 039234-01 Steering Frame 039243-01 Steering Cap Label 035938-01 Encoding Wheel 107013-001 3-in-One® Oil 175002-001 Flat Washer 175002-002 #10 Heavy Flat Washer 175003-002 Nylon Flat Washer 178012-001 Retaining Ring for 0.75-Inch Shaft 178012-002 Retaining Ring for 0.25-Inch Shaft 178027-001 Nyogel 779 Lubricant 178097-001 Bearing for 0.25-Inch Shaft 178099-003 Steering Wheel 178100-001 Bearing Flange for 0.75-Inch Shaft 178101-001 24 Diametral Pitch x 20° Pressure Angle x 2.500 Pitch Diameter Spur Gear 178101-002 24 Diametral Pitch x 20° Pressure Angle x 0.583 Pitch Diameter Spur Gear

3-11

Page 38

Maintenance, Repair, and Parts. Pole Position

005255-04 OD (Bezel) NX

NOTE The shift beze! is not part of the gear shifter assembly and must be purchased separately.

ye ‘See text for lubrication information,

000610-02 (Shifter handle) <<

78-3002003 (Spring)

76-11375S (Ball bearing) 1 r 000609-02 (Shift housing)

72-14128 (Screw) 65-0218 (Switch) (Shift detent)

75-944S

  • (Hex nut) 035301-01 (Actuator pin)

Figure 3-6 Gear-Shifter Control Assembly A000608-09 Y

3-12

Page 39

Pole Position

WARNING

Before you remove or repair any player control, turn the game off.

Removing the Gear-Shifter Control Assembly: 1. Open the control panel (see Figure 3-3). Maintenance, Repair, and Parts

  • To remove the switch, remove the two screws and locknuts that secure the switch to the housing. Be careful not to lose the small actuator pin that sits above the switch actuator.
  • Reassemble in reverse order.

Lubricating the Gear-Shifter Control:

  • To remove the gear-shifter control assembly (see Figure 3-4), disconnect the plug-in connectors from I i i fo lubricate the gear-shifter contro! assembly, open the the ae Remove the hardware that secures the control panel (see Figure 3-3) and remove the gear-shifter gear-shifter control assembly to the control panel. control assembly using the procedure above. Apply a light-
  • To open the gear-shifter assembly, remove the six duty lubricant (such as Nyogel 779) every six months to the screws that secure the two halves of the housing (see spherical part of the handle and the detent. Figure 3-6).

Gear-Shifter Control Assembly Parts List

Assemblies and components listed in the following parts list are shown in Figure 3-6.

Part No. Description 0006 10-02 Gear-Shifter Handie 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 72-JB3606 #6 x 0.38-Inch Steel Plastite Screw 72-14128 #4-40 x 0.75-Inch Cross-Recessed Pan-Head Steel Machine Screw

76-11375S, %Inch Bali Bearing 75-9445 #4-40 Seif-Locking Polymer Hex Nut 78-3002003 Spring 000609-02 Gear-Shifter Housing (two required) 005255-04 Shifter Bezel 035792-01 Shift Detent 035301-01 Actuator Pin 178027-001 Nyogel 779 Lubricant (not shownj

3413

Page 40

Maintenance, Repair, and Parts Pole Position

On 03924101 \ (Safety tread)

039240-01 039236-01 (Foot pedal—accelerator)

000592-01

039242.01 (Retaining ring) (Cable)

(Pulley)

178026-006. x 72-8606 (Extension spring) 4 (Cap screw) Cap screw of pulley must be in this position when pedal is fully open (at rest). 178026-005 (Cable spring) ° 039239-01

(Base plate)

72-HB3410S* 49.9026 (Screw) (Potentiometer) : a [- 160023-001* (Switch)

| *For Sit-Down cabinet (dual foot-pedal assembly)

**For Upright cabinet (single foot-pedal assembly)

= SS 039142-01" > oe Mounting plate) SNe 75-9418 (Mounting plate) (Hex locknut) y

See text for lubrication information. (s (Washer)

Figure 3-7 Foot-Pedal Control Assembly

3-14

Page 41

Pole Position Maintenance, Repair, and Parts

WARNING Before you remove or repair any player control, 3. From the front of the Upright cabinet or in the player turn the game off. area of the Sit-Down cabinet, remove the foot-pedal mounting screws and lift out the foot-pedal control assembly.
  • The only maintenance required on this newly de- Removing the Foot-Pedal Control Assembly: signed foot-pedal control is lubrication every four months (see Figure 3-7). Lubricate the pivot pin and
1.Unlock and open the rear access panel. Reach throughsurrounding area, the springs, cable, and pulley with

the opening to the top of the foot-pedal control. dry teflon spray. If needed, apply a light-duty lubricant

2.Remove the two locknuts located on the top two foot-like WD-40 to the potentiometer shaft only.

pedal mounting screws. 5. Reassemble in reverse order.

Foot-Pedal Control Assembly Upright A039413-01 B Sit-Down A039109-01 C Parts List

Assemblies and components in the following parts list are shown in Figure 3-7.

Part No. Description Sit Down Cabinet A039247-01 Dual Foot-Pedal Control Harness Assembly 72-HB3410S #4-40 x .62-Inch Thread-Forming Hex Washer-Head Screw 75-010S #10 Tooth Internal Lock Washer 160023-001 SPDT Snap Switch with Actuator Upright Cabinet A039463-01 Single Foot-Pedal Control Pedal Harness Assembly 75-035S, Ya-Inch Flat Washer 75-040S #10 Tooth Internal Lock Washer 75-5520B #%-20 x 1.25-Inch Black Carriage Bolt (not shown) 75-9158 #%-20 Hex Nut 039379-01 Single Foot-Pedal Control Mounting Plate Upright and Sit-Down Cabinets 19-9026 5 kQ Potentiometer 72-8606 #6-32 x .38-Inch Hex Socket-Head Cap Screw 75-941S #10-24 Hex Locknut

000592-01Compression Spring(for pedal)

039236-01 Pivot Pin 039238-01 Pulley 039239-01 Foot-Pedal Control Base Plate 039240-01 Foot Pedal 039241-01 Safety Tread 039242-01 Cable 107012-001 Dry Teflon Spray Lubricant (not shown) 178012-004 External Retaining Ring for %-Inch Diameter Shaft

178026-005Extension Spring(for cable)
178026-006Extension Spring(for pedal)

3-15

Page 42

Maintenance, Repair, and Parts

C. Fluorescent Tube and Speaker Replacement

WARNING Before you remove or repair the fluorescent tube or speaker, turn the game off. If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly six feet or more from the implosion. Use care when replacing any fluorescent tube.

Upright Cabinet

Removing the Tube and Speaker Board:

  • From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker's 5-pin harness connector (see Figure 3-8). 2, From the front of the game, remove the three buttonhead screws and lock washers that secure the upper attraction-panel retainer to the cabinet. Loosen the screws and washers that secure the lower attractionpanel retainer to the cabinet.
  • Remove the attraction glass. 4, Remove the lower retainer.

(Attraction glass) graphics)

(Speaker) (Speaker grille) é Pole Position

  • Remove the two wood screws that secure the tube and speaker board to the cabinet. Slide this board out of the cabinet. After making necessary repairs or replacements, make sure that the tube and speaker board is pushed all the way back on the tube and speaker panel when you reinstall the board.

Replacing the Fluorescent Tube:

  • Check that the green ground wire is securely attached to the large metal bracket and the ballast transformer on the wood panel. If the tube is not grounded, it may not start.
  • Remove the cardboard locking tab at each end of the tube (see Figure 3-9). Slightly rotate the tube up or down and carefully remove it from the tube holder.
  • Replace it with a new tube. Do not snap in the tube vigorously— you may break it, causing an implosion! Replace the locking tabs.

Replacing the Upper Speaker:

  • Disconnect the two plug-in connectors on the speaker.
Note that the white wire (+) connects on the side marked with a painted dot.
  • Remove the screws that attach the speaker to the board (see Figure 3-9). Replace with anew speaker and reinstall the tube and speaker board.

Replacing the Lower Speaker: From the back of the game, unlock and open the rear access panel. Refer to upper speaker removal procedure in Figure 3-9.

003053-01 (Retainer)

Figure 3-8 Fluorescent Tube and Speaker Board Removal

3-16

Page 43

Pole Position Maintenance, Repair, and Parts

148001-013 70-304 99-11006 Speaker) (Tube) (Tab)

179035-001 {x (Tube holder) | | S A037457-01 @reie —f (Harness)

142028-001 (Transformer) 142028.002 (Transtormer)

99-11003 — (Starter) = 99-11009 037469-01 (Socket) (Bracket)

NOTE To make sure that the fluorescent tube starts, check that the ground wire is firmly attached to both the ballast transformer and the steel tube bracket. 79-561816P_ (Wire nut) ——! ‘A037540-01 (Board)
  • {Ground wire)

Figure 3-9 Fluorescent Tube and Speaker Board Assembly U.S.-Built Upright Cabinet A039415-01 A Ireland-Built Upright Cabinet A039415-02 A Parts List

Part No. Description For U.S-Built Upright Cabinet 142028-001 60 Hz, 118 V, Ballast Transformer (used on A037458-01 assembly) For ireland-Built Upright Cabinet 142028-002 50 Hz, 118 V, Ballast Transformer (used on A037458-02 assembly) For U.S- and Ireland-Built Upright Cabinet A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥%-Inch Wide x j-Inch Thick 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 003053-01 Upper and Lower Attraction Glass Retainer 037469-01 Steel Tube Bracket 039366-01 Tube and Speaker Board 039418-01 Attraction Glass with Graphics 148001-013* 6 x 91nch Oval, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker 179035-001 2-Pin Fluorescent Tube Holder *148001-001 6 x 9-Inch Oval, 4-Ohm, 6-Ounce, High-Fidelity Speaker—mounted to the cabinet near the coin door, behind speaker grille part no. 039144-01

3417

Page 44

Maintenance, Repair, and Parts

Sit-Down Cabinet

Replacing the Front Speakers:

  • For the right speaker, unlock and open the rear access panel (see Figure 3-10). For the left speaker, open the control panel (see Figure 3-3).
  • Unplug the two plug-in connectors. 3, Remove the two screws that secure the speaker to the wood speaker panel. Pole Position

Replacing the Seat-Panel Speakers: ADS

  • Remove the six wood screws that secure the seatback panel to the cabinet (see Figure 3-10).
  • Lean the seat-back panel forward. Disconnect the two plug-in connectors on each speaker.
  • Remove the seat-back panel from the player area of the cabinet.
  • Remove the four screws that secure each speaker to the seat-back panel.
  • Reassemble in reverse order.

Figure 3-10 Sit-Down Cabinet Speaker Removal

3-18

Page 45

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 46

Maintenance, Repair, and Parts

D. Video Display

WARNING SHOCK HAZARD The following procedure should only be perjormed by a qualified service technician. Before removing or repairing the video display, turn the game off. High voltages may exist in any video display, even with power disconnected. Use extreme
caution and do not touch electrical parts of the display yoke area with your hands or with metal objects in your hands! Discharge the high voltage from the cathode ray tube as follows: First, attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Then, wait two minutes and discharge the anode again. IMPLOSION HAZARD If you drop the display and the picture tube breaks, /t will imp/ode! Shattered glass and the yoke can fly six feet or more from the implosion. Use care when replacing any display.

Removing the Video Display From the Upright Cabinet:

1. From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-17). Remove the four sets of hardware that secure the video display to the wood display shelf. Open the control panel (see Figure 3-3). Remove the three wing nuts (located on the displayshield support) that secure the dashboard panel to the cabinet. From the front of the cabinet, lift off the dashboard panel. Remove the hardware that secures the display-shield retainer. Lift the display shield up and out of the cabinet. Remove any staples that may secure the bezel to the cabinet. Then, carefully remove the cardboard bezel. Carefully pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.

3-20 Pole Position

Removing the Video Display From the Sit-Down Cabinet:

1. From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-17). Remove the four sets of hardware that secure the video display to the wood display shelf. Open the control panel (see Figure 3-3). Move to the player area of the cabinet. Grasp the bottom edge of the video display shield and slide the shield out and down. Make sure the foam tape on the bottom of the shield is in good condition. Remove any staples that may secure the bezel to the cabinet. Then, carefully grasp the bottom edge of the cardboard bezel and remove it from the cabinet. Pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.

Page 47

Pole Position Maintenance, Repalr, and Parts

039148-01 | (Ghield) 039149-01 039371-01 i (Bezel) (Retainer) 039417-01 (Shield) 039407-01 | ! (Bezel) d 92-049 (Electrohome display) é or 139003-1004 (Matsushita display)

(Shelf) ji 039123-02 Jf (Shelf) & A

Figure 3-11 Video Display Upright and Sit-Down Cabinets Parts List

Part No. Description For Upright Cabinet 039363-02 Display Shelf 039371-01 Retainer 039407-01 Display Bezel 0394 17-01 Display Shield For Sit-Down Cabinet 039123-02 Display Shelf 039148-01 Display Shield 039149-01 Display Bezel

For Upright and Sit-Down Cabinets 92-049 19-Inch Electrohome Color Raster-Scan Display Alternate display is part no. 139003-1004-—19-Inch_ Matsushita Color Raster-Scan Display

3-21

Page 48

Maintenance, Repair, and Parts Pole Position

E. Utility Panel

A—warninc—A: Before removing or repairing the utility panel, turn the game off. Players may receive an electrical shock if the utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal screw on the back of the coin counter. The utility panel is located inside the upper coin door. This panel includes the volume control(s), self-test switch, auxiliary coin switch, and the coin counter(s) (see Figure 3-12). The auxiliary coin switch is used to credit the game without tripping the coin counter.

NOTE Only Ireland-Built cabinets have two coin counters.

A039254-01 (Dual component 03945701 harness) (Utiity pane— US.-Built Upright only) cil panel 039295-01 hi (Utility panel) larness)

A039248-01 (Vol. control harness) 478070-001 a » (Vol. control knob)

75-9168, (Hex nut) 75-9910W0 (Stamped nut) (Auxiliary coin switch) SELF-TEST SWITCH (69-001)

SWITCH NOT USED

Figure 3-12 Utility Panel Assembly A039391-xx D

3-22

Page 49

Pole Position Maintenance, Repair, and Parts

Utility Panel Assembly Parts List

Part No. Description For U.S-Built Upright Cabinet 039457-01 Utility Panel (for 2 volume controls) For lreland-Built Upright Cabinet 039295-01 Utility Panel (for 4 volume controls) For U.S-and Ireland-Built Upright Cabinet A038004-01 Utility Panel Harness Assembly A039254-01 Dual Component Harness Assembly For U.S-and Ireland-Built Sit-Down Cabinet A039248-01 Volume Control Harness Assembly 039295-01 Utility Panel (for 4 volume controls) For U.S-and Irefand-Built Upright and Sit-Down Cabinets A002465-01 6 V Coin Counter 19-9032 50 Q, 12.5 W Volume Control 62-041 SPST Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 72-HA4608S #6-32 x ¥2-Inch Thread-Forming Screw 75-916S #6-32 Steel Machine Hex Nut 75-9910W0 #15/32-32 Stamped Nut 178070-001 Volume Control Knob

3-23

Page 50

Maintenance, Repair, and Parts Pole Position

FE. Coin Doors

170000-001 (Lamp) Z 179047-001 : 9915023

(Lamp Base) : a Plate)

99-15056 (Screw for Bezel) 99-15026 99-15040 a (Coin Inlet) (Lever) 99-15025 oe (Coin Inlet)

ea

S| y ls L 99-15054 ~~ (Pivot for Lever)

99-15028 75.9148 (Coin Return Box) (Hex Nut) 75.056 . (Lock Wash.) NN,

99-15075 S

(Sw. Adjuster) 4

99-15029 (Bracket)

(Switch)

T2A414S (Screw)

Figure 3-13 Vertically Mounted Coin Door 171034-xxx

3-24

Page 51

Pole Position Maintenance, Repair, and Parts

99-15038 A037542.01 (Bezel for Button) (Harness—not snown)

99-15073 (Upper Door), 99-15001 thru 99-15011 (Return Button) ™.

9915063 Screw) 9915052 (Spring for Button)

‘99-5039 (Bezel for Cover) 9915067 (Lock Assy.)

038091-01 (Coin Box) 99-15066 (Screw)

9915074 (Lower Door)

9915070 (Doors and Frame} 99-15072 (Door Frame)

171034-001 — U.S. 258/25¢ Coin Door 171034006 — U.K. 20 P/50 P Coin Door 171034011 — German 1 MIS M Coin Door 171034003 — Canadian 25¢/25¢ Coin Door 171034.009 — German 2 M/1 M Coin Door 171034.015 — French 2 F/1 F Coln Door 171034-005 — U.K. 10 P/5S0 P Coin Door 171034-010 — German 2 M/5 M Coin Door

Figure 3-13 Vertically Mounted Coin Door, continued 171034-xxx

3-25

Page 52

Maintenance, Repair, and Parts Pole Position

Vertically Mounted Coin Door Parts List

Part No. Description A037542-01 Harness Assembly 72-1414S #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Steel Machine Hex Nut 7534145 #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Retum Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for U.S. 25¢ 9915052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 #4-40 x %.-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly} Acceptable substitute is part number A037491-01 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

3-26

Page 53

Pole Position Maintenance, Repair, and Parts

99-10140 (Panel assy.)

75.9488 a (Locknut) . 99-10116 (Lever)

9910152 (Right coin inlet)

99-10096 (Fastener) 75-9445, (Hex nut)

99-10151 (Left coin inlet)

99-10080 (Lamp socket). SS , 70-11-47 as (Lamp)

S

99-10104 (Bar retainer) 72-9406S (Screw) 99-0147 (Harness)

99-10154 (Bracket assy.) |

99-1042 thru 99-1045 (Coin switch assy.) 99-10153 (Coin return box) i$ Ng ! a 65-441 <4 (Coin switch) os “ail

™~ 99-10075 thru 99-10078 (Switch wire) 99-1008 (Retainer)

Figure 3-14 American-Made Coin Door 171027-001 A

3-27

Page 54

3-28 Figure 3-14 American-Made Coin Door, continued 171027-001 A 72-JA1405B (Screw)

038091-01 (Coin box)

fo 72-HA1404C 99-10148 (Lock)

99-10117 99-10142

(Coin return door) (Button housing)

99-10141 (Coin return cover)

99-10149 (Service door) Maintenance, Repair, and Parts a Pole Position

Page 55

Pole Position Maintenance, Repair, and Parts

American-Made Coin Door Parts List Assemblies and components in the following parts list are shown in Figure 3-14.

Part No. Description

171006-035 Metal Coin Mechanism for U.S. $.25 65-4416 Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x ¥%;Inch Truss-Head Screw 72-HA1404C, #4-40 x V4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x %4-Inch Pan-Head Screw 75-994S #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (included in coin switch assembly) 99-10076 Switch wire {included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115, Spring 99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145 Offset Cam (includes 99-10148—Lock) 99-10146 Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10749 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-1053 Coin Return Box 99-10154 Bracket Assembly

3-29

Page 56

Maintenance, Repair, and Parts Pole Position

G. Printed-Circuit Boards ‘A037767-01 (EMI Shield PB) 039378-03 (Retainer) Shield PCB 176015-110 See Figure 3:20 087873-01 (Screw) (Spacer)

A039431-01 (End PCB)

721404F (Screw) 034536-02 (Foam pad) ‘A037701.01 72:1604F (EMI cage} (Screw)

‘A038187-21 A038185-21 (Pole Position Video PCB) eet (Pole Position CPU PCB) (Washer) NOTE 178045-442 The FCC requires that the game (Fastener) PCB be housed in the EMI cage with the Shield PCB attached.

Reo! 176015-110 ap 202548505 (Screw) (Regulator! 175004-708 Audio I] PCB) (Washer)

*Steps 1, 10, and 11 are not illustrated.

Figure 3-15 Removing the Printed-Circuit Boards

Page 57

Pole Position

WARNING

Before you remove or repair any printed-circuit board, turn ihe game off.

Removing the Printed-Circuit Boards: Removing the Game PCBs from the EMI Cage

  • Open the rear access panel.
  • The game printed-circuit boards (PCBs) are located inside the electromagnetic interference (EMI) cage (see Figure 3-15}. The EMI cage is located on the cabinet wail of the Upright game and on the inside of the rear access panel of the Sit-Down game. Unplug the two harness edge-connectors from the EMI Shield PCB.
  • To remove the game PCBs, pull the eight nylon snap-in fasteners on the EMI Shieid PCB to the unlocked position. Carefully slide the Shield PCB and attached PCBs straight out of their guides. Be carefui not to twist the boards, as this may loosen connections or components, Removing the EM! Shield PCB from the Game PCBs
  • Remove the two pan-head screws that connect the EM! Shield PCB to the spacers,
  • Push the EMI Shield PCB off the game PCBs by applying pressure with your thumbs to the edge connec- Maintenance, Repair, and Parts
  • Unplug the End PCB that connects the two game PCBs.
  • Determine which PCB you need to repair or replace, and remove the two pan-head screws that connect that PCB to the spacers. Replace or repair as required, and reinstall the PCBs. (Make sure the foam vibration damper is placed between the game PCBs.) Removing a Regulator/Audio i! PCB:
  • To remove a Reguilator/Audio I! PCB, disconnect the small hamess connectors on the board. 9 Remove the hardware that secures the Regulator/Audio I! PCB to the cabinet, and carefully lift the board from the retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required and reinstall the PCB.
CAUTION

Make sure that the connectors on each PCB are properiy plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

  • Close and lock the rear access panel. tors. 11. Important: Perform the self-test.

Printed-Circuit Board Mounting Hardware Parts List

Assemblies and components in the following parts list are shown in Figure 3-15.

Part No. Description

U.S-Built Upright and Sit-Down Cabinets A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) 72-1404F #4-40 x %4-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x %4-Inch Cross-Recessed Steel Screw 034536-02 Foam Pad 037873-01 Spacer 039378-03 Dual-Slotted Retainer 175004-708 #8 Fiber Washer 175009-221 Plastic Spacer (for EMI shield PCB) 176015-110 #10 x %-Inch Cross-Recessed Pan-Head Screw 178044-242 Grommet 178045-442 Snap-In Fastener Ireland-Built Upright and Sit-Down Cabinets* 72-6624S #6 x 1 Y2-Inch Cross-Recessed Pan-Head Tapping Screw 034536-02 Foam Pad 03915702 Dual-Slotted PCB Retainer 175004-708 #8 Fiber Washer 176015-110 #10 x %Inch Cross-Recessed Pan-Head Screw 178020-750 Nylon Spacer

*Not shown in illustration

3-31

Page 58

Pole Position

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

co!

Esse] thse] isl ue tisisy, {lees fee] a

fed rs RY ARE ep a i as cay is) tose] Tp RSs 3,7 GAS com feaee far BSS ee Weer) Ss ae E=

Baia

‘aa wae @ ay eS Maintenance, Repair, and Parts

Figure 3-16 Central Processing Unit (CPU) Printed-Circuit Board Assembly A039185-21 B

3-32

Page 59

Poie Position

Parts List

Components in the following parts list are shown in Figure 3-16. Figure 3-16 Central Processing Unit Printed-Circuit Board Assembly Maintenance, Repair, and Parts

DesignatorDescriptionPart No.

Capacitors

C2-C50.01 pF, 100 V Radial-Lead Mylar Capacitor21-101103
cé33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor128002-330
c70.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
cg10 uF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250106
C100.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C147 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C120.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C13,0.01 uF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C14, C150.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C16-C230.01 uF, + 80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C24, C250.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C2647 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C27, C280.0022 uF, + 10%, 100 V Radial-Lead Plastic Film Capacitor121022-222
C29, C300.022 uF, 100 V Radial-Lead Mylar Capacitor21-101223
C31, C320.07 uF, + 80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-103
C33, C340,047 uF, 100 V Radial-Lead Mylar Capacitor21-101473
C350.022 uF, 100 V Radial-Lead Mylar Capacitor21-101223
C360.0047 yF, 100 V Radial-Lead Mylar Capacitor21-101472
C370.001 yF, 100 V Radial-Lead Mylar Capacitor21-101102
C380.0047 yF, 100 V Radial-Lead Mylar Capacitor21-101472
C39, C400.01 uF, 100 V Radial-Lead Mylar Capacitor21-101103
C4147 uF, 10 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-100476
C42, C430.0047 uF, 100 V Radial-Lead Mylar Capacitor21-101472
C44, C450.001 uF, 100 V Radial-Lead Mylar Capacitor21-101102
C46.470 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C47-C5622 uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor24-160226

Acceptable substitute is part no, 24-100477

C57-C840.1 uF, + 10%, 25 V Ceramic-Disc Axial-Lead Capacitor122005-104
C820,001 :F, 100 V Radial-Lead Mylar Capacitor21-101102

Diodes

CR1Type-MV5053 Light-Emitting Diode38-MV5053,
CR26.2 V, +5%, 1 W Type-1N4735A Zener Diode131009-001
CR3-CR5100 V, Type-1N914 Switching Diode31-1N914
CRB3.3 V +5% Zener Diode131014-001
CR7-CR12100 V, Type-1N914 Switching Diode31-1N914

Integrated Circuits

2NType-12L6 Programmable-Array Logic 1137280-001
3AType-Z8002 16-Bit Microprocessor137275-001
3cType-74LS373 Integrated Circuit37-74LS373
SF, 3HCustom integrated Circuit 10137281-001

(Continued on next page)

3-33

Page 60

Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued Pole Position

DesignatorDescriptionPart No.
3M, 4CType-74LS373 Integrated Circuit37-74LS373
4F, 4HCustom Integrated Circuit 10137281-001
4MType-74LS373 Integrated Circuit37-74LS373
4NType-Z8002 16-Bit Microprocessor137275-001
5AType-74LS74 Integrated Circuit37-74LS74
5CType-12L6 Programmable-Array Logic 1137280-001
5DType-74LS367 Integrated Circuit37-74.S367,
5EType-74LS244 Integrated Circuit37-74LS244
5dType-74LS367 Integrated Circuit37-74LS367
5KType-74LS244 Integrated Circuit37-74LS244
5LType-74LS368 Integrated Circuit137 168-001
5MType-74LS158 Integrated Circuit137203-001
5NType-74LS74 Integrated Circuit37-7ALS74
6AType-74LS161 Integrated Circuit37-74LS161
6cType-74LS74 Integrated Circult37-74LS74
6D-6FType-74LS367 Integrated Circuit37-74LS367
6HCustom Integrated Circuit 08137186-001
6J, 6KType-74LS157 Integrated Circuit37-74LS 157
6LType-74LS109 Integrated Circuit37-74LS109
6MType-74LS00 Integrated Circuit37-74LS00
6NType-74S163 Integrated Circuit137274-001
7GType-10L8 Programmable-Array Logic 3137279-001
7DType-Z80A 8-Bit Microprocessor137194-001
7MCustom Integrated Circuit 07137193-001
7NType-74S04 \ntegrated Circuit37-74804
8DType-74LS138 Integrated Circuit137177-001
8EType-74LS259 Integrated Circuit37-74LS259
8FType-74LS367 Integrated Circuit37-74LS367
8HCustom Integrated Circuit 08137186-001
8UType-ADC0804 Integrated Circuit137273-001
8KType-4066 Integrated Circuit37-4066
8LType-4584B Integrated Circuit37-4584B
8MType-74LS04 Integrated Circuit37-74LS04
9ECustom Integrated Circuit 52137284-001
OFACustom Integrated Circuit 54137285-001
9FBType-LM324 Integrated Circuit37-LM324
9HCustom Integrated Circuit 06137192-001
9KCustom Integrated Circuit 53137188-001
9MCustom Integrated Circuit 51137187-001
10AType-74LS138 Integrated Circuit137177-001
10CType-74LS374 Integrated Circuit37-74LS374
10DType-74LS 174 Integrated Circuit37-74LS 174
10E, 10FType-74LS283 Integrated Circuit137204-001
10H, 10JType-74LS273 Integrated Circuit37-74LS273
10K, 10LType-4066 Integrated Circuit37-4066
1AType-74LS174 Integrated Circuit37-74LS 174
1cType-7497 Integrated Circuit37-7497
HEType-74LS273 Integrated Circuit37-74LS273

(Continued on next page)

Page 61

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
q1FType-4051 Integrated Circuit137277-001
11HType-74LS174 Integrated Circuit37-74LS174
AWType-74LS273 Integrated Circuit37-74LS273
11K~11MType-4066 Integrated Circuit37-4066
120Type-74LS174 Integrated Circuit37-74LS174
12BType-7497 Integrated Circuit37-7497
12CType-74LS161 Integrated Circuit37-74LS161
120Type-74L$393 Integrated Circuit37-74LS393
12H, 12J, 12MType-LM324 Integrated Circuit37-LM324

Random-Access Memories

7ECMOS Random-Access Memory137278001
7d, 7KRandom-Access Memory137199-001

Read-Only Memories

cgElectrically Programmable Read-Only Memory*136014-106
3EElectrically Programmable Read-Only Memory*136014-103.
3LElectrically Programmable Read-Only Memory*136014-101
4eElectrically Programmable Read-Only Memory*136014-104
4Electrically Programmable Read-Only Memory*136014-102
TFElectrically Programmable Read-Only Memory136014-116
7HElectrically Programmable Read-Only Memory*136014-105
7LProgrammable Read-Only Memory136014-117
11DProgrammable Read-Only Memory136014-118
12EElectrically Programmabie Read-Only Memory*136014-111
12FElectrically Programmable Read-Only Memory*136014-110

Resistors

Rt220 2, +5%, ¥% W Resistor110000-221
R2-R82.2 kQ, +5%, V4 W Resistor140000-222
RO1k, +5%, % W Resistor110000-102
R10-R162.2 kQ, +5%, 14 W Resistor110000-222
R17-R201kQ, +5%, % W Resistor110000-102
R21-R261kQ, +5%, % W Resistor110000-102
R27-R342.2 kQ, +5%, % W Resistor110000-222
R351kQ, +5%, %4 W Resistor110000-102
R36-R382.2 kQ, +5%, % W Resistor110000-222
R39-R431kQ, +5%, va W Resistor110000-102
R45.47 Q, +5%, V4 W Resistor110000-470
R46, R471kQ, +5%, % W Resistor116000-102
R49-R51220 2, +5%, V4 W Resistor110000-221
R52470 Q, +5%, % W Resistor110000-471
R53.1kQ, +5%, % W Resistor110000-102
R54470 2, +5%, %4 W Resistor410000-471

(Continued on next page)

“Acceptable substitute is part no. 137276-003

3-35

Page 62

Maintenance, Repair, and Parts Pole Position

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
RS5, R561kQ, 5%, % W Resistor110000-102
R5?7-R60470 2, +5%, % W Resistor110000-471
R614.7 kQ, +5%, V4 W Resistor110000-472
R6210 kQ, +5%, % W Resistor110000-103
R6322 kQ, +5%, V4 W Resistor110000-223
R6447 kQ, +5%, % W Resistor110000-473
R654.7 kQ, +5%, ¥4 W Resistor110000-472
Reé10 k2, +5%, %4 W Resistor110000-103
R6722 kQ, +5%, V4 W Resistor110000-223
R6847 kQ, 5%, Vs W Resistor110000-473
R694.7 kQ, +5%, V4 W Resistor110000-472
R7010 kQ, +5%, 4 W Resistor110000-103
R7122 kQ, 45%, % W Resistor110000-223
R7247 kQ, +5%, %4 W Resistor110000-473
R734.7 kQ, +5%, V4 W Resistor110000-472
R7410 kQ, +5%, %4 W Resistor110000-103
R7522 kQ, +5%, Vs W Resistor410000-472
R7647 kQ, +5%, Vs W Resistor110000-473
R77-R801kQ, +5%, Vv W Resistor110000-102
R81220 2, +5%, V4 W Resistor110000-221
R821kQ, +5%, % W Resistor110000-102
R83470 Q, +5%, 4 W Resistor110000-471
R841kQ, +5%, % W Resistor110000-102
R852.2 kQ, +5%, V4 W Resistor110000-222
R86330 Q, +5%, v4 W Resistor110000-331
R871kQ, +5%, % W Resistor110000-102
Ree22 k2, +5%, %4 W Resistor110000-223
R89-R921kQ, +5%, % W Resistor110000-102
RQ3, ROA330 , +5%, 4 W Resistor110000-331
R951kQ, +5%, % W Resistor110000-102
R964.7 kQ, +5%, Vs W Resistor110000-472,
R97220 Q, 5%, v4 W Resistor110000-221
R98,2.2 kQ, +5%, % W Resistor110000-222
R99220 2, +5%, v4 W Resistor110000-221
R10122 kQ, +5%, Y4 W Resistor110000-222
Rt02, R1041kQ, +5%, %4 W Resistor110000-102
R103, R1074.7 kQ, +5%, % W Resistor110000-472
R106, R108-R1151kQ, +5%, 1% W Resistor110000-102
Ri161.5 kQ, +5%, Vs W Resistor110000-152
RiW71kQ, +5%, % W Resistor110000-102
R11847 kQ, +5%, % W Resistor110000-472
R1910 k2, +5%, % W Resistor110000-103
R120, R12122 kQ, + 5%, V4 W Resistor110000-223
R122120 kQ, +5%, %4 W Resistor110000-124
R123,470 2, +5%, % W Resistor410000-471
R12447 kQ, +5%, V4 W Resistor110000-473
R12512 kQ, +5%, % W Resistor110000-123
R1264.7 kQ, +5%, Vs W Resistor110000-472

(Continued on next page)

3-36

Page 63

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R127, R1282.2 kQ, +5%, % W Resistor110000-222
R129, R1303.3 kQ, +5%, % W Resistor110000-332
R13110 k2, +5%, % W Resistor110000-103
R13222 kQ, +5%, v4 W Resistor110000-223
R13315 kQ2, +5%, 1% W Resistor110000-153
R134120 kQ, +5%, V4 W Resistor110000-124
R135470 Q, +5%, ¥% W Resistor110000-471
R136AT kQ, + 5%, % W Resistor110000-473
R13715 kQ, +5%, % W Resistor110000-153
R13810 kQ, +5%, % W Resistor110000-103
R13922 kQ, +5%, % W Resistor110000-223
R140180 kQ, +5%, % W Resistor110000-184
R141470 O, +5%, % W Resistor110000-471
R142, R14322 kQ, +5%, % W Resistor110000-223
R144-R1511kQ, +5%, Ys W Resistor110000-102
R15247 kQ, +5%, v4 W Resistor110000-473
R153470 Q, 5%, % W Resistor110000-471
R15410 kQ, +5%, % W Resistor110000-103
R15582 kQ, +5%, % W Resistor110000-823
R156, R15747 kQ, +5%, V4 W Resistor110000-473
R15822 kQ, +5%, % W Resistor110000-223
R15947 kQ, +5%, “4 W Resistor110000-473
R160100 k2, +5%, %4 W Resistor110000-104
R161~R1652.2 kQ, +5%, % W Resistor110000-222
R1661kQ, +5%, va W Resistor110000-102
R1672.2 kQ, +5%, % W Resistor110000-222
R1684.7 kQ, +5%, % W Resistor110000-472
R169220 kQ, +5%, 1% W Resistor110000-224
R170390 k2, +5%, 14 W Resistor110000-394
R1714.7 kQ, +5%, % W Resistor110000-472
R17215 kQ, +5%, % W Resistor110000-153
R17347 kQ, +5%, 4 W Resistor110000-473
R17433 kQ, +5%, %4 W Resistor110000-333
R175,10 kQ, +5%, % W Resistor110000-103
R17647 kQ, +5%, Vs W Resistor110000-473
R1771kQ, +5%, % W Resistor110000-102
R1787.5 kQ, +5%, Vs W Resistor110000-752
R179330 kQ, +5%, %4 W Resistor110000-334
R180, R18147 kQ, +5%, V4 W Resistor110000-473
R1821kQ, +5%, % W Resistor110000-102
R183,22 kQ, +5%, % W Resistor110000-223,
R18415 kQ, +5%, % W Resistor110000-153
R18510 k2, +5%, % W Resistor110000-103
Ri861kQ, +5%, Vs W Resistor110000-102
R187330 kQ,+5%, % W Resistor110000-334
R188,10 kQ, +5%, % W Resistor110000-103
R189, R19047 kQ, +5%, % W Resistor110000-473
R1911kQ, +5%, % W Resistor110000-102

(Continued on next page)

3-37

Page 64

Maintenance, Repair, and Parts Pole Position

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R19275 kQ, +5%, V4 W Resistor110000-753
R19315 kQ, +5%, V4 W Resistor110000-153
R19447 kQ, +5%, V4 W Resistor110000-473,
R19510 kQ, +5%, Vs W Resistor110000-103
R1961kQ, +5%, % W Resistor110000-102
R197, R19847 kQ, +5%, V4 W Resistor110000-473
R1991kQ, +5%, V% W Resistor110000-102
R20047 k2Q, +5%, Vs W Resistor110000-473
R20115 kQ, +5%, %4 W Resistor110000-153
R20210 kQ, +5%, % W Resistor110000-103
R2031 kQ, +5%, % W Resistor410000-102
R204, R20547 kQ, +5%, Vs W Resistor110000-473
R2061kQ, +5%, V4 W Resistor110000-102
R20720 kQ, +5%, % W Resistor110000-203
R20810 kQ, +5%, % W Resistor110000-103
R20920 kQ, +5%, V4 W Resistor110000-203
R21010 kQ, +5%, % W Resistor110000-103
R21120 kQ, +5%, % W Resistor110000-203
R21210 kQ, +5%, % W Resistor110000-103
R21320 kQ, +5%, V4 W Resistor110000-203
R21410 kQ, +5%, 4 W Resistor110000-103
R21520 kQ, +5%, % W Resistor110000-203
R21610 k2, +5%, % W Resistor110000-103
R21720 kQ, +5%, %4 W Resistor110000-203
R21810 kQ, +5%, % W Resistor110000-103
R21920 kQ, +5%, %4 W Resistor110000-203
R22027 kQ, +5%, Vs W Resistor110000-273
R2231kQ, +5%, % W Resistor410000-102
R225-R2311kQ, +5%, “4 W Resistor110000-102
R231-R2382.2 kQ, +5%, V4 W Resistor110000-222
R239-R2441kQ, +5%, % W Resistor110000-102
R245100 2, +5%, % W Resistor110000-101
R246150 kQ, +5%, % W Resistor110000-154
1E2.2 kQ, +2%, Dual-Inline-Package Resistor Network118003-222
ON1kQ, +2%, Dual-Inline-Package Resistor Network118003-102

Sockets

3A40-Contact Medium-insertion-Force Integrated Circuit Socket79-42C40
3E, 3F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
3H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
3k28-Contact Medium-Iinsertion-Force Integrated Circuit Socket79-42C28
4E, 4F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4H28-Contact Medium-Insertion-Force integrated Circuit Socket79-42C28
4L28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4N40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40

(Continued on next page)

3-38

Page 65

Pole Position Maintenance, Repair, and Parts

Central Processing Unit Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
6H-9H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
7D40-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C40
7E, 7F24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
7H28-Contact Medium-insertion-Force Integrated Circuit Socket79-42628
7M28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8A28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8c28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9c28-Contact Medium-insertion-Force Integrated Circuit Socket79-42C28
9E42-Contact Medium-Insertion-Force integrated Circuit Socket79-42C42
OFA28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
9K42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
9M42-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C42
12E, 12F28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28

Switches

QJA8-Station, Single-Throw, Dual-inline-Package Bit Switch66-118PIT
9L8-Station, Single-Throw, Dual-Inline-Package Bit Switch66-118PIT

Transistors

QiType-2N3906 40 V, 1 W, PNP Transistor33-2N3906
Q2Type-2N3904 60 V, 350 mW, NPN Transistor34-2N3904
Q3Type-MPS-A92 300 V, 500 mA, PNP Transistor33-MPSA92
QaType-2N3904 60 V, 350 mW, NPN Transistor34-2N3004
Q5, 06Type-2N6044 80 V, 8 A, Darlington NPN Transistor34-2N6044

Miscellaneous

BT13.6 V, 100 mA Nickel-Cadmium Battery171028-001
W1Lead-Spring Socket Terminal179131-001

Test Point Acceptable substitute is part no. 020670-07 179051-001 Jumper Staple 15009-001

Q5, Q6Nylon Snap-In Fastener81-4302

3:39

Page 66

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 67

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

C2470 pF, 25 V Aluminum Electrolytic Axial-Lead Capacitor24-250477
C3-C1722 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor24-160226
C18-C570.1 pF, + 80, -20%, 50 V Ceramic Disk Radial-Lead Capacitor122002-104
C5868 pF, 100 V, Mica Capacitor128002-680
cso22 pF, 100 V, Mica Capacitor128002-220

Diodes

CRIType-MV5053 Light-Emitting Diode38-MV5053
CR2‘Type-1N4735A, 6.2 V, 1 W Zener Diode131009-001

Inductors

L1-L31 pH, Ye W Inductor141007-001
L4100 pH, + 10% Inductor141002-001

Integrated Circuits

2AType-74LS138 Integrated Circuit137177-001
2EType-74LS74 Integrated Circuit37-74LS74
2HType-74LS139 Integrated Circuit37-74LS139
2dType-74LS10 Integrated Circuit37-74LS10
2KType-74LS368 Integrated Circuit137168-001
3BType-74LS283 Integrated Circuit137204-001
3cType-74LS283 Integrated Circuit137204-001
3DType-74LS283 Integrated Circuit137204-001
3HType-74LS175 Integrated Circuit37-74LS175
SJ, 4dType-74LS174 Integrated Circuit37-74LS174
3KType-74LS283 Integrated Circuit137204-001
3LType-74LS283 Integrated Circuit137204-001
3MType-74LS02 Integrated Circuit37-74LS02
4BType-74LS367 Integrated Circuit37-74LS367
4cType-74LS367 Integrated Circuit37-74LS367
4HType-74LS157 Integrated Circuit37-74LS157
4KType-74LS174 Integrated Circuit37-7ALS 174
4M, 5MType-74LS298 Integrated Circuit137201-001
4N, 5NType-74LS283 Integrated Circuit137204-001
5BType-74LS174 Integrated Circuit37-7ALS 174
5CType-74LS174 Integrated Circuit37-74LS174
5DType-74LS174 Integrated Circuit37-74LS174
5EType-74LS245 Integrated Circuit37-74LS245
SF, 6FType-74LS245 Integrated Circuit37-74LS245
5HType-74LS175 Integrated Circuit37-74LS175
5dType-74LS273 Integrated Circuit37-74LS273
6AType-74S04 Integrated Circuit37-74S04
6BType-74LS368 Integrated Circuit137 168-001
6CType-74LS08 Integrated Circuit37-74LS08
6HType-74LS245 Integrated Circuit37-74LS245
6dType-74LS245 Integrated Circuit37-74LS245
6KType-74LS245 Integrated Circuit37-74LS245
6M, 7MType-74LS273 Integrated Circuit37-74LS273
7BType-74S163 Integrated Circuit Acceptable substitute is part no.137274-001

137287-001 or -002

7CType-74S04 Integrated Circuit37-74S04
7DType-74LS32 Integrated Circuit37-74LS32

(Continued on next page)

3-41

Page 68

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
7LType-74LS273 Integrated Circuit37-74LS273
8BType-74S00 Integrated Circuit37-74S00
8C,9CType-74LS157 Integrated Circuit37-74LS157
8DType-74LS158 Integrated Circuit137203-001
8EType-74LS158 Integrated Circuit137203-001
8L,9LType-74LS174 Integrated Circuit37-74L8174
9BType-74LS20 Integrated Circuit37-74LS20
9DType-74LS298 Integrated Circuit137201-001
9E, 10EType-74LS257 Integrated Circuit37-74LS257
9HType-74LS161 Integrated Circuit37-74LS161
ouType-74LS161 Integrated Circuit37-74LS161
9KType-7497 Integrated Circuit37-7497
9M, 10MType-74LS283 Integrated Circuit137204-001
9NType-74LS85 Integrated Circuit37-74LS85
10BType-74LS74 Integrated Circuit37-74LS74
10CType-74LS174 Integrated Circuit37-74LS174
10DType-74LS368 integrated Circuit137168-001
10HType-74LS161 Integrated Circuit37-74LS161
10JType-74LS161 Integrated Circuit37-74L5161
10KType-74LS161 Integrated Circuit37-74LS161
10L.Type-74LS161 Integrated Circuit37-74LS161
10NType-74LS85 Integrated Circuit37-74LS85
11BType-74107 Integrated Circuit Acceptable substitute is part no.37-74107

137169-001

11FType-74LS174 Integrated Circuit37-74LS174
41HType-74LS174 Integrated Circuit37-74LS174,
WdType-74LS273 Integrated Circuit37-74LS273
11KType-74L$139 Integrated Circuit37-74LS139
ILType-74LS373 Integrated Circuit37-74LS373
11MType-74LS373 Integrated Circuit37-74LS373
12BType-74LS08 Integrated Circuit37-74LS08
12FType-74LS86 Integrated Circuit37-74LS86
13FType-74LS20 Integrated Circuit37-74LS20

For -21 version only

2FType-07 Custom Integrated Circuit137193-001
3NType-02 Custom Integrated Circuit137190-001
4DType-09 Custom Integrated Circuit137282-001
BL, 6L.Type-03 Custom Integrated Circuit137283-001
7EType-04 Custom Integrated Circuit137191-001
8NType-02 Custom Integrated Circuit137190-001
13HType-02 Custom Integrated Circuit137190-001

Random-Access Memories

SE, 4ERandom-Access Memory (200 ns) Acceptable substitute is part no.137198-001

137211-001 (150 ns)

SF, 4FRandom-Access Memory (200 ns) Acceptable substitute is part no.137198-001

137211-001 (150 ns)

7F, 8FType-2114-2 (200 ns) Random-Access Memory90-7036
7H, 8HType-2114-2 (200 ns) Random-Access Memory90-7036
7J, BuType-2114-2 (200 ns) Random-Access Memory90-7036
7K, 8KType-2114-2 (200 ns) Random-Access Memory90-7036
QF, 10F55 ns Random-Access Memory137199-001

(Continued on next page)

Page 69

Pole Position Maintenance, Repair, and Parts

Pole Position Video Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.

Programmable Read-Only Memories

2BType-82S129(17) Programmable Read-Only Memory136014-144
2cType-82S129(16) Programmable Read-Only Memory136014-143
2DType-82S 129(15) Programmable Read-Only Memory136014-142
4uType-82S137(12) Programmable Read-Only Memory136014-145
5KType-82S 129(11) Programmable Read-Only Memory136014-141
6DType-82S123(14) Programmable Read-Only Memory136014-136
6EType-82S 123(13) Programmable Read-Only Memory136014-135
8MType-82S 129(10) Programmable Read-Only Memory136014-140
1cType-82S129(9) Programmable Read-Only Memory136014-139
11DType-82S129(8) Programmable Read-Only Memory136014-138
11EType-82S129(7) Programmable Read-Only Memory136014-137
12HType-82S137(6) Programmable Read-Only Memory136014-146

For -21 version only

aLElectrically Programmable Read-Only Memory136014-127
2MElectrically Programmable Read-Only Memory136014-128
2NElectrically Programmable Read-Only Memory Acceptable substitute136014-134

is part no, 137205-001

6NElectrically Programmable Read-Only Memory Acceptable substitute136014-133

is part no. 137205-001

7NElectrically Programmable Read-Only Memory Acceptable substitute136014-132

is part no. 137205-001

11NElectrically Programmable Read-Only MemoryAcceptable substitute136014-231

is part no. 136014-131

12dElectrically Programmable Read-Only Memory136014-120
12KElectrically Programmable Read-Only Memory136014-122
12LElectrically Programmable Read-Only Memory136014-124
12NElectrically Programmable Read-Only Memory136014-126
13dElectrically Programmable Read-Only Memory136014-119
13KElectrically Programmable Read-Only Memory136014-121
13LElectrically Programmable Read-Only Memory136014-123
13NElectrically Programmable Read-Only Memory136014-125

Resistors

R1-R92.2kQ, +5%, % W Resistor110000-222
R10-R241kQ, +5%, 4 W Resistor110000-102
R25-R40470 Q, +5%, % W Resistor110000-471
R41-R484.7 kQ, +5%, Va W Resistor110000-472
R49-R521kQ, +5%, % W Resistor110000-102
R55-R58.1kQ, +5%, % W Resistor110000-102
R59220 2, +5%, V4 W Resistor110000-221
R60470 2, +5%, v4 W Resistor110000-471
R611kQ, +5%, % W Resistor110000-102
R622.2 kQ, +5%, V4 W Resistor110000-222
R66220 Q, +5%, Vv W Resistor110000-221
R67470 Q, +5%, ¥% W Resistor110000-471
R681k, +5%, V4 W Resistor110000-102
R692.2 kQ, +5%, % W Resistor110000-222
R73220 Q, +5%, % W Resistor110000-221
R74470 Q, +5%, % W Resistor110000-471
R751kQ, +5%, % W Resistor110000-102
R762.2 kQ, +5%, V4 W Resistor110000-222
R801kQ, +5%, 4 W Resistor110000-102
R81100 2, +5%, ¥% W Resistor110000-101

(Continued on next page)

3-43

Page 70

Maintenance, Repair, and Parts Pole Position

Pole Position Video Printed-Circuit Board Assembly Parts List, continued

DesignatorDescriptionPart No.
R82-R851kQ, +5%, % W Resistor110000-102
R86220 2, +5%, V4 W Resistor110000-221
R87-R981k2 +5%, % W Resistor119000-102
Rog10 kQ, +5%, % W Resistor110000-103
R100220 2, +5%, v4 W Resistor110000221
R10110 kQ, +5%, % W Resistor110000-103
R1021.5 kQ, +5%, % W Resistor110000-152
R103-R10582.2, 5%, V4 W Resistor110000-820
1B2.2k2, +2%, 15-Element, Dual-Inline Package Resistor Pack118003-222
1K2.2 kQ, + 2%, 15-Element, Dual-Inline Package Resistor Pack118003-222

Sockets

2F28-Contact Mediumnsertion-Force Integrated Circuit Socket79-42C28
2b28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42028
2M28-Contact Medium-Insertion-Force integrated Circuit Socket79-42C28
2N24-Contact Medium-Iinsertion-Force Integrated Circuit Socket79-42024
3E, 4E24-Contact Medium-Insertion-Force integrated Circuit Socket79-42024
SF, 4F24-Contact Medium-insertion-Force Integrated Circuit Socket79-42C24
3N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
4D24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42024
5L, 6L18-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C18
6N, 7N24-Contact Medium-Insertion-Force Integrated Circuit Socket79-2024
7E28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
8N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
11N24-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C24
12J, 13028-Contact Medium-Insertion-Force (ntegrated Circuit Socket79-42C28
12K, 13K28-Contact Medium-nsertion-Force Integrated Circuit Socket79-42C28
12L, 13L28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42028
12N, 13N28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28
13H28-Contact Medium-Insertion-Force Integrated Circuit Socket79-42C28

Transistor

Q4Type-2N3904, 60 V, 1 W, NPN Transistor34-2N3904

Miscellaneous Test Points Acceptable substitute is part no. 020670-01 179051-002

Y1B24.576 MHz Crystal Acceptabie substitute is part no. 144004-002144004-003
Page 71

Pole Position

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari, Inc., Sunnyvale, CA This drawing is only conditionally issued, “and ‘neither, receipt nor possession thereof confers or transters any right in, or license to use, the subject matter ofthe drawing or any designor technical informa: tion shown thereon, nor any right to reproduce this drawing or ‘any part thereof. Except for manutaciure by vendors of Atari, inc... and for manufacture under the corporation's written license, ‘no ight to reproduce this drawing is granted or the subject mat ter thereat unless by writlen agreement with or wnitten permms- Sion from the corporation Maintenance, Repair, and Parts

24,10, 7\W|

220 [R2\, \/ew cl2 LL 470_* Tar ancig at R

Clo BBO + 35V RI, 1/2W

co + 3300nF 35V

Figure 3-18 Regulator/Audio || PCB Assembly U.S.-Built Cabinet A035435-01 G

3-45

Page 72

Maintenance, Repair, and Parts

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written dermission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any ant to reproduce tris crawing or any part thereot. Except for manufacture by vendors of Atari, Inc., and for manutacture under the corporation's written license, no right to re- Produce this drawing Is granted or the subject matter thereof unless by written agreement with or written permission from the corporation. Pole Position

24,10, 7W)

Figure 3-19 Regulator/Audio Il PCB Assembly Ireland-Built Cabinet A035435-05 A

Page 73

Pole Position Maintenance, Repair, and Parts

Regulator/Audio || PCB Assembly Parts List

Assemblies and components in the following parts list are shown in Figures 3-18 and 3-19.

DesignatorDescriptionPart No.

Capacitors

For -01* and -05** versions

C1470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
cB0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C131000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108

For -01 version

C30.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C4470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C50.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable100015-103

substitute is part no. 122005-103

cé0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C70.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C9, C103300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
Ci0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C12470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C140.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable100015-103

substitute is part no. 122005-103

C150.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122002-102
ci0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 uF, 35 V, Alutninum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
C22, C231 yF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-500105

Diodes

For -01 and -05 versions

CR1Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002
cR4Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-1N4002

Integrated Circuits

For -01 and -05 versions

QiType-LM305, 5 V, Linear Voltage Regulator37-LM305

For -01 version

QsTypeTDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
Q7Type-TDA2002A, 8 W, Linear Audio Amplifier integrated Circuit137151-002

(Continued on next page)

“Acceptable substitutes are A035435-02 or -04. **Acceptable substitutes are A035435-01, -02, or -04.

Page 74

Maintenance, Repair, and Parts

Regulator/Audio || PCB Assembly Parts List, continued Pole Position

DesignatorDescriptionPart No.

Resistors

For -01 and -05 versions

Ri270 2, +5%, % W Resistor110000-271
RS33 Q, +5%, Va W Resistor110000-330
Ra100 2, +5%, % W Resistor110000-101
R52.72, +5%, 1 W Resistor110009-027
RG3.9 kQ, + 5%, % W Resistor110000:392
R77.5 kQ, +5%, v4 W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer Acceptable19-315102

substitute is part no, 119002-102

R240.1 &, +3%, 7 W Wirewound Resistor19-100P1015
R29, R3010 2, +5%, Va W Resistor110000-100

For -01 version

RO220 Q, +5%, Ve W Resistor110001-221
R1012, +5%, % W Resistor110000-010
R1110 Q, +5%, V4 W Resistor110000-100
R12100 2, +5%, % W Resistor110000-101
R13, R1410 kQ, +5%, 4 W Resistor410000-103
R191Q, +5%, % W Resistor110000-010
R2010 2, +5%, % W Resistor110000-100
R21220 2, +5%, Ye W Resistor110001-221
R22100 2, +5%, % W Resistor110000-101
R27, R281kQ, +5%, % W Resistor110000-102

Transistors

For -01 and -05 versions

Q2Type-TIP32 PNP Power Transistor33-TIP32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055
  • Mechanical Parts

For -01 and -05 versions

J66-Position Connector Receptacle79-58306
J7@Position Connector Receptacle79-58308
Q3#6-32 x Ye-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel721608C

Machine Screw

Q2, Q3#6-32 Nut/Washer Assembly75-99516
Q2Thermally Conductive Silicon Insulator78-16014
Q3Thermally Conductive Silicon Insulator78-16008
Qs#6-32 x Y-Inch Binder-Head Nylon Screw75-F60405

Heat Sink 03453101 Test Point Acceptable substitute is part no. 020670-01 179051-001

For -01 version

J84-Position Connector Receptacle79-58354
Q8#8 x %Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc-72-6606S,

Plated-Steel Screw

Page 75

Pole Position Maintenance, Repair, and Parts

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is. only conditionally Issued, and neither receipt nor possession theteot confers o¢ transfers any right in, or license to use, the subject matter of the drawing or any design or technical inforration shown thereon, nor any right to reproduce this drawing or any part thereot, Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing ts granted or the subject matter thereo! unless by written agreement with of writlen permission from the corporation.

. Gioci

io esto | | co eco cas CO Goes e2s ence fl

Gocai GBcaz Gioc4s3 644, 470°F tebcas Ch c4Ac A70rF 21647 ,470FF Goce

Gocss cs4 "| LL L

Figure 3-20 EMI Shield PCB Assembly A037667-01 A

Page 76

Maintenance, Repair, and Parts Pole Position

EMI Shield PCB Assembly Parts List

Components in the following parts list are shown in Figure 3-20.

DesignatorDescriptionPart No.

Capacitors

C1-C50.1 uF, +80, -20%, 50 V Ceramic-Disk RadialLead Capacitor122002-104
C6-C100.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C120.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C13-C150.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C160.01 uF, + 80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C17-C240.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C250.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C27-C310.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
32,0330.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C34-C390.01 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor122005-103
C40-C430.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C440.471 uF, + 80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-471
C450.001 pF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-102
C46,C470.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor122016-471
C480.1 wF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104
C54,C550.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor122002-104

Connectors

P1930-Pin Card-Edge Connector179046-030
P2044-Pin Card-Edge Connector179046-044

3-50

Page 77

Pole Position Maintenance, Repair, and Parts

H. Power Supply Assembly

WARNING A03588-01 Fuse cover must be in place dur- (Transformer assy.) ing game operation.

A021084-xx (Voltage plugs)

29-053 (Capacitor) i 034544.01 U (Fuse block cover)

79-4411001 (Fuse post) 78-70501SC (Capacitor bracket) ! 5 mL 46-2017002 (Fuse)

29.053 {Capacitor ‘A035891-02 . 034482.02 5 : (Chassis) (Fuse harness assy.)

46-301203

78-2708 (Bushing)

A034630-01 (Filter Assy.) (Fuse block) 78-70801SC ee ¢ 46-2014002 (Bracket) (Fuses)

A035890-01 79-15021001 (Power harness) (Terminal block)

oierritd (AC harness)

Figure 3-21 Power Supply Assembly A037671-04 &-05 G

3-51

Page 78

Maintenance, Repair, and Parts Pole Position

Power Supply Assembly Parts List

Assemblies and components in this parts list are shown in Figure 3-21.

Part No. Description (Reference Designations in Bold)

A021084-01Voltage Plug for 100V (90-110 VAC)(violet)
A021084-02Voltage Plug for 120V(105-135 VAC)(yellow)
A021084-04Voltage Plug for 220V(200-240 VAC)(biue)
A021084-05Voltage Plug for 240V (220-260 VAC)(brown)

A034629-01 AC Harness Assembly

A034630-01RFI Filter Assembly(FL1—designation not marked)

A035888-01 Upright and Cabaret Transformer Assembly (T1) Acceptable substitute is part no. A035888-02 A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6) 29-053 27,000 uF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140024A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F2, F4-F6)
46-201 70027 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30125325 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %,-Inch Outside Diameter x %-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket (C1)

79-150210012-Circuit Single-Row Terminal Biock(located under F4)

79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 03448202 Power Supply Chassis

034544-01Fuse Block Cover(F2-F6)
037639-03, -04Label tor Fuse Value(F1)
037641-01Label for Fuse Values(F2-F6)

A037671-04 power supply has the 120 V plug. ‘A037671-05 has the 100 V, 220 V and 240 V plugs. A037671-06 has the 220 V and 240 V plugs.

3-52

Page 79

Pole Position

Glossary of Terms

AC Alternating current; from zero li rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (@.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as a 1 or ad. BLANKING Turning off the beam on a cathoderay tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations, CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass.

CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice.

CLOCK A repetitive timing signal for synchronizing system functions.

COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electro-mechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circultry. Glossary

COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. pc Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electro-magnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors, DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage.

GLt

Page 80

Glossary

GATE

  • A circuit with one output that responds when and only when a ceriain combination of pulses is present at the inputs.
  • A circuit in which one signat switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube. Life) Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on ihe program, the processor may or may not respond. LED The abbreviation for a light-emitting diode, LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circult during a particular time, Also called the lagic level. The list below shows the voltage levels corresponding to the logic states (levels) ina TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +08 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several lowspeed inputs and combines them into one high-speed data stream for si-

nuttaneous transmission on a single

ine.

GL2 NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathoderay tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit Pole Position

streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR Aline segment drawn between specific X and Y coordinates ona cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. XY DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 81

Pole Position 2nd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

lf you have any technical questions about certain ATARI games producis, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm CO Distributor

Address. CJ Operator City State Zip C Other.

Area Code Phone

Page 82

First fold

No Postage Necessary if mailed in the United States

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA POSTAGE WILL BE PAID BY ADDRESSEE

Attn.: Field ServicefCoin-Op Division i P. O. Box 427 Pe a a Atari, Inc. Pe

Pe Sunnyvale, California 94086 Pe a a

Second fold

WO aBpe siyy ede, 4

Page 83

Pole Position 2nd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name.

Firm U Distributor

Address OC Operator City State Zip U Other

City State Zip U Other.

Area Code Phone

Page 84

First fold

Attach Necessary Postage

Atari Ireland Limited Attn.: Field Service/Coin-Op Division i Tipperary Town, Ireland

Second fold

WuOd 4 eBpe sy) edey

Page 85

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 86

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 87

SO RE GE eS

a >

SESS SS EASES

Warranty

Seller warrants thal its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

\f the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits. loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. x © % * © © © = AN

Page 88

TH

ATARI, INC. 790 SYCAMORE DRIVE P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 * TELEX 35-7488