Pot of Gold
Leprechaun (set 1) (Pacific Polytechnical Corp., 1982) · Manual · 34 pages · 24 sections · original scan
GAME PLAN. INC \ 1515 W Fullerton Avenue Addison. tHlinois 60101 Telephone (312) 628-8200 TUX 20-6098 £ Zs
WARNING
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. As temporarily
permitted by regulation it has not been tested for compliance [with the
limits for Class A computing devices] pursuant to Subpart J of Part 15
of FCC Rules, which are designed to provide reasonable protection
against such interference. Operation of this equipment in a residential
area is likely to cause interference in which case the user, at his own
expense, will be required to take whatever measures may be required to
correct the interference.
1.0 INTRODUCTION
POT-OF-GOLD is a 19" full color, one or two player game that will
capture and prolong player interest, as well as provide a constant challange.
It has a joystick control for the sleuth movement,
To allow the player to move the sleuth to intercept the POT-OF-GOLD
1.1 UNPACKING INSPECTION
To ensure the equipment incurred no damage in shipment, inspect
the container prior to acceptance from the carrier. If no immediate
cabinet damage is evident, perform the following visual inspection:
- Open the rear of the game with the appropriate packaged key.
2, Examine each major and electrical component throughly for scrapes, broken or missing parts and loose or missing screws.
- Check for loose cable connectors.
- Wisually verify that all the integrated circuit devices (IC's) plugged into sockets are properly seated and that no IC pins are bent or misaligned.
Tf you find any damage during this inspection, file a claim with the freight carrier, and send a complete report of the damage to
GAME PLAN, INC.
1.2 INSTALLATION
Planning the location of the game should involve both physical and
electrical consideration, Physical considerations concern the placement of the equipment with respect to clearances, AC cable and eviromental conditions
such as ventilation, temperature, weight support and accessibility (although
your game has the durability to endure mearly every type of physical hazard).
Electrical considerations include availability of the correct voltage and
frequency.
In planning this installation, consideration must also be given to working
space required for personnel involved with operation or maintenance of this
system.
A.
B.
1. Install 4 provided levelers to bottom of cabinet and level cabinet.
The power is controlled by a switch located on top of the cabinet plug into A.C. only 115 volt 60 cycle.
Do not install this game in places directly exposed to sunlight of excessive heat, to prevent rising internal temperatures.
High voltage runs the monitor. Therefore only persons familiar with safety measures should make any adjustments.
As with any solid state games the power should be turned off before replacing any parts or disconnecting any plugs.
Always take boards to distributor for repair, do not attempt to make any repairs with volt-ohmmeter or other test equipment as the internal voltage of such equipment may damage the circuitry.
1.3 PRELIMINARY CHECKOUT PROCEDURE
After properly installing POT-OF-GOLD we suggest checking it's operation in following procedure:
1,
2.
3. Plug the AC jack into the AC outlet. Allow one to two minutes for CRT to warm up.
Observe the TV monitor display to assure the correct attract mode is present on the screen, as explained in Section 2,2.
If the POT-OF-GOLD display is incorrect, correct immediately.
Insert a quarter into the coin slot.
Continue to play the game and verify that all screen images are displayed, once again, discribed in the Normal Operation procedure.
repairs are necessary, contact your distributor or GAME PLAN, INC.
0 GAME DESCRIPTION
The following paragraphs describe the video images, sound effects,
game strategy.
2.1 RESET MODE ATTRACT MODE
Whenever power is applied, the game will start to sequence thru the
attract mode.
1, POT-OF-GOLD
. LEPRECHAUN LORE (w/score dispiayed)
- TREE SCORES (w/score displayed.
SIMULATED GAME PLAY(sequenced through forests but without naming forests. =
- POT-OF-GOLD HALL OF FAME (high scores since last power-up)
This sound alerts the operator, it will even serve to discourage
tampering by its psychological effect.
2.2 COIN INPUT MODE
At all times, while power is on, regardless of the game conditions or
the operator options, the computer will accept a coin input, generate
a unique sound, and increment the coin counter. However, the credits will
only be incremented if they are not already at the maximum (10,20,30, or 40-operator selectable) and they will be displayed only during the attract modes.
2.3 GAME START MODE
The computer scans the game-start switches only during the attract and
game over modes and only then if the credit-count is not zero. When a start switch is activated, the computer compares the operator selected credit option
against the credit-count and ignores the switch if enough credits are not
available. If there are sufficient credits, the computer subtracts the price of
the selected game, resets the player scores to zero, generates the game-in
play (GIP) sound, and displays the GIP message.
2.4 GAME START MODE The game~play sequence in POT-OF-GOLD consists of 3 or 4 turns (operator selectable) each of which lasts as long as the player can skillfully maneuver his
sleuth to avoid the Leprechaun, while attempting to touch the POT-OF-GOLD.
Also touching trees will increase the pots value and increase the players score.
but the players score will not.
2.4 SINGLE PLAYER GAME CON'T
When the player loses a man by being caught by the Leprechaun, the G.I.P message reappears (stating whose turn it is, which forest it is
by name, and how many sleuths are left. After the last man is lost the game-over
message is displayed.
Assuming a 3 man game, game play begins with the message player 1 up, somewhere in the forest of KELLS, and 3 sleuths displayed, then the forest
will appear, complete with Leprechaun, and POT-OF-COLD, then the sleuth will appear-it should be noted that the sleuth and the Leprechaun always appear
in the same place, while the POT-OF-GOLD is placed randomly in the forest. The Leprechaun will try to ;catch you and keep you from hitting trees or
getting the pot. The player uses his joysitck control to move his sleuth through the forest, hitting as many of the various trees, because for every tree the
sleuth hits, the value of the pot increases, as well as the players score
increases.
Whenever a sleuth hits a tree a distinctive sound is heard and his score
and the pots value is increased. When the sleuth gets close to the pot, the
Leprechaun will abandon chasing the sleuth and attempt to beat the sleuth to
the pot in order to move it to a different position. During this time the
sleuth is immune from being destroyed by the Leprechaun. When the sleuth
touches the pot, a different distinctive sound is heard, and the sleuth
dives into the pot causing the gold to overflow, and the players score to
increase,After the players score is increased the G.I.P message re-appears
stating player l-up somewhere in the forest of CONNEMARA and the total number of sleuths left .When the sleuth is finally caught by the Leprechaun the man
and Leprechaun will disappear, the trees will change back to their original color
and the G.I.P message will reappear stating player l-up somewhere in the forest of (the same forest where the sleuth was just caught) and all trees
in their original color.
The pot starts with a value of 1000 pts. and is increased by 500 pts
each succeeding forest to a max of 7500 pts.
Forest name KELLS, forest #1,9,17, etc. Forest name CONNEMARA forest #2,10,18, etc. Forest name CORK forest # 3,11,19, etc. Forest name LIMERICK forest # 4,12,20, etc. Forest name MUNSTER forest # 5,13,21, etc. Forest name DINGLE forest # 6,14,22, etc. Forest name DONEGAL forest #7,15,23, etc. Forest name TRALEE forest #8,16,24, etc.
2.4 SINGLE PLAYER GAME CON'T
In addition after every 4th screen there is a display depicting the sleuth
walking down the rainbow into a POT-OF-GOLD. im every forest the Leprechaun is slightly faster then in the previous forest, also the speed of the Leprechaun is updated every 30 sec. (approx) during each forest, to prevent a player from only skillfully evading the Leprechaun and only hitting trees and thereby greatly increasing game played time.
2.5 TWO-PLAYER MODE
The play of POT-OF-GOLD in a two-player game is identical to single-play with the players alternating turns. On the Upright version, the players use one common set of control. On the cocktail version there are two sets of controls on opposite sides of the table. The computer activates control alternately
between 1 and 2 and flip-flops the screen image so that it is oriented to the player in control. :
The G.1.P message, which appears after each turn, clearly indicates which player is up,this allows time for the players to pesition themselves at the controls, but is brief enough to avoid unnecessary "dead-time".
After the players have lost their last sleuth the game-over message will be displayed. At that time the computer will scan the players score along with the existing score, should the players score be high enough to be listed a screen will be displayed explaining the method used to enter the players initials (3 max.), after this is done the POG HALL of FAME is
displayed showing where the players score is ranked since the last interruption of power,
3.0 COMPUTER SYSTEM
The Computer System consists of 2 printed circuit assemblies which perform the functions illustrated in Figure I. A self-contained switching regulated power supply provides reliable DC voltages to enhance the overall computer system reliability.
The Game Computer Board controls the game sequence, image generation, system-level diagnostics (accessed by test - EPROM and switch) audio and peripheral interface; thus keeping interconnections to a minimum.
The Video Computer Board contains the display RAM and timing circuits to interface with any standard RGB raster-scan color monitor. The Video Computer also contains unique input timing circuits which permit vector graphic writing to the video RAM.
3.1 POWER. SUPPLY
The computer system power is provided by a high efficiency, very reliable, switching-regulated, power supply. It eliminates the hot, bulky transformers required by old-fashioned supplies and the high efficiency permits it to run cool at extreme of input line voltage variations,
The computer system uses -5, +5, and +12 VDC. The primary power is +5 VDC for the TIL and MOS devices. The ROM's can be either triple-voltage or single-voltage. The dynamic video RAM's use all 3 voltages. The audio amplifier uses +12 VDC. The coin door lamps and meters use +5 VDC.
DC voltage distribution form the power supply to the four circuit boards is multiply-redundant to enhance reliability. Each voltage is carried by two wires to each board. All four power connectors are identical, are keyed, and are symmetrical, so that only intentional abuse could result in faulty power connections. Each of the three voltages is current-limited by the supply to provide protection against short-circuits.
GAME
COMPUTER
POWER SUPPLY +5 VDC -5 voc +12 VDC VIDEO
COMPUTER
CONTROLS SPEAKER MONITOR
FIG - I
GAME BLOCK DIAGRAM
3.2 GAME COMPUTER
The Game Computer uses a 6502 central processor in a conventional computer architecture containing ROM, RAM, and I/O ports (FIG. 2). The computer clock uses a standard 4.00 megahertz crystal which is divided by 4 to provide a CPU clock of 1 megahertz.
The computer contains a unique power-on reset circuit which requires a positive feedback response from the computer to disable the reset circuit. Therefore, an initial power~on software program must successfully complete a specific set of operations or else the circuit continuousiy resets the computer. This technique assures that the computer is operating properly before continuing but does not require the software overhead of "watchdog" circuits.
Conventional TTL address decoding generates signals to select one of eight (8) ROM's or two (2) RAM's. Program and image storage is provided by eight (8) -4K x 3 - 2732 E PROM's. Computer scratch-pad RAM is either two (2) | K x 4 - 2114's or two (2) 256 x 4 - 2101's.
Port 1 provides an 8-Bit video data byte on port 1A and a 4-Bit video contro] address on Port 1B to write data into the video RAM. In addition, port 2B receives video timing signals which are used to synchronize the game program with the video display.
Interface Portion uses port 2A and 2B to create a 6 x 8 switch matrix for scanning up to 48 switches. Two (2) columns of the matrix are used to scan two 8-position DIP switches providing operator options. The remaining switches provide signals for driving coin meters and other peripheral devices. in addition, Port 2 is linked to the power-on reset circuit so that the computer can enable or disable the reset signal.
Audio Section of the board transmits game sounds thru Port 3.
CLOCK x 1K x 8
CIRCUIT RAM
. (Optional)
ADDRESS
DECODE
CENTRAL
PROCESSOR
BUSS CONTROL
BLOCK DIAGRAM COMPUTER BOARD FIG. BUFFER
AUDIO INTERFACE RESET PORTION PORTION CIRCUIT (Port 3) (Port 2)
3.2.2 - FIG4 3.2.1 - FIG3
OPTION SWS
VIDRO COMPUTER (FIG 5)
3.2.1 PERIPHERAL INTERFACE PORTION
The Peripheral Interface Portion provides buffers and drivers for protective isolation of the electronics. Up to 32 switches can be handled by 4 columns of a switch matrix, as illustrated in figure 3. Each switch is "diode-isolated" to provide "n-key rollover", The potential problems of ghost~ switches is also eliminated by putting all critical, non-player-accessable switches in a single column.
CcOL.A
COIN DOOR
COL.B.
GAME START
COL.C.
PLAYER 2 3 | aq < iso ° |
coL.D | | PLAYER 2
|PERIPHERAL | ) INTERFACE pponaney (3.2.1) |
°
Q oO g =z
Q Sc Oo wm
FIG. .3
PERIPHERAL INTERFACE (BLOCK DIAGRAM)
AUDIO COMPUTER
The Audio Computer also uses a 6502 central processor chip as illustrated in figure 4 and it also uses a standard TV color-burst crystal to generate a computer clock slightly less than 900 kilohertz. However, Port 5 uses a 6532 which provides dual 8-Bit bi-directional data-bus buffers plus 128 bytes of RAM. Program storage is provided by a single 2K x 8, 2716 EPROM or 2316 ROM,
The small amount of RAM and ROM is sufficient for this system because of the use of a unique programmable sound generator chip (AY-3-8910 PSG). This device contains 3 sets of tone generators, a pseudo-noise generator, and 3 channels with a variety of amplitude controls-all under stored~program control. in addition, the PSG contains two 8-Bit ports which are used to read two DIP switches that can be used to manually program the PSG for test purposes.
Access to the Audio Computer is through Port 5A which interrupts the processor when a sound-request is made. The computer stores the sound request data-byte and then re-transmits it on Port 5B. Thus the Game Computer can verify that a requested sound has been processed and, if this verification is not received, force a reset of the Audio Computer.
The 3 audio channel outputs of the PSG are amplified by an industrystandard, reliable LM 380. The amplifier operates with regulated 12 VDC which provides sufficient audio volume for noisy arcades, and yet is only 60% of the rated voltage to provide another margin of reliability.
A volume control is located on the Computer Board. Individual game sound volumes are programmed to balance the overall audio effect.
Pr AUDIO
CIRCUIT
GENERATER
ADDRESS
DECODE
ADDRESS |
(PSG)
CENTRAL
PROCESSOR
AUDIO coc oor >
PORTION (3.2.2)
AUDIO COMPUTER (BLOCK DIAGRAM) FIG.
3.3 VIDEO COMPUTER The Video System uses a RAM intensive, dot-oriented technique. What this means is that the circnit board contains sufficient memor) to store am entire CRT screen image and that each bit in this RAM array can be individually addressed.
The large memory array is comprised of low-cost MOS dynamic RAM's which are ideally suited for video display. The repetitive reading of the memory for raster sean display automatically takes care of the refresh timing required to retain dynamic memory. On the other hand, dynamic RAM's are notoriously unreliable (by digital computer standards) but occasional bit errors are tolerable (in fact, often invisible) on a CRT screen. Some systems use part of the video RAM for computer scratch-pad but the video computer apperar to the game computer as a "“write-only" devise.
As illustrated in figure §, the Video Computer contains 3 seperate RAM arrays for each of the 3 spectral primary colors; red, green, and blue. Two independent sets of counters generate read and write addresses that access the 3 arrays in parallel to generate color dots (pixels). The read-address counters perform the dual function fo generating horizontal and vertical timing signals for synchronization of the CRT monitor and the Game Computer image generation.
The write-address counters are parallel-load, up,-down devices which provide 2 modes of writing to the display memory. In the first mode, the write-counters can be loaded with a 8-bit X-address and an 8~bit Y-address to locate the bigining of a line bector. The second mode involves incrementing or decrementing the counters to move the write-address along a desired vector. Each time a writeaddress is changed, the Video Computer automatically writes the specified color bits into that RAM location.
A Write-request to the Video computer is no-synchronous so timing buffers interface the read and write functions. In addition, the timing buffers generate "wait" signals to let the Game Computer know when each write operation is completed.
The 8-bit X-Y addressing generates a 256 x 256 screen image (256 dots per line and 256 lines per game screen. This symmetrical display combined with the vector graphic writing technique provides simple software control of the screen image orientation. Thus the system provides switch selection to use vertical or horizontal monitors, inverted screen for cocktail flipflop of 2-player games, and reversed images for mirrored games.
CLOCK
CIRCUIT
VIDEO
READ
ADDRESS
CONTROL
SYNC & BLANK CIRCUITS SYNC & BLANKING OUTPUTS
RAM
DECODE
TIMING BUFFERS
RED GREEN VIDEO VIDEO 4K x 16 4K x 16 D RAM | D RAM WRITE ADDRESS CONTROL MULTIPLEX
WRITE
COUNTER WRITE DELAY OUTPUTS
DATA BUS WRITE
DECODE
BLUE
4K x 16
VIDEO COMPUTER (BLOCK DIAGRAM) FIG. § INPUT FROM GAME COMPUTER CONTROL BNS
GamePlan, inc.
February 17, 1982
DIP SWITCH SETTINGS FOR POT-OF-GOLD
BONUS SLEUTH NO BONUS BONUS MAN @ 30,000 BONUS MAN @ 60,000 BONUS MAN @ 90,000
NUMBER OF SLEUTH
ATTRACT MODE SOUND DSB:
BONUS SLEUTH 12 swS 1 & 2 Oo 0 c¢ 0 oc c Cc
NUMBER OF SLEUTH @ START 3 sw 3 fe) c
SOUND DURING ATTRACT MODE 4 sw 4 ie} c
SWITCHES 5, 6, 7 & 8 NOT USED SOUND OFF SOUND ON
GAME PLAN. INC 1515 W Fullerton Avenue Addison. Illinois 60104 GamePlan, inc. Telephone (312) 628-8200 TLX 20-6038,
February 17, 1982
DIP SWITCH SETTINGS FOR POT-OF-GOLD
DSA:
COIN CHUTE NO. 1 (SWS 1 & 2) CREDITS/COIN 1 2 0.60 Cc Oo oc coc
COIN CHUTE NO. 2 3.4 CREDITS/COIN
| (SWS 3 & 4) | Ca) | 1 | i |
| c Oo | 5 | 1 | |
| oc | 6 | 1 | |
| cc | 7 | 1 |
MAX CREDITS 56 MAX CREDITS
| (SWS 5 & 6) | 0.0 | 10 |
c Oo 20 oc 30 coc 40
FREE PLAY 5W7 (SW7) 0 NORMAL, c FREE PLAY
COCKTAIL/UPRIGHT (sw8) 8 GAME STYLE ie} | UPRIGHT
Cc COCKTAIL
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ieaeng Nonber AZ-TOOEIS
Cow Door
Lames Cow
COUNTER,
NOTE:
ON UPRIGHT GAME, PLAYER. | 22 OW/TCHES ARE COMMON
AND ARE BOTH WIRED TOTS — J4 USED OF COCKTAIL TABLE ONL
COIN DOOR. GAME CONTROL
SWITCHES OW/TCHES PLAYER. Z SWITCHES ie caos A GAME PLAN Ine. z t F
Pants must BE CLEAN
AND FREE OF BURRS
[prauina Nomber 02-7008)
PERIPHERAL INTERFA
cu BOAZO
XTAL
- SR ANZ
Ag
2] zi aL SOT ti2v on Rilo
ADDRESS Bus
ADD JUMPER WIRE '
if
!
- | a7 0 C1 Rie >>d7B DaswBD Req dan~s
Qe Sg
13 2 uo G4x 710K | pecooe é a nfoas
VERT. BLAWK VIB we
vee VIB A) VIB AZ
= le Sa TEE rise ceeaR DELAY = non’. BLANK RECET DISABLE ware OFLAY
' GND vee cys TEM RESET oD = F = vif iow svc FOY mE —T I’ cara Mee
osed Juk ygo0 WP ig te ies A INDICATES CHANGES TO EXISTING BOARDS, FOR USE AS KAOS HARDWARE
CooCoyEwerera SAME PLAN The. KAO$ ‘Ss W. Fullerton Ave PARTS must 8 coEan IND FREE OF sures
POWER (N
+5 Gwe “5 <5 Gno 5s te no. Nic. Roly OPTION. TMS gra er 2716 SAA, JOOMF as Mr oN 2525 vey PID Re = ice Vo gig P20
- -5v_ Pa
Soe eS #
ED
S fre uz P83] ge ra ac © O7 4 (\ 0:
TH 1
1 4 RESET
ala loll vlolsly ato 34Fw SPARSE SI PSS Biss nest ‘AV ELL Hy s}ysystel4|e]5|7, aur Fron sors ® ig - CE lens 8 g A $ 3 AULIOC AMPLIF ITER, Ale caps NMP Ow LOK Abe RESISTORS +59 9 M4 VAT
ISSUE PARTS MUST BE CLEAN Ano FREE OF BURRS [Stole GAME PLAN Ine. 1815 W. Fullerton Ave Addison ILL. 60101 Yo Pree Dore 2 ppc) [AR
+ 018} AUB COMPUTER BoaeD Bel Auoig AMPLIFIER
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
MONITOR
SERVICE INSTRUCTIONS
02-30073
K4600 IMPORTANT SERVICE SAFETY INFORMATION
X-RAY RADIATION WARNING NOTICE
PRODUCT SAFETY NOTICE
AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L’APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.
For replacement purposes, use the same type or specified type of wire and cabie, ensuring that the positioning of the wires is followed (especially for H.V. and power supply circuits). Use of alternative wiring or positioning could result in damage to the monitor or in a shock or fire hazard. The picture tube used, employs integral implosion protection and should be replaced with a tube of the same type number for continued safety. When handling the CRT, shatter-proof goggles must be worn after completely discharging the high voltage circuit. Do not lift the picture tube by the neck.
PERFORMANCE AND OPERATING DATA
- Apply a suitable power source to the monitor through an isolation transformer.
- Apply a suitable signal source to the monitor PCB by means of P205.
- Set up Controls. All controls are preset at the factory, but may be adjusted to suit program material.
1.0 Supply
Voltage 108 VAC - 132 VAC
Frequency 50 Hz- 60 Hz
2.0 High Voltage (EHT)
For 19"V models 25.5 + 0.8 K.V. atO0 Beam
- Service Set-Up Controls
G. Screen Control = VR406 H. Video Drive Controls - Red Drive = VR401 Green Drive = VR402 |. CRT Cut Off Controls - Red Cutoff = VR403 Green Cutoff = VR404 Blue Cutoff = VR405
SERVICE INSTRUCTIONS A.V. Adjustment VR501 set for 127V DC B. Vertical Size Cont = VR302 C. Vertical Hold Cont = VR301 D. Horizontal Hold Cont = VR351 E. Horizontal Width Cont = L702
F. Focus Control = VR702
FOCUS Adjust the Focus control (VR702), tocated on the HV unit (7701), for maximum over-all definition and fine picture detail.
+127V ADJUSTMENT (See Fig. 1) The + 127V adj. contro) (VR501) is adjusted at the factory. However, if readjustment should be required, proceed as follows.
- Operate monitor for at least 15 minutes at 120V AC tine.
- Connect Positive lead of V.T.V.M. to blue lead of TR502 negative lead to chassis ground.
- Adjust VR501 to obtain + 127V reading.
- After adjustment VR501 must be locked with a sealing varnish.
VRBO! +8 Adj
Seal or Lock
TR502 Emitter
Chassis Ground
FIGURE 1 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention. If however when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished). VERTICAL SIZE (HEIGHT) The vertical height control is a screw-driver adjustment. Location of this control is shown in Fig. 3. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions. Hangto Cabinet CIRCUIT PROTECTION A3.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.
HORIZONTAL OSC. ALIGNMENT (See Fig. 2) A warm-up period of at least five minutes should be allowed before alignment is carried out. Set VR351 to center position. Adjust 1351 after grounding R328 plug. (TP32 of Vert/Horiz. P.C. Board) through a 1uF/50V capacitor. Adjust L351 to obtain normal picture. After adjustment, remove 1uF/50V capacitor.
5OV/1F + Chassis Ground R328 (6P Plug for PC Board Side) TP32
L351
FIGURE 2
Heat Sink Ass y Audio/Power (MV-3)
Vert/Horz Board (QJ-2) Service Tip (5) r= Service Tip (N VR402 Blue Drive Control ae Red Drive Controt VR405 Blue Cut Off Control VR404 Green Cut
- Off Control /\—vp40o3 Red Cut Off Control P.C. Board Holder
V Hold) VR302V Su R351 VRA406 Screen Contro! Neck Board (QG- 1) H Hold
FIGURE 3
- MAIN P.C. BOARD|MQ-29 P.C. BOARD LAYOUT
P.C. BOARD LAYOUT
NECK P.C. BOARD |MS/QG
POWER PC BOARD[MV
P.C. BOARD LAYOUT
HORIZ/VERT P.C. BOARD| MT/QJ
REPLACEMENT PARTS LIST
A & SAFETY CRITICAL PARTS LIST This receiver contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or Axe on parts list should be replaced with exact factory re- Placement parts. The use of substitute parts may create a shock, fire, x-radiation or other hazard. Service should be performed by qualified personnel only MAIN BOARD (MQ-29)
| Ref. No. | Part No. | Description | Ref. No. | Part No. | Description |
RESISTORS CAPACITORS
| R603 | 340x3334-944 | 330k Ohm, + 10%, 1/2W Carbon | — AC601 | 203X1800-451 | 0.1. uF, 125V, +20% MM | ||
| R605 | 203X9014-584 | 4k Ohm, | 5%, WMO. | C602 | 80X0096-038 | 2200 pF, * 10%, Z5F | |
| GOB | 204X1425.021 | 470 Ohm, + 10%, 5W W.W. | C603 | 202X7810-214 | 2200 pF, 125V Ceramic | ||
| A% R607 | 204x 1450-508, | 2.7k Ohm, + 10%, SW W.W. | ©604 | 80X0096-038 | 2200 pF, + 10%, Z5F | ||
| 7608 | 203X8014-603 | 4.2k Ohm, £5%, 1W MO. | 608 | 203X0220.043 | 300 uF, 200V Electrolytic | ||
| 7610 | 203X6500-246 | 22 0hm, 5%, 1/8W Carbon | C605 | 203X 1205-165 | (0088 UF, 600V, + 10% PP | ||
| R611 | 203X6700-562 | 4k Ohm, + 5%, 1/2W Caibon | ceo? | 203x0040-020 | 10 uF, 160V Electrolytic | ||
| R612 | 340X3471-944 | 470 Ohm, + 10%, 1/2W Carbon | C608 | 203X0040-052 | 47 uF, 160V Electrolytic | ||
| R613 | 203X9010-787 | 4.2k Ohm, 5%, 1W M.O. | C609 | 202X7050-366, | 0033 uF. S00V, + 10% Ceramic | ||
| R614 | 203x5202-320 | 680k Ohm, £5%, 1/2W Comp. | 610 | 202X7050-483 | “01 uF, 500V, + 10% Ceramic | ||
| R615 | 203X5602-156 | 270k Ohm, +5%, 1/2W Comp | cent | 202X8140-022 | 400 pF, 3KV, + 10% Ceramic | ||
| R616 | 203X6500-741 | 2.7k Ohm, +5%, 1/8W Carbon | 612 | 203x 1201-047 | .022 uF, 200V, + 10% PP | ||
| R617 | 203X6501-088 | 68k Ohm, 5%, 1/8W Carbon | C613 | 203X0015.035 | 220 uF, 25V Electrolytic | ||
| 620 | 203X6500-508 | 270 Ohm, +5%, V/8W Carbon | ce14 | 203x0015-006 | 33 uF, 25V Electrolytic | ||
| R622 | 203X6500-689 | 4.5k Ohm, 6%, 1/8W Carbon | C615 | 203X 1201-288 | 0.39 uF, 200V, + 10% PP | ||
| R624 | 203X6205-843 | 1k Ohm, +5%, 1/2W Carbon | C616 | 2028065-499 | 47 pF, 500V Ceramic | ||
| R630 | 203%5601-906 | 68k Ohm, +5%, 1/2W Carbon | ce17, | 203x0025-019 | 1 uF, SOV Electrolytic | ||
| R631 | 203X9015.087 | 2.2 Ohm, + 10%, 5W M.O. | ces | 202X8000-577 | 82 pF, SOV, + 5% Ceramic | ||
| R632 | 340X8121-731 | 120 Ohm, + 5%, SW Carbon | ce19 | 203X0025-019 | 1 uF, 50V Electrolytic | ||
| R634 | 203X6000-002 | 2.2 Ohm, | 5%, 1/8W Catbon | 620 | 203X1107038 | 0.1 UF, 100V, * 10% Mylar | |
| R635 | 340X3682-944 | 6.8k Ohm, = 5%, 1/2W Carbon | C621 | 202X9040-155 | > | —=—=«O.1. uF, 1.5KV, + 20% Paper | |
| R636 | 203X6500-645 | 1k Ohm, +5%, 1/8W Carbon | C622 | 203X0020-099 | 1000 uF, 35V Electrolytic | ||
| R640 | 203K6500-762 | 3.3k Ohm, 5%, 1/8W Carbon | C623 | 203X0015.053 | 470 uF, 25V Electrolytic | ||
| R641 | 203X6501.002 | 33k Ohm, 5%, /8W Carbon | C624 | 203X0015-021 | 100 uF, 25V Electrolytic | ||
| Red2 | 203x6500-927 | 45k Ohm, *5%, 1/8W Carbon | 625 | 203x0040-020 | 10 uF, 160V Electrolytic | ||
| R643 | 203X5602648 | 3.M Ohm, 5%, 1/2W Comp. | C626 | 202X7050-009 | 100 pF. 500V, + 10% Ceramic | ||
| R646 | 203X6500-468 | 180 Ohm, +5%, 1/8W Carbon | 627 | 202X8065-461 | 39 pF, 500V, + 10% Ceramic | ||
| R647 | 340X5150-841 | 15 Ohm, + 10%, 2W Carbon | C628 | 202X7000-327 | 2200 pF, 50V, * 10% Ceramic | ||
| R648 | 340X2225-934 | 2.2M Ohm +5%, 1i4W Carbon | * 629 | 203X1270-470 | 6900 pF, 1.5KV, + 5% PP | ||
| R649 | 340X3182-944 | 1.8k Ohm, + 10%, 1/2W Carbon | C630 | 202X7810-214 | 2200, pF, 125V Ceramic | ||
| R650 | 340X327 1-944 | 270 Ohm, + 10%, 1/2W Carbon | ce32 | 203X0005-029 | 470 uF, 6.3V Electrolytic | ||
| RESt | 340X5241-743 | 240 Ohm, | 10%, | 2W Carbon | C633 | 203X0315-033 | 2.2 uF, SOV Electrolytic |
| R652 | 340X3682-244 | 6.8k Ohm, + 10%, 1/2W Carbon | C634 | 202x8000-164 | 6 pF, S0V, | 0.5 pF Ceramic | |
| C637 | 202X8105-014 | 3 pF, 2KV, + 0.5 pF Ceramic | |||||
| C638 | 342X5632-040 | 056 uF, 10% Mylar |
SEMICONDUCTORS
| TREO1 | 200X3189-304 | Transistor, 2561893 |
| X601 | 201X3130-109 | Rectifier, (SI) RM-2AV 600V |
| x602 | 66x0023-009 | Rectifier, Power (S1) 500V PIV |
| x603 | 66X0023.009 | Rectifier, Power (S1} 500V PIV |
| x604 | 66X0023.009 | Rectifier, Power (S1) 500V PIV |
| x605 | 200X8130-171 | Diode (HS) SB-2CGL 1200V min. |
| x608 | 201X2010-144 | Diode (Sl) 182473-772 |
7 201X2100-119 Diode (HS) RC-2V 0.8 US.
| pied | 201X2130-234 | Diode (HS) RU-2V | MISCELLANEOUS |
201X2130-234 Diode (HS) RU-2V -
| X610 | 66X0023-009 | Rectifier, Power (SI) 500V PIV | ae | 207 120.082 | Loatihi ucsa) 3-125 | |
| x611 | 66X0023-009 | Rectifier, Power (SI) 500V PIV | P602 | 204x9800-260 | Plug 3 Pin | (eT) |
| x612 | 66X0023.009 | Rectifier, Power (S1) 500V PIV | oe | Pin | ||
| P603 | 204x9600-254 | Plug, 3 Pin (NM) | ||||
| P604 | 204X9600-298 | Plug, 4 Pin (NM) | ||||
| P606 | 204X9600-351 | Plug, 6 Pin (NM) | ||||
| TRANSFORMERS & COILS | 607 | 204X9600-380 | Plug, 6 Pin (GT) | |||
| 4.1601 | 201x6000-112 | Coit, Line Filter R-3 | Head | perenne | ria eee. | |
| L602 | 201X4600.042 | Coll, Filter, 10 uH | P61 | 04x9800670 | Plug, 2 Pin (NM) | |
| L603 | 201X4100-024 | Coil, Peaking, 22 uH | THeOt | soixot-004 | Thenmistor | |
| L607 | 201X4710-134 | Coil, P-F Choke | TH602 | 201X022-007 | Varistor | |
| T601 | 201X9500-337 | Transformer, Audio Output | 03 | 306X8019-207 | Socker 4 Pin | |
| 7602 | 201X1300-080 | Transformer, Hor. Drive | P201 | 204X9601.195 | Plug, 6 Pin | |
| 7603 | 202X1210-191 | Transformer, Side PC | 202 | 204x9601.195 | Plug, 6 Pin | |
| L702 | 9A2795.001 | Width Coil | : |
VERT/HOR BOARD (MT/QJ)
| Ref. No. | PartNo. | scr | Ret. No. | Part No. | Description |
RESISTORS CAPACITORS (CONT.)
| R301 | 203x6500-628, | 820 Ohm, + 5%, 1/8W Carbon | 0913 | 203x0025-087 | 47 uF, 50V Electrolytic | |
| R302 | 203x6500-902 | 12k Ohm, + 5%, 1/8W Carbon | 6315 | 203X0015-082 | 10 uF, 25V Electrolytic | |
| R303 | 203X6500-927 | 15k Ohm, = 5%, 1/8W Carbon | C316 | 203X 1100-220 | 3300 uF, 50V, + 10% Mylar | |
| R304 | 203X6500-886 | 10k Ohm, = 5%, 1/8W Carbon | 0317 | 202X8000-616 | 100 pF, 50V, + 10% Ceramic | |
| 305 | 203X6501-241 | 330k Ohm, * 5%, 1/8W Carbon | 6351 | 202X7000-281 | 1500 pF, 50V, + 10% Ceramic | |
| F306 | 203X6500-645 | 1k Ohm, + 5%, 1/8W Carbon | 352 | 202X7000-247 | 1000 pF, 50V, = 10% Ceramic | |
| R307 | 203X6500-689 | 1.5k Ohm, * 5%, 1/8W Carbon | C353 | 203X1100-573 | 0.022 uF, 50V, + 10% Mylar | |
| 309 | 203X6500-724 | 2.2k Ohm, + 5%, 1/8W Carbon | C355 | 203X1100-858 | 0.1 UF, 50V, + 10% Mylar | |
| R310 | 203X6501-285 | 470k Ohm, = 5%, 1/8W Carbon | 356 | 203X0015-105 | 4.7 uF, 25V Electrolytic | |
| R314 | 203%6501.065, | 56k Ohm, * 5%, V/8W Carbon | 6357 | 203X1201-013 | 0.015uF., 200V + 10% PP | |
| R312 | 203X6501-126 | 400k Ohm, * 5%, 1/8W Carbon | C358 | 203X1201.034 | 0.018 uF, 200V, + 10% PP | |
| R313 | 203X6001-326 | 40k Ohm, ‘+ 5%, 1/8W Carbon | C359 | 203X0040-013 | 4.7 uF, 160V Electrolytic | |
| R314 | 203X6501-044 | 47k Ohm, + 5%, 1/8W Carbon | C360 | 202X7000-482 | 0.01 uF, 50V, + 19% Ceramic | |
| R315 | 203X6500-628 | 820 Ohm, + 5%, /8W Carbon | 0361 | 203X1100-509 | 0.015 uF, 50V, + 10% Mylar | |
| R316 | 203X6500-420 | 120 Ohm, + 5%, 1/8W Carbon | 6362 | 203X0025-058 | 10 uF, 50V Electrolytic | |
| R317 | 203X6206-441 | 2.2 Ohm, + 5%, 1/2W Carbon | 6363, | 203X1205-487 | 0.01 uF, 630V, + 10% PP | |
| F319 | 203X6500-169 | 100 Ohm, * 5%, /W Carbon | C264 | 202X7000-482 | 0.01 uF, 50V, + 10% Ceramic | |
| F320 | 203X6500-927 | 18k Ohm, + 5%, 1/8W Carbon | ||||
| R321 | 203X6700-509 | 560 Ohm, + 5%, 1/2W Carbon | ||||
| Rage | 203X9100-121 | 22 Ohm, + 5%, 2W M.O. | SEMICONDUCTORS | |||
| R323 | 203X6500-689 | 4.5K Ohm, +5%, 1/8W Carbon | ||||
| A324 | 203X6500-988 | 27k Onm, = 5%, 1/8W Carbon | R301 | 200x4082614 | Transistor, 2S4826Q | |
| R325 | 203X6500-326 | 47 Ohm, = 5%, 1/8W Carbon | R302 | 200X3174-006 | Transistor, 28617400 | |
| R328 | 203X6500-628 | 820 Ohm, + 5%, 1/8W Carbon | TR303 | 200X3174-006 | Transistor, 2541740Q | |
| 330 | 203X6500-886 | 10k Ohm, + 5%, 1/8W Carbon | TR304 | 200X3174-006 | Transistor, 28C1740Q | |
| R331 | 203X6501-209 | 220k Ohm, + 5%, 1/8W Carbon | R305 | 200X4049-081 | Transistor, 26A490YLBGL! | |
| F351 | 203X6500-724 | 2.2k Ohm, + 5%, 1/8W Carbon | R306 | 200X3162.538 | Transistor, 28C1625YLBGLI | |
| R352 | 203X6500-927 | 45k Ohm, + 5%, 1/8W Carbon | TR307 | 200X3174.014 | Transistor, 28C1740R | |
| R353 | 203X6500-944 | 18k Ohm, + 5%, 1/8W Carbon | TR308 | 200X3174-006 | Transistor, 28C1740G | |
| Pasa | 203X6500-783 | 3.9k Ohm, + 5%, 1/8W Carbon | TR351 | 200X4085-415 | Transistor, 248540 | |
| R355, | 203X6500-902 | 42k Ohm, + 5%, 1/8W Carbon | TR352 | 200X3172-208 | Transistor, 2SC1722BKS | |
| F356 | 203X6500-581 | 470 Ohm, + 5%, 1/8W Carbon | TR353 | 200X3174.006 | Transistor, 28C1740Q | |
| R357 | 203X6500-724 | 22k Ohm, = 5%, 1/8W Carbon | TRO54 | 200X4082-614 | Transistor, 254826Q | |
| R358 | 203X6500-666 | 1.2k Ohm, * 5%, 1/8W Carbon | x301 | 201X2010-144 | Diode, (Sl) 1$2473-T72 | |
| R359 | 203X6501-088 | 68k Ohm, = 5%, 1/8W Carbon | X302 | 201X2010-144 | Diode, (SI) 1S2473-172 | |
| R360 | 203X5500-471 | 27 Ohm, + 5%, 1/4W Comp. | x303 | 200X8000-026 | Diode, (GE), INGOTVGL | |
| R361 | 203X6000-998 | 4.2k Ohm, © 5%, 1/8W Carbon | x304 | 200X8010-165 | Diode (SI) ISS81 | |
| R363 | 203X6500-666 | 1.2k Ohm, * 5%, 1/8W Carbon | X305 | 201X2010-165 | Diode (S!) ISS81 | |
| R364 | 203X9014-988 | 47k Ohm, x 5%, 1W MO. | X306 | 201X2010-165 | Diode (Si) ISS81 | |
| F365, | 203X6700-989 | 56k Ohm, x 5%, 1/2W Carbon | X307 | 200X8010-162 | Diode (SI) MA26W | |
| R366 | 203X6001.148 | 3.3k Ohm, #5%, VW Carbon | 308 | 200X8010-094 | Diode ($1) 182473 | |
| R367 | ‘340X2222-734 | 22k Ohm, = 5%, 1/2W Carbon | X31 | 201X2010-144 | Diode (St) 182473-172 | |
| F368 | 203X6500-785 | 3.9k Ohm, + 5%, 1/8W Carbon | x362 | 201X2010-144 | Diode ($1) 182479-T72 | |
| R369 | 203X6560-762 | 3.3k Ohm, = 5%, 1/4W Carbon | X353 | 201X2010-144 | Diode ($1) 1$2473-172 | |
| R370 | 302X6100-961 | 1k Ohm, + 5%, 1/4W Carbon | X354 | 201X2010-144 | Diode (S!j 1$2473-172 | |
| R71 | 203X6104-751 | 2.7k Ohm, | 5%, 1/4W Carbon | x355 | 200X8220-851 | Diode (Zener) RD10EBt |
| R383 | 340X2222-934 | 2.2k Ohm, *5%, VAW Carbon | X366 | 200X8100-130 | Diode (HS) RU-1 0.3 US | |
| F384 | 340X2822-934 | 8.2k Ohm, + 5%, 1/4W Carbon | ||||
| R301 | 204X2122.093 | Varistor, 250K Ohm, Vert, Hold | ||||
| R302 | 204X2114-065 | Varistor, 20K Ohm, Vert. Size | ||||
| R351 | 204x2114.059 | Varistor, 50K Ohm, Hor. Hold | MISCELLANEOUS | |||
| CAPACITORS | 301 | 204x9300-958, | Socket, 6 Pin | |||
| y | 9302 | 204X9300-958 | Socket, 6 Pin | |||
| : | DV, | 104 | 302 | 204x9601-195 | Plug, 6 Pin | |
| C304 | 203X1100-858, | 0.1 uF, SOV, “= 10% Mylar | ro | anes | baad | |
| 6306 | 203x0025-026 | 2.2 uF, 50V, Electrolytic | 201 | 201X0000;694: | ermistor | |
| ¢307 | 203X1100-928 | 45 uF, S0V, = 10% Mular | ||||
| €309 | 203X1100-858 | 0.1 uF, 50V, = 10% | Mylar | |||
| 310 | 203X0010.011 | 2 uF, 18V | Electrolytic | TRANSFORMERS & COILS | ||
| Catt | 203X0020-099 | 4000 uF, 35V Electrolytic | , | |||
| 0312 | 202X7000-469 | 0.0082 uF, 56V, + 10% Ceramic | uss1 | 201X5200-091 | Soil, Horiz. Ose. |
POWER BOARD (MV)
| 503 | 203x0010-011 | 22 UF, 16V Electrolytic | ||||
| RESISTORS | C551 | 203X0005-046 | 220 uF, 10V Electrolytic | |||
| R501 | 204X1725-052 | 180 Ohm, + 10%, 15W WW | ||||
| R502 | 203x6000-608 | 100 Ohm, + 5%, 1/8W Carbon | SEMICONDUCTORS | |||
| R503 | 203X6000-960 | 1k Ohm, + 5%, 1/8W Carbon | ||||
| R504 | 203X6000-879 | 560 Ohm, + 5%, 1/8W Carbon | TRS01 | 200X3174-006 | Transistor, 2861740Q | |
| R505 | 203X9014.965, | 39k Ohm, + 5%, 1W M.O. | 2 | TR502 | 200x3145-404 | Transistor, 28C1454 |
| R506 | 203X6500-842 | 6.8k Ohm, + 5%, 1/8W Carbon | TRSS1 | 200X3172-305 | Transistor, 2801723 | |
| 551 | 203X6500-420 | 120 Ohm, + 5%, 1/8W Carbon | x501 | 201X2230.042 | Diode, (SI) Zener EQB01-06V | |
| VR501 | 204X2050.001 | Varistor Vert. Adj. | X502 | 201X2010-144 | Diode, (S!) 1$2473-T72 |
CAPACITORS MISCELLANEOUS
| 501 | 203x0040-020 | 10 uF, 160V Electrolytic | 501 | 204x9300-958 | Socket, 6 Pin |
| 6502 | 202X7000-281 | 1500 pF, 50V, + 10% Ceramic | P501 | 204X9601-195 | Plug, 6 Pin |
| THS01 | 201X0000618 | Thermistor |
NECK BOARD (MS/QG)
| Ret. No. | Part No. | Description | Ret. No. | Part No. | Description |
RESISTORS
| aot | 203x6500-709 | ; | 5% tI | |||
| 402 | 203X6500-709 | {8k Onm 2 §¥6 {BW Carbon | C403 | eneeTo00 247 | 1000 pF, SOV, 10% Ceramic | |
| R403 | 203x6500-709 | 1.8k Ohm * 5% 1/8W Carbon | aed | 202X7110.019 | 1500 PF, 2kV + 10% Ceramic | |
| R04 | 203X6500-447 | 150 Ohm + 5% 1/8W Carbon | pei | 20eX7160-018 | 100 DP 12ky. = 10% -Caramic | |
| a | oases 431 | 220 Oh | 89s EW Gabon | C408 | 202X7050-483 | .01 UF, 500V, # 10% Ceramic |
| R408 | 203x6500.447 | 150 Ohm # 8% 1/BW Carbon | cao7 | 202X7110-019 | 1500 pF, 2kV | 10% Ceramic |
| R407 | 340X227 1-934 | 270 Ohm = 5% 1/4W Carbon | C408 | 202X8000-550 | 68 pF, SOV, = 10% Ceramic | |
| R408 | 203X6500-508 | 270 Ohm * 5% 1/8W Carbon | C408 | Precosnpeen | 88 pF, SOV, # 10% Ceramic | |
| R409 | 203X6500-800 | 4.7k Ohm | 5% 1/8W Carbon | cat0 | eoexe000e20) | 68 pF, 50V, + 10% Ceramic |
| Ra10 | 203X6500-800 | 47k Ohm + 5% 1/8W Carbon | ||||
| Ratt | 203x6500-800 | 47k Ohm + 5% 1/8W Carbon | ||||
| Rai2 | 203x9104-809 | 12k Ohm + 5% 2.0W Metal Oxide | ||||
| Ra13 | 203x9104-809 | 12k Ohm = 5% 2.0W Metal Oxide | SEMICONDUCTORS | |||
| Raid | 203X9104-809 | 42k Ohm + 5% 2.0W Metal Oxide | ||||
| R15 | 203x5601-313 | 27k Ohm = 10% 1/2W Comp. | TR401 | 200X3206-800 | Transistor, 2862068, 2SC1514 | |
| RaI6 | aaaxse0r 313 | 2.7k Ohm + 10% 1/2W Comp. | (Routput) | |||
| Ra17 | 203x8601-313 | 2.7k Ohm £ 10% 1/2W Comp. | TR402 | 200X3206-800 | ti | 2sci5i4 |
| R418 | 203X5602-254 | 470k Ohm + 10% 1/2W Comp. | (G output, BSC 2008, 280181 | |||
| R419 | 203x5602-185 | 330k Ohm + 10% 1/2W Comp. | ’ | |||
| R422 | 203X9105-117 | 1:0 Ohm + 10% 2W Metal Oxide | T*#08 | 200%3206-800 | aa |
X5 102-155 K %
| x405 | 201X2100-126 | Diode, 182367 (protector) | |||||
| vag | 204x2115-014 | 500 Ohm Varistor B Drive | ee | certrarey | lode, | 182367 | (p' |
| R403 | 204X2115-006 | 5k Ohm Varistor R Cutoff | 201x210 | Plode, 1$2967 (protecton | |||
| vR4o4 | 204X21 15-006 | 5k Ohm Varistor G Cutoff | |||||
| R405 | 204X2115-006 | 5k Ohm Varistor B Cutoff | |||||
| R406 | 204x2000-025 | 1M Ohm Varistor Screen | MISCELLANEOUS | ||||
| CAPACITORS | 401 | 206X5003-729 | Socket, 5 Pin | ||||
| 402 | 206X5003-983 | Socket, 3 Pin | |||||
| cao1 | 202x7000-247 | 1000 pF, 50V, 10% Ceramic | 401 | 204x9600.329 | Plug, 5 Pin | ||
| aoe | 202X7000-247 | 1000 pF, 50V, 10% Ceramic | 402 | 204X9600-254 | Plug, 3 Pin |
4 297X2000-072 HIGH VOLTAGE ASSEMBLY (T701)
Ax R701 R702 x701 x702 X703 204X 1625-058 204X3901-125 3.3 Ohm, + 10% 10W WW Resistor Focus Control Diode (SI HV) Diode (SI HV) & Part of T701 Diode (SI HV) FINAL ASSEMBLY PARTS
4% 88x.0129-506 19VJTP22 Pix Tube 38A5554-000 Assy. Purity Shid/Degaussing 205X9800-256 Lateral/Purity Assembly Aye 202X1110-810 Yoke, Deflection 208X2000-946 CRT Socket 297x2000-072 HV Unit (1701) 6A0397 Plug, Line Cord 9A2753-003 Degaussing Coil (L701) R201 R202 R203 R204 R205 R206 R207 R208 R209 R210
C202
C204
TR201 TR202 TR203 TR204 TR205 TR206 TR207 TR208 TR209 TR210 x201 x202 X203 X204 20201 INTERFACE BOARD (P317)
RESISTORS
| 340X3010.934 | 91 Ohm +5%, 1/2W Carbon | R211 | |
| 340X3183-044 | 18k Ohm + 10%, 1/2W Carbon | R212 | |
| 340X3102-934 | 1k Ohm 5%, 1/2W Carbon | R213 | |
| 340x2101-934 | 100 Ohm | 5%, 1/4W Carbon | Raid |
| 340X2333-934 | 33k Ohm + 5%, 1/4W Carbon | R215 | |
| 340X3331-944 | 330 Ohm + 10%, 1/2W Carbon | R216 | |
| 340X3102-934 | 1k Ohm 5%, 1/2W Carbon | R217 | |
| 340X3102-934 | 1k Ohm #5%, 1/2W Carbon | R218 | |
| 340X2333-934 | 33k Ohm = 5%, 1/4W Carbon | R219 | |
| 340X2101-934 | 400 Ohm +5%, 1/4W Carbon | R220 |
R221 R222 CAPACITORS R223
| 45X0524-038 | 100 uF, 16V Electrolytic | Bese |
| 45X0524-053 | 470 uF, 18V Lytic | ieee |
| 349X2232-109 | 022 uF, 10%, 100V | Lo |
| 80X0099.020 | 680 pF, 10%, Z5F | Gesot |
R202
SEMICONDUCTORS 86X0121-001 Transistor (NPN) MPS-A20 86X0121-001 Transistor (NPN) MPS-A20
| 86X0121-001 | Transistor (NPN) MPS-A20 | 201 |
| 86X0066-001 | Transistor (PNP) MPS-A70 | “ja02 |
| 86X0066-001 | Transistor (PNP) MPS-A70 | a |
| 86X0066-001 | Transistor (PNP) MPS-A70 | eae |
| 86X0121-001 | Transistor (NPN) MPS-A20 | boos |
86X0121-001 Transistor (NPN) MPS-A20 86X0121-001 Transistor (NPN) MPS-A20 86X0121-001 Transistor (NPN) MPS-A20 66X0046-001 Diode Silicon FDH-444 66X0046-001 Diode Silicon FDH-444 66X0046-001 Diode Silicon FDH-444 66X0046-001 Diode Silicon FDH-444 66X0040-019 Diode, Zener 6.8V, 5%, 0.5W IN5235B
soms208
“} 85xX0149 340X2331-934 340X2331-934 340X2331.934 340X2151-934 340X2151-934 340X2151-934 340X2101-934 340X3102-934 340X3102-934 340X3681-934 340X3271-934 340X3271-934 330 Ohm +5%, 1/4W Carbon 330 Ohm +5%, 1/4W Carbon 330 Ohm +5%, 1/4W Carbon 150 Ohm +5%, 1/4W Carbon 150 Ohm +5%, 1/4W Carbon 150 Ohm +5%, 1/4W Carbon 100 Ohm +5%, 1/4W Carbon 1k Ohm +5%, 1/2W Carbon 1k Ohm +5%, 1/2W Carbon 680 Ohm, 5%, 1/2W Carbon 270 Ohm, 5%, 1/2W Carbon 270 Ohm, 5%, 1/2W Carbon 340X2104-934 100k Ohm, 5%, 1/4W Carbon 340X3102-934 1k Ohm, 5%, 1/2W Carbon 340X2822-934 8.2k Ohm, 5%, 1/4W Carbon 340X2822-934 8.2k Ohm, 5%, 1/4W Carbon 340X2822-934 8.2k Ohm, 5%, 1/4W Carbon 40X0590-017 1.5k Ohm Black Level Control 40X0592-007 10k Ohm Horizontal Centering
MISCELLANEOUS
204X9300-958 Socket, 6 Pin 204X9300-958 Socket, 6 Pin 204X9600-845 Plug, 4 Pin 6393-003 Plug, 3 Pin 6A0393-006 Plug, 6 Pin
WGEC SERIES K4600 69X1077-100
VERTICAL RASTER POSITION ADJUSTMENT
CENTER uP DOWN &
rece [i Main BOARD [Ma=29 sone tae vest V.Osc 7 VPRE DRIVE | DRIVE ao Dw OUF VAMP pein orc, 2882 tsoz 25C7HE rp: ! 2SC17AO yp, 1740 t 19”COLOR MONITOR SCHEMATIC DIAGRAM
Lez wont SIZE con
crsee® |
VERT/HOR ‘BOARD % Paced)
TR306. 2bciees
mar 22 (Ror "gi PROTECTOR TRIS4 254025, R383 2sci790/ 2501815 _2SAN0I5 /25a826 226 Snaz7 P08 eae Stak aw, 568 tam, 8%
L
[oxo 0 Leap) coo fas
oecagasine
28c17 28c 108 28Ciase 281693 127607 TUbIO POWER eoa#o ERROR AMP 2 f aso) 25C 7780, aat {MV J) asoe Fecians fo po 4] HORIZ. RASTER | POSITION ADs.
CRT 19vsTP22
[service ror Focus: se)
K4625, K49626, 44675 -5816 Dw