CATHODE RAY TOMES

Midway Sportstation 39in Deluxe

SportStation (Midway Games Inc., 1999) · Manual · 133 pages · 60 sections · original scan

Page 1

SEPT 1999 MIDWAY 16-40098-101 ~ GAMES INC.

http:/Awww.midway.com

4-PLAYER DEDICATED 39” VIDEO GAME

Operation

¢ US

LISTED Man ual

@lnstalling @Operating @Testing @Parts @Wiring Diagrams @Troubleshooting

MIDWAY GAMES INC., 3401 North California Avenue, Chicago, Illinois 60618-5899 USA

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

SPORTSTATION

CHAPTER

ONE

SAFETY, SPECIFICATIONS, INSPECTION & INSTALLATION

NOTICE: This manual is subject to change without notice. MIDWAY reserves the right to make improvements in equipment function, design, or components as progress in engineering or manufacturing methods may warrant. Fill out and mail in the Game Information Card. Include the game serial number from the label on the rear of the cabinet. For your records, write the game serial number in the manual. SERIAL NUMBER

Page 4

SAFETY INSTRUCTIONS

The following safety instructions apply to operators and service personnel. Read these instructions before preparing your game for play. Other safety instructions appear throughout this manual.

DEFINITIONS OF SAFETY TERMS

DANGER indicates an imminent hazard. If you fail to avoid this hazard, it WILL cause death or serious injury.
WARNING indicates a potential hazard. If you fail to avoid this hazard, it COULD cause death or serious injury.
CAUTION indicates a potential hazard. If you fail to avoid this hazard, it MAY cause minor or moderate injury. CAUTION also alerts you about unsafe practices.

NOTICE indicates information of special importance.

WARNING: TRANSPORTING GAMES. This game contains glass and fragile electronic devices. Use appropriate care when transporting this game. Avoid rough handling when moving the cabinet. Do not move this game with the power on.
WARNING: DISCONNECT POWER. Always turn the power OFF and unplug the game before attempting service or adjustments. Installing or repairing PC boards with power ON can damage components and void the warranty. Be sure that you securely install ground wires.
WARNING: GROUND GAMES. Avoid electrical shocks! Do not plug in a game until you have inspected and properly grounded it. Only plug this game into a grounded, three-wire outlet. Do not use a “cheater” plug, or cut off the ground pin on the line cord.
WARNING: HAZARD TO EPILEPTICS. A very small portion of the population has a condition which may cause epileptic seizures or momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition. If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), immediately consult your physician before using any video games.

We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician. @ bP @Pr

WARNING: AVOID ELECTRICAL SHOCKS. This video game system does not utilize an isolation transformer. Internal, cabinet AC isn’t isolated from the external, AC line.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

1-2

Page 5
CAUTION: CHECK POWER SELECTOR. Set the 110/220VAC selector on the power supply for the correct line voltage in your area. Check the selector setting before switching on the game.
CAUTION: USE PROPER FUSE. Avoid electrical shock! Replacement fuses must be of the same type as those they replace. Fuse voltage and current ratings must match ratings on the original fuse.
CAUTION: ATTACH CONNECTORS PROPERLY. Be sure that printed circuit board (PCB) connectors mate properly. If connectors do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Connector keys only allow a connector to fit one set of pins on a board.
CAUTION: TAKE CARE WHEN SHIPPING HARD DISKS. The hard disk drive must be packed in an anti-static bag. When shipping the drive for repair or replacement, pack it in an approved container (P/N 08-8068). Never stack or drop hard disk drives.

1-3

Page 6

PRODUCT SPECIFICATIONS

Operating Requirements Location Electrical Power Domestic 120VAC @ 60Hz 4.0 Amps Foreign 230VAC @ 50Hz 2.0 Amps Japan 100VAC @ 50Hz 4.0 Amps

Cabinet Statistics Shipping Dimensions (Two Pieces) Carton Main Cabinet Control Section Temperature 32°F to 100°F (0°C to 38°C)

Shipping Weight Main Cab Control Sect

Width46"(115cm)50” (127 cm)600 Lbs.200 Lbs.
Depth39"(99cm)42°(107cm)272kg.91kg.
Height87" (221m)52” (131 cm)

Equipment Characteristics Video Display Monitor Audio System Medium Resolution RGB 38” (96.5 cm) CRT Digital Stereo Sound

  • 4.5” (8 cm) Full-Range
  • 8” (20 cm) Woofer

Game Characteristics Player Variables 1 to 4 Players Per Game High Score Recognition Parental Advisory Disclosure: “Suitable for all Ages” Operator Variables Coinage, Game Options, Difficulty, Volume, Audits, Statistics

1-4 Humidity Not to exceed 95% relative

Design Type Dedicated Video Game with 49-Way, Optodetector Joysticks

Currency Acceptors 2 Coin Mechanism, Coin Counter Dollar Bill Validator Ready Electronic Coin Acceptor Ready

Diagnostics Automatic Power-On Self-Test Manual Multi-Level Menu System

Page 7

INSPECTION & INSTALLATION

NOTICE: The factory ships this game on a skid. To move or pick up the game, you need a fork truck or pallet jack.

WARNING: The cabinet is top heavy. When moving the cabinet, do not push against plastic or glass parts.
  • Remove all items from the shipping containers and set them aside. Remove all packing material from the joysticks. Inspect the exterior of the main cabinet and control section for damage.
  • The main cabinet is mounted on four swivel casters. Roll the cabinet to its intended location. Maintain clearance between the cabinet and walls, drapes, other games, etc. Lower each leg leveler until the cabinet is stable and level. Adjust the levelers to raise the wheels up off the floor and distribute weight equally on each corner. When the cabinet is level and stable, tighten the leveler nuts.

SETTING UP THE CONTROL SECTION

  • Reach into the harness access opening of each cabinet section. Pull forward to expose the cables. Guide the control section harness into the main cabinet. Mate each control cable with its cabinet cable. Press connectors firmly to seat them.

1-5

Page 8

1-6

Page 9

CABINET ASSEMBLY

1-7

Page 10

ATTACHMENT OF CONTROL SECTION TO MAIN CABINET

  • Front door and monitor access door keys are on the rear of the monitor cabinet. Look for the key hook toward the top of the cabinet back. The cash box key is with the control section. Unlock and open the coin door. Unlock and open the cash box door. Remove the spare parts stored in the cash box.
  • Unlock the monitor section front door. Swing it open and allow it to rest on the support chains. Inspect the cabinet interior for any signs of damage. Check that all major assemblies are mounted securely.
  • Refer to the Cabinet Wiring Diagram (Chapter Five), and check to see that all cable connectors are correctly secured. Do not force connectors; they are keyed to fit in only one location. Bent pins and reversed connections may damage your game and void the warranty.
  • Place one lock washer and one flat washer onto each of the bolts from the spare parts bag. Align the control section holes with the main cabinet holes. Install one bolt with its washers through the control section and into each threaded cabinet hole. Tighten all bolts securely. Tighten the leveler nuts.
  • Place one cover cap washer onto each screw from the spare parts bag. Place a filler panel over the control section bolt access opening. Align filler panel holes with control section holes. Install one screw with its washer through the panel and into each control section hole. Repeat the installation for the remaining panel. Tighten all screws firmly. Snap decorative cover caps over screws.
  • The line cord is with the spare parts. Match holes on the IEC plug with the prongs in the receptacle and push firmly to seat the line cord. Route the cord away from cabinet wheels and foot traffic areas.
CAUTION: CHECK POWER SELECTOR. Set the 110/220VAC selector on the power supply for the correct line voltage in your area. Check the selector setting before switching on the game.
  • Plug the game into a grounded (3-terminal) AC wall outlet. Switch ON the game, using the ON/OFF switch at the center left rear of the cabinet. The game will power up and begin self-diagnostics. If no errors are found, the game will automatically enter its Attract Mode. Unlock and open the coin door. Locate the diagnostic control switches. Press TEST MODE to enter the Menu System.

1-8

Page 11

SPORTSTATION

CHAPTER

TWO

OPERATION, FEATURES, MAINTENANCE & SERVICING

Page 12

GAME OPERATION

STARTING UP

Whenever you turn on the machine or restore power, the system executes boot ROM code. The boot ROM contains self-diagnostic tests that automatically verify and report the condition of the disk drive and other hardware. The screen is blank during these tests. If the hardware fails a test, the system displays an error message. The message appears for 30 seconds or until someone presses a button. e — If nobody presses a button, the system quickly completes tests, and then loads game software. e To skip boot ROM tests and activate the Menu System, press and hold the TEST MODE button. Youll find this button behind the coin door.

Having passed power-up tests, the system enters Attract Mode. Attract Mode consists of typical game scenes and sounds, alternating with high scores. Attract Mode continues until game play commences.

Players insert currency or tokens to start the game. Pressing a START determines which player receives the credit. The game computer asks whether players want to play NBA Showtime™ or NFL Blitz 2000 Gold Edition™. Players request one or the other via player panel controls. Then players select a team. The game computer associates one team with the Player-1 and Player-2 joysticks. The Player-3 and Player-4 joysticks assume control of the opposing team. Play begins after a countdown period. Play progresses like a real-life football or basketball game. At Game Over Mode, players may choose to begin again. If players choose not to continue, then the system returns to Attract Mode.

NFL BLITZ 2000 GOLD EDITION GAME RULES

INSTRUCTIONS Play instructions appear on the information panel over and under the video monitor.

ONE TO FOUR PLAYERS Players may enter their names for future reference. Then they select teams and run the first play. Players may choose an offensive or defensive play. Additional game information appears on the screen as needed. Team statistics appear at the end of each quarter.

CONTROLLING CHARACTERS The joystick and action buttons control characters on the field. The joysticks respond to different amounts of deflection as well as direction.

GAME ACTION Standard league football rules apply, with two exceptions: First downs require 30 yards, and teams only have seven active players. Game adjustment settings determine game length and speed. The player view of the action changes automatically whenever a better camera angle becomes available. The game sounds include announcer comments and crowd noises.

SCORING Touchdowns and field goals score points, just as in real football games.

NFL BLITZ 2000 GOLD EDITION PLAY SELECTION

STANDARD PLAYS The player may select any of the offensive or defensive plays in the game. Players can choose from pages of standard plays loaded into the game. Use the indicated pushbuttons to view and select any play. CUSTOM PLAYS Players may choose to create their own offensive plays rather than depend on the standard plays in the game. Players can design and name their plays using the CREATE PLAY feature, then store these plays for future use. These custom plays become available on an additional page of game plays.

2-2

Page 13

NFL BLITZ 2000 GOLD EDITION PLAYER CONTROLS

The player controls are used to maneuver the team members and attack or defend against adversaries.

NOTICE: Use joystick and button combinations to discover secret moves.

e START (orange). This button allows players to begin or continue play. Use PLAYER 1 START and PLAYER 2 START to begin a two-player game. START has no game action or service function.

e JUMP / TACKLE (red). This button lifts the offensive team member up or causes the defensive player to tackle opponents. Use this same button to create plays or select menu items during service.

e PASS / CHANGE PLAYER (blue). This button activates offensive throws. The defense move switches active control to another teammate. Use this same button to create plays or select menu items during service.

e TURBO (white). The TURBO button gives any active character an extra burst of power or speed. Use this same button to create plays or select menu items during service. e JOYSTICK. Each player has a joystick to control the movements of one on-screen character at a time. Use the joystick to create plays or select menu items during service.

MP /TECKLE (4) i tr Pass /CHENSE PLEER (P ELE

Tek

RECOMMENDED PLAYER CONTROL LOCATIONS

2-3

Page 14

NBA SHOWTIME GAME RULES

INSTRUCTIONS Play instructions appear on the information panel over and under the video monitor.

ONE TO FOUR PLAYERS The player or players insert currency to start the game. Each player chooses a joystick and presses the nearest START button. Players select a team and two characters. In four-player games, each player controls one character. In games with fewer players, each player controls one character. The game computer controls remaining characters. The game displays team scores and statistics at the end of each quarter. Additional game information appears on screen as needed.

CONTROLLING CHARACTERS The joystick and action buttons control characters on the basketball court. The joysticks respond to different amounts of deflection as well as direction.

GAME ACTION Standard NBA basketball rules apply, except that the game only includes four active characters. Game settings determine game length and speed. The player view of the action changes automatically whenever a better camera angle becomes available. Game sounds include announcer comments and crowd noises.

SCORING The game awards points for baskets, just as in real basketball games.

NBA SHOWTIME PLAYER CONTROLS

e JOYSTICK. Each player's joystick controls the position of that player’s characters on the game screen.

e PASS/STEAL (the blue button) controls character actions on the game screen. Press PASS/STEAL to attempt to pass or steal the ball.

e SHOOT/BLOCK (the red button) controls character actions on the game screen. Press SHOOT/BLOCK to shoot or attempt to block the ball.

e START (orange buttons). Each START button allows the corresponding player to begin or continue play.

e TURBO (The white button) controls character actions on the game screen. Press TURBO to speed up the pace of a play.

TART . psss/STEAL (F

am Hi

Thr

2-4

Page 15

RECOMMENDED PLAYER CONTROL LOCATIONS NBA SHOWTIME GAME FEATURES

NBA Showtime is a thrilling, two-on-two basketball game with world-class realism. Each player selects an NBA team, and then chooses a favorite character. Players can also create their own players. If fewer than four players are in the game, the computer operates the remaining characters.

The red team comprises players 1 and 2. Players 3 and 4 make up the challenging, blue team. The red and blue teams square off for the jump and the action begins. Run the ball down court! A steal! Dribble up court! A snap shot! The breathless announcer describes every pass, every shot, every block, every move!

After each quarter, new players can join the fun. Players can also switch to different characters. When the game concludes, team and individual scores appear on the screen. Top scorers may enter their initials or names with a joystick. NBA Showtime displays these initials in a high score table.

OPERATOR CONTROLS

CABINET CONTROLS

e¢ The DIP Switches set some system variables. You can set other variables with diagnostic control switches.

e¢ The Monitor Remote Control Board allows you to adjust the video display for optimum viewing.

¢ The POWER Switch turns off the game, but does not reset game variables.

DIAGNOSTIC CONTROL SWITCHES

e The SERVICE CREDITS Button allots credits without changing the game's bookkeeping total. SERVICE CREDITS has no function in the menu system.

« The TEST MODE Button causes the game to enter the service menu system. Press the TEST MODE button briefly to run automatic tests. To make game adjustments, press and hold TEST MODE until the Main Menu appears. Within the menu system, TEST MODE assumes another function. There, it selects a menu line item and calls up the item’s submenu. The screen displays this submenu.

e VOLUME DOWN and VOLUME UP Buttons set game sound levels. To make minor volume changes, press either button briefly. To make major changes, press and hold a button. In the menu system, VOLUME UP moves the item highlight bar up the menu. VOLUME DOWN moves the item highlight bar downward.

NOTICE: You must adjust Attract Mode volume independently of Game Mode volume. For greater profits, increase volume levels to draw attention to this game.

HTPOL SwITCHE

oom were 4 ae

2-5

Page 16

DIAGNOSTIC CONTROL SWITCH LOCATIONS (TYPICAL INSTALLATION)

MAINTENANCE

Cabinet Use only non-abrasive cleaners to avoid damaging game graphics. Apply cleaner to a clean cloth or sponge. Wipe the screen clean with this cloth or sponge. Do not apply cleaner directly on the cabinet!

Control Panel Dirt or debris on the joysticks or buttons can affect earnings. Apply the cleaner to a clean cloth. Use the cloth to wipe the controls. Don’t apply the cleaner directly to the controls!

Viewing Glass To clean the glass, you don’t need to switch off power to the game. Apply a mild glass cleaner to a clean cloth or sponge. Use this to wipe the viewing glass. Do not apply the cleaner directly on the glass! Liquid could drip down into switch or motor circuits and cause erratic game operation.

SERVICING

Only qualified service personnel should perform maintenance and repairs. The following product guidelines apply to all game operators and service personnel. Notes, Cautions and Warnings appear throughout this manual where they apply. Read the SAFETY pages thoroughly before beginning service. Circuit Board Set The game computer uses a set of three circuit boards. The three boards include the CPU Board, I/O Board and Video Board. Switch off power to the game. Open the front access panel. To expose the circuit boards, remove their perforated metal cover. Carefully note the orientation of the JAMMA connector and other cables. Extract the harness and hard disk drive ribbon cable from the board connectors. Remove circuit board mounting screws. Lift the circuit boards out of the cabinet and set them in a safe place. Use anti-static packaging from new parts to store boards that you won't reinstall.

CAUTION: Circuit board edge connectors are fragile. Take care when separating boards in the board set. Never jam the board connectors together. Never plug them together on an extreme angle. If necessary, carefully straighten bent pins with a small, grounded flat blade screwdriver. Also, don’t touch exposed foil on printed circuit boards. Skin oils are corrosive.

NOTICE: Avoid damage to game electronics! Turn off game power before servicing circuit boards or any electronic assembly. Never “hot plug” circuit boards.

Coin Mechanism Switch off power to the game. Unlock the coin door and swing it open. To clean or replace a coin mechanism, unlatch and remove it. After reinstallation, ensure that the mechanism seats fully its bracket. Close and lock the release latch, and then close the door. Turn on the game and change the mechanism setup. Test known good and bad coins to verify operation.

Coin Meter Switch off power to the game. Unlock the cash door and swing it open. The coin meter mounts to a metal plate at the bottom the cash vault. Record the meter count before testing or replacement. Remove the plate’s four mounting screws, and then remove the plate.

Disconnect the meter wiring harness at the connectors. Remove front screws and slide the meter out. Assure that a protective diode connects across the replacement meter’s terminals. The diode prevents driver circuit damage.

2-6

Page 17

Hard Disk Drive Switch off power to the game. Unlock and remove the front access panel. Remove the perforated metal cover over the game electronics. Disconnect the DC power cable from the hard disk drive. Don’t disconnect the cables from the CPU Board. Unplug the ribbon cable from the hard drive. Loosen the drive mounting screws and lift the drive out of its mounting bracket. Remove the screws. Save them for reuse in future hard drive installations. When returning a hard drive to your distributor, pack it in an anti-static bag. Box the drive in approved shipping container 08-8068.

NOTICE: Hard disk drives are very fragile! Handle them with care. Do not stack or drop hard disk drives. Keep disk drives away from magnets, heat and vibration.

Power Supply Switch off power to the game and disconnect the line cord. Unlock and open the front door. Unplug the wiring harnesses from the back of the supply. Don’t remove the supply mounting bracket. Remove two rear screws from the supply. Then slide the unit out of the cabinet. Verify the line VOLTAGE switch setting before reinstalling the power supply.

Speakers Switch off power to the game. The full-range speakers are mounted behind grilles at the top of the control section. Grilles and speakers come out from the front. Remove the screws and set the grilles aside. To avoid damaging a speaker, remove upper mounting screws first, and replace them last. Remove the speakers from the enclosure just enough to expose the terminals. Label and disconnect the wires. Refer to the Wiring Diagram (Chapter Five) for speaker wiring information. Don’t use excessive force when removing or tightening screws threaded into plastic or particle board.

Joysticks Switch off power to the game. Open the player panel on the pod assembly. Mark and disconnect the wiring harness from a joystick. To separate the joystick from the player panel, first remove the joystick shaft. An E-ring secures the shaft. Disengage this E-ring with a small, flatblade screwdriver. Grasp the joystick knob. Extract the stick from the assembly. Then remove the tamper-resistant bolts from the corners of the joystick base. Retain fasteners for reassembly.

Memory

ry CAUTION: Static electricity builds up on your body. This static can damage or

destroy sensitive the game circuits. BEFORE touching or handling electronic \Y assemblies, discharge static electricity by touching the electronics mounting plate.

NOTICE: CPU Board and SI/O Board chips don’t face same direction. When mounting chips on either board, refer only to chips on the same board for reference.

ROM (Read Only Memory) circuits contain computer operating instructions for this game. Switch off power to the game. Unlock and remove the rear door. Remove the perforated metal cover. Note the ROM chip position. Remove the device with a chip extraction tool. To reinstall a ROM chip, orient the device over its socket. Press the chip firmly to seat pins. Don’t force the chip into the socket.

Monitor

CAUTION: The video monitor is heavy, with most of the weight toward the front of the assembly. Removing the monitor is a two-person task. Don’t attempt to remove it by yourself. One person must support the monitor as the other removes it from the cabinet.

Switch off power to the game. Open the front cabinet door. Disconnect the fluorescent light assembly connector and all monitor cables. Remove the front housing hinge screws and set the housing aside. 2-7

Page 18

Remove the monitor bezel and both barrier panels. Remove the four flange nuts securing the monitor's mounting brackets to its mounting panel. Pull the monitor carefully from the cabinet and set in a safe place. The monitor remote adjustment board is behind the front door with the rest of the electronics. Clean the face of the CRT before reinstalling the barrier panels and the monitor bezel.

Viewing Glass Switch off power to the game. Open the front cabinet door. To replace the viewing glass, you must completely remove the front housing from the monitor cabinet. Lift the glass out of the front housing. Clean the glass before reinstalling it. Install the bracket and tighten screws. Replace the front housing on the monitor cabinet. Tighten mounting screws. Don’t use excess force.

CAUTION: Before you replace the CRT glass, completely remove the front housing assembly from the cabinet. Glass is hazardous to handle with the housing pivoted up on the drop rod.

Marquee Switch off power to the game. Open the front cabinet door. To replace the marquee, you must completely remove the front housing from the monitor cabinet. Then you can access the marquee, and remove it from the bezel. Take the glass and artwork out of the front housing. Clean the glass before reinstalling it. Install the bracket and tighten screws. Replace the front housing on the monitor cabinet. Tighten mounting screws. Don’t use excess force.

GAME ELECTRONICS f ELECTIONS _ 1 PIP S0rtcH Eh H

EMPL EROE FL Fell 4 FE

EMBL

HERD PEIVE POWER CAPLE Fell 4 OEMBLy REVERSE FL _FERPIDE DEAL

f i b SHELF — i

METAL HOU NTI PLETE HIELD VIREO CABLE — we EMPL

EO CARD bRACKET ne 20=PIN RIBBON CABLE FUSE BLOCH HEED Dick DRIVE . 10 PIN-PIBBCH CAPLE™ Herb Pio PRRE__ PSE bloc S59EMPL AUX ADAPTER BORE SSSEMEL

2-8

Page 19

INTERNAL COMPONENTS

2-9

Page 20

SPORTSTATION

CHAPTER

THREE

DIAGNOSTIC, AUDIT & ADJUSTMENT MENU SYSTEM

FOR NFL BLITZ 2000 GOLD EDITION GAMES

NOTICE: Information in this manual is subject to change without notice. Midway reserves the right to make improvements in equipment as progress in engineering warrants.

NOTICE: GAME-SELECTION SWITCH. Select NBA Showtime or NFL Blitz 2000 Gold Edition by flipping switch 8 at DIP bank U13. Then power down and up again. The Attract Mode for the game you select will appear. The player can still play either game.

3-1

Page 21

MENU SYSTEM

WHAT IS THE MENU SYSTEM?

The game’s Menu System is a series of auditing, game adjustment and diagnostic screens. You can easily access and apply these screens to optimize game performance. For instance... e Use game audits screens to assess game performance. e Use adjustment screens to help you to customize game performance. For instance, you can restore factory default game settings. You can also calibrate player controls for accuracy. e Use diagnostic screens to verify proper equipment operation.

ACTIVATING THE MENU SYSTEM

Open the coin door. Find the TEST MODE switch inside. Press TEST MODE to invoke the Menu System. The game system responds by exiting Game Mode and entering Diagnostic Mode.

AUTOMATIC TESTS In Diagnostic Mode, the Power-On Self-Test (POST) activates. This routine runs automatically. It can detect faults that cause game or Menu System malfunctions. POST usually takes less than a minute. The test doesn’t display anything. Instead, the system boot loader indicates the software revision number and serial numbers. The system boot loader also displays a sound-loading message and other useful information. At the end of POST, the system displays the Control Functions Screen.

CONTROL FUNCTIONS SCREEN The Control Functions Screen is purely informational. It appears for five seconds. Then the Menu System automatically displays the Dual Game Adjustment Screen. The Control Functions Screen introduces the menu navigation controls. The key point is that you can use either player or diagnostic controls to navigate menus. Diagnostic control switches are particularly helpful when you must troubleshoot player switches. This manual discusses the controls in more detail in this chapter’s Main Menu section. Also see the page on the menu that interests you.

STICK UP/VOLUME UP - MOVE UP

STICK DOWN/VOLUME DOWN - MOVE DOWN

STICK RIGHT - MOVE RIGHT

STICK LEFT - MOVE LEFT

PUSH BUTTON/TEST BUTTON - SELECT

5 SECONDS TO DIAG ENTRY

CONTROL FUNCTIONS SCREEN

3-2

Page 22

DUAL GAME ADJUSTMENT SCREEN

The Dual Game Adjustment Screen is another informational, read-only screen. It appears until you choose to exit. This screen reminds you that some NFL Blitz settings also affect NBA Showtime game play. Press any button to exit to the Main Menu.

ATTENTION!

ANY CHANGES TO THE FOLLOWING ADJUSTMENTS.

UPDATE BOTH NBA AND NFL

PRICING

FREE PLAY

VOLUME LEVEL

DISCOUNT PRICE / CREDITS

ATTRACT MODE SOUND ON / OFF

THIS ALSO INCLUDES DEFAULT ADJUSTMENTS.

AND

FULL FACTORY RESTORE FUNCTIONS.

PRESS ANY BUTTON TO EXI

DUAL GAME ADJUSTMENT SCREEN

MAIN MENU

The Main Menu offers you access to the game machine's test, bookkeeping and programmable features. Game audits, adjustments and diagnostics are line items on the Main Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.

NFL MAIN MENU

DIAGNOSTICS AUDITS ADJUSTMENTS VOLUME LEVEL UTILITIES NBA MAIN MENU EXIT TO NBA EXIT TO NFL

MAIN MENU

MENU LAYOUT Menus differ, but related information tends to occupy the same screen locations.

e The block at the top, center of each screen displays the current menu title. e Data (menu items, video signals, statistics, reports, etc.) appears in the center of the screen. e Messages (explanations, control functions, revision levels) display at the bottom of the screen.

MENU NAVIGATION CONTROLS. Use any player panel joystick to highlight a desired menu item. You can only select one highlighted item at a time. To select a highlighted item, press any player panel button. Operator control buttons inside the coin door serve as backup menu navigation controls. Press VOLUME UP or VOLUME DOWN buttons to highlight a menu item. Press TEST MODE to select a highlighted item.

EXIT OPTIONS

3-3

Page 23

To exit the NFL menus and simultaneously enter the NBA menus, choose NBA MAIN MENU. To return the game to play, highlight either EXIT TO NFL or EXIT TO NBA. Your choice determines the game that will boot. Next, press any button. Main Menu (continued) Diagnostics Menu

DIAGNOSTICS MENU Select DIAGNOSTICS at the Main Menu. Diagnostic tests allow you to verify the condition of the electrical and electronic hardware in the game. Highlight a test with any player panel joystick. Select the option with any player panel button.

DIAGNOSTICS

MONITOR SETUP.

SYSTEM INFO

SOUND SUBSYSTEM

DISK TESTS

SWITCH TESTS

DIP-SWITCH TESTS

SPEAKER TEST

EXIT

DIAGNOSTICS MENU

Diagnostic tests assist you in checking and adjusting the game’s major systems. By running diagnostics, you can gain an insight into both system hardware and game software. Periodically running diagnostics is a crucial part of maintaining game performance and player satisfaction. Sometimes you can improve game performance by running a diagnostic test and making appropriate adjustments.

3-4

Page 24

Main Menu (continued) Diagnostics Menu (continued) Monitor Setup Menu

MONITOR SETUP MENU Select MONITOR SETUP at the Diagnostics Menu. The Monitor Patterns routine provides test screens to verify monitor performance or make adjustments. Highlight an option with any player panel joystick. Select the option with any player panel button.

MONITOR SETUP.

COLOR BARS

CROSSHATCH

RED SCREEN

BLUE SCREEN

GREEN SCREEN

WHITE SCREEN

BLACK SCREEN

50 PCT. GRAY SCREEN

25 PCT. GRAY SCREEN

EXIT

MONITOR SETUP MENU

Color Bars fills the screen with colored stripes. Use the color bars to help you to check or adjust monitor brightness and contrast. The color bars also expose defects in horizontal linearity. Each color bar consists of 32 intensity levels. On a properly adjusted monitor, the top 31 of these levels are visible. Each bar should appear sharp, clear and distinct from bars on either side. Incorrect adjustment can cause missing detail at the top or bottom of a bar. Bent bars indicate horizontal linearity flaws, such as pie crust, pincushion or barrel distortion. (Correct color bar colors, left to right: Red, Green, Blue, Black, White, Cyan, Yellow, Violet.) Set controls as follows: 1. Adjust BRIGHTNESS and CONTRAST to minimum. 2. Turn up BRIGHTNESS until the pixels in the black stripe begin to glow (turn dark gray). 3. Bring up the CONTRAST control until you can see 31 bars. Crosshatch Patterns fill the screen with a grid and a series of dots. Crosshatch Patterns help you to check or adjust several monitor parameters: These include convergence, linearity, active viewing area and dynamic focus. The grid and the dots should be all white in color, with no fringes or parallel images. The lines should be straight and the dots round. For more detail on these adjustments, consult service literature from the monitor manufacturer. Color Screen tests fill the screen with 100% of the chosen color at normal intensity. The Color Screen tests help you to check or adjust monitor intensity, black level, blanking and color purity. Each screen should be absolutely uniform from top to bottom and side to side. No retrace lines or noise should be visible. Color Screens may not hold their uniformity if the monitor degaussing circuit is defective. White, Gray and Black Screens fill the screen with black, gray or white at various intensities. These monochrome screens help you to check or adjust monitor convergence, purity, contrast and intensity. These screens also simplify black level and color gun control settings. The screens should be uniform with no color tints or distortion. No retrace lines or noise should be visible. If tests indicate a need for adjustment, use the controls on the Monitor Remote Adjustment Board.

3-5

Page 25

Main Menu (continued) Diagnostics Menu (continued) System Information Screen

SYSTEM INFORMATION SCREEN Select SYSTEM INFO at the Diagnostics Menu. The System Information Screen provides the current version numbers of this game’s hardware and software. Use these numbers to describe the system during parts replacement, service calls, etc.

SYSTEM INFORMATION

MIDWAY GAMES, INC. XXXXXXX SYSTEM

SERIAL NUMBER: XXXXXXXXX

GAME: XXXXXXXXXX

DATE OF MANUFACTURE: XX/XX/XX

PRESS ANY BUTTON TO EXIT

SYSTEM INFORMATION SCREEN

The System Information screen reports information, but doesn’t permit you to make changes. The Title line identifies the manufacturer of this game and the electronic board set used in this product. The Serial Number, Game and Date of Manufacture identify the game name and production run.

3-6

Page 26

Main Menu (continued) Diagnostics Menu (continued) Sound Subsystem Test Menu

SOUND SUBSYSTEM TEST MENU

Select SOUND SUBSYSTEM at the Diagnostics Menu. Sound Subsystem Tests verify that audio components are connected and operate properly. Highlight an option with any player panel joystick. Select the option with any player panel button.

SOUND SUBSYSTEM TEST

BOOT VERSION: XX.XX

SDRC VERSION: XX.XX

PORT STATUS: GOOD

CHECKSUM: XXXX

SRAM: OK

DRAM: OK

TONE STATUS: GOOD

OS VERSION: XX.XX

PRESS ANY BUTTON TO EXIT

SOUND SUBSYSTEM MENU

Version, Status, Checksum and RAM Reports are diagnostic routines. These routines analyze the digital sound circuits and can detect sound memory problems. Test results appear as numbers or messages. Sounds may also accompany some tests. Reports other than GOOD or OK indicate a problem.

3-7

Page 27

Main Menu (continued) Diagnostics Menu (continued) Disk Tests Menu

DISK TESTS Select DISK TESTS at the Diagnostics Menu. Disk Tests allow you to verify proper operation of the hard disk drive assembly. Highlight an option with any player panel joystick. Select the option with any player panel button.

DISK TESTS

DISK INFORMATION

SEQUENTIAL READ

SEQUENTIAL CACHE READ RANDOM READ

RANDOM CACHE READ

DATA INTEGRITY TEST

FILE SYSTEM CHECK

SURFACE SCAN

EXIT

DISK TESTS MENU

Disk Information. The Disk Information routine verifies the interface between the CPU Board Assembly and hard disk drive. The processor requests disk information. Data cannot be retrieved successfully if there is a problem. Sequential Disk Read. This routine tries to access every bit of data in the order it is stored directly on the disk. The hard disk drive media may be defective if this routine cannot be completed successfully. Sequential Cache Read. This routine tries to access every bit of data in the order it is stored in the temporary disk memory cache. If this test is not successful, the memory circuits may be faulty. Random Disk Read. This routine tries to access every bit of data in no particular order directly from the disk. This test may detect problems with ability to position the drive heads accurately over the requested data. Random Cache Read. This routine tries to access every bit of data in no particular order from the temporary disk memory cache. If the cache fails this test, memory circuits may contain a fault. Data Integrity Test. This test analyzes the data on the disk drive. The test determines if corrupted data is on the disk. Bad data can cause the program to falter even though the hard disk operates correctly. File System Check. This routine performs a file-by-file check of the data stored on the hard disk. Surface Scan. The magnetic material on the disk can become damaged, causing data to be unreadable. This routine locates unusable areas on the disk and marks them for future reference.

3-8

Page 28

Main Menu (continued) Diagnostics Menu (continued) Switch Tests Menu

SWITCH TESTS MENU

Select SWITCH TESTS at the Diagnostics Menu. Switch Tests verify proper operation of the game’s switches, including buttons and joystick switches. Activate each switch, and the indicator on the screen changes state. Release the switch and the indicator returns to its previous, normally open or closed condition. You can test any combination of switches together. To exit the test, simultaneously press the middle two control buttons inside the coin door. The Switch Test Screen refers to these buttons as “volume buttons.”

PLAYER SWITCH INPUTS TEST

P3UPLEFT COIN
P3DOWNRIGHT COIN
P3LEFTP1 START
P3RIGHTSLAMITILT
P3JUMPTEST
P3PASSP2 START
P3TURBOSERVICE CREDIT

CENTER COIN

P4UPEXTRA COIN
P4DOWNP3 START
P4LEFTP4 START
P4RIGHTVOLUME DOWN
P4JUMPVOLUME UP

P4 PASS P4 TURBO UP DOWN LEFT RIGHT JUMP PASS TURBO

UP DOWN LEFT RIGHT JUMP PASS TURBO BILL VALID.

P4149 WAY P2 49 WAY P3 49 WAY P4 49 WAY 24 24 24 24

PRESS BOTH PLAYER 1 AND PLAYER 2 START BUTTONS TO EXIT

SWITCH TEST SCREEN

Switches appear on the screen as colored boxes. Red boxes indicate an open state. Green indicates closed. Any other color indicates a fault condition. A single indication on the menu screen should exactly duplicate a button or joystick change. You'll notice a unique number for a switch recognized by game electronics.

Use Switch Tests to locate crossed wires, intermittent conditions and stuck switches.

NOTICE: Some switches may not be used with this game. If you can’t find one of the listed switches, check the wiring diagram.

3-9

Page 29

Main Menu (continued) Diagnostics Menu (continued) DIP-Switch Tests Menu

DIP-SWITCH TESTS MENU Select DIP-SWITCH TESTS at the Diagnostics Menu. Two 8-position DIP switch banks reside on the SIO Board. DIP-Switch Tests allow you to check the position of the 16 switches in these banks. You can change the setting of any DIP switch without removing the circuit board cage. The screen displays an illustration of each switch block and the current settings. You can change DIPswitch positions with power on. Set any switch, and then check the screen to verify that the new setting is enabled. Refer to the charts for assistance in choosing switch positions. (* indicates factory defaults.) To exit the DIP-switch Test, press the left control button (inside the coin door). Attract Mode-Selection Switch. You can change which Attract Mode sequence the game displays. Select NBA Showtime or NFL Blitz by flipping switch 8 at DIP bank U13. Then power down and up again. Players can still play either game. DIP Switch 1 (U13) Swi | Sw2 | Sw3 | Sw4 | Sw5 | Swe | Sw7 | SW8 Coinage Control DIP Switch Off

CMOS, On*

USA1 Gert FrECA1 UK1 Off* | Off* | Off*

USA2 Ger2 FrECA2 UK2OnOffOff
USA3 Ger3 FrECA3 UK3OffOnOff
USA4 Ger4 FrECA4 UK4OnOnOff
USAS Ger5 FrECAS UK5OffOffOn
USAQ Ger9 FrECA9 UK9OnOffOn
USA10 Ger10 Fr ECA10 UK ECAOffOnOn
USA ECA / Ger ECA / Fr ECA8OnOnOn
Free Play (All Countries)OnOnOn

Country USA Off* Off*

France On Off

Germany Off On

UK** On On Unused ~ Off* = On Game NBA Showtime Off* NEL Blitz On **Except Free Play, which is “on” for SW2 through SW6.

DIP Switch 2 (U12) Swi | Sw2 | Sw3 | Sw4 | Sw5 | Sw6 | Sw7 | Sw8 Joystick Type 8-Way Off 49-Way On*

Monitor ResolutionMedium ResOff*

Low Res On

Unused-Off*

= On

Unused-Off*

= On

Unused-Off*

= On Player Panel Type = 2-Player Off 4-Player On*

Power Up Test Active Off

Inactive On*

Operating Mode Game Mode Off* Test Mode On

Page 30

Main Menu (continued) Diagnostics Menu (continued) Speaker Test Menu

SPEAKER TEST MENU Select SPEAKER TEST at the Diagnostics Menu. The Speaker Test provides audio signals to test the loudspeakers. Use tests on the Speaker Test menu to verify operation of audio system components. Highlight an option with any player panel joystick. Select the option with any player panel button.

SPEAKER TESTS

LEFT CHANNEL

CENTER CHANNEL

RIGHT CHANNEL

100 HZ TONE

1 KHZ TONE

PLAY TUNE

EXIT

SPEAKER TEST MENU

Channel and Tone Tests. The channel subtests employ voice announcements to verify speaker locations. Use the 100 Hz tone to check the speakers’ bass response. Small speakers with weak magnets or poor baffles may cause poor bass response. Play Tune repeats a series of game sounds. Use PLAY TUNE to check speaker operation and fidelity. If your game has stereo speakers, run PLAY TUNE and test speaker phasing. Muddy, weak or distorted sound during this test may indicate crossed wires or out-of-phase speaker connections. Missing sounds may indicate audio cabling errors.

increase the volume level. Before returning to Game-Over Mode, reset the volume ( ) NOTICE: Check the volume setting before testing. To test the speakers thoroughly, level to its original setting.

Page 31

Main Menu (continued) Audits Menu

AUDITS MENU Select AUDITS at the Main Menu. The Audits menus permit you to review game play statistics. Additional menus give detailed reports for each player position on game starts, ends, cabinet abuse, fault conditions, etc. Highlight an option with any player panel joystick. Select the option with any player panel button. The screen displays a list of the statistics available to you. Select an item to view the detailed report. AUDITS

COIN AUDITS

CREDITS AUDITS

GAME AUDITS

TEAM STATS

OFFENSIVE PLAYS

DEFENSIVE PLAYS

EXCEPTION DUMP

CLEAR AUDITS

EXIT

AUDITS MENU

Data in the Audits menus helps you to keep records of the game’s popularity and earning potential. Use the highlight bar to select the desired subject on the Audits Menu. Each entry on the Audits Menu is the subject for an entire screen of bookkeeping information. On these screens, you can track favorite teams, frequently used offensive and defensive plays, etc. Some audits menus also include histograms. Histogram screens allow graphical analysis of statistics. This permits visual comparisons between games. Histograms have no bar graphs until the system acquires enough data to plot. Examine and record all game audit values before performing game service or repairs.

NOTICE: Be careful when clearing audit information. Once you clear data, you cannot restore it.

3-12

Page 32

Main Menu (continued) Audits Menu (continued) Coin Audits Screen

COIN AUDITS SCREEN

Select COIN AUDITS at the Audits Menu. The Coin Audits Screen permits you to assess the currency collection. This report screen presents revenue quantities and other important game statistics. Coin Audits is a read-only screen. To exit, press any player panel button.

COIN AUDITS - PAGE: 1

LEFT SLOT COINS XXXXXXXX

RIGHT SLOT COINS XXXXXXXX

BILLS XXXXXXXX

CENTER SLOT COINS XXXXXXXX

EXTRA SLOT COINS XXXXXXXX

GAME STARTS XXXXXXXX

MID-GAME STARTS XXXXXXXX

CONTINUES XXXXXXXX

FREE QUARTERS XXXXXXXX

AWARDED XXXXXXXX

SERVICE CREDITS XXXXXXXX

TOTAL PLAYS XXXXXXXX

UP - NEXT / BUTTON - EXIT

COIN AUDITS SCREEN, PAGE 1

The Coin Audits screen reports total quantities of coins, bills or credits collected by each active device. The screen doesn’t calculate the value of the collected currency.

This screen reports information, but doesn’t permit you to make changes. To reset the coin, bill and credit counters to zero, use the Clear Audits menu.

We recommend that you examine and record audit information before you make changes. Once you’ve cleared the counters, you can’t retrieve the previous data from the system.

COIN AUDITS — PAGE: 2

TOTAL PAID CREDITS XXXXXXXX

TOTAL XXXXXXXX

DOWN - PREV/ BUTTON - EXIT

COIN AUDITS SCREEN, PAGE 2

Page 33

Main Menu (continued) Audits Menu (continued) Credits Audits Screen

CREDITS AUDITS SCREEN

Select CREDITS AUDITS at the Audits Menu. The Credits Audits Screen permits you to assess the currency collection. This report screen presents revenue quantities and other important game statistics. Credits Audits is a read-only screen. To exit, press any player panel button.

CREDITS AUDITS - PAGE: 1

CREDITS AVAILABLE XXXXXXXX

PRESS ANY BUTTON TO EXIT

CREDITS AUDITS SCREEN

3-14

Page 34

Main Menu (continued) Audits Menu (continued) Game Audits Screen

GAME AUDITS

Select GAME AUDITS at the Audits Menu. The Game Audits Screen permits you to review the game play statistics. Game Audits is a read-only screen. To exit, press any player panel button.

GAME AUDITS - PAGE: 1

TOTAL UPTIME TOTAL PLAY TIME GAME STARTED INITIALS ENTERED <FG> PURCHASED AT START CREATE PLAY SESSIONS 1 PLAYER 2 PLAYER 3 PLAYER 4PLAYER 2PV CPU 1 QUARTER GAMES 2 QUARTER GAMES 3 QUARTER GAMES 4 QUARTER GAMES WENT INTO OVERTIME 1 WENT INTO OVERTIME 2 WENT INTO OVERTIME 3 1 PLAYER FINISHES 2 PLAYER FINISHES 3 PLAYER FINISHES 4 PLAYER FINISHES 2P V CPU FINISHES HVS H LSW’S CPU WINS (FG) AVG H VS H TOTAL SCORE (FG) AVG H VS CPU TOTAL SCORE (FG)

AVG H VS H WIN SCORE (FG)

35S 5S SESE

UP — NEXT / BUTTON - EXIT

GAME AUDITS SCREEN, PAGE 1

The Game Audits screen reports information, but doesn’t permit you to make changes. Examine and record information at GAME AUDITS before deleting data at the Clear Audits Menu. Once you've cleared the counters, you can’t retrieve the previous data from the system. GAME AUDIT MENU TERMS

SCREEN DEFINITION SCREEN DEFINITION

TERM TERM

AVGAverageLswYourgamecomputer's _ internal

record-keeping counters CPU Central Processing Unit: The game

computerMachineNumber of power cycles (game turn-

Power-On ons) <FG>, (FG) | Full Game oT Overtime HVS CPU | Human versus CPU: Competition that

pits players against the game computerPVPlayer versus...

HVSH Human versus human: Competition | Total Uptime | Overall on-time for the game between human players computer

2PV Two players versus...

Page 35

GAME AUDITS - PAGE: 2

AVG H VS H LOSS SCORE

(FG) BIGGEST CPU WIN MARGIN (fg) BIGGEST CPU LOSS MARGIN (fg) TLF’S SBLF’S 35S SESE SESE HER

DOWN - PREV/ BUTTON - EXIT

GAME AUDITS SCREEN, PAGE 2

Page 36

Main Menu (continued) Audits Menu (continued) Team Stats Screen

TEAM STATS

Select TEAM STATS at the Audits Menu. Team Stats details the number of games played by each team in the league. Team Stats is a read-only screen. To exit, press any player panel button.

TEAM STATS - PAGE: 1

ARIZONA CARDINALS 0 MINNESOTA VIKINGS

ATLANTA FALCONS NEW ENGLAND PATRIOTS

BALTIMORE RAVENS NEW ORLEANS SAINTS

BUFFALO BILLS NEW YORK GIANTS

CAROLINA PANTHERS. NEW YORK JETS

CHICAGO BEARS OAKLAND RAIDERS

CINCINNATI BENGALS PHILADELPHIA EAGLES

CLEVELAND BROWNS PITTSBURCH STEELERS

SAN FRANCISCO

SEATTLE SEAHAWKS,

ST. LOUIS RAMS

TAMPA BAY BUCS

TENNESSEE TITANS

WASHINGTON REDSKINS DENVER BRONCOS

DETROIT LIONS

GREEN BAY PACKERS

INDIANAPOLIS COLTS

JACKSONVILLE JAGUARS

KANSAS CITY CHIEFS

MIAMI DOLPHINS DALLAS COWBOYS 0 SAN DIEGO CHARGERS

PRESS ANY BUTTON TO EXIT

TEAM STATS SCREEN

Page 37

Main Menu (continued) Audits Menu (continued) Offensive Plays Screen

OFFENSIVE PLAYS SCREEN

Select OFFENSIVE PLAYS at the Audits Menu. Offensive Plays accounts for each play type as a percentage of all offensive plays. Offensive Plays is a read-only screen. To exit, press any player panel button.

OFFENSIVE PLAYS -— PAGE: 1

UPPER CUT0%REVERSE ZIP
BLIZZARD0%SWEEP R/L
HAIL MARY0%MIDDLE PICK

TURMOIL 0% DA BOMB

BACK SPLIT0%UTB DEEP
CRISS CROSS0%SUB ZERO
DAWG HOOK0%SUPER FLY

UP THE GUT 0%

SCREEN 0%

FIELD GOAL 0%

FAKE FG 0%

EXTRA POINT 0%

PUNT 0%

FAKE PUNT 0%

HB BLOCK 0%

SLANT RIL 0%

PRESS ANY BUTTON TO EXIT

OFFENSIVE PLAYS SCREEN

Page 38

Main Menu (continued) Audits Menu (continued) Defensive Plays Screen

DEFENSIVE PLAYS SCREEN

Select DEFENSIVE PLAYS at the Audits Menu. Defensive Plays accounts for each play type as a percentage of all defensive plays. Defensive Plays is a read-only screen. To exit, press any player panel button.

DEFENSIVE PLAYS - PAGE: 1

SAFE COVER 0%

GOAL LINE 0%

2 MAN BLITZ 0%

MEDIUM ZONE 0%

SUICIDE BLITZ 0%

DEEP ZONE 0%

1 MAN BLITZ 0%

NEAR ZONE 0%

ZONE BLITZ 0%

BLOCK FG 0%

BLOCK PUNT 0%

PUNT RETURN 0%

PRESS ANY BUTTON TO EXIT

DEFENSIVE PLAYS SCREEN

Page 39

Main Menu (continued) Audits Menu (continued) Exception Dump Screen

EXCEPTION DUMP SCREEN

Select EXCEPTION DUMP at the Audits Menu. Game programmers use the Exception Dump Screen to view register contents during program development. This screen has no field purpose. Exception Dump is a read-only screen. To exit, press any player panel button.

Main Menu (continued) Audits Menu (continued) Clear Audits Menu

CLEAR AUDITS

Select CLEAR AUDITS at the Audits Menu. The Clear Audits menu allows you to clear individual memory counters or to reset them all at once.

Highlight an option with any player panel joystick. Select the option with any player panel button.

CLEAR AUDITS

CLEAR COIN AUDITS

CLEAR CREDIT AUDITS

CLEAR GAME AUDITS

CLEAR TEAM STATS

CLEAR OFFENSIVE PLAYS

CLEAR DEFENSIVE PLAYS

CLEAR EXCEPTION DUMP

CLEAR ALL

EXIT

CLEAR AUDITS MENU

You can reset any audit screen from the Clear Audits Menu. Choose an item and zero its counter. CLEAR ALL simultaneously changes all audit categories to factory default values. After you've selected an item, the system gives you the opportunity to escape this change. For example:

ARE YOU SURE YOU WANT TO CLEAR COIN AUDITS?

LAST CHANCE MENU

After you've selected and verified a clear function, the values reset. The system can’t restore the previous values. Examine and record utility values before you make changes.

3-20

Page 40

Main Menu (continued) Adjustments Menu

ADJUSTMENTS MENU Select ADJUSTMENTS at the Main Menu. The Adjustments menus permit you to change game characteristics. Use these screens to optimize game performance and earnings. Highlight an option with any player panel joystick. Select the option with any player panel button.

ADJUSTMENTS

PRICING

FREE PLAY

ATTRACT SOUND

ADDITIONAL ADJUSTMENTS

FULL FACTORY RESTORE

EXIT

ADJUSTMENTS MENU

Main Menu (continued) Adjustments Menu (continued) Pricing Menu

PRICING MENU

Select PRICING at the Adjustments Menu. The Pricing menus allow you to view current settings or change the cost of games. Custom pricing allows you to select the number of coins or credits required for each game. The game restores factory default values if you exchange the CPU Board or if the backup battery fails. Highlight an option with any player panel joystick. Select the option with any player panel button. You may reset options to factory defaults or change an option after viewing it. We recommend examining and recording pricing options before making changes. You may save several custom prices and then choose between them as needed. On-screen instructions guide you through the process of creating custom price settings.

PRICING

SHOW CURRENT NORTH AMERICA SOUTH AMERICA EUROPE (A-G) EUROPE (H-Z) ASIA AUSTRALIA ISTOM PRICING EXIT

PRICING MENU

An additional box appears on screen to explain the available functions as you select each item.

3-21

Page 41

STANDARD PRICING TABLE

NAMESTARTCONTINUE | CREDITS/COINCOINT | COIN2 | COIN3 | COIN4 | BILL
ANTILLES22:1/25¢, 4G.25¢1G
AUSTRALIA 122113X20¢, 2/$1.0020¢$1.00
AUSTRALIA 2221/5X20¢, 1/$1.0020¢$1.00
‘AUSTRIA 122Sch, 2/10Sch5 Sch | 10Sch
AUSTRIA 2224/2X5Sch, 3/2X10Sch5Sch | 10Sch
BELGIUM 1221720BF20BF20BF
BELGIUM 2223/20BF20BF20BF
BELGIUM 3222/20BF20BF20BF
BELGIUM ECA221/20BF50BF20BF5BF
CANADA 122172 x 25¢, 3/$125¢25¢
CANADA 2221/2x 25¢,3/$125¢$1.00
CANADA 3223/ $1.00, 6 / $2.00$1.00| $2.00
CANADA ECA221/2x25¢,3/$125¢$1.00 | $2.00
DENMARK22‘3/SDKr, 7/10DKr‘SDKr4ODKr
FINLAND.2241 FmktFmk__|5¢mk
FRANCE 1222/5Fr, S/10FrSFr10Fr
FRANCE 2212I5Fr, 4/10FrSFr10Fr
FRANCE 3214/5Fr, 3/10FrSFr10Fr
FRANCE 4214/5Fr, 20FrSFr10Fr
FRANCE 5212I5Fr, S/10Fr, 11/2 X 10FrSFr10Fr
FRANCE 6212I5Fr, 4/10Fr, 9/2 X 10FrSFr10Fr
FRANCE 7214/5Fr, 3/10Fr, 7/2 X 10FrSFr10Fr
FRANCE 8214/5Fr, 2/10Fr, 5/2 X 10FrSFr10Fr
FRANCE 921413 X 1Fr, 2/5Fr1FrSFr
FRANCE 1021112 X 1Fr, 3/5Fr1FrSFr
FRANCE 1121413 X Fr, 2/5Fr, 5/2 X SFr4FrSFr
FRANCE 12211/2 X 1Fr, 3/5Fr, 7/2 X SFr4FrSFr
FRANCE ECA 111215Fr, S/10Fr1FrSFr10Fr20Fr
FRANCE ECA 2112I5Fr, 4/10Fr4FrSFr10Fr20Fr
FRANCE ECA 3114/5Fr, 3/10Fr4FrSFr10Fr20Fr
FRANCE ECA 4114/5Fr, 20Fr4FrSFr10Fr20Fr
FRANCE ECA 5112I5Fr, S/10Fr, 11/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 6112I5Fr, 4/10F r, 9/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 7114/5Fr, 3/10Fr, 7/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 8114/5Fr, 2/10Fr, 5/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 911413 X 1Fr, 2/5Fr1FrSFr10Fr20Fr
FRANCE ECA 10| 41112 X 1Fr, 3/5Fr1FrSFr10Fr20Fr
FRANCE ECA 11| 41413 X 1Fr, 2/5Fr, 5/10Fr1FrSFr10Fr20Fr
FRANCE ECA 12 | 11412 X 1 r, 3/5Fr, 7/10Fr1FrSFr10Fr20Fr
FRANCE ECA 13| 414M 0F r, 2/20Fr, 4/30Fr1FrSFr10Fr20Fr
FREE PLAY===NoneNoneNoneNoneNone
GERMANY 122771M, 6/5DM7DMSDM
GERMANY 22141M, 7/5DM1DM5DM
GERMANY 3214/1DM, 8/5DM1DM5DM
GERMANY 4214/1DM, 5/5DM1DM5DM
GERMANY 5214/1DM, 6/5DM1DM5DM
GERMANY ECA1 | 224/1DM, 2/2DM, 6/5DM1DM20M5DM
GERMANY ECA2 | 2141M, 2/2DM, 6/5DM1DM20M5DM
GERMANY ECA3_|414/1DM, 2/2DM, 6/5DM1DM20M5DM
HUNGARY,222X1 0F t, 3/2X20Ft40Ft20Ft
ITALY,224/500L1tS00LIt__|SOOLIt
‘JAPAN 1227/100Yen100100
JAPAN 2222/100Yen100100
NETHERLANDS224MHFI, 3/2.5HFI4HFI2.5HFI
NEW ZEALAND 1 | 71111$1$2
NEW ZEALAND 2 | 112181$1$2
NORWAY.22BISNKr, 6/10NKrSNKrTONKr
SPAIN 1221/100Pta, 6/500Pta100Pta | 500Pta
SPAIN 2221/100Pta, 5/500Pta100Pta_|500Pta
‘SWEDEN,2243X18Kr, 2/5SKrTSKr5SKr
SWITZERLAND T | 224/1SFr, 6/5SFr1SFrSSFr
SWITZERLAND 2 | 224/4SFr, 7/5SFr1SFr5SFr
SWITZERLAND 3__|224/4 SFr, 8/5SFr1SFr5SFr

(Table continues on next page)

3-22

Page 42

STANDARD PRICING TABLE, continued

NAMESTARTCONTINUE | CREDITS/COINCOINT [ COIN2[COINS [ COIN4 | BILL
UKECA4111150p, 3/£1.00£1.00 | 50p20p10p£2.00
UK ECA2111150p, 2/81.00£1.00| 50p20p10p£2.00
UKECA3111730p, 2/50p, 5/£1.00£1.00 | 50p20p0p£2.00
UK4111150p, 3/£1.00£1.00 | 50p
UKS:111150p, 2/81.00£1.00 | 50p
UK ECA6111130p, 2/50p, 4/£1.00£1.00| 50p20p0p£2.00
UK ECAT113/81.00£1.00 | 50p20p10p£2.00
UKECA8111150p, 2/81.00, 4162.00£1.00 | 0p20p10p£2.00
USAT221125¢25¢25¢$1.00
USsA2211125¢25¢25¢$1.00
USA3111125¢25¢25¢$1.00
usaA4111150¢, 3/$1.0025¢25¢$1.00
USAS211150¢, 4/$1.0025¢25¢$1.00
USA6111150¢25¢25¢$1.00
USA7111150¢, 3/$1.0025¢25¢$1.00
USAB221150¢, 4/$1.0025¢25¢$1.00
usag321125¢, 4/$1.0025¢25¢$1.00
USA10331125¢, 4/$1.0025¢25¢$1.00
USsA11421125¢, 4/$1.0025¢25¢$1.00
USA12431125¢, 4/$1.0025¢25¢$1.00
USA13441125¢, 4/$1.0025¢25¢$1.00
USAECA331125¢, 4/$1.00$1.00 | 25¢10¢o5¢$1.00

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Current Pricing Screen

Current Pricing Screen

Select SHOW CURRENT at the Pricing Menu. The Current Pricing Screen is a read-only screen. Use it to check pricing parameters for the pricing table your game is using. To select a new pricing table, return to the Pricing Menu. To invent your own pricing table, select Custom Pricing on the Pricing Menu. Press any player panel button to exit.

CURRENT PRICING

LEFT SLOT UNITS

RIGHT SLOT UNITS

CENTER SLOT UNITS

EXTRA SLOT UNITS

BILL VALIDATOR UNITS

UNITS PER CREDIT

UNITS PER BONUS

MINIMUM UNITS

CREDITS TO START

CREDITS TO CONTINUE

MAX CREDITS

COINS PER BILL

PRESS ANY BUTTON TO EXIT

CURRENT PRICING SCREEN

3-23

Page 43

The following table clarifies Pricing Menu terms: SCREEN TERM DISCUSSION Slot Units: Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism : es or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins Bill Validator (DBV) ; A Units per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit.

Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits. Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept.

Coins per Bill How many coins one bill is worth.

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu

Custom Pricing

Select CUSTOM PRICING at the Pricing Menu. The Custom Pricing Menu permits you to program and use your own pricing table. You can save several pricing schemes and chose between them as desired. Highlight an option with any player panel joystick. Change the option with any player panel button. Press any START button to save your pricing table and exit from the menu.

CUSTOM PRICING

ADD

DELETE

EDIT

DELETE ALL

SELECT

EXIT

CUSTOM PRICING OPENING MENU

Add allows you to write a new custom pricing scheme. If you choose ADD, the system directs you to... [] 1. Name your scheme. [] 2. Program pricing information. [] 3. Select the coin denomination for your scheme. [] 4. Compose a pricing screen message. Delete permits you to eliminate a single custom pricing scheme. Edit lets you modify a stored custom pricing scheme. Delete, when enabled, clears all custom pricing schemes. Select enables you to choose which custom pricing scheme is the active one.

3-24

Page 44

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Creating Pricing Scheme Menu

Creating Pricing Scheme Menu

After you name your custom pricing scheme, you encounter the Creating Pricing Scheme Menu. This menu is where you program the pricing scheme. You can save several pricing schemes and chose between them as desired. Highlight an option with any player panel joystick. Select Change Mode with with any player panel button. Use a joystick to change the option. Save your setting by pressing any player panel button. Press any START button to save your pricing table and exit from the menu.

CREATING XXXX

LEFT UNITS RIGHT UNITS

CENTER UNITS EXTRA UNITS

DBV UNITS UNITS PER CREDIT

UNITS / BONUS. MINIMUM UNITS

CREDITS TO START CREDITS TO CONT.

MAX CREDITS COINS / BILL

SHOW FRACTIONS LEFT COUNT

RIGHT COUNT CENTER COUNT

EXTRA COUNT DBV COUNT

USE STICK TO SELECT AN ITEM TO MODIFY

PRESS ANY BUTTON TO MODIFY THE ITEM

PRESS ANY START BUTTON TO SAVE AND EXIT

CUSTOM PRICING MENU

The Custom Pricing Menu employs the same terms that appear on the Current Pricing Table. See the table below for definitions of these terms.

PRICING MENU TERMS SCREEN TERM DISCUSSION Slot Units: Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism : + or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins Bill Validator (DBV) Units per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit.

Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits. Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept.

Coins per Bill How many coins one bill is worth.

3-25

Page 45

BASIC CUSTOM PRICING. Custom pricing creates an imaginary currency exchange. In this currency exchange, the coins of the realm are “units.” Think of units as a type of cyber-currency, useful only within the game software. By inserting coins, you purchase units. Since units are only negotiable within game software, the system stores your units for you. When the system receives enough units, it buys a game for you. The price of a game is one “credit.” You can think of credits as a second form of cyber-currency. Even though you’ve now bought one game, you may not be able to begin playing. In many pricing schemes, you must buy two or more credits to begin play. The idea here is something like a minimum order of goods at a store. That is, the operator can “shrink-wrap” two or more games in a package. You can’t play unless you buy the entire package. 1 / 25¢ COIN; 1 CREDIT TO START. In a simple, quarter pricing scheme, the player inserts one coin to buy one unit. The system exchanges that unit for one credit. If CREDITS TO START contains the value one, then play commences. A dollar bill buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14114

e1 / 3 X 25¢; 2 CREDITS TO START. Again, assuming quarter slots, here’s one way to implement 75¢ pricing... In this scheme, each coin that the player inserts buys one unit. The system exchanges three units for one credit. CREDITS TO START contains the value two. To play, the player must pay for two credits. In this scheme, a dollar buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14324

e2 / 1 COIN; 6 CREDITS TO START. Now let's consider a more unusual pricing scheme. Here, the player can buy two units with one coin. The system exchanges each of these units for one credit. Notice that CREDITS TO START contains the value six. To play, the player must insert two more coins to pay for six credits. Also notice that if the player pays with a bill, the system throws in an extra unit.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
29464

3-26

Page 46

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu (continued) Screen Message Menu

Screen Message Menu Towards the end of the Custom Pricing Menus, you encounter the Screen Message Menu. The Screen Message Menu allows you to enter a brief pricing or advertising message. The video game machine displays your message during the Attract Mode. You may enter one or two lines of text. Each line may include up to 32 alphanumeric characters. Here’s an example of a typical message... 1 CREDIT / 2 COINS EAT AT JOE’S

Highlight a letter with any player panel joystick. Select the letter with any player panel button. Delete the rightmost character of the default message by selecting the on-screen asterisk (*). Watch the bottom of the screen to see your message line develop. Save the entire line and proceed to the second line by selecting the arrow (>).

PRICING — LINE 1

1 CREDIT / 2 COINS

USE STICK TO MOVE / BUTTON TO SELECT

SCREEN MESSAGE MENU

After you complete your message, you may edit it by reentering the Screen Message Menu. To reenter the menu, choose EDIT from the Custom Pricing Menu.

3-27

Page 47

Main Menu (continued) Adjustments Menu (continued) Free Play Menu

Free Play Menu Select FREE PLAY at the Adjustments Menu. Free play is a useful feature for promotions and long-term testing under play conditions. Enable free play to allow players to play the game without inserting currency. Disable free play to sell games. Highlight an option with any player panel joystick. Select the option with any player panel button.

Main Menu (continued) Adjustments Menu (continued) Attract Sound Menu

Attract Sound Select ATTRACT SOUND at the Adjustments Menu. The Attract Mode operates between games. It attempts to lure prospective players into trying your game. Attract Mode sound may not be appropriate for some locations. The Attract Sound Menu allows you to enable or disable the Attract Mode sound feature. You can turn Attract Mode sound on or off without changing the game volume level. Highlight an option with any player panel joystick. Select the option with any player panel button.

ENABLE ATTRACT MODE SOUNDS?

ATTRACT SOUND MENU

3-28

Page 48

Main Menu (continued) Adjustments Menu (continued) Additional Adjustments Menu

ADDITIONAL ADJUSTMENTS MENU Select ADDITIONAL ADJUSTMENTS at the Adjustments Menu. Additional Adjustments menu items allow you to set the game to match player requirements. These adjustments affect speed, challenge, rewards, etc. that determine player enjoyment. Highlight an option with any player panel joystick. Select the option with any player panel button.

ADDITIONAL ADJUSTMENTS

GAME DIFFICULTY

DISCOUNT PRICE / CREDITS

CLOCK SPEED

FREE GAME - FULL 4 PLR.

FREE GAME - FULL 1 ON 1

FREE GAME - FULL V. CPU

FREE QUARTER - 4 PLR. FREE QUARTER - 1 ON 1

FREE QUARTER - V. CPU VIOLENCE

BAD LANGUAGE

CLEAR PLAYER RECORDS

TOURNAMENT MODE

ATTRACT MOVIE SOUND

EXIT

ADDITIONAL ADJUSTMENTS MENU

Game Difficulty allows you to alter the challenge that a game poses to players. Choose the level that most closely matches the players’ skills. Discount Price / Credits adjusts the quantity of buy-in points to encourage multiple game purchases. Clock Speed alters how much game time that a player can purchase for one credit. Choose one of these settings: Extra slow, slow, medium, fast or extra fast. Operator Message. Enter your own, custom message at this menu. Program the message to turn on at the appropriate day and time. Free Games and Free Quarters. Use these features to provide incentives to good players. Violence. You can remove violence from the game without affecting other game play characteristics. Bad Language. You can remove rough language without affecting other game play characteristics. Clear Player Records allows you to delete stored game play data. Tournament Mode, when enabled, adapts your game’s scoring for tournament-style play. Attract Movie Sound, when enabled, allows Attract Mode movie sound with Attract Mode sound off. The Attract Mode movie is only one component of the Attract Mode graphics.

3-29

Page 49

Main Menu (continued) Adjustments Menu (continued) Full Factory Restore Menu

FULL FACTORY RESTORE MENU Select FULL FACTORY RESTORE at the Adjustments Menu. The Full Factory Restore menu allows you to clear all memory counters at once. Highlight an option with any player panel joystick. Select the option with any player panel button.

RESTORE ADJUSTMENTS & AUDITS?

FULL FACTORY RESTORE MENU

NOTICE: Examine and record audit information before you make changes. Once you've cleared the counters, you can’t retrieve previous data from the system.

Examine and record utility values before you make changes. If you choose YES, the system restores all adjustments and audits to factory default values. This change isn’t reversible. The system can’t restore the previous values. With the settings restored, the system displays the Reset CompletedScreen.

AUDITS & ADJUSTMENTS RESTORED

PRESS ANY BUTTON TO EXIT

RESET COMPLETED SCREEN

3-30

Page 50

Main Menu (continued) Volume Level Menu

VOLUME LEVEL Select VOLUME LEVEL at the Main Menu. Music plays continuously with the Volume Level Menu. Raise or lower the game’s sound level with any player panel joystick. (You can also use the volume up/down buttons on the diagnostic switch bracket.) Save your change and return to the Main Menu by pressing any player panel button.

SET VOLUME LEVI

A ——_ =—ti

UP / DOWN TO ADJUST VOLUME

PRESS ANY BUTTON TO SET VOLUME AND EXIT

VOLUME LEVEL MENU

Loud games attract more player interest than games with low-level sound. The Attract Mode sound level is lower than the game play sound level. You can turn Attract Mode sound on or off without changing the game volume level (see Adjustments).

NOTICE: These adjustments affect the volume of tests as well as of game play. If you set volume levels to minimum (zero), the speakers are silent during audio tests. We recommend setting volume levels to a moderately high value whenever you perform sound tests. After you complete tests, you may return sound levels to previous settings.

3-31

Page 51

Main Menu (continued) Utilities Menu

UTILITIES MENU Select UTILITIES at the Main Menu. Utilities Menu items allow you to clear bookkeeping totals. From the Utilities Menu, you can also restore game adjustments to factory settings. Highlight an option with any player panel joystick. Select the option with any player panel button.

UTILITIES

DUMP AUDITS CLEAR CREDITS CLEAR AUDITS RESET HIGH SCORES DEFAULT ADJUSTMENTS FULL FACTORY RESTORE

EXIT

UTILITIES MENU

Dump Audits allows you to send data to the game computer’s serial port. You can connect a serial printer to make a paper record of your audit data. Clear Credits opens a menu that allows you to zero the game’s credit data. Examine and record audit information before you make changes. Clear Audits opens a menu that allows you to zero the game’s audit data. Reset High Scores permits you to delete player names and scores that appear in the Attract Mode. This feature may be useful if players insert inappropriate language into the high score table. Default Adjustments opens a menu that allows you to reset game adjustments to factory settings. Full Factory Restore allows you to reset game adjustments and audits to factory settings.

NOTICE: Be careful when clearing audit information. Once you clear data, you can’t restore it.

3-32

Page 52

SPORTSTATION

CHAPTER

FOUR

DIAGNOSTIC, AUDIT & ADJUSTMENT MENU SYSTEM FOR NBA SHOWTIME GAMES

NOTICE: Information in this manual is subject to change without notice. Midway reserves the right to make improvements in equipment as progress in engineering warrants.

NOTICE: GAME-SELECTION SWITCH. Select NBA Showtime or NFL Blitz 2000 Gold Edition by flipping switch 8 at DIP bank U13. Then power down and up again. The Attract Mode for the game you select will appear. The player can still play either game.

Page 53

MENU SYSTEM

WHAT IS THE MENU SYSTEM? The game’s Menu System is a series of auditing, game adjustment and diagnostic screens. You can easily access and apply these screens to optimize game performance. For instance... e Use game audits screens to assess game performance. e Use adjustment screens to help you to customize game performance. For instance, you can restore factory default game settings. You can also calibrate player controls for accuracy. e Use diagnostic screens to verify proper equipment operation. ACTIVATING THE MENU SYSTEM Open the coin door. Find the TEST MODE switch inside. Press TEST MODE to invoke the Menu System. The game system responds by exiting Game Mode and entering Diagnostic Mode.

AUTOMATIC TESTS In Diagnostic Mode, the Power-On Self-Test (POST) activates. This routine runs automatically. It can detect faults that cause game or Menu System malfunctions. POST usually takes less than a minute. The test doesn’t display anything. Instead, the system boot loader indicates the software revision number and serial numbers. The system boot loader also displays a sound-loading message and other useful information. At the end of POST, the system displays the Control Functions Menu.

CONTROL FUNCTIONS The Control Functions Menu is purely informational. It appears for five seconds. Then the Menu System automatically displays the Dual Game Adjustment Menu. The Control Functions Menu introduces the menu navigation controls. The key point is that you can use either player or diagnostic controls to navigate menus. Diagnostic control switches are particularly helpful when you must troubleshoot player switches. This manual discusses the controls in more detail in this chapter’s Main Menu section. Also see the page on the menu that interests you.

STICK UP/VOLUME UP - MOVE UP

STICK DOWN/VOLUME DOWN - MOVE DOWN

STICK RIGHT — MOVE RIGHT

STICK LEFT - MOVE LEFT

PUSH BUTTON/TEST BUTTON - SELECT

5 SECONDS TO DIAG ENTRY

CONTROL FUNCTIONS MENU

4-2

Page 54

DUAL GAME ADJUSTMENT MENU

The Dual Game Adjustment Menu is another informational, read-only menu. It appears until you choose to exit. This menu reminds you that some NFL settings also affect NBA game play. Press any button to exit to the Main Menu.

ATTENTION!

ANY CHANGES TO THE FOLLOWING ADJUSTMENTS.

UPDATE BOTH NBA AND NFL

PRICING

FREE PLAY

VOLUME LEVEL

DISCOUNT PRICE / CREDITS

ATTRACT MODE SOUND ON / OFF

THIS ALSO INCLUDES DEFAULT ADJUSTMENTS.

AND

FULL FACTORY RESTORE FUNCTIONS.

PRESS ANY BUTTON TO EXI

DUAL GAME ADJUSTMENT MENU MAIN MENU

The Main Menu offers you access to the game machine’s test, bookkeeping and programmable features. Game audits, adjustments and diagnostics are line items on the Main Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.

NBA MAIN MENU

DIAGNOSTICS AUDITS ADJUSTMENTS VOLUME LEVEL ATTRACT VOLUME LEVEL UTILITIES NFL MAIN MENU EXIT TO NFL EXIT TO NBA

MAIN MENU MENU LAYOUT

Menus differ, but related information tends to occupy the same screen locations. e The block at the top, center of each screen displays the current menu title. e Data (menu items, video signals, statistics, reports, etc.) appears in the center of the screen. e Messages (explanations, control functions, revision levels) display at the bottom of the screen.

MENU NAVIGATION CONTROLS.

Use any player panel joystick to highlight a desired menu item. You can only select one highlighted item at a time. To select a highlighted item, press any player panel button. Operator control buttons inside the coin door serve as backup menu navigation controls. Press VOLUME UP or VOLUME DOWN buttons to highlight a menu item. Press TEST MODE to select a highlighted item.

EXIT OPTIONS

To exit the NBA menus and simultaneously enter the NFL menus, choose NFL MAIN MENU. To return the game to play, highlight either EXIT TO NFL or EXIT TO NBA. Your choice determines the game that will boot. Next, press any button.

4-3

Page 55

Main Menu (continued) Diagnostics Menu

DIAGNOSTICS MENU

Select DIAGNOSTICS at the Main Menu. Diagnostic tests allow you to verify the condition of the electrical and electronic hardware in the game.

Highlight a test with any player panel joystick. Select the option with any player panel button.

DIAGNOSTICS

MONITOR SETUP.

SYSTEM INFO

SOUND SUBSYSTEM

DISK TESTS

SWITCH TESTS

DIP-SWITCH TESTS

SPEAKER TEST

EXIT

DIAGNOSTICS MENU

Diagnostic tests assist you in checking and adjusting the game’s major systems. By running diagnostics, you can gain an insight into both system hardware and game software. Periodically running diagnostics is a crucial part of maintaining game performance and player satisfaction. Sometimes you can improve game performance by running a diagnostic test and making appropriate adjustments.

4-4

Page 56

Main Menu (continued) Diagnostics Menu (continued) Monitor Setup Menu

MONITOR SETUP MENU Select MONITOR SETUP at the Diagnostics Menu. The Monitor Patterns routine provides test screens to verify monitor performance or make adjustments. If tests indicate a need for adjustment, use controls on the Monitor Remote Adjustment Board. Highlight an option with any player panel joystick. Select the option with any player panel button. MONITOR SETUP.

COLOR BARS

CROSSHATCH

RED SCREEN

BLUE SCREEN

GREEN SCREEN

WHITE SCREEN

BLACK SCREEN

50 PCT. GRAY SCREEN

25 PCT. GRAY SCREEN

EXIT

MONITOR SETUP MENU

Color Bars fills the screen with colored stripes. Use the color bars to help you to check or adjust monitor brightness and contrast. The color bars also expose defects in horizontal linearity. Each color bar consists of 32 intensity levels. On a properly adjusted monitor, the top 31 of these levels are visible. Each bar should appear sharp, clear and distinct from bars on either side. Incorrect adjustment can cause missing detail at the top or bottom of a bar. Bent bars indicate horizontal linearity flaws, such as pie crust, pincushion or barrel distortion. (Correct color bar colors, left to right: Red, Green, Blue, Black, White, Cyan, Yellow, Violet.) Set controls as follows: 1. Adjust BRIGHTNESS and CONTRAST to minimum. 2. Turn up BRIGHTNESS until the pixels in the black stripe begin to glow (turn dark gray). 3. Bring up the CONTRAST control until you can see 31 bars. Crosshatch Patterns fill the screen with a grid and a series of dots. Crosshatch Patterns help you to check or adjust several monitor parameters: These include convergence, linearity, active viewing area and dynamic focus. The grid and the dots should be all white in color, with no fringes or parallel images. The lines should be straight and the dots round. For more detail on these adjustments, consult service piterature from the monitor manufacturer. Color Screen tests fill the screen with 100% of the chosen color at normal intensity. The Color Screen tests help you to check or adjust monitor intensity, black level, blanking and color purity. Each screen should be absolutely uniform from top to bottom and side to side. No retrace lines or noise should be visible. Color Screens may not hold their uniformity if the monitor degaussing circuit is defective. White, Gray and Black Screens fill the screen with black, gray or white at various intensities. These monochrome screens help you to check or adjust monitor convergence, purity, contrast and intensity. These screens also simplify black level and color gun control settings. The screens should be uniform with no color tints or distortion. No retrace lines or noise should be visible.

4-5

Page 57

Main Menu (continued) Diagnostics Menu (continued) System Information Screen

SYSTEM INFORMATION SCREEN Select SYSTEM INFO at the Diagnostics Menu. The System Information Screen provides the current version numbers of this game’s hardware and software. Use these numbers to describe the system during parts replacement, service calls, etc.

SYSTEM INFORMATION

MIDWAY GAMES, INC. XXXXXXX SYSTEM

SERIAL NUMBER: XXXXXXXXX

GAME: XXXXXXXXXX

DATE OF MANUFACTURE: XX/XX/XX

PRESS ANY BUTTON TO EXIT

SYSTEM INFORMATION MENU

The System Information screen reports information, but doesn’t permit you to make changes. The Title line identifies the manufacturer of this game and the electronic board set used in this product. The Serial Number, Game and Date of Manufacture identify the game name and production run.

4-6

Page 58

Main Menu (continued) Diagnostics Menu (continued) Sound Subsystem Test Menu

SOUND SUBSYSTEM TEST

Select SOUND SUBSYSTEM at the Diagnostics Menu. Sound Subsystem Tests verify that audio components are connected and operate properly. Highlight an option with any player panel joystick. Select the option with any player panel button.

SOUND SUBSYSTEM TEST

BOOT VERSION: XX.XX

SDRC VERSION: XX.XX

PORT STATUS: GOOD

CHECKSUM: XXXX

SRAM: OK

DRAM: OK

TONE STATUS: GOOD

OS VERSION: XX.XX

PRESS ANY BUTTON TO EXIT

SOUND SUBSYSTEM TEST MENU

Version, Status, Checksum and RAM Reports are diagnostic routines. These routines analyze the digital sound circuits and can detect sound memory problems. Test results appear as numbers or messages. Sounds may also accompany some tests. Reports other than GOOD or OK indicate a problem.

4-7

Page 59

Main Menu (continued) Diagnostics Menu (continued) Disk Tests Menu

DISK TESTS MENU Select DISK TESTS at the Diagnostics Menu. Disk Tests allow you to verify proper operation of the hard disk drive assembly. Highlight an option with any player panel joystick. Select the option with any player panel button.

DISK TESTS

DISK INFORMATION

SEQUENTIAL READ

SEQUENTIAL CACHE READ RANDOM READ

RANDOM CACHE READ

DATA INTEGRITY TEST

FILE SYSTEM CHECK

SURFACE SCAN

EXIT

DISK TESTS MENU

Disk Information. The Disk Information routine verifies the interface between the CPU Board Assembly and hard disk drive. The processor requests disk information. Data cannot be retrieved successfully if there is a problem. Sequential Read. This routine tries to access every bit of data in the order it is stored directly on the disk. The hard disk drive media may be defective if this routine cannot be completed successfully. Sequential Cache Read. This routine tries to access every bit of data in the order it is stored in the temporary disk memory cache. If this test is not successful, the memory circuits may be faulty. Random Read. This routine tries to access every bit of data in no particular order directly from the disk. This test may detect problems with ability to position the drive heads accurately over the requested data. Random Cache Read. This routine tries to access every bit of data in no particular order from the temporary disk memory cache. If the cache fails this test, memory circuits may contain a fault. Data Integrity Test. This test analyzes the data on the disk drive. The test determines if corrupted data is on the disk. Bad data can cause the program to falter even though the hard disk operates correctly. File System Check. This routine performs a file-by-file check of the data stored on the hard disk. Surface Scan. The magnetic material on the disk can become damaged, causing data to be unreadable. This routine locates unusable areas on the disk and marks them for future reference.

4-8

Page 60

Main Menu (continued) Diagnostics Menu (continued) Switch Tests Screen

SWITCH TESTS SCREEN

Select SWITCH TESTS at the Diagnostics Menu. Switch Tests verify proper operation of the game’s switches, including buttons and joystick switches. Use Switch Tests to locate crossed wires, intermittent conditions and stuck switches.

Activate each switch, and the indicator on the screen changes state. Release the switch and the indicator returns to its previous, normally open or closed condition. You can test any combination of switches together. To exit the test, simultaneously press the middle two control buttons inside the coin door. The Switch Test Screen refers to these buttons as “volume buttons.”

PLAYER SWITCH INPUTS TEST

UP DOWN LEFT RIGHT SHOOT PASS TURBO

P3UPLEFT COIN
P3DOWNRIGHT COIN
P3LEFTP1 START
P3RIGHTSLAMITILT
P3SHOOTTEST
P3PASSP2 START
P3TURBOSERVICE CREDIT

CENTER COIN

P4UPEXTRA COIN
P4DOWNP3 START
P4LEFTP4 START
P4RIGHTVOLUME DOWN
P4SHOOTVOLUME UP

P4 PASS

P4TURBO.BILL VALID.

UP DOWN LEFT RIGHT SHOOT PASS TURBO

P41 49 WAY P2 49 WAY P3 49 WAY P4 49 WAY 24 24 24 24

PRESS BOTH PLAYER 1 AND PLAYER 2 START BUTTONS TO EXIT

SWITCH TESTS SCREEN

Switches appear on the screen as colored boxes. Red boxes indicate an open state. Green indicates closed. Any other color indicates a fault condition. A single indication on the menu screen should exactly duplicate a button or joystick change. You'll notice a unique number for a switch recognized by game electronics.

NOTICE: Some switches may not be used with this game. If you can’t find one of the listed switches, check the wiring diagram.

4-9

Page 61

Main Menu (continued) Diagnostics Menu (continued) DIP Switch Tests Menu

DIP-SWITCH TESTS MENU Select DIP-SWITCH TESTS at the Diagnostics Menu. Two 8-position DIP switch banks reside on the SIO Board. DIP-Switch Tests allow you to check the position of the 16 switches in these banks. You can change the setting of any DIP switch without removing the circuit board cage. The screen displays an illustration of each switch block and the current settings. You can change DIPswitch positions with power on. Set any switch, and then check the screen to verify that the new setting is enabled. Refer to the charts for assistance in choosing switch positions. (* indicates factory defaults.) To exit the DIP-switch Test, press the left control button (inside the coin door). Attract Mode Selection Switch. You can change which Attract Mode sequence the game displays. Select NBA Showtime or NFL Blitz by flipping switch 8 at DIP bank U13. Then power down and up again. Players can still play either game. DIP Switch 1 (U13) Swi | Sw2 | Sw3 | Sw4 | Sw5 | Sw6 | Sw7 | SW8 Coinage Control DIP Switch Off CMOS On* USA1 Gert FrECA1 UK1 Off* | Off* | Off*

USA2 Ger2 FrECA2 UK2OnOffOff
USA3 Ger3 FrECA3 UK3OffOnOff
USA4 Ger4 FrECA4 UK4OnOnOff
USAS Ger5 FrECA5 UK5OffOffOn
USA6 Ger6 FrECA6 UK6OnOffOn
USA7 Ger7 FrECA7 UKECAOffOnOn
USA ECA / Ger ECA / Fr ECA8&OnOnOn
Free Play (All Countries)OnOnOn

Country USA Off* Off*

France On Off

Germany Off On

UK** On On Unused - Off* = On Game NBA Showtime Off* NEL Blitz On **Except Free Play, which is “on” for SW2 through SW6. DIP Switch 2 (U12) Swi | Sw2 | Sw3 | Sw4 | Sw5 | Swe | Sw7 | Sw8 Joystick Type 8-Way Off 49-Way On*

Monitor ResolutionMedium ResOff*

Low Res On

Unused-Off*

= On

Unused7Off*

= On

Unused-Off*

= On Player Panel Type = 2-Player Off 4-Player On*

Power Up Test Active Off

Inactive On*

Operating Mode Game Mode Off* Test Mode On

Page 62

Main Menu (continued) Diagnostics Menu (continued) Speaker Test Menu

SPEAKER TEST MENU Select SPEAKER TEST at the Diagnostics Menu. The Speaker Test provides audio signals to test the loudspeakers. Use tests on the Speaker Test menu to verify operation of audio system components. Highlight an option with any player panel joystick. Select the option with any player panel button.

SPEAKER TEST

LEFT CHANNEL

CENTER CHANNEL

RIGHT CHANNEL

100 HZ TONE

1 KHZ TONE

PLAY TUNE

EXIT

SPEAKER TEST MENU

Channel and Tone Tests. The channel subtests employ voice announcements to verify speaker locations. Use the 100 Hz tone to check the speakers’ bass response. Small speakers with weak magnets or poor baffles may cause poor bass response. Play Tune repeats a series of game sounds. Use PLAY TUNE to check speaker operation and fidelity. If your game has stereo speakers, run PLAY TUNE and test speaker phasing. Muddy, weak or distorted sound during this test may indicate crossed wires or out-of-phase speaker connections. Missing sounds may indicate audio cabling errors.

increase the volume level. Before returning to Game-Over Mode, reset the volume ( ) NOTICE: Check the volume setting before testing. To test the speakers thoroughly, level to its original setting.

Page 63

Main Menu (continued) Audits Menu

AUDITS Select AUDITS at the Main Menu. The Audits menus permit you to review game play statistics. Additional menus give detailed reports for each player position on game starts, ends, cabinet abuse, fault conditions, etc. Highlight an option with any player panel joystick. Select the option with any player panel button. The screen displays a list of the statistics available to you. Select an item to view the detailed report. AUDITS

COIN AUDITS

CREDITS AUDITS

GAME AUDITS

TEAM STATS

GAME FEATURES

EXCEPTION DUMP

CLEAR AUDITS

EXIT

AUDITS MENU

Data in the Audits menus helps you to keep records of the game’s popularity and earning potential. Use the highlight bar to select the desired subject on the Audits Menu. Each entry on the Audits Menu is the subject for an entire screen of bookkeeping information. On these screens, you can track favorite teams, frequently used offensive and defensive plays, etc. Some audits menus also include histograms. Histogram screens allow graphical analysis of statistics. This permits visual comparisons between games. Histograms have no bar graphs until the system acquires enough data to plot. Examine and record all game audit values before performing game service or repairs.

NOTICE: Be careful when clearing audit information. Once you clear data, you cannot restore it.

4-12

Page 64

Main Menu (continued) Audits Menu (continued) Coin Audits Menu

COIN AUDITS

Select COIN AUDITS at the Audits Menu. The Coin Audits menu permits you to assess the currency collection. This report screen presents revenue quantities and other important game statistics. Coin Audits is a read-only screen. To exit, press any player panel button.

COIN AUDITS - PAGE: 1

LEFT SLOT COINS XXXXXXXX

RIGHT SLOT COINS XXXXXXXX

BILLS XXXXXXXX

CENTER SLOT COINS XXXXXXXX

EXTRA SLOT COINS XXXXXXXX

GAME STARTS XXXXXXXX

MID-GAME STARTS XXXXXXXX

CONTINUES XXXXXXXX

CHALLENGER ACCEPTED XXXXXXXX

FREE QUARTERS AWARDED = XXXXXXXX

FREE GAMES AWARDED XXXXXXXK

SERVICE CREDITS XXXXXXXX

UP - NEXT / BUTTON - EXIT

COIN AUDITS MENU

The Coin Audits menu reports total quantities of coins, bills or credits collected by each active device. The menu doesn’t calculate the value of the collected currency.

This screen reports information, but doesn’t permit you to make changes. To reset the coin, bill and credit counters to zero, use the Clear Audits menu.

We recommend that you examine and record audit information before you make changes. Once you’ve cleared the counters, you can’t retrieve the previous data from the system.

COIN AUDITS — PAG

TOTAL PLAYS XXXXXXX

TOTAL PAID CREDITS XXXXXXX

TOTAL XXXXXXX

DOWN - PREV / BUTTON - EXIT

COIN AUDITS MENU, PAGE 2

Page 65

Main Menu (continued) Audits Menu (continued) Credits Audits Screen

CREDITS SCREEN

Select CREDITS AUDITS at the Audits Menu. The Credits Audits Screen permits you to assess the currency collection. This report screen presents revenue quantities and other important game statistics. Credits Audits is a read-only screen. To exit, press any player panel button.

CREDITS AUDITS - PAGE: 1

CREDITS AVAILABLE XXXXXXXX

PRESS ANY BUTTON TO EXIT

CREDITS AUDITS MENU

4-14

Page 66

Main Menu (continued) Audits Menu (continued) Game Audits Screen

GAME AUDITS SCREEN Select GAME AUDITS at the Audits Menu. The Game Audits Screen permits you to review the game play statistics. Game Audits is a read-only screen. To exit, press any player panel button.

GAME AUDITS - PAGE: 1

MACHINE POWER-ON WENT INTO OVERTIME 1 TOTAL UPTIME WENT INTO OVERTIME 2 TOTAL PLAYTIME WENT INTO OT 3 GAMES STARTED 1 PLAYER FINISHES INITIALS ENTERED 2 PLAYER FINISHES <FG> PURCHASED AT START 3 PLAYER FINISHES CREATE PLAYER SESSIONS 4 PLAYER FINISHES 4 PLAYER 2P V CPU FINISHES 2 PLAYER HVS H LSW’S 3 PLAYER CPU WINS (FG) 4 PLAYER AVG H VS H TOTAL SCORE (FG) 2PV CPU AVG H VS CPU TOTAL SCORE (FG) AVG 1 QUARTER GAMES AVG H VS H WIN SCORE (FG) 2 QUARTER GAMES AVG H VS H LOSS SCORE (FG) 3 QUARTER GAMES BIGGEST CPU WIN MARGIN (FG) 4 QUARTER GAMES BIGGEST CPU LOSS MARGIN (FG)

GAME AUDITS SCREEN

The Game Audits Screen reports information, but doesn’t permit you to make changes. Examine and record information at GAME AUDITS before deleting data at the Clear Audits Menu. Once you've cleared the counters, you can’t retrieve the previous data from the system.

GAME AUDITS SCREEN TERMS SCREEN SCREEN

TERM DEFINITION TERM DEFINITION

AVGAverageLswYourgamecomputer's _ internal

record-keeping counters CPU Central Processing Unit: The game

computerMachineNumber of power cycles (game turn-

Power-On ons) <FG>, (FG) | Full Game oT Overtime HVS CPU | Human versus CPU: Competition that

pits players against the game computerPVPlayer versus...

HVSH Human versus human: Competition | Total Uptime | Overall on-time for the game between human players computer

2PV Two players versus...

Page 67

Main Menu (continued) Audits Menu (continued) Team Stats Screen

TEAM STATS SCREEN

Select TEAM STATS at the Audits Menu. The Team Stats Screen details the number of games played by each team in the league. Team Stats is a read-only screen. To exit, press any player panel button.

TEAM STATS - PAGE: 1

ATLANTA HAWKS0%NEW JERSEY NETS
BOSTON CELTICS0%NEW YORK NICKS
CHARLOTTE HORNETS0%ORLANDO MAGIC
CHICAGO BULLS0%PHILADELPHIA 76ERS
CLEVELAND CAVALIERS0%PHOENIX SUNS
DALLAS MAVERICKS.0%PORTLAND TRAILBLAZERS
DENVER NUGGETS.0%SACRAMENTO KINGS
DETROIT PISTONS0%SAN ANTONIO SPURS.
GOLDEN STATE WARRIORS.0%SEATTLE SUPERSONICS
HOUSTON ROCKETS0%TORONTO RAPTORS.

INDIANAPOLIS PACERS 0% UTAH JAZZ

LOS ANGELES CLIPPERS0%VANCOUVER GRIZZLIES
LOS ANGELES LAKERS0%WASHINGTON WIZARDS

MIAMI HEAT 0%

MILWAUKEE BUCKS 0%

MINNESOTA TIMBERWOLVES 0%

PRESS ANY BUTTON TO EXIT

TEAM STATS SCREEN

Page 68

Main Menu (continued) Audits Menu (continued) Game Features Screen

GAME FEATURES SCREEN

Select GAME FEATURES at the Audits Menu. Game Features tracks play statistics that relate characters in the game and game play. Game Features is a read-only screen. To exit, press any player panel button.

GAME FEATURES - PAGE: 1

UMBER OF PLAYER RECORDS.

NUMBER OF LRU RECORDS

RECORDS FROM CREATE PLAYER

NUMBER OF PLAYER FIRE

AVG PTS PLAYER FIRE

NUMBER OF TEAM FIRE

AVG PTS TEAM FIRE

NUMBER OF ALLEY OOPS

NUMBER OF DOUBLE DUNKS

CREATP MASCOT HEADS

CREATP NBA HEADS.

CREATP FEMALE HEADS

CREATP UM HEADS

CREATP MID HEADS

CREATP OTHER HEADS

CREATP DEFAULT UNIFORM CREATP CUSTOM UNIFORM

CREATP TEAM UNIFORM

CREATP NICKNAME

CREATP AVG HEIGHT PTS

CREATP AVG WEIGHT PTS

CREATP AVG PWR PTS

CREATP AVG SPEED PTS

CREATP AVG TWOPTS PTS

CREATP AVG STEAL PTS

CREATP AVG BLOCK PTS

CREATP AVG DUNK PTS

PRIV1

PRIV2

PRIV3

EXT / BUTTON - EXIT

GAME FEATURES SCREEN, PAGE 1

Number Of Player Records. Number of player initial sets entered in CMOS RAM. Number Of LRU Records. Number of record slots (space for player data) left in CMOS RAM. Records From Create Player. Number of player records produced in Create Player Mode. Number Of Player Fire. Number of times a player has started on fire. Avg Pts Player Fire. Average number of points that player scored while player was on fire. Number Of Team Fire. Number of times that the team has started on fire.

Avg Pts Team Fire. Average number of points that the team scored while it was on fire. Number Of Alley Oops. Total number of alley oops performed. Number Of Double Dunks. Total number of double dunks performed. Creatp Mascot Heads. Number of player-created characters with mascot heads. Creatp NBA Heads. Number of player-created characters with NBA-personality heads. Creatp Female Heads. Number of player-created characters with female heads. Creatp UM Heads. Number of player-created characters with Universal Studios monster heads.

4-17

Page 69

Creatp Mid Heads. Number of player-created characters with Midway Games heads. Creatp Other Heads. Number of player-created characters with custom heads. Creatp Default Uniform. Number of player-created characters with the selected team’s uniforms. Creatp Custom Uniform. Number of player-created characters with custom uniforms. Creatp Team Uniform. Number of player-created characters with specific team uniforms. Creatp Nickname. Number of player-created characters with nicknames. Creatp Avg Height Pts. Average height attribute setting. Creatp Avg Weight Pts. Average weight attribute setting. Creatp Avg Pwr Pts. Average power attribute setting. Creatp Avg Speed Pts. Average speed attribute setting. Creatp Avg TwoPts Pts. Average two-point shot attribute setting. Creatp Avg Steal Pts. Average stealing attribute setting. Creatp Avg Block Pts. Average blocking attribute setting. Creatp Avg Dunk Pts. Average dunking attribute setting. Priv1. Number of times player-created characters include privilege 1 (a player selection). Priv2. Number of times player-created characters include privilege 2 (a player selection). Priv3. Number of times player-created characters include privilege 3 (a player selection). Priv4. Number of times player-created characters include privilege 4 (a player selection). Priv5. Number of times player-created characters include privilege 5 (a player selection). Priv6. Number of times player-created characters include privilege 6 (a player selection). Priv7. Number of times player-created characters include privilege 7 (a player selection). Priv8. Number of times player-created characters include privilege 8 (a player selection). Game With Creatp. Number of games played with player-created characters. Win V CPU With Creatp. Number of player-won games with player-created characters. Win V Human With Creatp. Number of computer-won games with player-created characters. Tournament Games. Number of games played in Tournament-Scoring Mode. Timer Level. Speed at which game machine produces time-released and created characters. TLF’s. A counter employed by designers (has no purpose in the field). SBLF’s. A counter employed by designers (has no purpose in the field).

Page 70

GAME FEATURES - PAGE: 2

PRIV4

PRIVS

PRIV6

PRIV7

PRIV8

GAME WITH CREATP

WIN V CPU WITH CREATP

WIN V HUMAN WITH CREATP

TOURNAMENT GAMES

TIMER LEVEL

TLF’S

SBLF’S

GAME FEATURES SCREEN, PAGE 2

Page 71

Main Menu (continued) Audits Menu (continued) Exception Dump Screen

EXCEPTION DUMP SCREEN

Select EXCEPTION DUMP at the Audits Menu. Game programmers use the Exception Dump Screen to view register contents during program development. This menu has no field purpose. Exception Dump is a read-only screen. To exit, press any player panel button.

Main Menu (continued) Audits Menu (continued) Clear Audits Menu

CLEAR AUDITS MENU

Select CLEAR AUDITS at the Audits Menu. The Clear Audits menu allows you to clear individual memory counters or to reset them all at once.

Highlight an option with any player panel joystick. Select the option with any player panel button.

CLEAR AUDITS

CLEAR COIN AUDITS

CLEAR CREDITS AUDITS

CLEAR GAME AUDITS

CLEAR TEAM STATS

CLEAR GAME FEATURES

CLEAR GAME RESETS

CLEAR EXCEPTION DUMP

CLEAR ALL

EXIT

CLEAR AUDITS MENU

You can reset any audit screen from the Clear Audits Menu. Choose an item and zero its counter. CLEAR ALL simultaneously changes all audit categories to factory default values. After you've selected an item, the system gives you the opportunity to escape this change. For example:

ARE YOU SURE YOU WANT TO CLEAR COIN AUDITS?

LAST CHANCE MENU

After you've selected and verified a clear function, the values reset. The system can’t restore the previous values. Examine and record utility values before you make changes.

4-20

Page 72

Main Menu (continued) Adjustments Menu

ADJUSTMENTS Select ADJUSTMENTS at the Main Menu. The Adjustments menus permit you to change game characteristics. Use these screens to optimize game performance and earnings. Highlight an option with any player panel joystick. Select the option with any player panel button.

ADJUSTMENTS

PRICING

FREE PLAY

ATTRACT SOUND

ADDITIONAL ADJUSTMENTS

FULL FACTORY RESTORE

EXIT

ADJUSTMENTS MENU

Main Menu (continued) Adjustments Menu (continued) Pricing Menu

PRICING MENU Select PRICING at the Adjustments Menu. The Pricing menus allow you to view current settings or change the cost of games. Custom pricing allows you to select the number of coins or credits required for each game. The game restores factory default values if you exchange the CPU Board or if the backup battery fails. Highlight an option with any player panel joystick. Select the option with any player panel button. You can set options to factory defaults or change an option after viewing it. We recommend examining and recording pricing options before making changes. You can save several custom prices and then choose between them as needed. On-screen instructions guide you through the process of creating custom price settings.

PRICING

SHOW CURRENT NORTH AMERICA SOUTH AMERICA EUROPE (A-G) EUROPE (H-Z) ASIA AUSTRALIA ISTOM PRICING EXIT

PRICING MENU

An additional box appears on screen to explain the available functions as you select each item.

4-21

Page 73

STANDARD PRICING TABLE

NAMESTARTCONTINUE | CREDITS/COINCOINT | COIN2 | COIN3 | COINS | BILL
ANTILLES221/25¢, 4G.25¢1G
‘AUSTRALIA 122113X20¢, 2/$1.0020¢$1.00
AUSTRALIA 2221/5X20¢, 1/$1.0020¢$1.00
‘AUSTRIA 122Sch, 2/108ch5 Sch| 10Sch
AUSTRIA 2224/2X5Sch, 3/2X10Sch5Sch | 10Sch
BELGIUM 1221/20BF20BF20BF
BELGIUM 2223/20BF20BF20BF
BELGIUM 3222/20BF20BF20BF
BELGIUM ECA221/20BF50BF20BFSBF
CANADA 122172 x 25¢, 378125¢25¢
CANADA 2221/2x 25¢,3/$125¢$1.00
CANADA 3223/ $1.00, 6 / $2.00$1.00 | $2.00
CANADA ECA221/2x25¢,3/$125¢$1.00 | $2.00
DENMARK22‘3/SDKr, 7/10DKr‘SDKrODKr
FINLAND2241 Fmk4Fmk__|5¢mk
FRANCE 1222/5Fr, S10FrSFr10Fr
FRANCE 2212i5Fr, 4/10FrSFr10Fr
FRANCE 3214/5Fr, 3/10FrSFr10Fr
FRANCE 4214/5Fr, 20FrSFr10Fr
FRANCE 5212I5Fr, S/10Fr, 11/2 X 10FrSFr10Fr
FRANCE 6212/5Fr, 4/10Fr, 9/2 X 10FrSFr10Fr
FRANCE 7214/5Fr, 3/10Fr, 7/2 X 10FrSFr10Fr
FRANCE 8214/5Fr, 2/10Fr, 5/2 X 10FrSFr10Fr
FRANCE 921413 X 1Fr, 2/5Fr1FrSFr
FRANCE 10214/2 X 1Fr, 3/5Fr1FrSFr
FRANCE 1121413 X 1Fr, 2/5Fr, 5/2 X SFr4FrSFr
FRANCE 12211/2 X 1Fr, 3/5Fr, 7/2 X SFr4FrSFr
FRANCE ECA 111215Fr, S/10Fr1FrSFr10Fr20Fr
FRANCE ECA 2112I5Fr, 4/10Fr4FrSFr10Fr20Fr
FRANCE ECA 3114/5Fr, 3/10Fr4FrSFr10Fr20Fr
FRANCE ECA 4114/5Fr, 20Fr4FrSFr10Fr20Fr
FRANCE ECA 5112i5Fr, S/10Fr, 11/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 6112I5Fr, 4/10F r, 9/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 7114/5Fr, 3/10Fr, 7/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 8114/5Fr, 2/10Fr, 5/2 X 10Fr1FrSFr10Fr20Fr
FRANCE ECA 911413 X 1Fr, 2/5Fr1FrSFr10Fr20Fr
FRANCE ECA 10 | 411/2 X 1Fr, 3/5Fr1FrSFr10Fr20Fr
FRANCE ECA 11| 41413 X 1Fr, 2/5Fr, 5/10Fr1FrSFr10Fr20Fr
FRANCE ECA 12| 41412 X 1Fr, 3/5Fr, 7/10Fr1FrSFr10Fr20Fr
FRANCE ECA13__|414M 0F r, 2/20Fr, 4/30Fr4FrSFr10Fr20Fr
FREE PLAY===NoneNoneNoneNoneNone
GERMANY 122771M, 6/5DM7DMSDM
GERMANY 2214/4DM, 7/5DM1DM5DM
GERMANY 32141M, 8/5DM1DM5DM
GERMANY 4214/4DM, 5/5DM1DM5DM
GERMANY 5214/1DM, 6/5DM1DM5DM
GERMANY ECA1 | 2241M, 2/2DM, 6/5DM1DM20M5DM
GERMANY ECA2 | 2141M, 2/2DM, 6/5DM1DM20M5DM
GERMANY ECA3_|114/1DM, 2/2DM, 6/5DM1DM20M5DM
HUNGARY,22472X10F t, 3/2X20Ft40Ft20Ft
ITALY,224/500L1t‘S00LIt__|SO0LIt
JAPAN 1227/100Yen100100
JAPAN 2222/100Yen100100
NETHERLANDS224MHFI, 3/2.5HFI4HFI2.5HFI
NEW ZEALAND 1 | 11111$1$2
NEW ZEALAND 2 | 112181$1$2
NORWAY.22BISNKr, 6/10NKrSNKrTONKr
‘SPAIN 1221/100Pta, 6/500Pta100Pta | 500Pta
SPAIN 2221/100Pta, 5/500Pta100Pta_|500Pta
‘SWEDEN,2243X18Kr, 2/5SKrTSKr5SKr
SWITZERLAND 1 | 224/1SFr, 6/5SFr1SFrSSFr
SWITZERLAND 2 | 224/4SFr, 7/5SFr1SFr5SFr
SWITZERLAND 3_|224/4 SFr, 8/5SFr1SFr5SFr

(Table continues on next page)

4-22

Page 74

STANDARD PRICING TABLE, continued

NAMESTARTCONTINUE | CREDITS/COINCOIN1 | COIN2 | COINS | COIN4 | BILL
UKECA4111150p, 3/£1.00£1.00 | 50p20p10p£2.00
UK ECA2111150p, 2/81.00£1.00 | 50p20p10p£2.00
UKECA3111/30p, 2/50p, 5/£1.00£1.00 | 50p20p10p£2.00
UK4111150p, 3/£1.00£1.00 | 50p
UK:111150p, 2/81.00£1.00 | 50p
UK ECA6111130p, 2/50p, 4/£1.00£1.00 | 50p20p0p£2.00
UKECAT11371.00£1.00 | 50p20p10p£2.00
UKECA8111150p, 2/81.00, 4/£2.00£1.00 | 50p20p10p£2.00
USAT221125¢25¢25¢$1.00
USA2211125¢25¢25¢$1.00
USA3111125¢25¢25¢$1.00
usa4111150¢, 3/$1.0025¢25¢$1.00
USAS211150¢, 4/$1.0025¢25¢$1.00
USA6111150¢25¢25¢$1.00
UsA7111150¢, 3/$1.0025¢25¢$1.00
usAs221150¢, 4/$1.0025¢25¢$1.00
USsAg321125¢, 4/$1.0025¢25¢$1.00
USA10331125¢, 4/$1.0025¢25¢$1.00
UsA11421125¢, 4/$1.0025¢25¢$1.00
UsA12431125¢, 4/$1.0025¢25¢$1.00
USA13441125¢, 4/$1.0025¢25¢$1.00
USAECA331125¢, 4/$1.00$1.00 | 25¢10¢05¢$1.00

4-23

Page 75

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Current Pricing Screen

CURRENT PRICING SCREEN

Select SHOW CURRENT at the Pricing Menu. The Current Pricing Screen is a read-only screen. Use it to check pricing parameters for the pricing table your game is using. To select a new pricing table, return to the Pricing Menu. To create your own pricing table, select Custom Pricing on the Pricing Menu. Press any START button to exit from the Current Pricing Screen.

CURRENT PRICING

LEFT SLOT UNITS

RIGHT SLOT UNITS

CENTER SLOT UNITS

EXTRA SLOT UNITS

BILL VALIDATOR UNITS

UNITS PER CREDIT

UNITS PER BONUS

MINIMUM UNITS

CREDITS TO START

CREDITS TO CONTINUE

MAX CREDITS

COINS PER BILL

CURRENT PRICING SCREEN

The following table clarifies Pricing Menu terms:

SCREEN TERM DISCUSSION

Slot Units; Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism

programming, knows that your coin is worth one unit. Units per Credit How many units equal one credit. (Units buy credit, the price of one game.) Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits.

Credits to Start Number of games a player must purchase to begin play.

Credits to Continue Number of games a player must purchase to resume play.

Max Credits Limits the number of credits that the game will accept.

Coins per Bill How many coins one bill is worth.

4-24

Page 76

Main Menu (continued) Adjustments Menu (continued) Pricing Menu (continued) Custom Pricing Menu

CUSTOM PRICING MENU

Select CUSTOM PRICING at the Pricing Menu. The Custom Pricing Menu permits you to program and use your own pricing table. The menu heading CREATING XXXX allows you to input a descriptive name for your new pricing table. You can save several pricing schemes and chose between them as desired. Highlight an option with any player panel joystick. Change the option with any player panel button. Press any START button to save your pricing table and exit from the menu.

CREATING XXXX

LEFT UNITS RIGHT UNITS

CENTER UNITS EXTRA UNITS

DBV UNITS UNITS PER CREDIT

UNITS / BONUS MINIMUM UNITS

CREDITS TO START CREDITS TO CONT.

MAX CREDITS COINS / BILL

SHOW FRACTIONS LEFT COUNT

RIGHT COUNT CENTER COUNT

EXTRA COUNT DBV COUNT

USE STICK TO SELECT AN ITEM TO MODIFY

PRESS ANY BUTTON TO MODIFY THE ITEM

PRESS ANY START BUTTON TO SAVE AND EXIT

CUSTOM PRICING MENU

The Custom Pricing Menu employs the same terms that appear on the Current Pricing Table. See the table below for definitions of these terms.

PRICING MENU TERMS

SCREEN TERM DISCUSSION

Slot Units;

Bill Validator (DBV) Units Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit.

Units per Credit How many units equal one credit. (Units buy credit, the price of one game.)

Units per Bonus Units awarded when a player earns a bonus. Minimum Units Until this many units accumulate, the system awards no credits.

Credits to Start Number of games a player must purchase to begin play. Credits to Continue Number of games a player must purchase to resume play. Max Credits Limits the number of credits that the game will accept.

Coins per Bill How many coins one bill is worth.

4-25

Page 77

BASIC CUSTOM PRICING. Custom pricing creates an imaginary currency exchange. In this currency exchange, the coins of the realm are “units.” Think of units as a type of cyber-currency, useful only within the game software. By inserting coins, you purchase units. Since units are only negotiable within game software, the system stores your units for you. When the system receives enough units, it buys a game for you. The price of a game is one “credit.” You can think of credits as a second form of cyber-currency. Even though you’ve now bought one game, you may not be able to begin playing. In many pricing schemes, you must buy two or more credits to begin play. The idea here is something like a minimum order of goods at a store. That is, the operator can “shrink-wrap” two or more games in a package. You can’t play unless you buy the entire package. 1 / 25¢ COIN; 1 CREDIT TO START. In a simple, quarter pricing scheme, the player inserts one coin to buy one unit. The system exchanges that unit for one credit. If CREDITS TO START contains the value one, then play commences. A dollar bill buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14114

e1 / 3 X 25¢; 2 CREDITS TO START. Again, assuming quarter slots, here’s one way to implement 75¢ pricing... In this scheme, each coin that the player inserts buys one unit. The system exchanges three units for one credit. CREDITS TO START contains the value two. To play, the player must pay for two credits. In this scheme, a dollar buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
14324

e2 / 1 COIN; 6 CREDITS TO START. Now let's consider a more unusual pricing scheme. Here, the player can buy two units with one coin. The system exchanges each of these units for one credit. Notice that CREDITS TO START contains the value six. To play, the player must insert two more coins to pay for six credits. Also notice that if the player pays with a bill, the system throws in an extra unit.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill
29164

4-26

Page 78

Main Menu (continued) Adjustments Menu (continued) Free Play Feature

FREE PLAY FEATURE Select FREE PLAY at the Adjustments Menu. Free Play is a useful feature for promotions and long-term testing under play conditions. Enable Free Play to allow players to play the game without inserting currency. Disable Free Play to sell games. Highlight an option with any player panel joystick. Select the option with any player panel button.

Main Menu (continued) Adjustments Menu (continued) Attract Sound Menu

ATTRACT SOUND MENU Select ATTRACT SOUND at the Adjustments Menu. The Attract Mode operates between games. It attempts to lure prospective players into trying your game. Attract Mode sound may not be appropriate for some locations. The Attract Sound Menu allows you to enable or disable the Attract Mode sound feature. You can turn Attract Mode sound on or off without changing the game volume level. Highlight an option with any player panel joystick. Select the option with any player panel button.

ENABLE ATTRACT MODE SOUNDS?

ATTRACT SOUND MENU

4-27

Page 79

Main Menu (continued) Adjustments Menu (continued) Additional Adjustments Menu

ADDITIONAL ADJUSTMENTS MENU Select ADDITIONAL ADJUSTMENTS at the Adjustments Menu. Additional Adjustments menu items allow you to set the game to match player requirements. These adjustments affect speed, challenge, rewards, etc. that determine player enjoyment. Highlight an option with any player panel joystick. Select the option with any player panel button.

ADDITIONAL ADJUSTMENTS

GAME DIFFICULTY DISCOUNT PRICE / CREDITS CLOCK SPEED FREE GAME - FULL 4 PLR. FREE GAME - FULL 10ON1 FREE GAME - FULL V. CPU FREE QUARTER - FULL 4 PLR. FREE QUARTER - FULL 1 ON 1 FREE QUARTER - FULL V. CPU CLEAR PLAYER RECORDS CLEAR WORLD RECORDS PLAYER HEAD SIZE TOURNAMENT MODE COMPUTER ASSISTANCE ATTRACT MOVIE SOUND EXIT

ADDITIONAL ADJUSTMENTS MENU

Game Difficulty allows you to alter the challenge that a game poses to players. Choose the level that most closely matches the players’ skills. Discount Price / Credits adjusts the quantity of buy-in points to encourage multiple game purchases. Clock Speed alters how much game time that a player can purchase for one credit. Choose one of these settings: Extra slow, slow, medium, fast or extra fast. Free Game, when enabled, allows the program to award a free game. The free game may be a fourplayer or a one-on-one game. The free game may also involve competition against the game computer. Free Quarter. The program divides games into quarters, as in NBA rules. The Free Quarter feature, when enabled, allows the program to award a free game quarter. The free quarter may be a four-player or a one-on-one quarter. The free quarter may also involve competition against the game computer. Clear Player Records allows you to zero out game play data. Examine and record this information before you clear it. Once you've cleared player records, you can’t retrieve the previous data. Clear World Records allows you to zero out world record data. Examine and record this information before you clear it. Once you've cleared player records, you can’t retrieve the previous data. Player Head Size allows you to alter the head size of on-screen characters. This feature determines whether the characters appear more lifelike, or more like caricatures. Choose “normal” or “big.” Tournament Mode, when enabled, adapts your game’s scoring for tournament-style play. Computer Assistance, when enabled, permits the game computer to aid players in play action. Attract Movie Sound, when enabled, allows Attract Mode movie sound with Attract Mode sound off. The Attract Mode movie is only one component of the Attract Mode graphics.

4-28

Page 80

Main Menu (continued) Volume Level Menu

VOLUME LEVEL MENU Select VOLUME LEVEL at the Main Menu. When you display the Volume Level Menu, music plays continuously. Raise or lower the game’s sound level with any player panel joystick. (You can also use the volume up/down buttons on the diagnostic switch bracket.) Save your change and return to the Main Menu by pressing any player panel button.

SET VOLUME LEVI

MAX

UP / DOWN TO ADJUST VOLUME

PRESS ANY BUTTON TO SET VOLUME AND EXIT

VOLUME LEVEL MENU

Loud games attract more player interest than games with low-level sound. The Attract Mode sound level is always lower than the game play sound level.

NOTICE: These adjustments affect the volume of tests as well as of game play. If you set volume levels to minimum (zero), the speakers are silent during audio tests. We recommend setting volume levels to a moderately high value whenever you perform sound tests. After you complete tests, you may return sound levels to previous settings.

4-29

Page 81

Main Menu (continued) Adjustments Menu (continued) Full Factory Restore Feature

FULL FACTORY RESTORE FEATURE Select FULL FACTORY RESTORE at the Adjustments Menu. The Full Factory Restore menu allows you to clear all memory counters at once. Highlight an option with any player panel joystick. Select the option with any player panel button.

RESTORE ADJUSTMENTS & AUDITS?

FULL FACTORY RESTORE MENU

NOTICE: Examine and record audit information before you make changes. Once you've cleared the counters, you can’t retrieve previous data from the system.

Examine and record utility values before you make changes. If you choose YES, the system restores all adjustments and audits to factory default values. This change isn’t reversible. The system can’t restore the previous values. With the settings restored, the system displays the Reset Complete Screen.

AUDITS & ADJUSTMENTS RESTORED

PRESS ANY BUTTON TO EXIT

RESET COMPLETED SCREEN

4-30

Page 82

Main Menu (continued) Attract Mode Volume Level Menu

ATTRACT MODE VOLUME LEVEL MENU Select ATTRACT VOLUME LEVEL at the Main Menu. When you display the Attract Mode Volume Level Menu, music plays continuously. Raise or lower the game’s Attract Mode sound level with any player panel joystick. (You can also use the volume up/down buttons on the diagnostic switch bracket.) Save your change and return to the Main Menu by pressing any player panel button. Your setting won't affect the game play sound level.

SET ATTRACT VOLUME LEVEL

MAX

UP / DOWN TO ADJUST VOLUME

PRESS ANY BUTTON TO SET VOLUME AND EXIT

ATTRACT MODE VOLUME LEVEL MENU

Increase the Attract Mode sound level to generate player interest. The game play sound-level setting determines the maximum level for Attract Mode sound. Regardless of your setting, the Attract Mode level remains lower than the game play level.

4-31

Page 83

Main Menu (continued) Utilities Menu

UTILITIES Select UTILITIES at the Main Menu. Utilities Menu items allow you to clear bookkeeping totals. From the Utilities Menu, you can also restore game adjustments to factory settings. Highlight an option with any player panel joystick. Select the option with any player panel button.

UTILITIES

DUMP AUDITS CLEAR CREDITS CLEAR AUDITS. RESET HIGH SCORES DEFAULT ADJUSTMENTS FULL FACTORY RESTORE DISCOUNT PRICE / CREDITS EXIT

UTILITIES SCREEN

Dump Audits allows you to send data to the game computer’s serial port. You can connect a serial printer to make a paper record of your audit data. Clear Credits opens a menu that allows you to zero the game’s credit data. Examine and record audit information before you make changes. Clear Audits opens a menu that allows you to zero the game’s audit data. Reset High Scores permits you to delete player names and scores that appear in the Attract Mode. This feature may be useful if players insert inappropriate language into the high score table. Default Adjustments opens a menu that allows you to reset game adjustments to factory settings. Full Factory Restore allows you to reset game adjustments and audits to factory settings. Discount Price / Credits permits you to enter special game pricing or award extra credits. You can use this feature for advertising or promotional purposes.

NOTICE: Be careful when clearing audit information. Once you clear data, you can’t restore it.

4-32

Page 84

SPORTSTATION

CHAPTER

FIVE

PARTS

WARNING: Use of non-Midway parts or circuit modifications may cause serious injury or equipment damage! use only Midway authorized parts. For safety and reliability, don't substitute parts or modify MIDWAY products. Substitute parts or modifications may void the game’s EMC directive or FCC type acceptance.

5-1

Page 85

CABINET FRONT VIEW

20-9347 TOSGLE LACHES)

21512 TERWINAL SLOCK COVE? — ASSEMBLY

M3710 Ot, FLEXWLE ET i t i A21196__ Koo TERMINAL 8LOCE Ty

20-10400.1__ E Li

TOR ADJUSTMENT ToL

20-9275-4 SFT) CHAIN

5555-15142-00__ FEI

4108-01193-108 HEET METEL “CPE: TAMPER PESITANT

01-14524-1 PEAKE CPILL

4020-01070-32 MECHINE SORE In HH

04-10648-1, Dp PANEL

5-2 03-9630-1_ FecTENE! 23487 FRONT Hi 25SEMPL

_5675-15773-00 | HED. FES. MONITOL | __ 08-8016 PEZEL—CAPDPOAPL

_01-14522 PROP ROL

ELECTRONICS 455EMBL EE DETAIL bkAvIN

20-10187 CAM LOCK

A21469-1 AE PANEL ven AN sD

A-23489 J cone Hous | NTPOL PANEL | | oom DOOR (SEE i PT ePrucstion: SHEET i | I ‘A-23488 NThOL Pot

___ 08-7377 f LEVELER ADJ STE __ 03-9631 AP FASTENER SHEL

4020-01005-24 SHECHINE SCRE 1 FH

Page 86

CABINET REAR VIEW

4108-01193-10B 7 TAMPER PESETANT SORE : # 1 5675-15773-00 MEDIUM, PES OLUTION \ IDES MOMITOL 01-1396 4 TOP VENT

f | __ 03-9599 4 PLeSTIO Lh

be MONITOR CIRCUIT ut X __20-10187 boaRD SET IN , AM LOCK

A o _— A-21874 ACCESS L

| 20-10400.1 y POWER SUPPL

(P__ LINE CORD. (SEE W—SPPLICATION CHART | __ 20-9420 FAN GUARL

4108-01193-10B TAMPER PESISTANT SCPE

  • TI

A-23488 NTRCL POR — | 5 SEMEL — |

A-23485 MAIN CSBINET— 2SSEHBL

20-10354 , WEL CASTEL __08-7377 LEVEL Abo USTED

Page 87

FRONT HOUSING ASSEMBLY A-23487

24-8809 FLUORESCENT To FE—

22508 FLOORESCENT Lali SEN LE ELECTRON P2LL2T

04.10639.1-1 a % FORMED Hoo sIN :

03.9633 _ : AL NEP OUEE PETSINE! ll

4108-01193-108 | fl TAMPER PESISTENT "HEEL 4 |

4700-00129-00B FLAT VS 0HER = i

_ 31-3493 PEZEL DECAL __ 03-9635 i Eb 4700-00032-00B _ FLAT 2 0HEL x can 04-10640_ LIGHT COVE! ad

< 4020-01100-08 | &%, TAMPER RESISTANT ad I- POTTON HEED SCPE _ 03-9632 NFO EE PANEL

31-9515-3 SPeOKUIT MAR OUEE

_on-aasat FT SHIELD RETAINE!

ral 4108-01219-11 TP IN-H

~ __ 08-8015 nN VT GL

__04-10641.2 LOWER PRECKET

__04-10798 SAFETY CHAIN BEKT

a __ 20-9275-3 SFET) OHEIN

4020-01070-08 SHETEL SOFE i= HH

4701-00005-00 LOCK SHER ¢/4 SPLIT

Page 88

MOUNTING HARDWARE KIT A-21926

5-5

Page 89

CONTROL PANEL & HOUSING ASSEMBLY A-23489

BOTTOM EE PETAIL DRA H TI EE DETAIL bh

4010-01100-08 TAMPER-RESISTANT RE

4108-01193-10B TAMPER-PESISTANT REW—

TION 03-9634 NOTH ERLE

TON 31-3494 INT PANEL

4020-01070-08

  • METAL 4700-00129-00B FLAT Me HEF __

SHEL

03-9768.1

31-3495.1 NTPOL PSNEL DECAL

04-11266.2 LoPSNEL PLATE aa)

NT

FE HH

4108-01193-10B —THPEL FE RESISTANT VL-HOH 14-1274 PACER

T, PL-HUH 4106-01115-12 HIGH Fe H 04-10646.1-1 E F

PESKEL 5555-15141-00

s s ASSEMBL ADAPTER

03-8338-1 PACEL

04-11324. 4108-01219-11 UGHT £5 0EMEL Trl PL-HWH 24-8873 ENT | ul = INCANDE

5-6

Page 90

COIN DOOR ASSEMBLY

KEY= aM Look WW ENTPY ‘ VTE 27-3729

MOT WSSHER—;27-3725Buon PeeEt

i ENTRY ( REJE-T—

AM LOCK ARM ga/Seq;

Ly | i

eee mulu1 | VEIECT BEZEL

? I | — 27-3731

|Who\VEIE T FLAI

[ |

MECH HOLDER —iA|i
\fei
fii|
ryt i"|= PPER PLATE

i i | IM MECH i | ) ] dere Hi ral | | 1 of ;

VyI— SPACER
IN STH.|
in||
eeI|

inte Lover pLete

‘_03-8863— HEX NUT

25H Tu

I | NOTE SEE COI Pook 5580-13476-00 SPPUCATION CHEPT COIN HIETEI FOR 20SEMPLY NUMPEF

5-7

Page 91

49-WAY JOYSTICK ASSEMBLY A-21939-1 AND BUTTON ASSEMBLY 20-10209-X

5-8

Page 92

ELECTRONICS ASSEMBLY A-23486

5-9

Page 93

POWER SUPPLY 20-10400.1

5-10

Page 94

SOUND I/O CARD A-23431-2

Field Replaceable Parts

Description Location Part Number

Capacitor, 2200 uF, 16VC3105040-15904-00
Capacitor, 2200 uF, 25VC2545040-14630-00
Crystal, 4 MHz, Type HC49UY25520-14602-00
Crystal, 16 MHz, Type HC49UY35520-14595-00
Crystal, 20 MHz, 3-Lead TypeY15520-15159-00
Heatsink, TO-220, Type 5298bU19, U205705-12638-00
IC, TDA7240V, 20W AmplifierU19, U205370-14146-00
Oscillator, 33 MHZ, TTL, Tri-StateU35521-13806-06

ROM, Sound Boot U44 A-5343-45994-2

Shunt, 0.025” Square PinsAny Jumper5882-13046-00
Page 95

CPU BOARD ASSEMBLY A-23429

Field Replaceable Parts

Description Location Part Number

Capacitor, 2200 uF, 16V, Radial C24, C115, C209, 5040-15904-00 C229, C294 Heatsink, TO-220, Small U5 5705-14562-00 Heatsink, TO-220, Type 5298b U15 5705-12638-00 Regulator, CS5203a U5 5250-16015-00 ROM, Boot U27 A-5343-45994-1

5-12

Page 96

BANSHEE VIDEO CARD 20-10516

No Field-Replaceable Parts

5-13

Page 97

AUXILIARY ADAPTER CARD ASSEMBLY 04-12652

No Field-Replaceable Parts

I-40 BOARD ASSEMBLY 04-11089

TI

No Field-Replaceable Parts

5-14

Page 98

5-15 24-8809 FLUORESCENT LaMP 04-11241.1 ao SEMBL 20-10444 _ LéMP HOLE! 20-10481.1 “ELECTRONIC FALLAST FIXTURE PACE FLUORESCENT LAMP ASSEMBLY A-22506

Page 99

OTHER PARTS

Buttons Button, Long Shaft, Blue. Button, Long Shaft, Orang Button, Long Shaft, Red. Button, Long Shaft, White . 20-10209-3

  • 20-10209-7 . 20-10209-1
  • 20-10209-2

Cables Cable, AC, 39” Cabinet. Cable, Control Panel... Cable, Hard Drive Power Cable, Main Harness (JAMMA) Cable, Ribbon, 40-Pin. Cable, Ribbon, 20-Pin. Harness, Fluorescent Lamp . Harness, Strip Light and Speaker.

Documents Card, Game Information . Manual, SportStation, 39’ --16-10650 16-40098-101

Fuses Fuse, 3AG, 1ASB, 250V. Fuse, 3ASB, 250V

Kit, Spare Parts Kit, Spare Parts Bulb, Incandescent, 6.3V, #555. Fuse, 3AG, 1A, 250V........ Wrench, T-20, Long Arm Tamper-Resistant (Torx®) Wrench, T-25, Long Arm Tamper-Resistant (Torx®) Wrench, T-27, Long Arm Tamper-Resistant (Torx®)

Page 100

RIGHT-ANGLE LINE CORD APPLICATION TABLE

5850-14699-00 5850- 14699-01 5850-14699-02 5850-14699-03 5850-14699-04 5850-14699-05 5850-14699-06

New Zealand Germany Spain Denmark Finland Holland Norway Switzerland Hungary Canada Austria France Australia Belgium

TYPICAL I.E.C. LINE CORD WITH INLINE FEMALE PLUG

Page 101

COIN DOOR APPLICATION TABLE

09-96009-15 09-96009-17 09-96009-22 09-96009-23 09-96009-25 09-96009-33 09-96011.1-00 (Electronic) Country Australia Austria Belgium Canada Denmark Finland France Germany Holland Hungary Italy Japan New Zealand Norway Spain Switzerland UK USA

Page 102

SPORTSTATION

CHAPTER

SIX

WIRING

WARNING: Failure to reconnect ground wires or replace metal shields and covers with mounting hardware installed and properly tightened may result in radio frequency interference.

6-1

Page 103

Function JAMMA Chart

Wire Color Function Wire Color Ground Black Ground Black Ground Black Ground Black +5VDC Red +5VDC Red +5VDC Red +5VDC Red -5VDC Yellow -5VDC Yellow +12VDC Orange +12VDC Orange Key N/C Key N/C Coin Counter 2 Brown-Red Coin Counter 1 Brown Not Used N/C Not Used N/C ©]@|N] o/c] a] oo]ro]s Speaker -, Left Brown-Gray Speaker +, Left Red-Gray Speaker -, Right Brown-White Speaker +, Right Red-White Video Green Yellow-Green Video Red Yellow-Red Video Sync Yellow-White Video Blue Yellow-Blue Service Credits White-Gray Video Ground Yellow-Black Slam Tilt Black-Green Test Black-Blue Coin 2 Black-Red Coin 1 Black-Brown 2 Start Violet-White 1 Start White 2Up Violet-Black 1Up White-Black 2 Down Violet-Brown 1 Down White-Brown 2 Left Violet-Red 1 Left White-Red 2 Right Violet-Orange 1 Right White-Orange 2 Button A Violet-Yellow 1 Button A White-Yellow 2 Button B Violet-Green 1 Button B White-Green 2 Turbo Violet-Blue 1 Turbo White-Blue Not Used Violet Not Used White-Violet Not Used N/C Not Used N/C Ground Black -5V Ground Yellow-Brown Ground =] alo |o]m |N|<|x]/S]<|C]A]m| a] v)Zl=Z/-}Al}C |r} a) ml ojo|al>

Black Ground Black Solder Side of Circuit Board Component Side of Circuit Board

Control Panel Wires That Aren’t Part of Main JAMMA Harness Function SIO Bd, P14- Function SIO Bd, P7- 4 Digital Ground 3 Digital Ground +5 Volts Unused Unused 3/4/15 Unused 3/4/15 4 Start 3 Start 4 Stick Up, Bit 0 3 Stick Up, Bit 0 Blu-Blk 4 Stick Down, Bit 1 3 Stick Down, Bit 1 Blu-Brn 4 Stick Left, Bit 2 3 Stick Left, Bit 2 Blu-Red 4 Stick Right, Bit 3 3 Stick Right, Bit 3 Blu-Orn 4 Button A 3 Button A Blu-Yel 4 Button B 3 Button B Blu-Grn 4 Button C, Turbo 3 Button C, Turbo Blu 4 Button D (N/U) 3 Button D (N/U) Blu-Vio *Abbreviations: Bd = Board; NC = Not Connected; BIk = Black; Brn = Brown; Orn = Orange; Yel = Yellow; Grn = Green; Blu = Blue; Vio = Violet; Gry = Gray; Wht = White.

6-2

Page 104

Function Wires That Aren’t Part of Main JAMMA Harness Function Wire* SIO Bd, P23- Digital Ground Digital Ground Blk Output Bit 0 Coin 3 Blk- Orn Output Bit 1 +5 Volts Red Output Bit 2 +12 Volts Orn Output Bit 3 Unused Key Unused Coin 4 Blk-Yel Unused Dollar Bill Blk-Wht Unused Volume Down Om-Red Unused Volume Up Om-Grn ©]00|N] oo] on] A] oo ]ro] >

Unused Unused NC Unused Unused NC Unused Function Wire Color* Unused +12 Volts Orn Unused Digital Ground Bik Digital Ground Digital Ground Blk +5 Volts Red *Abbreviations: Bd = Board; NC = Not Connected; BIk = Black; Brn = Brown; Orn = Orange; Yel = Yellow; Grn = Green; Blu = Blue; Vio = Violet; Gry = Gray; Wht = White.

Function D.C. Power Source Voltage Limits Function Digital Circuits Audio, Lights Audio, DBV.

6-3

NOTE: +5V is adjustable at the Power Supply
Page 105

HITE

POWER WIRING DIAGRAM

NOTE MIE Lor IDE

IN FI Prone

rye HITE. By POWER Pron

EI q FN EL

MEL

ao FN EL

FUSE APPLICATION CHART

LTACE | FOCE LATING

ii}

6-4

NROL

PANEL

Page 106

CONTROL WIRING DIAGRAM (49-WAY JOYSTICK)

803 Sopp

eo,

Is\ HORIZONTAL

POSITION LOGIC TABLE

DIRECTIONFULLYMODERATELY | SLIGHTLYDEADSLIGHTLY | MODERATELY |FULLY
LEFTLEFTLEFTCENTERRIGHTRIGHTRIGHT
01110111011100110111000101110000011111000111111001411111
(00)(01)(02)(03)(04)(05)(06)
MODERATELY | 001101410011001100110001(00110000001111000011111000111111
uP(07)(08)(09)(10)(11)(12)(13)
SLIGHTLY(00010111(00010017(00010004(00070000(0001110000011110(00011177
uP.(14)(15)(24)(24)(24)(19)(20)
DEAD(000001140000001100000001‘00000000(0000110000001110(00001111
CENTER(21)(22)(24)(24)(24)(26)(27)
SLIGHTLY14000111140000141400000111000000110011001100111011001111
DOWN(28)(29)(24)(24)(24)(33)(34)
MODERATELY |111001171410001417100001771100000141011001410111011101117
DOWN(35)(36)(37)(38)(39)(40)(41)
FULLY14110114141100111411000111110000141111001111111014111114
DOWN(42)(43)(44)(45)(46)(47)(48)
NOTE: 1. Connector pin sequence for the above data is as follows: 9-8-7-6-5-4-3-2, referred to ground at pin 12.
  • Numbers in parentheses appear in the Switch Test. Program does not use the “slightly” positions.

6-5

Page 107

CABINET LOGIC WIRING DIAGRAM, PART 1

6-6

Page 108

CABINET LOGIC WIRING DIAGRAM, PART 2

6-7

Page 109

DOLLAR BILL VALIDATOR WIRING

6-8

Page 110

CPU BOARD INDICATOR AND SWITCH LOCATIONS

CPU BOARD SWITCH

Switch Location Function Positions State Meaning

s1* Edge Near U10 Resets and 2 Off Normal Operation and U12 Restarts Game On Forced Reset

*Notes This switch resets the CPU Board without shutting off power at the power supply.

6-9

Page 111

CPU BOARD JUMPER LOCATION TABLE

Jumper J3 J6

Located U28 & U22 & U27 Near... Connector P5

CPU BOARD JUMPER POSITION TABLE

Default

27C080, 1M X 8, EPROM

270040, 512K x 8, EPROM 27C010, 128K x 8, EPROM 29F040, 512K x 8, Flash 29F020, 256K x 8, Flash 29F010, 128K x 8, Flash

Expansion 27C080, 1M x 8, EPROM (u28) 270040, 512K x 8, EPROM 27C010, 128K x 8, EPROM

External Boot from CPU ROM

Boot Boot from SIO ROM

*Notes 1.-- = Not Applicable

  • Memory type numbers shown are for blank parts. Your game requires programmed parts.
Page 112

CPU BOARD LED INDICATOR STATUS TABLE

Location Function Meaning

Off Insufficient Power

Near U6, U7 & 3.3V CPU U16 Power On Power OK Indicator

Blinking Power Supply Fault Off Disk Not in Use

Near U28 & Hard Disk Connector P5 Drive On Locked Up Disk Activity

Blinking Normal Disk Activity

Off* Near U22 & Indicator See Note 3, Below. U26 On*

Blinking* Sequentially

Notes

  • LED1 monitors CPU power (+3.3 volts). If his LED is off or blinking, investigate processor circuits. If other LEDs are off or blinking at the same time, check +5-volt circuits or the game power supply.
  • LED2 flashes when the hard disk is operating during game play. LED2 may light continuously during startup. If this LED remains lighted, the hard drive may be locked up or faulty.
  • Software controls RP63. In this game, RP63 initially indicates program startup stages. This LED is a sevensegment, alphanumeric display device. Normally, RP63 displays a lowercase “b,” or an “O” pattern with sequentially blinking segments. During Self-Test screens, RP63 displays a “bouncing bar” that resembles a hyphen (“-").
Page 113

SOUND I/O BOARD ASSEMBLY A-23431-2

6-12

Page 114

Jumper SOUND I/O BOARD JUMPER POSITION TABLE *

Location Function Meaning Position J1 (Note 1) Near U9 & Crystal Y3 1/0 Connector P2 Input Mode Pins 1&2

Output Mode Pins 2&3

J2 Between U35 & U10 Video Sync Positive Sync Jumper Not Installed

Negative Sync Pins 1&2

J3 (Note 2) Near U15 1/0 Connector P4 Input Mode Pins 1&2

Output Mode Pins 2&3

None None Not Used None Between U15 & Connector P2 1/0 Connector P4 Input Mode Pins 1&2

Output Mode Pins 2&3

None None Not Used None None None Not Used None

(Note 1)

Notes Between U9 & Connector P4 /O Connector P2 Input Mode Pins 1&2

Output Mode Pins 2&3

  • Configure I/O port P2 by setting both jumpers J1 and J8 to input or output mode.
  • Configure I/O port P4 by setting both jumpers J3 and J5 to input or output mode.
Page 115

LED SOUND I/O BOARD LED INDICATOR STATUS TABLE

Location Function State Meaning

LED1 (Note 1) Near U11 Not Used (Remains Off) Off On Blinking

LED2 (Note 2) Near U34 & Crystal Y¥1 Linking Connector Status Off Not in Use (No Game Linking)

On Link Continuity Good

LED3 Near the JAMMA Connector -5V Power Indicator Off* No Power

On* Normal Operation

(Note 2) Near U35 & Connector P14 +12V Power Indicator Off No Power On Normal Operation LEDS (Note 2) Near Connector P23 +5V Power Indicator Off No Power On Normal Operation

LED6 (Note 2) Near U34 & Crystal Y1 CPU Linking Activity Off Not in Use On CPU Communicating with Ethernet Controller

LED7 (Note 2) Near U34 & Crystal Y¥1 Linking Transmitting Data Off Not in Use (No Game Linking) On Sending Data Blinking Normal Operation

LED8 (Note 1) Near U14 & Crystal Y¥1 Audio Activity Off No Sound Boot ROM On Locked Up Blinking Normal Operation LED9 (Note 2) Near U34 & Crystal Y¥1 Linking Receiving Data Yellow Off Not in Use (No Game Linking) On Receiving Data

LED10 (Note 1) Near U44 & Crystal Y2 Not Used (Remains On) Green Off On Blinking

LED11 (Note 1) Near U44 & Crystal Y2 Not Used (Remains On) Off On Blinking

LED12 (Note 1) Near U44 & Crystal Y2 Not Used (Remains On) Off On Blinking

LED13 (Note 1)

Notes Near U44 & Crystal Y2 Not Used (Remains On) Yellow Off On Blinking

  • Software controls this LED. Indications are game and revision-specific. Changing the EPROMs on this board may alter the function of this LED. Firmware damage may also cause new of different LED behavior.
  • Hardware controls this LED. Indications depend on hard-wired circuitry. A change in normal LED behavior may indicate a circuit fault. Changing the EPROMs on this board shouldn't alter the function of this LED.

6-14

Page 116

VIDEO BOARD INDICATOR AND SWITCH LOCATIONS

Note This video board has no jumpers or LEDs.
Page 117

NOTES

Page 118

SPORTSTATION

CHAPTER

SEVEN

TROUBLESHOOTING

NOTICE: The term VGM refers to the video game machine.

& CAUTION: This VGM uses complex electronic components that are very sensitive to static electricity. Observe the following precautions before handling VGM electronics. Failure to do so may void your warranty and could damage electronic assemblies.

Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge. Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge this static, begin by connecting the line cord to a grounded outlet. Don’t turn on the VGM! Next, touch the safety ground stud of the power supply chassis. Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport VGM circuit boards. Transport the hard drive in its shipping container. Don’t remove or connect electronic assemblies when cabinet power is on. Otherwise, you'll damage electronic assemblies and void the VGM warranty. After you complete maintenance or service, replace ground wires, shields, safety covers, etc. Install and tighten ground and mounting screws.

7-1

Page 119

Coin Mechanism and Pricing Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION ‘ From Coin Options Menu, choose PRICING

+VGM (video game machine) | preinywieru S|OPTIONS MENU. Verify that units and credits

accepts currency or tokens, are set correctly.

  • Consult bill validator manufacturer's literature. Adjust pulse width on validator to long setting. Retest validator operation. but number of credits per ia Incorrect pulse width coin or bill is incorrect. on bill validators ais Check that cabinet wiring is correct for this VGM.
Faulty wiring2.Assure that coin meter and coin switches

connect properly to control input wires.

  • Verify that coin mechanism works correctly by Ue dace testing it in working VGM. .__ If mechanism is bad, replace it.
  • Unlock and open cash door. Empty cash box. y Inspect revenue for counterfeit currency.
.Wee worl accept anandImproper currency2.Check vault. Remove any items that biock path

, from mechanism.

«VGM won't start.1.Unlock and open coin door. Check each
*Audio and video are present.2mechanism tor probes mounting.
Faulty coin3.Clear currency path.
aachantom4.Reinstall mechanism and latch it.
  • Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Main Menu, choose CONTROLS TEST. Use tests to confirm operation of coin switches.
  • Verify that mechanism is level after doors close. Tilted coin Repair or replace coin door if it is bent or damaged.
  • If necessary, adjust cabinet leg levelers to keep mechanisms vertical. mechanism or VGM
  • Burned-out bulbs may appear white or darkened.
© — Coin indicators don’t lightBurned-out bulbCheck continuity with DVM.

Replace burned-out bulb with same type. Check fuse continuity with DVM. If fuse is blown, replace fuse with same type. If fuse isn't blown, check wiring. Open fuse circuit YN>AIN

CAUTION: Don’t remove or install any connector when power is turned on. Installation under power will damage the circuit boards or hard disk drive and void the warranty.

PRICE INDICATOF

REJECT FLAl

Typical Coin Mechanism Mounting

7-2

Page 120

VGM Startup Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

  • Check that VGM power switch is on.
«—VGM (video game machine)2.Inspect electronics to see if fans are turning. /f
doesn't start.Power problemnot: Is power supply connected to its power

cable? Is power supply turned on?

«VGM appears completely3.Plug VGM into AC power outlet. Verify presence

non-functional. of AC line voltage.

*NoaudioImproper line voltageTurn off VGM power. Unplug AC line cord. Check

line voltage switch. If necessary, set it to agree switch setting with local AC line voltage. Retest VGM. ¢ No illumination . . 1. Turn off VGM power. Examine AC fuse on power

*No video displaysupply.
Open fuse2.Examine DC fuses inside coin door vault.
  • Replace faulty fuses with identically rated parts.
  • Turn on VGM power. If fuse opens again, check DC wiring harness and connectors.
  • Remove line cord. Test line cord, power plug, and IEC connector for breaks or damage. Verify continuity of each wire in cord. Install cord at power chassis. Press connector firmly to seat it.
Faulty wiring2.Check other cables in same manner.
  • Assure that cabinet wiring harness connectors fully seat in corresponding power supply and board connectors.
  • Inspect wiring for breaks or damage. a Turn off power for one minute and turn VGM on Faulty circuit boards again. Power On Self-Test checks electronics.

FLORESCEMT | — UGHT Butt

nerter|

oa Lek benitor — “ 1euney ACCESS. OOK | 0

une on Ge ener 4 SPPUCATION | p He & | — Fan Guar

imey, — : wn u beni — AbINET > — honimer 2b. STHENT Boar

cover — EL GASTE! = eee

Typical Location of Power Supply and Line Cord

7-3

Page 121

VGM Startup Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

« VGM (video game machine) appears non-functional.

«Currency acceptor price indicator is illuminated. Power problem

  • Inspect circuit boards under low-light conditions. LEDs glow if processor circuits receive voltage. Fan should be turning. These indications prove presence of DC from power supply. Still, voltages or signals may not be normal.
  • Turn on VGM power. Using 20-volt DC setting on digital voltmeter, measure DC voltages at power connector pins.
  • Using 2-volt AC setting on digital voltmeter, measure same DC voltages as above. Any reading indicates ripple or noise. In that case, service power supply.

Faulty wiring Turn off VGM power. Assure that wiring harness connectors attach and fully seat onto mating board connectors. Improper jumper or DIP switch settings Verify that circuit board jumpers are set as intended. Check DIP switch settings.

Faulty circuit boards Run power-up self-test sequence. Note errors or failures during tests. Compare LEDs with LED indicator status —_—_charts. Note discrepancies.

CAUTION: Don’t remove or install any connector while power is turned on. Doing so will damage circuit boards or hard disk drive, and void warranty.

PRICE INDI

—PESECT FLé¢l

Front View Of Coin Door AT

7-4 Interior View Of Electronics

Page 122

VGM Startup Troubleshooting Table, continued

tokens.

« Audio and video are present. SYMPTOM CAUSE REQUIRED ACTION Unlock and open coin door. Check each ¢ VGM (video game machine) currency acceptor to assure proper mounting. doesn’t start. Verify that each release latch is closed and locked. Does mechanism accept and reject F > Se © —VGM accepts currency or Faulty coin currency correctly? Test mechanism with good mechanism and bad coins. Inspect to see if external acceptor indicators (Pricing, Flashing Arrows, etc.) are lit. Verify that each acceptor operates properly by placing it in working VGM. Replace bad parts.

Faulty switches Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Main Menu, choose CONTROLS TEST. Use tests to confirm operation of each switch. Assure that no loose parts or wires are caught in switch contacts. Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed). Replace faulty switches (bent levers, broken actuators, etc.).

Faulty wiring Assure that no wires are caught in hinges, latches or switch contacts. Check wiring continuity from circuit board connectors to acceptors.

Interior View of Coin Door and Cash Door

7-5

Page 123

Audio Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

  • From Main Menu, choose VOLUME LEVEL. No audio Check that Attract Music is on (enabled). Verify

Video is present

VGM (video game machine) appears to operate normally Improper volume setting that all volume levels are set well above zero. If necessary, change levels to make VGM audible.

Faulty SIO Board From Main Menu, enter Diagnostics Menu.

SelectSOUNDSUBSYSTEMTEST.Test

checks entire sound system. Run power-up self-test sequence. Note errors that VGM finds during tests. Compare Sound I/O Board (SIO) LEDs with LED indicator status charts. Note discrepancies. Verify proper operation of SIO Board by placing it in working VGM. If board is faulty, replace it.

Constant low hum from all speakers. Faulty wiring nals Check that cabinet wiring is correct for this VGM. Verify that cabinet wiring provides separate wires (not common return) for each speaker. Check connection of all cabinet ground wires.

Faulty power supply Using 2 Volt AC setting on digital voltmeter, measure voltages at speaker terminals. Any reading indicates ripple or noise. In that case, service power supply.

Audio is distorted, muffled or has missing frequencies. Faulty or improper speaker Turn off VGM power. Remove grilles and check speakers. Assure that speakers are full range (100 to 10,000 Hz response) and rated for at least 20 watts. Woofers must be rated for at least 40 watts. Verify proper speaker operation by connecting speaker in question to working VGM. If speaker is faulty, replace it.

Faulty wiring

Multiple-speakerinstallations: | Checkfor

reversed wires at one speaker. Weak low frequencies and thin or hollow sound quality is symptom of incorrectly phased speakers. Sound tests may not detect this condition, but you can hear it during VGM operation.

Dead sound channel Faulty speaker From Main Menu, choose SOUND TEST. Recheck speakers with audio signals provided by test. Verify proper speaker operation by connecting speaker in question to working VGM. If speaker is faulty, replace it.

Faulty circuit board From Main Menu, enter Diagnostics Menu.

SelectSOUNDSUBSYSTEMTEST.Test

checks entire sound system. Run power-up self-test sequence. Note errors that VGM finds during tests. Compare circuit board LEDs with LED indicator status charts.

Note discrepancies. Verify SIO Board operation by connecting board to working VGM. If board is faulty, replace it.

Faulty wiring Verify that cabinet wiring is correct. Assure that all speakers connect to audio wires. Check for broken or shorted wires.

7-6

Page 124

Joystick Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION Enter game Menu System by pressing and ¢ Players complain that holding TEST MODE switch inside coin door.

joystick operates erraticallyFaulty switchFrom Diagnostics Menu, choose SWITCH TEST.

or unreliably Operate joystick in question. Check for proper readings of up, down, left and right.

¢Game starts normally1.Check for wires caught in door hinges, latches or

switch contacts.

  • Verify that harness connectors are attached and fully seated.
Faulty switch wiring3.Assure that joystick switches connector properly

to control input wires.

  • Check joystick cable ground connections.
  • Check that cabinet wiring is correct for this VGM (video game machine).
  • Inspect joystick for: Missing, loose or damaged Faulty mechanical parts, torn rubber T-band, etc.
parts2.Replace bad parts.

Clean dust out of optos with swab and cleaner. Dirty optos Don't apply cleaner directly into opto. Never use solvents! Check fuses on 1-40 Joystick Interface Board Faulty joystick fuse inside player control panel. Each joystick has its own fuse.

  • If joystick fuses are okay, install joystick in Faulty joystick working VGM (video game machine) and retest electronics it. If joystick still doesn’t work, replace it.
  • If joystick works in second VGM, I-40 Joystick Interface Board may be bad.
  • Replace board and retest joystick. Faulty I-40 Joystick Interface Board

er ewer —H-F Erne

Tok top, PLACE paces PT boat Loner vo

Joystick Parts

7-7

Page 125

Video Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

«Monitor appears nonfunctional

e Audio is present

« VGM (video game machine) controls operate normally Power problem Verify connection of AC Power to video monitor. Inspect CRT neck in dim _ light. Glowing filament near CRT base proves that some monitor circuits receive power. Still, voltages or signals may not be normal.

Faulty wiring Turn off VGM power. Verify that video signal and Remote Adjustment Board connectors seat properly on Video Monitor Board. Assure that video cables connect to circuit boards. Assure that no wires are caught on chassis or mounting brackets. Improper monitor adjustments Check that BRIGHTNESS (intensity) and CONTRAST are set above their minimum levels.

Faulty monitor circuitry Examine AC line fuse on Video Monitor Board. If fuse is faulty, replace it with identical fuse. If fuse is good: Verify that video monitor operates correctly by placing it in working VGM. If monitor is bad: Check monitor power supply. If power supply is good: Check monitor horizontal output transistor and related circuitry.

WARNING: HIGH VOLTAGE. VGM monitors generate and store potentially lethal high voltages. Avoid touching any part of the monitor until power has been off for some time. A picture tube can maintain a hazardous charge for up to several days. Only qualified technicians should service monitors. Turn off the power, unplug the VGM and discharge the CRT before attempting service. Even properly discharged tubes can revert to a highly charged state, without reapplication of power.
WARNING: In normal operation, the monitor doesn’t require isolation from AC line voltage. During bench servicing, you may need to operate the monitor outside the cabinet. If you do, isolate the monitor from line voltage with an isolation transformer.
CAUTION: Don't operate the monitor without the Remote Adjustment Board.

vent; —

ak mor spac stueNT wo

Page 126

Typical Cutaway Rear View

7-9

Page 127

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

« Game screens don't appear

  • No audio

« Power-up self-test runs Improper compont ents Verify that hard disk drive is correct for this VGM (video game machine). Label on drive records manufacturer name, assembly number and program version. Verify that circuit boards are correct for this VGM. Label on each board records manufacturer name, assembly number and hardware version. Verify that ROM instruction set is correct for this VGM. VGM set only has one ROM. Label on ROM records assembly number and software version.

Hard drive problems Turn VGM on. Immediately look under hard drive. Hard Drive Activity LED flashes if drive is operating properly. Allow VGM to load normally. Note and record any error messages that occur during self-test. Remove hard drive and install it in working VGM. If symptom recurs there, hard drive is faulty. Replace it.

« Blotches of color appear on screen Picture tube aperture mask is magnetized Remove diskettes from room. Demagnetize monitor with external degaussing coil. Take care not to magnetize neighboring VGMs. Monitor may be on or off for this procedure.

¢ White areas in center of screen appear tinged with color

*¢ Object edges have fringe of one or more colors Picture tube purity or static convergenc out of alignment e is ad Turn on VGM (video game machine). Press and hold TEST MODE to enter Menu System. At Main Menu, select Monitor Tests Menu. Run through Crosshatch, Red, Green and Blue screens to find clearest display of problem. Display screen with greatest problem. Display Crosshatch Screen. Locate purity and static convergence ring magnets on back of monitor neck. Watch screen in mirror. Adjust magnets to minimize problem. Follow instructions from monitor manufacturer. Display Crosshatch Screen. Touch up adjustments while watching screen in mirror.

« Background of Attract Mode screens seems out of sync

« Words on screen read OK Someone set DIP switch for resolution lower than VGA VGM only outputs VGA video. Press and hold TEST MODE to enter Menu System. At Main Menu, select DIP Switch Test Menu. Locate DIP switch bank U12 on the Sound I/O Board. Turn off switch 2. Reenter Attract Mode and check screens.

CAUTION: Don't operate the monitor without its Remote Adjustment Board.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.
Page 128

Video Troubleshooting Table, continued

SYMPTOM CAUSE REQUIRED ACTION

White areas at screen edges appear tinged with color

Dots at screen edges appear oval or cylindrical Picture tube dynamic convergence is out of alignment Have service bureau dynamically reconverge monitor. This procedure requires removing and repositioning yoke. Service bureau must follow instructions from monitor manufacturer.

Video tears or rolls, or has black bar down middle of screen Faulty wiring

Checkconnectorsandcablesforwiring

continuity. Video cables connect graphics card to circuit boards, and then to video monitor. Assure connection of all cabinet ground wires, especially at video monitor chassis.

Faulty monitor circuitry Check video monitor operation by connecting it to working VGM (video game machine). Assure that video monitor is correct type for this VGM. Video monitors with wrong resolution can’t lock sync.

Improper sync signals er Check to see if Video Board puts out type of sync that your monitor requires. Verify that jumpers are set correctly for monitor. If necessary, add or remove video sync jumper at Sound I/O Board jumper block J10. With no pins connected (or pins 2 and 3 connected), board outputs positive sync. With pins 1 and 2 connected, board outputs negative sync.

Electromagnetic fields

Movecabinetfarawayfrommachines,

appliances, or competitors’ VGMs.

Missing colors Faulty wiring

Checkconnectorsandcablesforwiring

continuity from circuit boards to video monitor. Faulty monitor color drive circuitry Verify that video monitor operates correctly by connecting it to working VGM.

One color is dimmer or brighter than others

Whites appear tinted everywhere on screen Maladjusted color bias pots PONS

ao Turn on VGM (video game machine). Enter Monitor Tests Menu. Watch Color Bars screen in mirror. Adjust three bias pots for best colors. (Most monitor neck boards include these pots.) Also check White Screen. Touch up controls. If whites still seem tinted, have service bureau rejuvenate picture tube.

Picture is dim or faded Maladjusted BRIGHTNESS pot or subnormal picture tube emission Watch Color Bars screen. Adjust BRIGHTNESS and CONTRAST pots for greatest number of grays. You'll find these pots on Monitor Remote Control Board, behind coin door. If pots have no effect, have service bureau rejuvenate picture tube.

Picture is too narrow Maladjusted WIDTH pot Enter Monitor Tests Menu. Watch Crosshatch Screen while adjusting WIDTH pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.

Picture is too short Maladjusted HEIGHT pot or damaged vertical circuit Enter Monitor Tests Menu. Watch Crosshatch Screen while adjusting HEIGHT pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door. If pot has no effect, service vertical output circuit.

Picture seems shifted to one side Maladjusted HORIZONTAL POSITION pot Enter Monitor Tests Menu. Watch Crosshatch Screen while adjusting HORIZONTAL POSITION pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.

Page 129

Keystone-shaped picture Shorted turns in yoke 1. 2. 3. Substitute working yoke. Have service bureau converge monitor. Retest monitor.

7-12

Page 130

Software Update Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

« Update didn’t work

e After update procedure, You skipped steps or performed them out of sequence. Return update components to kit, reinstall original parts in cabinet, and try process again.

screen reports lower thanInstallation error may | 1.Inspect for bent or broken pins.
latest verionhave damaged2.If you have another kit, try it.
device.3.__Ask your distributor to check your floppy disk.
7Onceyou'veupdateddiskdrive,CPU
¢No Attract Mode screenslelhapelade ainstructions must be at correct version to make

update version and f B A

Board indicators illurniriatehard drive.use of new data stored on disk.Be certain that

° f , boot ROM device resides in proper socket. but screen is completely

blank1.Install disk ROM. Only use upgrade socket for

You may have hard disk drive updates. During game play, installed devices in upgrade socket must be empty.

wrong sockets.2.Load ROM contents onto drive.
  • Remove ROM from game.

NOTICE: Someday, software updates for your VGM (video game machine) might become available. These upgrades may improve your VGM’s performance or add new VGM features. Such upgrades tend to appear sometime after the factory first releases the VGM. Contact your distributor for information about updates.

Page 131

Miscellaneous Problem Troubleshooting Table

SYMPTOM CAUSE REQUIRED ACTION

«Marquee lamp is intermittent or non-functional

« VGM (video game machine) starts and plays normally Faulty fluorescent tube Remove fluorescent tube from its sockets. If you find cracks or darkened ends, install new lamp. Clean tube. Check continuity of both fluorescent tube filaments. Verify that fluorescent tube operates by placing it in working VGM.

Faulty lamp fixture Verify that lamp pins make good connection with socket contacts. Check ballast for continuity.

Faulty wiring Measure fluorescent lamp AC voltages. Check wiring and connector continuity from AC power chassis to lamp assembly. If you find faulty wiring, repair or replace it.

« VGM operates normally

  • Cabinet becomes warm after several hours of use Obstructed fan Check bottom and rear of cabinet for blocked airflow. Move VGM away from sources of heat. Turn off VGM power. Remove dust from vent holes with high-power vacuum cleaner.

Faulty wiring Check fan wiring and connectors. If you find faulty wiring, repair or replace it.

Faulty fan Check operation of all fans, including power supply fan. If fan is faulty, replace it.

« Error messages appear on screen Faulty hardware Check any assembly (RAM, ROM, Battery, etc.) identified in error messages. Call your authorized distributor for help with unresolved screen messages.

f Fan Location and Mounting

7-14 J FAN ASS EMBPL ROE FL REVE!

Page 132

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 133

WARNINGS & NOTICES

WARNING e Use of non-Midway parts or circuit modifications may cause serious injury or equipment damage! « Use only Midway authorized components and parts. Failure to do so will void your warranty and may result in incorrect or unsafe operation. Substitute parts or modifications may void the EMC directive or FCC type acceptance. « Federal copyright, trademark and patent laws protect this game. Unauthorized modifications may be illegal under Federal law. The modification ban also applies to Midway Games Inc. game logos, designs, publications and assemblies. Moreover, facsimiles of Midway equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with Midway Games Inc. components.
WARNING Prevent shock hazard and assure proper game operation. Plug this game into a properly grounded outlet. Do not use a cheater plug to defeat the power cord's grounding pin. Do not cut off the ground pin.
WARNING A very small portion of the population has a condition which may cause epileptic seizures or momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition. If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g. seizures or loss of awareness), immediately consult your physician before using any video games. We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, discontinue use immediately and consult your physician.

NOTICE This video game machine has been tested. It complies with limits for a Class A digital device, under FCC Rules, Part

  • These limits provide reasonable protection against harmful interference when the equipment operates in a commercial environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to the instruction manual, this equipment may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference. If interference occurs, the user must correct it at his own expense.

NOTICE You may not reproduce any part of this publication by mechanical, photographic, or electronic means. You may not prepare phonograph recordings of this document. You may not transmit this publication or otherwise copy it for public or private use, without permission from the publisher. COPYRIGHT & TRADEMARK NOTICE Entire contents of this manual copyright © 1999 Midway Games Inc. All rights reserved. The following are trademarks of Midway Games Inc.: Midway®, SportStation™, NBA Showtime™, NFL Blitz 2000 Gold Edition™. ©1999 NBA. ©1999 NFLP. Team names and logos are trademarks of indicated teams. The NBA logo is a trademark of the National Basketball Association. Officially Licensed Product of the National Basketball Association. The NFL shield, Super Bowl and Pro Bowl are trademarks of the National Football League Players. The Players Inc. logo is a registered trademark of the NFL Players. FOR SERVICE Call your Authorized Midway Games Inc. Distributor.

MIDWAY GAMES INC., 3401 N. California Ave., Chicago, Illinois 60618-5899 USA