CATHODE RAY TOMES

Tempest Cabaret ST-196 1st Printing Backdoor Sheet

Tempest (rev 3, Revised Hardware) (Atari, 1980) · Backdoor Sheet · 1 pages · original scan

Page 1

Self-Test Procedure

The information below is displayed on the screen if you set the self-test switch to on during the attract mode. Look at the

displayed numbers for SECONDS ON and SECONDS PLAYED. It

these numbers run together vertically, make adjustments to the X-BIP and Y-BIP potentiometers on the game PCB. To go to Self-est Part 2, rotate the control knob until the message PRESS FIRE AND SUPERZAPPER FOR SELF-TEST appears on the monitor. Then press both FIRE and SUPERZAP- PER. To end the operator information display, set selt-test ‘switch to off.

TIME GAME ON

Important Note to Operator

If the operation, maintenance and service manual or troubleshooting guide was not included in this game when you unpacked it, contact your distributor to get a free copy. (All Atari manuals for coinoperated games also include complete illustrated parts lists.) ST-196 1st printing

(Seconds)

TIME GAME PLAYED (Seconds)

No. OF ‘PLAYER GAMES.

No. OF ‘COIN MECH 2.LAYER GAMES MULTIPLIER ivennee ‘SWITCH AT N13 SOMETIME

{Coin Modes) BONUS ADDER SO0O000C —s

suetooo0o000yoaGLe®

oo0000o0 SWITCH AT L12

(Game Play)SRSTSwiTcH ar Diez
iveswot(Game Difficulty)

PER GAME Sunt etear CAME Game Option Settings

CREDITS20FRRR.a;‘To change toggle positions on the switch assemblies, you needWhen changing the options, verity proper results on the moni:
COIN MODEnot remove the game PCB, The switches ae accessible when thetor display by performing the selttest, Note that changing an op-
WoreLANGUAGETempest" Analog Vector-Generator PCB is mounted in place. To_tion on any of the following eight toggles will not cause an imme.
Or OFpennfechange postions on th Autry PCB sige the Beard ou ae fardale change on the montorsren ing the att mde

as possible. ‘SWITCH

Operator Information Display

‘To erase High Score Table: To erase Game Times:

4. Turn control knob until top line reads PRESS FIRE AND41.Turn control knob until top line reads PRESS FIRE AND

‘START 2 TO ZERO SCORES. START 1 TO ZERO TIMES.

2. Press both FIRE and START 2.2.Press both FIRE and START 1.
  • The word ERASING appears and blinks on the screen until 3. The word ERASING appears and blinks on the screen until ‘he entire table is erased. Walt until the word ERASING disappears before continuing with other tests. the entire table is erased. Wait until the word ERASING disappears before continuing with other tests.

Instruction Test Passes switch to on . Press

‘After about 5 secconds, the monitor dis plays the picture below. No sounds are Tost Falls RAM FAILURE is indicated by a sequence of 1 to 12 tones and an A displayed in top half of screen. You will hear a short low tone and see a short flash on the LED start pushbutton for each good RAM chip, and a long high tone accompanied by a long pulse on the start pushbutton for a falling RAM chip. The test stops withthe first fall-

  • Sot selftest

RESET on the PCB, or turn power off

and-on egainproducedIng RAM, To resta the sequence, prose RESET on the PCB, or power game to aff

then toon again Identity the bad RAM chip with the table below. Example four snort a tow tones followed by along high tone inccates flue of RAM at location MS. A010" ening ware FRAME Bad RAM Chip Location WotoLe Ano warm ,

pot arVISIBLE AND WITHINLong High Toneon Analog Vector Generator PCB
aAstRZ

nd Pe ‘ad fa

rosaathPa
roa'Benesthws
SenaihMa
swircu artx2onis
rns.‘aqonOGAT[sensiainiv)
Sinha)soooo000TON AT oman3
|0Dificulty)0thKa
‘START 21900CONTROLath8
ZCi‘2th4

START.

FIRE: RIGHT COIN MECH ROM FAILURE!s indicated by a vertical pair of hexadecimal numbers on the top of the screen. The top number indicates the location of the failing ROM(s). Ignore the bottom LEFT COIN MECH hexadecimal number in the pair. Identify the bad ROM with the table immediately SUPERZAP uri coin switcH Below

ae anUtepaged WoBad ROM Chip LocatonPCB Location

A Pt 8 MINt

8umt‘Analog Vector.
7KIGenerator PCB

6 at 5 at 4 FY 3 e 2 on 4 Fo o NiPS* EAROM, Audio and Math Box Failure are indicated by a single letter in the center of the display. Identity the fllure withthe table below.

Displayed Letter Failure PCB Location

EEAROM3 (Aux. PCB)
PpAudio 1B/C2 (Aux. PCB)
QAudio 2C102 (Aux. PCB)

R RAM ‘See RAM test above M Math Box**

“if this ROM is bad, you will near a continuous low tone, and the program may be unable to display a screen image. ** Math-box failure is explained in TM-195, Tempest Troubleshooting Guide.

2 Activate start,

fire, Superzap,‘As switch activates,You will not hear a beep and 0 will remain on the screen for the defective switch.

SLAM, and coin you'll hear a beep and switches.* O changes to 1 on the screen.

3, Rotate encoder wheel clockwise and counterclockwise. The right hexadecimal ‘umber on the screen will increase with counter clockwise mo- Qn, and decrease with clockwise motion. Incorrect progression of numbers indicates encoder wheel harness wires were con: nected incorrectly. No number change indicates encoder wheel is bad or harness. wires are loose.

  • Observe the white frame around the outside of the screen. Each frame corner should be within Ye-inch of each monk tor bezel comer. Consult Tempest™ Drawing Package to adjust video pots.
  • Activate SLAM switch. A white cross hatch pattern appears. A character set appears, at the bottom of the screen If display is not centered and symmetrical on the monitor, adjust video pots (see ‘Tempest Drawing Package) on the main PCB. If character set is incorrect, check Veo tor ROMs (see Troubleshooting Gui
  • Activate SLAM switch, Horizontal and vertical lines eross in the center of the screen displaying a large “plus” sign. Audio UO 1 and 2alternate to produce four tones. 'No sound indicates failure of an audio amplifier andlor the custom audio chipis).
  • Activate SLAM switch, Tests purple, cyan, yellow, white, green, blue, and red for color and intensity. Displays, ‘Seven groups of vert: cal lines, each with right line the brightest and left line the dimmest. Use this pattern for tracking adjustments (see the Color X*¥ Monitor Manua).
  • Activate SLAM switch, ‘A checkerboard pat term touches the sides and corners of the ‘monitor. Rotate the control knob to ‘change color. Use this pattern for purity and convergence adjustments (see Color XY. Monitor Manual,
  • Activate SLAM switch. ‘A white frame is displayed on the screen.
  • Wien satisfied with tes: set self: test swish to off position.

“Activate coin switches by inserting at least one coin in each coin siot. You will not trip the coin counters as long as you are in sel-test. Settings of @-Toggle Switch on Tempest Analog Vector-Generator PCB (at L12) 8 Option

23&§67

UTILITY COIN On On on off off On VOLUME Cu off Off

OnOnOffa
OnOnOn
OnOfOn
onofoft
OffOnOn
ofonof
ofoffOn
ofoffoff

on oft On On on off of On

Settings of 4Toggle Switch on Auxiliary PCB (at D/E2).

of off Ot On On off

3OnOn

3 oon Fa

On On oft ‘credit minimum $ 2-credit minimum,

English $ French German Spanish Bonus life granted at every: 10,000 points 20,000 points $ 30,000 points 40,000 points {50,000 points £60,000 points 70,000 points No bonus lite

2ilves per game 3ilives per game $ 4 lives per game S lives per game

Game ditficulty* Medium $ Easy Hard Medium

Starting Level 4,3,5,70r9 $ 1,3, 5, 7,9 or 11 if current high score 300,000-499,909 4,3,5,7, 8, 110 19 if current high score $500,000-699,990 41,3, 5,7, 9, 11, 13 oF 15 if current high score ‘more than 700,000

$ Manulacturer's suggested settings

  • Easy—Enemies move slower and one less enemy shot on the soreen at one time. Hard-—One more enemy, enemies move faster and 1-4 more ‘enemy shots on the screen at one time. ‘Changing toggles 1-5 erases the high, score table.

Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters}

Toggle Setings of 4Togole Switch on Analog Vector Generator PCB (K10/11) ‘Two coin acceptors 4382 4 in the coln door

OnOffBoth acceptors activate al coin count

ers simultaneously

Bg On_—_Bath accaptors activate 2 counters

z63separate.$8

on 2 3

5S5ootBath acceptors activate 2 counters

, separately wi On On_—_Bath acceptors activate al coin count ers simultaneously. $

'$ Manufacturer's suggested settings for games with 1 coin counter {$$ Manufacturer's suggested settings for games with two coin counters.

Game Price Settings The able below-contains the switch settings for options relating to game price, coin mechanism muttipliers (German coin doors), bonus play, demonstration and freeze mode. ‘The Demonstration Mode allows you to shoose any level (1-81) in the ready-to-play mode and accelerate through as many as 29 levels without having to kill the enemies. The Demonstration: Freeze Mode* * allows you to stop the action. The scores zeroed at the end of the game in this mode. ‘Set the toggles per the table below for the Demonstration Mode. Next, rotate the control knob. You may choose level 1 through 81 during the ready-to-play mode. Press either START button to accelerate through the tubes. Press the FIRE button to clear the spikes at the bottom of the tube. To freeze play, set switch 1 to off.

‘Toggle Settings of Toggle Switch on Tempest ‘Analog Vector-Generator PCB (at N13) 1 2 3 4 5 6 7 8 Option

of oft On On off

off

On On off off ‘on off On ott

Off

On

ott

off

On oft

On

on

Demonstration and A ‘ot oft or oft on ott On Free play 1 coin* for 2 credits 1.coin* for 1 credit $ 2eoins* for 1 credit

Right coin mech x 1. $ Right coin mech x 4 Right coin mech x 5 Right coin mech x 6 Left coin mech.x 1 $ Left coin mech x.2 No bonus coins $

For every 2 coins inserted, game ‘ogic adds 1 more coin*

For every 4 coins inserted, gam slogic adds 1 more eain* For every 4 coins inserted, gare logic adds 2 more coins* For every 5 coins inserted, g me logic adds 1 more coin* For every 3 coins inserted, c ame logic adds 1 mote coin* Freeze Mode**

Demonstration Mode Demonstration-Freeze Mode ATARI '$ Manufacturer's suggested settings

  • In the US, a “coin” Is defined as 258. In Germany a “coin” is 10M. ** If you press RESET during this mode, game will lock up. To recover, set switch 1 to on. To achieve bonus plays, all coins must be inserted before pressing start button.