Final Lap TM-325 1st Printing
Final Lap (Rev E) (Namco, 1987) · Technical Manual · 64 pages · 65 sections · original scan
GAMES
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAMES
Final Lap
Operators Manual
with Illustrated Parts Lists
Final Lap Upright
© 1988 by Atari Games Corporation. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams,.and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. “
Published by: Atari Games Corporation. 675 Sycamore Drive P.O, Box 361110 . Milpitas, California 95035
Printed in the U.S.A 9S
Produced by the Atari Games Technical Publications Department. Technical Writing: Rosalind Hutton Editing and Design: Andrea Dencker Illustration: Mary Ohanessian Sumner
Final Lap Upright
Notice Regarding Non-Atari Parts
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: ¢ Substitute non-Atari parts in the game.
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.
- The power cord is properly plugged into a grounded three wire outlet.
- On games provided with an Electromagnetic Interference (EMI) ground cage, be sure the printed-circuit boards (PCBs) are properly installed in the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area,
iii
Table of Contents
Set-Up How to Use This Manual Inspecting the Game... Installing the Attraction Sign... Connecting Cabinets. Choosing the Car Type Control and Switch Locations Setting the Coin and Game Options Game Play... Self-Test eregarenereserey Voki wn
Gas Pedal Test Brake Test Steering Wheel Test Sound Test Coin Options Difficulty Level Number of Laps... Communication Circuit Test Linked Game: Car Type... Motion Test .. Test Pattern Reset the High Score Table
Maintenance Preventive Maintenance Maintaining Your Game .. Opening the Control Panel Maintaining the Steering Wheel Asse: Lubricating the Gear Shift Assembly. Maintaining the Pedal Assembh Cleaning the Coin Mechanism .. Cleaning the Interior Components . Repairs ... ve Replacing the O-Rings on the Steering Wheel Stop. If the Steering Wheel Does Not Return to the Center.. PPP PRP YH YP YY PNY PD SHHHwKHHSHKYNYKKN
WROESRY EN WR BPWOWWWW YY
Replacing the Spring on the Steering Wheel Assembly .. 3-8 Replacing the Stop on the Steering Wheel Assembly... 3-8 Replacing the Steering Wheel Potentiomete: 3-9 Replacing the Steering Wheel 3-9 Replacing the Gear Shift Assembly. 3-9 Replacing the Microswitch on the Gear Shift Assembh 3-9 Replacing the Stops on the Foot Pedal Assembly Replacing the Pedal Potentiometer..... Removing the Video Display Replacing the Video Display. Removing the Game PCBs Replacing Static-Sensitive Devices Removing the Speakers Illustrated Parts Lists
Glossary Warranty Final Lap Upright
Final Lap Upright
List of Illustrations
Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4
Figure 2-1
Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5
Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-11 Figure 4-12
Table 1-1 Table 1-2
Table 3-1 Table 3-2 Connected Cabinets and Their Link PCBs. Car-Type Connectors Utility Panel Controls Other Game Control Locations
Self-Test Screen
Opened Control Panel Maintaining the Steering Wheel Assembly .. Maintaining the Foot Pedal Assembly . Repairing the Gear Shifter video Display Removal ..
Cabinet-Mounted Assemblies . Control Panel Assembly.... Steering Wheel Assembly Gear Shifter Assembl Foot Pedal Assembly Linear/Switching Power Supply Assembly .. Coin Acceptors, Inc. Coin Door Assembly . Final Lap CPU PCB Assembly Final Lap Video PCB Assembly. Final Lap Small ROM PCB Assembly Final Lap EMI PCB Assembly .. Final Lap Link PCB Assembly
List of Tables
Game Specifications . Car-Type Connectors.
Preventive-Maintenance Items Game Troubleshooting
Safety Summary
The following safety precautions apply to al! game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
Chapter 1
Set-Up
How to Use This Manual
This manual is written for game operators and service personnel, and provides information for setting up, playing, testing, and maintaining your Final Lap™ Upright game. The manual is divided into the following chapters: © Chapter 1 contains set-up and game play information. © Chapter 2 contains self-test procedures. ° Chapter 3 contains preventive maintenance and repair procedures. © Chapter 4 contains illustrated part lists. Wiring and schematic diagrams for the Final Lap Upright game circuitry are contained in the Schematic Package Supplement (SP-322) included with your game. This chapter includes information required to set up and play your Final Lap Upright game. Read this chapter carefully before you turn on the game.
Set-Up
This cabinet should be connected to a grounded threewire outlet only. If you have several cabinets, each one should be connected to its own separate grounded outlet. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded.
Inspecting the Game Please inspect your Final Lap Upright game carefully to ensure that the game is complete and was delivered to you in good condition. Figure 4-1 shows the locations of the parts of the game. Table 1-1 lists space, power, and environmental requirements. Inspect the game cabinet and seat assembly as follows:
- Examine the exterior of the cabinet for dents, chips, or broken parts.
- Unlock and open the lower service door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. (The connector bracket next to the EMI enclosure is for the car type selection. One of three connectors can be plugged into the connector bracket or none of them may be. For more information, see Choosing the Car Type in this chapter.) Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed edge connector can damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c, Inspect the power cord for any cuts or dents in
1-2 Final Lap Upright
the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), and speaker. Make sure that they are mounted securely and that the ground wires are connected.
Table 1-1 Game Specifications
Characteristic Specification
Power Consumption 150 V-A, 110 W RMS Temperature +5° to +50° C (437° to +122° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games) Width 49 in. (124.5 cm.) Depth 33 in. (84 cm.) Height 72 3/8 in. (184 cm.) Weight 450 Ibs. (204.5 kg.)
Installing the Attraction .
Sign
The attraction sign mounts on the top panel of the game. See Figure 4-1. Put the attraction sign on top of the game and center it. The front edge should be behind the retainers. Peel off the covering on the tape on the bottom of the sign and press the tape down on the cabinet.
Connecting Cabinets
You can connect up to four cabinets together. Each cabinet is shipped with a 6-foot-long connecting cable. If you are connecting three or four cabinets together, you will need longer cables, which are available from Atari Games Customer Service. These cables are 10 feet long (part no. 150031-120) and 20 feet long (part no. 150031-240).
- Turn off the game power to all the cabinets.
- Find the Link PCB in the back of the game. Plug in the connecting cables as shown in Figure 1-1. Each cable must be connected from an input to an output.
- Switch the connecting switch located on the Link PCB to the down position on all the cabinets that are linked together.
Final Lap Upright Set-Up
One Cabinet Two Cabinets
Four Cabinets
Connected Cabinets and Their Link PCBs
Choosing the Car Type
Each player can have one of four car types. These are selected by plugging in different connectors (included with the game) into the car-type connector bracket. The car-type connector bracket is next to the PCB enclosure and shown in Figure 1-4. At the factory, one car-type connector is plugged into the car-type connector bracket and the other two connectors are attached to it by a tie wrap. In Figure 1-2 the car-type connectors are shown with the wires at the different locations. The car types and colors with their corresponding connectors are shown in Table 1-2. McLaren Car Lotus Car (Red and White) (Yellow)
nH
Figure 1-2 Car-Type Connectors
1-3
Set-Up
Table 1-2 Car-Type Connectors
Car Type Color Connector
| March | Blue | Has wires at all 4 pins. |
| Mclaren | Red and white | Has wires at pins 2 and 4. |
| Williams | White, blue, | No connector. |
and yellow
| Lotus | Yeliow | Has wires at pins 1 and 3. |
Control and Switch : Locations
The controls and switches are located on the utility panel behind the upper coin door and on the back of the game.
Power On/Off Switch The power on/off switch is located at the bottom left of the cabinet. (See Figure 4-1.)
Volume Control The volume controls are located on the self-test utility panel behind the upper coin door. (See Figure 1-3.) Each player has two volume controls which adjust the level of sound from two speakers over each video display.
Self-Test Switch Each game has two self-test switches located on the utility panel behind the upper coin door. (See Figure 1-3.) The self-test switches are slide switches.
Left Player Right Player Left and Right
Left and Right Speaker Volume
Speaker Volume
Aux. Credit Switch
Right Player Right Player Self-Test
| Left Player | Coin | ae erent | switch |
Coin Counter Counter Left Player Self-Test ‘Switch
Figure 1-3 Utility Panel Controls Final Lap Upright
Each video display has its own self-test switch that selects the Self-Test Mode to check game operation. See Chapter 2 for a complete description of the self-test. Auxiliary Credit Switches Each game also has two auxiliary credit switches, next to the self-test switches on the utility panel. These are push button switches. Use either auxiliary credit switch to give a player coin credits. These switches do not activate the coin counter when they are used. This may be helpful if you need to troubleshoot the player start circuitry. Connection Switch The connection switch is on the Link PCB (see Figure 1-2). This switch should be in the down position with connecting cables plugged in, if you have two or more cabinets connected together. For more information, read Connecting Cabinets in this chapter.
Coin Counter The two coin counters, one for each player, are located on the utility panel inside the upper coin door. The coin counter records the number of coins deposited.
Car-Type
On/ott ‘Switch
Figure 1-4 Other Game Control Locations
Final Lap Upright
Setting the Coin and Game
Options
The Final Lap Upright coin and game options are set in the Self-Test Mode. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.
Game Play
This section of the manual describes the theme of the Final Lap Upright game and the game play features. Introduction Final Lap is the first linked game designed for the amusement industry. Originally created by Namco Limited of Japan, Final Lap Upright is a realistic racing game in the tradition of Pole Position. Each Final Lap Upright unit is actually two games in one, with two separate video displays linked together for interactive play. Realistic player controls consist of a steering wheel with return-to-center steering, a high/low shifter, and a gas pedal. As many as four Final Lap Upright units can be linked together for unprecedented competition: Up to eight players can compete head-to-head.
Play Mode Imagine yourself racing head-to-head against the player next to you. You see his car approaching in the rear-view mirror, and suddenly, he passes you on the inside, narrowly missing a road sign. You weave be- Set-Up
tween the other competitive cars in hot pursuit. You are on his tail through the hairpin and pass him in the straightaway! The status screen tells you that you are now in first position. You pass the finish line before the time runs out and again get extended time, but the question still remains: can you complete the final lap? To start the game, one or more players deposit coin(s) in the slot corresponding to their video display (e.g., the right player uses the right coin slot and the left player the left slot). The green light flashes, the green flag is waved and the race is on!
- To begin a head-to-head race, players must deposit coins within 16 seconds of each other.
- One player can compete against the clock or multiple players race can simultaneously on the same course.
- Each player has his own realistic first-person perspective of the track and sees his competitors’ cars on his screen. ¢ New players can start a new game even if another race is in progress. ¢ As an incentive for multiple-player games, all players can continue for an extended time, as long as at least one player completes the lap within the time allowed on the computer clock shown in the center of the video display.
- Players who set the best lap time are rewarded with a bottle of champagne in the winner's circle.
- Ifa player's time is fast enough, the player can enter his initials on the high score table.
1-5
Set-Up Final Lap Upright
N O T E S
Chapter 2
Self-Test
The Final Lap™ Upright game tests itself and provides visual and audible indications of the condition of the game circuitry and controls. Self-test information is displayed on the screen and through the sound system. No additional equipment is required. We suggest that you perform a self-test at least once a day and when you first set up the game, connect additional cabinets, collect coins, or when you suspect game failure. Use the self-test to check the game circuits, check the option settings, and change the option settings. The self-test switches (one for
each display) are located on the utility panel behind the upper coin door. The self-test switches are the slide switches on the bottom of the utility panel.
Self-Test
When you turn off the self-test switch, the game returns to the attract mode. When you turn on the selftest switch, the self-test screen appears. To move through the options and tests, press the gas pedal and change the gear shift from low to high. (You will hear a roar through the speakers when you change the gear shift.) The next option setting now flashes. To move to the next option or test, do the same procedure. You can only move down the screen. When you reach the end of the list, you return to the Sound test. To change a flashing option setting, move the gear shift from low to high. Do not press the gas pedal. Every time you move the gear shift, a new setting appears. Once you choose a new setting, you can return immediately to the attract mode, if you like.
RAM Test
This tests the game RAMs. If the game RAMs are working correctly, OK appears. If the screen shows anything besides OK, a qualified technician should check the game boards.
ROM Test
This tests the game ROMs. If the game ROMs are working correctly, OK appears. If the screen shows anything besides OK, a qualified technician should check the game boards.
Gas Pedal Test
GAS is the gas pedal test. Press the gas pedal, and the number to the right increases. Release the pedal, and the number decreases. If you are not pressing on the gas pedal, the number should be 00. If the number does not appear this way, then do the following:
RAM OK ROM OK GAS 00 BRAKE 00 STEERING 06 SOUND 00 SCl OK LINK ON 2 CARTYPE LOTUS MOTION OFF
COINT; 2COINS 1 CREDIT COIN2; 2COINS {| CREDIT RANK B ROUND 4
HISCORE INITIALIZED
Figure 2-1 Self-Test Screen
= Final Lap Upright
1, Check to make sure the gas pedal is returning to the top of its mechanical range. If it does not, repair or replace the gas pedal.
- Turn the self-test switch off and then on again.
- The number should reset to zero.
- If it does not, check the potentiometer on the gas pedal.
Brake Test
BRAKE does not apply to the Final Lap Upright game. It will show the same values as the gas test.
Steering Wheel Test
STEERING is the steering wheel test. When you turn the wheel to the left, the number increases. When you turn the wheel to the right, the number decreases. If you are not turning the steering wheel, the number should be 00 or FF. If the number does not appear this way, then do the following:
- Check to make sure the steering wheel returns to the center. If it does not, repair the steering wheel.
- Turn the self-test switch off and then on again.
- The number should reset to zero.
- If it does not, check the potentiometer on the steering wheel.
Sound Test
SOUND is the sound test. Cycle through the five sounds to test the audio circuitry. : Coin Options The COIN 1 option sets the coin option for each player. The COIN 2 setting does not apply to this game. You can choose 1 to 8 coins and 1 to 8 credits, The coin amounts and the credit amounts change independently of each other. The recommended option setting is 2 coins for 1 credit.
Difficulty Level RANK is the difficulty level of the game. When you change the rank, you shorten or lengthen the game time.
Final Lap Upright
The levels are:
- A (easy) © B (medium)—recommended setting,
- C chard)
- D (difficult)
Number of Laps ROUND is the number of laps each player is permitted to complete in each game. If one player completes a lap in less than the allotted time, then all players receive another lap.
These are the settings for the number of rounds:
¢ 4 (ecommended setting) au
Communication Circuit
Test
SCI, at the top right of the screen, indicates whether the Game PCB communications circuits are working correctly. SCI ON should be followed by four letters and numbers if the circuits are working correctly. If you see SCY NG, then a problem exists. Check the connecting cables to other games and the connectors.
Linked Games
LINK counts the number of game PCBs connected together (not the number of cabinets). LINK should al- Self-Test
ways read On. If it reads Off, the switch on the Link PCB is in the wrong position. Check Figure 1-1, Link PCBs on Connected Cabinets, for the correct position of your switch. If you have one cabinet, the number of linked games should be 2. If you have 3 cabinets connected, the link number should be 6. If you do not have the correct number of links, check the connections between your games.
Car Type
The CAR TYPE is the type and color of car that each player has. Each type of car has a different color. For more information about choosing the car type, see Choosing the Car Type in Chapter 1.
Motion Test
MOTION does not apply to the Final Lap Upright game. It should always read Off.
Test Pattern
When you tum off the self-test, you will briefly see a test pattern. Use this screen to check the convergence and the color balance of the video display. For more information, see your video display service manual.
Reset the High Score Table To reset the high score table, turn the steering wheel until the number 1F appears and change the gear shift to high. The words HISCORE INITIALIZED appear at the bottom of the self-test screen. The high score table now shows the default names and times.
Self-Test Final Lap Upright
N O T E S
Chapter 3
Maintenance
This chapter includes preventive maintenance and repair procedures for the Final Lap™ Upright game components that have the most use. To assure maximum trouble-free operation from this game, you should perform preventive maintenance described in this chapter. Removal, disassembly, reassembly-assembly, and replacement procedures are provided for components that might need to be repaired. If a game part is mentioned, but not illustrated, refer to Chapter 4, Illustrated Parts Lists, for information.
es PR i
Maintenance Final Lap Upright
Preventive Maintenance
Preventive maintenance includes cleaning, lubricating, and tightening hardware. Preventive maintenance should be performed regularly, so the game stays in top condition and major problems are avoided. Preventive maintenance tasks and intervals are shown in Table 3-1. More information about performing each task follows the table.
Maintaining Your Game
For the best performance from your Final Lap game, you should check and maintain your game according to the times and tasks shown in Table 3-1. How to check and maintain these items is explained further in this section. You may want to perform these tasks more often if the game is heavily used.
Opening the Control Panel
1, Remove the four tamperproof screws and washers in the front of the control panel.
- Open the control panel. See Figure 3-1.
Maintaining the Steering Wheel Assembly
This section explains how to maintain the steering wheel assembly on your Final Lap Upright game. For repair and replacement procedures, see Repairs.
Tightening the Screws on the Stop Brackets
- When the contro! panel is open, the two stop brackets on the steering assembly face out. See Figure 3-2.
- Make sure the four cross-recessed screws are tight. They should be torqued to 28 inch-pounds.
- If a screw has fallen out, replace it immediately.
Tightening the Socket-Head Screw on the End of the Steering Shaft
- Open the control panel.
- Use a 3/16-inch Allen head wrench to tighten the screw on the end of the steering shaft. See Figure 3-2. Make sure it is torqued to 95 inch-pounds.
Tightening the Screws on the Spring Catch The stop catch is mounted directly on the steering shaft, over the spring. The screws secure the spring
Table 3-1 Preventive Maintenance Items Part When to Check What to Check and Maintain
| Steering Wheel | Every 3 months | Does the steering wheel return to center? If it does not, repair it immediately. |
Turn the sieering wheel as far as you can. Does it hit metal? Replace the O-rings on the stop. Open the control panel. Check the catches on the ends of the spring. Are they bent or broken? If so, replace the spring. Open the control panel and tighten these screws on the steering wheel: 4 cross-recessed screws on the stop brackets Screw on the end of the steering shaft 2 socket-head screws on the spring catch. Every 6 months Lubricate the spring with Nyogel grease. Lubricate the bronze bearing on the case with light oil.
| Gear Shift | Every 3 months | Check the gear shift for wear. If a rubber stop is wearing, turn the stop. |
Lubricate the shifter plate.
| Pedal | Every 6 months | Check the springs to make sure they are not sprung and are returning the |
pedal to the top position. Replace if necessary. Lubricate the pin in the pedal link with lithium grease. Check the front and back rubber stops for wear.
| Coin Mechanism | Every 3 months | Clean. |
Interior Components Every 6 months Clean.
Final Lap Upright
catch, which keeps the spring in tension. See Figure 3-2.
- Open the control panel.
- Turn the steering wheel so you can reach both the socket-head screws and the nuts on the spring catch.
- Use a 5/64-inch Allen head wrench for socket-head screws and an 11/32-inch hex driver for nuts, and torque the screws to 28 inch-pounds.
Lubricating the Spring
- Open the control panel.
- The spring is inside the steering wheel housing. Lubricate the spring with Nyogel grease.
Lubricating the Bearing To lubricate the steering assembly bearing you must take off the screw on the end of the steering wheel shaft, the gear on the shaft, the retaining ring, and the washer.
- Take off the gear on the steering wheel shaft by removing the socket-head screw on the end of the shaft. See Figure 3-2.
- Pry off the retaining ring. Cover the ring with a cloth while you pry it, so it doesn’t fly off.
- Take off the washer. Maintenance
4, Put two drops of light oil on the top surface and inner surface of the bronze bearing.
- Reassemble the steering wheel shaft.
Lubricating the Gear Shift Assembly
Maintaining the Pedal Assembly
- Open the control panel.
- Grease the shifter plate with lithium grease. See Figure 3-4.
- Check the round rubber bumpers for wear. If a bumper is worn, turn it.
To maintain the pedal, grease the pin in the pedal link and check the springs and stops for wear. Push the pedal down a few times to make sure it returns easily to the top position. If it does not return easily, probably the pin in the pedal link needs to be lubricated. If the pin is lubricated, check the springs at the rear of the pedal to make sure they are not sprung.
While you are looking at the pedal, also check the front and rear rubber stops for wear.
Steering Whee! Gear Shift
Assy Assy
‘Tamperproot ‘Screw and Washer
Figure 3-1 Opened Control Panel
3-3
Maintenance
Lubricating the Pin
- Turn off the power to the game.
- Disconnect the pedal wiring harness from the main harness.
- Remove the four nuts that hold the pedal in the game, Use a 7/16-inch wrench. 4, Take the pedal out of the game.
- On the left side of the pedal assembly at the bottom is a hole for lubricating the pin and the slot. Put lithium grease on the pin and in the slot. Push the pedal up and down to work the grease around to lubricate the slot.
Socket-Head Screw
‘Shaft Washer
Bronze Bearing
Hex Nut
Catch
Right Stop Bracket Final Lap Upright
- Reinstall the pedal in the game and reconnect the harness.
Cleaning the Coin
Mechanism
Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air,
24 Tooth Spur Gear
36 Tooth Spur Gear
Retaining Ring
Potentiometer
Nyogel Grease Torsion Spring
Lock Nut Washer Steering Whee! © s O-Ring Holder and Stop
Steering Wheel Cap
Figure 3-2 Maintaining the Steering Wheel Assembly
3-4
Final Lap Upright Maintenance
HT 2. Discharge the high voltage from the cathode-ray Cleaning the Interior tube (CRT) before proceeding. The display assem- Components bly contains a areal for discharging the high volt- A age to ground when power is removed. However, Perform the following procedure to clean the compo- to make certain, always discharge the display as nents inside the cabinet. follows:
- Open the rear access panel and display service a. Attach one end of a solid gauge wire to a well- Panel. insulated screwdriver or wooden handle.
b. Attach the other end of the wire to an earth
1/2-Inch Retaining Ring
Harness:
1/4-Inch Retaining Ring Link
Link Long Stop Shaft Bracket Long Rubber Stop 1/4-Inch Retaining Ring Bearing (4 Places) Link Pin
+#8-32 Screw / Spring (2 Places) p a otentiometer Seow Briltps Phillips a a ‘Screw Split Lock Bracket Spit Lock Washer Washer
Figure 3-3 Maintaining the Pedal Assembly
Maintenance
to remove loose dirt-and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supplies, PCB assemblies, display, etc.).
3-6
Final Lap Upright Maintenance
Repairs
Repairs include the removal, disassembly, reassembly- 1. Open the control panel. assembly, and replacement of game components. The 2. Remove the steering wheel following procedures are provided for components : . that may require repairs. a. Pry off the center steering wheel cover. Use Table 3-2 to find the solution to problems you b. Remove the three hex-head screws underneath may be having with your Final Lap Upright game. the cover that hold the steering wheel on the steering wheel assembly. Take off the steering Replacing the O-Rings on wheel.
- Take off the nuts that hold the plastic dashboard in the Steering Wheel Stop place. Use a 7/16-inch wrench. If the steering wheel hits metal when it turns, the The stop is located on the front of the steering wheel O-rings on the steering wheel stop must be replaced. assembly and is held on by a nut inside the steering See Figure 3-2.
Table 3-2 Game Troubleshooting
Problem Solution
Steering Wheel Hits metal when it turns Replace O-rings on the stop. Spins freely Replace stop and spring. Does not return to center, but does Replace spring. not spin freely Fails the self-test Check mechanical parts, then replace potentiometer. Steering wheel is broken, but internal Replace steering wheel. mechanism is undamaged. Shifter No response from screen; no change in Replace the microswitch if other parts are in good condition. volume when shifter is moved Pedal Sticks Grease pin on pedal link (described in Preventive Maintenance). Does not return First grease pin, then check springs. Replace springs if necessary. Fails the self-test Check mechanical parts, then replace potentiometer. At top or bottom of the movement, Replace rubber stops. the pedal hits metal. Video Display Any problem Refer to video display service manual. Speaker No sound Make sure volume is turned up for each speaker. If the volume is turned up, do the following: Do the self-test. Check the wiring and the volume control potentiometer. Replace the defective speaker. Non-Mechanical Problems Players cannot race together. Check the switch on the link PCB to make sure it is in the right position. (This is described in Chapter 1.) Players have the same color of cars. With one or two cabinets linked, each player can have an individual color. ‘With more that two cabinets linked, some players will have the same color cars. For more information, see Chapter 1, Choosing the Car Type. Players do not receive the same number Check that the ROUND setting in the self-test is the same for all players. of laps, even though they are racing together.
3-7
Maintenance
wheel assembly housing. Two O-rings are mounted on the stop. If one is broken or worn, replace both.
- Slide the old O-rings off and slide the new O-rings on. Make sure the O-rings fit properly in the grooves on the stop.
- Install the plastic dashboard.
- Install the steering wheel. Install the three screws and tighten them to 95 inch-pounds.
- Close the control panel.
If the Steering Wheel Does
Not Return to the Center If the steering wheel does not snap back to the center when you turn it, you may need to replace the stop and the spring. See Figure 3-2. Replace the stop and the spring if you can spin the steering wheel in a complete circle. Replace the spring if the steering wheel does not return to the center, but does not spin in a complete circle.
Replacing the Spring on the
Replacing the Stop on the Steering Wheel Assembly
. Open the control panel.
- Loosen the screw on the end of the steering shaft. Take off small gear at the end of the steering shaft.
- Pry off the retaining ring. Be careful when you pry it off, since it will fly off the shaft. 4, Remove the large washer below the retaining ring.
- Take off both stop brackets by removing the crossrecessed screws holding the brackets on the case.
- Take off the catch on the spring. Use 9/64-inch Allen wrench on the socket-head screws and an 11/32-inch hex driver on the Nyloc nuts. Remove the screws, nuts, spacers, and catch.
- Pull the shaft out a small amount towards the steering wheel and remove the spring.
- Grease the shaft with Nyogel, if necessary, Put on a new spring. The spring must be well lubricated with Nyogel grease.
- Replace the washer and retaining ring. Se . Replace the catch. Make sure it holds the spring in tension.
- Replace the gear and the socket-head screw on the end of the shaft. The steering shaft gear must mesh with the gear on the potentiometer shaft and must be the same height. If not, move the gear on the potentiometer shaft.
3-8 Final Lap Upright
- If you move the gear on the potentiometer shaft: a. Make sure the flat part of the potentiometer shaft lines up with the center terminal on the potentiometer. b. Now put the gear on the potentiometer. Make sure it completely meshes with the gear on the steering shaft and is the same height as the other gear. c. Check to be sure the potentiometer gear set screw is on flat part of potentiometer shaft and lines up with the center terminal on the potentiometer. Tighten the set screw.
- When the gears mesh and are the same height, tighten the set screw on the gear on the potentiometer shaft.
- Reassemble the steering shaft. If you do not need to replace the stop, close the control panel and install the tamperproof screws.
- Open the control panel. 2, Remove the steering wheel. a. Pry off the center steering wheel cover. b. Remove the three hex-head screws underneath the cover that hold the steering wheel on the steering wheel assembly. Take off the steering wheel.
- Take off the nuts that hold the plastic steering wheel cover in place. Use a 7/16-inch wrench. The stop is located on the front of the steering wheel assembly and is held on by a nut inside the steering wheel assembly housing. See Figure 3-3. If the steering wheel can be turned in a complete circle, then the stop is probably sheared off in front. 4, Remove the nut that holds the stop on the inside of the steering wheel assembly. Use a 3/8-inch flat wrench. Insert the wrench through the back of the housing to get the nut off.
- Put on a new stop. Tighten the nut to 47 inchpounds.
- Make sure the two O-rings are securely in the grooves.
- Install the plastic dashboard.
- Install the steering wheel. Put a drop of glue on each of the three screws before you install them, and then tighten the screws to 95 inch-pounds.
- Close the control panel.
Final Lap Upright
Replacing the Steering
Wheel Potentiometer
If the steering wheel spring and the stop are good, but the player's car on the video display is not responding, check to see if the steering wheel fails the self-test. If it fails, you may need to replace the potentiometer.
- Open the control panel. See Figure 3-2.
- Take off large gear on the potentiometer shaft. Use a 5/64-inch Allen head wrench to loosen the gear set screw.
- Use a 1/2-inch hex driver to remove the lock nut and washer that hold the potentiometer on the case.
- Push the potentiometer out towards steering wheel. Remove the wiring harness.
- Replace the potentiometer. Put the key into the hole in the case.
- Make sure flat part of the potentiometer shaft lines up with the center terminal on the potentiometer.
- Tighten the potentiometer lock nut to 30 inchpounds,
- Now put on the gear on the potentiometer. Make sure it completely meshes with the gear on the steering shaft and is the same height as the other gear.
- Check to be sure the potentiometer gear set screw is on flat part of potentiometer shaft and lines up with the center terminal on the potentiometer. Tighten the set screw.
- Install the wiring harness. The red wire is on the left, the brown wire is in the middle, and the black wire is on the right.
Wheel
If you want to replace the steering wheel, but not the inside controls, follow this: procedure. You do not need to open the control panel.
- Pry the center cover off of the steering wheel.
- Use a 1/4-inch Allen wrench to remove the three screws in the center of the wheel.
- Remove the steering wheel. 4, Install the new steering wheel. Install the screws and torque each one to 95 inch-pounds.
- Replace the center cover. Maintenance
Replacing the Gear Shift
Assembly
. Open the control panel.
- Disconnect the wiring harness from the microswitch,
- With a 3/8-inch nut driver, remove the four nuts holding the gear shift on the panel.
- Remove the gear shift through the front of the control panel.
- Replace the gear shift. Assemble in reverse order.
Replacing the Microswitch = the Gear Shift Assembly . Open the control panel.
- Disconnect the wires to the switch on the gear shift. See Figure 3-4.
- Remove the screws that hold the switch on the gear shift. 4, Remove the switch.
- Replace in reverse order.
Microswitch Rubber Bumper
Shifter Plate
Figure 3-4 Repairing the Gear Shift
Replacing the Stops on the Foot Pedal Assembly If the pedal has worn through the rubber stops on the back or the front, you should replace the stops.
3-9
Maintenance
- Turn off the power to the game.
- Disconnect the pedal wiring harness from the main harness. 3, Remove the four nuts that hold the pedal in the game. Use a 7/16-inch wrench. 4, Take the pedal out of the game.
Replacing the Front Stop
Remove the retaining rings from the stop shaft. Now remove the shaft from the frame. See Figure 3-3.
- Take off the old rubber stop. Slide on the new stop.
- Reinstall the shaft in the frame and put on the retaining rings.
- Put the pedal back into the game, put on the nuts, and reconnect the harness.
Replacing the Back Stop
- Take the springs off the frame. See Figure 3-3.
- Remove the cross-recessed screws on the bottom of the pedal that hold the stop bracket on the frame. Remove the stop bracket.
- Remove the retaining rings from both ends of the stop shaft. Now remove the shaft from the bracket.
- Take off the old rubber stop. Slide on the new stop.
- Put the shaft back in the bracket. If you bend the bracket taking the shaft out or putting it in, be sure to bend it back before you reinstall it.
- Install the stop bracket in the frame. Reconnect the springs.
- Put the pedal back into the game, put on the nuts, and reconnect the harness.
Replacing the Pedal
Potentiometer
If the pedal fails the self-test, you may need to replace the potentiometer. However, first make sure that the link and the pin are functioning properly. See Figure 3-3.
- Take the pedal assembly out of the game.
- Remove the wiring harness from the potentiometer.
- Take the bracket with the potentiometer on it out of the pedal frame by removing the two cross-recessed screws in the bottom of the frame. 4, Take the pedal link off the potentiometer shaft by loosening the lock nut holding the link on the
3-10 Final Lap Upright
shaft. Take off the nut and washer and remove the potentiometer.
- Put on the new potentiometer. Make sure you insert the potentiometer key into the hole at the top of the bracket.
- Put on the washer and lock nut. Tighten the lock nut on the potentiometer.
- Install the pedal link the potentiometer shaft. Be sure to tighten the lock nut on the flat part of the shaft.
- Reconneci the wiring assembly to the potentiometer. The wires to the potentiometer are red on the top, white in the middle, and black on the bottom.
- Install the bracket back in the pedal frame.
- Replace the pedal assembly in the game. Connect the pedal wiring harness to the main wiring harness. Ss
Removing the Video Display
Perform the following procedure to remove the video display. (See Figure 3-5.)
- Turn the game power off and wait two minutes. Leave the power cord plugged in.
- Remove the top access panel and the small access panel.
- Discharge the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, al-
Final Lap Upright
Wooden
Replacing the Video Display
Speaker Panel
Grille Video
Figure 3-5 Video Display Removal
ways discharge the display as follows: a. Attach one end of a solid 18-gauge wire to a well-insulated screwdriver or wooden handle. b. Attach the other end of the wire to an earth ground. c. Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait two minutes and repeat part c. . Disconnect the display harness connectors from the display. . Remove the four tamperproof screws in the control panel and open the control panel. |. Use a screwdriver to pry up the bottom edge of the display shield. Remove the display shield. . Take-out the bezel. . Remove the wooden display panel which is held on the cabinet with six cross-recessed screws. . Use a 3/8-inch nut driver to remove the four hex head screws holding the video display mounting brackets on the cabinet shelf. Maintenance
Attraction Shield Hex-Head Screw and Washer
Shield
- Pull the display forward and carefully lift the display out.
- Replace the video display as described in the following procedure.
Perform the following procedure to replace the video display in the cabinet. (See Figure 3-5.) 1, Carefully lift the video display onto the display shelf in the cabinet.
Maintenance
- Position the display so that the four holes in the video display mounting brackets line up with the four holes in the video display shelf.
- Loosely install the four hex-head screws through the mounting brackets and into the video display shelf. 4, Install the wooden display panel the with six crossrecessed screws.
- Install the bezel.
- Install the video display shield by resting it on the lip above the control panel.
- Close the control panel and screw in the four tamperproof screws,
- With the hex-head screws loosely installed, push the video display forward to meet the bezel.
- Use a 3/8-inch nut driver to tighten the bolts, Be sure that the display is centered horizontally.
- Connect the display harnesses to the display. 11, Replace the access panels.
Removing the Game PCBs
Perform the following procedure to remove or replace the Final Lap Video, CPU or EMI PCBs.
- Tum the game power off.
- Open and remove the service panel.
- The vertical green PC board is the EMI board. It is connected to the CPU PCB and the video PCB inside the EMI enclosure. The EMI enclosure is the perforated metal box. See Figure 1-4. 4, Remove the six screws that hold the EMI PC board on the enclosure.
- Take off the edge connectors on the EMI PC board.
- Carefully pull the EMI PC board out, along with the CPU and the video PCBs.
- Replace the Game PCBs in the reverse order of removal.
3-12 Final Lap Upright
Replacing Static-Sensitive
Devices
Be careful when you are working with static-sensitive devices on the game PCBs. These can be microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge that has built up in your body can cause a Static-sensitive device to fail. Leakage from an improperly grounded soldering iron can also cause a static-sensitive device to fail. Before you handle a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. When you solder a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. Before you replace a static-sensitive device, make sure it is actually defective. A static-sensitive device can appear defective due to leakage on a PCB. To make sure a device is defective, ground any static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. If you are replacing a static sensitive device, new static-sensitive devices may be packaged in conductive foam or may have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.
Removing the Speakers
Perform the following procedure to remove the speakers. See Figure 4-1 for the location of the speakers.
- Turn the game power off.
- Remove the speaker grille and remove the screws that hold the speaker in place.
Chapter 4
Ihustrated Parts Lists
This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers, and so on usually are not listed in the parts lists. The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All Aprefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (000598- through 201000-). Ending the list are part numbers with a two-number designation followed by a hyphen (00- through 99-). The PCB parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. task re Atari Games Customer Service " we phone numbers are listed on the oe 7 inside front cover of this manual.
Final Lap Upright Illustrated Parts Lists
72-5120 #10-24 Hex Head Screw 75-0408 046010-01 Lower Retainer , i #10 Split-Lock Washer 78-6900402 1/4-Inch Foam Tape 75-0308
170003-004 Fluorescent Lamp
171086-005 Lamp Fixture
(Figure 4-2) 045515-01 Speaker Grille 78-6901 1/4-Inch Foam Tape
046012-01 A045870-01 Left Decal ‘Steering Wheel Assy (Figure 4-3) 038091-01 Coin Box
171027-001 Coin Door 176037-4016 Tamper Proof Screw 4046215-01 Foot Pedal Assy (Figure 45) 75-0702 1 1/4-Inch Flat Washer ‘75-045S 41/4 Split-Lock Washer 75-9158 1/4-20 Hex Nut ‘75-010F #10 Washer
Figure 4-1 Cabinet-Mounted Assemblies, Front View A046000-01 D
4-2 #10 Washer
Shield
Final Lap Upright Iustrated Parts Lists
oaso42-01 rep Access 046047-01 Panel LA ‘Attraction Sign
03733201 Grille
\tems Not Shown
‘A043908-01 +5v Harness Assy
‘A045509-01 Jumper Select ‘Assy
046029-01 Display Access Panel
046046-01 Coinage Label
A046231-01 i Main Harness A046238-01 a Utility Panel (A046232-01 Assy Power Harness Assy
| EMI Enclosure | ‘A0A5E20-01 | A046233-01 | |
| 185027-001 | ‘On/Off | lad Supply | ‘Speaker |
| EMI PCB | Harness Assy | Figure 4-6) | Hamess Assy |
(Figure 4-11) « '99-090360 046012-02
| CPU PCB | 78-3201 | Right Decal |
(Figure 4-8) Glide 1-072 99-090361 bari Video PCB Sfeet Cebie i sakete 178126-002 99-09 Tam yf ‘Small ROM PCB Key Dever (Figure 4-10)
Figure 4-1 Cabinet-Mounted Assemblies, Rear View A046000-01 D
Illustrated Parts Lists Final Lap Upright
Cabinet-Mounted Assemblies , Parts List
Part No. Description A043909-01 +5v Harness Assembly A045846-01 Coin Door Label A045862-01 EMI Enclosure Assembly A045909-04 Jumper Select Assembly A045920-01 Power Supply Assembly (See Figure 4-6) A046004-01 Control Panel Assembly (See Figure 4-2) A046215-01 Foot Pedal Assembly (See Figure 4-5) A046231-01 Main Harness Assembly A046232-01 Power Hainess Assembly A046233-01 Speaker Harness Assembly A046236-01 On/Off Harness Assembly A046238-01 Utility Panel Assembly 037332-01 Louvered Grille 038091-01 Molded Coin Box 045515-01 Speaker Grille 045846-01 Coin Door Label 045852-01 Link PCB Bracket 045868-01 Car-Type Selection Connector Bracket 045937-01 Display Bezel 046007-01 Attraction Shield 046008-01 Attraction Decal 046009-01 Upper Retainer 046010-01 Lower Retainer 046011-01 Silkscreened Video Display Shield 046012-01 Left Decal 046012-02 Right Decal 046029-01 Display Access Panel 046035-01 Service Door 046036-01 Small Access Panel 046042-01 Top Access Panel 046043-01 Front Decal 046046-01 Coinage Decal 046047-01 Attraction Sign 139017-204 19-Inch Wells-Gardner Video Display 148007-104 Speaker 150031-072 6-Foot Connecting Cable with Phono Plugs 150031-120 10-Foot Connecting Cable with Phono Plugs (Not included with game; order separately.) 150031-240 20 Foot Connecting Cable with Phono Plugs (Not included with game; ordesseparately.) 155027-001 EMI PCB (See Figure 4-11) 155028-001 Link PCB (See Figure 4-12) 170003-004 36-Inch, 30W Cool White Fluorescent Lamp 171027-001 Over/Under 25¢/25¢ USA Coin Door (See Figure 4-7) 171086-005 36-Inch Fluorescent Lamp Fixture 176037-4016 Tamper Proof Black Screw 178023-001 4-Inch Swivel Caster 178056-002 Double-Sided 1/2-Inch Wide Foam Tape 178126-002 Tamperproof Hex Key Driver
4-4
Final Lap Upright Illustrated Parts Lists
Cabinet-Mounted Assemblies Parts List
Part No. Description 178232-001 Lamp Retainer Clip 72-5120 #10-24 Hex Head Screw 72-5516 1/4-20 Hex Head Screw 75-010F #10 Black Washer
75-0308 #10 Flat Washer 75-0408 #10 Split-Lock Washer 75-0458 1/4 Split-Lock Washer 75-07002 1 1/4-Inch Diameter Flat Washer 75-9158, 1/4-20 Hex Nut 78-3201 Adjustable Glide 78-6900402 1/4-Inch Wide Foam Tape 99-090360 Final Lap CPU PCB (See Figure 4-8) 99-090361 Final Lap Video PCB (See Figure 4-9) 99-090452 Final Lap Piggyback PCB (See Figure 4-10)
These are the technical supplements to the Final Lap Upright game: SP-322 Schematic Package ST-322 Self-Test Label TM-296 19-inch Wells-Gardner Video Display (#19K7901) Service Manual TM-325 Upright Final Lap Operator’s Manual
4-5
Mlustrated Parts Lists Final Lap Upright
Item Not Shown 046006-01 177010-240 Decal #10-24 Locknut 7010-244 75-0108 14-20 Locknut A045870-01 #10 Washer 75-0158 Steering 171088-001 1/4 Washer Wheel Assy Gear Shift Assy
75-0158 1/4 Washer
82-8512B Tamper Proot Screw
75-5512B 114-20 Carriage Bolt
7551128 ~176037-4016 78-6900402 #10-24. Tamperproof Foam Tape i Screw Carriage Bolt Teor 046005-01 Washer Control Panel Figure 4-2 Control Panel Assembly A046004-01 A
Control Panel Assembly Parts List
Part No. Description A045870-01 Steering Wheel Assembly 044751-01 Formed Plastic Dashboard 046005-01 Control Panel 046006-01 Control Panel Decal 171088-001 Gear Shift Assy 177010-240 #10-24 Polymer Locknut 7010-244 1/4-20 Polymer Locknut 75-0108 #10 Flat Washer 75-0158 1/4 Flat Washer 75-5112B #10-24 Black Carriage Bolt 75-5512B 1/4-20 Black Carriage Bolt 82-8512B Tamperproof Screw
Final Lap Upright Illustrated Parts Lists
N O T E S
Illustrated Parts Lists
4-8 Final Lap Upright
Items Not Shown ‘4045907-01 Guinn ‘Steering Wheel Wa oh Harness Assy fasher 106007-001 75-0155 72-8512 Penetrating 1/4 Flat Washer Socket Head Adhesive Screw 107013-001 17B101-018 Light Oil ight 4178012-007 24 Tooth Spur Gear Retaining Ring
178101-008 175002-001 36 Tooth Spur Gear Shaft Washer 17602-3804
#8-82 Lock 0488 Screw 72-8820 catch Socket Head Screw PP 045875-01 Left Stop Bracket anc Potentiometer
045871-01 3 L Housing
045872-01 Shaft 72-1806S #8-32 Phillips Screw 177010-238 045874-01 Hex Nut Torsion Spring
178027-001 Nyogel Lubricant
045934-01 Right Stop Bracket 178181-7804 178099-004 Steering Wheel es aheacid #10-32 Lock Nut 75-0108 #10 Flat Washer y
178245-001 Steering Whee! Cap 178223-006 O-Ring 72-8010 —_ ¥10-32 Socket Head Screw
Figure 4-3 Steering Wheel Assembly A045870-01 F
Final Lap Upright Illustrated Parts Lists
Steering Wheel Assembly Parts List
Part No. Description A045907-01 Steering Wheel Harness Assembly 045871-01 Housing 045872-01 Shaft 045873-01 Catch 045874-01 Torsion Spring 045875-01 Left Stop Bracket 045934-01 Right Stop Bracket 045955-01 O-Ring Stop 106007-001 Penetrating Adhesive 107013-001 Light Oil 175002-001 .750-Inch Diameter Shaft Washer 176022-3804 #8-32 x 1/4-Inch Socket Head Lock Screw 177010-238, #8-32 Nyloc Hex Nut 177010-241 #10-32 Nyloc Hex Nut 178012-001 .750-Inch Diameter Retaining Ring 178027-001 Nyogel Lubricant 178099-004 Steering Wheel 178101-008 36-Tooth Spur Gear with Hub 178181-7804 Steel Spacer 178223-006 O-Ring 178245-001 Steering Wheel Cap 178101-014 24-Tooth Spur Gear (Acceptable replacement is part no. 178101-007, spur gear with hub, with part no, 72-8518 (1/4-20 x 1.12:inch socket head screw) replacing part no. 75-8512 @1/4-20 x .75-inch socket head screw).) 119008-1001 5K Ohm Potentiometer 72-8512 #1/4-20 Socket Head Screw 72-1806s #8-32 Cross-Recessed Screw 72-8010 #10-32 Socket Head Screw 72-8510 #1/4-20 Socket Head Screw 72-8820 #8-32 Socket Head Screw 75-010s #10 Flat Washer 75-0158, 1/4 Flat Washer 75-0458 1/4 Flat Washer
Illustrated Parts Lists Final Lap Upright
99-215003
99-215004 ber 99-215001 Rubber Stop Handle and Shaft
99-218002 “Low/High* Cover Plate
Figure 4-4 Gear Shift Assembly A045870-01 E
Gear Shift Assembly Parts List
Part No. Description 99-215001 Handle and Shait 99-215002 “Low/High” Cover Plate 99-215003 Microswitch 99-2.15004 Rubber Stop
4-10
Final Lap Upright Illustrated Parts Lists
178012-006 1/2-Inch Rotaining Ring NOTE Be sure harmess wires are 14 S bie en A046234-01 clear of the moving parts. 043828-01 Gas Pedal 043831-01 Pedal Shaft / nia Harness Assy 046213-01 Frame 043832-02 ‘Short Stop Shaft 043835-02 Short Rubber Stop
178012-002 043830-01 1/4-inch Link 04383201 Retaining Ring / Long Stop Shaft 107027-001 043835-01 Lithium Gr Long Rubber Stop eee ium Grease 17801 2-002 1/4-Inch Retaining Ring 76-080802B Ne, ® Bearing < (4Places) Sa.
i> } “I 043691-01" ‘Spring (2 Places) 19-2026 Raieced Potentiometer eins ing Sleeve i Philip Sere bend 043834-01 Phillips Screw 75-0486 Stop Bracket 75-0486 Spit Lock Split Lock Washer Washer
Figure 4-5 Foot Pedal Assembly A046215-01A.
Foot Pedal Assembly Parts List
| Part No. | Description | Part No. | Description |
| 4046234-01 | Gas Pedal Harness Assembly | 046213-01 | Frame |
| 043691-01 | Spring | 046214-01 | Pedal |
| 043828-01 | Pedal Shaft | 107027-001 | Lithium Grease |
| 043829-01 | Pedal Bracket | 178012-002 | 1/4-Inch Diameter Retaining Ring |
| 043830-01 | Link | 178012-006 | 1/2-Inch Diameter Retaining Ring |
| 043831-01 | Pedal Tread | 19-9026 | 5K Ohm Potentiometer |
| 043832-01 | Long Stop Shaft | 72-1806F | #8-32 Phillips Screw |
| 043832-02 | Short Stop Shaft | 72-8808 | #8-32 Hex Socket Head Screw |
| 043833-01 | Spring Sleeve | 75-048C | #8 Split Lock Washer |
| 043834-01 | Stop Bracket | 75-9185 | #8-32 Hex Nut |
| 043835-01 | Long Rubber Stop | 76-080802B | 1/2-inch LD, Nyliner Bearing |
043835-02 Short Rubber Stop
4-11
Mlustrated Parts Lists Final Lap Upright
A043367-08 412-Inch Black Jumper cassee-o1 Assy 396-0: 479231-002 \ leetred ed Power Supply Base 149008-001 2-Position Terminal Block Leiabal bie dumper bio § SuraV Swtehing
Z
A42384-01 FFI Filter Assy
46-2013002 3A, 250 V, Slow-Blow Fuse
y, 179225-2201 1-Position Fuse Block ° °
° A049967-01 3-Inch Black Jumper ail A044337-01 O38544-01 auf Transformer Fuse Block Cover
Figure 4-6 Switching/Linear Power Supply Assembly A045920-01 A
4-12
Final Lap Upright Ilustrated Parts Lists
Switching/Linear Power Supply Assembly it Parts Lis'
Part No. Description A042384-01 RFI Filter Assembly A043367-01 3-Inch Black Jumper Assembly A043367-08 12-Inch Black Jumper Assembly A043367-09 12-inch White Jumper Assembly 034544-01 Fuse Biock Cover 043396-01 Power Supply Base 142045-001 120 VAC Isolation Transformer 149008-001 Hitron 5V/12V Switching Power Supply Assembly—see below 179225-2201 1-Position Fuse Block 179231-002 2-Position Terminal Block 146008-2022 3 A, 250 V, Slow-Blow Fuse
Hitron 5V/12V Power Supply Sub-Assembly Parts List
Part No. Description ‘itors 99-211036 Capacitor, Metal Film, 0.047 pf, 250V 99-211037 Capacitor, Metal Filrn, 0.22 uf, 100V 99-211038 Capacitor, Metal Film, 0.1 uf, 400V 99-211039 Capacitor, Metal Film, 0.022 pf, 100V 99-211040 Capacitor, Ceramic, 1800pf, 2 KV, Z5V 99-211041 Capacitor, Ceramic, 0.0luf, 1 KV, Z5U 99-211042 Capacitor, Ceramic, 0.001 uf, 2 KV 99-211043 Capacitor, Ceramic, 470 Pf, 1KV, Z5P 99-211046 Capacitor, Electrolytic, 100 uf, 200V 99-211047 Capacitor, Electrolytic, 1000 uf, 25V 99-211079 Capacitor, DE7100F22M 99-211080 Capacitor, 1000 pif, 35V 99-211081 Capacitor, 470 pf, 25V 99-211082, Capacitor, 220 pf, 16V Diodes 99-211005 Diode, Schottky, S10SC4M 99-211007 Diode, Zener, 1N752A. 99-211008 Diode, Rectifier, 1N4006 99-211009 Diode, Fast Recovery, RPG10B 99-211010 Diode, Fast Recovery, RPG10K 99-211011 Diode, Fast Recovery, RPG15SB 99-211012 Diode, Switching, 1N4148 99-211076 Diode, 31DQ04 Inductors 99-211084 Inductor, 8 wth
4-13
Illustrated Parts Lists
Hitron 5V/12V Power Supply Sub-Assembly Parts List, Continued Final Lap Upright
Part No. Description
99-211085 Inductor, 9.8 ph 99-211086 Inductor, 0.75 mh 99-211087 Inductor, 2.2 ph 99-211088 Inductor, 60 mh Resistors 99-211014 Potentiometer, Trimming, 3K Ohm. 99-211016 Resistor, Wire Wound, 150 Ohm, +5%, 2W 99-211017 Resistor, Wire Wound, 33 Ohm, +5%, 2W 99-211018 Resistor, Wire Wound, 0.47 Ohm, +5%, 2W
99-211019 Resistor, Wire Wound, 120 Ohm, +5%, 2W 99-211020 Thermistor, 0.5 Ohm, +5%, 5W 99-211021 Resistor, 2.2K Ohm, +2%, 1/4W 99-211023 Resistor, Carbon Film, 270 Ohm, +5%, 1/2W
99-211024 Resistor, Carbon Film, 470 Ohm, +5%, 1/4W 99-211025 Resistor, Carbon Film, 47 Ohm, +5%, 1/4W 99-211026 Resistor, Carbon Film, 330 Ohm, +5%, 1/4W 99-211027 Resistor, Carbon Film, 5.6 Ohm, +5%, 1/4W
99-211028 Resistor, Carbon Film, 8.2 Ohm, +5%, 1/4W 99-211029 Resistor, Carbon Film, 10 Ohm, +5%, 1/4W 99-211030 Resistor, Carbon Film, 39 Ohm, +5%, 1/4W 99-211031 Resistor, Carbon Film, 56 Ohm, +5%, 1/4W
99-211032 Resistor, Carbon Film, 1K Ohm, +5%, 1/4W 99-211033 Resistor, Metal Film, 2K Ohm, #2%, 1/4W. 99-211035 Resistor, Carbon Film, 2K Ohm, +5%, 1/4W 99-211077 Resistor, 470 Ohm, 1/2W, +5%
99-211078 Resistor, 120K Ohm, 1W, +5%
Transistors 99-211002 ‘Transistor, NPN, 2SC1413A 99-211003 Transistor, NPN, PE8050B Miscellaneous 99-211059 Heat Sink 99-211061 Heat Sink, 1.5mm 99-211089 Transformer, 4.75 mh 99-211083 Transformer, Power 99-211001 Regulator, UA431AWC 99-211013 Rectifier, Silicon-Controlled, $2800
4-14
Final Lap Upright Mlustrated Parts Lists
N O T E S
Illustrated Parts Lists Final Lap Upright
99-10148 Lock Assembly
99-0160 Coin Inlet Housing
72-HA1404C Screw
S 99-10161 99-10139 n . ]~———— Side Entry Button Assy Coin Door “
99-10115 Spri 99-10148 pring Lock Assembly
; iS J 99-10141 » Coin Return Cover
& 99-10117 Coin Return Door
72-JA1405B 7 TA 9810144 Screw ‘Channel Clip
a 99-15066 Screw
99-10149 Service Door
038091-01 Coin Box
99-10143 Frame
The acceptable substitute for this door (and the one used in games manufactured in Ireland) is the Coin Controls Ltd. Coin Door Assembly, part number 171034-001. You can obtain a free Coin Controls Ltd. supplement (part. no. CO-305-01) that has illustrations and a parts list. Write to Atari Games Ireland Limited, Tipperary Town, Ireland. Telephone 062-52155.
Figure 4-7 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A
4-16
Final Lap Upright Ilustrated Parts Lists
99-10140 Panel Assembly
99-10116 Lever
99-10147 Hames 99-10152 BY Right Coin Inlet ,
17106-0385 a Coin Mechanism
75-944 S Locknut
99-10096 Fastener 99-10151 \ Lett Coin talet SK 7011-47 Lamp
99-10080 Lamp Socket
$9-10105 72-9806S Bar ‘Screw
99-10104
99-10042 thru 99-10045 i I} 99-10154 Coin Switch Assembly
Bracket Assembly
99-10153 Coin Return Box ee-10180 Switch Cover 99-1068 Coin Chute one Kf IC Coin S A \ 99-1075 thru 99-10078 ww | ‘Switch Wires
99-10008 Retainer 75-1412 Screw
Figure 4-7 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A
Illustrated Parts Lists Final Lap Upright
Coin Acceptors, Inc. Coin Door Assembly Parts List
Part No. Description 65-441 Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406 #4-40 x 3/8-Inch Truss-Head Screw 72-HA1404C #4-40 x 1/4-Inch Pan-Head Screw 72JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412 #4-40 x 3/4-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and US, 25¢ 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075, Switch Wire (included in coin switch assembly 99-10043) 99-10076 Switch Wire Gincluded in coin switch assembly 99-10042) 99-10077 Switch Wire (included in coin switch assembly 99-10044) 99-10078 Switch Wire (included in coin switch assembly 99-10045) 99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-1015 Spring 99-10116 Plastic Coin Return Lever
99-10117 Steel Coin Return Door 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10144 Die-Cast Coin Return Cover 99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet
99-10153 Coin Return Box 99-10154 Bracket Assembly 99-10160 1-Inch Wide Die-Cast Coin Inlet Housing 99-10161 25¢ Amber Side-Entry Coin Button Assembly 99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. 25¢
4-18
Final Lap Upright Iustrated Parts Lists
N O T E S
4-19
Illustrated Parts Lists
D2P3 (SSH rer LOS Tez 18106
4-20 R234 259A o1s- TRS6)7 280 191! Final Lap Upright
= I< ul
a snk Be Fo »
e | a So gn j kerteo
VeeEs (00, i ae ee .--4 2802320-E43
¥ FS sens
oo —
| ee | _ | ab he |
| 7 | neo | " |
| 7 | a | IS > 96080356, |
8618961200 oj
| vant | w i | 99-000368 | ° |
i 3
| va | ot | Fer | |
| a | ae | “ | . |
| RF + um | Wher | eye | Fs |
ie 4s ee 5 lee
meses
reas
Figure 4-8 Final Lap CPU PCB Assembly 99-090360
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Illustrated Parts Lists Final Lap Upright
Final Lap CPU PCB Assembly Parts List
Part No. Description Location Integrated Circuits
| 136063-1103 | IC, PR EPROM, Final Lap, SPO | 1K |
| 136063-1104 | IC, PR EPROM, Final Lap, SP1 | 13K |
| 136063-1105 | IC, PR EPROM, Final Lap, CHRO | 11N |
| 136063-1106 | IC, PR EPROM, Final Lap, CHR1 | 11P |
| 136063-1107 | IC, PR EPROM, Final Lap, CHR2 | 11R |
| 136063-1108 | IC, PR EPROM, Final Lap, CHR3 | 11S |
| 136063-1109 | IC, PR EPROM, Final Lap, CHR4 | ON |
| 136063-1110 | IC, PR EPROM, Final Lap, CHR5 | oP |
| 136063-1111 | IC, PR EPROM, Final Lap, CHRO | OR |
| 136063-1112 | IC, PR EPROM, Final Lap, SNDO | val |
| 136063-1113, | IC, PR EPROM, Final Lap, SHAO | 7N |
| 136063-1114 | IC, PR EPROM, Final Lap, VOI1 | 3M |
| 136063-1115 | IC, PR EPROM, Final Lap, VOI2 | 3L |
| 136063-2101 | IC, PR EPROM, Final Lap, MPO | 11D |
| 136063-2102 | IC, PR EPROM, Final Lap, MP1 | 13D |
99-090110 Integrated Circuit, 741804 99-090111 Integrated Circuit, 74LS08 99-090115 Integrated Circuit, 741874 99-090120 Integrated Circuit, 7415157 99-090124 Integrated Circuit, 7418245
| 99-090136 | Integrated Circuit, TMM2018D-45 (45ns) | SL, 5M |
99-090147 Integrated Circuit, YM2151 99-090155 Integrated Circuit, Custom 95 99-90158 Integrated Circuit, DAC, YM3012 99-090244 Integrated Circuit, 7418244 99-090248 Integrated Circuit, Op-Amp, TLO84CN 99-090288 Integrated Circuit, 74F04 99-090291 Integrated Circuit, 74HC175
| 99-090300 | Integrated Circuit, Custom 116 | 4T |
| 99-090303, | Integrated Circuit, Custom 121 | 3 |
99-090313 Integrated Circuit, 74F138 99-090314 Integrated Circuit, 74F244 99-090315, Integrated Circuit, 74F374
| 99-090318 | Integrated Circuit, Custom 123 | 7R |
99-090320 Integrated Circuit, 78L06 99-090322 Integrated Circuit, TA7630 99-090323 Integrated Circuit, LB1760 99-090324 Integrated Circuit, MB3771 99-090362 Integrated Circuit, 74$15 99-090363 Integrated Circuit, 74AC240 99-090364 Integrated Circuit, 74HC74
| 99-090365 | Integrated Circuit, CPU, HD68000-12 | IJ, 3B |
99-090366 Integrated Circuit, CPU, MC68000G12 99-090367 Integrated Circuit, CPU, 68BO9EP
| 99-090368 | Integrated Circuit, CPU, HD68B09E | J |
| 99-090369 | Integrated Circuit, RAM, MB8464A-15-SK | 2K, 6G |
4-22
Final Lap Upright Illustrated Parts Lists
Final Lap CPU PCB Assembly Parts List
Part No. Description Location 99-090370 Integrated Circuit, RAM, MPD4364CX-15 99-090371, Integrated Circuit, RAM, HM6225GP-120 99-090372 Integrated Circuit, RAM, MS5M5256AP-12 99-090373 Integrated Circuit, RAM, MPD4325GC-120 99-090374 Integrated Circuit, RAM, SRM2025GLC12 99-090375, Integrated Circuit, RAM, MB84256-10
| 99-090376 | Integrated Circuit, RAM, M3M5178-55 | 6S, 6T, 6U |
| 99-090377 | Integrated Circuit, RAM, M5M5179-55 | 8A |
99-090378 Integrated Circuit, RAM, MB8422-12
| 99-090379 | Integrated Circuit, RAM, HM6525GBSP-12 | 11E, 13E, |
11M, 13M 99-090380 Integrated Circuit, PAL, 1618, SYS87B-1
| 99-090381 | Integrated Circuit, PAL, 1618, SYS87B-2 | SF |
| 99-090382 | Integrated Circuit, PAL, 12L10-2, SYS87B-3 | 8D |
| 99-090383, | integrated Circuit, EEPROM, HN58C65P-25 | 9D |
| 99-090384 | Integrated Circuit, Custom 137 | 12U |
| 99-090385 | Integrated Circuit, Custom 139 | 8B |
| 99-090386 | Integrated Circuit, Custom 140 | 2M |
| 99-090387, | Integrated Circuit, Custom 145 | 6L |
| 99-090388 | Integrated Circuit, Custom 148 | 13B, 13) |
| 99-090389 | Integrated Circuit, Custom 149 | 2c |
| 99-090390 | Integrated Circuit, Custom 156 | SP |
| 99-090391 | Integrated Circuit, Custom 65 | 3D |
99-090392 Integrated Circuit, Op-Amp, LAG082S 99-090393 Integrated Circuit, Audio Amp, LA4700 99-090394 Integrated Circuit, DAC, LC7880 99-090395 Integrated Circuit, TA7376 99-090396 Integrated Circuit, Voltage regulator, 78L05 99-090398 Integrated Circuit, PC900 99-090399 Integrated Circuit, PC910 Diodes 99-090250 Diode, 181588 99-090326 Diode, 126.2 Inductor 99-090274 Inductor, 100 pH, SP0406-101K Resistors 99-090183 Resistor, SIP, 1 K Ohm x 4, 1/8 W 99-090185 Resistor, SIP, 4.7 K Ohm x 8, 1/8 W 99-090188 Resistor, 680 Ohm, +5%, 1/4 W 99-090189 Resistor, 330 Ohm, +5%, 1/4 W 99-090192 Resistor, 560 Ohm, +5%, 1/4 W 99-090193 Resistor, 1 K Ohm, +5%, 1/4 W 99-090194 Resistor, 4.7 K Ohm, +5%, 1/4 W 99-090196 Resistor, 10 K Ohm, +5%, 1/4 W 99-090199 Resistor, 1 M Ohm, +5%, 1/4 W 99-090252 Resistor, SIP, 2.2 K Ohm x 4, 1/8 W 99-090255 Resistor, 100 Ohm, +5%, 1/4 W
4-23
Ilustrated Pants Lists Final Lap Upright
Final Lap CPU PCB Assembly Parts List
Part No. Description Location 99-090257 Resistor, 2.2 K Ohm, +5%, 1/4 W 99-090305 Resistor, SIP, 100 Ohm, 1/8 W 99-090306 Resistor, SIP, 2.7 K Ohm, 1/8 W 99-090307 Resistor, SIP, 470 Ohm, 1/8 W 99-090309 Resistor, SIP, 1 K Ohm 99-090331 Resistor, 100 K Ohm, 1/4 W, +5% 99-090332 Resistor, SIP, 1 K Ohm, 1/8 W 99-090333 Resistor, SIP, 1.2 K, 1/8 W 99-090336 Resistor, SIP, 10 K Ohm, 1/8 W 99-090351 Potentiometer, 10 K Ohm 99-090400 Resistor, SIP, 4.7 K Ohm, 1/8 W 99-090401 Resistor, SIP, 2.2 K Ohm, 1/8 W 99-090402 Resistor, SIP, 4.7 K Ohm, 1/8 W 99-090403 Resistor, 2.2 Ohm, 1/4 W 99-090404 Resistor, 10 Ohm, 1/4 W 99-090405 Resistor, 22 Ohm, 1/4 W 99-090406 Resistor, 47 Ohm, 1/4 W 99-090407 Resistor, 75 Ohm, 1/4 W 99-090408 Resistor, 220 Ohm, 1/4 W 99-090409 Resistor, 4.7 M Ohm, 1/4 W 99-090410 Resistor, 270 Ohm, 1/8 W Transistors 99-090310 Transistor, 2SA1015-Y 99-090311 Transistor, 2SC2320-E 99-090328 Transistor, 2SC2236-Y 99-090397 ‘Transistor, 2SC1815-Y Capacitors 99-090171 Capacitor, Ceramic, 22 pf, 25V 99-090172 Capacitor, Ceramic, 100 pf, 25V 99-090174 Capacitor, Ceramic, 0.01 uf, 25V 99-090175 Capacitor, Ceramic, 0.1 wf, 25V 99-090180 Capacitor, Ceramic, .033 pf, 50V, +10% 99-090266 Capacitor, Ceramic, .0047 pf, 50V, +10% 99-090267 Capacitor, Ceramic, .01 pf, 50V, +10% 99-090269 Capacitor, Electrolytic, 10 pf, 16V 99-090270 Capacitor, Electrolytic, 47 pf, 16V. 99-090273 Capacitor, Electrolytic, 100 uf, 16V 99-090347 Capacitor, Electrolytic, 22 uf, 16V. 99-090350 Capacitor, Electrolytic, .47 wf, 50V 99-090411 Capacitor, Ceramic, 1000 pf, 25V 99-090412 Capacitor, Ceramic, 3 pf, 25V. 99-090413 Capacitor 99-090414 Capacitor, Ceramic, 0.001 uf, 50V 99-090415 Capacitor, Ceramic, 0.0022 pf, 50V 99-090416 Capacitor, Ceramic, 0.022 uf, 50V 99-090417 Capacitor, Ceramic, 0.12 pf, 50V 99-090418 Capacitor, Electrolytic, 1 wf, 50V
4-24
Final Lap Upright Ilustrated Parts Lists
Final Lap CPU PCB Assembly Parts List
Part No. Description Location 99-090419 Capacitor, Electrolytic, 2.2 yf, 50V. 99-090420 Capacitor, Electrolytic, 100 pf, 10V 99-090421 Capacitor, Electrolytic, 220 wf, 10V 99-090422 Capacitor, Electrolytic, 470 pf, 10V 99-090423 Capacitor, Electrolytic, 2200 pf, 16V 99-090424 Capacitor, Electrolytic, 100 pf, 6.3V Miscellaneous 99-090352 Switch, DIP 8 Circuit 99-090163 Crystal, 3.579545 MHz ic 99-090161 Oscillator, KXO-01-49M152 99-090162 Oscillator, MCO-1425B (49.152 MHz) 13U
4.25
Illustrated Parts Lists Final Lap Upright
semana —| Same) fe ] Sey
| an] | m=] | 1 *% yee] | |||||
| acs | a” | oe | * | af | 7 | * | _ = |
ea Se] | Tse) & Saioase SS] Be 5 satan Ta a
| z | =] | ) ¥ 5 cece | wo] Poe | Se | oe | ee] |
| Be Se] | Tau k* 5~secsoaas _| | tm) oR Sow 1] EF sssoras Be oe oh seasri0s | | ||||
| ™ omar teny | 7, | = | “ | 2 | 4 |
ca C T° Dee F pseosores_e* STE] “29 se-sotas
| CSE - 6421 | twas | ge 5 | ee | ||||
| a | -” | - | aK | ™ | * | ||
| cso] | a | “ | |||||
| fs | Moog & soe | aa] | # Sime ] = koe | ||||
| » | a» | i oars | * [FL care | “ | * | ||
| Tse] iam] | semen | seman, | | | tae Fr] | |||
| E | oye | a | 2 | > pao | " | . | |
| + Sosamoms] * Taaaone] | # Tas | FL oars | ae ae | ||||
| ‘eb. r10 | hoch | P | |||||
| i | = | « | si Be | het | ons | - | * |
| & Semone] #° Taso] = CI | ca | bor] | |||||
| » CI ow» | 2 | » | » | * | |||
| Suse] §* Dive | ier] #* 9. on0136 | . | J | } 2 | al | ||
| ve adh 4 ge | * | « | x | ‘9-cg0s42 |
Yom] g See) Yum ] a+ ae meors i+ Siamese)
86 vi0Eo
4-26 Figure 4-9 Final Lap Video PCB Assembly 99-090361
Final Lap Upright Illustrated Parts Lists
Final Lap Video PCB Assembly Parts List
Part No. Description Location Integrated Circuits
| 136063-1116 | Integrated Circuit, PR ROM, Final Lap, FL3 | 5B |
| 136063-1117 | Integrated Circuit, PR PROM, Final Lap | oR |
| 136063-1118 | Integrated Circuit, PR ROM, Final Lap, OBJOB | SF |
| 136063-1119 | Integrated Circuit, PR ROM, Final Lap, OBJ1B | 4F |
| 136063-1120 | Integrated Circuit, PR ROM, Final Lap, OBJ2B | 5H |
| 136053-1121 | Integrated Circuit, PR ROM, Final Lap, OBJ3B | 4H |
| 136063-1130 | Integrated Circuit, PALIGL8A, FLI-1 | AR |
| 136063-1131 | Integrated Circuit, PALIGL8A, FLI-2 | Oy) |
99-090108 Integrated Circuit, 74LS00 99-090110. Integrated Circuit, 741804 99-090113 Integrated Circuit, 74F20 99-090114 Integrated Circuit, 741832 99-090115 Integrated Circuit, 741874 99-090120 Integrated Circuit, 7419157 99-090122 Integrated Circuit, 7418173 99-090123, Integrated Circuit, 741S174 99-090125, Integrated Circuit, 7418257 99-090128 Integrated Circuit, 7418374 99-090130 Integrated Ciscuit, 7418377 99-090131 Integrated Circuit, 7418378
| 99-090136 | Integrated Circuit, TMM2018D-45 (45ns) | 4C, 4D, 7M, 7N, |
9M, 9N, 99-090244 Integrated Circuit, 7418244 99-090288, Integrated Circuit, 74F04
| 99-090384 | Integrated Circuit, Custom 137 | 7s |
99-090425 Integrated Circuit, 741830 99-090426 Integrated Circuit, 741586 99-090427 Integrated Circuit, 74L$161 99-090428 Integrated Circuit, 7418541 99-090429 Integrated Circuit, 74F00 99-090430 Integrated Circuit, 74F10 99-090431 Integrated Circuit, 74F32 99-090432 Integrated Circuit, 74F74 99-090433 Integrated Circuit, 74F161 99-090434 Integrated Circuit, 74F175 99-090435 Integrated Circuit, 74F240 99-090436 Integrated Circuit, RAM, TMM2018AP-25 99-090437 Integrated Circuit, RAM, HM6716-25
| 99-090438 | Integrated Circuit, RAM, MB8464-10-SK | 4P, 4R, 48, 47 |
| 99-090439 | Integrated Circuit, RAM, MB81464-12 | 1E, 1F, 2E, 2F |
| 99-090440 | Integrated Circuit, Custom 45 | 2K |
99-090441 Integrated Circuit, Custom 106
| 99-090442 | Integrated Circuit, Custom 107 | 5C |
| 99-090443 | Integrated Circuit, Custom 134 | 4N |
| 99-090444 | Integrated Circuit, Custom 135 | ST |
Illustrated Parts Lists Final Lap Upright
Final Lap Video PCB Assembly Parts List
Part No. Descriptioa Location 99-090445 Integrated Circuit, Custom 146 7F Resistors 99-090193 Resistor, 1 K Ohm, +5%, 1/4 W 99-090332 Resistor, SIP, 1 K Ohm, 1/8 W 99-090406 Resistor, 47 Ohm, 1/4 W 99-090446 Resistor, SIP, 47 Ohm, 1/4 W Capacitors 99-090344 Capacitor, Electrolytic, 470 uf, 10V 99-090447 Capacitor
4-28
Final Lap Upright Illustrated Parts Lists
220 uF/6.3V
136063-1129 136063-1128 OBJ3BH OBJ2BH peed cord
136063-1127 136063-1126 OBJ3BL OBJ2BL pcedt pcs]
136063-1125 136063-1124 OBJ1BH OBJOBH pcafb pes}
136063-1123 136063-1122 OBJIBL OBJOBL pc2-{} eciff
2272961700
Figure 4-10 Final Lap Small ROM PCB Assembly 99-090452 Final Lap Small ROM PCB Assembly Parts List
Part No. Description Designator 99-090453 Capacitor, 220uF, 6.3V Cl 136063-1122 Integrated Circuit, ROM, Motion Object 0 BL 136063-1123 Integrated Circuit, ROM, Motion Object 1 BL 136063-1124 Integrated Circuit, ROM, Motion Object 0 BH 136063-1125 Integrated Circuit, ROM, Motion Object 1 BH 136063-1126 Integrated Circuit, ROM, Motion Object 2 BL 136063-1127 Integrated Circuit, ROM, Motion Object 3 BL 136063-1128 Integrated Circuit, ROM, Motion Object 2 BH 136063-1129 Integrated Circuit, ROM, Motion Object 3 BH 99-090416 Capacitor, Ceramic, 0.022 HF, 50 V PC1-PC8
4-29
Ilustrated Parts Lists Final Lap Upright
iii, Iii ua,
ro}
(2272963200)
fe} ie}
Figure 4-11 Final Lap EMI PCB Assembly 155027-001
Parts List
Part No. Description
179174-056 Connector, Edge, 56 Ckt 99-090448 Filter, EMI, 270 pf, Ferrite 99-090449 Filter, EMI, 2200 pf, Ferrite
4-30
Final Lap Upright
This assembly drawing was not available at press time. Contact your Atari Games Customer Service Office for a copy of this drawing.
Figure 4-12 Final Lap Link PCB Assembly Illustrated Parts Lists
155028-001
Parts List
Part No. Description 99-090450 Relay 99-090325 Diode, 181885 99-090451 Switch, Slide
4-31
Illustrated Parts Lists Final Lap Upright
N O T E S
4-32
Neale ele pele pele pele fel ed pele pel fe fel el pel el eel pele el el relfelelfelelpelel
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted, If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller's plant; and
- Seller's examination of said products discloses to Seller's action that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller. EPP Eee eee eee ase eee eee ele eae ealelealelelelelrelrel PAPE eee eee eee eee ee eee eee ele eelelelelelelel
Pee eee eee eee eee eee eee leet!
The use of any non-Atari parts may void yo warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others, Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. ur Warranty, according to the terms of the
Atari distributors are independent, being privately owned and operated, In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.