CATHODE RAY TOMES

Donkey Kong 3

Donkey Kong 3 (US) (Nintendo of America, 1983) · Manual · 57 pages · 21 sections · original scan

Page 1

Nintendo-Pak"

FOR ee COREY FOG

Page 2
WARNING This instruction manual is for use only by authorized distributors of Nintendo of America inc., coin operated video arcade games who have been licensed to install replacement parts and components in Nintendo arcade games pursuant to Nintendo-Pak™ license agreements.
WARNING If the replacement parts and components in this Nintendo-Pak™ are not installed exactly as instructed herein, there may be radio frequency interference created in violation of F.C.C. class A standards.
WARNING This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a class A computing device pursuant to subpart J of part 15 of F.C.C. rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipmentin a residential area is likely to cause interference; in which case, the user at his own expense will be required to take whatever measures may be required to correct the interference.
WARNING Use of non-Nintendo parts or modifications to your Nintendo-Pak™ parts and components may adversely affect the safety of your game, and may cause injury to your players.
Page 3

VIL.

Vill. TABLE OF CONTENTS

Introduction

Contents of Nintendo-Pak™

List of Tools Needed

Replacement Process Step-by-Step

Final Check Sheet and Adjustments

Donkey Kong 3 Wiring Diagram

Service Bulletins

CPU P.C., VIDEO P.C., and Power Supply Schematics

Reorder Parts Lists 4-5

7-22

23-31

32-33

34-40

41-43

44-55

Page 4

|. INTRODUCTION

Nintendo-Pak™

NINTENDO-PAK™ enables you to replace Donkey Kong*, Donkey Kong Jr.* or Popeye** with Donkey Kong 3% in less than one hour.

Before you begin, be sure you are properly prepared. Make certain you have selected the right NINTENDO-PAK™ for the particular game you are replacing. Next, thoroughly read this instruction manual to familiarize yourself with the proper procedures. Make certain that you have all the tools necessary to complete the process.

If you have any questions, please call Nintendo Service at 1-(800)-633-3236.

  • Donkey Kong, Donkey Kong Jr., Donkey Kong 3 and Nintendo-Pak are trademarks of Nintendo of America Inc.

** A trademark of King Features Syndicate, Inc.

Page 5

Contents of Nintendo-Pak

Parts Name Quantity Remarks

Pak (A) Basic Pak

DKC1 Complete P.C. Board

C-DKC-US Complete Operation Panel Assembly

DKC-US Plate 600W

DKC-US Screen 600W

DKC-US Side Decal

Nintendo-Pak™ Manual with harness aya aaa

Pak (B) Donkey Kong and Donkey Kong Jr.

FCC Shield Cage 1 051 Shield Cage Cover Complete Assembly 1 with FCC Harness

Serial Number Plate 1

DKC-UP Back Door Adjustment Label 1 with double back tape

FCC Class A Label 1

C-UP44P-044 Edge Connecting Main Harness 1

Ground Cable E 1

Machine Screw with Washer M4 X 10 6

Round Head Wood Screw 3.5 x 13 13

Sticker Tie Down 2

Cable Tie 2

FBI STICKER 1

Authorized Donkey Kong 3 sticker 1

Page 6

Il. Contents of Nintendo-Pak (Cont’d.)

Parts Name Quantity Remarks

Pak (C) Popeye

821B-7B Power Assembly 1 TKGU-08-01 DJRU-19-01

051 Shield Cage Cover Complete Assembly Serial Number Plate

DKC-UP Back Door Adjustment Label Video Monitor Mounting Bracket (Upper) Video Monitor Mounting Bracket (Lower) Video Monitor L Bracket

9P-030 Power Harness

12P-030 Power Harness

Blind Cardboard (Large) Blind Cardboard (Small) Fuse 5A 125V

Fuse 4A 125V

5A Fuse Label

Machine Screw with Washer M5 X 30

M5 Washer (Large) Hex Nut with Washer MS

Carriage Bolt M6 X 30 Hex Nut with Washer M6

Machine Screw with Washer M5 X 16

Round Head Wood Screw 3.5 X 13 FBI Sticker

Authorized Donkey Kong 3 Sticker

Hole Template =3-2 4p NY BROTHA BAH BoB nn py ann inn with FCC harness

with double back tape

with double back tape with double back tape

Page 7

Ill. List of Tools Needed

Flat (standard) screwdriver

Phillips screwdriver

7mm nut driver

8mm nut driver

10mm nut driver

Ya" or 6.5mm drill bit

15/64 or 5.5mm drill bit

Electric reversing drill

Phillips bit (for drill)

Staple gun

Paper stapler

Lacquer thinner

Denatured alcohol or other cleaner

Note: Many steps require the use of a phillips screwdriver and having a phillips screwdriver bit for your drill will greatly speed up these steps.
Page 8

IV. Step-by-step instructions

  • Exchange marquee/header (see illustration 1-1)

A. Remove four (4) top trim screws B. Exchange marquee plexiglass C. Replace top trim and four (4) top trim screws

  • Remove old control panel and front screen (see illustration 1-2)

A. Undo control panel holddown clamps B. Disconnect harness and remove control panel C. Remove front screen by sliding back front screen clamp (access from back door)

Page 9

These steps are for Donkey Kong and Donkey Kong Junior ONLY.

Note: If replacing Popeye, proceed to step 6.
  • Remove instruction label (see illustration 1-3)
Note: For Donkey Kong, Donkey Kong Jr. ONLY

A. Spray label with lacquer thinner B. Wait 15 minutes and remove with putty knife C. Clean area with cloth and lacquer thinner

  • Replace side decal (see illustration 1-4)
Note: For Donkey Kong and Donkey Kong Junior only

A. Remove all carriage bolts. B. Remove old decals.

Page 10

These steps are for Donkey Kong and Donkey Kong Junior ONLY.

C. Clean side panel with alcohol and install new Donkey Kong 3 side decal.

Note: Decal is placed 2-1/2 inches from top and in center of side panel. (See illustration 1-5) SEE DECAL APPLICATION SHEET, PAGE 22.

D. Replace all carriage bolts. (See illustration 1-6)

IMPORTANT: Be sure that monitor ground wire is connected to one of the locations shown.
Page 11

These steps are for Donkey Kong and Donkey Kong Jr. ONLY

  • Installation of FCC shield cage (see illustration 1-7)

A. Unscrew wing nuts and remove P.C. Board assembly and all wire harnesses EXCEPT three (3) harness connections to coin door (2 pin counter, 3 pin coin, 5 pin service) B. Remove P.C. Board mounting brackets

C. If P.C. Board wood shelf has slots made from square stock wood, remove these (see illustration 1-8)

Page 12

These steps are for Donkey Kong and Donkey Kong Jr. ONLY

D._ Install new FCC shield cage so it is flush with rear of wood shelf and fasten with nine (9) screws provided. IMPORTANT! On lower left corner install ground harness and connect the other end to the mounting bolt on the power supply as shown. (see illustration 1-9 & 1-10)

These steps are for Popeye ONLY

  • Replacement of side decal and vertical positioning of monitor (see illustration 2-1)

A. Remove both large and small blind cardboard.

W

Page 13

These steps are for Popeye ONLY.

B. Disconnect all monitor connections and mounting screws and remove monitor (see illustration 2-2).

Note: Monitor ground wire will be reconnected in Step K. C. Remove all carriage bolts and monitor side panel supports (see illustration 2-2). D. If your game does not have 5 holes in each side panel, use the template provided to drill upper two holes (see illustration 2-3).

E. Remove old side decals and clean side panels with alcohol. F. Install new side decals 2-1/2 inches from top and in center of side panel (see illustration 2-4).

SEE DECAL APPLICATION SHEET PAGE 22

Page 14

These steps are for Popeye ONLY

G. IMPORTANT: Check to see if your game has the lower monitor support installed. If it does, skip step H and proceed to step | (see illustration 2-5).

H._ Install lower monitor support by drilling three (3) 15/64 (5.5m) holes and mounting support with three (3) M5 machine screws and cap nuts (see illustration 2-6).

Page 15

These steps are for Popeye ONLY

|. Place monitor back into game in vertical position.

Note: Monitor frame rests in front of lower monitor support (see illustration 2-7).

Install all side panel carriage bolts. Install upper monitor support L brackets and monitor support bar. (Note: Monitor support bar provided in PAK AC.) IMPORTANT: RECONNECT MONITOR GROUND IN POSITION SHOWN IN DETAIL (see illustration 2-8). AS

Page 16

These steps are for Popeye ONLY

L. Install monitor mounting machine screws (see illustration 2-9).

M. Install new small and large blind cardboard, being sure to staple where shown (see illustration 2-10).

Page 17

These steps are for Popeye ONLY

  • If you are replacing a Popeye game, remove old power supply transformer assembly (see illustration 2-11 & 2-12).

Disconnect connector from switch plate Disconnect both plugs from monitor and lamp Disconnect ground harness connections Disconnect both power harness connections

IMPORTANT: Take off old short harness connectors and replace with new short harness connectors provided. SEE DETAIL (illustration 2-11). Remove four (4) wing nuts and take out old power assembly. Replace with new Donkey Kong 3 power supply assembly and tighten wing nuts.
Note: Bolts for wing nuts may push through bottom of game during mounting of new power supply unit. If this happens, simply push them back up when power supply assembly is in place G. Reconnect Steps A, B & C being careful to get a good connection on Step C. Ground harnesses. 9Om>

mm

  • Replace fuse with 5 AMP fuse and place 5 AMP fuse label in position shown (see illustration 2-11).
Page 18

This step is for Popeye only.

9, Remove old Popeye P.C. Board and FCC cover assemble (see illustration 2-13).

These are steps for Donkey Kong, Donkey Kong Junior and Popeye.

  • Install new Donkey Kong 3 P.C. Boards and new FCC cage cover assemble, and connect short harness to P.C. Board. IMPORTANT: Do not screw on cover until final adjustments are completed (see illustration 3-1).
Page 19

This step is for Popeye, Donkey Kong and Donkey Kong Jr.

  • Connect main harness assembly (see illustration 3-2)
Note: For Donkey Kong and Donkey Kong Junior, install new wire harness (steps A-G). For Popeye, reconnect old harness (steps D, E and G).

A. Connect 2 pin, 3 pin, 4 pin coin door harnesses to mah harness

(Note: Harnesses are different for Popeye, Donkey Kong, and Donkey Kong Jr.) B. Fasten control panel connectors to wire tie approximately 5" from connectors Route the main harness through existing wire ties and then install two (2) new stick-on ties to FCC shield cage to hold harness securely Connect 4 pin sound and 6 pin video from monitor to main harness Connect 9 pin and 10 pin power supply connectors Fasten power supply harness to fCC shield cage with cable ties. Connect 44-pin edge connector to FCC cover assemble. ammo

DONKEY KONG DONKEY KONG JR.

DONKEY KONG DONKEY KONG JR.

Page 20

These steps are for Popeye, Donkey Kong and Donkey Kong Jr.

  • Connect new Donkey Kong 3 control panel to main harness and fasten down control panel (see illustration 3-3)
Note: For Donkey Kong and Donkey Kong Jr., use white connector on main harness only.
  • Install new Donkey Kong 3 front screen and fasten with front screen clamp

A. IMPORTANT! Place authorized Donkey Kong 3 sticker on front screen in location shown (see illustration 3-3)

  • Screw on new serial number plate next to old plate.
IMPORTANT! Do not remove old plate (see illustration 3-4)

A. Use round head wood screw 3.5 x 3 provided.

Page 21
  • Attach FCC Class A label (see illustration 3-5)

A. Remove old FCC label B. Put on new FCC label and staple all four corners

Note: This step in not necessary for Popeye.
  • Attach FBI sticker

A. Place label on back door just under lock (see illustration 3-6)

B. Staple all four corners.

3-6

Page 22

This step is for Donkey, Donkey Kong Jr., and Popeye.

  • Attach new back door adjustment label

A. Peel off old label and replace with new Donkey Kong 3 label. Staple all four corners (see illustration 3-7)

3-7

Page 23

Side Decal Application

Step 1.

Start by peeling the protective backing “A” down about 6 inches from the top.

Place decal in desired position. Pull down slowly the remainder of the protective backing of “A.”

While doing this, use a soft cloth to smooth decal onto side board, moving from top to bottom of decal.

Step 2.

Fold remaining decal back, exposing the unprinted side. Begin to peel protective backing “B” from center to right hand side “slowly.”

Using soft cloth smooth decal onto side panel by running hand from top to bottom of decal, moving outward to the right hand side.

Front View

Page 24

oooo00ou0dao go NOOR WD

Oo @

O 10.

O 11.

O 12. V. FINAL CHECK SHEET AND ADJUSTMENTS

Replacement label installed (MANDATORY)

FBI sticker installed (MANDATORY) New serial number plate installed (MANDATORY)

New FCC label installed (MANDATORY)

New adjustment label installed

Fuse label changed (Popeye only) P.C. Board adjustments made (see PC Board adjustments page 24-25)

Monitor adjustments made (see monitor adjustments pages 26-27)

Self test check (see pages 28-29)

Coins give credit Controls on operational panel functioning

Sound checked

Page 25

K ADJUSTMENTS

After powering up the game, you may find that the horizontal width and vertical height need adjustment. To make adjustment to the horizontal width, refer to the illustration on page 26. To adjust the vertical height, use the V-size adjustment on the rear of the monitor to make the picture larger.

It may also be necessary to adjust the vertical and horizontal position controls on the video p.c. board as shown below to center the picture.

P.C. Board Adjustments

Adjustment of Semi-Fixed Resistors

VIDEO P.C. Board

Semi-fixed resistors, VR1 and VR2 on VIDEO P.C. Board are used to adjust video monitor screen.

castles VR1 VR2

DKC1-01-Video

VIDEO P.C. Board

vBi SOK2 1/3W vy - nos move clockwise i fi . white knob a io move picture up i : _ AS owe cocknse | ———_1_— move clockwise SOKQ2 1/3W 4 to move picture left white knob ~ Pos

Page 26

Option Switch Settings

DKC1 CPU P.C. BOARD

Toggle (SW1) Settings

Number of Players Per Game

30.000PTS. 40.000PTS. 50.000PTS. NO EXTRA Additional 30.000PTS. Extra 40.000PTS. 50.000PTS. NO EXTRA Difficulty Easy i ¢ (3) Hard (4)

Coin/Credit

Game Test ON Upright Table

WARNING

All the Option Switch Settings MUST be done with power off.

Page 27

Adjustment of Horizontal Width

Caution! High Voltage Area — BE CAREFUL!

Using a standard 2.6mm hex non-conductive core alignment driver, carefully turn L453 counter-clockwise for a smaller horizontal screen size. L453 is located in the rear of the monitor just under the deflection yoke.

Alignment Tool

\

Heat Sink

Turn this way for a smaller horizontal screen size

CAUTION! HIGH VOLTAGE! BE CAREFUL
Page 28

Adjustment of Video Monitor

From To Game PCB Green Gaw _ Video Monitor 6P—600 Video Red Gain x Main PCB Harness, Blue Gam Signal PCB

INVERT OUT NON INVERT OUT

This Signal PCB is only attached to TPPU-20-00

:Video Monitor [32 Type] 20-EZV (R-C),

BRIGHT,

SOUND VOLUME

H HOLO Fuse 44 Slow Blow SF

@ “a

Video Monitor Man PCB

Fuse 0.38 Midget Type

Video Monitor

WARNING

Do not touch the inside of the Video Monitor. It contains many parts supplied with high voltage.

Page 29

()

(2)

(3)

(4) Bookkeeping and Self-Test

Entry Press Service Switch and hold it down until Menu of Test Mode displays on the Video Monitor as follows.

Test Mode

1 Bookkeeping Distributions 2 Free Play 3 Self-Test & Monitor Adjustment 4 Return To Game Mode

Selection of Test A flashing Buzzbee points to the Test. Momentarily depressing Service Switch will step to next Test. When the Buzzbee is pointing to the desired Test, the details of the Test can be displayed by pressing the Service Switch and holding it down until the details appear on the Video Monitor. (Except “Return To Game Mode”)

Back to Menu of Test Mode

You can recall Menu of Test Mode by holding down Service Switch until it re-appears.

Back to Game Mode

When the Buzzbee is pointing to “Return To Game Mode”, you will be able to return to Game Mode (Demonstration Game) by holding down Service Switch until it re-appears.

(WARNING) Test Mode will go back to Game Mode automatically if you do not push a switch or button or move the controller within a few minutes.

Page 30

A. Bookkeeping Distributions:

  • Playtime distributions and number of plays per distribution range.
  • Score distributions and number of plays per distribution range.
  • To clear all distributions, press either start button. ** Bookkeeping distribution system will not function when game is set in Free Play Mode.

B. Free-Play Pressing either start button will set or clear “FREE PLAY” mode.

C. Self-Test & Adjustment Pressing either start button will step to the next Test. (C-1) RAM and ROM Test The result of RAM and ROM Test will be displayed on the Video Monitor as follows.

Example

RAM ROM TEST ROM CHECKSUM OK 7B OK OK OK (OK: Passed) OK NG (NG: Failed) RAM location ROM location on the PCB on the PCB

C-2 CRT Test Color Bar and Marks on four Corners and center of screen are displayed on the Video Monitor one after another.

C-3 Sound Test You will hear the various sounds one after another.

C-4 Switch Test The result of the switch condition will be displayed on the Video Monitor when you press each of the switches or move the controllers.

C-5 End of Self-Test.

Page 31

Maintenance

Fuse Replacement This game contains 4 fuses. Replace fuses only with the same type as listed below.

Specification of Fuses

  • Main Fuse U.S.: 5A 125V (90-120V)
  • Power Supply Fuse 4A 125V
  • Video Monitor Fuse 4A 125V 0.3A 125V

Cleaning The exterior of the game, all metal parts and all plastic parts can be cleaned with a nonabrasive cleanser. You should be careful when cleaning the plastic parts. A dry cloth may cause scratches which will result in a foggy appearance.

Electrical Rating

Voltage: 120 (V)

Frequency: 60 (HZ)

Wattage: 120 (W)

Current: 1.3 (AMP)

Page 32

Switch Maintenance

Micro-Switch Replacement Whenever you replace any micro-switch on the Operation Panel, a switch gap adjustment is needed as shown below.

| Switch Button Assy.

\\ Micro-switch Gap: 0.2 0.5mm/1/128 5/256inch)

i

Switch gap adjustment

Lubrication for 2 way Controller To maintain the 2 way Controller in good condition, lubricate the pillow balls and 2 way Guide Plate approx. every 3 months. See Fig. 9.

Lubricate here//

Page 33

-5v

VI. Donkey Kong 3 Wiring Diagram

1OP-130 POWER HARNESS

-5V -5V -5V GND GND GND GND +5V IN

P4 POWER

+5V

VIDEO PCB DOKC-VIDEO

Pl

P2 SoPp-40 FLAT CABLE

50P-40 FLAT CABLE

P4 POWER OUT

CPU PCB DKC-CPU 44P-O51-FCC PCB HARNESS

lc lolxr}a|njolmlalo

al* o

° Ofrda Slala Zl<|< Ss >|o]>

alala

>|ol> ojala COINI 2PLAYER IPLAYER 2P_RIGHT 1P_RIGHT 2P_ LEFT (P_LEFT OS!I-OI-FCC PCB

!

! !

a cy

PI

P2 Ty

Page 34

C-uP44P EDGE CONNECTING HARNESS io [—orance | ra] rs fe] BLUE ia [al ia] [a] iS] [Puree 1°16 a [BLACK | BLACK fidid

BROWN RED [ [| oRANGE YELLOW BLACK Les BLUE, ce

| BLACK

YELLOW YELLOW GREEN GREEN ot AZURE. AZURE ot BLACK BLACK PT-8218 PT-8A

FLUORESCENT LAMP 10W

INVERT OUT

z 2 = a no w ge g gee g ac =x se ar a g & orZz 5 OF =z ar oO 2 o- & fo] 8 8 a EE] 9 &

wo o

3P COIN

HARNESS

VIDEO MONITOR SIGNAL PCB NON INVERT OUT

VIDEO MONITOR SOUND PCB

VIDEO MONITOR

2P SPEAKER TV HARNESS 2P SPEAKER

Page 35

Nintendo

SERVICE DEPARTMENT

Dear Distributor:

In addition to the steps you have already done, we felt it would benefit your customers if the previous common problems were checked to ensure the modifications had been done. Below is the list of service bulletins which deal with these problems.

We have included copies of these service bulletins:

TKG-05 DJR-O1

DJR-02

DJR-O5

Sincerely,

Nintendo of America Inc. Service Department Slam Switch Upper Coin Door Hinge Model 730A Coin Selector Video Wrap Around

1-800-633-3236 Ss 4-206-882-2040

Page 36

Nintendo

SERVICE DEPARTMENT

BULLETIN # TKG.O5

GAME: Donkey Kong, Donkey Kong Junior, Popeye, Mario Bros. Donkey Kong 3

SUBJECT: Slam Switch

In order to prevent the accumulation of free credits by kicking the coin door, a slam switch should be added.

In all cases the switch (a "normally should be mounted on the coin door. slam switch to the brown wire on the other side of the slam switch should which will be run through the wiring At this point the installations vary

Donkey Kong: open" weighted reed switch) Connect one side of the coin switch (ground). The be connected to a wire harness to the CPU board. for the five (5) games.

TKG2 and TKG3: Attach to Test Point 8, at board coordinates 3L.

TKG4: Attach to Test Point 2-RESET, at board coordinates IL.

Donkey Kong Junior:

Attach to Test Point 2-RESET, at board coordinates 1L.

Popeye:

Attach to C13 (47MF electrolytic capacitor), "+" side, at board coordinates 2N.

Mario Bros.:

Attach to C38 (100MF electrolytic capacitor), "+" side, at board coordinates 4F.

Donkey Kong 3:

Attach to C25 (100AVF electrolytic capacitor), "+" side, at board coordinates 2E.

1-800-633-3236 ee 1-506-882-2040

Page 37

SERVICE DEPARTMENT

BULLETIN # DJR-01

GAME: Donkey Kong Junior, Donkey Kong, Radar Scope

SUBJECT: Upper Coin Door Hinge

It has been brought to our attention that a flattened straw or similar object can be passed through the center opening in the upper hinge. If the object makes contact with the coin switch, it can be used to run up multiple credits.

The solution is to block the opening with a flange made of wood or metal. This flange should be mounted to the inside of the cabinet and can be obtained from us as a retrofit kit.

This problem is present in all Radar Scope uprights, Donkey Kong uprights and early Donkey Kong Junior uprights.

1-800°633°3236 S7?_._.3Qc 1-206-882-2040

Page 38

ebueld woned = HY IW NIOD Vid

fa) io . LMS ADAG NO FONE (IN LNNOW :FLON

Sel 235077 Vi | @ | FD JOM NAHI a 29M SYROP? FIV OF (@ GLI Give GLYN 2NULSIKT FINISN H29W MIO? L771

\ STIGIEIG

JINVE MAN

Page 39

SERVICE DEPARTMENT

BULLETIN # DJR-02

GAME: Donkey Kong Junior

SUBJECT: Model #730A Coin Selector

It has come to our attention that there is a problem with the model #730A coin selector in that a nickel or a penny, if flipped through the entry just right, will continue through the mechanism and establish credits.

The solution to this problem is to add two small metal pieces to the selector as shown in the accompanying drawing. These pieces are available at no charge. The threaded holes in the selector is an M3 X 6MM size.

1-800°633°3236 3..." 1-206-882-2040

Page 40

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 41

SERVICE DEPARTMENT BULLETIN * = pgr.-05

GAME: Donkey Kong, Donkey Kong Junior

SUBJECT: Video Wrap Around on Left Side of Picture

We have recently received a number of service calls concerning the wrap around or fold over of the picture on the left hand side of the monitor. In most cases the problem may be solved by replacing capacitor C407 on the main monitor PC board. This is located just to the left of the high voltage cage when viewing from the rear of the monitor. The value of this capacitor is 10 microfarads at 160 volts (of course, any capacitor of 10 microfarads with a voltage rating higher will work also).

This capacitor is connected between ground and the B+ supply for the vertical output transistors, so if this capacitor becomes leaky it does not allow full vertical deflection of the screen; consequently, you get video information imposed over the other (wrap around).

If you have questions about this or any other questions concerning Nintendo products, please feel free to contact us.

1°3900 -633-23236 " 1-206-882-2040

Page 42

wy

a

Donkey Kong 3 - CPU

Page 43

Donkey Kong 3 - Video

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

IX. REORDER PARTS LIST

PARTS LIST: DKCI-UP Game Cabinet Assembly (See Fig. 1)

ITEM PARTS NO. DESCRIPTION

1DJRU-01-01Body (Wooden Game Cabinet)
2DKCU-12-16DKC-US Display Panel (Name Plate)
3TKGU-01-29Fluorescent Lamp Assy.
4DKCU-12-15DKC-US Front Screen
5TKGU-01-53Front Screen Frame (Lower Retainer)
6DKCU-23-60DKC-US Complete Operation Panel Assembly
7TKGU-01-31Operation Panel Clamp A (2 Required)
8TKGU-01-01-03Cash Box
9TKGU-01-28Coin Door Assy.
10TKGU-01-04Coin Door Lock
1DJRU-01-02Coin Selector: Order By Currency
12DJRU-01-02-01Coin Switch: Order By Coin Selector
13TKGU-01-11Game Countor
14TKGU-01-33Service Switch
15TKGU-01-64Service Switch Bracket
16TKGU-01-43Speaker

PARTS LIST: DKCI-UP Game Cabinet Assembly (See Fig. 2)

ITEM PARTS NO. DESCRIPTION

1TKGU-01-01-05Rear Panel
2TKGU-01-03Rear Panel Lock
3DJRU-01-68Blind Cardboard (Small)
4DJRU-01-67Blind Cardboard (Large)
5DJRU-20-00Video Monitor (20-5F)
6DKCU-22-01DKC1-VIDEO Complete PCB Assy.
7DKCU-21-01DCK1-CPU Complete PCB Assy.
8TPP2-01-20Dual Locking-head PCB Spacer 10N (8 Required)
9TPPU-01-01-10Shield Cage
10DKCU-11-11051 Shield Cover
11DKCU-23-01051 FCC Complete PCB Assy.
12TKGU-01-65Strain Relief Bushing Plate
13TKGU-01-10Strain Relief Bushing
14TKGU-01-08Power Cord: Order By Voltage & Plug Type
15TMAU-30-12Power ON/OFF Switch Assy. (For 90-120V)

TMAU-30-13 Power ON/OFF Switch Assy. (For 200-240V)

16DJRU-18-01PP-7B Complete Power Supply Assy.
17DJRU-19-01-01PT-821B Power Transformer (For 90-120V)

DJRU-09-01-01 PT8A Power Transformer (For 200-240V)

18TKGU-01-01-02Transformer Base B
19TKGU-09-01-03Terminal Block 6-Position Type

TKGU 19-01-03 Terminal Block 4-Position Type

20TKGU 09-01-02Outlet Through Isolation Transformer
21TKGU-01-30Caster (2 Required)
Page 46

PARTS LIST: DKC1-UP Operation Panel Assembly (See Fig. 3)

ITEM PARTS NO. DESCRIPTION

1DKCU-14-11Complete 4 way Controller Assy.
2TKGU-23-514 way Guide Plate
3TKGU-23-23E Ring 4
4TKGU-23-21Switch Collar
5TKGU-23-22Lever Spring
6TKGU-23-20Spring Stopper
7TKGU-23-13Micro-switch VL 12L (Bent) (4 Required)
8TKGU-23-17Switch Spacer (4 Required)
9TKGU-23-16Bearing Bracket
10TMAU-12-15Lever Plate
anTMAU-12-14Control Knob Plate 28D
12TMAU-12-16Controller Knob Collar 8L
13TMAU-11-18Knob with Shaft 80.5L
14TKGU-23-34Pal Nut (4 Required)
15TKGU-23-26Nut Plate (4 Required)
16TKGU-23-12Sutton Bracket (3 Required)
17TMAU-34-18Micro-switch VL 12L (Straight) (4 Required)
18TMAU-12-18Collar 34 X 28 X 7H
19TMAU-11-28Operation Panel Fastener B 50W
20DKCU-12-11DKC-US Operation Panel
21TKGU-23-31Blue Button Assy. (For 1P, 2P Button)
22TKGU-23-32Orange Button Assy. (For Spray Button)

PARTS LIST: DKC1-UP Wiring Harness

ITEM PARTS NO. DESCRIPTION

1TMAU-41-17C-UP 44P044 Edge Connecting Harness
2DKCU-41-1144P 051-FCC PCB Harness
3DJRU-13-074P-750 Audio Harness (750 mm)
4DJRU-13-316P-1000 Video Harness (1000 mm)
5DJRU-13-022P Counter Harness (820 mm)
6DJRU-13-055P Service Switch Harness (1,150 mm)
7DJRU-13-043P Coin Harness (850 mm)
8TKGU-13-062P Speaker TV Harness [2p-370] (370 mm)
9TKGU-13-172P Speaker Harness [2P-860] (860 mm)
10TPPU-93-10UP-42 Type 15P-Operation Panel Harness
1DJRU-13-1250P Flat Cable [50P-40]
12TPPU-93-1110P-130 Power Harness (130 mm)
Page 47

PARTS LIST: DKC1-CPU PCB Assembly

NO. DESCRIPTION (Reference Designation and Location) DKCU-21-01 DKC1-CPU Complete PCB Assembly

DKCU-21-11Z80A Microprocessor(5C)
DKCU-21-12Z80A DMA Controllor(5B)
DKCU-21-13PC2A03 Microprocessor(4M,5J)
DKCU-21-142764 8K byte EPROM 350ns DKC1-C-7B(7B)
DKCU-21-152764 8K byte EPROM 350ns DKC1-C-7C(7C)
DKCU-21-162764 8K byte EPROM 350ns DKC1-C-7D(7D)
DKCU-21-172764 8K byte EPROM 350ns DKC1-C-7E(7E)
DKCU-21-182764 8K byte EPROM 350ns DKC1-C-6H(6H)
DKCU-21-192764 8K byte EPROM 350ns DKC1-C-5L(5L)
DKCU-21-286116 2K byte C-MOS RAM 200 ns(7H)
DKCU-21-212115 2K byte RAM 200ns(5K, 6E, 7F)
DKCU-21-22LM3900 Audio Amplifier(6P)
DKCU-21-23TBP28S42N 512 X 8bit Bipolar ROM(1D)
DKCU-21-24MB7053 512 X 4bit Bipolar ROM(1C)
DKCU-21-25TBP18S030 32 X 8bit ROM(5E)
DKCU-21-2674LS00 Quad 2-Input NAND(2H)
DKCU-21-2774LS04 Hex Inveter(3F, 3K, 4B)
DKCU-21-2874LS27 Triple 3-Input NOR(3C)
DKCU-21-2974LS32 Quad D-Type Flip-Flop(2B)
DKCU-21-3074LS74 Dul D-Type Flip-Flop(2D, 3H)
DKCU-21-3174LS123 Dual Retriggerable Single Shot(3J)
DKCU-21-3274LS138 3 To 8 Demultiplexer(2A, 3A, 4E, 4F)
DKCU-21-3374LS139 Dual 2 To 4 Line Decoder(3B)
DKCU-21-3474LS174 Hex D-Type Flip-Flop(3B)
DKCU-21-3574LS240 Octal Invertor Buffer(1B, 2C, 5H)
DKCU-21-3674LS244 Octal 3 State Bus Buffer(2L, 2M, 3L, 3M)
DKCU-21-3774LF245 Octal Bus Transceiver(6E, 7A)
DKCU-21-3874LS259 8-bit Addressable Latches(5A)
DKCU-21-3974LS367 HEX Bus Driver(SE, 4A, 6A)
DKCU-21-4074LS374 Octal 3-State D-Type Flip-Flop(4H, 4J, 5F)
DKCU-21-41PST518 Reference Voltage Detector(8Q)
DKCU-21-422SA564 PNP Transister(Q3, Q4, Q7)
DKCU-21-432SD592 NPN Transistor(Q9)
DKCU-21-442SC828 NPN Transistor(Q1, Q2, Q5, Q6, Q10)
DKCU-21-4518953 Diode(D3, D5, D6)
DKCU-21-46W03B Diode(D1, D2, D4)
DKCU-21-4727 Ohm 1/4W Resistor(R64)
DKCU-21-4868 Ohm 1/4W Resistor(R29, R31, R382, R34)
DKCU-21-49100 Ohm 1/4W Resistor(R17, R18, R21, R36,

R37, R53, R54)

DKCU-21-50200 Ohm 1/4W Resistor(R20)
DKCU-21-51220 Ohm 1/4W Resistor(R1, R7, R12)
DKCU-21-52330 Ohm 1/4W Resistor(R19, R23, R24, R25,

R28, R30, R33)

DKCU-21-58390 Ohm 1/4W Resistor(R69)
DKCU-21-54470 Ohm 1/4W Resistor(R6, R10, R11, R15,

R16, R22)

Page 48

NO. DESCRIPTION (Reference Designation and Location)

DKCU-21-55510 Ohm 1/4W Resistor(R67, R68)
DKCU-21-56560 Ohm 1/4W Resistor(R70, R71)
DKCU-21-57680 Ohm 1/4W Resistor(R59)
DKCU-21-581K Ohm 1/4W Resistor(R2, R5, R8, RY, R13, R35)
DKCU-21-592K Ohm 1/4W Resistor(R3, R4, R14, R26)
DKCU-21-602.2K Ohm 1/4W Resistor(R61)
DKCU-21-613.3K Ohm 1/4W Resistor(R62)
DKCU-21-6210K Ohm 1/4W Resistor(R27, R41, R46, R47)

(R57, R65, R72, R73)

DKCU-21-6312K Ohm 1/4W Resistor(R38, R55, R58)
DKCU-21-6420K Ohm 1/4W Resistor(R39, R56)
DKCU-21-6533K Ohm 1/4W Resistor(R63, R66)
DKCU-21-66100K Ohm 1/4W Resistor(R48, R68)
DKCU-21-67300K Ohm 1/4W Resistor(R43)
DKCU-21-68750K Ohm 1/4W Resistor(R42, R44, R50)
DKCU-21-691M Ohm 1/4W Resistor(R49, R51)
DKCU-21-701.8M Ohm 1/4W Resistor(R45)
DKCU-21-712.2M Ohm 1/4W Resistor(R48, R52)
DKCU-21-72Hex 68 Ohm 1/4W Resistor Array(RM2, RM3, RM5, RM6)
DKCU-21-73Octal 1K Ohm 1/4W Resistor Array(RM1, RM4)
DKCU-21-74Octal 4.7K Ohm 1/4W Resistor Array(RM7, RM8)
DKCU-21-7551pF 50V Ceramic-Disc Capacitor(C26)
DKCU-21-76100pF 50V Ceramic-Disc Capacitor(C17, C18)
DKCU-21-770.01uF 50V Ceramic-Disk Capacitor(C1, C22, C45, C46,

C47, C47)

DKCU-21-780.1uF 50V Ceramic-Disc Capacitor(C2-C16, C27, C44)
DKCU-21-790.047uF 50V Film Capacitor(C20, C21)
DKCU-21-8010uF-16V Tantalum Radia Capacitor(C28)
DKCU-21-8110uF-16V A1 Electrolytic Radial Capacitor(C19, C29, C31,

C32, C33, C34)

DKCU-21-8247uF 16V A1 Electrolytic Radial Capacitor(C23)
DKCU-21-83100uF 16V A1 Electrolytic Radial Capacitor(C24, C25)
DKCU-21-84470uF 16V A1 Electrolytic Radial Capacitor(C30, C42, C43)
DKCU-21-838-MHz Crystal(X2)
DKCU-21-8621.47727-MHz Crystal(X1)

DKCU-21-87 NC5884-09 Minbus Bar DKCU-21-88 16 Pin DIP IC Socket DKCU-21-89 20 Pin DIP IC Socket DKCU-21-90 28 Pin DIP IC Socket DKCU-21-91 40 Pin DIP IC Socket

DKCU-21-928-Station Single-Throw DIP Bit Switch(SW1, Swe)
DKCU-21-93GP-7 Ferrite Beads(FC1-FC13)
DKCU-21-9410Pin Connector Receptacle(P3)
DKCU-21-9550Pin Flat Cable Header(P1, P2)

DKCU-21-96 Battery Case TYPE 32-4 UM-3 X 2 DKCU-21-97 Philips Head Machine Screw (With Spring Washer M2.6 X 8)

Page 49

NO. DESCRIPTION (Reference Designation and Location) DKCU-21-98 Flat Washer M2.6 DKCU-21-29 Nut Plate M2.6 DKCU-21-100 Beabed Wire Tie DKCU-21-101 Dry Battery Size AA (UM-3)

PARTS LIST: DKC1-VIDEO PCB Assembly

NO. DESCRIPTION (Reference Designation and Location)

DKCU-22-01 DKC1-VIDEO Complete PCB Assembly

DKCU-22-112732 4K byte EPROM DKC1-V-3P(3P)
DKCU-22-122732 4K byte EPROM DKC1-V-3N(3N)
DKCU-22-132732 4K byte EPROM DKC1-V-7C(7C)
DKCU-22-142732 4K byte EPROM DKC -V-7D(7D)
DKCU-22-152732 4K byte EPROM DKC1-V-7E(7E)
DKCU-22-162732 4K byte EPROM DKC1-V-7F(7F)
DKCU-22-1774LS00 Quad 2-Input NAND(4K, 5A)
DKCU-22-1874LS02 Quad 2-Input NOR(2J, 6A, 6L)
DKCU-22-1974LS04 Hex Inverter(1J, 1K, 5H, 6B, 7L, 8L)
DKCU-22-2074LS08 Quad 2-Input AND(5R)
DKCU-22-2174LS10 Triple 3-Input NAND(7A)
DKCU-22-2274LS20 Dual 4-Input NAND(2L, 5B, 6F, 7N)
DKCU-22-2374LS30 8 Input NAND(6P)
DKCU-22-2474LS32 Quad D-Type Flip-Flop(5d)
DKCU-22-2574LS74 Dual D-Type Flip-Flop(2K, 4A, 4B, 4L)
DKCU-22-2674LS86 Quad 2-Input Exclusive-OR(3D, 3R, 4D, 4R,

5D, 6D, 7H)

DKCU-22-2774LS109 Dual J-K-Flip-Flop(8N)
DKCU-22-2874LS123 Dual Retriggerable Single Shot(3B)
DKCU-22-2974LS139 Dual 2 To 4 Line Decoder(5F)
DKCU-22-3074LS157 Quad 2-Line to 1-Line Data Selector(2S, 3J, 3L, 3M, 3S, 4J, 4M,

5M, SN, 6S, 7S, 8B, 8S)

DKCU-22-3174LS161 4-bit Binary Countor(5C, 5K, 6C, 6K)
DKCU-22-3274LS163 4-bit Binary Countor(3E, 4E)
DKCU-22-3374LS174 Hex D-Type Flip-Flop(2M)
DKCU-22-3474LS175 Quad D-Type Flip-Flop(5E, 6E)
DKCU-22-3574LS245 Octal Bus Transceiver(1S, 5S)
DKCU-22-3674LS273 Octal D-Type Flip-Flop(6J, 6M, 6N, 8H)
DKCU-22-3774LS283 4-bit Binary Fll Adder(7J, 7K, 7P, 7R,

8J, 8K, 8P, 8R)

DKCU-22-3874LS299 8-bit Shift Registors(4N, 4P, 8C, 8D, 8E, 8F)
DKCU-22-3974LS367 HEX Bus Driver(1P, 1R)
DKCU-22-4074LS373 Octal 3-State D-Latches(3K, 6H)
DKCU-22-4174LS377 Octal D-Type Flip-Flop(6K)
DKCU-22-4274LS161 Schottkey 4-bit Binary Countor(1L, 1M, 1N)
DKCU-22-43MB10105 Triple 2-3-2 Input OR/NOR(1F)
DKCU-22-44MB10116 Triple Line Receivers(1D)
DKCU-22-45MB10124 Quad TTL-to-ECL Translators(3C, 3H, 4C, 4H)
Page 50

NO. DESCRIPTION (Reference Designation and Location)

DKCU-22-46MB10125 Quad ECL-to-TTL Translators(1H, 3F, 4F)
DKCU-22-47MB10136 Universal Hexadecimal countor(1E)
DKCU-22-48MB7074 ECL-RAM with Radiator Fin(2E, 2H)
DKCU-22-49MB93419 64 X 9-bit Bipolar RAM(7M)
DKCU-22-50MB8114 1024K X 4-bit MOS RAM(2P, 2R)
DKCU-22-51MB8148L55 1024K X 4-bit Bipolar RAM(6P, 6R)
DKCU-22-5224510 256 X 4-bit Bipolar PROM(2N)
DKCU-22-55510 Ohm 1/4W Resistor(R3, R6, RY, R10, R12-R18, R24)
DKCU-22-581K Ohm 1/4W Resistor(R11, R19, R25-R46)
DKCU-22-592.2K Ohm 1/4W Resistor(R7, R8, R47, R48)
DKCU-22-684.7K Ohm 1/4W Resistor(R20, R22)
DKCU-22-6110K Ohm 1/4W Resistor(R1, R2)
DKCU-22-6210K Ohm 1/4W Resistor(R4, R5)
DKCU-22-6322K Ohm 1/4W Resistor(R21)
DKCU-22-6427K Ohm 1/4W Variable Resistor(R23)
DKCU-22-6550K Ohm 1/3W Variable Resistor(VR1, VR2)
DKCU-22-66Octal 510 Ohm 1/4W Resistor Array(RM1, RM3-RM5)
DKCU-22-67Octal 1K Ohm 1/4W Resistor Array(RM2)
DKCU-22-6810pF 50V Ceramic-Disc Capacitor(C8, C15)
DKCU-22-6933pF 50V Ceramic-Disc Capacitor(C5)
DKCU-22-7068pF 50V Ceramic-Disc Capacitor(C16)
DKCU-22-7147pF 50V Ceramic-Disc Capacitor(C3)
DKCU-22-72220pF 50V Ceramic-Disc Capacitor(C12, C145, C146, C147)

DKCU-22-73 330pF 50V Ceramic-Disc Capacitor

DKCU-22-740.01uF 50V Ceramic-Disc Capacitor(C4, C6, C7,

C19-C141, C13)

DKCU-22-750.1uF 50V Film Capacitor(C11)
DKCU-22-760.01uF 50V Film Capacitor(C14)
DKCU-22-770.022uF 50V Film Capacitor(C17, C18)

DKCU-22-78 1uF 50V Al Electrolytic Radial Capacitor

DKCU-22-79220uF Al Electrolytic Radial Capacitor(C1, C2, C9, C10)

DKCU-22-90 61.44-MHz Crystal

PARTS LIST: DKC1-FCC CB Assembly

NO. DESCRIPTION (Reference Designation and Location)

DKCU-23-01 DKC1-FCC Complete PCB Assembly DKCU-23-11 W-P0736 36-Pin Connector DKCU-23-12 0.01uF 50V Ceramic-Disc Capacitor DKCU-23-13 0.001uF 50V Ceramic-Disc Capacitor DKCU-23-14 5pF Ceramic-Disc Capacitor

Page 51

PARTS LIST: DKC1-FCCC PCB Assembly

NO. DESCRIPTION (Reference Designation and Location)

DKCU-24-01 (PP7B) Power PC Board Complete Set

DKCU-24-112SC2555 NPN Transistor(TR1)
DKCU-24-122SA817 PNP Transistor(TR2, TR4)
DKCU-24-132SC2535 NPN Transistor(TR3)
DKCU-24-142SA1015 PNP Transistor(TRS)
DKCU-24-15CTV-2S-Fast Recovery Center Tap Diode(D4)
DKCU-24-16CTB33S Schottky Diode(D5, D9)
DKCU-24-17S4UB40 4A/400UW Silicon Rectifier Diode(BR1)
DKCU-24-181B4B41 Silicon Rectifier Diode(BR2)
DKCU-24-193D-1001 Hybrid IC(IC1, IC2)
DKCU-24-207824 3-Terminal Regulator(IC3)
DKCU-24-217812 3-Terminal Regulator(IC4)
DKCU-24-225P4M Thyristors(SCR1)
DKCU-24-23O3P05M Thyristors(SCR2)
DKCU-24-2418954 Diode(D1, D6, D10, D11)
DKCU-24-2510DF-4 Diode(D2, D3, D7, D8)
DKCU-24-26PC614 Poto Coupler(iC5)
DKCU-22-2705Z5.6V Zener Diode(2D1)
DKCU-24-28052Z5.1L Zener Diode(2D2)
DKCU-24-2905Z5.6Z Zener Diode(ZD3)
DKCU-24-30470pF 2KV Ceramic-Disc Capacitor(C1, C2, C9)
DKCU-24-310.1uF 50V Ceramic-Disc Capacitor(C29)
DKCU-24-320.047uF 630V Film Capacitor(C3, C4, C5)
DKCU-25-330.01uF 50V Film Capacitor(C8, C17)
DKCU-25-341000pF 50V Film Capacitor(C14, C26)
DKCU-25-351000uF 50V Al Electrolytic Capacitor(C10)
DKCU-25-3647uF 35V Al Electrolytic Capacitor(C11, C13)
DKCU-25-3747uF 16V Al Electrolytic Capacitor(C12, C18, C19, C28, C30,

C31, C32, C36, C37, C38)

DKCU-25-283300uF 10V Al Electrolytic Capacitor(C27, C28, C15, C16)
DKCU-25-39100uF 25V Al Electrolytic Capacitor(C23, C33)
DKCU-25-4010uF 16v Al Electrolytic Capacitor(C22, C24, C25, C34, C35)
DKCU-25-41330uF 200V Al Electrolytic Capacitor(C6, C7)
DKCU-25-421000uF 25V Al Electrolytic Capacitor(C21)
DKCU-25-4320 Ohm 2W Resistor (Coil Winding)(R1)
DKCU-25-441K Ohm 1/4W Resistor(R2, R12, R15, R15, R18, R22)
DKCU-25-4551 Ohm 1/4W Resistor(R38, R4, R11, R15,

R17, R19, R21, R23)

DKCU-25-4612 Ohm 1/2W Resistor(R5, R8, R20, R24, R6, R26)
DKCU-25-47470 Ohm 1/4W Resistor(R10)
DKCU-25-4822 Ohm 1/2W Resistor(R13)
DKCU-25-4920K Ohm 1/2W Resistor(R16, R25)
DKCU-25-50100 Ohm 1/2W Resistor(R27)
DKCU-25-5120 Ohm 5W Resistor(R9)
DKCU-25-52510 Ohm 3W Resistor (Metal Oxide)(R7)
DKCU-25-5350K Ohm GPO6P Variable Resistor(VR2, VR4)
DKCU-25-542K Ohm GPO6P Variable Resistor(VR1, VR3)
DKCU-25-555m Ohm Shunt Resistor(SH1, SH2)
DKCU-25-56SC-02 SC Coil(L1)
Page 52
  • Power P.C.Board
No.Name of PartsQ’ty | Remarksee
DJR-18-01(PP-7B) Power P.C.Board.1Complete Set
DJR-18-02Transistor128C2555
DJR-18-03Transistor2 | 2SA817
DJR-18-04Transistor1| 28C2535
DJR-18-05Transistor1 | 2SA1015
DJR-18-06Fast Recovery Center1CTU-2S

Tap Diode

DJR-18-07Shot Key Diode2 | CTB33S
DJR-18-08Silicon Rectifier Diode1S4VB40 4A 400VW
DJR-18-09Silicon Rectifier Diode11B4B41
DJR-18-10Hybrid IC2 | 3D-1001
DJR-18-113 Terminals Regulators17824
DJR-18-123 Terminals Regulators1| 7812
DJR-18-13Thyristors|SP4M
DJR-18-14Thyristorsi03P05M
DJR-18-15Diode418954
DJR-18-16Diode410DF-4
DJR-18-17Photo Coupler1PC614
DJR-18-18Zener Diode1| 05Z5.6U
DJR-18-19Zener Diode1 | O5Z5.1L
DJR-18-20Zener Diode105Z5.6Z
DJR-18-21Ceramic Capacitor3 | DEO707B471K2K 470pF2KV
DJR-18-22Ceramic Capacitor10.1MF SOV
DJR-18-23Film Capacitor3| MDD2J473M 0.047MF 630VW
DJR-18-24Film Capacitor2 | 0.01IMF SOV
DJR-18-25Film Capacitor21000pF SOV
DJR-18-26Aluminum Electrolytic Capacitor}11000MF 50V
DJR-18-27Aluminum Electrolytic Capacitor)2 | 47MF 35V
DJR-18-28Aluminum Electrolytic Capacitor]747MF 16V
DJR-18-29Aluminum Electrolytic Capacitor)43300MF 10V
DJR-18-30Aluminum Electrolytic Capacitor}2100MF 25V
DJR-18-31Aluminum Electrolytic Capacitor}510MF 16V
DJR-18-32Aluminum Electrolytic Capacitor,2330MF 200V
DJR-18-33Aluminum Electrolytic Capacitor,11000MF 25V
DJR-18-34Resistor (Coil Winding):120 OHM 2W
DJR-18-35Resistor (Carbon)51K OHM 4W+5%
DJR-18-36Resistor (Carbon)8 | 51 OHM “4Wts%
DJR-18-37Resistor (Carbon)6 | 12 OHM AWt5%
DJR-18-38Resistor (Carbon)1| 470 OHM 4We5%
DJR-18-39Resistor (Carbon)122 OHM 2W+5%
DJR-18-40Resistor (Carbon)2 | 20K OHM 4Ws5%
Page 53

FOB Japan No. Name of Parts Q’ty | Remarks per pe.

DJR-18-41Resistor (Carbon)1100 OHM %W
DJR-18-42Resistor (Cement)120 OHM SW
DJR-18-43Resistor (Metal Oxide)1510 OHM 3W
DJR-18-44Variable Resistor2.|50K OHM GFO6P
DJR-18-45Variable Resistor2 | 2K OHM GFOoP
DJR-18-46Shunt Resistor2 | 5m OHM
DJR-18-47SC Coil1SC-02
DJR-18-48SF Coil2100MH SA
DJR-18-49SF Coil2 | 800MH 2A
DJR-18-50Oscillator Transformer1EC-35 Type 3D-0097
DJR-18-51Oscillator Transformer1 | EI-30 Type 3D-0097
DJR-18-52Oscillator Transformer2 | EE-16 Type 3D-1000
DIJR-18-53Fuse Element1FGMB 4A 125V NR Type
Page 54

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 55

Rear View of Game Cabinet Fig. 2

Page 56

Fig. 3

Page 57

PRINTED IN U.S.A.