Tournament Table TM-113 1st Printing
Tournament Table (set 1) (Atari, 1978) · Technical Manual · 98 pages · 48 sections · original scan
\st PRINT NG
Operation, Maintenance and Service Manual! Complete with Illustrated Parts Catalog
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the TV monitor chassis. Please mention this number whenever calling your distributor for service.
TOURNAMENT
TABLE'
Operation, Maintenance and Service Manual
ATARI INC 1265 BORREGAS AVENUE BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 * TELEX 35-7488
A
ATARI
A Warner Communications Company
Copyright © 1978 by Atari, Inc. All rights reserved
Motorola and TEC service manuals reprinted by permission of Motorola Data Products and TEC Videoelectronics, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission request, write:
ATARI INC
- 1265 Borregas Avenue P.O.Box 9027 Sunnyvale, California 94086
3G Lithographed in the U.S.A.
TABLE OF CONTENTS
1 Puprotinidi SETUP INTRODUCTION GAME INSPECTION .. LOCATION OF SERIAL NUMBER INSTALLATION REQUIREMENTS .. Power Requirements and Line Voltage Selection Temperature Range . Humidity Range .... Location Space Requirements Type of Power Cord .... E. INTERLOCK SWITCHES F, VOLUME CONTROL .. G. SELF-TEST PROCEDURE H. poe>
|. GAME TESTS OPERATOR OPTIONS .
2 GAME VLAY ATERACE MODE esis sens esas cn cost viele ee ete ete ome eee ede READY-TO-PLAY MODE ... PLAY MODE Breakout Soccer | Soccer ll .. Foozpong ... Hockey! .... Hockey Il . Hockey Ill .. Quadrapong Handball .. Volleyball . Basketball | Basketball II ... ap>
3 aris aan AND ADJUSTMENT CLEANING . COIN MECHANISM . Components on Coin Door . Access to Coin Mechanisms . Cleaning of Coin Paths Lubrication ...........6605 Adjustment of Coin Switch Trip Wire .. Mechanical Adjustments on Coin Mechanism . General Troubleshooting Hints . FUSE REPLACEMENT ...... . TV MONITOR ADJUSTMENTS. TV MONITOR REMOVAL .....+ LED SWITCH AND POTENTIOMETER REPLACEMENT ™moo NADDUUHARARWWA
iii
TABLE OF CONTENTS
4 reer OF OPERATION >mOOR> GENERAL INFORMATION . POWER SUPPLIES CRYSTAL OSCILLATOR AND TV SYNC COUNTDOWN CHAINS ... MICROCOMPUTER MICROCOMPUTER WATCHDOG . VIDEO OUTPUT
5 ILLUSTRATED PARTS CATALOG... 2... 0.0.0.0.0.... 37
6 TV MONITOR SERVICING INFORMATION
. THEORY OF OPERATION ..
. HORIZONTAL DEFLECTION CIRCUITS ...
. GENERAL . SPECIFICATIONS MOTOROLA Service Manual . GENERAL INFORMATION .. . SERVICE NOTES ....... Circuit Tracing. Component Removal CRT Replacement .. Adjustments ... Regulator Adjustment .. Horizontal Hold/Oscillator Adjustment . Vertical Height/Linearity Adjustment Focus Adjustment . Monitor Servicing .
Power Supply +73 Volt Supply Video Amplifiers and Output .
Phase Detector Horizontal Oscillator .. Horizontal Pulse Shaper and Driver HorizontaJ Output Sync Circuits ...... Vertical Oscillator and Output .. Spot Killer Blanking Amplifier TEC Service Manual
Power Supply Input ... Power Consumption Video Input
TABLE OF CONTENTS
Picture Tube .. High Voltage Horizontal Retrace Time .. Resolution ........... Scanning Frequency .. Tone Burst Amplifier . Environment
LIST OF ILLUSTRATIONS
Figure 1-1 Tournament Table Control Panel 2 Figure 1-2 Location of Voltage-Changing Plugs on the Power Supply .. 4 Figure 1-3 Location of Interlock Switches, Self-Test Switch, and Volume Control 6 Figure 1-4 Option Switches on Game PCB . - 10 Figure 2-1 Typical TV Monitor Display During Attract Mode .. 4 Figure 2-2 Typical TV Monitor Display During Ready-to-Play Mode . 4 Figure 2-3. Typical TV Monitor Display During Play Mode . 4 Figure 2-4 Location of Player Controls 215 Figure 3-1 Coin Door Assembly ......... - 20 Figure 3-2. Hinging Open the Magnet Gate Assembly . 20 Figure 3-3 Removal of Coin Mechanism ......... - 27 Figure 3-4 Surfaces to Clean Inside the Coin Mechanism . » 27 Figure 3-5 Removal of Plate Covering Rear of Coin Slot 27 Figure 3-6 Close-Up View of Lubrication Point - 22 Figure 3-7 Detail View of Coin Switch and Trip Wire ... . 22 Figure 3-8 Securing the Coin Switch Wire .... 22 Figure 3-9 Adjustments on Coin Mechanism . 23 Figure 3-10 Locations of Adjustments on TV Chassis . 24 Figure 3-11 TV Monitor Removal ..........06... 00005 . 25 Figure 3-12 LED Switch and Potentiometer Replacement . . 26 Figure 4-1 Tournament Table PCB Block Diagram - 28 Figure 4-2. Game Block Diagram - 29 Figure 4-3. Tournament Table Schematic Diagram (2 sheets)
LIST OF ILLUSTRATIONS
Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7
Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-5 Figure 6-6 Figure 6-7 Figure 6-8 Figure 6-9 Figure 6-10 Motorola Monitor Vertical Oscillator Circuit .. Figure 6-11 Motorola Monitor Spot Killer Circuit Figure 6-12 Motorola Monitor Blanking Amplifier Circuit . Figure 6-13 Motorola Monitor Chassis Rear View—Component Location Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View Figure 6-15 ILLUSTRATED PARTS CATALOG
Tournament Table Final Assembly .. . 38 TV Shelf Assembly .. 42 Control Panel Assembly .. . 44 Tournament Table PCB Assembly Coin Door Assembly ...........- wee 52 Power Supply Assembly Harness Schematic - 56
TV MONITOR SERVICING INFORMATION
Motorola Monitor Circuit Board in Service Position .. - 61 Motorola Monitor Block Diagram - 62 +73 Volt Supply Circuit ..........4- - 62 Motorola Monitor Vertical Drive Waveform - 62 Motorola Monitor Video Amplifiers and Output Circuit - 63 Motorola Monitor Horizontal Deflection Circuit ..... . 64 Motorola Monitor Horizontal Deflection Waveforms . + 65. Motorola Monitor Horizontal Output Circuit . - 65 Motorola Monitor Sync Circuit ............ - 66
Motorola Monitor Schematic Diagram ..............4- Figure 6-16 Motorola Monitor Circuit Board Detail—Component Location 71 Figure 6-17 TEC Monitor Chassis, Rear View . . 76 Figure 6-18 TEC Monitor Chassis, Top View .. . 76 Figure 6-19 TEC Monitor Printed Circuit Board, Top View Figure 6-20 TEC Monitor Schematic Diagram . Figure 6-21 TEC Monitor Wiring Diagram
LIST OF TABLES
vi Table 1-1 Table 1-2 Table 1-3 Table 6-1 Table 6-2 Table 6-3 Game/Option Designations . Self-Test Procedure Operator Options Motorola Monitor Electrical Specifications Motorola Monitor Replacement Part Numbers . TEC Monitor Replacement Part Numbers
LOCATION SETUP
A. INTRODUCTION Tournament Table™ is a collection of 12 paddle games contained in Atari’s cocktail table cabinet. A 19-inch black-and-white TV monitor is mounted in the center of the cabinet and is tilted slightly forward from a horizontal position. The TV monitor is surrounded by a Plexiglas’control panel on top of the game cabinet. The control panel includes:
© Four sets of player controls
- ONE-PLAYER START button (LED switch) See © TWO-PLAYER START button (LED switch) ) Figure © FOUR-PLAYER START button (LED switch) 1-1 @ GAME SELECT button (LED switch)
tA3LE” counn AMENt
‘ONE PLAYER TWO. ‘START SU PLAYER FOUR PLAYER) rART ‘START sonTiGn!
LED LED SWITCH SWITCHES POTENTIOMETER
Figure 1-1 Tournament Table Control Panel
The GAME SELECT button is functional at all times except during game play. The start buttons can be activated after the proper amount of coins have cleared the coin acceptor. Each set of player controls consist of an OPTION CONTROL button (LED switch), and a potentiometer. The potentiometer controls the vertical or horizontal movement of the paddle. The OPTION CONTROL button is used to control one of three ball/paddle features (except in Breakout where it functions as a ball serve control).
Tournament Table offers three options/features, each one designated for specific games. See Table 1-1 for Game/Option Designations. The three option/ features are:
¢ WHAMMY: Puts sharp angles on the ball when the OPTION CONTROL button is pressed and held down. If the button is released immediately it appears to distort the direction and speed in which the ball is traveling. Has no effect when the ball is traveling in a direct horizontal line across the screen.
© CATCH: Causes the ball to stick to the paddle when the OPTION CONTROL is pressed and held down. Players can use this feature to aim a hit, pass toa team paddle, or plan strategy. When the button is released the ball will release. The angle at which the ball leaves the paddle depends on which section of the paddle the ball is caught.
= \ \ \ WV I
} V
Table 1-1 Game/Option Designations
Option No. of Game WHAMMY™ }CATCH™ | JUMP | BALL SERVE Players = BREAKOUT x 1or2
| SOCCER | | x | 2or4 |
SOCCER II 4 FOOZPONG 2or4
| HOCKEY | | x | 2or4 |
HOCKEY I] 2or4 HOCKEY HII 4 QUADRAPONG NO OPTION 2or4
| HANDBALL | x | 2or4 |
VOLLEYBALL x 2or4 BASKETBALL | xX 2or4 BASKETBALL II x L | 2or4
Itis possible to “scrape” the ball off the paddle by moving the paddle through the edge of the playfield and back.
¢ JUMP: This feature causes the paddle to jump vertically from the bottom of the playfield to the playfield center when the OPTION CONTROL button is pressed and held down. The paddle will return to its home position when the button is released. The paddle must be jumped before the ball passes through the playfield center or the ball will travel through the paddle instead of bouncing off the paddle. All of the games (except Breakout, Soccer II and Hockey III) have a two- or four-player version (see Table 1-1). The object in all games is to obtain the highest score when the game ends. You may select a game end score of 11 or 15 points for all games except Breakout. (See Table 1-3, Operator Options.) There is a time limit of ten minutes for all games except Breakout. A three- or five-ball game is optional for Breakout and there is no time limit. (However, if the player does not push the serve button within 16 seconds, the ball is served automatically.) In Breakout the bricks will refill the playfield indefinitely when they are all hit, and the player has aturn or turns remaining. It is also the only game which includes replay. (See Table 1-3 for Breakout replay levels.) Chapter 2 contains a detailed description of game play for all games.
B. GAME INSPECTION Tournament Table is manufactured by Atari with the intent of being ready to play immediately upon removal from the shipping carton. Your cooperation is needed to supply the final touch of quality control. Please follow the procedures below to ensure that your game is in perfect condition.
- Examine all external parts of the game cabinet for dents, chips, or broken parts.
- After determining that the game has been received in good condition, unlock and remove the rear door assembly. Carefully inspect the interior and verify that:
- All plug-in connectors are firmly seated.
- All integrated circuits in sockets on the game printed circuit board are firmly seated. © The fuses are all seated in their holders. © No harness wires are disconnected.
- No loose foreign objects are present, especially metal objects that could cause electrical problems.
Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speaker, the player controls, and the TV monitor chassis.
C. LOCATION OF SERIAL NUMBER The serial number for Tournament Table is located in the corner (common to both edge connectors) on the back of the PCB, inside the game cabinet. See the illustration on the inside front cover of this manual.
D. INSTALLATION
REQUIREMENTS
Power Requirements and Line Voltage Selection Tournament Table is shipped for operation at 110 VAC, 60 Hz. Power consumption is approximately 150 watts. However, if your local voltage is not 110 volts, follow this procedure. You must select one of four connectors at the power supply and plug it into the voltage selection socket. Figure 1-2 shows the four connectors, with one of them plugged in. The plugs are identified by wire color as listed in this figure.
[;— LINE VOLTAGE-CHANGING VOLTAGE PLUG WIRE COLOR 95 VAC BLACK Pree Taal installed at factor 210 VAC 220 VAC
ON/OFF AND Cc INTERLOCK SWITCH
3Amp, 250 Vv. Stow - blow tion, measure line voltage. If voltage is consistently below 100 V (for 110 VAC lines) or below 210 V (for 220 VAC lines), use the low-voltage connections. Use the black plug for low 110 VAC lines and the green plug for low 220 VAC lines.
Temperature Range Location and storage should not be below 0 degrees Celsius (32 degrees Fahrenheit), and no higher than 49 degrees Celsius (120 degrees Fahrenheit).
Humidity Range Relative Humidity for location or storage should be no more than 95%
8 Amp, 125V. ‘Voltage - Change Plugs Fast-Blow
2.5 Amp.125 V. Slow—blow
Figure 1-2 Location of Voltage-Changing Plugs on the Power Suppy
Location Space Requirements
Cabinet Dimensions: Top: Height—76 centimeters (30 inches) Width—85 centimeters (33% inches) Depth—76 centimeters (30 inches) © Base: Width—60 centimeters (23% inches) Depth—45 centimeters (18 inches)
Type of Power Cord Atari has added a strain relief power cord to Tournament Table. The advantage of this type of power cord is that, if pulled accidentally, the strain relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector. Check the power cord assembly periodically for damage.
E. INTERLOCK SWITCHES To minimize the hazard of electrical shock while you are working inside the game cabinet, an interlock switch has been installed at the rear door assembly and at the coin door. These switches (2) remove all power from the game while one or both of the doors are open. Refer to Figure 1-3 for switch locations.
Check for proper operation of the interlock switches by performing the following steps:
1, Unlock and remove the rear door assembly. Unlock and open the coin door. . Plug the AC power cord into a 110-volt source. (If the voltage is consistently less than 110 VAC, make sure that you change the voltage plug to the black plug.)
- Close both doors. Within approximately 30 seconds the TV monitor should display a picture.
. Slowly open each door (individually) until the TV monitor picture disappears. The TV monitor pic- ‘ture should disappear when each door is opened less than one inch.
. If the results of Step 4 are satisfactory, the interlock switches are operating properly. If the picture does not disappear as described, check to see if one of the switches is broken from its mounting or stuck in the on position.
. Close and lock the rear door assembly. Close and lock the coin door.
F. VOLUME CONTROL To adjust the volume it is necessary to remove the rear door assembly and locate the game PCB on the right side of the cabinet wall. The volume control may be adjusted without removing the PCB from the cabinet. See Figure 1-3 for location of the volume control.
G. SELE-TEST PROCEDURE Tournament Table will test itself and provide data to demonstrate that the game’s circuitry and controls are working properly. The self-test procedure uses the TV monitor and the speaker; no additional equipment is required. The self-test switch is located on the game PCB, as shown in Figure 1-3. (The rear door assembly must be removed whenever it is necessary to work with the PCB.)
Table 1-2 contains specific details on the self-test procedure. To start the procedure over from the beginning, push the self-test switch up, then again to the down position. This will return the test to Step 1, and can be done at any time during the procedure. We suggest that you run the self-test procedure each time the coin box is emptied.
H. GAME TESTS
Four-Player Games If the paddles are vertical:
- PLAYER 1 and 3’s control will turn counter clockwise to move the paddle up the screen. © The other controls will turn clockwise to move the paddle up the screen.
If the paddles are horizontal: © All controls will turn clockwise to move the paddles to the right. For error correction, check the harness hookup to the potentiometer .
INTERLOCK SWITCHES (2) GAME PCB
SELF-TEST @ j switch
VOLUME CONTROL
Figure 1-3 Location of Interlock Switches, Self-Test Switch, and Volume Control
Breakout, One-Player © Start the game and check for the ball count remaining on the screen during game play. © Check the ball sounds for:
- Serve
- Paddle hit
- Brick hit
- Ball out
- When the ball goes out, the game should not shift to the other player. Error correction—possible ROM error, audio output chip error (LM 380) if no sound atall, or error in part C010744.
Breakout, Two-Player © Start the game and check to see if the ball count is replaced by SCORE after the ball is served.
- Check to see if the game shifts to the other player when the ball goes out.
Error correction—possible ROM error.
Soccer I, Four-Player Start the game and check to see that each player has two paddles.
- Check the WHAMMY feature.
Error correction: possible ROM error, or error in part CO10744.
Soccer II, Four-Player © Start the game and check to see that each player has one paddle.
- Check the CATCH feature.
Error correction: possible ROM error, or error in part C010744.
Foozpong, Four-Player Start the game and check for multiple vertical paddles. Error correction: possible ROM error. © Check the CATCH feature
Error correction: possible bad switch or line.
Hockey TI, Two-Player © Start the game and check to see that each player has three paddies. Error correction: Possible ROMerror, or error in part C010744.
Volleyball, Four-Player
- Start the game and check to see that there are two smal\ and two large horizontal paddles. Error correction: possible ROM error, or error in part C010744.
- Check the jump feature. Error correction: Possible bad switch or line.
I. OPERATOR OPTIONS The options programmed for Tournament Table offer maximum player appeal for each game location. These options are listed in Table 1-3.They are preset for a certain game setup during production. To determine how the switches have been set for your game, compare the TV monitor screen during the self-test mode with the information in Table 1-3.
To change the toggle positions of the DIP switches and set the options you desire, remove the rear door assembly and locate the game PCB on the right cabinet wall. Refer to Figure 1-4 for locating the option DIP switches on the game PCB.
Set the switches for the desired options, as shown in Table 1-3. Verify option functions by playing the game.
Table 1-2 Self-Test Procedure
Test Instruction Results if Test Passes Results if Test Fails
1 Unlock and remove the | The TV monitor screen will show the fol- ROM is bad, the TV monitor will display a LETTER CODE and corresrear door assembly. lowing display: ponding strips on both sides of the screen. The following error screen Locate the self-test ROM status patterns represent the failing ROMs, as they would appear on the
slide switch on the TEST TV monitor:
on EIS, am il ti 1 £ © a jie Sa We Qi a loc RAM status 1. ROMA: A 2, ROM 1: B 3 ROMB& IEC
igure 1-3. OK “FHlocation C4/5
OK. RAM? status
Set the self-test switch A B c
to the “on” position. |
ROM and RAM test follow
follow. T Approximately
Approximately
Coin 1 paddle width eee adie
Setting 3 or 5 balls served 4, ROM 2: D 5.ROMB&2:E 6.ROM1&2:F
Game Time (11 or 15 points) Breakout D E F
Replay Level Approximately Approximately 1paddle width 2 paddle widths
7,ROMB,18&2:G
3 paddle widths
2 LED Switch Test
Press each button on
the control panel.
Trip right and left coin
switch wires.
Close contacts of coin
door slam switch, (See Figure 3-1 & Figure 3-7 in Chapter 3 of this manual for locations of coin switch wires and slam switch.) A low frequency electronic sound will occur each time a button is pressed. (The GAME SELECT and PLAYER START button lights will go off when pressed.) The coin lockout coil will click each time the. GAME SELECT button is pressed
or released. The same low frequency sound will occur each time a coin wire is tripped, and each time the slam switch contacts are closed and released. If either RAM is bad, the TV monitor wi
can be displayed. show ‘BD’ on the screen if it If RAM! (PIA at location E4/5) is bad, a HIGH PITCHED SOUND wi
occur. if RAM? (PIA at location C4/5) is bad, the screen might display:
“Garbage! No sound will occur. NOTE: Ifa button is stuck “on” (constant low frequency sound) check the GAME SELECT and START button lights. If they are on, Start a Volleyball game—FOUR-PLAYER. If none of the paddles are “jumped” (vertically displaced), the error is the slam or coin switch. No sound will indicate a stuck or broken switch, or an open or
shorted harness.
SSNCTATTTNTTANTNNNTNY
AVA AAVALAVALLA LLU LESTEATRERAARUAEEA 8-TOGGLE DIP SWITCH 4-TOGGLE DIP SWITCH
GAME PCB
Figure 1-4 Option Switches on Game PCB
Table 1-3 Operator Options
Four Plays Per Coin 8-Toggle DIP Switch on PCB} TV Monitor Toggle No. during
| Coin Mode/Game Cost Options | 1 | 2 | 3 | 4 | Self-Test |
| Two Coins Per Play—both Left* & Right* | ON | ON | ON | ON | A |
| One Coin Per Play—both Left & Right | OFF | ON | ON | ON | B |
| Two Plays Per Coin—both Left & Right | ON | OFF | ON | ON | Cc |
| Three Plays Per Coin—both Left & Right | OFF | OFF | ON | ON | D |
| First Coin—One Play; Second & extra coins— | ON | ON | OFF | ON | E |
Two Plays Per Coin First Coin—two Plays; Second & extra coins—
| Three Plays Per Coin | OFF | ON | OFF | Om | F |
| Left—Two Coins Per Play; Right—-One Coin Per Play | ON | OFF | OFF | ON | G |
| Left—One Coin Per Play; Right—Two Plays Per Coin | OFF | OFF | OFF | ON | H |
| Left—Two Plays Per Coin; Right—Four Plays Per Coin | ON | ON | ON | OFF | I |
Left —First Coin—One Play; Second & Extra Coins— Two Plays Per Coin
| Right —First Coin—Three Plays; Second & Extra Coins— | OFF | ON | ON. | OFF | J |
Table 1-3 Operator Options
8-Toggle DIP Switch on PCB] TV Monitor Toggle No. During
| Option | 1 | 2 | 3. | 4 | Self-Test |
Left—First Coin—Two Plays; Second & Extra Coins— Three Plays Per Coin
| Right—First Coin—Five Plays; Second & Extra Coins— | Ce | K |
Six Plays Per Coin Left—First Coin—Three Plays; Second & Extra Coins—
| Four Plays Per Coin | OFF | OFF | ON. | OFF | L |
Right—First Coin—Seven Plays; Second & Extra Coins— Eight Plays Per Coin
| Left—Three Coins Per Play. Right—One Coin Per Play | ON | ON | OFF | OFF | M |
| Left—One Coin Per Play. Right—Three Plays Per Coin | OFF | ON | OFF | OFF | N |
Left—First Coin—Three Plays; Second & Extra Coins— Three Plays Per Coin
| ON | OFF | OFF | OFF | Oo |
Right—First Coin—Six Plays; Second & Extra Coins— Six Plays Per Coin
| Four Plays Per Coin—both Left & Right | OFF | OFF | OFF | OFF | P |
Toggle No.
| Game Language (on TV screen) | 2 | & | 7 |
English ON ON
French OFF ON German ON OFF
Spanish OFF OFF
| Game Length 11 Points (in Breakout—3 balls served) | ON | an | 3 |
15 points (in Breakout—S balls served) OFF 15 5
Breakout Replay One full play granted after scoring required bonus level No Replay
Breakout Replay Levels OFF |A,B,C,D, or ON NO
4-Toggle DIP Switch on PCB Toggle No. 1 3
Replay granted for: 200 Points 250 Points 300 Points 400 Points 450 Points 200 Points
| OFF | OFF | ON | OFF |
| ON | ON | OFF | OFF |
| OFF | ON | OFF | OFF |
| ON | OFF | OFF | OFF |
| OFF | OFF | OFF | OFF |
Any other switch setting >moanw>
*NOTE: In this table, Left refers to the left coin mechanism, and Right refers to the right coin mechanism, when viewing the front of the game cabinet.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME PLAY
The game has three modes of operation: attract (power applied or after the end of a game), ready-toplay (coins accepted), and play (after any START button is activated).
A. ATTRACT MODE (See Figure 2-1) The attract mode begins when power is applied to the game and ends when the proper amount of coins clear the coin acceptor, or at the end of each game. The TV monitor displays the words GAME OVER and the name of the last game played. The score or scores of the previous game are displayed at the top of the screen. The words on the TV monitor appear in alternating white and grey video levels. Players have the opportunity to set any one of the twelve games with the GAME SELECT button. All controls (except GAME SELECT) and sounds are inactive during this mode.
—_I Typical TV Monitor Display During Attract Mode Figure 2-1
r
Figure 2-2 Typical TV Monitor Display During Ready- To-Play Mode
Figure 2-3 Typical TV Monitor Display During Play Mode
B. READY-TO-PLAY MODE (See Figure 2-2) When the correct amount of coins clear the coin acceptor, the ready-to-play mode is initiated. During this mode the number of credits is displayed on the left side of the screen and the name of the current game is shown on the right side of the TV monitor. Players have the opportunity to set any one of the twelve games with the GAME SELECT button. Each time the button is pressed to change a game, the name of the game changes on the TV monitor. The ready-to-play mode will also occur at the end of game play if there are credits remaining.
The OPTION CONTROL buttons on the control panel stay lit and the START buttons are lit according to the number of credits showing on the TV monitor.
To play any game one credit per player is required. Without at least four credits, the FOUR- PLAYER START button cannot be activated and so on for the other versions. During game play the GAME SELECT button is inoperable.
C. PLAY MODE (See Figure 2-3) The play mode begins when one of the START buttons is pressed. Pressing a START button removes the words from the screen and sets the playfield for the selected game.
Breakout In Breakout, a one- or two-player game is optional. A minimum of two credits is required for a two-player game. The controls on the far right of the panel (labeled BREAKOUT SINGLE PLAYER CON- TROL), are used for the one-player version. The two-player version uses the same controls along with those on the far left of the panel (labeled BREAK- OUT). The OPTION CONTROL button functions as a ball serve.
The object in Breakout is to obtain the highest score. A three- or five-ball game is optional and there is no time limit (see Chapter 1, Table 1-3). When all of the bricks have been hit, the playfield is refilled. There is no limit to the number of times the playfield can be refilled with bricks. When this occurs the ball count remains the same. However, when replay is in use, and a player scores the specified amount of points, one full play is granted. (One credit is given. No credit can be earned during a replay game.) Table 1-3 contains replay levels and the corresponding switch settings. No replay is also optional. The only time replay information is displayed on the screen is during the self-test mode (see Chapter 1, Table 1-2).
+
PLAYER THREE PLAYER FOUR
WHITE BLACK
CONTROLS CONTROLS
ayers CONTROL ‘AKOUT BRE! gincte PU
‘ONE PLAYER TWO PLAYER FOUR PLAYER ‘START STAR a )
PLAYER ONE @e ATARI” PLAYER TWO
‘OPTION
CONTROL,
Figure 2-4 Location of Player Controls
In a single-player game the ball count is displayed at the top left of the screen and the score is shown at the top right. The count changes each time the serve (OPTION CONTROL) button is pressed, unless there is a ball in play. In a two-player game the ball count and score locations are reversed for the second player. The difference in the two-player version is that the ball count stays on the screen only until the first contact between the ball and paddle. After initial contact the ball count disappears and the opposite players accumulated score appears on the screen,
The first two rows of bricks are worth three points each, the second two rows are worth five points each, and the last two rows are worth seven points each. The ball speed increases every fourth paddle contact up to the twelfth contact. Maximum speed is reached by hitting any brick in the last three rows. When a player “breaks out’’ by hitting a ball through the last row of bricks and contacts the back wall, the size of the paddle is cut in half for the remainder of the turn. Each new turn restores the paddle to its original size.
Soccer I A two- or four-player game may be selected. One credit per player is required to start either game. Ina two-player game, controls number one (white team) and two (black team) are used. See Figure 2-4 for location of player controls. In a four-player game all four sets of controls are used. Controls one and three
operate the white team, controls two and four operate the black team. The kickers (paddles) move together in vertical unison on the screen. Each player controls two kickers, whether in a two- or four-player game. In a four-player game, controls three and four operate the striped kickers.
The object in Soccer | is to be the first team to kick 11 or 15 goals, depending on which game end score is selected. See Table 1-3 (Chapter 1) for operator options and the corresponding switch settings. Each goal is worth one point. After a goal is scored, the ball is automatically put into play against the team which did not score. The white team score is always on the top left of the screen, the black team score is always on the top right. In Soccer I, players may use the WHAMMY feature which is described in detail in Chapter 1. A time limit of ten minutes is programmed into the game.
Soccer IT Soccer II is a four-player game. Four credits are needed to start the game. Each player controls one kicker. Controls one and three operate the white team and controls two and four operate the black team (see Figure 2-4 for location of player controls). Players may use the CATCH feature which is described in Chapter 1. Refer to the game play description for Soccer |, which is identical for all other details.
Foozpong Foozpong is programmed as a two- or fourplayer game. One credit per player is required to start either game. The CATCH option/feature (see Chapter
- isavailable to players in this game. The object of the game is to score 11 or 15 goals (see Table 1-3, Operator Options) or to have the highest score after the ten-minute time limit. Each goal is worth one point.
In two-player Foozpong, player one (see Figure 2-4 for player locations), controls two white rows of paddles and player two controls two black rows of paddles. In a four-player game, player one controls two white rows of paddles, player two controls two black rows of paddles, player three controls two striped rows of white paddles, and player four controls two striped rows of black paddles.
Each row of paddles moves vertically on the screen in unison; however this movement is restricted. Each paddle can move across half the playfield. There are four paddles in each row, but only three paddles appear on the screen at one time. After a goal is scored, the ball is automatically put into play against the team which did not score. The white team score is always on the top left of the screen; the black team score is always on the top right of the screen.
Hockey I Programmed as a two- or four-player game, Hockey | requires one credit per player to start the action. The WHAMMY feature, described in Chapter 1, is available to players in this game. The object of the game is to score 11 or 15 goals (see Table 1-3, Operator Options) or to have the highest score after the ten minute time limit. Each goal is worth one point.
Players move the hockey sticks (paddles) vertically on the playfield screen with their controls. Ina two-player game, each player controls one stick. Player one controls the white hockey stick; player two controls the black stick. (See Figure 2-4 for location of player controls.) In four-player games, the players also control one hockey stick each. Players one and three control the white team; players two and four control the black team. Each team has a forward stick and a goalie stick, the latter being striped.
The hockey sticks can be moved vertically up and down the playfield from edge to edge. After a goal is scored the ball is automatically put into play against the team which did not score. The white team’s score is always on the top left of the screen; the black team’s score is always on the top right of the screen.
Hockey II Hockey II is a two- or four-player game and offers the CATCH feature (see Chapter 1). In the two-player version, each player controls two sticks—one forward stick, and one goalie stick. The sticks move simultaneously up and down the screen in a vertical path. Player one controls the white sticks and player two controls the black sticks. The four-player game includes a vertical line of three paddles for each player. Players one and three control the white paddies; players two and four control the black paddles. Figure 2-4 shows the location of player controls. See the game play description for Hockey | for all other details.
Hockey If This game is for two players only. Asin Hockey Il, the CATCH feature (see Chapter 1) is programmed into this game. Player one controls three solid white hockey sticks which move in unison; player two controls three solid black sticks which do the same. Fig-
ure 2-4 shows the location of player controls. Refer to the game play description for Hockey | for all other details.
Quadrapong™ Quadrapong gives players the opportunity to shoot at two different goals. Movement of each player’s paddle is restricted to one side of a rectangular playfield. Each side of the rectangle has a goal, and each paddle guards a goal. To score, players must hit the ball into either goal guarded by the opposing players. It is possible for players to hit balls into their own goals, thereby adding points to the opponent's score.
The object of the game is to score 11 or 15 points (see Table 1-3, Operator Options) or to have the highest score after the ten minute time limit. Each goal is worth one point. One credit per player is necessary to start a game.
In two-player Quadrapong, player one controls the white paddles; player two controls the black paddles. In a four-player game, players one and three control the white paddles; players two and four control the black paddles. (See Figure 2-4 for location of player controls.) In both versions, the horizontal paddles are larger and solid; the vertical paddles are slightly smaller and striped.
After a goal is scored, the ball is automatically put into play against the team which did not score. The white team score is always on the top left of the screen; the black team score is always on the top right of the screen. There is no option feature for Quadrapong.
Handball This game is played almost the same as a regular game of handball. A two- or four-player game is optional. In either case players control one paddle each. One credit per player is required to start the action. To win, a player or players must score 11 or 15 points, or have the highest score after the ten minute time limit. See Table 1-3 for operator options and the corresponding switch settings.
All paddles are located on the same side of the playfield. To score, a player must “pass” the other player’s paddle. Each time this is accomplished, a player scores one point. The WHAMMY feature is part of the handball action in this game. See the description in Chapter 1 for details on this option feature. In a two-player game, player one controls the white paddle; player two controls the black paddle. (See Figure 2-4 for location of player controls.) When a paddle is solid, it is that player’s turn to hit the ball. After the ball is hit, the paddle will blink. If the ball is hit out of turn (when the paddle is blinking), the opponent scores one point.
In a four-player game, players one and three control the white team; players two and four control the black team. Paddles three and four are striped. The tactics are the same, except that two players are added to the game. Both paddles on one team will blink when it is the other team’s turn to hit the ball.
Players move their paddles vertically up and down the playfield. It is possible to make the paddle disappear from the playfield by going beyond the edge or wall. After a goal is scored, the ball is automatically put into play against the team which did not score. The white team score is always on the top left of the screen; the black team score is always on the top right of the screen.
Volleyball Two or four players can compete in this game. The object is to return the ball over the net which is located at the bottom center of the playfield. To win, a player or players must score 11 or 15 points, or have the highest score after the ten minute time limit. Table 1-3 in Chapter 1 contains information on operator options and the corresponding switch settings.
The paddles move in a horizontal line at the bottom of the playfield. A player or team scores one point when the opponent misses the ball or hits it into the net. In a four-player game, the second player on each team will cover the upper portion of the playfield with a smaller paddle. See Chapter 1 for a description of the JUMP feature, which is programmed into the Volleyball game.
In a two-player game, player one controls the white paddle; player two controls the black paddle. (Figure 2-4 shows the location of player controls.) Ina four-player game, players one and three control the white team; players two and four control the black team. After a goal is scored the ball is automatically put into play against the team which did not score. The white team score is always on the top left of the screen; the black team score is always on the top right of the screen.
Basketball I This game has a two- or four-player version. As in all Tournament Table games, one credit per player is necessary to start the action. Each player controls one paddle that moves in a horizontal line across half of the playfield bottom. Each player or team has a basket. The player or team on the left side of the
- playfield shoots at the right basket, and the player or team on the right side of the playfield shoots at the left basket. One point is awarded for each basket scored. To win, a player or team must score 11 or 15 points, or have the highest score after the ten minute time limit. See Table 1-3 for information on operator options.
Where the ball is dribbled on the paddle determines the direction in which it will travel. If the ball is dribbled off the right side of the paddle, the ball will shoot to the right. When the ball is caught between the bottom of the playfield and one of the paddles, the ball will eventually bounce through the paddle.
A player or team scores one point when the ball goes through the basket. In a four-player game, the second player controls the smaller paddle located higher on the playfield. See Chapter 1 for a description of the JUMP feature, which is programmed into this game.
Ina two-player game, player one controls the white paddle; player two controls the black paddle. (Figure 2-4 shows the location of player controls.) In a fourplayer game, players one and three control the white team; players two and four control the black team. After a goal is scored the ball is automatically put into play against the team which did not score. The white team’s score is always on the top left of the screen; the black team’s score is always on the top right of the screen. Itis possible to score points for the opponent player or team by shooting into the wrong basket.
Basketball II See game play description for Basketball |. The only difference between the two games is that Basketball II offers the CATCH feature, which is described in Chapter 1.
GENERAL NOTE The game sounds for the various Tournament Table games range from low- to high-pitched electronic noises. Each game function or action has a distinct electronic sound.
Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.
If you are interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator's Handbook, manual number TM-043. This book is available from Atari, Inc., Attn. Customer Service Department, 2175 Martin Avenue, Santa Clara, CA 95050 for $5 each, or from your distributor.
ADJUSTMENTS
A. CLEANING The exteriors of game cabinets and plex panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the plex panels because any dust can scratch the surface and result in fogging the plastic.
B. COIN MECHANISM Components On Coin Door Figure 3-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. But during the ready-to-play mode when the LED is lit, and during the play mode (and also when AC power to the game has been turned off),the lock-out coil is de-energized, causing the lock-out wires to move out far enough to divert coins over to the return chute. Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.
Also shown in the photograph is a slam switch assembly. It has been included to discourage any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down on arelease lever and simuitaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3.
Slam Switch Assembly
Coin Lock-out Coil
Coin Door Assembly Lamp holder
Figure 3-1 Figure 3-2 Hinging Open the Magnet Gate Assembly
Figure 3-3 Removal of Coin Mechanism
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air. Figure 3-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of
(Clean both surfaces where coin enters the mechanism, as well as the magnet) Figure 3-4 Surfaces to Clean Inside the Coin Mechanism the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.
If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 3-5). Removing the plate will provide access to the entire channel.
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Figure 3-5 Removal of Plate Covering Rear of Coin Slot
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 3-6 shows this lubrication point.
Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 3-7. Use extreme care when handling or touching these wires.
Manually hold down rejection button and apply one drop here
Lock-out Wire
Figure 3-6 Close-Up View of Lubrication Point
Three problems can occur with trip wires—they can be too long, too short, or become loosened and fall off.
Correctly adjusted trip wire
Figure 3-7 Detail View of Coin Switch and Trip Wire CRIMP TOGETHER MOUNTING STUD AT 2 ARROWS SHOWN
Figure 3-8 Securing the Coin Switch Trip Wire
With a wire that is too long, you may have a problem of it catching on the opening in the cash box as a coin is accepted. You can cut off the end of the wire in small increments, making sure it still extends slightly through the “’V’”’ of the coin chute.
If the trip wire is too short (either by wrong adjustment or by being cut off too much), coins may slip by the wire without tripping it, and no credits will be given. The solution is to carefully bend and straighten out the wire to lengthen it. If you cannot straighten it sufficiently, contact your distributor to order another trip wire.
If the wire is loose and falls off its mounting stud, it will also cause no credits to be given. Secure the wire by crimping-together both ends of the brasscolored mounting stud with a pair of pliers (see Figure 3-8). If you should ever need to remove the trip wire, the two halves of the mounting stud can be separated with a small screwdriver.
Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure3-9shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These
ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly 8 “C” washer 9 Rail 10 Gate Assembly 12 Cradle Assembly
13 Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magi Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Coin Release Lever Kicker and separator
- Set the acceptor with the back of the unit facing you in the test position.
- Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
- Insert several test coins (both old and new) and note that some are returned by striking the separator.
- Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
- Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
- Insert the test coins and note that some are returned.
- Loosen the kicker screw and move the kicker a slight amount fo the right. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted,
- Be sure that both screws are tight after the adjustments have been made.
Magnet gate
- Set the acceptor with the front of the unit facing you in the test position.
- Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
- With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate. 4, Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted. 5, Fix the magnet gate adjusting screw in this position with a drop of glue.
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- Replace the transfer cradle and the undersize lever.
- To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.
Figure 3-9 — Adjustments on Coin Mechanism
adjustments should only be done by someone who has experience in servicing coin mechanisms and who understands their operation.
General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
C. FUSE REPLACEMENT
Tournament Table contains five fuses, three on the power supply assembly and two on the TV monitor assembly. All fuses are easily accessible through the rear door assembly. Replace fuses only with the same type of fuse as follows: TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick-blow, 250 volts Power Supply: Fuses F1 and F2—3AG 3-amp slow-blow, 250 volts Fuse F5—3AG 8-amp fast-blow, 125 volts
D. TV MONITOR ADJUSTMENTS
The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustment.
The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 3-10 shows the location of the adjustments on both TV monitors used by Atari. Your
TEC MODEL TM- 600/623 eowrnast \~\\"Cvear. Cent tn 2 FUSES REMOVE” conrnast BRIGHTNESS : Gover ‘To RESLACE : Loinnayl HEIGHT (both 0.8 A quick blow) BppizsOeG: — woriz, novo) \_verr Ho. VOLTAGE SWITCH \eave In right poston)
MOTOROLA MODEL M5000/M7000
Figure 3-10 Locations of Adjustments on TV Chassis
SUPPORT BAR
WING NUTS (2) CARRIAGE BOLTS (4)
Figure 3-11 TV Monitor Removal
game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC. When making adjustments, follow these general guidelines: BRITE (Brightness)—Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up. CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred. HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warpea, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture. VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture. E. TV MONITOR REMOVAL (See Figure 3-11) Unlock and remove the rear door assembly. Reach in through the back of the cabinet and remove the two wing nuts securing the control panel (top assembly) to the cabinet bottom assembly. The top assembly of the cabinet may now be lifted upward starting from the back of the cabinet. Although the top assembly is balanced to remain in a raised position, the support bar should be used for safety while working inside the cabinet. Next remove the four carriage bolts that secure the monitor to the TV shelf assembly. Disconnect the TV monitor harness and slide the monitor out through the top of the cabinet. As you slide the monitor out of the cabinet, be certain that the cabinet does not become unbalanced.
F. LED SWITCH AND ROTARY SWITCH REPLACEMENT (See Figure 3-12) The LED switches (PLAYER START, GAME SELECT, AND OPTION CONTROL), are accessible for servicing when the cabinet top assembly is raised. Use the following procedure:
- Unlock and remove the rear door assembly.
- Reach in through the back of the cabinet and remove the two wing nuts securing the control panel {top assembly) to the cabinet bottom assembly. LED
POTENTIOMETER Ps OF
Figure 3-12 LED Switch and Potentiometer Replacement
- Starting from the back of the cabinet, raise the top assembly. The support bar should be used for safety while working inside the cabinet (see Figure 3-11).
- Remove all wires from the suspected switch.
- Turn the switch counterclockwise while holding the cone-shaped nut on the outside of the game cabinet.
- Install a new switch using the reverse procedure.
- Reconnect the harness wires.
The potentiometers are also accessible for servicing when the cabinet top assembly is raised. After following Steps 1 through 3 above, use the following procedure:
- Remove all wires from the suspected switch.
- Remove the knob and hex nut on the control panel.
- Install a new switch using the reverse procedure,
- Reconnect the harness wires.
OPERATION
A. GENERAL INFORMATION The PCB block diagram in Figure 4-1 shows the major controls, circuits and outputs of the game. Figure 4-2 is a block diagram of the Tournament Table game.
The game's television monitor is a self-contained transistorized unit. The composite video signal sent to the monitor differs in many respects from the signal derived from commercial TV broadcasts. The picture appearing on the screen, therefore, is unlike that of a home TV set and the monitor does not produce any sound. See Chapter 6 for a schematic diagram of the TV monitor.
MONITOR INTERFACE ADAPTER VIDEO OUTPUT
AUDIO AMPLIFIER
PERIPHERAL INTERFACE ADAPTER (PIA)
PROGRAM MEMORY (ROM) OPTION SWITCHES
DRIVERS TO TV MONITOR
TO SPEAKER
PLAYER POTS
CONTROL BUTTONS
LEDS
Figure 4-1 Tournament Table PCB Block Diagram
HORIZONTAL DEFLECTION
Ww MONITOR cIRCUITRY
VERTICAL, DEFLECTION
CONPOSITE ‘ONE PLAYER MaDEO START
TWO PLAYER
PLAYER ONE ‘OPTION CONTROL
GAME PRINTED cIRcUTT BOARD SPEAKER,
[PLAYER THREE] ‘OPTION CONTROL
‘OPTION PLAYER ONE CONTROL POTENTIO-
PLAYER TWO POTENTIO- METER
VOLUME CONTROL
SELF-TEST SwiTcH
Figure 4-2 Game Block Diagram
The game’s composite video signal produces only four video levels instead of the continuous shades of grey seen on a home TV screen. The video levels are light grey, grey, white, and black.
On the game PCB schematic diagram, the symbol “P” (appearing at various inputs of integrated circuit devices) indicates a connection of +5 volts DC through a pullup resistor (see Figure 4-3). For easy reference, the game PCBis divided into grid sections. Along the short side of the board, these sections are identified by letters A through E. Along the long side of the board, the numbers 1 through 9 are used. For example, sheet 2 of Figure 4-3 illustrates the microporcessor £3 at the right side of the drawing. The microporcessor is found at coordinates E and3 on the PCB.
A monitor interface adapter, which is controlled by the microprocessing unit (MPU), performs the following functions:
- Produces all horizontal and vertical sync functions.
- Generates video for all objects. © Generates all sound.
The MPU reads player pots through this adapter by measuring the charge rate of a capacitor charging through each pot.
Input interface adapters read switches (option, player control, and start switches); and function as outputs jor the LED control, and the coin lockout control.
B. POWER SUPPLIES (Bottom Right of Schematic Sheet 1, Figure 4-3) Two voltages are used on the Tournament Table PCB: voltage-regulated +5 volts DC and unregulated +10 volts DC. The voltage regulated +5 volts DC provides Vcc for most of the PCB’s integrated circuits. Unregulated + 10volts DC provides V+ for theLM 380 audio amplifier.
C. CRYSTAL OSSCILLATOR AND TV SYNC COUNTDOWN CHAINS
A 3.57 MHz crystal oscillator generates the basic clock frequency that is divided down by the monitor interface adapter to produce TV synchronization signals. The signals are used to produce the TV monitor raster, consisting of horizontal lines at a horizontal frequency of 15.7 KHz. D. MICROCOMPUTER The microcomputer is the control center for the circuitry that makes up the game action. The microprocessing unit (MPU) sends out addresses on its address bus and accepts from, or outputs data onto the data bus. The Address Decoder receives the address, translates the address code, and enables the circuitry called by the MPU. When the MPUis reset by receiving a low, and then a high on its RESET line, its outputs address the program memory to put data onto the data bus. The MPU reads this data and uses it to address the main program.
The main program instructs the MPU to execute operations, and instructs at which address to execute them. This controls the flow of data on the bus and “reads’ inputs and ‘writes’ to outputs. Data may flow into the MPU from program memory, randomaccess memory (RAM), or from tri-state drivers from the input and option switches. Data may flow out of the MPU to the RAM, to the peripheral interface adapter, or to the monitor interface adapter.
E. MICROCOMPUTER WATCHDOG
The watchdog circuit is connected to the RES input of the MPU. This circuit prevents the microcomputer from going into a program loop.When the MPU is functioning properly it will periodically pulse the “TIMER RESET” line. This tells the watchdog (B7, D8) that the MPUis okay, so that no action is taken by the watchdog.
If the MPU fails,the “TIMER RESET” line is not pulsed. The watchdog then is not told that the MPU is okay. The watchdog then restarts the program by forcing the RESET low, then high.(If successive TIMER RESET pulses do not occur within 80 ms, the program will restart.
When the microcomputer is functioning properly, the watchdog will not reset the MPU.
F. VIDEO OUTPUT (Lower Right of Schematic Sheet 2)
The video output circuitry receives both the playfield and motion information, selects the proper grey scale shading, and sums the signals with blanking signals. The circuitry then provides a composite video output.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING SEE CHART CONFIDENTIAL. Reproduction forbidden without the
| +5N | av | +5 | Eaton’ This drawing ony conllonaiy sued and |
‘either receipt not possession thereol coniers or transfers ry right in oF heense 40 Use. the subject matter of Ine arming ot any design or techmeal information shown
| tee | 26 | [at | 24 | jai | tnoresh excep for manufacture py vendors oa Theor |
Porated and for manufacture uncer the corporation 8 wit fenticerse noright to reproduce his drawings granled ot
| Alaz | A/B3 | AIR 4 | the subject matier tereot uniess by wrtlen agreement |
uth or mitten permission from the corporation
| Agia | 28 | AY |
| ABQ | 32 | Aa |
| Age | ; | AB |
| aB7 | ‘ | al |
ABG he
| ABS | 3 | AS |
AB4 A
| ABs | 3 | a3 |
| AB2 | £ | A2 |
| ABI | 3 | al |
ABD Ad
| » | —2 | 7 |
| De | —8 | Joe |
| 8 | ral | ki |
| D4 | 13] | 04 |
| bs | —8 | 3 |
02 oz
| o, | — | a |
| pé | ——4} | 08 |
oH tsa | GI wr | SS ci
| a6 | fiz | ie | 20 ]i2 | jie | [20 ]2 | JI |
¢
Rams: 1D—-+4 +5V
| Rom | + | 4) | =| |
SbF alelele Roma *—aD 390 x4 PLES € 3 m7 1 con? ARIZ B ry ROM 1
aBll 13
+5V +su +R
Re 470 CRI INdt4
ce
’
2N390 az ose xt
3.579575 MHZ RS too
SEE CHART
| —_—_--— | LoeNERS)-O1 | -02 | -O3 | -04 | ||
| +5 | 45V | AlB2 | |O307S1 | — | 93075) | [030751 |
| Alga | [oso7sz[o307se[ | — | | o30752 | ||
| 8 | 18 | Aia4_ | 030753|030753[030753| | — | ||
| AS | as | AS | = | 030754|03075 {030758 | |
| 826185 | 625185 | 8s | - | (030755 | 030757030759 | |
| asia | —8 | ab | |||
| ago | —é | aq | NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. |
age —e1______jaa CONFIDENTIAL Reproduction forbidden without the
| ner" | ~ | ar | spose writen gernnsion ef a ine "Sunnyate |
failorna. This Growing 1s only conciionally issued. an
| ave | — | Ab | Rertherracetpi nor possession thereat confer o transfers | |
| ABS | AS | ny rant mor iconse to use, Ine subject matter of the | ||
| ABS | a | AS | raving oF any design ot technical ormation shown | |
| A | ig | theteot except for manatcture by vendors of Aor incor | ||
| Aaa | Az | porated and for manufacture under the corporation's wit: | ||
| . | ABl | 4 | Al | tenlicense nerighttoreproduce this drawings granted or |
the subject matter thereat unless by written agreement
| Aso | ag | wn or writen permission Vom the corportion |
| p7—o4 | oa} | 3 |
| bb—i2 03 | 03/2 | p2 |
i bs —{3/ 02 02/38
| p4—FTor | ot | bd |
a ce 10 9 o
i
45V Rl PLAYER pe Cc) ves | se {p] +sv (Wed) rc (Pot) FIOV UNREG sh l
| T cae | tL | ose | Be saa |
22 2at, 25v BYPASS 5 Nss (GND)
eND
Figure 4-3 Tournament Table PCB Schematic Diagram Sheet 1 of 2
—+— +5 osu
RT Rie 120
- 1%
com sw g— ———8 pe» ‘suam Le ot 2} poe
lea + Bre, cays Game sevect [oh st Gs Ten JT esviAe pe czo Ve TIMER RESET. ABe jase, ABS laos asa Slane
| = | aga | ——S/a03 |
ag2 —Slasz Ast Ast Aso ——Yase
ea7 Paw pas pad Pas paz Pal Pad vss
[sw
| = | [swires | a | came |
sevect leo +8 3] com Cockout ‘i Rso Wee oF *1> 2s 8044
P87 WS Pee Tea [2 es Pee Pes Pez P51 rob e4/s 1 co 16750
| Rag | e3PL | BB | Bao | oer 2 py | ||
| 1% | Abe —*} nae | ae tet — bo | ||||
| RZ | ABs | 4) nes | bas}28 | 95 | ||
| con sw | [AP | i | +5¥ | 484 ——3] nag | peal 22 | pg |
| a | - | nes | 2] | 30 | ||
| be | Mest switen (51106), | - | ane | bes] Sr 03 |
Tle met —4l Aer Ey T! staat sui [3] start swe [0] START SN +5v xs oe rt
w le
| Aee | aad | oad 33— | o@ | Ris | ais |
1.8K a xa Pics,
FAD Hl ome, ad + + it Pas
| f | I. | 13) | oz |
i
| - | iN | tl pad | 12 |
Sie eNe
toe Dl ae E
NOTICE TO ALi PERSONS RECEIVING THIS ORAWING CONFIDENTIAL. Reproduction forbidden without the Specific written permission of Atari, Inc.. Sunnywar, Caiforaia This drawing '6 only consitionally issued. and neither receipt nor possession thereat confers or leansters any right in. or license 10 use. the subject matter of the drawing of any design 01 technical information shown thereon, narany right to reproduce this drawingor any part thereot, except for manulaclure by venders of Alar Incorporated and for manulacture under the corporation's we fen license. mo righ to reproduce this drawing s granted or lhe subject matter thereof unless by written agreement saith or Written permission fram the Corporation.
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL. Reproduction forbidden without the specific wrilten permission of Atan, Inc. Sunnyvale California This srawing 1s ony conditionally issued. and neither receipt nor possessien Ihereo! confers or transters any right in. oF license to use. the subject malter of the drawing or any design or technical imformation shown invonnaany rao waradgethdrawingranyar threo! excep! Yor manulacture by vendors ot Alar! nor porated and for manufacture unger the corporation 3 wt fenliconse.norighttorepraduce this drawing s granted or the subject matter therea! uniess by wntten agreement ‘with or written permission trom the corporation sar2—2I ane melt aBit Asia Baie A 23 439 nee £3, ABS B) age 6010745 my
| AB? | aay | bar |
ABe —\) abe Le a
| ABS | 12) ABs. | DBS | ||
| ABS | 3] aga | as] | ||
| 33 | ABs | e9| | ||
| ABZ | 2) ape | 082 | ||
| ABL | te! nat | bees | ||
| . | ‘aed | ase | oed| | Do |
ayw 26 aw
| . | 33h | #2 |
Rov |
ves
La a8
HH tov unre 20 ng, 25 Vee = cat asv 2 csi poy 2 oe
| exe | —24| ca | iw [25 — nsw | Rar | |||
| ABID | 2 Se | 92 | 22 | ga | baal | 643 |
| aay | —*4c33 | Rae | {Hid Avdio OUT | |||
| aur | + | Oat |
ang aK cas conde |g . 07 34— 07 come Vine 33 ay De De
| nes | —Hlas | os ['8@— | bs | |
| ase | 2) ae | pa [2 | be | — |
| ABs | a | os[2— | 93, | |
| pez | —21 ne | pale — ba | wb abe | TW seux |
| AB! | NY | D | di | 88 88 58 88-89 5 5x |
| nog | 2a Ab | Dele pe | Be ES BS ES ES 33K | | Meum |
‘ PA Le eux {e G eum?
| cout? | i | i | ‘s | |
| Sirs | orale | 3 | 2 | La aime |
| —_—__— | Mi | + | cd | |
| 13 | cma} | 2 48S | {5 BSN | |
| 35) t? | a | ashe |
aie ve |2
| * | ose}! | osc |
vss
Figure 4-3 Tournament Table PCB Schematic Diagram Sheet 2 of 2
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ILLUSTRATED PARTS CATALOG
The purpose of this Chapter is to provide you with the necessary information for ordering replacement parts for the Tournament Table Game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this list, and the serial number of your Sky Raider game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
If there are any questions about this list, please contact Atari’s Customer Service Department by telephone Monday through Friday, from 7:30 a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900, from the remaining 47 states call (800) 538-6892 toll-free.
NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Aeprosuction forbidden without the Specific writen permission of Atari. Inc. Sunnyvale. California. This drawing 1s only conditionally issued. and nether receipt nor possession thereo! conters or transters any right in. oF license to use. the subject matter of the drawing or any design or technical information shown Ihereen. aoc any right to reproduce thus drawing or any part Inereol. excep! for manufacture by venars of Atari incor porated and for manulacture under the corporation’ wt- Teslicense, no righl to reproduce this drawing'sqranted ot the subject matter thereo! unless by written agreement with or written permission trom ine corporation.
6 RED'D
- THE FOLLOWING ITEM NUMBERS ARE NOT
SHOWN: 17, [8 20, 2,24
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction torbdiden without Ine specitie written sion of Atan, Inc, Sunnyvale. California. This drawing Is only corditionaly issued. ang either receipt nor possession thereof confers or iranslers any right in. oF license to use the subject malter af the ‘érawing or any design or tectnical information shown thereon, nor any ight to reproduce this drawing or any part teraot. except for manutacture by vendors of Att! Incorporated and for manufacture under the corporation's wri fen license, na right to reproduce this drawing s granted or the subject malter thereat unless by written agreement with oF watten permission from tne corporation
seca \
1§ 2 ; 3 REQDT) 28) 4 REQD
i @) \ 8 4 REQD © ' ©
2 REQD
2 REDD QL Figure 5-1 Tournament Table Final Assembly 4 REC'D (26) A030726-01 A
Figure 5-1 Tournament Table Final Assembly Parts List
ATARI
Item Part Number Description
| 1 | A030714-01 | 1 | Assy Cabinet, Bottom & Top |
| 2 | A030715-01 | 1 | Assy., T. Shelf - See Figure 5-2 |
| 3 | A030716-01 | 1 | Assy., Plex, Top/Control Panel- See Figure 5-3 |
| 4 | A030170-01 | 1 | Tournament Table PCB Assy- See Figure 5-4 |
| 5 | A030709-02 | 1 | Assy., Door W/Lock |
| 6 | A006794-xx | 1 | Coin Door Assy - See Figure 5-5 |
| 7 | A007197-01 | 1 | Power Supply Assy Type B - See Figure 5-6 |
| 8 | A009548-01 | 1 | Assy., Coin Box Lid |
| 9 | 009549-01 | 1 | Coin Box |
| 10 | 030717-01 | 1 | Bracket (Coin Box) |
| ll | 030733-01 | L | Bezel W/Graphics |
| 12 | 030722-01 | i | Support Bar |
| 13 | 002728-01 | 2 24 Bracket, Panel Mtg. | |
| 14 | A030729-01 | BE | Main Harness |
| 15 | A030819-01 | 1 | Interlock Switch & Harness |
| 16 | A007784-01 | 1 | Strain Relief Power Cord Assy |
| 17 | 005233-01 | 1 | Rear Door Seal |
| 18 | 006305-01 | 1 | Printed Poly Bag |
| 19 | TM-113 | 1 | Tech Manual & IPC |
| 20 | 030734-01 | i | Patent Drawing |
| 21 | ST-113 | 1 | Self Test Procedure Chart |
| 22 | 46-2023002 | 2 | Fuse 3 AMP (Slow Blow) |
| 23 | 48-009 | an | Speaker 8" |
| 24 | 030728-01 | 1 | Harness Schematic - See Figure 5-7 |
| 26 | 72-68125 | 1 | Screw SM Ph Phil. #8 x 3/4" Lg |
| 27 | 72-6610 | 18 | Screw SM Ph Phil. #6 x 5/8" Lg |
| 28 | 72-68203 | 8 | Screw SM Ph Phil. #8 x 1.25 Lg |
| 29 | 75-5516B | 4 | Carriage Bolt 4-20 x 1.00" Lg Blk |
| 30 | 75-0158 | 4 | Washer Flat, % |
| 31 | 75-990505S | 4 | Nut, Lock Shallow Pat. Nylon 4-20 |
| 32 | 75-99090006 | 6 | Well Nut, Blind Hole Fastener |
| 33 | 82-8016 | 6 | Screw, But., Hd., Socket #10-32 x 1.00" Lg |
| 34 | 75-07021 | 6 | Washer, Flat, Black Nylon #10 |
© 4 warner Communications Company
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
PS eCAT ON OF DECAL MAY CHANGE AT THE TVOCRETION OF MANUFACTUEING.
Figure 5-2 TV Shelf Assembly A030715-01 A NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specilic written germission of Atari, Inc. Sunnyvale. California. This araming 1S only conditionally issued. and Dne'ther receipt nor possession thereat conters or transfers any fight in. oF license 10 use. the subject matter of the ‘drawing oF any design oF technical information shown thereon. ner any right to reproduce thie drawing ot anypart Inereot. excepl for manulacture by vendors of Alar incor porated and far manufacture under the corporation s wrtfen license. no righttoreprosuce this drawrng 1sqranted oF the subject malter thereat uniess by written agreement ‘with or written permission trom te corporation
A ATARI’ Figure 5-2 TV Shelf Assembly Parts List
Item Part Number Description
1 92-029 2 030708-01 3 006319-0 4 75-5120N 5 75-010S 6 75-040 7 75-9118
© 4 warmer Communications Company BRA RE EE 2 TEC (TM-600) 19" B/W Monitor Shelf, T.v. Copyright Decal 1978 Bolt, Carriage, #10-24 X 1.25 Lg. Washer, Flat #10 Washer, Split-Lock #10 Hex Nut, #10-24
@) 4 eeao
- 4 ego
Wo raver TOP MEW x \ ONE PLAYER Sm. r GAME SELECT Pou PLAYER. G / N\A]
ca)
oN PLAYERS NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction forsidden without the Specific witten permission of Alari, Inc. Sunnyvale. California. This drawing 1s only conditionally issued. and either receipt nor possession thereo! confers or irancters any night in. of license to use. the subject matter of the ‘drawing or any design oF technical information shown thereon. nar any right to reproduce this drawing or any part thereol_ except for manulacture by vendors of Ata Ine porated and for manufacture under ine corporation's writtenlicense.no nghttorepraduce this drawing s granted or the subject matter thereat uniese by written agreement with oF written permissien tram the corporation.
wv n
ONE Pave W/80 BOTTOM VIEW.
PLayeR® | +5V. CT H z | aie 2 c | Bciew 3 ze | ee 4 gf ee
J
| LAVER | NO. | NO. | NO. | NO. | |
| H | wR | Wen | RAV | BK | |||
| . | 2 | w/BN | WGN] | QW | BK | ||
| Figure 5-3 | Control Panel Assembly | 3 | W | WEN | RW] | BE |
| A030716-01 | B | 2 | a | wen] | ehw | Be |
Figure 5-3 Control Panel Assembly Parts List
ATARI
| Item | Part Number | Qty | Description |
| 1 | 030721-01 | 1 | Plex, Top Control Panel W/Graphics |
| 2 | 19-9036 | 4 | Allen Bradley Potentiometer (EJC1NO56F105UA) |
| 3 | 73-831 | 4 | Knob (Kurz-Kasch #1907-3BB) |
| 4 | 62-002 | 8 | Led Switch |
| 5 | 001856-03 | 8 | Alum. Bushing |
| 6 | 030724-01 | i | Main Grounding Plate |
| 7 | 030723-01 | 2. | Grounding Plate |
| 8 | 75-2608S | 3 | Screw, Mach., Round Hd. #6-32 X .50 Lg. |
| 9 | 75-046 | 3 | Washer, Split-Lock |
| 10 | 75-9268 | 3 | Nut, Mach., Hex, S.P. #6-32 |
| 11 | A030730-01 | 1 | Front Control Harness |
| 12 | A030731-01 | 2 | Side Control Harness |
tw) A Warner Communications Company
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIOENTIAL” Reproduction forbidden without the speeltic written permssion of Atari, Inc. Sunnyvale. California, This drawing is only cond tionally issued. and raitherreceipinar possession {nereot confers or Iransters any right m, oF license to Use, the Subject matter of the ‘drawing or my design or teehiieal information shows thereon. norany right to reprodure this drawing or any part Inereot, except for manufacture by vendors of Ata Incorporated and for manufacture under the corporation s writ: ten license.no eight to reproduce this rawingisqranted or the subject matier therec! unless by wrllen agreement ‘ain OF written permission Kom the eorraralion
ao a m a r Dad a 4 PaParas') Bilal aleia) 7% £8 1/8 a olelo 1} }/818 184 , 3ya/a/ 2 wu o[n|4 ° Sys) | SISTOigl ilo Parad PGS) | bed Pd ig ram 9/8/81 | 18] 9 Sim fat} sia Glala} [e New o/O o}o B18} L/8/ 8] ¢ algl ala] > lh aa
Figure 5-4 Tournament Table PCB Assembly A030170-01 A
Figure 5-4 Tournament Table PCB Assembly Parts List Ak -01 Version ATARI’ Item | PartNumber | Qty. Description 1 | 03027201 1 | Printed cireuit Board 2 | 10-8270 1 | Res, Carbon, 58, 4m, 27. OHM x4 3 | io-sio1 2]eos too * R13 4 | 10-5151 1 iso * R28 5 | lo-sza1 5 220 * R5, 34, 35,36,37 6 | 10-5391 4 380 * 28,9,10/11 7 | lo-sa7 3 a7 © 26,46, 50 @ | 10-s102 io i 212,15, 16,17, 30,38
39,40,41,47 9 | 10-sis2 1 1.5K 833 10 | 10-5182 5 tex 52,23, 24,25, 26 na | 10-5222 2 2loK 823,32 12 | 10-5332 5 3.3K R1e, 19,20, 21,22 13 | 10-5392 1 3.9K R31 14] lo-sa72 3 4.7K R7,13,14 15 | 10-5103 1 10K R45 1s | 10-5073 1 ame Raa 17 | 10-5154 2 150K RIT 1s | 10-5105 1 a R43 a9 | 10-5228 1 2.2m Rad | 20 | 10-5156 1 | Res, carbon, 58, kit, 15% R42 21 | 19-315103 1 | trimot, 5%, uw, 10K Ra9 22 | 21-tonio? 1 | cap, mylar, .ootse 28 23 | 21-101683 a fo” osgue €24,.25,26,27 2a] 2i-ao1a7a 1 lara o38 25 | 24-250105, 1 lu, 25v 38 26 | 24-250475 1 4.738, 25 37 217 | 24-250226 1 aout, 25v 36 28 | 24-250107 1 Loout, 25¥ a3 29 | 27-250102 2 | cap, cer disc .001ue, 25¥ roy 30 | 27-2010 2 "Tove," 25¥ c1,so ai | 27-25010a 30 | * True, "25 €3-8,11-23,29-34, 38]
41,429C9,10 a2 | 29-012 1 | cap, cer Hono. .22uf, 12¥y cae 33 | 31-amioo 2 | diode, 1mi00 cr2.4 34] 31-N914 2 |" anote cr1,3 35 | 35-2N3906 2 | transistor, 283906 roe) 36 | 34-2naiza 1 wo" naz 93 a7 | 37-4050 1 | ime. cet. 4050 36 3e | _37-74c02 2} " " tacoa 37,08 © Biere Commons
's Company
39. 55, 37-7416 37-7456, 37-1M323, 37-1380, 62-001 66-1147 66-118P1T 69-004 72-1608C 75-016 75-056 75-916 78-06001, 78-16005 19742728 79-42740 c010177-1 010744 010745 010750 030929 030752 030753 10-5560 34-2N6044 Part_Number
DESCRIPTION INT. CK. 7416 wo" 74156 Regulator 44323 OP-AMPLM380 Switch, MoM, SPST Switch, SPST, x4, DIP wo 8 xa, DIP Switch, SPDT, SLIDE Screw, Pan Ha, Phil, #6-32 x & Lg, Cres Washer, Plat, #6 Washer, Lock, INT, 46 Wut, Hex, #6-32, CRES Heatsink (2M323) Sitpad (L323) Socket, 28 PIN, Low Insertion Socket, 40 PIN, Low Insertion crystal, 3.579575 maz custom 1¢ (TIA) Ic (6507 ) IC (PTA 6532) Play 12 Program Rom 0 Play 12 Program Rom 1 Play 12 Program Rom 2 Res, Carbon, 5%, 1/4W, 56 Ohm RSL ‘Transistor, 2N6044
ET a/BL sua sw Swi sw2 2/3 B3 64/5 ,B4/5 3/82 a/B3 a/B4 Co
Tournament Table PCB Assembly Parts List
Part Number, DESCRIPTION. 39 | 37-7416 a || unr. cer. 7416 57 40 | 37-7a156 1 +s” pais R/BL a1 | 37-1323 1 |) Regutator 1¥323 42 | 37-360 1 || op-ame — na3e0 Bo 6 -02 Version 43 | 62-002 1 |] switch, mou, spst sea
44 | 66-s1apyr 1 |) switch, sest, x4, ore S03, 46 | 69-004 1 || swicch, sepr, sive sw2 47 | 72-1608¢ 2 || Screw, Pan Hd, Phil, #6-32 x 4 Lg, CRES 4s | 75-016 2 || washer, Flat,’ #6 43 | 75-056 2 || Washer, tock, rwr, #6 50 ‘75-916 2 Nut, Hex, #6-32, CRES 51 | 78-o6002 1 |} Heatsink’ «1m323) 52 | 78-16005 1 |} Sitpaa (um2ay Item | Part Number | Qty. Deseription 53 | 79-4278 1 || Socket, 28 Pin, Low Insertion
54 79-4270 3 Socket, 40 Pin, Low Insertion l 030171-02 1 | Printed Circuit Board 55 | conoi77-1 1 |] crystal, 2.579575 wiz 2 10-5 270 1 | Res, carbon, 58, 4, 27 onM R4 s6 | colo7sa 1 |) custon Le (rray cus 3 10-5103 2 . . 100 RL,3 57 { co10745 1 Te (6507 ) E3 4 19-5151 1 "8 150 R28 se | co10750 2 Ic (PIA6532) S4f$ B4/S 5 10-5221 5 = 220 5,34, 35, 36,37 59 | 030752 1 |] Play 12 Brogram Rom 2 5/83 7 10-5551 i * ” oo 8 ba orio ft so | 030752 1 || Ftay 12 Program RoW 2 a/Bd 5 Spear Py : aD © R646, 50 61} 030754 1 |} Play 12 Progeam PROM 0 AS 8 10-5102 lo Ce, R12, 15, 16,17, 30,38 62 | 930755 1 Play 12 Program PROM 0 BS
39,49,41,47 63 ° 10-5152 i " 1.sk R33 64 10-5560 1 Res, Carbon, 5%, 1/4W,56 Ohm R5t ro | 10-s1s2 5 18K R2, 23, 24,25,26 65 | s4-2Noo4e 1 || Transistor, 2NGo4g ee a | 10-5222 2," * 2.2K R29, 32 a2 | 10-5332 s | ° 3.3K R18, 19,20, 21,22 13 | 10-s392 ais * 8 3loK R31, 14 | lo-sa72 + " . aK R7,13,14 is | 10-5103 ajo "9 10K R45 6 | 10-5473 2 so" 47K Raa 17 | 10-sis4 1 so" 150K. R27 18 10-5105 L " "lM ‘R43 19 10-5225, afro "8 Dla Rad 20 10-5156 1 Res, Carbon, 5%, di, 154 ‘R42 21 | 19-315103, 1 | Trimpot, 58, 4%, LOK R49 22 21-101102 L Cap, Mylar, .00luf c2e
- 21-101683 4 [or 8 ossae €24,25,26,27 24 21-101474 L ial a +47ut C35 25 | 24-250195 1 | cap, Elec. lur, 25v 38 26 24-250475 L " 4.Juf, 25v C37 27| 2a-250226 1|« 22uf, 25v 36 28 | 24-250107 ais Lous, 25v a3 29 | 27-250102 1 | cap, cer vise -o01uf, 25v 2 30 | 27-250103 244 " lluf, 250 cl, 40 ai | 27-250104 30 ius," 25v 63-8, 11-23,28-34, 39]
41,42, C9,10 32 | 29-012 1 | cap, cer Mono. .22uf, 12v, caa 33 | 31-4w100 2 | diode, 2w100 cR2,4 34] 31-1N914 2 "woe oRt,3 35 | 33-2n3906 2 | Transistor, 2n3906 1.2 36 | 34-2Na124 1 . 2naiza 03 37 | 27-4050 1 | me. cee. 4050 a6 38 | 37-7aco2 2 |" "1402 37 ,D8
Figure 5-4 Tournament Table PCB Assembly Parts List
iten | Part Number ex. DESCRIPTION a9 | 37-7416 1 {| ar. cer. 7416 27 ao | 37-7a156 i “" 7ars6 ayBL a1 | 37-1923 1 |) regulator 11323 . a2 | 37-1N380 1 |] op-ane Lx380 Be -03 Version 43 | 62-001 1 Switch, MOM, SPST sW4 8 4a | 66-214p2r a || switen! sest, x4, orp su3
45 | 66-1101 1 oe" ya, pre sw 46 | 69-004 1 || switch, sep, sutoe sw2 a7 | 72-1608 2 |] screw, ‘Pan Ha, Phil, #6-32 x 4 1g, CRES 43 | 75-016 2 || washer, Flat, #6 ax | 75-056 2 || washer, tock, mM, #6 50 } 75-916c 2 || nut, Hex, #6-32, CREs = si | 78-0001 1 |] weatsinn’ (ua323)
—= 52} 78-1605 1 f} sitpaa (2323) Hem |__Part Number _ | @ty- Desoription 53 | 79-4278 2 || socket, 26 bin, tow Insertion x |) esovactz 2 | peipemtesouty sak sa | 79-4270 3. || socket! 40 Pin, tow insertion +) mo 7 nen Sheet Se, ea 7 on = 55 | cozol77-1 1 |) crystal, 3.579575 viz
- wees 2 pe me ae a 56 } cono7ea 1} Coston 1c (xa) 2/3
- int a oe ten. 4 ae 57 { co1o745 1 |] te (6507 > 23 ¢ | ier ee © ae eeraaMoede-37 ss | co1o7so 2 |} xc wtaess2) ca/s, 24/5 1 dete 59 | 030929 1 |[ Play 12 Program nox 0 3/22 6 | torsset 4 ; 3 RB-EAg.42 60 | 020753 1 |] etay 12 Program ROM 2 N/34 7 10-597 3 ~ 2 oe ye 746, Bal 1 | 030756 1 {| Play 12 Program PRON 1 AS a | lo-si02 10 " 1x R12, 15,16,17, 30,38 eS | saves (PES 22 Seen et at
39,40,41,47 bs 9 | 10-sis2 i . * 1.3K 533 . . to | igecied : : a Des ee 64 | 10-5560 1 || Res, Carbon, 5% 1/4W, 56 Ohm BSL ae | jocsgea an Pa brie 68 | s4-2Nooud 1 || Transistor, 2N6o44 ae 12 | 10-5332 5 " 313K R18, 19,20,21,22 13] 10-5382 rfnoe 319K R31 as | 10-sa72 3 {so gle R713, 15 | 10-5103, 1} " LoK 245. 16 | 20-5473, 1 ease Ras a7} 10-8154 1 "6" Ls0K R27 18 | 10-5105 1 “sw a3 a9 | 10-5228 rf os “2am Rea 20 | lo-sis6 1 | Res, carbon, 58, 4H, 17M 242 21 | 19-315103 1 | trimot, 58, 5W, LOK R09 22 | 21-1olaee 1 | cop, mylar,” .oolut 28 23 | 21-1oises af Secu €24, 25,26,27 2a | 21-0147 rf lene c3s 25 | 24-250105 1 | cap, Elec. int, 25v c38 26 | 24-250075 1 4.708, 25 37 27 | 24-250226 1 2aue,'25v c36 28 | 24-250107 a > Lou, 25 cas 29 | 27-250102 1 | cap, cer Disc .00lue, 250 ce 30 | 27250103 Pen “onus, '25v c1,4o zi} 27-250108 Pn live," 25v €3°8,11-23,29-34, 39]
t 42,42,C9,16 a2} 2-011 1 | cap, cer Mono. .22uf, 12v, caa 33 | 31-1s100 2 | Diode, 1200 cn2.4 3a) 31-ana.a 2 o" GNoLE crl,3 35 | 23-2N3206 2 | teansistor, 23906 oa as | 34-anai2a 1 * 2Ka124 93 a7 | 37-4050 1 | me. cet. 4080 a6 38 | _37-74c02 2 |" "— 74co2 27,08 Ox
- . TL Figure 5-4 Tournament Table PCB Assembly Parts List
Item[ Part Number [gty. DESCRIPTION 39 | 37-7416 1 |] aw. cer. 7416 27 40 | 37-74156 1 "e” qa156 a/eL 41 | 37-nM323 1 || Reguiator 11323 -04 Version 42 | 37-14360 1 || op-amp —xx300 ne Oy 43 | 62-001 1 |] switch, mom, ses sua
44 | 6e-21407 1 || switch, sest, x, pre SH3 46 | 69-004 1 || switen, spor, stipe sw2 47 | 72-1608c 2 || screw, Pan Ha, Phil, #6-32 x 4 bg, CRES 4a | 75-016 2 || washer, Plat, #6 49 | 75-056 2 || washer, tock, mr, #6 50 | 75-916c 2 || wue, Hex, $6232, CRES si | 78-0602, 1 |] weatsink’ (20323) mNumber [awe 7 52 | 78-1605 a |} stipaa (323) Hem |_Part Number __{atye Deseription 53 | 79-4278 1 || socket, 28 Pin, Low Insertion 1 | oscr71-01 1 |peestea Gureode) soar, 5a | 79-4270 3. || socket, 40 Pin, Low Insertion a | fests ide i ES 57 } co10745 a |] xc (6507 ) 53 s | igea s |: Ho B54, 95,36,37 53 | cotorso 2 || PBR can sew 0 cape Bars 6 | 10-5301 a |e "350 RB,9,10,11 go | sone 1 |] play 12 program RoM 1 n/B3 7 | to-sa7a 3 | « 470 R6,46 , 50 | & | oaezse. 1 || sing 12 Provram:- Prod 2 25 @ | ro-si02 vfs "8 ok R12, 18,16,17,30,38 2) oars. 2 || zsh 12resdeam prom 2 BS
39,40, 41,47 3 2, | ace 3 : iia Be 2,2428.26 | 64 | 10-5560 1 |] Res, Carbon, 5%, 1/4W, 56 Ohm RSI ar | ‘Go-g299 4 " 2K one 65 | 34-2N6oas 1 |} transistor ,” 2N6044 a az | 10-5332 5 " 3.3K RLe,19,20,21,22 13 | 10-5392 1 ” : 3.9K R31 1a | 10-8472 3 * "8 47K R7,13,14 1s | 10-5103 1 10K RAS as | 10-5473 1 47K R48 a7 | io-sisa 1 150K R27 is | t0-s105 1 ” ut R43 is | 10-8228, 1 * 22M Rad 20 | 10-s1s@ 1 | Res, cazbon, 58, 4H, 15M R42 21 | 19-315103 1 | teimpot, se, 4#, LOK R49 22] 2i-ioi102 1 | cap, Mylar, .oolus c2a 23 | 21-101683 4 .O6sut €24,25,26,27 2a | 21-101474 1 lara 35 25 | 24-250105 1 | cap, Elec. lug, 25 38 26 | 24-250475 i | 4.708, 250 37 27 | 24-250226 a} o" * 22ug,‘25v C36 28 | 24-250107 ri 100uf, 25v ca3 29 | 27280102 1 | cap, Cer dise .o01ue, 25v c2 30 | 274250103 2 " colué, 25 e140 31 | 27-250104 so fs sue, 250 c38,11-23,29-34, 39,
41,42,09,10 32] 29-012 1 | cap, cer Mono. .22ug, 12v, cae 33 | 31-1m100 2 | Diode, 1100 cR2,4 34.| 31-1n914 2 oO" qya14 cal,3 3s | 33-2n2906 2. | transistor, 23906 91,2 36 | 34-2naiza 1 * 2Na124 03 37 | 37-4050 a | tne. cre. 4050 26 3a | _37-74c02 2 |" 74c02 27,08 © \Waerconmaremons Gomory
teddy
26) 2 PLCS Q).
2 PLCS @2 :
- 2 PLCS
- 2 PLCS
- 2 PLCS
- 2 PLCS
- 2 PLCS
OR YEL
OR/BK YEL/BK
BK/OR BK/YEL
Figure 5-5 Coin Door Assembly A006794-01 through -07 F ign formation sh ight to reproduce this drawing or an sr manulacture by vendors of Alan Incor (@) 4 PLCS
W TQ) 2 Pics
27) pos Bs
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
own, part
i unless by written agreement tien permission trom the corporation. N
Figure 5-5 Coin Door Assembly || Parts List ATARI
; Item [Part Number Qty. Description A007637-01 Front Bezel Assy. - Used only on -01 Coin Door Assy. 4007637-02 Front Bezel Assy. - Used only on -02 Coin Door Assy.
| . | A007637-03 | Front Bezel Assy. - Used only on -03 Coin Door Assy. |
A007637-04 Front Bezel Assy. - Used only on -04 Coin Door Assy. A007637-05 Front Bezel Assy. - Used only on -05 Coin Door Assy. A007637-06 Front. Beze] Assy. - Used only on -06 Coin Door Assy. A007637-07 Front Bezel Assy. - Used only on -07 Coin poor Assy. 75-9165 Nut 6-32 %007639-01 Coin Lock~Out Assembly A007640~01 Coin Switch Assembly 002465-03 Coin Counter Assembly 004320-01 Coin Door Weldment 004341-02 Secondary Coin Chute
| - | 004344-01 | Key Loop |
004340-01 Spring-Return
| é | ‘ | 004337-01 | Bracket, Wire Form |
004338-01 Lock-Out, Wire Form, R.H. 004336-01 Lock-Out, Wire Form, LH. 004326-01 Button, Scavenger 75-046 Lock Washer, #6 006904-01 Spacer 007359-01 Lamp Socket 70-11-47 Lamp 73-3008 Retaining “C" Ring, Truare #5103-25 75-9914001 Self-Vhreading Wut, Tinnerman #SR188006 75-0268 Washer #6 75-00516 Kepnut, Style 842, Stl., 6-32 008629-01 Spring 71-2118 Lock Assembly, Hudson Lock 71-1225cU Coin Mechanism for American Quarter only 71-1205 FF Coin Mechanism for Belgian 5 Francs Only
| . | 71-1201 MG | Coin Mechanism for German Mark only |
71-1201S Coin Mechanism for Swedish Krona Only 71-12100¥5 Coin Mechanism for Japanese 100 Yen Only
| ‘ | 71-1210PE | Coin Mechanism for English 10 Pence Only |
71-1220CA 007753-01 A0076 38-01 A006921-01 © 4 warner Communicavions Company Coin Mechanism for Australian 20-Cent Piece only
Plate, Anti-Probe Switch Assembly - slam Harness Assembly
FILO K09) i)
a feceesi [2
- o Ql
CONFIDENTIAL without the
Figure 5-6 Power Supply Assembly A007197-01 H
A ATARI Figure 5-6 Power Supply Assembly Parts List
| Item | Part Number | Qty. | Description |
| 1 | A009266-01 | 1 | Power Supply Base Weldment Assembly |
| 2 | A006886-01 | 1 | Transformer Termination Assembly "Type B" |
| 3 | 29-053 | 1 | Cap., Sprague Electrolytic 26,000uf @ 15V |
| 4 | 78-70501SC | 1 | Brkt., Cap. Mtg. Sprague #4586-48 |
| 5 | A006555-01 | 1 | P.C. Board Rectifier |
| 7 | 79-4411004 | 5 | Fuse Holder, Panel Mounting |
| 8 | 41-2003 | 1 | Filter, Power Line, 5 AMP |
| 9 | A006958-01 | A/R | Volt Sel Block 95V |
| 10 | A4006958-02 | - | Volt Sel Block 110V |
| 11 | A006958-03 | " | Volt Sel Block 205V |
| 12 | A006958-04 | " | Volt Sel Block 220V |
| 13 | 78-2708 | 1 | Grommet,Plastic |
| 14 | 72-1810S | 9 | Screw Pan Hd., #8-32 x 5/8"Lg. |
| 16 | 75-048 | 9 | Washer, Split-Lock #8 |
| 17 | 75-9188 | 9 | Nut Hex #8 |
| 18 | 75-0188 | 8 | Washer Flat #8 |
| 19 | A007192-01 | 1 | Power Switch Termination |
| 20 | A007444-01 | 1 | Power In Harness |
| 21 | 46-203801 | 1 | Fuse, 8 AMP, 125V, 3 AG Fast Acting |
| 22 | 46-201251 | 2 | Fuse, 24 AMP, 125V, Slow Acting |
© 4 warner Communications Company
lo-1onogo
Figure 5-7 Harness Schematic mavaas
Vaal oars Save
Gass gapnnn wece “ey peso isms Ered avis om Iolo ells
TSN 0 ASR SOL to-LeiLse ||
re) eR £ wouinow ouywanss fee! “Saans [fe panos fe) wOLaNNoD sods Ses 6>
aS BOs |SpRen +
- ‘of aan
ew
Orge
TV MONITOR SERVICIN INFORMATION
This chapter provides servicing information taken from the Motorola and TEC service manuals. Each manual has been reprinted by permission of the respective monitor manufacturer. Your game will include the Motorola or TEC monitor, depending on their availability during production.
M5000-155 M7000-155
MOTOROLA
Service Manual
A. GENERAL INFORMATION This manual contains information on the M5000/M7000 monitor series and the +5 volt logic power supply. The M5000 uses a 19-inch CRT and the M7000 uses a 23-inch CRT. All CRTs are of the magnetic deflection type with integral implosion protection.
All monitor power supplies are capable of producing both +73 and +12 volts regulated from either 115-volt or 230-volt AC input to the transformer primary. All monitor variations described herein require a composite video input signal.
mn SAFETY
1, Safety procedures should be developed by habit so that technicians rushed with repair work automatically take precautions.
- A good practice, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.
- Extreme care should be used in handling the picture tube as rough handling may cause it to implode due to atmospheric pressure (14.7 Ibs. per sq. in.). Do not nick or scratch glass or subject it to L any undue pressure in removal or installation. . An isolation transformer should always be used Input and output connections for the monitors are made through a 12-pin connector plug located at the rear of the chassis. Inputs consist of composite video, audio, and 115/220 voit AC three-wire.
All monitors employ: four stages of video amplification, a two-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep circuit, a one-stage spot kill, a one stage blanking amplifier; and a regulated, full-wave bridge power supply.
Model Breakdown Chart
Model Video Input 19" CRT 23” CRT
IM5000-155 Composite x
IM7000-155 Composite x
during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in personal injury from electrical shocks. It will also protect the chassis and its components from being
PART NO. 6526253047 COPYRIGHT 1977 BY MOTOROLA, INC. & MOTOROLA Data Products _ caroistream, Luinots 60187 PRINTED IN U.S.A.
acar r vise
cd su as fr
ve voltag damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.
- Always replace protective devices, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.
- Before returning a serviced unit, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock. Do not use a line isolation transformer when making this test. = 1000-0HM/VOLT (OR HIGHER) AC VOLTMETER NOTES: 1. REPEAT EACH CHECK WITH THE LINE CORD, REVERSED IN THE POWER OUTLET.
- METER READING MUST NOT EXCEED 7% VOLTS AC. HOT" LEAD OF METER TO EACH EXPOSED PART OF CABINET,
AS WELL AS THE CABINET
Voltmeter Hook-up for Safety Check In addition to practicing the basic and fundamental electrical safety rules, the following test, which is related to the minimum safety requirements of the Underwriters Laboratories, should be performed by the service technician before any unit which has been serviced is installed in a game again.
A 1000-ohm-per-volt AC voltmeter is prepared by shunting it with a 1500-ohm, 10-watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.
The AC voltage indicated by the meter must not exceed 7% volts. A reading exceeding 7% volts indicates that a potentially dangerous leakage path exists between the exposed portion of the unit and earth ground, Such a unit represents a potentially serious shock hazard to the operator.
The above test should be repeated with the power plug reversed, when applicable.
Never reinstall a monitor which does not pass the safety test until the fault has been located and corrected.
Table 6-1 Motorola Monitor Electrical Specifications
MODEL M5000-155 MODEL M7000-155
PICTURE TUBE
standard 19" measured diagonally (48.2 cm); 184 sq. inch viewing area (1188 sq. cm); 114° deflection angle; integral implosion protection; P4 phosphor 23" measured diagonally (58.4 cm); 282 sq. inch viewing area (1820 sq. cm); 110° deflection angle; integral implosion protection; P4 phosphor standard
[rower INPUT
115/230 VAC, 110 Watts (nominal); 60 Hz provision for 230 VAC, 50 Hz
FUSES M5000-155, M7000-155—0.8A.
+73 VOLT SUPPLY to 260 VAC Electronically regulated over AC inputs from 103 VAC to 130 VAC, or 260 VAC
VIDEO INPUT 0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT
RESOLUTION 500 lines at picture center
LINEARITY Within 3%, measured with standard EIA ball chart and dot pattern
Table 6-1 Motorola Monitor Electrical Specifications
HIGH VOLTAGE 17KV (nominal)
HORIZONTAL BLANKING INTERVAL 41 microseconds typical (includes retrace and delay)
SCANNING FREQUENCY Horizontal: 15,750 Hz+500 Hz; Vertical: 50/60 Hz
ENVIRONMENT Operating temperature: 10°C to 55°C (ambient) Storage Temperature: —40°C to +65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure
L UL listed under specification 1410 (electronic components)
TYPICAL DIMENSIONS (35.8 x 46 x 37.6 cm) 14.11" H, 18.18" W, 14.83" D 16.72” H, 21.56" W, 16.18" D (42.4 x 54.7 x 41 cm)
Specifications subject to change without notice.
B. SERVICE NOTES
Cireuit Tracing Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, control names are also shown and referenced on the schematic diagram in this manual.
Transistor elements are identified as follows: £—Emitter, B—Base, C—Collector.
Component Removal Removing components from an etched circuit card is facilitated by the fact that the circuitry (copper foil) appears on one side of the circuit card only and the component leads are inserted straight through the holes and are not bent or crimped.
It is recommended that a solder extracting gun be used to aid in component removal. An iron with a temperature-controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foil due to over-heating.
The nozzle of the solder extracting gun is inserted directly over the component lead and when sufficiently heated, the solder is drawn away, leaving the lead free from the copper foil. This method is particularly suitable in removing multi-terminal components. CRT Replacement Use extreme care in handling the CRT, as rough handling may cause it to implode due to high vacuum pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection. In addition, be sure to disconnect the monitor from all external voltage sources.
- Discharge CRT by shorting 2nd anode to ground; then remove the CRT socket, deflection yoke and 2nd anode lead.
- Remove CRT from the front of the chassis by loosening and removing four screws, one in each corner of the CRT.
Adjustments A non-metallic tool is recommended when performing the following adjustments.
Regulator Adjustment
- Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
- Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service.
- Adjust HOR. SET coil 11 until display is stable.
- Connect a DC digital voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q17, or any +73 volt test point.
- Adjust the 73V ADJUST. control, R93, for an output of +73 volts. Do not rotate the control through its entire range; damage to the monitor may result.
- When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible.
Horizontal Hold/Oscillator Adjustment Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical or the CRT display is stable (synced).
Vertical Height/Linearity Adjustment
- Connect a test generator whose output is similar to the display signal normally used.
Motorola Monitor Circuit Board in Service Position Figure 6-1
- Rotate the vertical size control, R60, until the smallest display is obtained.
- Adjust the vertical linearity control, R64, until the top and bottom of the test pattern is equally spaced.
- Readjust R60 until the desired display height is obtained.
- Readjust R64, if necessary, as in Step 2 above.
Focus Adjustment The best overall focus of the display is obtained by adjusting the focus control, R42, for best focus ata point which is near the center and approximately 1/3 down from the top of the display.
Monitor Servicing The monitor circuit board may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see Figure 6-1).
C. THEORY OF OPERATION Power Supply The power supplies are transformer-operated, full-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.
+73 Volt Supply (See Figures 6-3,6-4) When the +73 volt supply attempts to increase, the voltage at pin 3 of IC1 will increase, while the voltage at pin 2 remains constant due to D20. The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (pin 6) to increase the forward bias of Q19. The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of Q17 collector-to-emitter voltage will cancel the attempted output voltage increase.
When the +73 volt supply bus attempts to decrease; the voltage at pin 3 of IC1 will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19. The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series
COMPOSITE EMITTER VIDEO ian FOLLOWER
woeo ono
WoRZ on eye, L once Honiz, Hos ourPut VOLTAGE 145/230 REGULATED wan VOLTS. Ac POWER | ——O+42v} weut (| surety | a
BLANKING MPL,
sync SEPARATOR VERT, SYNC INTEGRATOR
Figure 6-2 Motorola Monitor Block Diagram
a4 150 WV "iow Qu? Agw REGULATOR
quy Ble REG, BUFFER
with the output, will decrease proportionally to the attempted decrease in the outbut bus.
Resistor R84 shunts a portion of the output current around Q17 so less power is dissipated within the device. Resistor R82 is the current-limiting resistor for Q18, and R86 controls the leakage current of Q17. Resistors R83 and R85 are the collector load for Q19, and R88 and R87 provide an emitter voltage for Q19 within the range of IC1’s output voltage variations. Capacitor C45 filters high frequency variations from the voltage at pin 7 of IC1, and C49 is a Miller-effect capacitor which eliminates instability. , PARABOLA ) FROM EMITTER : OF Q17
EXISTING VERTICAL SAWTOOTH WITHOUT VERT.PARABOLA ; ADDED
PARABOLA PULSE AND. VERTICAL SAWTOOTH ADDED TOGETHER, HENCE PRODUCING THE REQUIRED VERT. DRIVING SIGNAL
Figure 6-4 Motorola Monitor Vertical Drive Waveform
INPUT C47
GND 2
R6
10 C33 +73V +150V co R14 git « wey i Kew =
| os | as | |= |
cz ~ | a ] ook Ql AgH EMITTER
DRIVER aw C8 ais 3 220
| gus 3307 | 022 | Ving o |
| 7 | All | TO PIN 7 |
aie = CATHODE |
| + | oF | OF V1 (CRT) |
VIA R78 cn) = ToQu EMITTER coltecToR
Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit
Capacitor C32A filters horizontal frequency variations from the output bus,
Resistor R91 provides bias current for D20, and the value of R99 presents an impedance from pin 2 of IC1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output bus, back to pin 3—preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equal to the voltage of pin 2 of IC1. Resistor R95 provides bias current for D21 and also provides the +12 volt output. Diode D23 is necessary to temperature-compensate for variations within D21. Capacitor C328 filters AC variations from the output of the full-wave bridge.
Video Amplifiers and Output (See Figure 6-5) The composite video signal is coupled to the emitter-follower Q1 through the input connector P1 and capacitor C1. Transistor Q1 is a buffer stage which matches the impedance of the signal source to the video preamplifer and the sync separator stages. Resistor R1 is a terminating resistor for the video signal source, and resistors R2, R3, R4, and R5 form the biasing network for the stage. Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Q1 to the sync separator Q10 through C33 and to the contrast control R6 through C47.
The contrast control varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct-coupled, common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedback arrangement of R9, R10, R11, and R12. Resistors R7 and R8 provide the base bias voltage for Q2. Capacitor C48 is used for high-frequency peaking.
The output of the video preamplifier stage is coupled to the video output stage through capacitor C4. Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when a sync pulse turns on the sync amplifier Q11. The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7, C8, and resistor R16 are used for highfrequency compensation, and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts, while capacitor C5 filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2, and R19 and D4 are used to limit the current through the CRT.
R25 R24 33.3K sok puam Q6 Ab) HORIZ OSC. Eau Qa ASF HORIZ ORIVER aa sas, HORIZ ORIVER
R35 165K
R37Ic23,
ca7R39
+7
Figure 6-6 Motorola Monitor Horizontal Deflection Circuit
Capacitor Ci0 AC-couples the video from the collector of Q5 to the cathode of the CRT if D4 turns off due to high beam currents. Resistor R17 is the collector load for Q5, and R15 provides the bias current for the zener diode D3. Capacitors C9 and C6 filter video frequencies from the +150 volt and +12 volt supplies. Resistor R14 and zener diode D1 are used to supply +12 volts for Q1, Q2, and Q3.
D. HORIZONTAL DEFLECTION CIRCUITS (See Figure 6-6) Phase Detector (See Figure 6-7) The phase detector consists of two diodes (D5 and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base.
The horizontal output (Q9j collector pulse is integrated into a sawtooth by R24 and C12. During horizontal sync time, diodes D5 and D6 conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. If the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis, and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). The positive polarity causes the horizontal oscillator to speed up and correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D).
Components R23, C15, R25 and C17 comprise the phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor C13 times the phase detector for correct centering of the picture on the raster.
Horizontal Oscillator The horizontal oscillator employs the principles of the Hartley-type oscillator. Its operating frequency is sensitive to its DC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector. The main frequency-determining components are L1, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off. The initial forward starting bias is supplied via R26.
Horizontal Pulse Shaper and Driver The horizontal pulse shaper Q7 serves as a buffer stage between the horizontal oscillator and driver. Capacitor C20 and resistor R30 combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.
A REFERENCE | HORIZ. SYNC
OSC,ON FREQ Bo NO CORRECTION VOLTAGE DEVELOPED
OSC.SLOWS, POS. CORRECTION VOLTAGE
OSC. FAST, NEG. CORRECTION VOLTAGE
Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms
The horizontal driver Q8 operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.
Resistor R35 and capacitor C21 provide damping to suppress ringing in the primary of T1 when Q8 goes into cut-off. Resistor R36 is used for limiting current in the collector of Q8, and C22 filters the horizontal frequency variations from the DC side of the transformer primary. Horizontal Output (See Figure 6-8)
The secondary of T1 provides the required low drive impedance for Q9. Resistor R37 limits current in the base of Q9, while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which once each horizontal time period connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of T2. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The horizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Momentary transients at the collector of Q9, should they occur, are limited to the voltage on C27, since D8 will conduct if the collector voltage exceeds this value.
The damper diode D7 conducts during the period between retrace and turn-on of Q9 to reduce retrace overshoot; capacitor C28 is the retrace tuning capacitor. Capacitor C25 blocks DC from deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor 32D is charged through D10, developing the video output supply voltage.
‘1D DAMPER |.01 a HORIZ LIN BOO 5 = Laa wont HORIZ YOKE
| WioTk' | (00) | ou pey | |||
| gag | O6 | neo | aaall | »- | ||
| 02s | — | Hae RECT. | |||
| ga 7696 | acre | ee | |||
| i. | Tleiyen | HoRI2 QUTPUT | op | — | = |
3a HOR2 DRIVER ay Me TO PING
| cOMcTOR | ar | +loze |
HEATER VOLTAGE FOR V1 c22 on Dio TO PINT
| = | c27] | 3R39 | ‘AOS | = |
| pe | $330k | . | ||
| uo | 0 | Fossey] *! | my. | |
| tloseo | TRANS. | 10 | ||
| 10 | = | ——| | 20 | cRT |
| R3e | = | 2nd ANODE, |
Ra: +73V i u 1 15,
| Toc | rae | i |
56K To ew cre | [OAT cea peice
Figure 6-8 Motorola Monitor Horizontal Output Circuit
VERT. SYNC. INTEGRATOR U™ REA ABS +i
Qu3 Law AGL VERT. SYNC. AMPL.. o.03v TO C36 3.3K ]3.3K,2W| o35 e347 +6047
Figure 6-9 Motorola Monitor Sync Circuit Syne Circuits (See Figure 6-9)
The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negativegoing sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction. The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information.
Resistors R45 and R46 provide base bias for Q11. The composite sync pulses are amplified and inverted by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for Q11, and also provide base bias for Q12. Resistor R50 limits current through the base-emitter junction of Q12, and R51 is its collector load. Components R52, C34, R53, C35, and R54 form a double integrator which removes the horizontal pulses from the composite sync signal, leaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.
Vertical Oscillator and Output (See Figure 6-10) The vertical oscillator is a relaxation oscillator and operates at a free-running frequency that is set by
+73V
+12V
} us | VERT. R60 A) | CHOKE! R56. R Sek Sek Vv) R66 c40 cal + [> To R68 10.13 100 | 0.1 COLLECTOR o37| qs conn 0 82v 0.22 VERT. ouTPUuT Lag 3.3KE VERT. YOKE VERT. yo13 ©38 ose. FANS aS R67 R65 10 W
Figure 6-10 Motorola Monitor Vertical Oscillator Circuit
the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until D12 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When D12 conducts, C37 and C38 are discharged to nearly zero volts; then D12 turns off and the cycle repeats. The value of R61 and the setting of R60 determines the amplitude of the waveform.
Diode D14 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14; D13 provides temperature compensation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Q15.
The vertical choke L5 acts as a current source during linear scan time and provides a high-voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.
Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical non-linearity will result unless some compensation is employed.
Resistors R64 and R62 couple the emitter voltage of Q15 to the junction of C37 and C38. This path is resistive, and the waveform coupled back will be integrated by C38. This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of C37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40 couples the signal to the vertical yoke winding and blocks DC.
Spot Kill (See Figure 6-11) The spot kill circuitry is used to reduce the effect of the electron beam concentrating on one area of the CRT after the monitor is turned off. The circuitry is accomplished by raising the arm of potentiometer R73 to-the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the highvoltage charge that normally remains in the CRT.
When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage required to keep Q20 on. When the monitor is turned R73 BRIGHTNESS
CRT, PIN 2
Figure 6-11 Motorola Monitor Spot Killer Circuit
off, the falling +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 prevents the negative voltage swing at the base of Q20 from exceeding the reverse voltage rating of the transistor.
Blanking Amplifier (see Figure 6-12) The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field. Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses, while R69 determines the amplitude of the horizontal pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R70 allows C41 to discharge when the retrace pulses swing below zero volts. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.
Motorola Monitor Blanking Amplifier Circuit Figure 6-12
RO (CONTRAST) u ~ (HORIZ. OSC.) R73. 12 Raz (BRIGHT) (Focus) 12
Figure 6-13 Motorola Monitor Chassis Rear View —Component Location
went Lexo)
Tose wane YORE
row VERT: YORE
of SEE SeHEMATICNOTES TBNDe
yo
Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View
te
WILyaA
AlddNS Y3MOd
Figure 6-15 Motorola Monitor Schematic Diagram
D5/D6 (NOT
SHOWN) SHOWN)
pa ~~ (NOT
R64 R60 VERT. VERT. Di2 13 LIN.| Size
Q16 eq 020 / RG
P1 a1 P5 CONTRAST
Q6 71 Q7 &R7. D23 018 1C1
BRIGHT
2 aH meet ere
ion it Board Detail—Component Locat ircuit Figure 6-16 Motorola Monitor Ci
Table 6-2 Motorola Replacement Part Numbers
REF. PART NO. | NUMBER DESCRIPTION. NO. NUMBER DESCRIPTION
| Capacitors: | C31 | 8S10191B98 | 01, 10%, 250V; Poly. | ||
| All values are in Microfarads unless otherwise noted. | C32 | 23810255B73 | 20/200, 400/125, 600/100, | ||
| cl | 23810255A27 | 47, 50V; Lytic | 200/50; Lytic | ||
| C2 | 215135660 | .05, +80-20, Z5V, 50V; | C33 | 8S10191A51 | 033, 10%, 160V; Poly. |
| Cer. Disc. | C34,C35 | 8S10191A32—-.047, 10%, 250V; Poly. | |||
| C3, C4 | 238187A26 | 22, 25V; Lytic | C36 | 21S180E60 | .01, +80-20, Z5V, 50V; |
| cs | 21$180E60 | .01, +80-20; Z5V, 50V; | Cer. Disc. | ||
| Cer. Disc. | C37, 38,39 8S10191B67 | 0.22, 10%, 250V; Poly. | |||
| C6 | 218135660 | .05, +80-20, Z5V, 50V; | C40 | 23S10255A60 | 100, 63V; Lytic |
| Cer. Disc. | ora | 8S10212B16 | 0.1, 20%, 400V;; Mtlz. | ||
| 7 | 218131625 | 330pf, 10%, XSF, 500V; | Poly. | ||
| Cer. Disc. | C42 | 21$180C82 | 0.33, 10%, N150, 500V; | ||
| cs | 21$180B87 | 220pf, 10%, XSF, 500V; | Cer. Disc. | ||
| Cer. Disc. | 43 | 8S10191B67 | 0.22, 10%, 250; Poly. | ||
| or) | 8S510191B99 | 015, 10%, 250V; Poly. | cA4 | 23S10255B28 | 4.7, 100V; Lytic |
| C10 | 8S10212B18 | 0.22, 10%, 400V; | C45 | 8S10191B90 | -033, 10%, 250V; Poly. |
| Mtlz. Poly. | C46 | 218132492 | .01, +80-20, Z5V, 100V; | ||
| cu | 218131625 | 330pf, 10%, X5F, 500V; | Cer. Disc. | ||
| Cer. Disc. | C47 | 23$10255B63 | 100, 10V; Lytic | ||
| C12 | 21S180C41 | .0027, 10%, Z5F, 500V; | C48 | 21S180D56 | 47pf, 10%, N750, 100V; |
Cer. Disc. Cer. Disc.
| C13 | 21S180C02 | 10pf, 10%, N150, 500V; | C49 | 21S180B51 | -001, 10%, X5F, 500V; |
Cer. Disc. Cer. Disc.
| C14 | 21$180D34 | .005, 20%, Z5F, 1KV; |
Cer. Disc, Diodes:
| C15 | 23S10229A32 | 1.0, 16V; Lytic | D1 | 48S10813A03_ | Diode, Silicon, Zener; |
| C17 | 8S10191B90 | ——.033, 10%, 250V; Poly. | 1N5242 | ||
| C18 | 8S10299B28 | .01, 10%, 100V; Polycarb. | D2 | 48D67120A13 | Diode; A13 | |
| C19 | 8510299B29 | .0082, 10%, 100V; | D3 | 48S10813A01 | Diode, Silicon, Zener; |
Polycarb. IN5234B
| C20 | 8S10191B98 | .01, 10%, 250V; Poly. | D4 | 48S191A02 | Rectifier, Silicon; 91A02 |
| C21 | 21S180B51 | .001, 10%, X5F, 500V; | D5,D6 | = 48D67120A11_— | Diode; A11 |
| Cer. Disc. | D7 | 488134921 | Diode, Damper; D1D | ||
| C22 | 8S10191B98 | .01, 10%, 250V; Poly. | D8 | 485134978 | Diode, Pulse Lim; D1K |
| C23 | 23S10255B50 | 150, 10V; Lytic | D10 | 48S191A05, | Rectifier, Silicon; 91A05 |
| C24 | 21S180B51 | .001, 10%, X5F, 500V; | D1 | 488137114 | Rectifier, H.V., D2Y |
| Cer. Disc. | D12 | 485137638 | Vert. Osc.; MPU6027 | ||
| C25 | 8S10299B27 | 0.82, 10%, 200V; Mtlz. | D13,D14 | 48S191A05 | Rectifier, Silicon; 91A05 |
| Polycarb. | D15 | 48D67120A11_ | Diode; A11 | ||
| 26 | 215131625 | rosa Aaah XSF, 500V; | Bia, naa | 48S191A05 | _ Rectifier, Silicon; 91A05 |
| 27 | 8S10212A11_—-1.0, 10%, 630V; Mtlz. | D20 | 48S10813A02 | Diode, Silicon, Zener; |
Poly. 1N5231B
| C28 | 8S10571A06 | .01, 5%, 1200V; | D21 | 48S10813A03 _— Diode, Silicon, Zener; |
Polyprop. Foil 1N5242
| C29 | 8S10212B53 | (0.47, 10%, 630V; Mtlz. | D22 | 48D67120A11_— | Diode; A11 |
| D23,D24 | 48$191A05 | Rectifier, Silicon; 91A05 |
Poly.
Table 6-2 Motorola Replacement Part Numbers
| Ret. | | | Part No. | | | Description | ea | Part No. | Description |
| Fuses: | Reo | 18D25245A29 | Vert. Size; 250K | ||||
| Flnf2 | 653138263; | Fuse, O:G/A=250V. | Rod | 18D25245A31 | Vert. Lin.; 100K | ||
| Lo. | R66 | 6S10201A04 | Varistor, 1 ma, 120V, 0.5' | ||||
| Integrated Circuits: | R73 | 18D25245A28 | Control, Brightness; 200K | ||||
| 1C1 | 51$10732A01 | Ref. Ampl.; T3F | Red | 478135589 | 150, 10%, 10W | ||
| R93 | 18D25245A21_ | Control, +73V out Adj.; |
Coils/Chokes: 2.5K
| ul | 24C25448A01_ — Coil, Horiz. Osc. | R95 | 10731A03 | 1.5K, 10%, 5W |
12 24D25603A09 — Coil, Horiz. Width
| B | 24D25248A14 | Coil, Horiz. Lin. | Switches: | ||
| 4 | 24D25261A09 | Coil, Defl. (M5000-155, | swi | 40S10624A07 | Switch, Slide; D.P. D.T. |
M5010-155)
| L4 | 24D25261A10 | Coil, Def. (M7000-155, | Transformers: | ||
| M7010-155) | 1 | 25D25221A05 — Horiz.Driver | |||
| 7 | a5D25221C12, | Choke, Vertical | T2 | 24D25240B23 | HV. Transformer |
| . | T3 | 25D25239B20 | Transformer, Power |
Transistors: (M5010-155, M7010-155)
| Qi | 485137171 | Emitter Follower; AGH | T3 | 25D25239B30 | Transformer, Power |
| Q2 | 485137172 | Video Pre-Ampl.; A6) | (M5000-155, M7000-155) | ||
| Q3 | 485137127 | Video Pre-Ampl.; P2S | |||
| Q4 | 485134952 | Video Driver; A2J | Misc. Electrical Parts: | ||
| Q5 | 488137476 | Video Output; BIE | vl | 965241A01 | 19"-CRT; Type 19VARP4 |
| Q6 | 488137172 | Horiz. Osc.; A6) | (M5000/M5010) | ||
| Q7 | 488137127 | Horiz. Pulse Shaper; P2S | vi | 96510848A01 | —-23”—-CRT; Type |
| Qs | 485137093 | Horiz. Driver; ASF | M22VATP4 (M7000/ | ||
| Q9 | 488137570 | Horiz. Output; B2L | M7010) | ||
| Q10 | 485137173 | Sync Separator; P2W | |||
| Qu | 48S137172 | Sync Ampl.; A6J | Mechanical Parts: | ||
| Qi2 | 488137172 | Vert. Sync Integrator; A6) | 9B25456A01 | Block, Fuse (F1, 2) | |
| Q13 | 485137172 | Vert. Sync Ampl.; A6) | 42D25158C01 | Clamp, Defl. Coil | |
| Qi4 | 485137639 | Vert. Driver; MPS A13 | 26510251A08 | Heat Sink (Q5) | |
| Q15 | 488137596 | Vert. Output; B2V | PI | 15S10183A69 | Housing, Connector; |
| Q16 | 488137172 | Blanking Ampl.; A6] | Female (12-Contact, | ||
| Qi7 | 488137368 | Regulator; ASW | Less Contacts) | ||
| Q18 | 485134952 | Reg. Driver; A2J | 39S10184A67 | Contact, Plug; 5 Req'd | |
| Q19 | 488137476 | Reg. Buffer; BIE | M5000/M7000, 9 Req'd; | ||
| Q20 | 485137476 | Spot Kill; BIE | M5010/M7010 | ||
| . | P2 | 15S10183A82 | Housing, Connector; |
Resistors/Controls: Male (3-Contact, Less
| the description when ordering standard values of | P2 | 15$10183A81 | Housing, Connector; |
fixed resistors up to 2 watts. Female (3-Contact, Less
| Ro | 18D25245A27 = Control, Contrast; 500 | Contacts), M5010/M7010 | |||
| R14 | 178135204 | 100, 10%, 5W | 39S10184A67 | Contact, Plug; 3 Req’d | |
| R17 | 17S10731A01 | 3.9K, 5%, 5W | for P2 | ||
| R36 | 17810130B07—— | 1.5K, 10%, 3W | P3 | 28510586A35 | Header, Connector; |
| R42 | 18D25218A14_ = Control, Focus; 2M | 2-Contact |
Po
Table 6-2 Motorola Replacement Part Numbers
REF. PART PART NO. NUMBER | DESCRIPTION NUMBER DESCRIPTION
| P4, PS | 15$10183B12 | Housing, Connector; | 14B25459A01 | Insulator, Fuse Cover |
Female (3-Contact, Less (FA, 2)
| Contacts) M5010/ | 14A562353 | Insulator, Mica (Q9, |
M7010 Q15, Q17)
| 39510184A84 | Contact, Plug; 3 ea. | 14C25230A01 | Insulator, Molded (On |
Req'd for P5, M5010/ D11 Body)
| M7010 | 14S10157A30 | Insulator, Nylon (2- |
| S2 | 15$10183A81_ — Housing, Connector; | Req'd.); Mtg. P.C. Board |
Female (3-Contact, Less 14S10550A02 _ Insulator, Transistor Contacts), M5000/M7000 Cover (Q9, Q15, Q17)
| S2 | 15S10183A82 — Housing, Connector; | 35136050 | Screw, Tpg; 6-20x¥2 CLU |
Male (3-Contact, Less Pan (Mtg. Q9, Q15, Q17 Contacts), M5010/M7010 and D11 Socket)
| 39S10184A64 | Contact, Receptacle; | 9D25470A01 | Socket, CRT; incl’s. |
3 Req'd. for $2 R77, R78, R79, R80
| $3 | 15$10183A94 | Housing, Connector; | 9D25201A01 | Socket, H.V. and CRT |
Female (2-Contact, Less Anode
Contacts) 9C63825A03 Socket, Power Transistor
| 39510184472 | Contact, Receptacle; | Q9, Q15, Q17) |
3 Req'd. for S3 41D65987A01 — Spring Special; CRT Aquadag Gnd.
A. GENERAL
TM-600 and TM-623 is a television monitor for video games. It is designed for operation either from a power supply of 115 volts/50-60 Hz AC or 230 volts’ 50-60 Hz AC. The complete monitor incorporates a picture tube, an integrated circuit, 20 silicon transistors, 18 silicon diodes, 2 germanium diodes, and a high-voltage selenium diode.
This model is equipped with 5V/3A power supply for the operation of the TTL control board and operation double-pulse-type AFC circuit to obtain a stable picture.
B. SPECIFICATIONS Power Supply Input 115 volts/230 volts 50-60 Hz +10%
Power Consumption 60 watts
Video input 0.5 volts composite P/P for 100 volts 2.5 volts P/P maximum Sync negative at input TEC VIDEOELECTRONICS INC. SERVICE MANUAL
Picture Tube 19” (500 mm), 114° deflection for Model TM-600 23” (584.2 mm), 114° deflection for Model TM-623 Integral implosion protection
High Voliage 18 KV nominal at 0 microamperes beam current
Horizontal Retrace Time 12 microseconds maximum
Resolution 500 lines minimum at picture center
Scaning Frequency Horizontal: 15.750 Hz =500 Hz Vertical: 50-60 Hz
Tone Burst Amplifier 5 watts peak output with TTL drive at nominal line, fully adjustable. 4 watts peak output at low line.
Environment Operation: Maximum ambient temperature 50°C (122°F) Storage: Temperature range from —40°C to +65°C.
Model TM-600 and TM-623 Monitors
TEC Videoelectronics Inc. (TVI) 3010 Scott Boulevard Santa Clara, CA 95050 75
DEFLECTION CENTERING YOKE conte HORIZ. LIN.
HV RECT.
~ HV TRANS,
rave SWITCH —Fg93 “5 AMP. Pt DAMP. OS AMP. ‘CONNECTOR
Figure 6-17 TEC Monitor Chassis, Rear View
‘a0 ca01 conpensen — SY REGULATOR og) gy REGULATOR cant eR laa ‘CONDENS! \ i
2308 VERT. OUT TRANSISTOR
‘2305 VERT. OUT TRANSISTOR
VERT. LIN.
VERT. HEIGHT Po Js. cont. /ER TRAN: we RESISTOR eRIGHT ‘VERT. HOLD,
Figure 6-18 TEC Monitor Chassis, Top View
VIDEO ouTA!
vert. BALANCE
contrast BRIGHT Honiz. osc. con
VERT HOLD HORIZ, DRIVER TRANS.
HV RECT
HV TRANS
WIDTH com,
vert. Mi
HEIGHT, aa TO DEFLECTION YOKE
Figure 6-19 TEC Monitor Printed Circuit Board, Top View
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref. a Ref. -_
| No | Part No. | Description | No. | PartNo. | Description |
| Electrical Parts: | Q303 | 5300500201 | MPS9700U | Vert Amp | |
| PCB1 | 2215303600 | Main PCB | or MPS834 | ||
| ‘A801 | 485TM60003 | «CRT PCB | 304 | 4310400030 = 2SC1106~—Vert Output |
305 or 2N6307
| Transistor and IC: | Q400 | 5310500202 | = MPS9700T | Phase Inv |
| Q200 | 5310500202 | MPS9700T | 1st Video Amp | or MPS834 |
| or MPS834 | Q401 | 5310500202 | MPS9700T | ~Horiz Osc |
| Q201 | 5310500261 | MPS9750T | 2nd Video Amp. | or MPS834, |
| or MPS4356 | Q402 | 5310500410 | 2N6558 | Horiz Amp. |
| Q202 | 5310500410 | —-2N6558 | ~—-Video Output | or MJE9742 |
or MPSU-10, or 2N4354,
| Q301 | 5310500261 | MPS9750T | Sync Separator | 403, | 5310400040 =. 2SC1875.—Horiz Output |
or MPS4356 or MJ205
| Q302 | 5310500201 | MPS9700U__ | Vert Osc | *Q901 | 5310400030 | =—-2SC1106 | Power Regulator |
or MPS834 or MJ3430
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref. wo Ref.
| No, | PartNo. | Description | No. | Part No. | Description | |
| Q902 | 5310500410 | 2N6558 | Regulator Amp | 7 | , | |
| or 5310500070 | MPS-U04 | 7401 | 589514015. | TLN-506BX Horiz ne | ||
| Q903 5310500280 | LM1796 | Reference Amp | 7402 = 589518012 | TLN-519 | Horiz Drive | |
| or MPS-D01 | * 1403589517017 | TFB-1006AS. F.B.T. | ||||
| Q904 5310500450 | MJ2955 | ——5V Regulator | * T1901 | 589519021 | ‘TPW-600 | Power Trans |
CRT and Diode: Resistors
| * ve01 | 5380000060 | 500SB4 | CRT | R201 | RD-4L471) | 470 ohmJ % W |
| D203 | 5340200280 | MR9712__ | Silicon Diode | R202 | RD-41223) | 22K ohm | % W |
| or [N4004 | L. V. Rectifier | R203 = RD-41563) | 56K ohm J % W | |||
| D204 | 5340200430 | 1N4148 | Silicon Diode | R204 = RD-4L471) | 470 ohm) % W | |
| or IN4002__ | Blanking Clip | R205 | RD-4L332) | 3.3K ohm J %W | ||
| D205 | 5340200430 | 1N4148, | Silicon Diode | _: | *W | |
| or IN4002 | Blanking Clip | ee | a atsen | se « ohn ; aw | ||
| D206 | 5340200430 | IN4148, | Silicon Diode | 0 | y | chm |
| or IN4002 | Blanking Clip | R208 | RD-41102) | 1K ohm J %W | ||
| 0207 | 534020280 | MR9712.—-200V Rect | R210 | RS-029562) | 5.6K ohm J 2W | |
| or IN4004 | R215 | RD-42101) | 1KohmJ % W | |||
| D301 | 5340200260 | MR-9701 | Rectifier Silicon | * R216 | RD-4L101) | 100 ohm) %W |
| Diode | * R217 | RD-4L470) | 47 ohm! % W | |||
| D401 | 5340100040 | AA143 | Phase Det | R218 | RD-41223) | 22K ohm J % W |
| D402 | 5340100040 | AA143 | Phase Det | R219 | RD-4L563J | 56K ohm %W |
| pies | 5340200300 | MR9722 | Damper | R220 | RD-4L102) | 1Kohm}) %W |
| ‘D404 | 5340400120 | TV20-2K80) H.V. Rectifier | R221 | RD-41102) | 1K ohm] %W |
or HS30/Ib Ken . ’
| D801 | 5340200290 | + MR9713. | «400 Rectifier | eae | RD aba | : k on ; : w |
. ,
| (D901 | 5340200270 | = MR9704._—séReectifier | a | aki) | enn | |
| or IN4005 | Silicon Diode | R224 | RD-2L122) | 1.2 K ohm J % W | ||
| D902 | 5340200270 | ~— MR9704._—sReectifier | * R226 | RSO1P101) | 100 ohm | 1W |
| or IN4005_ | Silicon Diode | R227 | RD-2L123) | 12K ohm J % W | ||
| D903 | 5340200270 | = MR9704_—séRectifier | R228 | RD-2L105) | 1.5 Kohm} %W | |
| ows | or IN4005 | Silicon Diode | R229 | RD-AM6S1) | 680 ohm) %* W |
40200270 MR9704_—Rectifier
| or IN4005 | Silicon Diode | Rene | EDS Nest | 2 time |
7 y
| D906 | 5340300220 | INS858A_~—Zener Diode | ee | Epes) | 56K ohm) YW |
| or 5340300310 | IN@0O2A | R304 | RD-4M102) | 1K ohm J %W | |
| D907 | R308 | -RD-4M104). | 100 Kohm} %@ W | ||
| Dope ) 5340200690 | MDAS70-1__ | Rectifier | R309 | -RD-MISST | 1.5 MohmJ x» W |
| D910. | R310 = RD-4M332) | 3.3 KohmJ % W | |||
| m | R311 | RD-4M563) | 56 K ohm J % W |
Coils and Trans: '
| *L401 | 589515015 | TDY1005 | —_—D.Y. Coil | R312 | RD-4L182) | 18 Kot] | Ww |
| 1402 | 589512015 | HCH1005 — Horiz Choke | R313 | RD-41153) | 15K ohm J % W | ||
| Coil | R314 | RD-4L183) | 18K ohm J % W | ||||
| 1403 | 589512012 | HC2-035, | Choke Coil | R315 | RD-4L203) | 20Kohm) % W | |
| L404 | 589512012 | HC2-035 | Choke Coil | R316 | RS-2P333) | 33 K ohm J % W | |
| 1405 | 589514013 | AZ-9177DM_ Width Coil | R327, | RD-4L.104) | 100 Kohm) % W | ||
| 1406 = 589514016 | LH-15)54 | Lin Coil | R320 = RD-41.124) | 120K ohm) % W |
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref. Part No. Description Ref, Part No. Description
No. No. _ |
| R322 | RD-4L224) | 220 Kohm J % W | R904 | RD-2L123) | 12 K ohm J % W | |
| R323. | RD-41.433) | 43. K ohm J % W | R905 | RD-21223) | 22K ohm) %2W | |
| R324 | RD-4L471} | 470 ohm) % W | R906 | RD-2L563) | 56 K ohm} %2 W | |
| R326 | RD-4L.152J | 1.5K ohm) % W | R907 | RD-21563) | 56 K ohm J %2 W | |
| R339 | RD-4L101) | 100 ohm) % W | R909 | RD-2L682) | 6.8K ohm) %W | |
| R331 | RD-4M331) | 330 ohmJ % W | ||||
| R332 | RD-4L102) | 1Kohm} % W | Controls: | |||
| 9333 | _RSOIPORR) | 68K ohm JW | R211 | 553102005E | 1K ohm Contrast | |
| R36 | RD-41221) | 220, ohm) YA W | 327 | 5534720088 | 4.7 Kohm Vert. Linearity | |
| scaled | 2.2 ohm} YW | R335 | 553102007B | 1K ohm Vert. Balance | ||
| R338 | RS-2P150) | 15 ohm) &W | R427 | 5533030058 | 30K ohm = Horiz Hold | |
| ecaninaieel | 12° ohm} 4 W | Ra03 | 5532540058 | 250 Kohm Bright | ||
| R540 | RSOTP220T | 22) ohm | VW | R805 | 553205005B | 2Mohm_ Focus | |
| ee | Exche SS | R908 | 5534720078. © 4.7 Kohm_B+AD] | |||
| R402 | RD-4L821) | 820 ohm) % W | ||||
| R403 | RD-4M561) | 560 ohm) % W | Capacitors: | |||
| R404. | RD-4M103) | 10 Kohm J % W | C201 | CE2G1C470, | 47 mF | 16V |
| R405 | RD-4M103) | 10 Kohm J % W | 202. CE2G1F101 | 100mF | 25 | |
| R406 | RD-4L272) | 2.7K ohm J %W | C203 CE2G1C220 © -22. mF | 46V | ||
| R407 | RD-4L681} | 680 ohm) % W | 204 «CE2GIH101 | 100 mF | 35V. | |
| R408 | RS02P682) | 4.7 K ohm J % W | 205 CEZG1C220 | 22 mF | 16V | |
| R419 | RD-4L270} | 27, ohm %W | 206 CISLIHS61K | 560 pFK | SOV | |
| R410 | RD-41182) | 1.8K ohm J % W | 207 CE2G0)221 | 220mF | 6.3 | |
| R411 | RD-4L151) | 150 ohmJ % W | 208 5270322401 | 0.22 mF M_400V | ||
| R412 | RD-4L561) | 560 ohm} % W | C209 CE2G2F229° | 2.2 mF | 315V | |
| R413 | RSO1P682) | 6.8K ohm} 1W | C210 CE2G1H220 | 22 mF | 35V | |
| R414 | RD-21221) | 220 ohm) %W | C211 | CE2G1H339 | 3.3 mF | Sov |
| R415 | 5160122903 | 2.2. ohm 1 W | C213 CKIFZH102K | ~—0.001 mF_—-500V | ||
| R416 | RD-21569) | 5.6 ohm) %W | 220 CE2C2F220«2.2mF | —250V | ||
| R417 | RS02P182) | 1.8 K ohm J 2W | 301 | CQIM1H473K 0.047 mF K 50V | ||
| R418 | RSO1P123) | 12K ohm] 1W | C304. CKIBIH391K | 470 pFK = 50V | ||
| R420 | RX0SP220) | 22 ohmj 5W | C305 CE2G1H478 = 0.47 mF | 50V | ||
| *R421 | RD-21569) | 5.6 ohm) %W | C306 56405333 | 0.033 mF K 50V | ||
| R422 | RD-4L153} | 47 ohm] 1W | 307 CQIM1H562K | 0.0056 mF K 50V | ||
| R425 | RD-4L153} | 15 K ohm J % W | 308 ~—CQIM1H273K | 0.027 mF K 50V | ||
| R426 | 55337153 | 15 Kohm J % W | 309 CQIM1H123K | 0.012 MEK _50V | ||
| R802 | RD-2L154) | 150 Kohm J % W | C311 | CQIMIH124K | 0.12 MEK 50V | |
| R804 | RD-21474) | 470K ohm J %2 W | C312 CQIMTH392K | 0.0039 mF K 50V | ||
| R811 | RD-21561) | 2MQ) ¥2 W | 313 | DS5D1C229M | 2.2 mF | 16V |
| *R901—_RX20P251) | 250 ohm J 20 W | C314 CQIM1H474) | (0.47 mF | 50V | ||
| R902 | RD-2L101) | 1Kohm] %W | C315 CQIMTH333K 0.083 mF K 50V | |||
| R903 | RD-2L123} | 12K ohm) %W | C316 CF2GIA470 | 47 mF | 10V |
—___]
Table 6-3 TEC Monitor Replacement Parts Numbers
a Part No. Description Ne Part No. Description
| C317, | CE2G2A101 | 100 mF | 100V | ses: | ||
| C318 = CKTE2H103K = 0.01 mF | 500V | F992 | 6990620011 | 250V 2 Amp. | ||
| C319 | 5270310301 | 0.01 mF | 630V, | *F903 | 5990610013 | 250V 0.5 Amp. |
| 0.01 mFK | 50V | F904 | 5990630010 | 30V 5 Amp. |
C401 = CQ1M1H103K 402 CQIM1H103K
403. CQIM1H393K C404 CK1B2H151
C405 CE2G1H339 406 = CQIM1H104K C407, CQIM1H223K C408 =< CQ1M1H683K C409 CE2G1F470
C410 CK1B2H681K
C411 CK1B2H222K
C412 CK1B1H152K
C413, CK1B1H102K
*C414 CK1B3D471K
C415 CQIM2A104K *C416 5270333201
C417 CE2G2C100
C418 5270333401
C419 56635101
C420 56625471
C801 5270356302
*C901 5240700400
C904 -F2G2C229
C3905 CKIF2H102K
C911 56625105
C912 56616018
Discharge Gaps: Z801 za) 599030001 Z803
Switches: “*SW-1 — PE13-1567 0.01mFK 50V
0.039 mF K 50V
150 mE 500V
3.3 mF 50V O.1mFK — 50V 0.022 mF J 50V
0.068 mF J 50 V 47 mF 25V
680 pFK 500 0.0022 mF K 500V
0.0015 mF K 50V
0.001 mF K 50V
470 pFK —2KV O.1mFK — 100V 0.0033 mF 1.5KV
10 mF 160V
0.33 mF K —-200V
100 mF 35V
470mF —.25V
0.056 mF K 630V
450 mF 200v
100 mF 160 V
2.2 mF 160V
0.001 mF —500V 10000 mF = -_25V 1mF 16V
EGP-H751A
115v/230V Power Line
Slide Switch Mechanical Parts: *Koo1 — 22-463020 60085005
S-A3915
*TM60085001
‘or *TM60085001
KO05 —1-360826-0 P401 — PE19-1569 402 PEI9-1570
P4Q3-PE19-1571
A621 PE19-1572
A631 PE19-1573
P406 — PE19-1574 P407 — PEI9-1575 TES01 PE19-1576
£001 135431015, Fool = .22-164001 003 5432001-1
Q403D 34320011 Mate-N-Lock Connector (AMP) Edge Collector (Molex) Transistor Socket (SMK) Fuse Holder
Fuse Holder
Stand-Off Fastener (AMP)
AP Plug Assy. (Yoke Line) 4F Recep Assy (Yoke Line) 3P Connector Assy. (Video Input) 4P Connector Assy. (Q901 Line) 6P Connector Assy. (Q304/Q305 Line) 2P Plug Assy. (Heater Liney 2P Recep Assy. (Heater Line) Terminator, 6 Pin Ground Plate
Frame
Plate Heat Sink A
Plate Heat Sink C
- Design and specifications are subject to change without notice.
2, J—Indicates + K—indicates + 5% tolerance
10% tolerance
M-—~Indicates +20% tolerance
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Safety-Critical Components Components marked with an asterisk (*) on the parts list and with gray shading in the schematic have special characteristics important for safety. You may Create shock, fire, or other hazards by using a replacement that does not have the same characteristics as the recommended part.
© 9907 “2910 mORS70 1
‘ew-623 } TPW-600
TR, IC, and Connector Lines
c MES UIO— LMi736 MPS 9417 INSUSBA MPS Uoa 2Ne58@ MPS 9750 MPS 9709 1NEOOZA
ace ece Mues20 MuE105 Mc 7e0sce = MUES742
2st! 108 280 1675 Fogo1.oace Six Commgro¢ | aR ‘paws
| a He
- Unless otherwise specified, all resistance values are in ohms.
- Unless otherwise specified, in the schematic diagram all capacitor values less than 1 are expressed in mfd, and values more than 1 are in pid.
- Voltage readings are taken with VTVM from point indicated on chassis to ground. NOTES
- All waveforms are measured with strong signal input and contrast set to give normal picture.
- This schematic diagram covers basic or representative chassis only. There may be some differences between actual components on chassis and the schematic diagram.
G21 CONTRAST wes 87807
VERT HOLD
HEGHT
9303 [4 mes.27004}
Figure 6-20 TEC Monitor Schematic Diagram
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
+ Le
BOTTOM VIEW
Figure 6-21 TEC Monitor Wiring Diagram
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
\
Cut along this line
TM-113 1st Printing YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefuiness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm - 0 Distributor () Operator
Address CO Other City State Zip
Tape This Edge
Atari, Inc. P.O. Box 9027 Sunnyvale, CA 94086
\ ploy puooes
Buyeeulbug do-ui0g ‘dnosy suonesyqng “unYy
© 980b6 elusOyeD ‘ayeaAuuns 2 2206 XO ‘O'd 3 ‘our ‘UeIW a = & > a
WO ‘areakuuns VOOL# WWIad SSPID ISJl4
POL ISHS -- ee ee ee ee ee ee
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and «vorkmanship under normal use and service for a period of ninety (90) days from date of shipment, Seller warrants that its television moniters (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail te conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are teturned prepaid to Sellers’ plant; and
- Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and-were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. 7
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER’S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUMF FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential Custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
‘Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.