Tempest ST-190 3rd Printing Backdoor Sheet
Tempest (rev 3, Revised Hardware) (Atari, 1980) · Backdoor Sheet · 1 pages · original scan
Self-Test Procedure
‘The information below is displayed on the screen if you set the
self-test switch to on during the attract mode. Look at the displayed numbers for SECONDS ON and SECONDS PLAYED. It these numbers run together vertically, make adjustments to the XBIP and Y.BIP potentiometers on the game PCB.
COIN MECH X11 . MULTIPLIER “| BONUS ADDER SWITCH AT N13. To go to Self-test Part 2, rotate the control knob until the mes: sage PRESS FIRE AND SUPERZAPPER FOR SELF-TEST appears on the monitor. Then press both FIRE and SUPERZAP. PER. To end the operator information display, set self-test switch to off.
TIME GAME ON (Seconds)
TIME GAME PLAYED (Seconds)
NO. OF ‘PLAYER GAMES,
NO. OF 2PLAYER GAMES.
AVERAGE 0. ‘To change toggle positions on the switch assemblies, you need ST-190 3rd printing
Game Option Settings
When changing the options, verity proper results on the mont
| GAME TIME | not remove the game PCB. The switches are accessible when the | tor display by performing the self-test. Note that changing an op: | ||||
| —— | not | somone | ||||
| in | Paes | fempest™ | Analog Vector Generator PCE is mounted in pace. To | _tion on any of the following eight toggles wil nl cause an imme | ||
| switcH | 1 | wire | as possible | |||
| TOGGLE 1 | = | — | 8 | —_____— | — | — |
‘Settings of Toggle Switch on Tempest Analog Vector-Generator PCB (at 12)
| SWITCH AT L12 | _ | —— | 1 | 2 | 5 | 6 | 7 | Option |
| (Game Play) | <<>> mEDIUN, | a | On | 1-credit minimum | $ | |||
| uves | Off | ——_2.ereat minimum |
PER GAME On ‘On English $
| fe renin areas | GAME | on | off | French |
| Poe EVERY | PRR | man] FFicuury | of | on | German |
COIN MODE OPTION on off Spanish
| us | lite | granted at ever |
NO. OF LANGUAGE ‘SWITCHES Bonus life g ry:
| CREDITS | (English) | on | not | 10,000 points | |||
| On | On | On | 20,000 points | $° | |||
| On | Of | On | 30,000 points | ||||
| Operator Information Display | On | off | ott | 40,000 points | |||
| off | On | On | 50,000 points | ||||
| of | Ont | £0,000 points | |||||
| on | Of | On | 70,000 points | ||||
| To erase High Score Table: | To erase Game Times: | on | of | oft | No bonus lite | ||
| 1 | Turn control knob Unti 1p line reads PRESS FIRE AND | 1" | Turn control knob until top line reads PRESS FIRE ANO | on | otf | 2iives per game | |
| START 270 ZERO HIGH SCORES. | START 1 TO ZERO TIMES | oo | gt | aimee peters | 8 | ||
| 2, | Press both FIRE and START 2 | 2. | Press both FIRE and START 1 | Soy | jie | ||
| 3, | The word ERASING appears and blinks on the screen until | 3. The word ERASING appears and blinks on the screen until | 1 | OO | 5 lives | per | game |
| the entire table is erased. Wait until the word ERASING | the entire table is erased. Wait until the word ERASING | Off | * | pec | |||
| diseppears before continuing with other tests. | disappears. betore continuing with other tests, | Settings of 4Toggle Switch on Auxiliary PCE (at DIEZ) |
Game difficulty”
| int | Test Pass | 5 | |||||
| frewucton | ee | Tent Fas | ‘off | Off | Medium | $ | |
| 1. | Set seittest | After about 8 sec. | TRAM FAILURE is indicated by a sequence of 1 10 12 Tone and an A dioplayed in top | 8 | Of | On | Easy |
| switch to on (se@ | ond, the monitor ia-___—half of screen. You wil hear a short low tone and See & short flash on the LED ctor | g | on | off | Hard | ||
| Figure 5). Press RE’ | plays the picture be | _pushbutton for each good RAM chip, and a tong high tone accompanied by a tong | 2 | on | oon | Medium | |
| SET on the PCB, or | low. No sounds are | pulse on the start pushbutton fora fling RAM chip. The test stops with the fist fail | 2 | on | Minimum rating range: 1,3, 5,79. | $ | |
| turn power off and | produced, | ing RAM. To restart the sequence, press RESET on the PCB, of power game to off, | On | Minimum rating range tied to high score | |||
| on again | then toon again. Identify the bad RAM chip with the table below. Example: four short | — | — | ||||
| ‘Auoio + | tow tones followed by & long high tone indicales failure of RAM at location MG. | '$ Manufacturer's suggested settings | * Easy—Enemies move slower and one less enemy shot on the | ||||
| peat | SIBLE AND WiFeIne | Bad RAM Chip Location | screen at onetime | ||||
| ROM AT RI | waNCH OF | ‘Long High Tone | ‘on Analog | Vector-Generator PCB | Changing | toggles 1-5 erases the high score table. | Hard-—One more enemy, enemies move faster and 1-4 more |
| ISBAD | Fiala eed | wea | ugieg | foe) | 7 | ‘enemy shots on the screen at one time. | |
| “SF | a | 1st | Ra |
2nd P2
| 3rd | Re | Coin Counter Option Settings | ||
| TOGGLE | ain | Pa | ||
| Toaate | SWITCH 8 | stn | ms | These toggles determine which coin mechanisms activate which counters) |
en Ma _
| cocxtan | D> | n a, | SWITCH ar Liz | 7th | — | a | |||||
| Site | ero | ‘Same | Pon | an | & | "Sate an Ang cor | |||||
| SWITCH AT N19. | Sonnnnae | SWITCH AT OVE | ‘a | Ko | Generator PCB (K10/11) | Two coin acceptors | Tiree coin acceptors | ||||
| ‘Goin: Modes | nooo | faerie iMCUm | oth | Ka | 4 | 3 | 2 | 1 | in the | coin door: | in the coin door:* |
| sTaat 2 | i | 1 encover | ih | 3 | ~ | ——-____- | |||||
| ] | wweew | ‘ath | “4 | On | Off | Both acceptors activate all coin | Left acceptor activates one coin | ||||
| / | ! | counters simultaneously. | Counter, canter and right acceptor | ||||||||
| stant | FIGHT'COIN MECH, ROM FAILURE is indicated by a vertical pair of hexadecimal numbers on the top of the | setivate/SrctTiog doin eoantet::Nor | |||||||||
| FIRE: | ‘screen, The top number indicates the location of the failing ROM(s). Ignore the bottom | for any currently designed 3-mech | |||||||||
| wsecinene’ | LEFT COIN MECH | hexadecimal number in the pair. Identify the bad ROM with the table immediately | in door. |
below.
| DTLITY oti Sen TCH: | Off | On | Both acceptors activate 2. count- | Left and center acceptor activate | |||||
| oc | 1 separate | ‘one coin counter, right | 4 | ||||||
| SLAM SWITCH | Displayed No. | Bad ROM Chip: | tion | PCB | tion | ers | separately. | $$ | Fon pare ac: |
| 8 | a | 2 | 8 | ||||||
| PHOTO ABOVE SHOWS | A | Pt | ae | ||||||
| Mi cane oie | 3 | mnt | SS | of | otf | sotnaccentersactate | count | Let anerand ght acento ct | |
| Fs | tay | Alo Vector: | 3 | 8 | es separately. | sae 2 coin counes separate | |||
| 7 | KI | Generator PCB | aad |
6 a 5 Ht 4 Ft
| 3 | a | On | On | Both acceptors activate all coin | All 3 are same denomination and |
| : | 2 | counters simultaneously. | $§ | they activate all coin counters si | |
| 4 | Ea | multaneously | |||
| ° | Nps | — | — | — |
EAROM, Audio and Math Box Failure are indicated by a: single letter in the center of the display. Identify the failure with the table below.
| Displayed Letter | Failure | PCB Location |
| € | EAROM | 3 (Aux. PCB) |
| Pp | ‘Audio 1 | BIC2 (Aux. PCB) |
| Q | ‘Audio 2 | ‘GiD2 (Aux. PCB) |
| R | RAM | ‘See Ram test above |
M Math Box* *
“If this ROM is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. Math-box failure is explained in TM-195, Tempest Troubleshooting Guide.
2 Activate start, fire, Superzap, SLAM, and coin switches." ‘As switch activates, you'l hear a beep and 0 changes to 1 on the screen. You will not hear a beep and 0 will remain on the screen for the defective switch.
- Slowly rotate en- ‘coder wheel clock: wise and counter. clockwise. A line rotates clockwise ‘around one end point -when you sfowly spin the wheel clockwise. The line rotates counterclockwise when you spin the wheel counterclockwise Rotating line changes direction. Indicates harness wires are incorrectly con: nected or loose, or the encoder whee! is bad.
- Observe the white frame around the outside of the screen. Each frame corner should bbe within Ye-inch of each video display bezel comer. Consult Tempest™ Drawing Package to adjust video pots.
- Activate SLAM switch, ‘A white cross hatch pat texn appears. A character ‘set appears at the bottom of the screen, If display is not centered and symmetrical on the video display, adjust video pots (see Tempest Drawing Package) on the main PCB. If character set is incor rect, check Vector ROMs (see Troubleshooting Guide).
- Activate SLAM switch. Rectangle appears at dis: play edges, shrinks smoothly to about screen size and snaps. back to full size. Horizontal ‘and vertical lines cross in the center of the screen, displaying a large “plus’ sign. Audio VO 1 and 2 al temate to produce four tones. Rectangle abruptly changing size indicates trouble in linear scale cicuity. Lines. not crossing indicate video pot on main PCB needs adjusting (see Drawing Package). No sound indicates failure of an audio amplifier andfor the custom audio chip(s).
- Activate SLAM switch. Tests purple, cyan, yellow, white, green, blue, and red for color and intensity. Dis: plays seven groups of ver tical lines, each with right Tine the brightest and left line the dimmest. Use this pattern for tracking adjustments (see the Color XY Display Mantua),
8 Activate SLAM switch, ‘A checkerboard pattem touches the sides and cor ners of the video display. Rotate the control knob to ‘change color. Use this pattern for purty and convergence adjustments (see Color X-Y Display Mana),
- Activate SLAM switch, ‘A white frame is displayed fon the screen,
- When satisfied with test, set selftest switch to off position.
- Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you are in self-test. ATARI '$ Manutacturer’s suggested settings for games with 1 coin counter. $$ Manufacturer's suggested settings for games with two coin counters, $55 Manufacturer's suggested settings for games with optional second and third coin counters.
- see Drawing Package OP-190 for additional components required for operating the third coin counter.
Game Price Settings
The table below contains the switch settings for those options relating to game price. coin mechanism multipliers, bonus play demonstration and freeze mode. This information is useful if you want to view all 9 levels of play or treeze the action. if you need to temporarily set the Tempest™ game on free play. oF f you have german cot mechanisms im your coor,
To.achieve bonus plays, all coins must be inserted before pressing the start button. If you choose the two play minimum, set toggle 8 at PCB switch assembly L12 to off,
Toggle Settings of 8-Toggle Switch on Tempest ‘Analog Vector-Generator PCB (at N13)
| 1 | 2 | 3 | 4 | 5 | 6 | 7 |
oft off On On
On On on of of On of off
on ott
| On | On | On |
On Ono
| On | Of | On |
On oft
| Of | on | On |
| of | on | oft |
| on | oft | ont |
| of | off | off |
The Demonstration Mode** allows you to choose any level (1-81) in the ready-to play mode and accelerate through the tubes without having to kill the enemies. Freeze allows you to stop the action. The score is zeroed al the end of the game in this mode.
Set the toggles per the table below for the Demonstration Mode. Next, rotate the control knob. You may choose level 1 through 81 during the ready:to-play mode. Press either START but ton to accelerate through the tubes. Press the FIRE button to ‘clear the spikes at the bottom of the tube. To freeze play, set Switch 1 to off
On — ort
| On | —1.coin* for tcredit | $ |
Off 2 cains* for t credit
Right coin mech x 1 $ Right coin mech x 4 Right coin mech x § Right coin mech x 6 Left coin mech x 1 $ Lett coin mech x 2 No bonus coins $ For every 2 coins* inserted, game logic adds 1 more
For every 4 coins" inserted, game logic adds 1 more
For every 4 coins" inserted, game logic adds 2 more
For every 5 coins inserted, game logic adds 1 more
For every 3 coins* inserted, game logic adds 1 more ‘coin*
Demonstration and Freeze Mode**
on On Demonstration Mode Demonstration-Freeze Mode
“in the US, a “coin” is defined as 25°. In Germany a "coin" is OM.
'$ Manutacturer’s suggested settings
VOLUME INCREASE: SELF-TEST TURN CLOCKWISE ‘SWITCH 1.) bad SELF-TEST
‘SWITCH (EURO- PEAN GAMES) VOLUME CONTROL If the operation, maintenance and service manual or
| troubleshooting | guide was not | included | in this |
game when you unpacked it, contact your distributor to get a free copy. (All Atari manuals for coinoperated games also include complete illustrated parts lists.)