Bosconian Parts and Operating Manual (Feb 1982)
Bosconian (Midway Manufacturing Co., 1982) · Parts & Operating Manual · 96 pages · 51 sections · original scan
FEBRUARY, 1982 Game Nos. 550, 555, & 557
No. 550 UPRIGHT
MIDWAYS
LICENSED FROM NAMCO LTD.
Parts and Operating Manual
No. 555 MINI
No. 557 COCKTAIL
MIDWAY MFG. CO. A BALLY COMPANY
10750 W. GRAND AVENUE FRANKLIN PARK, ILLINOIS 60131 USA
Phone: (312) 451-1360 Cable Address: MIDCO Telex No.: 72-1596
Form No. 0550-00300-0000
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
eRe Sse ate BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES
LAMES PEUVENT ETRE INSEREES A FOND SANS ew LAISSER
AUCUNE PARTIE A DECOUVERT.
MIDWAY MFG. CO.
- Suitee You To Use ouR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER MIDWAY GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS. Continental U. S. 800-323-7182 Hlinois Only 1-800-942-0497
COPYRIGHT 1982 © BY MIDWAY MFG. CO. ALL RIGHTS RESERVED.
NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR INTHE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131
Printed In U.S.A.
TECH SERVICES
TABLE OF CONTENTS
DESCRIPTION PAGE
Introduction ........ 66. cece cee ce nett tenn tenet nee n een 1-1
Location and Setup . Inspection .... Installation . Self-Test ..... Game Volume Adjustment Control Option Switch Settings. . Game Operation...... Self-Test Mode . Attract Mode .... Ready-to-Play Mode ... Play Mode Two Player Operation ..
Maintenance and Repair Cleaning ........... Fuse Replacement .. Opening the Control Panel ... Removal of Main Display Glass and T.V. Bezel T.V. Monitor Replacement ................- 23-5 Printed Circuit Board Replacement Opening the Attraction Panel... Coin Door Maintenance
Ilustrated Parts Breakdown No. 550 — Bosconian Upright — Header Fluorescent Light Assy. No. 550 — Bosconian Upright — Header Fluorescent Light Assy. — Parts List No. 550 — Bosconian Upright — Front................ No. 550 — Bosconian Upright — Front — Parts List . No. 550 — Bosconian Upright — Rear Access ..... No. 550 — Bosconian Upright — Rear Access — Parts No. 555 — Bosconian Mini — Front........... No. 555 — Bosconian Mini — Front — Parts List... No. 555 — Bosconian Mini — Rear Access No. 555 — Bosconian Mini — Rear Access — Parts List No. 557 — Bosconian Cocktail — Front............. 4-10 No. 557 — Bosconian Cocktail — Front — Parts List. 4-11 No. 557 -— Bosconian Cocktail — Interior Access.... 4-12 No. 557 — Bosconian Cocktail — Interior Access — Parts List 4-13 Bosconian — Card Rack Assy. w/Boards — All Versions . Bosconian — Card Rack Assy. w/Boards — All Versions — Bosconian — Control Assembly — All Versions..............- 4-16 Bosconian — Control Assembly — All Versions — Parts List Bosconian — Transformer Board Assy. — Parts List . Front Door Assembly — U.S.A. 25¢ ........... Front Door Assembly — U.S.A. 25¢ — Parts List...
iii
TABLE OF CONTENTS (Continued)
DESCRIPTION PAGE
Vv.
vi.
Vil. Technical Troubleshooting .......... 0.00: c eee e cece eee ee cece eee e nee e neste n neta 5-1 Introduction General Suggestions ... Harness Component Troubleshooting Transformer and Line Voltage Problems A Glossary of Microprocessor Terms. Introduction to the Z-80 CPU...... General Purpose Registers .. Arithmetic and Logic Unit (ALU)........ Instruction Register and CPU Control. Z-80 CPU Pin Description
T.V. Monitor Manual. . Introduction ....... Symptom Diagnosis.... Guide to Schematic Symbols Troubleshooting ....... Theory of Operation . Differences Between Monitors . Parts Interchangeability ......... Monitor Schematic —- Wells-Gardner 19” Replacement Parts List — Wells-Gardner 19”. . Monitor Schematic — Electrohome 19” ..... Replacement Parts List — Electrohome 19” ... Monitor Schematic — Electrohome 13” ....... Replacement Parts List — Electrohome 13” ...
Schematics and Wiring Diagrams Wiring Diagram — Upright .. Wiring Diagram — Mini .. Wiring Diagram — Cocktail. . Power Supply PCB — Component Layout... Power Supply PCB — Schematic ....... Rapid Fire Board — Component Layout . Rapid Fire Board — Schematic .... CPU. Board — Component Layout . CPU Board — Schematic.......- Video Board — Component Layout Video Board — Schematic......... Filter Board — Component Layout. Filter Board — Schematic .........
FIGURE
1 Assigned point values 2 Location of serial number, interlock switch, on/off switch and major sub-assemblies 3 Major sub-assemblies (cont. from Fig. 2) 4 Interlock switch operation 5 Location of option switches and volume control 6 Option switch settings ................. 0. eee 7 identification of “on screen” graphics during play 8 Location of fuses ........... cece e cece eee eee 9 Removing control panel — Upright & Mini games. 10 Opening the Cocktail game..... . 1 Removing control panel — Cocktail game 12 Removing display glass — Upright game.
- Removing display glass — Mini game 14 Removing top glass — Cocktail game . 15 Replacing monitor — Upright game. 16 Replacing monitor — Mini game.. 17 Opening the Cocktail game... 18 Replacing monitor — Cocktail game 19 Power supply replacement ......... 20 Removing Video & CPU boards from card rack . 21 Opening the attraction panel — Upright game.. 22 Replacing fluorescent starter — Upright game.. 23 Replacing fluorescent tube mounting bracket — Upright game .. 24 Replacing speaker — Upright game 25 Opening the attraction panel — Mini game . 26 Replacing Speaker — Mini game 27 Removing and replacing coin acceptors 28 Opening the metal coin acceptor ... 29 Lubricating the metal coin acceptor. 30 Opening the plastic coin acceptor .. 31 Changing the plastic coin acceptor to accept TABLE OF FIGURES
Bosconian
IMPORTANT NOTE
DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and Ii of this manual completely. It will not take more than a few minutes and it may be very helpful.
I. Introduction
BOSCONIAN is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCKTAIL TABLE”. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to fly their space fighter(s) through the game course. If you have purchased the Cocktail Tabie model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn. When playing this game, you are the pilot of a space fighter stationed in deep space to defend your solar system against the on-coming BOSCONIAN conquerors and their space station worlds. Your mission is to destroy as many of the enemy ships and space stations as possible. These invaders arrive in convoys. They will attack you and attempt to runinto you while flying back and forth across the screen. They will engage your fighter either singly or in ATTACK FORMATIONS to defend their space station worlds from you. The BOSCONIAN space station worlds have several defences of their own to hinder you. They keep the areas around them filled with Cosmo-Mines, eject Space Mines when you approach, fire Missiles, and through a mysterious power, are able to attract Asteroids and keep them floating in their immediate vicinity.
1-1 Your space fighter is provided with a long range scanner which can pick up and track the BOSCON- JAN home space station worlds and the Attack Formations they send out to destroy you. However, your scanner’s sensitivity does not enable it to pick up and track single BOSCONIAN Ships, Missiles, Space Mines of any type, or Asteroids. As your skill level increases, the number and direction of attackers coming at you at any one time and the speed with which they attack, is gradually increased; plus, their attack patterns become more and more complex while their aim gets better. Bonus ships are awarded to you periodically throughout the game as you reach or pass certain preselected point values. Each enemy Ship, Missile, etc. has an assigned point value as listed in Figure 1.
Major NewFeatures
Your BOSCONIAN game has several new features among which is the ability of your space fighter to fire both forward and backward at the same time, giving you greatly increased fire power, and the option to start a new gameat the same level that your last fighter was destroyed
Game Objective
The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills and destroying as many of the enemy as you can. As you do this, each following convoy of attackers will be harder to destroy.
OBJECT DESTROYED POINT VALUE
ASTEROID 10 POINTS COSMO-MINE 20 POINTS I-TYPE MISSILE 50 POINTS P-TYPE MISSILE 60 POINTS E-TYPE MISSILE 70 POINTS SPY SHIP MYSTERY CANNON ON ENEMY BASE SPACE STATION 200 POINTS ENTIRE ENEMY BASE SPACE STATION 1500 POINTS ENTIRE I-TYPE MISSILE ATTACK FORMATION 500 POINTS ENTIRE P-TYPE MISSILE ATTACK FORMATION 1000 POINTS ENTIRE E-TYPE MISSILE ATTACK FORMATION 1500 POINTS
Figure 1 Assigned point values
1-2
Il. Location and Setup
INSPECTION
- Remove the game from its shipping crate.
- Inspect the entire outside of it for any signs of damage. © Any scratches? Dents? Cracks?
- Any broken controls?
- Any broken glass or plastic? Just look it over closely and make a note of any signs of damage.
- Remove the shipping cleats from the bottom of the cabinet. 4, Install the four levelers, one at each corner of the cabinet. © Level the cabinet.
- Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2. ® Also check to make sure all plug-in connectors on the wire harness are firmly seated.
¢ Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure
- These connectors are also keyed. The P.C.B.'s will only go into them one way without being damaged.
- Note the location of the game's serial number. See Figure 2. © Check all major subassemblies to be sure they are mounted securely. These are cailed out in Figures 2 & 3. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Transformer board assembly.
- Make a note of any problems that can’t be easily corrected,
- Call your distributor and/or service man about your problem list. INSTALLATION 1, Location requirements: Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz Temperature: 32° to 100°F (0° to 38°C) Humidity: Not over 95% relative Space required: Upright 25” x 29” (63 x 73cm) Mini 20" x 24” (50 x 60cm) Cocktail 32" x 22” (81 x 55em) Game height: Upright 70” (175cm) Mini 61" (153cm) Cocktail 29” (73cm)
. Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
. Interlock and power ON/OFF switches. See Figure 2. © To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOKS NOT include the coin door in the Upright and Mini models). When any access door is opened, the interlock switch installed there turns off all power to the game. e Check each operation. interlock switch for proper
SERIAL SERIAL NUMBER NUMBER
TV. MONITOR
INTERLOCK \ y a. INTERLOCK SWITCH SWITCH
‘TRANSFORMER BOARD ASSY (NOT SEEN) TRANSFORMER BOARD ASSY (NOT SEEN) POWER SUPPLY UPRIGHT PCB
| SERIAL NUMBER | F | TV. MONITOR |
(MAY BE LOCATED a i \
| ON ANY CORNER) | 4 | TRANSFORMER |
BOARD ASSY CONTROL
| PANEL | : | ; |
| PLAYER 1 | aa | CONTROL |
PANEL PLAYER 2
POWER SUPPLY PCB
INTERLOCK “——~on/orF SWITCH SWITCH . LOCATED UNDER (INSIDE DOOR) TABLE ON PLAYER 2 SIDE COCKTAIL
Figure 2 Location of serial number, interlock switch, on/off switch & major subassemblies
CONTROL PANEL
UPRIGHT
Figure 3 Major subassemblies (cont. from FIG. 2)
After checking the line voltage in your areaand determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 2. Turn thegameon and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on.
2-3 After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 4.
Figure 4 Interlock switch operation
SELF-TEST Your new game will Self-Test itself to see if ithas any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the games speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).
GAME VOLUME ADJUSTMENT CONTROL. See Figure 5. The game volume control pot is located on the CPU board. The other board is the video board. There is only one pot. For adjustment, it may be reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you will have to open the table top to reach it. To make the sounds louder, turn the pot clockwise as you face it (~~). To make the sounds less loud, turn the pot counterclockwise as you face it (7).
OPTION SWITCH 6J
OPTION SWITCH 6K
Z al I OPTION SWITCH SETTINGS To change the option switch settings, you DO NOT have to take the CPU board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you do have to open the table top to reach them. When changing any options, ALWAYS put the game into the Self-Test mode, make your changes, check the results on the monitor screen, take the game out of the Self-Test mode, and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The option switch settings and what they will make the game do are shown in Figure 6. See Figure 5 for _ option switch locations.
VOLUME CONTROL
o—™. LOUDER
Figure 5 Location of option switches and volume control
BOSCONIAN
OPTION SWITCH SETTINGS
DIP SWITCH 6J
1 PLAYER GAME SWiH1 SW#2 SW#3 SWH4 SWHS SWH6 SWH7 SWHB PRESS THE 1 PLAYER START BUTTON 1, 2, 3, or 5 FIGHTERS OFF NOT USED 2 PLAYER GAME PRESS THE 2 PLAYER START BUTTON 1, 2,3, OR 5 FIGHTERS EACH
1 PLAYER GAME PRESS THE 1 PLAYER START BUTTON 1, 2, 3, OR 5 FIGHTERS
4 PLAYER GAME WITH 3, 5, 7, OR 11 FIGHTERS PRESS THE 2 PLAYER START BUTTON
DIFFICULTY LEVEL SETTINGS — “B” IS THE EASIEST AND “C” IS THE MOST DIFFICULT
SW#1 SW#2 SW#3 SW#H4 SWHS SWHE SWH7 SWHB
| " — STANDARD LEVEL OF DIFFICULTY | OFF OFF | NOT | ||
| RANK “B” | — EASIEST LEVEL OF DIFFICULTY | OFF | ON | USED |
| RANK “C” — HARDEST LEVEL OF DIFFICULTY | ON | OFF | NOT | |
| RANK “AUTO” — (MEASURES PLAYERS SKILL LEVEL) | ON | ON | USED |
SW#1 SW#2 SW#3 SWH4 SWHS SWHE SWH7 SWHB NO GAME CONTINUATION FEATURE. ON NOT PLAYER(S) MAY CONTINUE GAME FROM PRESENT OFF USED ROUND AFTER LAST SHIP HAS BEEN DESTROYED. THIS COSTS ADDITIONAL CREDITS. PLAYER(S) SCORE(S) ARE RETURNED TO ZERO — “O”.
GAME PROVIDES SOUND IN ATTRACT MODE NOT GAME DOES NOT PROVIDE SOUND IN ATTRACT MODE USED
FREEZE VIDEO (MONITOR PRESENTATION STOPS MOVING) ON NOT MONITOR OPERATES NORMALLY OFF USED
COIN COUNTER
SW#1 SW#2 SW#3 SWiH4 SWHS SWHE SWH7 SWHB ONE WAY NOT ON TWO WAY USED OFF
Figure 6 Option switch settings
FREE PLAY 4 COINS 3 COINS 2 COINS 2 COINS 1 COIN 1 COIN 1 COIN 1 CREDIT 1 CREDIT 1 CREDIT 3 CREDITS 3 CREDITS 2 CREDITS 1 CREDIT
BEGAN WITH 1, 2 OR 3 FIGH
1st SHIP 2nd SHIP. AND EVERY
1st SHIP 2nd SHIP AND EVERY
1st SHIP 2nd SHIP
ist SHIP 2nd SHIP. AND EVERY
1st SHIP 2nd SHIP AND EVERY
1st SHIP 2nd SHIP AND EVERY
1st SHIP 2nd SHIP TERS
50000
10000 50000 50000
30000 100000 100000
15000 70000 70000
20000 70000 BOSCONIAN
OPTION SWITCH SETTINGS
DIP SWITCH 6K
COINS PER CREDIT
BEGAN WITH 5 FIGHTERS
1st SHIP 30000 2nd SHIP 120000
1st SHIP 2nd SHIP
1st SHIP 2nd SHIP AND EVERY
1st SHIP 2nd SHIP
ist SHIP 2nd SHIP AND EVERY
1st SHIP 2nd SHIP 100000
ist SHIP 30000 2nd SHIP 120000 AND EVERY — 120000
NO BONUS SHIPS GIVEN WITH THIS SETTING SW#1 SW#2 SW#3 SW#4 SWHS SWHE SWH7 SWHB ON ON OFF OFF ON ON OFF OFF ON ON ON ON OFF OFF OFF OFF
SW#1 SW#2 SW#3 SW#4 SWHS SW#H6 SWH7 SWHB
ON ON OFF
DETERMINES NUMBER OF SPACE FIGHTERS PLAYER BEGINS GAME WITH:
1 SPACE FIGHTER 2 SPACE FIGHTERS 3 SPACE FIGHTERS 5 SPACE FIGHTERS
Figure 6 Option switch settings (cont’d.)
Game Operation
BOSCONIAN is a one or a two player game with a color T.V. monitor. The game gives a display which has all the parts shown in Figure 7.
PLAYER’S FIGHTER
“P” TYPE MISSILE The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.
HIGH SCORE
PLAYER 1 SCORE
PLAYER 2 SCORE
RADAR SCREEN
PLAYER'S FIGHTER
SPACE STATION
FIGHTERS IN RESERVE ROUND NO.
Figure 7 Identification of “on screen” graphics during play
SELF-TEST MODE
The Self-Test mode is a special mode for checking the game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.
You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on. Test switch is located inside coin door under coin meter. When this is done, the game will react as follows:
- First, you will see a moving multicolored pattern appear on the screen.
- Immediately following this, a rightside up test display is shown On the monitor screen, This will remain until you set the Self-Test switch back to the “OFF” position. This test display is shown below.
SELF-TEST DISPLAY AND BOARD LOCATION COORDINATES RAM OK or (a number and a letter, i.e. 1L, 3H, etc.) ROM OK or (a number, i.e. 0, 2, etc.) UPRIGHT or (TABLE) *1 COIN *1 CREDIT *3 SHIPS RANK *A (B, C, AUTO) SOUND 00 (01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) 1ST BONUS *20000 PTS 2ND BONUS *70000 PTS *AND EVERY 70000 PTS
- = switch selectable
2-7
DISPLAY
RAM OK RAM 1L RAM 1H RAM 2L RAM 2H RAM 3L RAM 3H RAM 4L RAM 4H RAM 5L. RAM SH RAM 6L RAM 6H
ROM OK ROM 0 ROM 1 ROM 2 ROM 3 ROM 4 ROM 5 ROM 6 All RAMs are good. RAM located on CPU PC board at position 2N is bad. RAM located on CPU PC board at position 2N is bad. RAM located on CPU PC board at position 2N is bad. RAM located on CPU PC board at position 2N is bad. RAM located on Video PC board at position 1E is bad. RAM located on Video PC board at position 1E is bad. RAM located on Video PC board at position 1E is bad. RAM located on Video PC board at position 1E is bad. RAM located on Video PC board at position 1H is bad. RAM located on Video PC board at position 1H is bad. RAM located on Video PC board at position 1H is bad. RAM located on Video PC board at position 1H is bad.
All ROMs are good. ROM located on CPU PC board at position 3N is bad. ROM located on CPU PC board at position 3M is bad. ROM located on CPU PC board at position 3L is bad. ROM located on CPU PC board at position 3K is bad. ROM located on CPU PC board at position 3J is bad. ROM located on CPU PC board at position 3H is bad. ROM located on CPU PC board at position 3E is bad. DESCRIPTION
- If a bad ROM or RAM chip is found by the game's internal check system during the Self-Test, the game indicates this to you by showing the location code of the bad chip(s) in place of the letters “OK”. The above table translates the chip location codes into actual positions on either the Video or the CPU P.C. Boards.
- “RANK” is°a difficulty setting, with “RANK B". being the least difficult level of play and “RANK C”. being the most difficult level of play. “RANK AUTO”; at this setting the game measures the player's skill level and progressively gets harder as the player gets better. See the “OPTION SWITCH SETTINGS” table.
. To check “SOUND” (the game has 20 different sounds):
- Move the controller to the right momentarily and release it — “SOUND” number changes from “00” to “01” and you hear sound “01”.
- Press any button or activate the coin switches and sound “01” will change to sound “02” and it is heard.
- Repeat Step 2 with a different button or switch, etc. and — “SOUND 02” changes to “SOUND 03” and it is heard — and so on.
. To check your game function switches and buttons (coin counter switches, FIRE button, 1 PLAYER and 2 PLAYER buttons): activate each one while the game is in the Self-Test mode. You should hear. a different game sound for each tivation..If you do not hear it, the switch/button ‘either not working, miswired, or disconnected. Check it out thoroughly.
. When finished with the Self-Test mode, slide the Self-Test switch back to the “OFF” position. Across hatch pattern appears on the monitor screen for about 2 seconds. © If you wish to keep this test pattern on the monitor screen for further use, slide Self-Test switch back tothe “ON” position after the cross hatch appears and before it disappears. @ When finished with the cross hatch pattern, set the Self-Test switch to the “OFF” position. ¢ Normal game functions will now return to the monitor screen.
ATTRACT MODE
- The Attract mode starts: © Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.)
- After a Self-Test has been completed. (Performing a Self-Test sets the credits in the game's memory to zero “0”.) ¢ After a play has been finished, the score was not high enough to put the game into the High Score/Initial mode, and there are no more credits left in the game’s memory. ¢ After the High Score/Initial mode when there are no more credits left in its memory.
- In the Attract mode, the game will give the following displays centered on the monitor screen:
DISPLAY 1
z & COSMO-MINE 20 PTS.
ASTEROID _ he pe 10 PTS & 4 SPY SHIP MYSTERY 60 PTS ae
E-TYPE 70 PTS
DISPLAY 2
2-9 « The above display and the one that follows give the point values assigned to the different things that can be destroyed by your space fighter.
6000 iuPp SCORE TABLE.
CONDITION
CANNON 200 PTS
DISPLAY 3a
SCORE TABLE
ENEMY BASE 1500 PTS
DISPLAY 3b
e The fourth display in the attract mode sequence shows simulated game play.
© The next display in the series lists the five highest scoring individuals, “THE LIST OF SPACE FIGHTERS”, that have played the game to date.
wt ert ap? 720° B7200. THE List OF
SPACE FIGHTERS. CONDITION
29000
DISPLAY 5
@ No matter where the game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will hold this display on the monitor screen until the “1 PLAYER” or the “2 PLAYER” start button is pushed.
PUSH START BUTTON 4 PLAYER ONLY
NO BONUS FOR ANI EVERY. 000 PTS
CREDIT, 4
® 19814 MIDWAY MFG. co.
READY-TO-PLAY MODE
1. The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game. . The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed. . Inthe Ready-To-Play mode, the game will give the above display centered on the monitor screen. . If no START button is pressed, the game wiil hold the above display on the screen indefinitely. PLAY MODE
1, The Play mode begins when either the “1 PLAYER” or the “2 PLAYER” start button is pressed. “PLAYER ONE” — “READY” is displayed centered on the screen.
- The Play mode ends when all of your space fighters have been destroyed. When this happens, “GAME OVER’ is written across the center of the monitor screen.
- The game is made up of convoys of invading aliens. You, as defender, try to destroy as many convoys as you can. They are hard, tricky fighters. Your task will not be easy! Just remember that when shooting at the space station hub to take out the whole station, the missile launching doors MUST be at least part way open in order for your shots to be able to destroy the entire space station. Or, if you destroy all six Cannons on the space station rim, the entire space station will go up with the destruction of the sixth Cannon.
- The convoys are displayed one at a time on the long range scanner to the right of the screen. They are made up of BOSCONIAN Space Station worlds which are surrounded by Cosmo-Mines and Asteroids. These space stations send out three different types of missiles to try to biow you out of space. They are: “I-TYPE”, which are purple in color; “P-TYPE”, which are silver-blue in color; and “E-TYPE”, which are red in color. The longer you are in a particular “ROUND” (ROUND 1, ROUND 2, etc.), the more missiles the enemy space stations will send out after you. (What “ROUND” you're in is indicated at the lower right hand corner of the screen.) You MUST destroy every BOSCONIAN space station wortd in a particular “ROUND” to advance to the next one.
There are also special Attack Formations made up of five missiles each which will appear continuously throughout the game. If they are completely destroyed, bonus points will be awarded as follows:
OBJECT DESTROYED ENTIRE I-TYPE MISSILE ATTACK FORMATION 500 POINTS ENTIRE P-TYPE MISSILE ATTACK FORMATION ENTIRE E-TYPE MISSILE ATTACK FORMATION 1000 POINTS
1500 POINTS
The Rounds in which the different Attack Formations will appear are as follows:
ROUND NUMBER VEHICLE TYPE
P I Pp Pp E E P E
P E
P E E E E NOARBR
ROUND 18 AND BEYOND — REPEATS VEHICLE SEQUENCE FOUND FROM ROUND 12 THROUGH 17.
These Attack Formations are lead by one missile that is the same shape as the other four but is a slightly different color. If you shoot this “lead — or
- control missile”, the Attack Formation will break up and go in different directions.
When you destroy the last space station of a convoy, the screen gives the following display centered on the monitor screen:
PLAYER ONE READY
The number of the next ROUND is displayed in the lower right corner of the screen, the next convoy of BOSCONIAN space station worlds appears in the long range scanner at the right side of the monitor screen, your space fighter appears at the center of the screen, and play begins. As you destroy more convoys, the attacks on you become faster, are in a more rapid succession, and follow trickier flight patterns. For instance, they will try to trap you in a cross fire, or with your back to a mine field, etc. You've really got to watch them closely. When the enemy happens to destroy one of your fighters, assuming you have at least one reserve fighter left, the words “PLAYER ONE” — “READY” appear centered on the monitor screen BEFORE play begins again. When the enemy destroys your fast fighter, the words “GAME OVER” are displayed centered on the monitor screen. (AT THIS POINT, SEVERAL DIFFERENT THINGS CAN HAPPEN DEPEND- ING ON WHETHER THE “GAME CONTINUA- TION FEATURE” HAS BEEN SELECTED.)
“GAME CONTINUATION FEATURE” HAS NOT BEEN SELECTED:
If your score was the highest one of the five best scores, the game will tell you this by putting the following display on the screen.
37200 2UP
CONDITION
After this display, the game will go into the High Score/Initial mode immediately. If your score was not the highest of the day, but was still one of the “BEST 5”, the game will go directly to the High Score/Initial mode presentation. If your score is not high enough to cause the game to go into the High Score/tnitial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).
“GAME CONTINUATION FEATURE” HAS BEEN SELECTED:
The game will act in the same manner as stated above EXCEPT IN THE CASE WHERE your score is not high enough to cause the game to go into the High Score/Initial mode and there are no more credits left in its memory. In this case, it will give the following display centered on the monitor screen:
TQ CONTINUE GAME
IMSERT COIN AND
PUSH START BUTTON
BEFORE TIME COUNT ENTERS ©. TIME 15
If there are ONLY enough credits left in the game's memory for a ONE PLAYER GAME, the above message is modified to read as follows:
TO CONTINUE GAME
PUSH START BUTTON i PLAYER ONLY
Re TIME COUNT ENTERS 0. TIME 4 {f there are at least enough credits left in the game's memory for a TWO PLAYER GAME, the above message is modified to read this way:
TO CONTINUE GaME
BUSH START BI 1 OR 2 PLAYERS.
BEFORE TIME COUNT ENTERS ©. TIME-14
If you decide to exercise any of the above options BEFORE the 15 second time limit runs out, your score will be set BACK to ZERO “0”, the ROUND number that you were in when your last space fighter was destroyed will REMAIN THE SAME, and play will begin in the same sequence as it has for all previous games. If you do not decide to exercise any of the above options BEFORE the 15 second time limit runs out, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still Credits left in its memory). Also, if you do decide to play another game AFTER the 15 second GAME CONTINUATION time limit has run out, you will be starting at ROUND 1 again with your score at ZERO “0”.
HIGH SCORE/INITIAL MODE
In the High Score/Initial mode the game gives a display which looks like the following:
uprens FO
SCORE CONDITION 7O :
ScoRE
20000: 20000. 20000 Z0000.
When in the High Score/initial mode, there are three “A”’s under the top “NAME” heading on the screen. The first “A” is red and flashing on and off. The other two “A” ’s are white. Farther down the screen under the “BEST 5” heading, your score has been entered in bright green and the space for your initials is blank. All other scores are white. By moving the controller stick to the right, the flashing letter can be made to sequence forward through the alphabet: “A”, “B”, “C”, “D”, etc. By moving the controller stick to the left, the flashing letter can be made to sequence backward through the alphabet: “2”, “Y", “X”, “W”, etc. When you reach your initial, release the controller and push the FIRE button. Your initial is frozen in place and appears in the biank space opposite your score at the same time. If you do not wish to put your initials opposite your score, just press the FIRE button three times. Three “A” ’s will appear opposite your score. After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To- Play mode (if there are still credits left in its memory). Most of the above holds true in the “2 PLAYER” mode also, But there are a few minor differences. TWO PLAYER OPERATION The Upright, Mini, and Cocktail Table models all have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however: 1, In the Upright and Mini models, the players must take turns at the controls.
- In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When it is not your turn, your set of controls will have NO effect on the game.)
- Your turn lasts unti! the enemy blows up your space fighter. At this point, the game will do one of several things depending on whether or not the destroyed fighter was your last or if you still have others remaining in reserve.
FIGHTER DESTROYED — FIGHTERS REMAINING
IN RESERVE © The attack stops. e Next, the “ROUND” changes to the “ROUND” number the other player is in, it displays “PLAYER __” — “READY” while what's left of the other player’s convoy appears on the long range scanner at the right of the screen. ¢ Play begins for the other player.
FIGHTER DESTROYED — NO FIGHERS REMAIN- ING IN RESERVE © Game displays “GAME OVER”. e Next, if your score was the highest one of the five best scores, the game will tell you this by putting the congratulatory display on the screen. After this display, it will go into the High Score/Initial mode immediately. If your score was not the highest of the day, but was still one of the “BEST 5”, the game will go directly to the High Score/Initial mode presentation. After this, the “ROUND” changes to the “ROUND” number the other player is in, the game will display “PLAYER __” — “READY” while what's left of the other player's convoy appears on the long range scanner at the right of the screen and play begins for the other player. e If your score was not high enough to cause the game to go into the High Score/Initial mode, the game will display “PLAYER __” “READY” while what's left of the other player's convoy appears on the long range scanner at the right of the screen and play begins for the other player.
Ill. Maintenance and Repair
Your BOSCONIAN game needs certain types of maintenance to keep itin good working order. Clean, well maintained games attract players and earn more profits. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.
CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors; hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. {f you wish, special coin machine cleaners that leave No residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CAN NOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.
FUSE REPLACEMENT This game contains several fuses located as shown in Figure 8.
- UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Mech. Panel and the Power Supply Board. . MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Mech. Panel and the Power Supply Board. nN . COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Mech. Panel and the Power Supply Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual.
See the T.V. Monitor Manual (available on request from your distributor or monitor manufacturer) and/or the TV. Troubleshooting Section of this manual for information on these fuses.
FUSES LOCATED ON TRANSFORMER BOARD & POWER SUPPLY
Figure 8 Location of fuses
OPENING THE CONTROL PANEL. See Figure 9.
- UPRIGHT MODEL: « The control panel is held in piace by three
- MIN| MODEL: The control panel is held in place by two latches, one on the left side, one on the right side, and one on the front center. They are spring loaded to provide constant positive pressure On their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. © To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. e To reinstall the control panel, reverse this procedure.
UPRIGHT latches, one on the right side and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. To reinstall the control panel, reverse this procedure.
Figure 9 Removing control panel — Upright & Mini games
3-2
CLAMPS
Figure 10 Opening the Cocktail game
- COCKTAIL TABLE MODEL: ¢ Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 10.
Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open as indicated in Figure 10. REMOVE SCREWS (2)
Remove the screws which secure the control panel in place. See Figure 11. ¢ To remove the contol panel(s): Disconnect it from its cabling. The control panel is now free and can be
- SCREWS UNDER SHELF
removed. e To reinstall the contro! panel, reverse this Figure 11 Removing control panel — Cocktail procedure. game
3-3
REMOVAL OF THE MAIN-DISPLAY- GLASS AND/OR THE T.V. BEZEL ASSEMBLY
- UPRIGHT MODEL: See Figure 12. 2. MINI MODEL: See Figure 13.
Turn the power to the game off and remove the rear access door. Remove the screws from the glass support bracket and lift it out the back of the cabinet. Grasp the main-display-glass in the top center, lift up slightly and pull it out the rear of the cabinet. Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clanps may be removed. To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure.
REMOVE BRKT
REMOVE DISPLAY GLASS FROM REAR OF GAME
Figure 12 Removing display glass —Upright game
© Turn the power off to the game and remove the control panel. « Remove the screws which secure the glass clamping plate. ¢ Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. © By putting your finger in the hole in the middle of the main-display-glass support, you can liftit up and out. e Remove the screws which secure the T.V. bezel assembly and lift it out.
e Reverse this procedure to reinstall the T.V. bezel assernbly and the main-display-glass.
DISPLAY
CLAMPING PLATE
Figure 13 Removing display glass — Mini game
- COCKTAIL TABLE MODEL: See Figure 14.
CAUTION: High voltages may exist in any television loose. i i :
unit, even with the power disconnected. Use The monitor mounting channels slide on top of EXTREME CAUTION and do not touch electrical and against two metal guides mounted to the cabinet’s right and left sides. The monitor is arts or the T.V. yoke area with your hands or with P z y w removed by sliding it out the back of the metal objects held in your hands! binet. See Fi 15 In addition, BE SURE TO USE HEAVY GLOVES ee = ans when handling the monitor. You could cut your To reinstall the T.V. monitor, reverse this hands on the metal T.V. chassis without such Procedure. protection. After replacing the T.V. monitor, be sure to run the game Self-Test.
REMOVE 4 BOLTS
REMOVE GLASS CLAMPS (8)
Figure 14 Removing top glass — Cocktail game Figure 15 Replacing monitor — Upright game
3-5
- MINI MODEL: See Figure 16. Turn the power off to the game. Open the rear access door. Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Mini Model” procedure. With the removal of only four nuts, the T.V. monitor will be ioose.
REMOVE 4 BOLTS
Figure 16 Replacing monitor — Mini game
CLAMPS
The monitor is removed by supporting it and pulling straight back as shown in Figure 16. To reinstall the T.V. monitor, reverse this Procedure. After replacing the T.V. monitor, be sure to run the game Self-Test.
- COCKTAIL TABLE MODEL: See Figure 18. Turn power off to the game. Open the coin box door and release the two latches indicated in Figure 17.
id latch is very the HIGH VOLTAGE on the m
e Once the latches are released, unhook them from their latch plates. e Grasp the table top at “A” and open it as indicated in Figure 17.
Remove the screws which hold the table top glass clamps in place. © Remove the table top glass. « Lift out the T.V. bezel assembly.
Figure 17 Opening the Cocktail game
Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE.
Remove the screws holding the T.V. monitor chassis to the “L” by the door hinge(s). See Figure 18. Close the Cocktail Table top and re-latch it. Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 18. Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. To reinstall the T.V. monitor, reverse this procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. After replacing the T.V. monitor, be sure to run the game Self-Test.
REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP
REMOVE 4 SCREWS (2 EACH SIDE)
Figure 18 Replacing monitor — Cocktail game PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT
- UPRIGHT MODEL: See Figure 19. ¢ Turn the power to the game off. Unlock and open the rear access door.
- Disconnect the video board from all its cabling. Disconnect the CPU board from ail its cabling. Slide the P.C.B. clamps to one side, remove the P.C.B.’s from the card rack and take them out the back of the cabinet. Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 19, and slide it out the back of the cabinet. To reinstall the above P.C.B.’s, reverse this procedure.
- MINI MODEL: See Figure 19. Turn the power off to the game. Unlock and open the rear access door. Disconnect the video board from all its cabiing. Disconnect the CPU board from all its cabling. Slide the P.C.B. clamps to one side, remove the P.C.B.'s from the card rack and take them out the back of the cabinet. Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 19, and slide it out the back of the cabinet. To reinstall the above P.C.B.’s, reverse this procedure. COCKTAIL TABLE MODEL: See Figure 19. © Turn the power off to the game. © Open the cabinet: Open the coin box door and release the two latches indicated in Figure 17.
Once they're released, unhook them from their latch plates. ¢ Grasp the table top at “A” and open it as indicated in Figure 17.
POWER SUPPLY P.C.B.
REMOVE THIS REMOVE THIS SUPPORT TO SUPPORT TO SLIDE P.C.B. OUT SLIDE P.C.B. OUT
REMOVE (2) _— SUPPORTS TO | | SLIDE P.C.B. UP a Del ~ )
UPRIGHT
POWER SUPPLY P.C.B.
= COCKTAIL
Figure 19 Power supply replacement
¢ To remove the power supply board. See Figure 19. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure.
¢ To remove the video and CPU boards. See Figure 20. Disconnect the video board from all its cabling. Disconnect the CPU board from all its cabling. Slide the P.C.B. clamps to one side, remove the P.C.B.’s from the card rack and lift them out the top of the cabinet. Figure 20 Removing Video & CPU boards from To reinstall the video and CPU boards, reverse card rack this procedure.
3-8
OPENING THE ATTRACTION PANEL
- UPRIGHT MODEL: See Figure 21. © Turn the power to the game off.
- Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 21. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. See Figure 21. To reinstall the attraction panel, reverse this procedure. ¢ The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
- Replacing the fluorescent tube starter. See Figure 22. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. e Replacement of the fluorescent tube mounting bracket assembly. See Figure 23. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything.
eo™ ¥, TURN TO REPLACE To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. Replacing the speaker. See Figure 24. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker.
REMOVE SCREWS AND BRKT ON TOP
SLIDE ATTRACTION PANEL UP
Figure 21 Opening the attraction panel — Upright game
FLUORESCENT TUBE STARTER
Figure 22 Replacing fluorescent starter — Upright game
SCREWS FOR REMOVE SPEAKER FROM LIGHT BRKT FRONT OF GAME
Figure 23 Replacing fluorescent tube mounting Figure 24 Replacing speaker — Upright game bracket — Upright game
PULL REMOVE SCREWS FROM 2. MINI MODEL: See Figure 25. ATTRACTION TOP & BOTTOM BRACKETS * Turn the power off to the game. PANEL (USE SPECIAL WRENCH ¢ Remove the screws from the to| p and bottom of AWAY FROM SHIPPED WITH YOUR the formed attraction panel. GAME ) e Remove the formed attraction panel by pulling
it straight away frorn the cabinet. This exposes the attraction panel light bulbs and their mounting board. ¢ To service the light bulbs and their mounting board: Turn the power to the game back onso you can see which bulbs are burnt out. Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. Figure 25 Opening the attraction pane! — Mini To reinstall the above removed items, reverse game this procedure.
3-10
© To replace the speaker. See Figure 26. COIN DOOR MAINTENANCE Be sure the power is off to the game. METAL COIN ACCEPTOR MECHANISMS Disconnect the speaker from its cabling. Remove the nuts and bolts securing the Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned. speaker. Slide the speaker out through the rear access 1. Make sure the power to the game is off. doer . 2. Unlock and open the coin door. To reinstall the speaker, simply reverse this i -
procedure. 3. fi coin acceptor mechanism as shown
in Figure 27.
- THE COCKTAIL TABLE MODEL HAS * Push down on the two spring loaded latches. HO BACH-EI ATTRAC TIONIPANEL ¢ While holding the latches down, pull the top of the coin acceptor mechanism toward you. © Release the latches and lift out the coin acceptor mechanism.
- Clean the magnet of all foreign particles. See Figure 28. e This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) © Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: e Place the coin acceptor in boiling water for about ten minutes.
- Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the it. REMOVE a ; ; . SPEAKER ¢ Rinse the coin acceptor in clean boiling water. FROM REAR e Dry the coin acceptor thoroughly by using OF GAME filtered compressed air to blow it dry.
- To lubricate the coin acceptor: e Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 29. © Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
To REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS TO REPLACE
PULL MECHANISM out PUSH MECHANISM IN
Figure 27 Removing and replacing coin acceptors
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 27. © Place the two pegs at the coin acceptor's base into their retaining slots.
- Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
PLASTIC COIN ACCEPTOR MECHANISMS
The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door. GATE OPEN
3. Remove the coin acceptor mechanism(s) as Cre ARGNET
shown in Figure 27. BY DRAGGING A
- Push down on the two spring loaded latches. SCREWDRIVER BLADE ® While holding the latches down, pull the top of ACROSS SURFACE the acceptor mechanism toward you. ¢ Release the latches and lift out the mechanism. Figure 28 Opening the metal coin acceptor
3-12
APPLY POWDERED GRAPHITE HERE
SQUEEZE PINS TOGETHER TO UNLOCK
Figure 30 Opening the pl:
3-13
- Squeeze the two pins indicated in Figure 30 together to open the mechanism and break it down into its three basic parts. ® Clean the mechanism in hot soapy water. It never rusts. e Rinse the mechanism in clean hot water and allow it to dry. e Reassemble the mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: Paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 27. © Place the two pegs at the coin acceptor’s base into their retaining slots. © Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
“a
SWING BOTH GATES OPEN
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
lastic coin acceptor
MAGNET
ACCEPTOR CAN BE SET TO ACCEPT U.S, QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
eS
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
—<
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 31 Changing the plastic coin acceptor to accept American or Canadian quarters
3-14

This page is a drawing, shown as the original scan.
NO. 550 — BOSCONIAN UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY.
NO. 550— BOSCONIAN UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0508-00103-0000 FLUORESCENT BRKT. 0017-00003-0043 18” COOL WHITE FLUOR. LAMP 0017-00021-0005 FLUORESCENT LOCKS (2 REQ’D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ'’D.) 0017-00003-0412 FLUOR. STARTER HOLDER W/WIRE LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ'’D.) 0017-G0104-0009 #6 EXT. WASHER (4 REQ'D.) 0017-00003-0019 FLUOR. STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ'D.) A508-00017-0000 FLUORESCENT CABLE ASSY. A961-06042-0000 LINE FILTER ASSY. — NOT SHOWN
NO. 550— BOSCONIAN UPRIGHT — FRONT
4-2
NO. 550— BOSCONIAN UPRIGHT — FRONT — PARTS LIST
PART NO. ORDER BY PART NUMBER ONLY
DESCRIPTION
0550-00901 -0OXF 0537-00903-0057 0508-00104-00XF 0017-00101-0138 0017-00009-0522 A508-00007-0000 0017-00009-0393 0017-00003-0259 0017-00101-0136 0017-00103-0061 0508-00900-0000 0508-00905-0000 0508-00901-0000 0017-00101-0017 0550-00900-00XF 0508-00108-0000 0017-00101-0027 0550-00903-0000 0550-00904-0000 A550-00009-0000 0508-00115-0000 0961-00115-00XF 0017-00191-0620 0017-00103-0061 0017-00009-0033 0017-00101-0141 0550-00101-0100 0550-00101-0200 0555-00901 -0000 0550-00902-0000 A557-00006-0000 0017-00042-0256 0017-00032-0093 0017-00103-0054 0017-00032-0051 A090-00300-07BK 0090-00002-04BK 0017-00101-0121
0935-00906-0100 0017-00102-0048 0017-00103-0026 DECORATIVE HEADER PLEX! — 23” x 8-15/16" x 3/16” GLASS CHANNEL — 7-5/8" LG. (2 REQ’D.) UPPER/LOWER HEADER RETAINER (2 REQ'D.) #8 x 5/8 TORX TAMPER RESISTANT BLK. SCR. (6 REQ’D) LONG ARM KEY T-20 (FOR ABOVE SCREW) HEADER FLUORESCENT LIGHT ASSY. SPEAKER GRILLE — BLACK W/SLOTS 6" x 9” SPEAKER 8 OHM, 7W. #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) 19" T.V. BEZEL T.V. PLEXI-GLASS (GRAYLITE #31) — 17-3/8" x 13-1/4" x 1/8” PLEXI-GLASS CLIPS (4 REQ'D.) #6 x 1/2 SLT. HEX HD. BLK. SCR. (4 REQ’D.) MAIN VIEWING GLASS — 23” x 21-1/8" x 3/16" GLASS STOP BRKT. — CABINET REAR #8 x 3/4 SLT. HEX HD. M.S. (3 REQ’D.) DECAL — SIDE DECAL — FRONT STRIKE TO CONTROL PANEL ASSY. CENTER CONTROL SHELF LOCK BRKT. STRIKE (2 REQ’D.) #8-32 x 1/2 CARRIAGE BOLT (10 REQ’D.) #8-32 HEX NUT W/SEMS (12 REQ'D.) LATCH CLAMP (3 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (6 REQ'D.) CONTROL SHELF MTG. BRKT. — RIGHT CONTROL SHELF MTG. BRKT. — LEFT LOCATING PIN (4 REQ’D.) CONTROL SHELF OVERLAY — DECORATIVE CONTROL ASSY. PUSH BUTTON ASSY. — RED (2 REQ’D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) §/8-11 PAL NUT (2 REQ’D.) SMALL RED PUSH BUTTON SWITCH (2 REQ'D.) U.S.A. 25¢ DOUBLE COIN DOOR ASSY. LARGE BLACK DOUBLE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) KICK PLATE — 23" LG. 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.)
4-4 NO. 550 — BOSCONIAN UPRIGHT — REAR ACCESS
NO. 550 — BOSCONIAN UPRIGHT — REAR ACCESS — PARTS LIST ORDER BY PART NUMBER ONLY PART NO. DESCRIPTION
A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY. 0894-00916-0000 RECESSED HAND LIFT (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCREW (12 REQ'D.) 0017-00003-0339 ELECTROHOME — 19" COLOR DUAL SYNC HORIZ. MFG. MONITOR (OR) 0017-00003-0418 WELLS-GARDNER — 19" COLOR DUAL SYNC HORIZ. MTG. MONITOR 0550-00100-0000 MONITOR RAIL (2 REQ'D.) 0017-00102-0006 1/4-20 x 3/4 SQR. NECK BOLT (4 REQ’D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ'D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT, HEX HD. MLS. (8 REQ’D.) 0555-00901-0000 LOCATING PIN (4 REQ’D.) 0508-00900-0000 TV. BEZEL A088-00015-0000 INTERLOCK SWITCH & BRKT. ASSY. A082-90420-B000 | + 5V/4A POWER SUPPLY P.C. ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) 0624-00902-0300 P.C. SUPPORT BRKT. — 2-1/2" LG. 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2" LG. 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (10 REQ'D.) 0017-00104-0037 #8 FLAT WASHER (10 REQ’D.) A550-00017-0000 CARD RACK W/P.C. BOARDS ASSY. A961-00007-0000 CASTER ASSY. (2 REQ’D.) 0961-00109-0000 WHEEL BRKT. (2 REQ’D.) 0017-00042-0255 PLASTIC WHEEL (2 REQ'D.) 0894-00702-00XF SHAFT (2 REQ’D.) 0017-00100-0037 3/8" E-RING (2 REQ’D.) A950-00004-0000 COIN BOX ASSY. A950-00006-0000 COIN BOX CRADLE ASSY. 0950-00105-0000 COIN BOX COVER 0950-00104-0000 COIN BOX HANDLE 0950-00101-0000 COIN DEFLECTOR (2 REQ’D.) 0950-00900-0000 LARGE PLASTIC CASH BOX 0017-00101-0142 1/4-20 x 1-3/8 RND. HD. BOLT BLK. (4 REQ'’D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ'D.) A866-00049-0000 LINE CORD ASSY. ADDITIONAL PARTS LIST A550-00013-0000 TRANSFORMER BOARD ASSY. A097-00008-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILLE (4 REQ’D.) 3010-03003-0000 GROUNDING CLIP A508-00024-0000 VIDEO SIGNAL CABLE ASSY. A508-00034-0000 AUDIO ADAPTER CABLE ASSY. A508-00035-0000 VIDEO SIGNAL ADAPTER CABLE ASSY. A550-00011-0000 CONTROL SHELF CABLE ASSY. A550-00016-0000 MASTER CABLE ASSY. A508-00026-0000 COIN DOOR CABLE ASSY. A508-00014-0000 HIGH VOLTAGE CABLE ASSY. AS08-00015-0000 LOW VOLTAGE CABLE ASSY. A082-91410-A000 RAPID FIRE P.C. BOARD ASSY. 0017-00101-0018 #6 x 3/4 SLOT HEX HD. SCREW (4 REQ’D.) 0508-00106-0000 TV. BEZEL MTG. BRKT. (2 REQ’D.) 0508-00108-0000 MAIN VIEWING GLASS STOP BRKT. 0017-00101-0027 #8 x 3/4 SLT. HEX HD. M.S. (3 REQ’D.)
4-5
NO. 555 — BOSCONIAN MINI — FRONT
4-6
NO. 555 — BOSCONIAN MINI — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0555-00900-00XF HEADER DISPLAY PANEL 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (8 REQ'D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A555-00007-0000 INSERT DISPLAY ASSY. 0017-00031-0030 WEDGE BASE LIGHT SOCKET (5 REQ’D.) 0017-00003-0219 #194 LAMP 14V., .27A. (5 REQ’D.) A514-00015-0000 INSERT DISPLAY CABLE ASSY. 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS 0017-00003-0259 6" x 9” SPEAKER — 8 OHM, 7W. 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0555-00902-00XF MAIN GLASS — 17-13/16" x 14-13/16" x 3/16” 0537-00903-0056 GLASS CHANNEL — 14-1/2" LG. (2 REQ’D.) A555-00016-0000 GLASS CLAMPING PLATE ASSY. 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCR. (2 REQ’D.) A555-00005-0000 T.V. BEZEL ASSY. 093 1-00903-0000 T.V. BEZEL 0934-00905-0000 PLEXI-GLASS (TINTED) A961-00026-0000 BEZEL MTG. BRKT. ASSY. A555-00015-0000 OVERLAY/CONTROL PLATE ASSY. 0555-00102-0000 CONTROL SHELF PLATE 0555-00903-0000 CONTROL SHELF DECORATIVE OVERLAY 0017-00101-0620 #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) A555-00013-0000 CONTROL SHELF CABLE ASSY. 0555-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0555-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 LOCATING PIN (4 REQ’D.) 0961-00115-00XF STRIKE (2 REQ’D.) 0017-00009-0033 LATCH CLAMP (2 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. MS. (8 REQ'’D.) A557-00006-0000 CONTROL ASSEMBLY 0017-00042-0256 PUSH BUTTON ASSY. — RED (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 0017-00103-0054 5/8-11 PAL NUT (2 REQ’D.) 0017-00032-0051 SMALL RED SWITCH BUTTON W/HARDWARE (2 REQ'D.) A090-00300-07BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. 0090-00002-04BK LARGE BLACK DOUBLE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) A508-00026-0000 COIN DOOR CABLE ASSY. 0935-00906-0400 KICK PLATE — 17-15/16" LG. 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)
4-7
NO. 555 — BOSCONIAN MINI — REAR ACCESS
NO. 555 — BOSCONIAN MIN! — REAR ACCESS — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO.
0017-00003-0259 0017-00003-0340
0017-00003-0396
A926-00012-00XF 0017-00101-0141 0555-00100-0000 0017-00102-0066 0017-00104-0014 0017-00103-0018 A088-00015-0000 A090-00300-07BK A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A082-90420-B000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0141 0017-00104-0037 A550-00017-0000 A555-00009-0000 A088-00013-0000 A866-00049-0000
A097-00008-0000 0017-00009-0490 A514-00011-0000 A555-0001 1-0000 A555-00012-0000 A508-00034-0000 A508-00035-0000 A508-00024-0000 3010-03003-0000 A082-91410-A000 0017-00101-0018 DESCRIPTION
6” x 9" SPEAKER 8 OHM, 7W. ELECTROHOME — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR T.V. MTG. BRKT. ASSY. #8 x 11/16 UNSLOT. HEX HD. M.S. (2 REQ'D.) MONITOR MTG. BRKT. (2 REQ'D.) 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ’D.) INTERLOCK SWITCH & BRKT. ASSY. DOUBLE ENTRY COIN DOOR ASSY. COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ’D.) LARGE PLASTIC COIN BOX 1/4-20 x 1-3/8 RND. HD. BOLT (4 REQ'D.) 7/8” DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ’D.) 5V/4A POWER SUPPLY P.-C. ASSY. P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 2-1/2" LG. P.C. SUPPORT BRKT. — 6-1/2" LG. #8 x 11/16 UNSLOT. HEX HD. M.S. (10 REQ’D.) #8 FLAT WASHER (10 REQ'D.) CARD RACK W/P.C. BOARDS ASSY. TRANSFORMER BOARD ASSY. ON/OFF SWITCH & BRKT. ASSY. LINE CORD ASSY.
ADDITIONAL PARTS LIST
BACK DOOR LOCK ASSY. 5-5/8" SQR. VENT GRILL — BACK DOOR (4 REQ'D.) HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. MASTER CABLE ASSY. AUDIO ADAPTER CABLE ASSY. MONITOR SIGNAL ADAPTER CABLE ASSY. VIDEO SIGNAL CABLE ASSY. GROUND CLIP RAPID FIRE P.C. BOARD ASSY. #6 x 3/4 SLOT. HEX HD. SCREW (4 REQ'D.)
NO. 557 — BOSCONIAN COCKTAIL — FRONT
4-10
NO. 555 — BOSCONIAN COCKTAIL — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0017-00009-0499 0557-00903-0000 0775-00104-00XF 0017-00101-0117 0508-00905-0000 0508-00901 -0000 0017-00101-0017 0557-00900-0000 A557-00007-0100 A557-00007-0200 0017-00009-0393 0017-00003-0187 0017-00101-0136 0017-00103-0061 A090-00300-07BK 0090-00002-02BK 0017-00101-0121 COVER GLASS — 32” x 22” x1/4" ARTWORK UNDERLAY GLASS CLIPS (8 REQ'D.) #8 x 5/8 PHIL. TRS. HD. SCR. (16 REQ’D.) T.V. PLEXI-GLASS (GRAYLITE #31) — 17-3/8" x 13-1/4" x 1/8” PLEXI-GLASS MTG. CLIPS (4 REQ’D.) #6 x 1/2 SLT. HEX HD. SCR. (4 REQ'D.) T.V. BEZEL CONTROL SHELF ASSY. — PLAYER #1 CONTROL SHELF ASSY. — PLAYER #2 BLACK SPEAKER GRILLE W/SLOTS (3 REQ’D.) 6" x 9” SPEAKER 8 OHM, 9W. #8-32 x 1-1/4 CARRIAGE BOLT (12 REQ’D.) #8-32 HEX NUT W/SEMS (12 REQ'D.) U.S.A. 25¢ DOUBLE COIN DOOR ASSY. LARGE BLACK DOUBLE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.) 0017-00102-0048 0017-00103-0026
NO. 557 — BOSCONIAN COCKTAIL — INTERIOR ACCESS
4-12
NO. 555 — BOSCONIAN COCKTAIL — INTERIOR ACCESS — PARTS LIST
ITEM PART NO.
0017-00003-0428 ORDER BY PART NUMBER ONLY
DESCRIPTION
WELLS-GARDNER — 19” COLOR DUAL SYNC VERT. MTG. MONITOR MONITOR MTG. BRKT. ASSY. (2 REQ’D.) #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ’D.) #8 FLAT WASHER (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) 1/4-20 x 1/2 SLT, HEX HD. BOLT (6 REQ’D.) 1/4-20 x 1" UNSLT, HEX FLAT HD. BOLT (6 REQ’D.) 7/8" DISH WASHER (8 REQ'D.) STRIKE (2 REQ’D.) #10 x 3/4 SLT. HEX HD. M.S. (4 REQ’D.) LATCH CLAMP (2 REQ'D.) — NOT SEEN #8 x 11/16 UNSLOT HEX HD. SCREW (4 REQ'D.) 2-1/2" HINGE (2 REQ'D.) #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) T.V. BEZEL CONTROL PANEL (2 REQ’D.) DECORATIVE OVERLAY — PLAYER #1 DECORATIVE OVERLAY — PLAYER #2 #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ'D.) #6 x 1/4 PHIL. TRS. HD. SCR. (10 REQ'D.) BOTTOM PAN (2 REQ'D.) CONTROL ASSY. (2 REQ'D.) CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2 RED PUSH BUTTON ASSY. (2 REQ'’D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ'D.) 5/8-11 PAL NUT (2 REQ'’D.) SMALL RED BUTTON SWITCH W/HARDWARE (2 REQ'D.) — PLAYER #1 PANEL ONLY CONTROL PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2 SLT. HEX HD. MS. (16 REQ'D.) LIGHT SHIELD (2 REQ'’D.) WEDGE BASE LAMP SOCKET (4 REQ'D.) #194 LAMP 14V., .27A. (4 REQ'D.) #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ'D.) 6" x 9" SPEAKER 8 OHM, 9W. CARD RACK W/P.C. BOARDS ASSY. TRANSFORMER BOARD ASSY. 5V/4A. POWER SUPPLY P.C. ASSY. P.C. SUPPORT BRKT. — 12” LG. P. C. SUPPORT BRKT. — 2-1/2" LG. P.C. SUPPORT BRKT. — 6-1/2" LG. (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (14 REQ’D.) #8 FLAT WASHER (14 REQ’D.) A557-00004-GOXF 0017-00101-0642 0017-00104-0031 0017-00103-0061 0017-00102-0002 0017-00102-0052 0017-00104-0014 0921-00107-00XF 0017-00101-0769 0017-00009-0033 0017-00101-0141 0017-00009-0514 0017-00101-0628 0017-00101-0639 0017-00103-0061 0557-00900-0000 0557-00102-00XF 0557-00902-0100 0557-00902-0200 0017-00101-0620 0017-00103-0061 0017-00101-0341 0510-00101-00XF A557-00006-0000 A557-00014-0100 A557-00014-0200 0017-00042-0256 0017-00032-0093 0017-00103-0054 0017-00032-0051
0930-00104-0000 0017-00101-0025 0930-00904-0000 0017-00031-0044 0017-00003-0219 0017-00101-0555 0017-00003-0187 A550-00017-0000 A557-00010-0000 A082-90420-B000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0141 0017-00104-0031
NO. 555 — BOSCONIAN COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)
PART NO. ORDER BY PART NUMBER ONLY
DESCRIPTION
A775-00013-0000 0151-00081-0000 0775-001 10-O0XF 0749-00106-00XF 0017-00101-0347 0017-00104-0009 0017-00103-0005 0017-00101-0026 A082-91410-A000 0017-00101-0018 A088-00013-0000 A927-00019-0000 A962-00004-0000 A962-00005-0000 0962-00101-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 A088-00014-0000 0927-00907-0000 A557-00013-0000 A510-00011-0000 A557-00012-0000 A508-00026-0000 A510-00014-0000 A508-00034-0000 A508-00035-0000 A927-00005-0000 A866-00049-0000 ADDITIONAL PARTS LIST
FAN ASSEMBLY 4" FAN FAN PLATE VENT SCREEN #6-32 x 1/2 R.H.M.S. (4 REQ'D.) #6 EXT. WASHER (4 REQ’D.) #6-32 HEX NUT (4 REQ’D.) #8 x 5/8 SLT. HEX HD. M.S. (4 REQ'D.) RAPID FIRE P.C. BOARD ASSY. #6 x 3/4 SLOT. HEX HD. SCREW (4 REQ'D.) ON-OFF SWITCH & BRKT. ASSY. COIN BOX ASSY. COIN BOX COVER ASSY. COIN BOX SIDE CHANNEL ASSY. — SHORT COIN BOX SIDE CHANNEL — SHORT #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) #8 WASHER (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) INTERLOCK SWITCH & BRKT. ASSY. HIGH VOLTAGE SHIELD — FORMED MASTER CABLE ASSY. HIGH VOLTAGE CABLE ASSV. LOW VOLTAGE CABLE ASSV. COIN COOR CABLE ASSY. VIDEO SIGNAL CABLE ASSY. AUDIO SIGNAL ADAPTER CABLE ASSY. VIDEO SIGNAL ADAPTER CABLE HIGH BASE LEG KIT ASSY. — OPTIONAL LINE CORD ASSY.
BOSCONIAN — CARD RACK ASSY. W/BOARDS — ALL VERSIONS
BOSCONIAN — CARD RACK ASSY. W/BOARDS — ALL VERSIONS— PARTS LIST
ORDER BY PART NUMBER ONLY
(TEM PART NO. DESCRIPTION
A084-91412-B550 CPU BOARD ASSY. A084-91413-B550 VIDEO BOARD ASSY. A935-60015-0000 HOLDER PLATE & STOP ASSY. (2 REQ’D.) 0017-00009-0478 NYLON GUIDE (4 REQ’D.) 0935-00103-0000 SIDE SUPPORT (2 REQ’D.) 0935~-00102-0000 MOUNTING BRACKET (2 REQ’D.) 0017-00101 -0096 #6 x 3/8 SLT. HEX HD. SCR. (14 REQ’D.) A084-91414-A550 FILTER BOARD ASSY. — MOUNTS ON TO CPU BOARD — NOT SHOWN 0508-00116-0100 P.C. SUPPORT BRKT. — RIGHT — NOT SHOWN 0508-00116-0200 P.C. SUPPORT BRKT. — LEFT — NOT SHOWN
BOSCONIAN — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST
BOSCONIAN — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
A932-00022-0000 BALL & SHAFT ASSEMBLY 0017-00100-0025 1/4" E-RING 0921-00702-0000 STOP SPACER 0921-00902-0000 SLIDE PLATE SPOT WELD ASSEMBLY #8-32 x 1" CARRIAGE BOLT (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ'’D.) A557-00005-0000 0017-00101-0637 0017-00103-0061 0932-00902-0000 GROMMET 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. M.S. (10 REQ'D.) 0962-00904-0000 SLEEVE 0017-00101-0527 0020-00202-0000 A932-00009-0000 A921-00009-0000 0927-00908-0000 0921-00700-0000 #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) SWITCH PLATE (4 REQ’D.) SWITCH ASSEMBLY (4 REQ'D.) STOP PLATE & SWITCH BRKT. ASSY. WEAR PLATE ACTUATOR
BOSCONIAN — TRANSFORMER BOARD ASSY. — PARTS LIST (NO PHOTOGRAPH)
PART NO. DESCRIPTION
MT00-00082-0000 TRANSFORMER — 115/115V. —- UPRIGHT & MINI MT00-00087-0000 POWER TRANSFORMER — 120/240V. — UPRIGHT & MINI MT00-00085-0000 TRANSFORMER — 115V., 50HZ — COCKTAIL ONLY MTO00-00091-0000 SHIELDED TRANSFORMER — 115/220V. — COCKTAIL ONLY 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) 0017-00103-0008 #8-32 HEX NUT (4 REQ’D.) 0017-00101-0741 #8 x 11/16 UNSLOT. HEX HD. SCR. (15 REQ’D.) 0720-00001-0300 3 POSITION FUSE CLIP ASSY. — UPRIGHT & COCKTAIL 0720-00001-0200 2 POSITION FUSE CLIP ASSY. — MINI ONLY 0720-00001-0100 1 POSITION FUSE CLIP ASSY. 0017-00003-0004 SLO-BLO FUSE - 2A., 250V. (2 REQ'D.) 0017-00003-0002 SLO-BLO FUSE — 1/2 A., 250V. — COCKTAIL & UPRIGHT 0017-00003-0217 SLO-BLO FUSE — 2-1/2A., 125V. A508-00037-0000 2 LEAD XFRMR BRD. FILTER ASSY. 3010-13106-0000 TERMINAL STRIP 0017-00021-0370 MALE CONNECTOR — 5 PAIR 3000-17246-0100 GROUND STRAP — COCKTAIL 3000-17246-0500 5-1/2" GROUND STRAP — MINI 3000-17246-0700 20” GROUND STRAP — UPRIGHT & MINI 3000-17246-0800 23" GROUND STRAP — COCKTAIL 3000-17246-0900 48" GROUND STRAP — UPRIGHT 3000-17246-1000 36" GROUND STRAP — MINI & COCKTAIL
4-17
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
0090-00002-02BK 0017-00101-0121 A090-00073-02BK 0017-00101-0123 0017-00007-0019 0017-00101-0552 0090-00117-03XF A097-00005-0000 A097-00006-0000 0090-001 28-00XF 0017-00005-0041 A090-00095-0000 0090-001 26-01XF 0017-00101-0525 A090-00096-0000 0090-00903-9500 0090-00143-00XF 0017-00003-0219 0017-00031-0048 0017-00104-0002 0017-00103-0084 A090-00057-0000 0017-00101-0124 0017-00032-0051 0017-00032-0007 0017-00072-0034 0090-001 73-0000 A090-00082-0000 A090-00087-0000 0010-00134-0000 0010-00181-0000 0017-00007-0083 0090-00129-00XF 0090-00167-00XF 0093-00155-00XF 0017-00100-0018 A090-00088-0000 A090-00085-0000 0017-00005-0003 0017-00005-0211 0017-00005-0214 A090-00064-0000 0017-00101-0099 0090-00162-00XF 0017-00005-0203 0017-00005-0195 0010-00599-0000 0017-00007-0132 A090-00059-0400 0017-00101-0698 A090-00077-0000 OWRMBNANAWN= FRONT DOOR ASSEMBLY — U.S.A. 25¢
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
DOUBLE ENTRY COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) DOUBLE ENTRY COIN DOOR W/DRESS PLATE #8 x 1/4 UNSLOT. HEX HD. SCREW (4 REQ’D.) KEY HOOK #6-32 x 1/4 CARRIAGE BOLT (4 REQ’D.) COIN ENTRY PLATE — 25¢ (2 REQ’D.) DOOR LOCK & KEY W/SCREW & NUT (OR) DOOR LOCK & KEY W/SCREW & NUT DOOR TILT SWITCH BRKT. DOOR CAM DOOR TILT SWITCH SWITCH BACK-UP PLATE #5-40 x 9/16" PHIL. HD. M.S. (2 REQ’D.) DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 25¢ WINDOW (2 REQ'D.) COIN PLEX RETAINER 12 VOLT LAMP — G.E. #1895 (2 REQ’D.) BAYONET SOCKET W/BRKT, (2 REQ’D.) #6 SPLIT LOCK WASHER (8 REQ'D.) #6-32 HEX NUT W/SEMS (4 REQ’D.) COIN METER #6 x 1/4 UNSLOT. HEX HD. SCR. (8 REQ’D.) PUSH BUTTON SWITCH SLIDE SWITCH STEEL OVAL HD. RIVET COIN COUNTER MTG. BRKT. TEST SWITCH & BRKT. ASSY. (ITEMS 23 THRU 25) COIN CHUTE & TOP ASSY. (2 REQ’D.) SPRING SPRING 1/8 x 1-5/8 ROLL PIN PIVOT POST PIVOT LEVER REJECT LEVER E-RING REJECT LEVER ASSY. (2 REQ'D.) (ITEMS 30 THRU 33) COIN ACCEPTOR FRAME ASSY. (2 REQ’D.) COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) (OR) COIN ACCEPTOR W/ANT! STRING DEVICE (2 REQ'’D.) (OR) COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) ANTI-PENNY DEVICE #6 x 1/4 SLT. HEX HD. M.S. (2 REQ’D.) COIN SWITCH MTG. BRKT. COIN SWITCH CHUTE COIN SWITCH COIN SWITCH WIRE PUSH-ON RING COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) #4-40 x 3/4 SLT. RND. HD. M.S. (2 REQ’D.) COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)
V Technical Troubleshooting
Harness Component Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Typical problems falling in this category are coin and credit problems, power problems and failure of individual features.
5-1 NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player’s coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. if not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. \f you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.
5-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then. connect your VOM across the terminats of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. {f a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. Ifso, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.
CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.
EPROM — erasable, programmable, read-only memory, Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production. ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration ({VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MS! up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devicesa computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:
- :The Z-80 is fully software compatible with the popular 8080A CPU. . Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages, Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts: 1, CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to
contain instructions and in most cases data that is to
be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic. ny
General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. Insystems where fast interrupt response is required, one set of general purpose registers and an accumulaior/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The contro! sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.
| ™ | 27 | 30 | Ay |
= AY
| REQ | ud | —a | |
| SYSTEM _/ ioRG | cid | | » a, | |
| CONTROL | 55 | 21 | 34 |
|} A,
| wr | 7 | ——— |
36 Ae AFsH = 28_| va,
38 ADDRESS
As
| — | _ | ‘a | BUS |
| mart | =<“ | Z-80 CPU | A |
Ao
| —_ | 24 | 1 |
| 7 | —4t 9 | +» a, |
| cpu | ws | 2 |
CONTROL [> av
| int | = —8 a | ——— |
| nmi | |= | L* » a, |
->—_ A, Reset —S y CPU BUSRQ mal BUS | controt )°YS** ~ 4 pee, A
| 6 | 6 | E | >, |
W
| wv | aa | DATA | |
| «ND | ———> | D, | BUS |
9 > —s Z-80 PIN CONFIGURATION o
Ao-Ais (Address Bus) Tri-state output, active high. Aj-A;5 constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allowthe user to directly select up to 256 input or 256 output ports. Ap is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.
Dy-D, (Data Bus) Tri-state input/output, active high. Dp-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.
My, (Machine Cycle one) ___ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle.
MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1oRQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid /O address for a I/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) __ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an |/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) _ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or !/O device. RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP's to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.
INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 0066. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI.
RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register |= 00x
- Set Register R =00n
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all controi ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated.
BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm puil-up resistor to +5 volts to meet all clock requirements.
z0pUOW-_ ‘A’L IA NOA YNVHL iNOA dT3H OL AQWaY GNVLS SHOLNGIYLSIG HNO GNV J4VLS HNO “SHAdVd SAWVD YNOA HLIM GaCIAOdd YASWNN 33u4 TIOL SHL LV ANVdWOO SDNIENLOVANNVW AVMGIN YO HOLNEIYLSID HNOA LOVLNOO ASV31d ‘SNOILSAND JAVH TULS GNV NOILOAS SIHL HDNOYHL AV3Y" NOA JI “HOLINOW ‘A’L SAWV9 YISHL ONIYIVdSY ONV SNILOOHSATISNOYL NI 3AYD3d SOINOYLO313 NV LNOHLIM ASOHL CIV OL GAGNALNI S| GNV YANNVW ONVLSHSGNN OL ASV NV NI C101 SI NOILOAS SIHL NI GANIVLNOO NOILVWHOSNI SHL ‘S.LON SSV31d
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Color T.V.
Color T.V Monitor
Introduction: (How to use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. if you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!
if you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.
If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings
6-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
- Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
- Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). e Bad yoke. e Bad vertical output section. e Open fusible resistor in vertical section. Bad height control. Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). e Bad yoke. e Open width coil. e Open part in horizontal output section. Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal syne off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the probtem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).
6-2 10.
11.
12.
13.
14.
15.
16.
17.
18.
19. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.
Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.
Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.
No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).
No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.
No high voltage; check: A. For AC input to the “flyback”. B. Horizontal deflection stages. C. Flyback transformer. D. Yoke. E. Power supply.
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
23. . Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.
B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
- Can't adjust purity or convergence:
A. Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interferring. —. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN'T MATTER)
SVT WL INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
VL
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR Te COLLECTOR - BASE ————— BASE ————- EMITTER ad EMITTER ———
NPN TRANSISTOR PNP TRANSISTOR
' VA
VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)
+ +
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
hg = GROUND
6-4
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors.
- Resistors.
- Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
6-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It's better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube.
To maintain the safety and performance of the monitor, aiways use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off ali of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the bright- Ness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC. wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping
6-6 through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or none atall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later. THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz).
The sync is amplified by a sync ampiifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color informatiori is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION — After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assmebled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” or 19” color monitor uses transistors for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit IC501 for its sync section. The idea is all the same. The output to the vertical amplifying transistors for all monitors must be a sawtooth wave form, sort of like a bunch of pyramids, racing to the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set. The amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.
6-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Again, Wells Gardner uses transistors for the horizontal oscillator, and Electrohome uses the other side of 1C501. Still, the effect is the same. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillators frequencies must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU!! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.
COLOR CIRCUITS The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There only two, one for the red and one for the green. The
blue doesn't have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don't show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.
PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voitage coming from the power supply. To find out, check the emitter on TR502 of the Wells Gardner monitors; or the emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Wells Gardner = 127VDC. Electrohome = 120VDC
The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, the GO7-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.
THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuits work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and Circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with, assuming you can’t find the brand name written on it anywhere, is to see if there are two circuit boards rising up from the chassis toward the picture tube neck. In other words, they stand up, or are perpendicular to the chassis, with a black plastic bracket holding them in place. This is a description of a Wells Gardner monitor. They use separate boards for main chunks of circuitry. Therefore, you have a “power board” (the power supply), an “interface board” (the interface section), and a “horizontal/ vertical board” (for the deflection circuitry). Still, there are a few parts on the chassis, but most can be found on the board. An Electrohome monitor has no separate boards, except for the neck board, and just has a flat chassis.
Another good way to determine which monitor you have is to check the transistor call out numbers that are printed on the chassis next to the part. For instance, on the neck board, one of the color output transistors is TR401. if you look through the schematics or the parts lists, you will find TR401 in the Wells Gardner literature. On the other hand, the neck board transistor may say X101. X101 can be found in the Electrohome literature. So, all Wells Gardner transistor call outs begin with TR, and Electrohome transistor call outs start with an “X”.
Parts Interchangeability Some parts can be interchanged on all of the monitors. Here are the rules:
- You CAN swap the voltage regulator TR502 or X01 on any Wells Gardner or Electrohome 19 inch monitor. You CAN NOT swap the voltage regulator on the 13 inch Wells Gardner or Electrohome (G07-902) since the Electrohome uses an integrated circuit for the power supply.
- You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance.
- You CAN swap any capacitor between monitors that has the same capacitance, and voltage rating.
- PICTURE TUBES: Due to the fact that “ELECTROHOME” is now (October, 1981) using a picture tube with an internal shield, these picture tubes can be used in EITHER “WELLS GARDNER’ or “ELECTRO- HOME” monitors. However, a “WELLS GARDNER" picture tube can ONLY be used in a “WELLS GARDNER” monitor. It will not function properly if installed in an “ELECTROHOME” monitor. The picture purity will be off.
- You CAN NOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-904) monitor “flyback”. looks identical to the 19 inch Electrohome (G07-904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTERCHANGEABLE!
- You CAN change any of the parts between the GO07-904 and G07-907. They're essentially the same monitor except that the GO7-907 has a vertically mounted picture tube If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part. ‘
VPRE ORI 28c 174! 2sci740, ve ey ORVE, Vout 11 TR: r A304 FeCTTIO TRIOS 2Saagq TRIO? TOOTS WELLS-GARDNER
VERTICAL RASTER POSITION ADJUSTMENT
CENTER Dow
- yosi-00087-Aolz
VAMP 2sci7ao 3 2861740. Thi Sem
v.ouT Bay sw FERS. "ee 188s Se + 19"COLOR MONITOR SCHEMATIC DIAGRAM
INTERFACE BOARD P317
rz03 tk 1a,3%
fo coe) i.
ut of
veoe FAY
- yc peor)
Decavesing 1s1980
x602
e604
28¢: 1708 fe) 280108. 28Cia54 Bsc 1693 2sauze 2snasq ESCi740, 2sciass 23anrs asczeaz 1 8383 2) Bir 2.2 1ROF Vp PROTECTOR ARR 230 TR3S4 25A825 vam OF 2scirag /ASeiMS_2SA10ie Senne Z\ 25¢ 1740, To #201 ole Ff cow bE or os
wete “L rgror® C62 iseoy © RUDIO/ POWER say H BOARD Sean redid a | MYT] osce MP Feeimns (pS
HOR OSC apps ip gee tras) lat owe ? vert HOR asaess/2sasee 2s me in Bee / 2565 eaage wo 4g thgse 28el 120 /Z5E> gears S076
R502 2sc 1106 2sc asa HORI, RASTER POSITION ADV,
T7or Wy UNIT +70/~ 4703 tro ‘a70 Van 8% 0%
e208
nate ans | we 30 150 aM 398 aw, 8% 0M, 8%
7 cas zee NECK Board [MS70G] (°] TOTO MM UNIT = —— CRT igvTP22 4 >
SERVICE TIP
K4625A, K4626A, K4675A — 5816
6-10
VERT/HOR BOARD (MT/QJ) NECK BOARD (MS/QG)
| Ref. No. | Part No. | Description | Ret. No. | Part No. | Description | Part No. | Description | Rel. No. | Part No. | Description | ||||
| RESISTORS | CAPACITORS (CONT.) | RESISTORS | ||||||||||||
| R301 | 203X6500-628 | 820 Ohm, + | 6313 | 203X0025-087 | 47 uF, 50V Electrolytic | ” | ||||||||
| A302 | 203X6500-902 | 12k Ohm, = | 315 | 203X0015-082 | 10 uF, 25V Electrolytic | bpd | Poaceoeghed | Lae Ohm 2 62 ew Carbon | C403 | 202X7000-247 | 1000 pF, SOV, 10% Ceramic | |||
| R303 | 203X6500-927 | 15k Ohm, = | 316 | 203X1100-220 | 3300 UF, 50V, + 10% Mylar | acs | Soaxes00 709 | 18k Ohm # 5% | BW Carbon | 404 | 202X7110-019 | 1500 pF, 2kV' + 10% Ceramic | ||
| R304 | 203X6500-886 | 10k Ohm, + | 317 | 202X8000616 | 100 pF, 50V, * 10% Ceramic | Rape | 303x6800-447 | 450 Ohm = 5% 1/8W Carbon | C405 | 202X7150-018 | 100 pF, 12kV, + 10% Ceramic | |||
| R305 | 203X6501-241 | 330k Ohm, * 5%, 1/8W Carbon | 351 | 202X7000-281 | 1500 pF, 50V, + 10% Ceramic | Hore | 203X6500-481 | 220 Ohm # 5% t/8W Carbon | C408 | 202X7050-483 | 01 uF, 500V, + 10% | Ceramic | ||
| R306 | 203X6500-645 | 1k Ohm, * 5%, | 1/8W Carbon | 352 | 202X7000-247 | 1000 pF, 50V, + 10% Ceramic | aoe | 203X6500-447 | 150 Ohm | 5% V/8W Carbon | ce | a0eeT 10 O18 | 1500 pF, 2kV = 10% | Ceramic |
| R307 | 203X6500-689 | 1.5k Ohm, * 5%, 1/8W Carbon | C383, | 203X1100-573 | 0.022 uF, 50V, = 10% Mylar | nor | 50sxes00608 | 270 Ohm. | 5% | BW Garbo | 408 | 202X8000-550 | Ceramic | |
| R309 | 203X6500-724 | 2.2k Ohm, * 5%, 1/8W Carbon | C355 | 203X1100-858 | 0.1 uF, 50V, + 10% Mylar | rae | eres se | och 2 8, tomar | 409 | 202X8000-550 | Ceramic | |||
| R310 | 203X6501-285, | 470k Ohm, + 5%, 1/8W Carbon | C356 | 203X0015-105 | 4.7 uF, 25V Electrolytic | Raoo | 303x6800800 | 47k Ohm & 5% UBW Carbon | C410 | 202X8000-550 | 68 pF, 50V, + 10% Ceramic | |||
| R311 | 203X6501-065 | 56k Ohm, + 5%, 1/8W Carbon | C357 | 203X1201.013 | 0.015uF, 200V + 10% PP | rat0 | 303X6500-800 | 47k Ona | -eecarey Caibsa | |||||
| R312 | 203X6501-126 | 100k Ohm, * 5%, | 1/8W Carbon | C358 | 203X1201-034 | 0.018 uF, 200V, + 10% PP | Rai | 203X6500-800 | 47k Ohm | = 8% 1BW Carbon | ||||
| R313 | 203X6001-326 | 10k Ohm, + 5%, 1/8W Carbon | C359 | 203X0040-013 | 4.7 uF, 160V Electrolytic | Ratz | 203X9104-809 | 12k On im + pay ow Metal Ox " | ||||||
| R314 | 203X6501-044 | 47k Ohm, + 5%, 1/8W Carbon | C360 | 202X7000-482 | 0.01 uF, 50V, + 10% Ceramic | nag | coaxsinasos | Joh Ohara 200-2 | OW Metal Oxide | SEMICONDUCTORS | ||||
| R315, | 203X6500-628 | 820 Ohm, + 5%, 1/8W Carbon | 361 | 203X1100-509 | 0.015 uF, 50V, + 10% Mylar | Hae | atioree | bil | Eade | iia en | ||||
| R316 | 203X6500-420 | 120 Ohm, * 5%, 1/8W Carbon | C362 | 203X0025-058 | 10 uF, 50V Electrolytic | Baie | every | TR | Oe elcome | Teate | ; | |||
| R317 | 203X6206-441 | 2.2 Ohm, + 5%, 1/2W Carbon | C363 | 203X1205-487 | 0.01 uF, 630V, + 10% PP | Rate | 203X8601.313 | om onm By 4088 1aW' cone | 200X3206-800 | Transistor, 25C2068, 2SC1514 | ||||
| R319 | 203X6500-169 | 100 Ohm, * 5%, 1/8W Carbon | C364 | 202X7000-482 | 0.01 uF, 50V, * 10% Ceramic | i | shh | Tearoom | (R output) | |||||
| 203X6500.927 | 15k Ohm # 5%. 1/8W Garbon | Ra17 | 203X5601-313 | 2.7k | Ohm £ 10% | 1/2W Comp. | TRA02 | 200X3206-800 | Transistor, 2502068, 25C1514 | |||||
| fast | . | R418 | 203X5602-254 | 470k Ohm * 10% | 1/2W Comp. | |||||||||
| F321 | 203X6700-509 | 560 Ohm, * 5%, 1/2W Carbon | Aaig | poaeene ne | 330k Ohm | 10% 1/2W Comp. | (G output) | |||||||
| R322 | 203X9100-121 | 22 Ohm, + 5%, | 2W M.O. | SEMICONDUCTORS | raze | 203X0105-117 | 10 Ohm & 10% 2W Metal Oxide | 7403 | 200X3206-800 | Transistor, 25C2068, 251514 | ||||
| 323 | Paice | poe gah | ve (ew carbon | R423 | 203X5102-155 | 270k Ohm + 5% tAW Carbon | (B output) | |||||||
| R324 | 203X6500-988 | 27k Ohm, * 5%, 1/8W Carbon | R301 | 200x4082-614 | Transistor, 25A826Q | vasa | joanna | 500 Ohm Varieior'A Drive | x404 | 201X2100-126 | Diode, 182367 (protector) | |||
| 325 | 203X6500-326 | 47 Ohm, * 5%, 1/8W Carbon | TR302 | 200X3174-006 | Transistor, 2C17400 | yaaoe | aaxetiso14 | 500 Ohm Varistor B Drive | X405 | 201X2100-126 | Diode, 182367 (protector) | |||
| R328 | 203X6500-628 | , = 5%, 1/8W Carbon | R303 | 200X3174-006 | Transistor, 25A17400 | Vaaos | 50aea e006 | Se Onn Verscee Cuet | x406 | 201X2100-126 | Diode, 182367 (protector) | |||
| R330 | 203X6500-886 | 10k Ohm, * 5%, 1/8W Carbon | TR304 | 200X3174-006 | Transistor, 28C 17400 | bind | Pesirebceaes | Retention. | ||||||
| R331 | 203X6501-209 | 220k Ohm, + 5%, 1/8W Carbon | TR305 | 200X4049-081 | Transistor, 2SA490YLBGLI | Mpted | 204X2115008 | 5k Oh Varister B Cutott | ||||||
| R351 | 203X6500-724 | 2.2k Ohm, + 5%, 1/8W Carbon | TR306 | 200X3162-538 | Transistor, 2SC1625YLBGLI | VRA08 | 204X2000-028 | 1M Ohm Varistor Screen | ||||||
| R352 | 203X6500-927 | 15k Ohm, + 5%, 1/8W Carbon | TR307 | 200X3174.014 | Transistor, 2SC1740R | mVaristor' Screen | MISCELLANEOUS | |||||||
| R353, | 203X6500-944 | 18k Ohm, * 5%, 1/8W Carbon | TR308 | 200X3174-006 | Transistor, 28C17400 | |||||||||
| R354 | 203X6500-783 | 3.9k Ohm, + 5%, 1/8W Carbon | R351 | 200X4085-415 | Transistor, 2SA854Q | CAPACITORS | 401 | 208X5003-729 | Socket, 5 Pin | |||||
| R355, | 203x6500-902 | 12k Ohm, = 5%, 1/8W Carbon | TR352 | 200x3172-208 | Transistor, 2SC1722BKS | jy402 | 206X5003.983 | Socket. 3 Pin | ||||||
| F356 | 203X6500-561 | 470 Ohm, * 5%, | 1/8W Carbon | TR353 | 200X3174-006 | Transistor, 28C1740Q | 401 | 202X7000-247 | 1000 pF, 50V, 10% Ceramic | Pat | 204X9600-329 | Plug, 5 Pin | ||
| R357 | 203X6500-724 | 22k Ohm, + 5%, 1/8W Carbon | TR354 | 200x4082-614 | Transistor, 25A826Q | C402 | 202X7000-247 | 1000 pF, 50V, 10% Ceramic | p4o2 | 204X9600-254 | Plug, 3 Pin | |||
| R358 | 203X6500-666 | 1.2k Ohm, + 5%, 1/8W Carbon | x301 | 201X2010-144 | Diode, (SI) 182473-T72 | 7 | ||||||||
| R359 | 203X6501-088 | 68k Ohm, * 5%, 1/8W Carbon | x302 | 201X2010-144 | Diode, (SI) 152473-172 | |||||||||
| F360 | 203X5500-471 | 27 Ohm, ‘* 5%, | 1/4W Comp. | x303 | 200X8000-026 | Diode, (GE), INGOTVGL | ||||||||
| R361 | 203X6000-998 | 1.2k Ohm, * 5%, | 1/8W Carbon | x304 | 200X8010-165 | Diode (SI) 1ISS81 | ||||||||
| R363 | 203X6500-666 | 1.2k Ohm, + 5%, 1/8W Carbon | X305 | 201X2010-165, | Diode (SI) SS81 | |||||||||
| R364 | 203X9014-988 | 47k Ohm, * 5%, 1W MO. | X306 | 201X2010-165, | Diode (SI) ISS81 | |||||||||
| R365 | 203X6700-989 | 58k Ohm, + 5%, 1/2W Carbon | x307 | 200x8010-102 | Diode (S!) MA26W | 4% 297X2000-072 HIGH VOLTAGE ASSEMBLY (1701) | FINAL ASSEMBLY PARTS | |||||||
| R366 | 203X6001-148 | 3.3k Ohm, +5%, 1/8W Carbon | X308 | 200X8010-094 | Diode (SI) 1S2473 | |||||||||
| R367 | 340X2222-734 | , 12W Carbon | x351 | 201X2010-144 | Diode (SI) 182473-T72 | A*® A701 | 204Xx1625-058 | 3.3 Ohm, + 10% 10W WW Resistor | 4% 88X.0129-506 | 19VJTP22 Pix Tube | ||||
| R368 | 203X6500-785 | 1/8W Carbon | x352 | 201X2010-144 | Diode (SI) 182473-T72 | vR702 | 204x3901-125 | Focus Control | 38A5554-000 | Assy. Purity Shid/Degaussing | ||||
| R369 | 203X6500-762 | 3.3k Ohm, + 5%, | 1/4W Carbon | X353 | 201X2010-144 | Diode (SI) 1S2473-T72 | X701 | Diode (SI HV) | 205X9800-256 | Lateral/Purity Assembly | ||||
| 370 | 302X6100-961 | 1k Ohm, * 5%, 1/4W Carbon | X354 | 201X2010-144 | Diode (Si) 182473-172 | x702 | Diode (SI HV) > Part of T701 | Ak 202X1110-810 | Yoke, Deflection | |||||
| R371 | 203X6104-751 | 2.7k Ohm, * 5%, 1/4W Carbon | X355, | 200X8220-851 | Diode (Zener) RD10EB! | x703 | Diode (SI HV) | 208X2000-946 | CRT Socket | |||||
| VR301 | 204X2122-093 | Varistor, 250K Ohm, Vert. Hold | X366 | 200X8100-130 | Diode (HS) RU-1 0.3 US | 2972000072 | HY Unit (7701) | |||||||
| R302 | 204x2114.085 | Varistor, 20K Ohm, Vert. Size | 6A0397 | Plug, Line Cord | ||||||||||
| R351 | 204X2114-05! | faristor, 50K | Ohm, Hor. Hot | 9A2753-003 | ah |
MISCELLANEOUS Degaussing Coli (L701)
| CAPACITORS | 301 | 204x9300-958 | Socket, 6 Pin | |||||||||
| . | F, | 50V, + 10% Mylar | J302 | 204X9300-958 | Socket, 6 Pin | |||||||
| soz | 203x1100873 | b.a22 uF SOV. 2 10% | Mylar | Poot | 2049601 185 | Flug, 8 Pn | INTERFACE BOARD (P305) | |||||
| + | 10% | lug, 6 | Pin | |||||||||
| a) | pa | se | pea iene | TH301 | 201x0000-534 | Thermistor | (MODEL 19K 4606) | |||||
| 307 | 203X1100-928 | 0.15 uF, SOV, | 10% Mylar | |||||||||
| C309 | 203X1100-858 | 0.1 uF, 50V, + 10% | Mylar | |||||||||
| 310 | 203X0010-011 | 22 uF, 16V Electrolytic | TRANSFORMERS & COILS | RESISTORS | SEMICONDUCTORS | |||||||
| cai | 203x0020-099 | 1000 uF, 35V Electrolytic | ||||||||||
| 312 | 202X7000-469 | 0.0082 uF, 50V, + 10% Ceramic | 351 | 201X5200-091 | Coll, Horlz. Osc. | R201 | 340X3910.934 | 91 Onm, 5%, | 1/2W Carbon | TR201 | 86X0121-001 | Transistor (NPN) |
| R203 | 340X3102-934 | 1k Ohm, 5%, 1/2W Carbon | TR202 | 86X0121.001 | Transistor (NPN) | |||||||
| R204 | 340X2101-934 | 100 Ohm, 5%, 1/4W Carbon | Ec | Petey | Transistor (NPN) | |||||||
| R206 | 340X3331-944 | 330 Ohm, 10%, | 1/2W Carbon | (0066-001 | Transistor (PNP) | |||||||
| POWER BOARD (MV) | R207 | 340X3102-934 | 1k Ohm, 5%, | 12W Carbon | TR205 | 86X0066-001 | Transistor (PNP) | |||||
| R208 | 340X2152-934 | 1.5k Ohm, 5%, 1/4W Carbon | TR206 | 86X0066-001 | Transistor (PNP) | |||||||
| 503 | 203X0010-011 | 22 uF, 16V Electrolytic | R209 | 340X2101.934 | 100 Ohm, 5%, 1/4W Carbon | TR207 | 86X0121-001 | Transistor (NNP) | ||||
| RESISTORS | 551 | 203X0005-046 | 220 uF, 10V Electrolytic | R210 | 340X3102.934 | 1k Ohm, 5%, 1/2W Carbon | TR208 | 86X0121-001 | Transistor (NPN) | |||
| R211 | 340X2331-934 | 330 Ohm, 5%, | 1/4W Carbon | TR209 | 86X0121.001 | Transistor (NPN) | ||||||
| R501 | 204X1725-052 | 180 Ohm, + 10%, 15W WW | Rai2 | 340X2331.934 | 330 Ohm, 5%, 1/4W Carbon | 20201 | 66X0040-018 | Diode, Zener, 6.8v, 5%, 0.5W | ||||
| R502 | 203X6000-608 | 100 Ohm, + 5%, 1/8W Carbon | SEMICONDUCTORS | R213 | 340X2331-934 | 330 Ohm, 5%, | 1/4W Carbon | zD202 | 66X0040-019 | Diode, Zener, 3.9v, 5%, 0.5W | ||
| R503 | 203x6000-960 | 1k Ohm, + 5%, 1/8W Carbon | R214 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | |||||||
| R508 | 203X6000-879 | 560 Ohm, * 5%, 1/8W Carbon | R501 | 200X3174-006 | Transistor, 2561740 | R215, | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | ||||
| R505 | 203X9014-965 | 39k Ohm, + 5%, 1W M.O. | Ax TA5O2 | 200X3145-404 | Transistor, 2801454 | R216 | 340X2201-934 | 200 Ohm, 5%, 1/4W Carbon | MISCELLANEOUS | |||
| R506 | 203x6500-842 | 6.8k Ohm, = 5%, | 1/8W Carbon | TR5S1 | 200X3172.305 | Transistor, 2561723 | R201 | 40X0590-017 | 1.5k Ohm, Black Level Control | |||
| R551 | 203X6500-420 | 120 Ohm, + 5%, 1/8W Carbon | x501 | 201X2230-042 | Diode, (SI) Zener EQB01-06V | $201 | 204X9300-958 | Socket, 6 Pin | ||||
| R501 | 204X2050-001 | Varistor Vert. Adj | x502 | 201X2010-144 | Diode, (Si) 1S2473-172 | J202 | 204X9300-958 | Socket, 6 Pin | ||||
| CAPACITORS | J203 | 206X5019-207 | Socket, 4 Pin | |||||||||
| P201 | 204X9601-195 | Plug, 6 Pin | ||||||||||
| CAPACITORS | MISCELLANEOUS | C201 | 45X0524-038 | 1000 uF, 16V Electrolytic | P202 | 204X9601-195 | Plug, 6 Pin | |||||
| 203 | 204X9600-845, | Plug, 4 Pin | ||||||||||
| 501 | 203X0040-020 | 10 uF, 160V Electrolytic | J501 | 204X9300-958 | Socket, 6 Pin | P205 | 6A0383-006 | Plug, 6 Pin | ||||
| C502 | 202X7000-281 | 1500 pF, SOV, + 10% Ceramic | P501 | 204X9601-195 | Plug, 6 Pin | |||||||
| THSO1 | 201X0000618 | Thermistor |
6-11 6-12
Ix301,x302,x908,x308 \SYNC AMP. [25CaS4C or gacises
X303 BEAM LIMITER 2SA673 X304 BLANKING 28C484C or 2icices
X901 POWER DRIVE 257686 X 902 ERROR AMP 2SC1890 J
B x04 28cli06a, 25c145. POWER REGULATOR
x bur my Xrore: GT RE VIDEO OUTPUT Bete Bes OT |
{exer
ol w our ° ° f 28CISOr WI, ascea7iv 280898 or te ay-s03n4 Ve seit ne sre 501 ORV 28Ca6il or eC26108K 250869 or 250820 X70! X-RAY PROTECTOR 25C4S4C or 2501685
AciZ0V 60H:/50H2 10%
6-13 Hele]
00-4147-04 GO07-CBO Schematic Notes Unless otherwise specified Resistance: (Q) (K-~K2, MMQ), 1/4 (W) carbon resistor Capacitance: 1 or higher— (pF), less than 1-> (yF) working voltage-» 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP -= non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection oh indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) A&A replace all components marked with safety syrnbol with identical type.
Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
REPLACEMENT PARTS LIST - ELECTROHOME 19” MONITOR
special characteristics important to safety. Components identified by the A symbol in the PARTS LIST and on the Schematic have
DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | C Cap. |
| Comp. R | : Composition Resistor | M Cap |
| OMR | : Oxide Metal Film Resistor | E Cap. |
| VR | : Variable Resistor | BP E Cap. |
MF R : Metal Film Resistor
| CMF R | : Coating Metal Film Resistor | MM Cap. |
| UNF R | : Nonflammable Resistor | PP Cap. |
| FR | : Fusible Resistor | MPP Cap. |
PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor
SERVICE REPLACEMENT PARTS LIST
Symbol Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y Purity Shield Ass'y Part Number SU-1133A SU-3032A 07-220083-03 Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19” A AdDeflection Yoke PC Magnet A Flyback Transf. A ASHVR ROS UNF Resistor 2200,25W K C04 C Capacitor 150pF, AC1.5KV x01 Si. Transistor x02 Si. Transistor sc Screw #8-% sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH. Support Brkt. LH Chassis Base Yoke Wedge (3)
Purity Shield Ass’y. Parts List
Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pcs.) Catt Capacitor 100nF 10% 400V R921 Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug
CRT Socket P.C.B. Ass’y (SU-3032A) Parts List
Resistors Symbol Description
| 3105, | v | R 200 |
| R3106 | Vv | R 200 |
| R3113 | Vv | R SK |
| R3114 | Vv | R SK |
| R3115 | Vv | R 5K |
| R3116 | OM | R 10KQ2W J |
| R3117 | OM | R 10KQ2W J |
| R3118 | OM | R 10KQ2W J |
R3119 Comp. R 3.3K2%W K R3120 Comp. R 3.3KQ%W K C3121 Comp. R 3.3KQ2%W K
Capacitors Symbol Description C3107 E Cap. 10uF 250V A 3108 C Cap. 1000pF DC1400v P
Coils Symbol Description L3101 Peaking Coil
6-15 Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01
Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09
Part-Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEWS53EA-106 QCZ9001-102M
Part Number QQL043K-101
Semiconductors Symbol X3101 X3102 X3103
Misceilaneous Symbol & Description Si, Transistor SI. Transistor Si. Transistor
Description ASCRT Socket
Main PCB Ass'y (SU-1133A) Parts List
Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AR1703 A\R1704 AR1901 R1902 R1903 R1904 R1905 4Q1908 4A1909 R1910 AXFR1901
Capacitors Symbol C1301 1402 C1407 1411 1412 1508 Ac1512 ACi1513 Ac1514 C1815 C1520 C1523 C1524 AC1531 AC1532 C1904 C1905 Description
| v | R | 2002 |
| v | R | 2002 |
CMF R 6801WJ OM R 3.3KQ1W J OM R 27KQiW J
| OM | R | 12KQ2W J |
| v | R | 10KQ |
AF R 6822W K
| ACMF | RR | 11.8KQ%W +1% |
| Vv | R | 5KQ |
| OM | R | 10KQ2W J |
OM R 8.2KQ2W J OM R 82022W J CMF R 8201WJ CMF R 4.7021WJ OM R 68n2w J OM R 30021W J ZN R ZN R
| ACMF | RR | 392.%W +1% |
ACMF Re 7.68KQ.%W +1% AsPosistor UNF R 2Q7WK CMF R 4.723W J
| OM | R | 10KQ2W J |
| OM | R | 18KQiWd |
ACMF R 472.%4W +1% Vv R 2kQ ACMF R 2.74KQ%W +1%
| AF | R | 2202%W K |
Description BPE Cap. 3.3uF 50V A Tan. Cap. 2.2uF 16V K E E E PP App APP APP PP BPE E M APP APP Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. 4.7UF 6.3V A 100uF 160V A 3.3uF 160V A 5600uF 50V J 2000pF DC1500V J 2000pF DC1500V J 2000pF DC1500V J 0.53uF DC1200V J 3.3uF 50V A 1uF 160V A 0.1uF 200V K 2000pF DC1500V J 1500pF DC1500V J
10uF 250V A
6-16 Part Number 28C1514VC 28C1514VC 2801514VC
Part Number A76068
Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRG019J-332 QRG019J-272 QRGO26J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRG026J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 AT5414 QRFO76K-2RO QRX039J-4R7 QRG026J-103Z QRGO19J-183 QRV122F-470Z QVPS5A0B-023E QRV142F-2741 QRH124K-221M
Part Number QEN61HA-335Z QEE51CK-225B QEWS1JA-475 QEWS2CA-107 QEW52CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEW52EA-106
Colle
Symbol Description Part Number
| £1502 | Linarity Coil | A39835 |
| £1503 | Width Coll | C30380-A |
| 11504 | Heater Choke | C80445-A |
Transtormera
| T1501 | Hor, Drive Transt. | A46022-BM |
| T1503 | Side Pin Transt. | C38050-A |
Semiconductors
| (C1501 | Ic | HA11244 |
| X1107 | Si. Transistor | 2SC1685(R) |
| x1102 | Si. Transistor | 2SA673(C) |
| X1103 | Si. Transistor | 28C1685(R) |
| X1104 | Si. Transistor | 2SA673(C) |
| X1105 | Si. Transistor | 2SC1685(R) |
| X1106 | Si. Transistor | 2SA673(C) |
| X1301 | Si. Transistor | 2SC1685(R) |
| X1302 | Si. Transistor | 2SC1685(R) |
| X1303 | Si. Transistor | 2SA673(C) |
| X1304 | Si. Transistor | 2SC1685(R) |
| X1305 | Si. Transistor | 2SC1685(R) |
| X1401 | Si. Transistor | 28D478 |
| X1402 | Si. Transistor | 28D478 |
| 1501 | Si. Transistor | 2SC2610BK |
| X1901 | Si. Transistor | 2SC2688 (K.L.M.) |
| X1902 | Si. Transistor | 2SC1890A (E.F.) |
| D1101 | Si. Diode | WO6A, |
| D1102 | Si. Diode | WO6A |
| DB1103 | Si. Diode | WO6A |
| D1301 | Si. Diode | 1SZ473H |
| D1401 | Si. Diode | 18Z473H |
| D1402 | Zener Diode | RD10F(C) |
| D1503 | Si. Diode | HF-4 |
| D1504 | Si. Diode | VO9E |
D1505 Zener Diode RD11E(B)
| 01506 | Si. Diode | WO6A |
| D1507 | Si. Diode | 1SS81 |
| D1508 | Si. Diode | 18Z473H |
| Ap1701 | A\Zener Diode | RD20EV2 |
| 4\D1901 | ASi. Diode | 1S1887A |
| 4AXD1902 | ASSi. Diode | 181887A |
| 401903 | ASi. Diode | 181887A |
| A\D1904 | ASi. Diode | 1S1887A |
| 4xD1905 | AdZener Diode | RO6.8EV3 |
Miscellaneous
| ASF1901 | AsFuse 1.254 | QMF53U1-1R25S, |
| AF1902 | AXUL Fuse 3A | QMF66U1-3ROS |
6-17
neo swe XI01.x103 and XI0S VIDEO AMP. 2SC454C o, 281685 Xi02,x104 and XI06 VIDEO_ AMP. 25A673C SSS SOTO ? 28C26I! or 2SCISIGV
——<—
- 28casac
IOI POWER REGULATOR * : STR3B3 SU-I103A ‘ae MAIN PCB ASSY r |
X40), 402 esas
Schematic Notes Unless otherwise specified Resistance: (Q) (K*KQ., M-MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1 (yF) working voltage -> 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value (y F)/working voltage (V), X50! HORN 1H NP — non-polar (or bipolar) electrolytic cap. ‘BECASSE’ ‘or ASC WES. 28C26ii or Z8C26I0BK 250869 Refer to the parts list for additional component information. Q indicates test point connection oh indicates chassis ground unless otherwise specified Hz _ indicates cycles per second oo} hy ACI20V 60H2/S0H2 210%
For safety purposes (and continuing reliability) AN replace all components marked with safety symbol with identical type.
G07-FBO Parts identification on circuit boards: 00-4147-03 e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)
6-18
REPLACEMENT PARTS LIST - ELECTROHOME 13’’ MONITOR
Components identitied by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.
Abbreviations for Resistors and Capacitors
Resistor Capacitor
| CR | : Carbon Resistor | C Cap. | Ceramic Capacitor |
| Comp. R | : Composition Resistor | M Cap | Mylar Capacitor |
| OMR | : Oxide Metal Film Resistor | E Cap. | Electrolytic Capacitor |
| VR | : Variable Resistor | BP E Cap. | Bi-Polar (or Non-Polar) |
| MF R | : Metal Film Resistor | Electrolytic Capacitor | |
| CMF R | Coating Metal Film Resistor | MM Cap. | Metalized Mylar Capacitor |
| UNF R | Nonflammable Resistor | PP Cap. | Polypropylene Capacitor |
| FR | Fusible Resistor | MPP Cap. | Metalized PP Capacitor |
PS Cap Polystyrol Capacitor Tan. Cap. Tantal Capacitor
Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.
Symbol
Outside of the P.C.B. Ass'y Symbol Avot ASDY01
Art AROS Axcoa x01 1001 Lot
BR BR sc WA
CH Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y
Description Apicture Tube A\Deflection Yoke PC Magnet Wedge AFlyback Transf. AFocus V R UNF Resistor 22092, 25W. K AC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Degausing Coil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Ass’y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) Clip P.C.B. Support (2) Ground Lug Chassis Base
6-19 Part Number SU-1103A SU-3016A
Part Number 370ESB22(E) 29123-V A76366-A 30008 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass'y (SU-1103A) Parts List
Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 A\FR1401 AXR1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 4sR1703 ASR1704 ASR1901 R1902 R1903 R1904 ASFR1901
Capacitors Symbol 1402 c14i1 C1412 C1508 C1511 AC1512 AXC1513 AC1514 C1515 1520 C1524 1904 C1905 A\C1907
Coils Symbol L1501 L1502 L1503 L1504 L1901
Transformers Symbol T1501 T1503 Desecripti vooR v R CMF R OM OM
ZN OR ACMF R ACMF R AsPosistor UNF R CMF R OM R AF R
Descripti Tan. Cap. E Cap. E Cap. PP Cap. E Cap. ASPP_ Cap. ion 2002, 2002, 682Q1W J 3.3KQ1W J 2.7KQ1IW J 12KQ2W J 10KQ 682.2W K T1.BKQYW +1% 5K2 10KQ2W J 5.6KQ2W J 6802.2W J 8.201W J 4791W J 5622W J 39021W J
39K QW +1% 7.68KQUW +1%
20Q7W K 5.623W J 1OKQ2W J 2202 %W K
lon
2.2uF 16V K 100uF 160V A 3.3uF 160V A 5600pF 50V J 47uF 160V A 2000pF DC1500V J AxpP Cap. 2000pF DC1500V J APP Cap. PP Cap. BPE Cap. M_ Cap. 2500pF DC1500V J 0.53uF DC1200V K 1uF 50V A 0.1uF 200V K E Cap. E Cap. XMM Cap. 10uF 250V A . O.1UF ACI50V Z
Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter
Description Hor. Drive Transf. Side Pin Transf.
6-20 Part Number QVZ3230-022 QVZ3230-022 QRX019U-6R8 QRG019J-332 QRG019J-272 QRG029J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO29J-103 QRG029J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORG029J-560 ORGO019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 AT5414 QRFO76K-2R0 QRX039J-5R6 QRG026J-103Z QRH124K-221M
Part Number QEES1CK-225B QEWS52CA-107 QEW52CA-335 QFP31HJ-562 QEWS52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEW52EA-106 QFZ9008-104
Part Number A75360-6 A39934 30380-A C30333-A A39475-J
Part Number A46022-BM 39050-A
Semiconductors Symbol 101501
x1101 x1102 X1103 X1104 X1105 X1106 X1301 x1302 X1303 X1304 X1305 x1401 x1402 X1501 x1701 1101 01102 D1103 D1301 D1401 D1402 D1503 D1504 D1505 01506 01507 D1508 A\D1701 A\D1901 401902 A\D1903 4A\D1904
Miscellaneous Symbol ASF1901 AXF1902 Description Lc.
Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AdZener Diode ASSi. Diode ASi. Diode ASSi. Diode ASI. Diode
Description A\Fuse 1A AXUL Fuse 3A
6-21 Part Number HA11244
2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SD478 2SD478 2SC2610BK 2SC1685(P-S) WO6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 VOSE RD11E(B) ‘WO6A 18881 182473H RD20EV2 1S1887A 1S1887A 181887A 181887A
Part Number QMF53U1-1ROS QMF66U1-3R0S
CRT Socket P.C.B. Ass'y (SU-3016A) Parts List
Resistors Symbol R3105 R3106 R3113 R3114 R315 R3116 R3117 R3118 R3119 R3120 R3121
Capacitors Symbol C3107 C3108
Coils Symbol 3101
Semiconductors Symbol X3101 X3102 X3103
Miscellaneous Symbol a& Description 2002 2002 5K 5K 5KQ WK NAW J IOKQ2W J OM R 10K22W J Comp. R 3.3KQ2%WK Comp. R 3.3KQ2%W K Comp. A 3.3KQYWK eoo<<<<< DDDDDVUVD iM IM
Description E Cap. 10uF 250V A C Cap. 1000pF DC1400v P
Description Peaking coil
Description Si, Transistor Si. Transistor Si. Transistor
Description A\CRT Socket
6-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO029J-103 QRGO29J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332
Part Number QEWS2EA-106 QCZ9001-102M
Part Number QQL043K-101
Part Number 2SC2611 2802611 28C2611
Part Number AT5522
Vil Schematics and Wiring Diagrams
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
7-2 MONITOR ACKS pay BOSCONIAN MINI +a] BU
aBLU-GRY cry a8 Bu
FILTER LINE. \ ‘
RAPID FIRE BD.
JL use P.C#1084-91410-A000 [Lo save
g H i BAN 8 OFF 3a.
BAN EM
MT-82
tg
- ry Reopewonesy sc geveTUTITOTI TN, sib BLK
a
r ) 2 |i a)
Lk
a ! LJ
MONITOR POWER JACK awe Loseoonegonacgoeearncecrrcoormerrre:ceeePerreonnes MT-87 XFORMER:
tv
REO.
LK RED x woG aN LOGIC GND, REO RED Lo bo
ae POWER SUPPLY BD.
Losi
Locie GND,
+ ae
VIDEO 8D Pc# 0084-91405 08.8 | gg MOVE BIGHT SeLect o EL. SELECT ou CPU BD. P.c# M84 91404-2508
NOTES He sane ray s-Bue, ame a BLU-GRY
aBLU-cRY a8
\
°
BOSCONIAN CI. REVISIONS SCHEMATIC® MOSI-00557- A003 m ony BAN 8 ON-OFF SH
BAN S
au|-o« BAN +
Bue
ow Coorenovoereroonorreccerserersorser: ccorPere arene? Blue
va MONITOR POWER JACK
vA 10 Re
MONITOR SACKS pe.
BK VIDEO BD. Pc® A084 -91405- 85.28 REO x Se L0GIC_6No, STON BPOVTOT TS, [=
TOO OOTT ov.
com
ov oe
RED
vex
MT-91 XFORMER
et 1084-90414 C995
LoGic GND, LOGIC GND,
‘seLecr CPU BD. P.c® Abd -91404 - 2508,
7-3
DESIGNATION
c2 cs ca cs ce cr
Rt R2 RS Re RS Re
Qt ez
ut v2
ut HSI FL Fe FS
FCIA,FCIB,EC2A FC2B,FCSA,FCSB
a a2
Hat
MHo2
wHut
Twi-TW3
7-4 DESCRIPTION
10000 MF 35V AX. ELEC. LOIMF SOV AX.CER, IMF 25V ‘TANT. 20000 MF I6V AX. ELEC. 1OOPF GOV AX.CER 4TOMF IGV AX. ELEC. 4TOOMF26v " *
470 OHM I/4W 5% CREN co" 2K . “ seo" sew so os Oo io oO
100 OHM = I74W CREN. FLM.
AlGF IN4004 R750 AISF Alae
TIPS 2N3055
La3i7 3832
FERROXCUBE BEAD HEAT SINK FUSE 2A
"6A
FUSECLIP W/ STOP
CONN. KK.I56 (RA)(5~PIN) (6-PIN) . (RAYS PIN) (13-PIN)
MOUNTING HARDWARE a1
- SCREW 4-40XI0_ SLTRND
- WSH.4 120 - 250-018 () HEXNUT 4-40
- SHOULDER WSH. 974-302 THERMAL COMPOUD AS REQ.
- TO- 220 INSULATOR RT-3.6MICA MOUNTING HARDWARE Q2
- SCREW 4-40X10 SLT RND
- WSH4 120-250-018
- HEXNUT 4-40
- SHOULDER WSH. 974-302 THERMAL COMPOUD AS REQ. () TO-3 RT- 1.8 FILM
MOUNTING HARDWARE UI
- SCREW 4- 40X10 SLT RND
- WSH 4 120-250-018 (HEXNUT 4-40
- SHOULDER WSH. 974-302 THERMAL COMPOUD AS REQ
- TO- 220 INSULATOR RT- 3.6 MICA
TIE WRAPS J2
Jl FL
Foi Foie _ rm |
Ft bs fz] im ct + @®
TMS (erm)
rom | Fe ECZA cee rm | = 4
RS we Ra] cs) ca + Te) ve
Fs Fo3A Fo3B me
ce + rom | ow oe cr + rca | L com | pio HEAT SINK
ed = ~
O] Mia!
HSI
DECIMAL
00 MOT SCALE owG, DESCRIPTION
100 PF 50v AX.CER O1MF " " 1MF 25v TANT. 470MF " AX.ELEC.
| 4700MF * | =) | = |
10000MF 35v AX.ELEC 20000 16v MF" *
10 OHM 1/4w 5% CBN joo" Of 470" 5
| B10" | * | # | # |
| 560" | * | « | # |
| 27Ke | 8 | oe | |
| 100" | = * | CBN FLM |
1N4004 AI4F AISF MR750
TIP31 2N3055
3532 M317
FERROXCUBE BEAD
HEAT SINK
FUSE 2A FUSE 6A FUSE 8A
FUSECLIP
KK 156 (RA) (5) KK 156 (RA) (6) KK 156 (RA) (13)
SCREW 4-40x10 WSH 4 120-.250-018 HEXNUT 4-40 SHOULDER WSH THERMAL COMPOUND TO-220, INSULATOR TO-3 INSULATOR TIE WRAPS pce =
we oe wees
°
Hoam pena aan
Te)
185 DAG 1S CONFIDENTIAL PERTY OF MIOWAY MFG CO MIDWAY MFG. CO. FRANKLIN PK. I. 60 ‘ASSEMBLY DRWNG PWR. SUPP. A084 -90414..c936 DESIGNATION
cs c2 c3 ce c7 C1 ca
Re R2 RI RS R4 R3
vRi
D3 D1,D2,010 06-09 04,05
a1 a2
u2. ut
u4
Hs1
FA F3 F2
FC1A,FC1B,FC2A, FC2B,FC3A,FC3B
J1,d2 Jt J2
MHU1,MHQ1,MHQ2
MHU1,MHQ1 MHQ2 TW1-TW3
MOSI-00985-coz8 PART NUMBER 0808 - 00800- 2100 017 1-097H2-JXXX 0935-00814-0100 0175-27 1EX-EXXX 0808 -00800- 2200 0175-322GX-EXBX 0935-008 14-0800
0062-05 183-1Xxx 0062-110B3-1xXxXx 0062+ 156B3-1Xxx 0062-159B3-1XXX 0062-162B83-1XXxx 0062-19983-1xxx
0063-025AX-1DEX
0508-00801-0200 0064- 168XX-XXGX 0064- 169XX-XXGX 0064-303XX-XXJX
0065-485XX-XXXX 0935-00800-0000
0066-044BX-XXXX 0935-00804-3600
0017-00009-0225
0068-045XXx-ABDX
0017-00003-0005 0017-00003-0008 0017-00003-0184
0017-00003-0214
3000- 16387-0500 3000- 16387-0600 3000- 16387-1300
0017-00101-0727 0017-00104-0071 0017-00103-0002 0017-00042-0109 0017-00009-0204 0017-00003-0205 0017-00042-0108 0017-00042-0105 A080 -90414 ~C935
REVISIONS
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DESIGNATION
7-6 DESIGNATION LIST
DESCRIPTION
cl.c2 .IMF 100V MYLAR c3-C7 .OIMF 25V AX CER
RI-R4 (MEG OHM |/4w 5% CRBN RES " a
R IK uw o a “ “ R Ko ee
ul LMS56 v2 7400
Ji,u2 KK.I56 VERT 2(6-PIN) 2(2-PIN) MHI-MH4 SNAP BUSHING I/4" CROSS REFERENCE LIST
DESCRIPTION QUANTITY DESIGNATION PART #
| .OIMF 25VAXCER | 5 | C3-C7 | 0508- 00800-0800 | |||
| .IMF lOOV 10% MYLAR | 2 | cl, c2 | 0508-00800- 2300 | |||
| 68 OHMI/4w 5% CRBN RES. 2 | R6E,RS | 0062-098B3- IX XX | ||||
| in | "SM | HH | 3g | R5,R7 | 0062-179B3- IXXX | |
| IMeg" " | " | " | " | 4 | RI-R4 | 0062-323B3- IXXX |
| LMSS6 | I | ul | 0508 - 00803-5500 | |||
| 7400 | I | v2 | 0808 -00803-5600 | |||
| KK.IS6 CON. (2-PIN) | 2 | Jl.u2 | 3000-16335 -0200 | |||
| (6@-PIN) | 2 | JIv2 | 3000-16335-0600 |
MOUNTING HARDWARD
| SNAP BUSHING 1/4 | 4 | MHI-MH4 | 00I7- 00042-0014 |
| RAPID FIRE P.C | ! | A080- 91410 -A000 A080-91410-A000 |
PROJECT ENG: JERRY SZERSZEN ‘OLERANCES . GALAGA OTHERWISE SPEC Tricity TVR voz J 14 lo9-30 -8! Trot fr93 UG 63 ONEIDENTIAL & PROPERTY OF MIDWAY MFG CO
MIDWAY MFG. CO. FRANKLIN PK., IL. 60131 ABALLYCO.
| RAPID | FIRE | P.C |
REVISIONS DECIMAL HOLE DIA ANGLE : yi; PRS ASSEMBLY DRAWING PART NO 05-1 -0-0-1-1:4-A-0-0'1 FRACTIONAL Tareas T
DO NOT SCALE DWG A082-91410-A000
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DESIGNATION
ox
Ree—nee DESIGNATION LIST
ger aggeey SSUNERSS Hi DESCRIPTION
SSgSseS eer ee esses ses
ree. Mec4onex nT Tibatoxeatt anaes = Ghwana iea~eso-one Fur st Gey wana 100-260-018 ext st woscomian cru 80, osu CROSS REFERENCE LIST
| DESCRIPTION | gual | DesteNsTION | PART No | DESCRIPTION | Suan | DESIGNATION | —PART NO |
| leo cer, | 2 | case | ost0-00800-0908 | Paom as | j | 2800-00808-3100 | |
| Sour Ft | H | esos? | nmo-20800=1100 | H | 4 | ||
| ‘ona eee | { | ca | 22t0-c0800 0000 | ot | |||
| ear” | * | creer, | ons0-2o8e0-o7e0 | ' | os | ||
| ‘seo- ews = 0600 | ' | ie | Gove coset nee | ||||
| seso-aotoo-no0 | H | Pr | 3e0-00m08 2700 | ||||
| cane | Seno-c0e00-1700 | H | |||||
| oe | Seeo-goe0-1600 | ' | |||||
| on | ‘Sse0-sose0-ro00 | ' | |||||
| on | Sesona0e00 “608 | : |
st Geeocooteo=t800 oes 11083 -100K + a ; :
| : | te.ane, wnt cree | ’ |
A te eorren H foro exrweaoen sore
| . | conn, pebmeaoen tem | * | Sorr-oonai-oass |
: 3 ousting wanomnt
| H | sesame nut | . | mere | 297-90103-0008 |
| : | Siete raw | H | * | |
| i | foe weeoom nina | : | ||
| ' | Wd iaoroow er se | : | Sorrcaatoa-somt | |
| ’ | oscomian cru re | ' | soto-sisit-sas0 |
A : :
| ' | o | 2880-00801 -0100 |
' 680-oo4oe 080° ' c000- cover 2100 H teeo-oono# 0300
| oma cusion ic | : | cone 0080X-x4Px |
| see | : | soak ements |
| Stee | \ | Sone o1gtacxarx |
Hi |
| iter | ; | FA | Seto-cobas 300 |
| Tor | on | eto ~oo008-o000 |
4 Seeo-ooest ono Ta seo sees tee
| fuser | : | : |
| ire | H | : |
| weer | ' | : |
| Soorewoe | H | : |
PROJECT v0: AEERSION ___ [>see] WIDWAY MFG. CO.
- - Soscom ao ‘A084 ~914 12 ~ 8580 jMOS 1 -00550-B010 ASS'Y DRWN:
BREBRERR RRB REERS ie
DESIGNATION LIST.
DESIGNATION DESCRPTION DESIGNATION DESCRIPTION
| eh.ce | Sowrue | it |
| a | 01a 1oov wx rar | 7 |
| & | Ge Me soy om can | ee00 |
| Ed | Bem | 12 |
Huse. un. ockins spacers 50 Pw wr anoue
Iiosow CABLE“ 33r7 G0 CONNECTOR
etree enond suT not 80TH Serion mc) alae’ toe.d 0 NOTE: RAM KIT 8 WILL UTILZE ETHER CF THE crriont=ty Bae woe: ae orion (2) dz 106. 34,38 DESCRIPTION, CROSS REFERENCE LIST
DESIGNATION. ry
Esico.cer eeiee
ange m0 -c0802- 0400 eanan
er 080 Susman ses farm > .
on00.00904-2200
—— ‘os0.0148-0850
‘BOSCONIAN VIDEO 084-91413-B550 ASS'Y DRWNG.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
KE | BETWEEN CONTACTS 5, AND6,F 4—KEY2 EETHEEN CONTACTS 3.C AND 4.0 sls 413.21
| DESIGNATION | DESCRIPTION | Cea |
cr «IMP AXCER ca-cs 47 PFAXCER Ce, C7 4 TOPE AX CER cBCIS 1OOPF AX CER Cl4-C3@ -O1 MFAXCER ® J1M.H. CJ3_]
| Linke | (CHOKE JOWH W.W. MILLER | J5 | | |
LSE (CHOKE 1O.UH WW, LO-LI2 CHOKE ENCAP 10 UH cae eee)
(2)WSH 6 145~.250~.032
- BRK T.-CONN. FIN, S|
| vt | F.C. ED6E CONN | , | ni | |||
| v2.03 | 5 PIN HEADER | n | f | |||
| J4.dS | 6 PIN HEADER | ) | | | k | Ss | S) |
JIMA, 2EDGE CONN. KEY
| (216-3210 SLOT PAN SCREW | sy | s |
IG) IS alioys} S| IIc} si [va |
| DESCRIPTION | -QUANTIZY | QESIGNATION | PHANTOM NUMBER | GESCRIPTION: | QUANTITY | QESIGNATION | PHANTOM NUMBER |
| 47 PF SOVAXCER = | cas | 0550-00800~0500 | SPIN HEADER | 2 | evs | 0G17~00021-0443 | |
| 1OOPF SOVAXCER | «6 | 8-c13. | 0550-00800-0100 | aed | |||
| A70PF SOVAKCER = 2 | c6,c7 | 0550~00800-0200 | GAIN HEADER | 2 | ve-uS | 0017" 00aI- 0428) | |
| AOINFSOVAXCER | 23 | c14-C36 | 0550-00800-0300 | OME S208 | |||
| “IMF SGVAXCER | I | co | 0550-00800-0400 | PCEDGECON Ker | 2 | vie | C017-0002!-0396 |
| 10H WW. AF | 4 | Lila | O06? ~OBIXX-XKAX | 6-32x10 SLOT | e | ide | 0017 00101-0574 |
CHOKE MILLER PAN SCREW
| own, RE | 4 | 5-18 | 050~00604-0100 | WSHE | 2 | viet | 9017-90106 -00C2 |
CHOKE 145-, 250,032
| OUMENcAP | 4 | t9-uI2 | 0550-00804-0200 | Pear | r | oe | 0856-0016-o0xr |
| PC EDGE CONN | ' | wt | C017 -0002I-0418 | cones |
PROJECT ENGINEER L.CEKKER ‘THIS OWG. 1S CONFIDENTIAL & PROPERTY OF MIDWAY MEG.cO_ [—[_] ‘Dat. TOLERANCES tT Seer F MIDWAY MFG, CO. PLEASE DESTROY ALL PRINTS DATED FRACTIONAL. EcMAL BOSCONIAN FILTER RC. PARTNO. 4-82
| PRIOR TO |-4-82 | ous OM | ASSY. DRWNG, | IM0-5-1 -0-0-5-5- 0-A-0-1-4] |
| te | 4 | ‘4084-914/4-A550 |
TO CABLE
as
ANGLE ‘00 NOT SCALE DWG PROVECT ENG:L. DEKKER
THiS OWG 1S,
FRANKLIN PK IL 60137 BOSCONIAN MIDWAY MFG. C ONFIDENTIAL & PROPERTY OF MIDWAY MFG _CO
A084 -9i-)- FILTER BOARD 55. PART NO. os! -00550-AOI5 REVISIONS
7-13 #*1OUH WW LS COR
TO P.C. BOARD
+5V 3=
AUDIO RTN
Liver #lOUH WW L2 THA NN
c2
J2 2 ~ ; ale 1OUH W.W LS TOON
COIN METER
tou cl 1OUH W.W LB TVTH-
+5VCRMETER F,6 —> Yo ez # 1OUH W.WL4 ft c307-.01
GND GND GND GND A ! H TEST POS.
8< OCH T * 1ODH W.W OFTOY
47PF c4 ul 47 cs °
Pl SELECT l= CREDIT S.W J P2 SELECT 10 < COIN S.W.
K <2 cI?
ga Pir 636=501
PI DOWN
p. Pl RIGHT IC35—-(
P! FIRE M< GND Zz 22 GND [3—-P2 DOWN ++
15—l2 ¥P Y P2 RIGHT 4+ + 14
P2 LEFT P2 FIRE Vita l2
11+ SPKR Lo lou H WW TTI _LS
“O' ca7 + .Ol c29 1OUH W.W 1.7 OTA
ONLY “ IOUH Lo COOH 1OUH LI! COOH 1OUH 110
ALL .1+.01ARE MF ALL CAPS AX. CER. UNLESS NOTED OTHERWISE © 1.5 AMP (MILLER TYPE) INDUCTORS c8 ’ i TIER
1OOPF ci2 cis torr t | |