CATHODE RAY TOMES

VS Slalom Attachment PAK

Vs. Slalom (Rare Coin-It Inc., 1986) · Document · 16 pages · 11 sections · original scan

Page 1

ACTION E

ATTACHMENT

PAK MANUAL

a\

VS. UniSystem® (UPRIGHT) VS, DualSystem™ (UPRIGHT)

FOR INSTALLATION IN

  • ©1986 RARE, LTD. LICENSED EXCLUSIVELY TO Nintendo of America Inc. TM of Nintendo of America Inc. ©1986 Nintendo of America Inc.
Page 2

TABLE OF CONTENTS

I. Introduction... 0.0... cence eee e eee 1 ll. Contents of VS. Slalom Pak .. 0.6.0.0 -0 2020 e cece cere ee 2

Ill. List of Tools Needed .. 0.0... 3 IV. Installation Process ... 2.0.0.0... 0c cece cece eee eee 47 V. Reorder Parts Lists ........ 00.22. e eee eee need 8-12 VI. Wiring Diagram .. 2... cece cence ee 12

Page 3

|. INTRODUCTION VS. SLALOM PAK

This VS.-Pak® uses a special ski attachment which enhances game play. The ski attachment may be used with any VS. UniSystem (kit or dedicated) Upright or any VS. DuatSystem Upright game. Before you begin, be sure you are properly prepared. Thoroughly read this instruction manual to familiarize yourself with the proper procedures and make certain that you have all the necessary tools to install the ski attachment.

If you have any questions, please call Nintendo Service at 1-(800)-633-3236.

Page 4

Il. CONTENTS OF VS. SLALOM PAK

PARTS NAME QUANTITY REMARKS,

VS. Slalom Pak1in case

Ski Base 1

Control Panel1with poles attached
Control Panel Spacer1for VS. DualSystem (Upright)

Control Panel Clamp 2

8-32 x 1” Phillips Machine Screw8for VS. DualSystem (Upright)
6-32 x 3/8” Button Head Square Drive8for pole covers

Square Drive Bit 1 VS. Slalom Manual 1

No. 14 x 3/4” Hex Tapping Screw 3

Page 5

lll. LIST OF TOOLS NEEDED

Crescent Wrench

Electric Drill (optional) 3/16" Drill Bit (optional) Interchangeable Bit Screw Driver 5/64” Hex Wrench

Phillips Screwdriver

Square Drive Bit (included)

Page 6

IV. INSTALLATION PROCESS

  • Installation of Control Panel Assembly (For VS. UniSystem Kit Upright Cabinets) A. Remove existing control panel and save for future VS.-Paks. B. Install the VS. Slalom control panel assembly making sure to connect the 15 pin connector and fasten both hold down clasps. (See Illustration 1-1)

(For VS. UniSystem Dedicated Upright Cabinets) A. Remove existing control panel and save for future VS.-Paks. B. Remove the control panel bar by removing the four (4) 6-32 x 1/2” flat head allen screws. (See Illustration 1-2) C. Replace the four (4) 6-32 x 1/2” flat allen screws into the control panel.

Important: Be sure to replace the four (4) 6-32 x 1/2” flat head allen screws or it will become weak.

D. Install the VS. Slalom control panel assembly making sure to connect the 15 pin connector and fasten both hold down clasps. (See Illustration 1-2)

Page 7

REMOVE Control Panel bar

(replace screws)

(For VS. DualSystem Uprights) A. Remove the control panel from the side of the game that the VS. Slalom will be installed in. B. Remove the two (2) joysticks, eight (8) buttons and the wire harness from the dual control panel.

Note: Be sure to save these parts for future VS.-Paks.

C. Remove the control panel bar by removing the four (4) 6-32 x 1/2” flat head allen screws. (See Illustration 1-3) D. Replace the four (4) 6-32 x 1/2” flat head allen screws.

Important: Be sure to replace the four (4) 6-32 x 1/2” flat head allen screws into the control panel or it will become weak. E. Remove the two (2) fastener brackets from the VS. Slalom control panel. (See Illustration 1-3) F. Fasten the VS. DualSystem control panel to the VS. Slalom control panel using the two
  • control panel clamps, eight (8) 8-32 x 1” phillips machine screws, and the control panel spacer. (See Illustration 1-4)
Important: The wire harness 15 pin connector must be pushed through the spacer hole, control panel joystick hole and control panel clamp slot.
Page 8
Note: The control panel spacer can be used for either the right or left control panel on a VS. DualSystem. G. Install the VS. DualSystem/VS. Slalom control panel assembly making sure to connect the 15 pin connector and fasten both hold down clasps. (See Illustration 1-5) (For VS. UniSystem Pac-Man* Upright) A. Attach the VS. Slalom control panel to the UniSystem (Pac-Man) control panel by following the same steps used for VS. DualSystem.
Important: Do not use control panel spacer for Pac-Man control panels. B. Line up the joystick holes on the Pac-Man control panel to the VS. Slalom control as shown. (See Illustration 1-6)
Note: Notice that only six (6) 8-32 x 1” phillips machine screws are used and that the VS. Slalom control panel is slightly off center. This allows the VS. Slalom control panel to be mounted without disassembly.
  • Trademarks of Bally Midway Manufacturing Inc.
Page 9

For LEFT slde vse mkidle row of holes.

& | 1-6

  • Mounting the Ski Base to the Cabinet (These steps are for all cabinets) A. Slide the ski base forward until it touches the bottom face of the cabinet. B. Center the ski base between the side panels. (See Illustration 2-1) C. Using the base to cabinet bracket as a template, mark the three (3) hole locations on the cabinet. D. Slide the ski base away from the cabinet and drill three (3) 3/16” holes at the locations marked. . Slide the ski base forward and install the three (3) No. 14 x 3/4” hex tapping screws, fastening the bracket to the cabinet. (See Illustration 2-2) F. Adjust the ski base so it does not interfere with the cabinet when rocked back and forth. Then securely tighten the two (2) 1/4” x 20 (k lock) hex nuts. (See Illustration 2-1 and 2-2) G. Remove the two (2) 1/4- 20 x 1-1/2” carriage bolts and the two (2) 1/4 x 20 (k-lock) hex nuts from the ends of the poles. H. Place the ends of the poles into the slotted pole brackets and align the holes with the slots. (See Illustration 2-1) |. Replace the two (2) carriage bolts and the two (2) nuts removed in Step (G) and tighten securely. (See Illustration 2-1) m
Note: Be careful not to damage the wire harness in the right pole. J. Connect the three pin connector on the right pole. K. Slide the pole covers down and install the eight (8) 6-32 x 3/8” button head screws securing the pole covers to the pole brackets. (See Illustration 2-1)

‘Thread carriage bolt and tighten nut after Ski Base is

ROCK FREELY

  • Install the software and header per the instructions contained in the VS.-Pak case.
Page 10

Control Panel Parts V. REORDER PARTS LISTS

ITEMPART NO.DESCRIPTION
1SLMU-23-01Molded Handle
2SLMU-01-22UControl Panel (U)
3SLMU-01-22LControl Panel (L)
4MDSA-23-31Handle Switch (P163C3RU)
5SLMU-23-31Leaf Switch (WICO #15-1242-01)
6TKGU-23-10ASwitch Assembly VL-12
7TMAU-12-18Collar
8MDST-12-241 Player Button (Lt. Blue)
9MDST-12-272 Player Button (Green)
10TKGU-23-34Pal-Nut
1SLMU-23-02Stop/Switch Bracket
12SLMU-23-03Pivot Bracket
13SLMU-23-04Spring Bracket (F)
14SLMU-23-05Spring Bracket (B)
15SLMU-23-06Control Tube
16SLMU-23-07Dual Fixing Plate
17SLMU-23-08Control Panel Fastener Bracket
18SLMU-23-09Extension Spring
19SLMU-23-10Bumper
20SLMU-23-11Control Wire Harness
21SLMU-01-22Control Panel Overlay
22SLMU-23-13End Cap (R)
23SLMU-23-14End Cap (L)
24SLMU-23-15Control Panel Spacer
25SLMU-23-16Control Panel Bar
26SLMU-23-17Control Panel Spacer Gasket
27SLMU-23-18Control Handle Plate
28SLMU-23-19Joystick Pin
29SLMU-23-20E Rings
30SLMU-23-21Nylon Washer
31SLMU-23-23Sealer Strip
Page 11

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 12

Base Assembly Parts

ITEMPART NO.DESCRIPTION
1SLMU-01-01Molded Ski Base
2SLMU-01-02Wooden Ski Base
3SLMU-01-03Journal Bearing Rod
4SLMU-01-04Bearings
5SLMU-01-05Bearing Mount Set
6TKGU-23-10ASwitch Assembly (VL-12)
7SLMU-01-06Wire Harness
8SLMU-01-07Ski Graphics
9SLMU-01-08Pole Stickers
10SLMU-01-09Lower Pole Bracket (A)
aSLMU-01-10Lower Pole Bracket (B)
12SLMU-01-11Base Mounting Bracket
13SLMU-01-12Base to Cabinet Bracket
14SLMU-01-13Pole Covers
15SLMU-01-14Poles
16SLMU-01-15Ski Baskets
17SLMU-01-16Springs
18SLMU-01-17Pole Harness
Page 13

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 14

TUCK

= SNOWPLOW/FREEST YLE

1 PLAYER

2 PLAYER

RIGHT

LEFT

L. GREEN

L. BLUE BLACK

[| [2 | [3 4] [5 [6 | 7 | 9 | 10] 11] 13] WIRING DIAGRAM VS. SLALOM CONTROL HARNESS DRAWING NUMBER Nintendo of America Inc. MGS-SL

Page 15

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 16

PRINTED IN U.S.A.