CATHODE RAY TOMES

PlayStation 2 Level-1 Service and Procedures Manual (Version 5.0)

PlayStation 2 (Sony, 2000) · Service Manual · 28 pages · 8 sections · original scan

Page 1

PlayStation®2

SCPH-30000 series SCPH-35000 series SCPH-30000R series SCPH-39000 series

SCPH-50000/50000SS/50000AQ series

SERVICE MANUAL Level-1

vice & Procedures Manual / Version 5.0 Jan 2004

SPECIFICATIONS

General Power requirements 220-240 V AC, 50/60 Hz for SCPH-30002D/-30003D/-300004D -35002/-350003/-350004 Inputs/Outputs on the rear

NOTE: READ THIS DOCUMNENT IN CONJUCTION WITH THE LATEST SERVICE GUIDELINES ISSUED BY SEC

HDD by slot (1)

Outputs on the rear AV Multi out port (1) RGB, Yeber, Y/C, Composite-video, Power consumption Audio-L/R, XGA 50W Digital out port (1) for SCPH-30002D/-30003D/-300004D Optical audio -35002/-350003/-350004 Dimensions Supplied accessories 301 x 78 x 182 mm (w/h/d) AC power cord (1) Mass Euro-AV connector (1) 2.4 kg for SCPH-30003/4 & 35003/4 SCPH-30003/4 R & SCPH-39003/4 Inputs/Outputs on the front Controller ports (2) Memory Card slots (2) USB ports (2) $400 (I-Link) port (1) SCPH-50003/4 & SS & AQ A/V connecting cable (1) Dualshock2 Analog controller (1)

DISC (GT3) for SCPH-35002/-350003/-350004

Page 2

TABLE OF CONTENTS

SCPH-30000 series and SCPH-35000 series GH013 (31/41) MOUNT on board

SAFETY-RELATED COMPONENT WARNING 3

GENERAL INFORMATION 4

  • SERVICE NOTE/CONDITIONS 4 Conditions 4 Fault Information & FAQ 4 Inner Carton Reorder 4
  • WARRANTY 4 Service Warranty 4 Reimbursement: 4
  • APPLICABLE MODELS 4

4, LEVEL-1 SERVICE SPECIFICATION 4

  • SPARE PARTS REORDERS 4
  • WARRANTY SEAL CONTROL 5
  • REPORTING (WARRANTY DATA ENTRY) 5
  • REMOVAL OF STUCK DISC 5-6
  • REPAIR PARTS LIST 7 Exploded Views 7-24 SCPH-30002/30003/30004 (c, C’) 7 Overall and Main Block 7 MD Block 8 Switch Block 9

SCPH-30002/30003/30004 (D, D’) 10 Overall and Main Block 10 MD Block 1. GB-003/GB-004 and Place Assy Block 12 Fan and Rear Panel 12 Switch Block 13

SCPH-30002R/30003R/30004R (F) 14 Overall and Main Block 14 MD Block 15 Switch Assy Block 16 Power Switch, Fan and Rear Panel 17

SCPH-39002/39003/39004/39008 (G) 18 Overall and Main Block 18 MD Block 19 Switch Assy Block 20 Power Switch, Fan and Rear Panel 21

SCPH-50002/3/4/8 & 50002/3/4/8SS & 500002/3/48Q (H) Overall and Main Block 22 MD Block 23 Boards Section 24

SCPH-50002/3/4/8 & 50002/3/4SS (1) Overall and Main Block 25 MD Block 26

PS2 Peripherals 27

  • QUALITY CONTROL TEST 28
Page 3

SAFETY-RELATED COMPONENT WARNING Components identified by mark A and in the parts list are critical to safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual

SAFETY-RELATED COMPONENT WARNINC COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SONY COMPUTER ENTERTAINMENT DEMANDS THAT AT NO TIME SHOULD A MOTHERBOARD BE EXCHANGED FROM ONE CONSOLE TO ANOTHER. NO MCB PARTS ARE INCLUDED ON LEVEL-1 REPAIR.

IMPORTANT _| Do NOT touch any PlayStation®2 parts not listed on this manual.

Replace the battery with a Sony CR2032 battery. Use of any other type of battery may present the risk of fire or explosion. The battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire.

AUTION, The use of optical instruments with this product will increase eye Hazard. As the laser beam used in this CD/DvD player is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.

CAUTION_| Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

When power is ON, Don’t touch to Power supply block, AC-inlet, Power switch and so on, not to get an electric shock at repair.

When current is supplied, Some of part surface temperature like EE, GS, Regulater-IC, power supply, Optical device and so on. These part surface is become high temperature condition. When it repair, don’t touch them at a time during it surface is high temperature condition to take prevent against burning. Do repair after it is cooled down enough.

Some of the above safety te is NOT applicable to Level

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer:

  • Check the area of your repair for unsoldered or cold-soldered connections. Check the entire board surface for solder splashes and bridges.
  • Check the inter board wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
  • Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
  • Look for parts, which, though functioning show obvious signs of deterioration. Point them out of the customer and recommend their replacement.
  • Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
  • Check the b+ voltage to see it is at the values specified.
  • Check the antenna terminals, metal trim, “metalized” knobs, screws, and all other exposed metal parts for ac leakage.

NOTIFICATION for envi This model is CR2032 lithium battery onboard inside on the GD MOUNT as Timer backup power. ©R2032 life may be about 5 to 8 years so you have very few need for changing to new one. But if you have necessary to replaced to new one or disassemble for scrapping, you have to keep your country low, regulation, standard, etc. of environmental assessment and safety.

Page 4

GENERAL INFORMATION NOTICE: Copyright by Sony Computer Entertainment Inc. All rights reserved. No reproduced and transferred required except permission by Sony Computer Entertainment Inc. No commercial use and rental required.

REVISIONS: This manual compiled by first edition of SCPH-30000 series and SCPH-35000 series design data. Design and Specification will be subject to changed without notice. The latest versions of service manual, Technical memo, and Technical information should be used together.

1. SERVICE NOTE/CONDITIONS Level-1 service is only allowed by Sony Service Centres (SSC) or dedicated Authorised Service Centre (ASC) ***. Other type of repair still has to be carried out by SEC-ROE as appropriate jigs or tools are not available to ssc/asc ™**.

1.1. Conditions

notel . ssc and ASC manual; can only perform PlayStation®2 Level-1 repair as described in this

  • It is strictly prohibited to perform any Level-2 and/or Level-3 repairs on PlayStation®2 units;
  • Level-2 repairs must only be performed by SEC—ROE (or SSC/ASC authorised by SCEE)
  • Level-3 repairs must only be performed by SEC-ROE;
  • Any PlayStation®2 unit submitted to any kind of abuse repair will never be classified as ‘in warranty’; . Units sent to SEC-ROE for Level-2 and/or Level-3 repair that shows any evidence of abuse’ will not be compensated;
  • SSCs and ASCs ™***! must have an appropriate Warranty Seal Control procedure covering the following areas: inventory control, process, audit trail and replenishment of stock (please refer to paragraph six in this manual for more details).

1.2. Fault Information & FAQ Sony Computer Entertainment Europe (SCEE) will provide Fault Information and Frequent Asked Questions through the Technical Service Extranet site (http: //tech.scee.net/tech.nsf). This is a secured site and can only be accessed by personnel authorised by SCEE (please contact SCEE if you require access to this system).

1.3. Inner Carton re-order In the case of defective units arriving at SSC or ASC without the original inner carton: SCEE will make ‘brown’ inner cartons available to order by SOSA Central Warehouse. For more information contact SOSA Central Office. Brown inner cartons can be used for returning consoles repaired locally and as a transportation box to SEC-ROE. notel

? abuse: any units missing original components, having additional components (e.g. modifying chips) and/or physical liquid damage.

WARRANTY

Service Warranty The warranty on Level-1 repaired PlayStation®2 should be set to 90 days. Repaired units are eligible to free of charge re-repair within the 90 days warranty.

I/W Reimbursement system In case service is carried out in-warranty, please proceed for compensation according to the standard Warranty Reimbursement rules, outlined in the SEC-ROE Warranty Rulebook.

APPLICABLE MODELS This Level-1 Service Manual is applicable to the following PlayStation®2 models:

  • SCPH-30002 /SCPH-30003 /SCPH-30004 (c)
  • SCPH-30002 /SCPH-30003 /SCPH-30004 (D)
  • SCPH-35002 /SCPH-35003 /SCPH-35004 (D)
  • SCPH-30002R/SCPH-30003R/SCPH-30004R (F)
  • SCPH-39002 /SCPH-39003 /SCPH-39004/SCPH39008 (G)
  • SCPH-50002/3/4/8 & SCPH-50002/3/4 ss (a)

LEVEL-1 SERVICE SPECIFICATION

Definition Level-1 service is only allowed by SSC or dedicated ASC ts! and specified as follows:

  • Cosmetic and easy repairs using level-1 spare parts mentioned in this manual;
  • Replacement of dedicated parts, such as power supply module, terminal board, etc. (please refer to this manual for a full list of dedicated parts);
  • Adjustment of mechanical parts (NOT on optical block);
  • Removal of stuck disk;
  • No Problem Found (NPF).
Page 5
  • SPARE PARTS REORDERS ssc and asc ™* are only authorised to order spare parts listed in this manual. Spare parts should be ordered through existing WRPCE system/procedures. For more information on parts reorders, please refer to SEC-ROE guidelines/procedures.

“® “Where no SSC is present in the country

Repairs must be controlled by the use of Warranty Seals (Part Number: 3-066-498-01, Tape/Void). Warranty Seals must be strictly controlled. All countries wishing to perform Level-1 repair on PlayStation®2, as described in this manual, must submit appropriate Warranty Seal Control procedures covering the following areas: inventory control, process, audit trail and replenishment of stock.

To ensure that Warranty Seals are controlled properly, each SSC and Asc *°*** must have a nominated member of staff who is responsible for these parts. They should carry out the following functions:

  • Confirm that the service centre inventory accurately represents the true stock level when reported to SCEE;
  • To report promptly any loss due to damage, theft, defective application or unforeseen incident;
  • This person will also be responsible for the periodic reporting to SCEE, and should maintain the local audit files to be examined by SCEE as part of a stock inventory audit.
  • ssc and acs “*! must re-seal all PlayStation®2 units that could not be repaired locally (Level-1 repair) before shipping the unit to SEC-ROE for Level-2/Level-3 repair. Reimbursement will not be granted for PlayStation®2 units arriving at SEC-ROE without warranty seal (even if in-warranty).
  • REPORTING SCEE must obtain Level-1 repair information from all countries performing Level-1 repairs locally. Monthly reports will be extracted from ESQI-line, however it is imperative that PlayStation®2 is reported on a “model type” basis (e.g. C-model, D-model, etc). Information must be entered in the ESQI-line in the following format: Example:
  • Console SCPH-30004 type D = SCPH-30004D . Console SCPH-30004R type D = SCPH-30004RD How to identify model type: All Engineers should be able to identify consoles by Model type (e.g. "C","D","F","G"), if not, model type can be identified on the number plate on the “right bottom left hand corner” next to a number with the following format: "3-070-933-01 D" (this last digit refers to the model type)
  • REMOVAL OF STUCK DISC
IMPORTANT NOTE: PlayStation®2 unit must always be handled in ESD-safe conditions:
  • Workbench with anti-ESD mat, connected to earth
  • Technician should wear wrist/ankle strap, connected to any-ESD-mat

In the case, both, power and loading mechanism are active: Connect the PlayStation®2 unit to the power and switch the unit on at the back. When the red LED at the front side is blinking, push this button and the unit will switch one. Disc can be removed by pushing the eject button.

In case power or loading mechanism is not active:

“=

  • Remove HDD Bay lid at the backside of
  • Remove tape void at backside of the the unit. unit.

“ere “where no SSC is present in the country

Page 6

guano son sme =e sigumcemuae. aauaa

  • Remove all the caps and screws of the bottom cabinet very carefully (avoid physical/cosmetic damage on cabinets)

Saran cont saaa8 erroneous uy saaa8 Yasar rea aod a

eee

  • Remove the two long screws on the upper 5. Remove the caps of the upper cabinet cabinet carefully carefully

ern COEF Scereacaun 99 Soonetneee ees ‘SSiemvcrmacavea ay

° S

  • Remove the screws of the upper cabinet 7. Disconnect the power switch from the upper cabinet

seca mencner Levey maacK Ay aaa = ‘i Oren : ' a

8. Remove the 4 screws of the MD-block 9. Lift the pulley bracket assy and

remove the software

  • REPAIR PARTS LIST/EXPLODED VIEWS

Main parts/assembles, which are used by Level-1 centres: All cosmetics, fan, power supply, ribbon cables, controller port connector and various mechanical components.

The mechanical parts with reference on the exploded view (below) with a respective part number on the spare parts list are supplied to level-1 repair centres.

The mechanical parts with reference on the exploded view (below) but without a respective part number on the spare parts list are not supplied to level-1 repair centres.

Page 7

REPAIR PARTS LIST — EXPLODED VIEWS — SCPH-30002/30003/30004 (C, C’)

Overall and Main Block

CAUTION

The components identified by mark 2. or dotted line with mark. 4 are critical for safety. Replace only with part number specified.

Ref-No. Part No. 1-468-565-21 1-528-174-41

1-694-767-11 1-763-480-11 1-771-995-12 1-792-491-21 3-066-489-01 3-059-622-02 3-059-626-03 3-059-627-01 3-325-679-21 X-3951-398-1 X-3951-498-1 X-3951-099-1 1-680-147-11 X-3951-317-1 3-066-498-01 1-757-588-11 1-757-590-11 1-757-589-11 Description Remark POWER BLOCK PS2 BATTERY, LITHIUM OTHER NON-PS2 “LITHIUM CR2032 (CR2032 TYPE) TYPE BATTERY” MAY BE USED. TERMINAL BOARD (FRONT) Dc. FAN SWITCH, POWER (WITH AC INLET) CABLE, FLEXIBLE FLAT (FFC-290) SHIELD (B) SCREW (M3X54), HEAD TAPPING COVER, SCREW CAP SCREW, TAPPING +BV 3X12 COVER ASSY, COVER ASSY, PLATE ASSY, PWB, FP-324 LID ASSY TAPE, VOID CABLE, FLAT CABLE, FLAT CABLE, FLAT LOWER UPPER ORNAMENTAL FLEXIBLE

(FFC-308) (FFC-310) (FFC-309) Place code #00 #25GD

#17 #74 #00 #12 #16 #87 #22 #22 #87 #87 #87 #87 #12 #87 #87 #12 #12 #25GD

Page 8

REPAIR PARTS LIST — EXPLODED VIEWS — SCPH-30002/30003/30004 (C, C’)

MD Block

CAUTION Thare are 2 taps behind Optical device for prevent the damage from static eboctricty. these are usually shored by solder whan it shipping factory. When You use the Optical device for repair, You have to open fe 2 taps by matting solder In 8 case of the alide-cam (Ret.36) or the rubber belt (Ral.39) in the (gear box assy broken, The side-cam or The rubber belt should be ‘exchanged itsal, not Gear box ansy. When you exchange the feed DC-motor or Sub-chassis assy for ‘repair, You have to groase Fic (SG-474BY or a similar articles) up to Feed motor sledding goar and Sub-ehaft.

Ref-No. Part No. Description Remark Place code 17 3-060-400-01 TAPPING (B2x6.5) #10 27 X-3951-154-2 BRACKET ASSY, PULLEY #10 28 X-3951-153-2 TRAY ASSY #10TR 29 X-3951-156-3 BOX ASSY, GEAR #10GB 31 1-680-370-11 PWB, FLEXIBLE #10

Page 9

REPAIR PARTS LIST — EXPLODED VIEWS — SCPH-30002/30003/30004 (C, C’)

Switch Block

Ref-No. Part No.

3-059-665-03 3-059-666-05 7-685-105-11 A-6712-830-A Description Remark

BUTTON, SWITCH BRACKET, SWITCH TPG +P 2X8, TYPE 2, NON-SLIT SW-355 MOUNT Place code

#2580 #2580 #2580 #2580

Page 10

REPAIR PARTS LIST — EXPLODED VIEWS — SCPH-30000 series and SCPH-35000 series (D, D’)

Overall and Main Block for SCPH-30002D/30003D/30004D/35002/35003/35004

CAUTION

The components identified by mark 2s or dotted line with mark. A. are critical for safety. Replace only with part number

CAUTION Don't lose the insulating sheet when assemble the console.
CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Ref-No. Part No. Description Remark Place code 60 1-468-605-11 | POWER BLOCK #00 62 1-694-676-21 TERMINAL BOARD (FRONT) #17 62 1-694-729-21 TERMINAL BOARD (FRONT) #17 62 1-694-769-31 TERMINAL BOARD (FRONT) #17 75 3-059-626-03 COVER, SCREW #22 76 3-059-627-01 CAP #22 84 3-067-170-01 TAPE (20X20), HARNESS STOPPER #87 93 X-3951-722-1 COVER ASSY, LOWER #87 106 X-3951-317-1 LID ASSY #87 112 3-066-498-01 TAPE, VOID #87 151 1-757-934-11 CABLE, FLEXIBLE FLAT (FFC-011) #12 151 1-757-934-21 CABLE, FLEXIBLE FLAT (FFC-011) #12 152 1-823-341-11 CABLE, FLEXIBLE FLAT (FFC-015) #12 152 1-823-341-21 CABLE, FLEXIBLE FLAT (FFC-015) #12 153 1-961-160-21 HARNESS (HS-059) #12 158 3-068-675-02 | SHIELD (HDD) #87 162 3-069-212-01 TAPE, HARNESS STOPER #16 BV312 3-325-679-21 SCREW, TAPPING +BV 3X12 #87 M354 3-059-622-02 SCREW (M3X54), HEAD TAPPPING #87 M360 3-069-168-01 TITE (CZN), M3X6 +BV S #87

Page 11

REPAIR PARTS LIST — EXPLODED VIEWS — SCPH-30000 series and SCPH-35000 series (D, D’)

MD Block

Ref-No. Part No. Description Remark Place code

17 3-060-400-01 TAPPING (B2x6.5) #10 27 X-3951-609-1 BRACKET ASSY, PULLEY #10 28 X-3951-608-1 TRAY ASSY #10TR 31 1-680-370-12 PWB, FLEXIBLE #10

Page 12

REPAIR PARTS LIST — EXPLODED VIEWS — SCPH-30000 series and SCPH-35000 series (D, D’)

GB-003/GB-004 and Plate Assy Block

Ref-No.

GB003

GB004

GBO00S

GB006

Fan and

Ref-No.

BV312 Part No. Description Remark 1-528-174-41 BATTERY, LITHIUM (CR2032 TYPE) 1-961-160-21 HARNESS (HS-059 A-6712-923-A GB-003 MouNTUse for combine A-6712-984-A GB-004 MoUNTUse for combine A-6712-996-A GB-005 MoUNTUse for combine A-6712-984-A GB-006 MoUNTUse for combine

Rear Panel Block

Part No.

1-763-480-23 1-763-544-22 1-763-756-11 1-771-995-31 1-786-209-21 3-068-676-12 3-325-679-21 Description Remark

DC. FAN FAN, DC FAN, DC SWITCH, POWER (WITH AC INLET) SWITCH, POWER (AC INLET) PANEL, REAR SCREW, TAPPING +BV 3X12 with GHO10. with GHO12. with GH013. with GHO14.

Place code

#74 #74 #74 #00 #00 #87 #87 Place code #25GB #12 #25GB #25GB

#25GB #25GB

Page 13

REPAIR PARTS LIST — EXPLODED VIEWS — SCPH-30000 series and SCPH-35000 series

  • Switch Assy Block (D, D’)

Ref-No. Part No. Description Remark code

92 A-6705-338-A | SWITECH BLOCK ASSY Used for combine with GHO010. 92 A-6705-424-A | SWITECH BLOCK ASSY Used for combine with GH013. 92 A-6705-401-A SWITECH BLOCK ASSY Used for combine with GH012/GH014. 50 3-059-665-03 BUTTON, SWITCH 51 3-059-666-05 BRACKET, SWITCH 51 3-066-494-01 BRACKET, SWITCH 52 7-685-105-11 TPG +P 2X8, TYPE 2, NON-SLIT

Page 14

Overall and Main Block for SCPH-30002 R(AU3) /-30003 R(CEK) /-30004 R(CEL) ( F )

Ref-No.

BV312 BV316 M354 M360 Part No.

1-468-605-11 1-468-605-21 1-528-174-41 1-694-873-11 1-694-874-11 1-694-875-11 3-059-626-03 3-059-627-01 3-067-170-01 X-3951-722-2 X-3951-099-1 3-070-847-11 3-066-498-01 1-757-934-11 1-757-934-21 1-757-934-31 1-823-341-11 1-823-341-21 3-071-971-01 3-071-973-01 3-069-212-01 3-325-679-21 3-325-679-91 3-059-622-02 3-069-168-01 GHO15(12/22

Description Remark

POWER BLOCK for 220-240V AC POWER BLOCK for 220-240V AC BATTERY, LITHIUM (CR2032 TYPE) TERMINAL BOARD (FRONT) TERMINAL BOARD (FRONT) TERMINAL BOARD (FRONT) COVER, SCREW CAP TAPE (20X20), HARNESS STOPPER COVER ASSY, LOWER PLATE ASSY, ORNAMENTAL LID TAPE, VOID CABLE, FLEXIBLE FLAT (FFC-011) CABLE, FLEXIBLE FLAT (FFC-011) CABLE, FLEXIBLE FLAT (FFC-011) CABLE, FLEXIBLE FLAT (FFC-015) CABLE, FLEXIBLE FLAT (FFC-015) SHEET, INSULATING SHIELD HDD (F) TAPE, HARNESS STOPPER SCREW, TAPPING +BV 3X12 TAPPING +BV 3X16 SCREW (M3X54), HEAD TAPPING TITE (CZN), M3X6 +BV S Place

#00 #00 #25GH #17 #17 #17 #22 #22 #87 #87 #87 #87 #87 #12 #12 #12 #12 #12 #16 #87 #87 #87 #87 #87 #87

Page 15

MD Block for SCPH-30002 R(AU3) 30003 R(CEK) /-30004 R(CEL) ( F )

MD Block

Ref-No. Part No. Description Remark Place

17 3-060-400-01 TAPPING (B2X6.5) #10 27 X-3952-059-1 BRACKET ASSY, PULLEY #10 28 X-3952-060-1 TRAY ASSY #10TR 31 1-680-370-21 PWB, FLEXIBLE #10

Page 16

Switch Assy Block for SCPH-30002 R(AU3) /-30003 R(CEK) /-30004 R(CEL) ( F )

Switch Assy Block

Ref-No. Part No.

3-059-665-03 3-059-666-05 3-066-494-01 7-685-105-11 A-6715-500-A A-6714-500-A

A-6787-465-A A-6787-466-A Description Remark

BUTTON, SWITCH BRACKET, SWITCH BRACKET, SWITCH TPG +P sw-367 SW-367

sw-367 SW-367 2x8, TYPE 2, NON-SLIT COMPL MOUNT

COMPL (VA) MOUNT (VA) Place

#25SW #25SW #25SW #25SW #25SW

#25SW

Page 17

Power Switch, Fan and Rear Panel Assy Block for SCPH-30002 R(AU3) /-30003 R(CEK) /-30004 R(CEL) ( F )

Power Switch, Fan and Rear Panel Assy Block

Ref-No. Part No. Description Remark Place

63 1-763-480-31 DC.FAN #74 63 1-763-554-31 FAN DC. #74 63 1-763-756-21 FAN DC. #74

64 1-771-994-31 SWITCH, POWER (WITH AC INLET) for SCPH-30001 R #00 64 1-786-209-21 SWITCH, POWER (WITH AC INLET) for SCPH-30002 R /-30003 R /-30004 R SWITCH, POWER (WITH AC INLET) for SCPH-30005 R /-30006 R /-30007 R

159 3-071-901-01 PANEL, REAR for SCPH-30001 R/-30005 R #87 159 3-071-901-11 PANEL, REAR for SCPH-30002 R/-30003 R/-30004 R SCPH-30006 R/-30007 R #87

BV312 3-325-679-21 SCREW, TAPPING +BV 3X12 #87

Page 18

Overall and Main Block for SCPH-39002 / 39003 /39004 /39008 ( G )

Sas ec Aa 32 Eichawoye “Sa

‘Shiels (A) Avwy Block

See GHOIMDI®D page

/

‘CAUTION Devt tose the insukating sheet vihen ansemble the console,

  • GHe

Ref-No. Part No. Description Remark Place code

60 1-468-605-31 POWER BLOCK for 220-240V AC #00 61 1-528-174-41 BATTERY, LITHIUM (CR2032 TYPE) #25GH 62 1-694-875-11 TERMINAL BOARD (FRONT) #17 75 3-059-626-03 COVER, SCREW #22 16 3-059-627-01 CAP #22 84 3-067-170-01 TAPE (20X20), HARNESS STOPPER #87 92 A-6787-644-A SWITCH BLOCK ASSY #87 93 X-3951-706-2 COVER ASSY, LOWER #87 95 X-3951-099-1 PLATE ASSY, ORNAMENTAL #87 106 3-070-847-01 LID #87 112 3-066-498-01 TAPE, VOID #87 112 3-079-117-01 TAPE, VOID (For SCPH-39008) #87 151 1-757-934-11 CABLE, FLEXIBLE FLAT (FFC-011) #12 152 1-823-341-11 CABLE, FLEXIBLE FLAT (FFC-015) #12 157 3-071-971-01 SHEET, INSULATING #16 158 3-071-973-01 SHIELD HDD (F) #87 162 3-069-212-01 TAPE, HARNESS STOPPER #87 B265 3-069-170-01 TAPPING (B2X6.5) #87 BV312 3-325-679-21 SCREW, TAPPING +BV 3X12 #87 BV316 3-070-296-01 TAPPING +BV 3X16 #87 M354 3-059-622-02 SCREW (M3X54), HEAD TAPPING #87 M360 3-069-168-01 TITE (CZN) M3X6 +BV S #87 7250 3-071-976-01 TAPPING (2X5) #87

Page 19

MD Block for SCPH-39002 / 39003 / 39004 /39008 ( G )

MD Block

Ref-No. Part No. Description Remark

17 3-060-400-01 TAPPING (B2X6.5) 27 X-3952-059-1 BRACKET ASSY, PULLEY 28 X-3952-060-1 TRAY ASSY 1-680-370-22 PWB, FLEXIBLE BOTTOM VIEW)

TAP

Place code

#10 #10 #10TR #10

Page 20

Switch Assy Block for SCPH-39002 / 39003 / 39004 / 39008 ( G )

Ref-No. Part No. Description

50 3-059-665-03 BUTTON, SWITCH 51 3-059-666-05 BRACKET, SWITCH 51 3-066-494-01 BRACKET, SWITCH 52 7-685-105-11 TPG +P 2X8, TYPE 2, NON-SLIT

53 A-6787-551-A COMPLETE PWB (VA), SW-373

53 A-6787-553-A COMPLETE PWB (VA), SW-373(VA)

53 A-6787-645-A COMPLETE PWB (VA), SW-382

53 A-6787-647-A COMPLETE PWB (VA), SW-382(VA)

53 A-6787-976-A COMPLETE PWB, SW-393

53 A-6787-978-A COMPLETE PWB (VA), SW-393

= 20 - Remark

with

with

with

with

with

with GHO18

GHO18

GHO19

GHO19

GHO22

GHO22 MOUNT.

MOUNT.

MOUNT.

MOUNT

MOUNT.

MOUNT. Place code

#25SW #25SW #25SW #25SW

#25SW

#25SW

#25SW

#25SW

#25SW

#25SW

Page 21

Power Switch, Fan and Rear Panel Assy Blockfor SCPH-39002 / 39003 / 39004 / 39008 ( G )

Ref-No. Part No. Description Remark Place code

63 1-763-480-31 DC. FAN #74 64 1-786-209-21 SWITCH, POWER (WITH AC INLET) #00 159 3-071-901-01 PANEL, REAR #87 BV312 3-325-679-21 SCREW, TAPPING +BV 3X12 #87

Page 22

Overall and Main Block for SCPH-50002 /50003/50004 /50008 (H&HSS)

Ref-No. Part No. Description

1 169487513 TERMINAL BOARD (FRONT) 2 307455511 SCREW, +BV TAPPING 3 308452101 SCREW (M3X27), TAPPING 4 307454801 COVER, SCREW 5 307455501 SCREW, +BV TAPPING 6 307454901 cAP 7 307455601 SCREW, BRAZIER HEAD P TIGHT 8 308450601 PANEL (H), REAR 9 178634551 SWITCH, POWER (WITH AC INLET) 10 178700911 FAN, D.C. 13 307455001 LID 14 X39535861 COVER (H) ASSY, LOWER (H) 14 X39537401 COVER (H) ASSY, LOWER Silver (H SS) 14 X39542641 COVER (H) ASSY, LOWER Aqua (H AQ) 15 306625301 TAPE, VOID

Page 23

MD Block for SCPH-50002 / 50003 / 50004 /50008 (H&HSS)

Ref-No. Part No. Description

102 306040001 TAPPING (B2X6.5) 108 308452201 TRAY (H) 128 X39535891 BRACKET (H) ASSY, PULLEY

Page 24

Boards Section for SCPH-50002 / 50003 /50004 / 50008 (H&HSS & HAQ)

TITE (CZN), M3X6 +BV S POWER BLOCK (SWITCHING REGULATOR) SHEET (H),INSULATING CABLE, FLAT (FFC-011) SCREW (B2X6.5B), TAPPING

SHEET (A), ELECTRIC HEAT SHIELD (A) (H) ASSY

PLATE (H) ASSY, ORNAMENTAL (H) PLATE (H) ASSY, ORNAMENTAL SILVER (H SS) PLATE (H) ASSY, ORNAMENTAL AQUA (H AQ) CABLE, FLEXIBLE FLAT (FFC-019)

Ref-No.Part No.Description

54 307455301 55 146875821 56 308451901 57 175793411 58 308452001

61168037023FLEXIBLE BOARD

62 308029301 63 X39535881

65308450901BUTTON (H), SWITCH

66 X39535871 66 X39537411 66 X39542651 68 182715011

69308558901SPACER (H)

70 308029401 SHEET (DRIVER), ELECTRIC HEAT

Page 25

Overall and Main Block for SCPH-50002 / 50003 / 50004 / 50008 (1&1SS)

Bad

Ref-No. Part No. Description 52 306040001 TAPPING (B2X6.5) 53 A6800233A SW-398 BOARD, COMPLETE 60 146875821 POWER BLOCK (SWITCHING REGULATOR) 60 146875841 POWER BLOCK (SWITCHING REGULATOR) 60 146875921 POWER BLOCK (SWITCHING REGULATOR) 60 146876011 POWER BLOCK (SWITCHING REGULATOR) 62 169487311 TERMINAL BOARD (FRONT) 62 169487312 TERMINAL BOARD (FRONT) 62 169487513 TERMINAL BOARD (FRONT) 62 169487521 TERMINAL BOARD (FRONT) 63 178700911 FAN, D.C. 63 178703511 FAN, D.C. 63 178703611 FAN, D.C. 64 178620931 SWITCH, POWER (WITH AC INLET) 64 178634551 SWITCH, POWER (WITH AC INLET) 75 307454801 COVER, SCREW 75 308587701 COVER, SCREW 50002/3/4SS 76 307454901 CAP 93 X39535861 COVER ASSY, LOWER 50002/3/4 93 X39537401 COVER ASSY, LOWER 50002/3/4SS 95 X39533051 PLATE (H) ASSY, ORNAMENTAL 95 X39537411 PLATE (H) ASSY, ORNAMENTAL 50002/3/4sSS 106 307589901 TAPE, VOID 151 175793411 CABLE, FLAT (FFC-011) 158 308451301 SHIELD (HDD) (H) 159 308450601 PANEL (H), REAR BV312 307029601 TAPPING +BV 3X16 CR2032 52817451 BATTERY, LITHIUM (CR2032 TYPE)

Page 26

MD Block for SCPH-50002 / 50003 /50004 / 50008

BRACKET ASSY, PULLEY Ref-No. Part No. Description

17 306040001 TAPPING (B2xX6.5) 27 X39520591 28 308452201 TRAY (H) 31 168037022 PWB, FLEXIBLE (1&1SS)

Page 27

PS2 Peripherals

CONNECTOR, CONVERSION

ANALOG CONTROLLER(DUAL SHOCK 2) ANALOG CONTROLLER(DUAL SHOCK 2) SILVER Ref-No. Part No. Description

AC EURO 157513182 CORD, POWER

CONV 157329111

AV 179202831 AV CABLE

CONT 182355212 CONT 182770211 CONT 182881911 ANALOG CONTROLLER(DUAL SHOCK 2) AQUA

Page 28
  • QUALITY ASSURANCE TEST (QA TEST)

Part No. Description Remark Ref-No.

n/a J-250-407-3A SVD 4514 n/a J-250-407-0A SCD 4515

n/a J-2504-118-A — SVD-E94075 SCPH 39003/4, SCPH 50003/4/8 & SS & AQ

QA-Test-disc is supplied as a spare part. If the units pass test with PS-game, PS2-game and DVD, EVERY unit needs a QA-test and has to pass the QA-test. After the QA-test, an aging-test with a PlayStationR2-demo disc needs to be done during two hours. If the unit passes this test, the unit can be considered as repaired and can be returned to the customer. The following QA-Test guidelines should be followed:

To perform the QA-test, the following equipment is required:

Note: Test-CD: SCD 4515 and SVD 4514 and SVD-E94075 (available as spare part) 2 grey (PS) + 2 black (PS2) memory cards (not supplied)’ TV (not supplied) ? Amplifier with OP dig out connection + loudspeaker (not supplied) * USB-cable (not supplied) * Optical Digital Cord (not supplied)’ 2 Dual Shocks PS2

1 Please use existing stock ? whese equipments are generic equipment and should already be available at SSC and ACS.

Process-description:

  • Connect Power Cord, AV-cable & optical digital cord to the unit (Backside);
  • Connect USB-cable and insert the 2 grey memory cards and Dual Shocks (Front side);
  • Switch the Power ON & push the reset button;
  • Insert SCD 4515 test disc;
  • Check Audio and Video: CARD 0 and CARD 1 must be: OK;
  • Push R1 button on Dual Shock and check Audio and video;
  • Push Ll button on Dual Shock and check Audio and video;
  • Remove SCD 4515, insert SVD 4515 and push the reset-button;
  • Replace grey memory cards with the black ones;
  • Check Screen “ PS2 check disc v2.00" All items must be OK;
  • Push L1, Rl and red O-button together and “ Check V-RAM” OK, push red 0-button again and v- RAM: OK;
  • Push red O-button and check Audio (TV + Loudspeaker) and Video;
  • Push red O-button and check Audio and video;
  • Push red O-button “RD-RAM-test 0.02” OK;
  • Push red O-button “HDD-connector-test” OK;
  • Remove disc and switch off the unit.

Date Written by Approved by

09-Nov-2001

Warllen Duque Mike Nabarro Compliance Manager vice-President of Technical services Sony Computer Entertainment Europe | Sony Computer Entertainment Europe

*** end of page ***