CATHODE RAY TOMES

Xybots TM-313 1st Printing

Xybots (rev 2) (Atari Games, 1987) · Technical Manual · 64 pages · 61 sections · original scan

Page 1

pee mm]! A

lhe A.

ATART

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

AL

ATARI

GAMES

Xybots Operators Manual

with Illustrated Parts Lists

Page 4

© 1987 by Atari Games Corporation All rights reserved No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form ofa phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles, In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari Games Corporation will aggressively enforce its copyrights against any infringers, We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A. 10R Xybots

Page 5

Xybots

Notice Regarding Non-ATARI® Parts

A WARNING A

Use of non-ATARI parts or modifications of any ATARI game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game. © Modify or alter any circuits in the game by using kits or parts zot supplied by Atari Games Corporation.

NOTE

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart] of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. if you suspect interference from an ATARI® game at your location, check the following: © All ground wires in the game are properly connected as shown in the game wiring diagram.

  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground plane, be sure the game printed-circuit boards (PCBs) are properly installed on the EMI Ground Plane. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.

iii

Page 6

Table of Contents Set-Up How to Use This Manual ... 0-66-60. e cece eee teeter eee Inspecting the Game ..... Control and Switch Locations . Setting the Coin and Game Options . Game Play .. Self-Test RAM/ROM Test . . . Switch Test . . Coin Options .. Game Options . Statistics ... Histograms ....... Playfield Test ..... Motion Object Test Alphanumerics Test Color Test Color Purity Test ... Convergence Test . Sound Test

Maintenance Preventive Maintenance ... Preventive-Maintenance Intervals . . Removing the Control Panel Cleaning the Push-Button Leaf Switches Joystick .0 6.6 eee eee ee Cleaning the Coin Mechanism . oe Cleaning the Interior Components ........6 5.6.0 e cece cette eee eee Corrective Maintenance ... Removing the Joystick ..... Disassembling the Joystick . Reassembling the Joystick. . . Removing the Video Display Replacing the Video Display . Removing the Game PCB... Removing the Fluorescent Light. . Removing the Speakers Troubleshooting Troubleshooting Aids .. . Troubleshooting Techniques . . Soldering Techniques Troubleshooting Static-Sensitive Devices . . Illustrated Parts Lists See List of Illustrations that follows.

Xybots Coin Information and Game Statistics Sheet 4-2 Xybots

Page 7

Xybots

List of Illustrations Figure 1-1

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14

Figure 3-1 Figure 3-2 Figure 3-3

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4

Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7

Table 1-1 Table 2-1 Table 2-2 Table 2-3 Table 2-4 Table 2-5 ‘Table 3-1 Control and Switch Locations ...... 2.26. cece cece eee

RAM Test Fails . ROM Test Fails . Switch Test . . Coin Options Game Options . Statistics .... Histograms Playfield Test .. Motion Object Test . Alphanumerics Test Color Test....... Color Purity Test . . Convergence Test . . Sound Test

Leaf Switch and Joystick Removal ....... Joystick Disassembly and Lubrication Control Panel, Video Display, and Speaker Removal ............

Removing IC (Cut-Pin Method) Removing IC Pins .......-......55 Removing Solder from Plated-Through Holes . Removing Solder from Lead Connection Pads . . .

Cabinet-Mounted Assemblies . . Control Panel Assembly .. . Joystick Assembly Switching/Linear (SL) Power Supply Assembly . . Coin Acceptors, Inc. Coin Door Assembly. . Xybots Game PCB Assembly .... . Stand-Alone Audio PCB Assembly . .

List of Tables Game Specifications ... . Faulty RAM Locations . Faulty Upper or Lower Main. ROM Locations Game Option Settings ......... Motion Object Test Description . . Faulty Sound RAM and ROM Locations . . . Recommended Preventive-Maintenance Intervals . . . 5-12

5-22

1-2 2-2

2-4

3-2

Page 8

vi

Safety Summary

‘The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A WARNING A

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded three-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to installa grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the game’s power supply is properly configured for the line voltage in your location. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (i.e., United States) must not be operated in countries with 50 Hz line power (i.e., Europe). ‘The fluorescent light ballast transformer will overheat, causing a potential fire hazard if 60 Hz games are operated on power lines using 50 Hz. Check the product identification label of your game for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS Inall Atari publications, notes, cautions, and warnings have the following meaning:
NOTE —A highlighted piece of information.
CAUTION—Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions. ‘WARNING—Players and/or technicians can be injured or killed if instructions are not followed. (The word WARNING is always surrounded by international warning symbols—triangles with exclamation marks inside of them.) Xybots
Page 9
Scan of page 9

This page is a drawing, shown as the original scan.

Page 10

SevUp

Inspecting the Game

A WARNING A

Do not plug in the game until you have completed the following inspection steps.

Please inspect your Xybots game carefully to ensure that the game is complete and delivered to you in good condition. Figure 5-1 shows the locations of the component Parts of the game. Table 1-1 lists space, power, and environmental requirements. Inspect the factory-assembled game as follows: 1, Examine the exterior of the cabinet for dents, chips, or broken parts.

  • Unlock and open the rear access panel. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors (on the cabinet harnesses) are firmly plugged in. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed connector can damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the corsect fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected.

e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), and

Table 1-1 Game Specifications

Characteristic Specification

Power Consumption 162 V-A, 117 W RMS. Temperature +5° to +38°C (+37° to + 100° F) Humidity Not to exceed 95% relative Line Voltage 102 to 132 VAC (U.S. games) Width 27 in, (69 cm) Depth 34 in. (86 cm) Height 73 in. (185 cm) Weight 302 Ibs. (137 kg)

1-2 Xybots

speakers. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch Locations

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet. (See Figure 5-1.)

Volume Control The volume control is located on the Audio PCB behind the upper coin door. (See Figure 1-1.) The volume control adjusts the level of sound produced by the game.

Coin Counter The coin counter is located on the shelf inside the upper coin door. The coin counter records the number of coins deposited.

Self-Test Switch The self-test switch is located to the left of the volume control on the Audio PCB behind the upper coin door. (See Figure 1-1.) The self-test switch selects the Self-Test Mode to check game operation. Refer to Chapter 2 for a complete description of self-test operation.

Setting the Coin and Game Option Settings

The Xybots coin and game options are set in the Self-Test Mode. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section of the manual describes the theme of the Xybots game and the game play features.

Introduction Xybots is a one- or two-player game with a continuous buy-in feature allowing players to join in at any time. A color-coded control panel (left player/blue and right player/green) and game character allows for instant identification by players. Each player controls a special joystick and two buttons. The joystick is eight-way directional with an independently turning knob for left and right turns. Players use a blaster to “fire” upon the many Xybots in the maze. A button is located on each side of the joystick for both left- and right-handed players. The center button is the “zap.” When this button is pressed, the player can stun all monsters within the player's view.

Page 11

Xybots

Auxiliary Coin Switches SetUp

Self-Test Switch

‘Stand-Alone Audio PCB

a Coin Counter

Figure 1-1 Control and Switch Locations

Play Mode Xybots takes place in the distant future on a planet overrun by a hostile civilization of robots called Xybots. They have created huge underground multi-level cities composed of mazes with locked doors and transporters to connect different areas of the same level. Players must battle the Xybots and reach the exit elevator to advance. In the mazes players find energy pods to restore energy, keys to open doors, and coins to buy valuable supplies in the store. Players enter stores between each level. Some of the supplies purchased are temporary and must constantly be replenished. Every few levels players must face the Master Xybot in a one-on-one duel. If players can beat the Master Xybot, they will be generously rewarded. Only by defeating the Master Xybot can players advance to the next level. The penalty for losing is to be sent back a few levels. The Xybots robots include: ¢ Saucers: Carry coins and energy pods through the maze. They generally run away, but become ‘“‘kamikazes” if cornered. One blast destroys the Saucer.

  • Tanks: Two types. The front-armored type, but vulnerable when it opens its armor to shoot. The sidearmored type, vulnerable from the front or rear.
  • Warriors: Large red robots with enormous firepower, but without extra armor. ¢ Guardians: Similar to the Warriors, but unpredictable. They only appear on the map when players are equipped with a special power. ¢ Flies: Robots with the ability to fly over players’ shots. More skill and timing are required to destroy them.

Maximizing Earnings

Operator options on this game have been kept very simple. You should thoroughly read Chapter 2, Self-Test, for the Coin Options, Game Options, Histograms, and Statistics screens so that you can effectively use the available options. Use the Self-Test screens showing Statistics and Histograms to evaluate game data, and the Game Options screen to make adjustments. (Refer also to the Self-Test chapter for more information on setting options.) The key to maximum earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be Jong enough to give players a good value and ensure repeat play. (Repeat play is crucial to longevity.) The Xybots software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments. If collections seem low or are dropping off, check all player controls and coin mechanisms for proper operation.

Page 12

Set-Up

If earnings seem low, the game is technically sound and the average game time per quarter is under 150 seconds, try changing the game difficulty option to an easier setting. This change will give players more game time for their money. If the average game time per quarter is over 270 seconds, first try changing the game difficulty to a harder setting. If the average game time per quarter is still over 270 seconds after a few weeks, try an even harder setting.

1-4 Xybots

NOTE Be sure to keep the factory default at no if you wish to try other than factory-recommended settings.

After changing the game difficulty settings, it is a good idea to reset the game statistics. The coin information and game statistics should be cleared in self-test by pressing the left start button; this resets the average game time statistic. In addition, the histograms should be cleared by pressing the left start button while displaying the Histogram screen.

Page 13

ee Tea if es an a4 ee : eee) ati

1c é itself and provides visual and auf the condition of the game circuitry

  • Self-test information is displayed on the n’and through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the moncy, or when. you suspect game failure. Thirteen self-test screens provide information pertaining to the game circuits and controls. The game enters the Self-Test Mode after the self-test switch is turned on. The following self-test screens are arranged in the sequence in which they occur when the self-test switch is turned on. After the Sound Test, the sequence starts over with the Switch Test. Turning the self-test switch off at any time during the Self-Test Mode causes the game tG-feturn.to the Attract Mode. Refer to Chapter 1 for the self-te: itch location. cS Be Be Ss ARG,

Brtireg caress = Pees ore See eet ies Ssaeg eee is Sages Civeane ree an ct poi eed

Page 14

Self-Test Xybots

RAM/ROM Test Table 2-1 Faulty RAM Locations

The RAM/ROM Test screens are shown in Figures 2-1 andLocation onVideo Display Char-
2-2. This test provides a visual check of the game RAM,RAM TypeGame PCBacteristic

ROM, and associated circuitry. If the RAM and ROM Test

passes, the display advances to the Switch Test.Upper Video RAM14]Background color is
The RAM/ROM Test is divided into two sections, Thebower Video RAMAESomes bine themes

RAM Test is performed first. If the RAM Test passes after sages may be hard to a six-second delay, the self-test skips to the ROM Test read. The program will without displaying any message. If the RAM fails, a mes- reset if the self-test is adsage will be displayed in the center of the screen as shown. vanced beyond the in Table 2-1. The RAM Test will continue to run until it ROM Test.

passes. If the left Fire button is pressed and released, theUpper Color RAM17KReddish or brightly col-

RAM Test will advance to the next RAM or ROM Test. ored.

Lower Color RAM17JBlues and greens will be

The ROM Test will display no messages and advance to the Switch Test if no errors occur, If a ROM fails, a message is displayed. Table 2-2 shows the location of the failing ROM. If the left Fire button is pressed, and released, the prevalent colors.

the ROM Test will advance to the next ROM. Table 2-2 Faulty Upper or Lower Main ROM Locations

Error Address Location on Game PCB 00000 U=17CD 10000 U=17C/D 20000 U=17B 8000° U=17C/D

  • This message can also occur if there is any error with the custom chip at 14B or its associated circuitry © Color BoM BRD

O-errer

ch Teat verte ail contr

Figure 2-1 RAM Test Fails

Figure 2-3 Switch Test

Switch Test The Switch Test is shown in Figure 2-3. This test checks the condition of the player controls. The joystick movement and the buttons that are checked include: Left Player Up Right Player Up Left Player Down Right Player Down Left Player Left Right Player Left Figure 2-2 ROM Test Fails Left Player Right Right Player Right

2-2

Page 15

Xybots

Left Player Turn Left Right Player Turn Left Left Player Turn Right Right Player Turn Right Left Player Fire Right Player Fire Left Player Start Right Player Start Operate the joysticks and pushbuttons for the right player first, and then the left player. Check that the screen highlights in white the appropriate joystick movement or button that was pressed. Press the left Fire button to obtain the next screen.

Coin Options The Coin Options screen is shown in Figure 2-4. The Coin Options screen indicates the current coin option settings and is used to change those settings. GAME PRICE should have a ted box around it. Move the left joystick right or left to cycle through four game price selections as follows:

  • One Coin (Default)
  • Two Coins ¢ Three Coins

© Four Coins Select the desired value. Note that the default (recommended) setting of One Coin is highlighted in green. Move the left joystick down to move the red box to MUL- TIPLIER. Then move the left joystick right or left to cycle through eight multiplier selections as follows: © 1 Coin Counts as 1 Coin (Default) ¢ 1 Coin Counts as 2 Coins

© 1 Coin Counts as 3 Coins ¢ 1 Coin Counts as 4 Coins

  • 1 Coin Counts as 5 Coin © 1 Coin Counts as 6 Coins

Figure 2-4 Coin Options Self-Test

  • 1 Coin Counts as 7 Coins
  • 1 Coin Counts as 8 Coins

Select the desired value. Note that the default (recommended) setting of 1 Coin Counts as 1 Coin is highlighted in green. Move the left joystick down to move the red box to BO- NUS ADDER. Move the left joystick right or left to cycle through seven bonus adder selections as follows: © None (Default) ¢ 2 Coins Give 1 Extra Coin ¢ 4 Coins Give 1 Extra Coin

  • 4 Coins Give 2 Extra Coins
  • 5 Coins Give 1 Extra Coin

© 3 Coins Give 1 Extra Coin © Free Play Select the desired value. Note that the default (recommended) setting None is highlighted in green. If you replace the EEROM at location 20C/D or a hardware problem occurs, the coin options will switch to the default (green) settings. Jf you want to cancel the coin option changes and restore the original settings, press the left Start button. Press the left Fire button to set the game for the options selected and obtain the next screen. Exiting from the Coin Options screen by turning off the self-test switch will not set the game for the selected coin options.

Game Options

The Game Options screen is shown in Figure 2-5. This screen indicates the current game option settings, and is used to reset the high score table and change the game option settings. Refer to Table 2-3 for the available op-

re Tabie®

in Attroet Mode?

ory Default Settings?

yi tet

Left START betton. inet ed 7 eriginel setting Tree eet ins and exit

Figure 2-5 Game Options

Page 16

Self-Test

Table 2-3 Game Option Settings

Option Name Available Settings

Reset High Score Table No 4 Yes Sounds in Attract Mode No Yes <4 Restore Factory Default Settings No~< ‘Yes Game Difficulty O—Easy

3—Moderate <4

6—Hard 7—Hardest

¢ Manufacturer's recommended settings

tions and the default (recommended) settings. Note that the default settings are highlighted in green. Move the left joystick right or left and note that the settings in the red box change. Select the desired value. Move the left joystick up or down to move the red box to the desired option. Move the left joystick right or left to cycle through all the available game option settings, and select the desired value. Repeat this procedure for the remaining options. Reset High Score Table—The high score table is not reset unless you select Yes.

Sounds in Attract Mode—Sound is played in the Attract Mode unless you select No. Restore Factory Default Settings—If you select Yes and exit from the Game Options Screen by pressing the left Fire button, the game option settings stored in nonvolatile RAM will be cleared and replaced by the manufacturer’s default (recommended) settings when the game enters the Attract Mode.

Game Difficulty—The Game Difficulty settings adjust the difficulty of the Xybots. If you want to cancel the option changes and restore the original settings, press the left Start button. Press the left Fire button to set the game for the options selected and obtain the next screen. Exiting the Game Options screen by turning off the self-test switch will not set the game for the selected options.

Statistics

The Statistics screen appears as shown in Figure 2-6. This screen provides a visual check of the current game statistics. The statistics information is accumulated either from the first time the game was turned on or from the last time Xybots

Figure 2-6 Statistics

the statistics were reset. To reset the statistics information, press the left Start button. The following information appears on the Statistics screen: © Plyr 0 Goins shows the number of coins deposited in the left coin mechanism. © Plyr 1 Coins shows the number of coins deposited in the right coin mechanism.

Aux Count 0 shows the number of times players continued their characters at level 10 or earlier. © Aux Count 1 shows the number of times players continued their characters at level 11 or higher. 0 Plyr Mins shows the minutes of idle time. © 1 Plyr Mins shows the minutes played as a 1-player game. 2 Plyr Mins shows the minutes played as a 2-player game. © L Plyr Mins shows the total number of minutes that the left player has played. © R Plyr Mins shows the total number of minutes that the right player has played. Total Games shows the total number of games played. One “‘game”’ is the time between the first player starting and both players dying, regardless of time, number of coins inserted, or how many have played Xybots. © Error Count shows the number of EEROM errors that were detected. Replace the EEROM at location 20C/D on the Game PCB if the errors detected exceed approximately 75 per week. © Total Coins shows the total number of coins deposited in all the coin mechanisms. Avg Time/Coin shows the average game time per coin, in seconds, for all players. Press the left Fire button to obtain the next screen.

Page 17

Xybots

Histograms

The Histogram screen is shown in Figure 2-7. For both players, the screen shows the lengths of the games from 0 to 300 or more seconds. The Histogram also provides corresponding bar graphs. The game times information is accumulated either from the first time the game was turned on or from the last time the game times were reset. To reset the Histograms, press the left Start button. Press the left Fire button to obtain the next screen.

Playfield Test

The Playfield Test is shown in Figure 2-8. Under the title PLAYFIELD TEST are five rows of pictures. The first row has sixteen colors: black, red, green, blue, white, . . .,and orange. The second row has 16 different symbols in various colors. Some of the symbols include: a yellow right angle with a dot inside of it, blue-and-orange arrows pointing in different directions, an orange diamond, etc.

¥ button his tagr de

Use joyetiok t to step throw iieta piotere: Bress Left Piavar FIRE a 25. ext to advance. See

Figure 2-8 Playfield Test Self-Test

The third row has 16 colored blocks of different sizes: two white blocks, seven yellow, and seven red. The fourth row has one line of white dots slanting down to the right, followed by one line of yellow dots. The fifth row has one line of orange dots slanting down to the right and one line of red dots.

At the bottom of the screen are two large pictures of the view seen by the players. By moving the left-player joystick up or down, the pictures will change. By advancing through 18 sets of pictures, you can visually check that the data in playfield EPROMs located at 8L, 11L, and 12L are OK. Not all pictures in the playfield EPROMs are tested. If the attract mode pictures of the title screen, the high score screen, the story line screen, or the pictures surrounding the players score are incorrect, then this could indicate a failure in the playfield circuitry. Press the left Fire button to obtain the next screen.

Motion Object Test The Motion Object Test appears is shown in Figure 2-9. The Motion Object Test indicates the condition of the motion-object buffer circuit. There are fifty-six objects, eight pixels wide, placed in two rows in the center of the screen. The following information is provided at the bottom Of the screen: © OBJECT indicates the number of the motion object selected. © PICTURE indicates the stamp number in ROM. © HORIZONTAL indicates the horizontal position of the object.

  • VERTICAL indicates the vertical position of the object. © SIZE indicates the number of stamps high. © COLOR PALETTE indicates the palette number for colors.

Motion Gbject Test Re

“4 s Fs

J ag

a al

Figure 2-9 Motion Object Test

Page 18

© PRIORITY indicates which playfield palettes have Priority over the motion object. Perform the test procedure as described in Table 2-4. Press the left Fire button to obtain the next screen.

Alphanumerics Test The Alphanumerics Test is shown in Figure 2-10. This test indicates the condition of the alphanumerics circuit. Check that there are no errors on the screen. If there are errors, check the EPROM at 5C or its circuitry. Press the left Fire button to obtain the next screen.

Color Test The Color Test is shown in Figure 2-11. This Test indicates the condition of the display color circuits.

Table 2-4 Motion Object Test Description

Control/Movement Function

Left Start Displays a different set of pictures. (See PICTURE.) Press this button and inspect all pictures from 0 to 37FE If there are errors, inspect: EPROM Location

Pictute on Game PCB

0-7FF 2E 800-FFF 2E/F 1000-17FF 2F 1800-1FFF 2F 2000-27FF 2y/K 2800-2FFF 2K 3000-37FF =. 2L Left Joystick Changes the horizontal and vertical position of the selected object. (See HORIZONTAL and VERTICAL.) Left Joystick/Turn Decreases the selected object num-

Left ber. (See OBJECT.)

Left Joystick/Turn Increases the selected object num- Right ber. (See OBJECT.) Right Start Toggles the horizontal flip bit of the selected object. (See PICTURE.) Right Fire Increases the priority of the selected object. (See PRIORITY.) Right Joystick/Left Decreases the palette of the selected object. (See COLOR PALETTE.) Increases the palette of the selected object. (See COLOR PALETTE.) Increases the size of the selected object. (See SIZE.) Decreases the size of the selected object. (See SIZE.) Right Joystick/Right

Right Joystick/Up

Right Joystick/Down

Right Joystick/Turn Decreases the picture of the selected

Left object. (See PICTURE.)

Right Joystick/Turn Increases the picture of the selected

Right Object, (See PICTURE.)

2.6 Xybots

Figure 2-11 Color Test

The screen should show 16 vertical grey-scale bars and three blocks of red, green, and blue, each containing 16 vertical bars. The brightest bars should be on the left and darkest (black) on the right with a grey frame around the screen. This frame will help to identify the darkest color band. If the display characteristics are not correct, refer to the display manual for the color-gun adjustment procedure or to determine the possible cause of failure, To adjust the brightness, find the darkest column (not black) with the red, green, and blue colors. This column should be just barely visible. Press the left Fire button to obtain the next screen.

Color Purity Test

The Color Purity Test consists of five color displays that indicate the condition of the display color-purity circuits. The first display to appear should be a red screen with the word RED displayed at the bottom of the screen as shown in Figure 2-12.

Page 19

Xybors

Figure 2-12 Color Purity Test

Figure 2-13, Convergence Test

Press the left Start button, and the next display to appear should be green with the word GREEN displayed at the bottom of the screen. Press the Jeft Start button to obtain a blue, white, and finally a grey screen. After the grey screen, the display will repeat the red, green, blue, white, and grey sequence again. If the display characteristics are not correct, refer to the display manual for the color-purity adjustment procedure or the possible cause of failure. Press the left Fire button to obtain the next screen.

Convergence Test The Convergence Test is shown in Figure 2-13. This test indicates the condition of the display size, centering, linearity, and convergence. The grid pattern should be white. Press the left Start button and the grid pattern should turn. violet. Pressing the left Start button again should cause the grid pattern to turn green. Check the grid pattern for Self-Test

the following characteristics (the violet and white patterns are used to adjust the display convergence): © The four corners of the frame around the grid pattern should touch all four corners of the screen. Grid lines should show no pincushioning or barreling, and the lines should be straight within 3.0 mm. Violet and white pattern convergence should be within 2.0 mm. If the display characteristics are not within these limits, refer to the display manual for the linearity and convergence adjustment procedures or to determine the possible cause of failure. Press the left Fire button to obtain the next screen.

Sound Test The Sound Test is shown in Figure 2-14. This test indicates the condition of the coin mechanisms and the music, speech, and sound-effects circuits. The sound microprocessor is reset at the beginning of this test. The game may take up to three seconds to produce the first sound. If the sound-microprocessor reset fails, the message SOUND PROCESSOR NOT RESPONDING should blink near the top of the screen, or SOUND CPU RAM 1 ERROR will be displayed near the top of the screen. If the sound microprocessor is good, check the coin mechanisms and the sound microprocessor circuits by observing the following messages: © CURRENT COIN VALUE consists of four zeros, For the left and right coin mechanisms, the third and fourth 0 respectively, should change to a 1 as the coin switch is held down, and should change back to 0 when the coin switch is released. NUMBER OF SOUNDS indicates of the number of sounds used in the Xybots game.

Page 20

Self-Test

good, the word GOOD should appear. If the sound microprocessor or associated circuitry is faulty, a number will appear (to indicate sound status) in addition to an error message located at the top of the screen. Refer to Table 2-5 for the error messages and faulty sound RAM and ROM locations on the Audio PCB. © SOUND # indicates the sound selected by moving the left joystick up (increments the sound number) or down (decrements the sound number). To hear the sound, press the left Start button one or more times. Moving the left joystick right or left silences the sound. You can select the following integrated circuit (chip) tests during the Sound Test: © Sound 4 (Music Chip Test) consists of eight tones in a major scale that alternate between sound channels (16 tones in all), Press the left Fire button to return to the Switch Test. Xybors.

Table 2-5 Faulty Sound RAM and ROM Locations

Location on Stand-Alone Audio Error Message PCB/Cause

Music Chip Time Out. 2F Sound CPU Interrupt —_2F, 5K, Transistor Q8 Error Sound CPU RAM 1 2H Error If displayed when entering test, then sound processor cannot run further, Press Fire button to obtain next test. Sound CPU ROM 1 2K Error Communications 1M Error #1 ‘Will count number of errors caused by either the Audio PCB or Game PCB. Communications A probable disconnection of Audio Error #2 PCB from Game PCB, or the chip at 1M is not inserted into its socket. Sound Processor Not — A major problem with the Audio Responding PCB.

If-you cannot enter the self-test, the cause may be a barness disconnection between the Audio and Game PCBs.

Page 21

iblepre-

that

ponents that

ecommend we rec le, tive and corrective mainte-

. To assure maximum troul prevent

of this game that are in the maintenance pro a / a Chapter 5, Illustrate ive maintenance. correcti ‘ vided to) arts trated, part ¢ free operation ventive maint

th \ Nene on 4 ae : 4 i ras cy ne ear y RoE erees we Way cin eens een X02 aan sonaec rua Lowclocnne mvon aes rec amelie ATS

Page 22

Maintenance Xybots

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening hardware. How often preventive maintenance is performed depends upon the game environment and frequency of play. However, for those components listed in Table 3-1 Preventive-Maintenance Intervals, we recommend that preventive maintenance be performed at the intervals specified.

Preventive-Maintenance Intervals

The preventive-maintenance intervals specified in Table 3-1 are the recommended minimum requirements for the components listed.

& WARNING A To avoid possible electrical shock, turn off the game before performing any maintenance procedures.

Removing the Control Panel

Perform the following procedure to remove/replace the control panel. (See Figure 3-1.)

  • Use the tamperproof hex-key wrench (included in the instruction manual bag) to remove the four tamperproof screws and washers holding the control panel to the cabinet.
NOTE Ahole is provided on the cabinet shelf inside the upper coin door to conveniently store the hex-key wrench when not being used. This hole is located to. the left of the coin slots.
  • Grasp the joystick and gently lift until the bottom edge of the control panel clears the cabinet.
  • Disconnect the two control panel harness connectors and remove the control panel from the cabinet.

Table 3-1 Recommended Preventive- Maintenance Intervals

Joystick Inspect weekly, lubricate, and tighten hardware at least every three months. Coin Mechanism Inspect whenever you collect coins. Clean at least every three months.

3-2 4, Replace the control panel in the reverse order of removal.

Cleaning the Push-Button Leaf

Switches

Perform the following procedure to clean the leaf-switch contacts and tighten the securing hardware. (See Figure 3-1.) 1, Remove the contro! panel as previously described in this chapter. 2, Use electrical contact cleaner to clean the contacts. Do not burnish them. When the push button is pressed, the wiping action of the cross-bar contacts provides a self-cleaning feature. Then use the Self-Test to verify proper switch contact.

  • Use a '%.-inch open-end wrench to tighten the stamped nut holding the push-button leaf switches to the control panel.
  • Repiace the control panel in the cabinet in the reverse order of removal.

Joystick

Preventive maintenance on the 8-position, snap-action joystick consists of: © Inspecting the pivot and actuator balls for excessive wear or dirt. © Lubricating the pivot ball. © Replacing or tightening the securing hardware if necessary.

Lubricating the Joystick Perform the following procedure to lubricate and tighten the joystick. (See Figure 3-1.)

  • Remove the control panel as previously described in this chapter.
  • Use a inch wrench to remove the four nuts holding the joystick to the control panel.
  • Apply a small amount of lithium grease (Atari part no. 178027-001) to the lubrication points shown in Figure 3-2,
  • Use a Phillips screwdriver to tighten the screws holding the positioning plate to the lower housing.
  • Apply a light film of light oil (Atari part no. 107013- 001) to the lubrication points shown in Figure 3-2.
  • Replace the joystick in the control panel in the reverse order of removal.
Page 23

‘Xybots

Cross-Bar Leaf Switch with Button Holder Maintenance

1”-Long Carriage Bolt and Hex Lock Nut

Control Pane! Deca!

Figure 3-1 Leaf Switch and Joystick Removal

Cleaning the Coin Mechanism

Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Interior

Components

Perform the following procedure to clean the components inside the cabinet.

& WARNING A ‘Turn off the game power, but do not unplug the power cord before cleaning inside the cabinet. The Power cord provides a ground path for stray static voltages that can be present on the cleaning tools.

1, Unlock and open the rear access panel and display service panel.

  • Discharge the high-voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. c, Wait two minutes and repeat part b.
CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush,
  • Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of
Page 24

Maintenance

Screw Torque Specifications

‘Seating Torque Ref. No. Screw Size in Inch-Lbs.

(0)816 x22 long541
®@4-40 x% long1242
@10-24 x 1¥2 long174#1
@10-24 x % long2042
©4-40 x% long441
©4-20 x¥% long2405

N } a ~ Lower Housing \

Snap Switch | I a q 5

Actuator \Cushion Ring |

8-Position Plate

@ #8-16x2.5" Long Screw —" hj (4 places)

#10-24 Screw and Nut @)

tp (2 places)

Bracket = #4-40 Screw and Nut XN tink (4 places) N ¥#10-24 Screw @ and Nut nap-Action Switch Clip Ring : @ places) © a Xybots

Knob Handle

Disc

Hollow Shaft

Spring

Close-Wound End

Plunger

Upper Housing

Pivot Ball aul Actuator Ball NN

Figure 3-2 Joystick Disassembly and Lubrication

3-4

Page 25

Xybots

the cabinet. Be sure to clean the electrical components Maintenance

thoroughly (power supplies, PCB assemblies, display, etc.).

Corrective Maintenance

Corrective maintenance consists of removal, disassembly, reassembly, and replacement of game components. The following procedures are provided for components that may require corrective maintenance.

Removing the Joystick

Perform the following procedure to remove/replace the joystick. (See Figure 3-1.) 1. Remove the control panel as described under Preventive Maintenance, . Disconnect the fast-on connectors from the six snapaction switches. . Use a %inch hex driver to remove the four nuts holding the joystick to the control panel.

  • Carefully lift the joystick out of the control panel. . Replace the joystick in the reverse order of removal. Reconnect the fast-on connectors to the snap-action switch terminals as shown in the Detailed Control Panel Game Wiring Diagram in the Schematic Package (SP-313).

Disassembling the Joystick

Perform the following procedure to disassemble the joystick assembly. (See Figure 3-2.) 1. Use a small screwdriver (or appropriate tool) to remove the ring cip from the bottom of the shaft. . Remove the extension spring from the link pin. Remove the link. . Use a small screwdriver (or approptiate tool) to remove the second ring clip from the bottom of the shaft. 4, Remove the knob handle and disc. . Use a % Allen wrench and %-inch wrench (or hexdriver) to remove the two clamps from the switch bracket. . Use a Phillips screwdriver to remove the four screws holding the positioner plate to the lower housing. . Remove the actuator. . Remove the lower housing with the four snap-action switches from the upper housing.

NOTE The following steps describe the procedure for disassembling the upper housing assembly. 11.

12. . Remove the actuator ball from the shaft.

10. Use a, Allen wrench to remove the two cap screws holding the pivot-ball halves to the shaft. Slide the shaft out of the housing and remove the plunger and spring from the shaft. Reassemble the joystick as described in the following procedure.

Reassembling the Joystick

Perform the following procedure to reassemble the joystick. (See Figure 3-2.)

NOTE If the upper housing assembly was not previously disassembled, proceed to step 7.

1, Slide the spring onto the hollow shaft.

10. . With the bell-shaped end toward the end of the shaft, slide the plunger onto the hollow shaft and over the spring. . Slide the end of the hollow shaft through the top of the upper housing. . Attach the pivot-ball halves to the hollow shaft with the two 4-40 x %-inch cap screws. . Slide the actuator ball onto the end of the hollow shaft. . Tilt the hollow shaft to one side, and apply a small amount of lithium-base lubricant (Atari part no. 178027-001) to the contact area between the plunger and the upper housing, . Place the lower housing over the hollow shaft and align the four screw holes in the upper housing with those in the lower housing. . Apply a thin film of light oil lubricant (Atari part no. 107013-001) to the inside and thrust surfaces of the bronze bearings in the hollow shaft. . With the beveled hole toward the lower housing, place the actuator over the hollow shaft. Be sure that the cushion ring is in place. Gently place the positioner plate over the actuator and adjust the plate until the four screw holes are aligned with those in the lower housing.

Page 26

Maintenance

11.

12.

13. 14,

15. 16.

17.

18,

19. Insert the four 2%-inch screws into the four screw holes in the positioner plate. Use a Phillips screwdriver to tighten the four screws until the head of each screw touches the plastic surface. Check that the ball handle returns freely to the centered position. Next, attach the two clamps on the shaft. Slide the disc onto the hollow shaft. Jnsert the knob handle through the hollow shaft. Place one ring clip on the shaft directly below the bronze bearing. Attach the link with the pin below the ring clip. Be sure that the pin is aligned so that the pin protrudes through the center of the opening in the switch bracket. Place the second ring clip at the end of the shaft. Attach the extension spring of the bracket onto the clamp pin.

Removing the Video Display

Perform the following procedure to remove/replace the video display. (See Figure 3-3.) I. Turn the game power off and wait two minutes, Unplug the power cord. . Use a inch hex driver to remove the eight screws holding the display frame to the cabinet. Remove the frame. . Remove the video display shield. . Carefully remove the bezel from the protective foam tape. . Use a Kinch hex driver to remove the four screws holding the display service panel. Remove the panel.

A WARNING A

High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display unul you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize Xradiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped, Shattered giass may cause injury within a 6foot radius. Use care when handling the display.

3-6 . Be sure that the game power is turned off before discharging the high-voltage from the cathode-ray tube aa Xybots

(CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows. a. Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. b, Momentarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap.

c. Wait two minutes and repeat part b. . From the rear of the cabinet, disconnect the display harness connectors from the display.

To avoid dropping the video display, use extreme care when removing the display from the cabinet. We recommend that no one weighing less than 150 pounds should attempt to remove the display. In addition, we recommend that you wear gloves to protect your hands from the sheet-metal edges.

10.

nM, . Use a inch nut driver to loosen the four screws holding the display to the two mounting brackets. . Use aij<inch nut driver to remove the four nuts and. washers holding the mounting brackets to the cabinet studs.

Carefully lift the display out through the front of the cabinet.

Replace the video display as described in the following procedure,

NOTE ‘Whenever the cathode-ray tube and yoke are replaced as a single unit, readjust the brightness, size, and centering as described in the display manual. Check the purity and convergence also according to the display manual instructions, but adjust both only if required.

Replacing the Video Display

Perform the following procedure to replace the video display in the cabinet. (See Figure 3-3.) 1.

3. Carefully lift the video display through the front of the cabinet.

Position the display so that the four holes in the two mounting brackets align with the four studs in the cabinet.

Tighten the four mounting nuts and washers holding the mounting brackets to the cabinet studs.

Page 27

Xybots

Video Display Bezel

Video Display Shield

Grille Mounting Screw (4 places) Speaker Mounting Screw Maintenance

Fluorescent Light (4 places)

Screw

Speaker Area

Figure 3-3 Control Panel, Video Display, and Speaker Removal

  • Use a -inch nut driver to tighten the four screws securing the display to the mounting brackets. Be sure that the display is centered horizontally.
  • Connect the display harnesses to the display.
  • Replace the bezel, display shield, and display frame.

Removing the Game PCB

Perform the following procedure to remove/replace the Game PCB.

  • Turn the game power off.
  • Unlock and remove the rear access panel from the cabinet.
  • Disconnect the harness connectors from the Game PCB. 4, Use a Phillips screwdriver to remove the two screws and washers holding the Game PCB to the cabinet.
  • Grasp the edge of the Game PCB and gently lift it out of the slotted guide.
  • Replace the Game PCB in the reverse order of removal.

Removing the Fluorescent Light

Perform the following procedure to remove/replace the fluorescent light. (See Figure 3-3.)

  • Turn the game power off.
  • Usea \-inch hex driver to remove the six screws holding the light-box frame to the top of the cabinet. Remove the frame. . Remove the light-box plastic shield. . Remove the fluorescent light from the light fixture.
  • To remove the entire light fixture, use a %-inch hex driver to remove the four screws holding the display service panel at the rear of the cabinet. Remove the door. Bo
  • Disconnect the light harness connector in the rear of the cabinet.
  • Use a Phillips screwdriver to remove the two screws holding the light fixture. Remove the light fixture.
  • Replace the fluorescent light and/or light fixture in the reverse order of removal.

3-7

Page 28

Maintenance

Removing the Speakers

Perform the following procedure to remove/replace the speakers. (See Figure 3-3.)

  • Turn the game power off.
  • Use a inch hex driver to remove the four screws holding the speaker grille to the cabinet. Remove the grille.
  • Disconnect the speaker harness assembly.
CAUTION Do not touch the speaker cones when handling the speakers. The cone material is fragile and can be easily damaged. Xybots

4, Use a Phillips screwdriver to remove the four screws holding the speaker to the cabinet. Do not let the speaker fall.

  • Lower the speaker just far enough to disconnect the two speaker wires. Be sure that you hook up the wires correctly. Otherwise, the game will produce less than. the desired volume because the speakers will be out of phase. The signal wire on each speaker should be attached to the speaker tab marked with color, a + sign, or a round dot. (The signal wires are shown on the game wiring diagram; refer to the Schematic Package included with the game.)
  • Replace the speaker in the reverse order of removal.
Page 29

tet Ded EL Gee, tip danes gene ME. Pus ounire a Srete te yen i 3 ae he ue

Penta Hae sea es He

cian. cedures be performed by a qualified service techni-

NOTE

We recommend that troubleshooting and repair proic!

E s o a g g mJ B z a g = z & é Fi g &. discusses

ter. However, if problems persist, contact your local distributor or your Atari Games Corporation Customer ‘kly by following the information in this chaptroubleshooting

Bem one

Page 30

‘Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the schematic package supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information.

Assembly and Component Locations The parts lists in Chapter 5 of this manual illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components shown on the corresponding schematic diagram(s).

Diagrams

The schematic package supplement for this manual contains schematic diagrams with component locations, active component type numbers, and electrical values.

Troubleshooting Techniques

A WARNING A To avoid electrical shock, turn off the game power before attempting to troubleshoot this game. Xybots

Visual Check

Visually check for obvious problems in the portion of the game where the trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, and damaged PCBs or components.

Check Individual Components

Check soldered-in passive components (¢.g., resistors, capacitors, diodes) by disconnecting one end to isolate the measurement from the effects of the surrounding circuitry. Often, direct substitution is the most practical way to determine if a component is faulty. However, eliminate the possibility of some other circuit problem that could damage the substitute component.

Repair the Assembly

CAUTION Soldered-in transistors and integrated circuits are difficult to remove without damaging the printed-circuit board or component. Refer to the information in this chapter pertaining to soldering and replacing integrated circuits and transistors.

The following troubleshooting steps are arranged in a sequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the problem to an assembly or major circuit, and then to a defective component.

Check Fuses

Check for open fuses. Refer to the power supply parts list in Chapter 5 and to the display manual for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.

Check Power-Supply Voltages

Improper operation of all circuits usually indicates a power supply problem. Be sure that the proper line voltage is available to the power supply. Refer to the label on the power supply for its voltage rating.

Localize Trouble

Determine the trouble symptom. Use the wiring diagrams in the schematic package supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2 of this manual. Repair or replace the defective part. Refer to Chapter 3 and information in this chapter for special removal and replacement procedures. Check for proper operation of the repaired circuit.

Soldering Techniques

Observe the following recommendations when remoying or replacing components soldered to a PCB. Poor soldering practices can damage a PCB or heat-sensitive electrical components.

Choosing the proper soldering iron is essential before attempting to remove or replace soldered-in components. Excessive heat is a common cause of damage to a component or PCB. However, transient voltages from solder guns or improperly grounded soldering irons can also damage certain voltage-sensitive semiconductor devices. Refer to Troubleshooting Static-Sensitive Devices for more specific information.

A15- to 27-watt pencil-tip soldering iron is recommended to avoid separating the etched circuit wiring from the board material and to avoid damaging active components, A temperature-controlled soldering station rated at 700°F with a fine cone or a very fine chisel tip can also be used.

Page 31

Xybois

CAUTION Solder guns are not recommended for removing or replacing soldered-in components on a printed-circuit board. Solder guns can overheat a device, and their large transient voltage can damage a voltage-sensitive device.

The following additional equipment is recommended for removing and replacing soldered-in components:

  • Solder Sucker—Hand-operated vacuum tool used to remove liquified solder from the PCB. We recommend the top-of-the-line Soldapullt® brand. Solder Wick—Resin-soaked copper braid used for removing excess solder from the lead connections on the PCB. See Removing Integrated Circuits for precautions relating to the use of a solder wick on a multi- Jayer PCB with plated-through holes. ¢ Flux Remover—Non-corrosive chemical used to clean foreign material from the PCB before soldering and to remove any flux residue where components have been replaced. Also used to clean any foreign material from the PCB during preventive maintenance. Isopropyl alcohol is recommended. ¢ Acid Brush—Small stiff-bristled paint or toothbrush used with flux remover to clean flux and other foreign material from the PCB.

Removing Integrated Circuits The easiest and safest method for removing soldered-in integrated circuits (IC) from a PCB is to cut off each pin as close to the IC case as possible with a tip dyke (diagonal cutter) as shown in Figure 4-1. Use the proper soldering iron as previously described under Soldering Techniques. Then, to avoid excessive heat buildup in one area of the PCB, apply heat directly to each pin in a random order. Remove the loosened pin with the tip of the soldering iron or a needle-nose pliers as shown. in Figure 4-2. Allow a moment for the PCB to cool before proceeding to the next pin. Apply just enough heat to remove any stubborn pins.

Diagonal Cutter

Figure 4-1 Removing IC (Cut-Pin Method) ‘Troubleshooting

Needle-Nose Pliers

Soldering Iron

Figure 4-2 Removing IC Pins

For a multi-layer PCB with plated-through holes, use a solder sucker to remove the remaining solder from inside each hole as shown in Figure 4-3. If possible, suck the solder from the opposite side of the PCB from where the heat is applied. Use a solder wick to remove excess solder from around the lead connection pads on the top and/or bottom surface of the PCB as shown in Figure 4-4.

CAUTION Do notuse a solder wick to remove solder from inside plated-through holes. The heat required for the solder wick to remove the solder from inside the hole could damage the PCB.

Use an integrated-circuit (IC) pulling tool to remove socketed ICs. Do not pry up on one end of the ICs, because the pins could be bent or broken.

Troubleshooting Static-

Sensitive Devices

Certain precautions must be taken when working with static-sensitive devices, e.g., microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge buildup in a person’s body or leakage from an improperly grounded soldering iron can cause static-sensitive device failure. Before handling a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded. A bare wire wrapped around your wrist and attached to an earth ground is effective when working extensively with static-sensitive de-

Page 32

‘Troubleshooting

Solder Sucker

Preferred Method Soldering iron Solder Sucker Xybots

Soldering iron

Alternate Method

Figure 4-3 Removing Solder from Plated-Through Holes

Soldering Iron Solder Wick

Figure 4-4 Removing Solder from Lead Connection Pads vices. When soldering a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. (Refer to Soldering Techniques for a discussion of recommended soldering irons and procedures.) A static-sensitive device can appear defective due to leakage on a PCB. Observe the precautions for grounding static voltages described in the preceding paragraph and clean both sides of the PCB with flux remover or an eraser before replacing what can be a good static-sensitive device. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Static-sensitive devices can be packaged in conductive foam or have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it toa PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Page 33

PERN FRANCE SL DOM gt NR YS NEARS Sa ETA mms Mage

ave i g & g s 8s a

e.

re cor phanum ha ‘oni€ ‘ual nent. Each comport erically by referei Ipor

lumber. In these p

up to the hyphen,

ly. We hope the results will be profit from your game.

f first. Following these a :

Customer Service numbers are number of this manual, give Ag Se This will help us fill your’

a 1 ber of your 7

rapidly and corss. downtime and.....

y ia

Page 34

Illustrated Parts Lists Xybots

044905-01 99-11006 Attract Decal Retainer Clip 171086-001 044899-01 178056-002 Lamp Fiture Ventilation Grille lied dabei 044901-01 170003-001 _ 044995-01 044960-01 Display Mointing Bracket yet Fluorescent Lamp _ Display Service Panel 1 Display Shield VA" x Jr" Foam Tape peao08-01 Display Frame 139021-001 044958-01 Side Pacis Sharp Display Light-Box Frame Decal

044957-01 brie Light-Box Shield Display Mointing Bracket a

A044877-01 Speaker Harness Assy 148007-003!

044902-01 Video Display Bezel S 044956-01 | a Speaker Grille o

Control Panel Assy See Figure 4-2

8-Position Joystick Assy See Figure 4-3 & S

Front Panel Decal

Coin Door Assy i See Figure 4-5

044949-01 038091-01 Rear Access Panel Molded Coin Box ) eieacditheias Stand-Alone Audio PCB Assy ui eaves See Figure 4-7

171078-002 Coin Counter

Figure 5-1 Cabinet-Mounted Assemblies A044895-01 B

5-2

Page 35

Xybots Iftustrated Parts Lists

Items Not Shown:

NOTE For more information on installing harnesses in the cabinet, see the Xybots Harness Installation Diagram in the Xybots Schematic 178093-001 Package Supplement (SP-313). Fan Blade Guard 178126-002 Tamperproof ¥,. Hex-Key Wrench

A044875-01 AC Power Harness Assy A044876-01 Display Harness Assy A044878-01 Com/Aud Harness Assy A044879-01 Cabinet and Coin Harness Assy A044883-01 Ground Strap Assy 044902-02 Water Deflector

Xybots Game PCB Assy See Figure 4-6 178129-001 Wire Routing Clip

A044874-01 Power Harness Assy

044911-01 Edge Trim

A043055-01 A044900-01 On/Off Switch Assy with Harness Cabinet Assy

Power Supply Assy See Figure 4-4

78-3201 Adjustable Glide

Figure 5-1 Cabinet-Mounted Assemblies, Continued

Page 36

Illustrated Parts Lists Xybots

Cabinet-Mounted Assemblies Parts List

Part No. Description

A043055-01 12-Inch-Long On/Off Switch Assembly with Harness A044874-01 Power Harness Assembly A044875-01 AC Power Harness Assembly A044876-01 Display Harness Assembly A044877-01 Speaker Harness Assembly A044878-01 Communications/Audio (Com/Aud) Harness Assembly A044879-01 Cabinet and Coin Harness Assembly A044883-01 Ground Strap Assembly A044900-01 Cabinet Assembly 78-3201 Adjustable Glide 78-6900401 %4-Inch-Wide x ¥-Inch-Thick Foam Tape (150 inches required; used on inside lip of display frame and light-box frame to protect plastic shields) 99-11006 Fluorescent Lamp Retainer Clip 038091-01 Molded Coin Box 044899-01 Ventilation Grille 044901-01 Display Mounting Bracket 044901-02 Display Mounting Bracket 044902-01 Video Display Bezel 044902-02 Water Deflector 044905-01 Attract Decal 044906-01 Front Panel Decal

044908-01 Side Panel Decal 044911-01 Edge Trim 044935-01 Display Service Panel 044949-01 Rear Access Panel 044956-01 Speaker Grille 044957-01 Light-Box Plastic Shield 044958-01 Light-Box Frame 044959-01 Display Frame 044960-01 Display Shield 139021-001 Sharp Model XM-2001N 19-Inch Color Raster Video Display 148007-003 4%_-Inch Round, 80, 10 W, Unshielded Speaker 170003-001 18-Inch-Long 50 W Fluorescent Lamp 171078-002 12 VDC Non-Resettable Terminated Coin Counter 171086-001 18-Inch-Long 118 V 60 Hz Fluorescent Lamp Fixture 178056-002 ¥-Inch-Wide x ¥-Inch-Thick Foam Tape (4 inches required; used on corners on underside of display bezel) 178093-001 Fan Blade Guard 178126-002 Tamperproof %, Hex-Key Wrench 178129-001 Wire Routing Clip The following items are technical information supplements for this game: TM-304 Sharp Model XM-2001N Video Display Service Manual ™313 Xybots Operators Manual SP-313 Xybots Schematic Package ST-313 Xybots Self-Test Label

5-4

Page 37

Xybots

item Not Shown: 78-6900402 Foam Tape Illustrated Parts Lists

75-5116B 1-Inch-Long Carriage Bolt

160013-002 044904-01 Cross-Bar Leaf Switch with Control Panei Decal Button Holder

044955-01 Control Panel

Leaf Switch with Bution Holder 75-9910NO A044880-01 samped Nut Harness Assy &-Position Joystick Assy See Figure 4-3

Figure 5-2 Control Panel Assembly A044898-01 A

Control Panel Assembly Parts List

Part No. Description

A044405-01 A044880-01 75-5116B 75-9910NO

78-6900402 044904-01 044955-01 160013-001

160013-002 177010-240 178030-003, 8-Position Joystick Assembly Control Harness Assembly #10-24 x 1.00-Inch-Long Black Carriage Bolt #11-%Inch Stamped Nut

¥4-Inch Wide x 4Inch Thick Foam Tape (50 inches required) Control Panel Decal Control Panel Leaf Switch with Button Holder

Cross-Bar Leaf Switch with Button Holder #10-24 Polymer Lock, Hex Lock Nut Black Nylon Button Assembly

5-5

Page 38

Illustrated Parts Lists 7 Xybots 044406-0° Molded Knob Handle, or 044962-01 Machined Knob Handle

NOTE After reassembling this joystick control, be sure that all necessary screws are properly tightened. See Figure 3-2 in this manual for the Screw Torque Specifications table.

044407-01 Hollow Shaft

041287-01 ! > N Lower Housing 043696-01 Compression Spring

160041-001 ‘Snap-Action Switch, or 160038-001 Gold Snap-Action Switch, or 039712-01 Plunger

044390-01 + Cushion Ring

039722-01 Upper Housing

03971703 | Positioner Plate

176010-140 >| 2¥a"" Screw | Clamp

044411-02 Clamp with Pin cK %" Screw PS SN 72-81248 7 12" Screw Lainey 044410-01 ' Hal-Pivot Ball

‘Switch Bracket . 044412-01 72-84108 3 Link y" Screw 72-8112B 7 177010-232 34" Screw . altos #4-40 Nyloc Nut 177010-240 N Split Actuator Ball sveozeoi #10-24 Nyloc Nut NY ee oT 04498401 +78012.002 tension Spring ogiied Snap- Ring Clip Action Switch

Figure 5-3 8-Position Joystick Assembly A044405-01 A

5-6

Page 39

Xybots Illustrated Parts Lists

8-Position Joystick Assembly Parts List

Part No. Description

72-8112B #10-24 x %4-Inch Socket-Head Cap Screw 72-8124B #10-24 x 1%-Inch Black Socket-Head Cap Screw 72-8406 #4-40 x %-Inch Socket-Head Cap Screw 72-8410B #4-40 x },Inch Socket-Head Cap Screw

039712-01 Plunger 039713-01 Disc 039714-01 Actuator 039717-03 8-Position Positioner Plate

039722-01 Upper Housing 041287-01 Lower Housing 043696-01 Compression Spring 044406-01 Molded Knob Handle (Acceptable substitute is part no. 044962-01, Machined Knob Handle)

044407-01 Hollow Shaft 044408-01 Half-Pivot Ball 044408-02 Half-Pivot Ball with Flush Pin 044409-01 Split Actuator Ball

044410-01 Switch Bracket 044411-01 Clamp 044411-02 Clamp with Pin 044412-01 Link

044390-01 Cushion Ring 044984-01 Modified Snap-Action Switch 107013-001 Light Oil Lubricant 160044-001 SPDT Snap-Action Switch with Gold Contacts

176010-140 #8-16 x 2% -Inch-Long Cross-Recessed Pan-Head Screw 176030-110 #4-20 x .62-Inch-Long Self-Tapping Hex Washer-Head Screw 177010-232 #4-40 Nyloc Nut 177010-240 #10-24 Nyloc Nut

178012-002 Ring Clip for %-Inch Shaft 178026-011 Extension Spring 178027-001 Lithium Lubricant

5-7

Page 40

Illustrated Parts Lists Xybots

A WARNING A The switching power supply has high voltages on it when power is turned on. Therefore, be sure you do not touch this power supply unless you have turned offthe power to the game.

72-HA4606S ‘Screw 149003-xxx 5V 10 Amp Switching Power Supply Assy

A043367-xx 179231-002 Jumper Assy, Terminal Block 142042-001 Transformer

‘A043367-xx Jumper Assy

A043366-01 5V Harness Assy 72-HA4806S, Screw

043396-01 Power Supply Chassis Base

A042384-01 Line Filter Assy

46-2013002 Fuse

037640-01

Warning Label

179225-2205, or 79-3206 Fuse Block

034544-01 Fuse Block Cover

043622-01 Fuse Label 46-2012002 Fuse

Figure 5-4 Switching/Linear (SL) Power Supply Assembly A044872-03 A

Page 41

Xybots Illustrated Parts Lists

Switcbing/Linear (SL) Power Supply Assembly Parts List

Part No. Description

A042384-01 Line Filter Assembly A043367-01 Jumper Assembly 4043367-02 inch Black Jumper Assembly A043367-03 6-Inch White Jumper Assembly A043909-01 5 V Hamess Assembly 46-2012002 250 V Slow-Blow 2 A Fuse 46-2013002 250 V Slow-Blow 3 A Fuse 72-HA4606S #6-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw 72-HA4806S #8-32 x 3/8-Inch Cross-Recessed Pan-Head Thread-Forming Screw 034544-01 Fuse Block Cover 037640-01 Power Supply Warning Label 043396-01 Power Supply Chassis Base 043622-01 Power Supply Fuse Label 142047-001 Transformer 149003-003 Hitron 5 V 10 A Switching Power Supply Subassembly 179225-2205 5-Position Fuse Block (Acceptable substitute is part no. 79-3206) 179231-002 2-Position Terminal Block

Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List

DesignatorDescriptionPart No.

Capacitors

ClCapacitor, Metal Film, 0.047 uF, 250 V99-211036
c2Capacitor, Metal Film, 0.1 wE, 400 V99-211038
C3, C4Capacitor, Ceramic, 4700 uF, 400 V99-211049
C5, C6Capacitor, Electrolytic, 100 uF, 200 V99-211046
c7Capacitor, Metal Film, 0.1 4B, 400 V99-211038
c8Capacitor, Ceramic, 0.001 pF, 2 kV99-211042
coCapacitor, Ceramic, 0.01 wF, 1 kV, Z5U99-211041
C10Capacitor, Electrolytic, 220 ¢E 25 V99-211045
CllCapacitor, Metal Film, 0.22 nF, 100 V99-211037
C12Capacitor, Metal Film, 0.022 pF, 100 V99-211039
C13Capacitor, Metal Film, 0.22 uF, 100 V99-211037
cl4Capacitor, Ceramic, 1800 PF, 2 kV, Z5 V99-211040
C17Capacitor, Electrolytic, 470 uF, 25 V99-211044
C19Capacitor, Electrolytic, 2200 pF, 16V99-211048
C20Capacitor, Electrolytic, 1000 pF, 25 V99-211047
C21Capacitor, Ceramic, 470 PE, 1 kV, Z5P.99-211043
C22Capacitor, Electrolytic, 2200 pF, 16 V99-211048
C23Capacitor, Electrolytic, 1000 pF, 25 V99-211047
C24Capacitor, Electrolytic, 2200 uF, 16 V99-211048

Diodes

D1, D2Diode, Fast Recovery, RPG10K99-211010
D3Diode, Fast Recovery, RPG15B99-2110i1
D4Diode, Fast Recovery, RPGi0B99-211009
D5-D7Diode, Switching, 1N414899-211012
Page 42

Iilustrated Parts Lists

Hitron 5-Volt Power Supply Sub-Assembly Model HSA-122B(S) Parts List, Continued Xybots

DesignatorDescriptionPart No.

D9 Diode, Fast Recovery, 30DF1 -

D1, D12Diode, Schottky, S10SC4M300 i ee
D13-D16Diode, Rectifier, 1N400699-211008

Inductors

LlInductor, 15 mH99-211052
13Inductor, 7 pH (Acceptable substitute is part no. 99-211051)99-211050
L4Inductor, 2.2 hH99-211054
LbInductor, 1.5 mH99-211053

Resistors

R1, R2Resistor, Carbon Film, 180 k®, +5%, 1 W99-211034
R3Resistor, Wirewound, 1202, +5%,2W99-211019
R4Resistor, Wirewound, 0.472, +5%,2W99-211018
R5Resistor, Wirewound, 33 2, +5%, 2 W99-211017
RG, R7Resistor, Carbon Film, 5.60, +5%, 4 W99-211027
R8Resistor, Wirewound, 0.472, +5%,2W99-211018
ROResistor, Carbon Film, 100, +5%, 4 W99-211029
R10Resistor, Carbon Film, 1 kQ, +5%, 4 W99-211032
R11Resistor, Carbon Film, 470, +5%, 4 W99-211025
R12Resistor, Carbon Film, 5.62, +5%, 4 W.99-211027
Ri3Resistor, Carbon Film, 330 Q, +5%, 4 W99-211026
R14Resistor, Carbon Film, 2702, +5%, 2 W99-211023
R15Resistor, Carbon Film, 3302, +5%, 4% W99-211022
R16Resistor, Carbon Film, 8.2 2, +5%, 4 W99-211028
R17, R18Resistor, Carbon Film, 569, +5%, 4 W99-211031
R19Resistor, Carbon Film, 392, +5%, 4 W99-211030
R20Resistor, Carbon Film, 2 kQ, +5%, 4 W99-211035
R21Resistor, Carbon Film, 4700, +5%, 4 W99-211024
R22Resistor, 2.2 kO, +2%, 4 W99-211021
R23,Resistor, Metal Film, 2 k®, +2%, 4 W99-211033
R25Resistor, Carbon Film, 100, +5%, 4 W99-211029
R26Resistor, Wirewound, 509, +5%, 2 W99-211015
R27Resistor, Carbon Film, 47 2, +5%, 4 W99-211025
R31Resistor, Wirewound, 1502, +5%, 2 W99-211016

Transistors

Ql‘Transistor, NPN, 2SC1413A99-211002
Q3‘Transistor, NPN, PE8050B99-211003
Q3‘Transistor, PNP, PE8550B99-211004

Miscellaneous

FlFuse, 2 A, 250 V, SEMKO99-211058
ICRegulator, UA43 1AWC.99-211001
SCR1Thyristor, SCR99-211013
TiTransformer99-211055
TRIThermistor, 0.50, +5%,5 W99-211020
VRIPotentiometer, Trimming, 3 k®99-211014
ZD1Diode, Zener, 1N752A.99-211007

Fuse, 2 A, 250 V 99-211056

Fuse Holder, 6.35 mm 99-211060 Terminal Block, 8 Ckt 99-211057 Heat Sink 99-211059 Heat Sink, 1.5 mm. 99-211061

Page 43
Scan of page 43

This page is a drawing, shown as the original scan.

Page 44

Illustrated Parts Lists Xybots

99-10140 Panel Assembly 75-948S Locknut we QS . 99-10116 Ks ol, Lever 99-10152 Win Right Coin Inlet y s \ PA 99-10147 v wy Harness 171006-035 AY Coin Mechanism “gy

Locknut \\ 99-10096 ‘\ Fastener | 99-10151 L\

Left Coin Inlet N

70-11-47 L) Lamp N 99-1080 y Lamp Socket hi ¢ 99-10105 { Bar aN

99-10104 Bar Retainer

rs 99-10042 thru 99-10045 Coin Switch Assembly 99-10154 Bracket Assembly

99-10150 ‘Switch Cover

Coin Chute 65-441C Coin Switch

99-10075 thru 99-10078 ‘Switch Wires 99-10008 Retainer 7544125 Screw

Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 45

Xybots illustrated Parts Lists

99-10160 Coin Inlet Housing

72-HA1404C Screw ( aX 99.1016 99-1013 » & |) side Entry Button Assy Coin Door

7 a 99-4015 99-10148 Spring Lock Assembly

99-10141 Coin Return Cover

99-10117 Coin Return Door

I+——_ 99-10144 Channel Clip

99-15066 Screw

99-10149 Service Door

038091-01 Coin Box

99-10143 Frame

Ss coum

NOTE The acceptable substitute for this door (and the one used in games manufactured in Ireland) is the Coin Controls Ltd. Coin Door Assembly, part number 171034-001. You can obtain a free Coin Controls Ltd. supplement (part no. CO-305-01); it has illustrations and a parts list. Write to Atari Games Ireland Limited, Tipperary Town, Ireland. Telephone 0062-52155,

Figure 5-5 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

Page 46

Illustrated Parts Lists Xybots

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description

65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x %-Inch Truss-Head Screw 72-HA1404C #4-40 x Y4-Inch Pan-Head Screw 72-JA1405B #4-40 x 0.31-Inch Pan-Head Screw 75-14128 #4-40 x 34-Inch Pan-Head Screw 75-9948 #4-40 Locknut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgian 5 Fr and U.S. 25¢ 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute

99-10075Switch Wire(included in coin switch assembly 99-10043)
99-10076Switch Wire(included in coin switch assembly 99-10042)
99-10077Switch Wire(included in coin switch assembly 99-10044)
99-10078Switch Wire(included in coin switch assembly 99-10045)

99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-10115 Spring 99-10116 Plastic Coin Return Lever

99-10117 Steel Coin Return Door 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Die-Cast Coin Return Cover 99-10143 Coin Door Frame 99-10144 Channel Clip 99-10147 Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly 99-10160 1”-Wide Die-Cast Coin Inlet Housing

99-10161 25¢ Amber Side-Entry Button Assembly

99-15066 Screw for Clamp 171006-035 Metal Coin Mechanism for U.S. 25¢

5-14

Page 47

Xybots Illustrated Parts Lists

S

5-15

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

Xybots Illustrated Parts Lists

Xybots Game PCB Assembly Parts List

DesignatorDescriptionPart No.

Integrated Circuits

1AIntegrated Circuit, 74LS0037-74LS00
1BIntegrated Circuit, 74LS0237-74LS02
1cIntegrated Circuit, 7487437-74874
1DIntegrated Circuit, 741S17437-74LS174
2A, 2BIntegrated Circuit, 74LS0837-74L808
2CIntegrated Circuit, 74LS194A37-74LS194
2DIntegrated Circuit, 74LS13937-74LS139
2EIntegrated Circuit, EPROM, 27512-200136054-1105
2E/FIntegrated Circuit, EPROM, 27512-200136054-1106
2FIntegrated Circuit, EPROM, 27512-200136054-1107
2FI)Integrated Circuit, EPROM, 27512-200136054-1108
2y/KIntegrated Circuit, EPROM, 27512-200136054-1109
2KIntegrated Circuit, EPROM, 27512-200136054-1110
2LIntegrated Circuit, EPROM, 27512-200136054-1111
3AIntegrated Circuit, 74LS9037-74LS90
3BIntegrated Circuit, 74LS0037-74LS00
3CIntegrated Circuit, 741S194A.37-74LS194
3DIntegrated Circuit, 74L$283137204-001
4AIntegrated Circuit, 74180437-74LS04
4BIntegrated Circuit, 74LS7437-74LS74
4DIntegrated Circuit, 7418283137204-001
5AIntegrated Circuit, 7415163A37-74LS163A
5BIntegrated Circuit, 74153237-74LS32
5cIntegrated Circuit, EPROM, 2764-300136054-1101
5DIntegrated Circuit, 7418283137204-001
SE, 5FIntegrated Circuit, 741827337-74LS273
SJIntegrated Circuit, 7418158137203-001
5K, 5LIntegrated Circuit, 74LS194A37-74LS194
5MIntegrated Circuit, 741815737-74LS157
6BIntegrated Circuit, 74183237-74LS32
6DIntegrated Circuit, 741S17437-74LS174
6E, OFIntegrated Circuit, 741527337-7418273,
gIntegrated Circuit, 7418158137203-001
6K, 6L.Integrated Circuit, 74LS194A37-74LS194
6MIntegrated Circuit, 74LS15737-74LS157
7BIntegrated Circuit, 7487437-74874
7DIntegrated Circuit, 741817437-74LS174
JEIntegrated Circuit, 741817537-74LS175
TFIntegrated Circuit, 74LS8637-74L886
8BIntegrated Circuit, 7480437-74804
8CIntegrated Circuit, 74LS3237-74L832
8DIntegrated Circuit, 741S2037-741820
8EIntegrated Circuit, 741817437-74LS174
8FIntegrated Circuit, 74L$17537-74LS175
8KIntegrated Circuit, LB137536-001
8LIntegrated Circuit, EPROM, 27512-200136054-1117
8MIntegrated Circuit, 7483237-74832
9BIntegrated Circuit, 7487437-74874

5-17

Page 50

Illustrated Parts Lists Xybots

Xybots Game PCB Assembly Parts List, Continued

DesigaatorDescriptionPart No.
9CIntegrated Circuit, 74LS1037-74LS10
9DIntegrated Circuit, 74LS283137204-001
9EIntegrated Circuit, 74LS17437-74L8174
oFIntegrated Circuit, 74LS0437-74L804
OKIntegrated Circuit, LB137536-001
10AIntegrated Circuit, 74LS2037-74LS20
10BIntegrated Circuit, 74LS138137177-001
10CIntegrated Circuit, 74LS0037-74LS00
10DIntegrated Circuit, 74LS283137204-001
10EIntegrated Circuit, 7480037-74800
10FIntegrated Circuit, 74LS17437-74LS174
11AIntegrated Circuit, 74LS1437-74L814
11BIntegrated Circuit, 74LS3237-74L832
11CIntegrated Circuit, 74LS$25337-74L8253,
11D.Integrated Circuit, 74LS13937-74LS139
11E/FIntegrated Circuit, SYNGEN137419-103,
lyIntegrated Circuit, 74S0437-74804
1KIntegrated Circuit, 74815737-748157
MLIntegrated Circuit, EPROM, 27512-200136054-1103
12BIntegrated Circuit, 741824437-74LS244
12¢, 12DIntegrated Circuit, 74LS25337-T4L8253,
12)Integrated Circuit, 7488537-74885
12KIntegrated Circuit, 74L$3237-74LS32
12LIntegrated Circuit, EPROM, 27256-200 (OTP)136054-1102
13BIntegrated Circuit, 74LS24437-74LS8244
13CIntegrated Circuit, 74LS15737-74L8157
13DIntegrated Circuit, 74L$25337-74L8253,
13E, 13FIntegrated Circuit, 74LS27337-74L8273
13)Integrated Circuit, 74LS17437-74LS174
13KIntegrated Circuit, 74LS27337-74L8273
14BIntegrated Circuit, SLAPSTIC 7137412-107
14C, 14DIntegrated Circuit, 74LS25337-74LS253
14E, 14]Integrated Circuit, 8464D70137535-003,
14KIntegrated Circuit, GPC137419-101
14MIntegrated Circuit, 74LS3237-T4LS32
15BIntegrated Circuit, 741824437-741L8244
15CIntegrated Circuit, 74LS3237-74LS32
15DIntegrated Circuit, 741825337-7418253
16AIntegrated Circuit, 68000137289-003
16E, 16FIntegrated Circuit, 74LS37337-74L8373
17BIntegrated Circuit, EPROM, 27256-300136054-1114
17C/DIntegrated Circuit, EPROM, 27512-300136054-1112
17E, 17FIntegrated Circuit, 741824437-74L8244
17J, 17KIntegrated Circuit, RAM, 2K x 8, 100 ns137348-003
17LIntegrated Circuit, 740637-7406
17MIntegrated Circuit, 74L$260137332-001
18EIntegrated Circuit, 74L824537-74LS245
18F 18)Integrated Circuit, 74L824437-74LS244

5-18

Page 51

Xybots Illustrated Parts Lists

Xybots Game PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.
18KIntegrated Circuit, 741824537-74LS8245
18LIntegrated Circuit, 74LS27337-74L8273
18MIntegrated Circuit, 740637-7406
19BIntegrated Circuit, EPROM, 27256-300136054-1115
19C/DIntegrated Circuit, EPROM, 27512-300136054-1113,
19E, 19KIntegrated Circuit, 741824537-T4L8245
19LIntegrated Circuit, 74LS27337-T4LS273,
20C/DIntegrated Circuit, 2804A-45, 450 ns137329-450.
20EIntegrated Circuit, SCOM137526-001
20KIntegrated Circuit, 74LS260137332-001
20LIntegrated Circuit, 740637-7406
21EIntegrated Circuit, 74LS24437-T418244
21LIntegrated Circuit, 740637-7406

Capacitors

clCapacitor, 100 pE 100 V, Ceramic122016-101
C2Capacitor, 39 pF, 100 V, Ceramic122016-390
C3, C4Capacitor, .1 wE, 50 V, Ceramic122002-104
csCapacitor, 100 pF, 100 V, Ceramic122016-101
C6, C7Capacitor, .001 uF, 50 V, Ceramic122002-102
c8Capacitor, 100 pF, 100 V, Ceramic122016-101
C9-C16Capacitor, .1 wE, 50 V, Ceramic122002-104
C17Capacitor, 47 wF, 25 V, Electrolytic24-250476
C18-C29Capacitor, .1 wE, 50 V, Ceramic122002-104
30, C31Capacitor, 100 pF, 100 V, Ceramic122016-101
C32, C33Capacitor, .1 ¢F 50 V, Ceramic122002-104
C34-C36Capacitor, 470 pF, 50 V, Ceramic122013-471
37-C39Capacitor, .001 pF, 50 V, Ceramic122002-102
C41Capacitor, 100 pF, 100 V, Ceramic122016-101
C42Capacitor, .1 wE, 50 V, Ceramic122002-104
C43Capacitor, 47 uF, 25 V, Electrolytic24-250476
C44Capacitor, .1 zF, 50 V, Ceramic122002-104
C45Capacitor, 47 uF, 25 V, Electrolytic24-250476
C46-C102Capacitor, .1 wF, 50 V, Ceramic122002-104

Inductors

LIInductor, 100 pH141002-001
L2-L4Inductor, Ferrite Bead, N12N141003-005

Transistors

Ql‘Transistor, 2N390434-2N3904
Q2Transistor, 2N5306133033-001
Q3-Q5Transistor, 2N390434-2N3904
Q6‘Transistor, 2N390633-2N3906
Q7‘Transistor, 2N390434-2N3904
Q8‘Transistor, 2N390633-2N3906
Qo‘Transistor, 2N390434-2N3904
Q10‘Transistor, 2N390633-2N3906
Qll‘Transistor, 2N390434-2N3904
Qi2Transistor, 2N390633-2N3906
Q13Transistor, 2N390434-2N3904
Qi4Integrated Circuit, LM317137233-001
Page 52

Illustrated Parts Lists ‘Xybots

Xybots Game PCB Assembly Parts List, Continued

DesignatorDescriptionPart

Resistors

R1, R2Resistor, 10 kQ, +5%, 4 W110027-103
R4Resistor, 100 k®, +5%, %W110027-104
RSResistor, 2400, +5%, %W110027-241
R8, ROResistor, 1 kQ, +5%,%W110027-102
R10Resistor, 4700, +5%, %W110027-471
RILResistor, 1 kQ, + 5%, %W110027-102
R12Resistor, 4702, +5%, 4W110027-471
R14-R29Resistor, 1 k®, +5%, 4W110027-102
R31-R34Resistor, 470, +5%,4W110027-471
R35Resistor, 1 kM, 45%,4W110027-102
R36Resistor, 3909, +5%, 4W110027-391
R37-R39Resistor, 1 kQ, +5%,4W110027-102
R40Resistor, 4.7 k®, +5%,4W110027-472
R41Resistor, 2.4 kQ, +5%, 4W110027-242
R42Resistor, 1.2 kQ, +5%, 4W110027-122
R43, R44Resistor, 6209, +5%, %W110027-621
R45Resistor, 4.7 k®, +5%, 4W110027-472
R46Resistor, 2.4 kQ, 45%, 4W110027-242
R47Resistor, 1.2 kQ, +5%,'4W110027-122
R48, R49Resistor, 10 kQ, +5%, %W110027-103
RSO, R51Resistor, 4700, +5%, 4W110027-471
R52Resistor, 3 k@, +5%, 4W110027-302
R53Resistor, 3300, +5%, %W110027-331
R54, R55Resistor, 3900, +5%, 4W110027-391
R56Resistor, 4702, +5%, 4W110027-471
R57Resistor, 3302, +5%, 4W110027-331
R58Resistor, 4709, +5%,4W110027-471
R59Resistor, 3 kQ, +5%, %W110027-302
RGO-R62Resistor, 4702, +5%, 4W110027-471
R63Resistor, 100, +5%, %W110027-100
R64Resistor, 689, +5%, 4 W110000-680
ROSResistor, 109, +5%, 4W110027-100
R66Resistor, 682, +5%, 4 W110000-680
R67Resistor, 102, +5%,%W110027-100
R68Resistor, 682, +5%, 4 W110000-680
ROOResistor, 2402, +5%,4W110027-241
R70Resistor, 1 kQ, +5%,4W110027-102
R71Resistor, 1200, +5%, 4W110027-121
R72Resistor, 4709, +5%, %W110027-471
R73Resistor, 4.7 kQ, +5%, 4W110027-472
R74Resistor, 1.2 kQ, +5%, %W110027-122
R75Resistor, 2.4kQ, +5%, %W110027-242
R76Resistor, 6202, +5%, %4W110027-621
R78Resistor, 1 kQ, +5%, 4W110027-102
R79Resistor, 2409, +5%, 4W110027-241
R80Resistor, 4700, +5%, %W110027-471
R81Resistor, 4300, +5%, 4W110027-431
R82Resistor, 4709, +5%, 4W110027-471

5-20

Page 53

Xybots Iitustrated Parts Lists

Xybots Game PCB Assembly Parts List, Continued

DesignatorDescriptionPart
R83Resistor, 10kQ, 45%, 4W110027-103
R84Resistor, 3 kQ, +5%,4W110027-302
R85Resistor, 4700, +5%, 4W110027-471
R86Resistor, 3302, +5%,4W110027-331
R87Resistor, 3902, +5%,4W110027-391
R88Resistor, 680, +5%, 4 W110000-680
R89Resistor, 2400, +5%, 4W.110027-241
R90Resistor, 1.8kf, +5%, 4W110027-182
R91-R106Resistor, 4702, +5%,4W110027-471
R107-R117Resistor, 1 kQ, +5%,4W110027-102
R118-R120Resistor, 470, +5%, %110027-470
R121Resistor, 1kQ, +5%, 4W110027-102

Connectors

AUDConnector, 11-Circuit, Header, .100 Ctr, Key 5179118-011
DCConnector, 11-Circuit, Header, .100 Ctr, Key 5179118-011
JP2Connector, 2-Circuit, Header, .100 Ctr179048-002
PWRConnector, 12-Circuit, Header, .250 Ctr179069-012
RESConnector, 2-Circuit, Header, .100 Ctr179048-002
SWBConnector, 6-Circuit, Header, .100 Ctr, Key 2179118-006
SWAConnector, 11-Circuit, Header, .100 Ctr, Key 5179118-011
VIDConnector, 11-Circuit, Header, .100 Ctr, Key 5179118-011

Sockets 20-Pin Medium-Insertion-Force Socket 79-42C20 28-Pin Medium-Insertion-Force Socket 79-42C28 40-Pin Medium-Insertion-Force Socket 79-42C40 64-Pin Medium-Insertion-Force Socket 79-42C64

Miscellaneous

CRIDiode, Light-Emitting, Type-MV5053.38-MV5053
GND1, GND2Test Point179051-001

5-21

Page 54

Illustrated Parts Lists Xybots

a te

2F-YPH cy cl

(=ce¥cou

mm 73 Cea [| a

rye) tn bees | ie +o is REZ UE a ROD

eyo]| csssf3 Al
mS)hose 4UOa

gee RUS R3t eM Raw

23456

Figure 5-7 Stand-Alone Audio PCB Assembly A043713-21 B

5-22

Page 55

Xybots Illustrated Parts Lists

Stand-Alone Audio PCB Assembly Parts List

DesignatorDescriptionPart No.

Integrated Circuits

1J-CPUIntegrated Circuit, 6502A90-6013
1M-SCOMIntegrated Circuit, SCOM137526-001
2BIntegrated Circuit, LM32437-LM324
2DIntegrated Circuit, YM3012137402-001
2F-YAMIntegrated Circuit, YM2151137401-001
2H-RAMIntegrated Circuit, 6264-15, 150 ns137441-002
2K-ROMIntegrated Circuit, 27256, 300 ns136054-1116
2L-PALIntegrated Circuit, Programmed PALIGL8A, 25 ns136056-2101
3FIntegrated Circuit, 741837437-74LS374
4A, 4BIntegrated Circuit, LM32437-LM324
4MIntegrated Circuit, 74LS138137177-001
5C, 5DIntegrated Circuit, 4066B37-4066
5E 5HIntegrated Circuit, 741527337-74LS273
syIntegrated Circuit, 74LS240137251-001
5KIntegrated Circuit, 74LS7437-74LS74
gIntegrated Circuit, 741539337-74LS393
ALTCLKIntegrated Circuit, 741$39337-74LS393,
Q1, Q2Integrated Circuit, TDA2030137301-001
Q4Integrated Circuit, 7905, Standup37-7905

Capacitors

clCapacitor, .22 wE 50 V, Ceramic122015-224
C2Capacitor, 22 uF, 35 V, Electrolytic24-350226
3Capacitor, .22 wF, 50 V, Ceramic122015-224
C4Capacitor, .1 pF, 50 V, Ceramic122002-104
C5Capacitor, 22 uF, 35 V, Electrolytic24-350226
C6-C9Capacitor, .1 uF, 50 V, Ceramic122002-104
C12Capacitor, .1 uF, 50 V, Ceramic122002-104
C13-C16Capacitor, 100 pF, 100 V, Ceramic122016-101
cl7Capacitor, .1 uF, 50 V, Ceramic122002-104
C18-C21Capacitor, 3300 uF, 25 V, Electrolytic, Radial123003-338
C23,Capacitor, .1 »E, 50 V, Ceramic122002-104
C24Capacitor, 10 FE 25 V, Electrolytic24-250106
C25Capacitor, .22 wu 50 V, Ceramic122015-224
C26Capacitor, .1 ¢F, 50 V, Ceramic122002-104
27Capacitor, 10 uF, 25 V, Electrolytic24-250106
28Capacitor, .1 uF, 50 V, Ceramic122002-104
29Capacitor, .22 pF, 50 V, Ceramic122015-224
30Capacitor, .1 uF, 50 V, Ceramic122002-104
C31Capacitor, 10 wR, 25 V, Electrolytic24-250106
C32, C33Capacitor, .001 uF, 50 V, Ceramic122002-102
C34, C35Capacitor, .1 wR, 50 V, Ceramic122002-104
C38Capacitor, .1 4E 50 V, Ceramic122002-104
C41, C42Capacitor, .1 4E, 50 V, Ceramic122002-104
C43,Capacitor, 10 aE, 25 V, Electrolytic24-250106
Page 56

Illustrated Parts Lists Xybots

Stand-Alone Audio PCB Assembly Parts List

DesignatorDescriptionPart No.
C48-C52Capacitor, .1 wF, 50 V, Ceramic122002-104
C53Capacitor, .0022 yF, 50 V, Axial Ceramic122015-222
C54Capacitor, .0027 nF, 50 V, Ceramic122015-272
C55Capacitor, .001 wE, 50 V, Ceramic122002-102
C56Capacitor, .0027 nE 50 V, Ceramic122015-272
C57Capacitor, .001 wE 50 V, Ceramic122002-102
C58Capacitor, .0022 pF, 50 V, Axial Ceramic122015-222
C61-C68Capacitor, .1 wE, 50 V, Ceramic122002-104
C69Capacitor, 39 pF, 100 V, Ceramic122016-390
C70Capacitor, 100 pE 100 V, Ceramic122016-101
C71-C74Capacitor, .1 pF 50 V, Ceramic122002-104
C84Capacitor, .1 #F, 50 V, Ceramic122002-104

Diodes

CRI, CR2Diode, 1N400131-1N4001
CR3Diode, MV5053, Light Emitting38-MV5053,
cR4, CRSDiode, 1N400131-1N4001
CRODiode, MV5053, Light Emitting38-MV5053
CR7-CR10Diode, 1N540131-1N5401
R13Diode, MV5053, Light Emitting38-MV5053
R14, CR15Diode, 1N400131-1N4001

Inductor

LiInductor, 100 hH41-3003

Resistors

R1Resistor, 1k®, +5%, 4 W110000-102
R2Resistor, 10 kQ, 45%, 4 W110000- 103.
R3, R4Resistor, i 2, +5%, 4 W110000-010.
RSResistor, 1 kQ, +5%, 4 W110900-102
ROResistor, 10 kQ, +5%, 4 W110000-103,
RIOResistor, 02, % W110005-001E
R11Resistor, 1 kQ, +5%, 4 W110000-102
R12Resistor, 4709, 45%, 4 W110000-471
R13Resistor, 1 KO, +5%, % W110000-102
R14Resistor, 4700, +5%, 4 W110000-471
R15Resistor, 1 kQ, £5%, 4 W110009-102;
R16Resistor, 4702, +5%, 4 W110000-471
R17, R18.Resistor, 10k, +5%, 4 W110000-103|
RI9Resistor, 22k,15%, 4 W110000-223:
R20Resistor, 1 kQ, +5%, 4 W110000-102:
R21Resistor, 22 kQ, +5%, 4 W110000-223
R22Resistor, 100, +5%, 4 W110000-100
R23,Resistor, 5602, +5%, %« W110000-561
R24Resistor, 1k, 45%, 4 W110000-102
R26, R27Resistor, 100, +5%, 4 W110000-1004
R28.Resistor, 10 kQ, +5%, 4 W110000-103
R29Resistor, 1k0, +5%, 4 W110000-102
R33, R34Resistor, 4700, +5%, 4 W110000-471f
R35Resistor, 75 kQ, +5%, 4 W110000-753
R36, R37Resistor, 10 k®, +5%, 4 W110000-103
R38Resistor, 47 k®, +5%, 4 W110000-473
R43-R48Resistor, 12kQ, +5%, 4 W110000-123
R49Resistor, 10kQ, +5%, 4 W110000-103

5-24

Page 57

Xybots Ilustrated Parts Lists

Stand-Alone Audio PCB Assembly Parts List

DesignatorDescriptionPart No.
R50Resistor, 1 kQ, +5%, 4 W110000-102
R51Resistor, 10kQ, +5%, 4 W110000-103
R52Resistor, 10kQ, +5%, 4 W110000-103
R53, R54Resistor, 1k®, +5%, 4 W110000-102
R55, R56Resistor, 150 kQ, +5%, 4 W110000-154
R58Resistor, 1 k®, +5%, 4 W110000-102
R59Resistor, 150 kQ, +5%, 4 W110000-154
ROOResistor, 1 kQ, +5%, 4 W110000-102
R61Resistor Pot, 10 kQ, Horizontal, Dual119011-103,
R62Resistor, 7.5 kQ, +5%, 4 W110000-752
R63,Resistor, 30 kQ, +5%, 4 W110000-303
R64Resistor, 15 kQ, 45%, 4% W110000-153
ROS, R66Resistor, 12 kQ, +5%, 4 W110000-123
R67Resistor, 15 kQ, 15%, 4 W110000-153
ROBResistor, 30 kQ, +5%, 4 W110000-303
ROOResistor, 7.5 k®, +5%, 4 W110000-752
R74-R81Resistor, 1 k®, +5%, 4 W110000-102
R82Resistor, 4700, +5%, 4 W110000-471
R83,Resistor, 150 kQ, +5%, 4 W110000-154
R84Resistor, 0.0, 4 W110005-001
R85A,Resistor, 470 2, +5%, 4 W110000-471
R86Resistor, 2209, +5%, 4 W110000-221
R103Resistor, 150kQ, +5%, 4 W110000-154

Transistors

Q5-Q8Transistor, 2N390434-2N3904
Q9, Q10Transistor, 2N5306133033-001

Connectors

JACDCConnector, 12 Ckt., Header, .156-Inch Ctr., Key 11179213-012
JCDLConnector, 2 Ckt., Header, .156-Inch Ctr.179213-002
JCOINConnector, 6 Ckt., Header, .100-Inch Ctr., Key 2179118-006
JSCOMConnector, 11 Ckt., Header, .100-Inch Ctr., Key 5179118-011
JSPKConnector, 6 Ckt., Header, .156-Inch Ctr., Key 3179213-006

Sockets

1J-CPUSocket, Medium-Insertion-Force IC, 40-Contact79-42C40
2DSocket, Medium-Insertion-Force IC, 16-Contact79-42C16
2F-YAMSocket, Medium-Insertion-Force IC, 24-Contact79-42C24
2H-RAMSocket, Medium-Insertion-Force IC, 28-Contact79-42C28
2K-ROMSocket, Medium-Insertion-Force IC, 28-Contact79-42C28

Miscellaneous

HSLHeat Sink, TDA2030178190-032
QlNut/Washer Assy, 46-3275-99516
QlScrew, Pan-Head, Cross-Recessed, #6-32 x %-Inch72-16068
QI, Q2Compound, Thermal78-16001
swSwitch, Self-Test, Slide, SPDT69-004

Adhesive, Hot Melt 106006-001 Test Point 179051-001

5-25

Page 58

Illustrated Parts Lists Xybots

N O T E S

Page 59

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE The true state of a signal. For example: The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation.

ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as. operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING ‘Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks, Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

COMPLEMENTARY Having opposite states, puts ofa flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. such as the out-

Glossary

CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-tansistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure.

EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by applying high voltage. EPROM Erasable programmable read-only memory (see ROM). FLYBACK A step-up transformer used in a display to provide the high voltage.

Page 60

GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached toa piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. HISTOGRAM A special type of bar graph that shows how quantities are distributed. Histograms are included in the self-test of most Atari games, and typically show how long players play that game. Ic Integrated circuit. An electronic circuit in which all elements and the connections are made in or on a single semiconductor substrate, See also chip, IMPLODE To burst inward; the inward collapse of a vacuum tube. Bie) Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode, LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the vohage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4VDCto +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one highspeed data stream for simultaneous transmission On a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board.

PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted ona moving shaft. Used. chiefly as a voltage divider. Also called a ot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-tay tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE Ina raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from tight to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (eg., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repaiting a fault. VECTOR Aline segment drawn between specific X and Y coordinates on a cathode-ray tube, ‘WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE Aspecial diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Page 61

Xybots”

Date:

Coin Information and Game Statistics

Plyr 0 Coins Number of coins deposited in left coin mechanism Plyr 1 Coins Number of coins deposited in right coin mechanism Aux Count 0 Number of times players continued their characters at level 10 or earlier Aux Count 1 Number of times players continued their characters at level 11 and higher 0 Plyr Mins Minutes of idle time 1 Plyr Mins Minutes played as a 1-player game 2 Plyr Mins Minutes played as a 2-player game L Plyr Mins Total number of minutes that left player played R Plyr Mins Total number of minutes that right player played Total Games Total number of unique games played* Error Count EEROM errors

Total Coins Total number of coins deposited in both coin mechanisms Avg. Time/Coin Average game time per coin in seconds (including add-a-coin continuation games)

Histogram Information

Length of Length of Game in Number of Game in Number of Seconds Games Seconds Games

0-29 180-194 30-44 195-209 45-59 210-224 225-239

60-74 240-254 75-89 255-269 90-104 270-284 105-119 285-299

120-134 300 & up 135-149 150-164 165-179

"One "game" is the time between the first player starting and both players dying, regardless of time, number of coins inserted, or how many have played Xybots,

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and
  • Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 64

A.

ATARI

GAMES

Atari Games Corporation ® 675 Sycamore Drive * P.O. Box 461110 © Milpitas, California 95035