Spectar Technical Manual V1.1
Spectar (revision 3) (Exidy, 1980) · Manual · 34 pages · 6 sections · original scan
SPECIAR.
SPECIAR TECHNICAL
MARUAL
SPECTAR (TM)
Technical Manual 1.1
- 1988 Exidy, Inc. 399 Java Drive, Sunnyvale, California 94086 Telephone: (488) 734-9410 Toll-free: (896) 533-8462 Telex: 357-499
FOREWARD
This manual is designed for your ease in reading schematics. A description accompanies each schematic on the opposite page. This should help clarify the schematics and aid in your understanding of the technical aspects of SPECTAR.
The following is an outline of the information contained in the schematic descriptions: To find the particular information you are interested in, look up the schematic PAGE number as listed, and opposite the schematic is additional verbal explanation.
PAGE 4, GAME LOGIC PCB
- The 6502 Microprocessor (2A)
- Power-on Reset circuit (connected to 2A pin 48
- Processor Workspace RAM (4A, 5A)
- Main Address Decoding (5C, 5D, 5E)
Memory Map
PAGE 5, GAME LOGIC PCB
- Program Memory (6A through 13A
- PROM Address Selection (4B, 5B)
- Memory Device "Personality" Selection (11B)
PAGE 6, GAME LOGIC PCB
- Moving Object Horizontal Position (13F, 14F, 15F, 16F)
- Moving Object Vertical Position Counters (16E, 12E, 1, 13E)
- "Write Moving Object" Decoding (6F, 16H, 5E, 3F)
- Color Interface Output (16B)
PAGE 7, GAME LOGIC PCB
- Moving Object Multiplexing (14A, 14£) Moving Objects Image PROM (11D) Moving Object Video Output Shift Registers (12D, 13D, 14D, 15D
- Moving Objects Shift Register Load Logic (2F, 16H)
- Moving Object Shift Register Control Logic (15H, 14H
- Memory Device Personality Configuration (10D)
PAGE 8, GAME LOGIC PCB
- Interrupt Status Latch (8E
- Option Switch Port (15A)
- Control Inputs Port (9E)
- Moving Image Latch
- Audio Board Port
- Control Port Latch (9D)
- I/0 Decoding (7E)
PAGE 1, COLOR ADAPTER BOARD
- Character Generator RAM Division (1A, 2A
- Video Priorization
- Color Multiplexers (5A, 5B, 5C)
- SYNC and VIDEO Polarity (JPR1, JPR2)
- Output Level Adjustments (6C, 7A, 7C
APPENDIX A: PARTS LIST FOR SPECTAR
SCHEMATICS
1.
5. GAME LOGIC PCB
Oscillator (1D) From this oscillator all dynamic operations are derived, such as the processor clock, the main element and line counters, the shift register clocks, as well as all other forms of timing signals.
Element (Horizontal) Counters (1C, 1E, 2) ‘These components form the final stages of horizontal timing. All operations in this game requiring horizontal positioning or timing have their origin here. Note that, beginning with signal HCLK (from Clock Divide Counter 2), there are 256 counts prior to setting signal E256 high. When this signal goes high, itindicates that the horizontal blanking period isin progress. At this time the final counter (1E) is preloaded with a higher number than previously loaded. This creates a shorter count the second time. around. The shorter count measures the retrace interval. When the retrace count is finished, the counter preloads with a lower number, establishing a longer count sequence again for “real time” sweep of the electron beam across the face of the CRT.
Line (Vertical) Counters (4F, SF, 6E) ‘These components form the entire vertical timing operation starting with a clock derived from horizontal timing. These counters count 256 times and then preload with a higher number, causing a shorter count the second time. This shorter count measures the vertical retrace interval. Note that signal L256, when high, indicates vertical blanking is in progress. After the completion of the vertical retrace count, the counters once again preload with a lower number. This way they count 256 times during the sweep of the electron beam down the face of the CRT, allowing the horizontal timers to sweep one complete horizontal line for each count of the vertical counters. Thus, the electron beam reaches the bottom of the CRT, after completing 256 horizontal line sweeps. It then begins the vertical retrace count, and the whole cycle begins anew with the beam starting again at the top of the CRT.
Screen RAM Addresses (7D) During the time the screen RAM is examined by the logic for output to the monitor screen, addresses must be applied to the screen RAM to count up at a rate corresponding to the image cells conceptually arranged on the screen in a 32 x 32 matrix. The counts used here, 4 from the element counters, and 4 from the line counters, fulfill this timing requirement. The least significant element count used (E8) represents an interval exactly eight times that of one element. The least significant line count used represents an interval exactly eight times that of one horizontal line, or eight times a single line count. Dividing a 256 elementline by 8 yields 32, and likewise dividing a 256 line vertical sweep by 8 yields 32. Thus the screen RAM address lines (RAMO through RAMS) count ata rate that creates 32 horizontal counts and 32 vertical counts as the electron beam sweeps the face of the CRT. This makes 1024 conceptual “image cells” into which can then be inserted images of 8 elements by 8 lines. For more information concerning these images, refer to the text for page 3 of the Logic Schematics.
Coin Input Decoding (1H) Some models of SPECTAR contain two separate coin inputs for special coinage applications. NOR gate 1H combines these separate inputs, making signal SCOINT, which sets the interrupt flip-flop (6E on page 8) when either coin input becomes active, thus forcing the microprocessor to jump the interrupt service routine. This interrupt driven operation prevents ever missing a coin when inserted. However, this also means that when a game is first powered up, the coin input must be inactive. If for some reason the coin input switch is enabled at the time of power up, the game does not properly initialize until the switch is disabled. Hardware Generated Line Positioning Proms (3E, 4E) These PROMs are not used for SPECTAR. Generally their function is to create solid or dotted lines on the screen.
Blanking and Video Clocking (5H) Flip-flop 5H merely combines blanking and all other video.
Black and White Composite Video Output (1H) This circuit is not used for SPECTAR. If desired, however, these components may be installed to aid troubleshooting, by acting as a “video probe”
r | 2 Tl Tay “Bea THE TON Oo a ‘Daa Mnwese-ce a MOLAWEZNIS ORIN ONY DHS 2d 21907 IWS 2059 Pie ww YVINAdS
GAME LOGIC PCB
Screen Controller PROM (6D) This PROM controls the direction of data flow into and out of the screen RAM and character generator RAM. It prevents timing errors and buss conflicts, assuring that the microprocessor can write to either the screen or character generator RAM, or read back from either.
. Screen RAM (7B, 8B) The screen RAM is comprised of two 1024 x 4 static RAMs, configured to act as a single 1024 x 8 RAM. This creates a screen matrix of 32 horizontal by 32 vertical positions. A single byte code is stored in each of these positions to represent a particular character. During “real time” (the time the CRT is being swept by the electron beam) these character codes address the character generator RAM. Note that the PCB could substitute PROM for character generator RAM, but is not so configured for SPECTAR. These character codes, when used as addresses, are combined with the three least significant line counts (1, L2, L4) to present to the character generator output shift register all the necessary data to form an 8 element wide by 8 line high character on the CRT, located within one of the 1024 positions mentioned immediately above, that is, the 32 horizontal by 32 vertical positions. The screen, then, is a storage place for single byte codes that call up an 8 x 8 character and place it into the corresponding character cell. This character is stored in the character generator RAM, shown on page 3 of the schematic.
|. Character Image Storage Shown on this page are two PROMs (9C, 10C). They could be used as a permanent set of characters. However, SPECTAR uses RAM instead, to increase the flexibility in character manipulation. This portion of RAM appears on page 3 of the Logic schematics.
PROM Power and Signal Selection (108) This Dip Shunt configures the logic for different types of PROM devices. For SPECTAR, however, this Dip Shuntis unnecessary due to the fact that RAM has been used rather than PROM
Character Generator Output Shift Register (128) Video from the character generator memory devices (RAM in the case of SPECTAR) is formed by this shift register as a byte of data that displays one line ata time from left to right on the CRT. This ultimately forms an 8 line high by 8 element wide character Positioned on the screen according to the time it is presented to the shift register. Output from this shift register is all the images seen on the screen except the player image and the player missile image.
Ryo! £66 BD cy 0 oe
SCREEN RAMG) (Gwe. Cove =mense>] SPs" yore a we secvio
Rom
Ltt GiaRACTER GENERATOR viveo OUTPUT SWFT REGISTER
ae vere: 2a] Aor used eee Rea PROM, woe srecran Sex Pye 3
luseas [ie e cuawacrea ance STORACE Ze faye 3 fe Atenas RAM vsed =— poze HB -- 5 : fer pnaceam gewted 7 cleageable imagety= For ‘ se
power € SICAL SELECTION -— Wo sua : Ose0 Foe SPECTAR '
FF PPF PPR Bese dene lore
H 502 GAME LOGIC PCB zare Exticeri |
GAME LOGIC PCB Image Storage RAM
- Character Generator Image Storage RAM (13C, 11C, 14C, 12C) These four RAMs, when used in this configuration, act as a 2048 x 8 bit RAM. The images placed on the screen are stored in this RAM by the microprocessor, according to the game program. In this RAM images are established, altered, shifted slightly, and even replaced with a new set, if required by the program. When called by the logic to do so, the RAM presents, to the character generator shift register, a single byte, representing one line ofa particular image. Each image is composed of 8 lines of data, each line is one byte-wide. Thus, 256 images of 8 x 8 bits can be stored here simultaneously and “called up" by the screen RAM to be displayed on the CRT in any of the 1024 character cell Positions. A single byte code, stored in the screen RAM, calls up a character. The character may change or move by replacing the single byte code in the screen RAM, or by altering the data in the character generator RAM which forms the image.
vor ot Woe Yaa vos” a vor YS.
footed Rani
var] ines vas 1} Ram wea] ens at waa] rey ae
a
H Fy vos WOE OO
ed RAM wee
TMAGE STORAGE RAM
GAME LOGIC PCB
- The 6502 Microprocessor (2A) For detailed information concerning this microprocessor, refer to the MOSTEK publication, 6500-10A, MCS Microcomputer Family Hardware Manual. ‘One feature that should be mentioned here, however, is that this microprocessor has “memory-mapped I/O”. This means that all ports interfacing to peripherals of any type must be located within the normal memory map, with no duplication of addresses, since no instructions are specifically oriented toward I/O operations.
- Power-on Reset circult (connected to 2A pin 40) When powers first applied to a game, a particular sequence f events must occur to set up all logic conditions. If this sequenct broken for what ever reason, the microprocessor may become confused, and the game will not start and run. This sequence is accomplished when the reset line to the microprocessor is the last line allowed to reach a “high” logic level. The Power-on reset circuit makes sure this occurs by utilizing the charge time of an RC network as a delay, Ifany kind of power interruption occurs during normal game play, the power-on reset circuit insures that the microprocessor is reset. This alleviates thoroughly confusing the microprocessor while it also recreates the original power- on sequence.
- Processor Workspace RAM (4A, 5A) The RAM, or workspace, consists of the lowest 1024 bytes of memory and can be divided into three separate sections due to distinctly different functions The lowest 256 bytes (0 to FF Hexadecimal) is reserved for special software register operations, and is called “zero page”. The processor uses this area to store dynamic variables. For details of this type of operation, refer to 6502 technical literature regarding "Zero Page Addressing”. The next higher 256 bytes (100 to 1FF Hex) is reserved for the 6502 stack. The processor stores return addresses in the stack when interrupted or called to execute a subroutine. The game program may also request the processor to store other kinds of information here for later retrieval. The next higher 512 bytes (200 to 3FF Hex) are used as a scratchpad area. Miscellaneous calculations and their results are temporarily stored here.
4, Main Address Decoding (5C, 5D, 5E) This circuits the first stage of the address line decoding necessary to organize the memory map; thatis, it places specififunctions or devices within generalized blocks of the memory map, grouped by function For details on the addressing scheme, see MEMORY MAP, Figure 1.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME LOGIC PCB
- Program Memory (6A through 13A) These memory devices are 2716 EPROMS on Spectar. Note that four of the lines to each memory device (PC$0 through PC$7, PAP19, PAP20, PAP21) are programmable through jumper configurations located at 4B and 11B. This allows different memory devices to be used and/or it relocates the program memory within the memory map.
Some Spectar boards are configured for 2716 EPROMS needing only a single +5v supply, while others are configured for EPROMS requiring +12y, +5v, and -5v. REPLACING EPROMS without due regard to this configuration may destroy all program memory devices. If in doubt, please first contact the Exidy Service
Department for assistance.
- PROM Address Selection (4B, 58) This is a second stage of address decoding, used to select each individual memory device when addressed. Signal ROMSEL (trom page 4 Main Address Decoding) selects the Program Memory devices in general, and jumper 4B, together with decoder 5B further defines an address to a particular memory device.
- Memory Device "Personality" Selection (11B) The dip shunt, or jumpers block, alters power and signal configuration to the program memory devices. Note that the configuration shown on the schematic requires the use of 2716 EPROMS needing +12v, +5v, and -5v. PLEASE EXERCISE CAUTION regarding any change, in this configuration or replacement of memory devices.
Hex Address FEF7-FFFF 8201 5200 5103 5101 5101 5100 5100 50CO 5080 5040 5000 4800-4F FF 4000-43FF 0800-3FFF 0200-03FF 0100-01FF 0000-00FF MEMORY MAP Function or Device Interrupt and Reset Vectors Audio Board Tone Data Latch (write) Audio Board Control Latch (write) Interrupt Condition Latch (read) Control Inputs Port (read) Output Control Latch (write) (Not used in Spectar upright) Moving Objects Image Latch (write) Option Dipswitch Port (read) Moving Object 2 Vertical Position Latch (write) Moving Object 2 Horizontal Position Latch (write) Moving Object 1 Vertical Position Latch (write) Moving Object 1 Horizontal Position Latch (write) Character Generator RAM Screen RAM Program PROM Scratchpad RAM Stack RAM Zero Page RAM
PHOGEAR MEMORY
Oe woe
Be ese ° DAY Biles Be ane TERMINA
pares av | PROM paper ay] PROM
Pre Ringing Seppression
Parra ta SPLAT Reis] smone
Be pie SHUNT
PROM AvDRESS SELECTION Canbiquiation shou IMERORY DEVICE PERSONALITY 5 ee ceecran SELECTION EXIDY INC. 3502 GARETGGIC BCE
GAME LOGIC PCB
|. Moving Object Horizontal Position (13F, 15F, 14F, 16F) Counters 13F and 15F form a2 byte-wide counter which horizontally positions Moving Object 1 on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of the Horizontal Sync, they begin to count. The count outputs AND’ed through 15E give rise to signal M1HW, the Horizontal Position Window for Moving Object 1. Counters 14F and 16F are the equivalent circuit for Moving Object 2.
Moving Object Vertical Position Counters (16E, 12E, 1E, 13E) Counters 16E and 12E form a2 byte-wide counter which positions Moving Object 1 vertically on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of Vertical sync, they begin counting. The four count outputs of the least significant of these two counters (M1L1, M1L2, M1L3, M1L4) aresentto the moving object image PROM to specify which line of the image is presently being displayed. The AND’ed outputs of the second counter give rise to signal M1VW, the Vertical Position Window for Moving Object 1. Counters 11E and 13E are the equivalent circuit for Moving Object 2.
. "Write Moving Object” Decoding (6F, 16H, 5E, 3F) Consists of two distinctly different functions. 6F and 16H form the circuit that generates the load pulses for the moving object Position counters, while 5E and 3F simply prevent the counters from counting during blanking.
Color Intertace Output (168) This is a 14 pin DIP socket used as the connector interface to the color adapter board. The signals and their functions are:
Pin # 1 5SRLOAD = Shift Register Load Pulse (Neg. True) 2 CBLB = Composite Blanking 3 CSYNC = Composite Sync 4 SCVID = Composite Video (Neg. True) 5 SSCLK = Shift Register CLock (Neg. True) 6 HSYNC = Horizontal Syne 7 GND 8 VSYNC Vertical Sync 9 S5MO2VID Moving Object 2 Video (Neg. True)
10 SMO1VID Moving Object 1 Video (Neg. True)
11 VD7A09 Character Generator Address Line 9 12 SLINES NOT USED ON SPECTAR 13 VD7A10 Character Generator Address Line 10 +5V
pues 4 Wore: FoR SPECTER own O“TECT 1 = FLAveR HAGE (WnMED)
MovInG OBTECT 4 mOWNG OBTECT 2 Nol OBSECT 2 = MISSILE
VERTICAL CounTeRs| VERTICAL COUNTERS) sonal gp cone. mewn cpus) (7, | aiaeerwe
if ers 502 GAME LOGIC PCB —=7 =a] Z “A = (Gente Fos Mion Comers
GAME LOGIC PCB
- Moving Object Multiplexing (144, 14E) These two multiplexers pass information to the moving objects image PROM. They contain two codes: one determines which image should appear, and the other specifies which line of that image is to be displayed. ‘The data passed alternates between data for Moving Object 1 (player image) and Moving Object 2 (player missile), depending on the state of element count E32. The upper multiplexer (14A) passes the “which image” code, and the lower multiplexer (14E) passes the “which line of that image” code.
- Moving Objects Image PROM (11D) This PROM accepts as data the image and line codes of moving objects 1 and 2 (see "Moving Object Multiplexing” above). Itthen presents the appropriate data for one line of the image to the output shift registers. The timing of the logic insures that the correct pair of shift registers are loaded with the data, then shifted out at the correct ti to become, one line at a time, the 16 lines of video for that character (Moving Object 1 or 2).
- Moving Object Video Output Shift Registers (12D, 13D, 14D, 15D) Shift registers 12D and 13D together form a 16 bit shift register whose task is to accept, as data, 16 bits (2 bytes) representing a single line of the image for Moving Object 1, then shift these 16 parallel bits out serially to become video. This operation is repeated for 16 consecutive lines, resulting in a video image that is 16 bits wide by 16 lines high on the monitor screen. Shift registers 14D and 15D together form this same type of circuit, identical in function, for Moving Object 2.
4, Moving Objects Shift Register Load Logic (2F, 16H) This circuit sends properly timed load signals to the Moving Object Video Shift Registers. These load signals are needed to load the image data into the shift registers at location 12D or 14D.
- Moving Object Shitt Register Control Logic (15H, 14H) The input signals to the upper two gates (15H) represent horizontal and vertical position “windows” for the two moving objects (for example, M1HW Moving Object 1 Horizontal Window, M2VW Moving Object 2 Vertical Window). These windows allow the Moving Object shift registers to shift only at the right time. This insures the image is generated at the correct position on the screen. The lower 2 gates of 15H are, in Spectar, used only for later decoding on the color adapter board.
- Memory Device Personality Configuration (10D) This is another Dip Shunt which reconfigures the PC board in order to use a PROM (11D) of another type or manufacturer.
TELE oot ls mime moral Ws wen.
ieu0-1
moving OB TECTS SuieT REGISTERS ‘LeAD LOGI Tmace Seuccrion Loci ‘ancak Mosiny ObJeCP? na ae line swowor 2 smozvor movin OBSECTS SHIET REGISTERS CONTROL LOGIC TOE GRE TOSTE PE So ae EE Tore riven
GAME LOGIC PCB
- Interrupt Status Latch (8E) This latch is set when a coin is dropped or vertical sync occurs. When the latch is set, the CPU is interrupted, that is, signal IRQ goes low. This forces the CPU to jump to the interrupt service routine. The interrupt service routine instructs the CPU to check for a coin input, and then run a debounce routine on the coin bits of ports SE or 15, depending on which coin input bit was set at 8E. Ifthe CPU finds no coin input bit set at latch 8E, it will assume the Interrupt condition was caused by vertical sync. This tells the CPU that it should now jump to the routine that services the normal game play, and that the screen can now be updated with new data. The screen can only be updated during the vertical retrace interval.
- Option Switch Port (15A) This port provides input from the option dipswitch, at location 16A. Data from the dipswitch is gated onto the data buss and read by the CPU at game start. This allows such options as number of turns, coins per game, additional game versus extra turn, etc.
- Control Inputs Port (9E) This port provides input from the controls located on the control panel, such as the joystick, fire button, one player start, and two player start. Data from these controls are gated onto the data buss for examination by the CPU during the regular service routine (which is synchronized to the vertical interval).
4, Moving mage Latch Only the CPU can write to the moving image latch. This latch contains the code that specifies which image or images are presently being displayed by the hardware moving object circuitry,
- Audlo Board Port This latch is written to only by the CPU and transmits instructions to the audio board when any sounds are enabled, disabled, or the game is initialized. For the functions of these instructions, see the audio board schematic and/or description of operation.
- Control Port Latch (9D) This latch, used only in the Spectar cocktail table versions, is written to only by the CPU and keeps track of which player is “up”, in order to select which controls are active, that is, player one or player two.
- VO Decoding (7E) The upper half of this decoder generates the chip selects for those devices written to by the CPU, and the lower half generates the chip selects for those devices which are read by the CPU. See the detailed memory map for more precise information.
sigs TF ‘ena°Si804 SVD 2059 me (7 =
AUDIO BOARD
|. Address Decoding (1D) Uses the audio board select signal ABSEL, the 02 AND’ed write signal WRITE, and Address Line AO to decode the addresses for two input latches. These two latches each receive a byte of data from the CPU instructing the audio board what to do and when.
. Control Data Latch (2C) This latch receives a byte of data from the CPU that sets those particular bits directly used as sound enables. Signal TONE is the enable for the programmable tone (or music) generator. Signal CRASH is the enable for the crash or explosion sound. Signal SHOOT is the enable for the player (Wummel) firing saund. SPECTAR does not use signal CPU MUSIC.
}. Tone Data Latch (2D) This latch receives a byte of data from the CPU that becomes the preload for the most significant counters of the Tone Generation circuit. Varying this preload allows generation of a variety of tones used for music or special effects.
. Tone Generation Circult (1A, 1B, 3A, 3B, 3D) Counters 1A and 18 divide the 02 (phase two) processor clock down from approximately 706 Khz to approximately 34 Khz. This frequency establishes a range of tones accurately generated by merely changing the preload of the two most significant counters in this circuit, 3A and 3B, Flip-flop 3D divides this tone by two again, while transforming a narrow terminal count pulse train into a pulse train having a50% duty cycle. This means itis at a logic high for the same amount of time it is at a logic low, causing a more pleasing sound to the ear. The output of this circuit is then fed to the input of the summing amplifier.
j.. White Nolse Generation (6D) Transistor Q4 is the source of this white noise, as its base-emitter junction is broken down by excessive reverse bias. This throws the junction into heavy electron agitation (thermal emission) which activity produces noise across a wide bandwidth. Operational Amplifier 6D is used merely to boost the output amplitude of this noise, and transistor Q5 serves as an output buffer stage to prevent loading of the operational amplifier.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
AUDIO BOARD
- Shoot Sound Generation (5A, 4A) Both segments of timer 5A are configured to act as free-running multivibrators. The segment on the right receives, as control voltage input, the psuedo-triangle wave created by the charge and discharge of the RC network of the left segment. This creates, in the right segment, a frequency that increases and decreases at the rate of the triangle wave rate. This effectively simulates reverberation. This reverberated tone is then fed to amplitude modulator 4A, whose output amplitude is controlled by the voltage applied to pin 2. Normally (in the quiescent condition) transistor Q1 is in a saturated state, holding 4A pin 2 ata level just under 6 volts. This prevents any audible output from 4A. When signal SHOOT is enabled (set high), transistor Q1 is cut off due to the base being dragged low. This drops the voltage on 4A pin 2 low causing the output amplitude of 4A to increase, creating the player firing sound. Note that both the leading and trailing edge of this amplitude-modulated tone package are made gradual (sloping) due to (for the leading edge) the discharge time of C60, and (for the trailing edge) the discharge time of C14.
- Explosion/Crash Sound Generation (Q3) Normally (quiescent condition) transistor Q3 is not base-biased to conduct, therefore the white noise applied to the cathode of CR2 is never passed through the circuit. When signal CRASH is enabled (set high), C35 is allowed to charge through CR1 and R25 toward +12v. As this voltage increases, the base of Q3 receives increasing current and begins to pass the white noise. This circuit is configured to act as an active filter, so the frequencies passed are only those selected for a reasonable crash or explosion sound, The trailing edge of the explosion/crash decays slowly when signal CRASH is disabled (set low) since the discharge path for C35 is through a relatively high resistance (R24), Output of this circuit is also then routed to the input of the summing amp.
- Summing Amplifier and Integrator (5B) ‘Two segments of an LM324 operational amplifier are used here. The first is configured as a summing amplifier. Itis the common point at which all the various sounds are algebraically added to become one signal. This signal is the composite of all individually developed sounds. This is also the location of the master volume contro! (R22)
- Audio Amplifier (6A) The final audio amplifer isa single IC (6A), configured as a bridge amplifier. The composite audio signal is applied to the input ot ‘one of the two internal segments and the output swings in accordance with the input signal. The feedback on this segments not only fed back to the inverting input of the same segment, but is also applied to the inverting input of the other segment. This creates a condition wherein one segment swings positive, and the other segment simultaneously swings in a negative direction, creating an output twice the voltage of a single segment.
(i
a N-9086-20 | z| spargioade armiogge 529/00 sperspoom wi aim sonjen amped iy
sprigioads 2emings2 Sanna dounnyee BS 4 Wf fsmyo er 940 S3nj0a sepsony tly oan Aine eepe 10 ayaa prgordan yom SOT IY 4 023 "12 (249419 waumye 36 mop gee) Biyioedes S008 hese ‘g500p>'t20's12 829°€29°89°99'b9~19 Gapias gto) auyionden so0dhg ass “euEwT ve glewT 17 ase ap nospounb gers goo sage ef pose ines a Been fey woxpuent Bpenipyy nmeys suedwor * Qn wt yataramy orany
DiaywsHes aod Olany ¥¥i23dS
erral awnron = Hoey andes
orn lon 1 bby BWaT0A 33st yoaysgaint amy orem yew! <a ress
be bape Sa SOTA Nosdw3H99 aNnOs HS¥32/ NOISOTsXa be wD ao 7 ob 3 RD oe NOHLWHaNID GNADS LOCHS
COLOR ADAPTER BOARD
- Character Generator RAM Division (1A, 2A) The combination of flip-flop 1A and decoder 2A divides the character generator RAM into 4 equal segments, using the uppermost 2 address lines from that circuit (VD7A09, VD7A10) and the composite video signal (SCV1D). The resulting 4 video lines are then applied to the input of the priority encoder at 2B.
2, Video Prioritization (2B) All video outputs from the Logic Board are applied to priority encoder 2B. As mentioned in the discussion of “Character Generator RAM Division", above, the single character generator output has here been separated into 4 different lines, each carrying the video imagery stored in a different quadrant of character generator RAM. These four lines are applied to the priority encoder along with the video output lines from Moving Object 1, Moving Object 2, and signal SLINES, not used for SPECTAR. ‘As shown on the schematic, the input prioritization is from top to bottom. Thatis, highest priority is assigned to the input shown at the top (5MO1VID) and the lowest to the input at the bottom. The lowest in this case is actually tied low in order to be always. active, which creates the background color. The code present on tite output of 28 indicates the number of the highest priority video line active at that time. This code is then applied to the Color Multiplexers to select the appropriate RGB output code for that video imagery.
- Color Multiplexers (5A, 5B, 5C) Each of these multiplexers generates the final video output for a particular base color: red, green, or blue. The priority code from 2B is applied to the multiplexer select lines. This causes all multiplexers to simultaneously output data according to the priority code, and output the data from a particular input pin. The data on each input pin is set up by jumper configuration. Thus, in parallel, 5A, 5B, and 5C consider two factors when outputing RED, GREEN and BLUE data: the code of the highest priority video present, and the associated jumper configuration establishing the color of the video.
- SYNC and VIDEO Polarity (JPR1, JPR2) Exclusive OR gates 6A and 1C have here been configured to act as “selectable inverters”. Cut the VID jumper (JPR1) and the output video is inverted to become negative true. The same occurs with the SYNC jumper (JPR2). Note that composite sync is available as well as separate Horizontal and Vertical sync outputs. When JPR2 is cut, it inverts all three sync outputs.
5, Output Level Adjustments (6C, 7A, 7C) The only time these inputs are used is with a monitor requiring unusual input levels. They are not used on SPECTAR.
Smowip @ pala __ 4 >
SMO2VIO = sews ra8139 2A
wpran mist
SEED) ——SSRLD fos ot _ Gare PD) cout Se Gm)
(CEE eee cA hs ¥we mar [F DHS cov BED)
i Ges 5S warner
Sep seme Gr veer Me CT)
8 T 7 | 6 5 . 4 3 2
APPENDIX A
PARTS LIST FOR SPECTAR
Control Panel Assembly
Part Number 68-2933-13 75-5177-16 72-3622 38-5976-18 38-5044-10 74-5247 74-6506 71-2391 Description
control panel control panel PSA polycarb silkscreen overlay switch pushbutton with nut and washer control 4-way joysick, long assy. Midway white pushbutton switch assy. carriage bolts 10/24 x 5/8 L black full thread kepnut 18/24 control panel harness
Universal Power Supply Assy
Part Number
78-3001 63-4928 or 63-4925 or 63-4035 77-3365-15 71-2389-10 76-1211-18 74-3503
74-5198
74-3502 74-3508 74-4604 61-8872 61-8656 61-8854 88-4902 88-4081 88-4928 88-4008 88-4911 Description
+5VDC Power Supply 6AMP aux. transformer T911
aux, transformer T893
MPG pin 773P9 power supply PCB Assy. power supply harness power supply mounting board screw, #6x1/2 1 phillips pan head selftap screw, #6-32x 3/4 pan hol. phil. machine kepnut 6-32 washer #6 Amer. std plain hex nut 8-32 nylon butt splice, blue plug, 2 pin molex pins, male molex tie wrap, small tie wrap, large wire, 22 ga. buss-uncoated solder SN69 .03 dia. 58 core flex mask and mold seal
American Standard Double Coin Door
Part Number
66-4963 66-4907
71-2396 64-2088 88-4902 61-8313 74-3562 Description
Std. double coindoor, Vendall 25 cent Amer. coin acceptor Coin door key (supplied w/ 66-4003 Universal coin door harness coin meter tie wrap, small butt splice red 6-32 kepnut
British/Australian Coin Door
Part Number Description
66-4013-198 Std. British/Aust. dbl. coindoor w/ 10P/50P Coin door key supplied w/ 66-4913-10 71-2417 Aux. coin harness 64-2008 coin meter 61-8313 butt splice red 71-2390 univ. coin door harness 74-3562 6-32 kepnuts
Pushbutton Assy
Part Number Description
72-3061 switch assy. 72-3862 push button 74-0203 pal nut
Spectar Speaker Assy
Part Number Description
62-7061 6" x 9" oval speaker 61-8056 conn. 2 pin male molex 93-09-2622 61-8054 pins, male molex 82-99-2118
Monitor Isolation Transformer Assy.
Part Number Description
FR 63-4829 Isolation transformer Midwest 773P7 61-8958 Molex connector 03-09-2032 61-8054 male molex pins 62-69-2118 61-8057 molex connector 83-99-1023
61-8055 female molex pins 02-09-1118 76-1212-58 XFMR mounting board 71-2001-14 xfmr harness 61-8072 butt splice blue 74-6402 washer, #10 plain 74-6506 kepnut 19-24 74-5463-01 screw, 10-24 x 1" ph phil mach 74-5165 fender washer 1/4 ID 1 1/4 OD 88-4002 tie wrap small 61-8313 butt splice red Reference Location
P4
Reference Location
AC INPUT 22 P22 AC to Monitor J23 J23
Audio PCB Assembly
Part Number
48-2321 48-2314 48-2071 48-2308
48-2218 48-2342 48-2212 48-2221 48-2211 48-2015 48-2382 47-3005 46-3030
59-5118 59-5109 54-5021 54-5019 59-5078
59-5125
59-5163 59-5025
59-5055 59-5080
59-5140 59-5069 59-5058 59-5120 59-5095 59-5045 59-5040 59-5038 59-5065 23-4030 23-4035
23-4615
21-4028 23-4070 Description
74L8139, IC 74LS374, IC 74LS112, IC 74LS161, IC
72748, IC LM324 NE 556 MC 3348 LM379 (Dual 6W Audio Amp National 7407 74 Lso4 2N 3904, trans IN 4454, trans
resistor, 2.2K 1/4 w 5% resistor, 3.3K 1/4 w 5% potentiometer, 100K potentiometer, 10K resistor, 22K 1/4w 5%
resistor, 1K 1/4w 5%
resistor 820K 1/4w 5% resistor 1 meg omega 1/4 w 5%
resistor, 47K 1/4 w 5% resistor, 10K 1/4 w 5%
resistor, 100K omega 1/4w 5% resistor, 120K 1/4w 5% resistor, 68K 1/4w 5% resistor, 1.2K 1/4w 5% resistor, 4.7K 1/4w 5% resistor, 100K 1/4w 5% resistor, 150K 1/4w 5% resistor, 560K 1/4w 5% resistor, 33K 1/4w 5% cap, .22 uf ceramic disk cap .1 uf ceramic disk
cap, 6.8 uf 25v dip. tant.
cap, 2.2 uf 15v dip. tant cap, 22p£. ceramic disk Reference Location
1D 2c,2D 3D 1A,2A,1B,3B, 3A 6D 5B 5A 4a 6A 4c 1¢,3C 01,03,04,05 CR2, CR3, cR4, CR1 R7 R14 R35 R1,R22,R38 R19,R31,R32, R37 R33,R40,R45, R13 R41 R9,R16,R17, R42, R47 R43 R12,R34,R46 R48 R44 R4, R24 R3 R2,R25,R5, R21, R49, R6 R28, R15 R26 R27 R18, R39 c44 c9, C12, c17, C31, C34, C37, c43 c14, c2l, C22, C40, c46, C47 c48, C49 c45
Audio PCB Assembly (continued)
Part Number
23-4060 23-4058
21-4010 22-4625
61-8042 68-3041
22-4632
74-2586 72-3025
74-5065 or 74-5075 77-3371 74-5182 Reference Description Location
cap, .@01 uf ceramic disk on cap, .61 uf ceramic disk Cl, C2, C3, C4, C6, C7, c8, Cl6, C24, C25, C27, C23, C30, C33, C38, C39 cap, 33 uf 25v dip tant. C19, C20 cap, .47 uf 25v dip. tat. C15, Cla, C68 conn., 108 pin female J2, 53 heat sink, thermalloy 6072 6A (use only w/ LM 379 caps, 18 uf Radial tant or mini cl4, C5 electro 25V screw, 4-46 x 1/4" machine 6A heatsink dip pka. shunt 16 pin 6B AMP Part # 435704-8 standoff 6-32 x 5/8" nylon
standoff 6-32 x 1/2" nylon Spectar, audio (bare) PCB 6-32 x 1/4 machine screw
Universal Power Supply PCB
Part Number
77-3365-14 20-4008 21-4610 21-4015 46-3016 47-3004 47-3041 47-3611 48-2337 48-2217 48-2338 68-3041 69-2638 61-8018 74-2514 74-5216 74-5191 Description
printed circuit board 40066 uf 50 v axial lead capacitor 33 uf 25 v dip tantalum capacitor 6.8 uf 35v dip tantalum capacitor 6@si diode mda 970-1 bridge rectifier "N3055 transistor 2N6246 transistor 7985T negative 5v LM326T-5 regulator 7912T negative 12v LM320T 12 regulator 7812T positive 12v LM349 T-12 regulator thermalloy 6072 heat sink thermalloy 6015 heat sink 12 pin male molex 4-40 x 3/8 phillips pan head machine screw #4 flat metal washer #4-40 kep nut
6502 Game Logic PCB Assembly
Part Number Description
48-2000 Ic 7406 48-2095 IC 7482 48-2010 Ic 7464
48-2015 IC 7487 48-2020 IC 7468 48-2332 Ic 74Lsll 48-2035 Ic 7428 48-2316 Ic 74LS21 48-2045 Ic 7427 48-2055 Ic 7432 48-2067 Ic 7474 48-2071 Ic 74LS112 48-2307 Ic 74LS138 48-2321 Ic 74LS139 48-2090 Ic 74157 48-2095 Ic 74161 48-2100 Ic 74166
48-2115 Ic 74193
48-2328 Ic, 74LS241
48-2356 tC 74LS245
48-2314 Ic 74LS374
48-6502 microprocessor 6542 48-2334 2114 (1K x4) RAM
48-9125-@1 2708 EPROM (1K x 8) HRL 11D-1 48-9999-81 6331 PROM (.32 X 8) 48-9099-62 6331 PROM (.32 X 8 48-9144 6301 PROM (256 X 4) 46-3025 IN4862 diodes 59-5135 res. 470 omega 1/4 w 5% 59-5126 res., 1.2K 1/4w 5% 59-5115 res., 1.8K 1/4w 5% 59-5118 res., 2.2K 1/4w 5% 59-5105 res., 2.7K 1/4W 5% 51-003 res., 220 omega 1/4w 5% 10 pin sip 51-6082 res., 2.2K 1/4w 5% 19 pin sip 51-9001 res., 4.7K 1/4w 5% 19 pin sip Reference Location
3D, 15H 1H, 6H 1D, 3F, 4D, 10F, 11F 2c SE 3H 2F 12F, 15E TF, 2H 6F 1c 2E, 6E 5B, 5D 7E, 16H 14a, 146 1E,2D,4F,5F 12B, 12D, 13D, 14D, 15D 10E, 126, 13F, 15F 14F, 16F, 11E,13E 8c, 1A, 3A 3B, 4H, 6B, 7D, 9B, 9E, 15a 3c, 4C, 6C 15B, 13B 1F, 14B, 7C, 8E 2A 4A, 5A, 7B, 8B, 11C, 12C 13¢c, 14¢ 11D 6D 14H 5c 8E, 9E, 2H 1D, 2H 2c 1c, 2c 7B, 2A ic, 2c 9E 16A 15A
6582 Game Logic PCB Assembly (continued)
Part Number
51-8004 23-4033 23-4035
21-4015
20-4014 20-4085 72-3825 72-3042 45-3836 61-8041 61-8062 77-3374 61-8645
61-8035 61-8069 61-8157
21-4621 49-5138
59-5064 23-4067 48-9143-91 48-9143-62 48-8143-03 48-9143-04 48-9143-05 48-9143-66 Description
res., 6.8K 1/4w 5% 10 pin sip cap, .61 uf ceramic disc cap, .1 uf ceramic disc
cap, 6.8 uf 25v tant. dip
cap, 33 uf 25v electrolytic cap, 470 uf lav electrolytic dip shunt jumper paks 16 pin dip switch 8 pos. crystal, 11.289 connector 16 pin molex dip sockets 16 pin low profile print. circuit board dip socket 24 pin low profile
dip socket 4@ pin low profile dip socket 14 pin low profile dip socket 18 pin low profile
cap, 1 uf 25V dip tant res, 220 v 1/4 w 58
res, 180hm 1/4w 5% cap, 330 pf cer. disk 2716 EPROM programmed SPL6A-1 2716 EPROM programmed SPL7A-1 2716 EPROM programmed SPLBA-1 2716 EPROM programmed SPLAQA-1 2716 EPROM programmed SPL1GA-1 2716 EPROM programmed SPL11A-1
6502 Color Adapter PCB Assembly
Part Number
48-2080 48-2305 48-2321 48-2079 48-2341 48-2333 20-4015 59-5136 59-5183 23-4033 61-8203 61-8127 77-3373-14 Description
Ic 74151 IC 74LS74 Ic 74LS139 Ic 74148 Ic 74LS86 IC 74LS174 6.8 uf dipped tantalum capacitor resistor 338 omega 1/4 w 5% 9 pin sip resistor pac 1K omega +@1 uf ceramic disc capacitor 18 pin male molex connector 14 pin socket stan profile w/ lock printed circuit board Reference Location
14a 1D A/R per assy drawing 1c, 6E, 15D, 13F Ic 2c 10H 4B, 10D, 11B 16A 1D 16C, 16E 5C, 6D, 14H
11D,6A,7A,8A 9A, 10A, 11A 2A 16B 44 5A 7B 8B llc 12¢ 13c 14c C45, C52 R200, R311 at 5D R3886-R308 5D
Reference Location
5A, 5B, 5C 1A 2A 2B Ic 6A 6B cl Rl thru R10 3A, 3B, 3C c2 C4 C5 C6 P2 Jl