Ultra Tank TM-107 1st Printing
Ultra Tank (Atari (Kee Games), 1978) · Technical Manual · 112 pages · 58 sections · original scan
‘TM-107 1st PRINTING
KEE GAMES @ wholly owned subsidiary of Atari, Inc.
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service. tee
Ultra Tank*
Operation, Maintenance and Service Manual
Complete with Hllustrated Paris Catalog
ATARI INC 1265 BORREGAS AVENUE SUNNYVALE, CALIFORNIA 94086 408/745-2000 = TELEX 35-7488
FA. KEE GAMES a wholly owned subsidiary of Atari, Inc
(w'] A Warner Communications Company
Copyright © 1978 by Atari, Inc. All rights reserved Motorola and TEC service manuals reprinted by permission of Motorola Data Products and TEC Videoelectronics, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write:
ATARI INC 1265 Borregas Avenue P.O. Box 9027 Sunnyvale, California 94086
2G
Lithographed in the U.S.A.
TABLE OF CONTENTS
1 LOCATION SETUP A. INTRODUCTION . 1 B. GAME INSPECTION. 2 C. LOCATION OF SERIAL NUMBER 3 D. INSTALLATION REQUIREMENTS 3 Power Requirements and Line Voltage Selection 3 Temperature Range . 4 Humidity Range .. 4 Location Space Requirements 4 Type of Power Cord ... 4 £. INTERLOCK AND POWER 4 F. SELF-TEST PROCEDURE .. 4 G. OPERATOR OPTIONS .... 4 H. VOLUME CONTROL 7
2 GAME PLAY A, ATTRACT MODE. 9 B, READY-TO-PLAY MODE 10 C. PLAY MODE 1
3 eae por maeal AND ADJUSTMENTS CLEANING .14 6 COIN MECHANISM . 14 Components on Coin Door .. .14 Access to Coin Mechanisms . 14 Cleaning of Coin Paths ...... .15 Adjustment of Coin Switch Trip Wire .......... 215 Mechanical Adjustments on Coin Mechanism . 16 General Troubleshooting Hints ........ 18 C. FUSE REPLACEMENT . . 18 D. TV MONITOR REMOVAL .. . 18 E. TV MONITOR ADJUSTMENTS i . 18 G. LED START SWITCH AND OPTION SWITCH REPLACEMENT .. ven ID G. JOYSTICK REPAIR oo... cette tect ete enn ee 21
4 THEORY OF OPERATION GENERAL INFORMATION . 23 POWER SUPPLIES .......... . 24 CRYSTAL OSCILLATOR AND TV SYNC COUNTDOWN CHAINS . 24 MICROCOMPUTER ... - 24 MICROCOMPUTER WATCHDOG . MOTION GENERATOR ... PLAYFIELD GENERATOR .. VIDEO OUTPUT .. ADDRESS MAP ... >Za™moOR>
TABLE OF CONTENTS
5 ILLUSTRATED PARTS CATALOG. ..................
6 TV MONITOR SERVICING INFORMATION MOTOROLA Service Manual A. GENERAL INFORMATION . B. SERVICE NOTES Circuit Tracing. Component Removal CRT Replacement ... Adjustments ...... Regulator Adjustment Horizontal Hold/Oscillator Adjustment . Vertical HeightiLinearity Adjustment Focus Adjustment ... Monitor Servicing ... C. THEORY OF OPERATION Power Supply ..... +73 Volt Supply Video Amplifiers and Output .. D. HORIZONTAL DEFLECTION CIRCUITS . Phase Detector ....... Horizontal Oscillator .. Horizontal Pulse Shaper and Driver .. Horizontal Output Sync Circuits ....... Vertical Oscillator and Output . Spot Killer .......... Blanking Amplifier TEC Service Manual
A, GENERAL B. SPECIFICATIONS Power Supply Input . Power Consumption Video Input Picture Tube . High Voltage ........... Horizontal Retrace Time . Resolution Scanning Frequency ... Tone Burst Amplifier Environment «72 . 74 . 74 . 74 +. 74 . 74 . 74
. 75
. 75
.. 78
. 78 . 78
. 60
. 81
LIST OF ILLUSTRATIONS
Figure 1-1 Location of Voltage-Changing Plugs on the Power Supply ........... 3 Figure 1-2 Location of On/Off, Interlock, Self-Test, and Volume Control Switches 5 Figure 1-3 Caution Label On Game PCB .. Figure 2-1 Attract Mode Figure 2-2 Ready-To-Play Mode . Figure 2-3 Play Mode Figure 3-1 Coin Door Assembly ae Figure 3-2 Hinging Open the Magnet Gate Assembly Figure 3-3 Removal Of Coin Mechanism ........... Figure 3-4 — Surfaces to Clean Inside the Coin Mechanism Figure 3-5 Removal of Plate Covering Rear of Coin Slot .. Figure 3-6 | Close-Up View of Lubrication Point Figure 3-7 Detail View of Coin Switch and Trip Wire . Figure 3-8 Securing the Coin Switch Trip Wire Figure 3-9 Adjustments on Coin Mechanism . Figure 3-10 TV Monitor Removal ... Figure 3-11 Locations of Adjustments on TV Chassis . Figure 3-12 LED START Switch and Option Switch Replacement . Figure 3-13 Joystick Removal Figure 4-1 Ultra Tank PCB Block Diagram . Figure 4-2. Game Block Diagram Figure 4-3 Ultra Tank Schematic Diagram (6 sheets) Figure 4-4 Playfield Generator Character Trace ...... Figure 5-1 Ultra Tank Final Assembly Figure 5-2. Control Panel Assembly .... Figure 5-3 Joystick Assembly (Up, Down, and Fire) . Figure 5-4 Joystick Assembly (Dummy Button) . Figure 5-5 TV Shelf Assembly ... : Figure 5-6 Coin Door Assembly ..... Figure 5-7 Power Supply Assembly .. Figure 5-8 RF Shield PCB Assembly Figure 5-9 Ultra Tank PCB Assembly Figure 5-10 Harness Schematic ...... Figure 6-1 Motorola Monitor Circuit Board in Service Position . Figure 6-2. Motorola Monitor Block Diagram Figure 6-3 +73 Volt Supply Circuit ............ Figure 6-4 — Motorola Monitor Vertical Drive Waveform Figure 6-5 | Motorola Monitor Video Amplifiers and Output Circuit . Figure 6-6 | Motorola Monitor Horizontal Deflection Circuit .... Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms Figure 6-8 | Motorola Monitor Horizontal Output Circuit .. Figure 6-9 | Motorola Monitor Sync Circuit Figure 6-10 Motorola Monitor Vertical Oscillator Circuit . Figure 6-11 Motorola Monitor Spot Killer Circuit ...... Figure 6-12 Motorola Monitor Blanking Amplifier Circuit Figure 6-13 Motorola Monitor Chassis Rear View—Component Location Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View
LIST OF ILLUSTRATIONS
Figure 6-15 Figure 6-16 Figure 6-17 Figure 6-18 Figure 6-19 Figure 6-20 Figure 6-27 Motorola Monitor Schematic Diagram Motorola Monitor Circuit Board Detail—Component Location TEC Monitor Chassis, Rear View . TEC Monitor Chassis, Top View .. TEC Monitor Printed Circuit Board, Top View .. TEC Monitor Schematic Diagram . TEC Monitor Wiring Diagram
LIST OF TABLES
vi Table 1-1 Table 1-2 Table 4-1 Table 6-1 Table 6-2 Table 6-3 Self-Test Procedure ... Operator Options 6 Address Map .. 42 Motorola Monitor Electrical Specifications . 73 Motorola Monitor Replacement Part Numbers 86 TEC Monitor Replacement Part Numbers ........ 0.00000 eevee evens 91
A. INTRODUCTION Ultra Tank® is a one- or two-player tank battle game developed by Kee Games. The game is contained in an upright cabinet which is illustrated with brightly colored graphics to enhance player appeal. A 19-inch black-and-white TV monitor is mounted in the top front of the cabinet, with the viewing screen tilted slightly from a vertical position.
LOCATION SETUP
A player control panel is mounted directly below the TV monitor viewing screen on the front of the game cabinet. The controls consist of two sets of levers or joysticks, with a pushbutton switch mounted on top of the right joystick of each set. The control panel also includes a START button for each player, and three option toggle switches for one or both players to select from.
The player's objective is to shoot the opponent's tank while maneuvering his or her own tank to avoid oncoming shells. Players also have to contend with barriers, mines, and boundaries, which are stationary. Ahit made on an opponent's tank adds one point toa player's score. If a player's tank runs into a mine, one point is added to the opponent's score. Each player’s score is displayed continuously on the TV screen.
Players have several combinations of options available. The three toggle switches (already mentioned) on the player control pane! dictate these options. They are: INVISIBLE TANKS dy VISIBLE TANKS OPEN BATTLEFIELD
BARRIERS AND MINES pushbutton, located on the right joystick, controls the firing of shells from that tank. A player may fire one shell, or two consecutive shells, but may not fire again until one or both of these shells explode. Shells travel in straight lines, or can be “guided” by using the joystick controls.
By selecting the GUIDED SHELLS option, a player can “guide” a shell with the joystick controls in the same manner in which the direction of a tank is controlled. A detailed diagram of the joystick controls and corresponding tank directions is displayed in the center of the control panel on each Ultra Tank game.
The REBOUNDING SHELLS option causes shells to explode after rebounding off any four walls, barriers, stationary objects, or when an opponent tank is hit. The shells explode upon impact with a fifth contact. When this option is in play, the shells cannot be “guided” with the joystick controls. (Other game options are described in Chapter 2.)
REBOUNDING SHELLS
GUIDED SHELLS
Players may select any combination of these options. The options can be changed during game play. A more detailed description of game play is given in Chapter 2.
Play begins after the proper amount of coins have been inserted into the coin mechanism, and one or both START buttons are activated. Players have eight seconds to press both START buttons for a two-player game. After eight seconds, if the second START button has not been pressed, Ultra Tank will start by itself as a one-player game, with one tank controlled by the computer.
As game play begins, the timer (located in the top middle of the viewing screen) begins counting down from 99. One of four optional times, previously set for game length determines the speed of this countdown. See Table 1-2 for specifics on various game lengths and operator options. Play ends when the game time has run out (reached 0).
Tanks can be made to go forward, backward, or to turn, but there is only one speed. The player's A gunshot sound is produced whenever a shell is fired, and a more pronounced explosion sound is produced whenever a shell explodes. An explosion sound is also produced whenever a tank runs over a mine. There is no limit to the number of shells that can be fired during a game.
B. GAME INSPECTION
Your new Ultra Tank game is manufactured by Kee Games with the intent of being ready to play immediately upon removal from the shipping carton. Your cooperation is needed to supply the final touch of quality control. Please follow the procedures below to ensure that your game is in perfect condition.
1, Examine all external parts of the game cabinet for dents, chips, or broken parts.
- After determining that the game has been received in good condition, unlock and open the rear ac-
cess door. Carefully inspect the exterior and verify that:
¢ All plug-in connectors are firmly seated. © The fuses are all seated in their holders.
- No harness wires are disconnected.
© No loose foreign objects are present, especially metal objects that could cause electrical problems.
Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speaker, the player controls, and the TV monitor chassis.
C. LOCATION OF SERIAL NUMBER The serial number for Ultra Tank is located on a metallic label in the upper left-hand corner in back of the game cabinet. This serial number also appears in the corner (common to both edge connectors) on the back of the PCB, inside the game cabinet. See inside front cover of this manual.
D. INSTALLATION REQUIREMENTS Power Requirements and Line Voltage Selection Ultra Tank is shipped for operation at 110 VAC, 60 Hz. Power consumption is approximately 150 watts. However, if your local current is not 110 volts, follow this procedure. You must select one of four connectors at the power supply and plug it into the voltage selection socket. Figure 1-1 shows the four connectors, with one of them plugged in. The plugs are identified by wire color as listed in this figure. Note that there are two basic operating voltages—110 VAC, 60 Hz and 220 VAC, 50 Hz, with provisions for low line voltage in each case. To insure proper operation, measure line voltage. If voltage is consistently
LINE VOLTAGE 95 VAC VOLTAGE-CHANGING PLUG WIRE COLOR BLACK ORANGE installed at factor 110 VAC
210 VAC 220 VAC
ON/OFF AND Cc INTERLOCK SWITCH
Co be 3Amp, 250 v. Slow - blow
8 Amp, 125V, ‘Voltage - Change Plugs Fast-Blow
2.5 Amp.125 V. Slow —blow
Figure 1-1 Location of Voltage-Changing Plugs on the Power Supply
below 100 V (for 110 VAC lines) or below 210 V (for 220 VAC lines), use the low-voltage connections.
Temperature Range Location and storage should not be below 0 degrees Celsius (32 degrees Fahrenheit), and no higher than 49 degrees Celsius (120 degrees Fahrenheit).
Humidity Range Relative humidity for location or storage should be no more than 95%.
Location Space Requirements Vertical Clearance—155 centimeters (61-1/4 inches) Width Clearance—71 centimeters (28 inches) Depth Clearance—86 centimeters (34 inches)
Type of Power Cord Kee Games has added a strain relief power cord to Ultra Tank. The advantage of this type of power cord is that, if pulled accidentally, the strain relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and pre: ents the cord from pulling the wires out of the harness connector.
E. INTERLOCK AND POWER ON/OFF SWITCHES
To minimize the hazard of electrical shock while you are working inside the game cabinet, an interlock switch has been installed at the rear access door. This switch removes all power from the game while the access door is open. To help you conserve energy, a power on/off switch has been installed on the game so that it can be turned off during closed periods. Refer to Figure 1-2 for switch locations.
Please check for proper operation of the rear access door interlock switch by performing the following steps:
- Unlock and open the rear access door.
- Plug the AC power cord into a 110-volt source. (If the voltage is consistently less than 110 VAC, make sure that you change the voltage plug to the black plug.)
- Set the power on/off switch to the on position by flipping the toggle switch toward the front of the game cabinet.
- Close the rear access door. Within approximately 30 seconds the TV monitor should display a picture.
- Slowly open the rear access door until the TV monitor picture disappears. The TV monitor picture should disappear when the rear access door is opened less than one inch from the top.
- If the results of Step 5 are satisfactory, the interlock switch is operating properly. If the picture does not disappear as described, check to see if the switch is broken from its mounting or stuck in the on position.
- Close and lock the rear access door.
F. SELF-TEST PROCEDURE Ultra Tank will test itself and provide data to demonstrate that the game’s circuitry and controls are working properly. The self-test procedure uses the TV monitor and the speakers; no additional equipment is required. We suggest that you run the self-test procedure each time the coin box is emptied. See Table 1-1 for specifics on the self-test procedure.
To start the self-test mode over from the beginning, set the self-test switch to off, then again to the on position. This will return the self-test mode to Step 1, and can be done at any time during the procedure.
G. OPERATOR OPTIONS Options of the Ultra Tank game offer maximum player appeal for each game location. These options are listed in Table 1-2. They are preset for a certain game structure during production. To determine how the switches have been set for your game, compare the TV monitor viewing screen during the attract mode with the information in Table 1-2.
To change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedure:
- Unplug the game. Unlock and open the rear access door.
- Locate the radio frequency (RF) shield assembly immediately inside the cabinet on the right. (It is an aluminum box with small holes.) On one end of the box is a printed circuit board with an edge connector coming from the edge of the board.
VOLUME CONTROL INTERLOCK SWITCH
Figure 1-2 Location of On/Off, Interlock, Self-Test, and Volume Control Switches
- Remove the five pan-head Phillips screws from each of the long sides (total of ten screws) of the RF shield assembly.
. Carefully remove the PCB from the RF shield assembly.
wn
Table 1-1 Self-Test Procedure
Test Instruction
Results if Test Passes Results if Test Fails
1 Unlock and open coin door. Set self-test switch (located inside the coin door, nearest the hinge), to the on position. TV monitor screen will display the words:
RAM OK = ROM OK
Beneath these words, in the middle of the screen, a 1, 2, 3, or 4 will appear. This number corresponds to the time option set for game length. (Refer to Table 1-2 for game length options.) Several complete sets of alphanumerics will appear on the bottom of the screen (A through Z, and 0 through 9.) Also, both START buttons will be lit. TV monitor screen will display the words: RAM OK BAD ROMA or BAD RAM ROM OK or BAD RAM BAD ROM D The letters following the BAD ROM correspond to the malfunctioning chip. (Chips are represented by the letters A through O.)
2 Activate all joystick levers, firing buttons, START switches, and option switches individually. Trip right and left coin switch wires.
Close contacts of coin door slam switch. Anelectronic clicking sound occurs each time a lever or switch is activated, and again when the switch is released.
Same electronic clicking sound occurs each time a coin switch wire is tripped and released. Electronic clicking sound occurs each time slam switch contacts are closed and released. No clicking sound will indicate a stuck or broken switch, or an open or shorted harness.
Table 1-2 Operator Options
Option 1 2
Extended Play | OFF OFF OFF ON ON OFF ON ON Switch Settings 3 4 5 6 7 8 Result
Extended play (1 of regular game length) granted for score of: 75 Points 50 Points 25 Points No Extended Play Allowed
Game Length TV monitor during self-test: 60 Seconds “i 90 Seconds “2 120 Seconds 03" 150 Seconds “qr
Game Cost ON ON ON OFF OFF ON OFF OFF
ON ON OFF ON ON OFF OFF OFF [Not used.] One Coin Per Player Two Players Per Coin Two Coins Per Player
r | @ caution & | | To avoid damaging capacitors | | on back of this PCB, move 14" | toward arrows. Then pull to- | ! ward you. | | Assy. No, __ I a ob tooo
ROW 2
ROW 1
,
ROW 1 if I
ROW 2 oboo ° fe) 123456789103
Figure 1-3 Caution Label on Game PCB
- Set the switches for the desired options, as shown 7. Plug in the game and verify option functions by in Table 1-2. playing it.
- Reinstall the PCB following Steps 1 through 4 in reverse order. Do not force or bend the printed H. VOLUME CONTROL circuit board. Before reinstalling, always inspect {f volume is incorrect for your location, open the the printed circuit board for damage. Close and coin door and adjust the volume control. See Figure lock the rear access door. 1-2 for location of volume control.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
There are three modes of operation: attract (power applied), ready-to-play (coins accepted), and play (one or both START buttons activated).
A. ATTRACT MODE (See Figure 2-1) The attract mode begins when power is applied to the game and ends when the proper amount of coins are accepted by the coin mechanism. The appropriate coin and extended play messages appear in the middle of the screen, according to the options which have been selected. All controls and sounds are inactive during this mode.
Figure 2-1 Attract Mode
The TV monitor viewing screen displays different game play situations, while the tanks continue to stage battles. These battles enable prospective players to see actual game play characteristics. Scores from the previous game appear at the top of the viewing screen.
B. READY-TO-PLAY MODE (See Figure 2-2) When the correct amount of coins clear the coin mechanism, the ready-to-play mode is initiated. During this mode:
Figure 2-2 Ready-To-Play Mode
- The messages SELECT OPTIONS and PRESS START appear on the screen.
- Messages indicating selected options appear on the screen. ¢ The word ROBOT appears under both scores.
¢ The coin message disappears. ¢ The number of points required for extended play is displayed. ¢ Both START buttons flash on and off.
Players have the opportunity to select the options they desire—now or anytime during game play.
By selecting the BARRIERS AND MINES option, players must maneuver their tanks around the obstacles, rather than having an empty playfield (as in the OPEN BATTLEFIELD situation) to compete in. A collision with a barrier prohibits a tank from travelling onward, and the player must maneuver around it. A collision with a mine, however, adds one point to the opponent's score. The mine then disappears for the remainder of the game. All new mines will be restored during a game only if a player changes the toggle switch from BARRIERS AND MINES to OPEN BATTLEFIELD.
The INVISIBLE TANKS option adds an interesting and unique aspect to the game. When this option is selected, both tanks (whether in a one- or two- player game) are invisible for the duration of the game, except when a shell is fired. When a tank fires a shell, it becomes visible only until that shell explodes. Upon impact of the shell, the tank becomes invisible again.
The skill level becomes more challenging during the INVISIBLE TANKS mode if the BARRIERS AND MINES option is selected. A player must maneuver his or her invisible tank around the playfield, risking collisions with mines, and thereby adding points to the opponent's score. When a tank runs into a barrier or mine it becomes briefly visible.
The more familiar players become with the location of the mines and barriers in the playfield, the more skillful they will become in movement and point scoring.
The REBOUNDING SHELLS and GUIDED SHELLS options also add interesting versions to your Ultra Tank game. As mentioned in the introduction (Chapter 1) REBOUNDING SHELLS must bounce off four objects before exploding upon impact with a fifth object. The shells will destroy an opponent's tank, but will pass through the tank from which they were shot.
GUIDED SHELLS can be steered or guided while in flight by using the joystick controls. When one option is in play (i.e, REBOUNDING SHELLS or GUIDED SHELLS), the other option is automatically cancelled out.
C. PLAY MODE (See Figure 2-3) The play mode begins when one or both START buttons are pressed. Pressing a START button removes the word ROBOT from the corresponding score and lights that button. If credit remains, the other button continues to flash. If no credit remains, the button becomes dark. An eight-second delay oc-
Figure 2-3. Play Mode curs when one START button is pressed. During this time the number of SECONDS TO PLAY appear on the screen. If the other START button is pressed within eight seconds (assuming sufficient credit), the game starts as a two-player game. If the other START button is not pressed within eight seconds, the game begins as a single-player game.
As play begins, the game timer (located at the top middle of the viewing screen) counts down from 99. This count is always the same, regardless of the operator game time setting. (Refer to Table 1-2 for game time options.)
Each tank commences action from a home position. If barriers and mines are in the playfield, the tanks start from opposite ends of the screen and are situated behind barriers directly facing each other. If the playfield is “open,” the right tank begins from the bottom right corner, and the left tank begins from the upper left corner.
When the game timer reaches 0, the scores are checked for possible extended play. If required, the timer is restarted at 33, meaning one-third more game time than a regular, paid-for game. When it again reaches 0, all action freezes. Accumulated scores remain at the top of the screen. For a few seconds, the words GAME OVER appear on the screen along with an extended-play message. Eventually the game returns to the attract mode. If one tank was robotcontrolled, the word ROBOT will continue to be displayed under that score.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Due to its solid-state electronic circuitry, this Kee Games unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended
MAINTENANCE to cover most servicing situations that may be
encountered at the game site, The procedures given
AND are in sufficient detail to be understood by a person
with moderate technica! background.
AD JIUSTMENT NOTE
If reading through this manual does not lead to solving a specific maintenance problem, you can reach Atari’s Customer Service Department by telephone Monday through Friday, from 7:30 a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900; from the remaining 47 states call (800) 538-6892 (tollfree).
If you are interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator's Handbook, manual number TM-043. This book is available from Atari, Inc., Attn. Customer Service Department, 2175 Martin Avenue, Santa Clara, CA 95650 for $5 each, or from your distributor.
. CLEANIN The exteriors of game cabinets and plex panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the plex panels because any dust can scratch the surface and result in fogging the plastic.
B. COIN MECHANISM Components On Coin Door Figure 3-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. But during the ready-to-play mode when the LED is lit, and during the play mode (and also when AC power to the game has been turned off),the lock-out coil is de-energized, causing the lock-out wires to move out far enough to divert coins over to the return chute.
Coin Lock-out LAMP HOLDER Coil Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.
Also shown in the photograph is a slam switch assembly. It has been included to discourage any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or, ifnecessary, each coin mechanism can be entirely removed from the door merely by pushing down onarelease lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3.
Figure 3-1 Coin Door Assembly Figure 3-2 Hinging Open the Magnet Gate Assembly
Figure 3-3 Removal of Coin Mechanism
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.
Figure 3-4 shows the surfaces to clean inside the coin
(Clean both surfaces where coin enters the mechanism, as well as the magnet) Figure 3-4 Surfaces to Clean Inside the Coin Mechanism mechanism. These include the inside surface of the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.
if coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a ¥%-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 3-5), Removing the plate will provide access to the entire channel.
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Figure 3-5 Removal of Plate Covering Rear of Coin Slot
Lubrication. Do not apply lubrication to the coin mechanisms. The only points that may need !ubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism.Figure3-6 shows this lubrication point.
Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 3-7. Use extreme care when handling or touching these wires.
Manually hoid down rejection button and apply one drop here
Lock-out Wire
Figure 3-6 Close-Up View of Lubrication Point
Three problems can occur with trip wires—they can be too long, too short, or become loosened and fall off.
Correctly adjusted trip wire
Figure 3-7 Detail View of Coin Switch and Trip Wire CRIMP TOGETHER MOUNTING STUD AT 2 ARROWS SHOWN
Figure 3-8 Securing the Coin Switch Trip Wire
With a wire that is too long, you may have a problem of it catching on the opening in the cash box as a coin is accepted. You can cut off the end of the wire in small increments, making sure it still extends slightly through the ‘’V” of the coin chute.
If the trip wire is too short (either by wrong adjustment or by being cut off too much), coins may slip by the wire without tripping it, and no credits will be given, The solution is to carefully bend and straighten out the wire to lengthen it. If you cannot straighten it sufficiently, contact your distributor to order another trip wire.
If the wire is loose and falls off its mounting stud, it will also cause no credits to be given. Secure the wire by crimping together both ends of the brasscolored mounting stud with a pair of pliers (see Fi ure 3-8). If you should ever need to remove the trip wire, the two halves of the mounting stud can be separated with a small screwdriver.
Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure3-9 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These
ITEM IDENTIFICATIONS. 1 Kicker and Separator Screws 2 Washers: 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly 8 “C” washer 9 Rail 10 Gate Assembly 12 Cradle Assembly
Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 in Rel Kicker and separator Coin: Relesse:Lever 1, Set the acceptor with the back of the unit facing you in the test position.
- Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
- Insert several test coins (both old and new) and note that some are returned by striking the separator.
- Loosen the separator screw and move the separator a siight amount to the left. Lightly retighten the screw.
- Insert the test coins again and. if some are still returned, repeat Step 4 until all the coins are accepted.
- Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
- Insert the test coins and note that some are returned,
- Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
- Be sure that both screws are tight after the adjustments have been made.
Magnet gate
- Set the acceptor with the front of the unit facing you in the test position.
- Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
- With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
- Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
- Fix the magnet gate adjusting screw in this position with a drop of glue.
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- Replace the transfer cradle and the undersize lever.
- To be certain the coin mechanism is compietely free of any residue, place the mechanism in boiling water for several minutes, Carefully remove it and let it air-dry completely before reinstalling in the door.
Figure 3-9 Adjustments on Coin Mechanism
adjustments should only be done by someone who has experience in servicing coin mechanisms and who understands their operation.
General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
C. FUSE REPLACEMENT Ultra Tank contains seven fuses, five on the power supply assembly in the lower part of the cabinet and two on the TV monitor assembly. All fuses are easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows:
TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick-blow, 250 volts Power Supply: Fuses F1 and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4—3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp fast-blow, 125 volts
D. TV MONITOR REMOVAL (Refer to Figure 3-10) Remove three screws (button-head socket cap #10-32) at the top edge of the cabinet and remove the Plexigias‘retainer. Then remove the Plexiglas screen and the cardboard bezel. Be sure to reconnect the ground wire when removing the bezel. At the back of the cabinet, remove the rear door which is secured by four wood screws. Remove the four carriage bolts which secure the monitor to the TV shelf assembly. Disconnect the TV monitor harness and slide the monitor out through the front of the cabinet. E. TV MONITOR ADJUSTMENTS
The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustment.
The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 3-11 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC. When making adjustments, follow these general guidelines: BRITE (Brightness) —Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up. CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred. HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture. VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture. F. LED START SWITCH AND OPTION SWITCH REPLACEMENT (See Figure 3-12) Unlock and open the coin door. Disconnect the control panel cable connector and remove the four
PLEXIGLAS RETAINE R
CARRIAGE BOLTS (4)
PLEXIGLAS SCREEN BUTTON-HEAD SCREWS
Figure 3-10 TV Monitor Removal
conrassr | TC yert. UC VERT. LIN.
BRIGHT? HEIGHT
woniz Hou) \_vert HOLD
TEC MODEL TM- 600/623 ‘contaasr woRIZ. osc. 2 FUSES- REMOVE. COVER To REPLACE (both 0.8.8 quick blow ‘BRIGHTNESS, Focus
MOTOROLA MODEL M5000/M7000
Figure 3-11
wing nuts (two bottom and two top) securing the control panel. Note that a ground wire is secured under one of the lower wing nuts. The LED switches are accessible when the panel has been removed. Remove the wires from the suspected switch and turn the switch counterclockwise while holding the cone-shaped nut on the outside of the game cabinet. Install a new switch using the reverse procedures. Reconnect the harness wires. When reinstalling the panel, be sure to secure the ground wire as before.
The option (toggle) switches are also accessible when the control panel has been removed. Follow the same procedures as those described for removing the LED switches. Be certain to secure the ground wire when reinstalling the control panel. Locations of Adjustments on TV Chassis
G. JOYSTICK REPAIR (See Figure 3-13) Remove the control panel by following the procedures described in Section F (LED START SWITCH AND OPTION SWITCH REPLACEMENT). The two joysticks without firing buttons (left lever of each set) are accessible for servicing by removing nine screws at the base of the joystick assembly.
The two joysticks with firing buttons (right lever of each set) are also accessible for servicing by removing nine screws. However, to remove the rod and firing button, it is necessary to break the plastic disc which is glued to the rod at the base of the assembly. After breaking the disc, remove the hex nut witha nut driver. Refer to Figure 3-13 for location of assembly parts.
START SWITCH
Unlock and open the Coin Door.
Disconnect control panel cable connector. then remove two carriage bolts.
Remove wires from suspected switch.
counterclockwise while holding -d ut on outside of game cabinet, install new switch using reverse procedure.
Reconnect harness wires, 5.
é OPTION SWITCH
Unlock and open the Coin oor.
Disconnect contro! panei cable connector: then remove two carriage bolts.
Remove wires from suspected switch,
. Turn switch counterclockwise while holding cone-shaped rut on outside of game cabinet,
Install new switch using reverse procedure.
Reconnect harness wires.
OPTION SWITCH
Figure 3-12 LED START Switch and Option Switch Replacement
JOYSTICK WITHOUT FIRING BUTTON
JOYSTICK WITH FIRING BUTTON REMOVE NINE SCREWS FROM ASSEMBLY BASE
ZN | [zzz 77777
HEX NUT
FIRING BUTTON
SWITCH
Figure 3-13 Joystick Removal
A. GENERAL INFORMATION The PCB block diagram in Figure 4-1 shows the major controls, circuits and outputs of the game. Figure 4-2 is a block diagram of the Ultra Tank game.
The game’s television monitor is a self-contained transistorized unit. The composite video signal sent to the monitor differs in many respects from the signal derived from commercial TV broadcasts. The picture appearing on the screen, therefore, is unlike that of a home TV set and the monitor does not produce any sound. See Chapter 6 for a schematic diagram of the TV monitor.
The game's composite video signal produces only four video levels instead of the continuous shades of grey seen on a home TV screen. The background of the picture is light grey video. Game objects use two video levels. The white level is for one tank, its shell (missile), and the barriers and mines. The black level is used for the other tank and its shell.
On the game PCB schematic diagram, the symbol “P” (appearing at various inputs of intergrated circuit devices) indicates a connection of +5 volts DC through a pullup resistor (see Figure 4-3). For easy reference, the game PCBis divided into grid sections. Along the short side of the board, these sections are identified by letters A through R (skipping letters G, |, O and Q because they may be easily confused with the numbers 6, 1, and 0 respectively). Along the long side of the board, the numbers 1 through 12 are used. For example, sheet 4 of Figure 4-3 illustrates the microprocessor C3 at the left side of the drawing. The microprocessor is found at coordinates C and 3 on the PCB.
B. POWER SUPPLIES (Upper Right of Schematic Sheet 1, Figure 4-3) Three voltages are used on the Ultra Tank PCB: voltage-regulated +5 volts DC, unregulated +10 volts DC, and unregulated +20 volts DC. The voltage regulated +5 volts DC provides Vcc for most of the PCB's integrated circuits. Unregulated +10 volts DC provides V+ for the LM339 comparators at the joy/ stick inputs. Unregulated +20 volts DC provides V+ for the TDA-1004 audio amplifier.
C. CRYSTAL OSCILLATOR AND TV SYNC COUNTDOWN CHAINS (Upper Left of Schematic Sheet 1) A 12.096-MHz crystal oscillator generates the basic clock frequency that is divided down to produce TV synchronization signals. The signals are used to produce the TV monitor raster, consisting of 262 horizontal lines at a horizontal frequency of 15,750 Hz (256H). Synchronized with line 224 is a vertical blanking pulse that occurs for the duration of 38 more horizontal scans, resulting in the total number of 262 lines per picture frame.
Other than being used for the TV raster, the TV timing signals are used in the motion circuits, the alphanumerics display circuit, the microcomputer clock, and in various other places on the PCB.
D. MICROCOMPUTER The microcomputer is the control center for the circuitry that makes up the game action. The microprocessing unit (MPU) sends out addresses on its address bus and accepts from, or outputs data onto the data bus. The Address Decoder receives the address, translates the address code, and enables the circuitry called by the MPU. When the MPUis reset by receiving a low, and then a high on its RESET line, its outputs address the program memory to put data onto the data bus. The MPU reads this data and uses it to address the main program.
The main program instructs the MPU to execute operations, and instructs at which address to execute them. This controls the flow of data on the bus and “reads” inputs and “writes” to outputs. Data may flow into the MPU from program memory, randomaccess memory (RAM), or from tri-state drivers from the input and option switches.
Data may flow out of the MPU to the zero-page RAM, or to the digital-to-analog latch E6. The 14 least significant bits of the 16 address lines are labeled BA (buffered address). The 8 data lines are labeled D for data inputs to the MPU and DBUS (buffered data) for data outputs from the MPU.
E. MICROCOMPUTER WATCHDOG (Top Left of Sheet 4) The watchdog circuit is connected to the RES input of the MPU. This circuit prevents the microcomputer from going into a program loop. Notice the 128V and TIMER RESET inputs to the watchdog counter E5. The 128V is equal to one full vertical scan of one frame of video (monitor picture). This input signal makes the watchdog counter count. If the counter counts to 8 without being reset, the counter outputs a low to the MPU RES input. This tells the MPU that something is wrong, and the MPU resets itself to the beginning of the program. To be less technical, when the MPU gets reset by the watchdog, the results are the same as turning the game power off, and then on. All game play stops, and credits are lost.
Now, back to the second watchdog counter E5 input mentioned above—TIMER RESET. This signal is the output of the Address Decoder (B2, E11, M10, and N10).
Take a look at the Address Map of Table 4-1. The center column of the Address Map is titled SIGNAL NAME. Look down this column and find the signal TIMER RESET. The microcomputer is programmed to send out the address, listed in the Address column to the left of the signal TIMER RESET, once in each frame. This address results in a TIMER RESET signal that resets the watchdog counter to zero. Therefore, if the microcomputer is operating properly, the watchdog should never reset the MPU.
F. MOTION GENERATOR (All of Schematic Sheet 2) The motion generator generates the video for the tanks and shells, which are the only moving objects of the Ultra Tank game. The tank/shell picture ROM (consisting of ROMs K6, L6, M6, and N6, fora memory size of 1024 x 15) is programmed by Kee Games to provide fifteen bits of data for each of the sixteen lines of each of the thirty-two different states of rotation of a tank. The tank/shell picture ROM also contains pictures for large (tank) and small (shell) explosions, and a shell picture.
The microcomputer RAM provides three words (bytes) of data for the display of each tank/shell picture. The first byte determines the vertical location of the tank/shell, the second determines the proper rotation picture of the tank, and the third determines the horizontal location of the tank/shell. The accessing of these bytes of RAM data is done during the horizontal blanking period (256H).
Vertical position data is received by Vertical Line Comparator P6 and R5. For example, study the data code fora tank to be displayed beginning on line 120. The RAM byte data code of 01111000 would be loaded into the comparator. When the vertical line comparator reaches the count of 01111000, and 8H, 64H, and 256H are all high, the conditions are met for alow at the output of NAND gate R6 (pin 6). One 1 clock pulse later, a low appears at the output of NAND gate R6 (pin 8).
The RAM byte data code that controls tank rotation is capable of addressing any of sixty-four different pictures. The six bits of data code necessary to do this (PRAM 2 through PRAM 7) are applied directly to the address input of the tank/shell picture ROM. The least significant address lines applied to the tank/shell picture ROM (inputs AO through A3) complement the rotation data code by determining which of the sixteen lines of the tank is being described by the ROM data output. When 1 is high the video data output (VID 0 through VID 15) from the tank picture ROM is timed with load vertical pulse LOAD x. This signal enables shift register N7 and N8 (M7 and M8, L7 and L8, K7 and K8) to load the video data from the tank picture ROM.
In review, the motion generator has received a RAM data code for where the car is to be displayed vertically and a RAM data code for the proper picture of the tank/shell. The final instruction needed is for the horizontal! placement of the tank/shell. The RAM byte that determines this placement is received by the tank/shell horizontal location counter.
The tank and shell horizontal location counter P5 and P4 (N5 and N4, M5 and M4, or L5 and L4) is loaded each horizontal line by a load horizontal pulse LOAD x. The counter is preset to a given count by the RAM data code (DMA 0 through DMA 7) during horizontal blanking. At the end of horizontal blanking, 256H goes and the counter is enabled to begin counting up at a clock rate of 6 MHz. When the counter reaches its final count, the CO output (pin 15) enables the shift registers, allowing the 15 bits to be shifted out as OBJECT x (pin 9).
G. PLAYFIELD GENERATOR (Lower Left of Schematic Sheet 1) The Playfield Generator generates both the playfield and all alphanumeric video for the TV monitor display. All this information is stored in the playfield ROM (consisting of ROMs H6 and J6).
The TV monitor picture is made up of 32 horizontal by 28 vertical grid sections. For each grid section the microcomputer RAM has a byte (one byte equals eight bits). These grid sections are represented by the data signals DO through D7.
During the rising edge of 2, the playfield data from Playfield Memory (H2-R2) is transferred to latches K4 and KS (see sheet 3). RAM data DO through D7 now become data signals DMAQ through DMA7. These data signals are the address inputs to the Playfield ROM (consisting of ROMs H6 and J6).
The Playfield ROM is programmed by Kee Games to provide eight bits of data for each of 512 addresses. The least significant address inputs are from vertical synchronization 1V, 2V, and 4V, and select one of eight scan lines. The most significant address inputs are DMAO through DMAS from the playfield RAM, and select one oi 64 8 by 8 pictures.
The top of Figure 4-4 illustrates the letter “C’’ as it would be “traced” in one grid section on the TV monitor display. The RAM provides one six-bit address to the Playfield ROM for the letter, while vertical synchronization 1V,2V, and 4V complements the RAM address for each of the horizontal scan lines. The bottom of Figure 4-4 illustrates the serial output of shift register F5 for each of the eight horizontal scan lines. Binary counter H8 latches data bits DMA5, DMA6, and DMA7, from the microcomputer RAM.
Figure 4-1 Ultra Tank PCB Block Diagram ADDRESS
DECODER
DATA
PROGRAM
ADOREST s—i_) ReADWaire
ENABLE
10. v MONITOR
TANK/SHELL
TANK & SHELL
PICTURE VIDEO:
GENERATOR
MEMORY OM
MANUAL contro. [aa INTERFACE
- SHELL FIRE EXPLOSION 10 GeNeRaTon GENERATOR | > SPEAKERS
ac SOURCE w WORIZONTAL OEFLECTION betatti INTENSITY mall mncUrTRY ‘Sueur KEYING
VERTICAL DEFLECTION <)
composite VIDEO
PLAYER sovsTicKs
Lerr PLAYER, FIRE BUTTON
RIGHT PLAYER ‘camer sovsricks PRINTED CIRCUIT con BOARD MECHANISM SPEAKERS
RIGHT PLAYER FIRE BUTTON
REBOUNDING SHELLS.
SELF-TEST SWITCH
Figure 4-2 Game Block Diagram
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
our Le ‘i BOTL & CeBS, J sey
T°? Devens tov [5 conzesEL®
e8vAt ~= s2ov (unRes)
2evac NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the Specitic written permesion of Atari ine. Sunnyvale asver Calorcia This drawing is only conditionally issued. and
| L | 1 | neither | receipt nor possession thereat confers or translers |
fry nght nor hcense to use, the subject matter of Ine rawing of any design or Techncal information shown thereon. norany ng to reproduce ths drawing or any part thereat except or manulacture by vendors of Alt near= porated and tor manulacture under the corporation si {en icanse,no ight toreproduce!vsdrawingis granted ot the subject matier erect unless by writen agreement wath oF wntten permission ram ine corporation,
tv
Boe 535 sey
. is SEs oP i cones > wo pel ie] ware Di te _ 7 oa Ba le © off _ = se 3 aes eo 8 oe
| 38 | a | of | ms |
Fae 10 Ja3, ° 3] <3 te = peawr—2ip 5 af = : a Jo ToAs 3 voter; 182
HBLANE C] come vives VBLANE 8 Reyne Vy] vice
| Je | ‘3 | Vewne | er" | Dis | PROM |
roan : eee _ ~O2 = ROM opseete 2 ZG] conrevie
NC. PLAYEIELD @ DOWER
s Saye ai opsect3—H22
12 9 pramr—2lo foal? fears uf S84. le 2, Tema 2 8 3[53)¢$——_ Tp obveRTe
Figure 4-3 Ultra Tank PCB Schematic Diagram Sheet 1 of 6
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari, Ine. Sunnyvale California, This drawing 18 only condiianally issued. and neither cecerpt nor possession thereo! canters or transfers, {any right in, oF license to use. the subject matter of the drawing or any design or technical inlormation shown tereon. norany right fo reproduce this drawing ot any part ‘thereot. except for manulacture by vendors of Atari Incorporated and for manulacture uncer the corporation switten license. no right to reproduce this drawingis granted or ‘the subject matter thereo! unless by writen agieement wilh oF wntten permission team the corporation
sev sev
| coe | hee | pears is | hs | |
| rar | “ha | Pawn | Tha! |, optus | |
| TR | ee | | pea | Posnuny | |
| ‘Dwar ——- ee | PRAMS | riled | f— | woe |
| Sra. | * | Beane | aft | he |
| BeN | ls | PRAMS — | ae | ee) |
| . | eee | = | vod | |
| v | rs | 7 |
ww wpe
caf pe
| eo | calit | ba | ||||
| Cre | tlea | RS | * | |||
| pane | ——t}e | °* | ahs | fof | wer | |
| ae | the | ef | — | Zee | Scat | yn |
| ke | fn | si | oi @ | aad | ||
| ore | eee | Ze | zx, 6 | |||
| eB | Joe | fe | 388 | oe | ||
| ey | Bas | & | PEs |
le
Sat f of®— won, as 5 li
ha me} le 108 we of vio
| Fixe | ef | yore |
Ing & oat 2— wis aes a sae m8 Ean me Spe
fas |B
“jae 2 reeeicy ee se anos & cm ape sph
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
osy a _|slsls ape am
te
sar
te
x
x
F . 2 iret we) oa | owe z 2 ao-ro14 | 50-7018 av bi_bo| bio TE Pe NE he
3 ea 2 ie e &
cu
‘e
i
=O} VERSION
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari. inc. Sunnyvale California. This drawing Is only concitionally issued. and netther receipt nor possession theveat conters or wansters any right «n, oF license 10 use. tne subject matter of the ‘drawing or any design oF technical information shown lnereon naeany right to reproduce this drawing or any part Inereot except lor manulacture by vendors of Atat incor porates and for manulaciure unger the corporation writ ten license. no right lo reproduce thisarawing's granted oF tre subject matter thereo! unless by witten agreement with or written permission trom the corporation
peau? ——2}2> i . PRAM hap,
segeess s2ei5iis aKe.
eke Fags :
upste 2 er" [ls sale eo aie . ot be aoe 4 Toa fie 4 be baat “ apse L a 7 os S ——2ss + i a Sie re 7 Sat b ope 4 a be
ema Wwe lis bs
os | a9 ne
a? ~ Db? @ oft oe © altos 4 \ 0 oft be
MEMOKY
a J =O VERSION
Figure 4-3 Ultra Tank PCB Schema Sheet 3 of 6 Diagram
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEWING THIS DRAWING: CONFIDENTIAL Regroguction forbidaen without the specific written permission of Alar. Inc. Sunnyvale, Cakforia This drawing is only conditionally issvec. ang ether receipt nar possession thereo! confers or transfers Any right in. or license to use. the subject matter of the Sawing oF any design or technical information shown thereon. narany right to reproduce inisdrawing or any part thereot, except for manulacture by vendors of Alar! Incor porated and fot manutacture under the corporation's writ ten license. ne right to reproduce inisdrawingisgeanled ot the subject malter thereot unless by writlen agreement \with oF wntten permasion trom Ine corporation
WA. E76,
fe | eas —fez ga LeD\ Yeo) wae ~ fa af -
ear ae ge
Figure 4-3 Ultra Tank PCB Schematic Diagram Sheet 4 of 6
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING: CONFIDENTIAL Reproduction forbieden without the Specific wntten permssion of Atar Inc. Sunnyvale. Caifarnia, This dawing "5 ony Conditionally issued. and Rus reithor receipt nor possession theteol confers or transfers An 4 sv nv ugh i. oF hcense to use. the subject matler ofthe eta Granag or any design or technical information shown —- Rie {hereon norany right to reproduces drawingor any oar Poms on +sv free! except for manufacture by vendors of Ala INcOr toe porated and for manufacture under the corporation s wit Ienlicense. ao nght to epraauce this drawing is granted of the subject matier thereot unless by wen agreement vat mstten permission from the corporation,
| Boer | u | a? | i |
| SET | A | is | 9M a |
| al | 2 | t | 7 |
| 3), | ue | 28 | fio |
al, 92
| ———_ | 5 | 3 |! |
| Cc REIT SY | ald | zt |
Teese Ce oo Lae oRsecT2 —134 al,
Suan T RESET
Sy oEeats 4 +8v
SSERESIT ‘ol 3 Reset —
| PUREST) | is | BAR | 2 |
| aeseers — | 12.432 | = | 125 |
BARRIGR BEAD
an +sv ESLOSION 4 4 @ Rese VELNE 7 0 a Re —
| 249 | Test | 1OKS | best |
ens vey Lf >
| a | i | <t | ce |
Veuane 8 READ
= Test
gz
LOK x tsy 4 PL eS ys vee &
| go | OS | xs | asa |
biP-sw|
| Lane & | po | a |
7 e
| LANG! | fot | 4 | ||
| crenita | ft | Lt | 4 | 2 |
| ceo | fe | 2 | ||
| tinea Fope ehh | 7 | ' |
oar
| ime | $s | * | a= | Hog, |
if
| space | f=! | 3 | 1 |
| spare $f oo | }'* | = | |
| = | ox | $35S8S6 | 2 |
| 4 PL | HOLOK | Oe | a2 |
tov = hie
Figure 4-3 Ultra Tank PCB Schematic Diagram Sheet 5 of 6
:
= Lees 09. Etsy Sh os ac ao
we (BO a
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING. CONFIDENTIAL Reproduction forbidden without the specific waitien permission of Atari, Ine. Sunnyvale California. This drawing 1s only conditionally issued. and nether receipt nor possession thereat conlers or ransters fany right in. oF license lo use, the subject matter of the drawing or any design oF echnical information shown thereon. nar any nghl to eeproduce this drawing orany part thereof. except lor manulacture by vendors of Atat incor porated and for manulacture under the corporation s writ {en license. no night to reproduce this drawingis granted oF the subject malier thereo! unless by writen agreement with or writen permission trom the corporation
aupet ae MorToRe~
EXPLOSION. ALS and
SHELL FIRE
SHELL FIReZ
pevea —2|
EXPLOSION
dest
Spore —}
TRS
RE, XPLOSON 6a
ATER — 7 cee lp |e a
| : | tee | au? | [eee | " |
| sm | ew | / | Bye | sHeLe FIRE) |
lee Te 8 Geo acap ut aF o4 aH 2A OM af 40. OF ot I aA
| SS | iste Ponte pis | ete ere pey | aes | ane |
aiea \
- 2 8s ears SHELL FIeEZ
| Ciel | ea | Mean | rete | oye |
on Te
Ic ie IS
Figure 4-3 Ultra Tank PCB Schematic Diagram Sheet 6 of 6
OH 1H 2H 3H 4H 5H 6H 7H ov I 1V| :
s <
| ee
Figure 4-4 Playfield Generator Character Trace This results in the selection of the grey scale (shade) of the character (playfield or alphanumeric) that is to be displayed.
The playfield information from shift register F5, along with the grey scale codes (COLOR1, COLOR2, and NUMERAL), are applied to the input of one-often decoder H9. The resulting decoded output of H9 is the address input to the color (grey scale shading) ROM J10 of the video output circuitry.
H. VIDEO OUTPUT (Lower Right of Schematic Sheet 1)
The video output circuitry receives both the playfield and motion information, selects the proper grey scale shading, and sums the signals with blanking signals. The circuitry then provides a composite video output.
I. ADDRESS MAP
The Address Map for the Ultra Tank game is in Table 4-1. This map shows you the addresses necessary to enable the Ultra Tank circuitries. In the previous section of this chapter an example of the use of the table is given for enabling of the TIMER RESET signal.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Audio Functions X xX Lamp Functions Switch Functions Joystick Functions Collision Functions <<< xx 3 MPU Functions Address A15 Al4 A13 A12 A11 A10 AO9 A08 AO7 A06 ADS AD4 AD3 ADZ2 ADT ADO R/W Table 4-1 Address Map
SIGNAL NAME DESCRIPTION
ROM3 ROM4 W RAM RAM DISPLAY ADD RAM V BLANK READ
TIMER RESET
COLLISION READ COLLISION READ COLLISION READ COLLISION READ COLLISION 1 RESET
COLLISTON 2 RESET
COLLISION 3 RESET COLLISION 4 RESET
WRITE D/A LATCH
THROTTLE READ
COIN READ
COIN READ. COLLISION READ OPTIONS READ OPTIONS READ OPTIONS READ OPTIONS READ
LOCKOUT
LED 1
LED 2
WRITE EXPLOSION FIRE 2
FIRE 1
Read data from Program Memory ROM 3 Read data from Program Memory ROM 4 RAM space transfer to V Blanking RAM tri-static data buffer enable RAM enable Additional RAM enable V BLANK data from D7. Test Sw on D6 Resets MPU watchdog counter
Read White Tank collision from D7 Read Black Tank collision from D7 Read Black Tank shell collision from D7 Read White Tank shell collision from D7 Reset White Tank collision latch Reset Black Tank collision latch Reset Black Tank shell collision latch Reset White Tank shell collision latch
Latch throttle match data DBUSO-DBUS3 Left player left Joystick read from D7 Right player left Joystick read from D7 Left player right Joystick read from D7 Right player right Joystick read from D7
Left player Start read from D7 Right player Start read from D7 Left player Fire Button read from D7 Right player Fire Button read from D7 Left Coin Switch read from D7 Right Coin Switch read from D7 Invisible Switch read from D7 Rebound Switch read from D7 Slam Switch read from D7 Language Option read from D0 and D1 Credit Option read from DO and D1 Game Time Option read from D0 and D1 Extended Time Option read from DO and D1
Coin Mechanism Lockout Coil latched On Coin Lockout Coil (latch cleared) Off Left player Start LED latched On Left player Start LED (latch cleared) Right player Start LED latched ON Right player Start LED (latch cleared)
Explosion audio enable. Data from DBUS0-DBUS 3 Right player shell fire audio enable Right player shell fire audio disable Left player shell fire audio enable Left player shell fire audio disable
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ILLUSTRATED PARTS CATALOG
The purpose of this Chapter is to provide you with the necessary information for ordering replacement parts for the Ultra Tank Game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this list, and the serial number of your Ultra Tank game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
If there are any questions about this list, please contact Atari’s Customer Service Department by telephone Monday through Friday, from 7:30 a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900, from the remaining 47 states call (800) 538-6892 (toll-free).
Your game will include either the Motorola or TEC monitor, depending on their availability during production.
a
- THE FOLLOWING ITEM NUMBERS ARE NOT SHOWN. 41.42,43,44,. ab
NOTICE TO ALL PERSONS PECEWING THIS DRAWING CONFIDENTIAL. Reproduction forbiéden without the
Sry npn in ar ncense te use ne subject mall o the
- 3 LEQD the susyet mater thereot uniess by writen agreement / & 2b pe@D ‘with oF writen permission trom the corporation
3 EOD SECTION | =e)
ARR
Figure 5-1 Ultra Tank Final Assembly A030227-01 E
Figure 5-1 Ultra Tank Final Assembly Parts List
Item | Part Number _ | Qty Description —]
| 1 | A009975-02 | 1 | asey., Cabinet W/Graphics | ||
| 2 | 12009976-01 | 1 | Assy., Control Panel Sec Fi | ||
| 3 | A009980-01 | 1 | Assy., T.V. Shelf 5 | Figure 5-5 |
| 4 | AONS794. | 1 | Coin Door ASSy Se | jeure 5-6 |
| 5 | ‘n009959-02 | 1} | Assy, Door Rear W/todl | |
| ‘ | n007902-01, | 1 | coin’pox assy |
7 | n007197-01 1 | Poser Supply Assy See Tigure 5. a | ncos262-06 1 | RP shield Box assy
| 9) | 030185-o1 | 1 | Rp Shiela Pca assy See Figure § |
io | acosso1-o1 1 | P.c. Board Assy See Figure
| Uf | 0077¢¢-03 | 1 | Strain Relief Power Cord assy |
12 | no30230-01 1 | Power Switch & Harness Assy 33 | 78-24007 4 | Cable Tie, eat stablicee
| aa | (009965-01 | 1 | Plex sereen #/Graphics |
| 15 | 009945-01 | 1 | Plex Retainer |
| 16 | (000869- 01 | 2 | Speaker Grill |
| a7 | 002728-01 | 2 | Bracket. Panel urs. |
| a8 | 48-004 | 2 | speaker 5" (arkay) |
| 19 | 009974-01 | 1 | seze1 weraphics |
| 20 | 005233-01, | 1 | Rear poor seal |
| 2 | 00687001 | a | Coin Box Brkt |
22 | 46-2023002 2 | Fuse 3amP (Slow Blow)
| 23 | 75-0108 | 1 | Washer, Flat #10 |
| 24 | 907103-01 | 1 | onsoft ‘switch cover | |
| 25 | 73-7008 | 8 | Rivers 3/16 x 60" tg. | |
| 26 | 75-5516B | 4 | carriage Belt 4-20 x 1.00" Lg. B1k |
27 | 75-0158 6 | washer Fiat, 4"
| 28 | 75-9905058 | 4 | Nut, Lock Shallow Pat. Nylon, 4-20 |
| 29 | 75-045 | 4 | Washer, split-tock, &” | |
| 30 | 75-935 | 2 | wing wut, 4-20 | |
| 31 | 82-80248 | 1} | screw, Bot. Hd., Socket #10-32 x 1.50" Lg. BIk |
32 | 72-6812 20 | Screw, 5.8. Self Tapping #8 x .75 Lg.
| 33 | 75-98090006 | 5 | well mut, Blind Hole Fastener | |
| 34 | 82-8016 8 | 4 | screw, But. id,, Socket #10-32 * 1.00" Lg. gik | |
| 35 | 75-07021 | 4 | Washer, Flat, Black Nylon, #10 |
| 36 | 75-07002 | 2 | Fender washer | |
| 37 | 75-9158 | 2 | Nut, Hex, 4-20 |
| 38 | 82-1824 | 4 | Screw, Wood #8 x 14" La. | |
| 9 | 72-8608 | 12 | Screw, S.m. Pan Hd. Phil. #6 x |
aL a2
a4
50. Iten |_Part_Nomber oe DESCRIPTION 72-6610 006305-01 tM-107
st-107 A009978-xx 00997001
930190-01 A030191-02
A030194-01
15-040 75-9108 92-1836, i
Ref Screw, S.M, Pan Hd. Phil, #6 x 5/8" Lg. Printed Poly Bag Operation, Maintenance, and Service Manual omplete w/tPC Self Test Procedure Chart Shipping Container Patent Drawing
Harness scuematic See Figure b-10 Main Harness & Audio Control/Test SW Assy
BK & W TV Harness
Washer, Split-Lock #10 Wut, Hex #10-32 Screw, Wood #8 x 2.25" tg. A. ATARI
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
NOTICE TO ALL PERSON
CONFIDENTIAL Serr
oraming
agreement laith oF matten permission from the corporation
5 . > READ
- SECTION AXed\
| j | AT | eT 42 |
ex(ccai] Ewe woe (wn. egw ee /-
| sry | / (OO) eel | skeogyte |
Fl / | 7 /- \ RT Belcow)] Ewe / \ aa
| @) | (@ | . | NEO} cee |
NY we
| ~ | / | \ | \ | BKICOM) |
RT
#2
| (ho) | je | / | JEL | |
| FWD | REV | ‘ | EB (COM) | AW (N-0.)) |
‘oul ow
| sy | ROME | Pa | Nee er | PMOR | ley | ca |
*) eKicou) | REV #1 TW oTHl
Sate. Ea
| aK | = | eK | eS | BK | = |
_~ uti “ on an vw ce BE st #2° REBOUND BARRIER INVISIBLE.
Figure 5-2 Control Panel Assembly A009976-01 D
ATARI" Figure 5-2 Control Panel Assembly Parts List
Item Part Number Qty. Description
1 009966-01 2 009947-O1 3 001856-01 4 62-002 5 A002303-02 6 A002303-01 7 75-5536N 8 75-0158 9 75-045 10 75-915S
14 A030192-01
15 61-1lic 16 75-6610
© A Warer Communications Company VNNNUNKHNYPE Panel, Control W/Graphics Control Panel Board Aluminum Bushing, Switch LED Switch Assy, Joystick (Without Button) See Figure 5-4 Assy, Joystick (With Button) See Figure 5-3 Bolt, Carriage 4-20 x 2.25" Lg. Washer, Flat #4 Washer, Split Lock #5 Hex Nut #%-20
Control Harness McGill Toggle Switch With Gold Contacts (3192-0063) Screw, S.M. Pan Hd., #6 x 5/8" Lg.
MiP Llrxldireez wee
OOMOAS SQ SSSSSns iC
DETAIL ]
Figure 5-3 NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction tor
ler the corporat Tenlicense nongntto reproduce his drawingrs granted or the subject matter thereot uniess by writen agreement swain-oF waten permission Irom the corporation
Joystick Assembly (Up, Down, and Fire) A002303-01
Figure 5-3 Joystick Assembly (Up, Down, and Fire) I Parts List ATARI
Part Number DESCRIPTION
| 1 | 002299 | Button | |
| 3 | 002302 | 1 | Spring Return |
| 5 | 002298 | 1 | Rod |
| 6 | 002294 | 1 | Bushing |
| 7 | 002296 | 2 | Washer, Return |
| 8 | 002293 | 1 | Hub |
| 9 | 002297 | 1 | Spacer Ring |
| 10 | 003207 | 1 | Switch Plate 11 |
| 11 | 002301 | 1 | Bracket, Switch |
| 12 | 002300 | 1 | Actuator |
| 13 | * A003583-01 | ] | Handle Assy |
| 14 | 75-2412S | 2 | Screw, Mach, Rd Hd, Phil #4-40x3/4 |
| 15 | 75-044 | 2 | Washer, Split Lock, #4 |
| 16 | 75-9145 | 2 | Nut, Hex #4-40 |
| 7 | 75-990512 | 1 | Nut, Hex, %-28 self Locking |
| 18 | 75-0198 | 1 | Washer, Flat, 5/16 |
| 19 | 75-06003 | 2 | Washer, Belleville Spring |
| 20 | 85-22F410 | 4 | Screw, Self-Tapping, #4x 5/8" Lg |
| 21 | 85-22F608 | 4 | Screw, Self-Tapping, #6 x 4" Lg |
| a | **65-081A | 3 | Micro Switch |
| 25 | 72-6608 | 1 | Screw, Sht. Met., Self-Tapping, Xrec, #6 x % Lg. |
Notes:
- Optional Handle Grip See DWG No. 003092 #% Acceptable Substitutes 65-091A, 65-101A, 65-111A. Li)
ZZLLLZZL Led
-O?e SHOWN) 2 ob (2)
Figure 5-4 NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL. Reproductien forbidden without ine specie writen permission of Atari, Inc. Sunayvale Californa. This drawing is only cenditvonally sued. and either receipt nor possession theree! conters or bansters any nglt m. oF license to use. the subject matter af the rawing or any design o* technical information shown thereon. norary ght reproduce this drawing or any part ar incor tnereot. except for manutacture by vendors porated and for manutacture under the corporation $ will ten license, nanight'o reproduce tis drawing sqranted oF tne subject maller thereot unless by whiten agreement with or mien permission trom the Corporation
Joystick Assembly (Dummy Button) A002303-02
Figure 5-4 Joystick Assembly (Dummy Button) Parts List
item Part Number | Qty. DESCRIPTION
| 2 | 002294 | 1 | Bushing |
| 3 | 002296 | 2 |Washer, Return |
| 4 | 002293 | 1 |Hub |
| 5 | 002297 | 1 | Spacer Ring |
| 6 | 003207 | 1 | Switch Plate 11 |
7 | *A003583-02 1 | Handle Assy
| 8 | 75-990512 | 1 |Nut, Hex, +28 Self Locking |
| 9 | 75-0198 | 2 |Washer, Flat, 5/16 |
| 10 | 85-22F410 | 4 Screw, Self-Tapping, #4x 5/8" Lg |
| 11 | 85-22F608 | 4 |Screw, Self-Tapping, #6 x 3" Lg |
12 | **65-081A 2 | Switch
| 13 | 72-6608 | 1 |Screw, Self-Tapping, #6 x 4k Lg |
Notes:
- Optional Handle Grip See DWG No. 003082 ** Acceptable Substitutes 65-0914 65-110A 65-111A
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the specitic walten permission of Atar, Inc. Sunnyvale Californva. This grawing 1S only cordivorally issued. ang either receipt nor possession thereol conters or tansters ary right in. 0: hcense lo use. the subject malter of the drawing oF any design or technical information srowa to veproauee this drawing orany part vanufacture dy vendors of Alar IREOr porated and for manvtacture under the corporation s writ Tenlicense no right to rearoduce thisdrawing's granted or ‘he subject matter thereo! unless by written agieement wath or written permission from the corporation.
Figure 5-5 TV Shelf Assembly A009980-01 A
Figure 5-5 TV Shelf Assembly Parts List
ATARI
Part Number = Description
009947-01 92-029 006319-02 75-5120N 75-5132N 75-0108 75-040 75-9118 Shelf, T.V. TEC (TM-600) 19" B/W Monitor or Motorola (M-5000) Copyright Decal 1977 Bolt, Carriage, #10-24 x 1.25" Lg. Bolt, Carriage, #10-24 x 2.00" Lg. Washer, Flat #10 Washer, Split-Lock #10 Hex Nut, #10-24 WN RN EWN WH FRrENNAo OH
© a werner communications Company
me
a __| aces iO}
2 2 pics BS ames
- 2eLeS
T 2eus
Lyre |
NOTICE 10 ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction forbidden without the specilic written permission of Alani Inc, Sunnyvale Caktormia. Ths drawing 's only conditionally sued and neither feceipt nor possession thereof confers ar tansters any night in oF ligense to use Ihe subject mater of the Grawing oF any design oF technical yalormation shown thereon narany right to reproduce thisarawing or any oat! thereo! except for manutaclure by venders ol AtarIncor Dorated and lar manufacture under the corporation s wit ten license no right 9 reproduce this drawing saranted oF the subject matter tercot unless by wrtlen agreement wih of written permission from the corporation
Figure 5-6 Coin Door Assembly A006794-01 E
Figure 5-6 Coin Door Assembly I Parts List ATARI’
| Item | Part Number | Qty. | Description |
| 1 | 4007637-01 | l | Front Bezel Assy, - Used only on -01 Coin Door Assy. |
A007637-02 Re£.] Front Bezel Assy. - Used only on -02 Coin Door Assy. 4007637-03 Ref.} Front Bezel Assy. - Used only on -03 Coin Door Assy. A007637-04 Ref.| Front Bezel Assy. - Used only on -04 Coin Door Assy.
| 007637-05, | Ref.| | Front Bezel Assy. - Used only on -05 Coin Door Assy. |
A007637-06 Ref.| Front Bezel Assy. - Used only on -06 Coin Door Assy. A007637-07 Ref.| Front Bezel Assy. - Used only on -07 Coin Door Assy.
| 2 | 75-9165 | 4 | Nut 6-32 | |
| 3 | 4007639-01 | 1 | Coin Lock-Out Assembly | |
| 4 | 4007640-01 | 2 | Coin Switch Assembly | |
| = | A002465-01 | i | Coin Counter Assembly | |
| 6 | 004320-01 | 1 | Coin Door Weldment | |
| 7 | 004341-01 | 2 | Secondary Coin Chute | |
| 8 | 9004344-01 | 1 | Key Loop | |
| 9 | 004340-01 | 2 | Spring-Return | |
| 10 | 004337-01 | 2 | Bracket, Wire Form | |
| iL | 004338-01 | 1 | Lock» Out, | re Form, R.H. |
| 12 | 004336-01 | 1 | Lock-Out, Wire Form, L.H. | |
| 13 | 004326-01 | 2 | Button, Scavenger | |
| 14 | 75-046 | 4 | Lock Washer, #6 | |
| 15 | 006904-01 | 2 | Spacer | |
| 16 | 007359-01 | 1 | Lamp Socket | |
| 17 | 70-11-47 | 1 | Lamp | |
| 18 | 73-3008 | a | Retaining "C" Ring, Truarc #5103-25 | |
| 19 | 75-9914001 | 6 | Self-Threading Not, Tinnerman #SR188006 | |
| 20 | 75-0268 | 4 | Washer #6 | |
| 21 | 75-00516 | 13 | Kepnut, Style 842, St)., 6-32 | |
| 22 | 008629-01 | 2 | Spring | |
| 23 | 71-2118 | 1 | Lock Assembly, Hudson Lock | |
| 24 | 71-1225cU | Coin Mechanism for American Quarter only |
71-125FB Coin Mechanism for Belgian 5 Francs Only 71-121MG Coin Mechanism for German Mark only
| 71-121KS | 2f.] | Coin Mechanism for Swedish Krona Only |
71-12100¥d Coin Mechanism for Japanese 100 Yen Only 71-1210PE Coin Mechanism for English 10 Pence Only 71-1220CA Coin Mechanism for Australian 20-Cent Piece only 007753-01 Plate, Anti-Probe A007638-01 Switch Assembly - Slam A006921-01 Harness Assembly
H 10-261Z00V Ajquiassy Ajddng 4amod £-g aan3i4 kill eee
a i i ll it oy it i lL. (leeeet) jocee ye | deoeeeh ao Ul Bost
ATARI Figure 5-7 Power Supply Assembly Parts List
a ———
| Item | Part Number | Qty. | Description | | |
| 1 | A009266-01 | 1 | Power Supply Base Weldment Assembly | |
| 2 | A006886-01 | 1 | Transformer Termination Assembly "Type B" | |
| 3 | 29-053 | 1 | Cap., Sprague Electrolytic 26,000pf @ 15V | |
| 4 | 78-70501SC | 1 | Brkt., Cap. Mtg. Sprague #4586-48 | |
| 5 | A006555-01 | 1 | P.C. Board Rectifier | |
| 7 | 79-4411004 | 5 | Fuse Holder, Panel Mounting | |
| 8 | 41-2003 | 1 | Filter, Power Line, 5 AMP | |
| 9 | A006958-C1 | A/R | Volt Sel Block 95V | |
| lo | A006958-02 | " | Volt Sel Block 110V | |
| ll | A006958-03 | " | Volt Sel Block 205V | |
| 12 | A006958-04 | 7 | Volt Sel Block 220V | |
| 13 | 78-2708 | 1 | Grommet ,Plastic | |
| 14 | 72-1810S | 9 | Screw Pan Hd., #8-32 x 5/8"Lg. | |
| 16 | 75-048 | 9 | Washer, Split-Lock #8 | |
| 17 | 75-9188 | 9 | Nut Hex #8 | |
| 18 | 75-018S | 8 | Washer Flat #8 | |
| 19 | A007192-01 | 1 | Power Switch Termination | |
| 20 | A007444-01 | 1 | Power In Harness | |
| 21 | 46-203801 | 1 | Fuse, 8 AMP, 125V, 3 AG Fast-Acting | |
| 22 | 46-201251 | 2 | Fuse, 24 AMP, 125V, Slow-Acting |
LOCATE APPROXIMATELY
WHERE SHOWN FARSIDE
[o
io) CDEFHI KLMNPRSTUVWKYT BRBSYRESSRB 2 cows Thea] [08 [fare A of S600 8 AJOO Z ROW 1 6g { al
af Ac ROW 2
34567 8 SIMI 1314 15 117 1B 19202122
i= B< [-=} ES és uu Oo at °° fe) o|%
g Be E: fo) eo}
(SMALL
1oPLG@) al
CAPS)
3 PL)
\OOxh INDS)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING.
A ATARI Figure 5-8 RF Shield PCB Assembly Parts List
| Item | Part Number | Qty. | Description |
| 1 | 006549-01 | 1 | P.C. Board |
| 2 | 79-51 7222 | 1 | Connector, 44 Pin P-C. Mount |
| 3 | 27-259104 | 15 | Cap, Cer Disc 9.luf, 25V |
| 4 | 27-A250104 | 10 | Cap, Cer Disc 9.1uf, 25V (small) |
| 5 | 41-3003 | 9 | Inductor, 100uh |
| 6 | 41-3004 | 4 | Inductor, 1091h (small) |
| ? | 52-003 | 7 | Jumner, .60 Centers |
| 8 | 52-004 | 7 | Junser, .3Q Centers |
| 9 | 909468-01 | 1 | Decal, R.«F. Shield Label |
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING,
CONFIDENTIAL: Reproduction lorbidden without the
ness by written agreement ‘or wniten permission from the corporation.
Ener? p Not
Rize oan THAME + 4700-4
Ultra Tank PCB Assembly A009801-01-02 Figure 5-9 B
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Figure 5-9 Ultra Tank PCB Assembly Parts List Orsatwosaa = ve zatzaten ante Ten ce'zH © Ta eu) zMs (sts ova BH ete wwe ta om errr ora OTN en bata
ue rad set bet cer uotssiaa LOword TOTO wy {wold ota soruderp yuey, exiTh
’ a ZH we “ Tota sen 5 woag suds xueg, ezITH Trwo1e99H ‘weL vcore “wey X0S9S0H ¥ENOATO peaesboauT Ha 960°ZT Te3SAz2 uorqzesur dad ‘UTE ob ‘39x00 (ezewn) pedtrs (QUTS3e2H pooTwAL) ‘uSHED (vooTwax) >uTsIeeH (EcEWT) xuTS3E9H serD "26-94 "Kon ‘ann oe ze1g GUI YooT *ro4seN oe aera ‘zoyseEM, sea) Bi |X 26-9 4" THUd ‘PH Uva ‘emaz0S di @ X ‘UsaS ‘UOITAS AqreqUOWOK “USES 'YOTTAS
eeestee 9Te6 «© WENOATD peqexboqeT ezent z03e[nbou pootwas any Orpny SEEWT . . EES, f ‘ Tees. " :
zie TOe6 © -ENSATD —paqesbegur To-Btzoco. To-ELt0e0 TO-zc toL0 To-eet0c0 To-9ct0c0 10-<c t0c0 T0-pet0Lo To-#z0060 zooe-06 pt0L-06 ot09-06 zot-06 ovoz~6L s003t-ee, 9toET-ae, 2z090-84 0090-84, 29 T6-3e, 9s0-s 9t0-se, gogt-2e arastT-99 T00-29 eucstee~Le otee-ue EzeWT-LE yootwas-Le oct zt act 42t eet set yet tt zet wr ozt ert BIT “tt vt et
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
AR -02 Version ATARI Tem | Part Number _| Qty. | Description 1 | 003802-01 1 | P.c. Boaxa 2 10-5101 4 Res, Carbon, 5%, YW 100 OHM Bone . L * wT My RL, 2,4)5,205 ° rorsno8 ° 16, 52,67 169,95,
313,127 4 | 10-5103, 36 |” . "8 10K 99,9 14,40, 43.53-
61,72-77 86-94 104-106,114 115 ua-121 s | 10-5103 4 . . “im R23,28,111,112 6 | 1o-sis2 afc . * Lex 263 , 84,85 7 | 10-222 a “oo * 212K R17 a | 10-5223 1 soe RLS 9 | r0-se24 2 7 . 221,26, to | 10-5225 2 ” * 20,25, at | 10-5332 3] oc * 26,762 12 | 10-5335 2} . a2, 45, 13} 10-5392 1 so R18 14 | 10-5393 a ” . RS 1s | 10-5473 2 nd R102, 103 ae | 10-sara 2 . * 22,27, 17 | 10-5683 2) . R24,29 re | 10-5822 r|° . R19 19 | 10-5823 1 so . x12 20 | 19315502 1 | trimpoe R109 zi | 19315253 2 | Trimpot Ral Ad 22 | 19-Bn9W2P0 i | es, Wirewouna 20H R122 23 10-5471 4 Res, Carbon, 5%, hw R123-125,128 24 | 10-56a1 1 ew R126 25 | 19-52: 1 oom me ze | B-iottos 2 | cap wise, r00¥, Bars 27 | 24250106 2 Electrolytic 25v. lout on2,43 20 | 24-250227 1 " " 220ue ay 29 | 24-250208 1 . . * Looue 72, 30, 24- 250478 1 = " " 4700uL cs ai | 27-250104 35)" Ceramic Disc,25v, .luf 126,32, 46.47 51
93-55, 58,73 (© oor conmnciontoninr
a a2 6. n Part_Nunber 27-250103 3 CAP Ceramic Pisc, 25V .OLuf 27-250102 5 ” . n * L001ue 27-250224 1 « J "Jaane 28-101221 1 " pipped Mica, 190V__220pf 24-250225 2 “ Blectrolytic 25v2.2ue 31-aL4F 2 Diode, ALAF 31-1N914 2 Dioae, IN914 33-2n3644 2 ‘Transistor, 2N3644 34-M3E3300 1 ‘Transistor, MJE3300 37-7400 4 Integrated Circuit 7400 37-7402 1 . = 7402 37-7404 7 . "7404 37-7408 7 ” “7408 37-7410 L ” " 7a10 37-7414 2 . . 7414 37-7420 1 " "7420 37-7432 4 . 7432 37-1437 x " 7437 37-7418 74 5 . " 7ans74 37-741875 3 7 * 7aus75 37-7483 2 7 "7483 37-7486 2 * "7486 37-7490 1 . * 7490 37-7492 2 . "7492 3774125 1 7 "7412s 37-74153 1 : "74153 37-7418157 3 * "7408187 37-7418163 12 " ” 7ans163 37-74164 2 . “ 34 37-74Ls165, a ” “ 7ars165 37-74166 L he “74166 37-7418175, 3 : “ 7aus175, 37-74719 1 . “74279 37-555 2 . "955 37-14042 1 id "14042 37-0997 2 " ~~ ar97
€33,36,57 €52,67-10 ces 36, 28,29 cR5,6 CRI, 2 Q1,2 BA, H7,39¢K9 NLL 2,£3,F3,H3.L3 BS,M9 A2,D2,P2,C4,F? 37,011 Dio, m2 R6 ©2,R3,J8,mL cs 4 ,D5,L9, 10 R10 C6,06,F6 R5/P6 ¥9,B10 ES c3,D9 P10 no M3,N3,P3 B4,54,L4,M4,NA PA,LS,MS,N5/PS, P7,R7, B8,F8 K7,L7.M7,N7,KB 18,MB,NB FS, 4,5 ,RB bu ca,pe 33,83
Ultra Tank PCB Assembly Parts List Figure 5-9
-02 Version Part_Nunber 7 DESCRIPTION Item | part_Number gty. 79 | 37-9301 4 Integrated Circuit 9301_——B-R4,#9,NLO 133 so | 37-9312 3 . * 9312 FLO,KL1,L12 134 al } 37-9321 1 7 " 9321 mo 135 | 030178-01 vitra Tank Program Ron 1 D1 82 | 31-9334 1 = . 93340 ELL 136 | 030179-01 nc es! 83 a . - M339 12 aa a Audio AMP TDAl00§ B12 85, 1 Requlator M323 6 | 37-9316 1 Integrated Circuit 9316 HB 87 | 37-7418273, a ” ” 7408273 10 a9 | 62-001 1 Switeh, SPST, Momentarty SH (A5) 90 | se-aierrr 1 Switch, SPST, X 8 DIP Sw2 (RO ot 94 | 72-1608¢ 2 Screws, Pan Hd, Phil-, 6-32 x 4 Ug Cres 95 | 75-016 2 Washer, Flat #6 96 | 75-056 2 Washer, Lock Int Star #6 97 | 75-916¢ 2 Not, Hex, 6-32, Cres 101 | 78-06001 1 Heatsink (14323) 102 | 78-06022 2 Heatsink (1A1004) 103 | 78-13016 a/R|} Cement, (TA1004 Heatsink) 104} 78-16005, 1 Silpad (14323) 208 | 79-42040 t Socket, 40 Pin, MED Insertion C3 n0 all 312 | 90-102 L Crystal 12.096 Miz n us 116 | 90-6010 a Integrated Circuit Mcs6502 o 117| 90-7014 8 Ram, 2102-A HD, I2 K2T, 202
N2,P2,R2 lis } 90-7002 1 Ram, MC6B1OALI al lis 321 | 03002401 a Ultra Tank Syne Prom PB 122] 03017401. a s 8 wank PECL 6 123 | 030175-01 1 | M6 124) 030176-01 1 se mg 16. 125 | 630177-01 1 et Gg x6 128 | 030172-01, 1 Wltra Tank Graphics PIC Prom 1 46 129 | 03017391 1 ee mo te 130) 030218-01 2 * "color prom 10
Ultra Tank PCB Assembly Parts List Figure 5-9
E TO ALi PERSONS RECEIVING THIS DRAWING
4 PIN EDGE
CONNECTOR
Be gw TW 'hineness 5
FOR POWER SUPPLY
nov SE EEE moron OUT _Senehintic see” OO1197-01 = E ape Soe 58 Se zi EFERZELTOVG EA . Fi Fi | f A ce P| ag ear = Beco Bean ef?
a2) FI
srven & fala lelotet tn is es etic]
FRONT view
CABINET
Figure 5-10 Harness Schematic
INFORMATION
This chapter provides servicing information taken from the Motorola and TEC service manuals. Each manual has been reprinted by permission of the respective monitor manufacturer. Your game will include the Motorola or TEC monitor, depending on their availability during production.
MOTOROLA Service Manual
A. GENERAL INFORMATION This manual contains information on the M5000/M7000 monitor series and the +5 volt logic power supply. The M5000 uses a 19-inch CRT and the M7000 uses a 23-inch CRT. Ail CRTs are of the magnetic deflection type with integral implosion protection.
All monitor power supplies are capable of producing both +73 and +12 volts regulated from either 115-volt or 230-volt AC input to the transformer primary. All monitor variations described herein require a composite video input signal.
SAFETY
- Safety procedures should be developed by habit so that technicians rushed with repair work automatically take precautions.
- A good practice, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.
- Extreme care should be used in handling the picture tube as rough handling may cause it to implode due to atmospheric pressure (14.7 lbs. per sq. in.). Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Input and output connections for the monitors are made through a 12-pin connector plug located at the rear of the chassis. Inputs consist of composite video, audio, and 115/220 volt AC three-wire.
All monitors employ: four stages of video amplification, a two-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep Circuit, a one-stage spot kill, a one stage blanking amplifier; and a regulated, full-wave bridge power supply.
Model Breakdown Chart
Model Video Input 19" CRT 23" CRT|
IM5000-155 Composite x
IM7090-155 Composite
- An isolation transformer should always be used during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in personal injury from electrical shocks. It will also protect the chassis and its components from being
72 (SY MOTOROLA Data Products _ carovstream, iLLNois 60187 PART NO, 68°25253A47 COPYRIGHT 1977 BY MOTOROLA, INC. PRINTED INU.S.A,
damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.
- Always replace protective devices, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.
- Before returning a serviced unit, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock. Do not use a line isolation transformer when making this test. a 1000.0 M/VOLT {OR HIGHER) AC VOLTME TER. NOTES: 1. REPEAT EACH CHECK WITH THE LINE CORD
REVERSED IN THE POWER OUTLET
2 METER READING MUST NOT EXCEED 7% VOLTS AC. “ROT” LEAD OF METER 10 EACH EXPOSED PART OF CABINES, AS WELL AS THE CABINET | GROUND LEAD OF METER TO ANY EARTH |] GROUND SUCH AS A COLO WATER HPE Ny
Voltmeter Hook-up for Safety Check L In addition to practicing the basic and fundame tal electrical safety rules, the following test, which is related to the minimum safety requirements of the Underwriters Laboratories, should be performed by the service technician before any unit which has been serviced is installed in a game again.
A 1000-ohm-per-volt AC voltmeter is prepared by shunting it with a 1500-ohm, 10-watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.
The AC voltage indicated by the meter must not exceed 7% volts. A reading exceeding 7% volts indicates that a potentially dangerous leakage path exists between the exposed portion of the unit and earth ground. Such a unit represents a potentially serious shock hazard to the operator.
The above test should be repeated with the power plug reversed, when applicable.
Never reinstall a monitor which does not pass the safety test until the fault has been located and corrected.
Table 6-1 Motorola Monitor Electrical Specifications
MODEL M5000-155 MODEL M7000-155
PICTURE TUBE
standard 19" measured diagonally (48.2 cm); 184 sq. inch viewing area (1188 sq. cm); 114° deflection angle; integral implosion protection; P4 phosphor 23” measured diagonally (58.4 cm); 282 sq. inch viewing area (1820 sq. cm); 110° deflection angle; integral implosion protection; P4 phosphor standard
POWER INPUT 115/230 VAC, 110 Watts (nominal); 60 Hz provision for 230 VAC, 50 Hz
FUSES M5000-155, M7000-155—0.8A
+73 VOLT SUPPLY to 260 VAC Electronically regulated over AC inputs from 103 VAC to 130 VAC, or 260 VAC
VIDEO INPUT 0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT
RESOLUTION 500 lines at picture center
LINEARITY Within 3%, measured with standard EIA ball chart and dot pattern
Table 6-1 Motorola Monitor Electrical Specifications
HIGH VOLTAGE 17KV (nominal)
HORIZONTAL BLANKING INTERVAL 11 microseconds typical (includes retrace and delay)
SCANNING FREQUENCY Horizontal: 15,750 Hz+500 Hz; Vertical: 50/60 Hz
ENVIRONMENT Operating temperature: 10°C to 55°C (ambient) Storage Temperature: —40°C to +65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure UL listed under specification 1410 (electronic components)
TYPICAL DIMENSIONS 14.11" H, 18.18" W, 14.83” D (35.8 x 46 x 37.6 cm) 16.72" H, 21.56" W, 16.18" D (42.4 x 54.7 x 41 cm)
Specifications subject to change without notice.
B. SERVICE NOTES
Circuit Tracing Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, control names are also shown and referenced on the schematic diagram in this manual.
Transistor elements are identified as follows: E—Emitter, B—Base, C—-Collector.
Component Removal Removing components from an etched circuit card is facilitated by the fact that the circuitry (copper foil) appears on one side of the circuit card only and the component leads are inserted straight through the holes and are not bent or crimped.
It is recommended that a solder extracting gun be used to aid in component removal. An iron with a temperature-controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foi! due to over-heating.
The nozzle of the solder extracting gun is inserted directly over the component lead and when sufficiently heated, the solder is drawn away, leaving the lead free from the copper foil. This method is particularly suitable in removing multi-terminal components. CRT Replacement Use extreme care in handling the CRT, as rough handling may cause it to implode due to high vacuum pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection. In addition, be sure to disconnect the monitor from all external voltage sources.
- Discharge CRT by shorting 2nd anode to ground; then remove the CRT socket, deflection yoke and 2nd anode lead.
- Remove CRT from the front of the chassis by loosening and removing four screws, one in each corner of the CRT.
Adjustments A non-metallic too! is recommended when performing the following adjustments.
Regulator Adjustment
- Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
- Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service.
- Adjust HOR. SET coil L1 until display is stable.
4, Connect a DC digital voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q17, or any +73 voit test point.
- Adjust the 73V ADJUST. control, R93, for an output of +73 volts. Do not rotate the control through its entire range; damage to the monitor may result.
- When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible.
Horizontal Hold/Oscillator Adjustment Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical or the CRT display is stable (synced).
Vertical Height/Linearity Adjustment
- Connect a test generator whose output is similar to the display signal normally used.
Motorola Monitor Circuit Board in Service Position Figure 6-1
- Rotate the vertical size control, R60, until the smallest display is obtained.
- Adjust the vertical linearity control, R64, until the top and bottom of the test pattern is equally spaced.
- Readjust R60 until the desired display height is obtained.
- Readjust R64, if necessary, as in Step 2 above.
Focus Adjustment The best overall focus of the display is obtained by adjusting the focus control, R42, for best focus ata point which is near the center and approximately 1/3 down from the top of the display.
Monitor Servicing The monitor circuit board may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see Figure 6-1).
C, THEORY OF OPERATION Power Supply The power supplies are transformer-operated, full-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.
+78 Volt Supply (See Figures 6-3,6-4) When the +73 volt supply attempts to increase, the voltage at pin 3 of !C1 will increase, while the voltage at pin 2 remains constant due to D20. The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (pin 6) to increase the forward bias of Q19, The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of Q17 collector-to-emitter voltage wili cancel the attempted output voltage increase.
When the +73 volt supply bus attempts to decrease; the voltage at pin 3 of 1C1 will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19. The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series
COMPOSITE VIDEO
EMITTER VIDEO VIDEO MPL / INPUT FOLLOWER. PREAMPL, are Woeo Go €
f HORIZ Horiz, ‘AFC c 415/230 REGULATED pies | = VOLTS ac POWER | ——O+12V INPUT SUPPLY TOR woriz pak onveR
sy Sync. Yat ‘SEPARATOR ANPL. ety Sal Wear | vest yess Bae ese | OEE
Figure 6-2 Motorola Monitor Block Diagram
R84 Iso iow an? sew REGULATOR
1K woo 020 SEK 39K
om a Fa aus aie S| > a EG, BUFFER
Figure 6-3 +73 Volt Supply Circuit with the output, will decrease proportionally to the attempted decrease in the outbut bus.
Resistor R84 shunts a portion of the output current around Q17 so less power is dissipated within the device. Resistor R82 is the current-limiting resistor for Q18, and R86 controls the leakage current of Q17. Resistors R83 and R85 are the collector load for Q19, and R88 and R87 provide an emitter voltage for Q19 within the range of IC1’s output voltage variations. Capacitor C45 filters high frequency variations from the voltage at pin 7 of IC1, and C49 is a Miller-effect capacitor which eliminates instability. PARABOLA FROM EMITTER OF Q17
EXISTING VERTICAL SAWTOOTH WITHOUT VERT. PARABOLA ADDED
PARABOLA PULSE AND VERTICAL SAWTOOTH ADDED TOGETHER, HENCE PRODUCING THE REQUIRED VERT. DRIVING SIGNAL
Figure 6-4 Motorola Monitor Vertical Drive Waveform
+73V +150V ce R14 po — 9 ie GQ.
| a | viDEO | a | fee fans | 2855 | |
| 100% | G2 | [ PREAMe | ae | Bix | By, |
| 2 | G_ | Tel | 5242 | .05 | van | Pak |
| car | RL | = | => |
PLO
| PL | QL AGH | 82 | av | 4 [cio | |||
| TT | Ro | aay | qs | Fao2 = | |||
| COMPOSITE — | cl | EMITTER | tev | & | 522 | ||
| VIDEO 2 < | FOLLOWER | rs | aad | os] | 03 | a | os |
| nur | | | ear | 2 | P2S | 6.8K | Ae | OUTPUT $R19 |
| 7 | 1Ng2348 | 470K | |||||
| | | wos | 3 | lv | {+ +01 | an | the | |
| H | + | = | |||||
| i | C4 22 | aL | |||||
| GND 2 | 22 | He? | vied |
1 1.2K
| 4 & | = | = | DRIVER | ||
| 4 | fz | 0B | |||
| weee wee | 50 | c4a | Fars | zeorr | |
| CONTRAST | pig 330PF | 022 == | VIDEO | ||
| ‘ | a7PF | 56 | B a | TO PIN 7 | |
| 70.033 | = | = | Rie: | == | (CATHODE) |
| = | ed | OF V1 (RT) |
\ Via R78
TO Q10 eMuTTER 10011 COLLECTOR
Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit
Capacitor C32A filters horizontal frequency variations from the output bus,
Resistor R91 provides bias current for 020, and the value of R99 presents an impedance from pin 2 of IC1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output bus, back to pin 3—preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equal to the voltage of pin 2 of IC1. Resistor R95 provides bias current for D21 and also provides the +12 volt output. Diode D23 is necessary to temperature-compensate for variations within D21. Capacitor C32B filters AC variations from the output of the full-wave bridge.
Video Amplifiers and Output (See Figure 6-5) The composite video signal is coupled to the emitter-follower Q1 through the input connector P1 and capacitor C1. Transistor Q1 is a buffer stage which matches the impedance of the signal source to the video preamplifer and the sync separator stages. Resistor R1 is a terminating resistor for the video signal source, and resistors R2, R3, R4, and R5 form the biasing network for the stage. Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Q1 to the sync separator Q10 through C33 and to the contrast control R6 through C47.
The contrast control varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct-coupled, common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedback arrangement of R9, R10, R11, and R12. Resistors R7 and R8 provide the base bias voltage for Q2. Capacitor C48 is used for high-frequency peaking.
The output of the video preamplifier stage is coupled to the video output stage through capacitor C4, Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when a sync pulse turns on the sync amplifier Q11. The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7, C8, and resistor R16 are used for highfrequency compensation, and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts, while capacitor C5 filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2, and R19 and D4 are used to limit the current through the CRT.
R23: 47K
Ta R20
cl 6 AG) HORIZ OSE, gag Q7 p2s HORIZ PULSE HAPER iz SHAPER 04) HORIZ DRIVER
a8 BASE
R371e23,
0027 3, 3Kyvew
Figure 6-6 Motorola Monitor Horizontal Deflection Circuit
Capacitor C10 AC-couples the video from the collector of Q5 to the cathode of the CRT if D4 turns off due to high beam currents. Resistor R17 is the collector load for Q5, and R15 provides the bias current for the zener diode D3. Capacitors C9 and C6 filter video frequencies from the +150 volt and +12 volt supplies. Resistor R14 and zener diode D1 are used to supply +12 volts for Q1, Q2, and Q3.
D. HORIZONTAL DEFLECTION CIRCUITS (See Figure 6-6) Phase Detector (See Figure 6-7) The phase detector consists of two diodes (DS and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base.
The horizontal output (Q9) collector pulse is integrated into a sawtooth by R24 and C12. During horizontal sync time, diodes D5 and D6 conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. If the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis, and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). The positive polarity causes the horizontal oscillator to speed up and correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D).
Components R23, C15, R25 and C17 comprise the phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor C13 times the phase detector for correct centering of the picture on the raster.
Horizontal Oscillator The horizontal oscillator employs the principles of the Hartley-type oscillator. Its operating frequency is sensitive to its DC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector. The main frequency-determining components are L1, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off. The initial forward starting bias is supplied via R26.
Horizontal Pulse Shaper and Driver The horizontal pulse shaper Q7 serves asa buffer stage between the horizontal oscillator and driver. Capacitor C20 and resistor R30 combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.
REFERENCE HORIZ. SYNC
OSC,ON FREQ NO CORRECTION VOLTAGE DEVELOPED
OSC,.SLOWS, POS. CORRECTION VOLTAGE
OSC.FAST, NEG. CORRECTION VOLTAGE
Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms
The horizontal driver Q8 operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.
Resistor R35 and capacitor C21 provide damping to suppress ringing in the primary of Tl when Q8 goes into cut-off. Resistor R36 is used for limiting currentin the collector of Q8, and C22 filters the horizontal frequency variations from the DC side of the transformer primary. Horizontal Output (See Figure 6-8)
The secondary of T1 provides the required low drive impedance for Q9. Resistor R37 limits current in the base of Q9, while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which once each horizontal time period connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of T2. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The horizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Momentary transients at the collector of Q9, should they occur, are limited to the voltage on C27, since D8 will conduct if the collector voltage exceeds this value.
The damper diode D7 conducts during the period between retrace and turn-on of Q9 to reduce retrace overshoot; capacitor C28 is the retrace tuning capacitor. Capacitor C25 blocks DC from deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor 32D is charged through D10, developing the video output supply voltage.
B HORIZ LIN 9OO™ laa HORIZ YOKE
| case | Wh | ow | + | i | Have RECT. |
Qs 7696 270 339pF to m1 HORIZ OUTPUT og) —
30) ‘DAMPER [01 VOLTAGE! : C29, , D647 5 FOR VI cr + r ie TO PNT 1 cal
| iL | 7M | B | at |
| L | pi | = |
01 12
| Ika2 FOCUS | qrosisov | HY. | |
| a a | tloseo | TRANS. | 7 |
| 10 | ~ | 20 | CRI |
| ws | ' | L | 2nd ANORE |
R43 +7 ‘ we
| Tac | R19: | REO | al | ’ |
| Sexe | 56x | 10 | ||
| a cAT | esa ee | RevICA? |
TS reo aw rt eee
Figure 6-8 Motorola Monitor Horizontal Output Circuit
EMITTER
VERT, SYNC. INTEGRATOR T0 C36
Figure 6-9 Motorola Monitor Sync Circuit Syne Circuits (See Figure 6-9)
The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negativegoing sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction. The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information.
Resistors R45 and R46 provide base bias for Q11. The composite sync pulses are amplified and inverted by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for Q11, and also provide base bias for Q12. Resistor R50 limits current through the base-emitter junction of Q12, and R51 is its collector load. Components R52, C34, R53, C35, and R54 form a double integrator which removes the horizontal pulses from the composite sync signal, leaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.
Vertical Oscillator and Output (See Figure 6-10) The vertical oscillator is a relaxation oscillator and operates at a free-running frequency that is set by
+73V
4.7K roos Ve | R58 @ COLLECTOR name av ps7, 12 3.aKe MPU 6027 VERT. osc. B2v VERT. OUTPUT
Figure 6-10 Motorola Monitor Vertical Oscillator Circuit
the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until D12 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When D12 conducts, C37 and C38 are discharged to nearly zero volts; then D12 turns off and the cycle repeats. The value of R61 and the setting of R60 determines the amplitude of the waveform.
Diode D14 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14; D13 provides temperature compensation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Q15.
The vertical choke 15 acts as a current source during linear scan time and provides a high-voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.
Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical non-linearity will result unless some compensation is employed.
Resistors R64 and R62 couple the emitter voltage of Q15 to the junction of C37 and C38. This path is resistive, and the waveform coupled back will be integrated by C38. This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of C37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40 couples the signal to the vertical yoke winding and blocks DC.
Spot Kill (See Figure 6-11) The spot kill circuitry is used to reduce the effect of the electron beam concentrating on one area of the CRT after the monitor is turned off. The circuitry is accomplished by raising the arm of potentiometer R73 to the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the highvoltage charge that normally remains in the CRT.
When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage required to keep Q20 on. When the monitor is turned R73 BRIGHTNESS
TO R77 CRT, PIN2
Figure 6-11 Motorola Monitor Spot Killer Circuit
off, the falling +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 prevents the negative voltage swing at the base of Q20 from exceeding the reverse voltage rating of the transistor.
Blanking Amplifier (see Figure 6-12) The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field. Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses, while R69 determines the amplitude of the horizontal pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R70 allows C41 to discharge when the retrace pulses swing below zero volts. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.
Figure 6-12 Motorola Monitor Blanking Amplifier Circuit
(contrast) / 1 u (HORIZ. OSC.) R73 (BRIGHT) paz (Focus) 12
Figure 6-13 Motorola Monitor Chassis Rear View —Component Location
ae es a Pa e Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View
POWER SUPPLY
Figure 6-15 Motorola Monitor Schematic Diagram
+23V OUT. 4 (NOT
SHOWN) SHOWN)
pa ~~ (NOT
R64 —sR6D VERT. VERT. D12 013 LIN. | SIZE D23 018 1C1
R66 D21 p2q 920 06 71 a7
Pi Q1 P5 CONTRAST
R7;
BRIGHT
Figure 6-16 Motorola Monitor Circuit Board Detail—Component Location
Table 6-2 Motorola Replacement Part Numbers
| rer PART
| NUMBER | DESCRIRTION | No. | NO ARIER | DESCRIPTION | |
| Capacitors: | C31 | 8S10191B98 | -01, 10%, 250V; Poly. | ||
| All values are in Microfarads unless otherwise noted. | C32 | 23$10255B73 | 20/200, 400/125, 600/100, | |||
| cl | 23S10255A27 | 47, SOV; Lytic | 200/50; Lytic | ||
| C2 | 21S135660 | 05, +80-20, Z5V, 50V; | C33 | 8S10191A51 | -033, 10%, 160V; Poly. |
| Cer. Disc. | 34,C35 | 8S10191A32 | 047, 10%, 250V; Poly. | ||
| C3,C4 | ——-23$187A26 | 22, 25V; Lytic | C36 | 21$180E60 | .01, +80-20, Z5V, 50V; |
| cs | 21$180E60 | .01, +80-20; Z5V, 50V; | Cer. Disc. | ||
| Cer. Disc. | C37, 38,39 8S10191B67 | (0.22, 10%, 250V; Poly. | |||
| co | 215135660 | .05, +80-20, Z5V, 50V; | c40 | 23510255A60 | 100, 63V; Lytic |
| Cer. Disc. | cH | 8S10212B16 | =—-0.1, 20% , 400V; Mtlz. | ||
| c7 | 218131625 | 330pf, 10%, XSF, 500V; | Poly. | ||
| Cer. Disc. | C42 | 21$180C82 | 0.33, 10%, N150, SO0V; | ||
| ca | 21S180B87 | 220pf, 10%, X5F, SOOV; | Cer. Disc. | ||
| Cer. Disc. | C43 | 8S10191B67 | 0.22, 10%, 250V; Poly. | ||
| C9 | 8510191B99 | 015, 10%, 250V; Poly. | C44 | 23510255B28 | 4.7, 100V; Lytic |
| c10 | 8510212B18 | 0.22, 10%, 400V; | C45 | 8S510191B90 | -033, 10%, 250V; Poly. |
| Mtlz. Poly. | C46 | 218132492 | .01, +80-20, Z5V, 100V; | ||
| cu | 218131625 | 330pf, 10%, X5F, 500V; | Cer. Disc. | ||
| Cer. Disc. | C47 | 23$10255B63 | 100, 10V; Lytic | ||
| C12 | 218180C41 | .0027, 10%, Z5F, 500V; | C48 | 21S180D56 | 47pf, 10%, N750, 100V; |
Cer. Disc. Cer. Disc.
| C13 | 21$180C02 | 10pf, 10%, N150, 500V; | cag | 21S180B51 | -001, 10%, XSF, 500V; |
Cer. Disc. Cer. Disc.
| C14 | 21$180D34 | .005, 20%, Z5F, 1KV; | | |
Cer. Disc. Diodes:
| C15 | 23S10229A32 | 1.0, 16V; Lytic | DI | 48S10813A03 | Diode, Silicon, Zener; |
| C17 | 8510191B90 | -033, 10%, 250V; Poly. | IN5242 | ||
| C18 | 8510299B28 | 01, 10%, 100V; Polycarb. | 02 | 48D67120A13_ | Diode; A13 | |
| C19 | 8510299B29 | .0082, 10%, 100V; | D3 | 48510813A01 | Diode, Silicon, Zener; |
Polycarb. IN5234B
| 20 | 8510191B98. | .01, 10%, 250V; Poly. | D4 | 48S191A02 | Rectifier, Silicon; 91A02 |
| C21 | 21S180B51 | .001, 10%, X5F, 500V; | D5,D6 = 48D67120A11_— | Diode; A11 | |
| Cer. Disc. | D7 | 485134921 | Diode, Damper; D1D | ||
| C22 | 8510191B98 | .01, 10%, 250V; Poly. | D8 | 488134978 | Diode, Pulse Lim; D1K |
| O23 | 23510255B50 | 150, 10V; Lytic | D10 | 48S5191A05 | Rectifier, Silicon; 91A05 |
| C24 | 21S180B51 | .001, 10%, X5F, 500V; | D11 | 488137114 | Rectifier, H.V., D2Y |
| Cer. Disc. | Di2 | 485137638 | Vert. Osc.; MPU6027 | ||
| C25 | 8S10299B27 | 0.82, 10%, 200V; Mtlz. | D13,D14 | 485191A05 | Rectifier, Silicon; 91A05 |
| Polycarb. | DI5 | 48D67120A11_ | Diode; A11 | ||
| a | 215131625 | SBOP 10% XSF, 500V; | De, Dig’ 485191405 | Rectifier, Silicon; 9105 | |
| C27 | 8S10212A11_—-1.0, 10%, 630; Mtlz. | D20 | 48S10813A02 | Diode, Silicon, Zener; |
Poly. 1N5231B
| C28 | 8510571A06 | .01, 5%, 1200V; | D21 | 48510813A03 | Diode, Silicon, Zener; |
Polyprop. Foil 1N5242
| C29 | 8510212B53 | 0.47, 10%, 630V; Mtlz. | D22 | 48D67120A11 | Diode; A11 |
Poly. D23,D24 48S191A05 Rectifier, Silicon; 91A05
Table 6-2 Motorola Replacement Part Numbers
| E | | | Part No. | | | Description | Ref | Part No. | Description |
| Fuses: | R60 | 18D25245A29 | Vert. Size; 250K | ||||
| Fl, F2 | 658138269 | Fuse, 0.8A-250V | R64 | 18D25245A31 | Vert. Lin ; 100K | ||
| ow | R66, | 6S$10201A04 | Varistor, 1 ma, 120V, 0.5' | ||||
| Integrated Circuits: | R73 | 18D25245A28 | Control, Brightness; 200K| | ||||
| 1C1 | 51S10732A01 | Ref. Ampl.; T3F | R84 | 178135589 | 150, 10%, 10W | ||
| R93 | 18D25245A21_ | Control, +73V out Adj.; |
Coils/Chokes: 2.5K
| 1 | 24C25448A01 | Coil, Horiz. Osc. | ROS | 10731A03 | 1.5K, 10%, 5W |
L2 24D25603A09 ~—- Coil, Horiz. Width
| 1B | 24D25248A14 | Coil, Horiz. Lin. | Switches: | ||
| y | 24D25261A09 | Coil, Defl.(M5000-155, | swi | 40S10624407 | Switch, Slide; D.P. D.T. |
M5010-155)
| 4 | 24D25261A10 — Coil, Defl. (M7000-155, | Transformers: | ||
| M7010-155) | 1 | 25D25221A05_—_Horiz.Driver | ||
| bs | 25D25221C12_ | Choke, Vertical | T2 | 24D25240B23__-H.V. Transformer |
| : | T3 | 25D25239B20 | ‘Transformer, Power |
Trauaistoys: (M5010-155, M7010-155)
| Qi | pic a | Emitter Follower; AGH | B | 25D25239B30 | Transformer, Power |
| Q2 | 488137172 | Video Pre-Ampl.; A6] | (M5000-155, M7000-155) | ||
| Q3 | 488137127 | Video Pre-Ampl.; P2S | |||
| Q4 | 485134952 | Video Driver; A2) | Misc. Electrical Parts: | ||
| Q5 | 485137476 | Video Output; BIE | V1 | 96241401 | 19"-CRT; Type 19VARP4 |
| Q6 | 485137172 | Horiz. Osc.; A6) | (M5000/M5010) | ||
| Q | 488137127 | Horiz. Pulse Shaper; P28 | yj | 96510848401 | 23"-CRT; Type | |
| Qs | 485137093 | Horiz. Driver; ASF | M22VATP4 (M7000/ | ||
| Qo | 485137570 | Horiz. Output; B2L | M7010) | ||
| Q10 | 488137173 | Sync Separator; P2W | |||
| Qu | 485137172 | Sync Ampl.; A6) | Mechanical Parts: | ||
| Q12 | 488137172 | Vert. Sync Integrator; A6J | 9B25456A01 | Block, Fuse (F1, 2) | |
| Q13 | 488137172 | Vert. Sync Ampl.; A6) | 42D25158C01 | Clamp, Defl. Coil | |
| Qu | 485137639 | Vert. Driver; MPS A13 | 26510251A08 | Heat Sink (Q5) | |
| Qis | 485137596 | Vert, Output; B2V | PI | 15S10183A69 — Housing, Connector; | |
| Qt6 | 485137172 | Blanking Ampl.; A6) | Female (12-Contact, | ||
| QI7 | 485137368 | Regulator; ASW | Less Contacts) | ||
| Q18 | 488134952 | Reg. Driver; A2) | 39$10184467 | Contact, Plug; 5 Req’d | |
| aig | 485137476 | Reg. Buffer; BIE | M5000/M7000, 9 Req'd; | ||
| Q20 | 485137476 | Spot Kill; BIE | M5010/M7010 | ||
| P2 | 15$10183A82 | Housing, Connector; |
Resistors/Controls: Male (3-Contact, Less
| the description when ordering standard values of | P2 | 15810183481 | Housing, Connector; |
fixed resistors up to 2 watts. Female (3-Contact, Less
| R6 | 18D25245A27 | Control, Contrast; 500 | Contacts), M5010/M7010 | |
| R14 | 178135204 | 100, 10%, SW | 39S810184A67 | Contact, Plug; 3 Req’d |
| R17 | 17810731A01 | 3.9K, 5%, SW | for P2 | |
| R36 | 17S10130B07 | 1.5K, 10%, 3W | P3 | 28510586A35_ — Header, Connector; |
| R42 | 18D25218A14_ = Control, Focus; 2M | 2-Contact |
Table 6-2 Motorola Replacement Part Numbers
REF. PART NO. NUMBER DESCRIPTION PART ~ |
NUMBER DESCRIPTION
P4, PS 15$10183B12
39$10184A84
$2 15$10183A81
82 15S10183A82
39810184464
$3 15810183A94
39S10184A72 Housing, Connector; Female (3-Contact, Less Contacts) M5010/ M7010 Contact, Plug; 3 ea. Req'd for PS, M5010/ M7010 Housing, Connector; Female (3-Contact, Less Contacts), M5000/M7000 Housing, Connector; Male (3-Contact, Less Contacts), M5010/M7010 Contact, Receptacle; 3 Req'd. for $2 Housing, Connector; Female (2-Contact, Less Contacts) Contact, Receptacle; 3 Req'd. for $3 14B25459A01
144562353
14C25230A01
14S10157A30
14S10550A02
35136050
9D25470A01
9D25201A01
9C63825A03
41D65987A01 insulator, Fuse Cover | (Fi, 2) Insulator, Mica (Q9, Q15, Q17) Insulator, Molded (On D11 Body) Insulator, Nylon (2- Req'd.); Mtg. P.C. Board Insulator, Transistor Cover (Q9, Q15, Q17) Screw, Tpg; 6-20x¥%2 CLU Pan (Mtg. Q9, Q15, QI7 and D111 Socket) Socket, CRT; Incl’s. R77, R78, R79, R80 Socket, H.V. and CRT Anode
Socket, Power Transistor
Q9, Q15, Q17) Spring Special; CRT Aquadag Gnd. |
A. GENERAL
TM-600 and TM-623 is a television monitor for video games. It is designed for operation either from a power supply of 115 volts/50-60 Hz AC or 230 volts/ 50-60 Hz AC. The complete monitor incorporates a picture tube, an integrated circuit, 20 silicon transistors, 18 silicon diodes, 2 germanium diodes, anda high-voltage selenium diode.
This model is equipped with 5V/3A power supply for the operation of the TTL control board and operation double-pulse-type AFC circuit to obtain a stable picture.
B. SPECIFICATIONS Power Supply Input 115 volts/230 volts 50-60 Hz +10%
Power Consumption 60 watts
Video input 0.5 volts composite P/P for 100 volts 2.5 volts P/P maximum Sync negative at input TEC VIDEOELECTRONICS INC. SERVICE MANUAL
Picture Tube 19” (500 mm), 114° deflection for Model TM-600 23” (584.2 mm), 114° deflection for Model TM-623 Integral implosion protection
High Voltage 18 KV nominal at 0 microamperes beam current
Horizontal Retrace Time 12 microseconds maximum
Resolution 500 lines minimum at picture center
Scaning Frequency Horizontal:15.750 Hz +500 Hz Vertical: 50-60 Hz
Tone Burst Amplifier 5 watts peak output with TTL drive at nominal line, fully adjustable. 4 watts peak output at low line.
Environment Operation: Maximum ambient temperature 50°C (122°F) Storage: Temperature range from —40°C to +65°C
Model TM-600 and TM-623 Monitors
TEC Videoelectronics Inc. (TVI) 3010 Scott Boulevard Santa Clara, CA 95050 89
DEFLECTION CENTERNG YOKE RINGS: HORIZ. LIN.
Pt CONKECTOR
Figure 6-17 TEC Monitor Chassis, Rear View
cn08 e901 EBNoensen —-SVSEGULATOR 4, g ‘cont REGULATOR CONDENSER
ce
VERT. OUT TRANSISTOR
—— 0305 VERT. OUT TRANSISTOR
POWER TRANS,
RESISTOR conr.
BRIGHT ‘VERT. HOLD ‘VERT. LIN,
VERT. HEIGHT
Figure 6-18 TEC Monitor Chassis, Top View
HORIZ, DRIVER TRANS.
HoRIz, OUTPUT HoRIZ. osc. con.
vingo outeut
nw rect
HV TRANS
vert. BALANCE wioTH com
aRIGHT ‘CONTRAST
Figure 6-19 TEC Monitor Printed Circuit Board, Top View
Table 6-3 TEC Monitor Replacement Parts Numbers.
Ref. — Ref. a
No. Part No. Description No, PartNo. Description
| Electrical Parts: | Q303 5300500201 | MPS9700U__ Vert Amp | |
| PCB1 | 2215303600 | Main PCB | or MPS834 |
| A801 | 485TM60003 ~—«s CRT PCB | Q304 4310400030 += 2SC1106._~—Vert Output |
305 or 2N6307
| Transistor and IC: | Qaoo 5310500202 | MPS9700T | Phase Inv | |
| Q200 5310500202 =» MPS9700T | 1st Video Amp | or MPS834 | ||
| or MES834 | Q401 | 5310500202 | MPS9700T | ~—Horiz Osc |
| Q201 | 5310500261 | MPS9750T | 2nd Video Amp | or MPS834 |
| or MPS4356 | Q402 5310500410 | 2N6558 | Horiz Amp | |
| Q202 5310500410 | —-2N6558~—=—-Video Output | or MJE9742 |
or MPSU-10 or 2N4354
| Q301 | 5310500261 | MPS9750T | Sync Separator | 403 5310400040 = 2SC1875_—-Horiz Output |
or MPS4356 or MJ205
| Q302 5310500201 | MPS9700U Vert Osc | *Q901 | 5310400030 = 2SC1106-—- | Power Regulator |
or MPS834 or MJ3430
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref. a Ref.
No, Part No. Description No. Part No. Description
| Q902 5310500410 | 2N6558_ | «Regulator Amp | . | |||
| or esi0sto7s | ‘IAPs. Li0a | T401 | 589514015 | TLN-S06BX__Horiz Osc | ||
| 903 5310500280 | LM1796-—séReference Amp | 7402, | 589516012 | EENS19 | Horlzbiive | |
| or MPS-DO1 | * 1403 | 589517017 | TFB-1006AS._F.B.T. | |||
| Q904 5310500450 | MJ2955 | 5V Regulator | * 7901 | 589519021 | TPW-600 | Power Trans |
CRT and Diode: Resistors
| * vao1 | 5380000060 © 500SB4. | «CRT | R201 | RD-4L471) | 470 ohm] % W |
| D203 5340200280 | MR9712__ | Silicon Diode | R202 | RD-41223) | 22 K ohm J % W |
| or IN4004 | LV. Rectifier | R203 | RD-4L563) | 56K ohm) %W | |
| D204 5340200430 © IN4148. | Silicon Diode | R204 | RD-4L471) | 470 ohm) % W | |
| or IN4002 | Blanking Clip | R205 | RD-41332) | 3.3K ohm) %W |
D205 5340200430 += IN4148._—_—sSilicon Diode
| R206 | RD-21823 | kK | WwW | ||
| or IN4002 | Blanking Clip | wor | noatseo) | ms nn u Ww | |
| 1206 5340200430 | IN4148.—_—_ | Silicon Diode | emma | ||
| ‘or 1N4002 | Blanking Clip | R206 | RD-4L102) | 1K ohm J %& W | |
| D207 534020280 | MR9712—-200V Rect | R210 | RS-029562) | 5.6 K ohm J 2 W | |
| or IN4004 | R215 | RD-42101) | 1K ohm J % W | ||
| D301 | 5340200260 | = MR-9701_Rectifier Silicon | * R216 | RD-4L101) | 100 ohm) % W |
| Diede | * R217 | RD-4L470) | 47 ohm) %W | ||
| D401 5340100040 = A143. | Phase Det | R28 | RD-4L223) | 2Kohm}) %*W | |
| D402 5340100040» | A143 | Phase Det | 19, | RD-41563) | 56 Kohm | HW |
| Diss 5340200300 | -MR9722.~—-« | Damper | fen | e109) | 1Kchm | %w. |
| D404 5340400120 | TV20-2K80) H.V. Rectifier | R221 | RD-4L102) | 1Kohm) %W | |
| ae | R222 | RD-21102) | 1K ohm J ¥% W | ||
| D801 5340200290 | MR9713.—-400V Rectifier | ” | ohm | % | ||
| “ | R223 | RD-2L102) | 1K ohm) %W |
D901 5340200270 ~—»« MR9704.—sRectifier
| or IN4005 | Silicon Diode | R224 | RD-21122) | 1.2 Kohm J 2 W |
| D902 5340200270 | MR9704.-_—séRectifier | * R226 | RSOIPION) | 100 ohmJ 1W |
| or IN4005 | Silicon Diode | R227. | RD-2L123) | 12K ohm) % W |
| D903 5340200270 | MR9704._~—séRecctifier | R228 | RD-2L105) | 1.5K ohm) %W |
| or IN4005 | Silicon Diode | R229 | -RD-4M6a1) | «680. ohm) %& W |
D904 5340200270 MR9704_—_—Rectifier
| y | 33 | “Ww | |||
| or IN4005 | Silicon Diode | om | in ‘asco. | - “rm h w | |
| D906 5340300220 | ~—«INS858A_—-Zener Diode | . | ean) | ||
| or 3340300310‘ | INGO02A | R304 | RD-4M102) | 1K ohm) % W | |
| D907 | R308 | RD-4M104) | 100 KohmJ %* W | ||
| Boos 5340200690 | MDAQ970-1_— | Rectifier | R309 | RD-4M155T | 1.5 Mohm] % W |
| D910 | R310 | RD-4M332) | 3.3 Kohm) % W | ||
| coils | and | R311 | RD-4M563} | 56K ohm } % W |
oils and Trans:
| *L401 | 589515015, | TDY1005 | —_D.Y. Coil | R312, | RD-4L182) | Takohm) | WwW |
| L402 | 589512015 | HCH1005 — Horiz Choke | R313 | RD-4L153) | 15 K ohm J % W | ||
| Coil | R314 | RD-4L183) | 18K ohm J %& W | ||||
| L403. | 589512012 | HC2-035 | Choke Coil | R315 | RD-4L203) | 20K ohm J %* W | |
| 1404 | 589512012 | HC2-035 | Choke Coil | R316 | RS-2P333) | 33K ohm J %&W | |
| L405 | 589514013 | AZ-9177DM_ Width Coil | R327 | RD-4L104) | 100 K ohm J % W | ||
| L406 | 589514016 | LH-15]54 | Lin Coil | R320 | RD-4L124) | 120 Kohm J % W |
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref.
R322
R323
R324
R326
R339
R331
R332
R333
R334
R336
R337
R338
R339
R340
R401
R402
R403
R404
R405
R406
R407
R408
R419
R410
Rail
R412
R413,
R414
R415
R416
R417
R418
*R420
*R421
R422
R425
R426
R802
R804
R811
*R901
R902
R903 Part No.
RD-4L224)
RD-4L433)
RD-4L471)
RD-41.152) RD-4L101) RD-4M331
RD-4L102) RS01P682) RD-2L183) RD-4L221)
5160122901
RS-2P 150)
5160112901
RS01P220T
RD-4L153) RD-4L821) RD-4M561} RD-4M103] RD-4M103) RD-4L272) RD-41681) RS02P682) RD-4L270) RD-4L182)
RD-4L151) RD-4L561}
RSO1P682)
RD-2L221) 5160122903
RD-2L569) RS02P182} RSO1P123}
RX05P220) RD-2569) RD-4L153) RD-4L153}
55337153
RD-2L154) RD-2L474)
RD-2L561)
RX20P251} RD-2L101) RD-2L123] Ref.
Description No. Part No. Description
| 220 K ohm J % W | R904 | RD-2L123) | 12K ohm J % W |
| 43 K ohm) % W | R905 | RD-21223) | 22K ohm] % W |
| 470 ohm) % W | R906 | RD-2L563) | 56 K ohm J % W |
| 1.5K ohm) %W | R907 | RD-2L563) | 56 Kohm) %W |
| 100 ohm) % W | R909 | RD-21682) | 6.8K ohm J % W |
330 ohm} % W
| Macsuinenened | Ta | S53 102005 | 1K oh | Contrast |
| oe) | R319 | 553104005B | 100 koh ot. ee | |
| aon | R321 | 5531240088 | 220K ohm__Vert, Height | |
| 20 ohm) % W | R327 | 5534720088 | 4.7K ohm Vert. Linearity | |
| Bex SHER, itd | R335 | 553102007B | 1Kohm_ Vert. Balance |
15 ohm) %W
| R427 | 553303005B | 30 Kohm_ Horiz Hold | ||
| 12 | ohmJ % W | R803 | 553254005B | 250K ohm_Bright |
- ohmJ 1W
| Ra05 | 5532050058 | 2Mohm | Focus |
15K ohm J % W
| R908 | 5534720078 | 4.7K ohm B+AD) |
820 ohm) % W 560 ohm) % W Capacitors:
| 10 Kohm) % W | C201 = CE2G1C470 | 47 mF | 16V | ||
| 10 K ohm J % W | 202 | CE2G1F101 | 100 mF | 25V | |
| 2.7K ohm J % W | C203 | CE2GIC220—- | 22 mF | 16V | |
| 680 ohm) % W | 204 | CE2GIH101 | 100 mF_— | 35 | |
| 4.7K ohm J %W | C205 = CE2G1C220 | 22 mF | 16V | ||
| 27 ohm) %W | C206 | CISLIHS61K | 560 pFK | 50 | |
| 1.8K ohm) % W | 207. | CE2G0)221 | 220 mF | 6.3V | |
| 150 ohmJ % W | C208 | 5270322401 | 0.22mFM = 400V | ||
| 560 ohm) % W | 209 | CE2G2F229. | 2.2 mF | 315V | |
| 6.8 Kohm J 1W | C210 = CE2G1H220 | 22 mF | 35V | ||
| 220 ohm$S %W | C211 | CE2G1H339 | 3.3 mF | 50V | |
| 22 | ohmJ | iW | C213. | CKIF2ZH102K | 0.001 mF_—500V |
| 5.6 ohmjJ %W | C220 = CE2G2F220 | 2.2 mF | 250V | ||
| 1.8K ohm J | 2W | C301. | ~=CQIM1H473K | 0.047 mF K 50V | |
| 12 | Kohm J 1W | C304 | CKIBIH391K | 470 pFK—-50V | |
| 22. | ohm] 5W | C305 | CEXGIH478. = 0.47 mF = 50V. | ||
| 3.6 | ohm) %W | C306 = 56405333 | 0.033 mF K SOV | ||
| 47 | ohm] 1W | 307 | CQIM1H562K | 0.0056 mF K 50V | |
| 15KohmJ % W | 308. | CQIM1H273K | 0.027 mE K_50V | ||
| 15 K ohm J % W | C309 | CQIM1H123K | 0.012 mF K_ 50V | ||
| 150 Kohm % W | C311 | CQIMIH124K | 0.12 mF K-50V | ||
| 470 Kohm) % W | 312. | CQIM1H392K | 0.0039 mF K 50V | ||
| 2MQ) %» W | 313 | DS5D1C229M_— | 2.2 mF | 16V | |
| 250 ohm] 20 W | C314. | CQIM1H474) | 0.47 mF | 50V | |
| 1Kohm] %W | C315 | CQIM1H333K | 0.033 mF K_50V | ||
| 12 Kohm} % W | C316 = CF2G1A470 | 47 mF | 10V |
Table 6-3 TEC Monitor Replacement Parts Numbers
[ Ref.
Z803
Switches:
| *SW-1— | PE13-1567 | 115V/230V Power Line |
Slide Switch LL
No. Part No. Description a Part No. Description
| C317 | CE2G2A101 | 100 mF | 100V | Fuses: | |
| C318 | CKIE2HI03K | 0.01 mF_—-500V | *F902 | 6990620011 | 250V 2 Amp. |
| 3195270370301 | 0.01 mF | —-630V | *F903 | 5990610013 | 250V 0.5 Amp. |
| C401 | CQIMIH103K | 0.01 mF K50V | F904 | 5990630010 | 30V 5 Amp. |
| C402 | CQIMIH103K | 0.01 mF KK | 50V | ||
| C403 | CQIM1H393K | 9.039 mF K 50V | Mechanical Parts: |
KOOT — 22-463020 Mate-N-Lock Connector (AMP)
| Co | Chibanio] | Tet: | ov | 60085005 | Fdge Collector (Molex) | |
| eats | CEG IHS39 | 333 nk | ad | S-A3915 | Transistor Socket (SMK) | |
| C406 | CQIMTHI04K | 0.1 mFK | SOV | *TM60085001 | Fuse Holder | |
| C407 | CQIM1H223K | 0.022 mF J. 50V | or *TM60085001 | Fuse Holder | ||
| C408 | =CQIM1H683K | 0.068 mF J. | 50 V | KOO5 — 1-380826-0 | Stand-Off Fastener (AMP) | |
| C409 | CE2G1F470 | 47 mF | 25 | 401 | PET9-1569 | 4P Plug Assy. (Yoke Line) |
| C410 | CKIB2H681K | 680 pF K | 500V | P402.—- | PE19-1570 | 4F Recep Assy (Yoke Line) |
| C411 | CK1B2H222K | —-0.0022 mF K 500V | P403. | PE19-1571 | 3P Connector Assy. (Video | |
| C412 | CK1B1H152K | 0.0015 mF K 50V | Input) | |||
| C413. | CK1B1H102K | 0.001 mF K 50V | A621 | PE19-1572 | 4P Connector Assy. | |
| *C414 | CKIB3D471K_— | 470 pFK | —-2KV | (Q901 Line) | ||
| C415 | CQIM2A104K | 0.1 mF K | 400V | A631 | PE19-1573 | 6P Connector Assy. |
| *C416 | 5270333201 | 0.0033 mF | 1.5KV | Keser vine | ||
| 417 | CE2C2C100 | 40 mF | 160V | P4060 | PE19-1574 | 2P Plug Assy. (Heater Hine) |
P407 — PEI9-1575, 2P Recep Assy. (Heater Line)
| Ca1a | 5270333401 | 0.33 mF K | 200V | TE9O1 PE19-1576 | Terminator, 6 Pin | |
| C419 | 56635101 | 100 mF | 35v | £001 | 135431015 | Ground Plate |
| C420 | 56625471 | 470 mF | 25V | pen | Frame | |
| C801 | 5270356302 | 0.056 mF K 630V | HO03 5432001-1 | Plate Heat Sink A | ||
| *C901 | 5240700400 | 450 mF | 200V | Q403D 54320011 | Plate Heat Sink C | |
| 902 | 100 mF | 160 V | ||||
| C904 | F2G2C229 | 2.2 mF | 160V | |||
| 905 | CKIF2ZH102K | 0.001 mF | S00V | |||
| COT | 56625105 | 10000 mF =. 25V | ||||
| C912 | 56616018 | 1 mF | 16V |
bad Gaps: 1. Design and specifications are subject to change
without notice. zw2| 599030001 EGP-H751A
- J—Indicates + 5% tolerance K—Indicates +10% tolerance M—Indicates +20% tolerance
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Safety-Critical Components Components marked with an asterisk (*) on the parts list and with gray shading in the schematic have special characteristics important for safety. You may create shock, fire, or other hazards by using areplacement that does not have the same characteristics as the recommended part.
901-0908
' = pr g PL 10 PLT
Iw pur Zz 907 “D810 MORa70" |
_ 1901. ew-623 | ‘TPW-600
TR, IC, and Connector Lines
MPS ULO LMITA6.MPS 9417 INSSBA NPS U04 ps 9750MPS 9700 1NEOOZA nessa “PS 9750 ios
ace eos
MuES20 MuE105) me 7eosce —-MJES742
Of >
for G
Ms2955 28c1106 asc 1875, re
WAVE FORMS
NOTES
- Unless otherwise specified, all resistance values 4. All waveforms are measured with strong signal are in ohms. input and contrast set to give normal picture.
- Unless otherwise specified, in the schematic dia- 5. This schematic diagram covers basic or repregram all capacitor values less than 1 are expressed sentative chassis only. There may be some differin mfd, and values more than 1 are in pfd. ences between actual components on chassis and
- Voltage readings are taken with VTVM from point the schematic diagram. indicated on chassis to ground.
G20, CONTRAST g, MPSSTSOT
p40! aaia3 St paoz A149
Figure 6-20 TEC Monitor Schematic Diagram
R806 Z002) a ores 2 Ig
om 2 er fit a Ate a . ‘i i igh c | a
| "i k | 0 | 7 | t~ | |
| atl | an | | | He | & |
| q | E | all | ©3020) | |
| ps | 901 | pete | 0391 | |
| The | L | 0901-906 | e |
Y R901
mee Proertl b PPP P a
eee 9® oo
BOTTOM VIEW
Figure 6-21 TEC Monitor Wiring Diagram
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Cut along this line
TM-107 ‘1st Printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm CO) Distributor QO Operator
Address Other
City State Zip
First Fold
First Class Permit #1004 Sunnyvale, CA
g g Atari, Inc. 2 P.O. Box 9027 3 3S é Sunnyvale, California 94086
Attn.: Publications Group, Coin-Op Engineering
TTT ETT Second Fold SsCi—“—~s—sSCSC‘Ctis‘“SsSSSS 7
980%6 WO ‘aleAKuung 2206 XO@ “O'd “oul ‘Wel
36p3 siyy adey
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation Or improper testing.
In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may noi be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
le KEE GAMES ly
ATARI INC 1265 BORREGAS AVENUE RO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 « TELEX 35-7488