CATHODE RAY TOMES

F1 TM-088 1st Printing

Apricot F1 (ACT, 1984) · Technical Manual · 56 pages · 20 sections · original scan

Page 1

+ Operation, Maintenance

/ and Service Manual

Page 2

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation Or improper testing.

In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.

EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may noi be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 3

FL

Operation, Maintenance and Service Manual

ATARI INC. 1265 BORREGAS AVENUE SUNNYVALE, CA 94086 408/734-2000 e TELEX 35-7488

By the Publications Group, Engineering Department AM

ATARI Innovative leisure

Page 4

All rights reserved. Copyright © 1977 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

For permission requests, write:

PUBLICATIONS GROUP ATARI INC. 1265 BORREGAS AVENUE SUNNYVALE, CA 94086

3F

Lithographed in the U.S.A.

Page 5

1 LOCATION SETUP ... Introduction ..... Inventory of F-1

OU mk HOWTO ASSEMBLE F-1. So 5 Step 1

Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step & Step 9 GAME OPERATION CHECK .. MAINTENANCE AND ADJUSTMENTS OF F.1 . THEORY OF OPERATION ... CALIBRATION Attach Left and Right Top Hood Supports to Main Hood Assembly .. Attach Top Hood Panel to Join Together Assemblies of Step 1 to Assembly of Step 2 Attach Hood Assembly to Electronics Cabinet Assembly .. Attach Remaining Screws Attach Car Chassis to Electronics Cabinet Assembly Attach Steering Flex Cable to Car Steering Bar Arm Adjusting Voltage Selector to Match Voltage Source Checking for Proper Air Movement from Cooling Fan

Score Calibration ..... an 21. 45 Main Car Calibration Competition Cars Calibration .

Table 1 Table 2 Table 3 Table 4 LIST OF TABLES

Inventory of F-1 ... Final Checklist Adjustments Maintenance . 1.0... 6.6. c cece cence en enn nnn ee

Page 6

LIST OF

ILLUSTRATIONS

Figure 1 Inventory of Parts .. vee Tans geese Figure 2 Main Car Projector Lamp Mounting .......... Figure 3 Locations of Adjustment Potentiometers Figure 4 Maintenance of Competition Car Transport ........... Figure 5 Harness Schematic, Early Version ...... . Figure 5A Harness Schematic, Latest Version . Figure 6 CONT 1 PCB Schematic ...............0.00.000. 000% Figure 6 CONT 1 PCB Drawing Figure 6 CONT 1 PCB Parts List Figure 7, CONT 2 PCB Schematic . Figure 7 CONT 2 PCB Drawing ....... Figure 7 CONT 2 PCB Parts List Figure 8 DRIVE PCB Schemati Figure 8 DRIVE PCB Drawing ... Figure 8 DRIVE PCB Parts List . Figure 9 SOUND PCB Schematic Figure 9 SOUND PCB Drawing . Figure 9 SOUND PCB Parts List Figure 10 SCORE PCB Schematic Figure 10 SCORE PCB Drawing ...... Figure 10 SCORE PCB Parts List Figure 11 Game Start Circuit Diagram Figure 12 Drive Block Diagram .. 0.0... 26 e 0 ect eeeeeee Figure 13 Accident Block Diagram ............ Figure 14 Score Block Diagram... 6.0 6.2.0 eee cece eee eee Figure 15 Extended Play Block Diagram .. Figure 16 Cockpit Simulator Test Panel Schemat . 14 .. 16

. B

Page 7

LOCATION SETUP

Introduction Congratulations, you have just received an action-filled Atari driving game. The game is relatively easy to set up if you follow the instructions. However, there are many pieces to assemble. Please begin by ensuring that you have received all parts of F-1.

Inventory of F-1 Unpack all shipping containers. Inventory the parts by matching with Table 1 and Figure 1. If any parts appear damaged, contact your distributor immediately.

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9

Table 1 Inventory of F-1 Item | Qty. | Item Name Item Description

11|Electronics Cabinet AssemblyLarge black cabinet with two doors on

the back and a window on the front.

21 | Hood Main SupportMetal U-shaped bar.
32|Top Hood SupportMetal flat-top bar with one end

rounded and threaded.

42|Top Hood Support AttachmentFlat metal strip with four holes.
51|Hood TopPlastic hood top panel.
62 | Hood SidesPlastic hood side panels. Mirror images.
71 | Car ChassisRace-car-like fiberglass car body.
81 | SeatFiberglass car seat.
94 | KeysTubular security-type keys.

10 | 41 | Machine Screws Five assorted sizes. 11 | 28 | Flat Washers Four assorted sizes.

124 | Split Lock WashersCompression washers.
133 | Hex WrenchesThree different sizes.
141 | Projector LampSpare projector lamp.
151 | Cleaning ClothAntistatic cleaning cloth.
161_ | Extender CardPrinted circuit board with edge

connector on one end.

Page 10

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 11

How to Assemble F-1

There are basically two ways to assemble F-1

  • the easy way and 2) the hard way. It is beyond the scope of this manuai to discuss the hard way. Therefore we present the following—the easy way.
Page 12

Step ATTACH LEFT AND RIGHT TOP HOOD SUPPORTS TO MAIN HOOD SUPPORT Step 3 JOIN TOGETHER ASSEMBLIES OF STEP 1 TO ASSEMBLY OF STEP 2

(1 ea side) #10-32 Hex Nut (2 ea side) #10 Split Lock Washer (1 ea side) #10-32x1 Hex Head Screw

(1 ea) #10-32 Hex Not

(1 ea) #10-32x1 Hex Head Screw

(1 ea) 3/8-16 Hex Nut

NOTE: Screw nut all the way onto Top Hood Support

Step 2 ATTACH TOP HOOD PANEL TO ASSEMBLY OF STEP 1

  • #8-32x3/8 Pan Head Screw
  • #8-32x3/8 Pan Head Screw

Step 4 ATTACH HOOD ASSEMBLY TO ELECTRONICS CABINET ASSEMBLY

= SLOT FOR TOP AND SIDE HOOD PANELS

assemou HOOD ELECTRONICS CABINET ASSEMBLY

At the end of Step 5, snug these two adjustments to apply tension of the hood frame assembly against the hood panels.

  • Insert threaded end of both top hocd supports into holes of bracket along top front edge of Electronics Cabinet Assembly. . Insert one 1/4-20x1/2 hex head screw and one 1/4inch split lock washer into second hole from bottom of each hood side panel. Match screw holes in hood side panels with appropriate holes in Electronics Cabinet Assembly. Just barely start each screw. w

. Slowly tighten screw on each side of hood assembly while maneuvering top hood panel into slot across the top of the Electronics Cabinet Assembly.

Page 13

Step 5 ATTACH REMAINING SCREWS

1, Insert and tighten six 1/4-20x1/2 hex head screws and 1/4-inch flat washers in remaining holes of the hood side panels. . Insert and tighten one 1/4-20x1/2 hex head screw and 1/4-inch split lock washer into outside holes of “L" brackets located at the bottom of each hood side panel. Insert and tighten one #8-32x1/2 pan head screw and #8-32 split lock washer into inside holes of each hood side panel “L”" bracket. w

a . As illustrated in Step 4, snug adjustment screws and nuts to apply tension of the hood frame assembly against the hood panels.

  • Optional: Drivers of F-1 sometimes grab the hood assembly to climb into and out of the cockpit. This sometimes results in the dislocation of the Hood Main Support from the hood panels. To prevent the dislocation of the hood assembly, drill 0.1405inch holes through the plastic hood panels and into the Hood Main Support at locations as identified by asterisks. Insert #6 self-tapping screws into the drilled holes.

Step 6 ATTACH CAR CHASSIS TO ELECTRONICS CABINET ASSEMBLY

  • Align car chassis with centerline of Electronics 3. Attach car chassis to the Electronics Cabinet As- Cabinet Assembly. sembly with two 1/4-20x3/4 socket head screws and
  • Reach into front of car chassis and pull out flex ‘V4-inch split lock washers. steering cable and black harness wire with con- 4. Attach seat to car chassis with four 5/16-24x3/4 hex nector on one end. Pass both flex steering cable head screws and four 5/16-inch split lock washers. and connector of black harness wire through hole 5. Screw down feet located on outer sides of casters in front center bottom of the Electronics Cabinet under car chassis until casters are suspended Assembly. above the floor.
Page 14

Step 7 ATTACH STEERING FLEX CABLE TO CAR STEERING BAR ARM

  • Open rear door of Electronics Cabinet Assembly by unlocking and lifting door up and out of cabinet.
  • Remove packing from beneath racetrack turntable; remove paper from competition cars on top of racetrack turntable; and remove tape from main car steering arm.

MAIN CAR

PIVOT BAR |

SET SCREW

NOTE: Plug in connector of harness wire (passed through front of cabinet in Step 6 to COCKPIT connector, as illustrated in Step 8. Attach steering flex cable as shown below. . Pass power cord through hole in right-hand rear area (as you iace rear of cabinet) of Electronics Cabinet Assembly.

STEERING FLEX CABLE.

Tighten set screws on both sides of pivot bar for equal pressure on steering flex cable.

Page 15

Step 8 ADJUSTING VOLTAGE SELECTOR TO MATCH VOLTAGE SOURCE

WARNING, To prevent the hazard of electrical shock, unplug 1, Determine the AC voltage source into which you F-1 before handling any of the lamps on the score will plug F-1 (must be between 90 and 120 VAC). Panel or before handling any of the motors. 110 2. Locate voltage selector as identified below. Adjust VAC is wired directly to the racetrack, crash, and voltage selector for closest voltage of AC source. timer motors and to the lamps of the score panel within the electronics cabinet assembly. . Plug F-1 power cord into AC source.

Power Cockpit Score

[CONVENIENCE PLUG

Page 16

Step 9 CHECKING FOR PROPER AIR MOVEMENT FROM COOLING FAN

NOTE: We have discovered that some of the main projector cooling fan motors have been incor rectly assembled. The result is that the fan sucks air from the playfield and the playfield will warp from the heat of the projector lamp. Determine air movement from cooling fan by placing hand between fan blade and projector lamp. It fan blows air toward the projector lamp, proceed to next section. If not, perform the fol lowing . Remove fan from mounting and invert the fan motor stator as shown below.

MO FoR SEV COR,

Page 17

Game Operation Check

Your new F-1 was carefully checked before it left Atari. However, there are many things that could affect its operation during shipping. It is therefore necessary for you to provide the final step of quality control for F-1. This is accomplished by you climbing into the car cockpit, inserting two 25¢ coins and “driving” the game. While driving F-1, refer to the checklist in Table 2. If all items prove to be functioning, you'd best stand aside. There is probably someone anxiously waiting for his or her chance to drive F-1.

Page 18

Table 2 Final Checklist

Checked Item Response

© Projected Racetrack

© Projected Cars

  • Crash Scene

¢ Acceleration

© Gear Shifter

e Brake

© Steering Reasonably clear image on viewing screen.

Reasonably clear image on viewing screen.

Projected when main car comes in contact with:

  • Either of the two competition cars, or
  • Side of racetrack. When crash scene begins, score tally will “freeze” for approximately five seconds. When crash scene begins, sound of an explosion is heard on the game speaker.

Accelerator has two positions:

  • Partially depressed.
  • Fully depressed. Depressing the accelerator causes increase of motor sound,

Low gear has immediate and rapid accelerating motor response. High gear has gradual accelerating motor response.

Brake foot pedal:

  • Causes race track projection to decrease in rotational speed.
  • Causes squealing tires sound.

Steering whee! has smooth action and does not bind.

Page 19

MAINTENANCE AND

ADJUSTMENTS

OF F.-1

CAUTI Do not adjust potentiometers on printed circuit boards if potentiometers are glued with white glue. The consequences may cost you money.

—— NOTE: Early F-1 games were shipped with projector lamps that have a life span of approximately 100 hours. Later F-1 games were shipped with long-life projector lamps with a life span of approximately 500 hours. The two lamps require different mountings. If you desire a long-life projector lamp, get one from your distributor and refer to Figure 2 for proper mounting of the projector lamp.

There are few adjustments that need be made on F-1. However, there is one adjustment that you might check quite regularly. Due to heat buildup within the electronics cabinet assembly, the plastic suspension that supports the competition cars may sag. This will result in scratching the racetrack. Refer to Table 3 for adjustment suggestion. For other adjustment, also refer to Table 3 below. For maintenance suggetions, refer to Table 4. Figure 3 illustrates the locations of all adjustment potentiometers.

Page 20

Loosen both set screws to center prosector lamp ever contertine of

Se OT ue win nanas b nea! ana

Figure 2. Main Car Projector Lamp Mounting

Table 3 Adjustments

Problem Cause Cure

Volume too loud or too soft Volume controls incorrectly adjusted Brake volume: Rotate BRAKE potentiometer located on SOUND PCB clockwise to increase, counterclockwise to decrease. Accident volume: Rotate BONG potentiometer located on SOUND PCB clockwise to increase, counterclockwise to decrease. Allvolumes: Rotate MAIN VOL potentiometer located on SOUND PCB clockwise to increase, counterclockwise to decrease.

Page 21

Table 3 Adjustments

Problem Cause Cure

Accident scene appears every five seconds or not at all

Competition cars drag on racetrack

Repeat players winning too many games Photocell (CdS) adjustment is incorrect

Competition cars plastic suspension sagging from heat of projection lamp

Scoring is incorrect

NOTE: There are three photocells located on the main car (car on end of bar that moves with steering wheel). When light from main screen projector Jamp is interrupted from any one of these photocells, the accident scene should occur. Rotate CdS potentiometer located on CONT 2 PCB fully clockwise, then during game play slowly rotate counterclockwise until accident scene occurs when projection of main car comes in contact with either of the competition cars or in contact with shoulder (side) of racetrack.

Refer to Figure 4. Loosen nuts of two Phillips-head screws on vertical edge of ‘L’ bracket that mounts competition car to car drive mechanism. Adjust L bracket until car is between 2mm (5/64 in.) and 8mm (5/16 in.) above racetrack turntable.

Remove main screen projector lamp. 1, Adjust LOW potentiometer located on CONT 2 PCB for a game score result of between 2800 and 3200 (nominal 3000) points when game is driven with shifter in LOW gear position and accelerator is fully depressed for the duration of the game time.

  • Adjust HIGH potentiometer located on CONT 2 PCB for a game score result of between 7700 and 8300 (nominal 8000) points when game is driven with shifter in HIGH gear position and accelerator is fully depressed for duration of the game time.

Table 4 Maintenance

Item Maintenance Required

Racetrack turntable plastic

Electronics cabinet assembly Plexiglas window

Competition car transport

Blown fuse Spray glass cleaner on dust, then remove with clean soft cloth.

Spray glass cleaner on dust, then remove with clean soft cloth.

Refer to Figure 4.

Replace with only same size and type of fuse.

Page 22

COURSE SPEED

BACK WARD

FORWARD

MAIN VOL

@ BRAKE

os Tf iO BONG (crash) CONTROL ) FREQ

TURN POINT

cockeit

Do not lubneate, Remove dust trom all four nylon Loosen these screws to agjust tor proper clearance of cars above racetrack bushings and both lar meta! brackers

Lubricote bearings beneath large plastie gear with fight machine oi

Spray with nonabrasive housebols cleaner. Then wipe with ‘nistatic cloth

Figure 4 Maintenance of Competition Car Transport

Page 23

Theory of Operation

In this section, you will find most all that is necessary for determining how F-1 operates. This information is presented to you in two different forms—schematic and block diagram. The block diagrams illustrate the operation of F-1 during different modes of operation, These modes are game start, drive, accident, scoring, and extended play. You will find these block diagrams useful for troubleshooting F-1. To do so, identity the problem by determining the mode in which the game fails. Refer to the appropriate block diagram to determine the related circuits that are failing, then refer to the schematic diagrams to isolate the failing components.

Page 24

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Represuetion lorbidgen wathout the Specific wetton permission of Alar Inc. Sunnyvale ‘aitorma This drawing 1s only canditwnally sued ane nor possessica theteof conters or transters ight in or license to use. the subject matter of the 19g oF any design oF tactical information shown,

  • nav any righlt6 reprcdtuce this drawing or any part ‘ol. excep for manufacture By vendors of Alan incor fed and for manulacture under ine corporation 3 wr lense noright to reproguce thvsdraw ngs granted oF Lubject matier thereat unings ty writen agreement ih o¢ written permission trom the corporation CONTI

cont 2

ep? bs iran aca A

a 1 J

  • x 7 apr? ah

he I Hotte Vy Lo] ik S

= ea | Fesbrewonece

oe 8o - =e gz

ztvbaofel of foHEsstel fz22
© lal]=| af al |al]alyoals
alaafalfal]348

lela oe | & ‘eM %,

eeeaSis

Rada. | Ba aly ote latte

zaleeeaCesd

> Peat )>] SY > hal

TF nov

Figure 5 Harness Schematic, Early Version Sheet 1 of 3

Page 25

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction torbiaden without Ihe specitic written permission of Atari Inc Sumiyvale Catsigraa, This drawing 1s only conditionally sue an af ether receipt nor possession ther any right an. oF beense to use. th Sarawaing oF any design ar techn thereon norany righ! to reprogues teieot. except for manufacture by vendors of Atari incor orated and for manutacture une2s Ihe corporation s wet ten license, noright toreproduce thisdrawingis granted o+ the subject matter thereat unless. by wrilen agreement wath oF wrttlen permission tom the eomoralion

Goel so

cock PIT if - =e Pi] J

i | 7y LL

= ae HS

| _ i i | 7 5

whatrteoeg ef 2ae2
STLL|Jac| |
3] 4)Apr3~
ad}ieyaa‘
7}|Pen FATaPere
HEHILt
Bg BROBEokoit#8
OMMEE4sBE,ee

id Pearly

Figure 5 Harness Schematic, Early Version Sheet 2 of 3

Page 26

CAR, DISPLAY

cb Ret ERENCE NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the specitic awriten permassion of Alan Inc. Sunnyvale Eatormia This erawing 16 only conditionally issued and netiner receipt nor possession thereo! confers ar wasters any eight im or conse 10 use Ihe subject matter of tne drawing or any design or techeical information shown thereon. not any right to veproduce tis drawing er any part theteot. except for manutacture by vendors ol Atan incor orstedand for manutacture under the corporation s wit ten license no night © reproauce Ins drawing s granted or lhe subject matter thereat uniess by wren agresmant FI ‘ 8 be 2 ae [23 y3 | a2

al

Jalsa as “{P)8|3)a) gl slele ePeE ST Pr

DRIVE a

al Cres

Figure 5 Harness Schema Sheet 3 of 3 , Early Version

Page 27

NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the we written permission of Ataf, Inc. Sunnyvale forma This drawing 1S only conditionally sued. and her recep nor possession thereof confers or tansters ‘any night 9. of license to us® the subject matter of the raming oF any design or technical information shown thereon. norany right la reproduce tis drawing orany part thereot, except for manctacture by vendors of Atar’ incor porated ana far manufacture unde" the corporation $ wht. lon license, noright toraproduce his drawingts granted a the subject matier tneceo! qless By written agreement ~ with or written permission stom the corporation

ONT

Figure 5A Harness Schematic, Latest Version Sheet 1 of 3

Page 28

Sheet 2 of 3 Figure 5A Harness Schematic, Latest Version SOUND eA E |

weet 140, igi, 0, Uelgh ery

Page 29

NOTICE 10 ALL PERSONS RELEIVING THIS DRAWING. CONFIDENTIAL Reproduction torbigsen without the Specific written permission of Atari. In Caiitarma. This drawing 1s oly conettionaly ‘etthe: receipt nay possession thereo! confers or ansters

zyzthereon, norany right i@ rapraduce (ins Grawing ot ary part
aaGite craic rceuret esetn,
oO9the sutiect matter herent unlessby aritlon soreement
2dD‘nor mrven persion from the Corporation

x ¢ 0 ee

%4|is
3a6oRog
~a8OCapr&
izSo0FoBe
g4orlse
$9 P/@el|58h88
2i)cy5Foz
dheehalesy
HeZO2) |Ble38
“€1) a:a|
o)é%,2@
°A74st
asdi BECECMehmete

FED mb

Oletolio’aurs att fe solv ao. “2 care 4 oL.

Figure 5A Harness Schematic, Latest Version Sheet 3 of 3

Page 30

Figure 6 CONT 1 PCB Schematic To

conte

TOABLSI (N.C) P21 20]

ADI pt . TO

oi. " > +> t 7 | cow sw (N.0)

L

+4

cps) PHOTO =

Tl cet T9 18] cose ce ce cs s2av | ne _ w : cos be <1 seo Te]cgin Re To tS (acy F200 8S 119] ABLE! ss os

30 C0. se 3 coms SWE 2 coins

i RELAY n Be ae CON RL ge yo tay > ut

ners = a ba S + nol ep 7 rn Die x0 +—{I5] ceis(uoy

10, eo yeav —o Saal

GAME CONT 2 P-it,

START = 7 BRWE P-29 420, GSI SOUND P-2SESO i 8

u sev 8 Th Ter t {] oO wo/ 424y—» $s

os va Bondy $2 + Gs Fo = ests 14 REPLAY Sno 5 (wc) RP comme

i ° 13) To RPB. 22)

iit be Lig] 4 9 12

we | IN, cos = 23) score No 8 7 Pe

LINE AC

ENE o-—|39]4 r YouTMGE T37No°a CONNECTION °/ Re nd coms stone

"

teay ALDI ro if xo aeser sees BS] acciveNt motor. ea] SCORE j asl a TO rid oF B3] timer motor, © 2] ue

cps. Ze] To conte /owncnen une 10) To P28 AC VOLTAGE 2B] SOUND To. ores

+2avec[S[o} +24v 34] Lockour coin SWITCHED UWE Pogo fae] AC VOLTAGE win ano [1-4,29,30,43,44 RELAYS ACB) AGEN DENT

<i 1S cow

cz 28 COIN

eon COIN ACKEPTED,

cbe PHOTO cou

ast GAME START

RL RELLY

RP

REPLAY

TH TIMER,

WIN WIN trons the rorporation unless by writen agreement Ten ticense nongh Poratea ane tar manutacure und Subject mate htoreproguce mis drawings granted oF ‘ace ths Graming 6 facture by vengars of A thereon narary rghtte repro rainy oF any gesign OF Technical informatio any NghI im oF Wcense tO vse Ihe Subject mal Ihe writen permigeion of Atgn ine Cahora. This gaeing is only consihon Sunnyvale ally issues ang IDENTIAL Reprogucian lormagen withoul the NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

Page 31

ATARI O

4007421

Figure 6 CONT 1 PCB Drawing

ma y with or written permission trom the earpor

Page 32
ItemPart NumberQty.Description
1007422-011P.C. Board, Cont 1
219-815C3002Resistor 1 W, 30 OHMR1,2
324-5004761Cap Elect 47uf 50Vca
424--500337tCAP ELECT, 3d0Ouf , SOVC\
531-1N40011g | Dioée, 1N4001D1-18
643-900110 | Relay, 24V, 4 PDTCDS,WIN,C1,RP1,COIN,C2

7 ACD1,GS1,T1,RL

869-0011switch, Slide, DPDTsw

Lo =

Figure 6 CONT 1 PCB Parts List

Page 33

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL Reproduction forbidden without the

neither receigt nor possession Ihereo! conters ortransters, any right ear license 10 use. ths subject matter of the Graying oF any design of technical mfermatan shown Ineleom norany right fa reproduce his drawing or any 0a? tnereot except lar manulaclure by venders of Ate INGOT

JTS ExTeMOED

Wr fh

Figure 7, CONT 2 PCB Schematic

Page 34

Figure 7, CONT 2 PCB Drawing F-1 007423 CONT 2 ATARI O77

TT NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden withoul Ine en petmasion of Atar Inc Sunnysale oraming vs only canestionally sues ane nether receipt nor possessign thereat conters oF transters any ngnt oF Lcense fo use the subject matter of the framing oF any design ne teenoical informmanon shown thereon norany right toreproduce this gravang cr any part Inereol except tar manufacture by vendors o! Alam incor porate ard lor manutacture under tne corporation» writ Feniicunse no right te reproduce Mis eraying = granted or the sunject matter thereo! unless by wntten agreement with gr weniten germmsion trom tne Corboration

Page 35

Item Part Number Description

a aL 15, Vy 1s aL (007424-01 10-5101 10-5221 10-5102 10-5222 10-5472 10-5103 10-5223 10-5683, 10-5104 10-5474 19-825C6P8 19-311502 19-311103 19-311104 24-250106 24-250476 24-250227 24-250108 22 -102224 21-101334 27-250103 B.C. Ba, Control 2 Res, Car. Comp, ¥ W 5% 100 OHM nd " "220" ae "aa # ee "68K " see * 100% Res, Car. Comp, 4 W 5¢ 470K OHM 2W 5% 6.8 OHM

‘Trimpot 5K "10K "100K cap, Elect 1ouf 250 . "aque 25v “ 220u8 28 cap, Elect 1000uf 25v cap, Mylar, .22uf 100V cap, Mylar, .33ué lov cap Cer Disc .Oluf 25v R20, 35-37 R3,15 R4,8,16,18,32 RL,5-7,9, 10,22, 25,29,31,33 R23,24,30 R2,19 R17,34 13,28 R11/12,26,27 R14 R38 VR24 Ri VR3,5 e1 oy ci2 2,7 68, 10,13

Figure 7. CONT 2 PCB Parts List Part Number Description a Item 38, al a2 a7 4a 27-250104 3i-1N91g 3i-1Naoo1 3a-Mvso13 34-2N3704 34-203643 37-7400 A7-LM3L1H 37-555, 37-7805 43-4002 43-9001 78-06014 72-1406¢ 75-914c 75-054 38-6500 Henen cap Cer Disc. .luf 25v

Diode, 1N914 anaoo1 LED, Red MvS013 Transistor, 263704 ‘Transistor, 283643 1c, 7400 LL. Regulator F 7805, Relay, 24V, SPST Relay, 24¥, DPDT Heatsink (7805) Screw, Pan Ha, Phil, 4-40 x 3/8 La, Cres

Nut, Hex #4-40 Washer, Lock Int Star #4 Photo Isolater €3,6,11 Di 2-7 pa,9 21, 3-6,8 92.7 1c? 1¢2,5 103,4,6 acl cps ACD, TM, EF ACD 683

Page 36

%

Figure 8 DRIVE PCB Schematic

Page 37

VRS"

WASHER. we v4 J v HEAT SINK eon

vR4 sort FORWARD A007427_ FI DRIVE

SATRWARD

NOTICE TO ALL PERSONS RECEIVING ThIS DRAWING CONFIDENTIAL Reproduction forbueon wathoul the Specihe writen. permission of Alar Ini. Sunny Eanlaroa This diswing i= only conditionally issue nevlher receipl ner passessian thereat conte!’ any night it-or hcense to use the subject Malar Graming or any desion or technical mmformatian

the subject matter thereof unless by written aqreemen) teith Ge writen permvesion fram the corgoraton

Figure 8 DRIVE PCB Drawing

Ri

Page 38

a Item | Part Number | Qty. Description Tom | Part Number ] Quy. Description

Figure 8 DRIVE PCB Parts List 007428-01 P.C. Bd, Drive 2

10-5681 Res Car. Comp 4 W 5% 680 OHM R3L 28 19-311103 1 || Primpot 10K vR2

10-5102 ” . 1K” R40 “oe ” “2.2K RG, 26,39, 44,46, a a 2.7K R4,9,/14,19 so bs "3.3K 0° R34, 36,37 “oo ” "4.7K" R5,10,11,21,38 30 19-311503 3

names 10-5222 50K re 4,5

aL 32 23-250107 2 || cap, elect, loour, 25v 10,12 33 23350107 2 ” . 35v 4,8 34 24-250107 2 » : . 25v 12,13 35 27-250104 n “Cer Disc, -luf, 25V C1-3,6-9,15,17-19

10-5272 10-5332 10-5682 soe " 6.8K” R32

7 10-s47z 9 sw "75K" R33

10-5752 36 28-101101 1 "Dip Mica, 100pE 100v cle

10 10-5103 no . " 10K” R6,13,43,45 7 1101102 1 "pip Mica, 1000p£ 100 an 10-5153 3 28: ip Mic pf 10uv 14

12 10-5863 1 10-5104 14 10-5105, ” i 1sK R7 39 31-1N914 17 |] diode, 1914 D2-9,14-22

R30 " "100K" 12,35 40 31-1N4001 5 " an4oo1 D1b-13, 23

Res, Car. Comp. k W 5%, 1 Meg OHM R20 ar 34-2N4237 1 || transistor, 2n4237 10

as 14-1560 16 14-1680 17 14-1121, 1s 14-1151 Res, Film 4 W 1% 56 OHM R28 = ransistor, 1m 6 7 . ~ ee nit 42 34-2N22190, i ifm stor, 2N2219 of 2N3643 Q4, 12,12,14,16

3 34-203643 44 33-2N3644 45 34-2N3704 46 33-2N5355

an) “120” R29 " "150" Raz . . "KR R25, 2n3644 98,18 7 2N3704 05-7,13,15,17

19 14-1102 20 14-1222 2N5355 99 .C., uATAL ici-4

x“

ee eo! 7 7 "2.2 R22 47 37-741 48 37-7815

al 14-1153 22 14-1823 2 23 14-1154 2 7 ” "150K" 17,18 "15K R23 Regulator, F7815 REG 1

. “ "a2 15,16 49 37-79MG 50 43-4002 sl 43-9001 BATOMG REG 2 Relay sPsT, 24V RL1,3 Relay 4PDT, 24V 24,5

24 15-1561 “ “yw 18562 OHM Ral ae ae ea

25 19-811391 Res, Wirewound 1W 14 390 OHM R24 i 78-06015

  • 78-06014 Heatsink gio Heatsink REG 1

56 72- 1406C 87 75-9145 Screw, Mach, Fan Ha Phil, #4-40 x 3/8 CRES

Nut, Hex #4-40 Washer, Lock Internal Tooth #4

58 75-054

Page 39

fais) 3] any

Figure 9 SOUND PCB Schematic

Page 40

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL Reproduction forbidaen without the speeitic written permission of Alar inc Sunnyvale Callorma. This atawing i= only concihonalls sued and rerther receipt nor possession theleaf conlers ar iransters any sight in oF license 10 use the subject matter of the Graming or any design oF technical informatan shown thereon nor any rah ioroproduce ths drawing or

the subject matier thereol unless by wnmten agreement sti or writen permesion tram Ihe FoxParetion

OQ < fo “Zz <a a ae Ad b ¥ OSL ojo ofc k a

HEATSINK (70)

Ss 3 ae ra £z,305 § Peokary 552528 Grapneet 535553 eer eoo wo on Nd

Figure 9 SOUND PCB Drawing

Page 41

Figure 9 SOUND PCB Parts List =—— SS. <_< Description Part Number Description

Part Number 007426-01 L P.C. Board, Sound 38 27-250104 3 "Cer. Disc 0,luf 25V C7, 33,35 10-5100 1 || Res, car Comp, & Ww 58, 10 OHM R30 x9 | 28-101150 1 || % vipped Mica 1opf 190v 26 10-5560 2|,[" = « "56" Rae, 49 40 28-101101 1 Dipped Mica LOOpf 1oov car 10-5101 adi» ” 100 Raa a. 28-101471 2 "Dipped Mica 47op£ 100 27,34

10-5251, iso" R28 a2 28-101472 1 “Dipped Mica 4700p£ 100V 25

470" R12 re . " ik R32 44

20-5471 10-5102 10-5222 2.2K R33 45

ener oe 10-5472 es "4K" R1,2,13-19, 46 31-1No14 9 |} picde ines p1-9

29, 31,53 10 10-5682 6.0K 6647 a7 31-MP750 4 || Divae 750 pl0-13,

4 10-5103, 7 . now “1K R6,7,39,40, 48 41,43,45 49 3a-2n3643 12k R24 50 34-2N3704 ” "22K" 527,54 51 33-2N5355, " - 33K” R52 82 33-2N5193 15 10-5473 2 woe aK R10,42 2 34-2N6121

Le 10-8563 3 . Transistor, 2N3643 96 " 2N2704 91-4,7,9,10 2N5355 95 2N5193, Case 77-03 98 7 2n6121 ou . 26124 12

12 10-5123 1 Fey 10-5223, 2 . 1 10-5333 4 i "56K" RS, 11,38 54 33-2N6124

17 10-5104 lo ” . “100K” R8,9,21-23, 58 25, 34-37 57 37-7400 1 |] tec., 7400 tea 58 27-7404 1 "404 ica

le 10-5154 19 10-5224 "150K R3 " ” 220K” R26, 20 | 10-5334 aioe wn © 330K Ra i” to-sa7a 59 39-7492 1 "7492 1c6

22 49-8 19WP33 sow 470K R20 60 37-7493, 2 7493 acs

Res, Wirewound, 1 W 10%, 0.33 OHM RSO,51 eu in 29 | 19-317503 a |} pot, piush wee Sox vei aie 62 37-588 T.C., NES@O 1c9 26 19-311503 a |] pot, upright sox vRi-e " NESSS ace 63 M324 . 2 27 i931 104 1 |] Pot, upricht 100K vR2 S7HENS 2 L324 1c?

64 1

29 24250205 30 24-250476 Regulator +5V, 7805 102 65 7-7812 + = cap, Elect. luf 25v €2,4,16,19 ‘ sr7e Regulator +12V, 7812 11.

“ azug 25v 22 31 24-250107 " Loouf 25v 8, 31,92 68 79-3205 1 |] ruse folder

69 46-203102

  • 24-250227 33 24-250477 34 24-250228 35 21-101103 " " 220uf 25V as "© 470uf 25v 30 Fuse, 1 ANP FL

> 70 78-06015

. " 2200u£ 25V C28 ,29 1 {| Heatsink (nes4o) 7 0TeLO-O1 1 |] Heatsink (p11 & 912)

Mylar, .oluf 100¥ 2,12 © Myjar, 0-1uf 100¥ €3,5,6,9-11,15,17 Scr, Mach, Pan Hd Phil, 4-40 x 3/16 18, 20,23,24 73 ya-1alic 2 . yo pao x41 16

72 72-1403¢

36 21-101104 rt 37 | 27-250103 1 || * cer. vise vo1ut 25v cu 74 7806010 2 |] sit-paa «gir « 12)

5 95-090127 2 Shoulder Washer 44 (Teflon)

7 | 75-9140 2 || wat Hex 94-40 7 75-054 2 || Lock washer, tnt Star #4

Page 42

Figure 10 SCORE PCB Schematic

Page 43

LED .4 PL

39) |vs NTED ON CIRCUIT SIDE

WINdoW Py a + wo w

an < RAS Rae

ue 2N3704 x 4P I eo

a peta L |m

  • LED .4 P
  • winnow

= =a

LEDS

“= == Led Se Ea aes. NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction forbidgen wrtnout the TTivs arawing 18 only conditionally wesued. and cept noe possession thereet conters artransters any right 19 or license to use. the subject matter ot the Srawing oF any design ar technical infarmatan shawn, thereen.nacany night to reproduce this drawing r any part 16 and for manulactare under the corporation s wit lenticense.no nghtto reproduce thisdrawingis granted or the subject matter thereol unless ey wntlen agreement wilh or written permission trem the corporation

Figure 10 SCORE PCB Drawing

Page 44

Figure 10 SCORE PCB Parts List Item Part Number | Qty. Description Item Part Number Description

Pe eC) Ft 1, qs 2. 007430-01 10-5101 10-5102 10-5222 10-5472 10-5103 10-5153 10-5225 10-5104 12-5221 32-5271 24-250106 24~250107 21-101102 21-101473 27-250104 31-1N4001 31-1N914 34-283 704 33+2N5 355 37-4N28 P.c. Board, score Res, Car. Comp. 4 W 5% 100 OHM moon "aK oon oR ae "mm OR re aa "om 2K ook © "kw 58 220" "om yw 58 270 cap, Elect louf 25v Cap, Elect loouf 25v cap, Mylar .ooluf 100 Cap, Mylar .047uf 1loov cap, Cer Dise .luf 25

Diode, 1N4001 Diode, 1No14 Transistor, 2N3704 Transistor, 2N5355 .C., 4N28 R3,6,8 R36,39,42,45 RL, 16-19 0-12 R4,37,40,43,46 R2,7,13,15,20,47 R35,38,41,44 RO R14, R21-27 R28-34 6,7 cla ce-11 c12 €2,3,13-16 Di D2-4 as 96-9 1e2 al a2 37-7415132 37-1401 37-14025 37-14516B 37-140818 37-14001 37-14585 37-7447AN 37-7418170N 37-Tes001C 37-7805 43-4001 38-1720 38-1721 SOTTIS-01 OCTIT4-OF Sodan se 7418132 ~ 1401 14025 "145188 140818 "4001 " 145e5 ” 7447AN “— 7an8170N re5001¢ Regulator, F7805 Relay SPs? LED Display (GL-9R10 LED Display (GL-9R06 MASK, I" LED MASK, -u" LED 1c3 ica acs ace 1c7,13 ice 1c9 1clo,14 ici 1ci2 acl RL LEDI-4 LEDS-B

Page 45

Figure 11 Game Start Circuit Diagram

Page 46

Figure 12 Drive Block Diagram

Page 47

Figure 13 Accident Block Diagram

Page 48

Figure 14 Score Block Diagram

Page 49

Figure 15 Extended Play Block Diagram

Page 50

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 51

CALIBRATION

Calibration should be performed each time one of the following has been replaced:

  • Competition car motor
  • Racetrack motor
  • Control 2 PCB
  • Drive PCB The only special equipment necessary for this procedure is a stop watch and, if you desire (not absolutely necessary), a test panel. The calibration procedure requires two people without the test panel and only one person with the test panel. Figure 16 is a schematic diagram of the test panel. Before you attempt the calibration, perform the following procedure: 1, Remove CONT 1 PCB and set coin switch to 100 (1 coin) position, Reinstall CONT 1 PCB.
  • Measure AC line voltage, then set Voltage Selector at setting nearest to your line voltage (90, 100, 110, or 120 volts).
  • Measure AC voltage on screen projection lamp for 9.6 + 0.2 VAC.

Score calibration Perform the calibration procedure as follows;

  • Start F-1 game and stop watch simultaneously. Score panel will begin to increment 3.5 to 4.5 seconds (nominal 4 seconds) after game has started. This is adjustable by rotating VR1 TIMER on CONT 2 PCB.
  • Set shifter to LOW and accelerator to full acceleration. Start F-1 game. Score panel will increment to a score of 2800 to 3200 (nominal 3000) points during full game time. This is adjustable by rotating VR3 LOW on CONT 2 PCB.
NOTE: Steps 1 and 2 are both adjusted by VR2 on DRIVE PCB. You may have to play with the two speed adjustments to get step 2 within reason.
Page 52
  • Setshifter to LOW and accelerator to full acceleration. Start F-1 game. Soon after starting F-1, set shifter to HIGH and leave accelerator at full acceleration. Score panel will increment to a score of 7700 to 8300 (nominal 8000) points during full game time. This is adjustable by rotating VR5 HIGH on CONT 2 PCB

Main Car Calibration 1, Set shifter to LOW and accelerator to IDLE. Start F-1 game. After a few rotations, check that the time for one revolution of the racetrack is 6.5 to 7.5, seconds (7 nominal). This is adjustable by rotating VR2 COURSE SPEED on DRIVE PCB.

  • Set shifter to LOW and accelerator to full acceleration. Start F-1 game. Soon after starting F-1, set shifter to HIGH and leave acceleration at full acceleration. Wait 30 seconds, then check that time for one revolution of the racetrack is approximately 2.4 seconds. Competition Cars Calibration
NOTE: The following adjustments interact with VR8 TURNPOINT on DRIVE PCB. If adjustments of Steps 2 and 3 below are not possible, adjust VR8 TURNPOINT until all of the following steps are within reason.
  • Set shifter to LOW and accelerator to partial acceleration. Simultaneously start F-1 and stop watch. Competition cars will begin moving after approximately 3.9 seconds.
  • Check time that one of the competition cars takes to advance (in forward direction) one revolution. Time will be 40 to 44 seconds (nominal 42). This is adjustable by rotating VR4 FORWARD on DRIVE PCB.
  • Set shifter to LOW and accelerator to full acceleration. Start F-1 game. Check time that one of the competition cars takes to advance (in backward direction) one revolution. Time will be 10.0 to 10.6 seconds (nominal 10.3). This is adjustable by rotating VRS BACKWARD on DRIVE PCB.
  • Set shifter to LOW and accelerator to full acceleration. Simultaneously start F-1 game and stop watch. Immediately after game is started, set shifter to HIGH. Competition cars will begin moving backwards after approximately 3.1 seconds.

kockour 6 yysvac LAM

ano " oxo ” iL anaxe ”

FULLACCELERATION 16

Figure 16 Cockpit Simulator Test Panel Schematic

Page 53

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 54

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 55

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 56

ATARI Innovative leisure

ATARI INC. 1265 BORREGAS AVENUE SUNNYVALE, CALIFORNIA 94086 408/745-2000 e TELEX 35-7448 Av ees Oe ae