CATHODE RAY TOMES

Blueprint Parts and Operating Manual (Sep 1982)

Blue Print (Midway) (Zilec Electronics / Bally Midway, 1982) · Parts & Operating Manual · 98 pages · 53 sections · original scan

Page 1

September 1982 Game Nos. 300, 301 & 302

NO. 301 MINI

NO. 302 COCKTAIL

MIDWAY MFG. CO.

Nowsnd CenIatsY 10750 W. Grand Avenue Franklin Park, Illinois 60131 U.S.A.

Phone: (312) 451-1360 Cable Address: MIDCO _— Telex No.: 72-1596

Form No. 0300-00300-0000

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment Generates, Uses and can Radiate Radio Frequency Energy and if not installed and used in accordance with the Instructions Manual, may cause interference to Radio Communications. As temporarily permitted by Regulation it has not been tested for compliance to Subpart J or Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a Residential Area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

eae” BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

XP E.

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

CSelly MIDWAY

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497

© COPYRIGHT MCMLXXXII BY BALLY/MIDWAY MFG. CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

DESCRIPTION TABLE OF CONTENTS

Introduction .

Location and Setup Inspection ... 2-1 Installation 2-1 Self-Test ..... 2-4 2-4 2-4 Game Volume Adjustment Control Option Switch Settings

Game Operation Self-Test Mode . Attract Mode. Ready to Play Mode... Play Mode.........- High Score/tnitial Mode . Two Player Operation

Maintenance and Repair Cleaning 41 Fuse Replacement .. 4-4 Opening the Control Panel ... 4-2 Removal of the Main Display Glass 4-4 TV. Monitor Replacement........... 45 Printed Circuit Board Replacement 4-8 Opening the Attraction Panel .4-10

Illustrated Parts Breakdown Transformer Board Assy. — Parts List No. 300 — BLUEPRINT — Upright — Front... No. 300 — BLUEPRINT — Upright — Front arts : No. 300 — BLUEPRINT — Upright — Rear Access....... No. 300 BLUEPRINT Upright — Rear Access Parts List . No. 300 — BLUEPRINT — Upright — Header Fluorescent Light Assy. No. 300 — BLUEPRINT — Upright — Header Fluorescent Light Assy. — Parts List No. 301 — BLUEPRINT — Mini — Front............... No. 301 — BLUEPRINT — Mini — Front — Parts List No. 301 — BLUEPRINT — Mini — Rear Access........ No. 301 BLUEPRINT — Mini — Rear Access No. 302 — BLUEPRINT — Cocktail — Front.. No. 302 — BLUEPRINT — Cocktail — Front No. 302 — BLUEPRINT — Cocktail — Interior Access...... 5-14 No. 302 — BLUEPRINT — Cocktail — Interior Access — Parts List BLUEPRINT — All Versions — Card Rack Assy. — Parts List . BLUEPRINT — All Versions — Card Rack Assy. BLUEPRINT — Control Assy. .............. BLUEPRINT — Control Assy. — Parts List Filter Assy............068 Filter Assy. — Parts List . Front Door Assy. — U.S.A. 25¢ Front Door Assy. — U.S.A. 25¢ —

Page 4

TABLE OF CONTENTS (cont'd)

DESCRIPTION PAGE

vi.

Vil.

Vill. Technical Troubleshooting .............. 6. ccc cece eee een e ete e ete teen seen enn n es Introduction General Suggestions .. Harness Component Troubleshooting . Transformer and Line Voltage Problems A Glossary of Microprocessor Terms .. Introduction to the Z80 CPU...... General Purpose Registers . Arithmetic and Logic Unit (ALU) ... Instruction Register and CPU Control 280 CPU Pin Description fon} ?

2PORDDRDDRXROD hbRRRWWNHAAA

Coin Door Maintenance Metal Coin Acceptor Merchanisms . . Plastic Coin Acceptor Mechanisms. .

T.V. Monitor Manual Introduction ...... Symptom Diagnosis . Guide to Schematic Symbols . Troubleshooting..........+- Theory of Operation........ Differences Between Monitors Controls You May Not Touch . Parts Interchangeability ...... Wells Gardner Monitor Schematic — 19” ... Wells Gardner Monitor Replacement Parts List Electrohome Monitor Schematic — 19"..... Electrohome Monitor Replacement Parts List . Electrohome Monitor Schematic — 13”..... Electrohome Monitor Replacement Parts List . seth oo boadon+ Dor Dmrmrrrmnwnnnam

Schematics & Wiring Diagrams Wiring Diagram — Upright. . Wiring Diagram — Mini. Wiring Diagram — Cocktail . 70 VA Power Supply P.C.B. — Component Layout . 70 VA Power Supply P.C.B. — Schematic . Video P.C. Board — Component Layout Video P.C. Board — Schematic . MPU/Sound Board — Component Layou MPU/Sound Board — Schematic.......... Credit Multiplier P.C. Board — Component Layout. Credit Multiplier P.C. Board — Schematic ........... Credit Multiplier By-Pass P.C. Board — Component Layout . Credit Multiplier By-Pass P.C. Board — Schematic : eevvvve boNoOdhkOND4 covove oNis

Page 5

TABLE OF FIGURES

FIGURE PAGE

1-1. Assigned Point ValueS...... 06. cece cece nce cet en cence eee tenet eee eees 1-2 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies 2-2 2-2 Major Sub-Assemblies (Cont. from Fig. 2-1) . 12-3 2-3. Interlock Switch Operation .. 12-3 2-4 Game Volume Adjustment Control & Option Switch Location .2-4 2-5 Option Switch Settings . 12-5 3-1. Game Operation ... 3-1 4-1 Location of Fuses .. 4-41 4-2. Opening the Control Panel — Upright & Mini 14-2 4-3 Opening the Cocktail Game .............. 4-3 4-4. Removing the Control Panel — Cocktail . 4-3 4-5 Removal of Main Display Glass & T.V. Bezel — Upright 74-4 4-6 Removal of Main Display Glass & TV. Bezel — Mini . 4-4 4-7. Removing Top Glass — Cocktail ...........-..-..0- 14-5 4-8 Removing Monitor — Upright .. 4-6 4-9 Removing Monitor — Mini... 46 4-10 Opening the Cocktail Game . 4-7 4-11. Removing Monitor — Cocktail . 4-7 4-12 Replacing P.C.B.s — Upright. 4-8 4-13 Replacing P.C.B.s — Mini.. 4-8 4-14 Replacing P.C.B.s — Cocktail 49 4-15 Opening the Attraction Panel — Upright .4-10 4-16 Replacing Fluorescent Tube Starter — Upright 4-11 4-17 Opening the Attraction Panel — Mini......... .4-11 7-1 Removing and Replacing the Coin Acceptor . 7-1 7-2 Cleaning the Metal Coin Acceptor .... 17-2 7-3 Lubricating the Metal Coin Acceptor .7-2 7-4. Opening the Plastic Coin Acceptor... 7-3 7-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters .. 27-4

Page 6

Blueprint

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and Ii of this manual completely. It will not take more than a few minutes and it may be very heipful.

I. Introduction

BLUEPRINT is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCK- TAIL TABLE”. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to guide J.J. through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn. When playing this game, you must direct J.J. through the maze he is in. This is done with the control stick. J.J. is searching for the parts to build the Ammo Machine on the BLUEPRINT at the bottom of the screen which will enable him to save his girl friend from the ogre that is chasing her across the top of the screen. Each part of this Ammo Machine is contained in one of the houses in the maze. Two of the houses contain bombs. Also, any house that J.J. has removed a part of the Ammo Machine from will contain a bomb if he goes back into it forany reason. If J.J. goes into a house and comes out with a part for the Ammo Machine, he must tow it down to the BLUEPRINT and place this part over the corresponding section of the BLUEPRINT. This done, he can head back into the maze and go looking for another part to the Ammo Machine. If J.J. goes into a house and comes out with abomb, he must make his way to the Bomb Pit located at the lower right hand corner of the screen and throw it in BEFORE it goes off. If he fails, you lose one man. Once the Ammo Machine is built, J.J. must push the Start Button for it located at the lower left hand corner of the screen. Once this is done, the Ammo Machine will start firing at the ogre chasing J.J.’s girl friend across the top of the screen. You can move the Ammo. Machine back and forth across the bottom of the screen at this time with the control stick. It does not move up and down on the screen.

As your skill level increases, the ogre runs faster, the bomb fuses are shorter, a maze monster will appear (which can cause you to lose one man if you touch him), and so on. In general, each maze will be harder to complete than the one before. A bonus man is awarded to you as you reach or passa certain preselected point value. Each part of the Ammo Machine, the bombs, etc., have an assigned point value as listed in Figure 1-1.

Page 7

Game Objective

The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills and destroying as many of the ogres as you can.

As you do this, each succeeding rack will be harder to

complete.

OBJECT DESCRIPTION EACH PART OF AMMO MACHINE BOMB POINT VALUE 1000 POINTS 50 POINTS WEIRD WILLIE (BACK TO BOMB DISPOSAL PIT) 100 POINTS OGRE VARIABLE 25 TO 1000 POINTS

Figure 1-1 Assigned Point Values

1-2

Page 8

II. Location and Setup

INSPECTION:

  • Remove the game from its shipping crate.
  • Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? Q Any broken controls? O Any broken glass or plastic? OD Just look it over closely and make a note of any signs of damage.
  • Remove the shipping cleats from the bottom of the cabinet.
  • Install the four levelers, one at each corner of the cabinet. D Level the cabinet.
  • Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-1. O Also check to make sure all plug-in connectors on the wire harness are firmly seated.
NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up. O Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. Make sure all printed circuit boards (P.C.B.’s) are firmly seated in their connectors. These connectors are also keyed. The P.C.B.'s will only go into them one way without being damaged.
Note the location of the game's serial number. See Figure 2-1. Check all major subassemblies to be sure they are mounted securely. These are called out in Figures 2-1 & 2-2. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. + Power supply filter assembly. Transformer board assembly.
  • Make a note of any problems that can't be easily corrected.
  • Call your distributor and/or service man about your problem list.

2-1 INSTALLATION:

  • Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100° F (0° to 38° C) O Humidity: Not over 95% relative O Space required: Upright 25” x 35" (63cm x 88cm) Mini 20” x 24" (50cm x 60cm) Cocktail 32” x 22” (81cm x 55cm) O Game height: Upright 68" (170cm) Mini 61" (153cm) Cocktail 29” ( 73cm)
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. lf the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtaineda solution to this problem. Otherwise you could damage your game.
  • Interlock and power ON/OFF switches. See Figure 2-1. O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). When any access door is opened, the interlock switch installed there turns off all power to the game. Check each. interlock switch for Operation. proper
Page 9

SERIAL

POWER SUPPLY P.C.B. UPRIGHT

SERIAL NUMBER (MAY BE LOCATED. ON ANY CORNER)

CONTROL PANEL PLAYER 1

BOARDS

INTERLOCK SWITCH (INSIDE DOOR) SERIAL ON/OFF NUMBER SWITCH

POWER. SUPPLY P.C.B. INTERLOCK SWITCH

LoGic BOARDS

ON/OFF SWITCH

TRANSFORMER BOARD ASSY. (NOT SEEN)

Shticbsctadbat eda a aan

COCKTAIL TN. MONITOR

INTERLOCK SWITCH

Loaic BOARDS

  • TRANSFORMER BOARD ASSY. (NOT SEEN)

TRANSFORMER BOARD ASSY.

CONTROL PANEL PLAYER 2

POWER SUPPLY P.C.B. (NOT SHOWN)

ON/OFF SWITCH LOCATED UNDER TABLE ON PLAYER 2 SIDE

Figure 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies

2-2

Page 10

CONTROL

UPRIGHT

Figure 2-2 Major Sub-Assemblies (Cont. from Fig. 2-1)

After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 2-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. a If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-3.

Figure 2-3 Interlock Switch Operation

Page 11

SELF-TEST: Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or serviceman to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

GAME VOLUME ADJUSTMENT CONTROL: See Figure 2-4. The game volume control pots (MASTER VOLUME and BACKGROUND VOLUME) are located on the MPU/SOUND board. The other board is the VIDEO board. There are two pots. For adjustment, they may be reached through the rear access door on the UPRIGHT and MINI models. On the COCKTAIL TABLE models, you will have to open the table top to reach them. To make the sounds louder, turn the pots clockwise as you face them (77). To make the sounds less loud, turn the pots counterclockwise as you face them ( 4).

OPTION SWITCH SETTINGS: To change the option switch settings, you DO NOT have to take the MPU board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you do have to open the table top to reach them. When changing any options, ALWAYS put the game into the Self-Test mode, make your changes, check the results on the monitor screen, take the game out of the Self-Test mode, and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The option switch settings and what they will make the game do are shown in Figure 2-5. See Figure 2-4 for option switch locations.

VOLUME ADJUSTMENT OPTION SWITCH

Figure 2-4 Game Volume Adjustment Control & Option Switch Location

2-4

Page 12

BLUE PRINT

OPTION SWITCH SETTINGS

BONUS PLAYERS AWARDED: SW#1 SW#2 SW#3 SW#4 SW#5 SW#6 SW#7 SW#8

ONE MAN AT 20,000 POINTS.NOTONONNOT NOT
*ONE MAN AT 30,000 POINTS.USED OFFONUSED USED

ON OFF ONE MAN AT 40,000 POINTS

ONE MAN AT 50,000 POINTSOFFOFF

NORMAL / FREE PLAY

FREE PLAY *NORMAL PLAY

MAZE MONSTER:

*APPEARS IN 2ND MAZE APPEARS IN 3RD MAZE

COINS PER CREDIT

*1 COIN 1 CREDIT 2 COINS 1 CREDIT

DIP SWITCH 2

SW#1 SW#2 SW#3 SW#4 SW#5 SWH#6 SW#7 SW#8 PLAYERS PER CREDIT:

NOT NOT

2 MEN PER CREDITONONNOT
OFFONUSEDUSED USED

*3 MEN PER CREDIT 4 MEN PER CREDIT 5 MEN PER CREDIT

CABINET STYLE

UPRIGHT AND MINI MODELS COCKTAIL TABLE MODEL

DIFFICULT LEVEL SETTINGS

LEVEL 1 “LEVEL 2 LEVEL 3 LEVEL 4

*INDICATES FACTORY RECOMMENDED SETTINGS.

Figure 2-5 Option Switch Settings ON OFF OFF OFF

PART NO. M051-00300-A009 — REVISION B

2-5

Page 13

Ill. Game Operation

BLUEPRINT is a one or a two player game with a color T.V. monitor. The game gives a display which has all the parts shown in Figure 3-1.

PLAYER 1 SCORE

HIGH SCORE

GIRL

BLUEPRINT

REMAINING RUN TIME The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.

ke. —___“S _ HOUSES a CONTAINING BOMBS

ae . OR MACHINE PARTS

J.J. WITH MACHINE PART

BOMB/MONSTER PIT

CREDITS

Figure 3-1 Identification of “On Screen” Graphics During Play

SELF-TEST MODE The Self-Test mode is a special mode for checking game switches and computer functions. It is the. easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test will cause it to erase any CREDITS shown at the lower right corner of the screen from its memory. You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position. Next, turn the power to the game “OFF” and then back “ON” again. Now that the game is in the Self-Test mode, it will react as follows:
  • You will see two rows of numbers displayed on the monitor screen. Zero through three in the top row and four through seven in the bottom row. These numbers are in a white color. Directly below each of the white numbers is a pair of yellow numbers or Jetters and numbers together. The correct presentation for each of the tests (0 through 7)is giveh at the right.
  • If you see any presentation other than this exact one, something in your game is not functioning correctly. THE READINGS UNDER POSITIONS 5, 6 AND 7 can be disregarded because there is no ROM installed at these P.C. Board locations.

3-1

1ST SELF-TEST DISPLAY

ROM CHECK

0 1 2 56 = «10

Page 14

The table that follows shows the P.C. Board locations of all positions (0 through 7) given previously.

DESIGNATION M.P.U. P.C.B. LOCATION O

  • By pressing the 1 and 2 PLAYER BUTTONS at the same time, the game will go to the switch check portion of the Self-Test mode. When this is done, you should .see a display which looks like the following.

2ND SELF-TEST DISPLAY

PORT 0-BIT ;

PORT 1-BIT 0

DILSW1

SW2 DESIGNATION M.P.U. P.C.B. LOCATION 4 1s 5 NOT USED 6 NOT USED 7 NOT USED

. Moving the game switches and controls will cause the “1's” to change to “O's” and vice versa. A “0” means that particular switch is “ON” or in the CLOSED condition and a “1” means that particular switch is “OFF” or in the OPEN condition. If you move a switch or control on the game and it has no effect on the above display, the switch/button is either not working, miswired, or disconnected. Check it out thoroughly. . By pressing the 1 and 2 PLAYER BUTTONS at the same time, the game will go to the cross hatch pattern display of the Self-Test mode. This may be used for alignments and checks of various types. This pattern will remain sharp and clear for about 15 seconds and then it will change to a different rapidly changing one for about another 15 seconds as the game does a RAM check on itself. If all the RAMs check good, the cross hatch pattern will return and appear to fade in and out for ashort while as the game does a color check on itself before becoming sharp and clear again for another 15 seconds. This sequence continues to repeat itself until you decide to leave the Self-Test mode.

. If a bad RAM chip is found by the game's internal check system during the Self-Test, the game indicates this to you by displaying any of the below coded on the monitor screen. The following table shows which code translates to which RAM chip locations on the Video P.C. Boards.

BAD RAM LOCATION INFORMATION

SCREEN DISPLAY

0 DISPLAYED 1 DISPLAYED SCRATCH PAD RAM ERROR BACKGROUND C H ERROR 2 DISPLAYED 3 DISPLAYED

7 DISPLAYED ERROR DESCRIPTION

BACKGROUND ROW POSITION ERROR FAST MOVING OBJECT RAM ERROR

BACKGROUND COLOR RAM ERROR

3-2 CHECK VIDEO P.C.B. CHIP LOCATIONS

J1, K1, K2, J2, H2 B9, C7, C6, C9, C8, C10, F4, D6 D8, D9, D10, D11, B10, D7, B9 D15, D16, D14, E16, E15, E17, C18, B13, B12, A13, A12, D2 C11, C12, D12, D13, C9, C8, C10, F4, E14, BB

Page 15
  • When finished with the Self-Test mode, slide the Self-Test switch back to the “OFF” position, and turn the power to the game “OFF” and then back “ON” again.
  • Normal game functions will now return to the monitor screen.

ATTRACT MODE

  • The Attract mode starts: O Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) C After a Self-Test has been completed. (Performing a Self-Test sets the credits in the game's memory to zero “O”.) D After a play has been finished, the score was not high enough to put the game into the High Score/Initial mode, and there are no more credits left in the game’s memory. C After the High Score/Initial mode when there are no more credits left in its memory. C In the Attract mode, the game will give the following displays centered on the monitor screen:

Attract Mode Display 1 Attract Mode Display 2

THE THIRD DISPLAY IN THE ATTRACT MODE SEQUENCE SHOWS SIMULATED GAME PLAY

O The next display in the series lists the ten highest scoring individuals that have played the game to date.

No matter where the game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will hold this display on the monitor screen until the “1 PLAYER” or the “2 PLAYER” start button is pushed.

Page 16

Ready to Play Mode Display 1 READY-TO-PLAY MODE

  • The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game.
  • The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed.
  • In the Ready-To-Play mode, the game will give the above display centered on the monitor screen.
  • If no START button is pressed, the game will hold the above display on the screen indefinitely.

PLAY MODE The Play mode begins when either the “1 PLAYER” or the “2 PLAYER’ start button is pressed. The “READY- TO-PLAY MODE” display changes color, maze appears, “1 UP” flashes, J.J. appears, and play begins. The Play mode ends when all of your J.J.’s have had their hearts broken. When this happens, “GAME OVER’ is written across the top center of the monitor screen.

In this game, the ogre is chasing J.J.’s girl friend across the top of the monitor screen. And he’s catching up to her! The ONLY way J.J. can save her is to visit all the houses in the maze, collect all the parts needed, and construct the Ammo Machine shown in the BLUEPRINT at the bottom center of the monitor screen. An easy enough task you say — WRONG! Unfortunately for J.J. he has a number of obstacles to overcome, not to mention a time limit, before he will

3-4 Ready to Play Mode Display 2

be able to get the Ammo Machine completely built. Among these obstacles is the fact that two of the houses in the maze contain bombs instead of parts of the Ammo Machine. If he gets one of these, he must make his way to the bomb disposal pit at the lower right hand corner of the monitor screen BEFORE it explodes and throw it in. Also, if he enters any house that previously held a part for the Ammo Machine, he will come out with a bomb. This bomb must be thrown into the bomb disposal pit too. If any of the bombs explode BEFORE J.J. can throw them into the pit, you will lose one man. And if this is not enough, J.J. must accomplish all of the above while keeping an eye out for the KILLER FLOWER POTS. If he is so much as even slightly touched by one of these little devils, you will lose one man. And then there's Weird Willie. He’s a sort of cute little guy but he’s got a screw loose somewhere. | mean, what other reason could you think of for anyone setting up housekeeping in a bomb disposal pit?? At any rate, J.J.’s got to keep an eye out forhim. (Now you must understand that Weird Willie doesn't dislike J.J. It’s just that he has this odd sense of humor.) Ifhe gets out and J.J. allows him to run around the bottom of the screen, Weird Willie will eventually work his way over to the START BUTTON for the Ammo Machine and press it BEFORE itis complete. This will cause the unfinished Ammo Machine to fall apart. J.J. must grab Weird Willie and toss him back in his pit at the lower right hand corner of the screen. But Weird Willie is very persistent and will try it again sooner or later.

J.J. also has to remember not to touch that same START BUTTON before he completes construction

Page 17

of his Ammo Machine. It will fall apart just as fast and as surely if he touches it as it does when Weird Willie touches it.

Once the Ammo Machine is built, J.J. must push the START BUTTON for it (located at the lower left hand corner of the screen). Once this is done, the Ammo. Machine will start firing at the ogre chasing J.J.’s girl friend across the top of the screen. You can move the Ammo Machine back and forth across the bottom of the screen at this time by moving the control stick left or right. It does not move up and down on the screen. As your skill level increases and you get into the higher racks, the ogre runs faster, the bomb fuses are shorter, a maze monster will appear which can cause you to lose one man if you touch him (in which rack he appears is switch selectable), and you will lose first the far left exit from the maze and then the far right exit from the maze leaving only the center exit from the maze for all future racks. In general, each maze will be harder to complete than the one before. A bonus man is awarded to you as you reach or passa certain preselected point value (switch selectable).

WAYS IN WHICH YOU CAN LOSE A MAN (J.J.):

  • J.J. doesn’t make it to the bomb disposal pit with a bomb, it goes off before he gets there. J.J., complete with halo, ascends to heaven. Assuming you have at least one J.J. in reserve, nothing happens to the parts of the Ammo Machine that you've already assembled on the BLUEPRINT.
  • The ogre catches J.J.’s girl friend. J.J.’s heart breaks and complete with halo, he ascends to heaven. Assuming you have at least one J.J. in reserve, nothing happens to the parts of the Ammo Machine that you've already assembled on the BLUEPRINT.
  • In the later racks, if J.J. should touch the maze monster. Then, complete with halo, J.J. ascends to heaven. Assuming you have at least one J.J. in reserve, nothing happens to the parts of the Ammo Machine that you've already assembled on the BLUEPRINT.
  • Any time J.J. is touched by a Killer Flower Pot. Then, complete with halo, J.J. ascends to heaven. Assuming you have at least one J.J. in reserve, nothing happens to the parts of the Ammo Machine that you've already assembled on the BLUEPRINT. WHEN YOU LOSE YOUR LAST MAN (J.J.): When you loose your last J.J. GAME OVER PLAYER 1” is written across the top center of the mgnitor screen. At this point several different things can happen depending on whether or not your score was high enough to cause the game to go into the High Score/Initial mode. If your score was one of the ten highest of the day, the game will go into the High Score/Initial mode immediately. If your score is not high enough to cause the game to go into the High Score/Initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits lefts in its memory).

HIGH SCORE/INITIAL MODE In the High Score/Initial mode the game gives a display which looks like the following:

High Score/Initial Mode Display

When in the High Score/Initial mode, there is an “A” and two blank spaces displayed at the bottom center of the screen. By moving the controller stick to the right, the letter can be made to sequence forward through the alphabet: “A”, “B”, “C”, “D”, etc. By moving the controller stick to the left, the letter can be made to sequence backward through the alphabet: “2”, “Y", “X", “W", etc. When you reach your initial, release the controller and push the FAST button. Your initial is frozen in place and an “A” appears in the blank space next to your first initial at the same time. Select this and your last initial in the same manner as you did your first initial. If you do not wish to put your initials opposite your score, just press the FAST button three times. Three “A’”s will appear in the spaces at the bottom of the monitor screen where your initials would have gone. After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory). Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

Page 18

TWO PLAYER OPERATION The Upright, Mini, and Cocktail Table models all have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.

  • In the Upright and Mini models, the players must take turns at the controls.
  • In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when itis your turn. (When it is not your turn, your set of controls will have NO effect on the game.)
  • Your turn lasts until you lose one J.J. At this point, the game will do one of several things depending on whether or not the lost J.J. was your last or if you still have others remaining in reserve.

J.J. LOST — OTHERS STILL REMAINING IN RESERVE O J.J., complete with halo, ascends to heaven. O Next, the “RACK” changes to the “RACK” the other player is in, the “___ UP” flashes while what's left of the other player's Ammo Machine, his maze, and his J.J. appear on the monitor screen. O Play begins for the other player. JJ. LOST — NO OTHERS REMAINING IN RESERVE O Game displays “GAME OVER PLAYER __”. D J.J., complete with halo, ascends to heaven. O Next, the “RACK” changes to the “RACK” the other player is in, the “ UP” flashes while what's left of the other player's Ammo Machine, his maze, and his J.J. appear on the monitor screen. O Play begins for the other player. O After the last player's last J.J. is lost, the game displays “GAME OVER PLAYER _—” for him too. C If neither of your scores is high enough to cause the game to go into the High Score/Initial mode, the game will then either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory). O On the other hand, if one or both of your scores was high enough to cause the game to go into the High Score/Initial mode, the game will tell you this by giving a display like that shown previously. The number “1” or “2” is displayed where the blank space is to indicate which player should enter his initials at this time. O After you've entered your initials opposite your score(s), the game will then go to the list of high scorers after which it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).

3-6

Page 19

IV. Maintenance and Repair

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS.

The most important thing for you to remember is to play your game thoroughly EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. ONLY being familiar with and playing your game will inform you whether or not it is working the way it should.

The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis. CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging

FUSES ON TRANSFORMER BOARD & POWER SUPPLY BOARD damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.

FUSE REPLACEMENT This game contains several fuses located as shown in Figure 4-1.

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Transformer and Power Supply Board Assemblies.
  • MIN! MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Transformer and Power Supply Board Assemblies.
  • COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Transformer and Power Supply Board Assemblies. ’ Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.

Figure 4-1 Location of Fuses

Page 20

OPENING THE CONTROL PANEL

1, UPRIGHT MODEL: See Figure 4-2. 0 The control panel is held in place by three

  • MINI MODEL: See Figure 4-2. 0 The control panel is held in place by two latches, latches, one on the left side, one on the right side, and one on the front center. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind ‘it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. To reinstall the control panel, reverse this procedure. one on the right side, and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. To reinstall the control panel, reverse this procedure.

UPRIGHT

Figure 4-2 Opening the Control Panel — Upright & Mini

4-2

Page 21

Figure 4-3 Opening the Cocktail Game

  • COCKTAIL TABLE MODEL: See Figure 4-4. C Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 4-3.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor.

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-3.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 4-4, O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed.

O To reinstall the contro! panel, reverse this procedure. LIFT CONTROL UP

REMOVE

  • SCREWS EACH SIDE

Figure 4-4 Removing the Control Panel — Cocktail

Page 22

REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY 1, UPRIGHT MODEL: See Figure 4-5.

NOTE: In order to do this, the control panel MUST be removed first. See the “UPRIGHT MODEL” procedure. O Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted off. By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed.

To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure. o

DISPLAY GLASS

GLASS CLAMPS

Figure 4-5 Removal of Main Display Glass & T.V. Bezel — Upright

4-4

  • MINI MODEL: See Figure 4-6.
NOTE: In order to do this, the contro! panel MUST be removed first. See the “MINI MODEL” procedure. O Turn the power off to the game and remove the control panel. O Remove the screws which secure the glass clamping plate. Q Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out.

O Remove the screws which secure the T.V. bezel assembly and lift it out.

NOTE: Use the hole in the center of the maindisplay-glass support to grasp it. O Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.

DISPLAY GLASS

GLASS CLAMPING PLATE

Figure 4-6 Removal of Main Display Glass & T.V. Bezel — Mini

Page 23
  • COCKTAIL TABLE MODEL: See Figure 4-7.
NOTE: This may be done with the table top in the open or the closed position. If you decide to

open the table top, TURN THE POWER TO THE

GAME OFF FIRST. 1 Remove the screws which secure the table top glass clamps in place. CO Remove the table top glass. Gi Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed. O To reinstall the T.V. bezel assembly and the table top glass, reverse this procedure.

Figure 4-7 Removing Top Glass — Cocktail

4-5 T.V. MONITOR REPLACEMENT

CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In- addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your! hands on the metal T.V. chassis without such protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing

the monitor on a test bench, YOU MUST ISOLATE

THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.

  • UPRIGHT MODEL: See Figure 4-8. O Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. To reinstall the T.V. monitor, reverse this procedure. After replacing the T.V. monitor, be sure to run the game Self-Test.
  • MINI MODEL: See Figure 4-9. O Turn the power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Mini Model” procedure. With the removal of only four nuts, the T.V. monitor will be loose.
CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet.
Page 24

The monitor is removed by supporting it and Open the coin box door and release the two pulling straight back. latches indicated in Figure 4-10. QO To reinstall the T.V. monitor, reverse this procedure. CAUTION: The right hand latch is very close to After replacing the T.V. monitor, be sure to run the HIGH VOLTAGE on the monitor. the game Self-Test. O Once the latches are released, unhook them from their latch plates.

  • COCKTAIL TABLE MODEL: See Figure 4-11. O Grasp the table top at “A” and open it as O Turn the power off to the game. indicated in Figure 4-10.

REMOVE (4) BOLTS REMOVE (4) BOLTS

Figure 4-8 Removing Monitor — Upright Figure 4-9 Removing Monitor — Mini

Page 25

CLAMPS

Figure 4-10 Opening the Cocktail Game

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet. REMOVE 6 SCREWS (3 EACH SIDE) O Remove the screws which hold the table top glass clamps in place. O Remove the table top glass. D Lift out the T.V. bezel assembly. 0 Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 4-11. 0 Close the Cocktail Table and re-latch it.

O Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 4-11. O Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. Q Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL not to bump the neck of the picture tube. ; ; ~ REMOVE 4 SCREWS

O To reinstall the T.V. monitor assembly, reverse (2 EACH SIDE)

this procedure. O Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game Self-Test. Figure 4-11 Removing Monitor — Cocktail

4-7

Page 26

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

  • UPRIGHT MODEL: See Figure 4-12. a

Q

Q

Qo

oOo

Qo

ia) Turn the power to the game off.

Unlock and open the rear access door (game board) and the coin door (sound board). Disconnect the game board from all its cabling. Disconnect the sound board fromall its cabling. Remove the indicated P.C.B. supports and lift the above P.C.B.’s out the cabinet.

Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-12, and slide it out the back of the cabinet.

To reinstall the above P.C.B.’s, reverse this procedure.

REMOVE BRKT. REMOVE SUPPORT (NOT SHOWN) (NOT SHOWN) AND LIFT AND SLIDE P.C.B. ASSEMBLY OUT OUT OF CABINET OF CABINET

Figure 4-12 Replacing P.C.B.s — Upright

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.

. MINI MODEL: See Figure 4-13. C Turn the power off to the game.

O Unlock and open the rear access door.

O Disconnect the game board from all its cabling. 0 Disconnect the sound board from allits cabling. O Remove the indicated P.C.B. supports and lift the above P.C.B.’s out of the cabinet.

0 Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-13, and slide it out the back of the cabinet. O To reinstall the above P.C.B.’s, reverse this procedure.

REMOVE BRKT. (NOT SHOWN) REMOVE SUPPORT AND LIFT (NOT SHOWN) ASSEMBLY AND SLIDE P.C.B. OUT OF OUT OF CABINET CABINET

Figure 4-13 Replacing P.C.B.s — Mini

Page 27

REMOVE (2) REMOVE BRKT. = SUPPORTS AND (NOT SHOWN) f : LIFT P.C.B. AND LIFT ASSEMBLY ¢ (NOT SHOWN) OUT OF CABINET OUT OF CABINET)

Figure 4-14 Replacing P.C.B.s — Cocktail

  • COCKTAIL TABLE MODEL: See Figure 4-14. O Turn the power off to the game. O To remove the power supply board. See Figure O Open the cabinet: 414, Open the coin box door and release the two Disconnect it from all its cabling. latches indicated in Figure 4-10. Remove the two smallest P.C.B. supports. Once these are removed, the power supply can
CAUTION: The right hand latch is very close to be lifted out the top of the cabinet. the HIGH VOLTAGE on the monitor. To reinstall the power supply board, reverse this procedure. Once they're released, unhook them from their (0 To remove the game and sound boards. See latch plates. . Figure 4-14. O Grasp the table top at “A” and open it as Disconnect the game board from all its cabling. indicated in Figure 4-10. Disconnect the sound board fromall its cabling.

O Remove the indicated P.C.B. supports and lift the above P.C.B.’s out of the cabinet. To reinstall the game and sound boards, reverse this procedure.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.
Page 28

OPENING THE ATTRACTION PANEL Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and

  • UPRIGHT MODEL: See Figure 4-15. femove iitom fe aoeeee q O Turn the power to the game off. To replace the fluorescent light tube starter, O Opening the attraction panel: reverse this procedure. Remove the screws which secure the top O Replacement of the fluorescent tube mounting bracket in place. (They are on its top side.) bracket assembly. Remove the top bracket and slide up the attrac- Be sure the power is off to the game. tion panel. This exposes the attraction panel * Disconnect it from its power cable. fluorescent light tube and its mounting bracket Remove the screws which secure it and gently

assembly. slide it out of the front of the cabinet, being Procedure. To reinstall the fluorescent tube mounting

To reinstall the attraction panel, reverse this careful not to catch its power cable on anything.

O The fluorescent light tube may be replaced at bracket assembly, reverse this procedure. this time. BE CAREFUL NOT TO DROP IT. 1 Replacing the speaker.

Be sure the power is off to the game.

WARNING: If you drop a fluorescent tube and it Remove the attraction panel and disconnect the breaks, IT WILL IMPLODE! Shattered glass can speaker from its cabling. fly six (6) feet or more from the implosion. Use Remove the nuts and bolts which secure the care when replacing any fluorescent tube. speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in O Replacing the fluorescent tube starter, See place are removed, the speaker may be Figue 4-16. removed through the opening where the attrac- Be sure the power to the game has been tion panel was. turned off. Reverse this procedure to reinstall the speaker.

_¢-—— REMOVE SCREWS & LIFT ATTRACTION PANEL UP

Page 29

eo™

4 TURN TO REPLACE FLUORESCENT

Figure 4-16 Replacing Fluorescent Tube Starter — Upright

2, MINI MODEL. See Figure 4-17. Slide the speaker out through the rear ac- O Turn the power off to the game. —_ door. , . To reinstall the speaker, simply reverse O Remove the screws which secure the top this procedure. bracket in place. (They are on its top side.) . 3. THE COCKTAIL TABLE MODEL HAS NO BACK- Remove the top bracket and slide up the attrac- LIT ATTRACTION PANEL. tion panel. This exposes the attraction panel light bulbs and their mounting board. O To service the light bulbs and their mounting REMOVE SCREWS & board: LIFT ATTRACTION Turn the power to the game back on so you can PANEL UP see which bulbs are burnt out. Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reyerse this procedure. O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Figure 4-17 Opening the Attraction Panel — Mini

Page 30

V Illustrated Parts Breakdown

BLUEPRINT — TRANSFORMER BOARD ASSEMBLY — NO PHOTOGRAPH

ORDER BY PART NUMBER ONLY

DESCRIPTION

POWER TRANSFORMER — 120/240V. (UPRIGHT & MINI) TRANSFORMER (UPRIGHT & MINI) SHIELDED TRANSFORMER — 115/120V (COCKTAIL ONLY) TRANSFORMER W/MAGNETIC SHIELD (COCKTAIL ONLY) 1 POSITION FUSE CLIP ASSY. (MINI ONLY) 2 POSITION FUSE CLIP ASSY. (ALL) 3 POSITION FUSE CLIP ASSY. (UPRIGHT & COCKTAIL) 1/2A., 250V. SLO-BLO FUSE (1 REQ’D. — UPRIGHT & COCKTAIL) 2A., 250V. SLO-BLO FUSE (2 REQ’D. — UPRIGHT, 3 REQ’D. — MINI & COCKTAIL) 3/4A., 250V. SLO-BLO FUSE (1 REQ’D. — UPRIGHT) 2-1/2A., 250V. SLO-BLO FUSE (1 REQ’D. — UPRIGHT, COCKTAIL & MINI) 2 POSITION TERMINAL STRIP 115V. CONVENIENCE OUTLET ASSY. 2 LEAD TRANSFORMER BOARD FILTER ASSY. LINE CORD CABLE ASSY. GROUNDING CLIP (2 REQ’D.) 5-1/2" LG. — GROUND STRAP (UPRIGHT & COCKTAIL) 48" LG. — GROUND STRAP (UPRIGHT ONLY) GROUND STRAP (COCKTAIL ONLY) GROUND STRAP (MINI ONLY) 36” LG. — GROUND STRAP (MINI ONLY) ITEM PART NO.

MT00-00087-0000 MT00-00092-0000 MTO00-00091 -0000 MTO00-00093-0000 0720-00001-0100 0720-00001-0200 0720-00001-0300 0017-00003-0002 0017-00003-0004

0017-00003-0177 0017-00003-0217

0017-00021-0634 A151-00079-0000 A508-00037-0000 A089-00014-0000 3010-03003-0000 3000-17246-0500 3000-17246-0900 3000-17246-0300 3000-17246-0200 3000-17246- 1000

5-1

Page 31

5-2 NO. 300 — BLUEPRINT — UPRIGHT — FRONT

Page 32

NO. 300 — BLUEPRINT — UPRIGHT — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

0300-00901 -00XF HEADER DISPLAY PLEX! 595-0001 11-0000 HEADER LIGHT ASSY. 0537-00903-0058 GLASS CHANNEL — 6-15/16”" LG. (2 REQ'D.) 0574-00903-0100 HEADER BRKT. RETAINER (2 REQ’D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER PROOF PAN HD. SCR. (6 REQ’D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) 0017-00003-0430 6" x 9" SPEAKER — 4 OHM, 10W. 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS 0017-00101-0127 #8-32 x 1-1/2" CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) 0508-00900-0000 19” T.V. BEZEL 0300-00900-00XF MAIN VIEWING GLASS 0508-00108-0000 GLASS STOP BRKT. (CABINET REAR) 0017-00101-0027 #8 x 3/4 SLT. HEX HD. M.S. (3 REQ’D.) 0300-00902-0000 CONTROL SHELF OVERLAY — DECORATIVE A300-00015-0000 CONTROL SHELF PLATE ASSY. — WELDED 0982-00102-00XF STRIKE (2 REQ’D.) 0017-00009-0033 LATCH CLAMP (3 REQ’D.) 0550-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0550-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901 -0000 PLASTIC LOCATING PIN (4 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. MS. (6 REQ’D.) A300-00021-0000 8-POSITION CONTROL ASSY. A300-00013-0000 CONTROL SHELF CABLE ASSY. 0017-00042-0304 RED — PUSH BUTTON ASSY. (2 REQ'’D.) 0017-00042-0260 WHITE — PUSH BUTTON ASSY. (2 REQ'D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (4 REQ’D.) 0017-00103-0054 5/8-11 PAL NUT (4 REQ'D.) 0300-00904-0000 FRONT DECAL 0300-00903-0100 SIDE DECAL — LEFT 0300-00903-0200 SIDE DECAL — RIGHT A090-00300-11BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A982-00015-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0100 KICK PLATE — 23" LG. 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.)

5-3

Page 33

5-4 NO. 300 — BLUEPRINT — UPRIGHT — REAR ACCESS

Page 34

NO. 300 — BLUEPRINT — UPRIGHT — REAR ACCESS — PARTS LIST

A088-00013-0000 0894-00916-0000 0017-00101-0141 0017-00003-0339

0017-00003-0439

0508-00102-0000 0595-00104-0000 0017-00102-0066 0017-00104-0014 0555-00901-0000 0866-00120-0000 0017-00101-0141 0508-00108-0000 0508-00900-0000 A088-00015-0000 A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0950-00103-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A0Q82-90427-A000 0624-00902-0100 0624-00902-0500 0017-00101-0141 0017-00104-0037 A300-00004-0000 A300-00006-0000 A089-00014-0000 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037

A082-91109-A000 A151-00098-0000 0017-00009-0490 A300-00018-0000 A300-00007-0000 A300-00008-0000 A300-00010-0000 A515-00020-0000 3000-17246-0700 3000-17246-0800 ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

ON-OFF SWITCH & BRKT. ASSY. RECESSED HAND PULL & VENT (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR MTG. CHANNEL (2 REQ’D.) MONITOR RAIL (2 REQ’D.) 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (4 REQ'D.) 7/8" DISH WASHER (4 REQ’D.) PLASTIC LOCATING PIN (4 REQ’D.) CHASSIS BRACE #8 x 11/16 UNSLOT. HEX HD. M.S. (4 REQ’D.) GLASS STOP BRACKET 19" T.V. BEZEL INTERLOCK SWITCH & BRKT. ASSY. COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ’D.) LARGE PLASTIC COIN BOX COIN BOX DIVIDER — OPTIONAL 1/4-20 x 1-3/8 BLK. RND. HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ'D.) POWER SUPPLY BOARD ASSY. P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 6-1/2” LG. (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (10 REQ’D.) #8 WASHER (10 REQ’D.) CARD RACK W/BOARDS ASSY. TRANSFORMER BOARD ASSY. LINE CORD CABLE ASSY. CASTER ASSY. (2 REQ'D.) WHEEL BRKT. (2 REQ’D.) PLASTIC WHEEL (2 REQ’D.) SHAFT (2 REQ'D.) 3/8" E-RING (2 REQ'D.) ADDITIONAL PARTS LIST CREDIT MULT. BYPASS P.C.B. BACK DOOR LOCK ASSY. 5-5/8" SQR. VENT GRILL — BACK DOOR (4 REQ’D.) MASTER CABLE W/BRKT. ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. VIDEO SIGNAL CABLE ASSY. TEST SWITCH & BRKT. ASSY. 20" GROUND STRAP — CONTROL SHELF 23” GROUND STRAP — CONTROL SHELF

5-5

Page 35

NO. 300 — BLUEPRINT — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY.

Page 36

NO. 300 — BLUEPRINT — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0595-00105-0000 FLUORESCENT BRKT. 0017-00003-0043 18” COOL WHITE FLUORESCENT LAMP 0017-00003-0445 LAMP LOCKS (2 REQ'’D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ'D.) 0017-00003-0412 FLUORESCENT STARTER HOLDER W/LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ'D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00003-0019 FLUORESCENT STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) A961-00042-0000 LINE FILTER ASSY.

5-7

Page 37

Bests oo .

  • FRONT NO. 301 — BLUEPRINT — MINI

5-8

Page 38

NO. 301 — BLUEPRINT — MINI — FRONT — PARTS LIST

0301-00901-00XF 0537-00903-0062 0574-00903-0200 0017-00101-0138 0017-00009-0522 A574-00007-0000 0017-00031-0030 0017-00003-0219 A574-00015-0000 0017-00009-0393 0017-00003-0259 0017-00101-0127 0017-00103-0061 0301-00900-00XF 0537-00903-0056 A555-00016-0000 0017-00101-0138 0513-00900-0000 A961-00026-0000 0301-00902-0000 A301-00015-0000 0555-00101-0100 0550-00101-0200 0550-00901-0000 0017-00009-0033 0017-00101-0141 A300-00021-0000 A301-00009-0000 0017-00042-0260 0017-00042-0304 0017-00032-0093 0017-00103-0054 A090-00300-11BK A982-00015-0000 0090-00002-04BK 0017-00101-0121

0935-00906-0400 0017-00102-0048 0017-00103-0026 ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

DISPLAY HEADER GLASS CHANNEL — 3-7/8" LG. (2 REQ’D.) HEADER RETAINER BRKT. (2 REQ’D.) #8 x 5/8 TORX TAMPER RESISTANT SCR. (8 REQ’D.) LONG ARM KEY T-20 (FOR ABOVE SCREW) INSERT DISPLAY ASSY. WEDGE BASE LAMP SOCKET (5 REQ’D.) #194 LAMP — 14V., .27A. (5 REQ’D.) INSERT DISPLAY CABLE ASSY. BLACK SPEAKER GRILL W/SLOTS 6" x 9" SPEAKER — 8 OHM, 7W. #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) MAIN VIEWING GLASS GLASS CHANNEL — 14-1/2" LG. (2 REQ’D.) GLASS CLAMPING PLATE ASSY. #8 x 5/8 TORX TAMPER RESISTANT SCREW (2 REQ’D.) TV. BEZEL BEZEL MTG. BRKT. ASSY. (2 REQ’D.) CONTROL SHELF OVERLAY — DECORATIVE CONTROL SHELF PLATE WELD ASSY. CONTROL SHELF MTG. BRKT. — RIGHT CONTROL SHELF MTG. BRKT. — LEFT PLASTIC LOCATING PINS (4 REQ’D.) LATCH CLAMP (2 REQ'’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) 8-POSITION CONTROL ASSY. CONTROL SHELF CABLE ASSY. PUSH BUTTON ASSY. — WHITE (2 REQ’D.) PUSH BUTTON ASSY. — RED (2 REQ’D.) PUSH BUTTON SWITCH W/HOLDER (4 REQ'D.) 5/8-11 PAL NUT (4 REQ'D.) 25¢ U.S.A. DOUBLE COIN DOOR ASSY. COIN DOOR CABLE ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) KICK PLATE — 17-15/16" LG. 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

5-9

Page 39

5-10 NO. 301 — BLUEPRINT — MINI — REAR ACCESS

Page 40

NO. 301 — BLUEPRINT — MINI — REAR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

6" x 9” SPEAKER — 8 OHM, 7W. ELECTROHOME — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR T.V. MTG. BRKT. ASSY. 1/4-20 x 3/4 UNSLOT. HEX HD. BOLT (2 REQ’D.) 7/8" DISH WASHER (2 REQ’D.) 1/4-20 HEX NUT (2 REQ'D.) MONITOR MTG. BRKT. INTERLOCK SWITCH & BRKT. ASSY. 25¢ U.S.A. DOUBLE COIN DOOR ASSY. COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE LARGE PLASTIC CASH BOX COIN DEFLECTOR (2 REQ’D.) COIN BOX DIVIDER — OPTIONAL 1/4-20 1-3/8 BLK. RND. HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ’D.) POWER SUPPLY BOARD ASSY. P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 6-1/2" LG. (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (10 REQ'D.) #8 FLAT WASHER (10 REQ’D.) CARD RACK W/BOARDS ASSY. TRANSFORMER BOARD ASSY. ON-OFF SWITCH & BRKT. ASSY. LINE CORD CABLE ASSY. ADDITIONAL PARTS LIST

CREDIT MULT. BYPASS P.C.B. BACK DOOR LOCK ASSY. 5-5/8" SQR. VENT GRILL (4 REQ'’D.) PROTECTIVE BUBBLE — BACK DOOR #8-32 x 3/4 CARRIAGE BOLT (10 REQ’D.) #8-32 HEX NUT W/SEMS (10 REQ’D.) TEST SWITCH & BRKT. ASSY. MASTER CABLE W/BRKT. ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. VIDEO SIGNAL CABLE ASSY. 0017-00003-0259 0017-00003-0340

0017-00003-0435

A926-00012-00XF 0017-00102-0066 0017-00104-0014 0017-00103-0018 0513-00101-0000 A088-00015-0000 A090-00300-11BK A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00900-0000 0950-00101-00XF 0950-00103-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A082-90427-A000 0624-00902-0100 0624-00902-0500 0017-00101-0141 0017-00104-0037 A300-00004-0000 A301-00005-0000 A088-00013-0000 A089-00014-0000

A082-91109-A000 A151-00098-0000 0017-00009-0490 0926-00904-0000 0017-00101-0628 0017-00103-0061 A515-00020-0000 A301-00014-0000 A301-00006-0000 A301-00007-0000 A300-00010-0000

5-11

Page 41

5-12 NO. 302 — BLUEPRINT — COCKTAIL — FRONT

Page 42

NO. 302 — BLUEPRINT — COCKTAIL — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

COVER GLASS — 32” x 22” x 1/4" ARTWORK UNDERLAY GLASS CLIPS (8 REQ’D.) #8 x 5/8 BLK. PHIL. TRS. HD. SCR. (16 REQ’D.) T.V. BEZEL BEZEL MTG. BRKT. (2 REQ’D.) ACRYLIC DIFFUSER CONTROL SHELF ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF ASSY. — PLAYER #2 CONTROL SHELF CABLE ASSY. — PLAYER #2 BLACK SPEAKER GRILL W/SLOTS (3 REQ’D.) 6" x 9” SPEAKER — 8 OHM, 9W. #8-32 x 1-1/4 CARRIAGE BOLT (12 REQ’D.) #8-32 HEX NUT W/SEMS (12 REQ’D.) 25¢ U.S.A. DOUBLE COIN DOOR ASSY. COIN DOOR CABLE ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCREW (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 3/8-16 LEG LEVELER HE NUTS (4 REQ’D.) 0017-00009-0499 0302-00900-0000 0775-00104-O0XF 0017-00101-0117 0557-00900-0000 0508-00106-0000 0530-00903-0000 A302-00009-0100 A302-00010-0100 A302-00009-0200 A302-00010-0200 0017-00009-0393 0017-00003-0187 0017-00101-0136 0017-00103-0061 A090-00300-11BK A982-00015-0000 0090-00002-02BK 0017-00101-0121

0017-00102-0048 0017-00103-0026

5-13

Page 43

NO. 302 — BLUEPRINT — COCKTAIL — INTERIOR ACCESS

anes

Page 44

NO. 302 — BLUEPRINT — COCKTAIL — INTERIOR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR MONITOR SUPPORT ASSY. — LEFT MONITOR SUPPORT ASSY. — RIGHT #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ'D.) STRIKE (2 REQ’D.) #10 x 3/4 SLT. HEX HD. M.S. (4 REQ’D.) LATCH CLAMP (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. SCREW (4 REQ'D.) SUPPORT ANGLE (2 REQ’D.) #8-32 x 5/16 SLT. HEX HD. M.S. (8 REQ’D.) 2-1/2" HINGE (2 REQ’D.) #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) CONTROL PANEL ASSY. — WELDMENT (2 REQ'D.) DECORATIVE OVERLAY PLAYER #1 DECORATIVE OVERLAY PLAYER #2 #6 x 1/4 PHIL. TRS. HD. SCR. (6 REQ’D.) BOTTOM PAN (2 REQ’D.) 8-POSITION CONTROL ASSY. (2 REQ’D.) CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2 RED — PUSH BUTTON ASSY. (2 REQ’D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ'D.) 5/8-11 PAL NUT (2 REQ'D.) SMALL RED BUTTON SWITCH (2 REQ'D.) PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2 SLT. HD. SCREW (12 REQ’D.) LIGHT SHIELD (2 REQ’D.) WEDGE BASE LAMP SOCKET (4 REQ’D.) #194 LAMP — 14V., .27A. (4 REQ'D.) #6-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) 6" x 9" SPEAKER — 8 OHM, 9W. ITEM

0017-00003-0439

A515-00019-0000 A515-00019-0100 0017-00101-0109 0610-00132-00ZN 0017-00101-0769 0017-00009-0033 0017-00101-0141 0927-00101-00XF 0017-00101-0598 0017-00009-0514 0017-00101-0136 0017-00103-0061 A302-00015-0000 0302-00901-0100 0302-00901-0200 0017-00101-0341 0510-00101-00XF A300-00021-0000 A302-00010-0100 A302-00010-0200 0017-00042-0304 0017-00032-0093 0017-00103-0054 0017-00032-0051 0930-00104-0000 0017-00101-0025 0930-00904-0000 0017-00031-0044 0017-00003-0219 0017-00101-0555 0017-00003-0187 A775-00013-0000 FAN ASSY. 0151-00081-0000 4” FAN 0775-00110-00XF FAN PLATE 0749-00106-00XF FAN SCREEN FAN CABLE ASSY. #6-32 x 1/2 RND. HD. M.S. (4 REQ’D.) #6 EXT. WASHER (4 REQ’D.) #6-32 HEX NUT (4 REQ’D.) #8 x 5/8 SLT. HEX HD. SCREW (4 REQ’D.) TRANSFORMER BOARD ASSY. CARD RACK ASSY. W/BOARDS POWER SUPPLY BOARD ASSY. — NOT SHOWN P.C. SUPPORT BRKT. — 12” LG. P.C. SUPPORT BRKT. — 2-1/2" LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 6-1/2" LG. #8 x 11/16 UNSLOT. HEX HD. M.S. (10 REQ’D.) #8 FLAT WASHER (10 REQ’D.) A775-00018-0000 0017-00101-0347 0017-00104-0009 0017-00103-0005 0017-00101-0026 A302-00006-0000 A300-00004-0000 A082-90427-A000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0141 0017-00104-0037

5-15

Page 45

NO. 302 — BLUEPRINT — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

| item | PART NO. DESCRIPTION ADDITIONAL PARTS LIST

A082-91109-A000 CREDIT MULT. BYPASS P.C.B. A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY. A088-00014-0000 INTERLOCK SWITCH & BRKT. ASSY. A515-00020-0000 TEST SWITCH & BRKT. ASSY. A927-00019-0000 COIN BOX ASSY. A962-00004-0000 COIN BOX COVER ASSY. A962-00005-0000 COIN BOX SIDE CHANNEL ASSY. — SHORT 0962-00101-0000 COIN BOX SIDE CHANNEL — SHORT 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00104-0022 #8 WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ'D.) A302-00012-0000 MASTER CABLE W/BRKT. ASSY. A302-00007-0000 HIGH VOLTAGE CABLE ASSY. A302-00008-0000 LOW VOLTAGE CABLE ASSY. A300-00010-0000 VIDEO SIGNAL CABLE ASSY. 0927-00907-0000 FORMED HIGH VOLTAGE SHIELD A927-00005-0000 HIGH BASE LEG KIT ASSY. — OPTIONAL

BLUEPRINT — ALL VERSIONS — CARD RACK ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

DESCRIPTION

MPU/SOUND BOARD ASSY. VIDEO BOARD ASSY. HOLDER PLATE & STOP ASSV. (2 REQ’D.) NYLON GUIDE (4 REQ’D.) RETAINER (2 REQ’D.) SIDE SUPPORT (2 REQ'’D.) MOUNTING BRACKET (2 REQ’D.) #6 x 3/8 SLT. HEX HD. SCR. (14 REQ’D.) PART NO.

A084-91430-C300 A084-91431-A300 A935-00015-0000 0017-00009-0478 0935-00105-0000 0935-00103-0000 0935-00102-0000 0017-00101-0096 ITEM ONADawWN= A

Page 46

BLUEPRINT — ALL VERSIONS — CARD RACK ASSY.

5-17

Page 47

BLUEPRINT — CONTROL ASSY.

5-18

Page 48

BLUEPRINT — CONTROL ASSY. — PARTS LIST

PART NO. DESCRIPTION

A932-00022-0000 BALL & SHAFT ASSEMBLY 0017-00100-0025 1/4" E-RING 0921-00702-0000 STOP SPACER 0530-00907-0000 SLIDE PLATE A982-00019-0000 PIVOT PLATE WELD ASSY. 0017-00101-0637 #8-32 x 1" CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0932-00902-0000 GROMMET 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. M.S. (10 REQ’D.) 0962-00904-0000 SLEEVE 0017-00101-0527 #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) 0020-00202-0000 SWITCH PLATE (4 REQ’D.) A932-00009-0000 SWITCH ASSEMBLY (4 REQ'D.) A921-00009-0000 STOP PLATE & SWITCH BRKT. ASSY. 0927-00908-0000 WEAR PLATE 0921-00700-0000 ACTUATOR ORDER BY PART NUMBER ONLY

OHMBNADAANMA=

5-19

Page 49

“ASSV Y3L14

Page 50

FILTER ASSY. — PARTS LIST ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0945-00101-00XF 0945-00803-0100 0945-0080370200 0945-00100-0000 0017-00101-0555 0017-00021-0539 0017-00101-0510 0017-00104-0087 0017-00104-0071 0017-00103-0002 0062-122H7-1XXX 0062-086H7-1XXX

0017-00003-0008 0017-00003-0174 0017-00003-0433 0017-00041-0008 A089-00007-0000 A089-00006-0000 0945-00804-0100 0017-00103-0086 0017-00021-0484 0017-00104-0107 0017-00009-0510 0017-00042-0283 0945-00900-0000 CHASSIS CAPACITOR — 55000MF — 25V. CAPACITOR — 100000MF — 15V. CAPACITOR STRAP. #6-32 x 5/16 SLT. HEX HD. SCR. (4 REQ'D.) 5 POSITION TERMINAL STRIP (2 REQ'D.) #4-40 x 1/2 SLT. PAN HD. SCR. (4 REQ'D.) #4 FLAT WASHER (4 REQ'D.) #4 EXT. TOOTH WASHER (4 REQ'D.) #4-40 HEX NUT (4 REQ'D.) RESISTOR — 150 OHM, 2W. RESISTOR — 47 OHM, 2W. — LOCATED ON OPPOSITE TERMINAL STRIP FUSE — 6 AMP — 120V. FUSE — 10 AMP — 32V. FUSE HOLDER (2 REQ'D.) RUBBER GROMMET FILTER CABLE ASSY. #2 FILTER CABLE ASSY. #1 DIODE — 12A. — 50V. (4 REQ'D.) #10-32 HEX NUT (4 REQ'D.) SOLDER LUG (4 REQ'D.) #10 FLAT WASHER (4 REQ'D.) INSULATOR (8 REQ'D.) BUSHING (4 REQ’D.) DIODE FORMED FISHPAPER COVER — NOT SHOWN

Page 51

FRONT DOOR ASSEMBLY

5-22

Page 52

FRONT DOOR ASSEMBLY — U.S.A. 25¢

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0090-00002-02BK DOUBLE ENTRY COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) A090-00073-02BK DOUBLE ENTRY COIN DOOR W/DRESS PLATE 0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCREW (12 REQ’D.) 0017-00007-0019 KEY HOOK 0017-00101-0552 #6-32 x 1/4 CARRIAGE BOLT (4 REQ'D.) 0090-00117-03XF COIN ENTRY PLATE — 25¢ (2 REQ’D.) A097-00005-0000 DOOR LOCK & KEY W/SCREW & NUT (OR) A097-00006-0000 DOOR LOCK & KEY W/SCREW & NUT 0090-00128-00XF DOOR TILT SWITCH BRKT. 0017-00005-0041 DOOR CAM A090-00095-0000 DOOR TILT SWITCH 0090-00126-01XF SWITCH BACK-UP PLATE 0017-00101-0525 #5-40 x 9/16" PHIL. HD. M.S. (2 REQ'D.) A090-00096-0000 DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 0090-00903-9500 25¢ WINDOW (2 REQ'’D.) 0090-00143-00XF COIN PLEX RETAINER 0017-00003-0219 12 VOLT LAMP — G.E. #194 (2 REQ’D.) 0017-00031-0048 WEDGE SOCKET W/BRKT. (2 REQ’D.) A090-00100-0000 BRKT. ASSY. 0017-00103-0084 #6-32 HEX NUT W/SEMS (4 REQ'D.) A090-00089-0000 COIN METER W/DIODE 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. SCR. (4 REQ’D.) A090-00087-0000 COIN CHUTE & TOP ASSY. (2 REQ’D.) CWBMNONDAONH

0010-00134-0000 SPRING 0010-00181-0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN 0090-00129-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0093-00155-00XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 A090-00105-0000 0017-00005-0003 0017-00005-0211 0017-00005-0214 A090-00064-0000 0017-00101-0099 0090-00162-00XF 0017-00005-0203 REJECT LEVER ASSY. (2 REQ’D.) (ITEMS 30 THRU 33) COIN ACCEPTOR FRAME ASSV. (2 REQ’D.) COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) (OR) COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ’D.) (OR) COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) ANTI-PENNY DEVICE #6 x 1/4 SLT. HEX HD. MS. (2 REQ'D.) COIN SWITCH MTG. BRKT. COIN SWITCH CHUTE 0017-00005-0195 COIN SWITCH 0010-00599-0000 COIN SWITCH WIRE 0017-00007-0132 PUSH-ON RING A090-00059-0400 0017-00101-0147 A090-00077-0000 COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) #4-40 x 3/4 PHIL. PAN. HD. M.S. (2 REQ’D.) COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)

5-23

Page 53

VI Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the citcuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet.

After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). lf the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 54

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary

some from game to game, but no game’will work on

line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 55

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM’s contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LS! “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:

  • The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory .
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose 1/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic. 2.

3.

Page 56

General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the regiSters and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)

Subtract Increment

Logical AND Decrement Logieal OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

oe —a -——-— A, waco 2] —— Aa

SYSTEMora 2]LB. a
CONTROLS—2u
ROwe—
wh22]———e

36 A

aFSH28|} > a,

| 38 a ADDRESS

mat=Z-80 CPU[a

p40 a,

  • 24 1 iT An
cpuwari

CONTROL [> #s nt = —8 a} [——» A,

ami7p+ a,
aeee26pa,

RESET ————* site 25 CPU BUSRQ ———*) BUS susak «2 CONTROL byt Do ee» v, 6 12

0_——_=> D,
+5V—a DsDATA
cup— |jee v,BUS

3 D;

13 ms Z-80 PIN CONFIGURATION =O

6-4

Page 57

Ao-Ais (Address Bus) Tri-state output, active high. Ap-A,5 constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. !/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ao is the least significant address bit. During’ refresh time, the lower 7 bits contain a valid refresh address.

D,-D, (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

M, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle.

MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 10RQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid 1/O address for al/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) _ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.

6-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.

INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664, The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WATT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 58
  • Set Register | = 00x
  • Set Register R =00n
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.

CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements. ee oooooanuUnququuooeeeeeEEyEyElIlLl——————_—_—_=aas

Page 59

VII. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers, Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: Metal and Plastic mechanisms: COIN MECHANISMS, INC. COINCO COIN ACCEPTORS, INC. 817 Industrial Drive 860 Eagle Drive Elmhurst, IL 60126 Bensenville, IL 60106 Phone (312) 279-9150 Phone (312) 766-6781

COIN DOOR MAINTENANCE

  • Remove the coin acceptor mechanism as shown METAL COIN ACCEPTOR MECHANISMS in Figure 7-1. Periodically, the metal coin acceptor mechanism(s) Qo Push down On the two spring loaded latches. must be removed from the coin door and cleaned. While holding the latches down, pull the top of the coin acceptor mechanism toward you. € Release the latches and lift out the coin accep-
  • Unlock and open the coin door. tor mechanism.
  • Make sure the power to the game is off.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS PULL MECHANISM OUT PUSH MECHANISM IN TO REPLACE

Figure 7-1 Removing and replacing coin acceptor

7-1

Page 60
  • Clean the magnet of all foreign particles. See Figure 7-2. O This may be accomplished by swinging the gate open as shown in the above figure.
  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) O Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.
  • To lubricate the coin acceptor: 0 Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
  • WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
CAUTION: BE CAREFUL NOT TO BURN YOU! SELF. 8. Check the coin chute for obstructions such as:

O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. C Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 7-2 Cleaning the metal coin acceptor paper, gum, etc.

  • Reinstall the coin acceptor to the coin door. See Figure 7-1 0 Place the two pegs at the coin acceptor's base into their retaining slots. 0 Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

UNDERSIZE LEVER

CRADLE

Figure 7-3 Lubricating the metal coin acceptor

7-2

Page 61

SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 7-4 Opening the plastic coin acceptor

PLASTIC COIN ACCEPTOR MECHANISMS

The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanism(s) as shown in Figure 7-1. Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. O Release the latches and lift out the mechanism.
  • Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.

7-3 D Reassemble the mechanism (it never needs lubrication).

  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 7-5. O Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 7-6 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.
Page 62

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

ee

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.

7-4

Page 63

PLEASE NOTE:

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

1F YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Page 64

Color T.V.

Color T.V Monitor

Introduction: (How to use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

8-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 65

Symptom Diagnosis

. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. 0 Bad vertical output section. O Open fusible resistor in vertical section. O Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). O Bad yoke. 0 Open width coil. O Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control, Focus voltage wire not connected to neckboard terminal. . Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. B.

. Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking contro! set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).

8-2 10.

11.

12.

13.

14,

15.

16.

17.

18.

19.

20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.

Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A). B. Vertical oscillator is not putting out the right wave form.

Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.

Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.

No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).

No brightness, high voltage present; check: A. Heater voitage to the tube at the neck board. B. Screen-grid voltage for tne tube. C. Focus voltage. D. Grid to cathode picture tube bias.

No high voltage; check: A. For AC input to the “flyback”. B. Horizontal deflection stages. C. Flyback transformer. D. Yoke. E. Power supply.

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack trom logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 66

21.

22.

23. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).

Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.

Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

  • Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interferring. —. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SV W INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

{-) CATHODE

(+) ANODE

ZENER DIODE

8-3 IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

Ls

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 67

COLLECTOR a COLLECTOR oo

BASE ————> BASE————> EMITTER ee EMITTER caret

NPN TRANSISTOR PNP TRANSISTOR

WWW

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+ +

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

og & GROUND

8-4

Page 68

Troubleshooting

Troubleshooting monitors requires experience, patience, and tuck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection, This will pinpoint the circuit the problem is probabiy in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits), Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT. itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,060 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first itimplodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground, Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the ancde hole. Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smalier the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very gaAwN

8-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It's better to be too careful than dead, which is why electronic equipment aiways carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggies when handling the picture tube.

To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor On a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate contro! that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the controi itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of syrnptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schemaiic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possibie offenders,

Page 69

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ahms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. !f it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by ‘heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voitage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usuaily be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows acharging action. As they suck up Current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wail outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electroiytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. tf the voltage from the power supply is too low, the other circuits wil! be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the piace where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 70

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a, Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information wili be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or osciilates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roli up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the verticai amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor iike this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycies a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn’t going at the correct speed, the picture may move sideways, Start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the osciliators up and down. This way you have controls ‘that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving ina car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn't appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizonta! yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The flyback transformer receives current alternating at about 15.750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON !T AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.

COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The coior output circuits are on the neck board. The color signais going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green.

Page 71

The blue doesn’t have one. In the emitter part ofeach transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's 1C501 and emitter of X04 for the Electrohome monitor. Here are the voltages you shouid receive: Wells Gardner = 130VDC Electrohome 120VDC The best piace to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO07-FBO or G07-902, has an integrated circuit and very littie else in the power supply. Still, there should be 120VDC at B1.

THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode.

After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen, Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with, assuming you can’t find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Wells Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let's say you have an Electrohome that isn’t working. No problem. You can scavenge parts from an old broken up one that you may have around.

Now let’s say you have a Wells Gardner that isn't working. STOP! This could bea problem. There are3.

8-8 different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical! Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the

Page 72

screen. Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Control EXCEPT the picture tube is vertically mounted and there is an additional small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move apy control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark onthe knob. If you moveit, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier. You CANNOT swap any picture tubes between monitors!i In the past you could, but Wells Gardner is now using a new monitor. When

8-9 ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is evena19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE! You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.

Page 73

Power Supply Voltage and Symbols T Symbol / Voltage Operating Circuit

® 15Y Vert. Osc. Sync Blanking CRT Cut-Oft

e | 130 Horiz. Osc. Horz. Drive Horz. Output Vert. Output © 175V Video Output

JVIDIV 200uSECIDIV

TP-31 DC COUPLED BOTTOM LINE=0 VDC

2V/DIV 200MSECIDIV

1.C. 301, PIN 3

1VIDIV SMSECIDIY

TP82

20VIDIV SMSECIDIV

1.0. 301, PIN 19

‘1WDiv 200uSEC/DIV 951 COLLECTOR

20VIDIV 10uSECIDIV

94023

SVIDIV 20uSECIDIV

F

Peri

1W/DIY 20u SEC/DIV

‘TP-31, AG COUPLED

1VIDIV 200uSECIDIV

NEGATIVE SIDE OF C303

2VIDIV SMSECIDIV 19” COLOR MONITOR SCHEMATIC DIAGRAM

MODELS 19K4901, 19K4906, 19K4951, 19K4956

SERVICE TECHNICIAN WARNING X-RAY RADIATION PRECAUTION:

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM- PONENTS ONLY WITH MANUFAC. TURER'S RECOMMENDED PARTS. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE ITE DE L'APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR RES PIECES RECOMMANDEES PAR LE FABRICANT. THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS ESSENTIAL FOR X-RAY RADIATION PROTECTION FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN iN THE

LIST

MO

9.401 RED OUT 9.402 GREEN OUT OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilioscope with the monitor turned to a reasonably Strong signal and a normal picture. The voltages shown on each waveform are the approximate peak amplitudes. if the waveforms are observed on the oscilloscope with a poor high frequency response, the corner of the pulses wil! tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.

RP Bur a 2ECZ06a.B/88K 2SC208ELE/ Box 25¢2068L 8/.29k | ] BSCISIsEve/eVe ZSCIBI4BVCKVC 2SCiSeavC/Cve e |

Rais ark were)

O.SIDIV SMSECIDIV arktnev2)

O.SIDIV 20u SECIDIV

nay by Ne uae) CME Rass HOR. DRIVE te Tmt! 2acessaan oP. S] esc6i0ex 1G. 307, PIN 15,

R301 are

SYNC AMP WOSe HOS HANia23 é

ay pease Tr03 % 'se076.

fe case? spcs08 $ w505 "320 Paine, 2 ee Ee : ” a DEGAUSSINO COIL 1VDIV 2MSECIDIV

  • K4901D, K4906D, K49510 5833 K4956B 'g 10
Page 74

Rel. No.

R201 R202 R203 R204 R205 R206 R267 R208, R209 R210 R211 R214 R215 R216 R217 R218 R219 R220 R221 R222 R224 R225 R226 R227 R228 R229 A230 R231 R232 R233 R234 R235 R236 R301 R302 R303 R304 R305 R306 R307 R309 R310 R311 R312 R313 R314 R315 R316 R3i7 R318 R319 R320 R321 R322 R351 R352 R363 R354 R255 R368

R361 R362 R363 R364 R365, R367 R368 REPLACEMENT PARTS LIST

This monitor contains circuits and components included specifically for safety purposes. For continued protection no changes should be made to the original design, and components shown in shaded areas of schematic, or A %« on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation or other hazard. Service should be performed by qualified personnel only.

MAIN BOARD

Part No.DescriptionRef. No.Part No.Description

»SISTO RESISTORS (CONT)

203X8500-645,MC Ohm5%, AVR369203x5602-329680K Ohin, 5%, 1/2W Comp.
203X6500-52330 Ohm,6%, 1/4W CarbonR370203X6501-00233K Ohm, 5%, 1/4W Carbon
203X8500-405100 Ohm, 5%, 1/4W CarvonR371203X9014-5841K Ohm, 5%, 1W Metal Oxide
203X6700-327100 Ohm, 5%, 1/2W CarbonR372203X3101-11942K Ohm, 8%, 1W Metal Oxide
203X6700-421270 Ohm, 5%, 1/2W CarbonR375,203X6700-7836.BK Ohm, 8%, 1/2W Carbon
203X6500540390 Ohm, 5%, 1/4W CarbonR376203X9104-404270 Ohm, 5%, 2W Metal Oxide
340X2201-834200 Ohm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon
203X6500-540390 Ohm, 5%, 1/4W CarbonR378203X8500-88610K Ohm, 5%, 1/4W Carbon
340X2201-934200 Ohm, 5%, ‘/4W CarbonR379203X6500-88610K Ohm, 5%, 1/4W Carbon
203X6500-540390 Ohm, 5%, 1/4W €arbonF380203X6500-8658.2K Ohm. 5%, 1/4W Carbon
340X2201-934200 Ohm, 5%, 1/4W CarbonR381203X6500-7242.2K Ohm, 5%,1W Metai Oxide
203X6500-6451K Ohm, 5%, 1/4W CarbonR383,203X9014-387150 Ohm, 5%, 1Wv Metal Oxide
203X6501-126400K Ohm, 5%, 1/4W CarbonR502203X6500-88810K Ohm, 5%, 1/4W Carbon
203X6500-645,1K Ohm, 5%, 1/4W CarbonR503204X1700-535150 Ohm, 5%, 15W Metal Oxide
203X6500-405100 Ohm, 5%, 1/4W CarbonR504203X9014.26747 Ohm, 5%, 1W Metal Oxide
203X6500-645,1k Ohm, 5%, 1/4W CarbonR505,203X6501-2092.2K Ohm, 5%, 1/4W Carbon
203X6501-126100K Ohm, 5%, 1/4W CarbonR506203X9104-10515 Ohm, 5%, 2W Metal Oxide
203X6500-645,1K Ohm, 5%, 1/4W Carbon507203X5602-185,330K Ohm, 5%, 1/2W Comp.
203X6500-405,100 Ohm, 5%, 1/4W CarbonAKREO1204X 1625-0583.3 Ohm, 5%, 10W WW
203X6500-7623.3 Ohm, 5%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2W Metal Oxide
203X6500-16910 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%, 1/2W Carbon
203X6500-16940 Ohm, 5%, 1/4W CarbonR201204x2070-0722K Ohm-B Semi-Fixed
203X6500-169,40 Ohm, 5%, 1/4W CarbonR301204X2070-0845K Ohm-B Semi-Fixed
203X6501-04447K Ohm, 5%, 1/4W CarbonVR303204X2070-055500 Ohm-B Semi-Fixed
203X6500-6451K Ohm, 5%, 1/4W CarbonVR351204x2070-0722K Ohm-B Semi-Fixed
203X6700-421270 Ohm, 5%, 1/2W CarbonR352204x2070-0722K Ohm. Semi-Fixed

203X6500-863, B.2K Ohm, 5%, 1/2W Comp. 203X6500-863, 8.2K Ohm, 5%, 1/2W Comp. 203X6500-863, 8.2K Ohm, 5%, 1/2W Comp. 203X6500-468 180 Ohm, 5%, 1/4W Carbon 340X2820-934 82 Ohm, 5%, 1/4W Carbon CAPACITORS

340X2820-93482 Ohm, 5%, 1/4W Carbon201203x0014-0881000 uF, 16V, Electrolytic
340X2820-03482 Ohm, 5%, 1/4W Carbon202202X7200-064330 pF, 500V, Ceramic
203X6500-508270 Ohm,5%, 1/4W CarbonC203202X7200-043220 pF, 500V, Ceramic
203X6500-863,8.2K Ohm, 5%, 1/4W Carbon204202X7200-043220 pF. 500V, Ceramic
203X6500-8638.2K Ohm, 5%, 1/4W Carbon205203X0014-076470 uF, 16V, Electrolytic
203X6500-7242.2K Ohm, 5%, 1/4W CarbonC206203X1810-1490.1 uF, 125V Mylar
203X6500-8426.8K Ohm, 5%, 1/4W CarbonC207349X2232-109022 uF, 100V Mylar
203X6003-2017.5K Ohm, 2%, 1/4W CarbonC301203X0014-065,330 uF, 50V Electrolytic
203X6500:8255.6K Ohm, 5%, 1/4W Carbon302203X 1600-5630.083 UF, 50V Mylar
203X6500-96522K Ohm, 5%,1/4W Carbon303203X0629-0373.3 uF, 50V Electrolytic
203X6500-98839K Ohm, 5%, 1/4W Carbon304203x1600-3660.068 pF, 50V Mylar
203X6500-7623.3K Ohm, 5%, 1/4W Carbon306203X0412-0122.2 uF, 18V Tantal
203X9014-7444.7K Ohm, 5%, 1/4W Carbon307203X 1600-6340.033 uF, 50V Mylar
204X1450-5371K Ohm, 5%, SW Carbon308203X0025-1743.3 uF, 50V Electrolytic
203X6500-481220 Ohm, 5%, 1/4W CarbonC309203X1207-1000.068 UF, 100V PP
203X6500-16910 Ohm, 5%, 1/4W CarbonC310203X0629-06110 uF, 100V Electrolytic
203X6500-7623.3K Ohm, 5%, 1/4W Carbon314203X0041-02510 uF, 160V Electrolytic
203X6700-10712 Ohm, 5%, 1/2W CarbonC312202X7050-2481000 pF, 500V Ceramic
203X6500-540390 Ohm, 5%, 1/4W Carbon313203X0040-05247 uF, 160V Electrolytic
203X6500-6451K Ohm, 5%, 1/4W Carbon6314203X1201-2650.033 uF, 200V PP
203X6501-00233K Ohm, 5%, 1/4W Carbon315203X0629-023,1 uF, 50V Electrolytic
203X8501-224270K Ohm, 5%, 1/2W Carbon0351203x0629-0231 UF, 50V Electrolytic
203X6500-88610K Ohm, 5%, 1/4W CarbonC352203X0619-04547 uF, 25V Electrolytic
203X6500-88610K Ohm, 5%, 1/4W CarbonC353203x 1190-0150.0082 pF, 50V Mylar-PP
203X6500-7853.9K Ohm, 5%, 1/4W CarbonC354203X0619-04547 uF, 25V Electrolytic
203X6501-08568K Ohm, 5%, 1/4W CarbonC355203X 1600-3660.0068 pF, SOV Mylar
203X6500-7623.3K Ohm, 5%, 1/4W CarbonC356202X7050-483,0.01 uF, 500V Ceramic
203X9205-143,6.8K Ohm, 5%, 3W Metal OxideC359202X8065-606100 pF, 500V Ceramic
203X5601-87856K Ohm, 5%, 1/2W CarbonC360202X7050-2660.0033 pF, 500V Ceramic
203X6500-561470 Ohm, 5%, 1/4W CarbonC361202X7050-4830.01 uF, 500V Ceramic
203X6500-88610K Ohm, 5%, 1/4W CarbonC362202X7203-0320.01 uF, 50V Ceramic
203X9014-6451.8K Ohm, 5%, 1W Metal OxideA¥0363203X1270-9118700 pF, 1.5 KV PP
204X1527-7513.9K Ohm, 5%, 7W Metal OxideC365203X 1201-2650.33 uF, 200V PP
203X6500-24622 Ohm, 5%, 1/4W CarbonC386203X0019-02622 uF, 25V Electrolytic
203X6501-00233K Ohm, 5%, 1/4W CarbonC367202X8065-1626 pF, 500V Ceramic
203X6500-88610K Ohm, 5%, t/4W CarbonC368202X7203-0320.01 uF, 50V Ceramic
203X5602-185330K Ohm, 5%, 1/2W Comp.372203x1207-125,0.1 uF. 100V PP

8-11

Page 75

MAIN BOARD(CONT.)

Ret. No.Fart No.DescriptionRel. No.art No.Description

CAPACITORS (CONT) SEMICONDUCTORS (CONT.}

380202X7200-087470 uF, S00V Ceramic208200X3181-523Transistor (NPN) 2S61815GR
ACSI203X1810-1490.1 uF, 125V Mylar207200X3181-523Transistor (NPN) 2SC1815GR
4 0502202X7050-2821500 pF, 500V Cerantic208200X3181-523Transistor (NPN) 2SC1815GiA
4 6603202K7810-2142200 pF, 128V Ceramic209200X3181-523Transistor (NPN) 2SC1851GR
Ac504202X7810-2142200 pF, 125V Ceramic210200x3181-523,Transistor (NPN) 2SC1851GR
505203X0220-075560 uF, 200V ElectrolyticQ30t200X3181-523Transistor (NPN) 2SC1851GR
os08208X0040.03422 uF, 160V Electrolytic2302200X3207-308Transistor (NPN) 2SC2073LBGL2
cs07203X0061.05747 uF, 160V Electrolytic9303200x3207-306Transistor (NPN) 28C2073LBGL2
C701203X00:9.0921000 UF, 25V Electrolytic9361200X3248-217Transistor (NPN) 2SC2482BK
C702203X0634-06110 uF, 100V ElectrolyticQ352200X4589-802Transistor (NPN) 2SD808B
C703202X7050-248,1000 pF, 500V Ceramicaw200X2300-033IC HA11423
IC501200X2600-183IC STR3B1

SEMICONDUCTORS

0203201K2010-159Diode, 1$2076.27
0204201X2010-159Diode, 1$2076-27TRANSFORMERS & COILS
D208201%2010-189Diode’ 18207627L351201X4710-134Coil, (RF Choke)
0206201X2010-159Diode, 1$2076.27a201%5000.083Coll, Horiz. Size
207201X2010-159Diode, 1$2076-27£701Bi1x0004-007Coll, Adg.
D208301X2010-159Diode, 18207627361202X1300-080Transformer, Hor. Drive
D209201X2010-159Diode, 182076-27ak 1352200x9720-301Meda
301201X2010-165Diode, ISSB1
302201X2010-159Diode, 1$2076-27MISCELLANEOUS
030320%X2010-159Diode, 1S2076-27AF5O1204X7120-073Fuse, 4 Amp. 125V
D304201X2120-009Diode, RH-IV402208X5008-632Recep W Wire 3P-M-BG
0305201X2120-009Diode. RH-IVP201204X9600-466Plug, PWB 3P-J
D306201X2010-159Diode, !S2076-27P202204X9601-477Plug, PWB 6P-Q
AxD501201X3120-216Diode, RM-1AVaot204X9600-298Plug, PWB 4P-B
0502201X3120-216Diode, RM-1AV501204X9600-249Plug, PWB 2P-B
4.0803201X3120-216Diode, RM-1AVPeO1204X9600-304Plug, PWB 4P-C
4.0504201X3120-216Diode, RM-1AVTH6O1201X0100-112Thermistor
0508201X3120-216Diode, RM-1AV
D506201K3120-216Diode, RM-1AV
0701201%2130-234Diode, RU-2VFINAL ASSEMBLY PARTS
0702201X2120-009Diode, RH-1VA 88X0138-50619VLTP22 Pix Tube
201200X3181-523Transistor (NPN) 28C1815GR205X9800-158,Lateral/Purity Assembly
202200X3181-523Transistor (NPN) 28C1815GRAs202X1111-201Yoke Deflection
203200%4058-260Transistor (PNP) 2SA562-Y-TM204X9301-255CRT Socket
204200X4056-260Transistor (PNP) 25A582-291X5004-262Automatic Degaussing Coil Unit
205200%4056-260Transistor (PNP) 25A562-

NECK BOARD RESISTORS CAPACITORS

R401203x6000-728220 Ohm, 5% 1/4W Carbon401202X7050-2691200 pF, 500V Ceramic
Rao2203X6500-540390 Ohm, 5% 1/4W CarbonC402202X7050-248,1000 pF, 500V Ceramic
R403203X6000-661820 Ohm, 5% 1/4W CarbonC403202X7050-248,1000 pF, 500V Ceramic
Raod203X6000-729220 Ohm, 5% 1/4W CarbonC404202X7050-2821500 pF, 1.5KV Ceramic
aos,203X6500-540390 Ohm, 5% 1/4W CarbonC405202X7050-4830.01 uF, '500V Ceramic
aos203X6000-661820 Ohm, 5% 1/4W Carbon
R407203X6000-729470 Ohm, 5% 1/4W Carbon
e408203X6000-998270 Ohm, 5% 1/4W CarbonSEMICONDUCTORS
1409203X6000-661820 Ohm, 5% 1/4W Carbon401
R410203X9104-82418K Ohm, 5% 2W M.O. FormingiosecbTranateioy Nowy as caveet
Ratt203X9104-82415K Ohm, 5% 2W MO. FormingOats200X3206-800Transistor (NPN) 28C2068LB
Rat2203X9104-82415K Ohm, 5% 2W M.O. Forming
Rata203X6000.9982.7K Chm, 5% 1/2W Gomp.
414203X6000.9982.7K Ohm, 5% 1/2W Comp.
R415,203X6000-9982.7K Ohm, 5% 1/2W Comp.1401206: MISCELLAN EOUS Wire4P-E
Rate203X9105-1542.2 Ohm, 5% 2W Metal Oxide40denen eedCaeieweana
Ra19203X6500-7412.7K Ohm, 5% 1/4W CarbonPaoPolecceneeplug, PW 3P-A
R420203X6500-7412.7K Ohm, 5% 1/4W CarbonP403204X9600-961Plug, Bin te
Ra2t203x8500-7412.7K Ohm, 5% 1/4W CarbonProt209na801.020,Plug, PE 4P-E
VR401204X2115.014500 Ohm, -B Semi-Fixed
vRao2204X2115-014500 Ohm, -B Semi-Fixed
R403204X21 15-0085K Ohm, -B Semi-Fixed
vRao4204x2115-0065K Chm. -B Semi-Fixed
R405204X21 18.0085K Ohm, -B Semi-Fixed
Page 76

53 RGB VibEO OUTPUT, or ascisiav f KOT

set ark,

[es01,x302,x800,x808 SYNC AM 1 Jen 2scasac oreacises |

sean ren somePa7|+
Faewy|

von bo

fx | 2scasac on dicicesscebest

X90) POWER DRIVE 2SC2688 ne X92 ERROR AMP — 2501890 ag | = — atthe 81 x08 28cii0¢a, asciasg POWER REGULATOR rr 4. |

nanaemeenfouG8 948 0 wi]ego|
rtae35hceasse
5thynaseace woe¥
aBleGEaeeplfeel
1205 [roc eae curwoe ro TARR-—
Es i oreFjae|

=a] | i

‘| @ eco)

toe[o})jaeSchematic Notes

Unless otherwise specified Resistance: (2) (K--KQ, M-MQ), 1/4 (W) carbon resistor 7 Capacitance: 1 or higher-» (pF), less than 1 (pF)

i1working voltage -» 50 (V)
——HHceramic capacitor
bd|x)L4Inductance: (vH)

2 ep | OYOT crion YOKE Electrolytic Cap: Capacitance Value (»F)/working voltage (V),

aeBra)ifNP - non-polar (or bipolar) electrolytic cap.
one2 Re=|Refer to the parts list for additional component information.
PeesFew|i |p
ee—_—_ 3 ZQindicates test point connection
X701 X-RAY PROTECTORBeSSP BE, ascosrw 3806 or24Y Wovenr wearen4‘.:

2SC454C or 25685 Secaei or B8c2G0eK Se08e9 b indicates chassis ground unless otherwise specified 280820 Hz __ indicates cycles per second AcIZ0V 6oH2/50HE 210% For safety purposes (and continuing reliability) AN replace all components marked with safety syrnbo!l with identical type.

NOTE: FR ~ fusible resistor ——3-'

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 77

REPLACEMENT PARTS LIST - ELECTROHOME 19” MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.: Ceramic Capacitor
Comp. R: Composition ResistorM Cap: Mylar Capacitor
OM R: Oxide Metal Film ResistorE Cap.: Electrolytic Capacitor
VR: Variable ResistorBP E Cap.: Bi-Polar (or Non-Polar)

MF R : Metal Film Resistor Electrolytic Capacitor

CMF R: Coating Metal Film ResistorMM Cap.: Metalized Mylar Capacitor
UNF R: Nonflammable ResistorPP Cap.: Polypropylene Capacitor
FR: Fusible ResistorMPP Cap.: Metalized PP Capacitor

PS Cap : Polystyrol Capacitor Tan. Cap. : Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Part Number

Main P.C.B. Ass'y SU-1133A CRT Socket P.C.B. Ass'y SU-3032A Purity Shield Ass'y 07-220083-03

Page 78

Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19” rN A\Deflection Yoke PC Magnet A AFlyback Transf. aA ASHVR ROS UNF Resistor 2209,25W K C04 C Capacitor 150pF, AC1.5KV X01 Si, Transistor X02 Si. Transistor sc Screw #8-% sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pcs.) C911 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symbol Description

R3105VvR 200
R3106VvR 200
R3113vR 5K
R3114vR 5K
R3115vR 5K
R3116OMR10KQ2W J
R3117OMR10KQ2W J
R3118OMR10KQ2W J

R3119 Comp. R 3.3KQ%W K R3120 Comp. R 3.3KQ%W K C3121 Comp. R 3.3KQ%W K

Capacitors Symbol Description

C3107ECap.10uF 250V A
C3108CCap.1000pF DC1400V P

Coils Symbol Description L3101 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A. QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS53EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 79

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R142 R1422 2FR1401 AR1503 R1504 R1509 R1512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AXR1703 AXR1704 4sR1901 R1902 R1903 R1904 R1905 4Q1908 AR1909 R1910 AFR1901

Capacitors Symbol 1301 1402 C1407 c1411 C1412 C1508 AC1512 Ac1513 ACI514 C1515 1520 C1523 C1524 Ac1531 AC1532 C1904 C1905 Description Si, Transistor Si. Transistor Si. Transistor

Description ASCRT Socket

Main PCB Ass’y (SU-1133A) Parts List

Description v R v R 2002 CMF R 68Q1WJ OM Ro 3.3KQ1WJ OM R 27KQIWI OM R 12KQ2Wd Vv R 10KQ AF R 6822W K ACMF Ro 11.8KQ. YW +1% v R 5skQ OM = R10KQ2W J OM = R B.2KQ2W J OM = R -82022WJ CMF R 8291WJ CMF OR 4.721WJ OM R 6822W J OM = R 39001WJ 2N R ZN R ACMF FR 392%W+1% ACMF R7.68KQ YW +1% AsPosistor UNF R 2Q7WK CMF R 4723WJ OM =R 10KQ2WJ OM R 18K21WJ ACMF RR 472.%W +1% v R 2kQ ACMF R_2.74KQ’W +1% AF R 2202%W K

Description BPE Cap. 3.3uF 50V A Tan. E E E PP A\pP Axpp AXPP PP BPE € M APP AXPP E E Cap. 2.2uF 16V K Cap. 4.7uF 6.3V A Cap. 100uF 160V A Cap. 3.3uF 160V A Cap. S600uF 50V J Cap. 2000pF DC1500V J Cap. 2000pF DC1500V J Cap. 2000pF DC1500V J Cap. 0.53uF DC1200V J Cap. 3.3uF 50V A Cap. 1uF 160V A Cap. 0.1uF 200V K Cap. 2000pF DC1500v J Cap. 1500pF DC1500V J Cap. Cap. 10uF 250V A Part Number 2SC1514VG 28C1514VC 28C1514VG

Part Number A76068

Part Number QVZ3230-002 QVZ3230-005. QRX019J-6R8 QRG019J-532 QRG019J- 272 QRGO26J-123Z QVZ3230-014 QRHO24K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRGO026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO019J-391 ERZ-C05ZK471 ERZ-COSDK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRG026J-103Z QRG019J-183 QRV122F-470Z QVP5A0B-023E QRV142F-274] QRH124K-221M

Part Number QEN61HA-335Z, QEE51CK-225B QEWS51JA-475 QEW52CA-107 QEWS2CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106

Page 80

Coils Symbol L1502 L1503 L1504

Transformers Symbol 71501 71503,

Semiconductors Symbol 1C1501

X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 X1902

D1101 D1102 D1103 D1301 D1401 D1402

D1503 D1504 D1505 D1506 D1507 D1508 Ab1701 A\D1901 A\D1902 A\D1903 A\D1904 A\D1905

Miscellaneous Symbol AF1901 A\F1902 Description Linarity Coil Width Coil Heater Choke

Description Hor. Drive Transf. Side Pin Transf.

Description IC

Si. Si. Si, Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si.

Si. Si. Si. Si. Si. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor

Diode Diode Diode Diode Diode Zener Diode

Si. Si. Diode Diode Zener Diode Si, Si. Si. Diode Diode Diode A\Zener Diode ASi. ASi. ASI. ASi. Diode Diode Diode Diode A\Zener Diode

Description AFuse 1.254 ANUL Fuse 34 Part Number A39835, C30380-A C30445-A

Part Number A46022-BM C39050-A

Part Number HA11244

2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 280478 280478 2SC2610BK 2SC2688 (K.L.M.) 2SC1890A (E.F.) wosA Wo6A wosA 182473H 18Z473H RD10F(C) HFA VO9E AD11E(B) WO6A 18S81 1$Z473H RD20EV2 1S1887A 181887A 181887A 1S1887A RD6.8EV3

Part Number QMF53U1-1R25S QMF66U1-3R0S

“17

Page 81

X11, X103 ond XIO5 VIDEO AMR, 2504346 yy 25¢1685 XiO2.x104 ond XI08 VIDEO AMP 25A673C QReedTRER SECT, ee aE PRT dF E ne poten seaiew

{Lf x303 seam umiter 2sa673 ay [7304 BLANKING | 28casac

x304

\eor PoweR REGULATOR STRse8 SU-I103A MAIN PCB ASSY

x401, xa02 saa

Schematic Notes Unless otherwise specified Resistance: (Q.) (K->KQ., M->MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1» (yF) working voitage -> 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value (v F)/working voltage (V),

  • XY PROTECTOR SONOME conn Bee NP — non-polar (or bipolar) electrolytic cap. 28Ca6il or Zcz6i0BK 250869 Sieh oe Refer to the parts list for additional component information. ACIROv SOHs/S0H : Q indicates test point connection oy indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) rN replace all components marked with safety symbol with identical type.
NOTE: FR— fusible resistor «

G07-FBO Parts identification on circuit boards: 00-4147-03 e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 82

REPLACEMENT PARTS LIST - ELECTROHOME 13”’ MONITOR

OT

Components identified by the A symboi in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.

{ a

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.: Ceramic Capacitor
Comp. R: Composition ResistorM Cap: Mylar Capacitor
OMR: Oxide Metal Film ResistorE Cap.: Electrolytic Capacitor
VR: Variable ResistorBP E Cap.: Bi-Polar (or Non-Poiar)

MFR : Metal Film Resistor Electrolytic Capacitor

CMF R: Coating Metal Film ResistorMM Cap.: Metalized Mylar Capacitor
UNF R: Nonflammable ResistorPP Cap.: Polypropylene Capacitor
FR: Fusible ResistorMPP Cap.: Metalized PP Capacitor

PS Cap : Polystyrol Capacitor Tan. Cap. : Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order. Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.
SymboiDescriptionPart Number

Main P.C.B. Ass'y SU-1103A CRT Socket P.C.B. Ass'y SU-3016A

Outside of the P.C.B. Ass'y

SymbolDescriptionPart Number
AvotAsPicture Tube370ESB22(E)
AsDY01.A\Deflection Yoke29123-V

FO Magnet A76366-A Wedge 30006 AsFlyback Transf. A19183-A

ARI1AFocus VRA46606-A
AROSUNF Resistor 2202, 25W. KQRF258K-221
4xco4ASC Capacitor 150 pF, AC1.5KVQCZ0101-005
X01Si. Transistor2SD869
1CO1iC RegulatorSTR383
Lo1Degausing Coil21-1007-31

Degausing Coil Pin Terminal (2) 34-708-01 Degausing Coil Pin Terminal Housing 34-709-01 Groundstrap Ass'y. 34-697-04 Groundstrap Wire Terminal 34-228-03. Groundstrap Spring (2) 35-3560-01

BRSupport Bracket RH35-3919-01
BRSupport Bracket LH35-3919-02
scSCREW 10-% Pix Tube Mtg. (4)31-631018-08
WAPyramidal Lockwasher (4)33-255-01

Clip P.C.B, Support (2) ~ 33-629-02 Ground Lug 34-33-04

CHChassis Base38-452-01

8-19

Page 83

Mair: P.C.B. Ags'y (SU-1103A) Parts List

Resistors Syrabot 1408 1408 RI410 R414 R1415 R1421 R1422 ASFR1401 A\R1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 ASR1703 ASR1704 ASR1901 R1902 R1903 R1904 ASFR1901

Capacitors Symbol 1402 C1411 C1412 1508 C1811 AC1512 AC1513 AC1514 C1515 C1526 C1524 C1904 C1905 A\C1907

Cols Symbol 1501 L1502 1503 1504 L1901

Transformers Symbol T1501 T1503 Description v v Rg R CMF R OM OM OM v AF mnpoxuD A\CMF R Vv OM OM OM R R R R CMF R CMF R OM OM ZN ZN R R R R ASCMF R ASCMF R APosistor UNF R CMF R OM AF R R 20a 2009. 6.8Q1W J 3.3KQ 1W J 2.7KQ1W J 12KQ2W J 10KQ 6822W K T1.BKQYW +1% 5KQ 10KQ2W J 5.6KQ2W J 6802.2W J B.201W J 4.7Q1W J 56Q2W J 390Q1W J

39K QW +1% 7.68K QUW +1%

207W K 5.623W J 10KQ2W J 2202%W K

Description Tan. E E PP E APP AXpP A\pP PP

M E E A\MM Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. BPE Cap. Cap. 2.2uF 16V K 100uF 160V A 3.3uF 160V A 5600pF SOV J 47uF 160V A 2000pF DC1500V J 2000pF DC1500V J 2500pF DC1500V J 0.53uF DC1200V K 1uF 50V A . O.1UF 200V K Cap. Cap. Cap. 10uF 250V A O.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transt. Side Pin Transf.

8-20 Part Number GVZ3230-022 QVZ3230-022 QRX019J-6R8 QRGO019J-332 QRGO019J-272 QRG020J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG028J-562 QRG029J-681 QRX019J-8R2 QRX019J-4R7 ORG029J-560 ORGO019J-391 ERZ-C052K471 ERZ-C05DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5RE QRG026J-103Z QRH124K-221M

Part Number QEES1CK-225B QEW52CA-107 QEW52CA-335 QFP31HJ-562 QEW52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS2EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A A39475-J

Part Number A46022-BM C39050-A

Page 84

Semiconductors Symbo! 101501

x1101 x1102 x1103 x1104 x1105 X1106 X1301 x1302 X1303 X1304 X1305 x1401 x1402 x1501 x1701 01101 D1102 01103 01301 D1401 D1402 D1503 01504 01505 01506 D1507 D1508 4801701 A\D1901 AxD1902 A\D1903 A\D1904

Miscellaneous Symbol ASF1901 AF1902 Description LC.

Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor iode jode |. Diode i. Diode i. Diode Zener Diode Si. Si. . Diode . Diode Zener Diode Si Si. Si |. Diode |. Diode . Diode AdZener Diode ASi ASi ASi ASi. . Diode . Diode . Diode . Diode

Description A\Fuse 1A ANUL Fuse 3A

8-21 Part Number HA11244

28C1685(R) 2SA673(C} 28C1685(R) 2SA673(C) 28C1685(R) 2SA673(C) 28C1685(R) 2SC1685(R) 2SA673(C) 28C1685(R) 28C1685(R) 2sD478 2SD478 28C2610BK 2801685(P-S) Wo6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 Voge RD11E(B) Wo6A 1$S81 182473H RD20EV2 181887A 181887A 181887 181887

Part Number QMF53U1-1ROS QMF66U1-3R0S

Page 85

CRT Socket P.C.B. Ass'y (SU-3016A) Parts List

Resistors Symbol R3105 R3106 R3113, R3114 R3115 R3116 R3117 R3118 R3119 R3120 R3121

Capacitors Symbol C3107 C3108

Coils Symbol 13101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description 2002 2002 5KQ 5KQ 5KQ IM 10K Q2W J IM. 10K 22W J OM R 10KQ2W J Comp. R 3.3KQ2%W K Comp. R 33KQ%WK Comp. R 3.3K2%WK oo<<<<< DDUDUDDD

Description € Cap. 10uF 250V A C Cap. 1000pF DC1400V P

Description Peaking coil

Description Si. Transistor Si. Transistor Si. Transistor

Description XCRT Socket

8-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRGO29J-103 QRGO029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS52EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2802611 28C2611 28C2611

Part Number AT5522

Page 86

IX Schematics and Wiring Diagrams |

Page 87

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 88

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 89

MT-9I XFORMER VIDEO BD,

  • sc04- 91431~ C300

MIDWAY MFG CO, 1601 W. BELMONT AVE. FRANKLIN, PARK. iLL. 60131 16 GA. 500¥. NSUL.WiRE 3 G-¥ GND. GOES TO ON-OFF sw, WONITOR , otN-D00R conraou ‘ wosi=o0ne2- A008 rq i 1

tot_a
POWER SUPPLY BD,|a7
1082. 30421~ C000L11\1
roiwT)cs l DScloTS]
!It 1
wltevom
heaeli |
olssMPU / SOUND BD.
Co$mED itba on# 2084- 31430- C300
Voyitevom xlog | ros
Vateovwtet
VogtaI.!
1 Lglow,y-vo x<0.lL!
VoutoN,=2I aPeal
i} u weyRei!
7=Ts 3u2 2 posoe_8 a3 7re8.
Spais Sa eS 8-=+= 5-=
iolty oY Vy eV ffyh| aw 443bo yyy yy yy
ioa] PTPrey~
totVqee4adddyd Fo 4Jiddgdgadadee
Puy, Trot| 4 a] aa ol J al Qgagdagiaa3 2 4 3
Vol ou seruanvowye

it urd 2 | +

—_T| |10.yeux0. v-vowdiag es4honeJa
MT-95 X-] FORMERBitesi RETRyenSg ElSJ SiS gy 8pels)Slot ef"
Ewssotwoeeris is bbL RALUAAAA A
S27 MONITOR* con 9aN <Wcom METERsosene
EE)nhsmAtm=

ou mre slay

E2 ANP stO-Btb|herex
[Oeome 5 ooeaonlat «

uae CON DOOR CREDIT BYPASS BD.

  • a

as ener

aevaxsw nevuan
10) 7518. a0|wa x-b5y UNREG.

a

sarety 9m, ria nue pu Pere n Fal

Sore Se-_rele~BLUE PRINT CT.NOTES 1, x= wos, warevion__OATE_ ue

2F aN ay FISHED 7-73-82

Page 90

DESIGNATION LIST

DESIGNATION DESCRIPTION 100 (Omt RO TANT c101 0.4 7mt RO TANT 35V C102 470m! AX ELEC

c1os 25,000mt AX ELEC clos. 4.7 ROTANT 35 108, cio7 Osimt

cm O.ime cus 40,000m" AX ELEC cua 470 mt Bx ELEC cus 220m Ax ELEC 25 cus 4700mt AK EEC 28/ cur a7t cue O.tmt

cuz ouimt

R100 100 OHM 74 W 5% CRE R01 410 Riz 0.18 OHM Sw 5% RI03 0.16 OHM Sw 5% Rio4 6B OHM I/2W5% CRB fit 24 OMM fA W5% CRB RI06 270°

an 1.2 OHMUAW5% CRE Rite 560"

Riza 25 08M Sw 10% R128 68 OWM I/2W 5% CRE

19 OMM VeW 5% CRE ati ty 6.2K iK

150 ORM 2W 10% 68 OHM 1/2W 5%.

100 OHM POT

4001

MR 750 'naoo AISF Sov 58

P2908

M308

ERRITE BEAD FERRITE SEADNTG HORW 2-206 $0.10 WiRE

9-4 sal asa

fF Fe Fue?

Jive a v2

W123

Twi tw2 Tw3,Twa

Ler cee ves DESIGNATION

RIZE R127 R28 R129

A132

risa

R100, vR101,vR102

Bios 0106, 0107 2108, D108 Dito, Ou,0112,013,, 014,015,016

2102, c104

ve

us

Fe1,re2 FEM, FaMH2

MEATSINK ASSY, WEATSINE ASSY. MTG HLRW 24-40 X10 SLTRNO 4 WASHER,4, 120-250 018 274-40 HEX NUT THERMAL COMPOUNO

FUSE,I/44, SLO-8LO FUSE. IAMP. 1P W/STOF

2°08 KK-IS6 pos" 13F0s" Pos *

JUNPER WIRE

THE wRae TIE WRAP

TAG, FUSE 1/6 A SL0-BLO TAG, FUSE AMP TAG, PWR. SPLY.LO “(ene TD [oe

err

one

mise

Pim twa

ons.

oe 1) SEFREE Ta °

nansa 24,28, bewe ere estiee ee amie

HE NOTE: RS-RESISTOR SPACER

provect ENG: J. JARON CROSS REFERENCE LIST

DESCRIPTION

a7 ot

0.47 ut RO TANT 35 4.7 yt RO TANT 35V

  • ut RD TANT 470 pt AX. ELEC. 2200p AX.ELEC.25y 4700ut AX ELEC. 28 25000 uf AX.ELEC. 40000 ut AX. ELEC.

16 OHM IS.W 5% 18 SW 5% fo" vaws% CRB 24 i 25 "sw 10% 68" 2w5% 100 aw 8% CRE 150 2 10% 270" vaws% 470 OHM I/4W 5% Sor a are " lek” 6.2 K OHMIZ4W 5%"

100 OHM POT

A\SF 50 SA DIODE

iw 4001

MR 750

2nz905

Lm sos,

FERRITE BEAD FERRITE MTG HARDWARE

206 SoLio wiRE

HEAT SINK Assy HEAT SINK MTG HARDWARE

4-40 £10 SLT AND WSH.4, 1205250°018 4-40 HEX NUT

FUSE, v4A SLO-8L0 FUSE, SAMP FUSE CLiP w/sToP

2 POS. KK-I56 CONN 5 Pos. ePpos 13 Pos

22 AWG. 2.2 IN

TIE WRAP 7 5/8 IN TIE WRAP 10 ¥/41N

TAG, FUSE /4A.SL0-8L0 TAG. FUSE 1AwP TAG, PWR SPLY 1.0,

70 vA PWR. SPLY PC

HEAT SINK ASS'Y DESIG.NOS. PART NOS,

cn? 0948-00811-0100

£106, C107,c111, 0945-00811 -9200 cus. cat

cir 0945- 00816-1100 C108 0945-00811 -0400 6100 0945-00816 -1000 cio2,ci4 0945-00818-0600 cus 0945-00816 -1300 cue 0945-00811 -0700 cios 0945-00816-1700 cg 0945 -00818-1800

R103 0945-00815- 0100" R102 0345-00815 - 0200 Rize 0062-05183 -1xxx RI08. 0062-06585 -1xxx Ri24 (0945-00815 -1000 R104,RI25,8134 0082 -098D3-1XXX Ri00 (0062-11083 -1xxx Ri32 (9945 -00812-0200 RiO6. 0062 -13685~1xxx Rio 0062 - 15683-1xxx Rua (0062-16283 -IXxx RI27,R129 0062 -17983-1xxx Rus. 0062 18383 -1Kxx Rize 0082-217 83 -1xxx

VRI90, VRIOI, 0945-00814. 0000 vR 102 b110,01N1,9112, 0113, 0114, 0115, ONG 0103, 0108,0108

p106, 0107

102, 0104

v2,u5

Fel.re2 FOMHi,FOMH2

OM, FBMH2

Wsat Hs

HSAL HSAI HSAI

fe F2 Fie2

vt shee ve ut

wi, 02, JW

Tw3, Tw4 Twi, Tw2

ver cee ces 0949 -00804-0200

0945-00804-0300

0945-00804.0800

0945-00808-0300

0945-00813-0100

0017-00009-0225

0017- 00033-0139

4945-00008-0100

0017-00101 - 0127 9017-00108- 0071 0017- 00103-0002

0017-00003 -0446 0017-00003-0601 00!7- 00071-0033

3000-16387-0200 3000- 16387-0500 3000 - 16387-0600 3000- 16387-1300,

0151 - 00087-0000

0945-00814 -0300, 0945-00814-0400

Mo5!-00945.4020 M051-00945-a021 Mos! 00945-4022

8080-9042 1-C000

0017-00033-0139

REVISIONS Juseo on BLUE PRINT

ASSY DRWNG. MED RS. 70 VA (A082 -90421- C000) A082 -90427-A000 PART no. @ty | MIDWAY MFG.CO.

MO5I- 00945

Page 91

——2{ umzos |

| ome 120 sense —

on

anne s ougaew x : [Le a) Save | ava —- a a |

  • M305. |!

L SUPPLY TOVA 00945-4032 A

Page 92

CROSS REFERENCE LIST DESIGNATION LIST

DESCRIPTIONaryDESIGNATIONPART NOS.
330pf SOVCROSC1c20300-00800-1402
DESIGNATION.DESCRIPTIONDESIGNATIONDESCRIPTIONSW ARoeR_cpl pice'0300-00800-0700
Jooout AX ELEC\cl0300-00800-1200
cPi-crioeslut AX CERle74.832
ct1000ur28VAKELEC2e74Lsi0
ce3309f50V CR DSCae74L8 86

NOE Ite 74Ls32 ite 74.8157

SE74 LsI86={0062- OB3-IXxx
RI-R4100 obM vaw4RI-RS3
n5-R3ero on 7a14e7avsz6s210 onmizaw‘as-recose i3052-¥0%
RS, RIC\KOKM 741sSse dhe330 OHMI/4W2RUIZ(0082-144B3-1XxX
RU, RIZise74LSi571k O4M I/4W8R3,RIO,RIZ-RIS0062-I79B3-IXxX
IRIE330 OKMI/6WDEqausean

13-RI

. idTete18-206T4LS166

2IE 74US157

ea 7aLs08 1A

2Tatsoeail2ec-r,6,12680,0300.00803-0081
3A-6874Lsi61'20,150,'80
77aLs7a2e74Ls007418006194, 13C, 15-170,(0300-00803-0027
8K74Lsi07ae7aLsoe2F
3A,10874Ls04ueRAL acey4Ls0212a(0300-00803-0028,
120,134,74.8161\2Fwousey.7aLs0439A,108, IF(9300-00803-0029
LAA, ISA74Ls86\3FTa Lene)74LS0882A,06,98,15E,4F©300-00803-0030
'6A-18a748201aMito74Ls1032B,14C,2E0300-00803-0051
19474Ls0015Etausets:74L$20117F0300- 09803-0052
20874187ler74Lsi7474.827212F,20F0300-00803-0083
2474LSI75VeiauseeT4L832714,118,198, 8C,1E,0300-00803-003!
18F- 20F74 LSi68DEE
air7482774TAM9300- 00803-0032
L87421B
ie7aee oe:7488610148,154, 38-68,1480300- 00803-0054
12otsISB, 4E,13F
eB74LS10"eA,)=(- 0055
74Ls10728A, 210300-00803- 00:
paidwat eee74LS139120c0300-00803 0034
rd74Ls28374Lsi5s74"20A,8C-10C, 00,100,0300-00803- 0050
101Ab a110,140, I2€,16E, 21€

|A-GA,I28,13A,128, 0300-00803-0044

129,1387418161vatsiel83AA, I80
Ere.74LS06IcsieAa-I8A18-PINIC SOCKET74LSI66101C,2C,10,20,18E-20€, —_ 0300-00803-0048
ie" 128748201168-188o1eF—20F
sosarssea:T4LSI74116F0300-00803-0047
208T4USi75" 6C,7C“74Lsi75221,208(6300-00803-0035,
a7ALSi98B leatac‘745201616A- 18A, 168-1880300-00803-0056
“3D741824546D,70,120,77E0300-00803-0046
74LS32ie74.82736108, 18C,19C, 130,0300-00803-0038
74LsI60© een210,15F
214B09_R-G-B EPROM KIT3170, 180,200£300-90000-R300
TAL SIS7BKG EPROM KIT23C,30A300 -90000-R400

au

74.800XTAL1OMH2 CRYSTAL16 PIN 1 SOCKET616A-18A,0508- 00804-0700

74Lsio 168-188 Wc-17e 74.800 18¢, 19¢ 7a S273 20¢ 748139

2cT4LSIIBBI,BB2BUSS BAR18 PIN IC SOCKET86C,7C,11C, 126,0300-00804-0900

$107 80,90, 180,180 ed 74.8157

1.2074.sI66Pl50-PIN CONN, MALE

30 EPROM

60.70Tau seas248IN IC SOCKET530, 30,170,180,©300-0080-1000
80,90augP220-PIN CONN, MALE200

100,110 74.187 20 TaLseas 30 PaLS273, 140 74L8i87

peealteJOMHZ CRYSTAL1XTAL0300- 00804-1100

80,200 EPROM zip 7418273

Bus BAR2881, 8620089 - 239xX-XBNX
20PIN CONN.,MALEP20300- 00804-1103

REvONS — ProuecT FMG:_J, SZERSTEN [seo on BLUEPRINT (aly | MIDWAY MFG.CO. Do NOT acAuh OFS. FTNONE [wore 1(ONE) PmANRLI PK TLL

Ta TSEa~=104
9-6meASSEMBLY DRWG. BLUEPRINT |rar 050 PIN CONN. MALE1Pl0300-00804

VIDEO PC. BOARD AQB4~ 91431-0300 M051 ~- 00300 ~-D007

VIDEO PC. ROSA'——
Page 93

8-7 X NOTE: ON"A” VERSIONS

PING! TO +Sv.

ALL EPROMS, 2532, WITH PIN-18

TO ADDRESS LINES (AS PIN-21 ON 77328)

Page 94
DESIGNATION LIST—L/*CROSS REFERENCE LIST
DESIGNATIONDESCRIPTIONDESIGNATIONDESCRIPTIDESCRIPTION QTY DESIGNATION. PARTDESCRIPTIONQTY DESIGNATION -PART.NO.
f8:c80Owe"aertsoeeo.Ag eSvasromr"2‘2308-00800 1700
es1-ceeME mo. raneLeTes oeB 4& |||01 urv808:2600CHOKE 10 uM MoLoED+ute0300-00804-1107
eeraie aaaeLerSNE as=O00:1208.(CHOKE 10H W/W3teetir(9300-00804-1108
cre. OME.badideal71S MF AX. TANT. !¢700300-00800-14013U,3V
crs1M RO TANT.59yelncs=NOOOMF Ax.ELEC. 3674-076'0300- 00800- 1200aorin >PyHESL.3N, IP0300-00808- “109
Aeest‘22 0KMUGWSRCRENR380062-06383 ~1xxxTPIN CONN KK-I56.1v33000- 16367-0716
cPi-crs21 MF AK CER.albeatles56rsBIR,OPIN“1vt3000-16367- 1011
artgre “EeeUS-LITCHOKE [OU W/Wine * 59 fw RIT- R33, R36,50 PIN‘Pry0800-00804- 104
aiss= areeee.-_5K Por2VRILVR210300-00804. 0600
nasenenezpauleant4—70 nz CRYSTAL‘xtact0300-00804. 108
naraes gd REnoise1or0300--00801- 0001
orrae10 PIN CONN KK-I581140081be300- 00801. 0002THE waaes2rwi.twe9017-00042-0048
oeEnerversSUA ig Pe go Srace3=FitopeauACKGROUND VOL.CONTR.LAL 1oxe1051-00300- note
benesesmi, swa2 Fos.o1P sm.+iaIRTa Uso)ANee
HePe swirenfTfasostte 36‘0300-00803-0043MASTER voL.coura,‘Tanm0s1-00200-4018
azaps(8, By lay lepatsise;to 0
PIN RIBBON CABLE"Heeeeee=Ug
te 28raisszom memmoN coei:a:5 bern2yatsa7a'te on0300- 00803-0088

Bs.ar = 1

eeaad“rue [roe one PER:
=f7ASSEMBLY OW.pane se
:=a.ueprin meursouno | Mosi- 00300 -€00s
Page 95

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 96

-DESIGNATION LIST

DESIGNATION DESCRIPTION cl 10 mf I6V RD. TANT c2 O.Imf 50V CR. DSC. c3 -OOlmf [OOV ESTERF c4,Cc5 Imt 35V RD. TANT cé6 -Olmf 500V CR.DSC. C7 4.7 mf 35V RD. TANT

CPI-CP4 «lmf 50V CR. DSC.

RI,R2 4.7K OHM 1/4W R3-R6 1K OHM 1/4W R? 150 OHM \/4w R8, RO 68 OHM I/4W RIO 270 OHM I/4W RU 18K OHM W4w R12 4.7K OHM \/4W

DI-D3 IN5817 SCHOTTKY D4,05 IN4148 DIODE

ul 7414 v2 7474 u3 74LS193 u4 555 TIMER

Jl CONNECTOR ASSY.

swt 4 POs DIP Sw.

MHI-MH4 SNAP BUSHINGS, I/78"

9-10 —CROSS REFERENCE LIST.

DESCRIPTION

  • OOI mf |OOV ESTER F . Ol mf 500V CR. DSC «ImfSOV CR. DSC Imf 35V RD. TANT
  • 7mf 35VRO. TANT lOmf 16V RD. TANT Coan anon [| 68 OHM I/4W 150 OHM 174W [us (oe Ul 270 0HM I4W 1K OHM 1/4W 4.7 K OHM I/4W CRS 18K OHMI/4W cs@ | oy 8 c4a@ sepa] Coco IN4148 DIODE CRO IN5817 SCHOTTKY

MH MH4 4 Oc (45N] Gen) + J 655 TIMER 7414 7474 74LS193

CONNECTOR ASSY.

4POS. DIP Sw.

SNAP BUSHINGS,|/8"

CREDIT MULTIPLIER P.C, BOARD

prouvecT ENG: J. SZERSZEN DO NOTSCALE DW. a a ome 8/282 a DIM. TOLERANCES UNLESS SPECIFIED

CONCENTRICITY T1003] FRACTIONAL ‘aed DECIMAL 005 HOLE DIA... $.002 000) QTY. —--NOU-—

“ -Wwah--wn

wale NONE NO.REQ'D 4 (()NE)

ASSEMBLY DRAWING, CREDIT MULTIPLIER P. C. A082 91348 C000 DESIGNATION

c3 cé6 C2,CPI-CP4 C4,C5 c7 cl

R8,R9 RT? RIO R3-R6 RI,R2,R12 RU

04,05 Di-D3

U4 Ui v2 U3

Jl

swi

MHi-MH4

Baby | MIDWAY MFG. CO.

PART NO.

MO51~-00932 -C027 PART NOS. 0932-00820-0303 0932-00821 -0401 0932-00820-0302 0932 -00820-0304 0932-00820 -0305 @932-00820-0306

0062 -O098B3-1 XXX 0062 -122B3-1XXX 0062-138 B5- 1XxXxX 0062-179B3-1XXX 0062-21183 -IXXX 0062-2 39B3-IXXX

0932-00821 -0402 0932-00809-0000

0932-00819-1801 0932-00819 - 1803 0932-00819 - 1804 0932-00819 -1802

0932- 00817-0400

0932 - 00821-0401

0017 - 00042-0014

A080-91348- COOO

Page 97

eH AOS 4W I" {F

ASE 4W Ol

FROM GAME 80 RESET)

a Ou Gu by ey

“XW YR. he vt cs t .OOIMF50) =r MYLAR en |

GND. | U3 a T4LS193

TO GAME 80 COIN INPt

Zia

SCHOTIKY DIODE

2X INS58I8 4Ld

OR INS8I7

ae D2 va y 8I

D3

[T's MS _NIOD oH AWOo! ad |LINw

DO NOT SCALE DWG. tt BblbNI XZ ANVL Ase JW tL

REVISIONS

MIDWAY MFG. CO FRANKLIN PK

USED ON PAC-MAN HLL

NO.REQ’D ONE PER

DIM. TOLERANCES UNLESS SPECIFIED vate OB/I7 /82

CONcENTRICITY T1R 003) FRACTIONAL, +1764] DECIMAL + 005] HOLE DIA. ¢ 002 000)

9-11 FINISH PART NO.

SCHEMATIC DIAGRAM CREDIT MULTIPLIER A082 - 91348- C000 MOS!I- 00932- C029

TION LIST

DESIGNATION Jl PCHMLPCMH2 \ PROJ.ENG=J,SZERSZEN DIM. TOLERANCES Sr PAC-MAN DESCRIPTION 7 PIN CONN. KK-156 W/PIN 3 REMOVED C) 8’ HEYCO NUT DSCRP. 7 PINCONN. KKIS6 W/ PIN3 REMOVED QTY DESIG.

i PART NOS. J) 0932-0081 7-0400)

00 e000 /8"HEYCO 2 NUT PCMHI, OO17-00042-0014 PCMH] Pc BD ! — A080-91109-A000

PCMHI THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO.

USED ON UNLESS OTHERWISE SPEC. DATE CONCENTRICITY T.LR. . 002 | °° BB [ ‘08/iabe MIDWAY MFG. CO. FRANKLIN PK., IL. 60131 A BALLY CO.

DECIMAL. . £005 FRACTIONAL ...... 2.1164 brea rat +.002~.000

ASSEMBLY DWG PART NO

+1/2° FINISH CREDIT MULT. BYPASS PC BDIy.9-5-1 -0-0-9:3-2 - A:Q-2:7

A082-91109-A000

Page 98

PROJ.ENG.: J. SZERSZEN THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO. UNLESS OTHERWISE EPEC: 7 SCALE MID WA Y MFG. co. 8/2782 [ NONE GONCENTRICITY T.LR. . 902 by FRACTIONAL ...... + .1/64 vitesse 66277 308 acre See yt oe MULTI. [parTNoare YPASS P. C. = 112° 5-1 -0°0°9'3'2 -A-0'2°8 DO NOT SCALE DWG. A082-91109-A000 vee 9°0°9°3°2 FRANKLIN PK,, IL. 60131 ABALLY CO. REVISIONS