CATHODE RAY TOMES

Area 51 TM-402 2nd Printing

Area 51 (R3000) (Atari Games, 1996) · Technical Manual · 56 pages · 74 sections · original scan

Page 1

‘TM-402 2nd printing

Operators

Meir) Ue]

_TIME WARNER INTERACTIVE |

Page 2

oe _gniday . ac vine) cond P ci

Page 3

Operator’s Manual

with Schematics

Sia

TIME WARNER INTERACTIVE _

Page 4

INTRODUCTION AREA 51 OPERATOR'S MANUAL

NOTICE

COPYRIGHT

Copyright © 1995, 1996 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976

This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in Infringers may also have to pay costs fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations,

Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game,

Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95035 Printed in the U.S.A. 1/96 Produced by the Time Warner Interactive Technical Publications Department. Design: Andrea Dencker Writing and Editing: Ray Munson Cover: Andrea Dencker and Steve Caterson

NOTICE RE

NON-ATARI® PARTS

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following © Substitute non-Atari parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation

FCC COMPLIANCE

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.

  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMD ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

AREA 51 Operator's MANUAL “ INTRODUCTION

SAFETY

SUMMARY

‘The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply:

WARNING

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tubes (CRTs). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRTs before servicing them. Do this after you disconnect them from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRTs With Care. If you drop a CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Handle Disk Drive Unit With Care. Use special care when installing the circuit boards and handling the hard disk drive. Take basic precautions to avoid excessive impact or electrostatic discharges. Attached to the hard disk drive is a shock indicator that detects severe impacts. Do not remove or tamper with this indicator. Thoroughly review the operator's manual and videotape provided with this product. Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS

In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be

a damaged or destroyed if instructions are not

followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.

WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

Précautions de’Emploi Générales \™

iii

Page 6

INTRODUCTION & AREA 51 OPERATOR'S MANUAL

PRECAUTIONS

DE’EMPLOI

GENERALES

Les précautions d'emploi ci-dessous s'‘adressent & toutes les personnes susceptibles d'utiliser ou de réparer ce jeu. La presente notice renferme également d'autres mises en garde et avertissements spécifiques.

MISES EN GARDE Mettez le jeu 4 la terre. Les joueurs risquent de recevoir une décharge électrique si le jeu n'est pas correctement mis a la terre! Pour éviter les décharges électriques, assurez-vous que le jeu est correctement mis a la terre avant de le brancher. Branchez-le uniquement dans une prise tripolaire avec mise 4 la terre. Si vous n’avez pas de prise tripolaire, il est recommandé de faire appel a un électricien breveté pour en installer une. Si la console de commande n'est pas correctement mise 4 la terre, les joueurs risquent de recevoir une décharge électrique! Si une réparation quelconque a été faite sur la console de commande, urez-vous que le fil de mise a la terre est solidement attaché 4 l'intérieur de la console. Ceci fait, verrouillez le jeu.

Branchement sur secteur. Avant de brancher le jeu, assurez-vous que son bloc d'alimentation est compatible avec la tension secteur locale. Les conditions d’alimentation du jeu apparaissent au premier chapitre de la présente notice. Débranchez le jeu du secteur avant toute réparation. Pour éviter les décharges électriques, débranchez le jeu du secteur avant de le démonter ou de le réparer. Utilisez uniquement des piéces TWi. Pour éviter les risques d'accidents, utilisez toujours des piéces TWi pour réparer le jeu. L'emploi de piéces d'autres marques ou la modification des circuits du jeu sont potentiellement dangereux pour le réparateur et pour les joueurs, Utilisez les fusibles appropriés. Pour éviter les décharges électriques, remplacez les fusibles par ceux indiqués dans Ia nomenclature du jeu. Les fusibles de rechange doivent étre du méme type, de la méme tension et de la méme intensité que ceux d'origine.

iv ATTENTION Attachez correctement tous les connecteurs. Assurezvous que tous les connecteurs sont bien enfichés dans les cartes circuits. Ces connecteurs sont dotés d'un détrompeur qui €vite les erreurs de branchement. S‘ils s’enfichent difficilement, ne forcez pas. Si vous branchez un connecteur a l'envers, vous risquez d’endommager le jeu et d’en annuler la garantie. Vérifiez la fréquence de ligne du courant secteur. Les jeux fabriqués pour fonctionner 4 une fréquence de ligne de 60 Hz (fréquence utilisée en Amérique du Nord) ne doivent pas étre utilisés dans les pays dont le courant a une fréquence de 50 Hz (Europe). Si vous branchez un appareil congu pour une fréquence de 60 Hz sur un courant d'une fréquence de 50 Hz, le transformateur ballast de l’éclairage fluorescent surchauffera, ce qui présente des risques d'incendie. Vérifiez la fréquence de ligne requise par votre machine; elle est indiquée sur sa plaque signalétique.

REMARQUES, AVERTISSEMENTS

ET MISES EN GARDE Dans les publications d’TWi, les conventions, en ce qui concerne les remarques, avertissements et mises en garde, sont les suivantes: REMARQUE — Sert 4 attirer l'attention sur un point particulier,

AVERTISSEMENT — Le non-respect des directives présente des risques d'endommagement et/ou de destruction pour le matériel et/ou les piéces. En cas d’endommagement ou de destruction du matériel ou des piéces, résultant du non-respect des directives, la garantie offerte sur les cartes circuits TWi et les piéces connexes TWi sera annulée.

MISE EN GARDE — Le non-respect des directives présente des risques de blessures ou d’accidents mortels pour les joueurs et/ou les réparateurs.

Page 7

CONTENTS

1 Set-Up How to Use This Manual Operating the Game . Inspecting the Game Control and Switch Locations 12 Power On/Off Switch. 1-2 Volume Control... 2.00... 0 eee .. 12 Self-Test Switch ..... . nee seceeces 12 Coin Counter... 2.6... 26. save 1-2 Video Display Controls ............0.... 13 Setting the Coin and Game Options ........... 1-3 Game Overview... 02.0.0 0. 000. cee eee 1-3

2 ~~ «Self-Test Introduction. fev e eens » 2-1 Entering and Exiting the Self-Test . 2-2 Using the Gun... . 22 Select Test Menu... 6.0.0... 0000. 2-2 Adjust Volume... 6.00.00 eee 2-2 Statistics. OES eure OAL e MERRAE are 23 Statistics Screen... 22.2.2... seven eee 23 Histogram Screens .. 2.2... 0. ee ee 23 Game Options Coin Options Controls Test . . Gun Calibration . . . Disk Test. Memory Tests .... Monitor Tests. . . Color Test . Purity Test. . Convergence Test .

  • =Troubleshooting and Maintenance

Introduction. ... . Maintenance Procedures. . Introduction Bagi ss teuee : Cleaning Procedure for Coin Mechanisms Troubleshooting Procedure: Repair Procedures . Introduction Speaker.......0....0.. Attraction Panel Light Bulb .

System Logic Assemblies Video Display .

4 Parts Illustrations

For figure and page numbers, see the list of illustrations that follows.

5 Schematics

See the list of illustrations that follows.

Warranty Inside back cover AREA 51 OPERATOR'S MANUAL INTRODUCTION

v

Page 8

INTRODUCTION # AREA 51 OPERATOR'S MANUAL

Figure 5-1 Area 51 Game Wiring Diagram.. I LLUSTRATIONS Figure 5-2. CoJag Board Schematic Diagram. Figure 5-3 Gun Board Schematic Diagram .. Figure 5-4 Coin Door Wiring Diagram. Figure 2-1 Select Test Menu Screen.......2.0cccce. 2-2 Figure 2-2. Adjust Volume Screen Figure 2-3. Statistics Screen....... Figure 2-4 Histograms Screen..... Figure 2-5 Game Options Screen TABLES

Figure 2-6 Coin Options Screen .. Table 1-1 Game Specifications ... 1-2 Figure 2-7 Controls Test Screen. Figure 2-8 Gun Test Screen Table 2-1 Summary of All Self-Test Screens........ 2-2 Table 2-2 Game Option Settings .. Figure 29 Disk Test Screen. igure BS ESE CTE Table 2-2 Coin Option Settings... Figure 2-10 Memory Tests Screen Figure 2-11 Monitor Te Figure 2-12 Color Test Screen............ Figure 2-13. Convergence Test Screen Figure 2-14 Purity Test Screen...... ts Screen ..... Table 3-1 General Troubleshooting .. Table 3-2 LED Indicators Troubleshooting ..... Table 3-3 Computer System Troubleshooting

Figure 4-1 Cabinet Overview, Front and Back Views Figure 4-2. Gun Assembly Figure 4-3 Over/Under Coin Door Assembly Figure 4-4 Electronics Tray Assembly Figure 4-5 Area 51 CoJag PCB Assembly .. Figure 4-6 Area 51 EC20X32 PCB Assembly. Figure 4-7 Area 51 Gun PCB Assembly.....

vi

Page 9

CHAPTER

Set-Up

How to Use This Manual

HIS MANUAL IS written for operators and service personnel. It provides information for setting up, playing, testing, and maintaining your Area 51™ game. Area 51 is a shooting game for 1- or 2players that has a unique look and cinematic style of play due to a combination of 3D computer generated graphics, digitized live action video, and stop-motion animation. Chapter 1 of this manual contains set-up and game play information. ¢ Chapter 2 contains a description of the self-test procedures and option settings. The self-test is important in the Area 51 game. You can troubleshoot the

printed-circuit boards (PCBs), main circuits, and controls using the screens in the self-test. You should

regularly test the boards and controls

with the self-test to keep your game in peak condition and at top earnings. @ Chapter 3 contains several troubleshooting tables, plus maintenance and repair procedures for the game components. If you have problems with your game, use this chapter to troubleshoot and repair it. Be sure to perform the preventive maintenance tasks to keep your game in good condition. ¢ Chapter 4 contains the illustrations and PCB parts lists. @ Chapter 5 contains the schematics for all the PCBs and all the wiring diagrams.

Page 10

Carrer 1— Set-Up @ Agra 51 Operator MANUAL

Operating the Game

To operate your game for maximum income, you should regularly run the self-test and check the controls with the Control Test and Sound Test in the self-test. By using the self-test regularly, you can find and fix problems immediately. This lets you keep your game in top condition.

Inspecting the Game

Characterist

Input Current ication Spe:

3 Amps at 120 V

102 to 132 VAC

5° to 38° C (37° to 100° F)

Not to exceed 95% relative

29.25

34 inches hes (75 cm) (67 om)

72 inches (183 cm) 825 lbs. (148 kg)

WARNING To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Make note of the power consumption when you set up this game, so that you do not overload your electrical circuit. See Table 1-1 for the power consumption and the other important specifications of this game. Inspect your Area 51 game carefully to ensure that the game is complete and was delivered to you in good condition. Inspect the cabinet as follows:

  • Examine the exterior for dents, chips, or broken parts.
  • Unlock and open the rear access door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows:

a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation.

d. Inspect the power supply. Check that the harness is plugged in correctly. Check that the green ground wires are connected.

1-2 Table 1-1 Game Specifications

e. Inspect other sub-assemblies, such as the video displays, controls, printed-circuit boards, and speaker. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch Locations

All of the controls are located on the back of the cabinet or behind the coin doors. The following describes the locations in more detail:

Power On/Off Switch

The power on/off switch is located near the bottom of the rear door.

Volume Control

There is no volume adjustment knob on any PCB in this game. Instead, volume is adjusted in the self-test software. The attract-mode and game-play volumes can be adjusted separately. Refer to Chapter 2 of this manual for more information.

Self-Test Switch

To perform the self test, open the upper coin door and activate the self-test switch mounted on a bracket located on the inside panel of the game cabinet.

Coin Counter

The coin counter is located below the coin box, inside the lower coin door.

Page 11

AREA 51 Operator's MANUAL & CHAPTER 1 — SET-UP

Video Display Controls

This game provides access to six of the most important video display controls — vertical and horizontal position, vertical hold, vertical size, black level, and contrast. To gain access to the video display controls, open the upper coin door. The control knobs are mounted on the inside panel of the game cabinet.

Setting the Coin and Game Options

The Area 51 coin and game options are set in the selftest. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Overview

This section describes the features and play of the Area 51 game.

Introduction

Area 51 is a shooting game for one or two players that has a unique look and cinematic style of play due to a combination of computer-generated graphics, digitized live-action video, and stop-motion animation.

Area 51’s Features

¢ Reliable controls, provided by Time Warner's own AccuAim targeting system, a custom-designed circuit that allows for very accurate performance.

  • Scoring enhancers and hidden features that will make Area 51 easy to learn but hard to master, ensuring long-lasting game depth.

Background The game is set at the fabled Area 51 military base in Nevada. One of the most top-secret military bases in the world, Area 51 is so top secret that as far as the government is concerned, it does not exist. There is a great deal of speculation about what actually takes place at Area 51, and more than a hint of conspiracy. While it is believed that many of the most advanced aircraft, including the SR-71 Blackbird and the Stealth Fighter were tested there, there are also rumors and testimonials by ex-employees that the government has captured alien spacecraft (UFOs) that are studied in a facility at the base. Other rumors hint at genetic studies of dead alien bodies, development of deadly biological warfare weapons, and nuclear weapons testing. Players are members of the STAAR Team (Special Tactical Advanced Alien Response), a secret paramilitary force who tackle dangerous jobs beyond the ability of the conventional military. As the game begins, the STAAR Team lands on the front tarmac of the air base and then they work their way through six security levels. Along the way, players must avoid being hit by armed enemies, helicopters, missiles, explosions, and deadly aliens. There are plenty of hidden weapons and surprises to help players out along the way. At first, players don’t know why they are being called in to destroy Area 51. As the game goes on, they realize that events at Area 51 have gotten horribly out of control. The personnel at the base are decaying into zombie-like creatures who are just the first stage in a horrible transformation, the end-stage of which is an amazing alien being who is fast, heavily armored, and equipped with deadly weapons.

Game Play

To win the game, players must play through all six levels of the game and beat the final end-game stage. To do this, they must pick up secret weapons and other power-ups hidden at various areas around the base Players must blast away all the obstacles in their path while avoiding hitting their fellow STAAR Team members.

To give the game a movie-like feel, the “camera” moves players around the base, with a pace that varies according to the wave. For some waves, the camera explores the environment slowly and methodically, while other waves have a faster tempo. In one wave, players are taken on a wild Jeep ride, careening around the complex and crashing into objects as they shoot enemies and avoid being shot themselves. Players also take rides on elevators, forklifts, and helicopters at strategic points in the game.

Players are encouraged to explore their environment by shooting everything in order to find the hidden features and reveal the scoring bonuses.

1-3

Page 12

Cuarter t

Page 13

CHAPTER 2

Self-Test

SE THE AREA 51” self-test to

check the condition of the

game circuitry and controls. You will see the self-test information on the video display and hear the sound test information through the speakers. You do not need any additional equipment to perform the self-test. Perform the self-test when you first set up the

game, each time you collect the

money, or when you suspect game problems. This chapter gy, shows the screens in the self- } ® test and explains each of the

tests. The screens and explanations are arranged in the order they appear in the self-test. Table 2-1

lists all the self-test screens.

Page 14

Cuaprer 2 — Setr-Test @ AREA 51 OPERATOR'S MANUAL

Entering and Exiting the Self-Test

The game's self-test switch is located behind the upper coin door. Turning it on causes the screen to enter the self-test mode. Doing so displays the Select Test menu; see Figure 2-1. Exit the self-test by turning off the selftest switch at any time.

It is likely that version numbers shown in the self-test screens in this manual will be different from those shown on your game. The functioning of the menus, however, will be the same.

Using the Gun

Either gun can be used in the self test menus to make selections or adjustments. A menu item can be selected by aiming the gun at it and then clicking the gun trigger. A menu item can be run by aiming the gun at it and clicking the trigger twice. The top, bottom, left, and right of the screens that are marked with arrows can be activated with the gun to move up and down the menu, to change selections, and to make adjustments (such as the game volume).

Select Test Menu

Adjust Volume

Statistics Statistics Histograms

Game Options

Coin Options

Controls Test

Gun Test

Disk Test

Memory Tests Color RAM Working RAM DRAM Bank 1 DRAM Bank 2 All RAM ROM Test

Monitor Tests Color Test Purity Test Convergence Test

Table 2-1 Summary of All Self-Test Screens

2-2

Choose which test or screen you want to run from this menu, shown in Figure & Table 2-1. Run the item by shooting it twice with a gun or by pressing the left start button to select it and then the right start button to run it.

SELECT TEST ) ~

ADJUST VOLUME STATISTICS GAME OPTIONS COIN OPTIONS CONTROLS TEST GUN TEST DISK TEST MEMORY TESTS MONITOR TESTS

To select test, use GUN To run test, Press right START SERIAL # “wg FGD32746

Figure 2-1 Select Test Menu Screen

Adjust the volume of the game using this screen, shown in Figure 2-2.

ADJUST VOLUME ~

23 45 67 8 9 10 11

ATTRACT

To RESTORE old Setting Press right START To ADJUST volume, Use GUN To save setting and exit, press left START w

Figure 2-2 Adjust Volume Screen The software plays continuous music to allow you to adjust both the game and attract-mode volume levels. The word GAME or ATTRACT flashes to show which of the two volumes levels you are adjusting. Fire the gun at the top or bottom of the screen to select between the two and to the left or right of the screen to adjust volumes. The attract-mode volume level has four steps: mute, 1/3, 2/3 or full volume level (these

Page 15

AREA 51 OPERATOR'S MANUAL @& CHAPTER 2 — SELF-TEST

are fractions of the game volume level). The manufacturer's suggested volume levels for a moderately noisy environment are GAME at 9 and ATTRACT at 2/3.

Statistics

Use the information shown in the statistics and histogram (bar graph) screens to keep track of your game use and maximize your profits. The game statistics are collected from the last time the statistics were cleared. Follow the instructions at the bottom of the screen to clear the statistics or to advance to the histogram screen.

Statistics Screen

The Statistics screen (see Figure 2-3) lists the following information:

  • Left Coins shows the number of coins counted in the left coin mechanism.
  • Right Coins shows the number of coins counted in the right coin mechanism.
  • Aux Coins shows the number of coins manually added by the operator (not inserted into any mechanism).

© Idle Minutes shows the number of minutes that the game was idle and not being played. Games Won shows the number of games that have been played to the finish. Total Sessions shows the number of different se: sions (new and continued games). A “session” is measured from the time the first player starts to play (from attract mode) to the time the last remaining player declines to continue. Any number of players may join or leave during a session. This statistic is intended to be a gauge of the “band wagon” effect, where players are attracted to join a game in progress.

Chow Palace, Head Quarters, Shake your Booda, and Egg-cellent show the number of times a secret room has been entered.

Cry mode shows the number of times that the Cry mode effect has been active.

Error count shows the number of errors counted in e ble memory. If the game consistently has an error count for several weeks, the PCB EPROM may need replacement Total Coins shows the number of coins counted in both left and right coin mechanisms. Average Time per Coin shows an average of the number of minutes played for every coin counted.

Percentage Play shows the ratio of game playing time to total time the game has been turned on.

Histogram Screens

  • 1-Player Minutes/2-Player Minutes shows the number of minutes that the game was played by one or two players. The Histograms screen is a menu that lets you display one of three screens (see Figure 2-4). These show horizontal bar graphs for new game times, continued game times, and session length

HISTOGRAMS ~

  • New Game Minutes shows the number of minutes played after starting a new game.
  • Continued Game Minutes shows the number of minutes played after continuing a game.

STATISTICS New Game Times {in seconds) Continued Game Times (in seconds) Session Length (in minutes) LEFT COINS RIGHT COINS CLEAR ALL HISTOGRAMS AUX COINS, IDLE MINS 1 PLAYER MINS 2 PLAYER MINS SESSION MINS NEW GAMES CONT GAMES GAMES WON TOTAL SESSIONS CHOW PALACE, HEAD QUARTERS, SHAKE YOUR BOODA EGG-CELLENT ERY MODE’ ERROR COUNT To select test, use GUN To run test, Press right START To return to menu, Press left START w TOTAL COINS AVG TIME/COIN PERCENTAGE PLAY

To clear ALL statistics Hold right START and press left START for more Statistics, Press left START Figure 2-4 Histograms Screen

Figure 2-3 Statistics Screen

2-3

Page 16

Cuaprer 2 — Seur-Test @ AREA 51 OPERATOR'S MANUAL

Game Option Avi Settings

End Game Looping Onv Off When set to On, the game will “loop” from the final screen back to the beginning screen. When set ‘to Off, the game ends at the final screen.

Game Difficulty

Provides a choice of 3 levels ¢ of game difficulty. Changing this setting

will reset ‘the High ‘Scores memory. Easy : Medium v Difficult

Gore s(n’ Of

Secret Room On Off Y

Reset h Scores Now Yes Turning gore off removes any animation with red blood

will reset ‘the High ‘Scores memory Turns on or off a room containing “Buddha” statues Using t the off

setting deletes the Buddha Room and replaces it with another secret room

Choosing Yes will reset all high scores (upon leaving the Game

Options Screen)

Reset Factory No v Yes

Options Choosing Yes will reset the game 10 the original factory settings (upon leaving the Game Options Screen) Number of Lives 3, 44 5, 6, or 7 Sets number of lives per credit Language Spanish French English ¥ Japanese German Chooses the language for the screen ‘text

v Manufacturer's recommended settings

Table 2-2 Game Option Settings

Ce Avi Option ble Settings

Free Play Now Yes Lets you choose free play to demonstrate the game: Discount to Continue No Yes” When set to Yes, this option reduces by 50% the player's cost to continue a game (always rounded up to the next full coin), Game Cost 1 coin 1 credit 2 coins 1 credit 3 coins 1 credit vw

Booins 1 credit” The number of coins required for one credit.

Bonus for Quantity Nonev Buy-in 2 coins give 1 3 coins give 1 3 coins give 2

9 coins give 2 9 coins give 3 Lets you choose from various kinds of bonuses or no bonus.

1 coin counts as 1 coin’ 1 coin counts as 2 coins Right Mech Value

1 coin counts as 7 coins 1 coin counts as 8 coins The number of coins each coin counts as as in the right coin mechanism

Left Mech Value 1 coin counts as 1 coin” 1 coin counts as 2 coins

1 coin counts as 7 coins 1 coin counts as 8 coins © The number of coins each coin counts as in the left coin mechanism

v Manufacturer's recommended settings

Table 2-3

2-4 Coin Option Settings

Page 17

Game Options

Check and select the game options on this screen, shown in Figure 2-5. The screen shows the factory default settings in green.

the gun to change the game options as desired. The game option settings, with defaults, are shown and explained in Table 2-2.

GAME OPTIONS ~ nd Game Looping on Game bitfculy: Medium a Gone: én Secret Room: Off

Reset High Scores: No Reset Factory Options No MORE BELOW to RESTORE old setting, press right START To SAVE setting and exit, Press left START ww

Figure 2-5 Game Options Screen

Coin Options

Check and select the coin options on this screen, shown in Figure 2-6. The screen shows the factory default settings in green.

Use the gun to change the coin options as desired The coin option settings, with defaults, are shown and explained in Table 2-3

COIN OPTIONS ~ Free Pl No

Discount to Continue: No

Game Cost: 2 Coins 1 Credit

Bonus for Quantity Buy-in:

Right Mech Value: 11Goin Counts as 1 Coin

Left Mech Value: 1 Coin Counts as 1 Coin To RESTORE old setting, press right START to SAVE setting and exit, Press left START w

Figure 2-6 Coin Options Screen

Controls Test

The controls test screen is shown in Figure 2-7. This test checks the pushbutton switches, the gun triggers. and the coin mechanisms.

CONTROLS TEST

COINS = AUXL x

START TRIGGER START TRIGGER x x x x

To return to menu, press and hold left START

Figure 2-7 Controls Test Screen

The X markings change to O markings each time a control is activated. If the changes do not occur, check the controls and their wiring.

Gun Test

The gun test screen is shown in Figure 2-8. This test checks and calibrates the guns

NOTE Well calibrated guns are important for player's enjoyment. Calibrate the guns often to keep the game at peak earnings.

CALIBRATE

‘Aim each gun at crosshair below

+

Hold trigger until flashing stops CALIBRATE For Tracking Screen, Press right START To return to menu, Press left START

Figure 2-8 Gun Test Screen

Page 18

Cuaprer 2 — Setr-Test 4 AREA 51 OPERATOR'S MANUAL

Each gun is calibrated separately. Hold one gun at a normal playing distance from the screen. Use the sights to aim the gun at the cross hairs on the screen. Press and hold the trigger until the screen stops flashing and the word “DONE” appears (in the same color as the gun that you are calibrating). The gun is now calibrated. Repeat the process with the other gun. Use the tracking screen to verify that the gun tracks evenly across the entire screen (with the exception of the edges, which are used as a buffer zone). Exit to the main menu to save the calibration settings.

Disk Test

Use the Disk Test s the hard disk.

If the “Hard Drive Connected:” display shows “No”, check that all of the cables going to the drive are secure sen, shown in Figure 2-9, to test

The test will continue running until the left start button is pressed. Normally, the “Status” of the drive will display as “Good”. If the “Status” displays “Bad”, check the cables going to the drive, then run the test again.

DISK TEST

Hard Drive Connected: Yes

Device Pointer: OxFFEO0000 Sector Pointer: OxFFOA7610

QUANTUM FIREBALL 1080A,

16 Heads 2112 Cylinders 63 SPT Head inder Status cyli Throughput 15 1265 Good 3999 kb/s

Tests completed: 000

AreaS1 1.0 October 31,1995

To return to menu, Press left START

Figure 2-9 Disk Test Screen

Memory Tests

Use this selection screen, shown in Figure 2-10, to run a memory test. These tests check the RAM and ROM chips. When the game power is turned on, the computer automatically runs through the random-access memory (RAM) tests. To bypass the startup RAM test, tap the right start button repeatedly. MEMORY TESTS

COLOR RAM WORKING RAM DRAM BANK 1 DRAM BANK 2 ALL RAM ROM TEST

To select test, use GUN To run test, Press right START To return to menu, Press left START

Figure 2-10 Memory Tests Screen

Monitor Tests

The monitor test selection screen (shown in Figure 2-11) lets you select from three screens — color, purity, and convergence. Advance to each screen to completely test the monitor.

MONITOR TESTS ~

COLOR BARS CONVERGENCE PURITY

To select test, use GUN To run test, Press right START To return to menu, Press left START w

Figure 2-11 Monitor Tests Screen

Color Test

The color test (see Figure 2-12) indicates the dynamic range of the video display color circuitry. The screen should show four bands (red, green, blue and white), ranging from dark to bright, from left to right. The red, green, and blue bands are produced by only one color gun being turned on in each band.

Page 19

AREA 51 OprRator's MANUAL @ CHAPTER 2 — SELF-Test

To remove border, press right START To return to menu, press léft START

Figure 2-12 Color Test Screen

Convergence Test

The convergence test has three screens — white, violet, and green backgrounds with grid lines. This sequence is then repeated but without any text on the screen. The green screen is shown in Figure 2-13. To see the remaining screens or return to the select test menu, follow the instructions shown at the bottom of the screen.

HTo change colors, press right START +jTo return to menu, press left STAR’

Figure 2-13 Convergence Test Screen Check the following on the screens:

  • The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel.
  • The convergence of the lines on the violet and green screens should be within 2.0 mm.

Purity Test

The next seven screens are color purity tests (see Figure 2-14). The entire screen will be red, green, blue, white, grey, “ones”, and black. The “ones” screen shows the lowest possible intensity of color (almost black). Press the right start button to change colors. The seven screens are also repeated without text, so that the entire screen can be checked. Each screen should show no unevenness of color and no lines in the display.

To change color, press right START To return to menu, press left START

Figure 2-14 Purity Test Screen If these screens do not meet these criteria, adjust the video display as described in the video display manual,

Page 20

Cuapren 2 ~ Senr-Test +

2-8

Page 21

CHAPTER 3

Troubleshooting

& Maintenance

HIS CHAPTER contains maintenance,

troubleshooting, and repair procedures for your Area 51” game. The mainte-

nance section gives information on cleaning the parts. The troubleshooting section contains several tables to help determine the EO source of a problem and the steps necessary to

repair it. The repair sec-

tion contains the steps nec-

essary to remove and install

the serviceable parts. Together, these three sections pro-

vide a complete guide to

servicing your Area 51”

game.

Page 22

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE & AREA 51 OPERATOR'S MANUAL

Maintenance Procedures

Troubleshooting Procedures

Introduction

This section describes the maintenance procedures for all of the major assemblies and components of the game. The maintenance procedures should be performed every 3—4 months on a regular basis.

WARNING Before performing any maintenance or repairs, please observe all of the following safety precautions:
  • Turn the game's power off.
  • Unplug the power cord from the electrical socket.
  • Secure loose clothing such as ties and long sleeves that could get caught within the game.
  • Remove all metal jewelry such as watches and necklaces that could conduct electricity from the game's power sources.

Cleaning Procedure for Coin

Mechanisms

Regular use of the coin mechanisms may result in a buildup of residue and dirt. If this is the case, clean the coin mechanism by following the steps below (refer to Figure 4-3 for detailed part information on the coin door).

  • Open the upper coin door.
  • Open the gate on the door that covers the magnet. Use the blade of a screwdriver to scrape away any metal filings that have collected on the magnet.
  • Clean the loose dust and dirt from the coin mechanism with a lint-free rag or a soft brush.
  • Clean the dirt and residue from the coin path with a toothbrush, Hot, soapy water may be used to help dissolve dirt and residue.
  • Blow out all the loose dirt and dry the coin mechanism with compressed air.
  • Close the gate on the door that covers the magnet and close the upper coin door.
CAUTION Never lubricate the coin mechanism with oil or grease.

This section is designed to help determine the source of a malfunction and provide detailed information on repairing the problem. Table 3-1 General Troubleshooting, is divided into two columns. The left-hand column is broken down into the general nature of problems. The right-hand column lists suggested solutions to solve the problem. Table 3-2 Area 51 PCB LED Indicators Troubleshooting, helps determine the cause of problems with the computer circuit boards or the hard disk drive by checking the status of the indicator LED's. The left-hand column lists the various states. The middle column explains the meaning of the state. The right-hand column suggests actions to correct a problem. Table 3-3 Computer System Troubleshooting, helps determine the cause of game operation problems. The lefthand column list symptoms. The middle column explains the probable cause of the symptom. The right-hand column suggests actions to correct a problem,

Repair Procedures

Introduction

This section describes the repair procedures for all of the major assemblies and components of the game. Before performing any repairs, use the tables in the Troubleshooting Procedures section and the screens in the Self Test software to help determine the source of the problem. The Maintenance Procedures section may also provide a good starting point for fixing many game problems before beginning what might be unnecessary repairs.

Speaker

Each game has a single speaker located in the middle of the control panel. The speaker provides the music and sounds for the game and self-tests. Failure of the speaker may result in distorted or no sound. If this is the case,

Page 23

AREA 51 OPERATOR'S MANUAL & CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

replace the speaker using the removal and installation steps below.

  • Remove the six screws securing the speaker grille; remove the speaker grille and set aside
  • Remove the four speaker mounting screws.
  • Disconnect the harness from the speaker.
  • Replace and reinstall the speaker in reverse order.

Attraction Panel Light Bulb

Use the light access door located on the top rear of the cabinet to replace the attraction panel light bulb.

  • Remove the two screws securing the light access door.
  • Unlock the access door and remove it.
  • Remove the cardboard bulb retaining clips one at a time by pressing on the circular tab and pulling the clip out.
  • Remove the bulb by rotating it and pushing it upwards.

Guns

To detach the gun and its cable for repair or replacement, use the following steps.

CAUTION Unplugging the guns from the wiring harness while the power is on can damage the PCB.

1, Open the upper coin door.

  • Disconnect the gun wire connector from the wiring harness.
  • Unfasten the the three flat washers and nuts that secure the gun cable mount.

Use the self test to calibrate the guns after installation.

System Logic Assemblies

This section describes the repair and maintenance procedures for the assemblies and components that are related to the system's logic and electronics, including the printedcircuit boards (PCBs) and the power supply. These components are mounted on the electronics tray and are accessed by opening the rear door.

Area 51 Game PCB Set

a The Area 51 game PCB set (board stack) is

responsible for the display graphics and game play. Failure of the game PCB set may result in erratic or no game play. If this is the case, repair or replace the game PCB set by following the removal and installation steps below.

  • Remove the four retaining screws securing the rear door.
  • Unlock the rear door and remove it.
  • Disconnect the harness connectors from the game PCB set. (There are 5 connectors in all.)
CAUTION Before handling static-sensitive components, properly ground yourself to discharge buildup of static charges.
  • Unfasten the three screws and spacers that secure the game PCB set to the electronics tray. Remove the game PCB set (refer to Figure 4-4.)
  • Re-install the game PCB set by following the previous steps in the reverse order.

Hard Disk Drive

a The hard disk drive unit stores the sound and

graphics information for the game program.

CAUTION Handle with Care! The hard disk drive can be damaged by a strong impact. Handle it gently to prevent damage. The hard disk drive can also be damaged by electrostatic discharge. Use the same precautions as used for the PCB.
  • Disconnect the ribbon and power cables from the disk drive.
  • Remove the four mounting screws that secure the disk drive to the mounting bracket.

Power Supply — Adjustment

CAUTION Adjust the power supply slowly to prevent over-voltage damage to the PCB. During adjustment, do not push the adjustment knob hard with the screwdriver, because it

The 5 volt power (supply) adjustment knob is located on the top of the power supply and can be turned with a small flat-blade screwdriver. If the power LED indicators show that the voltage needs to be adjusted (see Table 3-2), use the following procedure.

Page 24

Cuaprer 3 — TROUBLESHOOTING AND MAINTENANCE @ AREA 51 OPERATOR'S MANUAL

blem iuggested Action

Coin Mechanism Problem Check the wiring connections to the coin mechanism. Check the voltage to the + side of the mechanism. Test the coin mechanism with the Controls Test screen in the self-test.

Gun Problem wns

Check gun lens for dirt or blockage. Test the gun with the Gun Test screen in the self-test. Check the harnesses and connectors. If you took the gun apart, have you reassembled it correctly? Make sure all the parts of the gun are in good order. Repair or replace parts as needed. Check to see if any bright lights in the game area are interfering with gun operation. oO aon

Sound Problem

  • Check the speaker volume setting: make sure the volume isn't zero!
  • Test the sound with the Sound Test screen in the self-test.
  • Check the resistance of the speaker for 4 Ohms.

Video Display Problem

Screen is dark Check to see that the game is plugged in and powered on Check the line fuse if no power is present. Check the display brightness. Check the edge connector to the PCB. Check the harnesses and connectors to the video display PCB. Check the voltage levels to the video display PCB. Run through the following checklist. If you answer no to any question, you have a problem with the video display, not with the game circuitry. In this case, refer to your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have the correct voltage to the video display? NoOampwnpo

Only a colored screen appears Attempt to run a complete memory test in the self-test. Replace the ROM if a ROM failure is reported in the self-test N=

Picture wavers or is too small Check the voltage levels to the video display PCB. Check the B+ to the video display. (Refer to the video display manual. ) po

Picture is wavy Check the connection of the monitor ground wire to the monitor.

  • Check the connections of the sync inputs.
Picture is upside down or reversed1.If you replaced the monitor recently, check the horizontal or vertical yoke

wire connections to the video display. They may be switched.

Convergence, purity or color problems1.Use the self-test mode to digitally adjust the video display.
  • Use the adjustment procedures in your video display manual.
Picture is not centered1.Use the centering procedures in your video display manual

Table 3-1 General Troubleshooting

Page 25

AREA 51 OPERATOR'S MANUAL 4% CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

Meaning Action

DRIVE_BUSY (YELLOW — located near the hard disk cable) Flashing Intermittentiy Normal

Continuously OFFHard Disk not readingCheck the cables connected to the disk
Continuously ONHard Disk ErrorCheck the cables connected to the disk

Program WatchDog (GREEN — located near the four ROM chips on the top board) Continuously ON Normal

BlinkingROM problemCheck the program EPROM for bent pins

POWER (GREEN — located near the JAMMA connector) Continuously ON Normal

Continuously OFFNo power is reaching the boardCheck the power supply and cables

TOO_LOW (RED — located next to the power LED)

Continuously ONPower supply voltage too lowAdjust the power supply, as explained

in the Repair Procedures

TOO_HIGH (RED — located next to the power LED)

Continuously ONPower supply voltage too highAdjust the power supply, as explained

in the Repair Procedures

Table 3-2 LED Indicators Troubleshooting

  • If the TOO_HIGH LED is on, skip to step 2. Otherwise, slowly raise the voltage until the TOO_HIGH LED turns on.
  • Slowly lower the voltage until the TOO_HIGH LED turns off.

Power Supply — Replacement

A The power supply provides power to all of the

game assemblies that require it.

NOTE The power supply has no user-serviceable parts. Call your distributor for advance replacement. Return the power supply in an approved shipping container.

Failure of the power supply may result in erratic game play or no power at all. If this is the case, repair or replace the power supply assembly by following the steps below.

WARNING The power supply can contain high voltages even after the power switch is turned off. To avoid injury, observe all of the safety precautions before working on the power supply. (Refer to the Introduction in the Maintenance Procedures section.) 1, Remove the four retaining screws securing the rear door.

2, Unlock the rear door of the cabinet and remove it.

  • Disconnect the wiring harnesses from the power supply.
  • Unfasten the two screws securing the top bracket and remove it.
  • Unfasten the two screws that secure the power supply assembly to the cabinet, and remove the power supply assembly.
  • Re-install the power supply assembly by following the previous steps in the reverse order.

ROMs

a The ROMs contain the programming routines

used by the game PCB set to control game play. Replace the damaged ROMs by following the removal and installation steps below.

  • Remove the game PCB set according to the procedure in the Area 51 Game PCB Set section.
CAUTION Before handling static-sensitive components, properly ground yourself to discharge buildup of static charges.

3-5

Page 26

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE & AREA 51 OPERATOR'S MANUAL

Section/SymptomMeaningAction

Hard Disk/

“ZERO DIVISION” message at top of screenHard disk not connectedCheck the cables that connect the

hard disk to the game PCB.

EEPROM

"SETTING EEPROM DEFAULT VALUES"EEPROM badReplace the EEPROM.

message appears during every start & the high score table is empty

Table 3-3 Computer System Troubleshooting

2.Remove the damaged ROMs from the game PCB set3. Discharge the high voltage from the cathode-ray tube

using a chip extraction tool. (CRT).

3.Install the new ROMs by plugging them in the game——aaarr

PCB set sockets. NOTE

4.Re-install the game PCB set by following the steps inThe label on the video display assembly

the Area 51 Game PCB Set section in the reverse order. shows a circuit for discharging the high-voltage contained in the CRT to ground when Video Display the power is off. To repair, replace or make adjustments to the . . video display, follow the removal and installation a. Secure one end of a solid 18-gauge wire to a wellsteps below. insulated or wooden handle screwdriver.

  • —~ — b. Secure the other end of the wire to an earth
WARNING ground.
High Voltagec.Briefly touch the blade end of the screwdriver to

The video display contains lethal high volt- the CRT anode by sliding it under the anode cap. ages. To avoid injury, do not service this dis- d. Wait 2 minutes and repeat the previous step.

play until you observe all precautions nec-4,Disconnect all of the wire harnesses from the video

essary for working on high-voltage display. equipment.

X-Radiation5.Unfasten the three square-drive screws (on the top of
"3'oethecabiihatfronts|id

This video display is designed to minimize the cabinet) that secure the front shield and remove X-radiation. However, to avoid possible

exposure to soft X-radiation, never modify6.Unfasten the four flat washers and nuts that secure the

the high-voltage circuitry. video display chassis to the cabinet monitor mounting Implosion Hazard brackets.

The cathode-ray tube (CRT) may implode if7.Remove the video display assembly from the cabinet.

struck or dropped. The shattered glass from . _ _ the tube may cause injury up to six feet CAUTION away. Use care when handling the display and when removing it from the game cabinet. Also, wear gloves to protect your hands from the sheet-metal edges. Do not attempt to remove the video display without its chassis.

a _ 8, Install the new video display by following the previous steps (excluding steps 3a—3d.) in the reverse order.

  • Remove the four retaining screws securing the rear

door. . If necessary, adjust the new video display's brightness,

size, centering, purity and convergence according to

2.Unlock the rear door and remove it.the video display service manual.

3-6

Page 27

CHAPTER 4

Parts Illustrations

Part Ordering Information

HIS CHAPTER provides information you need to order parts for your game. The printed-circuit board (PCB) parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Time Warner Interactive Customer Service phone numbers are listed on the inside front cover of this manual.

Page 28

Cuarter 4 ~ Parts ILLUSTRATIONS AREA 51 OPERATOR'S MANUAL

178237-001 Red Button Assembly 160044001 Spat, 14/125 Vac, Gold, .187 QC Snap Switch

178398-001 Lamasaaeid Gun Holster Assembly " (Right) 75014-1040, S Blue Optic Gun Assembly 0.219 4500 mee) Fiat Washer Red Optic Gun Assembly dress 75-51208 Looknut 10-24 x1 1/4" Lg Bk Carriage Bolt 175014-1034 #10 x 218 X .625 Washer 177010-240 10x24 054673-01 Hex Locknut Speaker Grille i 176020-212 Digs see #8 x 9/4" Lo, Bik LPW Screw 178056-002 4/16" x 1/2" Wide Double Sided Foam Tape

054670-01 Display Shield

178201-004 3/4" Lime Green - T-Molding

  • 148027-001 items Not Shown: 6x9 Full Range
A054702-01051079-01Shielded Speaker

Shipping Container Assembly 3Amp. 176015-212

054644.01Slo-Biow Fuse Label#10 x 3/4" Dp Thd
Area 51 Wiring Diagram10002-0000Bik X-Rec Screw
‘A054647-01CoalEga1093-00;

Main Hamess Assembly 25" Service Manual oa/28 Gonna

A054817-01Neo-TecoeCoin Door

Component Bracket Assembly _A053502-01 141031-003 Video Hamess 054727-01 | 40" Id Ferrite Bead Nizn Clamp Assembly Front Panel Decal 150041-001 = 3.Ckt 79" 18 Awg Sit Alternate Video Displays: Set72-o Menih-si Control Panel Decal

‘Area 51 Operator Manual199022-501Assoz2en2
qae10e0014(Hantarex Polo)(Wells Gamer)

25" Color Raster 25” Color Raster Std Rees Display Std Res Display Disk Drive Service Tape 0s4698-01 (Extrusion) Shield Retainer 176020-212 #8 x 3/4” Lg. Bik LPW Screw

054731-01 Attraction Film

178237-005 Blue Button ‘Assembly 160044-001 Spdt, 14/125 Vac, Gold, 187 QC Snap Switch

Figure 4-1 Cabinet Overview, Front and Back Views A054731-01 ‘A054700-01 Fluorescent Lamp Fixture Assembly 76018-112 #10 x 3/4", Dp Tha X-Rec Screw 170003-001 18", 15Watt Fluorescent Lamp 178232-001 1 TeT12 Lamp Retaining Clip

05467101 Mounting Display Bracket 175017-2025 4/4" Zine Split-Lock Washer 175014-1050 1/4" 281 x 625 Zine Fiat Washer 72-5520 114-20 x 1.25 Lg. Hex Screw

Page 29

AREA 51 OPERATOR'S MANUAL @ CHAPTER 4 — Parts ILLUSTRATIONS

054654-01 Light Access Door 176020-220 8x1 1/4" Lg. Bik LPW Screw 178198-002 - 11/2" x 3/82" Off-Set Cam 178197-001 Lock and Key Assembly 178276-002 ‘Anchor Wood Washer

054730-04 Upper Right Side Panel Decal

‘A054705-01 Area Si Electronics Tray Assembly 176020-220 #8x1 1/4" Lg. Bik LPW Screw 17026-0038 8-32 Nut Washer ‘Assembly A054649-01 Display Power Hamess Assembly

043939-01 Leg Leveler Plate 178255-004 318-16" x 1.50" Adjustable Glide 176015-112 #10 x 3/4" LG Deep Thread Pan Head Screw ~ Lower Right Side Panel Decal

038158-01 Id. Non ULL. Product Label

039450-01 FCC Compliance Label

Items Not Shown:

‘A053502-01 Video Hamess Assembly 178032-002 #10 Wire & Cable Tie 054730-01 Lower Lett Side Panel Decal 054730-03, Upper Left Side Panel Decal 037332-01 Louvered Vent Grill 178129-001 Wire Routing Clip 176018-001 #10. 3/4 LG SQ Dr. Tapping Screw

139022-505 Std Res, Neotec 25" Color Raster Display, 72-5520 114-20 x 1.25 LG Hex Screw 175017-2025 1/4" Zinc Split-Lock Washer 175014-1050 V/A" 281 x .625 Zinc Flat Washer 17026-0044 1/4-20 Nut Washer ‘Assembly 72-6128 #6.x 3/4" AB X-Rec Pan Screw

054676-01 Power Supply Bracket 176015-110, #10 x 5/8 Dp Thd. X-Rec Screw

149015-003 Volt, 20Amp / 12Volt, BAP |_| AT Power Supply Switching 176015-110 #10 x 5/8, Dp Thd. X-Rec Screw

042452-01 FBI Warning Label

049514-01 Ul Label bagel Rear Door | 038086-01 ‘Shock Waring Label 176020-220 #8 x 11/4" Lg. Blk LPW Screw ‘$T-402 Area 51 Self Test Label 178198-002 11/2" x 3/32" Off-Set Cam 178197-001 Lock and Key Assembly 178276-002 | Anchor Wood Washer

Figure 4-1 Cabinet Overview, Front and Back Views, Continued

A054731-01

Page 30

CHapTer 4 — Parts ILLusTRATIONS AREA 51 OPERATOR'S MANUAL

175003-001 (A051987-01 125 x 250 Nylon |. i Gun PCB Assembly Flat Washer) | 99-215122 | 99-215126 Trigger Spring 4-40 x25 Type 23-—— Pan Head Screw 178386-001 18.5mm Dia. 100mm Effective Focal Length Bi-Convex Lens

99-215121 | Black Trigger ‘99 | 99-215129 -—1 6-32 x 38 T-10 | TORX Screw

P

99-215125|ge-2ts124
Blue Left Half|_|Blue Right Halt
Optical Gun|| Optical Gun

OR L__| or 99-215131 99-215130 Red Left Half | Red Right Hatt Optical Gun | | Optical Gun

99-215127 | if | 99-215123, #2x12TypeB— ibelid Phillips Pan-Hd. | Switch mbly if Screw

| 99-215128 | 6-32 .25 AF slack Hex Nut

99-215132 Harness and Stop Plate Gun Hose Assembly

Figure 4-2 Gun Assembly A054890-01 (blue), A054890-02 (red)

4-4

Page 31

AREA 51 OprRavor's MaNuaL @ CHAPTER 4 — PARTS ILLUSTRATIONS

99-15038 99-15036 Bezel for Button Cover

99-15001 thru 99-15012 > Retum Button z

99-15039 Bezel for Cover 99-15125 by Frame Hinge Screw —

99-15052 Spring for Button

99-15110 99-1508 Enclosure ‘Clamp

99-15135 Frame Clamp Screw

99-15116 Upper Door

99-15115, Lower Door

99-15114 Die Cast Frame

99-15111 Coin Counter

99-15089 99-15127 99-15109 a

Lock Assy ‘Galil Box Meter Mounting

Figure 4-3 Over/Under Coin Door Assembly

171093-001 (This figure is continued on next page)

Page 32

Caper 4 — Parts ILLUSTRATIONS AREA 51 OPERATOR'S MANUAL

99-15025 ___|99-15086 i cag Peto Left Coin inlet Coin Mechanism W/Pivot & Stud

99-15113| Key Hook

99-15056 ‘Screw for Bezel

99-15096 Switch Adjuster

99-15056 | - Screw 99-15100 Lamp

99-15026 Right Coin inlet 99-15131 Elastic Locknut | 99-15132 Snap-on Sleeve

99-15130 Snap-on Clip

99-15133 | Hold Down Bracket

99-15056 ‘Screw for Bezel 99-15128 | NutWasher for — M/S Mounting Screw 99-15027 | | Coin Ret. Plate |

|99-15028 | Coin Return Box

___}99-15056 | Screw for Bezel 99-15129| Mounting Stud - (2 places)

9015051; | _____99-15134 Lamp Holder | |4-40-1" Pan-Head Screw

1 lat-Heac —_ Mounting Screw

9915042) _ ___99-15085

Switch Coin Door Hamess

Figure 4-3 Over/Under Coin Door Assembly 171093-001

Page 33

AREA 51 Operator's MANUAL @ CHAPTER 4 — PARTS ILLUSTRATIONS

171138-1080 3.5" 1080 MB (Quantum) Hard Disk Drive 178382-002 75G impact Indicator items Not Shown:

A054819-01 Ground Braid Assembly

Alternate Disk Drives: 171138-1081 3.5" 1080 MB (Seagate) Hard Disk Drive 171138-1082 3.5" 1080 MB (IBM) Hard Disk Drive

172025-3604 6-32 x 25” Long X-Rex Pan Head Screw |

A054818-01 Ribbon Cable Assembly

054900-01 | Hard Drive Label

054667-01 | Electronics Tray Assembly 176015-112 4410 x 3/4" Long X-Rec Pan Head Screw

(054675-01 -Hard Drive | Mounting Bracket

  • : /054813-01 ~ = ——| Ground Plate 176015-112 | #10 x 3/4" Long X-Rec Pan Head Screw

172025-3605

  • om 6.82 312" Long X-Rec Pan Screw

A054711-01 | Area 51 PCB Assembly 176015-112 #10x 3/4" LE _ X-Rlec Pan-Head Screw —= —| 175008-002 | 20x 54 x.187" | Nylon Flat Washer

102058-001 ~~~) 4x6" 1.7# Anti-Static Polyethylene Foam

Figure 4-4 Electronics Tray Assembly A054705-01

4-7

Page 34

Cuaprer 4 — Parts Intustrations @ Ana 51 OPERATOR'S MANUAL

TOP SIDE

° sue Coy °

ae & a4 F

7 a w) [os 7 a]: [ae 3 fecal

LYCominieieESas _]s (l=
18?we](_)Le
sen20"Ea”
=7H7*aw 6

fo}

yi SWEA 20EB

“Te

yovoweR

Figure 4-5 Area 51 Cojag PCB Assembly (Top Side) A053538-02

4-8

Page 35

AREA 51 OPERATOR’s MANUAL CHAPTER 4 — PARTS ILLUSTRATIONS

BOTTOM SIDE

| “8 a

_— « 7

:

4a a 5

1 tan 2 $_ =

' aoe ot -2 2 = Ey

= 3 ora

| ; 3 Zoo | -<

Figure 4-5 Area 51 CoJag PCB Assembly (Bottom Side) A053538-02

Page 36

CHAPTER 4 — PARTS ILLUSTRATIONS @ AREA 51 OPERATOR'S MANUAL

Area 51 Cojag PCB Assembly Parts List

Desig- Desig-

nator __ DescriptionPart No.nator_DescriptionPart No.
19F/JSocket, 8 Pin, 300, Dbl Wipe179356-030823EIC, 741814, $014.15137056-0001
(HS1)Screw, Pan, 4-40X3/8, Xrec, Zinc172025-3206BConn, Receptacle, 2-Ckt179178-002
GSP1)Conn, Rept, 2-Ckt179178-002
(XBUS)Shroud, 96 Pos, Pinless179369-0096C1-C6Capacitor, Chip, 1000 pF, 50 V,

Ceramic, 1206 125001-0102

1R,1SIC, 74F245, $020.3137591-00017Capacitor, 100 pF, 16 V, Electrolytic,
2Conn, Receptacle, 2-Ckt179178-002Radial123013-107
2FIC, AK4310, VSOP24137744-002csCapacitor, 1000 pF, 16 V, Electrolytic 123031-108
3AIC, TDA1554137733-001coCapacitor, 100 pF, 16 V, Electrolytic,

Radial 123013-107

3EIC, TEA6320T, $032.3137800-0001
4Conn, Receptacle, 2-Ckt179178-002C10, C11Capacitor, Chip, .012 pF, 50 V,
4N, 4P, 4R IC, DRAM, 256KX16, 70 ns, SO}40—_137751-070Ceramic, 1206125002-0123
5F,6FIC, 74F74, $014.15137436-0001c12Capacitor, Chip, .1 pF, 50 V,

Ceramic, 1206 125003-0104

orIC, 74F245, $020.3137591-0001c13Capacitor, Chip, 1000 pF, 50 V,
JEIC, Quad Op-Amp, MC3403D, SO14.15Ceramic, 120612501-0102
137673-1001ci4Capacitor, Chip, 100 pF, 50 V,
TN, 7P, 7R IC, DRAM, 256KX16, 70 ns, SOJ40_—137751-070Ceramic, 120612501-0101
8IC, 74F245, $020.3137591-0001
C15-C17__Capacitor, 270PFC, 50 V, EMI Filter140006-271
oFIC, 74HCT245, $020.3137791-0001C18-C21Capacitor, Chip, .1 pF, $0 V,
10KIC, CPU, Tom, QFP208137785-001Ceramic, 1206125003-0104
10N,10P,10R IC, DRAM, 256KX16, 70 ns, SOJ40—137751-070€22-€25Capacitor, Chip, .012 pF, 50 V,
10TIC, 74F245, $020.3137591-0001Ceramic, 1206125002-0123

€26-C29 Capacitor, Chip, .1 pF, 50 V,

1FIC, 74HCT245, $020.3137791-0001Ceramic, 120612503-0104
11TIC, 74F245, $020.3137591-0001
13FIC, 74HCT245, $020.313791-0001C30, C31Capacitor, Chip, 1000 pF, 50 V,
13N,13P,13R IC, DRAM, 256KX16, 70 ns, SOJ40—_-137751-070Ceramic, 120612501-0102

€32-C57_ Capacitor, Chip, .1 pF, 50 V,

14MIC, 74F06, $014.1513789-0001Ceramic, 1206125003-0104
4IC, 74F245, $020.3137591-000158Capacitor, 10 pF, 25 V, Electrolytic124009-106
15FIC, 74F00, $014.15137327-000159Capacitor, 1000 pF, 16 V, Electrolytic 123031-108
16KIC, DSP, Jerry, QFP160137785-002

C60, C61 Capacitor, Chip, .22 pF, 50 V,

16MIC, 74F273, $020.3137610-1001Ceramic, 1206125003-0224
16P, 16SIC, 74F245, $020.3137591-0001C62Capacitor, 1 pF, 50 V, Electrolytic,
17BIC, LM613137746-001Radial123001-105
17FIC, 74F02, $014.15137481-0001C63Capacitor, Chip, .22 pF, 50 V,

Ceramic, 1206 125003-0224

18M, 18P,18S IC, 74F245, $020.3137591-0001C64Capacitor, Chip, .047 pF, 50 V,
20A, 20BIC, 7418257, $016.15137136-0001Ceramic, 1206125002-0473
20cIC, 74F06, $014.15137789-0001
20DIC, 7418273, $020.3137040-0001C65Capacitor, Chip, .012 pF, 50 V,

Ceramic, 1206 125002-0123

20EIC, 74F32, $014.15137486-0001C66Capacitor, Chip, .047 pF, 50 V,
20P,20R,20 IC, 74F245, $020.3137591-0001Ceramic, 1206125002-0473
22A, 22B, 22C, 22D67Capacitor, 1 pF, 50 V, Electrolytic,
IC, 7418257, $016.15137136-0001Radial123001-105
22FIC, VT83C461, QFP100137799-0001C68Capacitor, Chip, 5600 pF, 50 V,

Ceramic, 1206 125002-0562

Page 37

AREA 51 OPERATOR'S MANUAL CHAPTER 4 — PARTS ILLUSTRATIONS

Area 51 Cojag PCB Assembly Parts List, Continued

Desig- Desig-

natorDescriptionPart No.natorDescription
69Capacitor, Chip, .033 pF, 50 V,c102Capacitor, Chip, .1 pF, 50 V,
Ceramic, 1206125002-0333Ceramic, 1206125003-0104
c70Capacitor, Chip, .22 pF, 50 V,C103Capacitor, Chip, 100 pF, 50 V,
Ceramic, 1206125003-0224Ceramic, 1206125001-0101
c71Capacitor, Chip, .150 pF, 50 V,C104Capacitor, Chip, .1 pF, 50 V,
Ceramic, 1206125003-0154Ceramic, 1206125003-0104

c72 Capacitor, 1000 pF, 16 V, Electrolytic 123031-108

C105Capacitor, 10 pF, 25 V, Electrolytic124009-106
C73Capacitor, 100 pF, 35 V, Electrolytic,C106Capacitor, Chip, 47 pF, 50 V,
Radial123009-1014Ceramic, 1206125001-0470
C74, C75Capacitor, Chip, .33 pF, 50 V,C108Capacitor, 10 pF, 25 V, Electrolytic124009-106
Ceramic, 1206125003-0334€109, C110 Capacitor, Chip, .012 pF, 50 V,
C76Capacitor, 47 uF, 50 V, Electrolytic123015-476Ceramic, 1206125002-0123

c77 Capacitor, 10 pF, 35 V, Electrolytic,

Radial123000-106ciCapacitor, Chip, .1 pF, 50 V,

Ceramic, 1206 125003-0104

78, C79Capacitor, Chip, .1 pF, 50 V,cu2Capacitor, Chip, 1000 pF, 50 V,
Ceramic, 1206125003-0104Ceramic, 1206125001-0102
80Capacitor, Chip, 5600 pF, 50 V,c13Capacitor, Chip, 100 pF, 50 V,
Ceramic, 1206125002-0562Ceramic, 1206125001-0101
C81Capacitor, Chip, 033 pF, 50 V,ci4Capacitor, Chip, 1000 pF, 50 V,
Ceramic, 1206125002-0333Ceramic, 1206125001-0102

c82 Capacitor, Chip, 8200 pF, 50 V,

Ceramic, 1206125002-0822€115-C117 Capacitor, Chip, .1 pF, 50 V,

Ceramic, 1206 125003-0104

C83Capacitor, Chip, .150 pF, 50 V,C118-C121 Capacitor, Chip, .012 pF, 50 V,
Ceramic, 1206125003-0154Ceramic, 1206125002-0123
84Capacitor, 10 pF, 35 V, Electrolytic,€122-C133 Capacitor, Chip, .1 uF, 50 V,
Radial123000-106Ceramic, 1206125003-0104
C85Capacitor, 1000 pF, 16 V, Electrolytic 123031-108C134Capacitor, Chip, 8200 pF, 50 V,
C86Capacitor, 10 pF, 35 V, Electrolytic,Ceramic, 1206125002-0822

Radial 123000-106 C135 Capacitor, Chip, .012 pF, 50 V,

c87Capacitor, Chip, .1 pF, 50 V,Ceramic, 1206125002-0123
Ceramic, 1206125003-0104C136-C146 Capacitor, Chip, .1 pF, 50 V,
€88, C89Capacitor, Chip, .22 pF, 50 V,Ceramic, 1206125003-0104
Ceramic, 1206125003-0224c147Capacitor, Chip, .22 pF, 50 V,
90Capacitor, Chip, .33 pF, 50 V,Ceramic, 120612503-0224
Ceramic, 1206125003-0334C148-C158, C161-C171, C173, C175-C278
colCapacitor, Chip, .1 pF, 50 V,Capacitor, Chip, .1 pF, 50 V, Cer. 1206 125003-0104

Ceramic, 1206 125003-0104

CRI-CR4_Diode, 1N4001131048-001
cozCapacitor, Chip, .33 pF, 50 V,CRSDiode, 1N5818131025-001
Ceramic, 1206125003-0334CROLED, Yel, T1-3/4, Diffused,
©93Capacitor, Chip, .1 pF, 50 V,25-MCD, 40-Deg138016-001

Ceramic, 1206 125003-0104

C94-C96Capacitor, Chip, .047 pF, 50 V,«G)Conn, Receptacle, 2-Ckt179178-002
Ceramic, 1206125002-0473GND1-4Test Point179051-001

co7 Capacitor, 1 pF, 50 V, Electrolytic,

Radial123001-105HDPOWER Conn, 4-Ckt, Hdr, .200 Ctr179310-004
HS1Heat Sink, Alum, 2X2X1, 2X4-40178378-001
C98-C100 Capacitor, Chip, .047 pF, 50 V,JGUN1, 2 Conn, 9-Ckt, Hdr, 100 Ctr, Key 6—_179118-009
Ceramic, 1206125002-0473JIDEBConn, 40-Ckt, Hdr, 2X20, Low Prof.179261-040

4-11

Page 38

Cuaprer 4 — Parts ILLUSTRATIONS @ AREA 51 OPERATOR'S MANUAL

Area 51 Cojag PCB Assembly Parts List, Continued

Desig- Desig-

nator_DescriptionPart No.nator_DescriptionPart No.
JPLY3,4Conn, 15-Ckt, Hdr, .100 Ctr179118-015R93Resistor, Chip, 12 Q, #5%, 1/8 W, 1206 112006-0120
JPWRConn, 9-Ckt, Hdr, .156 Ctr, Rt, Key 3. 179165-009R94Resistor, Chip, 10 Q, +5%, 1/8 W, 1206 112006-0100

R95 Resistor, Chip, 75 Q, +5%, 1/8 W, 1206 112006-0750

JSP1-JSP4 Conn, 3-Ckt; Hdr, .100 Ctr179048-003R96Resistor, Chip, 100 Q, #5%, 1/8 W, 1206 12006-0101'
JSPKRConn, 11-Ckt, Hdr, .100 Ctr, Key 5179118-011
JSYNCConn, 3-Ckt, Hdr, .100 Ctr179048-003ROTResistor, Chip, 1 KQ, £5%, 1/8 W, 1206 112006-0102
JVCRConn, 3-Ckt, Hdr, .100 Ctr179048-003R98Resistor, Chip, 2.4 KO, 45%, 1/8 W, 1206 112006-0242

R99-R104__ Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 11206-0102

JVUPDNConn, 3-Ckt, Hdr, .100 Ctr179048-003R105Resistor, Chip, 470 Q, 45%, 1/8 W, 1206 112006-0471
JWELLSBConn, 3-Ckt, Hdr, .100 Ctr179048-003
JWELLSGConn, 3-Ckt, Hdr, .100 Ctr179048-003R106Resistor, Chip, 12 Q, #5%, 1/8 W, 1206 112006-0120
JWELLSRConn, 3-Ckt, Hdr, .100 Ctr179048-003R107Resistor, Chip, 10 Q, #5%, 1/8 W, 1206 112006-0100

R108 Resistor, Chip, 75 Q, #5%, 1/8 W, 1206 112006-0750

JWELLSRConn, Receptacle, 2-Ckt179178-002R109Resistor, Chip, 100 Q, 45%, 1/8 W, 1206 112006-0101

JXBUS Conn, 96-Ckt, Recep., Pressfit, Long 179368-0096

JXCLKTRM Conn, 2-Ckt, Hdr, .100 Ctr179048-002R110Resistor, Chip, 1 KQ, £5%, 1/8 W, 1206 112006-0102

Ril Resistor, Chip, 2.4 KQ, +5%, 1/8 W, 1206 112006-0242

L1-L6Inductor, Ferrite Bead, 1206141032-0001R112Resistor, Chip, 20 Q, #1%, 1/8 W, 1206 112002-0200
113-121Inductor, 600 Q, 1206141032-0002R113Resistor, Chip, 470 Q, #5%, 1/8 W, 1206 112006-0471
POWERLED, Grn, MV5453, T1-3/4,R114Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 12006-0102
20-MCD, Wide138020-001R115Resistor, Chip, 470 Q, +5%, 1/8 W, 1206 112006-0471

R116 Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

Q1-Q4Transistor, 2N5306133033-001RU7Resistor, Chip, 12 Q, +5%, 1/8 W, 1206 112006-0120
Q5-Q7Transistor, 2N3904133041-001
38IC, 78109137740-002R118Resistor, Chip, 10 Q, #5%, 1/8 W, 1206 112006-0100
QoIC, 78105137258-001R119Resistor, Chip, 75 Q, +5%, 1/8 W, 1206 112006-0750

R120 Resistor, Chip, 100 Q, #5%, 1/8 W, 1206 112006-0101

RIResistor, Chip, 1 KQ, #5%, 1/8 W, 1206 112006-0102R121Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

R2,R3—_Resistor, 0 Q, £5%, 1/4 W 110005-001

R4,R5 —_ Resistor, Chip, 470 Q, +5%, 1/8 W, 1206 112006-0471R122Resistor, Chip, 2.4 KQ, £5%, 1/8 W, 1206 112006-0242
R6Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102R123-R125 Resistor, Chip, 39 KQ, +5%, 1/8 W, 1206 12006-0393

R126 Resistor, Chip, 0 Q, +5%, 1/8 W, 1206 112006-0001

R7-R15 __ Resistor, Chip, 470 Q, #5%, 1/8 W, 1206 112006-0471R127Resistor, Chip, 330 Q, 45%, 1/8 W, 1206 112006-0331

R16-R27___ Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

R28-R40__Resistor, Chip, 470 Q, #5%, 1/8 W, 1206 112006-0471R128Resistor, Chip, 1 KQ, #5%, 1/8 W, 1206 112006-0102
R41-RO6Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102R129Resistor, Chip, 330 Q, #5%, 1/8 W, 1206 112006-0331

R130, R131 Resistor, Chip, 1 KQ, #5%, 1/8 W, 1206 12006-0102

R67-R75__Resistor, Chip, 470 Q, #5%, 1/8 W, 1206 112006-0471R132Resistor, Chip, 330 Q, 45%, 1/8 W, 1206 12006-0331

R76 Resistor, Chip, 1 KQ, £5%, 1/8 W, 1206 12006-0102

R77Resistor, Chip, 470 Q, #5%, 1/8 W, 1206 112006-0471R133Resistor, Chip, 1 KQ, £5%, 1/8 W, 1206 112006-0102
R78Resistor, Chip, 20 KQ, +5%, 1/8 W, 1206 112006-0203R134Resistor, Chip, 100 KQ, #1%, 1/8 W, 1206 12002-1003

R137, R138 Resistor, Chip, 11.0 KQ, +1%, 1/8 W, 1206 112002-1102

R79Resistor, Chip, 2.2 KQ, £5%, 1/8 W, 1206 12006-0222R139Resistor, Chip, 20 KQ, £5%, 1/8 W, 1206 112006-0203

R80, R81 _ Resistor, Chip, 100 KQ, #1%, 1/8 W, 1206 12002-1003

R82-R84_—_Resistor, Chip, 45.3 KQ, +1%, 1/8 W, 1206 12002-4532R140Resistor, Chip, 2.2 KQ, #5%, 1/8 W, 1206 12006-0222
R85Resistor, Chip, 10 KQ, #5%, 1/8 W, 1206 112006-0103R141, R142 Resistor, Chip, 22.6 KQ, +1%, 1/8 W, 1206 112002-2262

R143 Resistor, Chip, 330 Q, +5%, 1/8 W, 1206 112006-0331

R88Resistor, Chip, 100 KQ, +1%, 1/8 W, 1206 112002-1003R144Resistor, Chip, 10 Q, 5%, 1/8 W, 1206 12006-0100

R89 Resistor, Chip, 47 KQ, +5%, 1/8 W, 1206 112006-0473

R90Resistor, Chip, 22.6 KQ, #1%, 1/8 W, 1206 112002-2262R145-R149 Resistor, Chip, 47 Q, +5%, 1/8 W, 1206 11206-0470
R91, R92Resistor, Chip, 45.3 KQ, +1%, 1/8 W, 1206 112002-4532R150Resistor, Chip, 220 Q, #5%, 1/8 W, 1206 112006-0221

RISL Resistor, Chip, 2.2 KQ, #5%, 1/8 W, 1206 112006-0222

4-12

Page 39

AREA 51 OPERATOR'S MANUAL @ CHAPTER 4 — PARTS ILLUSTRATIONS

Area 51 Cojag PCB Assembly Parts List, Continued

Desig- - 7 nator _Description Part No. Designator _ Description Part R152-R155, R158-R160 Resistor, Chip, 33 Q, +5%, 1/8 W, 1206 112006-0330

R1G1-R163, R165 Resistor, Chip, 10 KQ, 45%, 1/8 W, 1206 112006-0103 R166, R167 Resistor, Chip, 2.2 KQ, +5%, 1/8 W, 1206 112006-0222 R168-R170 Resistor, Chip, 33 Q, +5%, 1/8 W, 1206 112006-0330 R172 Resistor, Chip, 2 KQ, +5%, 1/8 W, 1206 112006-0202 R173, Resistor, Chip, 1 KQ, 45%, 1/8 W, 1206 112006-0102 R174 Resistor, Chip, 2 KQ, +5%, 1/8 W, 1206 112006-0202 R175, R176 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103 R177, R178 Resistor, Chip, 2.2 KQ, +5%, 1/8 W, 1206 112006-0222

R179 Resistor, Chip, 330, +5%, 1/8 W, 1206 112006-0331 R180 Resistor, Chip, 1 KQ, 45%, 1/8 W, 1206 112006-0102 RI81 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103 R182, R183 Resistor, Chip, 1.2 KQ, 5%, 1/8 W, 1206 12006-0122

R184 Resistor, Chip, 100 Q, +5%, 1/8 W, 1206 112006-0101 R185 Resistor, Chip, 4.7 KQ, +5%, 1/8 W, 1206112006-0472 R186 Resistor, Chip, 100 Q, +5%, 1/8 W, 1206 112006-0101 R187—R194 Resistor, Chip, 47 Q, +5%, 1/8 W, 1206 112006-0470

R195 Resistor, Chip, 220 Q, +5%, 1/8 W, 1206 112006-0221 R196-R219 Resistor, Chip, 33 Q, +5%, 1/8 W, 1206 112006-0330 R220 Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102 R221, R222, R224-R232 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103

R233, Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102 R234 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103 R235 Resistor, Chip, 4.7 KQ, +5%, 1/8 W, 1206 112006-0472 R236 Resistor, Chip, 300 Q, +5%, 1/8 W, 1206 112006-0301

R237 Resistor, Chip, 4.7 KQ, +5%, 1/8 W, 1206 112006-0472 R238-R242 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206112006-0103 R243 Resistor, Chip, 470 Q, +5%, 1/8 W, 1206112006-0471 R252-R264 Resistor, Chip, 33 Q, +5%, 1/8 W, 1206 112006-0330

R265-R267 Resistor, Chip, 10 KQ, #5%, 1/8 W, 1206 112006-0103 R268-R271 Resistor, Chip, 33 Q, +5%, 1/8 W, 1206 112006-0330 R272-R276 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103 R277 Resistor, Chip, 220 Q, 45%, 1/8 W, 1206 112006-0221 R278, R279 Resistor, Chip, 330 Q, +5%, 1/8 W, 1206 112006-0331 R280 Resistor, Chip, 2 KQ, £5%, 1/8 W, 1206 112006-0202 R281 Resistor, Chip, 4.7 KQ, 45%, 1/8 W, 1206 112006-0472 R282 Resistor, Chip, 47 Q, 45%, 1/8 W, 1206 112006-0470

R286 Resistor, Chip, 10 Q, +5%, 1/8 W, 1206 112006-0100 R287-R289 Resistor, Chip, 4.7 KQ, +5%, 1/8 W, 1206 112006-0472 R290-R301 Resistor, Chip, 470 Q, +5%, 1/8 W, 1206 112006-0471 R302-R312 Resistor, Chip, 1 KQ, 5%, 1/8 W, 1206 112006-0102

R313, R314 Resistor, Chip, 45.3 KQ, £1%, 1/8 W, 1206 112002-4532 R317-R324 Resistor, Chip, 47 Q, +5%, 1/8 W, 1206 112006-0470 R325 Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102 R329 Resistor, Chip, 100 Q, +5%, 1/8 W, 1206 112006-0101

R330 Resistor, Chip, 470, +5%, 1/8 W, 1206 112006-0471 R340 Resistor, Chip, 4.7 KQ, +5%, 1/8 W, 1206 112006-0472 R341 Resistor, Chip, 2 KQ, +5%, 1/8 W, 1206 112006-0202 R342 Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

R343 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103 R344-R347 Resistor, Chip, 22 Q, +5%, 1/8 W, 1206 112006-0220

RNI-RN3_ Resistor Network, R2R10, 1K/2 KQ, SIP10 118015-001

SELFTEST Switch, Slide, SPDT 160040-001

SPARESocket, 24 Pin, .300, Dbl Wipe179356-0324

TOO_HIGH LED, Red, T1-3/4, Diffused, 5MCD, 80-Deg 138021-001 TOO_LOW LED, Red, T1-3/4, Diffused, .5MCD, 80-Deg 138021-001

x1 Crystal, 52.000 MHz, Osc. Module, .3X.6DIP 144008-012

X2Crystal, 14.318 MHz, Osc. Module144008-001
HS1COMPOUND, THERMAL107031-001
Page 40

Cuaprer 4 — Parts ILLUSTRATIONS @ AREA 51 OPERATOR'S MANUAL

4-14 Wioxe— — = — H “3ROMBUS.

ar D R37

yer ® axBuSOFF 1 lp a

R26 c10 i Res

3x8US96

Figure 4-6 Area 51 EC20X32 PCB Assembly A053448-02

Page 41

AREA 51 Operator’s MANUAL @& CHAPTER 4 — Parts ILLUSTRATIONS

Area 51 EC20X32 PCB Assembly Parts List

Desig- Desig-

nator _ DescriptionPart No.nator _ DescriptionPartNo.
2BSocket, 68 Pin, PGA for 68PLCC IC179237-068GND1, 2Test Point179051-001
3H, 3K, 3M, 3PJXBUS96Conn, 96 Ckt, Rept, Pressfit, Short_179368-0196
Socket, 32 Pin, .600, Dbl Wipe179356-0632PWRConn, 9 Ckt, Hdr, .156 Ctr, Rt, Key 3. 179165-009
5DSocket, 24 Pin, .600 Dbl Wipe179356-0624

1D, 1E, 1H, 1K, 1M, 12, 2D RI-R3__Resistor, Chip, 2.2 KQ, +5%, 1/8 W, 1206 112006-0222

IC, 74F245, $020.3,137591-0001R4Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

RS Resistor, Chip, 220 Q, +5%, 1/8 W, 1206 112006-0221

3cIC, 74F04, $014.15137437-0001RO-R8_—_—Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

4/5A IC, CPU, 68EC020, 25 MHz, 100PQFP 137691-025

4D/EIC, DS1232137762-001R10Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103
5DIC, RAM, 48T02, Battery W/Clock — 137540-150RUResistor, Chip, 22 Q, +5%, 1/8 W, 1206 112006-0220

R12-R14__ Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103

SF,5J,5L,5N IC, SRAM, 32KX8, 20 ns, SOJ28.337670-1020R15, R16__Resistor, Chip, 22 Q, +5%, 1/8 W, 1206 112006-0220
6BIC, 74F74, $014.15137436-0001

RI9 Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 12006-0103

€2-C12, C15-C26R20Resistor, Chip, 10 Q, +5%, 1/8 W, 1206 112006-0100
Capacitor, Chip, .1 pF, 50 V, Cer., 1206 125003-0104R22-R26Resistor, Chip, 22 Q, +5%, 1/8 W, 1206 112006-0220
©27Capacitor, 100 pF, 16 V, Electro., Axial 124008-107R27Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

€28, C29 Capacitor, Chip, .1 pF, 50 V, Cer. 1206 125003-0104

30Capacitor, Chip, .012 pF, 50 V, Cer. 1206 125002-0123R28Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103

R29 Resistor, Chip, 10 Q, +5%, 1/8 W, 1206 112006-0100

C31Capacitor, Chip, .1 pF, 50 V, Cer. 1206 125003-0104R30Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103
C32Capacitor, Chip, .012 pF, 50 V, Cer. 1206 125002-0123R31Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

C33 Capacitor, Chip, .1 pF, 50 V, Cer., 1206 125003-0104

C34Capacitor, Chip, .012 pF, 50 V, Cer., 1206 125002-0123R32Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103

R35 Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102

C35Capacitor, Chip, .1 uF, 50 V, Cer. 1206 125003-0104R36Resistor, Chip, 10 KQ, +5%, 1/8 W, 1206 112006-0103
C36Capacitor, Chip, .012 pF, 90 V, Cer, 1206 125002-0123R37-R39__Resistor, Chip, 1 KQ, +5%, 1/8 W, 1206 112006-0102
CRILED, Grn, MV5453, T1-3/4, 20-MCD,R40-R42Resistor, Chip, 22 Q, 5%, 1/8 W, 1206 12006-0220

Wide 138020-001

x1Crystal, 50.000 MHz, Osc. Module144008-005

4-15

Page 42

Cuarter 4 — Parts ILLUSTRATIONS AREA 51 OPERATOR'S MANUAL

Figure 4-7 Area 51 Gun PCB Assembly A051987-01 |

Page 43

AREA 51 OPERATOR'S MANUAL CHAPTER 4 — PARTS ILLUSTRATIONS

Area 51 Gun PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
c2CAP, .01 pF, 50V, +10%, CER122015-10311,13INDUCTOR, FERRITE BEAD, N12N__141003-005
c1,c3CAP, .1 pF, SOV, +80%-20%, CER122002-10412INDUCTOR, 5.6 pH141016-562
C5CAP, 1000 PF, 100V, +5%, CER122016-102
C4,C6,C7_ CAP, 22 pF, 16V, £10%, TANTALUM,R2RES, 100KQ, +5%, 1/8W110027-104
RADIAL127003-226RIRES, 150KQ, +5%, 1/8W110027-154
R4,R7RES, 1KQ, +5%, 1/8W110027-102
ylCONN, 4 CKT, HDR, .100 CTR,RSRES, 200KQ, +5%, 1/8W110027-204
RT-ANGLE179165-004R3RES, 24KQ, +5%, 1/8W110027-243,
R8RES, 47Q, +5%, 1/8W110027-470
CRI-CR3_DIODE, 1N914131052-001RORES, 47KQ, +5%, 1/8W110027-473
UlIC, LM311137687-001QiTRANS, 2N3904133041-001
Q2TRANS, MRD300, TO18133038-001

4-17

Page 44

Cuapren 4 — Parts ELLUsTRATIONS @ Anta 51 OPERaTor’s MANUAL

I i

Page 45

CHAPTER 5

Schematic Diagrams

INTRODUCTION

HIS CHAPTER contains schematic

diagrams for various parts of the Area

51” game, including the gun assem-

bly. In addition, this chapter in-

cludes wiring diagrams for the

entire game and the coin

door. The PCB assembly

drawings are illustrated in

Chapter 4, Parts Illustrations.

Page 46

5-2 Cuarrer 5 — SCHEMATIC DIAGRAMS @ AREA 51 OPERATOR'S MANUAL

comp srwe

oxo

vioe0 o1sPay

FuuoRescent LIGHT acewn | —4

054644-01 Rev. A i

Figure 5-1 Area 51 Game Wiring Diagram MAIN PCB

AT powER suPpty (COJAG-REV2)

+ “ cont _t a —_ com R 4 - “. ono cena

com oo0R No

comm couNTER sw

Onsore si.

NE

eur

Page 47

5-3 Figure 5-1 Area 51 Game Wiring Diagram, Continued 054644-01 Rev. A yo un Pca To uN rca est si a ah rRicoeR TRIGGER No

swe seen an ono unsPao uN Pao

RELOADO

Taieo key SeRseNo sv exo ee eno suns ra GUNSPAT RELOAD rats ey ScRSENI a sv OM exo staat w own Lert aucit suTront Burrone aurron3 aurToNs (CAGE AUDIO) PLAYER 2 AREA 51 OPERATOR'S MANUAL @% CHAPTER 5 — SCHEMATIC DIAGRAMS

Page 48

CHAPTER 5 — SCHEMATIC DIAGRAMS AREA 51 OPERATOR'S MANUAL

aiaaanwopowenY
(6x0) oath0 6x0(ono) JARNA-Aao fana
(HO) oa?a)GRD) AHABom 2 ONDTare Saar Sf mao Le
(5H) aie 3ayCe5¥) HACv3 ne GNDmw Sa Sano 1K
(5) Ok(59) AADsk oe oYj
C50) akaovC54) AHAsvCS aies 865g come
(era¥) aan-6dawce12) ama Fsecoms Doggie a4 comes
KEY OANA?cameroncone ef ge360 a302 7 Sonne
(CENTRE) JANMA-B= CONT(CONTR) JAMMA-S‘cnr?com ettey1k 8 comma

CC-L0CKL) HA (C-19KR) SMH

(SPKRR) JAMMA-10——w SPKROLB(SPKR-R) JAMMA®LSPKR-LBC65 cas i c16 1.c20
(SPKR¢L) JAMMAZLT0 SPKRERB(SPKR-L) JAMMA-MSPKR-RBop7*|
(RED) QAMMA-12,—w RED(GREEN) JAMMA-N-GREEN= ee * °
(BLUE) AMAL?BLUE(SYNC) JARHAPcovmstne
(vio GND) damnvioeny(SERVICED vaNMA-stavice
(SELETEST) OAMWATS OOa SeLFTEST(IUT)GAMNA-S.muv
(COIN) 2AMA- 6—S coin(cone) JANHA-TcoinetL
(STARTL) DAMA?STATstant) sawedstarem trae tase tar Las
(UPLA) YAKWA28counCUPRA) GAMveewo Sar a0 S470 ar
COMMA) 3AMHK- 19om(oownek) IANone
(LesTiA) anima: 20in(LETRA) JaNMA-XreSTE a4{|Lay FE
(RIGHTLA) amma 21maIGaTRA) amyaresewicer © gePak RD See
BUTTON) aMea: 22FIRE.CRBUTTONI) JAMA?rineeSERICES ef}BS st
(BUTTON?) DAMRA- 23ACTAL——(RBUTTON2) AMHA-AAAcrepe aeeDETone ot ES
(RuTTONS) AMMA: 24Acre(RBUTTONS) AMRA: 8Bacta
CLEFTUB) QAMHA-25CLEFTRB) UAMMASCEsenvice?SELFTEST & +pgtg tly BTSTIS
(RIGaTLR) oAMMA- 26acter¢RIGHTRB) JAMMA-00cree
(hO) DAMKA-27exo{ORD} UaMMA- Eeonoce Leis leu Less | as ig
{GND} DANA 28ovo(ND) samin-rr“a 6xPeatGhats

Sh seurrest

as is SPaRLB | rr

Acressees 5 Hea8Latowas0 | as
acra3.oe1K200= 470470470

corn} 20

ACTASYNCAf£a HSYNC.OUT
{2CONTS we6i
Lsae4 15Fzo|:
avsconean?caeosei
wseasbe
‘STATSLim |Te£06
Seanceisiee vane ur

cvs

4best30ciacai
esSPKRRB~ a | oor n= au1000PF ‘1000PF1000PF

oxo ta u suns of sa a7

4ACTCA2 BEAD
3ACTBSLi

ae ae nterr

2ACTASensBEAD AHAE+5¥1 +5v2 +5¥3, +5V4iH
uFIREAhs0“SYNCDEW_OMLY‘ )DCV_ONLY DEW ONLY |" DEW. ONLY’i
10RTaeBea ——® L0.LEFTHSYNC.OUT1+ 8 Od ° a ==
owIVERTe GRO OTPGND TROND’ TP cwD|
7aevoncre2|
4eno|hoe

ae oe

.012cu5
1LL| pa» oxoOno ey yy1;
bepoean|

§ nee :

J cracrtanj
ttt2 Soo:te

of mer

+ Fusa06ikA Bhss06 |
CCL yy ALO |CoAyy, R03 fT|peneat2
,5|

1s

oneanoaxe—

a 2g

nean:|
ee conre$s consono
*ysa06soe Mygaiaejes

ono ad

Figure 5-2 Cojag Board Schematic Diagram Sheet 2 of 10

(053537-XX Rev. D

Page 49

AREA 51 OPERATOR'S MANUAL @& CHAPTER 5 — SCHEMATIC DIAGRAMS

aor eos

eos

eve Revi e00

GREEN? GREENS GREENS ‘GREENA GREENS Greene GREEN GREENO neTeas, | | | Le acnceno one |e aoreen

Ln sorcene + asreena a aGREENA ae BGREENS

  • a BGREENG 7 a BGREENT

aver sues auues. atuce aiuea Blue Blues alueo

Le ssiueo exo Le antuen

——e antuee a 8BLUES —e waLuee a aLues a paLuce Bae

+8

Se :

ania = 470

Say 190Low RED

oncor aoe eos cod oa oxo2 v1 os ene

anagos7TMELESR

| aoa cs 10, 894 on ae _ 2 RED

21006

evo

vroewo

ery

“a oe ye

le)2nag0apo SMELLS

+

cas . - eReEN

= aro%e

‘eNzRD = ——— NFER 1

ovo

= viocNo

Mee oy

[oyawe

po) tee oweLisa

mui aoe aaty Fae | 10, rior 20, R07

SUUETERG

oRceNe GREEN GREEN?

BREEN BGREENO aa.ue7 BaLUES aLUES aiuee aaLues aa.vee saiuei Baiueo

GREEN GREENS GREENS

RODET2B 16v8 SH 154s ay [eRaDETA— oo} teva se 15hs ‘BLUEZERO ay

oY a) BANTER

<= REOTERO

JAMMA, Vcc Check, & Video DACs SOCKET=NO

Figure 5-2 CoJag Board Schematic Diagram, Continued

Sheet 2 of 10

053537-XX Rev. D

Page 50

CHAPTER 5 — SCHEMATIC D1aGRAMS & AREA 51 OPERATOR’s MANUAL

i a rr or or oe = R299. RIS. R298. RIS |. REIT. RIZ R92. RF 470 © 470 2 470 470 470 | 470 = 470 470 ATE? wg ners) ge t i ACTA? ACTAL FiRe2

FIREY stare sTRT} 1 ep ay 22 001

L crak. cae L cza. ca? c1ae.t c26 | cri? ca vat Ppa papa papa 1

ee HD

Se 22k

ree | 29. REO. RIO |. RTO RBI RIS R96 - 15 470 = 470 3 470 470 = 470 3 470 © 470 > 470 t acres acTs3 ACTAS ACTAS

FuREs

FIRES stata STRT3 a 1 . —_ c47 c36 cae 36 cag 037 1 54 ca (ses7 Pata papa Pea pap epee eee

Pe oe ae or oe ae Srey)

Se oom

a9. R298. R10 470 © 470 2 470 = R293. RB 470 = 470 R296. RL

Ue? a9 0 UPL ee DN2 * DRL» ure

ur at2

aT ay [22 __t018

cane. c22 teri c23t cizol c2a O12-y 0127 012.012.0127 0127 1 tf GND ae

+5

ura uP3 Da

ura FS ava RT3 “cay 52 1 co cs e391 cso 38 "18267 Saye pa pasa pa 1 = 083 a or er or a Sar Soe

JAMMA Registers & Decode

Figure 5-2 CojJag Board Schematic Diagram, Continued

Sheet 3 of 10

(053537-XX Rev. D

Page 51

AREA 51 OPERATOR'S MANUAL & CHAPTER 5 — SCHEMATIC DIAGRAMS

£0r15:01

avupon

STAT FAL COrNRA 4B 4h 10 | 35 OrNRS ee - Lisa | cotnre —-6. 28 ar

Figure 5-2 Cojag Board Schematic Diagram, Continued Sheet 3 of 10

053537-XX Rev. D

Page 52

CHAPTER 5 — SCHEMATIC DIAGRAMS @ AREA 51 OPERATOR'S MANUAL |

ne

t Les

l eV i

a aed

su

}

Figure 5-3 Gun Board Schematic Diagram 51987-XX Rev. B

Page 53

AREA 51 OPERATOR'S MANUAL @& CHAPTER 5 — SCHEMATIC DIAGRAMS

i)

i)

' NC ;

Right Coin Switch Ne '

Y NOSN¢ BK ' SW GND 1 Left Coin Switch ' RIGHT COIN SW | 2

LEFTCOINSW| 3

' :

! 7 1

8 i)

GND] 7

+5VAC | 8 CHASSIS GND | 9

i)

i BU '

GN 1

>| z ' al

i

i

'

'

Figure 5-4 Coin Door Wiring Diagram 047366-01 Rev. A

Page 54

Cnapren 5 — SCHEMATIC DIAGRAMS @ ARFA 51 Operator's Manual,

NOTES

Page 55

Peale alee eee eel eel el

If the products described in this manual fail to conform to this warranty, le liability shall be, at its option, to repair, replace, or credit Buy- Seller's so! er’s account for such products which are returned to Seller during said warranty period, provided:

  • Se sai

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

ler is promptly notified in writing upon discovery by Buyer that id products are defective; Such products are returned prepaid to Seller's plant; and Se ler’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or im; In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

elelelelelel leet eleleleleletrel celal felfelel el el felfetrel pel fel resettled fel

‘The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. proper testing.

Page 56

TIME WARNER

INTERACTIVE

675 Sycamore Drive Milpitas, CA 95035 U.S.A. (Formerly known as Atari Games Corporation)