CATHODE RAY TOMES

Jungle Hunt to Elevation Action Conversion Kit

Jungle Hunt to Elevator Action Conversion (Taito America Corporation, 1983) · Kit Manual · 18 pages · 16 sections · original scan

Page 1

TAITO AMERICA CORPORATION

CONVERSION KIT |

JUNGLE HUNT

Page 2

WARNING

The parts contained in this Same conver-

The parts contained in this Same conver sion kit must be installed in accordance with the instructions Contained in this Ser vice Manual. Failure to follow these in structions in every detail could result in the creation of illegal interference to radio and TV reception Taito America Corporation has verified that, when this Conversion kit is installed without deviation from these instructions, the equipment will then comply with the requirements of Part 15 of FCC Rules for a Class A computing device. The man ufacturer will not be responsible for in complete or improper conversions After such installation in accordance with the instructions, the enclosed NOTICE AFTER CONVERSION should be applied to the back of the game cabinet So as to cover up any previous notice regarding FCC Rules

with the instructions Contained in this Service Manual. Failure to follow these in-

and TV reception.

a Class A computing device. The manufacturer will not be responsible for incomplete or improper conversions.

FCC Rules.

Page 3

TABLE OF CONTENTS

CONVERSION INSTRUCTIONS ... 2.2... 2 ee ee eee eee 1,2

REPLACEMENT PARTS LIST ... 1... 2. ee eee eet ees 3,4

DOOR ASSEMBLY .... 2... ee ee et 5

ELEVATOR ACTION ROMS .... 1... ee eee eee eee eee 6

SECURITY BOARD CONNECTION ... 2... 2.2.22. 02+ ee eeee 7

SECURITY BOARD ASSEMBLY ...... ee ee 8

SJC3 PC SYSTEM BOARD SET... 1... 2. eee ee ee ee 9

GROUND PLATE ASSEMBLY MOUNTING .........-.2055 10

GROUND PLATE ASSEMBLY DETAIL .........-0 252s 11

CABINET INTERIOR .. 11. 2. ee ee ee ee et 12 MONITOR GROUNDING ......... occ ev eeees 13

RFI SHIELD INSTALLATION . 1... 1. ee ee es 14

CONTROL PANEL .. 1... 1. eee eee ee ee 15

Page 4

This manual will guide you in the conversion of your JUNGLE KING/JUNGLE HUNT™ upright game to ELEVATOR ACTION™. We urge you to read through the instructions and study the drawings before beginning the conversion. Perform the instruction steps in the order presented. |. Check the parts supplied in this kit against the parts list included in this manual.

  • Remove JUNGLE KING/JUNGLE HUNT Control Panel. a. Release the latch at each end of the control panel (access through coin door opening). b, Tilt the panel outward from the top and disconnect the cable connector to the right.
  • Remove JUNGLE KING/JUNGLE HUNT Marquee. a. Remove the three (3) allen screws and ining bracket. The marquee will slide out of the guides. b. Remove and save the two (2) plastic “U" channel guides from the marquee. These will be used later. 4, Remove JUNGLE KING/JUNGLE HUNT Coverglass. a. Loosen (but do not remove) three (3) screws holding the coverglass front bracket. b. Remove and save the rear coverglass retaining bracket and three (3) screws. Slide the coverglass out.
  • Remove PC Board Assembly. a. Disconnect the PC Board Harness connectors “G” and “H” at the right side and “T” at the left side of the beard set. b. Rotate the “L” bracket board retainer 90 degrees counter- clockwise and slide the boardset out from the left.
  • Remove Filter Board. a. Disconnect all cables from the filter board. See FIG- URE 1. b. Remove and discard the old filter board.
  • Remove Board Mounts. a. Remove two (2) PC Board Stops (small “L” brackets). See FIGURE 1. b. Remove and save the PC Board Harness. c. Remove and discard the two (2) PC Board Mounting Brackets.
  • Remove JUNGLE KING/JUNGLE HUNT ROMS. a. Separate the PC Boards as shown in FIGURE 2. b. Remove the ROM Board from the PC board set. c. Remove any EPROMS located in the following sockets: ROM Board sockets 1C01 to ICs CPU Board sockets 1C52 to IC55 ICb4 to IC69 GAME Board sockets 1C70 to 1C73 11. Install new ELEVATOR ACTION ROMS.
CAUTION: EACH IC MUST BE INSTALLED WITH ITS NOTCHED END ORIENTED AS SHOWN IN THE APPRO- PRIATE FIGURE. Install the new EPROMS marked “EA09” through “EA27~. REFER TO FIGURE 2 FOR LOCAT- ING ROMS ON THE BOARDS. ROM Board ICs — EA20 through EA27 CPU Board ICs — EA12 through EA19 GAME Board ICs — EA0S through EA10 Install the Security Board. a. Remount the ROM Board onto the GAME Board. b. Remove the Z80 IC from socket IC39 of the CPU Board and install it in location 12 of the Security Board. See FIGURE 3. c. Connect the flat ribbon cable of the Security Board to socket 1C39 of the CPU Board. See FIGURE 3. d. Remove the two (2) plastic board standoffs indicated in FIGURE 4. e. Reassemble the VIDEO and CPU Boards on the remaining beard standoffs. See FIGURE 4. f. Snap the adhesive-backed board mounts to the Security Board as shown in FIGURE 4. g. Assemble the plastic board spacers and snap mounts as shown in FIGURES 4 and 5. h. Peel the paper from the bottom of the adhesive board mounts. i. Snap the Security Board down onto the CPU Board as shown in FIGURE 4. Press the adhesive mounts down on the board. j. Reassemble the GAME and VIDEO boards on their plastic standoffs. Install New Ground Plate Assembly and PC Boards. a. Relocate the lower latch bracket on the back door. In most cases the bracket may be relocated by removing the right-hand screw, rotating the bracket 180 degrees, and installing the screw on the left. The Ground Plate Assembly consists of a ground plate, plastic RF shield, filter board and PC board mounting brackets. b. Positon Ground Plate on back door as shown in FIGURE 6. Center plate between Lower Latch bracket and door hinge, leave 4” between bottom of door and plate. c. Screw brackets to door as shown in FIGURE 6 with wood screws. d. Screw filter board to door as shown in FIGURE 6 using screws from old filter board. e. Screw “L” brackets and spacer to door See FIGURE
Page 5

f. Slide the board set into the mounting brackets with the “G" and “H” connectors to the right and the $JC3 Board next to the ground plate. Set the board stops against the boards and tighten the screws. g. Reconnect the PC Board Harness to the “G", “H", and “T” connectors on the board set. Reconnect the five (5) connectors to the lower portion of the Filter Board. Dress the harness as shown in FIGURE 7 and install three (3) cable clamps. h. Reconnect the six (6) Main Harness connectors to the upper portion of the Filter Board. See FIGURE

  • Note: Use holes in ground plate as a template.
  • Install Ground Braids. a. Connect the 16 inch ground braid to the Ground Plate with a screw in the hole near the lower right corner. Connect the other end of the ground braid to the power supply circuit board mounting screw. Scrape any green solder mask from the hole pad on the power supply circuit board before assembly. Tie wrap the ground braid to the Main Harness to prevent short circuits to the fuses. See FIGURE 8. b. Connect the 28 inch ground braid from the power supply P€ board mounting screw to a convenient chassis screw on the monitor. Scrape any green solder mask from the mounting hole pad before assembly. See FIGURE 9. c. Connect the 9 inch ground braid from the power cord filter box to the power supply PC board mounting screw. Scrape any green solder mask from the mounting hole pad before assembly. See FIGURE 9. d. Connect the 5 inch ground braid from the lower rear door lock mounting screw to the upper left corner of the ground plate. See FIGURE 6.
  • Install ELEVATOR ACTION Coverglass. a. Clean the coverglass with a non-abrasive cleaner. b. Install the covergiass from the rear of the cabinet. c. Tighten the three (3) screws on the front coverglass bracket. d. Install the coverglass retaining bracket at the rear with three (3) screws. 14, Install ELEVATOR ACTION Control Panel. a. Remove cable assembly from control panel being careful not to break tabs off of any leaf switches. b. Remove the joystick, buttons and wood braces from the control panel. c. Remove the (4) leaf switches and the switch plate from the joystick. Install the switches on the new 4-way switch plate and replace the switch plate back on the joystick. 17.

18.

19. d. Install the joystick, (with new actuator), buttons, (including the two new ones) and the wood braces on the ELEVATOR ACTION control panel metal. See FIG- URE 11, e. Take the violet wire in pin 9 out and insert it into pin 7 of the control panel cable connector. Insert the pin end of the green fire cable into the pin 9 hole on the control panel cable connector. f. Reconnect the control panel cable to its original ‘state except connect the green wires to the inside fire buttons. See FIGURE 11. g. Connect the black ground wire to the inside fire buttons and splice the stripped end into one of the existing black wires. h. Reconnect the control panel to the main harness and mount the pane! on the cabinet. Be sure no wires are pinched by the latches. Install ELEVATOR ACTION Marquee. a. Attach the two (2) plastic “U" channel pieces to the sides of the new marquee and slide it up into the cabinet. b. Attach the marquee bracket with three (3) allen screws. Adjust Game Settings. a. Consult the ELEVATOR ACTION Manual and adjust the DIP switches as desired. b. Turn the game ON and play a “2-PLAYER” game. Adjust the volume controls as desired. Install Plastic RFI Shield. a. Carefully fit the shield over the board set. Check that the PC Board Harness does not push against the shield and that the wires on the lower portion of the filter board do not protrude under or push against the shield. Insure that the ground braid at the lower right lies flat between the shield and ground plate. See FIGURE 10. b. Secure the shield with eleven (11) screws & washers. The RFI Shield must be held FIRMLY against the Ground Plate to prevent radio frequency noise emission. NOTE: The volume controls are accessible from a hole in the underside of the shield. c. Close and lock the rear service door and the coin door. Attach FCC Compliance Label. Affix the new self-adhesive FCC Compliance label OVER the original label on the rear of the cabinet. Attach the FBI Warning label. Affix the self-adhesive FBI label on the outside of the rear door near the top in the center. The conversion is complete.

Page 6

JUNGLE KING/JUNGLE HUNT TO ELEVATOR ACTION CONVERSION PARTS LIST

tHeotinetonene ACCESSORY & HARDWARE PACK *#8# #8 tb HH PART NUMBER DESCRIPTION QUANTITY

63-00144-001SCREW INSULATOR2
63-00145-001PCB SUPPORT2
63-00146-001PCB SUPPORT, ADHESIVE2
63-00147-001PLASTIC SPACER2
09-00260-001BRAIDED GND CABLE 9”1
09-00260-002BRAIDED GND CABLE 16”1
09-00260-003BRAIDED GND CABLE 28”1
09-00260-004BRAIDED GND CABLE 5”1
§1-01012-001#6 X 1" SCREW2
51-00005-001#8 X 11/16 SCREW11
51-01012-006#6 X 1/2” SCREW4
51-01022-0156X 11/2 HH SCREW2
55-01004-001#10 x 1/2" WASHERli
59-00016-002SPACER2

Jon na dndrnianenneaae MANUAL PACK Sob nnn Hi iiaacioniner

79-00075-001SWITCH SETTING CARD1
72-00042-001GAME MANUAL EA1
72-10007-001CONVERSION MANUAL JK/JH - EA1
79-00070-001GENERIC FCC COMP. LABEL1
79-00074-001FBI WARNING LABEL1
Page 7

JX np nae EDIE CONVERSION KIT a i ibenbiciinaiirinies

16-00032-100 EPROM SET EA SJC3

*07-00261-001 BRACKET ASSY *07-00262-001 BRACKET ASSY

*61-00300-001 GROUND PLATE *63-00140-001 PLASTIC RFI SHIELD

*08-00120-001 FILTER BOARD 47-00016-008 E.A. COVERGLASS

47-00012-017 MARQUEE, E.A.

08-00116-003 SJC3 SECURITY BOARD E.A.

Jonnie CONTROL PANEL PACK tt#t tite trie eee

07-00281-002 CONTROL PANEL ELEVATOR ACTION

09-00287-003 BLACK WIRE

09-00278-002 GREEN WIRE 63-00024-001 PUSH BUTTON

29-00020-001 PUSH BUTTON SUPPORT

54-07001-008 NUT 63-00028-002 PLATE

63-00030-001 ACTUATOR Pee eee eee

PPNNNBe Re

Page 8

JUNGLE KING /JUNGLE HUNT

DOOR ASSEMBLY

FILTER BOARD

MOUNTING BRACKET BOARD STOP

GROUND PLATE {NOT ON ALL GAMES]

Page 9

ELEVATOR ACTION ROMS

VIDEO BOARD

| E

aS ( =) / i S| fl fC 1

f OO ff WC . a t CPu-BOARD | va t if !

t i

Page 10

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 11

SECURITY BOARD ASSEMBLY

SCREW INSULATOR

-00144alee detail REMOVE ORIGINAL PLASTIC BOARD

STANDOFFS AT THESE 2 LOCATIONS

SCREW AND INSTALL NEW PLASTIC PARTS

#6-1V0 AND SCREWS. 51-01022 -015 “ oO PLASTIC SPACER b 63-00147-001 Z

4g oF

PCB SUPPORT Z

63-00145-001 Z

° ° / Z

S

SECURITY BOARD,

PCB SUPPORT 63-00146-001

Page 12

“SM3YOS ONV SLYVd O1LSVId MAN TIVLSNI ONV SNOILVDO1 @ ASSHL LY S44OQNVILS GuvOS OILSV1d IWNIDIHO 3AOWSY —f. agyuvod aWyD ——- duyvog O3dlA

oe —~———— duvOd Nndod —<——aguvod ALIHNDAS

ad as aqavd Nogaly

13S GUVOd WALSAS Od €9Fs g SYNOD

Page 13

GROUND PLATE ASSEMBLY MOUNTING

FILTER BOARD IS) @ BA DO | i) L Q 8 2 a

| 07-00261-001 1) oy | nL! BRACKET & SPACER

| | !

6! I BI ror 2-001 © |

| ® i) 8 el fe |

=] METAL GROUND PLATE eal LOWER LATCH BRACKET BR

Page 14

GROUND PLATE ASSEMBLY DETAIL

2, X00" GROUND BRAID x TO DOOR LATCH

PC BOARD HARNESS |

CABLE CLAMP

\ le) Z1el DOOR HINGE -\ © —t = == [PC BOARD STOP | © @ 8 i - ae | PC BOARD MOUNTING | @oraccer PO

L _ -

G PLATE 16” GROUND BRAID METAL GROUND TO POWER SUPPLY

Page 15

CABINET INTERIOR

5! GROUND-——TTT | !

BRAID Wy

FILTER BOARD

16” GROUT BRAID

NOTE: GROUND PLATE ASSEMBLY SHOWN WITHOUT RFI SHIELD TIE WRAP 9” GROUND BRAID
Page 16

16" BRAID TO GROUND PLATE MONITOR GROUNDING

<~—_—_———._ 28" BRAID

9” BRAID

Page 17

RFI SHIELD INSTALLATION

GROUND BRAID TO POWER SUPPLY MUST LIE FLAT

WASHER & SCREW A ~e

Page 18

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.