CATHODE RAY TOMES

StarBlade Operators Manual

Starblade (ST2, World) (Namco, 1991) · Manual · 32 pages · 12 sections · original scan

Page 1

Namco-America, Inc.

Operators Manual

Page 2

STARBLADE™ Operators Manual

SCAN BY DARTH NUNO VISIT MY STARBLADE PAGE AT WWW.DRAGONSLAIRFANS.COM

Page 3

10.

11. CONTENTS

SPECIFICATIONS ..........2,:-:-0--0-0------s-sssssssesdesscnessensesensnessenssscnsrseiquessssecusbonsgesinensseneenenensesenorsean tenes 1

PRECAUTIONS 2-1 Installation Precautions 2-2 Handling Precautions ..

INSPECTION ......

INSTALLATION 4-1 Seat Base ... 4-2 Monitor Cabinet 4-3 Seat Assembly... 4-4 Level Adjustments 4-5 Power and Final Setup

ADJUSTMENTS 5-1 Power Switch . 5-2 Adjustment Switches on the Service Panel 5-3 Test Mode 5-3-1 Main Test Menu. 5-3-2 Game/Coin/Option Screen . 5-3-3 Switch Test Screen.. 5-3-4 Sound Test Screen 5-3-5 Effect Test Screen 5-3-6 Monitor Test Screen 5-3-7 Object Test Screen 5-3-8 ADS Screen 5-4 DIP Switches .... 5-5 Monitor Adjustment. 5-6 Gun Adjustment .............cceseeeeseees HOW TO PLAY ..occscccccscccsssessecsessssssnessssssssnseessscsesessecnesasenccnssnessesacenssnssavecascossneesecueenennenscesnts 12

MAINTENANCE 7-1 Marquee and Fluorescent Lamp Replacement 7-2 Gun Assembly Replacement 7-3 Hemispherical Mirror Replacement and Cleaning 7-4 Vibration Assembly Replacement 7-5 Game PC Board Removal ....... 7-6 Monitor Board Access 7-7 Monitor Tube Removal .. 7-8 Strobe Lamp Replacement TROUBLESHOOTING .........cscsssececcssscssecoessnsseessesnesscensnssssesssesenennecacsncanernceseensesseessasausnegnastesenense 16

PARTS LIST............

GAME WIRING HARNESS DIAGRAM .....

LIST OF ILLUSTRATIONS (see over)

Page 4

11. CONTENTS (cont.)

LIST OF ILLUSTRATIONS

BAA SUE VIG WTON GING rcs c00n scoop ssegaatasesnes ree eee ean a SPIN xfeaah aapetooabicoRestscaranns 3 5-1 Service Panel.

5-2 Gun Assembly.

5-3 Test Menu Screen.. a8

BeAie Games OPO SCHON bess ers es ceecesveeraveraccrmmencscevarteeercscrtan terremnetevey aide enna sean 5-5 Switch Test Screen po MCUs ors ob sede ca cpacovohiattns ts HRPESIVGAN gray nes Neo ns tra 5-6 Sound Test Screen

5-7 Effect Test Screen .

5-8 Monitor Test Screen 9

5-9 Object Test Screen 10

5-10 ADS Menu Screen . 10

5-11 Monitor Remote Adjustment Board

5-12 Gur Aiming Screens oon. .ecececscesssseesesseesessesssreessssssasecsessessessesuesvesseanessaseesseaeesesseesseseesves a

7-1 Gun Assembly Replacement «...............ssecssecsesssessessesssessneesscssscsuecssecsuccssensessutessussnesseessse 13

7-2 Vibration Assembly Replacement ...................cs-essssssssesseesvessessesesessseeseesseeseeseveesneensessseseees 14

9-1 Vibration Assembly ..................... ey | 9-2 Gun Assembly (exploded view) ...... 22

9-3 Coin Assembly (exploded view) .................... 24

x-x Game Wiring Harness Diagram ...............200.+ 26-27

Page 5

STARBLADE™

  • SPECIFICATIONS

POWER SUPPLY:

POWER CONSUMPTION:

MONITOR:

DIMENSIONS (assembled):

CRATED DIMENSIONS:

Mirror Cabinet Seat Assembly Monitor Cabinet

SHIPPING WEIGHTS:

ACCESSORIES:

  • PRECAUTIONS 2-1 Installation Precautions UL Listed PC XT Type Switching Power Supply Total 240 W One standard 25" Color Monitor with auto-degauss and remote adjustment board

Width Depth Height

43.5"Ths"81"
49"40"79.5"
41"61"51.5"
36"32"39"

Mirror Cabinet Seat Monitor Cabinet 478 lbs. 236 Ibs. 172 lbs. Keys: Coin Box . Coin Door Rear Door Security Wrench 3/4" box end wrench... Instruction Manual ... Tnstruction! Gard Wire avesssesseseontocevnnvesstessrnesse

Note: Specifications may change without prior notice. Modification and/or alteration of the STARBLADE™ game with kits or parts not supplied by NAMCO may void the warranty.

This game is designed for indoor use only. It should not be installed outdoors or

under the following conditions: a. In areas directly exposed to sunlight, high humidity, direct water contact, dust,

high heat or extreme cold. b. In locations that would present an obstacle in case of emergency, i.e. near fire

equipment or emergency exits. c. Onan unstable surface or floor subject to other vibration.

Page 6

2-2 Handling Precautions a. Do not subject game to physical shock when transporting or moving it. b. The cabinet should be grounded with a securely connected ground line. c. The monitor includes areas of high-voltage. Care should be taken at all times to avoid electrical shock whenever inspecting or adjusting the game. d. When unplugging the game from an electrical outlet, always grasp the plug, not the cord. Power should always be turned off before replacing any parts. DO NOT attempt to repair the Printed Circuit Board (PCB) on site. It contains sensitive integrated circuit chips that could easily be damaged by even the small internal voltage of a multi-meter. Always return the PCB to your distributor for any repairs. g. Always return the leg levelers to the extreme “up” position before moving the game. h. Adjustment is required whenever the game PC board, ROM, gun assembly or volume control is changed. (ref. sec. 5—6, Gun Adjustment) i. Exercise caution to prevent scratching the hemispherical mirror located within

the cabinet.

  • INSPECTION The STARBLADE™ Game should be carefully inspected upon receipt to insure that it is complete and was delivered in good condition by doing the following: 1, Examine the cabinet exterior for dents, cracks, or broken parts.
  • Inspect the monitor cabinet for dents, cracks, or broken parts.
  • Inspect the seat assembly for punctures, cracks, or other damage.
  • Open the rear doors and; a. Verify that all plug-in connectors (on the cabinet harness) are firmly plugged in. DO NOT force connectors together. The connectors are labeled to assure the proper orientation. A reversed edge connector can damage a PCB and will void your warranty. b. Inspect the power cord to insure that there are no cuts or dents in the

insulation. c. Inspect the power supply connectors. d. Inspect all other major sub-assemblies, such as the hemispherical mirror, strobe lights, PCBs, etc. Make sure that they are mounted securely and that

all ground wires are firmly connected.

  • Read section 4 and check for missing parts or fasteners.
Page 7
  • INSTALLATION Allow yourself about 2 to 3 hours for proper assembly of STARBLADE™. A minimum of 3 people are needed to install the monitor cabinet (step 4-2 takes about 30-45 minutes).

4-1 MONITOR CABINET

SEAT ASSEMBLY

STRUT COVERS

ISOLATION COVERS: (3-under seat assembly) SEAT BASE |

  • LEVELING/ HEIGHT ADJUSTERS oy a

Illustration 4-1, 3/4 VIEW Seat Base To install the seat base, locate the wire harness coming out of the front floor of the mirror cabinet and line up the holes on the seat base brackets with the holes in the

mirror cabinet. Carefully feed the wire harness through the hole provided in the seat base, then screw in and tighten the base using the four (4) black 5/16" x 1 1/2" hex head bolts and washers provided (from the coin box accessories kit).

Monitor Cabinet

CAUTION - THE MONITOR CABINET IS VERY HEAVY AND REQUIRES A MINIMUM OF THREE (3) PEOPLE TO SAFELY INSTALL. Before installing the monitor cabinet, insure that the mounting bracket and monitor openings are clear of any obstructions. Also insure that the seat base has been properly installed and secured. Failure to install the seat base first can cause the mirror cabinet to be unbalanced and fall. Remove the top panel of the monitor cabinet by removing the four (4) phillips head screws retaining the 32" x 27" panel. Carefully lift the monitor cabinet and lower it onto the support bracket on the top of
Page 8

the monitor opening of the mirror cabinet. Using the four (4) 5/16" x 1 1/2" black hex head bolts and washers provided in the coin box accessories kit, secure the monitor cabinet in place from the inside of the mirror cabinet. The 66" metal struts are mounted with the sloted hole attached to the seat base. Slide one strut cover (from the coin box accessories kit) and one side of the plastic yellow marquee frame over each strut. Be sure that the marquee will be facing away from the game once installed. Both struts should be secured to the side of the strut mount furthest away from the mirror cabinet. Attach the two struts to the seat base and monitor cabinet mounts using the four (4) 3/8" x 1" hex head bolts, flat washers, lock washers and nuts provided in the coin box accessories kit. Secure the yellow marquee frame with the seven (7) 10/24 x 1" tamperproof machine screws to the monitor cabinet. Attach the plastic grey strut covers with eight (8) #10 x 1/2" tamperproof sheet metal screws to the seat base. From the top of the game, connect the monitor harness and resecure

the top panel of the monitor cabinet.

Seat Assembly To install the seat assembly, place the three (3) grey plastic isolation mount covers (from the coin box accessories kit) onto the isolation mounts. Locate and extend the seat assembly wire harness from the access opening on the bottom of the seat assembly. Carefully bring the seat assembly into position directly through the support struts. Use caution not to damage the threads of the isolation mounts when installing the seat assembly. Thread the harness through the hole in the seat base and set the seat assembly on the isolation mounts. Using the nuts, lock washers and the 3/4" box wrench provided, secure the seat assembly to the isolation mounts. There are three (3) yellow end caps that are secured by two (2) black phillips head screws each to cover the open ends. Connect the two plugs of the seat assembly harness underneath the seat base and secure the harness with the mounts provided. Neatly pack the excess harness above the front wheel mount on the seat base.

Level Adjustments Each STARBLADE™ game has six (6) leveling/height adjusters — one on each corner of the mirror cabinet and two on the back of the seat assembly. It is important to lower all leg levelers to provide a stable, shock absorbing cabinet.

Power and Final Setup Plug the power cord into the game and the AC outlet. If the game doesn't come on right away, press the power switch on the lower left side of the cabinet. If the game still does not operate, call your distributor or NAMCO Customer Service. Adjust the game/gun controls (see section 5-6) to insure proper operation. Change the game settings for your location (see section 5-3-2). Turn off the test switch and play the

game to confirm your settings.

Page 9
  • ADJUSTMENTS 5-1 Power Switch When installation is complete, connect the power cord to an AC outlet and turn the power on. The power switch is located on the lower left side of the mirror cabinet.

5-2 Adjustment Switches Open the upper coin door to gain access to the service panel.

VOLUME 1—}-> a |<} VOLUME 2 HIGH BACK

oN CREDIT SWiTCH—}-> < TEST SWITCH OFF

coin couNTeR |» | [123456

Illustration 5-1, SERVICE PANEL

Test switch Toggle this switch to “ON” to put the game into the test mode. The test mode is used to change the fee charged for a game, and to set and test various game functions. (see illustration 5—3) Volume 1 control Rotate the volume control to adjust speaker sound level for your location. Volume 2 control Rotate this knob to even the sound between the front and back speakers. Credit switch This switch is used to increase the number of credits without activating the coin counter.

5-3 Test Mode Trigger buttons 1 through 4 on the Gun Assembly (illustration 5-2) are used to select the individual screens and various line item settings contained on each screen.

TRIGGER 4

TRIGGER 1

Illustration 5-2, GUN ASSEMBLY

Page 10

Pressing trigger buttons “3” and “4” will change the selected (red) items and pressing trigger button “1” will display the selected test screen. While in any of the test screens:

5-3-1

5-3-2 Options can be selected by pressing trigger buttons “3” or “4”.

Options can be activated by pressing trigger button “1”.

Values of the selected options are INCREASED by moving the trigger handles LEFT and DECREASED by moving the trigger handles RIGHT. To exit any screen, press trigger button “2”.

When testing or option changes have been completed, turn the test switch to the “OFF” position. The Game Play Screen will always reappear from whatever test screen is being displayed at the moment.

Main Test Menu

The main test menu screen (illustration 5-3) is activated by using the test switch on the Service Panel located inside the coin door. There are seven

separate test mode screens (listed here) which can be used to change game fees and test various functions of the game. Select the test to be performed by using the gun controls listed above.

~ TEST MENU - SEE SECTION

GAME OPTIONS ~ 5-8-2 SwiTcH Test ———}— 5-0-8 SOUND TEST —— p— 5-0-4 EFFECT TEST 5-3-5 MONITOR TEST —— }— 5-3-6 OBJECT TesT ————}— 587 ADS MODE 53-8

IN = PUSH SHOOT 1 SWITCH EXIT = TEST SWITCH OFF

Illustration 5-3, TEST MENU SCREEN

Game/Coin Option Screen After selecting the Game Option Screen (illustration 5—4), any one of nine different options can be changed using the gun controls.

  • GAME OPTIONS ~ GAME COST: 3 COINS 1 CREDIT DISCOUNT CONTINUE: YES COIN 1: 1 COIN COUNTS AS 1 COIN COIN 2: 1COIN COUNTS AS 1 COIN ATTRACT SOUND: ON = ——— DATA SAMPLING: OFF SHIELD: 2 RANK. B FREE PLAY: NO (a) (b) © NOT USED co} (e)

@) (hn

EXIT = PUSH SHOOT 2 SWITCH

Illustration 5-4, GAME OPTION SCREEN.

Page 11
  • The Game cost can be from 1 to 9 coins per credit.
  • The half price to continue rounds up to the nearest whole number. (For example, 3 to start, 2 to continue: or 4 to start, 2 to continue).
  • The number of logical coins per physical coin can be adjusted from 1 to 9.
  • The attract sound can be turned “ON” or “OFF” (we suggest “ON”).
  • The “ADS MODE” (bookkeeping) option can be removed from the Main Test Menu by selecting “OFF”. No bookkeeping will be kept if this option is “OFF”
  • The Shield damage level can be adjusted between 1 (easy) and 8 (hard).
  • The difficulty (Rank) can be adjusted between “A” (easy) and “D” (hard).
NOTE: Adjusting the Shield Damage (f) is more effective than adjusting the Rank (g).
  • The Free Play option can be turned “ON” or “OFF”. The games will be tracked in the bookeeping as if they were paid games.

5-3-3 Switch Test Screen The Switch Test Screen (illustration 5—5) provides test displays for all STARBLADE™ switches and potentiometers. =

  • SWITCH TEST -
TESTSWSERVICE SW—}—a

DIPSW =: 12345678 - (b) COIN 1 COIN 1 - COUNT 0 —-}+—

COIN 2COIN 2- COUNT 0 —NOT USED

STARTSW 1 a ()

VOLUMEX=" Y="*2(e)

SHOOTSW 1234 (f)

TIME **HOUR **MIN **SEC—(9)

EXIT = PUSH SHOOT 2 SWITCH

Mlustration 5-5, SWITCH TEST SCREEN

  • When lighted red, “TEST SW” indicates a normal operation. “SERVICE SW” should turn red whenever the Credit switch, inside the coin door, is pressed.
  • The status of the DIP switch on the game PCB board (CPU-PCB) is indicated by this display. Any number opposite DIP SW (switch) that is lighted red indicates that it is turned on.
  • When the coin 1 switch is closed, “COIN 1” will turn red indicating proper operation. The number shown indicates the number of times the switch has been triggered. The coin counter will not advance.
Page 12

5-34

5-3-5

  • When testing the Start Switch, the “1” should turn red whenever the start button is pressed.
  • This tests the operation of the gun potentiometer. Values increase when the gun is moved up or to the right, and decrease when its moved down or to the left. Moving left and right will change the value X. Moving up and down will change the value of Y.
  • When pressing a gun trigger, the appropriate number should turn red, (Pressing Trigger “2” will Exit this test and return you to the Main Menu).
  • This display indicates the amount of time the game has been on.

Sound Test Screen The Sound Test Screen allows for selection and playing of specific sounds. This can be useful when replacing speakers or adjusting the stereo volume.

~ SOUND TEST -

FM a eal PSG Se ae). vox ° ———j7— © STEREO CHK = ————}—. (a)

START = PUSH SHOOT 1 SWITCH EXIT = PUSH SHOOT 2 SWITCH

Illustration 5-6, SOUND TEST SCREEN

Use the gun controls, explained previously in section 5-3, to test the various sounds. Trigger “1” starts the selected sound.

  • The FM option tests “Filed Music” or digitally created sounds.
  • The PSG option tests both (a) and (c) combined. This is where most of the actual game play sounds are stored.
  • The VOX option includes digitally recorded sounds and voice.
  • When the STEREO CHK option is played, a tone scale is sent to the right speakers and then the left speakers.

Effect Test Screen The Effect Test screen (illustration 57) tests the various mechanical mechanisms and lamps using the gun controls.

Page 13
  • EFFECT TEST —
HITLAMP—-
REAR 1LAMP——}— norused

2 LAMP. ——}— NoTusep

FLASHLAMPeames |= (5)
STARTLAMP——}— norusep

VIBRATION 1 ——}— 2 —F nv 3 MEE) 4 —- @

DIRECT:0—— (e)

ON = PUSH SHOOT 1 SWITCH EXIT = PUSH SHOOT 2 SWITCH

Illustration 5-7, EFFECT TEST SCREEN

  • Hit Lamp activates the LED's in the center of the gun when selected.
  • This option flashes both strobe lights (above the mirror) when selected.
  • Vibration 1, 2, and 3 momentarily activates the vibration assembly mounted on the back of the seat.
  • Vibration 4 continuously activates the vibration assembly until the trigger button is released. CAUTION: Do not activate the motor continuously for more than 2 minutes.
  • Direct (0 — FF) activates various combinations of effects (a) — (d).

5-3-6 Monitor Test Screen <a SSS SS SS SD

DANGER HIGH VOLTAGE I THE MONITOR CONTAINS LETHAL HIGH VOLTAGE. THE MONITOR IS ] TO BE SERVICED BY A QUALIFIED SERVICE TECHNICIAN ONLY.
  • MONITOR TEST ~

COLOR BAR (a) CROSS HATCH (b) SIZE CHECK ()

IN. =PUSH SHOOT 1 SWITCH EXIT = PUSH SHOOT 2 SWITCH

Illustration 5-8, MONITOR TEST SCREEN

  • The Color Bar test sends a pattern to the screen that is used to adjust the red, green, blue and brightness levels. Adjustment should not be necessary, but can be made by a qualified service technician.
  • The Cross Hatch test sends a grid to the screen to be used for adjusting the monitor convergence. Adjustment should not be necessary, but can be made by a qualified service technician.
  • Size Check sends a grid to the screen to be used for adjusting the monitor height, width, and position. Adjustment should not be necessary, but can be made by a qualified service technician.
Page 14

5-3-7 Object Screen This screen is used to display STARBLADE™ polygons and graphics.

~ OBJECT TEST -

EXIT = PUSH SHOOT 2 SWITCH

Illustration 5-9, OBJECT TEST SCREEN

  • This option is used to change the object being displayed (0 — 3F5).
  • This does not affect the displayed object and is not used in this game (0-F.
  • This option Zooms the object larger (3FF) and smaller (0) (0 — 3FF).

5-3-8 ADS Screen The Automatic Data System screen provides detailed game information such as length of time the machine has been on, the number of minutes the game has been played, the number of games played, the number of games continued...etc.. This screen can be useful in adjusting the game for

maximum income.

(ON TIME ‘START CONTINUE TOTAL START (a) CONTINUE (b) CLEAR ADS DATA: NO ©)

IN = PUSH SHOOT 1 SWITCH EXIT = PUSH SHOOT 2 SWITCH Illustration S-10, ADS MENU SCREEN

  • Selecting the Start screen displays the number of first credit games and at what section of the game (section 1, 2, or end) the player died.
  • The Continue screen displays the number of games continued and which section the player continued from.
  • Selecting “YES” and pressing Trigger “1” will erase all the ADS

results to date.

5-4 DIP Switches The DIP switches are on the CPU-PCB of the Game PC boards (see section 7-5). Switch 1) Secondary Test Switch. Selects the test mode (see Section 5-3).

Switch 2-7) Not used. Always off.

Page 15

Switch 8) Screen Stop. When selected, the screen will stop whenever Trigger 3 is depressed. Some scenes cannot be stopped, however.

NOTE: When playing a game, all switches must be in the “OFF” position or the machine will not function properly.

5-5 Monitor Adjustment The monitor remote adjustment control is attached to the left side of the monitor chassis. O O

[o) [o) ‘TOP ROW- LEFT TO RIGHT

Va103: VERTICAL POSITION Vitto2 BLACK LEVEL Vator -conTmasT VR 109 VR 102 VR 101 BOTTOM ROW - LEFT TO RIGHT VR 106- HORIZONTAL POSITION VR 105 - VERTICAL HOLD VR 104- VERTICAL SIZE VR 106 VR 105 VR 104

Illustration 5-11, MONITOR REMOTE ADJUSTMENT BOARD

5-6 Gun Adjustment STARBLADE™ will not operate correctly if the game PC board, ROM, gun assembly, and the control potentiometers are not adjusted after being replaced. Always carry out the steps listed below when replacing parts.

  • Open the coin box door.
  • Turn the test switch to the “ON” position while holding down the service switch. Screen 1 will appear.

~ LEVER SETTING — — LEVER SETTING —

  • LEVER SETTING — X SIDEABS: 00 Y SIDE ABS: 00 LEFT: 00 LEFT: 00 CENTER: 00 CENTER: 00 RIGHT: 00 RIGHT: 00 SET LEVER LEFT-DOWN SIDE MAX SET LEVER RIGHT-UP SIDE MAX ‘AND PUSH SHOOT 1 SWITCH ‘AND PUSH SHOOT 1 SWITCH

VOLUME : X = 00, Y = 00 AGAIN = PUSH SHOOT 1 SWITCH EXIT = PUSH SHOOT 2 SWITCH VOLUME : X = 00, Y = 00 VOLUME : X = 00, Y = 00 EXIT = PUSH SHOOT 2 SWITCH EXIT = PUSH SHOOT 2 SWITCH

SCREEN 1 SCREEN 2 SCREEN 3

Illustration 5-12, GUN AIMING SCREENS

  • Adjust the gun as follows. a. Aim the gun down and to the left as far as possible, and pull the right trigger. Screen 2 will appear. b. Aim the gun up and to the right as far as possible, and pull the right trigger. Screen 3 will appear. c. Compare the gun movement to the screen display. If everything is displayed correctly, press the right thumb button. If not, press the right trigger and readjust the potentiometers.
NOTE: If the gun aim does not line up with the line of shot displayed on the screen during game play, repeat the above procedure.

il

Page 16
  • HOW TO PLAY

STARBLADE™ is a 1st person space combat simulator that utilizes a hemispherical mirror to display various types of enemies which the player attempts to shoot with the gun.

After inserting the proper coins, the player starts the game by pressing the start button. The player then becomes the U.G.S.F.'s top gunner in the flagship “GeoSword”.

Once the start button has been pressed, the player receives a short (45 second) briefing. The federation's home planet is being attacked by a mechanized planet called “Red Eye.” Operation STARBLADE is to achieve two objectives; 1. defend the home planet, and 2. destroy “Red Eye”. The briefing can be aborted by pressing the start button.

After the briefing, the player and his ship (the FX-01 GeoSword) are then launched into space to defend his attack fleet and protect the mother planet. Every time the player is hit, the hit lamp (in the center of the gun) will flash and the shield power will be decreased. Most of the enemies shots can be destroyed before they can damage the GeoSword.

The enemies retreat through warp space to “Red Eye” and the GeoSword is directed to breach the enemy defense barrier and destroy the mechanized planet. After “Red Eye's” power source (Octopus) has been destroyed (resulting in the destruction of the planet) the GeoSword then encounters additional fighters and an enemy battleship (Iceberg) and is ordered to destroy them.

The battleship is eliminated by entering the ship and destroying the power

source.

While evacuating Iceberg, the GeoSword encounters the enemy commander and the player must destroy him. The object of the game is to shoot all the enemies and finish all three levels for the best possible score. For rapid fire, any one of the four (4) trigger buttons can be held down. All four buttons fire the same weapon so that players can use the buttons that are most comfortable for them.

Once the player's shields run out the game ends, but the player can always continue.

Players who finish the game with the highest scores can enter their initials into the Hall of Great Fighters.

Page 17
  • MAINTENANCE

BE SURE TO TURN THE POWER OFF BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.

7-1 Marquee and Fluorescent Lamp Replacement

  • Using the wrench provided, remove the six (6) tamper proof screws holding the marquee acrylic in place.
  • Remove the marquee acrylic.
  • Replace the fluorescent lamp (20W) and/or the marquee.
  • Reverse these steps to reassemble.

7-2 Gun Assembly Replacement

HEX HEAD GUN ASSEMBLY BOLTS (4)

Lu TAMPERPROOF SCREWS (14) T tm

GUN BASE COVER

Illustration 7-1, GUN ASSEMBLY REPLACEMENT

  • Remove the fourteen (14) tamperproof screws holding the purple gun base covers (right and left side) in place, and carefully remove the covers.
  • Remove the one (1) phillips screw securing the ground wire to the side of the gun assembly.
  • Remove the four (4) hex head bolts holding the gun assembly to the purple

gun base.

  • Carefully lift the gun assembly, disconnect the two (2) wire harness connectors and remove the assembly from the game.
  • Reverse these steps to reassemble.
Page 18

7-3 Hemispherical Mirror Replacement and Cleaning

CAUTION: The mirror is easily scratched or damaged if not properly handled. CLEANING: Use only 100% cotton or cheesecloth and a non-abrasive plastic cleaner.

)

2) 3) Open the rear door and loosen the eight (8) screws of the lower four retaining brackets. Remove the upper two retaining brackets. Slowly lift the mirror up and out of the lower brackets to remove.

7-4 Vibration Assembly Replacement

1)

2)

3) 4)

5) Illustration 7-2, VIBRATION ASSEMBLY

Using the wrench provided, remove the eleven (11) tamperproof screws holding the yellow seat back in place and carefully remove the seat back. Remove the metal vibration assembly cage by taking off the four (4) hex nuts on the ends of the cage. Disconnect the power connector for the vibration assembly. Remove the four (4) locking hex nuts retaining the vibration assembly and carefully remove the assembly from the seat frame. Reverse these steps to reassemble.

7-5 Game PC Board Removal

1) 2) 3)

4)

5)

§)

i) Insure that the game is unplugged. Carefully open the lower back door. Disconnect the power leads (on the bottom of the PCB cage) and the main harness connector (on the top of the PCB cage). Remove the four (4) phillips head screws (2 on each side) mounting the PCB cage to the rear door. Remove the four (4) phillips head screws (1 on each corner) securing the cage lid to the PCB cage and carefully remove the lid. The four (4) PCBs can be removed individually by sliding them straight out of the

cage. Reverse these steps to reinstall the PCBs and PCB cage.

Page 19

7-6 Monitor Board Access

ae een en eee ee Od I DANGER HIGH VOLTAGE I | THEMONITOR CONTAINS LETHAL HIGH VOLTAGE. THE MONITOR IS TO BE SERVICED BY A QUALIFIED SERVICE TECHNICIAN ONLY. Mn cs ee ee a You will need a ladder or step stool to remove the monitor board. Remember to use

caution when standing on or climing any ladder.
  • Remove the six (6) phillips head screws securing the uppermost panel on the top of the monitor cabinet and remove the panel.
  • The monitor board can only be asccessed from the top of STARBLADE™.

7-1 Monitor Tube Removal

palate toeteetaetentgelgslenlandeetenlneesligeteelerieatentantanleslonteatan | l DANGER HIGH VOLTAGE l | THE MONITOR CONTAINS LETHAL HIGH VOLTAGE. THE MONITOR IS LL. _ TOBE SERVICED BY A QUALIFIED SERVICE TECHNICIAN ONLY. = ee a a oe SS SP SS SS A

  • Inside the mirror cabinet, above the gun assembly, remove the eight (8) phillips head screws retaining the monitor bezel and remove the bezel.
  • Disconnect the monitor board (see section 7-6 for monitor board access).
  • Carefully remove the four (4) hex bolts holding the monitor tube in place.
CAUTION: The monitor tube is secured by these four bolts only.
  • The monitor will slide out of the front of the monitor cabinet towards the mirror. Be cautious not to scratch the mirror when removing the CRT.
  • Reverse these steps to reinstall the monitor tube.
NOTE: To remove the entire monitor, it is suggested that STARBLADE™ be disassembled first to remove the monitor safely.

7-8 Strobe Lamp Replacement

  • Open the upper rear door and unplug the harness for the strobe assembly to be removed.
  • Using the wrench provided, remove the three (3) tamperproof screws holding the acrylic strobe cover in place.
  • Remove the two (2) phillips head screws holding the strobe assembly bracket

in place.

  • There are three (3) small phillips head screws on the back of the assembly that attach the strobe light to the bracket.
  • Reverse the above steps to reinstall the strobe assembly.
Page 20
  • TROUBLESHOOTING If you suspect the game may be malfunctioning, the following steps should be considered before you make a service request.
  • The power supply should be between 110-120 Volts AC. However, when some other equipment (air conditioners, multiple pinball games, air compressors, etc.) are connected to the same power source, the voltage may change beyond this range and cause game trouble or improper operation. To guard against this, each STARBLADE™ Cabinet should have its own dedicated power source.
  • When the game does not work with the power turned on, turn the power off once and then back on. This may restart the game. If it still does not work, inspect the fuses.
  • When the game PCB, the ROMs, the Gun Assembly, or the Potentiometers are replaced, it is necessary to make adjustment for the game to function normally. Make appropriate adjustments referring to section 56, Gun Adjustment.
  • If the gun aim does not line up with the line of shot displayed on the screen, refer to section 5-6, Gun Adjustment.
  • Check all wiring connections as malfunctions can be caused by loose connections.
  • Foreign substances, including dust, on the game PCB or on the monitor PCB, may cause malfunctions or improper operation. Check that the PCBs are clean.
  • When you make electrical checks, use the wiring diagrams for reference.
  • If the above suggestions are not applicable, or no improvement is observed, contact your distributor or the service office printed on the back cover of this manual.
  • DO NOT ATTEMPT TO REPAIR THE GAME PCB YOURSELF. Instead, please return the board to your distributor for any repairs. This PCB contains sensitive devices that could be destroyed even by the internal voltage of a multi-meter.
  • When sending parts to be repaired, make sure to pack them firmly with a complete explanation of the problem. When sending PCBs, package them in anti-static foam or bubble wrap, and pack them in cardboard boxes to protect against impact damage during shipment. To ship monitors, pack them in wooden frames so that CRTs and PCBs are protected against impact.
Page 21

Parts List

Page 22
  • PARTS LIST

‘TOP ASSEMBLY SB02-00288-00 ] [Trop ASSEMBLY (cont)

ITEMDESCRIPTION|PART NO.TEM)DESCRIPTIONPART NO.

—T

1 | Mirror Cabinet Assembly| SB05-00291-0030 | Clear Acrylic Strobe Cover| SB95-00315-00

Mirrorized Hemisphere $B90-00317-00 31 | Push Button, Purple VG80-00316-00

Monitor Cabinet Assembly $B05-00292-00 32 | EMI Line Filter (FCC) VG78-00476-00

SB95-00302-00 33] STARBLADE™ Speaker Grill $B10-00318-00 at 4 | Plastic Mirror Bezel, Top

We

Plastic Mirror Bezel, Bottom$B95-00302-0134 | Well Nut Threaded InsertVG20-00486-00
Isolation Mount Coverlll $B95-00302-0235 | Top Tube Mount Plate$B10-00489-00
Strut CoverSB95-00302-0336 | Monitor Box Support| SB10-00490-00
Namco Strobo Assembly$B03-00293-0037 | Mirror Mounting Bracket$B10-00491-00
9 | Vibrating Seat Frame Assembly | SBO5-00298-0038 | Top Monitor Bracket$B10-00492-00
10 | Seat Base Assembly‘SB05-00299.39 | Monitor Box Support| $B10-00493-00

11 | Over/Under Coindoor VG83-00045-00

SB03-00297-00 Se 12 | Namco System 21 PCB Assy. ee 13 | Namco Hit PCB Assembly SB03-00296-00 14 | Namco SB Gun Assembly Graphics Kit Assembly SB04-00295-00

$B05-00301-00 40 | Kick Diamond Plate $B10-00494-00

$B10-00495-00 41 | Strobe Mount Bracket este 42 | Fuse Holder $-8202-2 (UL) VG52-00496-00 43 | Label, 0.2 Amp Fuse (UL) 44 | Label, 2 Amp Fuse (UL) VG52-00477-00

VG52-00478-00

16 | 25 Inch Standard Monitor VG85-00358-00 45 | Spacer #41 (UL) VG10-00497-00 46 | Cord Clip ACC38-A-M (UL)

17 | Isolation TransformerVG56-00245-00VG51-00498-00
18 | Isolation TransformerVG56-00174-0047 | Enclosure Coin HousingVG10-00465-00

ja zene

19 | 2Amp Quick Acting FuseVG52-00477-0048 | Plate Door LockVG10-00446-00

ae

20 | 0.2 Amp Quick Acting FuseVG52-00478-0049 | Bracket, Power Supply Mount| VG10-00499-00
21 | Plastic 25" Monitor Bezel$B95-00303-0050 | Box, Plastic CashVG90-00466-00
22 | Fluorescent Lamp AssemblyVG57-00058-0051 | Cover, SerialVG95-00500-00

23 | 80 CFM Fan VG55-00060-00 lis 52 | Strobe Light Window $B95-00501-00

24 | Fan GuardVG55-00061-0053 | Bag, 40 x 34 x 81 PlasticVG60-00502-00
25 | Speaker, 5"VG54-00062-0054 | Lamp FiST8GWVG57-00059-00
26 | Speaker GrillVG10-00485-0055 | STARBLADE™ Plastic Marquee | SB90-00324-00
27 | XT Type Power SupplyVG88-00080-0056 | Strut Mounting Plate$B10-00375-00
28 | Ferrite Clamp (FCC)VG78-00198-0057 | Enclosure, Transformer$B10-00526-00

29 | Ferrite Housing (FCC) VG78-00199-00 58 | Cover Under Wire $B10-00527-00

Page 23

9. PARTS LIST (cont.)

‘SHIPPING ASSEMBLY SB01-00286-00 HARNESS ASSEMBLY SB05-00528-00

DESCRIPTION PART NO. ] Tem) DESCRIPTION PART NO.

Product Carton| SB60-00287-00 |1 | Main Wire HamessSB50-00509-00
STARBLADE™ Top Assembly| SB02-00288-00 |2 | DVAV Ext.SB50-00510-00
Operator's ManualSB45-00289-003 | Gun Wire Harness$B50-00511-00
FCC NoticeVG46-00031-00Monitor Light Wire HarnessSB50-00512-00
Serial Number LabelF246-00032-00 |5 | Speaker Motor Wire HarnessSB50-00513-00

UL Label VG46-00085-00 | Manual Poly Bag

Game Poly Bag

Shipping Label Namco

Box, Seat Frame

Box, Monitor VG60-00098-00

SB46-00488-00

SB60-00487-00

$B60-00505-00 7_| Start Ext. Wire Harness

8 | Power Ext. Wire Harness 9 | Speaker Ext. Wire Harness [10 | Gun Ext. Wire Harness TSA Bracket Wire Harness

12 | Coin Door Wire Harness 13 | Lamp Pigtail 14 | IBM Power Cord Mod. 15 | Monitor Ext. 6 | Motor Ext. Wire Harness $SB50-00514-00

SB50-00515-00

SB50-00516-00

$B50-00517-00

SB50-00518-00

SB50-00519-00

SB50-00520-00

SB50-00521-00

SB50-00522-00

$B50-00523-00

Marquee Acrylic Panel

Side Decal, Top Right

Side Decal, Top Left

Overhead Decal

Control Panel Overlay $B40-00395-00 SB40-00389-00

$B40-00394-00

SB40-00396-00

SB40-00399-00 16 | #6 Spade SB50-00524-00

Monitor Cabinet Decal, Left

Monitor Cabinet Decal, Right SB40-00393-00

$B40-00392-00 MIRROR CABINET ASSEMBLY SB05-00291-00

ITEM) DESCRIPTION

Mirror Cabinet l PARTNO. $B63-00371-00

Color T Mold 25/32 VG90-00372-00

Caster, 360 Swivel VG24-00373-00 8 | Seat Back Panel, Top SB40-00398-00 9 | Seat Back Panel, Bottom $B40-00397-00 |_10 | Side Decal, Bottom, Left | $B40-00391-00 11 | Side Decal, Bottom, Right $B40-00390-00 12 | Front Top Left $B40-00474-00 13 | Front Top Right $B40-00475-00 VG83-00165-00

Leveler Plate $B10-00507-00 4 | Lock 2255

Bottom Door Hinge $B10-00506-00

Page 24
  • PARTS LIST (cont.)

Diamond Plate

Frame Support Bracket

Bottom Mounting Plate End Caps Caster, 360 Swivel

Isolation Mount Washer Isolation Mount Nut $B20-00503-00 $B10-00480-00

$B10-00481-00

$B10-00482-00

$B10-00483-00

$B10-00484-00

VG24-00373-00

$B20-00504-00 VIBRATING SEAT ASSEMBLY SB05-00298-00 NAMCO SYSTEM 21 PCB ASSEMBLY SB03-00297-00 [rem] DESCRIPTION PART NO. Trem] DESCRIPTION PART NO.

1 _| Namco Vibrating Assembly$B04-00294-001EMIPCB$B03-00361-00
2 | Seat Frame$B10-00376-002|CPUPCB$B03-00362-00
3 | Hunsaker Seat}Dv20-00092 -003 | PGN (B) PCB$B03-00363-00
4 | Plastic STARBLADE™ Seat Back | SB90-00378-004) DSP PCB$B03-00364-00
5 | Rubber Isolation MountSB04-00380-005 | OBJPCBSB03-00365-00
6 | Control, Left Top Panel$B10-00400-006|MOTHER PCB| $B03-00366-00
7 | Control, Right Top Panel$B10-00401-007 | AMP (B) PCB$B03-00367-00
8 | Control, Bottom Bracket$B10-00402-00| 3] DRIVE PCBSB03-00368-00
9 | Seat Bottom Bracket$B10-00406-009 | Metal Chassis$B03-00369-00
Diamond Strip Protection$B10-00479-0010 | Metal EMI Panel$B03-00370-00

SEAT BASE ASSEMBLY SB05-00299-00

‘Strut Mounting Plate $B10-00375-00

VG20-00384-00

$B10-00482-00

‘SERVICE PANEL ASSEMBLY VG05-00314-00 [ MONITOR CABINET ASSEMBLY SB05-00292-00 iTeM DESCRIPTION PART NO.

1 | Coin Counter PART NO. rem DESCRIPTION VG83-00166- Monitor Cabinet SB63-00374-00

2 | Service Panel, STARBLADE™ VG10-00387-00

  • | Color T Mold 5/8 VG90-00508-00
Page 25
  • PARTS LIST (cont.)

9-1 Vibration Assembly

255-505 255-507 255-506 / | 255-503

255-502 255-501

| NAMCO VIBRATING ASSEMBLY SB05-00298-00 ITEM DESCRIPTION PART NO. 1 | Vibrator Base 255-501

  • | Motor Bracket 255-502 | 3. | Weight 255-503 4 | Pillow Block UCP201 255-505 5 | K-Coupling 5802 (10x10) |_ 255-506 6 | Reversible Motor, SRK40A-A | 255-507
Page 26

oF aoe i) ‘ i YOR S ; So ies —(Sy* ] as, LQ

O Od | \ LY >; ©) ®

ane ae

9-2 Gun Assembly

@) @ G4)

  • PARTS LIST (cont.)
Page 27
  • PARTS LIST (cont.)

GUN ASSEMBLY GUN ASSEMBLY (continued)

ITEMDESCRIPTIONPART NO.ITEMDESCRIPTIONPART NO.
1_|Controller Cover255-60123 | Spacer255-623
2 | Indicator Cover255-60224 | Spur Gear (Y)255-624
3 | Neck255-60325 | Volume Bracket255-625
4 | Core Shaft255-60426 | Slide Hole255-626
5 | Bottom255-60527 =| T Spring (A)255-627
6 | Outside Cover255-60628 | Angle255-628
7 | Inside Cover255-60729 | Grip (RA-SB)255-629
8 | Arm255-60830 | Grip (RB-SB)255-630
9 | Frame (Left)255-60931 | Grip (LA-SB)255-631
10 | Frame (Right)255-61032 | Grip (LB-SB)255-632
uiFrame (Front)255-61133 | Gear246-140
12 | LED Bracket255-61234 | Spur Gear (S76B20B+0306)231-093
13Pipe End255-61335 | Spur Gear (S75B32B+0306)231-633
14 | Slide Plate255-61436EP Bushing (LFF-3220)255-634
15 | Grip Plate (Left)255-61537 | EP Bushing (LFF-3020)255-635
16 | Grip Plate (Right)255-61638 | Rhombic Flange Unit (UF1001)|255-636
17_|Roller255-61739 | Button244-009
18 | Volume Plate255-61840 | Button Joint244-029
19 | Pipe Stay (P)255-61941 | KB Switch000-055
20 | Pipe Stay (Y)255-62042 | KB Sub PC Board (B)224-030
21 | Stopper Rubber (P)255-62143 | Volume EWS-UOA20E53008-006
22 | Stopper Rubber (Y)255-62244 | Hit PCB255-637
Page 28
  • PARTS LIST (cont.)

9-3 Coin Control Assembly

a\\e 91-1911-16 Bk }—— 91-1113-01

LS Biber ‘es \ ss 91-0604-16

90:1000-00 _.¢2 ™ 90-1017-00 | psrooaoet| || tone 4] =

91-1917-00 -B4 91-1118-00

  • 91-0502:16 M Va

(GOSLo1-s14600

90-1206-02biat 91-1120-00ee’
o8\oO108-0or”
92-1002-08 “ar, 2 >hy91-1108-01a
92-1002-09~ '“T-91-1106-00,ieeeue

see al 102200 20-4179-00 91-1036-00 36:00 3.415001 #-— 90-1003-00 12-4050-01 S | era | 91-0506-00

92-1002.07 i 91-1108:00 St 90-1007-00

  • y a7 LP} 81-1128.00 2

} ' |v

92-1002-11 a“ 91-1110:00 91-1116-16

90-1032.00

COIN CONTROLS COIN DOOR ASSEMBLY

Page 29
Scan of page 29

This page is a drawing, shown as the original scan.

Page 30

u

| 3 ti __ spear mont wc] | [=F | 6. <—<$—= HB | Fae HE i SPEAKER FRONT LEFT MIRROR BOX ASSY

owen suey sic SWITCH BOX ASSY ‘a

(tte|a
aierOe;im
—E-i||Seed
(J)ee) vo wa,t
&hia)elTh we

. caw aoc

Htaf}saeate
;eyao

i i

POWER SUEPLY PLATE ASSY DRCSESTOeS EAL Macogcgece 1 meen

ig 2 tate wae ee eet | ore roe AEB Ss rr

i | ow | i

BROWN ‘OREN WATE owt ewe PINK ~B=ge NOTES: |. CONNECTOR UNLESS OTHERWISE SPECIFIED, INDICATE MINI UNIVERSAL MAINTAIN LOCK. 2, APPLY SOCKET COVTACT FOR PLUG CONNECTOR, AND PIN CONTACT FOR CAP CONNECTOR.

  • THN, UNES UNLESS OTHERWISE SPECIFIED. INDICATE ANG24. AND THICK LUNES AWGIE. ‘5 CORE TIRE CORO WITH PLU.

‘TAB OF TRANSFORMER INDICATES. 240,220,200, (OR 120, 115,110V RESPECTIVELY. ADMUST ITS. CONNECTION’ FOR INPUT POWER VOLTAGE APPLY 34 FUSE FOR 200¥,240V AND 5A FUSE FOR "IOV, 120V.

STARBLADE™ — Wiring Harness Diagram

Page 31

EXTERIOR LAMP

GUN Assy. TRIGGER SWITCH | i Caen [_ SSS ewe | ate Gr Rea re cus H

myi3 ean
SariayBF ean |
eteBANE — otay
eaeelFyomecnow |
anewae,YOuME

an we fe ete — et Fy occnow |

SSERMCE SWITCH SW7 © TEST swTcH sws Fes Leet me (Co a wee REAR

STARBLADE™ — Wiring Harness Diagram

Page 32

namco

NAMCO-AMERICA, INC. 3255-1 Scott Bivd., Suite 102 Santa Clara, CA 95054-3013 (408)496-6371 FAX: (408)496-6399

Reorder Number SB45-00289-00

WWW.DRAGONSLAIRFANS.COM