Space Battle
Space Battle (Entex) (Entex, 1979) · Manual · 15 pages · 10 sections · original scan
MopEL SB-OO2U
SERVICE MANUAI
=———
CONTENTS
. SPECIFICATIONS . INSTALLATION . PLAY INSTRUCTIONS , . . }, OPERATIONAL INSTRUCTIONS .. OPERATER’S OPTION .... » TROUBLE SHOOTING
- PARTS DIAGRAM OUTSIDE VIEW INSIDE VIEW CONTROL LEVER ASSEMBLY .. WIRING DIAGRAM
- PARTS LIST
@ C.P.U BOARD SCHEMATICS-1 ... 12 @ C.P.U BOARD SCHEMATICS-2 ... PWN QRWNaA = a
- SPECIFICATIONS
Power Source ....... 00000000 Single-phase 50/60Hz A.C. 240, 220, 117, 110 or 100V (all within +10%) Wattage 2. ieee cece eee eee 120W (at 100V) Coin Operate ..... . 1 to 6 games per 1 coin; 1 to 4 coins for 1 game Coin Capacitance 3,000 coins (¥100 coin) Dimensions; Width 2.0... ccc cece eee eee 620 mm Depth ...........0....220005 800 mm Height. wwcwad cc. s weer eed 1,700 mm CRT monitor ..............0005 20" color CRT with smoke mask Power Cord .......-..00ee ee eee Triple captyre/ 3 m in length
- INSTALLATION
- Install the machine on a flat floor.
- Avoid locations subjected to direct sunlight, high temperature, high humidity, vigorous vibrations, dust, etc. Also avoid locations where dangerous objects or fire-fighting apparatuses are stored or which block the emergency exit.
- Don’t give any shock or vibrations to the machine.
- Don't allow any metal objects to fall into or water to get into the cabinet.
- When applying voltage on the machine, do not use the same wall outlet as the one for motors, air conditioners, etc. which tend to fluctuate the voltage of the machine or to produse noise.
- The line voltage that may be selected is as follows: single-phase 50/60 Hz A.C. 240, 220, 117, 110 or 100V. Connect the plug to the socket which is fitted your local voltage. This Voltage Selection Connectors are located on Power-Transformer.
3. PLAY INSTRUCTIONS
*
* After coin inserted, press either 1 or 2 PLAYERS BUTTON.
Operate your BATTLE STATION right or left by CONTROL LEVER. And shoot assulting enemies.
Your BATTLE STATION gradually sails up in the sky.
7 enemy ships are all destroyed, the 1st round is over. When the 8th round is over, return to the 1st round.
When each round is over, if the cities on the ground remains, add the number of cities for your score as BONUS points.
All your reserved BATTLE STATIONS are destroyed, the GAME is over.
SCORE
OA Ad *
————— ENEMY SHIPS REMAINING CITIES ALL ARE 10 PTS. EACH 50 PTS.
°
4. OPERATIONAL INSTRUCTIONS
Be sure to turn off the power switch before working on the machine.
Avoid momentarily pushing in or pulling out the power cord plug.
Even when it is found that the solid-state module is apparently out of order, do not check for the circuit by means of a tester, etc. since the voltage developed within the tester, etc. may destroy the IC unit.
When carrying the machine about, be careful not to drag or drop it so as to protect the CRT of its TV set.
Be sure to use rated fuses.
© Since there are high-tension parts on the base board and in the interior of the TV set, never touch such parts (this rule, however, does not apply to the manufacturer's servicing engineers).
OPERATER’S OPTION
1, AUDIO VOLUME ADJUSTMENT
- OPTION SWITCH SETTINGS
DIP SWITCH
| FUNCTION = | —~ | a | : | - | FUTURE |
DIFFICULTY OFF DIFFICULT ON __| EASY
| COIN | OFF | OFF | 1 GAME/1 COIN | |||
| OPERATE | ON | OFF | 1 GAME/2 COINS | ||
| (CHUTE 1) | OFF | ON | 1 GAME/3 COINS | ||
| ON | ON | 1 GAME/4 COINS | |||
| COIN | OFF | OFF | 1 GAME/1 COIN | |||
| OPERATE | on | OFF | | 2 GAMES/1 COIN | ||
| (CHUTE 2) | OFF | ON | | 3GAMES/1 COIN | ||
| ON | ON | 6 GAMES/1 COIN | | |||
| June 0G / 8 | Ded | We RIACk | fron | # & | ve |
| ba | ~ | g | bo 7A | yor a | Qo |
5. TROUBLESHOOTING
© Before considering some phenomenon as a trouble, confirm the matters listed below and then contact your dealer.
© The video game machine is broadly divided as to electrical component into four sections, namely, the minitor section, game PCB, operating section and power source section, which are connected with one another by wiring. If any one of them develops a trouble the game machine as a whole will not work normally. When you think that there is something wrong with the machine, check for the machine just for a little while before consulting your dealer since an apparent trouble may sometimes be caused by a trifling mistake or misunderstanding which can be remedied by a modicum of repairs.
© When the machine has developed any trouble, it must first be found out which part of the four sections and the wiring is malfunctioning. When you have guessed the malfunctioning part, check for each section. If the checked part shows no abnormal signs, check for other parts related to it, too.
© Is the fuse not blown ? (Be sure to use the indicated fuse. If a renewal fuse is also blown, then the other part is out of order.)
© Is the connector unfirmly contacted or disconnected ? Since connector’s poor contact is conceivable in all trouble cases thoroughly check the connector for contact condition (Be sure to turn the power off before mounting or demounting the connector.)
© Sometimes normal images cannot be produced despite turning ON the power cord plug. This can sometimes be corrected by setting the control circuit. So, repeat turning ON and OFF the power a few times.
© When checking for the meters, switches, etc. by means of a circuit tester, be sure to pull out the IC board connector.
6. PARTS DIAGRAM
¢ OUTSIDE VIEW
L Fixture (062)
Acrylic Tytle Panel (058-2)
Acrylic Play field Panel (058-1) Acrylic Smoked Mask (033) 20" Color CRT Monitor (042)
Sticker (034)
Operating Lever Ass’y (071) Push Button Ass‘y (016-R) Operating Panel (008)
Players SW (010)
Front Door (066)
[Front Door] Coin Slot #2 Coin Slot #1 (Cash Box)
Sylinder Lock (001-3)
Sylinder Lock (001-2) {Common key) Caster 3 Rear Access Door
e INSIDE VIEW
Fluorescent Lamp (059) 7 Seeker 8 ohm (032) (061) \
(060)
20" Color CRT (042)
(038)
Coin Counter (020) Synthesizer Board (051-2)
Cash Box (067) Game Board (051-1)
Interlock SW (064)
Cabinet (001) Power Cord
Power Souce Unit (048) (049)
e CONTROL LEVER ASSEMBLY
Spacer ring (018)
Long-Lever micro (019)
Push button fixture (017)
Molded push button Attached nut (016) P: yf Lever Knob idl
(015)
Operating panel g
Blind (012) el
Lever Assembly (011) Players SW Assembly {010-2)
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
t
7. PARTS LIST
Item No. Nomenclature Description Quantity Remarks
| 001 | Cabinet | Type 6500 | 1 | |
| 001-2 | Sylinder lock & key | (Common key) | 1 | |
| 001-3 | Sylinder lock & key | (Safe key) | 1 | ||
| 006 | Coin mechanism | 2 | Coinage specified | |
| 008 | Operating panel | 1 | ||
| 010-2 | Player’s SW | Round type | 2 | |
| 012 | Blind (black paper) | 10.56-400 | 1 | |
| 015 | Lever knob | 35¢ black | 1 | |
| 016-R | Molded push button ass’y | 1 | ||
| 016 | Molded push button | 1 | ||
| 017 | Push button fixture | (Upright) | 1 | |
| 018 | Spacer ring | 1 | ||
| 019 | Long-lever micro SW | 1 | ||
| 020 | Coin counter | 6VDC G6digit | a | |
| 021 | Service SW | Micro type | 1 | |
| 022 | Service SW fixture | 1 | ||
| 025 | | AC Outlet receptacle | 2 | ||
| 027 | Cord bush | 1 | ||
| 029-1 | Fuse clips | 1 | ||
| 030 | Noise filter | 1 | ||
| 031 | | 3A Fuse | 6@ glass cartridge | 1 | |
| 032 | Speaker | 6-8" 8 ohm | 1 | |
| 033 | Acrylic smoke | (Blue) | 1 | |
| 034 | Play instruction sticker | ~ | 1 | |
| 038 | 44p Edge connector | 4mm pitch | 1 | |
| 042 | 20" Color CRT monitor | Toei | 1 | Insulated; with signal |
cable & power cord
| 042-1 | Signal lead cable | For monitor | 1 |
| 042-2 | Power cord | For monitor | 1 |
| 044 | 7p relay plug & socket | 2 | |
| 045 | Triangle ideal | 4 | |
| 048 | Power source board ass’y | 1 | |
| 049 | Set down transformer | 1 | |
| 051 | Game PCB | 1 set | |
| 051-1 | Main (MPU) PC board | 1 | |
| 051-2 | Voice synthsizer board | 1 | |
| 058-1 | Playfield panel | Silk printed | 1 |
| 058-2 | Tytle panel | Silk printed | 1 |
| 059 | Fluorescent lamp ass‘y | AC 100V 10W | 1 |
| 060 | Monitor L fixture | 2 | |
| 061 | Mesh plate | For speaker | 1 |
| 062 | L fixture | For tytle panel | 2 |
1n
Item No. Nomenclature Description Quantity Remarks
| 064 | Interlock SW | 1 |
| 065 | Interlock SW fixture | 1 |
| 066 | Front door | 1 |
| 067 | Cash box | 1 |
| 068 | Cash box receptacle | 1 |
| 069 | Power source board fixture | 1 |
| 070 | 2p terminal board | 1 |
| 071 | Operating lever chassis | 1 |
071-1 | Spacer i 2 071-2 | Plate spring 4
| 071-3 | Handling lever | 1 |
- 071-4 Shaft 1 071-5 | Lever pin 1 o716 | U-ring 1 071-7 | R-ring 1
| 072 | Escutcheon (black paper) | 1 | |
| 073 | Patching lock | 2 | |
| 083 | Diode | Class 1A (10D-1) | 2 |
| 084 | 2p relay plug & socket | 1 |
_. aca a Ty ; 2 C h P
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.