CATHODE RAY TOMES

Major Havoc TM-252 1st Printing

Major Havoc (rev 3) (Atari, 1983) · Technical Manual · 76 pages · 72 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Alar, Inc California Customer Service Office 1105 N. Fair Oaks Avenue P.O. Box 427, Sunnyvale. CA 94086 Telex 17-1103 (Monday-Friday, 7°30-4:00 pm Pacific Time) eg From California, Alaska, or Hawaii oO @@ (408) 745-2900 em Service from anywhere in the area shown in white Oo @@ toll-free (800) 538-1611

EAST USA. Service only

Atari, Inc New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ame =From New Jersey 2° (201) 469-5993 = From anywhere else in this area © toll-free (800) 526-3849

EUROPE _

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

J 06252155

Page 3

The adventures © “ ( Sou \ ve ffi. fisig re ia

with

ustrated parts Lists

Page 4

© 1983 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 11M

Page 5

Notice Regarding Non-ATARI Parts

WARNING Use of non-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game. ¢ Modify or alter any circuits in the game by using kits or parts not supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated. inacommercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: ¢ Allgreen ground wires in the game are properly connected as shown in the game wiring diagram. ° The power cord is properly plugged into a grounded three-wire outlet. « The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage. © The EMI Shield PCB is properly installed and connected in series with the game PCB harness. ¢ All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.

iii

Page 6

Table of Contents

Set Up How to Use This Manual Game Overview .......... New Features . Installation Requirements Inspecting the Game ....... Voltage-Plug Selection and Fus : cee . ae Switch Locations ...... 65.0.0... 00. ee eee

Self Test Self-Test Displays ..............5 Was mwas yo ang Bee sai Self-Test Trouble Analysis ....... ian ee nO ee eu

Maintenance Cleaning Requirements ..........-....0000 0005 Pee eee Opening the Control Panel ........ . Pushbutton Leaf Switches ... . : aaie Removing the Roller Control Assembly bee Roller Control Maintenance... ... . Reassembling the Roller Control Assembly . Replacing the Coupler PCB Assembly Light and Speaker Board Assembly Lower Speaker.......... . Removing the CRT ‘Assembly see : Pan Wiring the Utility Panel Controls... .. . ee ee ee

Illustrated Parts Lists For a list of all illustrations in this manual, see following page 1-4 1-4

1-6

2-2 2-8

Page 7

List of Illustrations

Figure 1-1 Figure 1-2 Figure 1-3

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9

Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-1]

Table 1-1 Table 1-2 Table 1-3

Table 2-1 Table 2-2 Table 2-2 Game Overview......... Seas ceceeeee 12 Voltage-Selection Plug and Fuse Locations sect e eee e eee ees 14 Switch Locations ................... Settee oS

Screen 1: Operator Information Display ..................- 2-3 Screen 2: Alpha Processor Display. 2-4 Screen 3: Scaling Test Display . . . . CEE e eee een sees 2-5 Screen 4: Bipolar Offset Test Display. fig G4 dampen e nee sees 25 Screen 5: Crosshatch Pattern Display ............. cece eee 26 Screen 6: Color Intensity Test Display . 26 Screen 7: Color Intensity Test Display . . 27 Screen 8: Grid Pattern Display . . 2-7 Self-Test Trouble Analysis . 2-8

Control Panel Opening and Wire Colors ........ : 33 Roller Control Assembly Lubrication and Adjustment : : 3-4 Fluorescent Light and Speaker Board Removal, Display Access . 3-7 Utility Panel Wire Colors 2.0.0.0... 00 eee 3-9

Mlustrated Parts Lists

Cabinet-Mounted Assemblies ............... sine 42 Control Panel Assembly ........ bee eek : 4-0 Roller Control Assembly : eee gbaae 4-8 Fluorescent Tube and Speaker Board A sembly ant meee 4-10 Utility Panel Assembly... 2.00.00. 0.00.200055 emat as 4-ll Coinco Coin Door Assembly . 2.0... ee . 7 412 Coin Acceptor Coin Door Assembt! 415 Power Supply ‘mbly PCB Mounting Hardware . : Regulator/Audio 1] PCB Assembly Major Havoc PCB Assembly . .

List of Tables

Installation Specifications... ... bene eee 1-3 Switch Settings for Play Options ............ bee eee Lo Switch Settings for Price Options ........... see wae a

Gamma Microprocessor Faulty Component Locations fome 2 Alpha Microprocessor Faulty Component Locations .... . 2. 24 ROM Locations of Checksum Errors 2.

Page 8

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A WARNINGS A

Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game.

AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 9
WARNING Shock Hazard To avoid electrical shock, do not plug in the game until it has been inspected and properly set up for the line voltage in your area Do not touch internal parts of the display with your hands or metal objects!

Set Up

How to Use This Manual

This manual, written for game operators and service technicians, describes your new Atari game. Chapter 1 contains a game overview, game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains maintenance and repair procedures. Chapter 4 contains illustrated parts lists. Notes in this chapter refer you to other places in the manual for more detailed information. Schematic diagrams of the game circuitry are included as a supplement to this manual

Chapter 1

Page 10

set Up Major Havoc

Lower Speaker See Figure

High-Voltage PCB * Used with Atari Display See Display Manual & Figure 4-9 Fluorescent Light & Speaker Board Assy See Figure 4-4 Deflection PCB Used with Atari Display See Display Manual & Figure 4-9 Game Identification Label *

Video Display * See Figure 4-1 Access Panel

Control Panel Assy See Figure 4-2

Roller-Control Assembly See Figure 4-3

Regulator/Audio Il PCB Assy * See Figures 4-9 & 4-10

Game PCB x See Figures 4-9 & 4-11

Power On/Off Switch

Coin Door See Figures 4-6 & 4-7

Utility Panet See Figure 4-5

Power Supply *

See Figure 4-8 Shock Hazard

Do not plug in the game until it has been inspected. This game should only be connected to a grounded

3.wire outlet. you have only a 2-wire

outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded! %* Item with a serial number label

Figure 1-1 Game Overview

1-2

Page 11

Game Overview

You are Major Havoc, leader of a brave band of clones. All from one, one from all, fighting for humanity... . Eons ago the evil Vaxxian Empire overran the galaxy. Most of your ancestors were enslaved and taken to the Vaxxian homeworld, Only a few scientists escaped. The small band of scientists cloned you, Major Havoc, to fly your Catastrofighter through a wormhole in space, leading your clone army against the dreaded Vaxxian robots to free your people by destroying the enemy reactor.

New Features

High-Tech Game Cabinet. A new video arcade game cabinet design delivers high visibility and increased player attraction. Roller Control. The backlit roller control provides leftto-right and right-to-left directional movement. Multi-Layer Printed-Circuit Board. This state-of-theart design printed-circuit board (PCB) provides low system noise with high system reliability. Game Within a Game. Action occurs in the lower right corner of the TACTICAL SCAN. Breakout® can be played for a few seconds before the actual Major Havoc game play starts. Earn a bonus life here! Dual FIRE/JUMP Button. This dual-action button allows Major Havoc to jump in the maze sequence and to fire at enemy robots in the space wave. Add-A-Coin. This feature permits you to start a new Major Havoc game at the level where you last saw the TACTI- CAL SCAN in your previous game play. Secret Warp Code. The code feature rewards you for short game times as it advances to deep levels in game play. Use the roller control to dial in secret code numbers during the TACTICAL-SCAN wave. All major parts of the cabinet are illustrated in Figure 1-1.

Installation Requirements

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Specifications

Characteristic Requirement

Power Consumption 200 W ‘Temperature O° to +32°C (+32° to +100°F)

Humidity Not to exceed 95% relative

Line Voltage 100 to 240 VAC Width 64.1 em (25.25 in.) Depth 80.3 cm (31.6 in.) Height 170.8 cm (67.25 in.) Set Up

WARNING To avoid electrical shock, do not plug in the game until you have inspected the game and selected the appropriate line voltage plug. Do not touch internal parts of the display with your hands or with metal objects!
Page 12

Set Up

Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

  • Examine the exterior of the game cabinet for dents, chips, or broken parts,
  • Remove the screws from the rear access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows:

a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circuit board (PCB) and will void your warranty.

b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets.

c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square strain-relief plate in the wood slot at the bottom of the rear panel opening.

4A, 250V Fuse F3 20A,32V

Fuses F4-F6 4A, 250V d. Inspect the power supply. Make sure the fuse block cover is mounted in place. Check that the green ground wire is connected. e. Inspect other major subassemblies, such as the control panel, video display, EM] cage, and each PCB, Make sure they are mounted securely and that the green ground wires are connected.

Voltage-Plug Selection

and Fuses The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-2). This power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). See Figure 1-2 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the line voltage of your location. Now plug the game into a grounded 3-wire outlet.

VOLTAGE PLUGS

7A, 250V

J3

Fuse cover is shown in Figure 4-8

Figure 1-2 Voltage-Selection Plug and Fuse Locations

Page 13

Switch Locations

Power On/Off Switch

The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-1).

Utility Panel Switches

The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-1). The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates

Colm Volume Control Counter

Utility Self-Test Fenel Switch Set Up

the self-test mode. The auxiliary coin switch credits the game without activating a coin counter. See Figures 1-3 and 4-5 for details of these switches.

Option Switches Major Havoc has two option switches. Figure 1-3 shows the location of these dual-inline-package (DIP) switches on the game printed-circuit board (PCB). © Option switch SW1 at 13/148 controls game play options.

*® Option switch SW2 at 8S controls whether the coins are counted on | or 2 counters.

Auxiliary Coin Switch

Game PCB

Figure 1-3 Switch Locations

Page 14

Set Up Major Havoc

Selecting the Coin, Credit, and Game Options

Settings for option switches are listed in Tables 1-2 and 1-3. To verify other option selections, check the Operator In- Options preset at the factory are shown by the <4 symbol; formation Display that appears when you enter the Selfhowever, you may change settings according to your Test Mode. See Chapter 2 for details. needs,

Table 1-2 Switch Settings for Play Options

Settings of 8-Toggle Switch on Game PCB (SW1 at location 13/14S) 1 2 8

34567Option

Starting Lives Coin Setting 2 Coin Setting Free Play

Off Off

On On On Off

Off On

nase) Au ao

Game Difficulty

OnOnHard
OffOffMedium~<4

Off = On Easy

On Off Demo,

Bonus Life

OnOnBonus Life at 50,000 points
OffOffBonus Life at 100,000 points<¢
OffOnBonus Life at 200,000 points

On Off No Bonus Life

Attract Mode Sound On Silence Off Sound

Adaptive Difficulty* On No Off Yes<4

4 Manufacturer's recommended settings

  • Game difficulty increases with player skill level
Page 15

Set Up

Table 1-3 Switch Settings for Price Options

Settings of 8-Toggle Switch on Game PCB (SW2 at location 85)

12345678

Option

On Off

Off Off

On On

Off On

On Off, On On

Off. On

OffoffOff

Off On Off

Off On On

On Off Off

OnOffOn

Free Play 1 coin for 1 game (or 1 player) 1 coin for 2 games (or 2 player) 2 coins for 1 game (or | player

Right Coin Mechanism Right coin mech x 14 Right coin mech x 4 Right coin mech x 5 Right coin mech x 6

Left Coin Mechanism Left coin mech x 1-4 Left coin mech x 2

Bonus Coin Adder No Bonus coins For every 4 coins, game logic adds | coin For every 4 coins, game logic adds 2 coins For every 5 coins, game logic adds | coin For every 3 coins, game logic adds 1 coin

2-Coin Minimum*

“4 Manujacturer's recommended settings

  • This game has the ability to select the 2-coin-minimum capability, which requires the player to pay for two games in advance. If you want this ca Pability, short pin 6 on 13N to ground by soldering a short piece of wire from ground to this point
Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

Self Test

This game will test itself and provide data to show chat the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 18

Self Test

Self-Test Displays

The self-test switch and the auxiliary coin switch are located on the utility panel inside the coin door. The option switches are on the game printed-circuit board (see Figure 1-3) Enter the Self‘Test Mode by turning o7 the self-test switch. When the self-test switch is turned on during Attract, Ready-to-Play, or Game Play Modes, the game will go to the Operator Information Display (see Screen 1 of Self-Test Mode), which also contains the gamma microprocessor display (see Figure 2-1).

Screen 1: Operator Information Display This display shows the condition of the RAM and ROM for the gamma microprocessor. If there is a RAM or ROM failure, the display will identify the failed component and give its location. See Table 2-1 for the location of the failed gamma microprocessor component on the game PCB.

NOTE The following self-test displays are arranged in the sequence in which they occur after the selftest switch is set to the on position. Press the auxiliary coin switch to end each display and obtain the next display. If the self-test procedures are not performed in sequence, pressing the auxiliary coin switch will advance the game through the displays until the desired display is obtained. If the game is turned on with the self-test switch in the on position, the game will go directly to the Operator Information Display.

2-2 To return to the Attract Mode, turn off the self-test switch.

NOTE The game-reset circuitry must be operating or the game will lock up witha blank screen. Ifa locked condition occurs, turn the self-test switch offand turn the game off and back on. If the game does not restart after this action, troubleshooting of the game-reset circuitry may be necessary.

Table 2-1 Gamma Microprocessor

Faulty Component Locations

IdentifierMeaningLocation
RGamma RAM Error9PIQ
ce}Gamma ROM Error9S
PCustom IC Error13Q
EEEROM Error9QIR
Page 19

Major Havoc Self Test

Gamma Microprocessor Error See Table 2-1

Adaptive Ditticulty Game difficulty increases with 2-Coin-Minimum Option player skill level

Coin Mode ADAPT ON Attraction Sounds

2 COINS | PLAY

‘SW1 at 13/14S

FIRE/JUMP

sW2 at 88 ————_|

SHIELD Roller Control i

Eee IVES PER PLAYER

INUS EVERY 100000

No. of Lives per Play Comrnand Number to Gamma Microprocessor -———_——___... —™ 1 Bonus Life Earned Press SHIELD button to advance Every xx Points To reset high scores to default setthrough sounds or functions. : tings, hold down the right coin switch. Then, depress and release FIRE/JUMP button. You will hear a loud hissing sound. Wait for this sound to finish before exiting self test. Wait 10 seconds before turn- Press FIRE/JUMP button to activate the sound or function.

Reset High Scores ing the game off or leaving the Activating this function replaces Self-Test Mode. the game High-Score Table with the default set of high scores. To Left Coin Counter see the High-Score Table, enter = the Atta Mode and spin the Right Coin Counter

Roller Control to the left. Spin the ‘Sounds Off

Roller Control to the right to re- Scand velues enter the Attract Mode.

Figure 2-1 Screen 1: Operator Information Display

Page 20

Self Test

Screen 2: Alpha Microprocessor

Test Display The alpha microprocessor is responsible for much of the game play. Table 2-2 helps you determine the location of a faulty RAM on the game PCB.

Table 2-2. Alpha Microprocessor Faulty Component Locations

Iden-Hex LocationDefinitionPCB

tifier Location

A0000-07FFRAMError—WJ/K
B0800-O8FF &RAM1H

Swap 0200-0700

CcVector Gen.—LowRAM Error6M/N
DVector Gen.—High_- RAMError~—GL/M
ECommun. RAMErrorIF

ROM Checksums

See Table 2-3 to determine the ROM location of a checksum error in the alpha microprocessor.

RAM Locations See Table 2-2

Iways : Checksum Error EA one ROM Locations See Table 2-3

NOTE If the ROM checksum is correct, neither the self-test ROM identifier (a single character) nor the checksum (a double character) appears on. the screen.

Table 2-3. ROM Locations of Checksum Errors

Identifier PCB Location

SONY RNAUHOD IN/P IN/P 1Q 1Q IL* IM/N* 6K OK GH 6H OK/L"

“This ROM must be good for self test to function

Auxiliary Coin Counter

Left Coin Mechanism

Not Used

Not Used Not Used Right Coin Mechanism

Not Used

2-Coin-Minimum Option

Figure 2-2 Screen 2: Alpha Processor Display

Page 21

Screen 3: Scaling Test Display Ared outline frames the sides of the screen during this test. Inside this red outline a white box of decreasing size appears inside a white frame. The white box should shrink smoothly and disappear into the center indicator on the screen. Ifa sudden change in the size of the square occurs, an error may exist. This sequence will repeat indefinitely until you press the auxiliary coin switch. This pattern tests the binary and linear scaling circuitry.

Figure 2-3 Screen 3: Scaling Test Display Self Test

Screen 4: Bipolar Offset Test Display

NOTE This procedure should be performed only after the game has been on for at least 15 minutes to ensure that the game PCB is fully warmed up.

Press the auxiliary coin switch to obtain the Bipolar Offset Test (BIP) Display as shown in Figure 2-4. The lines in the center of the screen should cleanly overlap to form a single orange square. If you see red and green lines, adjust the X and Y bipolar offset potentiometers as described on the Linear Scaling schematic diagram in the Schematic Package Supplement (SP-252). These potentiometers are designated XBIP (R80) and YBIP (R81). The upper righthand corner of the orange square is the critical adjustment point.

Orange

Figure 2-4 Screen 4: Bipolar Offset Test Display

2-5

Page 22

Self Test

Screen 5: Crosshatch Pattern Display Press the auxiliary coin switch to obtain the Crosshatch Pattern Display as shown in Figure 2-5. Verify the following display characteristics: All four corners of the red outline must be off the screen, while all four corners of the white outline are completely visible. If not, adjust potentiometers XSIZE (R34), YSIZE (R48), XCENTER (R39), and YCENTER (R55) as described on the X and Y Output schematic diagram in the Schematic Package Supplement (SP-252). A white frame filled with a crosshatch pattern appears inside the red outline. The crosshatch corners are closed and the diagonal) lines form symmetrical diamond-shaped squares. These lines should be straight within ¥,-inch over their length (visually straight is satisfactory). If otherwise, adjust potentiometers XLINEARITY (R38) and YLINEARITY (R50) as described on the X and Y Output schematic diagram in the Schematic Package Supplement (SP-252). The crosshatch pattern is not tilted more than 4% -inch between corners. The pattern is a uniform white color. A line of alphanumeric characters stretches across the display.

Figure 2-5 Screen 5: Crosshatch Pattern Display

Screen 6: Color Intensity Test Display

Press the auxiliary coin switch to obtain the Color Intensity Test Display as shown in Figure 2-6. Verify the following display characteristics:

° Top row of color bars red, blue, and green. All three sets of color bars have six lines dim at the top and increasing in intensity at the bottom. Bars underneath the top row of color bars are white. Bars underneath the white color are yellow, light blue, and purple.

Figure 2-6 Screen 6: Color Intensity

Test Display

This test checks the seven screen colors and six intensities of each color. If the intensities do not progress from dim at the top of each color group to bright at the bottom, there isa problem in the Z-axis of the game PCB or in the video display. If the colors are not as described, there is a problem with the red, green, or blue output of the game PCB or with the video display circuitry. Use this pattern for tracking adjustments and for brightness adjustment. Refer to the Color X-Y Display Manual for the brightness adjustment procedure or to determine the possible cause of failure.

Page 23

Screen 7: Color Intensity Test Display Press the auxiliary coin switch to obtain the Color Intensity Test Display as shown in Figure 2-7. Sixteen intensities (15 visible and 1 with zero intensity) of each of 16 colors are displayed. One color is black, resulting in an empty column. Every location in the color RAM is used. Use this screen for vector generator and color RAM troubleshooting. Do not use it for adjustment or quality checking.

Figure 2-7 Screen 7: Color Intensity Test Display Self Test

Screen 8: Grid Pattern Display Press the auxiliary coin switch to obtain the Grid Pattern Display outlined in red as shown in Figure 2-8. Use this display to check for proper convergence and color purity. The horizontal lines may or may not touch the right side of the square,

Figure 2-8 Screen 8: Grid Pattern Display

2-7

Page 24

Self Test Major Havoc

Self-Test Trouble Analysis NOTE

Figure 2-9 providesa trouble analysis diagram to help you The game-reset circuitry must be operating or the use the SelfTest Mode to determine the probable cause of game will lock up with a blank screen. Ifa locked controuble and the possible remedies. dition ever occurs, turn the self-test switch off. Then turnthe game off and back on. If the game does not restart after this action, troubleshooting of the game reset circuitry may be necessary.

xp = microprocessor STEP 1

Turn on game. (Selt-test switch is off.) Gamma xp is bad and unable to respond. Gamma xp must be checked out. Go to START. Roller control

flashes.

Attract Mode is OK.

STEP 2 Does screen flash “G" after 4or5 sec. Fatal gamma up error. Possible bad 1H/J (alpha zero page RAM). Replace & go to START. (Lack of flashing in STEP 1 indicates no gamma pp error.)

No fatal gamma up errors Screen is blank & no sounds audible.

Low tones = Replace 6K/L (Vector ROM). Shigh tones = Replace 6M/N (Vector RAM). Many tones (~ 75)= Replace 1u/K (Vector ROM). Screen is blank & sound is audible. Press auxiliary coin switch to advance to Operator Information Display.

Inspect Operator Information Display. R, 0, P, orE attop of screen. R = Replace 9P/Q (Gamma RAM). O = Replace 9S (Gamma ROM). P = Replace 13Q (Custom IC) E = Replace 9Q/R (EEROM).

to advance to Alpha xp Test Display.

See Table 2-2 for bad IC it A, B, C, or D appear

at top of screen. E will always appear; ignore E.

See Table 2-3 for bad ROMs if 3 digits appear

above the lines of 1's & 0's. Display does not match Fig. 2-2 Inspect Alpha Test Display.

Press auxiliary coin switch to advance to Scaling Test Display.

Slow shrinking square is not same as Fig. 2-3. Error has occurred in the Vector Generator Scaling circuit. Digital circuit problem possible, but not likely.

Figure 2-9 Self-Test Trouble Analysis Diagram

2-8

Page 25

Press auxiliary coin switch to advance to BIP Display.

Inspect BIP Display.

Press auxiliary coin switch to advance to Crosshatch Display.

Inspect Crosshatch Display.

Press auxiliary coin switch to advance to Color Intensity Display—Screen 1.

Inspect Color Display—1.

Press auxiliary coin switch to advance to Color Intensity Display—Screen 2.

Inspect Coior Display—2.

Press auxiliary coin switch to advance to Grid Pattern Display.

Inspect Grid Display. Is not as shown in Fig.2-4,

Is not as described in text describing Fig. 2-5.

Isnot an orange square.

Many repeating colors appear, or colors all are same.

Obvious color smearing or color changes ina single screen,

END OF SELF TEST

‘Turn off self-test switch to return to Attract Mode.

Attract Mode Blank Screen

Self Test

(Assumes red/white borders are same as Fig.2-4,) If multiple green vertical lines appear, adjust REO. If multiple green horizontal ft pear, adjust R81.

[fred outline Is VISIBLE at all 4 corners, or white outline is NOT VISIBLE: adjust R34, R39, R48, & R50. If crosshatch lines are not straight:

adjusth38 & R50. If pattern is not uniform in

color: see Display Manual for purity adjustment.

It colors are incorrect: possible color RAM e ror at 12J OF 12K (Do next test.), orred, green, or blue output error. If intensities are incorrect: see Display Manual for brightness adjustment.

If colors are incorrect here & in last test: check red, green, and blue output circuitry RAMs at 12J & 12K for possible errors.

See Display Manual for purity & convergence adjustments.

Game reset circultry (WATCHDOG) is not operating. (The program re-enters the Game Mode from Self-Test Mode by purposely failing to reset the WATCHDOG circuit, which THEN forces the RESET line down.)

Figure 2-9 Self-Test Trouble Analysis Diagram, continued

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27
WARNING To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

Maintenance

The maintenance procedures provided in this chapter are for those items which are subject to the most severe use. To assure the maximum trouble-free operation from this game, Atari recommends that periodic routine maintenance be performed on the game components described in the following procedures. How often routine maintenance is performed depends upon the game environment and frequency of play.

Chapter 3

Page 28

Maintenance

Cleaning Requirements

This game cabinet and the display shield may be cleaned with any non-abrasive household cleaner. A toothbrush may be used to remove any stubborn build-up of residue in the coin path, on the plastic roller, or drive and idler shafts of the roller control. Be sure to lubricate the shaft bearings after cleaning. Compressed air is also recommended for cleaning dust from the interior of the cabinet.

Opening the Control Panel

Perform the following procedure to open the control panel:

  • Unlock and open the coin door. Reach up through the coin-door opening to the top of the front panel and release the spring-draw latch (see Figure 3-1).
  • Close the coin door.
  • Lift the front of the control panel by exerting upward pressure on both sides, Slide it forward and tilt it toward you.
  • Hook the control panel over the front of the cabinet using the bracket that is part of the black aluminum conirol-panel cap (see Figure 3-1).
  • Disconnect the control harness before moving the control panel to a work surface.

Pushbutton Leaf Switches

  • With the control panel open, adjust the leaf switch contacts for a narrow gap. Don’t burnish the contacts. To clean them, use electrical contact cleaner. N To replace a leaf switch, remove the screw with a Phillips-head screwdriver.
  • To remove the switch pushbutton, turn the stamped. nut with a wrench ina counterclockwise direction, as seen from the inside of the control panel. The ring on. the outside of the control panel should not spin. 4, Reinstall the pushbutton switch. Reconnect the harness wires to the switch terminals as shown in Figure 3-1.

Removing the Roller-Control Assembly

Perform the following procedure to remove the roller control from the control panel:

  • Open the control panel as previously described in this chapter and disconnect the wires from the lamp socket. Disconnect the harness at the four-pin connector on the coupler PCB assembly.

3-2

  • Remove the nuts and carriage bolts that secure the roller-control assembly to the control panel (see Figure 3-1)

Roller-Control Maintenance

Routine preventive maintenance of the roller-control assembly consists primarily of lubricating the shaft bearings and checking the mounting screws and washers for proper tightness approximately every four months. The roller-control assembly consists ofa roller, a drive shaft, an idler shaft, upper and lower frames, and a coupler PCB assembly. Refer to Figure 3-2 for the location of the parts mentioned in the following procedures.

Routine Maintenance and Disassembly

  • Open the control panel and remove the roller-control assembly as previously described in this chapter.
  • Use a Phillips-head screwdriver to remove the panhead screws that secure the upper and lower frames (see Figure 3-2).
  • Carefully lift the upper frame straight up from the assembly.
CAUTION Be sure to keep the drive studs in the upper frame. They must be in place during reassembly or the roller will not function.

ES Remove the plastic roller.

  • Apply two drops ofa light machine oil, such as 3-In- One oil, to the inside of the four shaft bearings. Wipe off any excess oil from the shafts.
  • The contact area of the drive shaft may have dirt buildup from use. Remove the residue as previously described in this chapter under Cleaning Requirements.
  • Use the appropriate hex-head wrench to check the tightness of the socket-head screw that secures the encoding wheel to the drive shaft. Use a pin or small screwdriver to steady the shaft. Refer to Figure 3-2 for an illustration of the the shaft screw location.
  • Lift the idler shaft and bearings from the lower frame. Be careful not to lose the bearings.
  • Slide the bearings off each end of the idler shaft.
  • Wipe off any dirt build-up from the shaft with a soft clean cloth ll. Lift the drive shaft with bearings and encoding wheel from the lower frame. Be careful not to lose the end bearing.
Page 29

Major Havoc Maintenance

Harness Control Panel

FIRE/JUMP Switch Wire Colors: Rolier-Control Assy, Yellow & Black

SHIELD Switch Wire Colors: Green & Black

Carriage Bolts & Nuts Ground Wire: Green

Control-Panel Cap

Lamp Wire Colors: Gray & Orange

Figure 3-1 Control Panel Opening and Wire Colors

3-3

Page 30

Maintenance Major Havoc

Upper Frame

Screwdriver or Pin

Hole in Drive Shaft

Roller

Encoding Wheel

Socket-Head Screw

Ball Bearing ~,

( Optical Coupler

Drive Shaft

Coupler PCB

Allen Wrench

Slot for PCB

Lower Frame

Lamp Socket

Figure 3-2 Roller-Control Assembly Lubrication and Adjustment

Page 31
  • Remove the metal encoding wheel by loosening the socket-head screw with an Allen wrench. Be careful not to lose the two small washers and screw.
  • Gently slide the other bearing off the end of the drive shaft. 14, Wipe off any dirt build-up from the shaft with a soft clean cloth.
  • Reassemble the roller-control assembly as described in the following procedure.

Reassembling the Roller-Control Assembly Perform the following procedure to reassemble the roller control (see Figure 3-2):

  • Remount the bearings, encoding wheel, washers, and socket-head screw on the drive shaft. 2, Reinstall the drive shaft in the lower frame.
  • Refer to Figure 3-2 and tighten the encoding wheel by inserting a %-inch diameter pin or screwdriver through the hole in the shaft. Tighten the socket-head screw with an Allen wrench.

Remount the bearings on each end of the idler shaft. Reinstall the idler shaft in the lower frame. Reinstall the plastic roller in the lower frame. Reinstall the coupler PCB assembly in the lower frame. DP Dw wd

Position the upper frame over the lower frame so the four screw holes are aligned and the coupler PCB assembly is secured.

CAUTION Be sure to keep the drive studs in the upper frame. They must be in place during reassembly or the roller will not function.
  • Use a Phillips-head screwdriver to tighten the four screws securing the upper and lower frames to each other, Maintenance
  • Reinstall the roller-control assembly in the control panel using the nuts and carriage bolts.
  • Reconnect the control harness.
  • Reconnect the wires to the lamp socket.

Replacing the Coupler PCB Assembly

To replace the coupler PCB assembly after the rollercontrol assembly has been removed from the control panel and disassembled, perform the following procedure (see Figure 3-2):

  • Disconnect the four-pin connector and lift the coupler PCB assembly from its slot.
  • Toreinstall the coupler PCB assembly, place the PCB in the slot in the lower frame and reconnect the fourpin connector.
CAUTION When you reinstall the coupler PCB assembly, make sure that the metal encoding wheel is not bent or damaged. Be sure the encoding wheel turns freely between the two halves of the radial optical coupler.

Light and Speaker Board Assembly

Removing the Light and Speaker Board Assembly Perform the following procedure to remove the light and speaker board assembly from the game (see Figure 3-3):

  • Remove the screws from the rear access panel of the game cabinet with a Phillips-head screwdriver.

3-5

Page 32

Maintenance

a Disconnect the harnesses from the fluorescent light assembly and from the speakers. From the front of the cabinet, use an Allen wrench to remove the screws from the attraction shield upper retainer. Slide both the attraction shield and the semi-rigid film that is behind the shield up and out of the extruded metal speaker grilles.

NOTE Aplastic U-shaped molding is firmly fitted on each side of the attraction shield and on each side of the display shield. These moldings should stay on when you remove the shields.
  • Remove the H-shaped retainer between the attraction shield and the display shield.
  • Slide the display shield up and out of the extruded metal speaker grilles.
  • Carefully remove the display bezel.
  • Remove the screws securing the extruded metal speaker grilles to the cabinet walls on both sides of the video display.
  • Remove the screws securing the light-and-speakerboard cleat to the display shelf at the top of the display.
  • From the back of the cabinet, remove the screws securing the light and speaker board to the side cleats. ll. Pull the fluorescent light and speaker board assembly out of the front of the cabinet.

Speaker Replacement To replace either of the speakers attached to the light and speaker board, you must first remove the fluorescent light and speaker board assembly from the game cabinet (see Figure 3-3). Perform the following procedure to replace a speaker:

iN

a Remove the fluorescent light and speaker board assembly as previously described. With the fluorescent light and speaker board assembly out of the cabinet, disconnect the two snap-on connectors from each speaker. Remove the hardware securing each speaker to its mounting grille/bracket. Mount each new speaker to its mounting grille/bracket with the appropriate hardware. Reconnect the snap-on connectors to each speaker. The white wire connects to the positive (+) terminal on the left speaker. The brown wire goes on the negative (unmarked) terminal on the right speaker (see the wiring diagram in SP-252).

NOTE The positive terminal on the speaker is marked with either a plus sign ( +) ora painted red dot.

Reinstalling the Fluorescent Light and Speaker Board Assembly

  • Carefully slide the fluorescent light and speaker board assembly into the upper front of the cabinet.
  • Replace the screws securing the lightand-speaker-board cleat to the display shelf at the top of the display.
  • From the back of the cabinet, replace the screws securing the light and speaker board to the side cleats. 4, From the front of the cabinet, reinstall the extruded metal speaker grilles on both sides of the video display with the appropriate hardware.
  • Slide the bottom edge of the video-display bezel into the retaining slot at the bottom of the cabinet head. Position the remaining three sides of the bezel in place around the video display.
  • Replace the video display shield (with the plastic moldings attached) by sliding the bottom edge into the slots of the extruded metal speaker grilles on either side of the video display.
  • Slide the attraction panel (with the plastic moldings attached) and semi-rigid film into the speaker grilles in front of the fluorescent light and speaker board assembly.
  • Use an Allen wrench to replace the hardware that secures the attraction shield upper retainer to the cabinet.
  • From the back of the cabinet, reconnect the 3-pin connector to the fluorescent light harness and the 2-pin connector to each speaker.
  • Use a Phillips-head screwdriver to replace the hardware that secures the upper access panel to the cabinet.
CAUTION This speaker is held by wedge only at the top. When reinstalling, slide the top of the speaker into the wedge before centering it over the panel opening and replacing the screws.

Lower Speaker

Access to the lower speaker is from inside the back of the cabinet (see Figure 3-3). Disconnect the speaker harness and the two snap-on connectors. Remove the screws securing the speaker to the speaker panel. The lower speaker grille may be removed from the front of the cabinet only with a square-drive screwdriver. The grille should be considered permanently installed.

Page 33

Attraction Shield / Maintenance

Fluorescent Light & ‘Speaker Board Assy

oN ]

Mounting Bracket pa 1 | YS ‘Anode Cap

CRT Neck Connector

Lower Retainer

\ Lower Speaker

Display Shield \ Lower Speaker Grille

Molding Speaker Grille

Figure 3-3 Fluorescent Light and Speaker Board Removal, Display Access

Page 34

Maintenance

Removing the CRT Assembly

WARNINGS High Voltage This display contains high voltages capable of delivering lethal quantities of energy. To avoid

danger, do not attempt to service the display until you have observed all precautions necessary for working on high-voltage equipment. X-Radiation This display has been designed for minimum X-radiation hazard. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube assembly may implode if struck or dropped. Shattered glass may cause personal injury within a 6-foot radius. To reduce the risks of injury to people or of damage to the game components, we recommend that two people perform the following removal procedures.

Perform the following procedure to remove the cathoderay tube (CRT) assembly from the game (see Figure 3-3):

  • Remove the rear access panel from the cabinet.
  • Discharge the high-voltage from the CRT before proceeding. The video display contains a circuit for discharging the CRT high voltage to ground when power is removed. However, to make certain, always discharge the CRT as follows: a. Attach one end ofa large, well insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap.

3-8 c. Wait two minutes and repeat part b.

  • Disconnect the CRT neck-pin connector, anode lead, yoke connector, degaussing coil connector, and 1-pin DAG spring connector (see Figure 3-3).
  • Follow steps 1 through 8 under Removing the Light and Speaker Board Assembly.
CAUTION Be extremely careful when removing the cathode-ray tube mounting bolts because the cathode-ray tube assembly can fail. We recommend thata second person carefully hold the cathode-ray-tube neck while the mounting bolts are being removed.
  • Use a %4-inch combination wrench to remove the bolts and washers from the front of the display mounting bracket
  • Carefully lift the CRT assembly from the front of the cabinet. 7, Replace in reverse order.
NOTE Whenever the cathode-ray tube is replaced, readjust the brightness, purity, and convergence as described in the display manual.

Wiring the Utility Panel

Controls

Refer to Figure 3-4 for the proper wire connections when replacing the controls that are mounted on the utility panel.

Figure 3-4 Utility Panel Wire Colors will follow the above text. Be sure the warning is on the illus.

Page 35

Major Havoc Maintenance

Before removing or repairing the utilty panel, turn the game off. Players may receive an electrical shock ifthe utility panels not properly grounded! After servicing any parts on the panel, make sure that the ground wireis

After servicing any parts on the pan firmly attached to the back of the coin

counter.

Orange/White Blue

Right Coin Counter

Orange/White Violet Left Coin Counter Grounding Clip

A002465-01 < ON oe a eee Coin Counter : Ss 2 Orange Y : | White/Yellow

White/Red

176018-002 Screw

69-001 Self-Test Switch 75-9910W0 Stamped Nut

62-041 Auxiliary Coin Switch

Black Common Gray (Normally Open)

Figure 3-4 Utility Panel Wire Colors

Page 36

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 37

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number, In these parts lists, al! A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Page 38

Illustrated Parts Lists Major Havoc

006008-05 041249-01 Molding Upper Retainer ‘A200009-02 Atari Display Assy See the Display Manual 041255-01 and Figure 4-9 Attraction Shield

Fluorescent Tube & Speaker Board Assy See Figure 4-4 oases — > ™ ganeror H-Shaped Retainer Bezel

201018-01 CRT Bracket

041130-01 Left Speaker Grille ae

041250-01 Lower Retainer

148001-013 041254-01 Speater Display Shield

041333-01 Speaker Grille

041130-02 Right Speaker Grille

Coin Door See Fi 46847 ee Figures Utility Panel See Figure 4-5

038091-01 Coin Box \ 178034-024 178127-036 T-Molding T-Molding

Figure 4-1 Cabinet-Mounted Assemblies A041300-01 A

Page 39

Major Havoc Illustrated Parts Lists

A041309-01 Fan/Harness Assy 178034-024 T-Molding A041341-01 Fan Harness. A041301-01 171002-001 Cabinet Assy A041303-01 Fan Head Assy Delection PCB Assy See the Display Manual and Figure 4-9

041240-01 High-Voltage PCB Assy 041251-01 Access Panel See the Display Manual Ventilation Grille and Figure 4-9

Control Panel Assy See Figure 4.2 178013-001 a © A041336-01 Latch Main Harness Roller-Control Assembly | 041232-02 See Figure 4.3, Rear Door

A038881-01 Lock

Regulator/Audio PCB Assy i a Game PCB See Figure 4-10 ee See Figures 4-9 and 4-11

041253-01 Hinge

A041338-01 038870-01 Power On/Off Switch Coin Box Enclosure

‘A037453-01 i : 041251-01 P Moines. ! Ventilation Grille ower Cord Power Supply See Figure 4-8 nna1a701 Game Publications— "ome, " Power Harness See parts list on next page

Figure 4-1 Cabinet-Mounted Assemblies, continued A041300-01 A

Page 40

Illustrated Parts Lists

Cabinet-Mounted Assemblies Parts List

Part No. Description

A037453-01Strain-Relief Power Cord(U.S. and Canada)

‘A038881-01 Lock (for rear door panel of pedestal) Acceptable substitute is part no. A038881-03

A041309-01 Fan and Harness Assembly—consists of A041341-01 Fan Harness 85-22F805 #8-32 x 0.3lnch Cross-Recessed Type F Screw (not shown) 171002-001 110 V Exhaust Fan

A041336-01 Main Harness A04133701 Power Harness A040699-01 Power On/Off Switch, Harness, and Mounting Plate Assembly A041301-01 Cabinet Assembly—consists of A041302-01 Body Assembly A041303-01 Head Assembly A200009-02 ATARI 19-Inch Color X-Y Display Kit Assembly—consists of A201106-01 Cathode-Ray Tube Assembly (not shown) A201014-01 Deflection PCB Assembly A201012-01 High-Voltage PCB Assembly

The foliowing five items are technical information supplements to this game: SP-252 Major Havoc Schematic Package ST-252-01 Major Havoc Label with Self-Test Procedure and Option Switch Settings TM-239, ATARI 19-Inch and 25-Inch Color XY Display Manual TM-252 Major Havoc Operators Manual TM-248 Star Tech Journal Subscription Card

78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive ‘Tape, %4-Inch Wide x -Inch Thick (36 inches required; used along top and bottom edge of display shield) 006008-04 Display Shield Extruded Plastic Molding 006008-05, Attraction Glass Extruded Plastic Molding,

009992-01 On/Off Switch Cover (not shown)

034536-02¥-Inch Thick Foam Pad(located between the High-Voltage PCB and the cabinet wall, and between the

Regulator/Audio PCB and the cabinet wall—not shown

034536-031.12-Inch Thick Foam Pad(located between the Deflection PCB and the cabinet wall—not shown)

037243-01 Base Plate for Power Supply (not shown)

038091-01 Molded Coin Box 038870-01 Coin Box Enclosure 041130-01 Left Speaker Grille 041130-02 Right Speaker Grille 041232-02 Rear Door for Pedestal Assembly (does not include lock or hinges) 041240-01 Rear Access Panel for Head Assembly 041249-01 Attraction Shield Upper Retainer 041250-01 Display Shield Lower Retainer

041251-01 Ventilation Grille (one located in floor of head assembly; one located in lower rear body assembly) 041253-01 Hinge for Rear Door of Pedestal Assembly 041254.01 Display Shield 041255-01 Attraction Shield

bs ob (continued on next page)

Page 41

Illustrated Parts Lists

Cabinet-Mounted Assemblies Parts List, continued

Part No. Description

041256-1715 H-Shaped Retainer for Attraction Glass and Display Shield 041261-01 Video Display Bezel 041318-02 Semi-Rigid Attraction Film with Graphics (not shown) 041333-01 Speaker Grille

148001-013 © x 9-Inch Oval, 4-Ohm, 6-Ounce Shielded High-Fidelity Speaker (located above control panel) 178013-001 Spring-Draw Latch 178034-024 34-Inch Black Plastic FMolding (21 inches required on front of pedestal base; 168 inches required on the side panels of the head assembly; 104 inches required on the side panels of the body assembly; 94 inches required on the front panel of the body assembly) 178127-036 2 %-Inch Black Plastic Molding (68 inches required on the pedestal)

179125-001 Grounding Clip on Main Harness (not shown) 201018-01 19-Inch CRT Bracket

Page 42

Mustrated Parts Lists

§ g 2 be RS g 6 & Ss Sa ao og ge 25 82 =o Bs 25 = a z -o5 32 cote 2 ° 37 eo S20 $38 eo Zz $85 gc ne S$. 532 88 @3 SHS Za — @- 832 Eg fe

=3 k& Sa "e

Roller-Control Assembly See Figure 4-3

Figure 4-2 Control Panel Assembly A041310-01 A ee 177010-240 Locknut

75-5144B Bolt

041247-01 Control Pane! Cap Control Panel

A041311-01 Control Panel with Decal 041316-01

parts on the panel, make sure that Players may receive an electrical shock if this control panelis not properly grounded! After servicing any the grounding clip is secured to the metal tab onthe inside ofthe control

+

Page 43

Mlustrated Parts Lists

Control Panel Assembly Parts List

Part No. Description

A039421-02 Roller-Control Assembly, AO41311-01 Control Panel with Decal—consists of 041316-01 Control Panel 04131703 Decal (not shown)

A041338-01 Control Harness 72-5508 Y-Inch-20 x %-Inch Hex-Head Machine Screw 75-0458 %-Inch Split-Lock Washer 75-5144B #10-24 x 2.75-Inch Black Carriage Bolt

75-9910NO %-Inch-Il Stamped Nut 0A1247-01 Control Panel Cap 160013-001 Leaf Switch with Button Holder 177010-240 #10-24 Hex Locknut

178030-004 Red Pushbutton 178030-007 Yellow Pushbutton, 179125-001 Grounding Clip (Acceptable substitute is part no. 179074-010)

Page 44

Ilustrated Parts Lists

176010-106 —F Screw

039426-02 Roles ee

039424-01 Drive Shaft

035937-01 Ball Bearing

039425-01 Idler Shaft ©

039423-01 Lower Frame

179173-001 Lamp Socket 178116-005 Drive Stud

039422-01 Upper Frame

035938-01 al Encoding Wheel

139002-001 Optical Coupler

A035220-02 Coupler PCB Assy

75-044S Split-Lock Washer

th 12-0408 a Screw

75-0148 Flat Washer

Figure 4-3 Roller-Control Assembly A039421-02 A

Page 45

Roller-Control Assembly Ulustrated Parts Lists

Parts List

Part No. Description

A035220-02 Coupler PCB Assembly— includes 79-58356 4-Position Connector 035221-01 Printed-Circuit Board 110000-151 1502, +5%, 4 W Resistor (not shown) 139002-001 Radial Optical Coupler

70-1H161 14 V Wedge-Base Lamp 72-8406 #4-40 x %-Inch Hex Socket-Head Cap Screw 75-0148 #4 Plain Flat Washer 75-0448 #4 Spring Split-Lock Washer

035937-01 Ball Bearing—4 per assembly 035938-01 Etched Encoding Wheel 039422-01 Upper Frame 039423-01 Lower Frame

039424-01 Drive Shaft 039425-01 Idler Shaft 039426-02 Blue Translucent Roller 176010-106 #8 x 4-Inch Cross-Recessed Zinc-Plated Steel Pan-Head Screw

178116-005, #6 x 0.31-Inch Drive Stud 179173-001 Wedge-Base Lamp Socket

Page 46

Ilustrated Parts Lists Major Havoc

A041342-01 70-304 Speaker Harness Assy Fluorescent Tube 99-1109 Socket 041252-01 a Grile/Bracket 70085 001 041325-01 Tube Holder Ballast Shield

179035-001 Tube Holder, 99-11006 99-11003 A005493-01 Harness Assy

179125-001 Grounding Clip

148004-002 Speaker 037469-01 Bracket

79-561816P osizai-og Wire Nut Panel 142028-001 Transformer Wire Colors for Speaker

NOTE Brown To make sure that the fluorescent Orange tube starts, check that the ground wireis firmly attached to both the ballast transformer and steel tube bracket.

Figure 4-4 Fluorescent Light and Speaker Board Assembly A041320-01 A Parts List

Part No. Description

A005493-01 Fluorescent Tube Harness Assembly A037540-01 Ground Wire with Ring Lig (not shown) A041342-01 Speaker Harness Assembly 70-304 18-Inch, 15 W, Cool White Fluorescent Tube

79-S61816P Spring-Connector Wire Nut for 16- to 18- Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 99-11009 Starter Socket

037469-01 ‘Tube Bracket 041241-02 ‘Wood Mounting Panel 041252-01 Speaker Mounting Grille/Bracket 041325-01 Ballast Shield

142028-001 60 Hz, 118 V, Ballast Transformer 148004-002 5-Inch Diameter, 5 W, 4-Ohm Shielded Speaker 179035-001 ‘Tube Holder 179125-001 Grounding Clip (Acceptable substitute is part no. 179074-010)

4:10

Page 47

Major Havoc Illustrated Parts Lists

A039254-01 Harness Assembly

Before removing or repairing the util ty panel, turn the game off. Players may receive an electrical shock ifthe utility panelis not properly grounded! Alter servicing any parts on the panel, make sure that the ground wire is firmly attached to the bracket.

A002465-01 Coin Counter

176018-002 Screw

69-001 Self-Test Switch 75-9910WO Stamped Nut 119006-103 040412-01 Volume Control Bracket

62-041 Auxiliary Coin Switch

Figure 4-5 Utility Panel Assembly A040413-01 B Parts List

Part No. Description

A002465-01 Coin Counter A039254-01 Volume Control Harness Assembly (includes grounding clip) 62-041 SPDT Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Selffest Switch

040412-01 Component Panel 75-9910W0 1¥,,-32 Stamped Nut 119006-103 Dual Volume Control 176018-002 #6-32 x %-Inch Thread Forming Machine Screw

4-11

Page 48

Illustrated Parts Lists

99-10140 Panel Assembly 75-948S Locknut Z ° . 99-10116 ~ Lever 99-10152 WIhS= Right Coin Inlet oy IX 99-10147 Harness 171006-035 . Coin Mechanism *

75-9448 k Locknut S 99-10096 Fastener

99-10151 Left Coin Iniet

99-10080 Lamp Socket

99-10105, Bar

99-10104 . Bar Retainer

¢ N a 99-1042 thru 99-10045, 99-10154 pe . Coin Switch Assembly Bracket Assembly 4 99-10153 os i | . Coin Return Box \ g9-0150 Switch Cover 99-10068 SN a —~ Coin Chute NN , 4 65-4416 A Coin Switch ~

99-1075 thru 99-1078 KS Switch Wires 99-10008 Retainer 75.1412 Screw

Figure 4-6 Coinco Coin Door Assembly 171027-001 A

4-12

Page 49

72-HA1404C Screw

99-10139 Coin Door a

99-10148 Lock Assembly

9910146 a % &

72-JA1405B Screw

038091-01 Coin Box Ilustrated Parts Lists

99-10148 Lock Assembly

99-10142 Button Housing

99-10134 99.1019 Gover J~+————— Button Assembly 99-10118 Button

99-1015 Spring

99-10141 Coin Return Cover

99-10117 Coin Return Door

I<—— 99-10144 Channel Clip SB 99-15066 Screw

99-10149 Service Door

99-10143 Frame

Figure 4-6 Coinco Coin Door Assembly, continued 171027-001 A

Page 50

Mlustrated Parts Lists

Coinco Coin Door Assembly Parts List

Part No. Description

171006-035 Metal Coin Mechanism for U.S. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94068 #4-40 x #-Inch Truss-Head Screw

72-HA1404C #4-40 x 4-Inch Pan-Head Screw 72-JAI405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x %4-Inch Pan-Head Screw 75-9948, #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00

99-10045 Coin Switch Assembly for Australian $.20, Gerrnan 5 DM, British 10 P 99-10068 Coin Return Chute

99-10075Switch Wire(included in coin switch assembly 99-10043)
99-10076Switch Wire(included in coin switch assembly 99-10042)
9910077Switch Wire(included in coin switch assembly 99-10044)
99-10078Switch Wire(included in coin switch assembly 99-10045)

99-10080 Lamp Socket 99-10081 Key Holder

99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 9940115 Spring

99-10116 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-1018 Amber Coin Return Button 99-1019 Amber Coin Button for US. $.25

99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover

99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly 99-15066 Screw for Clamp

Page 51

Major Havoc Illustrated Parts Lists

170000-001 99-15026

Lamp Coin Inlet

179047-001 Lamp Base 99-15023 Base Plate

99-15056 Screw for Bezel 99-15025 NN Coin Inlet 99-15055 NN Relaining Screw NN 99-15040 Lever

: O— 99-15054 Pivot for Lever

75-914S Hex Nut

> 99-15028 Coin Return Box

99-15056 99-15027 Screw for Bezel Coin Return Box

99-15075, ‘Sw. Adjuster

99-15029 Bracket ~ 99-15060 Sw. Cover 99-15042 Switch.

75-3414S Screw

72-1414S Screw

Figure 4-7 Coin Acceptor Coin Door Assembly 171034-xxx A

Page 52

Mlustrated Parts Lists

99-15052 Spring for Button

99-15063 Screw

A037542-01 Harness—not shown |

wy

99-15067 Lock Assy.

038091-01 Coin Box

99-15073 Upper Door 99-15074 99-15070 Lower Door | Doors and Frame 99-15072 Door Frame

171034-001 — U.S. 25¢/25¢ Coin Door 171034-003 — Canadian 25¢/25¢ Coin Door 171034-005 — U.K. 10 P/50 P Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034-010 — German 2 DM/5 DM Coin Deor 171034-011 — German 1 DM/5 DM Coin Door 171034-015 — French 2 Frit Fr Coin Door

Figure 4-7 Coin Acceptor Coin Door Assembly, continued “Ee 99-15067 Lock Assy.

171034-xxx A 99-15038 Bezel for Button

99-15001 thru 99-15011 Return Button

99-15039 Bezel for Cover

99-15036 Cover

99-15071 Clamp

99-15066 Screw

Page 53

IMustrated Parts Lists

Coin Acceptor Coin Door Assembly Parts List

Part No. Description

A036597-01 Harness Assembly (Ireland-Built cabinet only) A037542-01 Harness Assembly 72-14148 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer

75-9148 #4-40 Steel Machine Hex Nut 75-3414S #4-40 x J-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25-cent Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate

99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate

99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20-cent Price Plate

99-1501] Coin Return Button with Italian 100 Lire Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box

99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038. Bezel for Coin Return Button

99-15039 Metal Bezel for Coin Return Button 99-15042 Coin Switch for U.S. 25 cents 99-15052 Spring for Coin Return Button 99-15055 Retaining Screw 99-15056 #4-40 x %o-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073, Upper Door

9915074 Lower Door 99-15075 Switch Adjuster 99-15083 Base Plate—includes 99-15040 lever 99-15054 Pivot for Lever

038091-01 Coin Box—not included in assembly (Acceptable substitute is part no. A037491-01) 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 171050-001 Dual Entry Face Plate 179047-001 Lamp Base

4-17

Page 54

Illustrated Parts Lists Major Havoc

A037395-01 Transtormer Assembly

Fuse block cover must be in place during game operation.

A021084-02 Voltage Plug

Capacitor

034544-01 Fuse Cover

79-4411001 78-70501SC Fuse Post Capacitor Bracket.

46-2017002 Fuse

A035891-02 Fuse Harness. 034482-02 A Chassis 46-301203

78-2708 Bushing

A034630-01 ruse Block Fiter Assembly

46-2014002 Fuses

79-15021001 A036690-01 Terminal Block Power Harness

3A-MDA3501 A034629-01 Rectifier AC Harness

Figure 4-8 Power Supply Assembly A037396-04 F

Page 55

Illustrated Parts Lists

Power Supply Assembly Parts List

DesignatorDescriptionPart No.
cl27,000 uF, 15 VDC Electrolytic Capacitor29-053
cl2-Inch Diameter Capacitor Mounting Bracket78-70501SC
CRI‘Type-MDA 3501 Bridge Rectifier3A-MDA3501
FlPanel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post79-4411001
FL7 A, 250 Y, 3AG Slow-Blow Glass CartridgeType Fuse46-2017002
FlLabel for Fuse Value037639-01
F24 A, 250 V, 3AG Slow-Blow Glass Cartridge‘Type Fuse(Acceptable substitute is46-2014002

part no. 46-2014001)

F320, 32 V, 3AG Slow-Blow Glass Cartridge‘Type Fuse46-301203
F4-F64A, 250 V, 3AG Slow-Blow Glass Cartridge‘Type Fuse(Acceptable substitute is46-2014002

part no. 46-2014001)

F2-F65-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover034544-01
F2-F6Label for Fuse Values037641-01
F42-Circuit Single-Row Terminal Block(located under F4)79-15021001
FLIRFI Filter Assembly (designation not marked)A034630-01
J2Power Harness AssemblyA035890-01
J3Voltage Plug for 120 V (105-135 VAC)(yellow wire color)A021084-02
J4aAC Harness AssemblyA034629-01
TI‘Transformer Assembly(designation covered)A037395-O1

Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x 55/64-Inch Ouiside 78-2708 Diameter x %-Inch Thick Power Supply Chassis Base 034482-02

Page 56

Illustrated Parts Lists

178149-607 NylonStandott 79.4948 &. ial 176015-112 1 Screw

[J 039585-01 oo Cage

A201024-01 Deflection PCB

034536-03 Foarn Pad 176015-112 Screw A

. 175004-708

Washer

039586-01 ae High-Voltage Shield

A201012-01 High-Voltage PCB

A035435-04 Regulator/Audio ll PCB See Figure 410

175004-708 Washer 1034536-02 Foam Pad

176015-112 A041347-21 Screw 2 Major Havoc Game PCB See Figure 4-11

Figure 4-9 PCB Mounting Hardware

4-20

Page 57

Mlustrated Parts Lists

Part No.

A035435-04 A201012-01 A201014-01 72-1604S

034536-02

034536-03 039585-01 039586-01

175004-708 176015-112 178149-607 PCB Mounting Hardware Parts List

Description

Regulator/Audio I PCB High-Voltage PCB Deflection PCB #6-32 x ‘%-Inch Cross-Recessed Pan-Head Screw

0.50-Inch Thick Foam Pad (located between Game PCB and cabinet wall; between Regulator/Audio PCB and cabinet wall) 1.12-Inch Thick Foam Pad (located between Deflection PCB and cabinet wall) HighVoltage Cage High-Voltage Shield

#8 Flat Fiber Washer #10 x %4-Inch Cross-Recessed Pan-Head Screw Nylon Standoff

4-21

Page 58

Illustrated Parts Lists Major Havoc

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the R33 specific written permission of Atan, Inc., Sunnyvale, CA purrs

This drawing is only conditionally issued, and neither re-f=)oa
Ceips nor possession tnereo! confers of trangte's arySoab se-
right in, or license to use, the subject matter of the draw-bedSa ta2)0
ing or any design or technical information shown thereon,CcCRE=

or any right to reproduce this drawing or any part there: 4 Sat) 4

of. Except for manufacture by vendors of Atari, Inc., and_2
for ine elute Uncen {he corporation's written license,CRSa

No right to reproduce this drawing is granted or the sub:

ject matter thereof unless by written agreement with orGaGo
written permission from the corporation.C20cet0

fr:

#3300-—

35V

oO _———_

OooSR410. 7!oO

ES

TIP32_TOAZ002ATDA2002A
EjazNsco2 Q5&=arr
cRa>ITcon
RSetC7 Gen© ceca
sznoCOGcs
0eafearsRee)4
BELRisin220 | R21 ew
0alcle4b
eaReo5470
—_—,«Sep eTOOR
|“eC4axe]

a0 th FRI

“Ty G10

4Ss3300uF+}—
-0220SBN"

RBO RI i/2w it cre oF iNacoz

04»3500.0
  • {_ 5 a sav"

Figure 4-10 Regulator/Audio II PCB Assembly A035435-04 D

4-22

Page 59

Regulator/Audio II PCB Assembly Illustrated Parts Lists

Parts List

DesignatorDescriptionPart No.

Capacitors

cl470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
c20.001 pF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
C30.1 uF, +80%, -20%, 50 V, Ceramic-Disc Capacitor122002-104
C4470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
cs0.01 EF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor(Acceptable100015-103,

substitute is part no. 122005-103)

C60.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
c70.001 wE, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
c80.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, C103300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
cul0.1 pF, +80%, -20%, 50 V, Ceramic-Disc Capacitor122002-104
C2470 wk, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C13,1000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108,
Ccl40.01 pF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor(Acceptable100015-103

substitute is part no. 122005-103)

cis0.22 wE, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C160.001 uF, 50 V, Ceramic-Disc Axial-Lead Capacitor122002-102
Cl70.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C18, C193300 pF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
C20, C210.1 pF, +80%, -20%, 50 V, Ceramic-Dise Capacitor122002-104

Diodes

CRIType-IN4002, | A, 100 V Silicon Rectifier Diode31-1N4002
CR4Type-IN4002, 1 A, 100 V Silicon Rectifier Diode31-IN4002
CR5-CR8Type-IN5401, 3 A, 100 V Silicon Rectifier Diode31-IN5401

Integrated Circuits

a‘Type-LM305, 5 V, Linear Voltage Regulator37-LM305
QsType-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002
Q7‘Type-IDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit137151-002

Resistors

RL2702, +5%, 4 W Resistor110000-271
R333.9, +5%, %4 W Resistor110000-330
R4100.2, +5%, 4 W Resistor110000-101
RS2.79, +5%, | W Resistor110009-027
RO3.9 kQ, 5%, 4 W Resistor110000-392
R77.5 kQ, +5%, 4 W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer119002-102
RO2200, +5%, ¥2 W Resistor110001-221
RIO10, +5%, 4 W Resistor110000-010
RI109, +5%, 4 W Resistor110000-100
RI21002, +5%, 4 W Resistor110000-101
R13, RI410 kQ, 45%, 4 W Resistor110000-103
RI91Q, +5%, % W Resistor110000-010
R20109, +5%, 4 W Resistor110000-100
R212200, +5%, %& W Resistor110001-221
R221002, +5%, 4 W Resistor110000-101

(continued on next page)

Page 60

Mlustrated Parts Major Havoc

Regulator/Audio II PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R240.1.9, +3%, 7 W Wirewound Resistor19-100P1015
R27, R281kQ, 45%, % W Resistor110000-102
R29, R30.109, +5%, % W Resistor110000-100
R32, R335.6kM, +5%, 4 W Resistor110000-562

Transistors

Q2TypeTIP32 PNP Power Transistor33-T1P32
Q3Type-2N3055 NPN Silicon Transistor34-2N3055,

Mechanical Parts

J66-Position Connector Receptacle79-58306
79-Position Connector Receptacle79-58308
J84-Position Connector Receptacle79-58354
Jo6-Position Connector Receptacle79-58306
jlo12-Position Connector Receptacle79-58346
Q2#6-32 x Y%-Inch Binder-Head Nylon Screw75-F60405
oe)#6-32 Nut/Washer Assembly75-99516
Q3Thermally Conductive Silicon Insulator78-16008
QsThermally Conductive Silicon Insulator78-16008
Q5, Q7#6 x #-Inch Cross-Recessed Pan-Head Zinc-Plated Steel Screw72-6606S,

Heat Sink 034531-01 Test Point (Acceptable substitute is part no. 179051-001) 179051-002

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

Illustrated Parts Lists

| 5

a8 9 s°

2|5wa-# odynis

| "| 5 yy = er Rv woot) woos

2 ) 2 nl _

3geFya120

—: oe |e Figs

Riga1312"10a

SPARE spare swe

Figure 4-11 Major Havoc PCB Assembly A041347-21 A

Page 63

Major Havoc Illustrated Parts Lists

cvs crear

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific writ ten permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, ancinetther receipt nor possession thereat con: fers or transfers any right in, or license to use, the subyect matter of the drawing or any design or technicalinformation shown thereon, ror any right to reproduce this drawing or any par thereof. Except for manufacture by vendors of Alar, Inc.. and for manufacture under the corporation’ witten license, no nights granted to reproduce this {drawing or the subject matter thereof, unless by wniten agreement wilh or watten permission from the corporation.

cS N ov

Page 64

Illustrated Parts Lists

Major Havoc PCB Assembly Parts List

DesignatorDescriptionPartNo.

Capacitors

Cl, C2100 uF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C3, C5,2.2 uF, 35 V, Tantalum Capacitor122000-225
C41 pF, 50 V, Aluminum Electrolytic Radial-Lead Capacitor123001-105
C6100 pF, 35 V, Aluminum Electrolytic Axial-Lead Capacitor24-350107
C7,C81 #E, 50 V, Aluminum Electrolytic Radial-Lead Capacitor123001-105,
co0.1 wE, 50 V Ceramic Capacitor122002-104
clo100 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002101
cll39 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
cl20.01 uF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C13-C180.1 pF, 50 V Ceramic Capacitor122002-104
cl9100 pF, 100 V Minimum, Dipped. Fixed Mica Capacitor128002-101
C2039 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
C21, C220.1 wE, 50 V Ceramic Capacitor122002-104
C230.01 pF, 100 V Polyester Radial-Lead Capacitor21101103
C240.022 uF, +10%, 50 V Polycarb Axial-Lead Capacitor122010-223
C25, C260.1 #F, 50 V Ceramic Capacitor122002-104
C2839 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
€30-C33,0.1 #F, 50 V Ceramic Capacitor122002-104
C349.01 #F, 100 V Polyester Radial-Lead Capacitor21-101103
C350.1 pE, 50 V Ceramic Capacitor122002-104
C360.022 pF, +10%, 50 V Polycarb Axial-Lead Capacitor122010-223
C370.1 wE, 50 V Ceramic Capacitor122002-104
3939 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
C410.1 wE, 50 V Ceramic Capacitor122002-104
C420.001 F, 100 V Polyester Radial-Lead Capacitor21-101102
C43-C480.1 wF, 50 V Ceramic Capacitor122002-104
c490.01 uF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C500.1 2B, 50 V Ceramic Capacitor122002-104
C5110 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-100
cs239 pE, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-390
C53-C55150 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-151
C560.1 wR, 50 V Ceramic Capacitor122002-104
cs7220 pF, 100 V Minimum, Dipped, Fixed Mica Capacitor128002-221
C580.01 pF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103,
C59-C610.1 pF, 50 V Ceramic Capacitor122002-104
C62, C630.22 wF, + 20%, 25 V, Ceramic Axial-Lead Capacitor122004-224
C64, C650.001 wF, 50 V Ceramic Capacitor122002-102
C660.22 mF, +20%, 25 V, Ceramic Axial-Lead Capacitor122004-224
C670.01 wF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C68-C700.001 nF, 50 V Ceramic Capacitor122002-102
C71-C740.0) #F, + 80% -20%, Ceramic Axial-Lead Capacitor122005-103,
C75-C810.1 #F, 50 V Ceramic Capacitor122002-104
C820.01 uF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C830.1 #F, 50 V Ceramic Capacitor122007:104

4-28 (continued on next page)

Page 65

Major Havoc PCB Assembly Parts List, continued Illustrated Parts Lists

DesignatorDescriptionPart No.
C84, C850.01 pF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C86-C88470 pF, 50 V Ceramic Capacitor120006-471
C89-C9OL0.1 #F, 50 V Ceramic Capacitor122002-104
C92, C930.01 pF, +80% -20%, Ceramic Axial-Lead Capacitor122005-103
C940.1 hE, 50 V Ceramic Capacitor122002-104
C100-C1750.1 #F, 50 V Ceramic Capacitor122002-104
178, C1790.1 #E, 50 V Ceramic Capacitor122002-104
C182-C1890.1 pF, 50 V Ceramic Capacitor122002-104
C190-C2050.1 pF, 50 V Ceramic Capacitor122002-104

Coils

Ll, L2100 pH, +10% Inductor141002-001
L3-L7830 mA, 0.29, +10%, 1.0 wH Peaking Coil Inductor141007-001

Diodes

CRIType-MV5053 Red Light Emitting Diode38-MV5053
CR2-CR5Type-IN100 20 mA, 80 V Diode31-IN100
CRG, CR7Type-IN914 10 mA, 100 V Switching Diode31-IN914
CR8.Type-IN100 20 mA, 80 V Diode311N100

Integrated Circuits

1HStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001, -120)

YKStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001, -120)

IL‘Type-27128 EPROM (200 ns) Integrated Circuit136025-104
IM/N‘Type-27128 EPROM (200 ns) Integrated Circuit136025-103
INPType-27128 EPROM (200 ns) Integrated Circuit(Acceptable substitute is part136025-102

number 136025-009)

1Q‘Type-27128 EPROM (200 ns) Integrated Circuit136025-101
IRType-74LS245 Integrated Circuit37-74LS245
2Type-74LS32 Integrated Circuit37-7ALS32
2LType-74LS04 Integrated Circuit37-7ALSO4
2MType-74LS253 Integrated Circuit37-7ALS253
2N‘Type-74LS74 Integrated Circuit3 7-74LS74
2PType-74LS244 Integrated Circuit37-TALS244
2QType-74LS244 Integrated Circuit37-7ALS244
2sType-6502B Integrated Circuit90-6012
3A, 4A‘Type-74802 Integrated Circuit37-74S02
3BType-74LSI91 Integrated Circuit37-74LSI91
3CType-74LS175 Integrated Circuit37-74LS175,
3D‘Type-74S04 Integrated Circuit37-74S04
3EType-74S74 Integrated Circuit37-74S 74
3F‘Type-74LS74 Integrated Circuit37-7ALS74
3H‘Type-74$32 Integrated Circuit37-74S32
3)‘Type-74S10 Integrated Circuit137236-001
3K‘Type-741SI57 Integrated Circuit37-74LS157
3LType-74LS32 Integrated Circuit37-74LS32

(continued on next page)

4-29

Page 66

Illustrated Parts Lists

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
3MType-74LS74 Integrated Circuit37-74LS74
3NType-74LS08 Integrated Circuit37-74LSO8
3PType-74874 Integrated Circuit37-74S74
3QType-74LS163 Integrated Circuit137274-001
3RType-741S245 Integrated Circuit37-74L8245,
38‘Type-74808 Integrated Circuit37-7408
4B‘Type-74S260 Integrated Circuit37-748260
4E‘Type-74LS163 Integrated Circuit137274-001
4F‘Type-74LS02 Integrated Circuit37-7ALSO2
4HType-74109 Integrated Circuit37-74109
4Type-74LS163 Integrated Circuit137274-001
4K‘Type-74LS163 Integrated Circuit137274-001
4L‘Type-74LS139 Integrated Circuit37-74LS139
4MType-74LS32 Integrated Circuit37-74L832
4N‘Type-74LS139 Integrated Circuit37-74LS139
4P‘Type-74LS04 Integrated Circuit37-74LS04
4QType-748393 Integrated Circuit37-74LS393
4RType-74LSI61 Integrated Circuit37-74LS161
4SType-748393 Integrated Circuit37-74LS393
5AType-74874 Integrated Circuit37-74874
5BType-74LS174 Integrated Circuit37-7ALSI7A
5C‘Type-74LS27 Integrated Circuit37-7ALS27
5DType-74LS74 Integrated Circuit37-7ALS74
5E‘Type-74LS32 Integrated Circuit37-TALS32
SFType-741S157 Integrated Circuit37-74LS157
5H‘Type-74LS157 Integrated Circuit37-74LS157
53‘Type-74LS164 Integrated Circuit37-7ALSIO4
5KType-74LS08 Integrated Circuit37741808
SLType-74LS157 Integrated Circuit37-74LS157
5MType-741S245 Integrated Circuit37-74LS8245,
5N‘Type-74LS138 Integrated Circuit137177-001
SP‘Type-74LS00 Integrated Circuit37-74LS00
5QType-74LSI61 Integrated Circuit37-74LSI61
5RType-74L8244 Integrated Circuit37-7ALS244
6AType-74886 Integrated Circuit137002-001
6BType-741S157 Integrated Circuit37-74LS8157
6cType-825129 Integrated Circuit136002-125
6DType-741S157 Integrated Circuit37-74LS157
OEType-741S157 Integrated Circuit37-74LS157
OHType-27128 EPROM (300 ns) Integrated Circuit136025-106
OK‘Type-27128 EPROM (300 ns) Integrated Circuit136025-107
6KIL‘Type-2764 EPROM Integrated Circuit(Acceptable substitute is part number136025-105,

136025-010)

OL/MStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001, -120)

OMINStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001, -120)

(continued on next page)

Page 67

Mlustrated Pacts Lists

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
6NIPType-74LS08 Integrated Circuit37-74LS08
6PIQ‘Type-748374 Integrated Circuit37-74LS374
6QIRType-748374 Integrated Circuit37-74LS374
7AType-74LS32 Integrated Circuit37-7ALS32
7BType-74S00 Integrated Circuit37-74S00
7CType-74LS138 Integrated Circuit137177001
7DType-74LS04 Integrated Circuit37-74LS04
7E‘Type-74LS175 Integrated Circuit37-7ALS175
JER‘Type-74LS279 Integrated Circuit137179-001
7H‘Type-7ALSI75 Integrated Circuit37-74LSI75
7Type-74LSi1 Integrated Circuit137149-001
7KType-74LS163 Integrated Circuit137274-001
7L‘Type-741820 Integrated Circuit37-74LS20
7M‘Type-74LS163 Integrated Circuit137274-001
7NType-74LS10 Integrated Circuit37-741510
7QType-74LS74 Integrated Circuit37-7ALS74
7RType-7418244 Integrated Circuit37-74LS244
BAType-74LS194 Integrated Circuit377418194
8BType-74LS194 Integrated Circuit37-74LS194
8cType-74L8194 integrated Circuit37-7ALS194
8DType-74Lsi94 Integrated Circuit37-74LS194
8EType-741S194 Integrated Circuit3 7-74LS194
8FType-74LS194 Integrated Circuit37-74LS194
8H‘Type-74LS157 Integrated Circuit37-74L8157
3)Type-74LS02 Integrated Circuit37-74LS02
8KType-74LS00 Integrated Circuit37-74LS00
8LType-74LS00 Integrated Circuit37-74LS00
8M‘Type-74LS273 Integrated Circuit37-74LS273
8NType-74LS04 Integrated Circuit37-74LS04
BPType-6502A Integrated Circuit90-6013
8QType- 74532 Integrated Circuit37-74LS32
8RType-7418139 Integrated Circuit377418139
9AType-74LS86 Integrated Circuit37-7ALS86
OBType-74LS86 Integrated Circuit37-74LS86
9cType-74LS86 Integrated Circuit3274586
9Cc/DType-74LS273 Integrated Circuit37-74LS273
OF/HType-74LS175 Integrated Circuit37-74LS175
OoType-74LS04 Integrated Circuit37-74LS04
9K‘Type-LM319 Integrated Circuit37-LM319
OL‘Type-74C04 Integrated Circuit137309-001
OPIQStatic RAM Integrated Circuit(Acceptable substitutes are part numbers137198-001

137211-001, -120)

9QIRType-2804 EPROM Integrated Circuit(Accepmable substitute is part number137329-450,

137329-300)

98Type-27128 EPROM (300 ns) Integrated Circuit136025-108
10KHType-74LS20 Integrated Circuit37-74L820

(continued on next page)

Page 68

Ilustrated Parts Lists Major Havoc

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
10)Type-74LS174 Integrated Circuit37-T4LS174
10K‘Type-74L874 Integrated Circuit37-74LS74
10LType-74LSI74 Integrated Circuit37-74LS174
10MType-74LS244 Integrated Circuit37-7418244
W/ZType-74LS174 Integrated Circuit37-74LS174
Wi2N‘Type-74198 Integrated Circuit137350-001
liA/BIntegrated Circuit137158-002
1cIntegrated Circuit137159-001
nbIntegrated Circuit137158-002
Wy‘Type-74LS153 Integrated Circuit37-74LS153
IKType-74LS153 Integrated Circuit37-7ALS153
MLType-74L830 Integrated Circuit37-74L830
1Q‘Type-74LS139 Integrated Circuit37-74L8139
HR, 12RType-74LS74 Integrated Circuit37-T4LS74
12A/BIntegrated Circuit137352-001
2c‘TypeTLO82 Integrated Circuit37TLO82CP
12DIntegrated Circuit137352-001
LyType-82825 Static RAM Integrated Circuit99-7005
12K‘Type-82825 Static RAM Integrated Circuit90-7005
12N‘Trackball Interface (LETA) Integrated Circuit137304-1001
12PType-7418245 Integrated Circuit37-T4LS245
12Q‘Type-74LS245 Integrated Circuit37-74LS245
BJ‘Type-74LS174 Integrated Circuit37-7ALSI74
BKType-7407 Integrated Circuit37-7407
13NType-74LS257 Integrated Circuit37-74LS257
13QCustom Integrated Circuit137324-1121
14BTypeTLO84 Integrated Circuit37347
14DType-TLO84 Integrated Circuit37347
14QType-LM324 Integrated Circuit37-LM324
14R/SType-LM324 Integrated Circuit37-LM324
VRIType-7815 Integrated Circuit37-7815
VR2Type-7915 Integrated Circuit37-7915,
VR3Type-7805 Integrated Circuit37-7805

Resistors

Rl1509, +5%, 4 W Resistor110000-151
R2, R310kQ, +5%, 4 W Resistor110000-103
R42200, £5%, % W Resistor110009-221
RS10 kQ, +5%, 4 W Resistor110000-103,
RO, R71kQ, +5%, % W Resistor110000-102
R8-R134702, +5%, ‘4 W Resistor110000-471
R14-R191kQ, +5%, 4 W Resistor110000-102
R205.6kO, +5%, 4 W Resistor110000-562
R2110 kQ, +5%, 4 W Resistor110000-103
R22-R241kQ, 45%, 4 W Resistor110000-102
R25, R2610k, +5%, 44 W Resistor110000-103,
R272209, +5%, % W Resistor110000-221

(continued on next page)

Page 69

Major Havoc PCB Assembly Parts List, continued Illustrated Parts Lists

DesignatorDescriptionPart No.
R281kQ, +5%, % W Resistor110000-102
R29, R308202, +5%, 4 W Resistor110000-821
R31, R3275kQ, +1%, % W Resistor110003-752
R3310 kQ, +5%, % W Resistor120000-103
R3410 kQ Horizontal Trimming Potentiometer119002-103
R35,10kQ, +5%, 4 W Resistor110000-103
R36,2.7kQ, +5%, %4 W Resistor110000-272
R37150 kQ, +5%, 4 W Resistor110000-154
R382 kQ Horizontal Trimming Potentiometer119002-202
R3910 kQ Horizontal Trimming Potentiometer119002-103
R402.5 mA, 8 V Varistor110004-001
R43,1000, +5%, % W Resistor110000-101
R44, R458209, +5%, % W Resistor110000-821
R46, R4775kQ, +1%, 4 W Resistor110003-752
R4810 kQ Horizontal Trimming Potentiometer119002-103
R4910kQ, +5%, % W Resistor110000-103
RSO2 kQ Horizontal Trimming Potentiometer119002-202
R5110kQ, +5%, 4 W Resistor110000-103
R52150kQ, +5%, 4 W Resistor0000-154
R532.7kQ, +5%, % W Resistor110000-272
R542.5 mA, 8 V Varistor110004-001
R5510 k@ Horizontal Trimming Potentiometer119002-103,
R581000, +5%, % W Resistor110000-101
R592.2k,45%, %& W Resistor110000-222
R6O470 kD, +5%, % W Resistor110000-474
ROL1k@, +5%, % W Resistor140000-102
R622.2kQ, +5%, % W Resistor110000-222
R63, R647.5kQ, +1%, % W Resistor110003-752
ROS.3.9kQ, +5%, 4 W Resistor110000-392
ROG15k, +5%, 4 W Resistor110000-153,
RO71kQ, +5%, % W Resistor110000-102
ROS10kQ, +5%, %4 W Resistor110000-103
ROO5602, +5%, % W Resistor110000-561
R70-R7275kQ, +1%, % W Resistor110003-752
R736.19 kQ, +5%, % W Resistor110000-622
R7475kQ, +1%, % W Resistor110003-752
R756.19 kQ, +5%, & W Resistor110000-622,
R761002, +5%, %& W Resistor110000-101
RI7130 kQ, +1%, % W Resistor110003-132
R78100 2, +5%, 4 W Resistor110600-101
R791.30 kQ, +1%, & W Resistor110003-132
R80, R81200 © Horizontal Trimming Potentiometer119002-201
R82-R89100 kQ, +5%, ‘4 W Resistor110000-104
R9012kQ, 5%, ‘4 W Resistor110000-122

(continued on next page)

Page 70

Illustrated Parts Lists

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
ROI2.2 kQ, +5%, v4 W Resistor110000-222
R924.7kQ, +5%, 4% W Resistor110000-472
R9310 kQ, 5%, 4 W Resistor110000-103
ROS2.2kQ, +5%, %& W Resistor110000-222
RIG22k, +5%, % W Resistor110000-223
RO?682, +5%, 4 W Resistor110000-680
R9B8-R1021kQ, 5%, 4 W Resistor110000-102
R1035.6kQ, +5%, 4 W Resistor110000-562
R104, R1051kQ, +5%, 4 W Resistor110000-102
R10610k, +5%, 4 W Resistor110000-103
R107, R1081002, +5%, % W Resistor110000-101
RIOD1kQ, +5%, % W Resistor110000-102
RIO5.6kQ, +5%, %& W Resistor110000-562
RUL10kQ, 45%,’ W Resistor110000-103
RU21kQ, +5%, % W Resistor110000-102
R13, RU41000, +5%, % W Resistor110000-101
RUS1kQ, 45%, & W Resistor116000-102,
RUG5.6kQ, 45%, 4 W Resistor110000-562
RU710kQ, +5%, 4 W Resistor110000-103
RUS1k, +5%, 4 W Resistor110000-102
R19, R120100 Q, +5%, & W Resistor110000-101
R121-R123,4702, +5%, 4 W Resistor110000-471
R124-R1261kQ, 45%, 4% W Resistor110000-102
R1I27-R13410kQ, +5%, 4 W Resistor110000-103
R1351kQ, +5%, % W Resistor110000-102
RBG39 kQ, 45%, & W Resistor110000-393
R13718k, +5%, 4 W Resistor110000-184
R13839kQ, +5%, 4 W Resistor110000393
RBO10 kQ, +5%, %& W Resistor110000-103
RI401kQ, +5%, 4 W Resistor110000-102
R14139 kQ, +5%, 4 W Resistor110000-393
R14218 kQ, +5%, 4 W Resistor110000-184
R14339 kQ, +5%, % W Resistor110000-393
R144, R14522 kQ, +5%, 4 W Resistor110000-223,
R146, R14710k, +5%, 4 W Resistor110000-103
R148, R1492.2 kQ, +5%, 4 W Resistor110000-222
RISO-RI533.3 kQ, +5%, % W Resistor110000-332
RIS4-R1571kQ, +5%, % W Resistor110000-102
RISS100 kQ, +5%, 4 W Resistor110000-104
R159, RIGO1kQ, +5%, “% W Resistor110000-102
RI71-R1771kQ, +5%, 4 W Resistor110000-102
RI78-R1851OkQ, +5%, 4 W Resistor110000-103

Sockets

1A24 Contaci, Medium-Insertion-Force IC Socket79-42C24
IF40 Contact, Medium-Insertion-Force IC Socket79-42C40

4-34 (continued on next page)

Page 71

Major Havoc Illustrated Parts Lists

Major Havoc PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
lH40 Contact, Medium-Insertion-Force IC Socket79-42C40
WK40 Contact, Medium-Insertion-Force IC Socket79-42C40
1L28 Contact, Medium-Insertion-Force IC Socket79-42C28
IM/IN28 Contact, Medium-Insertion-Force IC Socket79-42C28
IN/P28 Contact, Medium-Insertion-Force IC Socket79-42C28
1Q28 Contact, Medium-Insertion-Force IC Socket79-42C28
2824 Contact, Medium-Insertion-Force IC Socket79-42C24
6H28 Contact, Medium-Insertion-Force IC Socket79-42C28
OK28 Contact, Medium-Insertion-Force IC Socket79-42C28
OK/L28 Contact, Medium-Insertion-Force IC Socket79-42C28
6LIM40 Contact, Medium-Insertion-Force IC Socket79-42C40
6MIN40 Contact, Medium-insertion-Force IC Socket79-42C40
JE/F24 Contact, Medium-Insertion-Force IC Socket79-42C24
8P24 Contact, Medium-Insertion-Force IC Socket79-42C24
OPIQ40 Contact, Medium-Insertion-Force IC Socket79-42C40
9QR40 Contact, Medium-Insertion-Force IC Socket79-42C40
9S28 Contact, Medium-Insertion-Force IC Socket79-42C28
12N40 Contact, Medium-Insertion-Force IC Socket79-42C40
13Q24 Conuct, Medium-Insertion-Force IC Socket79-42C24

Switches

SW1, SW28-Toggle DIP Switch Integrated Circuit66-118PIT

Transistors

4-26‘Type-2N3904 Transistor34-2N3904
Q7, 08Type-2N3906 Transistor34-2N3906
Q9Type-2N3904 Transistor34-2N3904
Qo‘Type-2N3906 Transistor34-2N3906
QuType-2N3904 Transistor34-2N3904
Q12Type-2N3906 Transistor34-2N3906
QnType-2N3904 Transistor34-2N3904
Qi4Type-2N3906 Transistor34-2N3906
QisType-2N3904 Transistor34-2N3904
Q16-Q18Type-2N6044 Transistor34-2N6044

Miscellaneous

YI10-MHz Crystal90-123
Y212.096-MHz Crystal144000-001

‘Test Point (Acceptable substitute is part number 020670-001) 179051-002 Nylon Snap-In Fastener 81-4302

Page 72

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 73

TM-252 Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person,

Page: Comments:

Fill in if you wish a reply:

Name

Firm O Distributor

Address. O Operator City State. Zip. C Other

Area Code Phone

Page 74

First Fold

No postage necessary if mailed in the United States

USINESS REPLY MAIL

FIRST CLASS PERMIT NO. 173 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari Inc. Attn: Field Service/Coin-Op Division P.O. Box 906 Sunnyvale, California 95035

Second Fold

worg

Page 75

PES BGS RON BEI BS RN BE ER 28

LSE ES SS

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

lf the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. ; : : ‘ ‘ ‘ :

Page 76

C ATARI . TAR INC. a gyCAMORE pRIVE pO BOL, MILPITAS. CALIFORNIA 3" ail N9g1942:3100 * TELEX 35-7488 g5038