CATHODE RAY TOMES

Arabian Fight

Arabian Fight (World) (Sega, 1991) · Manual · 28 pages · 12 sections · original scan

Page 1

SEGA

AIRATBILAIN

FIGHT

4 Player Conversion Kit for Optional 19" or 25"

Monitor

Installation/Owners Manual

SEGA ENTERPRISES, INC.

999-0133

Page 2

ARABIAN FIGHT

by:

SEGA Enterprises, Inc. (U.S.A.) 2149 Paragon Drive San Jose. California 95131 Phone Number (408) 435-0201

  • FAX Number (408) 435-0294

A 4 Player Conversion Kit for

Upright Cabinet with Horizontal Monitor

NOTE: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PERSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTEFERENCE AT

HIS/HER OWN EXPENSE.

This SEGA product has the copy right notice as follows: SEGA 1992 This signifies that this product was disclosed in 1992 and is the property of SEGA Enterprises.

Page 3

Table of Contents

w Introduction ........sessesescesscesssecceeceecceeanessereeeeeeaoeesosoaes Handling and Installation Precautions Prevention of Counterfeiting and Conversion Labeling Precautions Concerning the Place of Installation System Requirements Tools Required Cabinet Preparation Kit Component Verification Installation Procedure Monitor Card License Seal Side Decal Marquee Control Panel Service Switch Assembly Harness Installation Cabinet 115 VAC System Grounding Cabinet System Checkout Printed Circuit Board Installation Logic Board and Complete System Checkout In Case of Difficulty Figure 1 Figure Figure Figure Figure Figure Figure

Test Mode Operation / Schematic Diagram WDD MANINYY YI UNUNUUNAWUWW

OCIAANDNA WY

Introduction

SEGA ENTERPRISES. LTD., supported by its high electronic technology of Large Scale Integration, microprocessors, etc, and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S AND KIT INSTALLATION manual is intended to provide detailed comments together with all the necessary information covering the operation and installation of electronic assemblies, electromechanical assemblies, control assemblies, and spare or replacement parts for coin operated games. This manual is intended

Page 4

Introduction

SEGA ENTERPRISES. LTD., supported by its high electronic technology of Large Scale Integration, microprocessors, etc, and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER'S AND KIT INSTALLATION manual is intended to provide detailed comments together with all the necessary information covering the operation and installation of electronic assemblies, electromechanical assemblies, control assemblies, and spare or replacement parts for coin operated games. This manual is intended for those who have knowledge of electricity and technical expertise in video games. Carefully read the enclosed information before starting the kit installation or troubleshooting procedures.

Handling and Installation Precautions

During Installation: 1, Be sure to remove power plug when working on the machine,

  • Be sure all connections and harness routing are secure.
  • Make sure all grounding connections are secure and properly affixed.
  • Do not use any fuse that does not meet the specified rating.

Prevention of Counterfeiting and Conversion Labeling

To prevent counterfeit and unauthorized conversions, the following label is supplied with all authorized SEGA kit products. ‘When handling such goods, be sure to locate and confirm the label. It is used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards. eee enn nee

AYVGFNE

ORIGINAL SEAL

ee ce sa ln a oe de wee eee eee

‘Reererenaes 1D em ed

Precautions Concerning the Place of Installation

The CONVERSION KIT is intended to be installed in an indoor game cabinet. Absolutely do not install it outdoors. When installed indoors the following places mentioned below should be avoided to ensure proper operation and usage: + Places subject to rain or water leakage, or condensation due to humidity « In the proximity of an indoor swimming pool and/or shower + Places subject to direct sunlight + Places subject to heat sources from heating units, hot air, etc.

  • Vicinity of highly flammable/volatile chemicals or hazardous materials + Sloped surfaces + Vicinity of anti-disaster facilities such as fire exits and fire extinguishers
  • Places subject to any type of violent impact « Dusty environment
Page 5

System Requirements

Power Supply:

RFI Line Filter:

Miscellaneous:

  • Input voltage 90 VAC to 13 5 VAC 60 Hz
  • +5 volts at 6 amps © +12 volts at 2 amps « Over-voltage protected at + 5.8 volts
  • Current limit set at 8 amps

1, If a switching power supply is used: + Current rating of 6 amps + Frequency attenuation of the following: 0.15 MHz 0.5 MHz 1.0 MHz 5.0 MHz 10.0 MHz 30.0 MHz

  • Ifa linear power supply is used: 40db 65db 65db SSdb S0db S0db

+ Current rating of 5 amps + Frequency attenuation of the following: 0.15 MHz 0.5 MHz 1.0 MHz 5.0 MHz 10.0 MHz 30.0 MHz

Line Fuse: Speaker: On/Off Switch: Isolation Transformer. Coin Door: Coin Meter: Power Cord: Color Monitor:

  • Video input 1 volt to 5 volt peak-to~peak positive polarity + Sync TTL negative polarity separate horizontal and vertical ¢ Horizontal frequency 15.7 50 KHz + Vertical frequency 60 Hz + Video bandwidth 12 MHz or greater 6db 19db 28db 42db 45db 50db

4 amp 120 VAC 8 ohms 10 watt 6 amp 120 VAC 115 VAC primary, 115 VAC secondary, 100 Watts Dual coin acceptors +5 Volt DC Three conductor with ground

+ Horizontal mounted + Recommended size 19 inch

Page 6

Tools Required

  • Drill + Hole cutter 1-3/16" « Phillips screw driver + Flat blade screw driver + Small flat blade screw driver
  • Scissors « Sand paper + Paint + Xacto knife
  • Wood patch

Cabinet Preparation

1, Remove old PCB, and all existing game harnesses. 2, Remove and disassemble the control panel.

  • Remove any side decals, monitor bezel, and marquee. 4, Using sandpaper and/or paint thinner, clean and smooth the cabinet for paint preparation. Use wood patch to fill any nicks or flaws in the cabinet.
  • Paint cabinet if required.
  • Wipe down and vacuum cabinet as necessary.
NOTE: You are building a new game, not just changing an old one. A nice, clean, and new looking conversion not only earns better, but lasts longer.
Page 7

Kit Component Verification Verify each component with the kit list provided to assure your kit is complete. If any part is missing after the inventory is taken, please contact your distributor and provide to them the following information:

  • Kit serial number
  • Part number and description of missing item/s 3, Date received

Kit List

Part NumberQuantityDescription
0002-00002#6 x 3/8 P/H Phil Tek
0002-00014#6 x 3/4 P/H Phil "AB" SMS
0312-002416#10-24 x 1 3/4 Carr/Bolt Black
0502-002416#10-24 Hexnut
0612-002416#10 Split Lock Washer
0692-002416#10 Flat Washer 1/2 OD
2112-00002Wire Nut #18
999-00871Monitor Card
999-01331Owners Manual, Arabian Fight
421-5801-1391License Seal
999-01272Side Decal
999-00861Control Panel Overlay
999-01291Marquee, Arabian Fight
999-01301Label Sheet (See List)
  • Test, Service, Volume Sticker
  • Play Instructions
  • Action Button Labels
  • Start Button Labels
999-00471FCC Plate
4750-00491Volume Control 100 Ohm 10 Watt
5090-50282PB Spst Switch Momentary
999-01224Joy Stick, 8 Way
999-00634Pushbutton, Microswitch (White)
999-01234Pushbutton, Microswitch (Red)
999-01244Pushbutton, Microswitch (Yellow)
JAM-00001Jamma Harness
999-00941Y/O Harness
KRO-17211Service Switch Bracket
833-8646-041Game PCB, System 32 Arabian Fight
Page 8

Installation Procedure

Monitor Card 1

License Seal 2.

Side Decal 3.

Marquee 4.

Control Panel 5.

6.

7.

. 8.

9.

10.

1. Locate the MONITOR CARD and measure the size of existing monitor card or the required size to fit (refer to the reverse side of the monitor card for 19” or 25" monitor size option). Cut the cardboard monitor card to size. (see figure 1) Install Play Instruction Labels horizontally accross the bottom of the Card.

Locate the LICENSE SEAL and place seal as shown in figure 1. Install Monitor Card on game cabinet. Note: Verify that the License Seal will be visible when the Monitor Card is installed on game cabinet.

Locate the SIDE DECALS and install on the left and right side panels of the cabinet (see figure 1). Note: A mixture of slightly soapy water can be used on the cabinet to position the Decal as desired. A squeegee may be used to remove any wrinkles in the Decal if soapy water is used.

Locate the MARQUEE SHEET and measure the size of existing Marquee or required size to fit and trim the Marquee Sheet to size. Install on cabinet. (see figure 1)

Locate the CONTROL PANEL OVERLAY and measure the size required and cut the control panel overlay to fit the existing control panel.

Define the location of the player push buttons and joystick(s) on the control panel. (see figure 2)

Cut holes in control panel to locate buttons and joystick(s). See template for button and joystick. (see figure 3)

Install the " PLAYER START" label or labels on the control panel overlay if applicable (see figure 2)

Drill the control panel for the player controls as shown in figure 2.

Install player control button labels on the control panel overlay (see figure 2)

Install player pushbution/s as required. (see figure 2)

NOTE: When buttons are securely placed and tightened in the control panel assembly, a small amount of clear RTV Silicone may be placed on two or three areas of the lock-nut to keep the switches from being unscrewed from the top

of the panel. (see figure 3)

Page 9

12.

Service Switch 13. Assembly

16.

17.

18.

19.

Harness Installation 20.

21,

22.

23.

24, Install player/s JOYSTICK/S as required. (see figure 2)

Locate SERVICE SWITCH BRACKET and install wo PUSH BUTTON SPST SWITCH MOMENTARY into bracket as shown in figure 4.

Locate VOLUME CONTROL 100 OHM 10 WATT and install into service switch bracket as shown in figure 4.

Locate TEST, SERVICE, VOLUME STICKER and place on the service switch bracket as shown in figure 4.

Locate KNOB 1/8" SHAFT and install on shaft of volume control 100 ohm 10 watt as shown in figure 4.

Install the Service Switch Assembly using 2 ea screws in the cabinet at either of the following locations (see figure 5): + On top of the steel enclosure for the Cash Box, inside the coin door.

  • Inside to the left of the coin door, mounted to the wood cabinet.

The Game PCB is Jamma compatible for player 1 and 2. Players 3 and 4 are connected to an I/O PCB attached to the main logic pcb. . Modification of an existing Jamma harness inside the game cabinet should not be necessary.

CAUTION SHOULD BE OBSERVED TO ASSURE THAT THE PIN OUTPUTS ARE CORRECT.

Connect the Player/s controls and buttons to the PCB..

Connect the T.V Monitor as shown in figure 6.

Connect the routed speaker wires to the speaker. Check the routing for security.

Connect the SERVICE SWITCH ASSEMBLY as follows: (see figure 4.)

FOR REMOTE VOLUME CONTROL OPERATION PERFORM THE FOLLOWING STEPS: a. Locate the 2 speaker wires which connect to pins L and 10 of the Jamma

connector, b. Connect the wire from Pin L of the Jamma connector and one side of the speaker to one side of the volume control. c. Connect the wire from Pin 10 of the Jamma connector to the other side of the

volume contol. d. Connect the other side of the speaker to the center terminal of the volume control. FOR REMOTE TEST OPERATION PERFORM THE FOLLOWING STEP: Connect the wire from Pin 15 of the Jamma hamess to one side of the Test pushbutton and connect ground to the other terminal of the pushbutton.

Page 10

FOR REMOTE SERVICE OPERATION PERFORM THE FOLLOWING STEP:

Cabinet 115 VAC System Grounding

Cabinet System Checkout 24,

26.

27.

28.

WARNING:

PCB Installation

Logic Board and Complete System Checkout 29,

30.

31, Connect the wire from Pin R of the Jamma harness to one side of the Service pushbutton and then connect ground to the other terminal of the pushbution.

Locate the GROUND lead (green) of the 115 volt input power Line (see figure 7). This must be connected to all components of the game system. This is a safety requirement for the players protection. This AC GROUND must be of # 18 AWG wire or larger. (see figure 7 for the proper routing of the wire)

. Apply power to cabinet system and check for the following voltages. If any voltage is incorrect, remove power and correct problem before proceeding any further. a. + 5 Volts on pins 3,4,C, and D of the 56 pin PCB connector. b. + 12 Volts on pins 6 and F of the 56 pin PCB connector. c. No voltage present on any other pins of the 56 pin PCB connector.

Check that the monitor has power. This can be accomplished by observing the glow of the filament inside the neck of the picture tube.

Check that the Marquee lamp has power.

Check that the system ON/OFF switch functions properly.

PROCEED ONLY IF THE ABOVE CHECKS ARE CORRECT

Install the logic PCB inside the cabinet (see figure 5). Use wood screws to secure the PCB through its' mounting feet

Locate the Switch Setting Sheet for factory recommendations. Setting options are adjustable in the Test Mode.

Connect the 56 pin Jamma connector to the PCB.

NOTE: The proper orientation of the connector (see figure 8). If not connected

32. properly, the system will not function and damage can occur to the PCB.

Apply power to the system and observe that the logic PCB functions. If a video picture is not present proceed to "IN CASE OF DIFFICULTY" portion of this manual. When corrected, return to this point and continue.

Page 11

33.

34,

35. Press the TEST BUTTON to enter the test menu. Individual tests can be entered by following the instructions on the Test screen,

Functionally test the game by: a. VERIFY that coin drops register proper credit/s and the COIN METER OPERATES b. VERIFY that the proper number of lives is given for each CREDIT c. VERIFY that all player controls operate properly

Locate the Kit SERIAL NUMBER STICKER and FCC PLATE. Install on the rear of the game cabinet. (see figure 1 )

Page 12

In Case of Difficulty No Raster/No Video ~Check A.C. line cord -Check line fuse -Check monitor brightness Check power switch and/or interlock switch -Check all solder connections on line filter and transformer Check for proper orientation of the 56 pin PCB connector Raster/No Video -Check all PCB to monitor connections -Check power supply voltage on PCB No Video/ Game sounds can be heard -Check monitor brightness -Check all PCB to monitor connections Incorrect Colors -Monitor needs degaussing -Check for proper wiring between PCB and monitor -Check monitor adjustment and adjust if necessary Wavy Picture -Check monitor ground is properly connected to monitor -Be certain sync inputs are properly connected to monitor -Check horizontal hold adjustment Vertical Roll/Horizontal Tear -Check horizontal and/or vertical hold adjustments -Check for proper wiring of sync from PCB to monitor No Sound -Check volume control potentiometer adjustment -Check for + 12 volts on edge connector of PCB -Check wiring from PCB to speaker -Check speaker for low resistance between the "+ "and"-" tabs Bad Sound Check wiring to speaker for bad solder connections ~Check sound with another speaker No Switch Input Check ground connection to switch/es -Check wiring between PCB and switch/es for proper connection -Check switch/es with an ohm meter to verify proper operation Switch Operates Incorrect Function -Check wiring between PCB and switches for proper orientation Check wiring for shorts between switch inputs No Coin Meter ~Check wiring to coin meter Check that + 5 volts is on + side of meter Verify a+ 5 volt meter is used When coin switch is made and meter pulses, the screen blanks out and/or game resets -Verify that a meter with a diode is used -If no diode is built in meter a 1N4004 can be used across the meter. Cathode to "+" side of meter and anode to "-"side of meter.

li

Page 13

Figure 1

CONTROL PANEL TOP VIEW 1P START 2P START 3P START 4P START © © © o? O “=O OOO OOO JOYSTICK JOYSTICK. JOYSTICK

@ Figure 2

Page 14

FIGURE 3

SERVICESW TESTSW VOLUME CONT TO SPEAKER TO S6P 10

TO SPEAKER S6PL

TO S6P 15 TO S6PR

TO 56P A

VOL.CONT TEST SERVICE

STICKER FOR SWITCH BRACKET

ASSEMBLY AND WIRING ON SWITCH BRACKET

FIGURE 4

Page 15

FIGURE 6 g on re

FIGURE 5

Page 16

ISOLATION WIRING OF AC LINE TRANSFORMER GROUND

SYSTEM 18 MAIN GAME BOARD

S6PIN CONNECTOR (JAMMA) COMPONENT SIDE

TO SPEAKER BLACK j

BLACK TO CONTROL PANEL ORANGE TTT) TO PLAYER 3 AND PLAYER 4

TO POWER SUPPLY

FIGURE 8

Page 17

TEST MODE

The test operation of this game allows you to verify operation of the game memory, input, sound, CRT, and game assignments. The test mode also includes coin assignments, and bookkeeping functions. ,

Selection of Test Items:

1, Push the TEST SW to cause the following TEST ITEM MENU to. appear:

TEST MODE INDIVDUAL

MEMORY TEST INPUT TEST SOUND TEST CRT. TEST GAME ASSIGNMENTS COIN ASSIGNMENTS BOOKEEPING BACKUP DATA CLEAR ~ EXIT

SELECT BY SERVICE BUTTON PUSH TEST BUTTON

  • When you push the service switch, the arrow (+) will move to the next item on the menu.
  • Press the Test Button to perform the selected function.
Page 18

Memory Test. When this item is selected, a list of Integrated Circuits will appear. Each item will Gispley “Good” or “Bad” to indicate whether or noi the IC is functioning properly. If “Bad”

appears, it indicates a malfunctioning Ic.

MEMORY TEST

POND Ic¢9 GOOD IC8 GOOD C18 GOOD <RAM> 116 GOOD IC36 GOOD 1C37 GOOD 1061 GOOD 1C#2 GOOD ICE3 GOOD ICS4 GOOD Ices GOOD GOOD ices GOOD | GOOD I¢70 GOOD 1¢71 GOOD 1¢74 GOOD C75 GOOD

PUSH TEST BUTTON TO EXIT

Input Test. This test indicates the condition of each switch and potentiometer. To test a switch, operate it, When the switch is in good operating condition, the “Off” will change to “On”. If it does not change, it indicates a malfunctioning switch.

INPUT TEST

PLAYERiP4p
UeO#COf
DOWNOffOt
RIGHTCifot
LEFTOfflent
ATTACKOffOi
JumMPOffOn
STARTOffOf
CONOFCOf

SERVICE-O4 TEST-Of

PUSH TEST BUTTON TO EXIT

Page 19

Sound Test. The sound test indicates whether or not the sound in each category is working properly or not. Select the item using the Service Button and then push the Test Button.

MUSIC 0 EFFECT 0 VOKE 0

  • EXIT

SELECT BY SERVICE BUTTON PUSH TEST BUTTON

RGB Color Check. The CRT test allows you to adjust the color of the monitor. The color becomes brighter from left to right

C.R.T. TEST 1/2

BLUE

PUSH TEST BUTTON TO CONTINUE

Page 20

C.R.T. Test. View the image and make sure that ell corners are straight. If the corners are not straight, make the necessary adjustments.

Cincy tesi22 Titi Meee Poe Ii)

Wit TTT] CULE PUSH TEST BUTTON TO EXIT!

Game Assignments.

The monitor allows you to adjust game assignmenis as follows:

GAME ASSIGNMENTS GAME DIFFICULTY

EASY HARD

ZC

Initial Players 2 (1 to 4)

ADVERTISE SOUND aN MONITOR FLIP NORMAL CABINET TYPE 4P START BUTTON USE > EXIT SELECT BY SERVICE BUTTON PUSH TEST BUTTON

A. Game Difficulty: Values range from 1-16. The higher the number, the more difficult the game play. ,

B. Initial Players: Sets the number of players allotted. The same number applies to both cases of starting and continuing (Min. 1, to Max. 5, with the standard setting being 2).

Page 21

Advertise Sound: Allows you to tur the advertising sound on or off.

Monitor Flip: Should be set to normal.

Cabinet Type: Should be set to 4P.

Start Button: Should be set to Use.

Coin Assignments. The coin chute type is set to individual. The credit to start play is two credits. One coin per chute equals one credit per chute. Fifteen different types of coin credits can be selected. See the coin/chute serting matrix on page 15.

COIN ASSIGNMENTS

COIN CHUTE TYPE INDIVIDUAL

CREDITTOSTART 2 CREDITS

COIN/CREDIT SETTING #1 COIN CHUTE #1 1 COIN 1 CREDIT COIN CHUTE #2 1 COIN 1 CREDIT

MANUAL SETTING > EXIT

SELECT BY SERVICE BUTTON AND PUSH TEST BUTTON

Page 22

Manual Setting, The coin to credit, Bonus Adder information and coin chute multiplier are displayed. Select the item by using the Service Button and then push the Test Button to perform

the selected function.

COIN ASSIGNMENTS MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT BONUS ADDER NO BONUS ADDER

COIN CHUTE MULTIPLIER

CON 1 COIN COUNTS AS 1 COIN

123456789 123456789

CREDIT > EXIT SELECT BY SERVICE BUTTON AND PUSH TEST BUTTON

Page 23

AWid 33¥4 92# ONILLAS SLIGSYD 9] SNIOD S _. y2# ONILLSS

SLIGSYO | SNIOD + SLIGSYO €] SNIOO & SLIGSYO Z| SNIOO Z SLIGSHO €| SNIOO S SLIGSHO Z| SNIOO > 1IGSYO L |] SNIOO Z | 22# DNILLES LIGSYO L]SNIOO€ | 124 ONILLES SLIGSYD S$] SNIOO ¥ SLIGSHO €| SNIOD € SLIGAHD Z| SNIOOD Z LIGSHO | 61# ONILLAS | 1id3¥o F | SNIOO y | 81# ONILL3S| | Lida¥o F[SNIOO € | 21# ONILLSS| LIGSYO 4} NIOOL | St¥ ONILLES | 1ids¥o L[SNIOO 2 | Zi# ONILL3S| | SLi0s¥o 9] NOD} | ++# ONILL3S| SLIGSHOS| NIOO! | O+# DNILLSS| [siidsuoy| NiOOt | 67 ONILL3S| F 5 2 5 # $

Sliqauoe| NiOO+ [| 8#ONIL13 Siidauo2| NiooO}t [| 94 5DNILL3 Ligsyo bt] NiOO} | +#ONILLS (AdhL TYAGIAIGNI JLAHD NIOD) ONILLAS LIGAUD/NIOO

Page 24

MANUAL SETTINGS

TOOIN [1 CREDIT

4 COINS |1 CREDIT

NO BONUS ADDEF 2 COINS GIVE 1 EXTRA COIN

4 COINS GIVE 1 EXTRA COIN

TOOIN COUNTS AS 1 COIN

1 COIN COUNTS AS 9 COINS

1.COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS

r COIN TO CREDIT

BONUS ADDER

COIN CHUTE #1 MULTIPLIER

COIN CHUTE #2 MULTIPLIER

q

1 COIN COUNTS AS 9 COINS

Coin chute #3 and coin chute #4 multpliers are the same as for #1 and #2 above,

Page 25

Bookkeeping 1/2. The Coin Chutes #1 through #4 are displayed with the total number of coin drops recorded per chute. The total of all four chutes is recorded under Total Coin. Coin Credits are displayed and the number of times the service switch has been used to gain credits is also recorded. The total of both types of credits are recorded under Total Credit

Number of Games: displays the number of times the game has been played. Total Operating time is displayed in days, hours, minutes and seconds. The toval game playing time is displayed in alike fashion. Average game length , Longest game time, and Shortest game time are displayed in hours, minutes and seconds. The utilization factor is displayed as a percentage. To continue, push

the Test Button.

BOOKKEEPING 1.2 COIN CHUTE #1 COIN CHUTE #2 COIN CHUTE #3 COIN CHUTE #4 TOTAL COINS COIN CREDITS SERVICE CREDITS TOTAL CREDITS

NUMBER OF GAMES io} TOTAL OP. TIME Od Oh OmOs TOTAL GAME TIME 0d 0h Om0s AVERAGE GAME TIME Ooh Om Os LONGEST GAME TIME Oh Om 0sOm Os SHORTEST GAME TIME Oh UTILIZATION FACTOR 0.0%

PUSH TEST BUTTON TO CONTINUE

Page 26

Scoring information is displayed below. The averege score, highest score, and the lowest score ranges are also displayed. To exit, push the Test Button.

BOOKKEEPING 22

Time Histogram Om00s-Om2es Om30s-Omses 1m00s~1m2es 1m30s~1m5es 2m00s~2m29s 2m30s-2ms5os Bmd0s~3m2es 3m30s~3m52s 4m00s~4m2es 4m30s~4 5m00s~S: S OVER 10m00s 0

AVERAGE SCORE HIGHEST SCORE LOWEST SCORE 0 PUSH TEST BUTTON TO EXIT io}

ie) ie}

io} i)

If you wish to delete all backup bookkeeping data, simply select YES and push the Test Button.

Otherwise, select No and push the Service Button.

BACKUP DATA CLEAR

SELECT BY SERVICE BUTTON . AND PUSH TEST BUTTON

Page 27

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 28

co-reee-e7, SCO-3991-2 neeven

ee ee

s sit “ee f i Paria

ml sce-v99e-¥ Binvo

a 5.

7 A,

Ce

St NY8 , Sve ? ALATTACK D1 JUMP = CONTRO PANEL _. a0 Bae ve Turns

Se wait ye 3 71S Boy Ip aa wr

ARABIAN FIGHT SYS 32

perce) Bac sess mens One

TPePLAVER T(LP)