Tunnel Hunt
Tunnel Hunt (Atari, 1979) · Manual · 58 pages · 32 sections · original scan
SERVIGE WAR UAL
wt “hs my RS
Jif
- ~, 2,
= WD ES = N Ney;
centuri.. 384-10-0100.
TUNNEL HUNT
CENTURI, INC.
245 W. 74TH PLACE
HIALEAH, FLA, 33014
CUSTOMER SERVICE:
TEL. #(305) 558-5200 (IN FLORIDA)
TEL. #(800) 327-7710 (OUTSIDE FLORIDA)
TELEX: 803694 ANSB CENTURI CABLE: CENTURI
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
“TUNNEL HUNT"
TABLE OF CONTENTS
I. _INTRODUCTION: PAGE NO.
USER INFORMATION F.C.C
FRONT VIEW, TUNNEL HUNT, CABINET------------~--------------------- 3
FRONT VIEW OF CABINET, PARTS LIST------------~-------------------- 4
GAME PLAY----------------------------------------------------- 5,6,7
ATTRACT MODE---------------------------- pee eee 8
II. _OPERATION:
SELF TEST--------------------------------------------------- 9,10,11 CONTROLS--------~--~----~--------------------------+--+------------- 12
GAME INSTRUCTIONS AND POINT SCORING----------~-------------------- 13
OPTIONAL SWITCH SETTINGS-~----------------------------- ee-------- 14
INSTALLATION & ELECTRICAL REQUIREMENTS-----~--------------------- 15
ROUTINE MAINTENANCE & SERVICE------------------------------------ 16
III. _GAME PART DRAWINGS, PARTS LISTS & SCHEMATICS:
GIMBAL-TYPE JOYSTICK ASS'Y (UPPER) -------------------9----9------- 17 GIMBAL-~TYPE JOYSTICK ASS'Y (UNDERSIDE) -~------------------------- 18 GIMBAL-TYPE JOYSTICK ASS'Y, PARTS LIST ( # 50130094)------------- 19
FRONT PLATE EXPLODED VIEW:
FRONT PLATE EXPLODED VIEW, PARTS LIST-
COIN DOOR EXPLODED VIEW (MECHANICAL) --------
COIN DOOR EXPLODED VIEW, PARTS LIST (MECHANICAL) COIN DOOR EXPLODED VIEW (HARDWARE) -----~-------------------------
COIN DOOR EXPLODED VIEW, PARTS LIST (HARDWARE) ------ es 25
COIN SWITCH AND BULB REPLACEMENT-----------~-~------------------- 26
COIN SWITCH AND BULB REPLACEMENT, PARTS LIST~--------------------- 27
REMOVING COIN MECHANISM---
POWER SUPPLY, TUNNEL HUNT-
EXPLODED VIEW OF POWER SUPPLY ASS'Y-
EXPLODED VIEW OF POWER SUPPLY ASS'Y, PARTS LIST (# 50350007)----- 31 CONTROL PANEL----~----------------------------------------------- 32
COMPLETE GAME LESS/PKG. ASS'Y (384-01-0200) ----------------- --+--33
COMPLETE GAME LESS/PKG. ASS'Y, PARTS LIST (384-01-0200) ---------- 34
CABINET REAR VIEW----------------------- 33-55-9999 en 35
“TUNNEL HUNT"
TABLE OF CONTENTS
(CONT'D)
III. _GAME PART DRAWINGS, PARTS LISTS & SCHEMATICS: PAGE NO. C.P.U. BOARD ASS'Y, PARTS LIST (# 384-13-0200)--------- 36,37,38,39 REG/AUDIO P.C.B. ASS'Y, PARTS LIST (# 384-13-0100)-- WIRING DIAGRAM--------- eoen enn -----------------------
REGULATOR/AUDIO II P.C.B., SCHEMATIC (384-17-0200) -------------- P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET P.C.B. TUNNEL HUNT, SCHEMATIC (384-17-0300) SHEET
II.
USER INFORMATION - F.C.C,
WARNING
THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY, AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUC- TION MANUAL, MAY CAUSE INTERFERENCE TO RADIO COMMUNICATIONS. AS TEM- PORARILY PERMITTED BY REGULATION, IT HAS NOT BEEN TESTED FOR COMPLIANCE PURSUANT TO SUBPART J OF PART 15 OF F.C.C, RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST SUCH INTERFERENCE, OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE INTERFERENCE IN WHICH CASE, THE USER AT HIS OWN EXPENSE WILL BE REQUIRED TO TAKE WATEVER MEASURES MAY BE REQUIRED TO CORRECT THE INTERFERENCE.
INTRODUCTION
“TUNNEL HUNT” IS A MICROPROCESSOR BASED COIN-OPERATED ELECTRONIC GAME, THAT MAKES EXTENSIVE USE OF DIGITAL INTEGRATED CIRCUITRY AND TELEVISION MONITOR CONCEPTS. THIS MANUAL IS DESIGNED FOR THE USE OF MAINTENANCE TECHNICIANS WHO POSSESS A GENERAL WORKING KNOWLEDGE OF SOLID-STATE CIRCUITRY, AND VIDEO MONITOR THEORY. ANY INDIVIDUAL NOT KNOWLEDGEABLE IN THESE AREAS SHOULD NOT ATTEMPT REPAIR OF THE ELECTRONIC PORTIONS OF THE GAME, IN ADDITION TO THIS MANUAL AND TRAINING IN ELECTRONICS, TROUBLE- SHOOTING AND REPAIR WILL BE FACILITATED BY ACCESS TO GENERAL-TYPE HANDTOOLS, A MULTIMETER, A 50 OR 100 MHZ OSCILLOSCOPE AND A LOGIC PROBE WOULD BE HELPFUL. TECHNICAL ASSISTANCE IS AVAILABLE BY CALLING (305) 558-5200, -2° QUESTIONS OR COMMENTS CONCERNING “TUNNEL HUNT” OR ANY OF OUR GAMES ARE WELCOME AND SHOULD BE DIRECTED TO:
CENTURI, INC.
CUSTOMER SERVICE DEPARTAMENT
#800-327-7710 (OUTSIDE THE STATE OF FLA.) #305-556-5888 (IN FLORIDA) Soe
NOTES
NEVER REPLACE ANY COMPONENTS WITH ANYTHING OTHER THAN EXACT REPLACEMENT PARTS, NEVER REMOVE CIRCUIT BOARD CONNECTIONS WHILE POWER IS ON, DO NOT REPLACE THE FUSE WITH ANYTHING OTHER THAN THE PROPER VALUE, A BLOWN FUSE INDICATES AN OVERLOAD CONDITION WITHIN THE GAME, REPLACING THE FUSE WITH A HIGHER VALUE CAN CAUSE SEVERE DAMAGE TO INTERNAL COMPONENTS IF AN OVERLOAD OCCURS. ALWAYS CONSULT THE MANUAL BEFORE ATTEMPTING REPAIRS.
FRONT VIEW OF CABINET
“TUNNEL HUNT" CABINET FRONT VIEW
PARTS LIST
| ITEM: | CENTURI_P/N: | DESCRIPTION: |
| 1. | 384-06-0100 | SILK SCREENED MARQUEE PANEL |
| 2. | 384-04-2200 | VIEWING PANEL |
| 3. | 384-06-0200 | SILK SCREENED INSTRUCTION PANEL |
| 4. | 384-06-0300 | LEFT SIDE DECAL |
384-06-0400 RIGHT SIDE DECAL
| 5. | 384-03-0300 | SPEAKER GUARD SCREEN |
| 6. | 384-06-0500 | CONTROL PANEL OVERLAY |
| 7. | 360-14-0700 | COINCO COIN DOOR (MODIFIED) |
“TUNNEL HUNT"
GAME PLAY
This Mode is entered when the Flashing Start Button is pushed. The Start LED will stay on, and all sounds will be activated. You will be placed "out in space" and the Tunnel will appear in front of you. The speed will be minimum. Ships will appear from either down the Tunnel or will fly “over head" and past you. Occasionally a ship from behind will shoot a shot past you just before it appears. However, you cannot be shot from behind. A white cursor will appear in the center of the screen. By maneuvering down the Tunnel, the Ship can be made to align with this cursor. It may be shot down by firing the lasers while holding the Ship in this position. Lasers shots come from the lower left & right hand corners alternately on each push of the Fire Button and travel "down" the Tunnel. If a Ship is hit (or shot), it will explode into pieces and an explosion sound will start. It's score value will display as described in the scoring section, and the SCORE Display will be updated. 1 hit will be added to the Hits display.
The Game is divided into a mumber of difficulty levels. LEVEL 1. Up t 6 Hits: No ships shoot back. A delay appears between the start of Ships. Easy Tunnel to follow. LEVEL 2. Up to 12 Hits: Ships randomly shoot back. The new Ship delay still exists. Tunnel still easy. LEVEL 3. Up to 18 Hits: All ships shoot back. The new Ship delay still exists. Tunnel harder again. LEVEL 4. Up to 24 Hits: Same as Level 3 but the Tunnel is much harder to follow. LEVEL 5. Above 24 Hits: All Ships shoot back. As soon as one ship is shot, another appears with NO delay. Same Tunnel as Level 4.
Each time a Ship is hit, your speed increases a little. If you are shot or crash, your speed is reduced to half of what it was for the next life (or the minimum, whichever is greater).
NOTES ON ABOVE: -If a Ship's Shot is hit, the ship that shot it will immediatly reappear, regardless of the game level. -If a Player avoids ships by hitting the side of the Tunnel and allowing them "to go out of range" continuously,ships will shoot back regardless of level.
LASER
The Laser has a limited amount of continuous fire. Each shot "heats up" the Laser; NOT shotting allows it to cool, but at a slower rate. The temp. of the Laser may be seen on the LASER TEMP: Display near the bottom of the screen. A moving bar show the temp. at any time.
As the Laser gets hotter, the bar grows more to the right. If you OVERHEAT the Laser, it will not shoot untill it cools 50%, The Laser has 4 STATES:
SAFE: The bar display is green and the words "LASER TEMP" are displayed.
SHIELDS The Shields may be used to protect you from dying by either enemy shot or crashing. Shields are activated by pressing the shield Button, as long as shield energy exists. Each new life restores shield power to max. Shield energy is "used up" slowly whenever the Shields are activated. A large amount is used if the Shields are hit by an enemy ship or shell. Shields are displayed as a grip pattern across the entire screen. Normally they are blue, and get darker as the energy is used up. If they are hit, they turn red, then back to blue. Shield energy is displayed on a bar graph similar to the Laser Temp. display. As energy decrease, the bar shrinks to the left. The Shields have 3 Energy STATES: STATE 1. OK. The bar display is green and the words"SHIELD PWR" appear. STATE 2. LOW. The bar turns yellow and the word "LOW" alternates with SHIELD PWR. STATE 3. OUT. The bar flashes red/green and the word "OUT" alternates with SHIELD PWR. If the Shield Button is pressed during this state, a warning beep is heard.
HULL TEMP, To reduce the amount of time a Player may drag along the wall to slow his speed, a HULL TEMP. feature has been added. As you drag on the wall, your HULL TEMP increases. If it ever reaches maximum (indicated by a marker on the graph display), you die. The current temp. is indicated by a bar graph at the bottom of the screen. As the temp. increase, the bar grows left to right. There are 3 HULL STATES: STATE 1. OK. The bar graph display is green and the words “HULL TEMP." are displayed. STATE 2. CRITICAL. The bar graph display flashes RED/GREEN. The word "WARNING" alternates with HULL TEMP and a beep warning sounds. STATE 3. DEATH. If the graph reaches the max. mark, you die.
HIGH SCORE TABLE - END GAME
If a Player's score is one of the 5 best since power-up, he may enter
his initials into the table. When the Game ends, his score is cheched to see if it qualifies. If not, the Game goes directly to PHASE 2 of Attract. If it does qualify, then the Game enter initial entry mode. The message "GREAT SCORE/ENTER YOUR INITIALS” appears and a letter in a white box. By moving the control left & right, the letter in the box will sequence up & down through the alphabet. Pressing SHIELD will enter the initial, indicated by the box about the letter turning orange. Another letter in a white box appears next to the last. 3 letters may be entered this way. At the entry of the 3rd letter or after approx. 2 minutes of NO letter entry, the Game will return to PHASE 2 of Attract.
Manufactured Under License from ATARI, INC.
ATTRACT MODE
There are 2 Phases of Attract Mode:
1. Phase 1 is similar to Game Play. A straight only Tunnel is traveled and Ships continue to fly at you. Some may shoot. The Lasers will fire automatically and hit all Ships that come down the Tunnel. This Phase lasts 30 seconds.
MESSAGES:
- SCORE Message in lower right corner.
- BONUS for xxxx will display in lower center of the screen where xxxx = 30, 60, or 90,000.If Bonus is selected else no message will display.
- COIN? PLAY(s)? or FREE PLAY displays near the bottom of the screen.
- HITS with the number of hits from the last game will display at the bottom of the screen.
- © ATARI displays above the score. Some messages are determined by the CREDIT STATE of the machine in Attract Mode:
@ CREDITS:
- LIVES with the # of lives per Game display in the lower left corner.
- GAME OVER flashes lower center of the screen . 1/2 CREDIT:
- CREDIT with 1/2 displays where LIVES used to be and the color changes from blue to orange.
- INSERT COIN flashed where GAME OVER was and a beep sound starts. 1 CREDIT or more:
- CREDIT with credit amount under displays in the LIVES location. Color is orange.
- PUSH START flashes in the GAME OVER location.
The Second Phase is the high score table and title display. At power up, the hight score table will be initialized to various initials and scores from 5000 down to 1000. The name "TUNNEL HUNT" will appear onto the screen in large letters and pulsating colors. Phase 2 is approx. 30 seconds. Under the name will be a table of the top 5 scores since last reset or power up.
MESSAGES:
- SCORE - same as PHASE 1
- © ATARI - same as PHASE 1
- CREDIT/LIVES - same as PHASE 1 dad) GAME OVER/INSERT COIN/PUSH START - same as PHASE 1
- ALL other Phase 1 Messages do not show.
SELF TEST
Self Test is entered by switching the Self-Test switch on the Coin Door. All memory is cleared & the high score table will be RE INITIALIZED. Step I. 1.
NOTES: RAM TEST
The Games 2 testable 2114's are tested. ANY Ram error will abort the test, thus if the first Ram Tests bad, an error in the second Ram will not show.
If the test passes, RAM OK is displayed on screen. If a beep is heard (NOT a steady tone), a Ram error occured in the chip at F4. If 2 beeps are heard, then the chip at E4 is bad. If this chip is bad, the chip at F4 will not be tested. The 2 beeps will be one high freq., one low.
- This Test assumes POKEY sounds to be working.
- If the RAM test fails ALL other tests are invalid.
- If the RAM test fails, all screen info. is invalid.
Step II. ROM TEST (PROM TEST) This Test will check the program memory in 2K intervals:
1.
2.
The
NOTES: If all ROM/PROM's verify OK, the words ROM OK will appear on the screen next to the words RAM OK. If one or more bad ROM/PROM's are detected, the word ROM followed by ONE or more letters will appear on the screen. following table show which chip the error occured:
| LETTER | Ic # | ADDRESS | NOTES |
| A | L/M 1 | 5000-57FF | - |
| B | K1 | 5800-5FFF | 1 |
| c | gil | 6000-67FF | 2 |
| D | H/F 1 | 6800-6FFF | 1 |
| E | F/E 1 | 7000-77FF | 3 |
| F | Dil | 7800-7FFF | 1 |
- This chip must be good to complete tests.
- The tests will run with this chip bad. However, messages "ROM" & "RAM OK" may not appear correctly or may not appear at all.
- I£ this chip is bad, the test is valid only through Step 3 and may not continue.
Step III. COLOR BARS, CHARACTER PROM, TONE TEST 1. After the ROM test completes, a set of color Bars will display. Just bellow this will be a 2 line DISPLAY of characters. The Characters will be "HILIGHTED" by bands of color. A Tone will come on and will continue to sound until any switch is pressed.
- The Color Bars test, the Color Ram and the Square Generator circuit. There should be 7 evenly spaced Bars starting from the top of the screen down to the top of the Character Display lines (about 80% of the screen). They should extend from the left edge of the screen approx. 80% across to the right. To the right of these are 3 more squares in the upper right hand corner. Below these should be a black band. The colors are as follows:
i DK BLUE | LT GRAY
YELLOW
CYAN
GREEN
PURPLE
| RED
~s— Character Display
| RAM OK ROM OK
Fic. 1
- The Character display test allows checking of the contents of ALPHA/NUMERIC Prom and the Character "HILIGHT". The color behind the characters will vary depending on what state the game was in when self test was entered.
ENTRY TIME COLORS (left to right) Phase 1 Attract Black,Green,Yellow,Blue Phase 2 Attract Black,Green, Yellow,Green Entering Initials Black, Green, Yellow,Orange Game Play Black ,Green, Yellow,Green Game Play,Hull,Warning ON Black,Green,Yellow,Red Power Up Black,Green, Yellow,Black NOTES: 1. The last color in each list will also be the hilight color of the ROM OK, RAM OK messages.
- The Tone Test simply show that the sound output circuit was working. This Tone may be stopped by press any button.
Step IV. SWITCH TEST, POT TEST, COIN-OPTION DISPLAY (This Step runs simultaneously with Step 3)
- The switch test allows each control switch & coin switch to be tested. (If any ONE Switch is "stuck", the tone of Step 3 will not be heard). By pressing and releasing each switch, a beep is heard each time a transition takes place. If no beep is heard, the switch or its associated circuity is faulty.
- The Pots on the joystick may now be checked by moving the control and observing the screen. Two pairs of numbers appear just right of center in the band marked Step 4 Test area in Fig. 1. The pair to the left should change when the control is moved left/right. The other should change when the control is moved up/down.
- Although the right most digit of each pair makes little sense, it should change rapidly when the control is moved. It is also normal for this Digit to "flutter" when no motion is made. The left hand digit should change through at least 4 values as the control is moved from one extreme to the other.
- If these numbers do NOT change as described, or no Tones are heard, change the 40 Pin chip at location D 3/4.
- The Option Switch bank located at B4 is displayed as a Group of 1's and 0's. This is the Coin Option Switch Bank. Switch 1 is displayed to the right through switch 8 to the left. This test checks the chip located at 4B 3/4 (40 pin). If changing the state of one of the switches at B4 cause no change with it's corresponding 1 or 0 on the screen, change this chip.
ADDITIONAL FEATURES: To allow set-up of the color Monitor, 3 Additional STEPS are accessible. To enter the next Step and each Step thereafter, press BOTH START and SHIELD, then release. STEP Al through A3: -Color purity screens. A total color screen will display to allow cheching and correction of color purity. Step Al is all RED, A2 is all GREEN, and A3 is all BLUE. STEP A4:
-A cross hatch pattern is displayed to check and aid in convergence of the color Monitor.
-Pressing START and SHIELD again will return you to STEP 1 of SELF-TEST. -Return to PHASE 1 Attract may be accomplished at ANY time from Any test by switching off the SELF-TEST Switch.
CONTROLS
- Left/Right, Up/Down Joystick (2 pots)
- Fire Button (Switch)
- Shield Button (Switch w/lamp)
- Start Button
- Self test Switch
- Coin Switches (2 switches)
MONITOR 19" Color Monitor
SOUNDS
All sounds are generated by 2 POKEYS: Pokey 1
- Shot Sound
- Explosion Sound
- Scrape wall Sound
Pokey 2
- Hull Temp. warning Beep
- Shields out warning Beep
- Laser warning Beeps (3 stages)
- Bonus Life award Beep
- Flight "Hum"
- Self Test Tones
GAME INSTRUCTIONS
- Insert Coin(s). Push Start Button.
- Use Joystick to maneuver down tunnel.
- Acceleration is automatic. Hitting walls slows you down.
- Shoot down enemy craft and shells to avoid being hit (avoid overheating lasers).
- Use shields to prevent being hit. (There is a limited amount of shield power per life).
- Points are based on size of enemy and your speed (times color bonus multiplier). Smaller ships at high speed are worth more.
GAME POINT SCORING
The score of a hit Ship or Shell is based on 3 factors:
- Your speed down the Tube.
- The distance (size) of the enemy ship or shot.
- How long you "have been alive" this life (know as the color Bonus Multiplier). The length of life is indicated by the color of the Enemy Ship. If a shot is hit, it takes the multiplier of the last color ship seen.
When a Ship or Shell is hit, the message VALUE: XXXX will display on the top of the Status Indicator for approx. 4 seconds.
COLOR MULTIPLIER COLOR cyan blue green yellow white black MULTIPLIER 1 2 3 4 5 6
If a Bonus Option is selected and the Bonus Score (or 100K) is reached, 3 Beeps will be heard and the word "BONUS" will appear under the LIVES display for 4 seconds.
OPTIONAL SWITCH SETTING
The following Switches for the Game "TUNNEL HUNT" are found on the C.P.U. BOARD. The settings below are a guide in selecting optional game format.
BANK 1 (B3)
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | g NORM. |
| #_OF STARTING LIVES | off Off | 2 Lives |
off on * 3 Lives On off 4 Lives On on 5 Lives
| BONUS LEVEL | off off | No Bonus |
off On Bonus c 30K&100K On off * Bonus c 60K&100K on on Bonus c 90K&100K
| NOT USED | NOT USED | SW. 6,7,8, not used |
x
| FOREIGN LANGUAGE” | off (SW. 8, Bank 2 Off) | * ENGLISH |
Off (SW. 8, Bank 2 On) GERMAN On (SW. 8, Bank 2 Off) FRENCH On (SW. 8, Bank 2 On) SPANISH
BANK 2_(B4)
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
ak
| FOREIGN LANGUAGE | x | (see above) |
| COIN MODES | off off | Free Play |
Off On * 1 Coin, 1 Play on Off 1 Coin, 2 Plays On On 2 Coins, 2 Plays
RIGHT-MECH
| MULTIPLIER | Off Off | * Mech has value 1 |
off On Mech has value 5 On Off Mech has value 4 On On Mech has value 6
LEFT-MECH
| MULTIPLIER | oft | * Mech has value 1 |
on Mech has value 2
| BONUS ADDER | off off | * No Bonus Coins |
off On 4 Coins gives 1 extra On off 2 Coins gives 1 extra On On 5 Coins gives 2 extra
SswITcH 3, BANK 1 and SWITCH 8, Bank 2 work together.
*NORMAL SETTINGS
INSTALLATION
Your game was shipped from the factory in ready-to-play condition. A brief inspection is suggested before the machine is removed from the carton. If there is damage to the shipping carton, contact the freight carrier for claim purposes. External damage could indicate possible damage to the cabinet and/or electronics components.
After the carton has been satisfactorily inspected, remove the machine from the shipping carton.
Examine the interior of the game for disconnected wires, cables, or harnesses. Make sure the electronic devices are securely mounted in their sockets, etc. Record the game serial number, since it will be required for reference and servicing.
ELECTRICAL REQUIREMENTS
Unless otherwise specified, this game is set to operate at 110 Volts A.C. Power supply chasis schematic information and parts list are included in this manual.
ROUTINE MAINTENANCE & SERVICE
Beacause of the solid state electronic circuitry, this machine should require very little maintenance, and only occassional adjustments. However, it is necessary to take steps to insure this.
The volume control is located on the front side of the cabinet
and is accessible trough the coin door.
The video monitor has been properly adjusted before shipping. Occassionally minor adjustments are necessary. Technical information, along with schematics, can be found in this manual. Adjustment controls for the monitor are located on the rear of the monitor.
“DO NOT MAKE ANY ADJUSTMENTS ON THIS MACHINE WHILE THE POWER IS
ON"! This machine should only be adjusted by a "qualified" technician.
For Service Information, contact:
CENTURI, INC.
CUSTOMER SERVICE DEPARTAMENT
#800-327-7710 (Outside the State of Fla.) #305-556-5888 (In Florida)
POWER SUPPLY
The Computer Board in this game operates most efficiently and reliably when the power supply is set so the voltage on the Board is 5.0 Volts, to. Volts. To check this, place a meter across 5 Volts, and ground, at the edge connector. If necessary, adjust the screwdriver control on the power supply, so the meter reads between 4.9 and 5.1
volts.
UPPER JOYSTICK ASS’Y.
JOY STICK(UNDERSIDE)ASS'Y.
ITEM:
11.
12.
13.
14.
15.
16,
17.
18. 50130094
GIMBAL-TYPE JOYSTICK ASS'Y
CENTURI_P/N:
50130096
50130108
50130098
50130107
50130097
50130095
50130099
50130100
50130101
50130104
50130105
50130102
50130103
10080039
10120039
10190009
10140005
50130106 PARTS LIST
DESCRIPTION:
ASS'y PIVOT-SHAFT & HARNESS
ASS'y, POT & LINKAGE
ASSEMBLY, BELLOW, CENTERING
PLATE, MOUNTING
HOUSING, PIVOT BALL
PLATE, CONTROL PATTERN-SQUARE
CAP, BELLOW
GIMBAL, INNER
GIMBAL, OUTER
HANDLE, CONTROL RIGHT
HANDLE CONTROL, LEFT
BEZEL, HANDLE
SWITCH, CHERRY #P163-AWAA
SCREW, MACH, CAP, HEX SOCKET HD, #6-32 x 7/8" LG, STL
MACH SCREW, HEX HEAD, #10 - 32x2/2" LG, STL ZINC PLT.
WASHER, PLAIN, FLAT, #10, STL, ZINC PLT.
NUT, HEX, SELF-LOCKING, POLYMER, STL #10-32
PLATE, SLIDE OTY:
2800-0 FRONT PLATE EXPLODED VIEW 25¢ COIN
Description
25¢ Coin Acceptor #4-40 Self Locking Nut Coin Inlet Chute Assembly 4x 3/8 Screw Lamp Socket #47 Lamp (6.3 Volt) Fastener Inner Panel/Lever Assembly Coin Return Button Assembly Coin Return Button 25¢ Price Decal Reject Cover Button (25¢) #4 x 5/16 Pan Head Screw #10-24 Hex Nut (Mounting Hardware) #10-24 x 1-1/8 Carriage Bolt (Mounting Hardware) Index No. Description
Coin Inlet Housing Coin Return Cover Coin Return Door Frontplate Assembly, 3-1/8" x 9-1/4" Coin Return Chute Assembly Bar Keeper 4-40 x 3/4 Screw Switch & Wire Assembly Retainer Switch Wire-Silver Switch 6-32 x 3/16 Screw 12 Volt Crem Assembly Switch Cover
NO. CENTURI_ P/N: MANUFACTURING P/N:
| 1. | 50270144 | 5031-10 |
| 5. | 50270169 | 904717 |
| 6. | 50270170 | 904716 |
| 8. | 50270172 | 404464 |
| 10. | 50270145 | 904591 |
| 11. | 50270146 | 904703 |
| 12. | 50270147 | 904589-2 |
| 16. | 50270149 | 904588 |
| 17. | 50270157 | 904590 |
| 18. | 50270150 | 904599 |
| 19, | 50270173 | 404463 |
| 21. | 50270168 | 905115 |
| 25. | 50270141 | 900651 |
| 26. | 50270142 | 904710-1 |
| 27. | 50130061 | 904845 |
| 29. | 50270165 | 404354 |
| 30. | 50270164 | 904762 |
2800-0 FRONT PLATE EXPLODED VIEW
(FIGURE 5)
PARTS LIST
DESCRIPTION:
25¢ COIN ACCEPTOR
LAMP SOCKET
#47 LAMP (6.3 VOLT)
INNER PANEL/LEVER ASS'Y.
COIN RETURN BUTTON
25¢ PRICE DECAL
REJECT COVER BUTTON (25¢)
COIN INLET HOUSING
COIN RETURN BEZEL
COIN RETURN DOOR PRONTPLATE ASS'Y. (32/8"x9%")
BAR
RETAINER
SWITCH-WIRE, SILVER
SWITCH
12 VOLT C.R.E.M. ASS'Y.
SWITCH COVER
index No. Part No.
404429
400-8 904782 904706
904822 404352
904722 904762 100-6-3 404354
904936 100-4-12 404353
900651 2800 SERIES COIN DOOR EXPLODED VIEW 25¢ U.S. COIN
Description Inner Panel With Levers Sub-Assembly Nut Toggle Switch Test Switch Decal Custom Harness Assembly Insulation Coin Counter Assembly (6 Volt D.C.) Nut Wire Key Holder Switch Cover Screw C.R.E.M. Coil Assembly. 12 Volts D.C. Keeper Screw Coin Switch Assembly for U.S. 25¢ Coin Retainer 7 /
/ ee \ ==
Description
Silver Switch Wire — tor U.S. 25¢ Coin Switch Coin Chute Coin Return Box Switch and C.R.E.M. Coil Bracket Assembly 25¢ Acceptor Bar Screw Miniature Bayonet-Base Lamp Socket #47 Lamp (6.3 Volt) Coin Inlet Chute Sub-Assembly Right Half of Coin Inlet Chute “U"-Type Fastener Screw Slam Switch Assembly
12.
17.
18.
19.
20.
21.
22.
23.
25.
26.
27.
31. 2800 SERIES COIN DOOR EXPLODED VIEW
CENTURI_ P/N:
50270160
50130062
50270161
364-62-1000A
50270162
50270140
50270163
50270164
50270165
50270142
50130061
50270143
50270166
50270167
50270144
50270168
50270169
50270170
50270171
50130063 25¢ U.S. COIN
(FIGURE 6)
PARTS LIST
MANUFACTURING P/N:
404429
904782
904706
904822
404352
904722
904762
404354
904710-1
904845
904701
904598
404428
5301-10
905115
904717
904716
404418
904707 DESCRIPTION:
INNER PANEL w/LEVERS SUBASS'Y.
TOGGLE SWITCH
TEST SWITCH DECAL
CUSTOM HARNESS ASS'Y.
INSULATION
COIN COUNTER ASS'Y.
WIRE KEY HOLDER
SWITCH COVER
C.R.E.M. COIL ASS'Y. (12 VOLT D.C.)
SILVER SWITCH WIRE- FOR 25¢ U.S. COIN
SWITCH
COIN CHUTE
COIN RETURN BOX
SWITCH & C.R.E.M. COIL BRACKET ASS'Y.
25¢ ACCEPTOR
BAR
MINIATURE BAYONET-BASE LAMP SOCKET #47 LAMP (6.3 VOLTS) COIN INLET CHUTE-SUBASS'Y.
SLAM SWITCH ASSEMBLY
index No.
oO Taw Part No.
404341 404341-1 404348-1
904591 904703 904589-2
904707-1 2800 SERIES COIN DOOR EXPLODED VIEW
25¢ U.S. COIN
Description
Coin Door Only (2 Coin) Coin Door Only (3 Coin) Coin Return Button Assembly for U.S. 25¢ Coin Coin Return Button U.S. 25¢ Price Decal Coin Return Button Cover for U.S. 25¢ Coin Lock Assembly Index No.
aD Part No.
345-4-5 904588 325-4-4 904590 904599 904581
406-416 904734 404357 Description
Screw Coin Button Housing Screw Coin Return Bezel Coin Return Cover Coin Door Frame, 11-5/8” x 13-3/8" Mounts in a 10-3/8” x 12-3/16" Opening Hex Nut Carriage Bolt Locking Arm Assembly
No.
10.
11.
12,
15. 2800 SERIES COIN DOOR EXPLODED VIEW
CENTURI_ P/N:
50270152
50270158
50270145
50270146
50270147
50270148
50270149
50270157
50270150
50270151
50270159 25¢ U.S. COIN
(FIGURE 7)
PARTS LIST
MANUFACTURING P/N: DESCRIPTION:
404341
404348-1
904591
904703
904589-2
904707-1
904588
904590
904599
904581
404357 COIN DOOR ONLY(2 COIN)
COIN DOOR BUTTON ASS'Y. FOR U.S. 25¢ COIN
COIN RETURN BUTTON
U.S. 25¢ PRICE DECAL
COIN RETURN BUTTON COVER
LOCK ASSEMBLY w/KEYS
COIN BUTTON HOUSING (INLET HOUSING)
COIN RETURN BEZEL
COIN RETURN COVER
COIN DOOR FRAME (11 5/8"x13 3/8")
LOCKING ARM ASSEMBLY
UNSCREW AND FLIP OVER TO REMOVE
COIN SWITCH AND BULB REPLACEMENT.
COIN SWITCH AND BULB REPLACEMENT
PARTS LIST
| CENTURI P/N: | MANUFACTURING P/N: | DESCRIPTION: |
| 50270167 | 404428 | SWITCH & C.R.E.M. COIL |
BRACKET ASS'y
| 50270143 | 904701 | COIN CHUTE |
| 50270166 | 904598 | COIN RETURN BOX |
| 50270168 | 905115 | BAR |
| 50130061 | 904845 | SWITCH |
| 50270164 | 904762 | SWITCH COVER |
SPRING CLIR THEN LIFT AND REMOVE
‘moo anvo [arr | Assewmi¥ no HIALEAH, FLoRiDa same 2 P=REMOVING COINMECHANSM aka remon [ fe" Reel Bisfoa 1
TRANSFORMER
CAPACITOR
a
POWER SUPPLY, TUNNEL HUNT
<a
(Transtormer) (Capacitor 1 (20)
A_WARNING.4 Fuse cover must be (Volt. Plugs) in place during game operation. i (i) (Fuse Block Cvr.) (a) =) (Cap. Bracket) ' >
(Fuse Harness) @
(Fuse)
< aN (aver
(Bushing) [ I
(Fuse Block) (Filter Assy.)
(Fuses)
\ (Pwr. Harness)
(AC. Hamm.) (Term. Block)
(Rectifier)
Power Supply Assembly
ITEM:
1.
2.
3.
4.
5.
7.
8.
10.
il.
12.
13.
14,
15.
16.
17.
18.
19.
20. 50350007
POWER SUPPLY ASS'Y (EXPLODED VIEW)
PARTS LIST
CENTURI_ P/N: DESCRIPTION:
50060225 CAPACITOR
50270210 CAP. BRACKET
50270211 FUSE HARNESS
50230020 FUSE
50270216 BUSHING
50230060 FUSE BLOCK
50270217 LABEL
50270215 TERM. BLOCK
50290021 RECTIFIER
50270214 A.C. HARNESS
50270213 PWR. HARNESS
50230058 FUSES
50270212 FILTER ASS'Y
50270218 LABEL
50270208 CHASSIS
50230059 FUSE
50230061 FUSE POST
50270209 FUSE BLOCK CVR.
384-12-0700 VOLT. PLUGS 120V 384-12-0800 VOLT. PLUGS 100V 384-12-0900 VOLT. PLUGS 200V 384-12-1000 VOLT. PLUGS 220V 384-12-1100 VOLT. PLUGS 240V
50280089 TRANSFORMER
TTaNVd TONLNOO NOLING C7SHS
—S
NOLING LYVLS LL} |
NOLIAg aus
a iP "" COMPLETE GAME LESS PKS.
cl
- Ae}
ITEM:
9.
10,11,
12.
13.
14.
15.
16.
17.
18.
19. 384-01-0200
COMPLETE GAME LESS/PKG.
CENTURI P/N:
50130094
384-01-1600
360-14-0700
50350007
384-13-0100
384-13-0200
384-01-0900
50250024 50250026 ©
384-08-1300
361-14-0300A
384-06-0200
384-04-2200
384-06-0200
50200011
50130049
50130105
50130093
375-01-1700A PARTS LIST
DESCRIPTION:
JOYSTICK ASS'Y
CONTROL PANEL ASS'Y
COINCO COIN DOOR ASS'Y
POWER SUPPLY ASS'Y
REG/AUDIO P.C.B. ASS'Y
C.P.U. BOARD ASS'Y
BACK DOOR ASS'Y
MONITOR COLOR 19"
MIRROR
FLUORESCENT LAMP/SW. WIRED ASS'Y
SCREEND MARGUEE
VIEWING PANEL (PLEX.)
INSTRUCTION PANEL
SPEAKER
START BUTTON
FIRE
SHIELD BUTTON
CASH BOX WELD/ASS'y
CABINET REAR VEW
‘enero | pnav.arvo pare. | ASSmMOLY Ko centun.. anes ORR ““ CABINET REAR VIEW ee Be = ET
nev. | een Ter | ‘No.
REVISION ey
384-13-0200
C.P.U. BOARD ASS'Y
PARTS LIST
| NO. | PART NUMBER: | DESCRIPTION: | QNTY. | |
| 1. | 50210250 | P.C.B. (BARE) | 1 | |
| 2. | 50030210 | 1/4 WATT, 5%, 47 OHM, RESISTOR | 1 | |
| 3. | 50030125 | 1/4 WATT, 5%, 220 OHM, RESISTOR | 5 | |
| 4. | 50030095 | 1/4 WATT, 5%, 330 OHM,RESISTOR | 3 | |
| 5. | 50030010 | 1/4 WATT, 5%, 470 OHM, RESISTOR | 10 | |
| 6. | 50030051 | 1/4 WATT, 5%, 1K OHM, RESISTOR | 64 | |
| 7. | 50030087 | 1/4 WATT, 5%, 1.5K OHM, RESISTOR | 1 | |
| 8. | 50030001 | 1/4 WATT, 5%, 2.2K OHM, RESISTOR | 1 | |
| 9. | 50030006 | 1/4 WATT, 5%, 4.7K OHM, RESISTOR | 15 | |
| 10. | 50030149 | 1/4 WATT, 5%, 5.6K OHM, RESISTOR | 2 | |
| 11. | 50030165 | 1/4 WATT, 5%, 8.2K OHM, RESISTOR | 1 | |
| 12. | 50030063 | 1/4 WATT, 5%, 10K OHM, RESISTOR | 13 | |
| 13. | 50030106 | 1/4 WATT, 5%, 12K OHM, RESISTOR | - | 1 |
| 14. | 50030151 | 1/4 WATT, 5%, 22K OHM, RESISTOR | 4 | |
| 15. | 50030093 | 1/4 WATT, 5%, 27K OHM, RESISTOR | 1 | |
| 16. | 50030148 | 1/4 WATT, 5%, 39K OHM, RESISTOR | 8 | |
| 17. | 50030150 | 1/4 WATT, 5%, 47K OHM, RESISTOR | 2 | |
| 18. | 50030146 | 1/4 WATT, 5%, 15K OHM, RESISTOR | 1 | |
| 19. | 50030003 | 1/4 WATT, 5%,.330K OHM, RESISTOR | 1 | |
| 20. | 50040208 | 100V, .047M£, MYLAR CAPACITOR | 3 | |
| 21. | 50040001 | 25V, .1M£, CERAMIC CAPACITOR | 84 | |
| 22. | 50040049 | 25V, .01Mf, CERAMIC CAPACITOR | 1 | |
| 23. | 50040209 | 100V, 100P£, MICA CAPACITOR | 1 | |
| 24. | 50060060 | 25v, 10M£, ELECTROLYTIC, AXIAL CAP. | 2 | |
| 25. | 50060189 | 25V, 470Mf£, ELECTROLYTIC, AXIAL CAP. | 2 | |
| 26. | 50100042 | IN 751, DIODE | 1 |
31.
32.
33.
34,
35.
36.
37.
38.
39.
40.
41.
42.
43.
44,
45.
46.
47.
48.
49.
50.
52. 50100008
50070023
50370004
50130034
50020010
50020024
50020046
50020134
50010254
50010046
50010019
50010002
50010004
50010005
50010005
50010005
50010142
50010096
50010096
50010007
50010161
50010170
50010009
50010105
50010105
50010014 PART NUMBER:
Ls
Ls
Ls
Ls
Ls
Ls
Ls
Ls 384-13-0200
C.P.U. BOARD ASS'Y
PARTS LIST
DESCRIPTION:
LED
12.096 Mhz, CRYSTAL
TEST POINT
8 POSITION DIP SWITCH, SPST
2N 3643, TRANSISTOR (0-4)
2N 3904, TRANSISTOR (Q-2,7,8,9)
2N 3906, TRANSISTOR (Q-1,6)
2N 6044, TRANSISTOR (Q-3,5)
LM 324, I.C. (L-11)
IM 339, I.C. (M-11)
74874, I.C. (K-8)
74LS00, I.C. (K-3,H-5,N-8)
74802, I.C. (R-4)
7404, I.C. (R-2)
74804, I.C. (R-3)
74LS04, I.C. (P-3,J3-6,H-8)
7407, I.C. (B-12,D-12,f-12)
74808, I.C. (A-6,R-8)
74L808, I.C. (E-3,K-4,10,R-6,;P-8,B-11)
74LS10, I.C. (J-8)
74L811, I.C. (J-7,N-10)
74LS14, 1.C. (J-2)
7425, I.C (R-5)
74532, I.C. (F-3)
74LS32, I.C, (J-5,L-10,M-10,N-11}R-9)
74LS42, I.C. (H-3,H-4) QNTY.
Poe Nv FPF A NY WwW PF BF Be we Pe Be DD
yo ow
54.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
73.
74,
75.
76.
77.
78. PART NUMBER:
50010019
50010019
50010021
50010022
50010023
50010368
50010192
50010045
50010035
50010369
50010221
50010085
50010139
50010139
50010289
50010273
50010359
50010261
50010252
50010335
50010230
50010310
50010366
50010367
50010361
50010362 LS
Ls
LS
Ls
Ls
LS
Ls
LS
LS
LS
Ls
Ls
Ls
LS
LS 384-13-0200
C.P.U. BOARD ASS'Y
PARTS LIST
DESCRIPTION:
7474, I.C. (L=2)
74LS74, I.C. (L-3)
74LS83, I.C. (B-5,C-5,C-7,E-7)
74LS86, I.C. (H-7)
7490, I.C. (J-3)
74125, I.C. (J-10)
7448139, I.C. (H-2, J-4,P-4)
J4LS157, I.C. (E-5,F-5,7,9,10,L-5,6,7,H-6,10)
JA4LS161, I.C. (K-5,P-6,7,R-7,C-8,D-8,9,E-8, F~8,J-9) 74163, I.C. (M-2,3,N-2,3,P-2)
74LS163A, I.C. (L-8,M-8)
74LS8164, I.C. (C-9,A-10)
74L8175, I.C. (M-4,A-5)
748175, I.C. (K-9)
74LS195, I.C. (A-9,B-9,B-10)
74LS244, I.C. (B-1,C~1,E-2,F-2,M-5)
74LS251, I.C. (R-12)
74LS273, I.C. (D-5,7,10,K-6,7,A-7,B-7,R-10)
74L8374, I.C. (N-5,J-12)
27LS00, I.C. (L-9,M-9,N-9,P-9,10)
2101A-2, I.C. (B-6,C-6,D-6,E-6,9,10,F-6)
2114, (E~4,P-4)
6502A, (C-2)
POKEY, (C-3,4,D~3,4)
82825, RAM (P-11,H~11,N-6,7)
825123, PROM (C-11,D-11) QNTY.
PU WwW BP Ny NY N UY
nN NY UN @
No.
79.
80.
81.
82.
83.
84.
85. PART NUMBER:
50010363
50010364
50010365
50010171
50150111
50150060
50150061 384-13-0200
c.P.U. BOARD ASS'Y
PARTS LIST
DESCRIPTION:
828129, PROM (N-4)
82S131, PROM (A-8,B-8)
825137, PROM (H-9,C-10)
2716, EPROM
16 PIN I.C. SOCKET SOLDERTAIL
40 PIN I.C. SOCKET SOLDERTAIL
24 PIN I.C. SOCKET SOLDERTAIL QNTY.
a er
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24,
25.
26. PART NUMBER:
50030231
50030357
50030358
50120021
50030345
50030019
50030256
50030051
50030063
50030014
50030101
50030005
50030149
50030359
50030094
50030360
50060222
50060189
50060223
50060224
50060095
50040001
50040049
50040206
50040207
50100028 384-13-0100
REG/AUDIO P.C.B. ASS'Y
PARTS LIST
DESCRIPTION:
2.7 OHM, 1 WATT, 5%, RESISTOR
4 OHM, 5 WATT, 5%, WIREWOUND RESISTOR
.1 OHM, 7 WATT, 3%, WIREWOUND RESISTOR
1K OHM, VERT. P.C.B. MOUNTING CERMET TRIM POT
1 OHM, 1/4 WATT, 5%, RESISTOR
10 OHM, 1/4 WATT, 5%, RESISTOR
100 OHM, 1/4 WATT, 5%, RESISTOR
1K OHM, 1/4 WATT, 5%, RESISTOR
10K OHM, 1/4 WATT, 5%, RESISTOR
270 OHM, 1/4 WATT, 5%, RESISTOR
33 OHM, 1/4 WATT, 5%, RESISTOR
3.9K OHM, 1/4 WATT, 5%, RESISTOR
5.6K OHM, 1/4 WATT, 5%, RESISTOR
7.5K OHM, 1/4 WATT, 5%, RESISTOR
220 OHM, 1/2 WATT, 5%, RESISTOR
22.OHM, 10 WATT, 5%, WIREWOUND RESISTOR
1000Uf, AXIAL ELECTROLYTIC @ 25V, CAP.
470U£, AXIAL ELECTROLYTIC @ 25V, CAP.
22U£, AXIAL ELECTROLYTIC @ 35vV, CAP.
3300Uf£, AXIAL ELECTROLYTIC @ 35v, CAP.
1U£, AXIAL ELECTROLYTIC @ 50V, CAP.
.1U£, CERAMIC DISC, RADIAL @ 25V, CAP.
-01U£, CERAMIC DISC, RADIAL @ 25v, CAP.
-001U£, CERAMIC DISC, RADIAL @ 25V, CAP.
.22Uf, CERAMIC DISC, RADIAL @ 25v, CAP.
IN 4002 DIODE QNTY.
BN FP FP BB
NN WwW
WwW YN F YO B&B N
N
30.
31.
32.
33.
34,
35.
36.
37.
38.
39.
40.
41.
42.
43.
44,
45.
46.
47. PART NUMBER:
50100101
50020131
50020037
50020132
50010258
50020133
50010360
50150196
50150195
50150336
50150194
50270104
50370002
50370003
50150247
10010032
10150003
10010146
384-03-0600
50370004
50210251 384-13-0100
REG/AUDIO P.C.B. ASS'y
PARTS LIST
DESCRIPTION:
IN 5401 DIODE
TIP 32, TRANSISTOR
2N 3055, TRANSISTOR
LM 305, 5V, REGULATOR
7812 + 12V, REGULATOR
7905 - 5V, REGULATOR
TDA 2002 A, 8 WATT, AMPLIFIER
9 PIN MOLEX RECEPTACLE W/EARS OR TABS
12 PIN MOLEX RECEPTACLE W/EARS OR TABS
4 PIN MOLEX RECEPTACLE W/EARS
6 PIN MOLEX RECEPTACLE W/EARS OR TABS
THERMO COMPOUND
THERMO CONDUCTIVE SILICON INSULATOR
10-3 SILICON INSULATOR
FEMALE PINS MOLEX, P.C.B. MOUNT
6-32x1/2 PA/PH/MS
6-32 KEP NUT
6-32x%3/8" NYLON SCREW
HEAT SINK
TEST POINT
REG/AUDIO II P.C.B. (BARE) QNTY.
NP FR
A/R
ue
AI i Heid oid aaa mS 4g Ue SSDESSE Sela ve boESGrS ES >Sh ESSE
ti
eI Kizsirat
FONPEO ale Olm| & PEETE erry Roman SO : wre Hi a on ARE THA] TH als Bae ig Sool conc-unnte ans ShsMis
Ei TTS sialyl BIS ‘SV RIN” |-sevse. le SENSE So 5yREe [sv AEC Avian FODIETIN,
RVC
(oe RB ibs; dehhant
SRE,
36 VAC EVAC. NCTE IS ES
sic-6N> 103 voc RES. a ~] eeco-tennc id hewn? ‘sou aeeeseane Be
+108 we URES {I GAD. 3EVACHI 36vACI0 Brac Hr EI VACLO
KEY oe TSSIG8 SIS SI@NT
feovac
papery
awe aT raaVD
ror DHT ONSP-LNIP TIOT La 3 BG
Sr ad We
c: esas INIA Nae
wous4ac f¥ Sco I fale PISS) are lool Ele B
THE MATERIAL CONTAINED HEREIN IS CONFIDENTIAL
AND NO PART OF IT CAN BE REPRODUCED WITHOUT THE EXPRESSED PERMISSION OF CENTURI, INC
EXPRESSED PERMISSION OF CENTURI, INC. 7P, +10-3y0C UNREG
al 410.3V0e. UNREG oe P32 ‘We. 6N0(2) cnet (Bt -— I Se. ae (B] AuoIo 2INPET
oe avo 1 weve 1p Ho xe ba “La sree SI speee
alea [" srk ae SPKR Late sPke 28TH ac. APV'D PROD. = ‘ary.
‘ASSEMBLY NO
TOLERANCES
FRACTIONS
DECIMALS 2 PL. DECIMALS 3 PL HOLES
Rev. | ECN tev. | owe. REVISION BY ANGLES SHT. MET BENDS. ® + Wales Otherwise Specified 132. 015, centon.. HIALEAH, FLORIDA 33014
NAME SCHEMATIC, REGULATOE AUDIO. PC.BD
MATS. HEAT TREAT. FINISH
17-B2. Se [SB17-020d""|
B 301 ” nau) C280 TE) in one | A womans aE
(08 DELAY TENNAL PILYHPHIy| Hej Vaesromae zn $ “Snousves Ta aOR Tee “umues SaaS aT ‘SSONVUTIOL
‘on mamesy | “AiO Tana cous] aaa 30 Ele hr AR
aus BREF Pb QPReRRe raoove “oui ‘uninaa 40 Norseimuza a3ssauexa ‘is snovisun azongousay 38 vo JI40 Luvs ON GNY Ivldwaalanco st NIaWaH GaNIWINOg Wwisam IK
vevauk a7 oe 12 8V—hne caves WA | sete ev —tlas |
a 4 a : “eaweT NEY ERCHNG-
He ncr ADO™ 2 ncrapee fer ABDI eT ALD = ase 2p" oi ase me di i BS Fickle, 4p ch) SS wae. crea Ses FP SCHEMATEC TUNNEL BUVT PC. | 2oFsB
ea FevisiOn BY | tr mer sens ©
Back oF
“on | an noa_| Agu
nau] CEO LO) Binal FEV UD) 7 Ci 3 ae NoIsiaay
Se Dk LF TEN. DLP HPS srl S20NVESIOL
aR AWRY [AD TOAW Gow | Gna = 2852 vise See HE ena af o&
est visite alEusoay
epee a fae mearewnsAg ui ed Wyle ome y mann ode ; > § > Fy &
i pecorer L502 E ‘OMI ‘WinN39 40 NoIssiMU24 case3HaXa ML Lnasiuim az9q\00HaaH 38 NVO 1I-40-14v4 ON ONY 'GVIENSGIINGO 8 NIBWSH GSMIVLNOD VIUSLVN 3H.
“TWE MATERIAL CONTAINED HEREIN IS CONFLOENTIAL |ANONG PART OF T CaN Be REPRODUCED WITHOUT THE. EXPHeSSED PERMISSION OF CENTURY, INE-
FUNCTION
ov Ee Te TF Ey atoms] EALUF eed “HIALEAH, FLORIDA 33014, F SCHEMATIC TUNNEL HUNTPC BD ooo ae far Tac [FH me Giebe
Rev. | Eon ter | ‘no. REVISION ey
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Sia pecececers a fs a corr. =
TUNNEL HUNT
Taco aa —ufks ! Gesoe
cunnrost 7] armnrose— 4| Loe ie moriat o recess >
contin. ae a
TUNNEL HUNT
pe" [igar17-0300]~
" is
: reneo oo
mco: lar te gees
weoce SL
morviot —Zlas 9 mor ing Shea Live castes § oy [Ht une coua—Zlao, Lnecon! Slat LNecog Slap are
odcndadad
< + le Wh ay care [2 ore a, 1. se Is. i israc: zero genaa
ju RA He eave [perenne Por emf [=[eecsncer B03 20d “alias erry
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
centuri. Centuri, Inc. ¢ 245 W. 74th Place ¢ Hialeah, Florida 33014 Telephone: 305-558-5200 Telex: 803694 e ANSB Centuri weausae grew ATARIS