Asteroids TM-143 1st Printing (BAD SCAN)
Asteroids (rev 4) (Atari, 1979) · Technical Manual · 38 pages · 28 sections · original scan
S
a
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Lists
Published by: ATARI INC 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
Copyright © 1979 by Atari, Inc. All rights reserved
No part of this publication may be reproduced by any mechanical, Photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
Lithographed in the U.S.A. 10H. A
ATARI
Table of Contents
1 Location Setup A. New Parts... 0... ccc cece cere e cee ene aee B. Game Inspection . C. Game Installation...
- Voltage Selection ....... .
- interlock and Power On/Off Switches
- GameFuses ............... cee Self-Test Procedure . Game Play ......
- AttractMode....
- Ready-to-Play Mode
- PlayMode .......... mp
- High Score Initial Mode ............... : seeeeee
2 Maintenance and Repair A. Cleaning B. Fuse Replacement. .... C. Opening the Control Panel ..
- Leaf Switch Replacement.
- LED Switch Replacement TV Monitor Replacement....... Printed Circuit Board Replacement Fluorescent Tube Replacement . D. E. F. G.
3 Illustrated Parts Lists Game Operation.............0.00.- fue eee cceenne WOMMOAMMWWOwWa
® List of Illustrations
Figure1 Overview of Game Figure 2 Installation Requirements ................--..--5 Figure 3 PowerSupply .......... 2. cece eee eee eee Figure 4 Interlock and Power On/Off Switches . Figure 5 —_ Location of Self-Test Switch, Volume Control and Option Switches . Figure6 = Self-Test Procedure Figure 7 Option Switch Settings . . Figure 8 Opening the Control Panel Figure9 TV Monitor Removal..................005 Figure 10 Game and Regulator/Audio PCB Replacement . Figure 11 Fluorescent Tube Replacement ...........
- Figure 12 Power Distribution .....................-.- Figure 13 Signal Distribution . . Figure 14 Final Assembly Figure 15 Control Panel Assembly Figure 16 Asteroids Game PCB Assembly . Figure 17 Regulator/Audio PCB Assembly Figure 18 Power Supply Assembly for X-Y Games. Figure 19 Main Harness and Component Assembly. Figure 20 Fluorescent Light Assembly Figure 21 Coin Door Assembly Figure 22 Front Bezel Assembly
» Location Setup
A. New Parts
The Asteroids game has three new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are:
- Power Supply Assembly. It covers a wider voltage range than before, has higher reliability, a smaller overall size, and ail fuse numbers and fuse amperages are marked directly on the metal chassis.
- Game PCB Circuitry and TV Monitor. Most video games to date have used the raster scan method of display. This game uses vector generation with X and Y axes to allow greater contrast, a greater number of moving objects on the screen, and lines at any angle to be “drawn” on the screen.
Throughout this manual, wherever one of these three new parts is mentioned, you will see this symbol in the page margin: \
ATTRACTION PANEL
TV MONITOR SHIELD
CONTROL PANEL
“S
XY TV MONITOR
REGULATOR: AUDIO PCB
GAME PCB COIN DOOR
POWER SUPPLY
POWER ON/OFF SWITCH ‘ACCESS PANEL
Figure 1 Overview of Game
® B. Game Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
[boner NOTE nent | Do not plug the game in yet!
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: a. Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. b. Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
c. Note the location of the game's serial number—it is on the metallic label on the back of the game cabinet. Verify that that serial numbers stamped on Game PCB, Regulator/Audio PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. d. Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting. Asteroids:
C. Game Installation
Figure 2 Installation Requirements
Power 175 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 65 x 79 cm (25% x 31 in.) Game Height 184 om (72% in.)
ya -)
Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location's line voltage. Check the wire color on the plug and see if it is correct per the list below.
- Voltage Seiection
Line Voltage Range Voltage Selection Plug Color
90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown
- Interlock and Power On/Off Switches
To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.
Check for proper operation of the interlock switches by performing the following steps:
- Unlock and open the access panel and the coin door.
- Plug the AC line power cord into an AC outlet.
- Close the access panel and coin door.
SWITCH COVER
SAFETY INTERLOCK SWITCH COVER
POWER ON/OFF SWITCH
Figure 4 Interlock and Power On/Off Switches
- Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture. 5, Slowly open the rear access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5cm (1 inch). Close and lock the access panel and repeat this step with the coin door.
- If the results of step 5 are satisfactory, the interlock switches are operating properly. if the TV Monitor doesn't go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the on position.
- Game Fuses
For continued protection of your game, as well as for the safety of the players, fuses must be replaced only with fuses with identical ratings. These ratings are shown in Figure 18. See the Schematic Drawing Package for fuse functions.
VOLUME CONTROL
VOLUME DECREASE: TURN CLOCKWISE
SELF-TEST SWITCH Information on the TV monitor fuses is contained in the TV monitor manual that is supplied with this game.
D. Self-Test Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the TV monitor and the game speaker; no additional equipment is necessary.
Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game's options.
To run the self-test, follow the instructions outlined in Figure 6.
OPTION SWITCHES
Figure 6 Self-Test Procedure
INSTRUCTION
- Set self-test switch to on position (see Figure 5).
- Activate all control panel and coin door switches. RESULTS IF TEST PASSES RESULTS IF TEST FAILS TV monitor displays RAM FAILURE is indicated by a sequence of from 1 to 6 tones. A low-frequency picture as shown in Figure 7.
1 PLAYER START and 2 PLAYER START LEDs are lighted. Highpitched click for each activated switch. tone is heard for each good RAM chip. A much iower frequency is heard for a failing RAM chip. The sequence stops with the last failing RAM chip. To restart the sequence, press the Reset pushbutton on the game PCB or set the self-test switch to off, then again to the on position. Identify the bad RAM chip with table below. Example: Three tones. then a tone of much lower frequency indicates failure of RAM chip R4.
TONE # M_CHIP LOCATION
D2 E2 M4 Ra N4 P4 Omaens
ROM/PROM FAILURE is indicated by two lines of numbers in the upper lefthand corner of the display. The number on the first line indicates the faiting ROM/PROM chip(s). Identify the bad ROM/PROM with tabie below. The number on the second line indicates the failing data bit of the failing ROM/PROM. Identify the bad bit with the second table below. If more than one bit is failing, the displayed number(s) are nexadecimal combinations of the numbers shown below. Examples:
- If bits 02 and DS fail, C is displayed.
- If bits D2, D3 and D7 fail, 8C is displayed.
- If bits D4 and D6 fail, 30 is displayed.
- If bits 01, D3, D5 and D6 fail, 6A is displayed
DISPLAYED NO. FAILING ROM/PROM
| ‘ | N/P3 | Ka, L4 |
2 F2, H1
| 3 | FA | F2, 41 | wu |
4 H2, J1
| 5 | DYE | H2, J1 | M2, M1 |
6 J2, K1
| 7 | C1 | K1, J2 | N2,.N1 |
DISPLAYED NO. FAILING BIT 1 00 2 D1 4 D2 8 03 10 D4 20 0S 40 12)3} 80 b7
RAMSEL SIGNAL FAILURE is indicated by PAGE SELECT ERROR message at Jower middle of display.
1 PLAYER START and/or 2 PLAYER START LEDs not lighted.
High-pitched click sound is not heard for any particular switch.
Figure 7 Option Switch Settings
To change toggle positions of the switch assembly, you need not remove the game PCB. The switch, usually colored biue, is easily accessible when the game PCB is mounted in place.
When changing the options, verify proper results on the TV monitor display during self-test. A switch toggle in the on position is indicated by a 0 for that switch on the TV monitor display. A switch in the off position is indicated by a1.
Toggle settings of 8-toggle switch on game PCB
1 2 3 4 5 6 7 8
Option Suggested
Setting
ON ON OFF ON ON OFF OFF OFF
ON OFF
ON OFF
ON ON OFF ON ON OFF OFF OFF
ON ON OFF ON ON OFF OFF OFF
LEFT COIN MECH MULTIPLIER SWITCH TOGGLE 1 RIGHT COIN MECH MULTIPLIER English Language German Language French Language Spanish Language 4-Ship Game 3-Ship Game “ Left Coin Mech x 1 a Left Coin Mech x 2 Right Coin Mech x Right Coin Mech x Right Coin Mech x Right Coin Mech x Free Play 4 Coin 2 Plays 1 Coin 1 Play a 2 Coins 1 Play
SWITCH TOGGLE 8
Photograph above shows toggles 1, 2, 4-7 ‘on, and toggles 3 and 8 off.
E. Game Play
Atari's Asteroids has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled.
- Attract Mode
The attract mode begins when power is appiied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test. In this mode, the TV monitor displays two possible pictures. Both pictures have three score values across the top of the screen and a message that states the number of coins for a game. The middle score represents the high score to date. The left score is for player 1. The right score is for player 2.
One picture displays asteroids and an occasional enemy spaceship “floating” across the screen. This picture remains displayed for 16 seconds. The second picture displays up to 10 of the highest scores since the game was last powered up or since the last self-test.
- Ready-to-Play Mode
This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed. When this mode begins, the message PUSH START flashes immediately below the center score at the top of the screen. The displayed pictures are otherwise the same as those shown in the attract mode.
- Play Mode
The play mode begins when either start push- q
button is pressed. The mode ends when the player's last ship of the game is lost.
If the 1 PLAYER START pushbutton is pressed, the following picture is displayed: the PLAYER 2’s score disappears; the PLAYER 1’s score becomes 00, and the number of ships for the game appears below that score. The message PLAYER 7 also appears below the high score to date. Two seconds after pressing the 1 PLAYER START button the PLAYER 1 message disappears, and the game ship appears at the center of the display. Four large asteroids appear and drift in from the outer edges of the display.
{if the 2 PLAYER START pushbutton is pressed, the following picture is displayed: the PLAYER 1 and PLAYER 2 scores become 00, and four ships for the game appear below each score. The player 1 score also flashes as the message PLAYER 1 appears below the high score to date. Two seconds after the 2 PLAYER START pushbutton is pressed, the PLAYEA 1 message disappears. The game ship for player 1 appears at the center of the display as four large asteroids appear and drift in from the outer edges of the display.
When the last ship of the game is destroyed, the message GAME OVER appears below the high score. This message remains for 3 seconds before the high score initial mode begins.
- High Score Initial Mode
This mode immediately follows the play mode. It ends after the player has completed “signing” his or her initials, The display of the mode includes instructions for players to sign their initials.
Maintenance
® and Repair The Atari Asteroids game requires certain Maintenance to keep it in good working order. Clean, properly maintained games attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if light-emitting diode or leaf switches are broken or if LEDs have burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts: for details see this chapter.
A. Cleaning
The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.
B. Fuse Replacement
This game contains six fuses—all on the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Figure 18 of this manual. See the Quadrascan TV monitor manual, TM-146, for the monitor fuse data.
C. Opening the Control Panel
Prior to repairing or replacing any switch on the control panel or prior to removing the TV monitor, unplug the game. Then open the coin door.
Reach through the opening and remove both sets of wing nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 8). The two carriage bolts will remain in the control panel.
Lift up on the control panel and tilt it towards you. Be sure that the acrylic TV monitor shield does not fall on you. The top edge of the control panel acts as a retainer strip for the shield: once the control panel is opened, the shield is free and could slide out under its own power.
- Leaf Switch Replacement
All five of these leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is in very bighhumidity locations.
Don’t burnish the switches. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.
To replace any switch, remove both of its screws with a Phillips-head screwdriver—see Figure 8.
!f the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the control panel should not spin, due to its design.
- LED Switch Replacement
The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 8.
- Remove the wires from the suspected switch.
- Set multimeter to ohms scale. Set ohms scale toR x 1, then zero the meter.
- Connect multimeter leads to appropriate LED
switch contacts (see Figure 8 for designation of
switch contacts and meter lead placement).
- Check contacts (push and release the switch button) for closed and open continuity.
- If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure. q
COMMON . INI CONTACT , UGHT-EMITTING DIODE (L.E.D.) CONTACTS
NORMALLY OPEN (N.O.) CONTACT
NORMALLY CLOSED (N.C.) CONTACT
L.E.0 SWITCH TO REMOVE TURN COUNTERCLOCKWISE
To remove LED switch:
@ Remove all wires from the taulty switch. © Turn the switch counterclockwise while holding the black cone-shaped nut on the outside of the control panel. © Install a new switch using the reverse procedure. @ Reconnect the hamess wires,
LEAF SWITCH
TURN NUT TO REMOVE WHITE BUTTON
Figure 8 Opening the Control Panel
D. TV Monitor Replacement
High voltages may exist in any television unit, even with power disconnected. Use extreme caution and do not touch electrical parts or the TV yoke area with your hands or with metal objects in your hands!
If you should need to service or replace the Quadrascan X-Y TV monitor, you must first remove it from the game cabinet. Follow the instructions below, and refer to Figure 9. ad
o Open the control panel as described in Section C, Opening the Control Panel. Be sure the game is unplugged from its wail outlet! Remove the acrylic TV monitor shield by sliding its lower edge out. Working up from the bottom side corners, carefully pry loose the two side flaps of the colorful 2-piece cardboard bezel. (A 4-inch strip of double-sided adhesive tape is centered behind both side flaps, flush with each edge.) Remove the bezel as a complete unit—do not remove the smaller part first. Open the rear access panel and unplug the TV monitor harness connectors—each one is a 6-pin connector on the TV’s (PCBs). Remove the four sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the metal TV chassis. Carefully slide the TV monitor chassis out the front of the game.
Disassemble in the order indicated
Figure 9 TV Monitor Removal
E. Printed Circuit Board Replacement
You may wish to remove the game printed circuit board (PCB) or the Regulator/Audio PCB for service or inspection. To do this, refer to Figure 10 and proceed as follows:
1. 2. Open the rear access panel. Locate the securing screws and fiber washers that hold down the PCB in its slots, and remove them. (The game PCB has two, the Regulator! Audio PCB has one set of this fastening hardware.) tf you are removing the game board, first remove the two machine screws that hold the edge connector to the small black connector mounts, along the game PCB's edge. Then unpiug the edge connector on the game PCB. If you are removing the Regulator/Audio PCB, simply disconnect the three smail harness connectors on this board. Carefully slide either PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. Replace the securing screws and fiber washers in the PCB. Reinstall the machine screws into the black connector mounts on the PCB. Close and lock the rear access panel. Check that the operation of the game is correct and perform the self-test. This is especially important with any game when you replace a PCB. Normally the only adjustments on the Asteroids game are option switch changes (made on the 8-toggle DIP switch). Unless you are qualified technician, do not turn any of the four knobs near the game PCB’s edge cannector. Also do not turn the small knob on the RegulatoAudio PCB.
REGULATOR! AUDIO PCB
GAME PCB
Figure 10 Game and Regulator/Audio PCB Replacement
F. Fluorescent Tube Replacement
CAUTION
If you drop a fluorescent tube and it breaks, it will explode! Shattered glass can fly 6 feet or more from the explosion. Use care when replacing any fluorescent tube.
To replace the white fluorescent tube behind the graphics attraction panel, follow this Procedure (see Figure 11).
- Remove the three Allen-head screws at the top of the game. They secure the metal retainer for the silk-screened panel. Remove the retainer completely.
- Tilt the top of the attraction Panel towards you, then lift it up and out of the bottom retainer.
- Remove the two grey clips from the fluorescent tube. Now turn the tube one quarter turn in either direction. Remove the tube and both orange clips.
- Replace with a new tube. If you move games a lot from one location to another, you should reuse the orange and grey clips. They provide extra protection against vibration loosening the tube out of its fixture.
- Close up the game by following these instructions in reverse order.
G. Game Operation
With this manual you received two large sheets that contain the wiring and schematic diagrams for the Asteroids game. Sheet 1, Side A, includes information that shows the arrangement of these dia-
Figure 11 grams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.
Atari’s Asteroids is a microprocessor-contralled game. The microprocessor is contained on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio PCB and control panel.
The TV monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes, Since the location of the beam of the monitor is totally controlled by the X and Y axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X and Y axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis and 768 steps for the Y (vertical) axis. The Z axis merely turns the beam on and off.
The Regulator/Audio PCB performs two funtions:
- regulates the + 10.3 VDC from the Power supply to +5 VDC, and 2) amplifies the audio output from the game PCB. The +5 VDC from the Regulator! Audio PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio PCB directly drives the game speaker and is controlled by the volume control mounted inside the coin door.
The Power Supply is the source of all voltages in the game. These voltages are protected by five fuses in the fuse block on the Power Supply chassis. The primary winding of the Power Supply transformer is protected by the cartridge-type fuse in the power supply chassis.
Figure 12 illustrates the distribution of power in this game. Figure 13 illustrates the distribution of signals.
Fluorescent Tube Replacement
FLUORESCENT LAMP
TV MONITOR
REGULATOR/AUDIO PCB
GAME PCB
COIN DOOR —1
g 5 og g| 3/3 POWER INTERLOCK 3 zg SWITCHES
POWER SUPPLY
AC POWER CORD
’ Figure 12 Power Distribution
nee
GAME SPEAKER
TV MONITOR
val CONTROL REGULATOR/AUDIO PCB PANEL ! ~
= \ \'e\8 > PAPARCAP AEA AEA GS CACACACAWACAMAC-S AS ras 3 O BAL 5 \ 7 i gl \\\ eo 2 \ oa i} a F| : os 2 8 \ — Ss 3 . 8 33). s Pi] 3 x
VOLUME CONTROL Zi, /
KES COIN DOOR a mS Ca a I ee — GAME PCB
Figure 13 Signal Distribution
Illustrated Parts Lists
The purpose of this chapter is to provide you with
() the necessary information for ordering replacement
parts for your Atari Asteroids game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc. When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
ae
ae
TONAL MES
- ~-@8) e-rtes | ~a@enes @D2acs @.
test —er) @)
NOTICE TG ALL PEAS: CONFIDENTIAL Rep
Figure 14 Final Assembly A035050-13 B
Figure 14 Final Assembly Parts List
| item | Part No. | Description | |
| 2 | A035053-01 | Control Panel Assembly—see Figure 15 | |
| 3 | A035056-01 | Access Panel Assembly | ye s-N) |
| 4 | A034986-01 | Asteroids Game PCB Assembly (PROM version)—see Figure 16 |
OR A034986-02 Asteroids Game PCB Assembly (ROM version)
| 5 | A034485-01 | Regulator/Audio PCB Assembly—see Figure 17 | “Ss |
| 6 | A034561-01 | Power Supply Assembly for X-Y Games—see Figure 18 | |
| 7 | A036158-01 | Main Harness and Component Assembly—see Figure 19 |
OR A035158-02 Main Harness and Component Assembly
| 8 | A034628-01 | Light and Speaker Harness Assembly |
| 9 | A034841-01 | Strain Relief Power Cord (domestic) |
OR A034863-01 Strain Relief Power Cord (German)
| 10 | A034762-01 | Fluorescent Light Assembly—see Figure 20 |
| it | A030268-01 | Coin Box Assembly |
| 13 | A021084-01 | Voitage Selection Plug, 100V |
A021084-02 Voltage Selection Plug, 120V A021084-04 Voltage Selection Plug, 220V A021084-05 Voltage Selection Plug, 240V
| 14 | A009083-xx | Coin Door Assembly—see Figure 21 | |
| 15 | 035052-01 | Cardboard Bezel with Graphics | |
| 16 | 034457-01 | Speaker Grille | |
| 17 | 035051-01 | Acrylic Attraction Panel with Graphics | |
| 18 | 035049-01 | TV Monitor Shield with Graphics | |
| 19 | 034515-01 | Upper Retainer Strip | |
| 20 | 034516-01 | Lower Retainer Strip | |
| 23 | T™M-143 | Asteroids Technical Manual | |
| 24 | 001638-01 | Control-Panel Mounting Bracket | |
| 27 | 006870-01 | Coin Box Bracket | |
| 28 | 007882-02 | Interlock Switch Cover | |
| 29 | 007103-01 | On/Off Switch Cover | |
| ca | 030868-01 | PCB Connector Mount | |
| 32 | 034536-02 | Foam Vibration Damper for Game PCB | |
| 33 | A035319-01 | Coin Door Adapter Harness Assembly | |
| 34 | 48-001 | 8” High-Fidelity Speaker | |
| 36 | 035437-01 | Connector Mount for TV Monitor | “SS |
| 56 | 92-042 | 19” X-Y Black-and-White TV Monitor | |
| 57 | 75-07017 | Spacer | |
| 60 | 99-11006 | Lamp Socket Clips {a set includes 2 pieces) | |
| 61 | 70-303 | 18” 15-Watt Cool White Fluorescent Lamp | |
| 65 | TM-146 | Manual for Quadrascan X-Y Monitor | |
| 66 | DP-143-01 | Asteroids Schematic Drawings (Sheet 1) | |
| 67 | DP-143-02 | Asteroids Schematic Drawings (Sheet 2) |
Figure 15 Control Panel Assembly A035053-01 A SS SSS
| item | Part No. | Description |
eee a6a{otw@s=$—=—0000N0
| 1 | 035047-01 | Control Panel with Graphics |
| 2 | 035046-01 | Control Panel Support |
| 3 | 62-039 | Light-Emitting Diode Switch |
| 4 | 001856-01 | Aluminum Switch Bushing |
| 5 | A020895-01 | White Pushbutton Assembly |
| 6 | 020893-01 | Leaf Switch |
| 7 | 021105-01 | Metal Header Plate for Leaf Switch |
| onl | A035159-01 | Control Harness Assembly |
| 17 | 75-07054 | Nylon Spacer |
Wotan. Mocvas at eR sveasce ar oe |
mbly A e PCB Asse ids Gam 01 and 16 Astero A034986-
Figure
he Foenion, OTMLLING 7418 2aS, BE RES. verwoRes,
Hey Re ou ve CSiMe, TSITOS Mba na ae
beta URE THe Lc. POSITION, Board is Permanently marked -01 or -02 after
POSITION ES (ESSTALONE AIABEOS “A034986", located between rows 10 & 11 (01 for
PROM, -02 for ROM version).
Figure 16 Asteroids Game PCB Assembly Parts List
| fttem | Part No. | Description (Reference Designations and Locations in Bold) |
| 2 | 100000-270 | 27 Ohm, +5%, %4W Resistor (R72) |
| 3 | 100000-680 | 68 Ohm, +5%, “%4W Resistor (R71) |
| 4 | 100000-121 | 120 Ohm, +5%, YW Resistor (R105, 109) |
| 5 | 100000-151 | 150 Ohm, +5%, ¥4W Resistor (R55) |
| 6 | 100000-331 | 330 Ohm, +5%, %W Resistor (R30, 31, 112, 113, 115) |
| 7 | 100000-471 | 470 Ohm, +5%, VW Resistor (R32) |
| 8 | 100000-681 | 680 Ohm, +5%, %W Resistor {R57, 61) |
| 9 | 100000-102 | 1K Ohm, +5%, %4W Resistor (R27, 29, 53, 73, 85, 86) |
| 1 | 100000-122 | 1.2K Ohm, +5%, %4W Resistor (R35, 100) |
| 12 | 100000-222 | 2.2K Ohm, +5%, YW Resistor (R36, 75, 117, 123) |
| 13 | 100000-272 | 2.7K Ohm, +5%, YW Resistor (R66) |
| 14 | 100000-332 | 3.3K Ohm, +5%, YW Resistor (R56, 65, 74) |
| 15 | 100000-392 | 3.9K Ohm, +5%, YW Resistor (R39, 64, 106-108) |
| 16 | 100000-472 | 4.7K Ohm, +5%, %4W Resistor (R37, 82, 102) |
| 17 | 100000-562 | 5.6K Ohm, +5%, %4W Resistor (R40, 62, 67) |
| 18 | 100000-682 | 6.8K Ohm, +5%, %4W Resistor (R49, 104) |
| 20 | 100000-103 | 10K Ohm, +5%, %W Resistor (R9-26, 28, 33, 38, 54, 58-60, 63, 69, 70, 79, 80, |
87-99, 103, 110, 111, 116, 122)
| 21 | 100000-123 | 12K Ohm, +5%, %W Resistor (R43) |
| 22 | 100000-153. | 15K Ohm, +5%, %W Resistor (R68) |
| 23 | 100000-183 | 18K Ohm, +5%, ¥W Resistor (R51) |
| 24 | 100000-223 | 22K Ohm, +5%, %W Resistor (R1-8, 34, 41, 45, 50) |
| 25 | 100000-333 | 33K Ohm, +5%, YW Resistor (R52) |
| 26 | 100000-473 | 47K Ohm, +5%, “%W Resistor (R42, 44, 48, 76, 78, 83, 114) |
| 27 | 100000-563 | S6K Ohm, +5%, %W Resistor (R118, 119, 124, 125) |
| 28 | 100000-104 | 100K Ohm, +5%, %4W Resistor (R46, 81, 84) |
| 29 | 100000-224 | 220K Ohm, +5%, %4W Resistor (R47) |
| 30 | 100000-274 | 270K Ohm, +5%, “4W Resistor (R101) |
| 33 | 100000-393 | 39K Ohm, +5%, %W Resistor (R77) |
| 34 | 19-007 | 10K Ohm, 8-Pin Resistor Network. Use with the LS170 only—item 120. (RP1, 2) |
| 35 | 19-315103 | 10K Ohm Vertical PCB-Mounting Cermet Trimpot, Bournes Series |
3352V-1-10K (R120, 121, 126, 127)
| 39 | 21-101104 | 1 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C64, 67-69) |
| 40 | 21-101224 | -22 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C33) |
| AL | 21-101473 | .047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C46) |
| 44 | 24-250105, | 1.0 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C25, 70, 90, 92, |
93)
| 45 | 24-250107 | 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C19) |
| 46 | 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C86, 87) |
| 47 | 24-250226 | 22 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C117) |
| 49 | 27-250102 | .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C56) |
| 50 | 27-250103 | .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C27, 32, 36, 40, 55, 58) |
| 51 | 27-250104 | -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-18, 20-23, 26, 28-31, 34, 37, |
41-44, 49, 51-54, 57, 60, 61, 63, 65, 66, 71-85, 91, 94-96, 99-101, 103, 104, 107-109, 111, 112, 114-116)
| 53 | 28-101100 | 10 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C97, 105) |
| 54 | 28-101680 | 68 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C102, 110) |
| 55 | 28-101101 | 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C89) |
| 56 | 28-101221 | 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C98, 106) |
| 57 | 28-101271 | 270 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C59) |
| 58 | 28-101301 | 390 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C88) |
| 61 | 29-006 | 1.0 uf, + 10%, 35V Tantalum Capacitor (C24, 35, 47, 50, 62, 113) |
| 63 | 29-046 | 10 uf, + 10%, 20V Tantalum Capacitor (C38, 39, 45, 48) |
| 66 | 31-1N914 | 75V 1N914 Switching Diode (CR1-4, 6-8, 15) |
| 67 | 31-1N4001 | 50V 1N4001 Silicon Rectifier Diode (CR9-12) |
Figure 16 Asteroids Game PCB Assembly, continued Parts List
| item | Part No. | Description (Reference Designations and Locations in Bold) | |
| 68 | 31-1N756A | 8.2V, 45%, 1N756A Zener Diode (CR13, 14) | |
| 71 | 33-2N3906 | Type 2N3906 PNP Switching and Amplifying Transistor (Q1-5, 7, 10) | |
| 72 | 34-2N3643 | Type 2N3643 NPN Silicon Transistor (Q6) | |
| 73 | 34-2N3904 | Type 2N3904 NPN 60V 1-WattTransistor (Q8, 9) | |
| 74 | 34-2N6044 | Type 2N6044 Darlington NPN Transistor (Q11-13) | |
| 78 | 37-74LS00 | Type 74LS00 Integrated Circuit (N5, C6) | |
| 79 | 37-74LS02 | Type 74LS02 Integrated Circuit (D6) | |
| 80 | 37-7404 | Type 7404 Integrated Circuit (H10) | |
| 81 | 37-74LS04 | Type 74LS04 integrated Circuit (B5, L5) | |
| 82 | 37-7406 | Type 7406 Integrated Circuit (N9) | |
| 83 | 37-74LS08 | Type 74LS08 Integrated Circuit (E6, K6, R7, B8) | |
| 84 | 37-74LS10 | Type 74LS10 Integrated Circuit (A8) | |
| 85 | 37-74LS14 | Type 74LS14 Integrated Circuit (B&) | |
| 86 | 37-741S20 | Type 74LS20 Integrated Circuit (E5) | |
| 87 | 37-74LS32 | Type 74LS32 Integrated Circuit (M5, N6, BS) | |
| 88 | 37-74LS842 | Type 74LS42 Integrated Circuit (L6, E7, E8) | |
| 89 | 37-74LS74 | Type 74LS74 Integrated Circuit (D4, A7, R8) | |
| 91 | 37-74LS83 | Type 74LS83 Integrated Circuit (M6) | |
| 92 | 37-74LS86 | Type 74LS86 Integrated Circuit (P5) | |
| 93 | 37-7497 | Type 7497 Integrated Circuit (F8, H8, JB, K8) | |
| 94 | 37-74LS109 | Type 74LS109 Integrated Circuit {A9) | |
| 95 | 37-74LS139 | Type 74LS139 Integrated Circuit (L3, E4) | |
| 97 | 37-74LS157 | Type 74LS157 Integrated Circuit (F3, H3, J3, K3, F6) | |
| 98 | 37-74LS161 | Type 74LS161 Integrated Circuit (C5, P8) | |
| 99 | 37-74LS164 | Type 74LS164 Integrated Circuit (K9, P9, R9) | ny} |
| 101 | 37-74L8174 | Type 74LS174 Integrated Circuit (N7, P7, D8, N11) | |
| 102 | 37-74LS175 | Type 74LS175 Integrated Circuit (M7) | |
| 103 | 37-74191 | Type 74191 Integrated Circuit (C4) | |
| 104 | 37-74LS191 | Type 74LS191 Integrated Circuit (F5, H5, J5, K5, B7, C7, D7, C9, D9, E9, F9, |
H9, J9)
| 106 | 37-74LS244 | Type 74LS244 Integrated Circuit (B2, C2) |
| 107 | 37-74LS245 | Type 74LS245 Integrated Circuit (R2, E3) |
OR
| 108 | 37-8304B | Type 8304B Integrated Circuit—substitute for item 107 |
| 110 | 37-74LS251 | Type 74LS251 Integrated Circuit (J10, L10) |
| 411 | 37-74LS253 | Type 74LS253 Integrated Circuit (P6) |
| 112 | 37-74LS259 | Type 74LS259 Integrated Circuit (M10) |
| 113 | 37-74L8273 | Type 74LS273 Integrated Circuit (F7, H7, J7, K7) |
| 414 | 37-74LS367 | Type 74LS367 Integrated Circuit (H6, J6) |
| 116 | 37-74LS393 | Type 74LS393 Integrated Circuit (B84, D5) |
| 117 | 37-74LS399 | Type 74LS399 Integrated Circuit (A10, B10, C10, D10, E10, F10) |
| 119 | 37-74LS670 | Type 74LS670 Integrated Circuit (F4, H4, J4) |
OR
| 120 | 37-74LS170 | Type 74L$170 Integrated Circuit— substitute for item 119 | |
| 122 | 37-LM324 | Type LM324 Integrated Circuit (L8, P11) | 4 |
| 124 | 37-555, | Type 555 Timer Integrated Circuit (MB, N8, L9, R10) | : |
| 126 | 37-566 | Type 566 Function Generator Integrated Circuit (P10) | |
| 127 | 37-4016B | Type 4016B Integrated Circuit (M9, N10, R11, B12, D12) | |
| 428 | 37-TLO82CP | Type TLO82CP Integrated Circuit (A12, C12) | |
| 129 | 37-AD561J | Type AD561J Integrated Circuit (B11, D11) | |
| 132 | 37-7805 | 5V Voltage Regulator | |
| 133 | 37-7812 | 12V Voltage Regulator | |
| 134 | 37-7815 | 15V Voltage Regulator | |
| 135 | 37-7915 | 15V Voltage Regulator | |
| 137 | 38-MV5053 | Type MV5053 Light-Emitting Diode (CRS5) | 4 |
| 139 | 41-3003 | 100 uH, +5%, Hot-Molded Plastic Fixed A.F.Choke (L1-13) |
Figure 16 Asteroids Game PCB Assembly, continued a Parts List
| item | Part No. | Description (Reference Designations and Locations in Bold) |
Se ———_——
| 144 | 62-001 | SPST Pushbutton Switch (A6) |
| 142 | 66-118P1T | 8-Station Single-Throw, Dual-Inline-Package Bit Switch (R6) |
| 144 | 79-42C40 | 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C3) |
| 146 | 81-4302 | Nylon Snap-In Fastener |
| 148 | 020670-01 | Test Point |
| 150 | 90-102 | 12.096 MHz, +.005%, Crystal (¥1) |
| 151 | 90-6013 | Microprocessor (C3) |
| 152 | 90-7033 | Random-Access Memory (D2, E2, M4, N4, P4, R4) |
| 165 | 034602-01 | Programmable Read-Only Memory (C8) |
| 167 | 035127-01 | Read-Only Memory (N/P3) |
OR THE FOLLOWING TWO ITEMS:
| 159 | 035129-01 | Programmable Read-Only Memory, MSB—substitute for half of item 157 (K4) |
| 159 | 035130-01 | Programmable Read-Only Memory, LSB—substitute for half of item 157 (L4) |
Memory Components and Their Equivalents (Locations Shown in Bold)
-01 P.C. Boards Alternate -01 P.C. Boards -02 P.C. Boards
- (PROMs) (PROMs) (ROMs) 035131-01 J2 035150-01 J2 035132-01 N2 035143-01 C1 035137-01 Ki
038138-01 N41 wesw we
038134-01 M2
03573901 Jt
035140-01 M1
035136-01 F2
03513601 L2
03614101 HA
03514201 Li a 035153-01 K1
035151-01 H2
- 036144-01 D/E1
035154-01 J1
03515201 F2
035145-01 F1
035155-01 H1
SSA PHONR VOOR
Asteroids.
Figure 17 Regulator/Audio PCB Assembly A034485-01 D
Figure 17 Regulator/Audio PCB Assembly Parts List
| item | Part No. | Qty. | Description (Ref. Designations in Bold) |
| 2 | 10-51P0 | 2 | 1 Ohm, + 5%, ‘4W Resistor (R10, 19) |
| 3 | 10-5100 | 2 | 10 Ohm, + 5%, ‘4W Resistor (R11, 20) |
| 4 | 10-5330 | 1 | 33 Ohm, + 5%, %W Resistor (R3) |
| 5 | 10-5101 | 5 | 100 Ohm, + 5%, YW Resistor (R4, 12, 17, 18, 22) |
| 6 | 10-5271 | 1 | 270 Ohm, + 5%, %W Resistor (R1) |
| 7 | 10-5102 | 1 | 1K Ohm, + 5%, YW Resistor (R2) |
| 8 | 10-5272 | 1 | 2.7K Ohm, + 5%, 44W Resistor (R23) |
| 3 | 10-5752 | 1 | 7.5K Ohm, + 5%, @W Resistor {R7) |
| 10 | 10-5103 | 2 | 10K Ohm, + 5%, %W Resistor (R13, 14) |
| an | 10-5392 | 1 | 3.9K Ohm, + 5%, “@W Resistor (Ré6) |
| 13 | 11-6221 | 2 | 220 Ohm, + 5%, VeW Resistor (R9, 21) |
| 15 | 12-52P7 | 1 | 2.7 Ohm, + 5%, 1W Resistor (R5) |
| 16 | 19-100P1015 | 1 | -1Ohm, + 3%, 7W Wirewound Resistor (R24) |
| 17 | 19-315102 | 1 | 1K Ohm Vertical PCB-Mounting Cermet Trimpot, Bournes Series |
3352V-1-1K (R8)
| 20 | 24-250106 | 2 | 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C6, 15) |
| 22 | 24-250477 | 3 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, |
12)
| 23 | 24-250108 | 3 | 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C9, 10, |
13)
| 25 | 27-250103 | 2 | .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) | |
| 26 | 27-250104 | 2 | 1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, C11) | |
| 27 | 27-250224 | 2 | .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (CB, 17) | |
| 29 | 27-250102 | 3 | .001 yf Ceramic-Disc 25V Radial-Lead Capacitor (C2, 7, 16) | |
| 31 | 31-A14F | 2 | 50V 2.5A Miniature Axial-Lead High-Current Rectifier | (CR1, CR4) |
| 32 | 31-1N4001 | 2 | SOV Silicon Rectifier 1N4001 Diode (CR2-3) | |
| 34 | 33-TIP32 | 1 | PNP Power Transistor, Type TIP32 (Q2) | |
| 35 | 34-2N3055 | 1 | NPN Silicon Transistor, Type 2N3055 Q3) | |
| 36 | 34-2N3904 | 2 | NPN Silicon Transistor, Type 2N3904 (Q4, 6) | |
| 38 | 37-LM305 | 1 | 5V Linear Voltage Regulator (Q1) | |
| 39 | 37-TDA2002A | 2 | Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q35, 7) | |
| 44 | 79-58008 | 1 | 9-Position Connector Receptacle (J7) | |
| 45 | 79-58092 | 1 | 6-Position Connector Receptacle (J6) | |
| 46 | 79-58059 | 1 | 4-Position Connector Receptacle (J8) | |
| 47 | 79-20230 | 19 | Female PCB-Mounting Terminal | |
| 48 | 034531-01 | 4 | Heat Sink | |
| 49 | 72-1608C | 4 | #6-32 x V2" Cross-Recessed Pan-Head Corrosion-Resistant Steel |
Machine Screw
| 50. | 76-995 16 | 7 | #6-32 Nut/Washer Assembly |
| 51 | 75-056 | 7 | #6 Internal-Tooth Steel Lock Washer |
| 52 | 020670-01 | 6 | Test Point |
| 53 | 75-F60805 | 3 | #6-32 x 2” Binder-Head Nylon Screw |
| 57 | 78-16008 | 1 | Thermally Conductive Compound for the 2N3055. |
| 58 | 78-16014 | 3 | Thermally Conductive Compound for TDA2002A and TIP32 |
| 60 | §2-003 | 2 | Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper |
Wire with .6” Centers
| 61 | 52-004 | 2 | Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper |
Wire with .3" Centers
TOP VIEW
(ing) 3 ReaD @
BOTTOM VIEW
Figure 18 Power Supply Assembly for X-Y Games A034561-01 B
Figure 18 Power Supply Assembly for X-Y Games “*S e Parts List
| item | Part No. | Qty. | Description |
| A | A034955-01 | 1 | Power Supply Sub-Assembly, Rev. A, consisting of the following 17 items: |
| 4 | 034482-01 | 1 | Base for Power Supply Chassis |
| 2 | 79-4411006 | 1 | Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post |
| 3 | 79-3206 | 1 | §-Position 3AG Fuse Block with %" Quick-Disconnect Terminals |
| 4 | 46-2017002 | 3 | 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse |
| 5 | 46-2013002 | 3 | 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse |
| 6 | 29-053 | 1 | 26,000 uf 15V Electrolytic Capacitor |
| 7 | 78-70501SC | 1 | 2" Diameter Capacitor Mounting Bracket |
| 8 | 79-15021001 | 1 | 2-Circuit Single-Row Terminal Block |
| 9 | 78-2708 | 41 | Nylon Type 6/6 Hole Bushing with 5/8" Inside Diameter x 55/64" Outside |
Diameter x 4” Thick
| 10 | A006555-01 | 1 | Rectifier Printed Circuit Board Assembly |
| W | 72-HA4804S | 3 | #8-32 x V4" Cross-Recessed Pan-Head Zinc-Plated Stee! Thread-Rolling |
Tri-Fluted “Taptite” Screw
| 12 | 72-HA4812S | 1 | #8-32 x 4” Cross-Recessed Pan-Head Zinc-Plated Stee! Thread-Rolling |
Tri-Fluted “Taptite” Screw
| 13 | 72-1008F | 2 | #10-32 x 4" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fluted “Taptite” Screw
| 14 | 72-HA4606S | 4 | #6-32 x 3/8" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fluted “Taptite” Screw
| 15 | 75-0108 | 2 | #10 Flat Plain SAE-Standard Zinc-Plated Steel Washer | |
| 16 | 75-0188 | 4 | #8 Flat Plain SAE-Standard Zinc-Plated Steel Washer | |
| 17 | 75-99518 | 1 | #8-32 Nut/Washer Assembly | |
| B | A034630-01 | 1 | RFI Filter Assembly | |
| e | Cc | A034629-01 | 2 | A.C. Harness Assembly |
| D | A034623-02 | 1 | Power Supply Harness Assembly (for X-Y Games) | |
| E | 034544-01 | a | Fuse Block Cover | |
| F | 75-0188 | 4 | #8 Flat Plain SAE-Standard Zinc-Plated Steel Washer | |
| G | 75-99518 | 4 | #8-32 Nut/Washer Assembly | |
| H | 72-HA4812S | 2 | #8-32 x 3/4" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling |
Tri-Fluted “Taptite” Screw
AL. PERSONS RECEIVING THs DRAWING Fe jaroidaen without me
(@) AJR, 3 Pics —BN & BN
Figure 19 Main Harness and Component Assembly A035158-02 A
| Hem | Part No. | Description |
| 1 | A035157-01 | Main Harness Assembly |
| 2 | A034631-01 | On/Off Switch Assembly |
| 3 | 68-002 | Interlock Switch (2 per game) |
| 4 | 000268-02 | Interlock Switch Mounting Bracket |
| 5 | A030169-01 | Volume Control/Test Switch/Bracket Assembly |
Figure 20 Fluorescent Light Assembly A034752-01 A
| ttem | Part No, | Description |
| 1 | A005493-01 | Fiuorescent Light Harness |
| 13 | 93-113 | 18” Fluorescent Lamp Fixture with Starter |
| 14 | 79-561816 | Spring Connector Wire Nut for 16- to 18-Guage Wires |
| 15 | 78-2652 | Rubber Grommet with 5/8” Inside Diameter x 1 1/8" Outside Diameter x 5/16” |
Thick—for 7/8” Diameter Sheet-Metal Holes Lo
26 ard
- 2PLCS © 2PLCs (6 28) 6 PLCS
- 2PLCS 13 25 21) 2PLCS
- 15) 2PLCS 34 ° 2 9) 2PLCS
32 6 42 8 3 11 6
- aPLes N
- 2PLCs 2)2PLcs (24) 2PLes COMB ERAT Bape Seee ane SPAIN, pennies. Ate “SU5h ale 4) 2PLcs Not shown:
- 2PLCS ()2 Pies
- 4PLCS s006921-01 epeeen Harness Assy. atte Unless by ar ter agreement pert sgicm trom sae coroorat a Figure 21 Coin Door Assembly A006794-16 thru -28 K
Figure 21. Coin Door Assembly Parts List
| fem | Part No. | Qty. | Description |
| 1 | A007637-16 | Front Bezel Assy.—Used only on -16 Coin Door Assy. (25°) | |
| A007637-17 | t | Front Bezel Assy.—Used only on -17 Coin Door Assy. (5 Fr) | |
| A007637-18 | fo! | Front Bezel Assy.—Used only on -18 Coin Door Assy. (1 DM) | |
| A007637-19 | ue | Front Bezel Assy.—Used only on -19 Coin Door Assy. (4 Kr) | |
| A007637-20 | Bo | Front Bezel Assy.—Used only on -20 Coin Door Assy. (+00 Y) | |
| A007637-21 | g = | Front Bezel Assy.—Used only on -21 Coin Door Assy. (10 pence) | |
| 4A007637-22 | x3 | Front Bezel Assy.—Used only on -22 Coin Door Assy. (20¢ |
ag Australian)
| A007637-23 | Sc | Front Bezel Assy.—Used only on -23 Coin Door Assy. (1 DM/2 DM) |
| A007637-24 | 73 | Front Bezel Assy.—Used only on -24 Coin Door Assy. (1 Fr) |
| A007637-25 | ° | Front Bezel Assy.—Used only on -25 Coin Door Assy. (1 Baht) |
A007637-26 Front Bezel Assy.—Used only on -26 Coin Door Assy. (1 DM/5 DM) A007637-27 Front Bezel Assy.—Used only on -27 Coin Door Assy. (100 Lire} A007637-28 Front Bezel Assy.—Used only on -28 Goin Door Assy. (25¢/U.S. $1 coin) For breakdown of Front Bezel Assy., see Figure 22
| 2 | 72-HA4608C | 3 | #6-32 x 2" Cross-Recessed Pan-Head Cadmium-Piated Steel Tri- |
Fluted Thread-Rolling Screw
| 3 | A030362-01 | 1 | Coin Lockout Assembly |
| 4 | A030260-01 | 2 | Coin Switch Assembly |
| 5 | A002465-01 | 1 | Coin Counter Assembly |
| 6 | 004320-01 | 1 | Coin Door Weldment |
| 8 | 004344-01 | 1 | Key Loop |
| 9 | 004340-01 | 2 | Spring Return (used only on German DM coin doors) |
| 10 | 004337-01 | 2 | Bracket for Lock-Out Wires |
| an | 004338-01 | 1 | Right-Hand Lock-Out Wire |
| 12 | 004336-01 | 41 | Left-Hand Lock-Out Wire |
| 13, | 004326-01 | 2 | Scavenger Button |
| 15 | 006904-01 | 2 | Spacer (used only on German DM coin doors) |
| 46 | 030257-01 | 1 | Lamp Socket |
| 17 | 70-11-47 | 1 | NEMA #47 Incandescent Miniature Bayonet-Base Lamp |
| 18 | 73-3008 | 2 | Carbon Spring Steel External Retaining Ring, for 4%" Diameter Shaft |
| 20 | 72-HA4604C | 2 | #6-32 x 14" Cross-Recessed Pan-Head Cadmium-Plated Steel Tri- |
Fluted Thread-Rolling Screw
| 21 | 75-99516 | 13* | #6-32 Steel Nut and Spring Washer Assembly |
*Quantity of 15 is used on the German DM coin doors
| 22 | 008629-01 | 2 | Spring |
| 23 | 71-2118 | 1 | Cam Lock, Hudson #CR73A045S |
| 24 | 71-1225CU | Coin Mechanism for American Quarter | |
| 71-1205FF | n | Coin Mechanism for French 5-Francs Coin | |
| 71-1201MG | Q | Coin Mechanism for German 1-Mark Coin | |
| 71-1201KS, | ose | Coin Mechanism for Swedish 1-Krona Coin | |
| 71-12100YJ | aos | Coin Mechanism for Japanese 100-Yen Coin | |
| 71-1210PE | Boo | Goin Mechanism for English 10-Pence Coin | |
| 71-1220CA | €5 > | Coin Mechanism for Australian 20-Cent Coin | |
| 71-1202MG | age | Coin Mechanism for German 2-Mark Coin | |
| 71-1201FF | ace | Coin Mechanism for French 1-Frane Coin | |
| 71-1201BT | 1& | Coin Mechanism for Thai 1-Baht Coin | |
| 71-1205MG | & | Coin Mechanism for German 5-Mark Coin |
71-42100LI Coin Mechanism for Italian 100-Lire Coin 71-1201ADU Coin Mechanism for U.S. $1.00 Coin
| 25 | 007753-01 | 1 | Anti-Probe Plate |
| 26 | A007638-01 | 1 | Slam Switch Assembly |
| 27 | 75-0368 | 4 | #6 Flat Plain SAE-Standard Zinc-Plated Steel Washer |
| 28 | 73-3025 | 6 | Carbon Spring Steel External Retaining Ring, for 0.184” Diameter |
Shaft
| 30 | 75-056 | 1 | #6 Internal-Tooth Zinc-Plated Steel Lock Washer | |
| ® | 32 | 033368-01 | 1 | Lock Bracket |
| 33 | 033369-01 | 1 | Lock Arm | |
| 34 | 033371-01 | 1 | Slam Switch Insulator |
NOTICE TO ALL PERSONS CONFIDENTIAL Rearon
Figure 22 Front Bezel Assembly A007637-16 thru -28 J Parts List
| item | Part No. | Qty. | Description |
| 1 | 004328-02 | 1 | Bezel |
| 2 | 004330-02 | Ring for American Quarter | |
| 004330-02 | + | Ring for French 5-Franc Coin | |
| 009153-02 | = | Ring for German 1-Deutschmark Coin | |
| 004330-02 | BO | Ring tor Swedish 1-Krona Coin | |
| 009153-02 | as | Ring for Japanese 100-Yen Coin | |
| 007752-02 | oF | Ring for English 10-Pence Coin | |
| 007752-02 | a8 | Ring for Australian 20 Coin | |
| 030677-02 | 3 7 | Ring for German 2-Deutschmark and U.S. $1.00 Coins | |
| 009153-02 | g g | Ring for French 1-Franc Coin | |
| 030677-02 | a | Ring for Thai 1-Baht Coin | |
| 007752-02 | { | Ring for German 5-Deutschmark Coin |
030677-02 Ring for Italian 100-Lire Coin
| 3 | 004331-02 | 2 | Coin Shield |
| 4 | 004332-02 | 2 | Primary Coin Chute |
| 5 | 004327-01 | 2 | Scavenger Button Bearing |
| 6 | 004329-01 | 2 | Price Plate Clamp |
| 7 | 004343-01 | Price Plate—25¢ | |
| 004343-06 | 4 | Price Plate—5 FR | |
| 004343-04 | 9 | Price Plate—1 DM | |
| 004343-03 | Bo | Price Plate—7 KR | |
| 004343-05 | oo | Price Plate—* 100 | |
| 004343-02 | os | Price Plate—10 P | |
| 004343.07 | 28 | Price Plate—20¢ Australian | |
| 004343-08 | Ro | Price Plate—Einwurf 1 DM/2 DM | |
| 004343-09 | S& | Price Plate—7 FR | |
| 7 | 004343-10 | g | Price Plate—1 Baht |
004343-14 Price Plate—Einwurf 1 DM/5 DM 004343-12 Price Plate—700 Lire 004343-13 Price Plate—25¢/$1
| 8 | 73-3009 | 2 | Carbon Spring Steel External Retaining Ring, for 3/8” Shaft Diameter |
| 9 | 72-1604S | 3 | #6-32 x 14” Cross-Recessed Pan-Head Cadmium-Plated Steel |
Machine Screw
| 10 | 75-046 | 2 | #6 Corrosion-Resistant Steel Split Lock Washer |
| W | 72-CL606 | 6 | #6-32 x 3/8" Phillips Pan-Head Steel “Rolok” Self-Threading, |
Thread-Rolling Machine Screw
| 13 | 75-056 | 1 | #6 Internal-Tooth Zinc-Plated Steel Lock Washer |
408/745-2000 * TELEX 35-7488