Dark Adventure
Devil World (Konami, 1987) · Document · 8 pages · 13 sections · original scan
ae KONAMI
DARK ADVENTURE
DARK ADVENTURE: SUB HARNESSES
CN3
ap
CONTROLS
WsT)
cNs
SPEAKER
OUTPUT
(ST) | 3 | [4 | COIN 3
3P LEFT
3P RIGHT
3P UP
3P DOWN
3P JUMP/START
3P ATTACK
3P DYNAMITE
COIN COUNTER 3
GROUND
SPEAKER +
SPEAKER —
SPEAKER —
SPEAKER + RED
WHITE/RED
WHITE/YELLOW
WHITE/BLACK
WHITE/BLUE
WHITE/BROWN
WHITE/ORANGE
WHITE/GRAY
BLUE
BLACK
WHITE
BLACK
BLACK
GRAY
DARK ADVENTURE: AC FLOW CHART
- GREEN/YELLOW
- BLACK
- RED 4, BLUE
- BROWN
- RED/BLACK
- BLACK/WHITE
- WHITE
- GREEN
- VIOLET
- ORANGE LINE CORD
NOISE FILTER
FLOURESCENT LAMP:
DIP SWITCH SETTINGS
DIP SWITCH NO. 1 SETTINGS DIP SWITCH NO. 2 SETTINGS
| sw | 4 | ie | THE NUMBER OF THE PLAYER'S LIFE | |||||
| + | oFF | oFF | OFF | OFF | 1 | 1 | 1 | 3 | NUNBER | ||
| ON | _|_OFF | 1 | 7 | OFF | OFF | 2 | ||
| OFF | ON | 1 | 3 | » | [on | OFF | 3 | ||
| ON | ON | 1 | 4 | OFF | ON | 5 | |||
| OFF | OFF | ON | OFF | 1 | 5 | ON | ON | 7 |
| ON | OFF | 1 | & | *The number of players life multiplied by the number of | ||||
| OFF | ON | 1 | 7 | credit makes the number of players life for a play | |||
| ON | ON | 2 | 1 |
DIFFICULTY OF THE GAME
| Sey" | = | 2 | 8 | sw | 6 | 7 | | | DIFFICULTY |
| ON | OFF | . | 5 | OFF | OFF | EASY | |||
| OFF | ON | 3 | 1 | + | | on | OFF | NORMAL | ||
| ON | ON | 3 | 2 | OFF | ON | DIFFICULT | |||
| OFF | OFF | ON | ON | 3 | 4 | on | ON | VERY DIFFICULT | |||
| ON | OFF | 4 | 1 | |||||
| OFF | ON | 4 | 3 | SOUND | ||||
| on | ON | INVALID | sw | 8 | SOUND |
OFF OFF + | ON ON DIP SWITCH 1
ON SW5 through
| OFF | lo felelelele|ele| | SW8 are not used. | DIP SWITCH 2 | ||
| 12345678 | ON | ° | ° | * | SWS through |
| OFF | . | . | SW5 are not used. |
DIP SWITCH NO. 3 SETTINGS
- VIDEO SCREEN FLIP
| SW | 1 | FLIP |
| ° | OFF | NORMAL |
ON UPSIDE DOWN
2, CHANGE OF MODE
| SW | 3 | MODE |
| . | OFF | GAME MODE |
ON CHECK MODE
DIP SWITCH 3 ON SW2 and OFF elelele SW4 are not used. 12345678
SELF TEST
A. How to start.
- Turn on the SW3 of the DIP SW3. B. Test Items. Color Conditioning. Control Check. Coin Counter Check. DIP SW SET. Sound Check. Video Screen Flip. PaPRono
*To change items, push MAP button, *Push 1P SHOOT (JUMP, START) button to change sound.
DARK ADVENTURE: WIRING DIAGRAM
POWER
SUPPLY
Ld +5V_ 7 12v_2A
COLOR or MONITOR [mie |__| [smc |
+12v
COIN COUNTER
COIN INS
SELECTOR ao 1A
Al
SAME AS 1P CONTROLS =~ 12¥ REQUIRED POWER CAPACITY. COMPONENT SIDE
CONTROL FOR 3P
SAME AS 1P CONTROLS
L_ CONTROL FOR 2
a TLovnamite TTACK >/START TIGHT
CONTROL FOR 1P
AMdNI Y3AOd oNI SC HA-Sd98 YOLI3NNOD HA
9M 1d YOLI3NNOI NIG dé9 TNO
PCB(B) CRT BOARD
9N71d YOiT3NNOD NIG db9 2ND ‘SOLDER SIDE Sennen ours nev ‘j 4P_Ne CONNECTOR, TEREO a BaP-SHF-1AK JST 2 [lel ellelss EEE Pano Seen wo a+99
| RIGHT | 2828 a uERS * | ERSs |
au ese GEs8E2g9 2% 23° SE°2S52 © <2 6x0 ce 0 WE FS8E 6g Se
| ancy | (YY bo | a3 | Ge 282 | |
| {-—+ | 9 oo | age | =" &§ gs | |
| (—t | +5V | 8 | * | e588 |
-—P a «sy 32 +5v 3
| LEFT | aa | DL] +8v | Re |
Zs
| Ff | an | 7 | |
| i | +12¥ | = ert | nq |
F] +e 5 i te] COIN COUNTER! 2 [=] coin countere 2
| Cr | wo | 8 |
K_] GND z 10, 5 (it g iM 2
| CI | ara RED | 8 |
Ps oreen z
BLUE ad
| =} src | PCB(A) | a |
14 VIOEO GND R SERVICE 1P
ats CPU BOARD
3P_DYNAMITE (ie [ _ cor ["3atrack J tT] cone [~3P_ouNP/STaRT J 17 MAP/START farmer 4)
| ‘3P_LEFT | 18 | 1P UP | |
| PP | —V_] 2° up | g | |
| 3P_DOWN | 18 | 1P DOW, | ~ |
| GND | 2P DOWN | 2 |
(tot 1P LEFT x
| a] | x_} 2P LEFT | g |
| 2 | 1P RIGHT | = |
y 2P RIGHT 8 1P JUMP/START Zz aD Z 2P QUMP/START bal 1P ATTACK =
| 2P_DYNAMITE | @) 2p ATTACK | JAMMA | Ed |
PAT.
| 2P ATTACK | L24. | (P DYNAMITE | SGPIN EDGE CONNECTOR | g |
| ‘2P_JUMP/START. | DJ 2P DYNAMITE | a | ||
| ‘2P_RIGHT | yet | 5/32 INCH PITCH | g | |
| 2P LEFT | [+= | bal |
DoW are
| GND | GND | ons |
=
| 5 | og | EXTENSION 1/0 |
(71 on CONNECTOR MAP/START SW T 4 | Map/START 1 lias 1 OYNAMITE it ° 8 AP ATTACK i [iP oowrsTeT
| 1P RIGHT | GND | “WOTE- =) 1P-NO.1 PLAYER | 4 SURGE KILLER DIeDES |
| LET | 2 2P NO.2 PLAYER | FOR COIN COUNTER | |
| COIN! | 3 3P NO.3 PLAYER | INSTALLED 6N P.C.B |
1P UP cOIne 1P_ Down
Gold Mech: Service Information
CLEANING and CARE of the MECHANISM
The magnet that is fitted to the mechanism, should be kept clean from foreign particles. The magnet can be cleaned by swinging the gate open. (as shown in Fig. 1). Remove metal filings from the magnet by guiding the point of a screwdriver along the edges of the magnet, such that the filings cling to the screwdriver.
The mechanism can be cleaned by immersing in water using a small brush to clean the mechanism. Rinse the mechanism with boiling water and dry with compressed air.
If the above procedures are not successful, check for worn, bent or damaged parts and replace where necessary.
Coin switch The coin switch comes in two different spring tensions—identified by the color of the plastic boss at the wire’s pivot point.
Red: Light tension—U.S. 25¢
White: Heavy tension—heavy foreign coins Removal of Mechanism
To remove the coin selector: Unscrew the two screws (as shown in Fig. 2)—swing rear of selector body away from the lock-out side and withdraw.
The Gold Mech Accepiors are designed to require a minimum of maintenance and field adjustment. Coins are checked by diameter and thickness, weight, metal content, bounce, and for ferromagnetic coins such as nickel and steel, a rim test is also used.
Fig. 3
The Magnet
Coins that are too thick will fail to pass between the magnet and the backplate of the mechanism; and will be cleared by the magnet wiper when the reject lever is actuated. (Fig. 3)
Gold Mech Engineering Data and Parts List
91-3009-00
91-3022200 ee
~————9 1-3002-00 91-301 1-00
91-3029-00 \ ; 91-3023-00. \:
91 eon
91-3013-00 91-3026-00
91~3001-00
Ts @-—91-1036-00 LO ~%: 90-1030-00 91-3028-00 { 91-3017-00
91-3008-00
PARTS LIST
| 90-1030-00 Retaining Screw (#6-32” x .250") | 91-3009-00 Gate | 91-3023-00 Locknut-Magnet Holder |
| 91-1036-00 Mounting Stud | 91-3011-00 Cradle | 91-3024-00 “Screw-Magnet Holder |
| 91-3001-00 Back Plate | 91-3013-00 Magnet Holder with Magnet | 91-3025-00 Screw Separator |
| 91-3002-00 Reject Lever | 91-3016-00 Gate Spring | 91-3026-00 Washer |
| 91-3003-00 Reject Lever Spring | 91-3017-00 Gate Pin | 91-3028-00 Cotter Pin for Anti-Stringing Device |
| 91-3006-00 Cover Plate | 91-3019-00 Separator | 91-3029-00 E-Clip for Cradle |
91-3008-00 Anti-Stringing Device 91-3022-00 Diameter Adjustment
TOP VIEW
MOUNTING STUDS FITTED UPON REQUEST
- 3 HOLES (EACH SIDE) FOR | Lao: . MOUNTING STUDS IF REQUIRED CoN FSoum 6-32 SCREW OUTLET
COMPLETE COIN DOOR ASSEMBLY
EXPLODED VIEW
“TS oo 100-00 * J
91-1103-00:
91-1122-00—_—-
4117-00 . 91-1116-00
91-1144-00———~,
‘90-1207-00——=
PARTS LIST 12-4050-01 S-10 Acceptor Body IS 258 12-4050-03 $-10 Acceptor Body Canadian 25° 20-4177-00 Plastic Cash Box 20-4179-00 Stee! Enciosure 22-1400-00 Locking Bar 24-1150-00 Wire Harness 90-1000-00 Keyhock Bezel Screw 90-1001-00 Bezel Screw 90-1002-00 Hinge Screw 90-1003-00 Ciamp Screw 90-1007-00 Flat Head Microswitch Mounting Screw 90-1008-00 Panhead Microswitch Mounting Screw L ~ ~ J
91-1127-00 91-1104-00 ! 01-1 141-00
91-1120-00
1108-00
91-1107-00
0-1007-00/
90-1102-00 Washer for Bezel Screw 90-1207-00 Nut for Microswitch Mounting Screw 90-1300-00 Keyhock 91-0502-00 Zinc Die Cast Frame 91-0503-00 Lower Door 91-0504-00 Upper Door 91-0505-00 Round Lock and Cam Assembly 91-0506-00, Clamp 91-0515-00 Flat Lock and Cam Assembly 91-0535-00 Flat Lock and Cam Assembly 91-0545-00 Round Lock and Cam ‘Assembly wr
91-1125-00
91-1193-00 Coin Inlet Lamp Side 91-1104-00 Coin Inlet Cover Side 91-1105-00 Reject Cup Side Plate 91-1106-00 Reject Cup Base Plate 91-1 107-00 Microswitch Bracket 91-1 108-01 Lockout Flap US 25* 91-1109-00 Reject Flap 91-1110-00 Metal Switch Adjuster 91-1111-00 Black Button Bezel 91-1112-00 Black Reject Bezel 91-1113-01 Entry/Reject Button JS 25° 91-1116-00 Microswitch (Black End Arm) 91-1117-00 Lampholder 91-1118-00 6 Volt Wedge Base Lamp 191-0538-00
91-4149-00 Button Spring 91-1120-00 Lockout Spring 91-1122-00 Retaining Screw for ‘Acceptor Body 91-1125-00 Clear Plastic Cover for Microswitch 91-1127-00 Plastic Switch Adjuster 91-1141-00 Base Plate With Pivot and Stud 91-1144-00 6 Volt DC Lockout Coil Assembly 91-1211-00 Zinc Plated Button Bezel 91-4212-00 Zinc Plated Reject Bezet