CATHODE RAY TOMES

World Series 99 UPRIGHT

World Series '99 (Sega Enterprises, Inc. USA, 1999) · Manual · 53 pages · 26 sections · original scan

Page 1

1ST PRINTING JULY 99

SEGA

OWNER’S MANUAL

SEGA ENTERPRISES, INC. USA

MANUAL NO. 999-0813

Page 2

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL

GENERAL PRECAUTIONS

. PRECAUTIONS TO BE HEEDED FOR OPERATION

. NAME OF PARTS

. ACCESSORIES

. ASSEMBLY AND INSTALLATION

. PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE

. EXPLANATION OF TEST AND DATA DISPLAY

6-1 COIN METER SWITCH UNIT

6-2 TEST MODE

6-3 GAME TEST MODE

6-4 INPUT TEST

6-5 SOUND TEST

6-6 GAME ASSIGNMENTS

6-7 VOLUME SETTING

6-8 BOOKKEEPING

6-9 BACKUP DATA CLEAR

  • COIN SELECTOR
  • MONITOR

8-1 CAUTIONS CONCERNING SAFE HANDLING OF MONITOR

8-2 CLEANING THE CRT SURFACES

8-3 ADJUSTMENT METHOD

  • REPLACEMENT OF FLUORESCENT LAMP

9-1 REPLACEMENT OF FLUORESCENT LAMP

  • PERIODIC INSPECTION TABLE
  • TROUBLESHOOTING
  • CONTROL PANEL/BAT MECHA,
  • GAME BOARD

13-1 REMOVING THE GAME BOARD

13-2 COMPOSITION OF THE GAME BOARD

  • DESIGN RELATED PARTS
  • PARTS LIST
  • WIRING DIAGRAMS wns

Dune

19~20

21~23

24~26

24~25

30~31

33~44

XXX

Page 4

SPECIFICATIONS

Installation space: 35 in.(L) x 32 in. (W)

Height: 81 in.

Weight: Approx. 430 lbs.

Power maximum current: 2.31 Amp AC 120V 60 Hz

MONITOR: 29” NANAO MONITOR

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to the WORLD SERIES ‘99, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 415-701-6580 Fax 415-701-6594 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 5

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 6

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’ s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below:

  • Places subject to rain/water leakage, or condensation due to humidity;
  • In close proximity to a potential wet area; + Locations receiving direct sunlight; + Places close to heating units or hot air; ¢ In the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; + In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
  • Places subject to any type of violent impact; + Dusty places.

INSTALLATION PRECAUTIONS

  • Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.

+ Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.

  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). ¢ For the operation of this machine, secure a minimum area of 32” (W) by 42°(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

SK92

AMUSEMENT MACHINE

Page 7
  • PRECAUTIONS TO BE HEEDED FOR OPERATION

In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION

@ In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can move and cause an accident.

@ To avoid electric shock, check to see if door & cover parts are closed.

WARNING!

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others

CAUTION! and result in injury or trouble.

PRECAUTIONS TO BE HEEDED DURING OPERATION

To avoid injury and accidents, those who fall under the following catagories are not allowed to play the game:

  • Intoxicated persons
CAUTION! * Those who have high blood pressure or heart problems.
  • Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
  • Persons susceptible to motion sickness.
  • Persons whose acts runs counter to the products warning displays.

@ To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in openings of the product or small openings in or around doors.

To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason. Although this product has the accident preventive covering attached to poten-

CAUTION! tially hazardous places where hand and fingers could be caught, small children are unable to perceive hazards. Use care so that small children do not come close to the product when in play. Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage and/or falling down, resulting in injury due to fragments and falling down.
Page 8
  • NAME OF PARTS

MARQUEE

CABINET

CONTROL PANEL

OIN DOOR ASSY

GAME SPECIFICATIONS WIDTH in. LENGTH in. HEIGHT in. WEIGHT Ibs.

Weight-DURING SHIPPING All measurements are and rounded UP ~ 460 LBS.

WHEN ASSEMBLED 32” x 36” x 8" 430 LBS.

Page 9
  • ACCESSORIES

OWNERS MANUAL 999-0813 DESCRIPTION Part No. (Qty.)

Note

Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you. KEY MASTER KEY 220-5576 (2) (2) For opening/closing For the CASHBOX DOOR the doors

0g °38cd

WARNING! A\ THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2, HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD 2, CRAZY TAXI, ZOMBIE REVENGE, STAR WARS TRILOGY, WORLD SERIES ‘99

!!NNEVER SHIP MODEL 3 / NAOMI GAME BOARDS OUTSIDE OF CAGE!!

CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

WARNING! NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.
Page 10
  • ASSEMBLING AND INSTALLATION

A

CAUTION! Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 5-item sequence:

ASSY OF CABINET

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY

ASSY CHECK

Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.
Page 11

1 | ASSyY OF CABINET

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can cause violent

CAUTION! |} falling down accidents.

BILLBOARD PLATE R

® Take out the 3 truss screws from the lower part of the Billboard and pull out the Billboard Case towards you. BILLBOARD CASE.

@ Apply Billboard Plate R to the rear of Billboard Case with double sided tape.

@ Return the Billboard Case to the original position and secure with the 3 truss screws.

@ Take out the 4 truss screws to remove the flat washer used. Lamp Cover B. |

© Insert the Billboard Plate to Billboard Case and secure Lamp Cover B with 4 truss screws.

| oT TRUSS SCREW (4) i LT | M4x12, black, H flat washer used.

Page 12
WARNING! SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the surface. Unless the Adjusters come into contact with the surface, the Cabinet can move of itself, causing an accident.

This machine has 4 each of casters and 4 each of adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

)

@ Move the machine to the installation position.

Cause all of the leg levelers to make contact with the floor. By using a wrench, make adjustments in the height of the leg adjusters to ensure that the machine's position is level.

\ Leg Leveler After making adjustments, fasten the leg adjuster nut upward and secure the height of the leg adjuster.

Page 13

3 | Power SUPPLY

WARNING! @ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. @ Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering.

Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that power switch is off

MAIN SW

To the Power Supply Socket outlet

Page 14

4 | assycHECK

GAME TEST MODE

TEST MENU Bring the arrow to the item of GAME TEST MODE in

the SYSTEM TEST MENU, and press the Test button to

display the TEST MENU peculiar to ZOMBIE RE-

VENGE. INPUT TEST OUTPU i SOUND TEST GAME ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING Press the SERVICE button to move the arrow. Bring the

BACKUP DATA CLEAR arrow the desired item and press the TEST button.

Upon finishing the test, bring the arrow to EXIT and

press the TEST button to return to the SYSTEM MENU

MODE. ->EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

INPUT TEST

This test displays the state of each switch.

If this switch goes ON when activated, it is satisfactory.

Display varies depending on the JOYSTICK TYPE setting in (3) GAME ASSIGNMENTS.

INPUT TEST

1P_START :OFF 1P_ABUTTON :OFF 1P_BBUTTON :OFF 2P_START :OFF 2P_ABUTTON :OFF 2P_BBUTTON :OFF

1P_STICK: (80, 80) IP_BAT : 80 2P_STICK: (80,80) 2P_BAT : 80

PRESS TEST BUTTON TO EXIT

Page 15

SOUND TEST

This allows sound and background used in the game to be checked/ tested.

SOUND TEST

PACKAGEOL PACKAGE02 BGM_PACK AMBIENCE UMPIRE SYSTEM TEAMCALL

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT\

CRT TEST

CRI TEST 12

oe 7 ~~ PRESS TEST BUTTON TO CONTINUE

Fated

PRESS PEST BUTPN TO CDNTING Pressing the service button increase the number by one

and changes the sound.

Press the TEST button to have the MENU return to the

screen.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the projector by refering to Section 9.

Perform the above inspections also at the time of monthly inspection.

Page 16
  • PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

@ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is

WARNING! inserted can damage the power cord and cause a fire or electric shock. As this game has no casters, the Cabinet must be lifted off of the ground in order to be moved. Plural persons are required to lift cabinet safely. Moving the cabinet with the leg still in contact with the floor, or moving the cabinet by ‘rocking’ the cabinet can severly damage the cabinet and the legs. When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

A

CAUTION!

DO NOT PUSH CABINET FROM SIDE. ENSURE CASTERS ARE IN CONTACT WITH FLOOR BEFORE MOVING.

Page 17
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

When performing installation, servicing product or changing game boards refer to individual kit instructions for each of the listed items below:

ITEMS DESCRIPTION

When the machine is installed, perform the following: INSTALLATION | 1. Check to see that each setting is as per standard setting made OF MACHINE at the time of shipment.

  • In the INPUT TEST mode, check each SW and VR.
  • In the OUTPUT TEST mode, check each of lamps.
  • In the MEMORY TEST mode, check ICs on the IC Board.

Choose MEMORY TEST in the MENU mode to allow the MEMORY MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following: SERVICING 1. MEMORY TEST

  • Ascertain each setting.
  • In the INPUT TEST mode, test the CONTROL device
  • In the OUTPUT TEST mode, check each of lamps.

CONTROL 1. In the INPUT TEST mode, check each SW and VR. SYSTEM 2. Adjust or replace each SW and VR.

  • If the problem can not be solved yet, check the CONTROL’s moves!

MONITOR In the MONITOR ADJUSTMENT mode, check to see if the MONITOR adjustment is appropriately made.

IC BOARD 1. MEMORY TEST

  • In the SOUND TEST mode, check the sound related ROMs.

DATA CHECK Check such data as game play time and histogram to adjust the difficulty level, etc

Page 18

6- 1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ [If the COIN METER and the game board are electrically disconnected,

IMPORTANT! game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows:

SWITCH UNIT

(@) SOUND VOLUME Controls the speaker volume of the right/left speakers. SERVICE BUTTON

(2) TEST BUTTON (TEST SW)

For the handling of the TEST BUTTON, refer to the section on test mode.

@) SERVICE BUTTON (SERVICE SW)

Gives credits without registering on the coin meter.

Page 19

6-2 TEST MODE

System Menu. This test mode mainly allows the IC board to be checked for accurate functioning, monitor color to be

adjusted as well as COIN ASSIGNMENTS and GAME ASSIGNEMENTS to be adjusted.

1.) After turning power on, press the TEST button to have the following test item menu displayed.

2.) Press the SERVICE button to move the arrow. Bring the arrow to the desired item and press the TEST button.

SYSTEM MENU

USA VERSION

RAM TEST

JVS TEST

SOUND TEST

SYSTEM ASSIGNMENTS

COIN ASSIGNMENTS

BOOKKEEPING

BACKUP DATA CLEAR

CLOCK SETING

ROM BD TEST

GAME TEST MODE

WORLD SERIES 99

->EXIT

SELECT WITH SERVICE BUTTON

AND

PRESS TEST BUTTON OPERATION REQUIREMENTS OF THIS GAME: In the SYSTEM ASSIGNMENTS, the CABINET TYPE is set to 2 PLAYER(s) and MONITOR TYPE is set to HORIZONTAL.

COIN ASSIGNMENTS intial settings <USA, EXPORT, AUSTRALIA Version> COIN CHUTE TYPE COMMON COIN/ CREDIT SETTING #12

SEQUENCE SETTING OF COIN ASSIGNMENTS SEQUENCE 1: Number of credits required for Game Start. (intial value=1) SEQUENCE 2: Number of credits required for CONTINUE (intial value=!) SEQUENCE 3-8: NOT USED

MEANING OF DISPLAY IN BOOKEEPING (2/2) P1(P2) SEQ 1: Play frequency of Player | (Player 2) P1(P2) SEQ 2: Frequency of CONTINUE by Player | (Player 2) P1(P2) SEQ 3-8: NOT USED

3.) Bring the arrow to the item of Game TEST MODE and press the TEST button to display the GAME TEST MENU

peculiar to ZOMBIE REVENGE. See the next page onward.

4.) Upon finishing the test, bring the arrow to EXIT and press the TEST button to return to the Gam Mode.

CAUTION! point. The contents of settings changes in SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS, and GAME TEST MODE are stored when the test mode is EXITed. If the power is turned off

before EXITing, the contents of setting changes are ineffective. Be very careful of this

6-3 GAME TEST MODE

TEST MENU

INPUT TEST

SOUND TEST

GAME ASSIGNMENTS

VOLUME S! ING

BOOKKEEPING

BACKUP DATA CLEAR

->EXIT

SELECT WITH SERVICE BUTTON

AND

PRESS TEST BUTTON Bring the arrow to the item of GAME TEST MODE in

the SYSTEM TEST MENU, and press the Test button to

display the TEST MENU peculiar to ZOMBIE RE-

VENGE.

Press the SERVICE button to move the arrow. Bring the

arrow the desired item and press the TEST button.

Upon finishing the test, bring the arrow to EXIT and

press the TEST button to return to the SYSTEM MENU

MODE.

Page 20

6-4 INPUT TEST

This test displays the state of each switch.

If this switch goes ON when activated, it is satisfactory.

Display varies depending on the JOYSTICK TYPE setting in (3) GAME ASSIGNMENTS.

INPUT TEST

1P_START :OFF 2P_START :OFF 2P_ABUTTON :OFF 2P_BBUTTON :OFF 1P_ABUTTON :OFF 1P_BBUTTON :OFF

1P_STICK: (80, 80) 1P_BAT : 80 2P_STICK: (80,80) 2P_BAT : 80

PRESS TEST BUTTON TO EXIT The XX value of 1P (2P)_STICK (XX,YY), indicates the

middle value when the STICK is untouched. It indicates

the minimum value when the stick is turned to the right,

and the maximum value when the STICK is turned to the

left. The volume setting is normal if the maximum value

is between 70 and 8F, the minimum value is between 00

and OF, and the maximum between FO and FF.

The YY value of 1P (2P)_STICK (XX,YY) indicates the

middle vlaue when the STICK is untouched. It indicates

the minimum value when the STICK is turned down, and

the maximum value when the STICK is turned up. The

volume setting is normal when the middle value is

between 70 and 8F, the minimum value is between 00

and OF, and the maximum value is between FO and FF.

The value of 1P (2P)_BAT indicates the minimum value when the BAT is untouched (face up) position. It indicates the maximum value when the BAT is rotated about half a turn until it is stopped. The volume setting is normal if the minimum value is between 00 and OF and the maximum value is between FO and FF.

If any value is abnormal, return to the menu screen and take steps described in #4 “VOLUME SETTING”. Then return

to this test and confirm the values.

To return to the menu screen, press the TEST Button while holding the SERVICE Button down.

6-5 SOUND TEST

This allows sound and background used in the game to be checked/ tested.

SOUND TEST

PACKAGEO1 PACKAGE02 BGM_PACK AMBIENCE UMPIRE SYSTEM TEAMCALL

SELECT WITH SERVICE BUTTON PRESS 1 T BUTTON TO EXIT To check them, specify the appropriate item using the

SERVICE Button and press the TEST Button to generate

the sound.

By default, the arrow is located at EXIT.

Page 21

6-6 GAME ASSIGNMENTS

GAME ASSIGNMENTS Allows game difficulty adjustments to be performed/ changed. SELECTION OF DESIRED ITEM GAME DIFFICULTY NORMAL 1.) Press the SERVICE button to move INNINGS 1 CREDIT 2 INNINGS FAVORITE OFF the -> and bring it to the desired item. EXTRA INNING OFF 2.) Press the TEST btuuon to change the ->EXIT seting.

3.) After the device setting is finished, SELECT WITH SERVICE BUTTON AND bring the -> to EXIT and press the TEST PRESS TEST BUTTON TO EXIT button.

(A) INNINGS (FOUR SETTINGS LISTED BELOW This sets the number of innings that can be played in the VERSUS-COM mode. FOUR SETTINGS (listed below)

ICREDIT1 INNINGIf | CREDIT is set, when the game can be continued following
1 CREDIT2 INNINGSthe end of the sixth inning, the remaining three innings can be
1 CREDIT3 INNINGSplayed on one credit.

1 CREDIT ALL INNINGS Allows the player all innings on one credit (B) GAME DIFFICULTY (VERY EASY, EASY, MEDIUM EASY, NORMAL, MEDIUM HARD, HARD, VERY HARD) (C) FAVORITE (OFF, Each team) Sets the favorite team. The favorite team becomes stronger than the other teams The favorite team name is displayed in the advertise. Only one teram can be favored at a time (D) EXTRAINNINGS (OFF, ON) Ebnables or disables the extra innings. When set to ON, the game can be played up to 12 extra innings.

Page 22

6-7 VOLUME SETTING

This page allows yo to adjust the volume settings used for the ANALOG STICKS and BAT MECHA.

PLAYERI STICK-H HMAX (CO) STICK-V HMAX (CO) BAT BMAX (CO)

PLAYER2 STICK-H HMAX (CO) STICK-V HMAX (CO) BAT BMAX (CO)

SAVE AND EXIT >EXIT HMIN (50) HMIN (50) BMIN (OC)

HMIN (50) HMIN (50) BMIN (OC) NOW (80) NOW (80) NOW (OC)

NOW (80) NOW (80) NOW (OC)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON TO EXIT

ADJUSTING THE VOLUME VALUE

For the 1P and 2P ANALOG STICKS, move each from the untouched position to the maximum position vertically and

horizontally.

For the 1P and 2P BATS, pull each from the untouched (face-up) position by about half of a turn until it stops.

Then, with the STICKS and BATS untouched, select SAVE AND EXIT and press the TEST Button to return to the

menu screen. This completes adjustments.

After adjustments, be sure to return to the INPUT TEST mode to verify that the values are normal. If they are not normal, come back to the VOLUME SETTING page and readjust the volume settings. If the normal values are not

recovered after several retries, probably the BAT MECHA is faulty.

Page 23

6-8 BOOKKEEPING

This test mode allows each of the CREDIT/TIME/GAME data to be ascertained. BOOKKEEPING (A) NUMBER OF GAMES GAME REPORT PAGE 1/2 IP, 2P total game playfrequency. (B) SINGLE 1P GAMES NUMBER OF GAMES 0 Displays the total number of games played at 1P side

TRG AOTES4(C) SINGLE 2P GAMES

ae GAMES . . o Displays the total number of games played at 2P side

NUMBER OF CONTINUE 0

1P GAMES0(D) DOUBLE GAMES

2P GAMES 0 Displays the number of games that two players began playing. PRESS TEST BUTTON TO EXIT (E) VERSUS GAMES The SERVICE SWITCH usage frequency. (F) NUMBER OF CONTINUE Displays the number of continued games.. (G) IP GAMES Displays the total number of games played at 1P side (H) 2P GAMES Displays the total number of games played at 2P side.

Press the test button to proceed to the next page.

BOOKKEEPING PLAY TIME (A) VS CPU:

VSCPUCOUNTAVERAGELONGESTSHORTESTDisplays the results of versus_CPU game.
12**H *M **s*H *M **S*H *M **§
34*H eM *S*H *M **S*H *M **§
56*“HM *s“HM *s*H «mM «s | (B) DOUBLE:
7-88HM **S“H *M **S“H *M **SDisplays the results of two-player game.
9-10***H *M #5*H *M **S*H *M **§

DOUBLE

1-2*H *M **S*H *M*H *M **S(C) VERSUS:
3-4“H *M **S*“H *M“H *M **SDisplays the results of versus game.
5-6*H *M *S*H *M*H *M *S
78“H *M *S*H *M*H *M **S
9-10*H *M **S*H *M*H *M **SThe number of items depends on the INNINGS

VERSUS values of GAME ASIGNMENTS. The above

8-9*H *M *S*H *M*H *M **§

examples is for “1 CREDIT 2 INNINGS”. PRESS TEST BUTTON TO EXIT “NODATA” is displayed if there is no applicable data.

Press TEST button to return to Menu screen.

Page 24

6-9 BACK UP DATA CLEAR

Clears the contents of BOOKKEEPING.

BACK UP DATA CLEAR

YES (CLEAR) ->NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON TO EXIT

When clearing bring-> to YES and when not clearing, to NO, by using the SERVICE SW and then push the TEST button.

When clearing has been finished, COMPLETED will be dislayed. Pressing the TEST button will have the MENU return to the screen.

Page 25

7.COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: @) Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.).

16) Remove and cleen smears by using a

soft cloth dipped in water or diluted chemical detergent and then squeezed dry. (@) Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. © _ Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. ©) After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selecting,

IMPORTANT! Insert a regular coin in the normal

working status and ensure that the Selector correctly functions. ©

FIG. Ila

Insert a coin

COIN INSERTION TEST aie

Once a month, when performing the COIN SW gutton pressed TEST, simultaneously check the following: down and check if it is + : : rejected. O Does the Coin Meter count satisfactorily? a O Does the coin drop into the Cashbox correctly? COIN METER O Is the coin rejected when inserted while keeping the REJECT BUTTON is pressed down? FIG. lle

Page 26

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON WORLD SERIES ‘99 COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 Mars 2000 series (FORWARD-MOST POSITION)

HOLE POSITION#2 Mars 2000 series DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 DSI01*

*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls authorized distributors. The part number is 91-4000-01. The Mars stacker can be obtained through an autherized Mars distibutor.

Page 27

I Croyk T [elels R!iN O/N|T/R/O|LIS Ti OiNn ALL alt 1850 HOWARD ST., ELK GROVE EL 60007 (847) 228-1810

+ MARS SERIES 2000 UPSTACKER ADAPTABLE G OVER/UNDER TWO ENTRY COIN DOOR*

PART #DESCRIPTIONCOSTPART #DESCRIPTIONCOSTPART #DESCRIPTIONCOST
1) I2-4060-KX S-10 ACCEPTOR19.5016) 91-1108-16 BEJRCT FLAP NYLON, BLACK = 2.7028) 23-L0UL-00 (2F OC ABTER8.50
I-4150-011 S-7 US 8.2512.00IT) S-HM13-OL ENTRI/REJECT BITTON 25¢4.4523-03-00 4.57 00 WBTER3.50
2) AHITTH0 PLASTIC CASBBOX7.4018) 91-1117-00 LAVPHOLDER1.4023) 90-1082-01 ABTER & LOCKOUT SCREPe)
3) 20-4189-00NCLOSTRE, 2200027.5019) 1-1121-00 B/R BUTTON SPRINGBi30) 22-1400-00 LOCKING BAR7.00
4) 90-1002-00 HINGE SCREBb20) S1-1118-006Y LAMP FRDGE BASE%SL) 90-1019-00 3/4" LOCKTASHER2
5) 90-1003-00 CLAMP SCRET%21) S-C3LL-16 BUTTON BREEL BLACK2.70
6) 90-1017-00 SCREV BRZEL NYLON42) M-1312-16 RRJECT BRZEL BLACK2.70
7) 90-1206-02 H-40 KEP AUPB23) 91-2125-00 127 LOCKOUT COTL ASSEMBLY12.85
8) 90-1300-00 KEYHOOK324) GL-2216-16 NICROSRITCH ASSEMBLY15.00
9) 91-0508-16 FRAME30.00UA) SI-L1L6-16 MICROSPITCE BLACK5.40
10) 91-0506-00 CLAKPAbSL-LLIG-HL MICROSRITCH THITE5.40
$1) 91-0547-00 DOUBLE D Call Lock5.2SI-LLL6-10 MICROSRITCH RED5.40
12) 91-0603-16 BLACK MINT DOOR5.402B) S1-1125-00 WICROSRITCH PLASTIC COVER = 85
13) 91-0604-(6 2 ENTRY UPPER DOOR10.0025) 92-1002-01COT INLET LAMP SIDE1.80
14) 91-4008-099 LOCKOUT BRACKET4.3026) $2-4002-021 COIN INLET COVER SIDE1.80
15) 91-1008-107 RASEPLATE ASSENBLY5.0021) 92-1002-10 HOLD DOTY BRACKET1.50

JAN. 1998 FORM 92-1003-05

Page 28
  • MONITOR
CAUTION! When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector (plug) before starting work. Proceeding the work without following this instruction can cause electric shock of malfunctioning. Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA shall not be liable for any malfunctioning and accident caused by said conversion.

COIL DEMAGNETIZER| @ FOCUS LEAD

SECONDARY SIDE FBT. Approx. (Chassis, sheet metal work, CRT, etc.) Disconnect or unplug 29kV Primary side and secondary side The monitor’s circuit which is divided into the Primary side and secondary side, is electrically isolated. Do not touch the primary side and the secondary side simultaneously. Failing to observe the instruction can cause electric shock, and this is very dangerous. SECONDARY SIDE When making monitor adjustments, use a non- (Chassis, CRT) conductive driver and make adjustment without touching any other part other than the Adjustment V.R. and Knob. Also, be sure not to cause a shortcircuit to the Primary side and the Secondary side. If short-circuited, it can cause electric shock or malfunctioning, which is very dangerous.

High tension Voltage Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor, turn the power off so as not to cause malfunctioning or fire hazard.

2) ANODE CAP PRIMARY SIDE DEMAGNETIZER. REAR PART

c @® ANODE LEAD |_ MAIN BD Approx. 29 kV

(black) Approx. 10 kV

Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavely charged as time elapses, generating high tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are disassembled, what’s charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.

CAUTION! Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversly affect the human body. Installation and removal Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work’s sharp edges, etc. and avoid damaging the insulated portions so as not to cause an electric shock and malfunctioning. (For the name of parts, refer to the above figures.)
Page 29

For the purpose of static prevention, special coating is applied to the CRT face of this product. To protect the coating, pay attention to the following points. Damaging the coating film can cause electric shock to the customers. For the caution to be heeded when clearing, refer to the Section of Periodic Aluminum Foil inspection Table. Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on C.R.T. surfaces. Avoid applying stickers, seals, etc. on the C.R.T. face. Do not remove aluminum foils from the C.R.T. corners. Removing the aluminum foils can cause static prevention effects to be lowered.

CAUTION!

Monitor adjustments have been made at the time of shipment. Therefore do not make further adjustment without a justifiable reason.

CAUTION! Adjusting the monitor which contains high tension parts is dangerous

work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunctioning. When making adjustment, utilize a resinous Alignment Rod. Servicing with bare hands or using conductive tools can cause electric shock.

Page 30

NANAO monitor: 200-—5242-—2 4—0 4 (24K mode)

feel (6) Cfianam Fig Bie °&

@ oO

SANWA monitor: 200-5 2 4 3—2 4 (24K mode)

COROROMCHORCEOMOCROM”

RGAIN GGAIN BGAIN — BRIGHT HSIZE HHOLD HPOS! VSIZE VHOLD VPOSI

R-GAIN

G-GAIN ........ Controls colors.

B-GAIN

BRIGHT........... Controls screen brightness.

H. SIZE ........... Controls horizontal screen size.

H. HOLD ....:.:.. Provides horizontal synchronization, i.e., controls right/left hold.

Controls horizontal display position on screen.

. Controls vertical screen size.

. Provides vertical synchronization, i.e., controls up-down hold.

. Controls vertical display position on screen. BOOELOOSHOSO CONTRAST... Adjusts image contrast.

Page 31
  • REPLACEMENT OF FLUORESCENT LAMP

@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Fluorescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause violent falling down accidents.

CAUTION!

9-1 REPLACEMENT OF FLUORESCENT LAMP

® Take out the 3 Tamperproof screws securing the billboard plex. Remove the billboard plex.

@ Be sure to disconnect all connectors conected to the Marquee assembly before removing the FL fixture and/or performing work.

@) Replace the bulb and reinstall.

| LAMP _COVER A FLATHEAD SCREW (2) _// M4X8, black

FLUORESCENT LAMP 208: LOCAL PURCHASE

Page 32
  • PERIODIC INSPECTION TABLE

The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securley inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with dust as is accumulated can cause a fire or

WARNING! electrical shock. . Periodically once a year, request the place of contact herin stated or the Distrib- @ uter, etc. where the product was purchased from, as regards to the interior cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or short circuit accident. Note that cleaning the interior parts can be performed on a pay-basis.

Item Interval

CABINETCheck Adjuster’s contact with surface.Daily
MONITORCheck Adjustments.Monthly

Cleaning of CRT surfaces. Weekly

COIN CHUTE TOWERCheck COIN SW.Monthly

Coin insertion test. Monthly Cleaining the COIN SELECTOR Monthly

Cabinet surfacesCleaningAs necessary
INTERIORCleaningAnnually
POWER SUPPLY PLUGInspection and cleaingAnnually

CLEANING CABINET SURFACES

If the cabinet is badly stained, use a cloth which is dipped in the chemical detergent liquid diluted with water and then squezzed dry. Do not use thinner, benzine, alcohol or chemical dustcloth as these can damage Cabinet surfaces.

GLASS HOLDER UPPER

TRUSS SCREW (3) M5 X16, black

FRONT GLASS

Page 33
  • TROUBLESHOOTING

Should trouble occur, first check connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation Power is not supplied.

Power supply/voltage is not correct. Plug in correctly

Make sure that power supply/voltage is correct

Irregular sound emitted from inside Cabinet Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter.

The color of the image on PROJ. screen is incorrect. Connector connections are defective. Check the connection for the RGB and SYNC connectors of the PROJ. TERM. BD and VPM BUFFER BD.

screen has color deviation. The image on PROJ. Affected by the magnetic field of installation location. Make CONVERGENCE adjustment. (Refer to Section 12.)

No sound is emitted. Sound Volume adjustment is not appropriate.

Sound BD and speaker are malfunctioning. Adjust sound volume. (see Section 7).

Perform sound test to find and replace defective parts.(Refer to Section 7).

Page 34
  • CONTROL PANEL/BAT MECHA

@ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an

WARNING! electric shock or short circuit accident.

12 - 1 CONTROL PANEL

FFA PE PLAYER 1

  • \ WP 2Peey BBUTTON _/ e 7” START OOH apuTTONFFH<- ANALOG BAT MECHA PLAYER 1 FFH

EXPLANATION OF CONTROLS:

ANALOG STICK: Move cursor (for throwing, batting); Specify base (for defense, base running) SW1: Throw (for defense); Steal base (for batting); Advance to next base (for base running) Enter command (within acceptable time). SW2: Check runner (for throwing); Move between bases (for defense); Return to base (for running) Enter command within acceptable time). BAT MECHA: Throw, Swing. START: Start game; Time out (for throwing, batting)

The analog input on the I/O board uses the following channels: CHO: 1P ANALOG STICK VOLUME VERTICAL —UP(FFH) | DOWN(00H) CH1: IP ANALOG STICK VOLUME HORIZONTAL = LEFT(FFH) RIGHT(00H) CH2: 1P BAT MECHA VOLUME = STANDARD POS.(00H) MAX(FFH) CH3: (RESERVE) CH4: 2P ANALOG STICK VOLUME VERTICAL ~UP(FFH) |» DOWN(00H) CHS: 2P ANALOG STICK VOLUME HORIZONTAL LEFT(FFH) RIGHT(00H) CH6: 2P BAT MECHA VOLUME = STANDARD POS.(00H) +MAX(FFH) CH7: (RESERVE)

Page 35

IREMOVING AND ATTACHING THE BAT MECHA

If you need to remove the BAT MECHA as in the case of a failure, open control panel base and remove the BAT MECHA through the following procedure. To reinstall the BAT MECHA, reverse the removing procedure, being certain that the BAT MECHA is faced in the correct direction.

To prevent electrical shock, be sure to turn off power to the cabinet when removing or attaching the BAT MECHA

CAUTION!

1.) Remove the wiring connector (AMP 3P, white) located near the volume.

2.) Remove the tamperproof screw clamping the bat center axis on the front side of the control panel.

3.) Remove the four flange nuts clamping the BAT MECHA body on the back side of control panel.

PART NO.: 610-0408 PART NAME: ASSY BAT MECHA

Page 36
  • GAME BOARD

@ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an

WARNING! electric shock or short circuit accident.

Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at the

CAUTION! time of shipment.

13-1 REMOVING THE GAME BOARD

To replace the IC Board or to change dip switch settings, take out the IC board using the following procedure;

Turn main switch off.

Unlock Cabi Drawer, pull outward, exposing all game components. Disconnect all connectors connected to the Shield Case. Take off the 4 screws to remove the Shield Case. The game board Disconnect & _all the Connectors ©E8O0 is inside the shield case.

SCRERS (2) SHIELD CASE, MAX8.w/flat & SHTELD CASE LID spring washers

WING BOLT(2) M4X30, flat washer used

Page 37

13-2. COMPOSITION OF GAME BOARD

Ensure that the DIP SW setting is performed as designated. Failure to observe this may cause functioning not suitable for the operation of product, or malfunctioning.

IMPORTANT!

ASSY CASE NAO USA (840-0003D-01) : WORLD SERIES ‘99

SCREW_(4) M3 X55, flat & spring washers used

ROM_BD SCRER_(3) M3X16, flat & spring washers used SCREW (2) W3X35, flat &

I spring washers used

MAIN RD NAOMI COM USA_840-0003D-01 SPACER_BD_NAOMI 105-5357

Page 38
  • DESIGN RELATED PARTS

MARQUEE PLEX ‘999-0820

CABI SIDE Re999-0814 Le999-0815

IN: 0 999-0816

999-0817

999-0818

CABI FRONT RIGHT 999-0819

Page 39
  • PARTS LIST TOP ASSYMLB
Page 40

TOP ASSY MLB_WS99

ITEM NO. PART NO.

1 NOT AVAILABLE* 2 HODI1-1570 3 SEE DESCRIPTION* 4 SEE DESCRIPTION* 5 SEE DESCRIPTION* DESCRIPTION

ASSY BILLBOARD MLB_WS99 ASSY MONITOR 29TYPE 31K ASSY CONTROL PANEL MLB_WS99 ASSY COIN TOWER ASSY SUB-CABINET MLB_WS99.

  • THESE ITEMS ARE NOT SOLD AS COMLETE UNITS, PLEASE SEE INDIVIDUAL ASSEMBLIES FOR PART

NUMBERS OF ALL ITEMS CONTAINED ON THEM.

Page 41

ASSY SUB CABI MLB_WS99

Page 42

ASSY SUB CABI MLB_WS99

ITEM NO. PART NO.

NOT AVAILABLE HOD-1530 HODS5-4500 DRT1-0400 92-1003-05 BOX-CASH 601-5699X, 601-9377 999-0781 HODS5-3500 999-0782 AIN-1033 COP-1510 ARC-1006 SCR-1008 HOD-1502 HOD-1505 253-5460-01 DP-1148X DP-1167 117-0062 117-5098 DESCRIPTION

ASSY CABINET FAN UNIT ASSY ELEC BASE ASSY AC UNIT ASSY C.C. 2 DOOR CASH BOX LEG ADJUSTER BOLT M16X75 CASTER FAI=75 MONITOR GLASS 29" MLB_WS99 ASSY BILLBOARD MONITOR BEZEL 29" MLB_WS99 GLASS HOLDER UPPER GLASS HOLDER LOWER LEG BRACKET NUT PLATE FOR CASTER FRONT DOOR L FRONT DOOR R AIR VENT BLACK LKG TNG TNG LKG PLATE LOCK RETAINER TNG RETAINER PLATE

Page 43

ASSY BILLBOARD

ITEM NO.

ARwYNe PART NO.

HOD1-3501 JPT-3502 999-0820 HOD-3504 HOD-3505

LOCAL PURCHASE

000-FOO408-0B 000-TOO408-0B 000-P00430-W 000-T00412-0B 068-441616-0B DESCRIPTION

BILLBOARD CASE REFLECTOR MARQUEE PLEX LAMP COVER B BILLBOARD UPPER SASH

ASSY FL20W SD W/CONN HIGH L

M SCR FH BLK M4X8 M SCR TH BLK M4X8 M SCR PH W/FS M3X30 M SCR TH BLK M4X12 FLT WSHR BLK 4.4-16X1.6

Page 44

ASSY CONTROL PANEL

ITEM NO. PART NO. DESCRIPTION

1 999-0824 CONTROL PANEL PLATE MLB_WS99 NAO

2509-5560-YPB SW WIL6V ILY

3 610-6723-4C01 ASSY ANALOG JOY 4C GREEN

4509-5561-GPB SW W/L6V 5LG
5610-0409ASSY BAT MECHA
Page 45

ASSY COIN TOWER

SEE B

ITEM NO.

wre & PART NO.

SPG1-0350 DP-1167 BOX-CASH 105-5202 92-1003-05* 220-5412 220-5574 220-5575 0 || @e

ES

DESCRIPTION

SW UNIT TNG LKG CASH BOX HOLE COVER ASSY C.C. 2DR MAG CNTR W/CONN CAM LOCK W/KEYS CAM LOCK MASTER W/O KEY

*This is a COIN CONTROLS PART No. and can be ordered through them, please view insert in the COIN DOOR,

Chapter of this manual for more information.

Page 46

ASSY SW UNIT (SPG5-0350)

ITEM NO. PART NO.

SPG5-0351 509-5028 220-5179 601-0042 220-5412 509-5453-91-V-B SOUND VOLUME

DESCRIPTION

SWITCH BRKT SW PB 1M VOL CONT B-5K OHM KNOB 22MM MAG CNTR W/CONN ROCKER SWJ8 V-B

Page 47

ASSY AC UNIT (DRT1-0400)

ITEM NO. PART NO.

SPG1-0401 600-5843-25 280-5134-6N34 LOCAL PURCHASE 509-5453-91-V-B DESCRIPTION

AC BRKT CA & PLUG ASSY 15A W/F-L=2.5M BUSHING STRAIN RELIEF 6N34. FUSE 5A SW ROCKER J8 V-B

Page 48

ASSY MONITOR 29TYPE 31K (HOD1-1570)

[7 ri

SECTION A-A

ITEM NO. PART NO. DESCRIPTION

1AIN-1026MONITOR BRKTA
2AIN-1027MONITOR BRKT B
3280-5112BUSH FOR TV
4280-5113COLLAR FOR TV
5280-5114SPACER 6.4-25X2

101 200-5787 ASSY CLR DSPL 29TYPE 31K 100V.

201 000-P00512-W M SCR PH W/FS M5X12

202050-F00600FLG NUT M6
Page 49

ASSY PWR SUPPLY U/R (MLB-4500)

2-920

oooo0 ooo

C4 ry Bs | ° CJ 2)

  • (203) we

ITEM NO. PART NO. DESCRIPTION

1 NOT AVAILABLE WOODEN BASE ELEC

2838-11650-29EQ PWR AMP JPT C
4839-0979LAMP COVER B
201011-P00325TAP SCR PH 3X25
Page 50

ASSY MAIN BD U/R (MLB-4600)

a

a ooc™ 00 a al]

le 1)

lo )

ITEM NO. PART NO. DESCRIPTION

1105-5345ASSY SHIELD CASE NAOMI

2 NOT AVAILABLE WOODEN BASE MAIN BD U/R

3837-135511/0 CONTROL BD FOR JVS
101400-5330-03SW REGU FOR MODEL3
203000-P00416-WM SCR PH W/FS M4X16

204 011-P00325 TAP SCR PH 3825

Page 51

Come see SEGA ENTERPRISES’ Service Department Homepage

Netscape: SEU SERVICE HOMEPAGE

ivr? @M@emadcec &

  • Go To: & http://www .seuservice.com/SEGASERYICE /mainpage.html

WHAT'S NEW

MANUALS

BULLETINS

PART NUMBERS

GAME MONITORS

BOARD SYSTEMS

MAILING LIST

SEGA DISTRIBUTORS

SERVICE STAFF

DARL'S OFFICE

HOME

[¥2K COMPLIANCE]

Sega Enterprises Inc.,USA Service Department Phone (650)-632-7580 Fax (650)-632-7594

Best Viewed with AI what’s Related [what's new] [Manuals] [Bulletins] [Part Numbers] [Game Monitors] [Board Systems] [Mailing List][SEGA Distributors] [Service Staff) [Darl's Office][Samples)

Coin-Op Links:

Star Tech Journal

Amusement industry Mega Site

if you have any questions about this Home Page please E-Mail to:

dari.davidson@seu.sega.com OR fan.rockhili@seu.sega.com

A total of BRR WIE My people have accessed this page.

Page 52

SEGA

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax

Page 53

ASSY SHIELD CASE NAO MLB (840-0012D)

ITEM NO. PART NO. DESCRIPTION

1 840-0001A-01 GAME BD MLB_WS 99 USA 2 840-0012C ROM CASE