CATHODE RAY TOMES

Top Landing

Top Landing (World) (Taito Corporation Japan, 1988) · Manual · 27 pages · 13 sections · original scan

Page 1

TAITO

SERVICE INSTRUCTIONS

AND PARTS CATALOGUE

TAITO CORPORATION G25 00482A

Page 2

TOP LANDING

Specifications:

  • Power Supply 100 VAG (50/60 Hz)
  • Power Consumption 125 W
  • Play Pricing 1 Play - 1 Coin (Adjusutable)
  • TV Monitor ‘ 20-inch Color
  • Dimensions Width : 600 om Depth : 975 om Height: 1760 om
  • Weight Approximately 100 Kg

x The specifications and appearance may be changed for improvement.

Table of Contents:

  • Overview Description .............. ner eeneneee enane 1 oheae ie seceeeee lt
  • Installation ........... eee eeeeeers cae ceeeerensenasseereeseseene 2

FQ. Handling Care ...ceeeveceeveecveeeeeerere eee eee ene eee neces 3

  • Safety Measures .......eeeeeeeeee dee ee cae eenaee vee ewes is veceee
  • Central Control ...cesvesevevseeereverererereceners sees 4

§. Headphone Control .........-.-008. see eeeee Seen esenenteee weed A

T. Switching Regulator .....ccccceeeseeeeeeeeeneee ese e en neeeennees 5

  • Adjustments of Color Video Monitor .......eseeeeserere eee ree 6 Fog. Play Instructions .......ceeeeeeeseeee veces sae eeeees seceeaee 9
  • Test Wode .....eeeeeeee eens eee corre eens antes e weed
  • Adjustments of Main PC Board .......... bed e cece neces eseeneees oS
  • How to Remove Control Panel .........eeee dete nee enees te eeeenenes 16 = Parts Catalog ......... tenegee tee e cece eeeeen sees Peewee ae sau ee 17 Cable Block Diagram
Page 3
  • Installation

¢ Avoid rough handling in transportation; the picture tube is fragile.

e This machine is designed for “indoor” use. So install the machine indoors only.

e Install the machine on flat-surfaced floor (made of concrete, etc.) and provide suitable space around it. Do not install the machine in locations with vibrations.

° Do not install the machine in locations exposed to sunlight or excessive heat to avoid the environmental temperature rise. Also, do not install the machine at places where it is humid and/or dusty.

e Do not install the machine in dangerous places in view of disaster prevention, five alarm equipment, etc.

e Never fail to connect the "ground terminal” of the machine and the "ground line” of the porer supply cord.

¢ Before turning on the power switch! The screws for fastening the parts may be loosened by vibrations, etc. in transpotation. Make certain that the PC board is correctly attached and the connectors are perfectly plugged.

e Plug the power cord plug into the outlet and turn on the power switch. Before this, make sure the power supply and the current capacity.

e In case that any malfunction occures after turning on the power: First, turn off the power switch, and check the power supply and each output by referring the handling care. This machine does not work normally unless the proper power supply voltage is supplied.

Page 4

Handling Care

e This game uses microprocessors and other ICs for long stable performance life, however, as with sophisticated electronic equipment, certain precaution must be observed to avoid damage.

+ Do not attempt to service with ordinaly testing equipment, since the internal voltage of testing equipment may cause damage to

the circuitry.

+ Never connect or disconnect any of connectors of the PCB set when

the power is on.

eAs higher voltages exist in the video monitor, extra care must be taken when inspecting and adjusting the video monitor.

¢Do not use fuses with other current capacity than specified. If the fuses with the specified current capacity are blown, check the power unit.

(Inside of Cabinet] (Outside of Cabinet]

Switching Regulator Connector Box Main Fuse 5A 3A SA

Maintenance

e Although this machine has been designed basing on the good safety standards, sowe trouble may occure in a long period. Therfore, it is necessary for the machine owner and operation manager to take daily checking to make sure that the safety condition of the machine is well kept.

Page 5
  • Central Control

wThe central control is located inside the rejector door.

e Sound. Volume Control Knob

Turning the knob clockwise increases the sound volume. Adjust it to suit the environment of

the location.

Service Switch By pressing this switch, the : : SOUND number of credits can be increased

without operating the coin counter.

Degaussing Switch Color aberration may occur depending on the setting condition of the machine. In that case, use the degaussing switch. Use this switch after an interval of 10 minutes when once used.

  • Headphone Control

w By using your headphone, you can enjoy playing the game with hearing

the powerful sounds.

° Phone The headphone with a 2.5-diameter terminal can be connected.

° Volume This is the sound volume control

for the headphone. Turning this "VOLUME" clockwise increases the

sound volume.

Page 6
  • Adjustments of Switching Regulator |

w If the line voltages are set at higher values than specified, the ICs may be broken. So use extreme care for this.

eWhen checking the output voltages, turn the potentimeter shown below slowly clockwise or counterclockwise by using a © small screw driver by referring to the table block diagram.

ZANWAUUNANTO Coon

aN

+ +50 VR

This is the potentiometer of adjusting the voltage of the +§ VDC line. By this potentiometer, the voltage can be changed + 10%. This voltage is preset at +5V.

Note: The voltages of +12 VDC and -5 VDC are fixed.
Page 7

[s. Adjustments of Color Video Monitor |

e The video monitor is properly adjusted before shipping, however, according to the condition of location, some adjustments may be required. In such case, refer to the following explanation.

=e

tr

@® R-BIAS© I.SIZE® WH. POSITION
@ G-BIAS© HW. HOLD® Screen-Size-Changig Chips
@ B-BIAS@ HW. PHASE@ Screen-Inversion Connector
@ R-GAIN@ V.SIZE@® Worizontal Frequency-Changing
® G-GAIN@ V.NOLD® FOCUSTaps
® B-GAIN@® V.POSITION@ SCREEN

@ BRIGHT @® V.LIN

*& Caution for Adjusting

+ Careless adjustments may result in malfunction such as synchronism, distortion of screen, and/or voltage-rising.

+ Never touch the adjustors with white-paint locking. Also, as higher voltages exist some parts of the monitor unit, extra

case must be taken when adjusting.

  • Depending on the setting condition of the machine on location, color aberration may occur. In such, use the degaussing switch or a

degaussing device. Be careful to avoid any magnet or the like nearing the screen, or color aberration will occur.

Page 8

e Explanation for Adjustors

R.G.B.-GAIN, BIAS

R.GAIN,BIAS +++ for changing the strength of red color G.GAIN,BIAS +++ for changing the strength of green color B.GAIN,BIAS «++ for changing the strength of blue color

BRIGHT (Brightness Control)

Use this control for adjusting the screen brightness. Adjust thise control depending on the condition of location.

H.SIZE (Horizontal Width Control)

Use this control for adjusting the horizontal Picture size.

When adjusting, use a core driver.

H.HOLD (Horizontal Hold Control)

Use this control when the picture rolls horizontally.

H.PHASE (Horizontal Phase Control)

Use this control for adjusting the horizontal timing.

V.SIZE (Vertical Picture-Size Control)

Ves this control for adjusting the vertical picture size.

V.HOLD (Vertical Height Control)

Ues this control when the picture rolls vertically.

V. POSITION (Vertical Centering Control)

Use this control to wove the picture vertically onto the desired position.

Page 9
  • Play Instructions
  • Description for Control Part

DESCENT INCREKEXT OF . LEFT RicuT (gl \ TURN i- TURN astent vee

Start Button Joystick Throttle Lever (Control)

+ Start Button ... Use this button to begin a game and to select airports.

+ Thottle Lever .. Use this lever to increase or decrease the power when increasing or decreasing the speed.

+ Joystick ....... Use this joystick for doing descent, ascent, left (Control) turn or right turn as well as for selecting airports.

Ascent : Turn downward. Descent: Turn upward. Ascent (Nose-up) a

\ Descent (Nose-down) Left Turn ; Turn right. Right Turn: Turn left. A.

Left Right Turn | Turn

Page 10
  • Description for Meters on Screen

WIND DIRECTION AND Im VELOCITY METER

METER TO CHECK NCE TO PLANE INCLINATION course ioicaron P'ST AIRE hip

ee LEFT OR RIGHT IN:

Peo CLINATION OF THE PLANE TO THE

PLANE BopY PLANE BODY ee AIRSTRIP,

Hionzon

+ Information Panel: displays the following notices.

"RIGHT TURN” baad Turn right ! "LEFT TURN” ~ Turn left !

"uP" iad Nose up !

“DOWN” =~ Nose down ! "POWER UP" ~ Increase the power ! (only in the taking-off scene)

  • Control Procedure

@® Insert coins. (Coins inserted for 10 or more credits are nullified.)

@ The words "POSITION JOYSTICK AND THROTTLE LEVER POSITIONS SHOWN IN

BLUE. COLOR” are displayed on the screen . When the joystick and the throttle lever are positioned into the positions shorn in blue color, the words of "PUSH START BUTTON”

are displayed on the lower part of the screen.

@® By pressing the start button, the game begins.

Page 11

( Take off Scene )

eA take off should be done according to the indications displayed on the screen.

esa = = ‘s = 7 7 @ TAKE OFF @ LEFT TURK @ STRAIGHT Goinc ® staat POSITION

®

MOVE THE LEVER TO THE LEFT | @ GRADUALLY.

PULL UP 1 The words of "INCREASE THE POWER SLIGHTLY”

are displayed. Increase the power slightly and move forward.

The words of "MOVE THE LEVER TO THE LEFT “GRADUALLY” are displayed. Turn the joystick left and move the plane to the center of the airstrip. When the plane is moved to the whith center line on the airstrip for going straight, the words "READY FOR TAKE-OFF {{" are

displayed.

When the speed reaches 200 kt, the words of "PULL UPI!” are displayed. Turn the joystick toward you to nose up.

Page 12

@® After taking-off, the words of "TAKE-OFF {” are displayed, and points TAKE OFF ! (meximam 100 points) are scored.

POINT 100

To follow are the failures of take off:

+ If the plane goes out from the airstrip before taking off. + If the plane was unable to take off. + If the plane did not take off within the given time.

( Selection of Airports )

eo After taking off, the screen changes to the landing-selection scene.

+ Airports can be selected according to their weather conditions.

+ By turning the joystick right or left to move the biue-blashing cursor onto a desired airport for landing, and select it by pressing the start button. (If no selection has been made within 10 seconds, an airport is selected automatically.)

( Name of Airports )

Tokyo , Fukuoka , Sydney , Rio de Janeiro , Osaka , Paris , San Francisco , and Washington D.C.

( Landing Scenes )

e The landing method of this game is the same way as that of the “Midnight Landing”.

@® By using the joystick and the throttle lever, nose down to go to the airstrip on which red calling-on lamps light, and lower the altitude of the plane by adjusting the power.

@® Just before landing, nose up slightly, and lower the power. (Approaching speed: 250 kt or less)

Page 13

@ When the plane lands safely on the airstrip, a reverse-jet is produced automatically to stop the plane. The word of "LANDING" is displayed on the screen.

« Score-decreasing items in landing: (The scoring system is a low-point method of scoring in which these score-decreasing item points are deducted from the basis of 100 points.)

+ If the plane goes up or down in a furry. + If the plane fishtails (or zigzags). + If the approaching speed is too fast. + If the plane does not move up when approaching into the airstrip. + If the plane lands on a place which is far away from the correct part of the airstrip.

( Game-over )

¢ Game ends when the plane failed in landing. The failures of landing are:

"COURS QUT” ...... When the plane is far away from the course. “CRASH” ... . When the plane comes to the ground. “OVER RUN" When the plane overruns the airstrip.

e After clearing all rounds, the ending mode is displayed, then the game ends.

Page 14
  • TEST MODE

e In the setting that the position 3 of the DIP switch located on the main PCB is turned ON, the test mode can be displayed by turning on the power switch.

® First, the words of “NOW SRAM CHECKING” are displayed, then crosshatching and color bars are displayed, which are to be used for adjusting the screen size and brightness.

@ Next, by pressing the start button, the screen changes to the test mode, on which the function test of the switches

as well as the confirmation of the DIP switch settings can be done.

TEST MODE COINA: OFF SERVICE: OF START: OFF A

Note 1: COUNTER 1 + Function Test for Throttle Lever ” 2 + Function Test for Joystick (Right and Left) " 3 + Function Test for. Joystick (Up and Down)
Note 2: SOUND CODE By turning the joystick right or left, select the sound code. Then, the sound output checking can be done by pressing the start button.

x The door switch is not used.

Page 15

io Adjustments of Main PC Board

  • Open the rejector door, and release the auto latch located on the upper part of the fronto door, and then open the front door. I LI

B ® ©) NOT USED SOUND VR

DIP-SW

Ho H{___}

+ Sound VR ... The sound volume can be increased by turning to the

direction as shown with the arrows. However, these volume controls are not used in a normal condition because the sound volume control is equipped within the rejector door as the central control.

Note: When changing the positions of the DIP switches never fail to turn off the power switch first.

( DIP-SW A) (*): FACTORY SETTINGS

SETTING POSITION

  • NORMAL GAME TEST MODE

PRODUCE NO PRODUCE 1 COIN 1 PLAY TEST MODE

ATTRACT SOUND

PLAY PRICING 2 COINS 1 PLAY (COIN A) 3 COINS 1 PLAY

4 COINS 1 PLAY

1 COIN 2 PLAYS 1 COIN 3 PLAYS

1 COIN 4 PLAYS 1 COIN | 6 PLAYS PLAY PRICING

(COIN B)

Page 16

(*) :FACTORY SETTINGS

F GAME DIFFICULTY EASY (A) DIFFICULT (D)

Note: The main PCboard used in this game is for exclusive use for the upright model, not for the mobile cabinet model.
  • How To Remove Control Panel |

@Release the Super Clamps (at 3 places; ® Remove right, left and upper ial places.) (2 pieces)

Open the door

+Procedure:

@® Open the door located below the control panel, and remove 2 pieces of thumb nuts (M4) on the front side of the panel.

@ The control panel can be removed after releasing 3 pieces of super clamps located on the both sides and the upper part of the panel and then by unplugging the N- and K-connectors.

Page 17

IT.

PARTS CATALOGUE

ug2

M07

MOS

Kg90

M90

M90

Mao

MgO

M03

MO1

MO1

MOL

M90 OO105A

001254

OO149A

Q1573A

Q1234A

O1512A

01033A

Q1S11A

15069A

000394

00089A

00088A

O1513A CABINET ASSY (MAIN) CABINET ASSY

REJECTOR & CASH BOX ASSY

CENTRAL CONTROL ASSY

FAN ASSY

FL ASSY

MAIN SWITCH BOX ASSY

SWITCH BOX ASSY

CONTROL PANEL ASSY

PUSH BUTTON ASSY

HANDLE CONTROL ASSY

ACCEL CONTROL ASSY

PC BOARD SHIELD ASSY

Page 18

ITEM

ere neone PARTS DESCRIPTION

CABINET ASSY (MAIN) (U92 00105A) £50 E30 E30 E30 G95 £30 £50 £30 £50 H30 D20 H1O G15 H1O G1 G15 G15 G15 G15 £30 £30 G15 G95 001534 000G6A 000084 OS999A 003694 059984 60028A Q5994A 000934 000414 OO6G3A 04062a 00222a 00074A 002234 Q0224A 00225A 00226A 002374 O5996A Q5997A 00058A OO371A SERVICE LOCK NO.8800 SINGLE LOCK GUARD B LOCK PLATE LONG SIZE TITLE BRACKET B TITLE PANEL TITLE BRACKET A SUPER CRAMP C-137 STOP BRACKET AUTO LATCH MASK FRONT BOARD FLENEL LENS (320x390) F900, T=2.0 LNO8&S FRONT PANEL SHEET FRONT GLASS SIDE STICKER A-L SIDE STICKER A-R SIDE STICKER B-L SIDE STICKER B-R MARK STICKER 200 EDGE COVER F EDGE COVER S HIGH VOLTAGE CAUTION STICKER DISPLAY BOARD [SPARE PARTS]

CABINET ASSY (M07 00125A) D30 £30 E50 E30 E30 001628 027254 GO01LA 06002A O6001A

REJECTOR &

MOS E50 E50 E30 E30 £30 C17

Lg90 Lao QO137A QOL13A 001024 034974 O5599B 056008 O0035A

013838 OL704A CABINET ROPE HANGER CASTER 420SR-N D=75 CASTER BRACKET SUPPORT BRACKET

CASH BOX ASSY (M05 001494) DOOR & CASH BOX (NO.29311) LOCK & KEY LY-0069 DOM LOCK LOCK PLATE CASH BOX CASE CASH BOX COUNTER GX-O6F DCSV

E HARNESS C HARNESS

Page 19

@FL & CENTRAL CONTROL ASSY

Page 20

ITEM

ae one

V7 PARTS NO.

FL ASSY (M90 01512A) CLS 00004A

COS 50303

C10 00304A

C14 OO101A

COS 503524

190 O1669A DESCRIPTION

FL LAMP 15W

FL SOCKET 1A 250V

CHOKE TRANSFORMER 15H

GLOW LAMP FG-1P

GLOW SOCKET 1A 250V

FL HARNESS

CENTRAL CONTROL ASSY (M90 01573A) E30 050558

C02 00033A

CO2 OO164A

E90 OO416A

G10 001864

G10 10010A

G10 O0219A

L90 O1365A

FAN ASSY (H90 012344) E30 O1004A

C12 O0058A SWITCH BRACKET

PUSH BUTTON SWITCH VAQ-4R ROTARY SWITCH 1505-134

KNOB

SERVICE SWITCH STICKER

DEGAUSSING SWITCH STICKER

SOUND VOLUME STICKER

D HARNESS

PUNCHING PLATE B FAN WEJ-S5B4 -

CABINET ASSY (MAIN) (U92 001054) AGO 00102A

£30 01336A

p20 00046A MOB 00094A SPEAKER 8 OHM 15W 12CH

PUNCHING METAL

SPEAKER BOARD

VIDEO ASSY 20" HS8-20NT

Page 21

@ CABINET ASSY

Page 22

ITEM

ewan eon

MW

ie)

V7 PARTS NO. DESCRIPTION

CABINET ASSY (MAIN) (US2 00105A) CO7 00208A AC CORD 3¢

F90 00048A CORD STOP

C18 O0008A NOISE FILTER 2NB2206-02

F90 O0636A MAIN SWITCH COVER

G10 00304A.ON-OFF STICKER
M41 000238.SWITCHING REGULATOR

M41 00027A CONNECTOR BOX ASSY

G10 00002A.SERVICE OUT STICKER

F90 00909A SWITCH COVER

C10 00358A TRANSFORMER

COG 00330A D-TYPE TERMINAL 6P ML-2015C

G15 OO193A VOLTAGE STICKER

L90 O1713A S HARNESS

L90 O1714A 7 HARNESS

L10 001604 MAIN HARNESS

MAIN SWITCH BOX ASSY (M90 010334) E30 O1861A MAIN SWITCH BOX

CO2 00020A TOGGLE SWITCH ET125A-12

SWITCH BOX ASSY (M90 O1511A) E30 05056A FUSE BRACKET

COG 01002A EARTH TERMINAL 1-375 BK

COS 50144A FUSE HOLDER S-N 2056

C16 000374 FUSE 5A

G10 OO1L9A CONNECTOR STICKER E

G10 000934 FUSE STICKER SA

Page 23

@ CONTROL PANEL ASSY

Page 24

@ HANDLE CONTROL ASSY

Page 25

@ACCEL CONTROL ASSY

Page 26

@PC BOARD SHIELD ASSY

ITEM

PARTS NO. DESCRIPTION

PC BOARD SHIELD ASSY (M90 01513A) H90 002324 SHIELD CASE M43 OOLI4A or MAIN PC BOARD ASSY

M43 OOLISA

E30 O5995A EARTH JOINT £30 O6000A SHIELD DOOR

Page 27

Colt METER (A) Tio] ie

COIN LOCKOU

“o

& COIN Sw (A) x2 —a4po-——_| SPEAKER VR SW

Cc C

(x2 ce

Cc

T ee E ft im

UST ITS TPO Neti ie

(MAIN P.C.BOARD ASSY ) CPU P.C.BOARD ASSY I bdo VIDEO ASSY 20 te

POSITION SW: THROTTLE DOWN

'UP-DOWN PULSE I~: THROTTLE UP POSITION SW-] LEFT POSITION SW~| RIGHT Pos!tION Swiss DOWN POSITION SW-{[S UP POSITION SW:

o SOUND SW a

SOUND SW 2-1

SOUND SW 3+] > PILOT LAMP] T eee START Sw RIGHT - LEFT

i

ae i

TIGZLEEEM

VIDEO P.C.BOAD ASSY : i +

TeIsioh wal T STS tha N mictine

MAIN SW. 00.0.

AC S00¥

SWITCHING REGULATOR ASSY

CONNECTOR BOX ASST

via

he all ery WIRI. [Bonen |W 1000 15 2 TAITO CORPORATION

GRA oe —— —