CATHODE RAY TOMES

Crystal Castles TM-241 1st Printing

Crystal Castles (version 4) (Atari, 1983) · Technical Manual · 72 pages · 62 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts and Service

Atari, Inc. California Customer Service Office 1105 .N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) POF From California, Alaska, or Hawaii (408) 745-2900 zs Service from anywhere in the area shown in white toll-free (800) 538-1611

EAST U.S.A. Service only

Atari, Inc. New Jersey Customer Service Office 12A World’s Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey s (201) 469-5993

From anywhere else in this area & toll-free (800) 526-3849

EUROPE Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28-165 TIPPERARY TOWN. (Monday-Friday, 9:00-6:00 pm GMT) IRELAND

BS 06252155

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

Crystal Castles

© 1983 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 7™

Page 5

Crystal Castles

Notice Regarding Non-ATARI Parts

Use of non-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game.

  • Modify or alter any circuits in the game by using kits or parts mot supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in acommercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:

  • All green ground wires in the game are properly connected as shown in the game wiring diagram. « The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit boards (PCB)are properly installed within the Electromagnetic Interference (EMI) cage.
  • The EMI Shield PCB is properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.
Page 6

Crystal Castles

Table of Contents

Set-Up How to Use This Manual . . Game Overview Installation Specifications . Inspecting the Game . Voltage-Plug Selection and Fuses . Switch Locations .............44 Selecting the Coin, Credit, and Game Options Game Play... 6... Power-Up Self-Test Mode. . . . Attract Mode . : Ready-to-Play Mode Play Mode......

Self-Test Entering SelfTest........... SelfTest Main Menu ... .

Troubleshooting Troubleshooting Aids .. . Troubleshooting Techniques . .

Maintenance Cleaning Requirements ....-.........-.- saele ee ney Opening the Control Panel... 0.02.02. eee Pushbutton Leaf Switches .......... Lighted Midi Trak-Ball Assembly . Video Display Shield... ..... Speaker Grille Assembly . . : . : bees sae Removing the ATARI CRT Assembly Sages se weg a ee eve ery eee yaene

Illustrated Parts Lists For complete list of all illustrations, see following page

Glossary of Terms Glossary of Terms begins on page GL-1

Page 7

List of Illustrations

Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5

Figure 5-1A Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9 Figure 5-10 Figure 5-11 Figure 5-12 Figure 5-13

Table 1-1 Table 2-1 Game Overview «20.0.6 eee ees 1-2 Voltage-Selection Plug and Fuse Locations 1-4 Switch Locations ...... 15 Opponents of Castle 3, Level 7. . 1-8

Test Passes Video Display 2-2 EEROM Failure Video Display . . 2-2 ROM Failure Video Display 2-2 Self-Test Main Menu Video Display 23 Grid Video Display 23 Accounting Video Display 23 Clear Accounting Video Display . . 2-4 Game Options Video Display .. . . 2-4 EEROM Test OK Video Display 2-5 Switch Test Video Display ..... 2.6.0.0. 0-002 c eee eee 2-5

Midi Trak-Ball™ Assembly and Lubrication 43, Excessive Shaft Wear .. . 44 Speaker Grille Removal . 45 Speaker Removal . 45 CRT Removal ... . 4.6

Illustrated Parts Lists

Cabinet-Mounted Assemblies, US-Built Cabinet Control Panel Assembly . Lighted Midi Trak-Ball™ Assembly .. Fluorescent Tube and Attraction Panel Assembly Speaker Assembly . Utility Panel ‘Assembly Vertically Mounted Coin Door . American-Made Coin-Door Assembly . EMI Cage Assemblies and PCB Mounting Hardware . EMI Shield PCB Assembly ..... Crystal Castles™ PCB Assembly . . Regulator/Audio II PCB Assembly . Power Supply Assembly .........0. 0... 00s cscs esses weg aee

List of Tables

Installation Requirements... 2.2.2... eee 13 RAM Failure Tone Sequence... 2... 6... ee 22 Crystai Castles

Page 8

Crystal Castles

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

& WARNINGS A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire oudet. If you have only a2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game's power supply. Disconnect Power Duriag Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To mainuain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts Or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do Not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.

Page 9

Set-Up

How to Use This Manual

This manual, written for game operators and service technicians, describes your new ATARI game. Chapter i contains a game overview, game specifications, inspection procedures, voltage plug and fuse information, switch locations, and option information. Chapter 2 contains self-test procedures, Chapter 3 contains troubleshooting procedures. Chapter 4 contains maintenance and repair procedures. Chapter 5 contains illustrated parts lists. Notes in this chapter refer you to other places in the manual for more detailed information. Schematic diagrams of the game circuitry are included as a supplement to this manual.

WARNING Shock Hazard To avoid electrical shock, do not plug in the game until it has been inspected and properly set up for the line voltage in your area. Do not touch internal parts of the display with your hands or metal objects!

Chapter 1

Page 10

serup Crystal Castles

Fluorescent Tube & Attraction Panel See Figure 5-4 Game ienitieation

EM! Cage Not Used in Ireland See Figure 5-9 Game PCB & Insided EM! Gage See Figure 5-11

Video Display * See Figure 5-1

Deflection PCB x : EMI Shieid PCB Used with Atari Display. . Not Used in Ireland See Figure 5-1 4 i 5 control Panel ig mA i , See Figure 5-10 See Figure 5.2 & r

See Figure 5-12

Lighted Midi Trak-Ball See Figure 5-3

See Figures 57 01 5-8 Q

ity Panel See Figure 5-6 Do not plug inthe game until it has been inspected. This game should only be connected toa grounded 3wire outlet. if you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shockif this game is not properly grounded! Item with a serial number label

Figure 1-1 Game Overview

1-2

Page 11

Crystal Castles

Game Overview

Crystal Castles is a merry chase into a mythical land of incredible creatures that thrill at every turn of game play. Its hero, Bentley Bear, collects gemstones as he moves around 16 different playfields, including a castle, fortress, palace, and even a dungeon. Scary creatutes, such as nasty trees, gem eaters, a swarm of bees, and Berthilda the witch, chase Bentley Bear as he explores tunnels, elevators that take him from One plateau to another, and sometimes a secret ramp. Crystal Castles has three new features. Even if you are familiar with Atari games, you should note these important differences:

Lighted Midi Trak-Bal!™. The Midi Trak-Ball on the control panel of this game is translucent. A small lamp contolled by the game PCB shines through the ball. The result is a glowing Trak-Ball. During game play, the lamp flashes on and off creating a spectacular effect. Game Playfield Color Changes. You may notice that the castles and gems occasionally change colors. This isa feature, not problems with the color display. After each one hundred paid games, the color schemes of the castles change colors. All major parts of the cabinet are illustrated in Figure 1-1.

Installation Specifications

Table 1-1 describes the physical, electrical, and environmental specifications of the game.

Table 1-1 Installation Requirements

Characteristic Requirement

Power Consumption 120 W Temperature 0° to +32°C(+32° to +100°F) Humidity Not to exceed 95% relative Line Voltage 100 to 240 VAC Width 65.4.cm (25.75 in.) Depth 78.7 cm (31 in.) Height 182.9 cm (72 in.) Set-up

Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition. 1, Examine the exterior of the game cabinet for dents, chips, or broken parts.

  • Remove the screws from the rear access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harnesses) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets, ¢ Unhook the power cord from the top of the game cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. d. Inspect the power supply. Make sure the fuse block is mounted in place. Check that the green ground wires are connected. e. Inspect other major subassemblies, such as the control panel, video display, EMI cage, and each PCB. Make sure they are mounted securely and that the green ground wires are connected.
Page 12

setup

Voltage-Plug Selection

and Fuses

The power supply in your game contains six fuses. When you replace a fuse, use the identical type fuse with the same electrical rating (see Figure 1-2). This power supply operates on the line voltage of many countries. The power supply comes with either one, two, or three voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire Color), 220 VAC (blue wire color), and 240 VAC (brown wire color).

Fuse F2 4A, 250V

Fuse F3 20A,32V

Fuses F4-F6

4A, 250V Crystal Castles

See Figure 1-2 for placement of the voltage-selection plug. Before plugging in your game, check your line voltage. Next, check the wire color on the voltage-selection plug. Make sure the voltage-selection plug is correct for the line voltage of your location. Now plug the game into a grounded 3-wire outlet.

7 A, 250 V for US-Built Games 4A, 250 for \reland-Built Ganes

J3

Fuse cover is shown in Figure 5-13.

Figure 1-2 Voltage-Selection Plug and Fuse Locations

1-4

Page 13

Crystal Castles

Switch Locations

Power On/Off Switch

The power onioff switch is located on the back of the cabinet on the lower left side (see Figure 1-1).

Utility Panel Switches The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-2). The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the self-test mode. The auxiliary coin switch credits the game without activating a coin counter. See Figures 1-3 and 5-6 for details of these switches.

Option Switch Figure 1-3 shows the location of the dual-inline-package (DIP) switch at R8 on the game printed-circuit board (PCB). This option switch controls whether coins are counted on 1 or 2 coin counters.

Setting the Coin Counter Switch ‘Toggle i of this option switch is the only switch that is used. When setto the ON position, the left and right coin counter outputs of the game PCB are paralleled together. Sevtip

Therefore, any coin received from the right or left coin inputs will be counted on one counter connected to either the left or tight coin-counter output. The US-built garnes have one coin counter. Therefore, on US-built games, toggle 1 of the switch should be set to ON. When toggle 1 is set to OFF, a second coin counter must be connected to the unconnected coin counter output For [reland-built games, the second coin counter is standard. Therefore, on Ireland-built games, toggle 1 of the switch should be set to OFF.

Selecting the Coin, Credit, and Game Options

Setting the coin, credit, and game options is done with the player controls during the SeifTest mode of operation Therefore, you should never need to remove the game PCB from the electromagnetic interference (EMI) cage unless the PCB is in need of repair. Ali selected options are retained in a special integrated circuit (IC) on the PCB. Even when the power is turned off, the selected options are saved in this IC. To select the coin, credit, and game options, see Chapter 2, Self-Test Procedures.

Coin Counter:

Self-Test Switch

Volume Control To mcrease. turn clockwise Auxiliary Coin Switch Game PCB

RS OFF af “a on

Figure 1-3 Switch Locations

Page 14

set-lip

Game Play

Crystal Castles is a fastaction, 1- or 2-player, third-person adventure game. By using the Lighted Midi Trak-Ball, the player moves Bentley Bear about the castle walkways and walls to collect gems. To avoid being overpowered by gem eaters, nasty trees, or bee swarms, use the left- or right hand jump buttons. Crystal Castles has 6 modes of operation; the power-up self-test mode, the attract mode, the ready-to-play mode, the play mode, the hall-of-fame entry mode, and the self test mode.

Power-Up Self-Test Mode The power-up self-test mode begins when power is applied to the game. The power-up self-test checks the random-access memory (RAM), the electrically erasable read-only memory (EEROM), and the read-oniy memory (ROM) of the game PCB. If any of these tests fail, a message on the display or tones from the game speakers identify the failing component(s). If the tests pass, the game program advances to the attract mode. Refer to Chapter 2 for a description of the menu-driven self-test mode selected by the self-test switch located on the utility panel. Attract Mode ‘The attract mode consists of 4 displays: the coin message display, the game demonstration display, the hall-of-fame display, and the hints display. The coin message display begins after the power-up self-test, after the play mode, or after the hall-of-fame entry mode. This display lasts for about 10 seconds and is oniy interrupted by depositing a coin or by entering the selftest mode. The coin message display starts with a threedimensional painting of the game playfield and the firstlevel, first-wave castle. At the top left of the display is a box that, during game play, contains the player(s)score(s). During the attract mode, the score(s) are displayed only if the Player(s) of the previous game didn’t get a high enough score to enter their initials into the hall-of-fame table. At the top right of the display, the coin message appears in a large box. [n this box, the message INSERT COINS appears and disappears. Immediately below the insert coins message is the message 0 CREDITS. If the previous piayer reached castle 2 of level 2 (or beyond), the highest score of the hall-of-fame table appears immediately above the insert coins message. The initials entered for the highest score of the hall-of-fame table appear carved into the roof of the castle. Crystal Casties

The game demonstration display begins immediately after the coin message display. This display lasts about 10 seconds and is only interrupted by depositing a coin or by entering the self-test mode. The game demonstration display is similar to the coin message display except that Bentley Bear, three opponent crystai balls, and the gems are now displayed. The gems are on the walkways and walls of the castle. In the top right message box are the messages CRYSTAL CASTLES and COPYRIGHT ATARI 1983 ALL RIGHTS RESERVED. Soon after the beginning of this display, Bentley Bear moves about the castle walkway collecting gems. Point values appear in the top left box for each gem collected by Bentley Bear. Bentley Bear jumps a few times before coming in contact with one of the opponent balls. When Bentley Bear comes in contact with the ball, the cartoon caption 4!? comes from the mouth of Bentley Bear. Next, Bentley Bear “flies to heaven.”

The hall-of-fame display begins immediately after the game demonstration display. This display lasts about 10 seconds and is only interrupted by depositing a coin or by entering the self-test mode. At the top of the display is the message CRYSTAL CASTLES HALL OF FAME. Below this isa two-column listing of the 32 highest scores. If this list iscleared in the self-test mode, the scores range from alow of 27,000 to a high of 30,000 points.

The hints display begins immediately after the hali-offame display, or immediately following a game mode in which the player(s) did not reach ascore level sufficient for entering initials in the hall-of-fame entry mode. This display has the word HINTS across the top of the display, followed by four game hints. The first hint is about the magic hat that Bentley Bear can wear to make himself invincible. Both the hat and Bentley Bear are shown on the screen with the message MAGIC HAT MAKES YOU INVINCIBLE. WEAR IT AND YOU CAN KILL BERTHILDA. The second hint shows two gem eaters. One is eating gems and the other is shown moving from side to side. With these is the message CATCH GEM EATERS WHEN THEY ARE EATING. STAY AWAY WHEN THEY ARE MOVING FROM GEM TO GEM. The third hint shows the bee swarm with the message TAKE TOO MUCH TIME AND THE SWARM RETURNS. The fourth hint show the trees with the message JUMP OVER TREES TO STUN THEM.

eo 8&8 SF ®@B

1-6

Page 15

Crystal Castles

Ready-to-Play Mode ‘The ready-to-play mode begins when a coin is accepted by one of the two game coin mechanisms. This mode lasts until enough coins are received for a J- or 2-player game and the I-player or 2-player button is pressed. This mode is identical to the coin message display of the attract mode, except the coin message shows the number of credits, froma possible % credit toa maximum of 18 credits, resulting from coin{s) deposited into the game coin mechanism

Play Mode The play mode begins when enough coins have been

deposited in the game coin mechanism and the 1-player or

2-player start button is pressed. This mode ends after the last life has been lost during game play. The player’s objective is to collect all the gems from the castle walkways and walls by moving Bentley Bear about the castle with the Trak-Ball controller. Bentley Bear must collect ali the gems without being killed by any of the 8 possible computer-controlled opponents—crystal balls, trees, a swarm of bees, gem eaters, Berthilda the witch, a ghost, a skeleton, or a dust devel. In the lower levels of game play, this feat is easily learned by new players. In higher levels, experience, skill, and luck help the player to accomplish the objective. When game play begins, Bentley Bear is at the lower right corner of the castle walkway. Immediately after the player's control is enabled for moving Bentley Bear, the opponents are displayed about the castle walkways and wails. The player may move Bentley Bear either up or down the stairs or the elevators to get the gems. When Bentley Bear passes

over agem, the gem disappears. Points are scored for each

gem collected by Bentley Bear and shown in the score display area. If Bentley collects all the gems from the castle, the player receives bonus points. The initial bonus is 1,000 points for the first castle of the first level. The bonus is increased by 100 points for each subsequent castle (ie., the bonus for castle 2 of level 1 is 1,200 points; castle 1 of level 2 is 1,400 points; etc.). When astart button is pressed, the gems and Bentley Bear appear on the castle walkway and the game tune begins. Soon afterward, three crystal balls (the oniy opponents of this wave) drop from above and land at the far right corner of the castle walkway. These three balls begin a slow pursuit of Bentley Bear. As the Trak-Ball is rotated, Bentley Bear moves about the walkway. As he passes over a gem, the gem disappears and a score value is added to the score

inthe window at the top left of the display. If Bentley Bear

getsall the gems, the three balls rise outof sight above the castle. Then Bentley Bear also disappears. If Bentley Bear gets the last gem, the message YOU GOT THE LAST GEM. BONUS 1000 appears across the castle. If the opponents get the jast gem, the message THEY | GOT THE LAST GEM. NO BONUS appeats across the the castle. SevUp

Crystal Castles consists of 37 castle mazes that ate laid out with a walkway between each castle. The castles are arranged in ten levels with four castles on each level, except for level 10, which has only one castle. As Bentley Bear advances to the next castle on each level, the difficulty in col- Jecting all the gems increases. Each leveialso increases in complexity. The result is a nice variety of mazes, from the easy first castle of level 1 to the extremely difficult castles in the higher levels. At che beginning of play at each cas- Ue, a message appears in the window at the top right of the display. This message identifies the levei being played. Other messages, such as next bonus point level, also appear in this window. A message may appear in the message window to identify the activation of a warp. For example, if a player reaches castle 2 of level 2 (or beyond), a door appears in the first castle of level 1. If Bentley Bear enters into this door and the player presses the jump button, Bentley Bear will warp (advance) to the first castle of the third level. Some secret warps also exist. In this printing of the manual, we will tell you of two secret warps. One is located at the rear corner of the first castle of level 1. To use this warp, the player must move Bentley Bear to this spot and press the jump button. Bentley Bear will advance to the first castle of level 3. The second secret warp is in the rear corner of the hidden ramp of the first castle of level 3. However, Bentley Bear must be wearing the hat when he jumpsat this location. When this warp is used, Bentley Bear will advance to the first castle of level 5, Future printings of this manual will include other secret warps. Bentley Bear has eight opponents: crystal balls, trees, a swarm of bees, gem eaters, Berthilda the witch, a ghost, a skeleton, and a caldron. Figure 1-4 shows six of these opponents, which are encountered during game play. If Bentley Bear touches a gem.eater while it is in the process of eating a gem, the gem eater dies and 500 points are awarded the player. However, ifthe gem eater is not eating a gem when Bentley Bear touches it, Bentley Bear dies. When Bentley Bear is wearing his magic red hat, he is invincible. When he is wearing the hat he has the power to kill Berthilda the witch when he touches her. However, the magic of the hat only lasts about 5 seconds.

1-7

Page 16

Setup

Each of the opponents has its own characteristic. The swarm of bees appears near the honey approximately every five seconds. However if Bentley Bear takes the honey, he collects 1,000 points for the honey, and the bees will appear less frequently. The gem eaters are relatively stupid creatures. The only thing they are interested in is eating gems. However, ifgems are notin their area, the gem. eaters will rush around randomly looking for gems. The crystal balis and trees act much the same. They will go Crystal Castles

directly for Bentley Bear. However, if Bentley keeps obstacles between him and either of these opponents, he is relatively safe from attack. The skeleton and the ghost usually stay within their immediate areas, move about randomly, but not very fast. They guard their area well. Berthilda the witch flies around on her broom in one small area in the lower levels of game play. However, in the higher leveis she boldly flies about the castles.

HIDOEN SPLFAL

Figure 1-4 Opponents of Castle 3, Level 7

Page 17

Self-Test

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 18

Self-Test

Entering Self-Test

To enter the self-test mode, set the self-test switch on the utility panel to the ON (up) position (see Figure 1-3 for the location of this switch). The game tests the custom Input/Output (I/O) integrated circuits (ICs), the random-access memory (RAM), the bit-mode circuitry, the electronically erasable read-only memory (EEROM), and the readonly memory (ROM). Figure 2-1 shows the resulting video display if these tests pass. The custom I/O test is the only test not shown on the video display. If this test passes, you will hear sounds that range from alow frequency toa high frequency.

Figure 2-1 Test Passes Video Display

If the RAM fails, a sequence of seven “beep” sounds will be emitted from the game speakers, followed by a pause, then the sounds will be repeated. Table 2-1 identifies the failing RAM for the emitted sounds. In this table, the “High” indicates high tones from the game speaker and the “Low” indicates low tones. If the bit-mode circuitry fail will be emitted as follows: low.

If the EEROM fails, the video display will identify the failed IC as shown in Figure 2-2. The display will indicate a failed IC at either location 4A or 4B. a sequence of “beep” sounds igh, low, high, low, low, low, Crystal Castles

Ifa ROM fails, the video display will be as shown in Figure 2-3. In this figure, integrated circuit 1L has failed. The correct checksums are as follows: checksum 01 for 1K, 02 for 1L, 03 for 1N, 04 for 1H, and 05 for 1F. Checksums of any other value indicate a failure for that IC.

EEPOM FAILURE AT PC OYE

Figure 2-2 EEROM Failure Video Display

CHECKSUM FOR CHECKSUM FOR CHECKSUM FOR CxECKSUM FOR SHECKSUM FOR

Figure 2-3 ROM Failure Video Display

Table 2-1 RAM Failure Tone Sequence

Tone Sequence

1234567

PCB Location

HighLowLowlowlowlowLow
HighHighLowlowLowLowLow
HighHighHighiowlowLowlow
HighHighHighHighLowLowLow
HighHighHighHighHighLowLow

High High High High High High — Low

RAM at 4E. RAM at 4F RAM at 4H

RAM at 4J RAM at 6B RAM at 6D

2-2

Page 19

Crystal Castles

Self-Test Main Menu

Ifall initial self-tests pass, the main menu willbe dispiayed as shown in Figure 2-4. This menu allows you to select from seven different items. As indicated at the bottom of the display, set the self-test switch to off(down) to exit from self-test.

MOVANEE WITH LEFT SUTTON SELECT WITH @IGHT BUTTON

> sero

ACCOUNTING

ELERP RECOUNTING

BRME OPTIONS

TEST cEROM

SWITCH TEST

RESET HALL OF FAME

SWITCH SECF TEST SWITCH TO EXIT

Figure 2-4 Self-Test Main

Menu Video Display

Grid Display The grid display shown in Figure 2-5 is used for adjusting the video display. When properly adjusted, the grid should be white on a black background, The corners of the grid shouid just barely go off the corners of the display.

Figure 2-5 Grid Video Display Self-Test

Accounting Display The accounting display shown in Figure 2-6 is used for dis. playing historical information about the game. The photograph shown in Figure 2-6 was taken of an engineering prototype game. Therefore, in our example, no coins are shown for the left mechanism and only two coins for the right mechanism; but 46 coin credits are shown for the auxiliary coin switch. Ordinarily, the coin information is never cleared unless the EEROM are changed or damaged. Thus, this information may be compared with the information from the mechanical coin counter(s) for determining the accuracy of the mechanical coin counters. The most important information shown on the accounting display isthe average game time. This time should be between 2 and 3 minutes. The display in Figure 2-6 is a good example of optimum game time. A histogram of game time is shown at the bottom of the screen.

RECOUNTING

RuX COINS tery corns RIGHT COINS TOTRL RID COINS 1 PURVYER GAMES Z PLAVER GAMES TOTRL CREDITS PLAYEO AVERAGE GAME TIME MISTOGRRM

re NEENZENE eNdageecs wae

Page 20

Self-Test

Clear Accounting Display

The clear accounting video display is shown in Figure 2-7.

Note that the coin information is never cleared.

ACCOLNTING

fux corns Lerr corns FIGHT COINS TOTRL PRID COINS 2 PLAYER GAMES 2 PLAVER GAMES TOTAL CREDITS PLAYED AVERAGE GAME TIME HISTOGRAM NE BOGENNEE i]

a: 2: Zz: a: a se: s E: ONSEN

Figure 2-7 Clear Accounting

Video Display

Game Options Menu

The manufacturer’s recommended game options are shown in Figure 2-8. To move the arrow that points to each selectable option, press the left JUMP button. To change the option, press the right JUMP button. All available options are as follows:

COIN VALUE. The coin-value option determines the number of coins entering the left or right coin mechanisms, required to play one game. The values available are Ya, i, or 2, For game demonstrations, the FREE PLAY option is also available. LEFT MECH VALUE. The available left mechanism values are 1 or 2. The chosen value multiplies the coins received in this mechanism by that value. When set to 1, a coin dropped into the left coin mechanism of the coin door has the value of 1 coin. When set to 2, acoin dropped into this mechanism has the value of 2.

RIGHT MECH VALUE. The available right mechanism values are 1, 4, 5, or 6. The chosen value multiplies the coins received in this mechanism by that value. This option makes it possible to receive coins with a higher denomination than the left mechanism.

GAME DIFFICULTY. This option allows you to increase or decrease the difficulty of the game, thus increasing or decreasing the average game time. When used with the accounting display, you may tune the game for the optimum game time of 2 minutes and 30 seconds by setting this option to EASY, MEDIUM, HARD, or HARDEST. Crystal Casties

STARTING LIVES. This option allows you to increase the number Of lives per game from 3 to 5. The available options are 3, 4, and 5. Using this option along with the accounting display will allow you to tune the game for an optimum average game time of 2 minutes and 30 seconds. EXTRA LIVES, This option allows you to award bonus lives for every 70,000 points scored. The available options are YES and NO. Using this option along with the accounting display will allow you to tune the game for the optimum average game time of 2 minutes and 30 seconds. RESTORE FACTORY OPTIONS. This option allows you to restore the options to those retained in the game program memory. These factory-recommended options are shown in Figure 2-8. EXIT. This is not an option, but the way back to the main menu.

° GRME OF TIONS

GOINvrLue2 GREOrT
LEFTMECHvRLUE2
RIGHTMECHVALUE1

GAME DIFFICULTY MEDIUM

STARTING LIVES a

EXTRALIVESves

PESTORE FACTORY OPTIONS

exir

Figure 2-8 Game Options Video Display

Page 21

Crystal Castes

Test EEROM Display

If the EEROM test passes, the results of the test are shown in Figure 2-9. If either EEROM integrated circuit 4A or 4B fails, the failed IC will be displayed as shown in Figure 2-2. However, the message RAM OK will not be displayed.

Figure 2-9 EEROM Test OK

Video Display

Switch Test Display Inthe switch test, the left, right, and auxiliary coin switches; the left and right JUMP switches; and the Midi Trak-Ball are tested. When each switch is activated, the location of that switch appears on the display. In Figure 2-10 all switches are activated. When the left JUMP switch is pressed, the motion-object pictures change from one group to another. When the right JUMP switch is pressed, the motion-object pictures change within that group of pictures. The Midi Trak-Ball is tested by rotating the bali vertically and horizontally. The hexadecimal numbers by the words HOR and VERT increase from 00 through FF, or decrease from FF through 00, as the ball is rotated. Likewise, the numbers beside the words GREEN and BLUE increase from 0 to 7. The GREEN numbers increase or decrease with a horizontal motion of the Midi Trak-Ball. The BLUE numbers increase or decrease witha vertical movement of the contro}. Also, the colors of the color bar at the bottom of the display change shades of green when the ball is rotated horizontally and shades of blue when moved vertically, Self-Test

SWITCH TEST JUMP UTTON EQIN BUTTON cert RxGHT LEFT WIGHT AUX TRREKERLE TEST

Figure 2-10 Switch Test Video Display

Reset Hall-of-Fame When you select this from the main menu, the entire hallof-fame table is reset to initials and scores that are within the program memory. The scores in this table range from 27,000 to 30,000 points. We suggest you reset these after any changes are made to the options that may affect the average game time.

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

Troubleshooting

This chapter contains a discussion of troubleshooting aids and techniques to assist the service technician when a trouble is suspected in this game. Most troubles can be located quickly by following the information in this chapter. However, if problems persist, contact your nearest Atari Customer Service office listed on the inside front cover of this manual for assistance. A thorough knowledge of game operation is desirable for effective troubleshooting, In addition to the operation and service information in the Schematic Package Supplement included with this manual, refer to The Book, A Guide To Electronic Game Operation and Servicing, available from Atari, Inc., for more information on coin-operated electronic games.

NOTE We recommend that troubleshooting and repair procedures be performed by a qualified electronic technician.

Chapter 3

Page 24

Troubleshooting

Troubleshooting Aids

Troubleshooting aids are provided throughout this manual and the Schematic Package Supplement. The following information is intended to acquaint the service technician with the portions of these documents that contain useful troubleshooting and repair information.

Assembly and Component Locations The illustrated parts lists in Chapter 5 illustrate the locations of assemblies and components. Printed-circuit board (PCB) illustrations aid in rapidly locating components contained on the corresponding schematic diagram(s).

Schematic Diagrams

Complete schematic diagrams are provided in the Sche- Mmiatic Package Supplement. Component designations and their electrical values are included on the schematic diagrams. A memory map and a key to the schematic reference designators and symbols are also included in the Schematic Package Supplement.

Troubleshooting Procedures

This game will test itself and provide data to aid in localizing troubles to a major circuit. Self-test procedures are provided in Chapter 2. Refer to the following section on Troubleshooting Techniques for a suggested troubleshooting sequence that uses the self-test procedures. Detailed troubleshooting procedures for locating defective components are provided in the Schematic Package Supplement. These procedures use the ATARI CAT Box to troubleshoot the game PCB.

Troubleshooting Techniques

The following troubleshooting steps are arranged in asequence recommended for locating a defective component. The procedure begins with a check of the simple trouble possibilities and progresses to more extensive procedures for localizing the trouble to an assembly or major circuit, and then to a defective component.

Check Switch Settings

Incorrect switch settings can sometimes indicate a problem that does not exist. Refer to Chapter 1 Set-Up, to verify that the game has been installed properly and that the switches are set to their correct positions. Check for proper operation in all game-play modes.

Check Fuses Check for open fuses. Refer to the Power Supply Assembly Parts List in Chapter 5, Illustrated Parts Lists, and to the

3-2 Crystal Castles

Display Manual, for the location and rating of each fuse used in this game. Make sure that replacement fuses are the proper type and rating.

Check Power-Supply Voltages

Improper operation of all circuits usually indicates a power supply problem. Check that the proper line voltage is available to the power supply.

Localize Trouble Determine the trouble symptom. Use the wiring diagrams in the Schematic Package Supplement to determine which assemblies or major circuits could cause the trouble. Perform the self-test procedure provided in Chapter 2.

Visual Check Visually check for obvious problems in the portion of the game where a trouble is suspected. For example, check for loose or defective solder connections, integrated circuits loose in their sockets, loose cable connections, broken wires, damaged printed-circuit boards or components.

Check Individual Components

—\—— WARNING —~,— To avoid electrical shock, turn the game off before removing or replacing components.

CAUTION Transistors and integrated circuits soldered in place are difficult to remove without damaging the printed circuit board or component. Be extremely careful when removing these components.

Check soldered-in components by disconnecting one end to isolate the measurement from the affects of the surrounding circuitry, Often, direct substitution is the most practical way to determine ifa component is faulty, However, eliminate the possibility of some other circuit problem existing which could damage the substitute component.

Repair the Assembly Repair or replace the defective part. Refer to Chapter 4, Maintenance and Repair for special repair and replacement procedures. Check for proper operation of any repaired. circuit.

Page 25

Maintenance

The maintenance procedures provided in this chapter are for those items which are subject to the most severe use. ‘To assure the maximum trouble-free operation from this game, Atari recommends that periodic routine maintenance be performed on the game components described in the following procedures. How often routine maintenance is performed depends upon the game environment and frequency of play.

WARNING To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

Chapter 4

Page 26

Maintenance

Cleaning Requirements

The game cabinet and display shield may be cleaned with any non-abrasive household cleaner. The coin mechanism should be cleaned periodically with hot or boiling water anda mild detergent. A toothbrush may be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, flush thoroughly with hot or boiling water and blow out all the water with compressed air. Compressed air is also recommended for cleaning dust from the interior of the cabinet.

Opening the Control Panel

  • Unlock and open the coin door. Reach up through the opening to the top of the control panel and release the two spring-draw latches.
  • Close the coin door.
  • Lift the control panel at the top edge and tilt it toward you. The control panel has foam tape on it. Make sure the tape is in good condition.

Pushbutton Leaf Switches

  • With the control panel open, adjust the leaf switch contacts for a narrow gap. When a pushbutton is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don't burnish the contacts. To clean them, use electrical contact cleaner.
  • To replace a leaf switch, remove the screw with a Phillips-head screwdriver.
  • Toreplace the switch pushbutton, turn the stamped nut with a wrench ina counterclockwise direction, as seen from the inside of the control panel. The ringon the outside of the control panel should not spin.
  • Reinstall the pushbutton switch. Reconnect the harness wires to the switch terminals.

Lighted Midi Trak-Ball Assembly

Routine maintenance of the Midi Trak-Ball assembly consists primarily of inspecting the roller shafts for excessive wear and periodically lubricating the bearings.

Removing the Midi Trak-Ball

Open the control panel as previously described and disconnect the wires from the Midi Trak-Ball lamp socket. Disconnect the harness at the six-pin connector,

  • Remove the four nuts and carriage bolts that secure the Midi Trak-Bail assembly to the control panel (see Figure 4-1).

4-2 Crystal Castles

Disassembling the Midi Trak-Ball

To disassemble the Midi Trak-Ball after it has been remoyed from the control panel, remove the six screws that secure the upper and lower frames (see Figure 4-1). Lift off the upper frame. The Midi Trak-Ball can now be disassembled.

Inspecting the Midi Trak-Ball With the Midi Trak-Ball disassembled, inspect the roller shafts and the idler shaft for excessive wear (see Figure 4-2). If the wear band exceeds % inch, replace the roller shaft as described in steps 2-6 or replace the idler shaft as described in steps 7-10.

  • To replace a roller shaft, first remove the roller shaft from the lower frame.
  • Remove the metal encoding wheel by loosening the socket-head screw, flat washer, and split-lock washer. Remove the encoding wheel and bearings.
  • Remount the bearings and encoding wheel ona new roller shaft.
  • Tighten the encoding wheel by inserting a %-inch diameter pin or screwdriver through the hole in the shaft. Tighten the socket-head screw with an Allen wrench.
  • Reinstall the roller shaft in the lower frame.
  • To replace the idler shaft, first remove the idler shaft from the lower frame.
  • Remove the bearings from the ends of the idler shaft.
  • Remount the bearings on a new idler shaft.
  • Reinstall the idler shaft in the lower frame.

Lubricating the Midi Trak-Ball Lubrication of the Midi Trak-Ball assembly should be performed every three months Or 6,000 credits (as counted on the coin counter). To lubricate, place two drops of a light-duty oil, such as 3-In-One oil, on each of the six ball bearings shown in Figure 4-1.

Replacing the Coupler PCB To remove the Coupler PCB, first disassemble the Midi ‘Trak-Ball. Lift the PCB out ofits slot. Carefully disconnect the red connector and remove the PCB.

  • To reinstall the Coupler PCB, place the PCB in the slot in the lower frame and reconnect the red connector.
NOTE When you reinstall the Coupler PCB, make sure that the metal encoding wheel is not bent or damaged. Be sure the encoding wheel turns freely between the two halves of the radial optical coupler.
Page 27

Crystal Castles Maintenance

Hole in Roller Shatt

Encoding wi Lubricate Here ‘ee Six Places Midi Trak-Bail “®@ pen Allen Wrench

Socket-Head Idler Shaft Rotter Shatt Screw

Vertical-Motion PCB: Black, Red, Yellow, Encoding Wheel and Green Wires

Flat Washer ee I Red Connector Split-Lock at {

Screw ry Horizontal-Motion PCB:

Blue, Violet, Red, d Optics! Coupler and Black Wires

Figure 4-1 Midi Trak-Ball™ Assembly and Lubrication

Page 28

Maintenance

Reassembling the Midi Trak-Ball

  • Install the upper frame of the Midi Trak-Ball over the assembly. Be sure that each Coupler PCB is engaged in the slots of the upper frame.

N Replace the six screws that secure the upper and lower frames together.

  • Remount the Midi Trak-Ball assembly to the control panel using the four nuts and carriage bolts. Reconnect the six-pin connector of the harness.
  • Reconnect the wires to the lamp.

Yeinch

Figure 4-2 Excessive Shaft Wear

Video Display Shield

To remove the video display shield, first open the control panel as previously described. Then, grasp the lower edge of the shield and slide it down into the cut-out area of the cabinet below the display. Tip the upper edge of the shield forward. Lift the shield up and out of the cabinet. To replace the video display shield, set the bottom edge of the shield into the cut-out area of the cabinet below the display. Tip the shield back into the cabinet. Grasp the lower edge of the shield and slide it up until the upper edge engages the retaining slot. Push the shield against the bezel.

Speaker Grille Assembly

To replace either of the audio speakers in this game, you must first remove the speaker grille assembly from the game cabinet.

Removing the Speaker Grille Assembly

  • Remove the 3 socket-head screws and 6 flat washers that secure the attraction panel assembly to the cabinet (see Figure 4-3). Lift the attraction panel assembly up and out of the cabinet. Crystal Castles

Disconnect the fluorescent light harness at the 3-pin connector (see Figure 4-3). Remove the 2 Phillips-head screws that secure the attractionsSpeaker shield (see Figure 4-3). Slide the shield out of the cabinet. Disconnect the speaker wires. Remove the video display panel as previously described. Remove the display bezel from the cabinet by removing the foose cross cleat with attached display bezel. Remove the bolt and washers that secure the speaker grille assembly to the game cabinet. Carefully slide the speaker grille assembly out of the cabinet.

Speaker Replacement

L With the speaker grille assembly out of the game cabinet, remove the 4 nut/washer assemblies, washers, and carriage bolts securing each speaker to the speaker grille assembly (see Figure 4-4). Mount the new speaker to the speaker grille assembly with the 4 nuts and carriage bolts. Be sure to position the speaker with its connections toward the center of the speaker grille assembly.

Reinstalling the Speaker Grille Assembly

B Carefully reinstall the speaker grille assembly into the cabinet. Secure the speaker grille assembly to the cabinet with the bolt and washer (see Figure 4-3). Align the front grille surface parallel with the leading edge of the Shield retaining panel. Slide the top edge of the video display bezel into the retaining slot. Lift the display bezel and position its bottom cleat into the cabinet cut-outs. Replace the video display shield as previously described. Reconnect the speaker wires as shown in Figure 4-4. Position the attraction/speaker shield with its cut-out toward the front of the cabinet and its textured side facing down. Replace the 2 Phillips-head screws that secure the attraction/speaker panel to the cabinet. Reconnect the 3-pin connector on the fluorescent light harness. Reinstail the attraction panel by pushing down and forward across the top of the panel until the mounting, bracket engages with the bracket on the speaker grille. Replace the 3 socket-head screws and 6 fiat washers.

Page 29

Crystal Castles Maintenance

Attraction Panel Assy.

Attraction/Speaker Shield

Speaker Grille Assy.

Display Shield

—— Nut

Speaker Grille Washer

Carriage Bolt

Figure 4-4 Speaker Removal

Page 30

Maintenance

Removing the ATARI CRT Assembly

4-6 The cathode-ray tube (CRT) assembly may implode if struck or dropped. Shattered glass can cause personal injury within a6-foot radius. To reduce the risks Of injury to people or of damage to the game components, we recommend that two people perform the following remoyal procedures.

Remove the rear access panel from the cabinet. Discharge the high-voltage from the CRT before proceeding. The video display contains a circuit for discharging the CRT high voltage to ground when power is removed. However, to make certain, always discharge the CRT as follows: a. Attachoneend ofa large, well-insulated, 18-gauge jumper wire to ground. b. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. c. Wait two minutes and repeat part b.

Nut/Washer

Display Shield a Crystal Castles

Disconnect the following wiring (see Figure 4-5): ® Disconnect the anode lead from the CRT. ¢ Disconnect the degaussing coil connector from the Deflection PCB, © Disconnect the yoke connector from the Deflection PCB.

  • Disconnect the DAG spring connector from the Deflection PCB and the Neck PCB. ¢ Disconnect the focus connector, Carefully remove the Neck PCB from the CRT neck pins. Remove the video display shield as previously described. Remove the dislay bezel from the cabinet by sliding its lower edge and attached wood cleat out of the cabinet cut-out. Carefully remove the 4 nut/washer assemblies that secure the CRT to the cabinet (see Figure 4-5). Carefully lift the CRT from the front of the cabinet and remove the CRT. Replace the CRT assembly in the reverse order of this procedure.

DAG Spring Connector CRT Neck PCB

Figure 4-5 CRT Removal

Page 31

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-ptefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99; then 000598through approximately 201000: When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 5

Page 32

Illustrated Parts List Crystal Castles

Fluorescent Tube & A040101-01 Attraction Panel Cabinet Assy. See Figure 5-4

‘Speaker Assy. See Figure 5-5 039317-01 Display Shield ‘A200001-01 ATARI CRT Assy. 92-049 Electrohome Display or 13903-1004 201018-01 Matsushita Display or Mounting Bracket—not shown 92-055 A200001-01 Wells-Gardner Display Atari CRT Assy.

Control Panel See Figure 5-2 178034-024

TMolding

Trak-Ball Assy. See Figure 5-3

Coin Door Assy.: See Figures 5-7 or 5-8

| Assy. ay Face Manuals, Schematics, & Self-Test Label— See parts list on 78-3201 following page Glide

Figure 5-1A Cabinet-Mounted Assemblies US-Built Cabinet A040100-01 A

5-2

Page 33

Crystal Castles Illustrated Parts List

037332-01 Ventilation Grille

EMolding

EMI Cage See Figure 8-9

Game PCB See Figure 5-11

Access Panel

A201022-01 Deflection PCB Assy. EMI Shield PCB See Figure 5-10

A040695-01 Coin Box Enclosure Main Harness Assy.

Regulator/Audio I! PCB Power Supply See Figure 5-12 See Figure 513

A040587-01 Power On/Off Switch Assy, 009992-01 On/Ofi Switch Cover

\ Power Cord

Figure 5-1A_ Cabinet-Mounted Assemblies, continued US-Built Cabinet A040100-01 A

Page 34

Miustrated Parts List Crystal Castles

Cabinet-Mounted Assemblies US-Built Cabinet Parts List

Part No. Description A200001-01 19-Inch ATARI Color Raster-Scan Cathode-Ray Tube (CRT) Assembly—includes: A201020-01 Neck PCB Assembly A201022-01 Deflection PCB Assembly A201024-01 Color Raster Harness Assembly A201092-01 CRT Assembly A038881-01 Lock Assembly (for rear access pane!) Acceptable substitute is part no, A038881-03 A040101-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A040586-01 Strain-Relief Power Cord (U.S. and Canada) A040587-01 Power On/Off Switch and Mounting Plate Assembly A040695-01 Main Harness Assembly A040696-01 Power Harness Assembly The following seven tems are technical information supplements to this game: SP-241 Crystal Castles Schematic Package SF241-01 Crystal Castles Label with Self-Test Procedure and Option Switch Settings TM-241 Crystal Castles Operators Manual with Illustrated Parts List One of the following manuals will apply to the video display in your game: TM199 Service Manual for 19-Inch Atari Color-Raster Display (use with part no. A039650-01) or

TM-160Service Manual for 19-Inch Electrohome Color-Raster Display(use with part no. 92-049)

or

TM-201Service Manual for 19-Inch Wells-Gardner Color-Raster Display(use with part no. 92-055)

or

TM-220Service Manual for 19-Inch Matshushita Color-Raster Display(use with part no. 139003-1004)

78-3201 Adjustable Glide 009992-01 Power On/Off Switch Cover 037332-01 Ventilation Grille 038091-01 Molded Coin Box

038870-01 Coin Box Enclosure 039317-01 Video Display Shield 040129-01 Rear Access Panel (does not include lock) 178013-001 Spring Draw Latch 178034-024 %4-Inch Black Plastic TMolding 178034-026 +44-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster 201018-01 Mounting Bracket (for ATARI display only, not shown)

Page 35

Crystal Castles Ilustrated Parts List

177010-240 75-5148B Locknut Bolt weave 478030-004 Nut Red Pushbutton

160013-001 Leaf Switch & Button Holder

Midi Trak-Ball Assy. 179125-001 See Figure 5-3 Grounding Clip 040107-01 Control Panel with Decal A040581-01. Harness 040113-01 Players may receive an electrical comiire! shock if this control panel is not pro- 040139-03 perly grounded! Atter servicing any De eee ecal—Not Shown parts on the panel, make sure that the grounding clipis securedio the metaltab on the inside of the cortrol panel

Figure 5-2 Control Panel Assembly A040106-01 A Parts List

Part No. Description

A38038-01 Lighted Midi Trak-Ball™ Assembly A040107-01 Control Panel with Decal A040581-01 Control Panel Harness Assembly 75-5148B #10-24 Black Carriage Bolt

75-9910NO %-Inch x 11 Stamped Nut 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, 4 -inch Wide x 4-Inch Thick (24 inches required, not shown) 040113-01 Control Panel 040139-03, Control Panel Decal (not shown) 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 177010-240 #10-24 Hex Locknut 178030-004 Red Pushbutton Assembly 179125-001 Grounding Clip (Acceptable substitute is part no. 179074-010)

5-5

Page 36

Crystal Castles Illustrated Parts List

176010-106 038039-01 Screw Upper Frame

038043-02 Midi Trak-Bal!

035937-01 ae Ball Bearing

038042-01 Idler Shaft 038041-01 Roller Shaitt

035938-01 Encoding Wheel Qs is 75-0145 ‘ Fiat Washer i 75-0448 BY Spiit Lock Washer |" © 72-8406 at Socket-Head Screw 4036096-01 Harness Assy.

139002-001 Optical Coupier—Hidden, From View

038040-01 Lower Frame ~~

A035220-02 170000-002 __—— > Coupler PCB Assy. Lamp

179173-001 oO : Sooke jee

Figure 5-3 Lighted Trak-Ball™ Assembly A038038-02 B

5-6

Page 37

Crystal Castles Alustrated Parts List

Lighted Trak-Ball™ Assembly Parts List

Part No. Description A036096-01 Harness Assembly A035220-02 Coupler PCB Assembly (includes Radial Optical Coupler) 72-8406 #4-40 x &-Inch, Hex Socket-Head Steel Machine Screw 75-0148 #4 Flat SAE-Standard, Zinc-Plated Steel Washer 75-0445 #4 Split-Lock, Zinc-Plated Steel Washer 035937-01 Ball Bearing (6 per assembly) 035938-01 Etched Encoding Wheel 038039-01 Upper Black Plastic Frame 038040-01 Lower Black Plastic Frame 038041-01 Rollex Shaft 038042-01 Idler Shaft 038043-02 Midi‘Trak-ball (3-inch diameter) 170000-002 Wedge-Base 6.3 V Lamp 176010-106 #8 x %-Inch Cross-Recessed, Pan-Head, Zinc-Plated Steel Screw 179173-001 Wedge-Base Lamp Socket

5-7

Page 38

Illustrated Parts List Crystal Castles

040136-01 A040125-01 Attraction Shield Attraction Hood 99-11009 99-11003 179125-001 Stayer Grounding Clip

179035-001 Tube Holder

Harness 142028-001 Transformer

040140-03 040115-01 ‘Attraction Panel Light Bracket with Decal

salon 79-561816P el] \ Attraction Bracket 79-501016 r304 99-1006 Tube Tab

Figure 5-4 Fluorescent Tube and Attraction Panel Assembly A040105-01 A Parts List

Part No. Description

A005493-01 Fluorescent Light Harness Assembly, A037540-01 Ground Wire with Ring Lug (not shown) A040125-01 Attraction Hood Assembly 70-304 18-Inch, 15Watt, Cool White Fluorescent Tube

78-6900404 Vinyl Foam Single-Coated Adhesive Tape, 4 -Inch Wide x %4-Inch Thick (24 inches required, not shown) 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11006 Fluorescent Tube Locking Tab (consists of two pieces) 99-11003 Fluorescent Tube Starter

99-1009 Starter Socket 040115-01 Fluorescent Light Mounting Bracket 040116-01 Attraction Panel Mounting Bracket 040136-01 Attraction Panel Shield

040140-03 Attraction Panel with Decal 142028-001 60 Hz, 118 V, Ballast Transformer 176015-110 #10 x %-Inch, Cross-Recessed Pan-Head Screw 179035-001 2-Pin Fluorescent Tube Holder 179125-001 Grounding Clip (Acceptable substitute is part no. 179074-010)

5-8

Page 39

Crystal Castles Ilustrated Parts List

148001-017 75-99511 —*—NutWasher

'75-010S Washer

040114-01 Weldment

040118-01 Shield 040141-03 75-5112B 78-6900404 Decal—Not Shown Bolt Tape—not shown

Figure 5-5 Speaker Assembly A040108-01 A Parts List

Part No. Description 040114-01 Speaker Grille Weldment 040118-01 Glass Shield for Decal 040141-03 Decal (not shown) 75-0108 #10 Flat Washer

75-5112B #10-24 x 0.75-Inch Black Carriage Bolt 75-9951] #10-24 Nut/Washer 78-6900404 Vinyl Foam Single-Coated Adhesive Tape, 4-Inch Wide x 4-Inch Thick (13 inches required, not shown) 148001-017 6x 9-Inch Oval, 8 2, 6-Ounce, Shielded High-Fidelity Speaker

5-9

Page 40

Ulustrated Parts List Crystal Castles

179125-001 Grounding Cio

75-9910WO Nut

00246501 Coin Counter sot Auxiliary Coin Switch

69-001 Selt-Test Switch 178070-001 Votume Control Knob

WARNING Betore removing or repairing the utility panel, turn the game off. Players may receivean electrical shock ifthe utility panel is not properly grounded! After servicing ary parts on the pane’, make sure that the ground wire is firmly attached to the bracket. 19-9032 Volume Controt
NOTE Only the Ireland-built cabinet has two. coin counters.

Figure 5-6 Utility Panel Assembly A038002-01 H Parts List

Part No. Description

A002465-01 6V Coin Counter A037779-03, Weldmient Enclosure Assembly (not shown) A038004-01 Utiliry Panel Harness 19-9032 Volume Control

62-041 SPDT Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 75-9155 #6-32 Hexagon Machine Nut 75-9910W0 1%2-Inch Stamped Nut

038003-01 Utility Panel 038781-01 Weldment (not shown) 176018-002 #6-32 x ¥-Inch Thread-Forming Pan-Head Screw 178070-001 Volume Control Knob 179125-001 Grounding Clip

5-10

Page 41

Crystal Castles Illustrated Parts List

170000-001 (Lamp)

  • a 179047-001 9915023 (Lamp \y “P (Base Plate)

a“ a 99-15056 (Screw for Bezel) 99-15026 (Coin Inlet)

99-15025 (Coin inlet)

75-9148 (Hex Nut) (Hex Nut) 7

(Lock Wash.)

(Switch)

Figure 5-7 Vertically Mounted Coin Door 171034-xxx A

5-11

Page 42

Illustrated Parts List

(A037542-01 Harness—not shown

99-15063 Screw Crystal Castles

99-15067. Lock Assy. 99-15038 Bezel for Button

99-1501 thru 99-15011 Return Button

99-15052 Spring for Button

99-15067 Lock Assy

038091-01 Coin Box

oe

99-15072 Door Frame

99-15073 Upper Door

99-15074 Lower Door

171034-001 — U.S. 25¢/25¢ Coln Door 171034-003 — Canadian 25¢/25¢ Coin Door 174034-005 — U.K. 10 P/50 P Coin Door

Figure 5-7 99-15070 Doors and Frame 99-15039 Bezel for Cover

99-15066 Screw

171034-011 — German 1 DM/5 DM Coin Door 171034-006 — U.K. 20 P/S0 P Coin Door 171034-015 — French 2 Frit Fr Coin Door 171034-009 — German 2 DM/1 DM Coin Door 171034-010 — German 2 DM/5 DM Coin Door

Vertically Mounted Coin Door, continued 171034-xxx A

Page 43

Crystal Castles Tilustrated Parts Lisi

Vertically Mounted Coin Door Parts List

Part No, Description

A037542-01 Harness Assembly 72-14128 #4-40 x %-Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9148 #4-40 Stee\ Machine Hex Nut

75-34145 #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with US. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate

99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate

99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British i0 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate

99-15023 Base Plate 99-15025 Left Half of Coin Iniet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box

99-15023 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button

99-15039 Metal Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15042 Coin Switch for US, 25¢ 99-15052 Spring for Coin Return Button

99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 #4-40 x 4¢-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover

99-15063 Screw for Hinge 99-15066 Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame

99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door

99-45075, Switch Adjuster 038091-01 Coin Box (Not included in assembly—Acceptable substitute is part number A037491-01) 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base

Page 44

Illustrated Parts List Crystal Castles

171008-035 99-10140 Coin mechanism Panel assy.

99-10116

99-10152 Right coin inlet 99-10096 Fastener 75-9448 Locknut

99-10151 Left coin inlet

99-10080 Lamp socket .

70-11-47 p > Lamp ae }

6G 99-10104 Bar retainer 72.9408 . ‘Screw . , 99-10147 Z Harness

99-10154 Bracket assy &

99-10042 thru 99-10045 Coin switch assy 99-10153 > Coin return box ~ ~~ Sy $e.

Coin switch _— —~ bo A 99-10150 ~ NN L > Switch cover 99-10075 thru 99-10078 M™ ‘Switch wire 99-1008 7514125 Retainer Screw

Figure 5-8 American-Made Coin-Door Assembly 171027-001 A

5-14

Page 45

Crystal Castles illustrated Parts List

99-10148 (Lock assy.)

9910142 (Button housing)

99-10134 sarorrg } Coven (Button assy) ) 99.1911 (Button)

99-10115, (Spring)

99-10141 (Coin return cove:)

9910117 . (Coin return door)

“ 99-10144 Z |<—(Channel clip)

72-JA1405B (Screw) 99-10149 (Service door)

038091-01 (Coin box) 99-10143 (Frame)

Figure 5-8 American-Made Coin-Door Assembly, continued 171027-001 A

5-15

Page 46

Illustrated Parts List

American-Made Coin-Door Assembly Crystal Castles

Parts List

Part No. Description

171006-035 Metal Coin Mechanism for US. $.25 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x %-Inch Truss-Head Screw 72-HA1404C #4-40 x %4-Inch Pan-Head Screw 72-JAI405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x %-Inch Pan-Head Screw 75-9448, #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire (included in coin switch assembly) 9910076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-1081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-1016 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 9910118 Amber Coin Return Button 99-1019 Amber Coin Button for US. $.25 9910134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145, Offset Cam 99-10146 Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10148 Lock Assembly 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly

5-16

Page 47

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 48

Iitustrated Parts List Crystal Castles,

NOTE The Federal Communications Commission requires that the game PCB 176015-112 be housed in the EMI cage with the Screw EMI Shield PCB attached

Crystal Castles Game PCB See Figure 5-11

Game PCB

A037701-02 EMI Cage

72-1404F 175009-221 Screw Washer EMI Shield PCB 178044-242 See Figure 5:10 Grommet EMI Shield PCB 178045-442 72-1604F Fastener Screw Grounding clip not shown

175004-708 Washer 176015-112 175004-708 Washer

176015-112 Screw

Regulator/Audio || PCB See Figure 5-12 A201022-01 Deflection PCB—used only with the Atari Video Display

Figure 5-9 Electromagnetic Interference (EMI) Cage Assemblies and PCB Mounting Hardware

Page 49

Crystal Castics:

EMI Cage Assemblies and PCB Mounting Hardware Parts List Illustrated Parts List

Part No. Description A201022-01 Dellection PCB-used only with the Atari Video Display A035435-01 Regulator/Audio IT PCB (Acceptabie substitute is part no. A035435-02) A037701-02 EMI Cage (includes guide)

A037430-06 EMI Shield PCB-includes: 72-1404F #4-40 x M4 -Inch Cross-Recessed Steel Screw 037873-01 Spacer 175009-221 Plastic Washer 178044-242 Grommet 178045-442 Snap-In Fastener

A039574-21 Crystal Castles Game PCB 72-1604F #632 x %4-Inch Cross-Recessed Pan-Head Screw 175004-708 #8 Fiat Fiber Washer 176015-112 #10 x 34-Inch Cross-Recessed Pan-Head Screw

SAD

Page 50

Mlustrated Parts List

NOTICE TO ALL PERSONS RECEIVING THiS DRAWING

IAL: Reproduction fortxdden without the spectic wrt fa pamseon cist, ine, Sunnyeale Gh Ts drang ony conditionally ssued, and nerther receipt nor possession there0l con- {ers or transfers any right in, or licenseto use, the subject matter of the drawing or any design or echnical rtormalion shown thereon, ‘nor any right to reprcduce this érawing oF any part thereof. Except Jor manufacture by vendors of Atari Inc..and‘or manufacture under the corporation’ witten icense. no rght isgrarted torepreduce ns Grawingor the subject mater thereof, uniess by written agreement ‘with OF wnitten permission from the corporation

OC! ooce c3

a-C.8 COrCS

2e-C(S oCcte C17 C18 cia

ooce!

fl

Figure 5-10 EMI Shield PCB Assembly A037430-06 A Crystal Castles

Page 51

Crystal Castles Mlustrated Parts List

Electromagnetic Interference Shield PCB Parts List

DesignatorDescriptionPart No.

Capacitors

CI-C30.1 pF +80%, -20%, 50 V Ceramic Capacitor122002-104
C8.Co0.01 pF, +80%, -20%, 25 V Minimura, Axial-Lead Ceramic Capacitor122005-103
as470 pF, 100 V Ceramic Capacitor(Acceptable substitute is part no. 122013-471)122016-471
C160.1 uF, +80%, -20%, 50 V Ceramic Capacitor122002-104
ci?1000 pF, +5%, 100 V Axial-Lead Ceramic Capacitor(Acceptable substitute is122016-102

part no. 122002-302)

cls0.1 uF, +80%, -20%, 50 V Ceramic Capacitor122002104
clo0.01 pE, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103,
C21OL wR +80%, -20%, 50 V Ceramic Capacitor122002-104
€26-C290.01 aE, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103,
C34, C35470 pF, 100 V Ceramic Capacitor(Acceptable substitute is part no. 122013-471122016-471
36, C371000 pF, 45%, 100 V Axial-Lead Ceramic Capacitor(Acceptable substitute is122016-102

part no. 122002-102)

C380.01 pF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
€39,C40O.1 uF, +80%, -20%, 50 V Ceramic Capacitor122002-104
C43-C480.01 pF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
500.01 uE, +80%, -20%, 25 V Minimum, Axiat-Lead Ceramic Capacitor122005-103
C54,C550.01 pF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
CS87-C61L0.01 pF, + 80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103

Connectors

P1924-Pin Connector179073-024
P2044Pin Connector(Acceptable substitute is part no. 179046-044)179073-044

Miscellaneous Spacer 037873-01 #4-40 x Y4-Inch Cross-Recessed, Pan-Head Steel Machine Screw 72-1404F Plastic Washer 175009-221 Grommet 178044-242 Smap-In Fastener 178045-442

5-21

Page 52

Crystal Castles Mlustrated Parts List

UI: co ces sez WIR Goce) @ Gees prevabves [za jie] SES | a CHIR Tez}

» leoazaerot Ta GLY Coase a : eee, oes) fers = S221] Sea] swer Pearl 5]

Figure 5-11 Crystal Castles PCB Assembly A039574-21 A

5-22

Page 53

Crystal Castles Mlustrated Parts List

Crystal Castles PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

ca0.1 pF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
c2100 pF, 100 V, Dipped Fixed Mica Capacitor128002-101
ror’39 pF, 100 V, Dipped Fixed Mica Capacitor128002-390
C40.1 pF, +80%, -20%, 50 V, Ceramic Capacitor122002104
cS0.01 pF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
c70.01 pF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122008-103
c8-C130.22 pF +20%, 25 V Axial-Lead Ceramic Capacitor122004-224
Cl4-C210.01 pF, +80%, -20%, 25 V Minimum, Axial-lead Ceramic Capacitor122005-103
€22, C23,0.1 pE, +80%, -20%, 50 V, Ceramic Capacitor122002:104
C25-C290.1 AE, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C300.01 uF, + 80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
C310.22 pF, +20%, 25 V, Axial-Lead Ceramic Capacitor122004-224
C32-C340.1 4E, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C35,0.01 pF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103,
C360.1 pF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C370.22 pF, +20%, 25 V, Axial-Lead Ceramic Capacitor122004-224
C38, C390.1 pF, +80%, -20%, 50 V, Ceramic Capacitor122002-104
C400.22 uF, 25 V, +20%, Axial-Lead Ceramic Capacitor122004-224
Cl, C42100 uF, 25 V, Axial-Lead Aluminum Electrolytic Capacitor24-250107
C43-C850.1 pF, +80%, -20%, 50 V, Ceramic Capacitor122002-104

Diodes

CRI500 mW, +5%, 8.2 V, Zener Diode32-IN756A
CR2Red Light-Emitting Diode38-MV5053

Integrated Circuits

1BLine Driver/Receiver Integrated Circuit37-7418244
IcLine Driver/Receiver Integrated Circuit37-74LS244
1DLine Driver/Receiver Integrated Circuit37-7418244
IFROM Integrated Circuit136022-XXX
yROM Integrated Circuit136022-XXX
IKROM Integrated Circuit136022-XXX
ILROM Integrated Circuit136022-XXX
INROM Integrated Circuit136022-XXX
IP741833 Integrated Circuit.137239-001
IR74LS33 Integrated Circuit137239-001
1sHex Inverter Integrated Circuit37-74L504
2DMicroprocessor Integrated Circuit90-6013
2E‘Tri-State Octal Bus Transceiver Integrated Circuit37-74LS245
2FLine Driver/Receiver Integrated Circuit37-T4L8244
2HQuad Dat Selector/Multiplexer Integrated Circuit37-74L8257
zyLine Driver/Receiver Integrated Circuit37-7418244
2KQuad 2-input NAND Gate Integrated Circuit37-74800
2LQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
2MQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
2NQuad Data Selector/Multiplexer Integrated Circuit37-74LS157

(continued on next page)

Page 54

Hlustrated Parts List Crystal Castles

Crystal Castles PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
2PQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
2kDual 2-4 Decoder/Multiplexer Integrated Circuit377415139
3DCustom Audio Integrated Circuit€012294-01
3E‘Tri-State Octal Bus Transceiver Integrated Circuit37-TALS245,
3F‘Tri-State Octal Bus Transceiver Integrated Circuit37-TALS245
3H‘Tri-State Octal Bus Transceiver Integrated Circuit377418245
3KVertical Scroll Integrated Circuit1373214111
3LUp/Down Counter Integrated Circuit37-74LSIOL
3MUp/Down Counter Integrated Circuit37-74LS191
3NUp/Down Counter Integrated Circuit37-74LSI91
3PUp/Down Counter Integrated Circuit37-74L8191
BRQuad 2-Input OR Gate Integrated Circuit37-74LS32
4CTri-State Octal Bus Transceiver Integrated Circuit37-7415245
4DTri-State Octal Bus Transceiver Integrated Circuit37-7ALS245,
4E16K X 4 RAM Integrated Circuit137323-001
4F16K X 4 RAM Integrated Circuit137323-001
4H16K X 4 RAM Integrated Circuit137323-001
4g16K X 4 RAM Integrated Circuit137323-001
4LDual Data Selector/Multiplexer Integrated Circuit37-74153
4MDual Data Selector/Multiplexer Integrated Circuit37TAIS3
ANDual Data Selector/Multiplexer Integrated Circuit37-7413
4PDua) Data Selector/Multiplexer Integrated Circuit37-74153
4RDual 2-4 Decoder/Multiplexer Integrated Circuit37-74L8139
5BQuad Op-Amp Integrated Circuit37-LM324
SEQuad 2-Input OR Gate Integrated Circuit37-7ALS32
SFOctal DJype Flip-Flop Integrated Circuit37-74L8374
5HOctal DType Flip-Flop Integrated Circuit37-74LS374
5)Quad 2-Input, With Storage Multiplexer Integrated Circuit137201-001
5KQuad 2-Input AND Gate Integrated Circuit37-74LS08
5LHex Inverter Integrated Circuit3 7-74LS804
5MQuad 2-Input NAND Gate Integrated Circuit37-7ALS00
SNUp/Down Binary, Synchronous 4-Bit Counter Integrated Circuit137109-001
SPUp/Down Binary, Synchronous 4-Bit Counter Integrated Circuit137109-001
SRQuad 2-Input OR Gate Integrated Circuit37-74LS32
OAQuad 2-Input OR Gate Integrated Circuit37-74832
6B200 ns Tri-Siate Static RAM Integrated Circuit137198-001
6D200 ns Tri-State Static RAM integrated Circuit137198-001
OEQuad Data Selector/Multiplexer Integrated Circuit37-74LS157
OFQuad Data Selector/Multiplexer Integrated Circuit37-74LS1S7
6HQuad Data Selector/Multiplexer Integrated Circuit377418157
6KQuad 2-input NOR Gate Integrated Circuit37-74LS02
OLBus PROM Integrated Circuit136022-109
6M3-8 Line Decoder/Multiplexer Integrated Circuit137177001
ONHex Inverter Integrated Circuit37-TALS04
oP8-Bit Latch Integrated Circuit37-74L8259
ORDual 2-4 Decoder/Multipiexer Integrated Circuit37-741S139
7AOctal D-Type Flip-Flop Integrated Circuit37-74LS374
7B4-Bit Binary, Full Adder Integrated Circuit137204-001

(continued on next page)

Page 55

Crystal Castles Illustrated Parts List

Crystal Castles PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
7C4-Bit Binary, Full Adder Integrated Circuit137204-001
7DDual 4-Input NAND Gate Integrated Circuit37-74LS20
TEHex D-Type Flip-Flop Integrated Circuit37-74LS174
TFHex Inverter Integrated Circuit37-74LS04
7HQuad 2-Input NOR Gate Integrated Circuit37-74S02
aQuad 2-Input OR Gate Integrated Circuit37-74832
7KSynchronous PROM Integrated Circuit136022-108
7LDual D-lype Flip-Flop Integrated Circuit37-74LS74
7M4-Bit Decade Counter Integrated Circuit37-74163
7N4-Bit Decade Counter Integrated Circuit37-74LS160
id4-Bit Synchronous Counter Integrated Circuit37-7ALSIO3A
7R4-Bit Synchronous Counter Integrated Circuit37-74LS163A
8BROM Integrated Circuit136022-XXX
8DROM Integrated Circuit136022-XXX
8EQuad 2-Input Exclusive OR Gate Integrated Circuit37-74LS86
8FQuad 2-Input Exclusive OR Gate Integrated Circuit37-74LS86
8HQuad 2-Input NOR Gate Integrated Circuit37-74802
8yQuad D‘ype Flip-Flop Integrated Circuit37-74LS175
8KQuad 2-Input AND Gate Integrated Circuit37-74LS08
8LDual J-K Flip-Flop Integrated Circuit37-74109
8MUp/Down Counter Integrated Circuit37-7ALS193,
8N8-Bit Latch Integrated Circuit37-7418259
9AQuad 2-Input, with Storage Multiplexer Integrated Circuit137201001
9BShift Register Integrated Circuit37-7ALS194
9CShift Register Integrated Circuit37-TALSI94
9DShift Register Integrated Circuit37-74LS194
9EDual D-Type Flip-Flop Integrated Circuit37-74LS74
oFQuad 2-Input OR Gate Integrated Circuit37-74LS32
oHQuad 2-Input NOR Gate Integrated Circuit37-74LS02
iQuad 2-Input NAND Gate Integrated Circuit37-74LS00
9KDual D-type Flip-Flop Integrated Circuit37-74S74
OL.Dual D-Type Flip-Flop Integrated Circuit37-7874
OMHex Inverter Integrated Circuit37-74804
10A55 ns Tri-Sute Static RAM Integrated Circuit137199-001
10B55 ns Tri-State Static RAM Integrated Circuit137199-001
10C4-Bit Synchronous Counter Integrated Circuit37-74LS1O3A,
10D4-Bit Synchronous Counter Integrated Circuit37-74LS163A
10E4-Bit Synchronous Counter Integrated Circuit37-TALSIOZA
10F4-Bit Synchronous Counter Integrated Circuit37-7ALSIOZA.
10H.Quad 2-Input OR Gate Integrated Circuit37-T4LS32
10Dual J-K Flip-Flop Integrated Circuit37-74109
10KColor PROM Integrated Circuit136022-111
10L4 to 1 Data Selector/Multiplexer Integrated Circuit37-74LS153
10M4 to 1 Data Selector/Multiplexer Integrated Circuit37-74LS153,

(continued on next page)

5-25

Page 56

Illustrated Parts List Crystal Castles

Crystal Castles PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
10NOctal D-lype Flip-Flop integrated Circuit37-74LS273
10R64 x9 RAM Integrated Circuit137322-001
nALine Driver/Receiver Integrated Circuit37-74LS244
iBQuad 2-Input, with Storage Multiplexer Integrated Circuit137201-001
uCLine Driver/Receiver Integrated Circuit37-74L8244
nETrak-Ball interface Integrated Circuit137304-1001
1FQuad 2-Input OR Gate Integrated Circuit37-74LS32
ilHHex Buffer/Driver Integrated Circuit37-7407
1KQuad 2-Inpuc OR Gate Integrated Circuit37-74S32
lil.‘Write PROM Integrated Circuit136022-110
11MDual DJype Flip-Flop Integrated Circuit37-7474
MINHex Buffer/Driver integrated Circuit37-7407
MPHex Buffer/Driver Integrated Circuit377407
HiRDual D-lype Flip-Flop Integrated Circuit37-7418 74
ARDual 5-Input NOR Gate Integrated Circuit37-T48260

Resistors

RI, R210 k@, £5%, 4 W Resistor110000-103
R32200, +5%, % W Resistor0000-221
R4A7kQ, +5%, 4 W Resistor110000-472
RS2200, +5%, 4 W Resistor110000-221
RO1kQ, +5%, 4 W Resistor110000-102
R72209, +5%, %& W Resistor110000-221
R810kQ,+5%, % W Resistor110000-103,
RO270, +5%, 4 W Resistor10000-270
RIO-R122200, +5%, % W Resistor110000-221
RB1kQ, +5%, %4 W Resistor110000-102
R14272, 45%, % W Resistor110000-270.
RIS-RI81k, +5%, 4 W Resistor0000-102
RI9-R24279, £5%, 4 W Resistor110000-270
R25-R3610 k@, +5%, % W Resistor110000-103,
R37-R53.1k@, 5%, 4 W Resistor110000-102
R542200, +5%, %4 W Resistor110000-223
RSS1.2kQ, +5%, %4 W Resistor110000-122
R56-R6O1 kQ, +5%, %& W Resistor110000-102
ROL4.7 kG, +5%, %& W Resistor110000-472
R6222kQ, 45%, % W Resistor110000-223
R6310kQ, +5%, 4 W Resistor110000-103
RO4100@, +5%, % W Resistor110000-101
ROS100.2, +5%, % W Resistor110000-101
RO6-R6D1kQ, +5%, ‘4 W Resistor110000-102
R704.7 kQ, +5%, “ W Resistor110000-472
R7110 kQ, +5%, % W Resistor110000-103
R7222 kQ, +5%, 44 W Resistor110000-223
R73-R741002, £5%, % W Resistor110000-10!

5-26 (continued on next page)

Page 57

Crystal Castles Illustrated Parts List

Crystal Castles PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R75-R781kQ, +5%, % W Resistor110000-102
R794.7kQ, +5%, %& W Resistor110000-472
R8010 kQ, +5%, %& W Resistor110000-103
R8122 kQ, +5%, 4 W Resistor110000-223
R82, R831000, +5%, % W Resistor110000-101
R84-R913.3kQ, +5%, %& W Resistor110000-332,
R92, R93470 2, 25%, % W Resistor110000-471
R95-R994700, +5%, % W Resistor110000-471
R100, R1611k@, 5%, 4 W Resistor110000-102
R103—-R1071kQ, +5%, 4 W Resistor110000-102
RIO82200, +5%, 4 W Resistor110000-221
R1091kQ, +5%, 4 W Resistor110000-102
RUO-R1210k, +5%, 4 W Resistor110000-103
RI3-RU51k@, +5%, 4 W Resistor110000-102
RIIG6-Ri18470 Q, +5%, 4 W Resistor110000-471
Rd220, +5%, 4 W Resistor110000-221
Ri201kQ, +5%, % W Resistor110000-102
R121, R122100 kQ, +5%,W Resistor110000-104
R123,62 kQ, +5%, 4 W Resistor110000-623
R124--R127TkQ, 45%, 4 W Resistor110000-102
R128220.2, +5%, % W Resistor110000-221
RI291kQ. +5%, %& W Resistor110000-102
R1302.2kQ, +5%, & W Resistor110000-222
R131, R132100 kQ, +5%, %& W Resistor110000-104
R1332.2 kQ, +5%, 4 W Resistor0000-222
R134100 kQ. £5%, 4 W Resistor110000-104
R35150 2, +5%, % W Resistor110000-151
R136-R1521kQ, +5%, 4 W Resistor110000-102

Sockets

IF28 Contact, Medium-Insertion-Force IC Socket79-42C28
y28 Contact, Medium-Insertion-Force IC Socket79-42C28
1K28 Contact, Medium-Insertion-Force IC Socket79-42C28
IL28 Contact, Medium-Insertion-Force IC Socket79-42C28
IN28 Contact, Medium-Insertion-Force IC Socket79-42C28
2D40 Contact, Medium-Insertion-Force IC Socket79-42C40
3B40 Contact, Medium-Insertion-Force IC Socket79-42C40
3D40 Contact, Medium-Insertion-Force IC Socket79-4240.
4A18 Contact, Medium-Insertion-Force IC Socket79-42C18
4B18 Contact, Medium-Insertion-Force IC Socket79-4218
8B28 Contact, Medium-Insertion-Force 1C Socket79-42C28
8D28 Contact, Medium-Insertion-Force IC Socket79-42C28
JOR28 Contact, Medium-Insertion-Force IC Socket79-42C28

(Continued on next page)

Page 58

illustrated Parts List Crystal Castles

Crystal Castles PCB Assembly Parts List, continued

DesignatorDescriptionPart No.

Transistors

QI-Q3350 miW, 60 V, Switching NPN Transistor34-2N3904
Q41 W, 40 V, PNP Transistor33-2N3906
Q5350 mW, 60 V, Switching NPN Transistor33-2N3904
Q61 W, 40 V, PNP Transistor33-2N3906
Q7350 mW, 60 V, Switching NPN Transistor34-2N3904
Q81 W, 40 V, PNP Transistor33-2N3906
Qo350 mW, 60 V, Switching NPN Transistor34-2N3904
Q10-Q128A, 80 V, Darlington, NPN Transistor34-2N6044

Miscellaneous Test Points (Acceptable substitute part number 020670-01) 179051-002 Nylon Snap-In Fastener 81-4302

YI10-MHz Crystal90.123
8R‘Toggle DIP Switch66-14PIT
Wh100 pH, +10% Inductor141002-001
12-140.29 @, 1.0 gH, +10% Peaking Coil Inductor141007-001
Page 59

illustrated Pacts List Crystal Castles

NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING

CONFIDENTIAL: Reprocucion fortidden withoutine specific witten permission of Alar, Inc. Sunnyvale, CA, This diawing is only sued, and neither receipt ior possession thereof con-

~\ ( SOENZ eo

co 33CO4F 35V + m [8] (TH Inacoz

rb Ls

12 Regulator/Audio II PCB Assembly Figure 5 A035435-01 G

5-29

Page 60

Tilustrated Parts List

Regulator/Audio II PCB Assembly Crystal Castles

Parts List

DesignatorDescriptionPart No.

Capacitors

cl470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C20.001 pF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002102
C30.1 wF, 25 V, Ceramic-Dise Axial-Lead Capacitor29-088
C4470 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24250477
cS.01 wE, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is100015-103,

Part no. 122005-103)

CO0.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor322004-224
c70.001 yF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
ce0.22 wE, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
C9, ClO.3300 pE 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-350338
cil0.1 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor29-088
cl2470 pE, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250477
C31000 pF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor24-250108,
cl4-O1 pE, 25 V Ceramic-Disc Axial-Lead Capacitor (Acceptable substitute is100015-103

part no. 122005-103)

cis0.22 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224
cl60.001 wF, 35 V, Ceramic-Disc Axial-Lead Capacitor122002-102
cl70.22 wF, 25 V, Ceramic-Disc Axial-Lead Capacitor122004-224

Diodes

CRi, CR4Type-1N4002, 1 A, 100 V Silicon Rectifier Diode31-IN4002

Resistors

Rl2702, +5%, % W Resistor110000-271
R3332, 5%, 4 W Resistor110000-330
R41002, +5%, % W Resistor110000-101
RS2.72, +5%, 1 W Resistor0009-027
RO3.9kQ, +5%, % W Resistor110000-392
R77.5k&, +5%, 4 W Resistor110000-752
R81 kQ Vertical PCB-Mounting Cermet Potentiometer (Acceptable substitute is19-315102

part no. 119002-102)

RO2200, +5%, % W Resistor110001-221
RIO10, +5%, 4 W Resistor110000-010
RI100, +5%, 4 W Resistor110000-100
RI2100, +5%, 4 W Resistor110000-101
R13, R1410kQ, +5%, % W Resistor110000-103
RIOD10, +5%, 4 W Resistor110000-010
R20100, +5%, 4 W Resistor110000-100
R212200, £5%, % W Resistor130001-221
R22100 @, 45%, % W Resistor110000-101
R240.19, +3%, 7 W Wirewound Resistor19-100P1015
R27, R281kQ, 45%, 4 W Resistor110000-102
R29, R30100, 25%, %& W Resistor110000-100

(Continued on next page)

Page 61

Crystal Castles

Regulator/Audio II PCB Assembly Iitustrated Parts List

Parts List, continued

Designator Description Part No,

Transistors

Q2TypeTIP32 PNP Power Transistor33TIP32
QBType-2N3085 NPN Silicon Transistor34-2N3055

Miscellaneous

Jo6-Position Connector Receptacle79-58306
y9-Position Connector Receptacle79-58308
Js4-Position Connector Receptacle7958354
Q2Thermally Conductive Silicon Insulator78-10014
Q3Thermally Conductive Silicon Insulator78-16008

Heat Sink 03453101 Yest Point (Acceptable substitute is part no. 020670-01) 179051-001

Page 62

Illustrated Parts List Crystal Castles

‘WARNING Fuse block cover must be in place during game operation A035888-01 Transformer Assembly

A021084-xx Voltage Plugs

29-053 Capacitor 034544-01 Fuse Block Cover

79-4411001 Fuse Post

46-2017002 Fuse

u

vA 03448202 78-70501SC

A035891-02 Fuse Harness ‘Assembly LL Chassis

78-2708 Bushing

‘A034630-01 79-3206 Fiter Assembly Fuse Block 037641-01 46-2014002 Fuses

79-15021001 A035890-01 Terminal Block \ Power Hamess A034629-01 3A-MDA3501 AC Harness Rectifier

Figure 5-13, Power Supply Assembly A037671-01 J

Page 63

Crystal Castles Illustrated Parts List

Power Supply Assembly Parts List

DesignatorDescriptionPart No.
cl27,000 pF, 15 VDC Electrolytic Capacitor29-053
ct2-Inch Diameter Capacitor Mounting Bracket78-7OSOISC
CRIType-MDA 3501 Bridge Rectifier3A-MDA3501
FLPanel-Mounting Non-Indicating 3AG Cartridge-Iype Fuse Post79-44)1001
FL7 A, 250 V, 3AG Slow-Blow Glass Cartridge“Type Fuse46-2017002
FlLabel for Fuse Value037639-01
F24 A, 250 V, 3AG Slow-Blow Glass CartridgeType Fuse46-2014002
F2-F65-Position 3AG Fuse Block with % -Inch Quick-Disconnect Terminals79-3206
F2-F6Fuse Harness AssemblyA035891-02
F2-F6Fuse Block Cover03454401
F2-F6Label for Fuse Values.037641-01
F3,20 A, 32 V, 3AG Slow-Blow Glass CartridgeType Fuse46-301203
F42-Circuit Single-Row Terminal Block(located under F4)79-15021001
FA-F64 A, 250 V, 3G Slow-Blow Glass Cartridge Type Fuse46-2014002
FLIRFI Filter Assembly(designation not marked)A034630-01
J2Power Harness AssemblyA035890-01
J3Voltage Plug for 120 V (105-135 VAC. Yellow wire color—plugs into J3.)A021084-02
JAAAC Harness AssemblyA034629-01
TlTransformer Assembly(designation covered. Acceptable substitute is part no.A035888-01

‘A035888-02.) Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x *%,-lnch Outside 78-2708 Diameter x %-Inch Thick

Power Supply Chassis Base 034482-02 Meal Base Plate (not shown in illustration) 037243-01

5-33

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 65

Crystal Castles

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE The true state of a signal. For example: The active state for START is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as a 1 or a 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice.

CLOCK A repetitive timing signal for synchronizing system functions.

COINCIDENCE Occurring at the same time.

COIN COUNTER A G-digit electro-mechanical device that counts the coins inserted in the coin mechanism(s).

COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

Glossary

CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electro-magnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and. memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage. GATE

  • A circuit with one output that responds when and only when a certain combination of pulses is present at the inputs.

Gul

Page 66

Glossary

  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used, IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ }s a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention, Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (i or 0) value at the node of a logic element or integrated circuit during a particular time. Also cailed the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are Called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER 1, A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR, A device designed to have a definite amount of resistance. Used in circuits to jimit current flow or to provide a voltage drop. ROM Read-only memory, A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y¥ coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruc: tion if a program malfunction occurs. If Crystal Castles

a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting, X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 67

Crystal Castles Ist Printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fil in if you wish a reply

Name

Firm O Distributor

Address C1 Operator City State Zip Other __. __

Area Code Phone

Page 68

First Fold

No postage necessary if mailed in the United States

Sunnyvale, California 94086 be

USINESS REPLY MAIL a

PERMIT NO. 1004 SUNNYVALE, CA ns POSTAGE WILL BE PAID BY ADDRESSEE De | Atari, Inc. be | Attn.: Field Service/Coin-Op Division Ee P.O, Box 427 Pt ns a

wold

28pa spp adez

Page 69

Crystal Castles 1st Printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm CO Distributor

Address _, © Operator

City Country O Other es

Phone: Country Code ______ Local Number

Page 70

First Fold

No postage necessary if mailed in the United States

Sunnyvale, California 94086 be

USINESS REPLY MAIL a

PERMIT NO. 1004 SUNNYVALE, CA ns POSTAGE WILL BE PAID BY ADDRESSEE De | Atari, Inc. be | Attn.: Field Service/Coin-Op Division Ee P.O, Box 427 Pt ns a

wold

28pa spp adez

Page 71

ES BER ER BUR ER DUR BES SEES 2

:

2° ° ;

Warranty

Selier warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective; (b)Such products are returned prepaid to Seller's plant; and
  • Seller’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper, repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

© SS LS SS SS The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. © © s © © ©

IN s

Page 72

A

ATARI

ATARI, INC. 790 SYCAMORE DRIVE PO. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488

4 Warmer Communications Company