CATHODE RAY TOMES

Invasion The Abductors (44068-101 Oct 1999)

Invasion: The Abductors (version 5.0) (Midway, 1999) · Manual · 72 pages · 48 sections · original scan

Page 1

OCTOBER 1999 16-44068-101

2-PLAYER 25” VIDEO GAME

~ MACHINE

CONVERSION KIT

Manual Includes

e Installation & Parts e Operation « Wiring Diagrams Menu System e Testing & Problem Diagnosis e

  • Midway Games Inc. 3401 N. California Ave. Chicago, Illinois 60618-5899 USA Visit our Web site at http:/Awww.midway.com
Page 2

~ INVASION’ kit

INSTALLATION AND PARTS

WARNING Use of non-Midway Games, Inc. parts or circuit modifications could cause serious injury or equipment damage! Use only Midway-authorized parts. For safety and reliability, do not substitute parts or modify Midway products. Substitute parts or modifications may void EMC directive or FCC type acceptance. Read all warnings and instructions before attempting conversion.
Page 3

SAFETY INSTRUCTIONS

The following safety instructions apply to operators and service personnel. Read all instructions before preparing your Video Game Machine (VGM) for play. Other safety instructions appear throughout this manual.

DEFINITIONS OF SAFETY TERMS

DANGER indicates an imminent hazard. Failing to avoid this hazard WILL cause death or serious injury.
WARNING indicates a potential hazard. Failing to avoid this hazard COULD cause death or serious injury.
CAUTION indicates a potential hazard. Failing to avoid this hazard MAY cause minor or moderate injury.
CAUTION also alerts you about unsafe practices.

NOTICE indicates information of special importance. Observing notices may prevent you from damaging the VGM equipment.

Installation - 2 NOTICE: CONVERSION CABINETS. While you can install this kit into many cabinets, Midway Games, Inc. recommends you convert a shooting-style VGM. The similarity of the control panel and internal construction will make it easier. This manual details how to convert a typical VGM, but your circumstances may biota further modifications. Midway. accep

WARNING: DISCONNECT POWER. Always turn the AC power off and unplug the line cord before attempting service or adjustments. Installing or repairing board assemblies while the power is on can cause injury, damage components, and void the warranty.
WARNING: GROUND VGMs. Avoid electrical shock! Do not plug a line cord in until you have inspected and properly grounded the VGM. Only use a grounded, three-wire outlet. Do not use a “cheater” plug, or cut off the ground pin on the line cord, Be certain that ou have reinstalled any internal ground wires removed during .
WARNING: INSPECT SALVAGED PARTS. Kit completion requires reusing parts from an existing VGM. Salvaged parts must operate perfectly. Otherwise, the converted VGM will not perform properly or safely. Before you attempt conversion, repair board assembly malfunctions and cabinet damage.
WARNING: HAZARD TO EPILEPTICS. A very small portion of the population has a condition which may cause epileptic seizures or momentary loss of consciousness when viewing certain kinds of flashing lights or patterns that are present in our daily environment. These persons may experience seizures while watching some kinds of television pictures or playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition. \f you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), immediately consult your physician before using any video games. We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, discontinue use immediately and consult your physician. This waming label is in your kit and must be posted on game's bezel if not already present.

Midway Games, Inc.

Page 4
CAUTION: HANDLE ELECTRONIC DEVICES WITH CARE. The electronic components in this kit are sensitive to static electricity. Before handling electronics, observe the following precautions. ¢ Before handling electronics, discharge static electricity on your body. Touch the safety ground stud on the power chassis or the power supply case before touching electronics. Store electronic assemblies in an anti-static area. Use an anti-static bag to store the CPU Board Assembly. After you install the new unit, reuse the same bag to protect the existing CPU Board Assembly. Do not remove or connect electronics when cabinet power is on. Otherwise, you will damage the electronics and void your warranty.
CAUTION: USE PROPER FUSE. Avoid electrical shock! Replacement fuses must be of the same type as the originals. Fuse voltage and current ratings on the replacement fuse must match voltage and current ratings on the original fuse.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. A dropped fluorescent tube or CRT will break and explode, sending shattered glass flying eight feet or more. Do not drop them.
CAUTION: CHECK WIRING. This kit uses much of the existing VGM's wiring, including your JAMMA harness. Avoid improper operation! Check the wiring after you complete the conversion but before tuming on the power. Verify that the wiring matches the diagrams in the Wiring Chapter.

NOTICE: INSPECT POWER SUPPLY. Be sure your existing power supply can produce these voltages and currents: +5VDC at 6A, -SVDC at 1A and +12VDC at 2A. Measure these operating voltages before disconnecting the existing electronics. Power supply voltages must measure within +/-5% under load. Your power supply must be approved for radio frequency interference and product safety.

NOTICE: CHECK MONITOR TYPE. This kit is not compatible with X-Y monitors. Suitable monitors have horizontally mounted CRTs and raster electronics. Only use a monitor with inputs for RGB video and composite or negative sync.

NOTICE: SERVICE COIN MECHANISMS. Clean your existing VGM's coin mechanisms and test them with appropriate currency. Servicing these mechanisms is crucial to your VGM's earning potential. For your convenience, the factory provides meter wiring information. Currency acceptors and coin meters are not included in the kit.

Invasion® Conversion Kit Installation - 3

Page 5

PRODUCT SPECIFICATIONS Equipment Characteristics

Video Display MonitorAudio SystemCui
Low (standard) resolution, RGBMono sound for4 mechanical coin switch inputs,
with composite, negative sync4 ohm or greater loadDollar bill validator input,

1 audio channel Electronic coin acceptor input Game Characteristics

Player Variables Qperator Variables Diagnostics

1 or 2 players per game,Coinage, Game options,Automatic power-up self-test,
High score recognitionDifficulty, Volume,Manual multi-level menu system

Audits, Statistics

INSPECT THE KIT Unpack the materials from the carton and check for obvious signs of damage. Use this checklist to ensure the kit is complete. You must supply the remainder of the materials required for this conversion. Before attempting any step in this manual, read through the procedure to make sure you understand it. Also ensure that the components and tools for the procedure are handy before attempting the procedure.

A |) ARTWORK AND DOCUMENTS CO Marquee decal 13182 [1 || O1-1/4inch 10-24 cartage bot [A10-01129-208] 6 | T Bezel nstructions decal [+ |[SKepsnuttoze _—ifaato-orze-00 [ez

T Gabinet side panel decal[WGunassemby, mountand cable _Joatizas[2 |

{Manual Invasion conversion kt [16-440 [+ | [Flat washer 203 x.466 x 030 inch [4700-00129-00_|T2| A Q Gun mount template Q Holster mount template Q VGM registration card

| OCopyright 1998 labelfte-toseg| [OKepsnut(44 T0-01128-00 [85]

[GBI waming obs ——fressaraas—[r]{——___y tJ [ETEpiepsy warning abel ]re-aoaa1 [7 LL 0 Torrtong arm ey ase [eases Tr Toc tong ry O Gun PCB cable (2 | Teround wie [Spacer POE mig a” ose [6 | Net aaa ec hex washer head [STiavasion CPU Board Assembly —[aaa5a7 [7] PO

| 2Gun interface Board Assembly [04-11315.2 | 1 | Q 5/8 inch spacer PCB mig, #8 o3-8338-5 | 2 | Q 1-1/4 inch sheet metal screw #6 4106-01115-20 plain hex washer head

Installation - 4 Midway Games, Inc.

Page 6

YOU WILL NEED THESE TOOLS AND SUPPLIES:

QBlack, semi-gloss paintQ = Center punchQ_Nut drivers or socket wrench set
Q_Electric drill and wood bitset©180 gritsandpaperorpowersanderSafety utility knife
QQScrewdriversQ == Quick-hardening wood puttyQSqueegee or soft sponge
QLiquid soap (dish detergent)0Electrical tape or heat shrink tubing© QHole saw or equivalent
QGrease pencil or markerQ > Small screw assortmentQContinuity tester (V.O.M. or

equivalent) CABINET MODIFICATIONS

1.

4.

10,

11.

12. Verify operation of the existing VGM before making changes to the cabinet. Pay special attention to components you will reuse, such as power supply, video monitor, currency acceptors, JAMMA harness, cabinet locks, marquee fluorescent light, speaker(s), etc.

Switch AC power OFF. Disconnect line cord from AC power.

Clear work area. Cover or protect non-wood items, such as marquee, monitor, coin door, brackets, line cord, ete.

STRAIGHTEN TEMPLATE Locate gun and holster mount template. Stack large, heavy items like newspapers, books, or magazines on the template so it will be flat when you are ready to use it.

PREPARING TEMPLATE PRIOR TO USE

SIDE PANELS Remove existing decals and artwork from the cabinet sides. Clean off glue residue. Fill gouges, unused holes, ete. with quick-hardening wood putty. Sand smooth and remove dust.

PAINT Cover both side panels evenly with black paint. Allow paint to dry completely.

DECALS Hold left side panel decal in position and mark a line at the top. Remove decal.

Lightly moisten panel with soapy water. Remove decal backing and apply decal. Start at top, using pencil line as a guide.

Moving outward from center of decal, smooth it down with a squeegee or sponge. Squeeze out any air bubbles. Pop stubborn bubbles with utility knife and smooth down.

Repeat previous step for right side panel. Allow at least 12 hours for adhesive in decals to set.

MARQUEE HARDWARE Remove viewing glass or marquee glass and set in safe place. Remove existing backlit marquee artwork at cabinet top.

MARQUEE ILLUMINATION Clean inside of the marquee. Inspect lamp assembly. If you find cracks or darkened ends in the original fluorescent lamp tube, install a new one.

Invasion® Conversion Kit Installation - 5

Page 7
  • MARQUEE ARTWORK Use previous marquee artwork as a guide to trim kit artwork to size.

14, Clean new marquee artwork and install on VGM. Reinstall marquee glass

  • MONITOR BEZEL. Clean existing monitor bezel. Remove labels that cannot be covered.
  • BEZEL DECALS Apply player instructions decal to bottom of the bezel. Apply epilepsy warming label on top of monitor bezel. Do not let decals or labels obstruct viewing area.

16-9922.1 EPILEPSY WARNING 31-3186-2 MARQUEE DECAL

31-3188.1

LOCATION OF DECALS AND LABELS

  • VIEWING GLASS Clean CRT face and viewing glass and replace them.
  • REAR DOOR Remove and save screws at top and sides of rear door. Unlock rear door, lift from cabinet, and set aside.

19, CLEAN INTERIOR Cover existing electronics with plastic sheet for protection. Vacuum dirt or debris from inside cabinet. Be careful to keep vacuum cleaner motor away from electronics and monitor.

  • CONTROL PANEL Unscrew and remove speaker grill(s) from control panel. Unscrew speaker(s) and gently place inside cabinet. If you must disconnect speaker harness(es), mark wire polarity and functions. Incorrectly phased speakers can cause weak, low frequencies or thin, hollow sound quality.

21, Remove controls and decals from control panel. Disconnect START button switches from main harness and mark function of each wire for later use.

22, PLAYER CONTROLS This kit requires two START buttons. Note button locations on drawing below. Fill extra holes with suitable material, like quick-hardening wood putty. Sand smooth. Remove dust.

  • ARTWORK Peel off backing from wallpaper decal and place it over the control panel board, smoothing from the center out with a squeegee or sponge. Trim edges to fit.

Je START BUTTONS —. On

SPEAKER: SPEAKER GRILLE

TYPICAL CONTROL LOCATIONS

Installation - 6 Midway Games, Inc.

Page 8
  • CABINET FRONT Disconnect existing gun cables from the main hamess. Unscrew gun mounts, and remove guns and gun cables. If you wish to replace your holsters, remove existing holsters, screws, or other items from the front of the cabinet.
  • Compare the previous gun mount hole pattern with the pattem on the kit template. If the existing pattern of four holes matches the template pattern, do not fill the existing holes. Fill all other holes with putty. Sand smooth and remove dust.

INSTALL GUN HOLSTERS

  • HOLE LOCATIONS Identify the right gun holster portion of the template. Position the right holster template on the contro! pane! so there will be clearance from the speaker(s) and buttons. Tape the template in place.
  • Verify that when you drill holes you will not encounter any internal bracing, wires or cables, or other interference. When you are certain the screws will be able to penetrate the panel without resistance, center punch the hole locations.
  • Repeat the previous step for the left gun holster hole locations and remove the template.
  • Cut or drill all the holes. Deburr the holes.
  • HOLSTER BRACKETS Remove speaker or lift control panel to access bottom of panel. Line up three bolts and insert right holster into contro! panel. Fasten nuts over bolts inside control panel and tighten.
  • Repeat previous step for left gun holster.
  • To remove rubber tube for replacement, cut rubber off metal tube. Grasp metal tube with pliers and remove screws. Place new rubber tube over metal tube and hold in position in holster. Insert both screws and hand tighten. Using two screwdrivers, tighten both screws at once.

AMEE aes NO 178398-001 iad x HOLSTER BRACKET

IS ER BRACKE

RUBBER TUBING: \f

METAL SPACER

4410-01128-00 KEPS NUT 10-24

TYPICAL HOLSTER INSTALLATION

Invasion® Conversion Kit Installation - 7

Page 9

INSTALL GUNS

  • GUNS Insert one gun (both guns are identical) into each holster. Straighten the armored gun cables and let them hang freely.
  • If the four holes needed are missing, locate a position for them. Position the gun mount portion of the template beneath the control panel. Locate the mount so players can move the gun freely. Align the two top holes of the triangular template parallel to the ground. Tape the template into position.
  • Verify that when you drill holes you will not encounter any internal bracing, wires or cables, or other interference. When you are certain the bolts will be able to penetrate the pane! without resistance, center punch the hole locations.

11, Repeat the previous two steps for the left gun mount and remove the template.

  • Cut or drill all the holes with a hole saw and deburr them.
  • Insert the left gun cable connector and grounding wire through the large central gun mount hole on the left side of the front panel. Align the gun plate with the three holes. install three 10-32 by 1-1/4” carriage bolts through the gun plate into the mounting holes. Press the bolts to seat them fully.

4410-01129-00 KEPS NUT 10-24 178398-001

04-11243 OPTIC GUN

~..___ 4700-00129-00 FLAT WASHER 04-12460 GUN PLATE a as 0-01136-20B BOLI 10-32x1 1/4"

TYPICAL GUN MOUNT INSTALLATION

  • GROUNDING RING Place the ring terminal of the cable over any one of the carriage bolts.
  • Install a flat washer and KEPS nut on each bolt on the inside of the panel. Tighten the bolts securely.
  • Repeat the previous three steps for the right side. Check that gun cables move freely in all directions.
  • Inside the cabinet, mate the left gun assembly connector to a gun-to-main-harness cable. Route the cables away from the other cabinet wiring.
  • Repeat the previous step for the right gun.

oo Installation - 8 Midway Games, Inc.

Page 10

COMPLETE CONTROL PANEL

1. Peel off backing from add-on decals and place them on the control panel where the START buttons will go. Be sure that the blue start decal is on the left and the red on the right.

Locate and drill holes through the wallpaper and control panel wood for the start button and speaker(s), if not already present. If the holes are already there, use a utility knife to cut through the wallpaper where the speaker and START button holes are. Deburr the holes.

BUTTONS Separate microswitches from pushbutton housings.

Place the transparent control panel cover over the wallpaper. Use the utility knife to cut out the shape of the speaker(s). Use the hole saw to drill holes for the start buttons.

Insert blue button into left start hole and hand-tighten nut. Attach switch to blue button.

Insert red button into right start hole and hand-tighten nut. Attach switch to red button.

Attach a button assembly switch to the main harness connectors under the left button hole. Refer to the labels you previously placed on the connectors. Repeat for right button hole.

Replace speaker(s) and tighten screws snugly. Replace speaker grill(s). Do not overtighten screws.

TYPICAL COMPLETED CONTROL PANEL AND CABINET

Invasion® Conversion Kit Installation - 9

Page 11

INSTALL ELECTRONICS COMPONENTS

NOTICE: DIAGNOSTIC SWITCHES Some early video game machines did not tequire external switches. If your cabinet does not already have TEST, VOLUME, and CREDIT switches installed, you should do this before completing the conversion. Tests and adjustments may be very difficult without these switches.

CAUTION Game electronic components are static sensitive. Prepare an anti-static work area. Ground yourself before removing the CPU Board Assembly from its protective shipping materials.
WARNING Do not connect cables to the CPU Board Assembly or power supply while the power is on. Doing so can cause injury, damage game electronics, and void your warranty.
CAUTION: ATTACH CONNECTORS PROPERLY. Be sure that board assembly connectors mate properly. If connectors do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Connector keys allow a connector to fit only one set of pins on a board.
CAUTION: DO NOT OVERTIGHTEN SCREWS. Overtightening screws through circuit boards can damage the board. Tighten the screws firmly, but not so tight that they cause the board to warp or crack. Circuit board damage can void the warrantee.
CAUTION: SEAT CONNECTORS GENTLY BUT FIRMLY. Connectors are keyed and should fit snugly onto board assemblies. Never force a connector, as you may damage the wires on the board.

NOTICE: RADIO FREQUENCY INTERFERENCE. A ferrite bead, or other radio frequency interference suppression device, may be required to help your VGM mode! comply with EMI requirements.

  • MOTHERBOARD Disconnect the JAMMA harness from all existing board assemblies. Remove board assemblies, disk drives, drive mounting plates, etc. Store items in anti-static packaging.
  • If the electronics mounting shelf is vertical, remove it from its mount. If no shelf exists, supply one that you can fasten safely into the cabinet. If the shelf is horizontal, proceed to the next step.
  • Place spacers beneath the comer and middle holes of the CPU Board Assembly. Mount the assembly on the shelf in same location as original assembly. Mark and drill pilot holes if necessary. Fasten screws through corer and middle holes of the board, spacers, and shelf, but do not tighten. After each screw is seated, tighten them all.

NOTICE: DRILL HOLES IF NECESSARY. Depending on mounting surface material, you may want to drill pilot holes before you insert the screws. If this is the case, use the board assemblies as templates to mark hole locations with a pencil, then drill the holes before mounting the board assemblies with the screws.

Installation - 10 Midway Games, Inc.

Page 12

7. FERRITE BEAD (REQUIRED FOR ——\_ SOME MODELS) ~~ DIP SWITCHES

LITHIUM BATTERY 3v —

FUSE CONDITION LED SHELF (ON = FUSE OK)

GUN INTERFACE BOARD ASSEMBLY CPU BOARD ASSEMBLY SPACERS. TYPICAL ELECTRONICS TRAY INSTALLATION

|. DAUGHTERBOARD Insert a standoff spacer into a corner hole of the Gun Interface Board Assembly. The spacer should go into the side with the components and snap into the holes.

Turn the board so the spacers are on the bottom. Insert screws down through the spacers from the non-component side of the board.

Connect the Gun Interface Board Assembly to CPU Board Assembly at P3. Press the connector down firmly but do not force.

Fasten the two gun interface board screws into the shelf. The screws will drill their own holes.

If you have a vertical shelf, return it to its position inside the cabinet.

Mate the existing JAMMA harness connectors to the CPU Board Assembly sockets.

q q i SCREW

GUN INTERFACE BOARD ASSEMBLY

J PCB STANDOFF

GUN INTERFACE BOARD AND HARDWARE

Invasion® Conversion Kit Installation - 11

Page 13

LAMP ACCESS PANEL

CAM LOCK

LOUVERED VENT

HANDLE OPTIC GUN

| ——puastic cur

POWER SUPPLY AND MOUNTING BRACKET

LINE CORD

GAME ELECTRONICS

REAR DOOR ASSEMBLY.

REAR VIEW OF TYPICAL COMPLETED CABINET

Installation - 12 Midway Games, Inc.

Page 14

WU WIRE THE CABINET

NOTICE: JAMMA HARNESS REQUIRED. This kit does not include a JAMMA harness, which is required to complete installation.

CAUTION Properly insulate unused wires within the JAMMA harness, especially power wires. (Power wires are red, yellow, orange or black.) Secure unused connectors away from the VGM electronics.

GROUND WIRES Locate the braided ground wires with the kit. Remove a KEPS nut on one of the gun mount bolts inside the cabinet. Repeat for the other gun mount. Attach one end of each ground wire to a bolt and reinstall the nuts. Attach the free ends of the ground wires to the central, common ground point in the cabinet. (Ground wires are usually green, although some may be green with a yellow stripe.) Verify low resistance continuity between the gun mounts and the cabinet's line cord ground pin.

NOTICE Electrical codes require you to ground exposed conductive assemblies for safe product operation. Proper grounding protects both the equipment and the players.

DC POWER Inspect existing cabinet wiring and compare it with.the Typical Cabinet Wiring Diagram. Make all connections necessary. Be especially careful to correctly wire +5, -5 and +12-volt connections.

START Connect JAMMA harness wires to START buttons. Insulate unused control panel wires.

GUNS Mate the remaining connector of the right gun-to-main-harness cable with Gun Interface Board Assembly at (P2).

GUN_ INTERFACE ASSEMBLY BOARD

D RIGHT GUN~TO-MAIN~ HARNESS, "CABLE CONNECTOR

PI LEFT GUN-T0—MAIN-HARNESS———~ CABLE CONNECTOR Z )

GUN-TO-MAIN-HARNESS CABLE CONNECTORS

Mate the remaining connector of the left gun-to-main-harness cable with Gun Interface Board Assembly at (P1). Connect the monitor sync cable to Gun Interface Board sync jack J1. (The sync cable is part of the JAMMA hamess.) Secure cables to the cabinet with your own cable clamps and screws.

Connect JAMMA harness wires to speaker wires. Be certain to observe correct speaker polarity.

Connect ground wires that you loosened or removed earlier (control panel, coin door, etc.).

Place the FB] Warning Label next to the VGM electronics. Be certain the label is completely visible.

Invasion® Conversion Kit Installation - 13

Page 15

POWER UP AND TEST

  • Plug the power cord into the AC line and turn on the power. LEDs on the CPU Board Assembly should illuminate.
  • The game program loads and begins self-diagnostics. If no errors occur, the game automatically enters Attract Mode. If problems occur, note any on screen errors, check wiring, and troubleshoot the machine (see Troubleshooting Chapter).
  • Press and hold the TEST MODE switch button until the Test Menu appears.
  • Select Diagnostic Tests at the Main Menu.

Scroll with vol+ / vol- Select with Any Button

Switch Test Dip-Switch Test System Test Sound Test Monitor Patterns Burn-in Test Coin Counter Test Return To Main Menu

  • Perform each test in the Illustrated Diagnostic Test Menu list above. Tests are explained in the Operations Chapter.
  • When finished with the Coin Counter Test, select Return to Main Menu.
  • Select Exit to Game Over at the Test Menu. The system should enter Attract Mode. Press the SERVICE CREDITS button to allow game play. Choose a gun and press the START button to begin play. Listen to the audio while playing the game. Note sound irregularities (phase problems, no low frequencies, etc.). If you find problems, check the wiring hamess for internal shorts or breaks.
  • Replace the rear cabinet door. Allow the system to operate for several hours before attempting any game changes. Verify that the monitor is adjusted for best video display characteristics.
  • After you confirm proper operation, submit the VGM for FCC or other agency approval.

NOTICE: FCC COMPLIANCE. Installing this kit in an existing VGM does not guarantee compliance with FCC requirements. You are solely responsible for acquiring an FCC compliance label. Remove existing FCC compliance labels and do not install a new label on the converted VGM until you have verified compliance at a certified test facility.

  • Press and hold the TEST MODE button until the Invasion Test Menu appears on the screen.
  • Select Game Violence at the Game Adjustments Menu. Set the game violence level as desired. Return to the Game Adjustments Menu and set the other variables as desired. Exit to Game Over.
  • Shoot aliens. Collect currency or tokens. Enjoy.

Installation - 14 Midway Games, Inc.

Page 16

NOTICE This is not the actual template. If your template is missing or damaged, copy this page and use the copy as a template. Do not remove this page from the manual.

START Button 1.187”

eo ® Bolt Hole .25" Bolt Hole .25”

LEFT HOLSTER/START BUTTON MOUNTING TEMPLATE

<p Bolt Hole .25”

START Button 1.187” Bolt Hole .25” Bolt Hole .25”

RIGHT HOLSTER/START BUTTON MOUNTING TEMPLATE

Invasion® Conversion Kit Installation - 15

Page 17

NOTICE This is not the actual template. If your template is missing or damaged, copy this page and use the copy as a template. Do not remove this page from the manual.

TOP EDGE

Bolt Hole .27” Bolt Hole .27"

Cable Thru Hole 1.75”

Bolt Hole .27°

GUN MOUNTING TEMPLATE (LEFT AND RIGHT)

Installation - 16 Midway Games, Inc.

Page 18

~ INVASION” kir

OPERATION, FEATURES, MAINTENANCE & SERVICING

Page 19

GAME OPERATION STARTING UP Whenever you turn on the machine or restore power, the system executes boot ROM code. The boot ROM contains self-diagnostic tests. These tests automatically verify and report the condition of game hardware. The screen is blank during these tests. If the hardware fails a test, the system displays an error message. The message appears for 30 seconds or until someone presses a button.

¢ If nobody presses a button, the system quickly completes tests, and then loads game software. e To skip boot ROM tests and activate the Menu System, press and hold the TEST MODE button.

Having passed power-up tests, the system enters Attract Mode. Attract Mode consists of typical game scenes and sounds, altemating with high scores. Attract Mode continues until game play commences.

GAME RULES

ONE OR TWO PLAYERS Players insert currency to start the game. Each player chooses a gun and presses the nearest START button. One player selects a theater of war by shooting its name on the screen. (The first to shoot a theater of war selects for both players.) Each character receives a starting health level. The game commences. Indicator bars at the top of the screen graphically compare player scores. New players can join the ongoing competition by inserting currency and pressing START. Play progresses until players exhaust their characters’ health. If players choose not to continue, the system returns to Attract Mode.

PLAYER CONTROLS

¢ START Buttons These buttons allow players to begin or continue play. These same buttons select items from the menu during service.

e GUNS Use a gun (Multi-Mode Plasma Disrupter) to shoot aliens and other enemies. Also use a gun to shoot player health and gun-upgrade symbols. Upgrades include rapid fire, missiles, the death ray, a shield and an extra life.

SIGHT

GRIP GUARD

TRIGGER

METAL CABLE

GUN PARTS

Operation - 2 Midway Games, Inc.

Page 20

OPERATOR CONTROLS

CABINET CONTROLS

¢ The DIP Switches set some system variables. You can set other variables with diagnostic control switches,

e The Monitor Remote Control Board allows you to adjust the video display for optimum viewing.

¢ The POWER Switch tums off the game, but does not reset game variables.

DIAGNOSTIC CONTROL SWITCHES

e The SERVICE CREDITS Button allots credits without changing the game's bookkeeping total. SERVICE CREDITS has no function in the menu system.

« The TEST MODE Button causes the game to enter the menu system. Press the TEST MODE button briefly to run automatic tests. To make game adjustments, press and hold TEST MODE until the Main Menu appears. Within the menu system, TEST MODE assumes another function. There, it selects a menu line item and calls up the item's submenu. The screen displays this submenu.

e¢ VOLUME DOWN and VOLUME UP Buttons set game sound levels. To make minor volume changes, press either button briefly. To make major changes, press and hold a button. In the menu system, VOLUME UP moves the item highlight bar up the menu. VOLUME DOWN moves the item highlight bar downward.

NOTICE: You must adjust Attract Mode volume independently of Game Mode volume. For greater profits, increase volume levels to draw attention to this game.

EQUIVALENT MENU NAVIGATION CONTROLS In most cases, certain player switches can duplicate the functions of the diagnostic buttons. Before player switches assume diagnostic functions, you must enter the Menu System. Press TEST MODE to invoke the Main Menu. You may find menu navigation easier with the player switches. Here are the player switch functions within the Menu System...

‘Player Panel Button [eSea ey runeon eg Equivalent Diagnostic Switch _

PLAYER-1 GUNMove up the menuVOLUME UP

PLAYER-2 GUN: | Move down the menu VOLUME DOWN

‘PLAYER-1 STARTSelect a menu itemTEST MODE
PLAYER-2 STARTSelect a menu itemTEST MODE

Invasion® Conversion Kit Operation - 3

Page 21

GAME FEATURES

Invasion is the quintessential, take-no-prisoners dream of every intergalactic soldier of fortune. Dastardly, insectivoid aliens have once again infested several of your leading Earth cities. Earthlings, according to their custom, offer meteoric mercenaries a generous bounty to rescue the planet. The player, our Pleiades paladin, proudly casts a humble homburg into the ring. At last, fortune has smiled upon planet Earth! Here in our hour of need, is our perfect protector. For who else could avenge our beleaguered urban centers? Who else displays boundless, bare-knuckled bravado? Who else possesses that mighty, silver weapon, the dynamic demon demodulator? No one else but this heroic, humanoid hombre. The theaters of war include Chicago, New York, Los Angeles and the Mother Ship. The game associates an individual difficulty level with each theater. Play begins after a player selects any of the three city theaters. Only after securing all cities can vital, veteran players undertake the macabre Mother Ship mission. Two players can play simultaneously. As play commences, the game assigns each player a set number of lives. A mission's object is to preserve these lives and exterminate aliens or demolish war materiel. While avoiding collateral damage to civilians, players must also rescue civilians from alien tractor beams. Otherwise, aliens heinously hydrogenate the minds of their prisoners of war. After reformulation, the pitiful POW wretches return as ferocious, flesh-eating zombies. Ah, the humanity! These tragic, rabid creatures mindlessly and mercilessly plunder player positions. Only benevolent bullets can offer them surcease. Block by block and sector by sector, players advance through each city. Feelers fly. Pincers percolate. Exoskeletons explode. To secure a sector, players must eliminate a quota of aliens, zombies or equipment. Progress from one sector to the next is automatic. After each mission, players who retain lives select another mission and continue crumbling chitinous creatures. If antagonistic, arthropod attackers succeed in taking a player's last life, a “Continue” message appears. The message invites the player to reenlist by inserting currency. Between sector sorties, game action pauses. The system reports player scores and performance ratings. Asecond player can enlist whenever the game displays a “Join-In” message. At various intervals throughout the game, players can acquire weaponry. Players shoot floating “Power- Up” symbols to obtain rapid-fire or special weapons. During single-fire play, screen messages periodically temind each player to reload the gun. An ammunition display also provides a bar graph of remaining bullets in the player's clip. During rapid-fire play, the game automatically resupplies the player's weapon. Aliens retum players’ fire and attack player positions. An alien hit reduces player health. Play continues until both players exhaust their lives. At the end of the game, high-scoring players can enter their initials. If players don't purchase more credits, the game returns to its Attract Mode. eae EFA0.

DIP SWITCHES

FUSE (UNDERSIDE OF GUN INTERFACE BOARD) LITHIUY BATTERY 3v

GUN INTERFACE BOARD CPu_BOARD ASSEMBLY ASSEMBLY INTERNAL COMPONENTS

Operation - 4 Midway Games, Inc.

Page 22

Cw) MAINTENANCE AND SERVICING

« Guns Dirt or debris on a gun lens can affect accuracy. Apply the cleaner to a clean cloth or cotton swab. Use the swab to wipe the lens clean. Don’t apply cleaner directly into the gun barrel!

Only qualified service personnel should perform maintenance and repairs. The following product guidelines apply to all game operators and service personnel. Notes, cautions and warnings appear throughout this manual where they apply. Read the SAFETY pages thoroughly before beginning service.

e Battery Switch off power to the game. Unlock and remove the rear door. If the electronics assembly has a cover, open it. Note the battery position in the socket. Gently lift the contact arm to release tension. Don't bend the arm. Apply slight finger pressure to pry the cell from its holder. Slide the battery out and remove it from the cabinet. Avoid shorts across terminals or between terminals and ground.

To reinstall the battery, orient it near its holder and slide it in under the contact arm. Don't use force.

CAUTION: If you incorrectly install the battery, it may explode. Replace the battery only with the same type, or an equivalent recommended by the manufacturer. Match original batteries in size, voltage rating, and composition. Dispose of used batteries according to instructions printed on the battery or the manufacturer's packaging.

NOTICE: Avoid an explosion! These batteries are designed for very long life. Don’t ( : attempt to recharge them! Avoid direct shorts across battery terminals, or from Ly terminals to ground. While servicing the game, remove batteries from their holders and store them in a safe place. The battery is on the CPU Board.

¢ CPU Board Switch off power to the game. Open the rear door. If the electronics assembly has a cover, open it. Carefully note the orientation of the JAMMA connector and the other cables. Remove CPU Board mounting screws. Separate the Gun Interface Board from the CPU Board. Lift the CPU Board out of the cabinet and set it in a safe place. Use anti-static packaging from new parts to store boards that you won't reinstall.

¢ Gun Interface Board Switch off power to the game. Unlock and remove the rear cabinet door. If the electronics assembly has a cover, open it. Disconnect the wiring hamess from the Interface Board. Remove the boardmounting screws and washers and retain them. Lift the board out of the cabinet and set it in a safe place. Position the replacement board over the CPU Board, align the holes and install the screws. Reinstall the Interface Board wiring harness.

« Guns Switch off power to the game. Unlock and open the coin door. Disconnect the gun cable from the wiring hamess. Remove the locking nuts. Lift the gun cable mount off the front of the cabinet. Retain carriage bolts and nuts from the mount for reinstallation. Reattach the ground connection. Check that the gun cable rotates freely in its mount. Reinstall carriage bolts. Tighten locking nuts.

To disassemble a gun, lay the gun on a work surface and remove the screws. Separate the gun halves, beginning at the handle. Take care not to dislodge parts. (The trigger is spring loaded.) Clean the lens to remove fingerprints and dust. If you removed shields from the gun, reinstall them. After reinstallation, verify that a good electrical connection exists between the shield and cable ground.

Invasion® Conversion Kit Operation - 5

Page 23

BACK LIT MARQUEE

MCNITOR

VIEWING GLASS

TART BUTTONS se

1—OPTIC GUN OPTIC GUN

HOLSTER

CONTROL PANEL DECAL

SPEAKER

COIN DOOR:

CASH DOOR LEG LEVELERS

SCREENED CABINET

TYPICAL EXTERNAL COMPONENTS

CAUTION: Static electricity builds up on your body. This static can damage or destroy sensitive game circuits. BEFORE touching or handling electronic assemblies, discharge static electricity by touching the power supply chassis.

« Memory: ROMs ROM (Read Only Memory) circuits permanently store your game's-operating instructions. Switch off power to the game. Unlock and remove the rear door. If the electronics assembly has a cover, open it.

Note the ROM chip position. Remove the device with a chip extraction tool. To reinstall a ROM chip, orient the device over its socket. Press the chip firmly to seat pins. Don’t force the chip into the socket.

« Memory: RAMs DIP (Dual Inline Package) circuits contain your game's random-access, or read-write memory. In this game, RAM chips are soldered to the CPU Board. As a result, these RAMs aren't user serviceable.

Operation - 6 Midway Games, Inc.

Page 24

~ INVASION ® kr

DIAGNOSTIC, AUDIT & ADJUSTMENT MENU SYSTEM

NOTICE: This manual is subject to change without notice. Midway Games, Inc. reserves the right to make improvements in equipment function, design, or components as progress in ‘ engineering or manufacturing methods warrant.

Page 25

MENU SYSTEM

WHAT IS THE MENU SYSTEM? The game's Menu System is a series of auditing, game adjustment and diagnostic screens. You can easily access and apply these screens to optimize game performance. For instance...

e Use game audits screens to assess game performance. e Use adjustment screens to help you to customize game performance. For instance, you can restore factory default game settings. You can also calibrate player controls for accuracy. e Use diagnostic screens to verify proper equipment operation.

ACTIVATING THE MENU SYSTEM Open the coin door. Find the TEST MODE switch inside. Press TEST MODE to invoke the Menu System. The game system responds by exiting Game Mode and entering Diagnostic Mode. The system runs a

  • self-test, and then displays the Main Menu. The Main Menu is the opening screen of the Menu ystem.

Game audits, adjustments and diagnostics are line items on the Main Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.

Invasion Test Menu Game Code Version X.X

Scroll with vol+ / vol- Setect with Any Button

Diagnostic Tests Coin Bookkeeping Game Audits

Main Adjustments Game Adjustments Utilities System Info Volume Adjustment Exit to Game Over

MAIN TEST MENU

MENU LAYOUT Menus differ, but related information tends to occupy the same screen locations.

© The block at the top, center of each screen displays the current menu title.

  • Data (menu items, video signals, statistics, reports, etc.) appears in the center of the screen. « Messages (explanations, control functions, revision levels) display at the bottom of the screen.

MENU NAVIGATION CONTROLS Use VOLUME UP and VOLUME DOWN buttons to highlight an item on any menu. (These buttons are inside the coin door.) Alternately, you may highlight an item with the LEFT GUN and RIGHT GUN triggers. You can only select one highlighted item at a time. To select a highlighted item, press either eo Diagnostics - 2 Midway Games, Inc.

Page 26

START button. You can also select with the TEST MODE (rightmost) button inside the coin door. To return the game to play, highlight EXIT TO GAME OVER. Then press either START button.

AUTOMATIC SELF TEST Whenever you switch the game between Play Mode and the menu system, the self-test activates. This routine runs automatically. It can detect faults that cause game or menu system malfunctions. A self-test usually takes less than a minute.

Diagnostic Test Menu

DIAGNOSTIC TESTS Select DIAGNOSTIC TESTS at the Main Menu. Diagnostic tests allow you to verify the condition of the electrical and electronic hardware in the game.

Highlight a test with the middle two contro! buttons inside the coin door. Select the option with either START button.

Diagnostic Test Menu

Scroll with vol+/ vol- Setect with Any Button

Switch Test

Dip-Switch Test System Test Sound Test

Monitor Patterns

Burn-in Test

Coin Counter Test

Return To Main Menu

DIAGNOSTIC TEST MENU

JO rest vexuue vous seaver O| SS UE SRY SRE Oo Oo ol | al

CONTROL SWITCHES

con verter Pa 9 mews.

TYPICAL DIAGNOSTIC SWITCHES

Invasion® Conversion Kit Diagnostics - 3

Page 27

Diagnostic Test Menu (continued)

SWITCH TEST

Select SWITCH TEST at the Diagnostic Test Menu. The Switch Test Menu opens. This menu verifies proper operation of the game's switches, including buttons and gun switches.

Activate each switch, and the indicator on the screen changes state. Release the switch and the indicator returns to its previous, normally open or closed condition. You can test any combination of switches. To exit the test, simultaneously press both START buttons.

© start © Start2

O Gun1 O Gun2

©coin1© coinz©) conscons
O vi+Ova-©BisO poor
© creatOC©Senco

SWITCH TEST SCREEN

Switch Indications. Switches appear on the screen as hollow, blue circles. A circle with a black center indicates an open switch. A circle with a yellow center indicates a closed switch. Any other center color indicates a fault. Whenever you toggle a button or pull a gun trigger, a circle should change color.

Use the Switch Test to locate crossed wires, improper cabling, intermittent conditions and stuck switches.

NOTICE: This game may not use some switches. If you can't find one of the listed switches, check the wiring diagram.

Diagnostics - 4 Midway Games, Inc. om

Page 28

Ne) Main Menu (continued)

Diagnostic Test Menu (continued) DIP Switch Test Menu

DIP SWITCH TEST

Select DIP SWITCH TEST at the Diagnostic Test Menu. Two 8-position DIP switch banks reside on the CPU Board. The DIP Switch Test Menu reports the positions of 16 switches in these banks.

Highlight a test with the middle two control buttons inside the coin door. Select the option with either START button. The screen displays an illustration of each switch block and the current settings.

You can change DIP switch positions with power on. Set any switch. Then check the screen to verify that the new setting is enabled. Turning on the COINAGE CONTROL disables country switch settings.

Refer to the DIP Switch Tables for assistance in choosing switch positions (* indicates factory defaults). To exit the DIP Switch Test, press any game button.

FERRITE BEAD 11/4" S

DIP SWITCHES

LITHIUM BATTERY 3V

D.C. FUSE (UNDER GUN INTERFACE BOARD)

FUSE CONDITION LED WOOD PANEL ore: os

CPU BOARD \_ oun INTERFACE BOARD ASSEMBLY ASSEMBLY

‘ CPU BOARD, SHOWING DIP SWITCH LOCATION

| Invasion® Conversion Kit Diagnostics - 5

Page 29

DIP SWITCH TABLES Pa ad al a ld ld a Fine Inverted Displ (for mirror viewing

Don't Show Blood

Not Used

Not Used

Not Used

Not Used

Not Used

Not Used

CMOS Pricing Selector

USA1GertFrECA1UK1
USA2Ger2FrECA2UK2
USA3Ger3FrECA3UK3
USA4Ger4FrECA4UK4
USASGer5FrECASUKS5
USA9Ger9FrECA9UK9

USA10/Ger10/Fr ECA10/UK ECA USA ECA / Ger ECA/ Fr ECA8

Country Selector USA France Germany United King Not Used Not Used Operating Mode Game Mode Test Mode The screen doesn't flip until you reenter Game Mode. ?Except Free Play, which is “on” for SW2 through SW6.

Diagnostics - 6 Midway Games, Inc.

Page 30

LA Main Menu (continued) Diagnostic Test Menu (continued [—__SystemTestMenuOSOSOSOCCCCCCCCCSY te

SYSTEM TEST Select SYSTEM TEST at the Diagnostic Test Menu. The System Test Menu opens. This menu verifies that crucial system components operate properly. These components include the controller (PIC), clock, RAM and ROM memory chips, microprocessor, etc.

Highlight a test with the middle two control buttons inside the coin door. Select the option with either START button.

System Test (Hold any button to skip) 00:00:00 AM Day-name Month-name DD YYYY

Pic H PIC NV RAM OK

ClockoK[STTIL
Wave RAM Bank 1OKa

Wave RAM Bank 0 oK 2

Fast RAM4oO
Game ROMsOKOo

CMOS Memory ox fog 5

Display INT at

ZEUS ChipOKogooo9o0

Sound System OK

Hit Any Button to Continue

SYSTEM TEST MENU

The System Test incorporates several diagnostic routines. These routines analyze the digital system circuits, and can detect system memory problems. Test results appear on the screen as messages. Reports other than OK indicate a problem.

Invasion® Conversion Kit Diagnostics - 7

Page 31

Main Menu (continued) Diagnostic Test Menu (continued)

SOUND TEST Select SOUND TEST at the Diagnostic Test Menu. The Sound Test Menu appears. This menu helps you to verify that audio components are connected and operate properly.

Highlight a test with the middle two control buttons inside the coin door. Select the option with either START button.

NOTICE: To provide a realistic challenge to the sound system, increase the volume level. Check the volume setting before testing. Before returning to Game-Over Mode, reset the volume level to its original setting.

Sound Test Menu

Sound System Test Play Sounds Return to Diags Menu

SOUND TEST MENU

Sound DSP Test

Sound system status: OK Play Sounds

Select sounds with vol+ / vol- Hit Buttons to Repeat Hit Start Button to Exit

explosion 1 Hit Any Button to Continue

SOUND DSP TEST SCREEN PLAY SOUNDS SCREEN

Play Sounds allows you to recall and play Sound DSP runs a diagnostic routine. This certain game sounds from read-only memory. routine analyzes the digital signal processor Distorted, duplicate, mislabeled or missing circuit. Reports other than SOUND SYSTEM: sounds indicate a problem. (On this menu, you OK indicate a problem. can't use the guns to select sounds. Only the volume buttons serve that purpose.)

Diagnostics - 8 Midway Games, Inc.

Page 32

[Main Menu (continued) Diagnostic Test Menu (continued; Monitor Test Patterns Menu

MONITOR TEST PATTERNS Select MONITOR PATTERNS at the Diagnostic Test Menu. The Monitor Test Patterns Menu opens. This menu provides screens that help you to verify or adjust monitor performance.

Highlight a test with the middle two control buttons inside the coin door. Select the option with either START button.

Monitor Test Patterns Menu

Scroll with vol +/ vol- Select with Any Button

Red Screen Green Screen Blue Screen Color Bars Gray Scale Sizing Pattern Return to Diags Menu

MONITOR PATTERNS MENU

Red, Green and Blue Screens fill the screen with the chosen color at normal intensity. These screens help you to adjust monitor intensity, black level, blanking and color purity. Color should remain uniform from one edge of the screen to the other. No retrace lines or color contamination (streaks of the wrong color) should appear. Defective monitor degaussing circuitry will contaminate one or more color screens.

Color Bars paints colored stripes down the screen. Use the color bars to help you to check or adjust monitor brightness and contrast. The color bars also expose defects in horizontal linearity. Each color bar consists of 16 intensity levels. On a properly adjusted monitor, the top 15 of these levels are visible. Each bar should appear sharp, clear, and distinct from bars on either side. Incorrect adjustment can cause missing detail at the top or bottom of a bar. Bent bars indicate horizontal linearity flaws, such as pie crust, pincushion or barre! distortion. (Correct color bar colors, left to right: Red, Green, Blue, Black, White, Cyan, Yellow, Violet.) Set controls as follows: 1. Adjust BRIGHTNESS and CONTRAST to minimum. 2. Tur up BRIGHTNESS until the pixels in the black stripe begin to glow (turn dark gray). 3. Bring up the CONTRAST control until you can see 15 bars.

Gray Scale creates a monochrome, middle-gray screen. This screen helps you to check or adjust monitor convergence, purity, contrast and intensity. This screen also simplifies black level and color gun contro! settings. The screen should be uniform, with no color tints, distortion, retrace lines or noise.

Sizing (Crosshatch) Pattern fills the screen with a grid and a series of dots. Crosshatch Patterns help you to check or adjust several monitor parameters: These include convergence, linearity, active viewing area and dynamic focus. The grid and the dots should be all white in color, with no fringes or parallel images. The lines should be straight and the dots round. For more detail on these adjustments, consult service literature from the monitor manufacturer.

If tests indicate a need for adjustment, use controls on the Monitor Remote Adjustment Board.

Invasion® Conversion Kit Diagnostics - 9

Page 33

Main Menu (continued) Diagnostic Test Menu (continued, Burn-in Test Menu

BURN-IN TEST Select BURN-IN TEST at the Diagnostic Test Menu. The Burn-In Test Menu appears. Meanwhile, the system performs a semi-automatic test routine. Use this test to locate the cause of intermittent failures in these parts...

Programmable Intelligent Controller chip (PIC) RAM chips Clock chip Battery-backed CMOS RAM chips Display interface Zeus microprocessor

When the test detects a CPU Board error, the test displays an error message.

Use the Burn-In Test to reproduce intermittent faults or infrequent failure modes. After the malfunction occurs, you can locate the cause of the problem troubleshoot the game.

Burn In Test (Press and hold any button to exit) Total Cycles Completed:

= Description PIC PIC N/V RAM Clock Fast RAM CMOS Memory Display INT ZEUS Wave RAM 0 Wave RAM 1 cette iw ecccccese |

BURN-IN TEST MENU

Highlight a test with the middle two contro! buttons inside the coin door. Select the option with either START button. The test you've selected becomes the first test of an automatic cycle. The cycle can detect faults that cause game or menu system malfunctions. One cycle through all the tests usually takes less than a minute. Messages appear on the screen as each item runs. These messages may describe errors. Write down messages before proceeding to the menus or game play.

To abort the test cycle and exit to the Main Menu, press either START button.

Diagnostics - 10 Midway Games, Inc.

Page 34

Uy Main Menu (continuec Diagnostic Test Menu (continued Mechanical Coin Counter Test Menu

MECHANICAL COIN COUNTER TEST Select COIN COUNTER TEST at the Diagnostic Test Menu. The Mechanical Coin Counter Test Menu appears. The Mechanical Coin Counter Test is a manual test. Use this test to locate jammed, burned-out or malfunctioning meters.

Open the coin and cash box doors. Highlight a meter designation. (METER 1, METER 2, etc.) Use the middle two control buttons inside the coin door. Watch the meter, which is inside the cash box door. Press either START button. A good meter will increment once for each time that you press START.

Mechanical Coin Counter Test

Use vol +/ vol- to select meter.

Press any button to click selected meter. Hit START to exit.

\ ) METER 1 METER 2 METER 3 METER 4

MECHANICAL COIN COUNTER MENU

Invasion® Conversion Kit Diagnostics - 11

Page 35

Main Menu (continued) Coin Bookkeeping Menu

COIN BOOKKEEPING Select COIN BOOKKEEPING at the Main Menu. The Coin Bookkeeping Menu permits you to assess the currency collection. The report screen presents revenue quantities and other important game statistics.

Highlight a line item with the middle two control buttons inside the coin door. Select the option with either START button. A menu screen appears as below.

COIN BOOKKEEPING

Left Slot Coins

Right Slot Coins Center Slot Coins

Fourth Slot Coins

Bill Validator Count

Paid Credits

Service Credits

Total Plays Total Collection

Hit Any Button to Continue

COIN BOOKKEEPING MENU

The Coin Bookkeeping Menu reports total quantities of coins, bills or credits collected by each active device. The menu doesn't calculate the value of the collected currency.

This screen reports information, but doesn’t permit you to make changes. To reset the coin, bill, and credit counters to zero, use the Clear Audits menu.

Examine and record audit information before you make changes. Once you've cleared the counters, you can't retrieve the previous data from the system.

Diagnostics - 12 Midway Games, Inc.

Page 36

U -Main Menu (continued) Game Audits Menu

GAME AUDITS Select GAME AUDITS at the Main Menu. The Game Audits menus permit you to review game play Statistics. Additional menus give detailed reports for each player position on game starts, ends, cabinet abuse, fault conditions, etc.

Highlight a line item with the middle two control buttons inside the coin door. Select the option with either START button. The screen displays a list of the statistics available to you. Select an item to view the detailed report.

Audits Menu

‘Scroll with vol+ / vol- Select with Any Button

View Game Audits Return To Main Menu

AUDITS MENU (SCREEN 1)

Data in the Audits menus helps you to keep records of the game's popularity and earning potential. Each Audits Menu entry is the subject for one or more screens of bookkeeping information. Use the highlight bar to select the desired subject.

Examine and record all audit values before performing game service or repairs.

NOTICE: Be careful when clearing audit information. Once you clear data, you cannot restore it.

Invasion® Conversion Kit Diagnostics - 13

Page 37

Main Menu (continued Game Audits Menu (continued) [Audits,Screen20 Audits, Screen 2

UP TIME H: Mi: S NUMBER OF GAMES TOTAL STARTS (ALL BUY-INS) TOTAL CREDITS TOTAL PLAY TIME H: M: S: AVG PLAY TIME H: M: S: AVG CONTINUES PER GAME AVG TIME PER CREDIT H: M: S: AVG CREDITS PER GAME ONE PLAYER TIME H: M: S: TWO PLAYER TIME H:

Next Page

Return to Menu

AUDITS MENU (SCREEN 2)

UPTIME H: M: S. Total on time, measured in hours, minutes and seconds.

NUMBER OF GAMES. Number of games that players played on this Video Game Machine (VGM).

TOTAL STARTS (ALL BUY-INS). Number of games initiated by inserting currency into the VGM. (Sum of Player Starts, Player Joins and Player Continues.)

TOTAL CREDITS Number of credits that players purchased on this VGM.

TOTAL PLAY TIME H: M: S: Hours, minutes and seconds of play for this VGM.

AVG PLAY TIME H: M: S: Approximately how long one game lasts. (Total Play Time / Total Starts.) Two minutes is typical for a new VGM. If games seem to run too long, adjust difficulty settings to make games shorter. If games don't seem to last long enough, adjust difficulty settings to lengthen games.

AVG CONTINUES PER GAME. Approximately how often players pay to continue a game.

AVG TIME PER CREDIT H: M: S: Approximately how long players play per each credit.

AVG CREDITS PER GAME. Approximate number of credits players buy during the course of a game.

ONE PLAYER TIME H: M: S: Length of all one-player games, measured in hours, minutes and seconds.

TWO PLAYER TIME H: M: S: Length of all two-player games, measured in hours, minutes and seconds.

Diagnostics - 14 Midway Games, Inc.

Page 38

WU Main Menu (continued) [MainMenu (continued) C‘C‘*@* Game Audits Menu (continued) L_Audits,Screen3 0 Audits, Screen 3

PLAYER STARTS PLAYER JOINS PLAYER CONTINUES PLAYER ENDS GAME OVERS GAME WINS TWO COUNT PLAYTIME SECONDS TWO PLAYER SECONDS UP TIME

Next Page Previous Page Return to Menu

AUDITS MENU (SCREEN 3)

PLAYER STARTS. Number of games that players started without anyone else playing.

PLAYER JOINS. Number of games where a second player paid to join in.

PLAYER CONTINUES. Number of games that players paid to continue.

PLAYER ENDS. Number of times that the player lost all his character's lives.

GAME OVERS. Number of games where the player didn’t continue. (The VGM displays GAME OVER).

GAME WINS. Number of games where the player completed all waves, including the Mother Ship Wave.

TWO COUNT. Number of two-player games.

PLAYTIME SECONDS. Total game play time, expressed in seconds.

TWO PLAYER SECONDS. Total two-player play time, expressed in seconds.

UP TIME. Video game machine on time, expressed in seconds.

Invasion® Conversion Kit Diagnostics - 15

Page 39

Main Menu (continued) Game Audits Menu (contini Audits, Screen 4

SYSTEM FLAGS WATCHDOGS VERSION cSUM FACTORY RESET COINS CLEARED CREDITS CLEARED

Previous Page

Return to Menu

AUDITS MENU (SCREEN 4)

SYSTEM FLAGS is a hexadecimal number that counts hardware status messages. System flags include peripheral messages such as whether the bill validator is on or off.

WATCHDOGS. Watchdogs record the number of times that the watchdog circuit reset the game software. Watchdog resets may occur due to VGM (video game machine) hardware problems or corrupted software. External circumstances, such as power line glitches or electromagnetic interference may also cause resets. The watchdog hardware times out and resets the system during any unusually long software loop. If unchecked, such loops tend to freeze game action indefinitely. Of course, the reset terminates the game in play. But the reset also returns the VGM to a playable state. If the Watchdogs indication reveals frequent resets, check the VGM and its power environment.

VERSION. Version number of game software in this video game machine. (BCD format)

CSUM. CMOS RAM checksum in hexadecimal. This number depends on the game version.

FACTORY RESET. Date and time when someone last reset game software to factory defaults.

COINS CLEARED. Date and time when someone last cleared coin totals.

CREDITS CLEARED. Date and time when someone last cleared credit totals.

Diagnostics - 16 Midway Games, Inc.

Page 40

WU Main Menu (continued [MainMenu (continued) COCS™CSOCOC(‘<C Main Adjustments Menu

MAIN ADJUSTMENTS Select MAIN ADJUSTMENTS at the Main Menu. Main Adjustments is a menu of screens that permit you to change game characteristics. Use these screens to optimize game performance and earnings. You'll find more of this type of adjustments on the Game Adjustments Menu.

Highlight a line item with the middle two contro! buttons inside the coin door. Select the option with either

MAIN ADJUSTMENTS MENU

Scroll with vol+ / vol- Select with Any Button

Standard Pricing Custom Pricing START button.

Mechanical Counters Bill Validator Free Play Attract Mode Sounds Gun Flash Brightness Return To Main Menu

MAIN ADJUSTMENTS MENU

Standard Pricing opens a menu that allows you to choose from among numerous standard pricing schemes. None of these schemes require setting DIP switches.

Custom Pricing opens a menu that allows you to devise your pricing schemes. On the menu, you specify “slot units” for each coin mechanism (coinage, such as Lira, Marks, etc.). You must also calculate and enter the number of credits per coin. Custom Pricing schemes don’t require setting DIP switches.

Mechanical Counters allows you to add, remove and test coin and bill mechanisms. You set the number of totalizer clicks for each coin through a chute. The Mechanical Counters Menu displays values for all possible devices. Changes to unused inputs have no effect.

Bill Validator opens a menu that allows you to enable or disable bill validator support.

Free Play allows you to enable or disable free game operation.

Attract Mode Sounds opens a menu that allows you to enable or disable attract mode sounds.

Gun Flash Brightness optimizes gun operation. Adjust brightness so that the guns function, but the screen flash doesn’t irritate players. See the separate discussion on Gun Flash Brightness.

Invasion® Conversion Kit Diagnostics - 17

Page 41

Main Menu (continued) Main Adjustments Menu (continued) [________GunFlashBrightnessMenu_ Gun Flash Brightness Menu

GUN FLASH BRIGHTNESS Select GUN FLASH BRIGHTNESS at the Main Adjustments Menu. Use the Gun Flash Brightness Menu to adjust gun operation. But take care: If you set flash brightness too low, the guns may not operate. If set « too high, gun flash brightness might irritate players or reduce monitor lite. On a video game machine with anew CRT, set flash brightness to 1 NORMAL.

Increase gun flash brightness by repeatedly pressing VOLUME UP. Decrease flash brightness by repeatedly pressing VOLUME DOWN. Save your setting and exit the Gun Flash Brightness screen by pressing any button. Gun Flash Brightness

Adjusts Gun Flash Brightness.

Factory setting Is 1 Normal. Current setting Is 1 Normal.

Peng eye Confirm choice with any button. ~~

GUN FLASH BRIGHTNESS SCREEN

SIGHT

GRIP

METAL CABLE

GUN PARTS

Diagnostics - 18 Midway Games, Inc.

Page 42

YU Main Menu (continued) [ Main Menu (continued) Main Adjustments Menu (continued) Standard Pricing Menu

STANDARD PRICING Select STANDARD PRICING at the Main Adjustments Menu. The Standard Pricing Menu allows you to view current settings or change the cost of games. The system restores factory default pricing if the backup battery fails.

Highlight a line item with the middle two control buttons inside the coin door. Select the option with either START button. You may reset options to factory defaults or change an option after viewing it.

We recommend examining and recording all pricing options before making changes.

Select Standard Pricing Mode Vol+ / vol- selects pricing mode. Hit any button to confirm choice. 1of 85 Pricing Mode: USA1 2 to Start, 2 to Continue 1 CREDIT/1 COIN Coin 1 (Left): Coln 2 (Right): Coin 3 (Center): Coln 4 (Extra): Bill Validator:

STANDARD PRICING MENU

An additional box appears on screen to explain the available functions as you select each item.

Invasion® Conversion Kit Diagnostics - 19

Page 43

STANDARD PRICING TABLE

[COIN2 | COINS | COINS | [25e ig Pees —— peat Somme Gaeorrsicow __f cont [eau [2 | ise, 4g eer

AUSTRALIA2

FRANCE ECA 1 FRANCE ECA 2 FRANCE ECA 3 FRANCE ECA 4 FRANCE ECAS FRANCE ECA6 FRANCE ECA 7 FRANCE ECA 8 FRANCE ECA 9 FRANCE ECA 10 FRANCE ECA 11 FRANCE ECA 12 FRANCE ECA 13 V3X20¢, 2/81.00 5X20¢, 1/51.00

1/2x25¢, 3/81 1/2x25¢, 3/81 3/$1.00, 6/ $2.00 1/2x25¢, 3/81

2/5F rr, SAOFr 2/5Fr, 4NOFr ‘USF, S10Fr VUSFr, 20Fr 205Fr, SIOFr, 11/2 X 10Fr ‘265F r, 4/10Fr, 9/2 X 10Fr ‘WSFr, W/0Fr, 7/2 X 10Fr ‘SFr, 210Fr, 5/2 X 10Fr V3 X 1F tr, 2/6Fr ‘V2 X 1Fr, YSFr V3 X 1F r, 2/6Fr, 6/2 X SFr

  • X 1F r, Y6Fr, 7/2 X SFr ‘25Fr, S/0Fr ‘2/5Fr, 4/10Fr ‘WSF r, V10Fr U5Fr, 2/10Fr ‘2/5Fr, S/OFr, 11/2 X 10Fr 265Fr, 4/40F r, 9/2 X 10F SFr, INOFr, 7/2 X 10Fr VSFr, 2/10F tr, 5/2 X 10Fr 3 X 1Fr, 25Fr ‘V2 X 1Fr, S/5Fr V3 X 1F r, 2/5Fr, SAOFr V2. X 1F t, VSFr, TAOFr ANOFt, 2/20Fr, 4/30Fr

FREE PLAY Se

GERMANY 1 GERMANY 2 GERMANY 3 GERMANY 4 GERMANY 5 GERMANY ECA 1 1/1DM, 6/5DM ‘V1DM, 7/5DM 110M, &/5DM 1/1DM, 5/5DM 110M, 6/50M 110M, 2/2DM, 6/5DM. /10M, 2/20M, 6/S0M 1AM, 2/2DM, 6/5DM ee | Hage

SWITZERLAND 3

(Table continues on next page)

Diagnostics - 20 a a Ea

1SFr 1SFr 1SFr AASFr, 7/5SFr AASFr, B/SSFr

Midway Games, Inc.

Page 44

STANDARD PRICING TABLE, continued

SESRIRSSRR SRR REE Es CRRRIRIRRRR RS

“Main Menu (continued,

Main Adjustments Menu (continued

Custom Pricing Menu

CUSTOM PRICING Select CUSTOM PRICING at the Main Adjustments Menu. The Custom Pricing Menu allows you to select the number of coins or credits required for each game. The system restores factory default pricing if the backup battery fails.

Highlight a line item with the middle two control buttons inside the coin door. Select the option with either START button. As you select each item, the screen displays its definition. You may reset options to factory defaults or change an option after viewing it.

Examine and record pricing options before making changes.

Custom Pricing Settings

Use vol+ / vol- to select item. Hit any button to change selected item. Left Units Right Units. Center Units Extra Units Validator Units Units Per Credit Units Per Bonus Minimum Units Credits To Start Credits To Cont. Maximum Credits Coins Per Bill Show Fractions Return to Menu CUSTOM PRICING MENU Units given for each coin the player puts: In the left chute (default is 1). xX XX xX XX xX xX NONE NO MIN xXx xX xX xX xX < a

Invasion® Conversion Kit Diagnostics - 21

Page 45

BASIC CUSTOM PRICING. Custom pricing creates an imaginary currency exchange. In this currency exchange, the coins of the realm are “units.” Think of units as a type of cyber-currency, useful only within the game software. By inserting coins, you purchase units.

Since units are only negotiable within game software, the system stores your units for you. When the system receives enough units, it buys a game for you. The price of a game is one “credit.” You can think of credits as a second form of cyber-currency.

Even though you've now bought one game, you may not be able to begin playing. In many pricing schemes, you must buy two or more credits to begin play. The idea here is something like a minimum order of goods at a store. That is, the operator can “shrink-wrap” two or more games in a package. You can't play unless you buy the entire package.

1 /26¢ COIN; 1 CREDIT TO START. In a simple, quarter pricing scheme, the player inserts one coin to buy one unit. The system exchanges that unit for one credit. If CREDITS TO START contains the value one, then play commences. A dollar bill buys four units.

Validator UnitsUnits / CreditCredits to StartCoins 7 Bil

a CN CU MO CO

*1/3 X 25¢; 2 CREDITS TO START. Again, assuming quarter slots, here's one way to implement 75¢ pricing... In this scheme, each coin that the player inserts buys one unit. The system exchanges three units for one credit. CREDITS TO START contains the value two. To play, the player must pay for two credits. In this scheme, a dollar buys four units.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill

A SS SO UY SO SO. 2/1 COIN; 6 CREDITS TO START. Now let's consider a more unusual pricing scheme. Here, the player can buy two units with one coin. The system exchanges each of these units for one credit. Notice that CREDITS TO START contains the value six. To play, the player must insert two more coins to pay for six credits. Also notice that if the player pays with a bill, the system throws in an extra unit.

Left Slot UnitsValidator UnitsUnits / CreditCredits to StartCoins / Bill

Le 6 4

The following table clarifies Custom Pricing Menu terms...

SCREEN TERM Slot Units; Validator Units DISCUSSION Cyber-currency. This adjustment assigns a number of “units” to each coin mechanism or bill acceptor. For instance, if a quarter buys 1 unit, then $1 buys 4 units. (See Coins Per Bill.) You insert a coin into a 1-unit coin acceptor. The system, due to its programming, knows that your coin is worth one unit.

[Minimum Unis | Units any us eonmull te ator aris oGemRE

Coins per Bill How many coins one bill is worth.

Diagnostics - 22 Midway Games, Inc.

Page 46

UW ‘Main Menu (continued : : : = =

GAME ADJUSTMENTS Select GAME ADJUSTMENTS at the Main Menu. Screens in the Game Adjustments Menu permit you to alter game characteristics. Use these screens to optimize game performance and eamings. You'll find more of this type of adjustments on the Main Adjustments Menu.

Highlight a line item with the middle two contro! buttons inside the coin door. Select the option with either START button.

GAME ADJUSTMENTS MENU

Scroll with vol+ / vol- Select with Any Button

Game Difficulty Game Minimum Time Game Energy Game Violence

Return To Main Menu

GAME ADJUSTMENTS MENU

Game Difficulty allows you to adjust the challenge that the game presents to players. Consider altering this setting when you move the game to a new location. In the same location, you might add play to the game by periodically upgrading difficulty. That way, experienced players won't become bored.

Game Minimum Time allows you to increase or decrease the minimum amount of play time in a game.

Game Energy opens a menu that allows you increase or decrease the amount of “energy” that each player begins with. “Energy” enables the player to recover from enemy hits and continue playing without inserting coins.

Game Violence opens a menu that allows you to choose the level of gore depicted during game play.

Invasion® Conversion Kit Diagnostics - 23

Page 47

Main Menu (continued; ; [____UtilitiesMenu

UTILITIES Select UTILITIES at the Main Menu. Utilities Menu items allow you restore game operation to original software performance. Of course, game performance also depends on the condition of game hardware.

Highlight a line item with the middle two control buttons inside the coin door. Select the option with either

Utilities Menu START button.

Clear Credits Clear Coin Counters Clear Game Audits Reset High Scores Default Adjustments Factory Settings Set Time & Date Return To Main Menu

UTILITIES MENU

Clear Credits opens a menu that allows you to zero the game's credit data. Examine and record audit information before you make changes.

Clear Coin Counters opens a menu that allows you to zero the game’s coin collection data. Examine and record audit information before you make changes.

Clear Game Audits opens a menu that allows you to zero the game's audit data.

Dump Audits allows you to replace current audit data with previously saved data.

Reset High Scores permits you to delete player names and scores that appear in the Attract Mode. This feature may be useful if players insert inappropriate language into the high score table.

Default Adjustments opens a menu that allows you to reset game adjustments to factory settings.

Factory Settings allows you to reset adjustments and audits to values set by the factory.

Set Time & Date allows you to adjust the game's real-time clock. You may adjust for time zone changes, clock resets, backup battery replacements, etc.

NOTICE: Be careful when clearing audit information. Once you clear data, you can’t restore it.

Diagnostics - 24 Midway Games, Inc.

Page 48

Main Menu (continued): System Information Menu

SYSTEM INFORMATION Select SYSTEM INFO at the Main Menu. The System Information Menu presents hardware and software data for your game. Use these numbers to describe the system during part replacement, service calls, etc.

Highlight a test with the middle two control buttons inside the coin door. Select the option with either START button.

Game Serial Number: =Xx00000Kx Game Type: Xxx Date Of Manufacture: Game Code Version: X.X Game Code Compiled: Diagnostic Code Version: X.X Disk Asic U11 Version: Xx System Date: Weekday, Mm, Dd, Yyyy System Time: 00:00:00 Am

Hit Any Button to Continue

SYSTEM INFORMATION MENU

The System Information screen reports information but doesn't permit you to make changes. This screen identifies the game's date of manufacture and the code versions for programmed chips. The Serial Number, Game Type and Compilation Date help to identify the production run.

Invasion® Conversion Kit Diagnostics - 25

Page 49

Main Menu (continued) _ Volume Adjustment Menu

VOLUME ADJUSTMENT | Select VOLUME ADJUSTMENT at the Main Menu. The Volume Adjustments Menu assists you in tailoring sound levels to your environment and your players.

Highlight a test with the middle two contro! buttons inside the coin door. Select the option with either START button. Music plays continuously during volume adjustment. Use the volume buttons on the diagnostic switch bracket to change the sound level of the game.

Volume Adjustments Menu

Minimum Volume Set Game Volume Set Attract Volume Return to Main Menu

VOLUME ADJUSTMENTS MENU

Loud games attract more player interest than games with low-level sound. If your location is noisy, you may want to increase the minimum volume setting.

The Attract Mode sound level is lower than the game play sound level. You can enable or disable Attract Mode sound without changing the game volume level. (See Adjustments.)

NOTICE: These adjustments affect the volume of tests as well as of game play. If you set volume levels to minimum (zero), the speakers are silent during audio tests. We recommend setting volume levels to a moderately high value whenever you perform sound tests. After you complete tests, you may return sound levels to previous settings.

Minimum Volume opens a new menu. This menu allows you to set the quietest game sound. No game sound will be quieter than this setting.

Set Game Volume allows you to set the loudest game sound. No game sound will be louder than this setting.

Set Attract Volume allows you to adjust the volume of the game's Attract Mode. No Attract Mode sound will be louder than this setting.

Diagnostics - 26 Midway Games, Inc.

Page 50

Set Minimum Volume

Sets the minimum level allowed

when setting the volume

Factory setting is 15. Current setting is 30.

Minimum Volume

3%

Select with vol+ / vol- Confirm cholce with any button

MININUM VOLUME MENU

Set Game Volume

Adjust Volume with vol+/ vol-

Hit Any Other Button to Exit

Volume: 30

SET GAME VOLUME MENU

Adjust Volume with vol+ / vol-

Volume: 70

SET ATTRACT VOLUME MENU

Invasion® Conversion Kit Diagnostics - 27

Page 51

NOTES

Diagnostics - 28 Midway Games, Inc. C

Cc)

Page 52

~ INVASION” kn

WIRING

WARNING: Failure to reconnect ground wires or replace metal shields and covers with mounting hardware installed and properly tightened may result in radio frequency interference.
Page 53

JANMA Table CY

[Key TT Key

[NotConnected [--|SICoinCounter1_[ Brown|
[NotGonnected[TKifNotConnected [-

[NotConnected [-- | Mf NotConnected [- |Video Green | Yellow-Green___|_N_ | Video Sync___| Yellow-White | P“fVideo Blue_| Yellow-Blue_[_13_| | Service Credits | White-Gray | R_ [SiamTit_ | Black-Green |S

| Coin2 Input| Black-Red| T—(fCoint input| Black-Brown__ [16

| Player 2Start___| Violet-White | U__—‘fPlayer1 Start [White 17 Not Connected V__|{NotConnected [- 18

Not ConnectediNotConnected [=| 19
Not Connected,[NotConnected [--20
Not Connected[NotConnected [-21
Not ConnectedINotConnected [=22

NotConnected [=a NotConnected [= 28

[NotConnected [=|bffNotConnected [--dT
[NotConnected [-dT ceIfNotConnected [-CT: 25
|NotConnected [--TdWNotConnected [-CT 26 |

|NotConnected [-- |e

[Ground | BlackTtGroundBlack 28

Gun Wiring

|_NotUsed | Green | Green [Green | [| Ground [Black [Black [Black |

Cy

Wiring - 2 Midway Games, Inc.

Page 54

Option Wiring (Not Part of JAMMA Harness)

| _+5vDC_|Red|Goin Door[apatT ipar Ts
| +iavoc_ [Om[CoinDoor| ePi_ [2apart [a
|_ Ground [Bik{|CoinDoor_Tapa[4par
| Coin3 | Bik-Om_[CoinDoor__ | aPi_[sfpat [a
[Cong| Bik-Yel_[CoinDoor|Pi [6] ip2i [6
[Bilin| Bik-wht_ [Coin Door8P1_ |7par7

[__Vol- | Om-Grn_| Diag Switch Conn | spa [4 [ ip2i fg [__Vol+ | Om-Red | Diag SwitchConn | ep4 [5 [ iP2i [ 8 (None) [oo J 113 TP 13: Not Used | [ (None) f= P16 _| P16: Not Used | [_ (None) JO P19 TP 19: Not Used | [__(None) J P20 | P20: Not Used |

Typical DC Power Source Voltage Limits

[Function | RangeLimits | Color | Function | Range Limits | Color_| [ Digital Circuits _| +4.90V to +5.10V ~4.75V to -5.25V

Audio, Lights+11.5V to +12.5VAuxiliaryPower | -11.5V to -12.5V

Harness Connector Prefixes [Prefix | Connector Location | __Example_|

YoCPU Boardpo iP1

[2 | Gun Interface Board ee Y 3

[4| FluorescentLamp [|4P1_
[5|Power Supply[SPA

V6 pers a

[8|Goin DoorArea|SP1_
[9[Guns (intemal)|PT

a

[ttCabinetPT
Pi2|pT

JAMMA CPU Board

NOTICE: Look for the connector prefix on wiring diagrams. The prefix shows you where you'll find the connector.

Invasion® Conversion Kit Wiring - 3

Page 55

Midway Games, Inc. BElearse auvoa Add SMa-Z NU NU Ile 1 G’vOE FOVIYZINI NNO P20]290 elehsle ais CSUN CABLE] H~21894 GUN CABLE 21894 LACK GND cage) SUPPLY INVASION. KIT

WIRING DIAGRAM

JULY 9, 1999

10 DIAGNOSTIC.

SWITCH BRACKET

EXISTING JAMMA

HARNESS

PLAYER 1

Ground. fs dreccer GUN/CABLE ASSEMBLY CABINET WIRING DIAGRAM

GUN CABLE H-21984 t1p1 PUYER 2

GUN CABLE H-21984

Page 56

CPU BOARD ASSEMBLY

=a u ~ P21 P20 Gr pis] | pia P17 P16 —

Tai oman fld

U66 } S U6?

|u57vs: | /—_——|

if us us u!

|uaafous

uaa : =

r]vieug

vie v7 i of

ula us Bigigicia a U3.

u25

INDICATOR, SWITCH AND JUMPER LOCATIONS J3

CPU Switches [Designation [Location | __ Function | _State__| __Meaning__|

Reset Switch Normal Operation P4, PS & P6 | tts | a Mode

Near Integrated Coin Mode and rear 8-Switch See DIP Switch

Circuits U60, U61 Game Banks Tables in Chapter 3 Functions

CPU Board Data

«@ BOARD REVISION LEVEL. How to determine Invasion CPU Board revision number: (1) Check PCB for paper label with part number beginning with “A-.” (2) Check EPROM revision number on white labels glued to EPROM chips.

@ JUMPERS. The CPU Board has no jumpers.

¢@ SWITCH S1 is the HARDWARE RESET switch. S1 is on the CPU Board.

¢@ TEST MODE SWITCH. The TEST MODE switch activates brief automatic tests, followed by the Menu System. You'll find TEST MODE behind the Coin Door.

Invasion® Conversion Kit Wiring - 5

Page 57

CPU LED INDICATOR TABLE

ee Power

LED 5Near U60, U71 and |+5V PowerRed||ee
(+5V)u73IndicatorOperation

(Note A) eee ‘Note B)

LED 1Near U60, U71 and | Game CodeGreen,2|eee|

(Code Version) u73 ‘Note B}

Operation oes |

Note C.
LED 2Near U60, U71 and | Sound Activity | Yellowpoftacked

(Sound) u73 Up

Fast

Slo Normal

= ee |

(Not Used)U73Note D)

NOTES:

A. LED 5 monitors a regulated power supply voltage source. + 5VDC must be on continuously.

B. aa 1 flashes the software version in Morse Code. You can also read the version off the screen in the Menu lem.

C. LED 2 (Sound) blinks during normal operation.

D. LED 3 doesn't indicate anything in this game.

Wiring - 6 Midway Games, Inc.

Page 58

SILVINSHOS GYVOE LINDHID NND

ousy ony owe oe aest vu zu as aget x ngre ASE 38 3 cay

ates nue xnez

ascot Grew rOGENZ ep QOGENZ

one noom NaN

Wiring -7 Invasion® Conversion Kit

Page 59

° < = w = ° 77) a < fo] (ia) WwW < ray va Ww Ee <

> (O]

iring - 8 Midway Games, Inc.

Page 60

~ INVASION © kir

CAUTION: This Video Game Machine (VGM) uses complex electronic components that are very sensitive to static electricity. Observe precautions below before handling electronics. Failure to do so may void the warranty and damage electronic assemblies.

¢ Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge. . © Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge this static, begin by connecting the line cord to a grounded outlet. Don't turn on the VGM! Next, touch the safety ground stud of the power supply chassis. ' « Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport VGMcircuit boards. Transport the hard drive in its shipping container.

  • Don't remove or connect electronic assemblies when cabinet power is on. Otherwise, you'll WW damage electronic assemblies and void the VGM warranty. « After you complete maintenance or service, replace ground wires, shields, safety covers, etc. Install and tighten ground and mounting screws.
Page 61

Coin Mechanism and Pricing Troubleshooting Table

REQUIRED ACTION

Improper settings at1.FromAdjustmentsMenu,choosePRICING.

Pricing Menu Verify that units and credits are set correctly. ._ Verify that coin mechanism is enabled. Consult bill validator manufacturer's literature. on bill validators Adjust pulse width on validator to fong setting. .__Retest validator operation. . Check that cabinet wiring is correct for this VGM.

Faulty wiring.Assurethatcoinmeterandcoinswitches

connect properly to control input wires from JAMMA connector and CPU wiring.

. Assure that coin meter and coin switches

Faulty coin.Verify that coin mechanism works correctly by

mechanism testing it in working VGM.

. Unlock and open cash door. Empty cash box. Improper currency Inspect revenue for counterfeit currency. . Check vault. Remove any items that block path from mechanism.

Unlockandopencoindoor.Checkeach

mechanism for proper mounting.

  • Remove mechanism.
  • Clear currency path. 4. 5. SYMPTOM

© VGM (video game machine) accepts currency or tokens, but number of credits per coin or bill is incorrect.

¢ VGM won't accept currency or tokens.

VGM won't start, Faulty coin mechanism

  • Audio and video are present.

Reinstall mechanism and latch it. Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostic Test Menu, choose SWITCH TEST. Use tests to confirm operation of switches.

  • Verify that mechanism is level after doors close.
  • Repair or replace coin door if it is bent or damaged.
  • If necessary, adjust cabinet leg levelers to keep mechanisms vertical. Bumed-out butbs may appear white or darkened. Check continuity with DVM. 2.__Replace burned-out bulb with same type.
  • Check fuse continuity with DVM.
  • If fuse is blown, replace fuse with same type. 3.__ If fuse isn't blown, check wiring. Tilted coin mechanism or VGM

Burmed-out bulb

Open fuse circuit

CAUTION: Don't remove or install any connector when power is turned on. Installation ¢ Coin indicators don't light

under power will damage the circuit boards or hard disk drive and void the warranty.

Troubleshooting - 2 Midway Games, Inc. lan

Cc)

Page 62

U

VGM Startup Troubleshooting Table

a ronson | 1. Check that VGM power switch is on. Power problem 2. Plug VGM into AC power outlet. Verify presence of AC line voltage. Tum off VGM power. Unplug AC line cord. Check Improper line voltage line voltage switch. If necessary, set it to agree switch setting with local AC line voltage. Retest VGM. Turn off VGM power. Examine AC fuse on power Open fuse chassis, under computer.

OPTIC GUN ASSEMBLY

  • Examine DC fuses on cabinet wall or electronic

(SEE ETAL DRAWMNG) g PLAST CL «© GM (video game machine) doesn't start.

« VGM appears completely non-functional.

  • No audio

equipment shelf.

  • Replace faulty fuses with identically rated parts. 4, Turn on VGM power. If fuse opens again, check DC wiring harness and connectors. Remove line cord. Test line cord, power plug, and IEC connecter for breaks or damage. Verify continuity of each wire in cord. Install cord at power chassis. Press connector firmly to seat it.
  • Assure that cabinet wiring hamess connectors fully seat in corresponding power supply and board connectors. g for breaks or damage. ¢ No illumination

© No video display

PL AND WoUNTING. BRACKET (SEE OETA DRAKING) LINE CORD (SEE "ABPUCATION CHART)

SPU ASSEMBLY (SEE DETAL ORANG}

TYPICAL LOCATION OF POWER SUPPLY AND LINE CORD

Invasion® Conversion Kit Troubleshooting - 3

Page 63

VGM Startup Troubleshooting Table, continued

a

  • Inspect CPU Board under low-light conditions. Faulty power supply LEDs glow if processor circuits receive voltage. Fan should also be operating. These indications prove presence of some DC from power supply. Still, voltages or signals may not be normal. Turn on VGM power. Using 20 Volt DC setting on digital voltmeter, measure DC voltages present at power connector pins. Adjust +5V source If necessary.
  • Using 2-volt AC setting on digital voltmeter, measure same DC voltages as above. Any reading indicates ripple or noise. In that case, service power supply. Tur off VGM power. Inspect CPU Board. Assure that JAMMA Wire Harness connector is attached and fully seated onto mating board connector. Verify connection of monitor AC power. Check seating of other harness connectors. Improper DIP switch Verify that CPU DIP Switches are set as settings intended. Verify that VGM runs and completes power-up Faulty circuit boards self-tests without errors. Note errors or failures during tests (VGM doesn't save error messages).
  • VGM (video game machine) appears non-functional.

« Currency acceptor price indicator is illuminated. N

Faulty wiring

pe

CAUTION: Don't remove or install any connector while power is turned on. Doing so will damage the CPU Board and void the warranty.

uTHis,

D.C, FUSE {ONDER GUN INTERFACE GCARC)

FUSE CONDITION LE (CN = FUSE CK) \__GUN INTERFACE EOARD ‘ASSEMELY

INTERIOR VIEW OF ELECTRONICS

Troubleshooting - 4 Midway Gaines, Inc.

Page 64

WU

WY

VGM Startup Troubleshooting Table, continued

I i Unlock and open coin door. Check each Faulty coin currency acceptor to assure proper mounting. mechanism Verify that each release latch is closed and locked. Does mechanism accept and reject currency correctly? Test mechanism with good and bad coins.

  • Inspect to see if external acceptor indicators (Pricing, Flashing Arrows, etc.) are lit.

Verify that each sccepier operates. Properly by

« VGM (video game machine) doesn't start.

e GM accepts currency or tokens.

Audio and video are present.

Enter “Menu System by Pressing and holding

TEST MODE switch inside coin door. From Diagnostic Test Menu, choose SWITCH TEST. Use tests to confirm operation of each switch in VGM. Assure that no loose parts or wires are caught in switch contacts. Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed). Replace faulty switches (bent levers, broken Assure that 70 wires are caught in hinges, latches or switch contacts.

  • Check wiring continuity from circuit board connectors to acceptors. Faulty wiring

Invasion® Conversion Kit Troubleshooting - 5

Page 65

Gun Troubleshooting Table

  • Turn off room lights to eliminate glare on
  • Players complain that one or | Lighting or sun glare monitor.
both guns fail to hit targetson screen2.Retest guns.

3.__If guns now work erly, eliminate glare.

  • Tum on room lights. Unlock and open coin door.
  • Enter Menu System by pressing and holding TEST MODE switch inside coin door.
  • From Main Adjustments Menu, choose GUN FLASH BRIGHTNESS.
  • Increase flash brightness as necessary.
  • Retest guns.
  • Repeat steps 4 and 5 until guns work prope
  • Examine gun barrel and lens for dirt or debris.
Dirty optics2.Clean lens. Don't apply cleaner directly into gun

barrel.

  • Inspect each gun for missing screws, loose or
  • GM (video game machine) | Loose or missing damaged parts, broken cables, etc.
starts normally.2.Verify that each gun operates properly by

connecting it to working VGM. 3.__If gun doesn’t work properly, repair or rep 1, Enter Menu System by pressing and holding TEST MODE switch inside coin door. From Diagnostic Test Menu, choose SWITCH TEST. Run tests to confirm switch operation.

  • Check for loose parts or wires caught in switch contacts.
  • Check continuity at each switch connection (Common to Normally Open or Common to Normally Closed),
  • Verify that gun operates properly by placing it in working VGM.
  • Check gun fuse LED on Gun Interface Board inside cabinet.
  • If LED is out, fuse is probably open. Check gun fuse on Gun interface Board. 3.__Rplace bad fuse with identically rated type.
  • Verify that each gun operates properly by SYMPTOM

Maladjusted gun software

  • Intermittent or completely ‘non-functional guns

Faulty switches

Faulty Gun Interface Board fuse

Faulty gun circuit connecting it to working VGM.

board2.If gun still doesn’t work, gun circuit board may be

bad. Repair or replace board.

NOTICE: Bright overhead lights occasionally interfere with optical gun operation. Neon lights might also interfere. To eliminate this interference, reduce light levels and adjust gun flash brightness.

Troubleshooting - 6 Midway Games, Inc.

Page 66

WU

UW

Gun Troubleshooting Table, continued

SYMPTOM | CAUSE REQUIRED ACTION

  • Check for wires caught in door hinges, latches, ¢ — Intermittent or completely Faulty wiring or switch contacts. non-functional guns 2. Verify that hamess connectors are attached and fully seated. ¢ —VGM (video game machine) starts normally,
  • Check that cabinet wiring is correct for this VGM. Assure that contro! switches connect properly to contro! input wires.
  • Assure that gun switch wires connect properly to Gun Interface Board connectors P1 and P2.
  • Check sync connection between JAMMA connector on CPU Board and sync connector on Gun Interface Board. Sync must be connected, or guns won't operate.
  • Remove screws from gun. Separate pieces at handle end first, using care not to dislodge parts. (Trigger and pump are spring loaded.) Check gun board, switches and switch connectors. Clean tens to remove fingerprints and dust. Reinstall shields removed during disassembly. After you reassemble gun, verify that good connection exists between static shield and cable ground. Check gun cable ground connections.

SIGHT"

(am L\ Ae Lo | © KS

GRIP

GUARD

TRIGGER

= GUN PARTS

Invasion® Conversion Kit Troubleshooting - 7

Page 67

Audio Troubleshooting Table

REQUIRED ACTION

  • Unlock and open coin door. Enter Menu System No audio Improper volume by pressing and holding TEST MODE switch setting inside coin door. From Main Menu, choose VOLUME ADJUSTMENT. Verify that volume levels have not been set at zero. Change levels if necessary to make VGM audible.
2.FromMainAdjustmentsMenu,choose

ATTRACT MODE SOUNDS to see if this feature is active (on). 1, From Sound Test Menu, run SOUND SYSTEM TEST. Test checks entire sound system.

  • Run power-up self-test sequence. Note errors that VGM finds during these tests. Compare circuit board LEDs with LED indicator status charts. Note discrepancies.
  • Verify proper operation of CPU Board by connecting it to working VGM.
  • \f board is faulty, replace it.
  • Check that cabinet wiring is correct for this VGM.
  • Verify that cabinet wiring provides separate e Video is present
  • VGM (video game machine) appears to operate normally

Faulty CPU Board

¢ — Constant low hum from all speakers wires (not common return) for each speaker. Check connection of all cabinet ground wires. Using 2 Volt AC setting on digital voltmeter,

measuresameDCvoltages.Anyreading

indicates ripple or noise. In that case, service power supply. Tum off VGM power. Remove grilles and check speakers. Free speaker cones, terminals, mounting screws and magnets of loose parts. Assure that speakers are FULL RANGE (100 to 10,000 Hz response) and rated for at least 20 WATTS.

  • Verify proper speaker operation by connecting speaker in question to working VGM. Multiple-speaker —_ installations: Check — for reversed wires at one speaker. Weak low frequencies and thin or hollow sound quality is symptom of incorrectly phased speakers. Sound tests may not detect this, but you can detect it during game play.
FromSoundTestMenu,choosePLAY

SOUNDS. Recheck speakers with audio signals provided by test.

  • Verify proper speaker operation by connecting speaker in question to working VGM. From Sound Test Menu, run SOUND SYSTEM TEST. Test checks entire sound system.
  • Run power-up self-test sequence. Note errors that VGM finds during these tests. Compare circuit board LEDs with LED indicator status charts. Note discrepancies.
  • Verify CPU Board operation by connecting board to working VGM. If board is faulty, replace it. Faulty wiring Verify that correct cabinet wiring is correct. Assure that all speakers connect to audio wires from JAMMA connector.

Troubleshooting - 8 Midway Games, Inc. Faulty or improper speaker

Faulty wiring

Faulty speaker

Faulty CPU Board « — Audio is distorted, muffled or has missing frequencies N « Some sounds appear to be missing

  • Dead sound channel
Page 68

WU

Video Troubleshooting Table

_ ae a Verify connection of AC Power to video monitor. Power problem Inspect CRT neck in dim light. Glowing filament near CRT base suggests some monitor circuits receive power. Voltages or signals be abnormal. Turn off AC power. Verify that video signal and Remote Adjustment Board connectors seat Properly on Video Monitor.

  • Assure that video cables connect to Video Monitor and CPU Board.
  • Assure that no wires are caught on chassis or mounting brackets.

adjustments CONTRAST are set above their minimum levels.

  • Examine AC line fuse in Video Monitor. If fuse is Faulty monitor faulty, replace it with identical fuse. circuitry 2. If fuse is good: Verify that video monitor operates correctly by placing it in working VGM.
  • If monitor is bad: Check monitor power supply.
  • Monitor appears nonfunctional

Audio is present T. Faulty wiring

  • —VGM (video game machine) controls operate normally
  • If power supply is good: Check monitor horizontal output transistor and related circuitry.
WARNING: HIGH VOLTAGE. VGM (video game machine) monitors generate and store potentially lethal high voltages. Avoid touching any part of the monitor until power has been off for some time. A picture tube can maintain a hazardous charge for up to several days. Only qualified technicians should service monitors. Turn off the power, unplug the VGM and discharge the CRT before attempting service. Even properly discharged tubes can revert to a highly charged state, without reapplication of power.
WARNING: In normal operation, the monitor doesn't require isolation from AC line voltage. During bench servicing, you may need to operate the monitor outside the cabinet. If you do, isolate the monitor from line voltage with an isolation transformer.

Invasion® Conversion Kit Troubleshooting - 9

Page 69

Video Troubleshooting Table, continued

| cAuSE REQUIRED ACTION

  • Verify that ROM instruction set is correct for this SYMPTOM

¢ VGM (video game machine) | Improper components GM. Instruction set includes more than one doesn't appear ROM. Assembly number and software version appear on each ROM's label. ¢ ~=No audio 2. Verify that CPU Board is correct for this VGM. Manufacturer name, assembly number and hardware version appear on each CPU Board. Inspect CPU Board. Assure that JAMMA cable connector seats properly into mating edge

connectoronCPUBoard.Checkcable

connectors for correct alignment and continuity.

  • Turn on VGM power. Using 20 Volt DC setting Faulty power supply on digital voltmeter, measure DC voltages at power connector pins. Verify +5V source if it is adjustable.
  • Using 2 volt AC setting on digital voltmeter, measure same DC voltages as above. Any « — Power-up self-test runs

Faulty wiring

Picture tube aperture mask is magnetized Remove diskettes from rcom. Demagnetize monitor with external degaussing coil. Take care not to magnetize neighboring VGMs. Monitor may be on or off for this procedure.

  • Tum on VGM.
  • Press and hold TEST MODE to enter Menu System. At Main Menu, select Diagnostic Menu. Then select Monitor Patterns Menu. Run through
thesescreenstofindclearestdisplayof
problem:SizingPattern(Crosshatch),Red,

Green and Blue Screen.

  • Display screen with greatest problem.
  • Display Sizing Pattern (Crosshatch) Screen.
Locatepurityandstatic convergencering

magnets on back of monitor neck. Watch screen in mirror. Adjust magnets to minimize problem. Follow instructions from monitor manufacturer.

  • Display Sizing Pattern (Crosshatch) Screen. Touch up adjustments while watching screen in mirror. « — Blotches of color appear on screen
  • — White areas in center of screen appear tinged with color Picture tube purity or static convergence is out of alignment

« Object edges have fringe of ‘one or more colors

CAUTION: Don't operate the monitor without its Remote Adjustment Board.
WARNING: HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

Troubleshooting - 10 Midway Games, Inc.

Page 70

UW

Video Troubleshooting Table, continued

SYMPTOM | CAUSE] REQUIRED ACTION White areas at screen edges Have service bureau dynamically reconverge appear tinged with color monitor. This procedure requires removing and repositioning yoke. Service bureau must follow instructions from monitor manufacturer. Picture tube dynamic convergence is out of alignment ¢ Dots at screen edges appear oval or cylindrical

Checkconnectorsandcablesforwiring

continuity. Video cables connect CPU Board to video monitor.

  • Assure connection of all cabinet ground wires, especially at video monitor chassis. Verify that video monitor operates correctly by connecting it to working VGM (video game machine). Assure that video monitor is correct type for this GM. Video monitors with wrong resolution can't lock sync. Check to see if CPU Board puts out type of sync g that your monitor requires.
ElectromagneticMovecabinetfarawayfrommachines,

fields appliances, or competitors’ VGMs.

Checkconnectorsandcablesforwiring

Video tears or rolls, or has black bar down middle of screen Faulty wiring

Faulty monitor

Nn

© Missing colors

Faultywiringcontinuityfrom circuit boards to video monitor.

Faulty monitor color Verify that video monitor operates correctly by drive circui connecting it to working VGM.

  • Tum on VGM.
One color is dimmer orMaladjusted color2.Enter Monitor Test Patterns Menu.
brighter than othersbias pots3.Watch Color Bars screen in mirror.
  • Adjust three bias pots for best colors. (Most
©Whites appear tintedmonitor neck boards include these pots.)
everywhere on screen5.If whites still seem tinted, have service bureau

rejuvenate picture tube. Watch Color Bars screen. Adjust BRIGHTNESS

«Picture is dim or fadedMaladjustedand CONTRAST pots for greatest number of

BRIGHTNESS pot or grays. You'll find these pots on Monitor Remote subnormal picture Control Board, behind coin door.

tube emission2.If pots have no effect, have service bureau

tejuvenate picture tube. Enter Monitor Test Patterns Menu. Watch Sizing Pattern (Crosshatch) Screen while adjusting WIOTH pot for best picture. You'll find this pot on Moniter Remote Control Board, behind coin door. Enter Monitor Test Patterns Menu. Watch Sizing Pattern (Crosshatch) Screen while adjusting HEIGHT pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door. If pot has no effect, service vertical output circuit. Enter Monitor Test Patterns Menu. Watch Sizing «Picture seems shifted to one | Maladjusted Pattern (Crosshatch) Screen while adjusting

sideHORIZONTALHORIZONTAL POSITION pot for best picture.

POSITION pot You'll find this pot on Monitor Remote Control Board, behind coin door.

  • Substitute working yoke.
eKeystone-shaped pictureShorted turns in yoke | 2.Have service bureau converge monitor.

3.__Retest monitor.

Invasion® Conversion Kit Troubleshooting - 11 Maladjusted WIDTH pot Picture is too narrow

Picture is too short Maladjusted HEIGHT pot or damaged vertical circuit

Page 71

Miscellaneous Problem Troubleshooting Table

SYMPTOM

  • Remove fluorescent tube from its sockets. If you
¢Marquee lamp is intermittent | Faulty fluorescentfind cracks or darkened ends, install new lamp.
or non-functionaltubeClean tube.
  • Check continuity of both fluorescent tube filaments.
  • Verify that fluorescent tube operates by placing it in working VGM. Verify that lamp pins make good connection with socket contacts.
  • Measure fluorescent lamp AC voltages. Check wiring and connector continuity from AC power chassis to lamp assembly. ._If you find faulty wiring, repair or replace it.
  • Check bottom and rear of cabinet for blocked air flow. Clear obstructions. Move VGM away from sources of heat. Turn off VGM power. Remove dust from vent holes with high-power vacuum cleaner.
Faulty wiring1.Check fan wiring and connectors.

2.__ If wiring is faulty, repair or replace it.

Faulty fan1.Check operation of all fans.

2._ If fanis faulty, replace it.

  • Press and hold TEST MODE to enter Menu ‘System. At Main Menu, enter Audits Menu.
  • Select VIEW GAME AUDITS.
  • On fourth audit screen, note WATCHDOGS «¢ VGM (video game machine) starts and plays normally

Faulty lamp fixture

Faulty wiring

*VGM operates normallyObstructed fan
  • Cabinet becomes warm after several hours of use PON

«Players complain that VGM resets intermittently Corrupt software

«Audits Menu displays anindication.
unusual number of4.If you find numerous watchdog resets, clear

watchdog resets bookkeeping totals and restore factory settings. Retest VGM.

  • If resets recur, game software may be corrupt. Test game ROMs in working VGM. If second VVGM develops reset problem, replace ROMs.
  • Tum on VGM power.
  • Using 2 volt AC setting on digital voltmeter, measure DC voltages at power connector pins. Any reading indicates ripple or noise. In that case, service power supply.
  • If power supply is OK, test CPU Board in working VGM. If second VGM develops reset blem, service CPU Board.
  • Use oscilloscope to view power line waveform. Power line problems Check for noisy power, glitches, spikes, etc.
or electromagnetic2.If you find problems, consult with your power

interference company.

  • Remove interfering appliances from VGM circuit. (These might interfere: Nearby VGMs, radio transmitters, equipment with large motors, etc.)
  • \VGM line filter should remove small power problems. If necessary, add more robust power conditioning equipment between line and VGM.
«Error messages appear onCheck any assembly (RAM, ROM, Battery, etc.)
screenFaulty hardwareidentified in error messages.
  • Call your authorized distributor for help with unresolved screen messages.

Troubleshooting - 12 Midway Games, Inc. Faulty hardware

1.

Page 72

WARNINGS & NOTICES

WARNING . © Use of non-MIDWAY parts er circuit modifications may cause serious injury or equipment damage! ¢ Use only MIDWAY authorized ccmponents and parts. Failure to do so will void your warranty and may result in incorrect or unsafe operation. Substitute parts or modifications may void the EMC directive or FCC type acceptance. ‘ © Federal copyright, trademark and patent laws protect this Video Game Machine (VGM). Unauthorized modifications may be illegal under Federal law. The moditication ban also applies to Midway Games, Inc. arid VGM logos, designs, publications and assemblies. Moreover, facsimiies of MIDWAY equipment (or any feature thereof) may be illegai under federal iaw, regardless of whether or not such facsimiles are manufactured with Midway Games, Inc. components.
WARNING oe Prevent shock hazerd and assure proper VGM operation. Plug this VGM into a properly grounded cutlet. Do not use a cheater plug to defeat the power cord’s grounding pin. Do not cut off the ground pin.
WARNING A very small portion of the population has a condition which may cause epileptic seizures or momentary toss of conscicusness when viewing certain kinds of flashing tights or pattems that are present in our dally environment. These persons may experience seizures while watching some kinds of television pictures ar playing certain video games. People who have not had any previous seizures may nonetheless have an undetected epileptic condition. lf you or anyone in your femily has experienced symptoms linked to an epileptic condition (e.g. seizures or loss awareness), immediately consult your physician before using any video games. : We recommend that parents observe thelr children while they play video games, If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or cenvulsions, discontinue use immediately and consult your physician. NOTICE This kit has been tested. It complies with limits for a Class A digital device, under FCC Rules, Part 15. These limits provide reasonable protection against harmiul interference when the equipment operates in a commercial environment. This equipment generates, uses ard can radiate radio frequency energy. If not installed and used ‘according to the instruction manual, this equipment may cause harmfu: interference to radio communications. Operation of this equipment in a residential azea is likely to Cause narmful interference. If interference occurs, the user must correct it at his own expense.

NOTICE When Midway Games, Inc. ships a VM, it complies with FCC regulations. Your label is proof of compliance. Legal repercussions to the owner or distributor may resuit if the iabel is missing or damaged. If your VGM does noi contain an FCC compliance label, call Midway Games, Inc. immediately. NOTICE You may not reproduce any part of this publication hy mechanical, photographic, or electronic means. You may not prepare phonograph recordings of this document. You may not transmit this publication or otherwise copy It for public or private use, without permission from the publisher.

COPYRIGHT & TRADEMARK NOTICE Entira contents of this manual copyright © 1999 Midway Games, Inc. All rights reserved. MIDWAY® and INVASION™ are trademarks of Midway Games, Inc.

For Service: Call your authorized Midway Games, Inc. distributor. MIDWAY GAMES INC. 3401 N. California Ave. Chicago, Iilincis 60618-5899 USA Visit our Web site at http//www.midway.com