Millipede CO-217-01 Supplement
Millipede (Atari, 1982) · Supplement · 32 pages · 29 sections · original scan
CO-217-01
Supplement to MILLIPEDE™
Operation, Maintenance, and Service Manual (TM-217, 1st printing) and Schematic Package Supplement (SP-217, 1st printing)
Table of Contents
The following pages replace the corresponding pages in TM-217.
Figure 1-2 Location of Game Switches E. Setting the Option Switches. Table 1-3 Switch Settings for Special Options Figure 1-3 Self-Test Display Table 1-4 Self-Test Procedure Self-Test Screen 1-Test Passes (text only) Table 2-3 EAROM Test Self-Test Screen 1-Test Fails (text only) .. os Cabinet-Mounted Assemblies, Upright Cabinet Parts List Cabinet-Mounted Assemblies, Ireland-Built Cabinet Parts List Adjusting the Midi Trak-Ball™ Control Video Display Upright and Ireland-Built Cabinets Parts List Figure 3-13 Removing the Printed-Circuit Boards (PCB) Printed-Circuit Board Mounting Hardware Parts List Game Printed-Circuit Board Assembly Parts List Figure 3-16 EMI Shield PCB Assembly EMI Shield PCB Assembly Parts List . . Figure 3-17 Power Supply (figure no. only)
The following diagrams reflect changes made to SP-217.
Color Memory Address Selectors Sheet 6A Color Output Sheet 6A Coin Counter & LED Output Sheet 7A
The text and tables below provide information on using the CAT Box.
Troubleshooting with the Read/Write Controller Troubleshooting with Signature Analysis Troubleshooting with Checksums .. Troubleshooting with Watchdog Circuit
‘Set-Up Procedures
- Installation Requirements
Power 150 W Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Upright Cabinet 62 x 85 cm (25 % x 33 % in.) 186 cm (73 in.) Ireland-Built Cabinet Space Required 60 x 68 cm (24 x.27 in.) Game Height 170 cm (67 in.) Space Required Game Height
- Selecting the Voltage Plug The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voltages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Next, check the wire color on the voltage selection plug that is plugged into your power supply. Make sure the voltage selection plug is correct for the voltage of your location (see Figure 3-16). Now, plug the game into a grounded 3-wire outlet. Millipede™
D. Locating the Switches
- On/Off Switch
The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-2).
- Utility Panel Switches The volume control, self-test switch, coin counter(s), and auxiliary coin switch are located on the utility panel (inside the upper coin door). Refer to Figure 1-2. Use the volume control to adjust game audio. Use the self-test switch to place the game in the Self-Test Mode. Use the coin switch to credit the game without activating a coin counter.
- Option Switches Option switches are located on the game PCB (see Figure 1-2).
- Price options are at PCB location B5.
- Play options are at PCB location D5.
- Special options are at PCB location P8.
UTILITY PANEL See Figure 3-11
COIN COUNTER
SELF-TEST SWITCH
VOLUME CONTROL| (To increase, turn clockwise)
AUXILIARY COIN SWITCH POWER ON/OFF ‘SWITCH OPTION SWITCHES
SWITCH AT BS (Game price)
‘SWITCH AT D5 (Game play)
SWITCH AT P8 (Special options)
OPTION SWITCHES
Figure 1-2 Location of Game Switches
1-4
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Millipede™
E. Setting the Option Switches
Tables 1-1, 1-2, and 1-3 contain settings of the game option switches. Options preset at the factory are shown by the < symbols. However, you may change the settings according to your individual needs. To verify option switch settings, set the self-test switch to the on position. Compare the information on the screen to the option switch settings listed in the Tabie 1, Table 2, and Table 3. Then set the selftest switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism multipliers, and bonus play. These switches are on the game PCB at location B5. Set-Up Procedures
The multipliers (switches 3-5) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. After this inspection, the mechanism either accepts or rejects the coin. The coin door has two mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1. You may offer bonus play for certain combinations of coins inserted. For example, with the game set at $.25 per play, players who deposit four successive $.25 coins before pressing the start switch can receive a bonus play. The bonus feature encourages players to insert more money than the minimum $.25 required for one game.
Table 1-1 Switch Settings for Price Options
- Settings of 8-Toggle Switch on Millipede™ PCB (at B5) 7 6 5 4 3 2 1 Option
On On Off Off
| On | Off | On |
| On | Off | Off |
| Off | On | On |
| Off | On | Off |
Off Off On
| Off | Off | Off |
Off On
Off Off
Off On
On Off On On On On. On Off
Demonstration Mode For every 3 coins inserted, logic adds 1 more coin For every 5 coins inserted, logic adds 1 more coin For every 4 coins inserted, logic adds 2 more coins For every 4 coins inserted, logic adds 1 more coin For every 2 coins inserted, logic adds 1 more coin No Bonus Coins @ Left coin mechanism x 1 <4 Left coin mechanism x 2 Right coin mechanism x 1 < Right coin mechanism x 4 Right coin mechanism x 5 Right coin mechanism x 6 2 coins for 1 credit 1 coin for 1 credit < 1 coin for 2 credits Free Play
“4Manufacturer's recommended settings
SUE
Table 1-2 details switch settings for Select Mode, game difficulty, number of lives, and bonus life options. The switches are on the game PCB at location D5. The Select Mode (switch 8 at location D5 is off) allows a player to start a game at an advanced level of play. He receives points for starting play at that level. The maximum level that the player may select will be the bonus Jevel below the last level achieved, up to a maximum of 300,000. For example, if the player scores 46,000 points, and the bonus life setting is at 15,000 (switch 5 is on and switch 6 is off), his last bonus was at 45,000. Therefore, he may select a starting score of 0, 15,000, or 30,000 points, In the easy spider setting (switch 7 is off), the spider moves slowly for the first 10,000 points. In the hard spider setting (switch 7 is on) the spider moves slowly for the first 5,000 points. After 5,000 points the spider moves rapidly.
Set-Up Procedures
In the easy beetle setting (switch 2 is off), the beetle moves slowly until 400,000 points, and four beetles appear in each wave after 500,000 points. In the hard beetle setting (switch 2 is on), the beetle moves slowly until 300,000 points, and four beetles appear in each wave after 350,000 points. Millipede™
In the easy millipede head setting (switch 1 is off), millipede heads enter from the sides of the screen at timed intervals. In the hard millipede head setting (switch 1 is on), millipede heads enter from the sides of the screen faster than in the easy setting.
Table 1-2 Switch Settings for Play Options
« Settings of 8-Toggle Switch on Millipede™ PCB (at D5)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
Option
Off
Off On
Off Off
Off On
On Off On On
On Off On On Select Mode < No Select Mode Easy spider < Hard spider Bonus life every 12,000 points Bonus life every 15,000 points < Bonus life every 20,000 points No bonus life 2 lives per game 3 lives per game < 4 lives per game 5 lives per game Easy beetle < Hard beetle Easy millipede head < Hard millipede head
<Manufacturer’s recommended settings
Table 1-3 details option settings for coin counters, minimum credits, Select Mode starting scores, and language. The switches are on the game PCB at location P8. You may choose the Select Mode starting score with switches 3 and 4. Make sure to enable the Select Mode by setting switch 8 at PCB location D5 to is off. The starting scores you may choose are 0, the amount of the bonus life setting, or multiples of the bonus. For example, with the bonus life setting at 15,000 points and the Select Mode starting score at 3 x bonus life level, the player may choose a starting score of 0, 15,000, 30,000 and 45,000 points.
Table 1-3 Switch Settings for Special Options
Settings of 8-Toggle Switch on Millipede™ PCB (at P8)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | Option |
On 1 coin counter - U.S. only Off 2 coin counters On 1 credit minimum << Off 2 credit minimum Select Mode Starting Score
| R | Boon | On | 0 points | |
| 3 | $ | On | Off | 0 and bonus life level |
| S | 3s | Off | On | 0, bonus life level, and 2 x bonus life level < |
| = | = | Off | Off | 0, bonus life level, and 2 x bonus life level, and 3 x bonus |
life level
| On | On | English < |
| On | Off | German |
Off On French
Off Off Spanish
“<Manufacturer's recommended settings
Millipede™
F. Performing the Initial Self-Test
This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is . necessary.
We suggest you perform the self-test procedure
when you first set up the game, any time you collect money from the game, when you change game options, or when you suspect game failure. Set-Up Procedures
Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test.
Refer to Figure 1-2 to locate the self-test switch and option switches. Set the self-test switch to the on position (see Figure 1-3) to see the Self-Test Display in the Self-Test Mode. To end the Self-Test Mode, Set the self-test switch to the off position.
The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. \f a part of the test described in Table 1-4 fails, refer to Chapter 2.
LANGUAGE MINIMUM CREDIT (Blank means 1 minimum), CHARACTER SET
GAME COST. COIN MECHS —__ ee BONUS a (Blank means no bonus) _ SE _ eee Beertes. MILLIPEDE HEAD SETTING Fa BBS BEETLE SETTING Sor NO. OF LIVES BONUS LEVEL SPIDER SETTING SELECT MODE: MAXIMUM STARTING VALUE TOTAL NO. OF GAMES
TRAK-BALL™ MOVEMENT
JOYSTICK MOVEMENT
SWITCH NOS. E=—— con SWITCHES
— CONTROL
fea PANEL
8 al SWITCHES
SWITCH AT ps—id ‘NOT USED
(Game Play) \ TRAK-BALL™ (or Joystick) SWITCH AT BS DIRECTION (Game Price) SWITCH AT P8 (Special Options)
Figure 1-3 Self-Test Display
Set-Up Procedures Millipede™
Table 1-4 Self-Test Procedure Instruction Test Passes
- Set the self-test switch to on (see Figure 1-2). All credits will be cancelled.
- Press each contro! panel and auxiliary coin switches. Insert coins into both coin slots (coins will not be counted on the coin counter). -3, Roll the Midi Trak-Bali™
4, Press the 1-player start switch at least 64 times.
- Press the 1-player start switch eight times.
- Observe 16 blocks of color in the character set on right side of the screen.
- Press the 2-player start switch and the FIRE switch.
- Roll the Midi Trak-Ball™ and press 2-player start switch 16 times.
- To erase the EAROM (erases the high-score table and game statistics), simultaneously press both start switches and FIRE,
- To end the test, set the self-test switch to off. The self-test display appears. RAMs and ROMs are tested. The start LEDs remain on during the test. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self-Test Procedure. When you press a switch, the appropriate 1 changes to 0 on the screen and you will hear a high tone. If the test fails refer to Chapter 2.
A motion object picture moves around on the screen in directions corresponding to the Midi Trak-Ball™ If the test fails, refer to Chapter 2. Each time you press the 1-player start switch, a tone occurs. The motion object changes shape and the background changes color. If test fails refer to Chapter 2. You will hear a high tone and the background will change color each time you press the 1-player start switch. If the test fails refer to Chapter 2. Each of the 16 blocks should contain a different color. If test fails refer to Chapter 2. Playfield objects change color with each press of FIRE or 2-player start switch and a tone occurs. If test fails refer to Chapter 2. Each time you roll the Midi Trak Bali™ and press 2-player start switch a Motion object is moved from the diagonal group of objects in the center of the screen and placed in a new location on the screen. Test for 16 motion objects in this manner. If test fails refer to Chapter 2, The message EA FF appears in the upper left corner of the screen. The message remains on the self-test screen until the next game is completed and the EAROM is rewritten.
Self-Test Procedure
A. Comments on Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio I! printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you find no harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting the PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram.
B. Performing the Self-Test
This game will test itself and provide data to show that the game's circuitry and controls are operating Properly. The data is provided on the video display and speaker. No additional equipment is necessary. To switch to the Self-Test Mode, set the self-test switch, located on the utility panel, to the on position. Millipede™
SELF-TEST SCREEN 1—Test Passes: If the test passes, the screen displays the picture in Figure 2-1—Test Passes. See Chapter 1, Section F, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off. Press the auxiliary coin switch and set the S-T switch to on. To see self-test screen three, press the auxiliary coin switch.
ENGLISH FREE PLAY il
POOOOL DOL 100001 OO1LLOL 1LOO111 OOOLLL OOOLOL OOOO1LL
173 PLAYS 1:48 GAME TIME OMNALHE AK RZOVOAYACCEXIN I -- BUD DOS SeNw. FS
Figure 2-1 Self-Test Screen 1— Test Passes
Millipede™
SELF-TEST SCREEN 1—Test Fails:
RAM failure is indicated by a blank or “garbage’’-filled screen and a number of tones. Count the tones to determine the failed RAM. The tone number and matching RAM location are shown in Table 2-1. The number of tones continue to repeat. Replace the failed RAM and restart the test (set the self-test switch to off, and then to on).
Table 2-1 Locating the Failed RAM
Failed RAM Location on Game PCB Number of Tones
F2 £2 M2 Na BeE@BnNeD oeons = FS
a &
ROM failure is indicated by two groups of alphanumeric characters in the upper left corner of the screen (see Figure 2-2). The group at the far left indicates the location of the failed ROM/PROM. Ignore the group at the right of the ROM number. The failed ROM and its location are listed in Table 2-2.
Table 2-2 Location of Failed ROM
Failed
Screen ROM Location
Display on Game PCB
RI M/N1 R2 uu R3 JiK1 Ra H1 EA P2 PO D4 PI B4
EAROM failure is indicated by the absence of game accounting statistics. When you erase the EAROM (by simultaneously pressing both start switches and Fire), the message EA FF should appear in the upper left corner of the self-test screen. The message will remain on the self-test screen until the next game is completed and the EAROM is rewritten. At this time, the self-test screen should contain game accounting statistics. If there are no statistics, suspect the EAROM at P2 or associated circuitry, and troubleshoot using game schematics. Self-Test Procedure
ENGLISH
FREE PLAY
EASY CEMCN Gee
OOOOOL LOO00L OO11LOL 3 te
OOOOLL
173 PLAYS 1: GAME TIME T
R Ql p O1 Ni Mi Uy kK J I HE G F E D. ¢. Bi a Fi is ¥4
bs] 4) di
Figure 2-2 Self-Test Screen 1— Test Fails
SWITCH failure is indicated by the appropriate 7 not changing to a 0 on the screen when you press a switch. There may be a constant tone, or no tone at all. Check if the volume control is turned off. Or check the switch, loose harness or connector wires, or the custom audio I/O chip. Troubleshoot using the information in Chapter 3, Section B, and the game schematics. MIDI TRAK-BALL™ failure is indicated by no movement or jerky movement of the player's shooter when you roll the Midi Trak-Ball™. If the cursor fails to move, or if movement is reversed or jerky, suspect the Midi Trak-Ball™ or the harness (see Figure 3-5). SOUND failure is indicated by the absence of any sound when any of the control panel or coin switches are pressed. Press the 1-player start switch 8 times to test all 8 channels. No increase in volume or change in pitch, or no tone when you press and hold the 2-player start switch and press the 1-player start switch, indicates failure. Suspect the volume control on the utility panel, the custom I/O chips, or troubleshoot using the game schematics.
2-3
Self-Test Procedure
COLOR failure is indicated by no color change in the background or playfield objects. Background color should change when you press the 1-player start switch. Playfield and motion objects should change when you press the 2-player start switch and FIRE switch. Troubleshoot using the game schematics and the video display manual. MOVING OBJECT failure is indicated when the object represented as the shooter does not change shape each time you press the 1-player start switch. Press the 1-player start switch 64 times to see all shapes. Suspect the EPROM may be bad, or troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off, then press the auxiliary coin switch and the self-test switch to on.
SELF-TEST SCREEN 2: This screen displays 64 rectangles, each with varying intensities of red and blue (see Figure 2-3). The column on the left edge of the screen should show eight shades of blue from black at the bottom to bright blue at the top. The bottom row should show eight shades of red from black at the left to bright red at the right. The remainder of the screen shows blends of red and blue. Adjust the color guns (see the video display manual) so the lower left corner is black and the other corners are bright blue and red.
Figure 2-3 Self-Test Screen 2
2-4 Millipede™
Press FIRE and the screen displays 64 intensities of green. The lower left corner should be dark green. Press FIRE again, and the green becomes more intense. Press FIRE a third time, and the green becomes even more intense. The upper right corner should now be white.
SELF-TEST SCREEN 3:
Press the auxiliary coin switch and the screen displays a test pattern with white dots on a black background (see Figure 2-4). Troubleshoot convergence using the video display manual.
Figure 2-4 Self-Test Screen 3
Millipede™ Maintenance, Repair, and Parts
Cabinet-Mounted Assemblies Upright Cabinet Parts List
Assemblies and components in the following parts list are shown in Figure 3-1.
Part No. Description A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037455-03 Strain-Relief Power Cord (Australia and New Zealand) A037470-01 Power On/Off Switch/Mounting Plate Assembly A037701-01 EMI Cage Assembly 03778403 Strain-Relief Power Cord (United Kingdom, Ireland, Lebanon, Saudi Arabia, India, Hong Kong, Singapore, Egypt, Nigeria, Republic of South Africa, Zimbabwe) A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039259-01 Main Harness Assembly A039260-01 Power Harness Assembly A039301-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039502-01 Electromagnetic Interference (EMI) Shield PCB Assembly The following four items are the technical information supplements to this game: SP-217 Millipede Schematic Package ST-217-01 Millipede Label with Self-Test Procedure and Option Switch Settings TM-217 Millipede Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) Acceptable substitute is TM-210, use with part no. 139003-1006 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, Y-Inch Wide x %-Inch Thick (not shown) 78-3201 Adjustable Glide 009992-01 On/Off Switch Cover 037332-01 Ventilation Grille 038091-01 Molded Coin Box 038178-03 Dual-Slotted PCB Cleat 038870-01 Metal Coin Box Enclosure 039317-01 Video Display Shield 039349-01 Rear Access Panel (does not include lock) 178013-001 Spring Draw Latch (not shown) 178034-024 %4-Inch Black Plastic T-Molding 178048-001 2-Inch Rigid Caster
Millipede™ Maintenance, Repair, and Parts
Cabinet-Mounted Assemblies Ireland-Built Cabinet Parts List
Assemblies and components in the following parts list are shown in Figure 3-2.
Part No. Description A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A037470-01 Power On/Off Switch/Mounting Plate Assembly A038854-01 Power Harness Assembly A038881-01 Lock Assembly (for rear access panel) A039257-01 Main Harness Assembly A039448-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) The following four items are the technical information supplements to this game: SP-217 Millipede Schematic Package ST-217-01 Millipede Label with Self-Test Procedure and Option Switch Settings TM-217 Millipede Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) Acceptable substitute is TM-210, use with part no. 139003-1006 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %-Inch Thick (not shown) 009992-01 On/Off Switch Cover 038091-01 Molded Coin Box 038240-1800 Printed Circuit Board Cleat 038770-01 Metal Coin Box Enclosure Acceptable substitute is part no. 038781-01 038790-01 Front Video Display Support Bracket (not shown) 038805-01 Display Shield Retainer (not shown) 038976-02 Rear Access Panel (does not Include lock) 038986-01 Attraction Panel Retainer 038988-01 Ventilation Grille 038992-01 Display Shield 039009-01 Rear Video Display Support Bracket (not shown) 178013-002 Spring Draw Latch 178034-024 %4-Inch Black Plastic T-Molding
Maintenance, Repair, and Parts
Lubricating the Midi Trak-Ball™ 1. Remove the entire Midi Trak-Ball™ assembly from the control panel (see Figure 3-4). Remove the six screws that secure the upper and lower frames together (see Figure 3-5). Lift off the upper frame. Lubricate each of the six ball bearings with two drops of a light-duty oil, such as 3-in-One oil. Lubricate the bearings approximately every three months or 6,000 credits (credits are counted on the coin counter).
Removing the Midi Trak-Ball™ Coupler PCB, and Encoding Wheel:
4.
5. Follow steps 1 and 2 above. Then remove the Midi Trak-Ball™, Lift the PCB out of its slot. Carefully disconnect the ted connector and remove the PCB. Millipede™
Remove the socket-head screw, flat washer, and splitlock washer that secure the encoding wheel. Remove the encoding wheel. Reassemble and reinstall in reverse order.
Adjusting the Midi Trak-Ball™ Control: 9.
10. When you tighten the encoding wheel, rotate the socket-head screw on the end of the roller shaft until a hole in the shaft is visible through the hole in the top of the frame. Insert a ¥%-inch diameter pin or screwdriver through the hole in the shaft. . Tighten the socket-head screw with an Allen wrench.
Midi Trak-Ball™ Assembly Parts List
Part No. Description
A035220-02 Coupler PCB Assembly (includes Radial Optical Coupler) A036096-01 Harness Assembly 72-8406 #4-40 x ¥;Inch, Hex Socket-Head Steel Machine Screw 75-0148 #4 Flat SAE-Standard, Zinc-Plated Steel Washer 75-044S #4 Split-Lock, Zinc-Plated Steel Washer 034168-01 Label with Lubrication Instructions (not shown) 035937-01 Ball Bearing (6 per assembly) 035938-01 Etched Encoding Wheel 038039-01 Upper Black Plastic Frame 038040-01 Lower Black Plastic Frame 038041-01 Roller Shaft 038042-01 Idler Shaft 038043-01 Midi-Trak-Ball (3-inch diameter) 139002-001 Radial Optical Coupler (located on the Coupler PCB Assembly) 176010-106 #8 x %;Inch Cross-Recessed, Pan-Head, Zinc-Plated Stee! Screw
3-10
Millipede™ Maintenance, Repair, and Parts
Video Display Upright and Ireland-Bulit Cabinets Parts List
Assemblies and components in the following parts list are shown in Figures 3-9 and 3-10.
Part No. Description For Upright Cabinet 037750-01 Display Support Bracket 039317-01 Display Shield 039320-01 Display Bezel 139003-1004 19-Inch Matsushita Color Raster-Scan Display Acceptable substitute is part no. 139003-1004, For Iretand-Bullt Cabinet 039018-01 Display Bezel 038790-01 Front Display Support Bracket 038805-01 Display Shield Retainer 038992-01 Display Shield 039009-01 Rear Display Support Bracket 139003-1004 19-Inch Matsushita Color Raster-Scan Display Acceptable substitute is part no. 139003-1006
Maintenance, Repair, and Parts
G. Printed-Circuit Boards
A— warninc—A, Before you remove or repair any printed-circuit board (PCB), switch the game to off.
Removing the Printed-Circuit Boards:
1. 2. Open the rear access panel. The Upright game PCB is located inside the electromagnetic interference (EMI) cage (see Figure 3-13). Unplug the two edge connectors on the EMI shield PCB. To remove the PCB, pull the eight nylon snap-in fasteners on the EMI shield PCB to the unlocked position. Carefully slide the shield PCB with attached game PCB straight out of its guide. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCBs. 7. 8. Millipede™
To remove the /reland-Built game PCB, remove the screw and two washers that secure the PCB to the cabinet. Carefully slide the PCB straight out of its retainer. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCB. To remove the Regulator/Audio |! PCB, first disconnect the five small harness connectors on this board. Remove the hardware that secures the Regulator/Audio I! PCB to the cabinet, and carefully remove the board from its retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required, and reinstall the PCB.
Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
Close and lock the rear access panel.
Game PCB Removal “OD from EMI Cage
The Federal Communications Commission requires that the game PCB be housed in the EMI cage with the Shield PCB attached.
03770102 (EMI Cage)
T2-1604F (Screw) 724404F (Screw)
GAME ve
037873-01 (Spacer) EMI SHIELD PCB 038178-03, (Retainer)
176015-110 (Screw)
‘A038874-21 (Milipede™ game PCB)
‘A039430-01 (Shield PCB)
175009-221 ma (Washer)
- 178045-442 (Fastener) 178044-242 (Grommet)
Figure 3-13 Removing the Printed Circuit Boards (PCBs)
3-22
Millipede™ Maintenance, Repair, and Parts
Regulator/Audio Il PCB Removal Game PCB Removal Without EMI Cage
72.6810S (Screw) 72-6810S 175004-708 (Screw) 476015-110 (Washer) (Screw)
034536-02 (Foam pad)
175004-708 A035435-04 (Washer) (Regulator! Audio 11 PCB)
Figure 3-13 Removing the Printed Circuit Boards (PCBs)
Printed-Circuit Board Mounting Hardware Parts List
Assemblies and components in the following parts list are shown in Figure 3-13.
Part No. Description Upright Cabinet 03770102 Electromagnetic Interference (EMI) Cage (includes guide) A039430-01 EMI Shield PCB 72-1404F #4-40 x ¥4-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x %4-Inch Cross-Recessed Steei Screw 037873-01 Spacer 038178-03 Dual-Slotted Retainer 175009-221 Plastic Washer 176015-110 #10 x %Inch Cross-Recessed Pan-Head Screw 178044-242 Grommet 178045-442 Snap-In Fastener Plastic Guide
Upright and Ireland-Built Cabinets 7268108 #8 x %Inch Cross-Recessed Pan-Head Screw 034536-02 Foam Pad 175004-708 #8 Fiber Washer
3-23
Millipede™
Millipede™ Game Printed-Circuit Board Assembly Parts List, continued Maintenance, Repair, and Parts
| Designator | Description | Part No. |
| 9H, OJ | Type-74LS74 Integrated Circuit | 37-74LS74 |
| OK | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 9M, 9N | Type-741.S257 Integrated Circuit | 37-74LS257 |
| 9P | Type-74LS191 Integrated Circuit | 37-74LS191 |
| 10C | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 10D | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 10E | Type-74LS00 Integrated Circuit | 37-74LS00 |
| 10F | Type-555 Timer Integrated Circuit | 37-555, |
| 10K, 10L | Type-74LS257 Integrated Circuit | 37-74LS257 |
| 10N | Type-4584B Hex Schmitt Trigger Integrated Circuit | 37-4584B |
| 10P | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 10R | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 11F | Dual Operational-Amplitier Integrated Circuit | 37-LM324 |
| 11H | Quad Operational-Amplifier Integrated Circuit | 37-TLO82CP |
| 11P | Type-4584B Hex Schmitt Trigger Integrated Circuit | 37-4584B |
| 12A | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 12B | Type-74LS27 Integrated Circuit | 37-T4LS27 |
| 12C | Type-7406 Integrated Circuit | 37-7406 |
| 12D | Type-7407 Integrated Circuit | 37-7407 |
| 12E | Type-74LS259 Integrated Circuit | 37-74LS259 |
Programmable Read-Only Memories
| 4H | Erasable Programmable Read-Only Memory | 136013-101 |
| WiK | Erasable Programmable Read-Only Memory | 136013-102 |
| 4b | Erasable Programmable Read-Only Memory | 136013-103 |
| AMIN | Erasable Programmable Read-Only Memory | 136013-104 |
| 7E | Programmable Read-Only Memory | 136001-213 |
Random-Access Memories
| 2E, 2F | Random-Access Memory | 90-7033 |
| 2J-2M | Random-Access Memory Acceptable substitute is part | 137250-001 |
no. 137250-002
| 4K-4N | Random-Access Memory Acceptable substitute is part | 137250-001 |
no. 137250-002
| 8B | Random-Access Memory Acceptable substitute is part no. | 137178-001 |
137271-001
| 10A, 10B | Random-Access Memory | 90-7005 |
| 11B, 110 | Random-Access Memory | 90-7005 |
Read-Only Memories
| 2P | Electrically-Alterable Read-Only Memory | 137161-001 |
| 5P | Read-Only Memory | 136013-109 |
| 5R | Read-Only Memory | 136013-110 |
(Continued on next page)
3-27
Maintenance, Repair, and Parts Millipede™
Millipede™ Game Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
Resistors
| R1, R2 | 10 KQ, +5%, % W Resistor | 110000-103 |
| R3 | 220 2, +5%, % W Resistor | 110000-221 |
| R4 | 1 KQ, +5%, % W Resistor | 110000-102 |
| RS | 10 K2, +5%, % W Resistor | 110000-103 |
| R6 | 22 KQ, +5%, % W Resistor | 110000-223 |
| R7 | 1 KQ, +5%, % W Resistor | 110000-102 |
| R8 | 220 Q, + 5%, Y% W Resistor | 110000-221 |
| R9-R19 | 1 KQ, +5%, V4 W Resistor | 110000-102 |
| R20-R27 | 470 2, +5%, % W Resistor | 110000-471 |
| R28-R43 | 1 KQ, +5%, % W Resistor | 110000-102 |
| R44-R46, | 470 2, +5%, Vs W Resistor | 110000-471 |
| R47 | 1.2 KQ, +5%, Vs W Resistor | 110000-122 |
| R48 | 470 Q, +5%, %4 W Resistor | 110000-471 |
| R49 | 1.8 KQ, +5%, % W Resistor | 110000-182 |
| R50, R51 | 3.9 KQ, +5%, % W Resistor | 110000-392 |
| R52 | 82 2, +5%, v4 W Resistor | 110000-820 |
| R53 | 1.2 KQ, +5%, V4 W Resistor | 110000-122 |
| R55 | 1.8 KQ, +5%, % W Resistor | 110000-182 |
| R56 | 3.9 KQ, +5%, % W Resistor | 110000-392 |
| R57 | 82 Q, +5%, % W Resistor | 110000-820 |
| R58 | 1.2 KQ, +5%, V4 W Resistor | 110000-122 |
| R60 | 1.8 KQ, +5%, % W Resistor | 110000-182 |
| R61, R62 | 3.9 KQ, +5%, V% W Resistor | 110000-392 |
| R63 | 82 Q, +5%, Vs W Resistor | 110000-820 |
| R64-R66 | 270 2, +5%, V4 W Resistor | 110000-271 |
| R70-R76 | 470 2, +5%, Ys W Resistor | 110000-471 |
| R77-R83 | 1 KQ, +5%, % W Resistor | 110000-102 |
| R84-R91 | 3.3 KQ, +5%, Vs W Resistor | 110000-332 |
| R92-R108 | 10 KQ, +5%, % W Resistor | 110000-103 |
| R109, R110 | 1 KQ, +5%, % W Resistor | 110000-102 |
| R111, R112 | 220 Q, +5%, % W Resistor | 110000-221 |
| R113-R119 | 470 Q, +5%, % W Resistor | 110000-471 |
| R120-R152 | 10 KQ, +5%, % W Resistor | 110000-103 |
| R153 | 220 2, +5%, % W Resistor | 110000-221 |
| R154 | 100 K2, +5%, % W Resistor | 110000-104 |
| R155, | 1 KQ, +5%, % W Resistor | 110000-102 |
| R156-R158 | 39 KQ, +5%, % W Resistor | 110000-393 |
| R159 | 220 2, + 5%, % W Resistor | 110000-221 |
| R160 | 68 KQ, +5%, % W Resistor | 110000-683 |
| R161, R162 | 1KQ, +5%, % W Resistor | 110000-102 |
| R163 | 470 Q, +5%, Ys W Resistor | 110000-471 |
| R164 | 10 KQ, +5%, % W Resistor | 110000-103, |
| R165 | 39 KQ, +5%, %4 W Resistor | 110000-393 |
| R166-R170 | 1KQ, +5%, % W Resistor | 110000-102 |
(Continued on next page)
3-28
Millipede™ Maintenance, Repair, and Parts
Millipede™ Game Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R171, R172 | 1.8 KQ, +5%, % W Resistor | 110000- 153 |
| R173, R174 | 1 KQ, +5%, % W Resistor | 110000-102 |
| R175-R177 | 100 KQ, +5%, % W Resistor | 110000-101 |
Sockets
| 1H, 1L, 1M/N | 24 Contact, Medium-Insertion-Force IC Socket | 79-42C024 |
| 2c | 40 Contact, Medium-Insertion-Force IC Socket | 7179-42040 |
| 2P | 22 Contact, Medium-Insertion-Force IC Socket | 79-42C22 |
| 4B, 4D | 40 Contact, Medium-Iinsertion-Force IC Socket | 79-42C40 |
| 5P, 5R | 24 Contact, Medium-Insertion-Force IC Socket | 79-42624 |
Switches
| 5B, 5D, 8P | 8-Station, Single-Throw, Dual-Inline-Package Bit Switch | 66-118P1T |
Transistors
| Q1-a4 | Type-2N3904, 60 V, 1 W, NPN Transistor | 34-2N3904 |
| es} | Type-2N3906, 40 V, 1 W, PNP Transistor | 33-2N3906 |
| Q6, Q7 | Type-2N6044 Darlington NPN Transistor | 34-2N6044 |
| 8, 9 | Type-2N3906, 40 V, 1 W, PNP Transistor | 33-2N3906 |
Miscellaneous
| L1-L3 | 100 wH Inductor Acceptable substitute is part no. 41-3003 | 141002-001 |
| L4-L6 | 1.0 pH Inductor | 141007-001 |
| VAI | Voltage Regulator | 37-7815 |
| vVR2 | Voltage Regulator | 37-7915 |
| ¥1 | 12.09 MHz Crystal | 144000-001 |
Test Point Acceptable subsiitute is part no. 020670-01 179051-002 Nylon Snap-In Fastener 81-4302
3-29
Millipede™ Maintenance, Repair, and Parts
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction fomiden without the speciic written permission of Atari, Inc., Sunnyvale, CA. This drawing is ‘only conditionally issued, and ‘neither receipt nor possession thereof confers or transfers. any right in, or license fo use, the ‘subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, {nc., and for manufacture under the corporation's written license, ‘no right to reproduce this drawing is granted or the subject matter thereof uniess by written agreement with or written permission from the corporation.
Figure 3-16 EMI Shield PCB Assembly A037430-01 A
3-33
Maintenance, Repair, and Parts Millipede™
EMI Shield PCB Assembly Parts List
Components in the following parts list are shown in Figure 3-16.
| Designator | Description | Part No. |
Capacitors
| C1, C2 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C3, C4 | 0.1 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| cS | 0.01 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C6-C18 | 0.01 yF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C19-C23 | 0.01 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C24-C36 | 0.1 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| c37 | 0.01 uF, + 80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C40 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C41 | 0.01 pF, + 80%, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C42 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C43, | 0.01 uF, +80%, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C47 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C49-C52 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C53-C56 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C58-C60 | 1000 pF, + 80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-102 |
Acceptable substitute is part no. 122002-102
| C62-C64 | 470 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-471 |
Acceptable substitute is part no. 122013-471
Connectors
| P19 | 24-Pin Card-Edge Connector | 179073-024 |
| P20 | 44-Pin Card-Edge Connector | 179073-044 |
Miscellaneous #4-40 x Y2-Inch Cross-Recessed Pan-Head Machine Screw (not shown) 72-1408C #4 Flat Washer (not shown) 75-024C #4-40 NutiWasher Assembly (not shown) 75-99514
3-34
Millipede™ Maintenance, Repair, and Parts
H. Power Supply Assembly
A021084-xx (Voltage plugs) 29.053 (Capacitor) "1 (Fuse block cover)
79-4411001 (Fuse post) 78-70501SC. (Capacitor bracket) 46-2017002 (Fuse)
A035891-02 (Fuse harness assy) 034482.02 (Chassis)
46-301203 (Fuse)
78-2708 (Bushing)
(Filter Assy.) 79-3206 (Fuse block) 037641-01 46-2014002 (Label) rh (Fuses)
79-15021001 <6 01 (Terminal block) roe i hares)
A034629-01 3A-MDA3501 ® (Rectifier) (AC harness)
Figure 3-17 Power Supply Assembly A037671-01 & -02 E
3-35
Maintenance, Repair, and Parts Millipede™
Power Supply Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-17
Part No. Description A021084-01 Voltage Plug for 100 V (90-110 VAC) (violet wire color—plugs into J3) A021084-02 Voltage Plug for 120 V (105-135 VAC) (yellow wire color—plugs into J3)* A021084-04 Voltage Plug for 220 V (200-240 VAC) (biue wire color—plugs into J3) A021084-05 Voltage Plug for 240 V (220-260 VAC) (brown wire color—plugs into J3' A034629-01 AC Harness Assembly (J4A) A034630-01 RFI Filter Assembly (FL1i—designation not marked) A035888-01 Transformer Assembly (T1—designation covered) (Acceptable substitute is part no. A ) 4035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6) 29-053 27,000 uF, 15 VDC Electrolytic Capacitor (C1) 3A-MDA3501 Type-MDA 3501 Bridge Rectifier (CR1) 46-2014002, 4 A, 250 V, 3AG Slow-Blow Glass CartridgeType Fuse (F2, F4-F6) 46-2017002 7 A, 250 V, 3AG Slow-Blow Glass CartridgeType Fuse (F1) 46-301203 20 A, 32 V, 3AG Slow-Blow Glass CartridgeTypeFuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with ¥-Inch Inside Diameter x %,-Inch Outside Diameter x %-Inch Thick 78-70501SC_ 2-Inch Diameter Capacitor Mounting Bracket (C1) 79-15021001 2-Circuit Single-Row Terminal Block (located under F4) 79-3206 5-Position 3AG Fuse Block with ¥-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG CartridgeType Fuse Post (F1) 03448202 Power Supply Chassis Base 034544-01 Fuse Block Cover (F2-F6) 03724301 Metal Base Plate (not shown in illustration) 037639-01 Label for Fuse Value (F1) 037641-01 Label for Fuse Values (F2-F6)
“This is the only plug provided on the North American power supply.
3-36
Millipede™ Troubleshooting
Millipede™ Troubleshooting with the CAT Box
Troubleshooting with the Read/Write Table 1 Address Lines
Controller Logic State Logic State
| For | 1C-Pin | For |
A. CAT Box Preliminary Set-Up Address AAAA Address 5555
- Remove the electrical power from the game and the
| CAT Box. | 1 | 20-25 | 0 | |
| 2. | Remove the game PCB from the game cabinet. | 0 | 1B-13 | 1 |
| 1 | 1B-14 | 0 | ||
| 3. | Remove Microprocessor 2C from the game PCB. | 0 | 1C/D-16 | 1 |
| 4. | Connect the harness from the game to the game PCB. | 1 | 1C/D-7 | 0 |
| 5. | Connect together the 0 and 42 test points on the | 0 | 1C/D-9 | 1 |
| game PCB with the shortest possible jumper. | 1 | 1C/D-5, | 0 |
6. Connect the WDDIS test point to ground. 0 eee 1
| 7. | Connect ihe CAT Box flex cable to the game PCB edge | } | pe. | : |
| test connector. | 1 | 1DiE-7 | 0 | |
| 8. | Apply power to the game and to the CAT Box. | 0 | ADIE-9 | 1 |
| 9. | Set CAT Box switches as indicated: | 1 | 1D/E-18 | 0 |
| a. | TESTER SELF-TEST: OFF | 0 | 1D/E-14 | 1 |
| b. | TESTER MODE: R/W | 1 | 1DIE-12 | 0 |
| ie) | AD/E-16 | 1: |
- Press TESTER RESET.
- Connect the DATA PROBE to the CAT Box. Connect the DATA PROBE ground clip to a game PCB ground test point.
B. Checking the Address Lines Perform the CAT Box preliminary set-up.
- Set CAT Box switches as indicated: a. BYTES: 1 b: PULSE MODE: UNLATCHED c. RIW MODE: (OFF) d. R/W: READ
- Key in the address pattern given in Table 1 (use AAAA to start) with the CAT Box keyboard. 4, Set R/W MODE to STATIC.
- Probe the IC-pin with the DATA PROBE and check that the 1 or 0 LED indicated in Table 1 lights up. Repeat this step for each address line listed in Table 1.
- Repeat parts 2-c through 5 using address 5555.
Troubleshooting
po
aap
al . Checking the Data Lines Perform the CAT Box preliminary set-up. Set CAT Box switches as indicated: a. BYTES:1 b. R/W MODE: (OFF) c. RAW: WRITE Key in address 0000 with the keyboard. Press DATA SET. Key in data AA with the keyboard. Set R/W MODE to STATIC. Probe the IC-pin with the DATA PROBE and check that the 1 or 0 LED indicated in Table 2 lights up. Repeat this check for each IC-pin in Table 2. Set RW MODE to (OFF). Repeat parts 4 through 6 using data 55 in part 4.
Table 2 Data Lines
Logic State Logic State
For IC-Pin For
Data AA Data 55
| q | 4E-18 | 0 |
| te) | 46-17 | 1 |
| 1 | 4E-16 | t) |
| 0 | 4E-15 | 1 |
| 1 | 4-14 | 0 |
| Q | 4EA3 | 1 |
| 1 | 4E-12 | 0 |
| 0 | 4E-11 | 1 |
| 1 | 4E-2 | 0° |
| 0 | 4E-3 | 1 |
| 1 | 4E4 | 0 |
| 0 | 4E5 | 1 |
| 1 | 4E6 | 0 |
| t) | 4E-7 | 1 |
| 1 | 4E8 | Q |
| 0 | 4E-9 | 1 |
Millipede™
D. Checking the RAM 1. 2. Perform the CAT Box preliminary set-up. Set CAT Box switches as indicated: a. DBUS SOURCE: ADDR b. BYTES:1024 c. R/W MODE: (OFF) d. R/W: WRITE Enter address 0000 with the keyboard. Set the CAT Box switches as indicated: a. AW MODE to PULSE and back to (OFF) b. RiW to READ ¢. R/W MODE to PULSE and back to (OFF) It the CAT Box reads an address that doesn’t compare with that written, the COMPARE ERROR LED will light up. The ADDRESS/SIGNATURE display of the CAT Box will show the failing address location and the ER- ROR DATA DISPLAY switch is enabled. Using this switch, determine if the error is in the high-order or low-order RAM. Repeat this test with DBUS SOURCE set to ADDR. Set the CAT Box switches as indicated: a. BYTES: 256 b. DBUS SOURCE. ADDR c. R/W MODE: (OFF) d. RW: WRITE Repeat parts 5 through 6 using addresses 1000, 1100, 1200, and 1300.
Millipede™
£. Checking the Custom Audlo I/O Chips
- Perform the self-test. ¢ Substitute a known good part for a suspected defective part. © Use the following procedure.
Perform the CAT Box preliminary set-up. Set CAT Box switches as indicated: a, BYTES: 1 b. RIW: WRITE c. R/W MODE: (OFF) Enter the address from Table 3 with the keyboard. Press DATA SET and enter the data from Table 3 with the keyboard, Set R/W MODE to PULSE and back to (OFF). Repeat parts 3 through 5 for each address and data listed in Table 3. Check for the response indicated. Troubleshooting
Table 3 Custom Audio I/O Chips
Address
0402 0403
O80F O80F
0801
0801
0802 Data
AF
zB
2888 8
AF Test Results
Custom Audio VO Chip 4D channel 1 produces pure tone. Custom Audio I/O Chip 4D channel 1 turns off.
Custom Audio !/O0 Chip 4D channel 2 produces pure tone. Custom Audio I/O Chip 4D channel 2 turns off.
Custom Audio I/O Chip 4B channel 1 produces pure tone. Custom Audio I/O Chip 4B channel 1 off.
Custom Audio 1/0 Chip 4B channel 2 produces pure tone. Custom Audio 1/O Chip 4B channel 2 off.
Troubleshooting
F. Checking the Player Switch, Option Switch, and Trak-Ball™ inputs Perform the CAT Box preliminary set-up.
a a c. Enter address 2505 with the keyboard. Set CAT Box switches as indicated: a : b. BYTES: 1 R/W: WRITE RiW MODE: (OFF)
Press DATA SET and enter data 00 with the keyboard. Set R/W MODE to PULSE and back to (OFF). For each entry listed in Table 4, do the following: eogp
rza>o
zo Set R/W MODE to (OFF). Set R/W to WRITE. Enter the first address with the keyboard. Press DATA SET and enter the data for that address with the keyboard. Set R/W MODE to PULSE and back to (OFF). Set RIW to READ. Enter the next address. Set RIW MODE to STATIC. Activate the input switch or signal indicated in Table 4 and check the test result. Set R/W MODE to (OFF). Repeat parts g through j for each subsequent address given for the entry.
Table 4 Player Switches, Option Switches, and Trak-Ball™ Inputs
| Entry | Address | Data | input Switch/Signals | Test Results |
| 1 | 2507 | 00 | ||
| 2000 | Option Switch 0 Toggles 1-4, | DATA display changes when |
Trak-Ball™ 1 HDIR, FIRE1, any of these switches or VBLANK, START1 signals is activated.
2001 Option Switch 0 Toggles 5-8, Trak-Ball™ 1 VDIR, FIRE2, START2
2010 Left Coin Switch, Right Coin Switch, Auxillary Coin Switch, SLAM 2011 Self-Test Switch, CABINET
| 2 | 2605 | FF |
| 2000 | Trak-Ball™ 1 HCOUNT and | DATA display changes when |
HDIR, VBLANK, START1, any of these switches or FIRE1 signals is activated. 2001 Trak-Ball™ 1 VCOUNT and VOIR, START2, FIRE2
| 3 | 2507 | FF |
| 2000 | Trak-Ball™ 2 HCOUNT and | DATA display changes when |
HDIR, VBLANK, START1, any of these switches or FIRE1 signals is activated. 2001 Trak-Ball™ 2 VCOUNT and VDIR, START2, FIRE2 Millipede™
Millipede™
G. Checking the LED, Coin Counter, and Video Rotate Outputs
- Perform the CAT Box preliminary set-up.
- Set CAT Box switches as indicated: a. DBUS SOURCE: DATA b. BYTES: 1 c. RIW: WRITE d. R/W MODE: (OFF)
- Enter the address in Table 5 with the keyboard.
If you write ON data to activate a solenoid, deactivate the solenoid immediately by writing the OFF data. If you leave a solenoid activated for more than 10 seconds, you may have to replace the solenoid and/or its driver, due to overheating.
- For each address listed in Table 5, do the following: a. To activate the output: © Press DATA SET.
- Enter the ON data with the keyboard. Set RIW MODE to STATIC and back to (OFF). b. To deactivate the output:
- Press DATA SET. » Enter the OFF data with the keyboard.
- Set RW MODE to STATIC and back to (OFF).
Table 5 LED and Coin Counter Outputs
Address On Off Output Device
Data Data
| 2501 | FF | 00 | Left Coin Counter |
| 2502 | FF | 00 | Right Coin Counter |
| 2503 | 00 | FF | Player 1 LED |
| 2504 | 00 | FF | Player 2 LED |
| 2506 | FF | 00 | VIDROT |
Troubleshooting
Troubleshooting with Signature
Analysis
A. Checking the Address Bus
- Perform the CAT Box preliminary set-up.
- Connect the three BNC-to-EZ clip cables supplied with the CAT Box to the SIGNATURE ANALYSIS CONTROL START, STOP, and CLOCK jacks of the CAT Box.
- Connect the three black EZ clips to a game PCB ground test point. 4, Set the CAT Box switches as indicated: TESTER MODE: SIG TESTER SELF-TEST: OFF PULSE MODE: LATCHED START: Negative-going edge trigger STOP: Negative-going edge trigger CLOCK: Negative-going edge trigger
- Press TESTER RESET on the CAT Box.
- Connect the CAT Box Signature Analysis probe tips as indicated: a. START: Pin 25 of Microprocessor 2C b. STOP: Pin 25 of Microprocessor 2C. c. CLOCK: 02 test point
- Verify the set-up connections by connecting the DATA PROBE to a game PCB ground test point. The CAT Box ADDRESS/SIGNATURE display should show 0000. Now connect the DATA PROBE to a +5V test point. The ADDRESS/SIGNATURE display should show 0001.
- Probe the IC-pin listed in Table 6 with the DATA PROBE and check for the signature indicated. Repeat this check for each IC-pin listed. meaogp
Troubleshooting
Table 6 Address Bus Signatures
IC-Pin Signal Name Signature
| 1DIE-16 | ABO | uuu |
| 1DIEN2 | ABI | 5555 |
| 1DIE-14 | AB2 | cccc |
| 1D/E-18 | AB3 | 7F7F |
| 1DIEQ | ABA | 5H21 |
| 1D/E-7 | ABS | OAFA |
| AD/E-3 | AB6 | UPFH |
| 1DIES | AB7 | 52F8 |
| 1C/D-3 | ABS | HC89 |
| 1C/D-5 | AB | 2H70 |
| 1C/D-9 | AB10 | HPPO |
| 1C/D-7 | ABII | 1293 |
| 1C/D-16 | ABI2 | HAP7 |
| 1B-14 | A3 | 396 |
| 1B-13 | At4 | 3827 |
| 2C-25 | Ais | 755U |
. Checking the Address Decoders Perform A. Checking the Address Bus. Probe the IC-pin listed in Table 7 with the DATA PROBE and check for the signature indicated. Repeat this check for each IC-pin listed.
Table 7 Decoder Signatures
IC-PIN Signal Name Signature
| 1B-1 | MOS | 822A |
| 1B2 | SCRAM | A169 |
| 1B-3 | ie} | C5U3 |
1B5 ROM1 ICFH
| 1B6 | ROM2 | 0319 |
| 1B-7 | ROMS | u6u2 |
| 1B-9 | ROM4 | 601 |
| 3E-4 | INPUTS | 72P5 |
| 3E5 | OUTPUTS | 062F |
| 3E:10 | TO! | HCC5 |
| 3E1 | ek | 9PPA |
3E12 ZRAM 9ACA
| 4F-3 | ROM | 96CO |
| 4H-9 | EAROMRD | 61F3 |
| 4H-11 | INi | 4696 |
| 4H-12 | INO | 4H6H |
Millipede™
Troubleshooting with Checksums
- Perform the CAT Box preliminay set-up.
- Set the CAT Box switches as indicated: a. BYTES: 256 b. DBUS SOURCE: DATA c. R/W MODE: OFF d. CHECKSUM SWITCH: ON
- Key in the address pattern given in Table 8 (use 4000 to start). 4, Set the RIW MODE switch to PULSE and then back to (OFF).
- Check the CAT Box ADDRESS/SIGNATURE display for the appropriate checksum.
- Repeat parts 3 through 5 for each address listed in Table 8.
Table 8 ROM Checksums
Address Checksum
8000 CE95 5000 1203 6000 7A4B 7000 176F
Troubleshooting the Watchdog Circuit
The Watchdog circuit will send continuous reset pulses to the microprocessor if a problem exists within the microprocessor circuit. If the self-test fails to run, it is a good practice to check the RESET line. RESET is a microprocessor input (pin 40). In a properly operating game, reset should occur during power-up or when the RESET test point is grounded. A pulsing RESET line indicates that something is causing the microprocessor to lose its place within the program. Typical causes are:
- Open or shorted address or data bus lines. Bad microprocessor chip. Bad bus buffers. Bad ROM. Bad RAM. Any bad input or output that causes an address or data line to be held in a constant high or low state. A pulsing RESET signal indicates a problem exists somewhere within the microprocessor circuitry. To aid in troubleshooting, the WDDIS test point can be connected to a ground tesi point to prevent resets. This will sometimes allow the Self-Test to be used to diagnose the failure during a RESET condition. Par on
(from Sheet 6A)
Color Output
i ead Ll Eas
sf u387 | (from Sheet 6A)
Ars
ace
Hemi
nerd
- MOCRCE
ere | Tse
Color Memory Address Selectors pt ANCRCE
(from Sheet 7A)
- Coin Counter & LED Output
; ewrausen eurp——a Sa \ioRoT Tseu ot Ro, aw I : a a as f 20 te aig vw ae, aun aus LEO! wap—__th nm Cet C3] se Sah SE RESET, i. Rus: +s
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.