The Adventures of Robby Roto
The Adventures of Robby Roto! (Dave Nutting Associates / Bally Midway, 1981) · Manual · 96 pages · 55 sections · original scan
JUNE, 1882 Game Nos. 530, 574, 576
Manual
NO. 574 MINI
NO. 576 COCKTAIL
MIDWAY MFG. CO.
10750 W. GRAND AVENUE FRANKLIN PARK, ILLINOIS 60131 USA NO. 530 UPRIGHT Phone: (312) 451-1360 Cable Address: MIDCO ‘Telex No.: 72-1596
FORM NO. 00530-00300-0000
ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.
UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
URE.
ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.
MIDWAY MFG. CO. Snuites You Jo Use ouR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER MIDWAY GAME YOU NOW HAVE ON LOCATION.
CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS. Continental U. $. 800-323-7182 Hlinois Only 1-800-942-0497
COPYRIGHT 1982 © BY MIDWAY MFG. CO. ALL RIGHTS RESERVED.
NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131
Printed In U.S.A.
TABLE OF CONTENTS DESCRIPTION PAGE
1 Introduction
u. Location and Setup .. Inspection .. Installation . Self-Test .... Game Volume Adjustment Control . Option Switch Settings
Il. Game Operation . Self-Test Mode. Attract Mode.. Ready to Play Mode Play Mode . Two Player Operation ....... 0. eee e ccc e cece eect ene nee nee eee e nee e een een ne ee en eeee 3-8
IV. Maintenance and Repair .............- 0. cece cece cence ener e nett eee eee ner eeeeenteee 4-1 Cleaning Fuse Replacement ... Opening the Control Panel .. Removal of Main Display Glass and T.V. Bezel . T.V. Monitor Replacement Printed Circuit Board Replacement. Opening the Attraction Panel 4-11
Vv. Illustrated Parts Breakdown Commercial Card Rack Assy. Commerical Card Rack Assy. — Parts List. No. 530 — Robby Roto — Upright — Front .. No. 530 — Robby Roto — Upright — Front — Parts List. No. 530 — Robby Roto — Upright — Service Door & Utility Shelf Assy. No. 530 — Robby Roto — Upright — Service Door & Utility Shelf Assy. — Parts List No. 530 — Robby Roto — Upright — Rear Access .. No. 530 — Robby Roto — Upright — Rear Access — Parts List . No. 574 — Robby Roto — Mini — Front No. 574 — Robby Roto — Mini — Front — Parts List... No. 574 — Robby Roto — Mini — Rear Access : No. 574 — Robby Roto — Mini — Rear Access — Parts List . No. 576 — Robby Roto — Cocktail — Front ............ No. 576 — Robby Roto — Cocktail — Front — Parts List No. 576 — Robby Roto — Cocktail — Interior Access ... No. 576 — Robby Roto — Cocktail — Interior Access — Parts List.. No. 530 — Robby Roto — Upright — Header Fluorescent Assy...............+5 No. 530 — Robby Roto — Upright — Header Fluorescent Assy. — Parts List . Control Assy. — All Versions .. Control Assy. — Ail Versions — Parts List . Front Door Assy. — U.S.A. 25¢ Front Door Assy. — U.S.A. 25¢ — Parts List ......... 0 cect cece erence nee n eee eeeenes
TABLE OF CONTENTS
DESCRIPTION PAGE
vi.
vil.
Vill. Technical Troubleshooting . Introduction 6-1
«6-1 General Suggestions Harness Component Troubleshooting 6-1 Transformer and Line Voltage Problems . 2 A Glossary of Microprocessor Terms. Introduction to the Z80 CPU... General Purpose Registers .. Arithmetic and Logic Unit (ALU) .. Instruction Register and CPU Control . Z80 CPU Pin Description ........... MCR 11 System P.C. Board Jumper Options .
Coin Door Maintenance Metal Coin Acceptor Mechanisms Plastic Coin Acceptor Mechanisms.
T.V. Monitor Manual .... 2.2.0... 0.5 c ccc ect een ene nnenn tenn ete t ete n eens 8-1 Introduction 8-1 Symptom Diagnosis Guide to Schematic Symbols .. Troubleshooting ... Theory of Operation. . Differences Between Monitors . Parts Interchangeability ....... Wells-Gardner Monitor Schematic — 19" .... Wells-Gardner Monitor Replacement Parts List ... Electrohome Monitor Schematic — 19” Electrohome Monitor Replacement Parts List — 19' Electrohome Monitor Schematic — 13”.. Electrohome Monitor Replacement Parts List 8-10 + 8-11 ++ 8-13 8-14 -8-18
- 8-19
Schematics and Wiring Diagrams Wiring Diagram — Upright... Wiring Diagram — Mini.... Wiring Diagram — Cocktail Power Supply P.C.B. — Component Layout.. Power Supply P.C.B. — Schematic .. Ram Board — Component Layout Ram Board — Schematic .. CPU Board — Component Layout CPU Board — Schematic Memory Board — Component Layout ... Memory Board — Schematic.......... Audio Amp Board — Component Layout Audio Amp Board — Schematic ........ RGB Interface Board — Component Layout RGB Interface Board — Schematic.... Pattern Board — Component Layout .. Pattern Board — Schematic Game Board — Component Layout . Game Board — Schematic.
FIGURE PAGE
1-1 Assigned Point Values. . 2-1 Removal of Shipping Brkts — Upright 2-2 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assys . 2-2 2-3. Major Sub-Assys (Cont from Fig. 2-2) .. 2-4 Interlock Switch Operation 2-5 Location of Volume Control .. 2-6 Option Switch Settings ... 2-7 Option Switch Locations . 3-1 Identification of “On Screen” Graphics During Play 3-2 Self-Test — ROM/RAM .........0..0ceeeeeeneenene 3-2 3-3. Self-Test — Player Input.... 3-3 3-4. Self-Test — Set Up Options. 4-1 Location of Fuses ........ 4-2 Opening the Control Panel — Upright & Mini 4-3. Opening the Cocktail Game 4-4 Removing the Control Panel — Cocktail .. 4-5 Removing the Main Display Glass & T.V. Bezel — Upright ... 4-6 Removing the Main Display Glass & T.V. Bezel — Mini 4-7 Removing the Top Glass & T.V. Bezel — Cocktail 4-8 Removing the Monitor — Upright 4-9 Removing the Monitor — Mini . 4-10 Opening the Cocktail Game ..... 4-11 Removing the Monitor — Cocktail ........ 4-12 Opening the Front Access Door — Upright 4-13 Removing Printed Circuit Boards — Upright... 4-14 Removing Printed Circuit Boards — Mini .. 4-15 Removing Printed Circuit Boards — Cocktail 4-16 Opening the Attraction Panel — Upright ...... 417 Replacing the Fluorescent Tube Starter — Upright . 4-18 Opening the Attraction Panel — Mini 7-1 Removing and Replacing the Coin Acceptor . a 7-2 Cleaning the Metal Coin Acceptor . ..7-2 7-3 Lubricating the Metal Coin Acceptor . 7-2 7-4 Opening the Plastic Coin Acceptor... 7-3 7-5 Changing the Plastic Acceptor to Accept American or Canadian Quarters... TABLE OF FIGURES
IMPORTANT NOTE
DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and II of this manual completely. It will not take more than a few minutes and it may be very helpful.
I. Introduction
ROTO is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCKTAIL TABLE”. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to guide ROTO to the stolen treasures and the captured hostages while avoiding VOLTAR and his co-conspirators. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn. When playing this game, YOU are ROTO’s mentor. He takes his directions ONLY from YOU and will do your bidding exclusively. YOU determine the strategies he will use to defeat the evil monster VOLTAR who has invaded the Earth, stealing all types of treasures and burying them deep within the earth. VOLTAR also takes hostages and seals them in vaults deep within the earth. There is only one way to save the hostages and recover the stolen treasures. We must sendin ROTO. He will follow VOLTAR right into his own home tunnels to rescue the hostages and recover the stolen treasures VOLTAR has salted away.
To say the least, this makes VOLTAR more than just a little bit upset with ROTO. To help protect his stolen treasures and kidnapped hostages, VOLTAR has developed a breed of giant SPIDER that can sense ROTO's location and that can also travel through solid earth. These SPIDERS attempt to corner and capture ROTO. And to direct their hunt for ROTO, VOLTAR turns himself into a TROLL that can travel through solid earth. lf and when ROTO is captured by the SPIDERS or the TROLL, he is forcibly ejected from VOLTAR’s tunnels and you loose one player. As your skill level increases and you get into the higher racks of the game, the ability of the SPIDERS and the TROLL to sense ROTO’s location increases. This makes ROTO's chances of survival considerably smaller. And VOLTAR, being what he is, has reinforcements in the form of a set of disembodied TEETH that he can call on to help him track ROTO. down and put the bite on him. These TEETH also have the ability to travel through solid earth. ROTO has no reinforcements he can call on to help him defend himself against his enemies. He has ONLY YOUR SKILL at maneuvering and forming strategies plus one use of the MAGIC button (which makes ROTO and any hostages he has with him invisible to all monsters for a short period of time) per rack to keep him safe as he carries out his rescue missions. Bonus ROTOs are awarded to you periodically throughout the game: after you complete every third rack of the game. Each recaptured treasure and rescued hostage has an assigned point value as listed in Figure 1-1. In the “2 times” and “3 times” racks, the values of all items are doubled or tripled respectively.
Major Features
Your ROTO game has several outstanding features among which is the fact that: 1) A bonus ROTO is awarded to each player after every third rack completed; 2) The award of these bonus ROTOs is NOT tied to any scoring ability of the player (alow scoring player can receive just as many bonus ROTOs as a high scoring one if he can survive as long as the other player. Surviveability is what the award of bonus ROTOs is tied to); 3) Your ROTO is allowed one use of the MAGIC button per rack of the game;
- If you do not use the MAGIC button in any particular rack, you are allowed to accumulate your unused MAGICs; 5) When you do use the MAGIC. button, your ROTO and any hostages he has with him at that time will become invisible to all the monsters on the screen for approximately 5 to 7 seconds (He can go right through them and not be caught); 6) The Upright model is provided with a front slide out service shelf for ease of maintenance; and 7) All models are provided with a service outlet to aid the service technician and provide an electrical source for whatever purpose he may have in mind.
Game Objective
The object of the game is to HAVE FUN and survive as long as possible while constantly improving your skills, rescuing as many of the hostages as you can, and recapturing as much stolen treasure as possible. As you do this, each following maze will be harder and harder to complete.
POINT VALUE POINT VALUE EACH HOSTAGE
PICK UP - EACH TIME OUT OF DOOR 100 POINTS 200 POINTS 250 POINTS 300 POINTS ETC.
ALL TREASURE VALUES
2nd MAZE 3rd MAZE 4th MAZE 5th MAZE 6th MAZE & BEYOND
ALL ROOMS ENTERED VALUES 200 POINTS EA. 400 POINTS EA. 600 POINTS EA. 800 POINTS EA. 1000 POINTS EA. 300 POINTS 600 POINTS 750 POINTS 900 POINTS ETC. 200 POINTS 400 POINTS 500 POINTS 600 POINTS ETC.
400 POINTS EA. 800 POINTS EA. 1200 POINTS EA. 1600 POINTS EA. 2000 POINTS EA. 1200 POINTS EA. 1800 POINTS EA. 2400 POINTS EA. 3000 POINTS EA.
5 POINTS EA. 10 POINTS EA. 20 POINTS EA. 30 POINTS EA. 40 POINTS EA. 50 POINTS EA. 1st MAZE 2nd MAZE 3rd MAZE 4th MAZE 5th MAZE 6th MAZE & BEYOND
MAZE MULTIPLIER DETERMINATION
3 HOSTAGES TOGETHER 3 HOSTAGES TOGETHER 2 MAZES IN A ROW 20 POINTS EA. 40 POINTS EA. 60 POINTS EA. 80 POINTS EA. 100 POINTS EA. 60 POINTS EA. 90 POINTS EA. 120 POINTS EA. 150 POINTS EA.
Figure 1-1 Assigned Point Values
II Location and Setup
INSPECTION
1.
2.
6.
7. Remove the game from its shipping crate. Inspect the entire outside of it for any signs of damage. O Any scratches? dents? cracks? O Any broken controls? O Any broken glass or plastic? Just look it over closely and make a note of any signs of damage. . Remove the shipping cleats from the bottom of the cabinet. © UPRIGHT MODEL ONLY: Remove the red shipping brackets shown in Figure 2-1 which hold down the slide out utility shelf. See label on top of coin box cover. . Install the four levelers, one at each corner of the cabinet. O Level the cabinet. . Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-2. C Also check to make sure all plug-in connectors on the wire harness are firmly seated.
- Location requirements:
ny O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative O Space required: Upright 25" x 32” (64 x 82 cm) Mini 20" x 29" (51 x 74 cm) Cocktail 32” x 22” (82 x 56 cm) O Game height: Upright 72" (183 cm) Mini 60" (153 cm) Cocktail 29" (74 cm)
. Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value.
v4 RED SHIPPING BRKTS (2) MUST BE REMOVED BEFORE SHELF CAN SLIDE OUT
Figure 2-1 Removal of Shipping Brkts — Upright
SERIAL NUMBER
POWER SUPPLY
TRANSFORMER BOARD ASSY. (NOT SEEN)
SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)
TRANSFORMER BOARD ASSY.
CONTROL PANEL (PLAYER 1)
LOGIC BOARDS, (CARD RACK)
INTERLOCK SWITCH: (INSIDE DOOR) SERIAL ON/OFF
NUMBER: SWITCH
T.V, MONITOR INTERLOCK SWITCH
INTERLOCK ‘SWITCH
LOGIC BOARDS ie (CARD RACK) ‘ i . POWER SUPPLY P.C.B. LOGIC BOARDS (CARD RACK)
ON/OFF SWITCH E ‘TRANSFORMER BOARD ASSY. (NOT SEEN)
UPRIGHT
POWER SUPPLY
(PLAYER 2)
ON/OFF SWITCH UNDER TABLE ON PLAYER 2 SIDE
COCKTAIL
Figure 2-2 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assys
If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game. . Interlock and power ON/OFF switches. See Figure 2-2. 0 To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models). When any access door is opened, the interlock switch installed there turns off all power to the game. © Check each operation. Qa
interlock switch for proper
After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem
CONTROL PANEL
INTERLOCK SWITCH BEHIND DOOR from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 2-2. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON" position. \f the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS [8 TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-4.
CONTROL PANEL
Figure 2-3 Major Sub-Assys (cont. from Fig. 2-2)
Figure 2-4 Interlock Switch Operation SELF-TEST Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).
GAME VOLUME ADJUSTMENT CON- TROL. (See Figure 2-5.) The game volume control pots are located on a panel: Upright model — mounted on the monitor skirt behind the coin box; Mini and Cocktail Table models — inside coin door mounted to right side of cabinet as you face coin door. For adjustment, they may be reached through the coin door on ALL models. To make the sounds louder, turn the pots clockwise as you face them (7% ). To make the sounds less loud, turn the pots counterclockwise as you face them ( #— ).
VOLUME CONTROL
Figure 2-5 Location of Volume Control
2-4
OPTION SWITCH SETTINGS To change the most common option settings, you DO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- Test mode. The Self-Test switch is located on the bracket for the coin counter on the back side of the coin door closest to the door hinge. When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you must change one of the switches that is located on one of the game's P.C. boards, it is also recommended that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) The P.C. Board option switch settings, and what they will make the game do are shown in Figure 2-6. See Figure 2-7 for option switch locations.
“OFF” and then back “ON” again. This is be- ounce ee BOARD oS
cause the program ONLY reads the positions that 7” these option switches are set in on “POWER-UP”. Once you have turned the power on, you can move them all over the place and the game won't know it. Figure 2-7 Option Switch Locations
ROTO
OPTION SWITCH SETTINGS
LOCATED ON GAME BOARD
SW#1 SW#2 SW#3 SW#4 SW#5 SW#E SW#7 SW#8 NORMAL OPERATION OFF NOT NOT NOT NOT NOT FULL RESET ON USED USED USED USED USED
OPTIONS ADJUSTABLE FROM GAMES CONTROL PANEL TION SETTINGS ARE ADJUSTED DURING THE OPTIONS RETURN TO SELF-TEST MODE AND WILL BE COVERED IN DE- TAIL IN THE “GAME OPERATION” SECTION OF THIS FACTORY RECOMMENDED MANUAL. SETTINGS
NORMAL PLAY FREE PLAY THE REMAINDER OF ROTO’s MOST COMMON OP-
Figure 2-6 Option Switch Settings
2-5
Ill Game Operation
ROTO is a one or a two player game with acolor T.V. monitor. The game gives a display which has all the parts shown in Figure 3-1.
The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE/ INITIAL, and SELF-TEST.
SELF-TEST MODE The Self-Test mode is a special mode for checking the game switches and computer functions. It is the
easiest and best way to check for proper operation of
the entire game.
You may begin a Self-Test at any time by sliding the
Self-Test switch to the “ON” position after the power to the game is on (once this occurs, there is no way out of the Self-Test mode except to go through all the Test Displays). When this is done, the game will react as follows:
- In the First Test Display, you will see vertically striped curtains which go from the top of the screen to the bottom.
PLAYER 1 SCORE
- There is no Second Test Display unless there is a malfunction of the last RAM chip on the ROM/ RAM Board. SPECIAL NOTE: IF EITHER THE FIRST OR SECOND TEST DISPLAY IS BAD THIS WOULD MEAN THAT THE GAME IS NOT CAPABLE OF COMPLETING THE SELF-TEST ON ITSELF. THE BAD INDICATIONS YOU WOULD GET ARE AS FOLLOWS: O First Test Display: if bad, the monitor screen will lock up with alternating black and write DIAGONAL lines. This means that ihe test ROM (IN SOCKET X1) on the ROM/RAM Board is bad. O Second Test Display: if bad, the monitor screen will lock up with alternating red and black DIAGONAL lines. This means that the last RAM (IN SOCKET X24) on the ROM/RAM Board is bad. BOTH OF THE ABOVE CHIPS MUST BE GOOD IN ORDER FOR THE GAME TO BE ABLE TO CONDUCT A SELF-TEST ON ITSELF. IF BAD, REPLACE THEM ONLY WITH CORRESPOND- ING CHIPS AS CALLED OUT IN THE PARTS LIST OF THIS MANUAL.
- The Third Test Display looks like the following Figure 3-2.
PLAYER 2 SCORE RESERVE MAGICS
TREASURE ROTOS REMAINING
m> HOSTAGE
ROTO IN PLAY
Figure 3-1 Identification of “On Screen” Graphics During Play
Figure 3-2 Self-Test — ROM/RAM
If nothing is written out beside the numbers 1, 2,3, and 4, they are O.K. 5 is asound mode ONLY (for purposes of volume adjustment) and provides no diagnostic type information. 0 “1” checks the Screen RAM — If no good — “BAD” is written out beside this number.
O “2” checks the Write Protect RAM — If no good
- one or more of the following numbers is written out beside this number: 12345678. These numbers tell what is wrong with the Write Protect RAM test.
DISPLAY 1 = testram high did not zero festram low did not zero 3 = testram high did not set 4=testram low did not set 5 = testram high zeroed and should not have festram low zeroed and should not have 7 = scratch ram next to write protect did not set and should have 8 = scratch ram next to write protect did not zero and should have The meaning of the RAM tests is this: If Write Protect tests 1, 2, 3, and/or 4 fail, X21 should also fail. If Write Protect tests 5 or 6 fail, Write Protect is not enabled. If ONLY Write Protect test number 6 fails, Write Protect is not covering enough memory. If Write Protect tests 7 or 8 fail, Write Protect is covering too much memory — which should also show an X21 failure reading. O “3” checks the Scratch/Battery Back Up RAM
- If no good — one or more of the following numbers is written out beside this number: X21, X22, X23, or X24 — depending on which RAM is bad. These numbers tell which socket the bad RAM is in on the ROM/RAM board. 0 “4” checks ROMs “B, C, D, E, F, G, H, J, and K”
- If no good — Their respective letter(s) are written out beside this number. . Ifa bad ROM or RAM chip is found by the game’s internal check system during the Self-Test, the game indicates this to you by showing the location code of the bad chip(s) to the right of the check number. The following table translates the chip location codes into actual positions on the various P.C. Boards.
DESCRIPTION WHITE & BLACK DIAGONAL STRIPES ROM located on ROM/RAM board at position X1 is bad. RED & BLACK DIAGONAL STRIPES 1 BAD
2 12345678 3 X21, X22, X23, X24
4B 4c
4e 4F 4G 4H 4J 4k
3-2 RAM located on ROM/RAM board at position X14 is bad. CHECK BOTH RAM BOARDS FOR MALFUNCTIONING PART(S). RAM located on ROM/RAM board at position X21 is bad. CHECK RAMS AT INDICATED POSITIONS ON ROM/RAM BOARD. ROM located on ROM/RAM board at position X2 is bad. ROM located on ROM/RAM board at position X3 is bad. ROM located on ROM/RAM board at position X4 is bad. ROM located on ROM/RAM board at position X5 is bad. ROM located on ROM/RAM board at position X6 is bad. ROM located on ROM/RAM board at position X7 is bad. ROM located on ROM/RAM board at position X8 is bad. ROM located on ROM/RAM board at position X9 is bad. ROM located on ROM/RAM board at position X10 is bad.
0 “5” is a sound mode to enable the operator to adjust the game's sound levels. The game's program automatically sets the tones emitted at half volume at the beginning of this mode.
- You advance to the next Test Display by pressing the 1 and 2 Player Buttons at the SAME time.
- During the Player Input Test Display the game will give a display which looks like that shown in Figure 3-3.
THESE SWITCHES NOT USED
DISPLAY CHANGES FROM 1 TO 0 WHEN SWITCH IS ACTIVATED
Figure 3-3 Self-Test — Player Input
PLAYER 2 COCKTAIL MODELS
PLAYER CONTROLS
UPRIGHT & MINI & PLAYER 1 COCKTAIL MODELS
FIGURE 3-3b TEST SW #3 COIN SW #2 COIN SW #1 COIN SW 1 PLAYER SW 2 PLAYER SW
1110011
FIGURE 3-3a
f
00000100
SS8—THROUGH—SS1
OPTION SWITCH SETTINGS
FIGURE 3-3c
™ 0 In this category, each of the game's player operated controls — including the coin switches on the back side of the coin door and the option switches located on the Game Board — may be checked individually. A “1” means that that particular switch is in the open condition and a “0” means that that particular switch is in the closed condition.
You advance to the next Test Display by pressing the 1 and 2 Player Buttons at the SAME time.
During the Setup Options Test Display the game will give a display which looks like that shown in Figure 3-4 .
C In this category, all common game options may
be changed from the control console: coins per credit and difficulty level. O The Difficulty Level setting has a range of 1 to9 with 1 being the easiest and 9 being the most difficult. Three (3) is the factory recommended game setting. The value of the Difficulty Level may be increased by pushing forward on the control stick or decreased by pulling backward on the control stick. O Push the 1 and 2 Player Buttons at the SAME time to move between subdivisions of this category. Upon reaching the last subdivision, hesitation of about 2 seconds will cause the cursor to cycle back to the first category of the subdivisions (DIFFICULTY LEVEL). C The coins and Credits may be adjusted respectively by pushing the One Player Button to select the left hand figure (coins) and then pushing forward on the control stick to increase this figure or pulling backward on the control stick to decrease the figure. By pushing the Two Player Button to select the right hand figure (credits), you may adjust it in the same manner as stated above. 0 Push the 1 and 2 Player Buttons at the SAME time to select the last subdivision in this category and then QUICKLY press them both again to advance to the next Test Display.
The next Test Display is a cross hatch pattern which can be used for various alignment procedures. This pattern will stay on the monitor screen until you advance to the next Test Display.
- You advance to the next Test Display by pressing the 1 and 2 Player Buttons at the SAME time. . The next, and last, Test Display is a color bar display showing Green, Red, Blue, and Yellow on the left side of the monitor screen and Black, Dark Gray, Light Gray, and White on the right side of the monitor screen.
3-4 1 DIFF 3 O CO/CR DOOR! 1 / 1 0 / 1 CO/CR DOOR2 1
Figure 3-4 Self-Test — Setup Options
O Again, this pattern will remain on the monitor screen until you press both the 1 and 2 Player Buttons at the same time. O If you have turned the Self-Test switch to the “OFF” position before pressing the 1 and 2 Player Buttons, normal game functions will return to the monitor screen. 0 If you HAVE NOT turned the Self-Test switch to the “OFF” position before pressing the 1 and 2 Player Buttons, normal game functions WILL NOT return to the monitor screen. The game will return to the First Test Display.
ATTRACT MODE
- The Attract mode starts:
O Just after power has been turned on to the game when there are no credits in its memory. (Self-Test switch is in the “OFF” position.) O After a Self-Test has been completed, no game was in progress, and no credits are left in game's memory. (Performing a Self-Test WILL NOT set the credits in the game’s memory to zero “O”.) O After the High Score/Initial mode when there are no more credits left in its memory. O in the Attract mode, the game will give the following displays centered on the monitor screen:
BALLY/MBWAY MFC. CB. BLY PRESENTS 115
1 JRY
IMSERT com
3-5
C1 No matter where the game is in the Attract Mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will hold this display on the monitor screen until the “1 PLAYER” or the “2 PLAYER" start button is pushed.
PRESS 1 PLAYER BUTTON oR DEPOSIT COWS FOR 2 PLAYER Gamer
>< MAGIC ROTO
PRESS 1 PLAYER BUTTON oR PRESS 2 PLAYER BUTTOR
READY TO PLAY MODE 1. The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game. . The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed. O After the coins have been accepted by the game, the “1 PLAYER” and/or “2 PLAYER” buttons will start flashing according to whether or not you have bought enough credits for a one or a two player game. . In the Ready-To-Play mode, the game will give the above display centered on the monitor screen. The credit sign tells you EXACTLY how many credits you have purchased. . If no START button is pressed, the game will hold the above display on the screen indefinitely.
PLAY MODE
1. The Play mode begins when either the “1 PLAYER” or the “2 PLAYER” start button is pressed. “PLAYER 1 UP” or “PLAYER 2 UP” is displayed centered on the screen ONLY when a2 player game has been selected. In a 1 player game, the screen says “GET READY” and play begins. . The Play mode ends when all of your ROTOs have been captured by VOLTAR. When this happens, “GAME OVER’ is written across the center of the monitor screen. . The game is made up of buried stolen treasures and imprisoned kidnapped hostages which it is ROBBY ROTOs mission to rescue. The evil VOL- TAR is the one responsible for all of this. When playing this game, YOU are ROBBY’s mentor. He takes his directions ONLY from YOU and will do your bidding exclusively. YOU determine the strategies he will use to defeat the evil monster VOLTAR who has invaded the Earth, stealing treasurers and kidnapping hostages. . There is only one way to save the hostages and recover the stolen treasures. We must send in ROBBY ROTO. He will follow VOLTAR right into his own home tunnels to rescue the hostages and recover the stolen treasures VOLTAR has salted away. . The player begins each game with3 ROTOs and 1 Magic. Reserve Magics are symbolized by “Ghost ROTOs” behind your regular reserve ROTOs. The Magic will make ROBBY ROTO and any hostages with him invisible to VOLTAR and all his creatures. it also makes ROBBY able to move faster. If you do not use your Magic in this rack, it will accumulate to the next rack. You get 1 Magic at the beginning of each rack. When used, they will last for 5
3-6 seconds, the game makes a special magical sound, the screen flashes, and ROTO becomes a ghost image of his former self.
- A bonus ROTO is awarded to the player after the completion of every third rack (3rd, 6th, 9th, 12th, 15th, 18th, and so on). The award of these bonus ROTOs is in NO way related to the level of a player's score. You MUST SURVIVE long enough to make it to the ends of these particular racks to collect your bonus ROTOs. There are 3 different “BONUS ROTO MACHINES”.
- There are 30 DIFFERENT mazes in the game divided into categories as follows:
CATEGORY NUMBER OF MAZES BEGINNERS ........-.0.-ee eee eeeeee 2 MEDIUM ...
Generally speaking, a player should never get the same maze twice in any game until he has gone through all 25 of the “HARD” mazes. After the 2nd rack, all future racks are in the “HARD” category.
ROBBY ROTO enters all mazes through the door at the top center of the monitor screen. When he is in the mazes, ROBBY can only dig in the directions of the pointing arrows at each room (tunnel junction point). He can move freely about any of the tunnels that have been dug out.
- GAME PARTICIPANTS — THEIR SIDE:
The evil monster VOLTAR has invaded the Earth, stealing all types of treasures and burying them deep within the earth. VOLTAR also takes hostages and seals them in vaults. To help protect his stolen treasures and kidnapped hostages, VOL- TAR has developed a breed of giant SPIDER that can sense ROTO’s location and that can also travel through solid earth. These SPIDERS attempt to corner and capture ROTO. And to direct their hunt for ROTO, VOLTAR turns himself into a TROLL that can travel through solid earth.
|f and when ROTO is captured by the SPIDERS or the TROLL, he is forcibly ejected from VOLTAR's tunnels and you lose one player. As your skill level increases and you get into the higher racks of the game, the ability of the SPIDERS and the TROLL to sense ROTO's location increases. This makes ROTO’s chances of survival considerably smaller. And VOLTAR, being what he is, has reinforcements in the form of a set of disembodied TEETH that he can call on to help him track ROTO down and put the bite on him. These TEETH also have the ability to travel through solid earth.
- GAME PARTICIPANTS — YOUR SIDE: ROTO has no reinforcements he can call on to heip him defend himself against his enemies. He has ONLY YOUR SKILL at maneuvering and forming strategies plus one use of the MAGIC button (which makes ROTO and any hostages he has with him invisible to ali monsters for a short period of time} per rack to keep him safe as he carries out his rescue missions.
- GAME PLAY: ROTO always enters the maze through the door at the top center of the monitor screen. His primary mission is to save as many hostages at one time as he can while keeping an eye out for buried treasures to recover along the way. lf ROBBY touches, or is touched by, any creature, that creature holds him down until VOLTAR can get there to carry him away and you lose one player.
If any of the hostages ROBBY ROTO is towing around with him are touched by any of the creatures (except the TEETH), he is immediately boxed in and carried off to some far away section of the screen. When the TEETH put the bite on any hostage, they DO NOT carry him off. The hostage stops and is sealed in while the TEETH continue on toward ROTO. This means that you can't “feed the TEETH a hostage” to get away from them as you can with ay ur the other creatures.
3-7 After this display, the game will go into the High Score/Initial mode and display the scores of the “BEST 21” players. If your score is not high enough to cause the game to add it to the list, the game will then either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).
- HIGH SCORE/INITIAL MODE:
In the High Score/Initial mode the game gives a display which looks like the following:
When in the High Score/Initial mode, your score is highlighted and there is one “A” and two blank spaces to the side of your score. By moving the control stick to the right, the letter can be made to seq ice forward through the alphabet: “A”, “B”, “ “‘D”, etc. By moving the control stick to the left, the letter can be made to st e backward through the alphabet: “Z”, “ “W", etc. When you reach your initial, release the control stick and push the MAGIC button. Your initial is frozen in place and a duplicate of that letter appears in the blank space next to your first initial. Select your next initial in the same manner as the previous one and so on. lf you do not wish to put your initials opposite your score, just press the MAGIC button three times. Three “A”’s will appear opposite your score. After the High Score/initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory) Most of the above holds true in the “2 PLAY- ER” mode also. But there are a few minor differences.
TWO PLAYER OPERATION
The Upright, Mini, and Cocktail Table models all have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.
- In the Upright and Mini models, the players must take turns at the controls.
- In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When it is not your turn, your set of controls will have NO effect on the game.)
- Your turn lasts until your ROTO is captured. At this point, the game will do one of several things depending on whether or not the captured ROTO was your last or if you still have others remaining in reserve.
ROTO CAPTURED — ROTOs REMAINING IN RESERVE
C Alt action stops. O Next, it displays “PLAYER ___ UP” and the maze changes to the one the other player is in. O Play begins for the other player.
ROTO CAPTURED — NO ROTOs REMAINING IN RESERVE
O Next, it displays “PLAYER ___ UP” and the maze changes to the one the other player is in. O Play begins for the other player. O After the last player's last ROTO is captured, the game displays “GAME OVER” for him too. O Atter this display, the game will go into the High Score/initial mode and display the scores of the “BEST 21” players. If neither of your scores is high enough to cause the game to add it to the list, the game will then either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory). However, if one or both of your scores was high enough to make you one of the “BEST 21” players, the game will add your score(s) to the list and allow you to enter your initials opposite your score. The number “1” and/or “2” is displayed to the side of each score to indicate which player made which score. O After you've entered your initials opposite your score(s), the game will then either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory). SLAM — OR — TILT SWITCH If activated, the SLAM — or — TILT SWITCH willend the game that was in progress and also remove one credit from any credit balance in the game’s memory at that time. This is the case in all models regardiess of whether it is a one or a two player game.
IV Maintenance and Repair
Your NEW game needs certain types of maintenance to keep it in-good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis. CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.
FUSE REPLACEMENT This game contains several fuses located as shown in Figure 4-1.
- UPRIGHT MODEL: As viewed from the front, facing the cabinet, with the utility shelf slid out through the game's front access door, the fuses are located: between the Main Power Transformer and the T.V. Isolation Transformer, just to the left of the Service Outlet, and on the Power Supply Board Assembly.
- MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Transformer and Power Supply Board Assemblies.
- COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Transformer and Power Supply Board Assemblies. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual. See the T.V. Monitor Manual (available on request from your distributor or the Monitor Manufacturer) and/or the T.V. Troubleshooting Section of this manual for information on these fuses.
UPRIGHT GAME SHOWN MINI AND COCKTAIL GAMES ARE SIMILAR
Figure 4-1 Location of Fuses
OPENING THE CONTROL PANEL (See Figure 4-2).
- UPRIGHT MODEL: O The control panel is held in place by three latches, one on the left side, one on the right side, and one on the front center. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. O To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed.
O To reinstall the control panel, reverse this procedure.
UPRIGHT
- MINI MODEL: O The control panel is heid in place by two latches, one on the right side and one on the left side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center of the control panel. Once they are released, unhook them from their latch plates. G To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. 0 To reinstall the control panel, reverse this procedure.
Figure 4-2 Opening the Control Panel — Upright & Mini
4-2
Figure 4-3 Opening the Cocktail Game
- COCKTAIL TABLE MODEL: O Each contro! panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 4-3.
Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-3.
EXTREME CARE MUST be taken when opening the cabinet.
Remove the screws which secure the control panel in place. See Figure 4-4. O To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed.
O To reinstall the control panel, reverse this procedure.
2 SCREWS (2 SIDES)
3 SCREWS
Figure 4-4 Removing the Control Panel — Cocktail
REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY
- UPRIGHT MODEL: (See Figure 4-5).
O Turn the power to the game off and remove the control panel. This frees the main-displayglass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. © Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed.
O To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure.
DISPLAY
GLASS CLAMPS
Figure 4-5 Removing the Main Display Glass & T.V. Bezel — Upright
- MINI MODEL: (See Figure 4-6).
DISPLAY GLASS
Figure 4-6 Removing the Main Display Glass & T.V. Bezel — Mini
- COCKTAIL TABLE MODEL: (See Figure 4-7).
TOP _ GLASS GLASS CLAMPS
T.V. BEZEL GLASS CLAMPS
Figure 4-7 Removing the Top Glass & T.V. Bezel
- Cocktail
T.V. MONITOR REPLACEMENT:
4-5
- UPRIGHT MODEL: (See Figure 4-8). O Turn power off to the game. DO Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet’s right and and left side. The monitor is removed by sliding it out the back of the cabinet. See Figure 4-8. O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test. Oo
- MINI MODEL: (See Figure 4-9). O Turn the power off to the game. O Open the rear access door. 0 Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Mini Model” procedure. O With the removal of only four nuts, the T.V. monitor will be loose.
O The monitor is removed by supporting it and pulling straight back as shown in Figure 4-9. O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.
REMOVE (4) REMOVE (4) BOLTS BOLTS
pueene
Figure 4-8 Removing the Monitor — Upright Figure 4-9 Removing the Monitor — Mini
CLAMPS
Figure 4-10 Opening the Cocktail Game
- COCKTAIL TABLE MODEL: (See Figure 4-11). O Turn power off to the game. O Open the coin box door and release the two latches indicated in Figure 4-10.
he right hand latch is very close to VOLTAGE the monitor.
O Once the latches are released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-10.
0 After replacing the T.V. monitor, be sure to run
the game Se!* 7. reverse this
REMOVE 6 SCREWS (3 EACH SIDE) AND LIFT MONITOR
SCREWS (2 EACH SIDE)
Figure 4-11 Removing the Monitor — Cocktail
PRINTED CIRCUIT BOARD O Mounted on the utility shelf is the commercial (P.C.B.) REPLACEMENT: card rack with six cards in it. O Mounted next to the commercial card rack is its power supply PCB. O To remove the cards from the commercial card rack, simply lift on their extractors and remove
- UPRIGHT MODEL: (See Figure 4-13). O To remove the power supply PCB for the CO Turn the power to the game off. commercial card rack. See Figure 4-13. Disconnect it from ail its cabling, remove the O Unlock and open the coin door. screws which secure the top PCB supportto its O Reach inside and release the game's front - mounting bracket (be careful not to lose the access door locking latches. See Figure 4-12 washers), and lift it out. and the drawing on top of the coin box lid. O To reinstall the above P.C.B.'s, reverse this O Slide out the utility shelf. See Figure 4-13. procedure.
OWA COIN BOX COVER i Yo ee a 3) Si ay Di \S777 EEE <4» COIN DOOR
FOR SERVICE ACCESS
OPEN LOWER SERVICE DOOR BY RELEASING
TWO ACCESS CLAMPS. (Locations aS SHOWN)
REMOVE TWO RED SHIPPING BRACKETS AND SLIDE OUT SERVICE SHELF. §M051- 00100-0000
Figure 4-12 Opening the Front Access Door — Upright
4-8
REM. /E THIS BRACKET TO TAKE OUT POWER SUPPLY BOARD
LiFT UP ON EXTRACTORS TO REMOVE CARDS FROM CARD RACK
Figure 4-13 Removing Printed Circuit Boards — Upright
- MINI MODEL: (See Figure 4-14). O Turn the power off to the game.
CO Unlock and open the rear access door.
O Disconnect the “GAME PCB” from all its cabling. 0 To remove any of the PCB's from the commercial card rack, just lift up on their extractors and slide them up and out. They may now be removed from the cabinet. O Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-14, and slide it out the back of the cabinet. 0 To reinstall the above P.C.B.’s, reverse this procedure.
- COCKTAIL TABLE MODEL: (See Figure 4-15). C Turn the power off to the game.
O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 4-10.
Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-10.
LIFT UP ON EXTRACTORS TO
- REMOVE CARDS FROM RACK oA panne
Figure 4-14 Removing Printed Circuit Boards — Mini
To remove the power supply board. See Figure Disconnect the “GAME PCB” from all its 4-15. cabling. Disconnect it from al! its cabling. To remove any of the PCB's from the commer- Remove the two smallest P.C.B. supports. cial card rack, just lift up on their extractors and Once these are removed, the power supply can slide them up and out. be lifted out the top of the cabinet. They may now be removed from the cabinet. To reinstall the power supply board, reverse To reinstall these PCB's, reverse this this procedure. procedure.
D To remove the PCB's from *he commercial card rack. See Figure 4-15.
REMOVE P.C.B. SUPPORT LOCATED ON THIS SIDE AND SLIDE BOARD UP
LIFT UP ON EXTRACTORS TO REMOVE CARDS FROM RACK
Figure 4-15 Removing Printed Circuit Boards — Cocktail
4-10
OPENING THE ATTRACTION PANEL:
- UPRIGHT MODEL: (See Figure 4-16). C Turn the power to the game off. O Opening the attraction panel: Remove the screws which secure the bottom bracket in place. (They are on its under side.) REMOVE (3) See Figure 4-16. SCREWS HOLDING BRKT. Remove the bottom bracket and let the attraction panel drop down. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstali the attraction panel. reverse this procedure. D The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
Cl Replacing the fluorescent tube starter. See Figure 4-17. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. —_ To replace the fluorescent light tube starter, Figure 4-16 Opening the Attraction Panel — reverse this procedure. Upright
r™ ¥%, TURN FLUORESCENT TO REPLACE TUBE STARTER
geuccer
Figure 4-17 Replacing the Fluorescent Tube Starter — Upright
4-11
O Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. O Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker.
- MINI MODEL: (See Figure 4-18). O Turn the power off to the game.
O Remove the screws from the top and bottom of the formed attraction panel. O Remove the formed attraction panel by pulling it straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board. O To service the light bulbs and their mounting board: Turn the power to the game back onso youcan see which bulbs are burnt out Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure. O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.
- THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL.
REMOVE SCREWS. FROM TOP BRKT.
Figure 4-18 Opening the Attraction Panel — Mini
4-12

This page is a drawing, shown as the original scan.
ROBBY ROTO — COMMERCIAL CARD RACK ASSEMBLY
ROBBY ROTO — COMMERCIAL CARD RACK ASSEMBLY — PARTS LIST
ORDER BY PART NUMBER ONLY
A789-00003-0100 P.C. RACK ASSY. — RIGHT A789-00004-0100 P.C. RACK ASSY. — LEFT A789-00005-0000 P.C. RACK ASSY. — BASE 0789-00100-0000 MTG. BRKT. SUPPORT (2 REQ'’D.) 0789-00106-0000 RACK STRAP (2 REQ'D.) 0017-00101-0099 #6 x 1/4 SLT. HEX HD. SCREW (11 REQ'D.) 0017-00104-0019 #6 FLAT WASHER (3 REQ’D.) A082-90006-B000 BACK PANEL P.C. ASSY. (MOTHER BOARD) A082-91356-C000 RAM BOARD ASSY. A082-91354-F000 CPU BOARD ASSY. A082-91355-C000 PATTERN TRANSFER BOARD ASSY. A084-91423-A530 MEMORY BOARD ASSY. A084-90708-A530 GAME LOGIC BOARD ASSY. 0017-00007-0153 P.C. BOARD SUPPORT (2 REQ'D.) (NOT SHOWN)
5-1
NO. 530 — ROBBY ROTO — UPRIGHT — FRONT
NO. 530— ROBBY ROTO — UPRIGHT — FRONT — PARTS LIST
PART NO.
0530-00900-00XF A595-00011-0000 0537-00903-0052 0530-00102-00XF 0017-00101-0138 0017-00009-0522 0017-00009-0393 0017-00003-0187 0017-00101-0127 0017-00103-0061 0508-00900-0000 0508-00903-0000 0508-00901-0000 0017-00101-0017 0530-00901 -OOXF 0508-00108-0000 0017-00101-0027 0530-00902-0000 A530-00006-0000 A530-00005-0000 0017-00101-0620 0017-00103-0061 0508-00115-0000 0961-00115-OOXF 0017-00009-0033 0550-00101-0100 0550-00101-0200 0555-00901-0000 0017-00101-0141 A595-00005-0000 A530-00015-0000 0017-00042-0257 0017-00032-0093 0017-00103-0054 0017-00032-0092 0929-00905-00XF 0017-00103-0089 0017-00104-0112 A090-00300-09BK A530-00017-0000 0090-00002-04BK 0017-00101-0121 0935-00906-0200 0017-00102-0048 0017-00103-0026 ORDER BY PART NUMBER ONLY
DESCRIPTION
HEADER DISPLAY PLEX! — 23” x 8-7/8" x 3/16" HEADER LIGHT ASSY. GLASS CHANNEL — 8-1/8" LG. (2 REQ'D.) HEADER RETAINER #8 x 5/8 TORX TAMPER PROOF PAN HD. SCREW (3 REQ'D.) LONG ARM KEY T-20 (FOR ABOVE SCREW) BLACK SPEAKER GRILLE W/SLOTS (2 REQ'D.) 6” x 9" SPEAKER 8 OHM, 9W. (2 REQ'D.) #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ'D.) #8-32 HEX NUT W/SEMS (8 REQ'D.) 19” T.V. BEZEL T.V. SMOKED PLEXI-GLASS — 17-3/8" x 13-1/4" x 1/8" PLEXI-GLASS CLIPS (4 REQ'D.) #6 x 1/2 SLT. HEX HD. BLK. SCREW (3 REQ’D.) MAIN VIEWING GLASS — 23” x 19-11/16" x 3/16" GLASS STOP BRKT. (CABINET REAR) #8 x 3/4 SLT. HEX HD. M.S. (3 REQ'D.) DECORATIVE CONTROL SHELF OVERLAY WELDED-CONTROL SHELF PLATE ASSY. CONTROL SHELF PLATE ASSY. W/OVERLAY #8-32 x 1/2 CARRIAGE BOLT (10 REQ'D.) #8-32 HEX NUT W/SEMS (10 REQ'’D.) CENTER CONTROL SHELF LOCK BRKT. STRIKE (2 REQ'D.) LATCH CLAMP ( 3 REQ'D.) CONTROL SHELF MTG. BRKT. — RIGHT CONTROL SHELF MTG. BRKT. — LEFT PLASTIC LOCATING PIN (4 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (18 REQ’D.) CONTROL ASSY. CONTROL SHELF CABLE ASSY. PUSH BUTTON ASSY. — YELLOW (2 REQ'’D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 5/8-11 PAL NUT (2 REQ'D.) SMALL LIGHTED PUSH BUTTON SWITCH (2 REQ’D.) SWITCH BEZEL (2 REQ'D.) 5/8-24 HEX NUT (2 REQ’D.) WASHER (2 REQ'D.) U.S.A. 25¢ DOUBLE COIN DOOR ASSY. COIN DOOR CABLE ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) KICK PLATE — 22-7/8" LG. 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)
5-3
NO. 530 — ROBBY ROTO — UPRIGHT — SERVICE DOOR & UTILITY SHELF ASSY.
5-4
NO. 530 — ROBBY ROTO — UPRIGHT — SERVICE DOOR & UTILITY SHELF ASSY.
NO. 530— ROBBY ROTO — UPRIGHT — SERVICE DOOR & UTILITY SHELF ASSY. — PARTS LIST ORDER BY PART NUMBER ONLY
0961-00904-0100 DOOR PULL — 22-7/8" LG. 0017-00009-0512 DOOR HINGE (2 REQ'D.) 0017-00101-0027 #8 x 3/4 SLT. HEX HD. SCR. (12 REQ'D.) 0961-001 15-00XF STRIKE (2 REQ’D.) 0017-00009-0033 LATCH CLAMP (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. M.S. (8 REQ’D.) A088-00015-0000 INTERLOCK SWITCH & BRKT. ASSY. 0961-00119-0100 UTILITY SHELF RAIL — RIGHT 0961-00119-0200 UTILITY SHELF RAIL — LEFT 0961-00117-0000 UTILITY SHELF STOP BRKT. 0961-00121-0000 SHELF STOP BRKT. 0961-00120-0000 CABINET STOP BRKT. (2 REQ'’D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. MLS. (36 REQ’D.) MT00-00087-0000 POWER TRANSFORMER 120/240V. MT00-00092-0000 TRANSFORMER 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0017-00101-0060 #8 x 7/16 SLT. HEX HD. SCR. (4 REQ’D.) 0720-00001-0300 3 POSITION FUSE CLIP ASSY. 0720-00001-0200 2 POSITION FUSE CLIP ASSY. 0017-00003-0004 SLO-BLO FUSE — 2A, 250V. 0017-00003-0002 SLO-BLO FUSE — 1/2A., 250V. (4 REQ’D.) 0961-00906-0000 FISHPAPER SHIELD — FUSE 0961-00905-0000 LARGE FISHPAPER SHIELD 3010-13106-0000 TERMINAL STRIP A151-00079-0000 115V. CONVENIENCE OUTLET ASSY. A508-00037-0000 2 LEAD TRANSFORMER BRD. FILTER ASSY. A082-90421-B000 POWER SUPPLY ASSY. A530-00023-0000 TOP BRKT. ASSY. A961-00049-0000 MOUNTING FRAME & SUPPORT BRKT. ASSY. 0017-00101-0015 #6 x 1/2 SLT. HEX HD. M.S. (15 REQ’D.) A530-00004-0000 CARD RACK ASSY. W/BOARDS (SEE SEPARATE PHOTOGRAPH) 3000-17246-0600 7” GROUND STRAP 3000-17246-0900 48" GROUND STRAP 3000-17246-0000 GROUND STRAP
NO. 530 — ROBBY ROTO — UPRIGHT — REAR ACCESS
NO. 530— ROBBY ROTO — UPRIGHT — REAR ACCESS — PARTS LIST
ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
1 A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY. 0894-00916-0000 PLASTIC PULL & VENT (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ'D.) 0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC HORIZONTAL MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR MONITOR RAIL (2 REQ’D.) PLASTIC LOCATING PIN (4 REQ’D.) 1/4-20 x 3/4 SQR. NECK BOLT (4 REQ'D.) 7/8" DISH WASHER (4 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ'D.) T.V. BEZEL MTG. BRKT. (2 REQ’D.) 19" T.V. BEZEL GLASS STOP BRKT. #6 x 1/2 SLT. HEX HD. SCR. (3 REQ'’D.) INTERLOCK SWITCH & BRKT. ASSY. (2 REQ'D.) COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ’D.) LARGE PLASTIC COIN BOX 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ’D.) 1/4-20 HEX NUT (4 REQ’D.) AUDIO AMP P.C. BRD. ASSY. AUDIO AMP & HEAT SINK BRKT. 1/2” SPACERS (4 REQ'D.) #6 x 3/8 SLT. HEX HD. SCR. (4 REQ’D.) #6-32 x 3/8 SLT. PAN HD. SCR. (2 REQ'D.) #6-32 HEX NUT (2 REQ'D.) CARD RACK W/BOARDS ASSY. UNIVERSAL POWER SUPPLY ASSY. LINE CORD — 16 FOOT LONG CASTER ASSY. (2 REQ'D.) WHEEL BRKT. (2 REQ'D.) PLASTIC WHEEL (2 REQ'D.) SHAFT (2 REQ’D.) 3/8” E-RING (2 REQ'D.) 0017-00003-0418
0636-00101-0000 0555-00901-0000 0017-00102-0006 0017-00104-0014 0017-00101-0141 0508-00106-0000 0508-00900-0000 0508-00108-0000 0017-00101-0017 A088-00015-0000 A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A084-90912-A530 0530-00101-0000 0017-00042-0286 0017-00101-0010 0017-00101-0774 0017-00103-0060 A530-00004-0000 A082-90421-B000 0017-00003-0064 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037
ADDITIONAL PARTS LIST
BACK DOOR LOCK ASSY. 5-5/8” SQR. VENT GRILLE (4 REQ’D.) — BACK DOOR HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. MASTER CABLE ASSY. VIDEO ADAPTOR CABLE ASSY. VIDEO SIGNAL CABLE ASSY. 36" GROUND STRAP — CONTROL SHELF 20” GROUND STRAP — CONTROL SHELF COIN BOX DIVIDER — OPTIONAL R-G-B INTERFACE BRD. ASSY. A151-00098-0000 0017-00009-0490 A530-00012-0000 A530-00013-0000 A530-00014-0000 A530-00018-0000 A530-00019-0000 3000-17246-1000 3000-17246-0700 0950-00103-0000 A082-91363-B000
5-7
NO. 574 — ROBBY ROTO — MINI — FRONT
5-8
NO. 574— ROBBY ROTO — MINI — FRONT — PARTS LIST
ORDER BY PART NUMBER ONLY
0574-00901-00XF HEADER DISPLAY PANEL 0537-00903-0060 GLASS CHANNEL — 4-1/2” LG. (2 REQ’D.) 0574-00100-00XF HEADER BRKT. RETAINER (2 REQ'D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (8 REQ'D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A574-00007-0000 INSERT DISPLAY ASSY. 0017-00031-0030 WEDGE BASE LIGHT SOCKET (5 REQ’D.) 0017-00003-0219 #194 LAMP — 14 V., .27A (5 REQ’D.) A574-00015-0000 INSERT DISPLAY CABLE ASSY. 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS (2 REQ'D.) 0017-00003-0187 6" x 9 SPEAKER — 8 OHM, 9W. (2 REQ’D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ'’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0574-00900-00XF MAIN VIEWING GLASS — 17-13/16" x 14-13/16" x 3/16" 0537-00903-0056 GLASS CHANNEL — 14-1/2” LG. (2 REQ'D.) A555-00016-0000 GLASS CLAMPING PLATE ASSY. 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (2 REQ'D.) 0931-00903-0000 TV. BEZEL A961-00026-0000 BEZEL MTG. BRKT. ASSY. (2 REQ’D.) A574-00014-0000 OVERLAY TO CONTROL PLATE ASSY. 0574-00101-0000 CONTROL SHELF PLATE 0574-00902-0000 DECORATIVE CONTROL SHELF OVERLAY 0017-00101-0620 #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0550-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0550-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 PLASTIC LOCATING PIN (4 REQ'D.) 0961-00115-O00XF STRIKE (2 REQ’D.) 0017-00009-0033 LATCH CLAMP (2 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) A595-00005-0000 CONTROL ASSEMBLY A574-00016-0000 CONTROL SHELF CABLE ASSY. 0017-00042-0256 PUSH BUTTON ASSY. — RED (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 0017-00103-0054 5/8-11 PAL NUT (2 REQ’D.) 0017-00032-0092 LIGHTED PUSH BUTTON SWITCH (2 REQ'D.) 0929-00905-00XF SWITCH BEZEL (2 REQ’D.) 0017-00104-0112 INTERNAL WASHER (2 REQ’D.) 0017-00103-0089 5/8-24 HEX NUT (2 REQ'D.) A090-00300-09BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A530-00017-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) 0935-00906-0400 KICK PLATE — 17-15/16" LG. 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)
5-9
NO. 574 — ROBBY ROTO — MINI — REAR ACCESS
NO. 574— ROBBY ROTO — MINI — REAR ACCESS — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0017-00003-0187 6" x 9" SPEAKER — 8 OHM, 9W (2 REQ’D.) 0017-00003-0340 ELECTROHOME — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) 0017-00003-0396 WELLS-GARDNER — 13” COLOR DUAL SYNC HORIZ. MTG. MONITOR A926-00012-00XF T.V. MTG. BRKT. ASSY. 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. M.S. (2 REQ'D.) 0555-00100-0000 MONITOR MTG. BRKT. (2 REQ’D.) 0017-00102-0066 1/4-20 x 3/4 UNSLOT HEX HD. BOLT (4 REQ’D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ’D.) A088-00015-0000 INTERLOCK SWITCH & BRKT. ASSY. A090-00300-09BK DOUBLE ENTRY COIN DOOR ASSY. A950-00004-0000 COIN BOX ASSY. A950-00006-0000 COIN BOX CRADLE ASSY. 0950-00105-0000 COIN BOX COVER 0950-00104-0000 COIN BOX HANDLE 0950-00101-0000 COIN DEFLECTOR (2 REQ’D.) 0950-00900-0000 LARGE PLASTIC COIN BOX 0950-00103-0000 COIN BOX DIVIDER — OPTIONAL 0017-00101-0142 1/4-20 x 1-3/8 RND. HD. BOLT (4 REQ'D.) 0017-00104-0014 7/8" DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ'D.) A082-90421-B000 POWER SUPPLY P.C. ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. — 12" LG. (2 REQ’D.) 0624-00902-0300 P.C. SUPPORT BRKT. — 2-1/2” LG. 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2" LG. 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (10 REQ’D.) 0017-00104-0037 #8 FLAT WASHER (10 REQ'’D.) A530-00004-0000 CARD RACK W/BOARDS ASSY. A574-00009-0000 TRANSFORMER BOARD ASSY. A088-00013-0000 ON/OFF SWITCH & BRKT. ASSY. 0017-00003-0064 16 FT. LINE CORD
ADDITIONAL PARTS LIST A151-00098-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILLE (4 REQ'’D.) A574-00010-0000 LOW VOLTAGE CABLE ASSY. A574-0001 1-0000 HIGH VOLTAGE CABLE ASSY. A574-00012-0000 MASTER CABLE ASSY. A574-00017-0000 VIDEO ADAPTOR CABLE ASSY. A574-00018-0000 VIDEO SIGNAL CABLE ASSY. 3010-03003-0000 GROUNDING CLIP A082-91363-B000 R-G-B INTERFACE BRD. ASSY. 4530-0001 1-0000 AUDIO BRD. & HEAT SINK MTG. BRKT. ASSY.
LNOU4 — TIVLHDOD — OLOY AGEOY — 925 "ON
NO. 576— ROBBY ROTO — COCKTAIL — FRONT — PARTS LIST ORDER BY PART NUMBER ONLY
0017-00009-0499 COVER GLASS — 32" x 22" x 1/4” 0576-00900-0000 DECORATIVE ARTWORK UNDERLAY 0775-00104-00XF | GLASS CLIPS (8 REQ’D.) 0017-00101-0117 #8 x 5/8 BLK. PHIL. TRS. HD. SCR. (16 REQ'D.) 0557-00900-0000 |__T.V. BEZEL 0508-00905-0000 | SMOKED T.V. PLEXI-GLASS — 17-3/8” x 13-1/4" x 1/8" 0508-00901-0000 PLEXI-GLASS CLIPS (4 REQ’D.) 0017-00101-0017 | #6 x 1/2 SLT. HEX HD. SCREW (4 REQ’D.) A576-00004-0100 | CONTROL SHELF ASSY. — PLYR. #1 A576-00004-0200 | CONTROL SHELF ASSY. — PLYR. #2 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS (4 REQ’D.) 0017-00003-0187 | 6” x 9" SPEAKER — 8 OHM, 9W. (2 REQ’D.) 0017-00101-0127 | #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ’D.) 0017-00101-0136 | #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (16 REQ’D.) A090-00300-07BK | U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A530-00017-0000 | COIN DOOR CABLE ASSY. 0090-00002-02BK | LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0017-00102-0048 | 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 0017-00103-0026 | 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)
5-13
SS3HDOV YOINSLNI — WVLNOOD — OLOY AGEOY — 925 ‘ON
NO. 576-— ROBBY ROTO — COCKTAIL — INTERIOR ACCESS — PARTS LIST
0017-00003-0428
A557-00004-00XF 0017-00101-0642 0017-00104-0031 0017-00103-0061 0017-00102-0002 0017-00102-0052 0017-00104-0014 0921-00107-00XF 0017-00101-0769 0017-00009-0033 0017-00101-0141 0017-00009-0514 0017-00101-0639 0017-00103-0061 0576-00100-00XF 0576-00901-0100 0576-00901-0200 0017-00101-0620 0017-00103-0061 0510-00101-00XF 0017-00101-0341 A595-00005-0000 A576-00005-0100 A576-00005-0200 0017-00042-0301 0017-00032-0093 0017-00103-0054 0017-00032-0092
0929-00905-00XF 0017-00104-0112 0017-00103-0089 0930-00104-0000 0017-00101-0025 0930-00904-0000 0017-00031-0044 0017-00003-0219 0017-00101-0555 A530-00004-0000 A576-00008-0000 A082-90421-B000 A082-91363-B000 A084-90912-A530 0530-00101-0000 0017-00042-0286 0017-00101-0010 0017-00101-0774 0017-00103-0087 ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
ELECTROHOME — 19” COLOR DUAL SYNC VERT. MTG. MONITOR MONITOR MTG. BRKT. ASSY. (2 REQ’D.) #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ’D.) #8 FLAT WASHER (4 REQ’D.) #3-32 HEX NUT W/SEMS (4 REQ’D.) 1/4-20 x 1/2 SLT. HEX HD. BOLT (4 REQ’D.) 1/4-20 x 1" UNSLOT. HEX FLAT HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (8 REQ'D.) STRIKE (2 REQ’D.) #10 x 3/4 SLT. HEX HD. M.S. (4 REQ’D.) LATCH CLAMP (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. SREW (4 REQ’D.) 2-1/2" HINGE (2 REQ'D.) #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ'D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) CONTROL PANEL (2 REQ’D.) DECORATIVE OVERLAY — PLAYER #1 DECORATIVE OVERLAY — PLAYER #2 #8-32 x 1/2 CARRIAGE BOLT (8 REQ'D.) #8-32 HEX NUT W/SEMS (8 REQ’D.) BOTTOM PAN (2 REQ'D.) #6 x 1/4 PHIL. TRS. HD. SCR. (10 REQ’D.) CONTROL ASSY. (2 REQ’D.) CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2 YELLOW PUSH BUTTON ASSY. (2 REQ’D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ’D.) 5/8-11 PAL NUT (2 REQ’D.) SMALL RED LIGHTED PUSH BUTTON SWITCH — PLAYER #1 PANEL ONLY (2 REQ’D.) SWITCH BEZEL (2 REQ’D.) WASHER (2 REQ’D.) 5/8-24 HEX NUT (2 REQ’D.) CONTROL PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2 SLT. HEX HD. M.S. (16 REQ’D.) LIGHT SHIELD (2 REQ’D.) WEDGE BASE LAMP SOCKET (4 REQ’D.) #194 WEDGE LAMP 14V., .27A (4 REQ’D.) #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ’D.) CARD RACK W/BOARDS ASSEMBLY TRANSFORMER BOARD ASSY. UNIVERSAL POWER SUPPLY ASSY. — CARD RACK R-G-B INTERFACE BRD. ASSY. AUDIO AMP P.C. BRD. ASSY. AUDIO AMP & HEAT SINK BRKT. 1/2” SPACERS (4 REQ’D.) #6 x 3/8 SLT. HEX HD. SCR. (4 REQ’D.) #6-32 x 3/8 SLT. PAN HD. SCR. (2 REQ’D.) #6-32 HEX NUT (2 REQ’D.)
5-15
NO. 576 — ROBBY ROTO — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)
ORDER BY PART NUMBER ONLY
20 A775-00013-0000 FAN ASSEMBLY 0151-00081-0000 4" FAN 0775-00110-00XF FAN PLATE 0749-00106-00XF VENT SCREEN 0017-00101-0347 #6-32 x 1/2 R.H.M.S. (4 REQ’D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00103-0005 #6-32 HEX NUT (4 REQ'D.) 0017-00101-0026 #8 x 5/8 SLT. HEX HD. M.S. (4 REQ’D.) A927-00019-0000 COIN BOX ASSY. A962-00004-0000 COIN BOX COVER ASSY. A962-00005-0000 COIN BOX SIDE CHANNEL ASSY. — SHORT 0962-00101-0000 COIN BOX SIDE CHANNEL — SHORT 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00104-0022 #8 WASHER (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) A090-00300-07BK U.S.A. 25¢ DOUBLE COIN DOOR ASSY. A088-00014-0000 INTERLOCK SWITCH & BRKT. ASSY. 0017-00003-0187 6" x 9" SPEAKER — 8 OHM, 9W (2 REQ’D.) A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY.
ADDITIONAL PARTS LIST
LOW VOLTAGE CABLE ASSY. HIGH VOLTAGE CABLE ASSY. MASTER CABLE ASSY. VIDEO ADAPTOR CABLE ASSY. VIDEO SIGNAL CABLE ASSY. FORMED HIGH VOLTAGE SHIELD HIGH BASE LEG KIT ASSY. — OPTIONAL 16 FT. LINE CORD A576-00009-0000 A576-00010-0000 A576-00011-0000 A576-00012-0000 A576-00013-0000 0927-00907-0000 A927-00005-0000 0017-00003-0064
NO. 530 — ROBBY ROTO — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY.
NO. 530— ROBBY ROTO — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY. — PARTS LIST
ORDER BY PART NUMBER ONLY
PART NO. DESCRIPTION
0595-00105-0000 0017-00003-0043 0017-00021-0005 0017-00031-0036 0017-00003-0412 0017-00101-0573 0017-00104-0009 0017-00003-0019 0017-00003-0026 0017-00101-0598 A961-00042-0000 FLUORESCENT BRKT. 18” COOL WHITE FLUOR. LAMP FLUORESCENT LOCKS (2 REQ'D.) FLUORESCENT SOCKET (2 REQ’D.) FLUOR. STARTER HOLDER W/LEADS #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ'D.) #6 EXT. WASHER (4 REQ'D.) FLUOR. STARTER BALLAST #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ'D.) LINE FILTER ASSY. — NOT SHOWN
ROBBY ROTO — CONTROL ASSEMBLY — ALL VERSIONS
5-18
ROBBY ROTO — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST
ORDER BY PART NUMBER ONLY
| 1 | A932-00022-0000 | BALL & SHAFT ASSEMBLY |
| 2 | 0017-00100-0025 | 1/4 E-RING |
| 3 | 0921-00702-0000 | STOP SPACER |
| 4 | 0921-00902-0000 | SLIDE PLATE |
| 5 | A595-00006-0000 | PIVOT PLATE WELD ASSY. |
| 6 | 0017-00101-0637 | #8-32 x 1" CARRIAGE BOLT (4 REQ’D.) |
| 7 | 0017-00103-0061 | #8-32 HEX NUT W/SEMS (4 REQ’D.) |
| 8 | 0932-00902-0000 | GROMMET |
| 9 | 0017-00101-0598 | #8-32 x 5/16 SLT. HEX HD. M.S. (10 REQ’D.) |
0962-00904-0000 SLEEVE #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) SWITCH PLATE (4 REQ'D.) SWITCH ASSEMBLY (4 REQ’D.) STOP PLATE & SWITCH BRKT. ASSY. WEAR PLATE ACTUATOR 0017-00101-0527 0020-00202-0000 A932-00009-0000 A932-00012-O0XF 0932-00905-0000 0921-00700-0000
5-19
FRONT DOOR ASSEMBLY — U.S.A. 25¢
FRONT DOOR ASSEMBLY — U.S.A. 25¢
0090-00002-02BK 0017-00101-0121 A090-00073-02BK 0017-00101-0123 0017-00007-0019 0017-00101-0552 0090-00117-03XF A097-00005-0000 A097-00006-0000 0090-00128-00XF 0017-00005-0041 A090-00096-0000 0090-00126-01XF 0017-00101-0525 A090-00096-0000 0090-00903-9500 0090-00143-00XF 0017-00003-0219 0017-00031-0048 0017-00103-0084 A090-00089-0000 0017-00101-0124 0017-00032-0051 0017-00032-0007 0017-00072-0034 0090-00173-0000 A090-00082-0100 A090-00087-0000 0010-00134-0000 0010-00181-0000 0017-00007-0083 0090-00129-00XF 0090-00167-00XF 0093-00155-00XF 0017-00100-0018 A090-00088-0000 A090-00085-0000 0017-00005-0003 0017-00005-0211 0017-00005-0214 A090-00064-0000 0017-00101-0099 0090-00162-00XF 0017-00005-0203 0017-00005-0195 0010-00599-0000 0017-00007-0132 A090-00059-0400 0017-00101-0698 A090-00077-0000 OCWMDNADARONA ORDER BY PART NUMBER ONLY
ITEM PART NO. DESCRIPTION
DOUBLE ENTRY COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) DOUBLE ENTRY COIN DOOR W/DRESS PLATE #8 x 1/4 UNSLOT. HEX HD. SCREW (4 REQ'D.) KEY HOOK #6-32 x 1/4 CARRIAGE BOLT (4 REQ’D.) COIN ENTRY PLATE — 25¢ (2 REQ'D.) DOOR LOCK & KEY W/SCREW & NUT (OR) DOOR LOCK & KEY W/SCREW & NUT DOOR TILT SWITCH BRKT. DOOR CAM DOOR TILT SWITCH SWITCH BACK-UP PLATE #5-40 x 9/16" PHIL. HD. M.S. (2 REQ’D.) DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 25¢ WINDOW (2 REQ’D.) COIN PLEX RETAINER 12 VOLT LAMP — G.E. #194 (2 REQ'D.) WEDGE SOCKET W/BRKT. (2 REQ'D.) #6-32 HEX NUT W/SEMS (4 REQ’D.) COIN METER W/DIODE #6 x 1/4 UNSLOT. HEX HD. SCR. (8 REQ'D.) PUSH BUTTON SWITCH SLIDE SWITCH STEEL OVAL HD. RIVET COIN COUNTER MTG. BRKT. TEST SWITCH & BRKT. ASSY. (ITEMS 23 THRU 25) COIN CHUTE & TOP ASSY. (2 REQ'’D.) SPRING SPRING 1/8 x 1-5/8 ROLL PIN PIVOT POST PIVOT LEVER REJECT LEVER E-RING REJECT LEVER ASSY. (2 REQ’D.) (ITEMS 30 THRU 33) COIN ACCEPTOR FRAME ASSY. (2 REQ'D.) COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) (OR) COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ’D.) (OR) COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) ANTI-PENNY DEVICE #6 x 1/4 SLT. HEX HD. M.S. (2 REQ’D.) COIN SWITCH MTG. BRKT. COIN SWITCH CHUTE COIN SWITCH COIN SWITCH WIRE PUSH-ON RING COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) #4-40 x 3/4 SLT. RND. HD. M.S. (2 REQ'D.) COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43)
5-21
VI Technical Troubleshooting
Introduction
The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.
General Suggestions
The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.
Harness Component Troubleshooting
Typical problems falling in this category are coin and credit problems, power problen.s and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the siug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.
If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.
Transformer and Line Voltage Problems
Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.
HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occurin areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning
the power off and disconnecting devices that may be
causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of ihe fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. if the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is.
In many cases, the input will be +5 VDC. If so, use the
VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.
A Glossary of Microprocessor Terms
MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions. CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.
EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.
ROM — read-only memory. The program, or binary
on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).
Introduction to the
Z-80 CPU
The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market tiirough the following factors:
6-3 The Z-80 is fully software compatible with the popular 8080A CPU. Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
- CPU (Central Processing Unit)
- Memory
- Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
General Purpose Registers
There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external
M,
inca «2 SYSTEM ono 2] CONTROLS —— 2 RD ——— we we 2
RSH 28 __
HALT <———
walt = ———_»| cpu CONTROL int = —8 51 wwii = 7 9} RESET —28_»| cPU aus — my BUS aus =| CONTROL .
® sv
GND) ————» 2-80 CPU
Z-80 PIN CONFIGURATION data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)
Subtract Increment
Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.
Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.
38, ADDRESS
- BUS
DATA BUS
Ao-Ais (Address Bus) Tri-state output, active high. Ap-A;5 constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. 1/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ay is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.
DoD, (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.
My, (Machine Cycle one) __ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request
signal indicates that the address bus holds a valid
address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The TORQ signal indicates that the lower half of the address bus holds a valid I/O address for a I/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.
6-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.
HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP's to maintain memory refresh activity.
WAIT (Wait) Input, active low. WAIT indicates to the 2-80 CPU that the addressed memory or !/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.
INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WATT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:
- Disable the interrupt enable flip-flop
- Set Register | = 00x
- Set Register R =00x
- Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.
BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated.
BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.
CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements. —_—___——_——_—_—eeE—KXK———_—
MCR II SYSTEM P.C. BOARD JUMPER OPTIONS
VIDEO GENERATOR P.C. BOARD
MANUFACTURER | EPROM NO.| JW#1 JW#2 JW#3 JWH4 JWHS JWHG JWH7 JW#B
ras
a Pa Te C.P.U. PC. BOARD
MANUFACTURER |EPROM NO.| JW#1 JW#2 JW#3 JWH4 JWHS JWHE NUMEROUS MFR'S | 2532 | | « | x | TION FOR JUMPER OP-
NUMEROUS MFR'S | # | ROMs ONLY. OUND I/O P.C. BOARD
| * | # | NUMEROUS MFR'S | 272 | # |e |
# = LEAVE JUMPER WIRES WHERE THIS SYMBOL “#” APPEARS
- = CUT JUMPER WIRES WHERE THIS SYMBOL “*” APPEARS.
The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the C.P.U. P.C. Board used in the MCR II System has 6 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires. All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut. The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wires number. If there is a “#” under a jumper wires number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.
VII. Coin Door Maintenance
SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150
COIN DOOR MAINTENANCE
METAL COIN ACCEPTOR MECHANISMS Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.
- Make sure the power to the game is off.
- Unlock and open the coin door.
TO REMOVE PUSH LATCHES DOWN
PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781
- Remove the coin acceptor mechanism as shown in Figure 7-1. Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.
PUSH MECHANISM IN
Figure 7-1 Removing and replacing coin acceptor
- Clean the magnet of all foreign particles. See Figure 7-2. This may be accomplished by swinging the gate open as shown in the above figure.
- Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) 0 Also clean the pivot pin.
- Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: O Place the coin acceptor in boiling water for about ten minutes.
O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.
GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE
Figure 7-2 Cleaning the metal coin acceptor
- To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. C Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
- WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
- Check the coin chute for obstructions such as. paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-1. O Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
APPLY POWDERED GRAPHITE HERE
CRADLE
Figure 7-3 Lubricating the metal coin acceptor
7-2
SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN
HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT
Figure 7-4 Opening the plastic coin acceptor
PLASTIC COIN ACCEPTOR MECHANISMS
The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned
- Make sure the power to the game is off.
2.
3. Unlock and open the coin door.
Remove the coin acceptor mechanism(s) as shown in Figure 7-1. © Push down on the two spring loaded latches. 0 While holding the latches down, pull the top of the acceptor mechanism toward you. O Release the latches and lift out the mechanism.
. Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. O Clean the mechanism in hot soapy water. It never rusts. _ _ 0 Rinse the mechanism in clean hot water and allow it to dry.
7-3 O Reassemble the mechanism (it never needs lubrication).
- Check the coin chute for obstructions such as: paper, gum, etc.
- Reinstall the coin acceptor to the coin door. See Figure 7-5. D Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
- Close and lock the coin door.
ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.
SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.
TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.
Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.
jenuep 1opxUOW| ALIA NOA ANVHL INOA d13H OL AQVAY GNV.LS SHOLNGIHLSIG HNO GNV 44V.LS HNO “SHAdVd SAWVD YNOA HLIM G3dIAOd"d HASWNN 3384 TIOL SHL LY ANVdNOOD ONIEN.LOVANNVYW AVMCIN YO YOLNEIYLSIG HNOA LOVLNOO ASV31d ‘SNOILSSNOD 3AVH THLS GNV NOILOAS SIHL HDNOYHL AVS" NOA JI “HOLINOW ‘A'L SAWV9D YISHL ONIYIWdSY OGNV ONILOOHS31ENO.L NI 33YD30 SOINOWLOA1a NV LNOHLIM ASOHL GIV OL GAGNILNI S! GNV YANNVW GONV.LSYSGNN OL ASV3 NV NI C101 SI NOILOJZS SIHL NI GANIVLNOO NOILVWHOSNI SHL ‘S.LON ASV31d
Color T.V.
Color T.V Monitor
Introduction: (How to use this section of your manual.)
This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFULI!
If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.
If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings
8-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:
- Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it. Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part. Next, go to the schematic section and find the schematic that matches your monitor. It may be heipful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.
That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)
Symptom Diagnosis
. Insufficient width or heighth: A. Horizontal tine (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. O Bad vertical output section. OU Open fusible resistor in vertical section. O Bad height control. D Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). 0 Bad yoke. Open width coil. O Open part in horizontal! output section. Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal. . Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).
8-2 10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).
Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.
Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.
Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.
No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).
No brightness, high voltage present; check: A. Heater voitage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.
No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moom>
No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.
. Moving bars In picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.
24, Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interferring. —. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.
Guide To Schematic Symbols
THERMISTOR (POLARITY DOESN'T MATTER)
SV WL INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)
(-) CATHODE
(+) ANODE
ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)
VL
FUSE (POLARITY DOESN'T MATTER)
CATHODE (-)
ANODE (+)
DIODE
COLLECTOR Te COLLECTOR a BASE ———— BASE———> EMITTER net EMITTER mS
NPN TRANSISTOR PNP TRANSISTOR
' Vw
VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN’T MATTER) (POLARITY DOESN'T MATTER)
+ +
LINES ARE CONNECTED ELECTROLYTIC CAPACITOR
LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)
hog & GROUND
8-4
Troubleshooting
Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to.the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:
- Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors.
- Resistors.
- Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS!! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.
Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.
Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.
First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.
To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onhmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.
Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.
Theory of Operation
To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.
THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice,
constant, smooth voltage so that the monitor circuits
don’t jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or none atall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discusged later. THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.
An interesting aside is that our sync is composite negative sync. That means two things:
- The sync is a negative going wave form.
- There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz).
The sync is amplified by a sync amplifier transistor and sent on its wey to the oscillators. The sync or timing information wil! be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.
VERTICAL AND HORIZONTAL DEFLECTION — After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assmebled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” or 19” color monitor uses transistors for its sync section. An Electrohome 13” or 19" color monitor uses an integrated circuit 1C501 for its sync section. The idea is all the same. The output to the vertical amplifying transistors for all monitors must be a sawtooth wave form, sort of like a bunch of pyramids, racing to the yoke’s vertical coils at 60 times a second. Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set. The amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.
8-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Again, Wells Gardner uses transistors for the horizontal oscillator, and Electrohome uses the other side of IC501. Still, the effect is the same. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillators frequencies must match, so the picture doesn't appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.
THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyoack” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.
COLOR CIRCUITS The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There only two, one for the red and one for the green. The
blue doesn’t have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.
PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check the emitter on TR502 of the Wells Gardner monitors; or the emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Wells Gardner = 127VDC Electrohome = 120VDC
The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, the GO7-FBO or G07-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.
THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuits work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The
cathode can arc or short to the heater resulting in no
picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.
Differences Between Monitors
The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to see if there are two circuit boards rising up from the chassis toward the picture tube neck. In other words, they stand up, or are perpendicular to the chassis, with a black plastic bracket holding them in place. This is a description of a Wells Gardner monitor. They use separate boards for main chunks of circuitry. Therefore, you have a “power board” (the power supply), an “interface board” (the interface section), and a “horizontal/ vertical board” (for the deflection circuitry). Still, there are a few parts on the chassis, but most can be found on the board. An Electrohome monitor has no separate boards, except for the neck board, and just has a flat chassis.
Another good way to determine which monitor you have is to check the transistor call out numbers that are printed on the chassis next to the part. For instance, on the neck board, one of the color output transistors is TR401. If you look through the schematics or the parts lists, you will find TR401 in the Wells Gardner literature. On the other hand, the neck board transistor may say X101. X101 can be found in the Electrohome literature. So, all Wells Gardner transistor call outs begin with TR, and Electrohome transistor call outs start with an “X”.
Parts Interchangeability Some parts can be interchanged on all of the monitors. Here are the rules:
1. You CAN swap the voltage regulator TR502 or X01 on any Wells Gardner or Electrohome 19 inch monitor. You CAN NOT swap the voltage regulator on the 13 inch Wells Gardner or Electrohome (G07-902) since the Electrohome uses an integrated circuit for the power supply.
You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance.
You CAN swap any capacitor between monitors that has the same capacitance, and voltage rating.
PICTURE TUBES: Due to the fact that “ELECTROHOME” is now (October, 1981) using a picture tube with an internal shield, these picture tubes can be used in EITHER “WELLS GARDNER" or “ELECTRO- HOME” monitors. However, a “WELLS GARDNER” picture tube can ONLY be used in a “WELLS GARDNER” monitor. It will not function properly if installed in an “ELECTROHOME?” monitor. The picture purity will be off.
- You CAN NOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-904) monitor “flyback”. looks identical to the 19 inch Electrohome (GO07-904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTERCHANGEABLE!
- You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part. ne ee eee eee]
Monitor schematics and parts lists omitted
IX Schematics and Wiring Diagrams
(EPR RFRRFR POWER SUPPLY BD. ‘ote 9082-9000 (SEE NOTE Fa)
i 24 POS,
'
;
aus
oe ee)
pote 91368-2060
AUDIO AMP BO. 064- 90312- 4930 NOTES? 1. x ntos,wine 2864, coow SUL. WE H
4, EITHER POWER SUPPLY MAY BE UseD "# A082-80421-B000. OR ‘A082 - 90411 C00 = = 9 260s MONITOR, | ROMER’ oa) ere
MT 92 XFORMER
‘COIN DOOR oie a ed om ae ‘semvce_ourter ora @ voit a At
7 2 awe 1° Sia DATE NAME MIDWAY MFG CO. slits fe tsepal 10601 W. BELMONT FRANKLIN PARK ,ILL, 60131 ROTO UR. mre omnoe eae Wo5I-00830-A003 Lane Filter
4-18-82 MA > ory ON-OFF Sm, cory Bue
SAFTEY Sm.
9-1
'
'
i
t
'
t
'
'
'
'
'
'
i
H
H
'
'
'
'
d
| Tel vey | at | Goa |
aE q mun it
| POWER SUPPLY BD. | T | = | = | 2 POs |
| tote -s0te-9000 | pelesy | a | |
| (Se Note ta) | pol ow. | y-vi0_ | be! |
| a | ee | Pea | |
| sa | = | i! |
wor_j tee! v2 Pos 19 Pos Led
NOTES? 4. wewca,wine 21864, 004 INSUL, RE
- G-¥ GND, GOES TO ON-OFF 54, MoneroR, <o DOOR AUDIO AMP BD. s084-90012-4530 3 wer wer
vw AyoH0.
usvoo neryan,
ver
wow ome. si =
so wor a L___prrng
nts +
9-2 USED #A082~90421-B000 OR
eee 7 Tint ME ie bi J
ie Dory \ fROTO MINI
$MO5I-00674 ~ADO3 REVISION. DATE NAME MIDWAY MFG CO. 72 [atevee |i. tenga] 10601 W. BELMONT
FRANKLIN PARK ILL, 60131
4-13-82 MK. xy
‘ote 91363-1000
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DESIG, NO.
¢ 100 e101 © 102 © 104 ¢ 105 ¢ 106 e107 ¢ 108 los Ho
gas
L100
8100 DESIGNATION LIST.
DESCRIPTION
to wt RAD. TANT 0.47t RAD. TANT 470 pt AX. ELECT 0.047 wf ESTR 25000 mf AX. ELECT 4.7 yt RAD. TANT 0.1 at AX. CER 0.1 pf AX. CER. 001i ESTR 0.082 wt ESTR 0.01 pf ESTR
- wf AX. CER. O.1 wt AX. CER. 40000 pf AX. ELECT 470 pf AX. ELECT 2200 pf AX, ELECT 4700 pf AX. ELECT AT pt AX, CER. 0.1 git AX. CER. 0.01 pf AX. CER. 820 pf AX. CER. 0.1 wt AX. CER.
100 ohm 470 ohm 18 ohm 216 ohm 68 ohm 24 ohm 270 ohm 2M 2M i 33K 220k 75K eK 560 ohm 2k 33M uM tom 100k Lek 75K 360 ohm 3.9K 25 ohm 68 ohm 10 obm 1K 6.2K 1K 270 ohm 82 ohm 150 ohm
100 ohm 100 ohm 100 ohm
IN alae IN 4I48 IN 4148 IN 4001 IN 4001 IN 4001 MR 750 MR 750 IN 4001 11N 4001, AIS AISE AIS AISF AISF ANSE AISF
2n2905,
2N4a401
2N2905
L305
anze
LM3900
LM 305 1/4 5% 1/4W 5% 5W W/R.S. I5W W/R.S. vew vaw vaw aw vaw vaw vaw vaw vaw vaw vaw vaw vaw vew vaw aw aw vaw vaw vaw 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5W W/R.S. vew aw vaw vaw vaw vaw 1w aw
Por por Por
RES
REG 5% 5% 5% 5% 5% 5% 10% 5%
-22,nH INDUCTOR
BATTERY 3.6VOC 60 DES-c DESIG. NO.
Fi Fe FCIA,IB Fo 28,28 FBI,2 Twi-2 1W3,4 va
ve
usr pe a3
HsAL
MH HSA MH HSA IA, 28 MH HSA 18,28 10,20. MHHSAIE,2E
wWIe8 FB MHI,2 DESCRPTION
1A NORMAL BLO 1/48 8L0-BLO FUSE CLIP FUSE CLIP FERRITE BEAD TIE WRAP 1083/4" TIE WRAP 7.8 5/8" 8 PIN P.c. MOUNT 13PIN P.C, MOUNT 5 PIN P.C. MOUNT 6 PIN P.C, MOUNT V/4& FUSE TAG 1A FUSE TAG
1D POWER SUPPLY TAG
HEAT SINK ASS'Y |
MOUNTING HARDWARE
4-40X10 SLT RND SCREW
WASHER 4-120-.250-018
HEX NUT 4-40
22.8WG JUMPER WIRE,
FERRITE BEAD MOUNTING HAROWARE
ows Cees]
oS
@ E R102 prone ene sa t ' t ‘ t ' ' ' '
‘
i
'
'
' '
' ! '
i
i t ' ' '
' i
t
i
i
' i i °
aN
\S
L
WH NOTE | RE~ RESISTOR SPICER
PROJ. ENG: _L. DEKKER CROSS REFERENCE LIST
DESCRIPTION
AT of AX, CER. 820 pt AX, CER. 0.01 pt AX, CER. 0.01 pt ESTR 0.047 pf ESTR 0.082 wt ESTR Out AX. CER.
0.47 pt RAO, TANT 4.7 wf RAD, TANT 10 wt RAD, TANT 470 yf AX. ELECT 2200 af AX. ELECT 4700 wt AX. ELECT 25000 gf AX. ELECT 40000 wf AX. ELECT
-I6 ohm I5W 5% (W/RESISTOR SPACER) 118 ohm 5 W 5% (W/RESISTOR SPACER) 1Oohm 1/4W 5% 24 ohm 1/4W 5% 25 ohm SW 10%(W/RESISTOR SPACER) 68 ohm 1/2W 5% 82 ohm IW 10% 100 ohm 1/4W 5% 150 ohm 2W 5% 270 ohm 1/4W 5% 360 ohm 1/4W 5% 470 ohm 1/4W 5% 560 ohm 1/40 5%. 1K 1/4W 5% 2K 1/4W 5% 3.9K 1/4W 5% 6.2K /4W 5% 33K 1/4W 5% 75K 1/4W 5% 100K 1/4W 5% 220K 1/4W 5% IM aw 5% LIM 1/4 5% 12M 1/4W 5% 2M 1/4W 5% 3.3M 1/4W 5% IOM 1/4W5% 100 ohm POT
AISF RECTIFIER
MR 750 IN4oo! Inaias 2N2905 2Naaor 4n26 LM 305 LM 3900 22 yH INDUCTOR BATTERY 3.6VDC 60DEG-C FUSE 1/44 S-BLO FUSE IA N-BLO FUSE CLIP FERRITE BEAD TIE WRAP 1083/4" TIE WRAP 7.8 5/8" SPIN P.C, MOUNT 6 PIN P.C. MOUNT 13PIN P.C, MOUNT 22 ANG JUMPER WIRE FERRITE BEAD MOUNTING HARDWARE 1/4 FUSE TAG 1A FUSE TAG TAG~ 1D POWER SUPPLY
P.c.8.
4=40X10 SLT RND
WSH 4-120-.260-018
4-40 HEX NUT
HEAT SINK ASS'Y Q'ty
' ' '
fl '
- oma e-News Yo WH =~ ~~ uw ewe
-waw-
\_PER DESIG. NO.
cur e120 ci 6108, 110 6103) C109 ©1096, 107,101,112, 118,121.
C105
102,114 cus cue e104 cus,
R103 R102 R26 R105 Ri24 R104, 125 RIB R100 RI32 106,130 Rize R101 Ria R127, 129 R113, 115,120 Ri23, RI28 R110 R112, 121 Rus Ri R109 RUT R108 R107 Rie Rie R100, 101,102.
110,11, 12,13, 114,118,116 106,107 1 103,104,105,108,109 100,101,102 2102,104
us u2,5 ua L100 B100 F2 Fl FC 1A,1B,28,28 Fe1,2 Twi, TW3,4 whe v2 vt aWi-3 BMH, 2 Le! ie2
MHHSAIA,2A MHHSA 18,28, 10,20 MH HSA IE, 2E HAI PART NO.
0945~00811-0100 0945-00816- 0400 0945 ~00816- 0100 0945-00816 -0200, 0945 -00816-0300 0945-00816-1900 0945-0081! -0200
0945-00816 - 1100 0945-0081 0945-00816 - 0945 -00816-0600 0945-00816 -1300 0945 -00811-0700 0945 -00816-1700, 0945-00816 -1800
0945-00815 -0100 0945-00815 -0200 0062 -051B3~ xxx (0062-06583 -1Xxx 0945-00815 1000 (0062-09803 -1xxx 0945~-00815-0800 0062 -11083~1xxx 0945-00812-0200 (0062-13883 ~ xxx 0062-14 783~1xxx (0062 -156B3-IXxx (0062 -162B3 -1XXX (0062~-17983-1Xxx (0062-18383 ~1Xxx (0062 ~20783 -IXXX (0062-21783-1xxx (0062-25183 ~1xxx (0062-26983-1Xxx 0062~275B3~Ixxx (0062 ~29183-1Xxx (0062 ~32383-IXxx (0062-325B3-IXxx 0062 -32783-1xxx (0062 ~33783-Ixxx (0062-34783 ~1XxX (0062 - 37183 ~1XXx 0945 - 00814 -0000
(0945-00804-0200
0945-00804-0800 0945-00806 - 0300 0945-00804 -0500 0945- 00808-0300 0945~00804-0400 0945-00813~0300 0945-00813 0100 0945-00813-0200 0945-00814 -0200 0017 - 00003-0377 0017 -00003-0446 0017 ~ 00003-0001 0017- 00003-0214 0017 -00009- 0225 0945-00814-0400 0945-00814-0300 3000-16387-0800 3000 -16387- 0600 3000-16387 -1300 0151-00087-0000 0017 00033-0139 MOSi-00945-a020 MOBI - 00945 ~ A021 Mo5!-00945~A022
4080-90421-8000
0017 ~ 00101-0727
0017-00104-0071
0017 -00103- 0002
A945-00945-0100 0 SEE HSAI DRAWING NOTE.
MIDWAY MFG. CO.
ASS'Y DRAWING
A082-39042I-BO00 SPRTT aa MEDIUM PWR SPLY 7OVA W/CKT 105 1-00945-B0Ol
(MIDWAY MFG. CO. 45-807
CRO EFERENCE LIST
| DESCRIPTION | QTY | DESIGN/TION | PART NO. |
| 0.1 MF AX.CER, | 32 | CPI-CP32 | 0789-00800 -0900 |
| 1S MF AX. TANT. | 3 | cl-c3 | 0174-207D 6-EXGX |
bse ais ee CEB EB
| lo OHM 174 w5% CRBN | 4 | RI-R4 | 0062-113B3-IXXX | ||
| 220 | I | R5 | 0062-133B3-1XXX | . | |
| ik " | _— | * | 8 | R6-RI3. | 0062-179B3-IXXX |
| 4027 | 16 | UI-UI6 | 0789-00803- 4900 | CePz0) CCP2T) | |
| 74F08 | 1 | u22 | 0789-00803- 5000 | ||
| 74LS14 | ' | v2i | 0789-00803- 3600 | ‘U7 | |
| 74Lsi66 | 2 | ul7,U20 | 0789-00803- 3500 | ||
| 74LS253 | 2 | Ul8, VIS | 0789-00803-4800 |
CoPIsD CIFIE) CEPI CCIE nn
| P.C. BOARD EXTRACTOR | OMHI, DMH2 | 0789-00806- 0200 | ||
| RAM BOARD | | | A080-91356-C000 | | | a |
DESIGNATION LIST Fl TF
DESIGNATION DESCRIPTION
: ° a a Ccl-c3 ISMF AX. TANT CPI-CP32 O.IMF AX. CER. ou ale RI-R4 {110 OHM I/4w 5% CRBN.
| RS | 220 " | " | ||
| RE-RIS | ik" | " | " | “ |
Ul-UI6 4027 UIT 74LSI66 UI8,UI9 T4LS 253 u20 74LSI66 v2l 74LSI4 u22 . 74F08 veees ROTO MIDWAY MFG. CO. NO. KID 2 PER FRANKLIN PK. ILL OMHI, DMHZ P.C. BOARD EXTRACTOR : PART NO
ASS'Y DRAWING RAM BOARD MO51-00789-COOl
A082-91356-COv0
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DESIGNATION
cl ce C3-C5 ce c7,ce CPI-CP28
RI-R3 R4 RS R6 R7 R8,RO RIO RU, RI2 RI3 R2t R22 R23 R24 R25 R26 R27 R28 R29 R30
ol
Ql 2,93 Qs Q6-08 es Qo
ul u2 U3 U4 us U6 U7 us us ulo
9-8 DESCRIPTION.
33PF AX.CER.
| opr | “ | * |
| OlMF | " | " |
| 270PF | " | " |
1S MF_AX.TANT. 0.1 MF AX. CER.
2.2K OHM 1/4w5%CRBN oH wm
| 47 | oo | ow | won |
| 22k | " | ef | "8 |
sso."
| 22 | " | * | "8 | |
| 82 | sow | ow | ||
| eek | "oo" | ome | ||
| eek | " | "um | ||
| sik | " | oo" | eo | 4 |
| io | OU" | OU | ||
| ar | sow | oe | ||
| eek | " | "#4 |
510 .
| a? | sow | wa | |
| ik | * | * | 8 |
a? woo4
| 220 | " | "um |
IN4I48
MPS-H69 2N4401 2N4401 MPS-H69 2N6427 2N4401
74LS20 T4LSi74 CUSTOM ADDRESS: 7416 74874 74LS04 T74LSIO T4LSI75 74LS08 T4874 DESIGNATION LIST.
DESIGNATION, DESCRIPTION
ull ul2 us ula us: UIs vI7 uls ula u20 ual
Icsu3 icsulds Icsul7 Icsu2t
X- TALI OMHI, OMH2 HSUIS 7402 74LS257 74LSI57 74LS00 CUSTOM DATA 74L8257 3880 CPU 4024 T4LSI75 74LS04 74L$245
40 PIN IC SOCKET ow
20PIN " "
14.318 MHZ CRYSTAL P.C. BOARD EXTRACTOR HEAT SINK CROSS ___ REFERENCE LIST
DESCRIPTION
33 PF AX. CER. 1OO PF AX. CER. 270PF AX. CER. 0.1 MF AX. CER. 18 MF AX. TANT. paton
47 OHM 1/4w5% CRBN.
| eo" | “" | "4 | ||
| oo | " | " | "8 | 8 |
| 220 | " | ow | oon | |
| sI0 | * | oo | ow | ow |
| 560 | " | won | " | |
| 22k " | oon | ” | ||
| sik" | "= | 8 | # | |
| lox | " | oom | oon | |
| wk" | oom | oe | ||
| 22K" | "= | 8 | 8 |
NT TT NN KT ONS
IN4146 DIODE
2N4401 2N6427 MPS-H69: ame
3880 CPU 4024 74LS00 7402 74LS04 74LS08 74LsIO 7416 74LS20 74874 74Ls74 74LSIS7 T4LSI74 T74LSI75 74LS245 74LS257 CUSTOM ADDRESS CUSTOM DATA ep -w eo ee ome eee
20 PIN IC SOCKET 40" " * CRYSTAL P.C. BOARD EXTRACTOR HEAT SINK
CPU BOARD pr an _QTY. DESIGNATION
cl c2 cé C3-C5,CPI-CP28 c7,c8
RG,R24,R27, R29 RIL, RIZ R23 R30 R26 R8,RO RI- R3,R7,RIO, RIS. R22 R2e RS R4,R21
DI
22,03,05,Q10 t-) Q1,06-08
ul? vis ula uu ue, u20 us u7 u4 ul us ulo urs v2 U8, Ula vat ul2,UI6 u3 vis
icsuat ICSU3,ICSUI5,ICSUIT X-TALI DMHI, DMH2 HSUIS PART_NO.
0789-00800- 1400 0789-00800-1500 0789-00800-0500 0789-00800-0600 0174-2070 6 - EXGX
0062-086B3- [XXX 0062-104B3- Xxx 0062-1 10B3 - Xxx 0062-133B3-1XXX 0062-159B3-1XXX 0062 -162B3-IXXxx 0062-195 B3-IXxxX 0062-213B3-IXXX 0062-227B3-IXXxX 0062-229B3-IXXX 0062-243B3-IXXxX
0789- 00801-0200
0789-00802-0300 0789-00802-0400 0065 -467XX -XX6X
0789-00803-0300 0789-00803-0200 0789-00803-0700 0789-00803 -0800 0789-00803-0900 0789-00803- 1000 0789-00803- 1100 0789-00803- 1200 0789-00803- 1300 0789-00803- 1500 0789-00803-1600 0789 -00803-0400 0789-00803-0500 0789-00803-0600 0789-00803 -5100 0789-00803- 1400 0789-00803- 5200 0066 -1 18 XX -XXYX
0069 -132XX-XXWX 0069-1 09XX-XXWX 0789 -00806-0100 0789- 00806-0200 0068- O6IXX -ABAX
A080-91354-FO0O
MIDWAY MFG. CO. FRANKLIN PK. ne.
ASS'Y DRAWING CPU BOARD A082-91354-FO00 051-00789-F006
mat 01 —CED
10K rae seg
+ ATPER
+08
T4LS187 TaLso4 Als —C7e)
| Sof | ex | RFSA-—-CoT |
att, ‘T4L804 7augoo b> {m«) I v | 74us74 45 a 2. 12 2.2K
| 74L904 | se | 7402 | ena4ol/ | es $310 |
3 oe Uk R26 8 a 74.804 ’
| T4Ls04 | iz) n= | 2 | 2.8vREF |
T4LS74 +3
us - Tia
| L. | | | vip |
2.5mer
28 O.Imfd CAPACITORS (BP) NOT SHOWN
PROJECT ENG: J.JARON/D.OTTO useo on ROTO MIDWAY MFG. DO NOT SCALE DWG. No. REQ'D | PER. FRANKLIN PK. ILL. +3.8v
PART NO. DIM. TOLERANCES UNCLES weECINED SCHEMATIC CPU BOARD 051-00789-FO05 pe ame A082 -91354-FO0O HOLE OIA.
DESIGNATION LIST
DESIGNATION
ct c2 C3-cé c7 CPI -CP30
RI R2 R3 R4 R5-R26 R27-R34 R35,R36
ot Qi ul v2 u3 u4 us us u7 u8,u9 vio un ul2 UI3,Ul4 UIS,UI6 vi? XI- X10 x2l X22-X24 X31, X32
ICsuNl, ICS12 ICSIS - ICSI7 Icsxt-ICSIO ICsai- ICcs24 ICSX3I, ICSX32
TwI OMH1, OMH2
9-10 DESCRIPTION 0.1 MF AX. CER. 18 MF AX. TANT. 0.1 MF AX. CER. (S MF AX. TANT. O.. MF AX.CER.
470K OHM |/4w 5% CREN 220K “" * . « 220 ooo . "
1oK no 27K
in4004 2N440 74LSs08 74Ls32 7403 74Ls02 74Ls74 4078 74L8133 74LSI39 82siss 74Ls244 74Ls245 7417 748244 74LS245 EPROM KIT 8416-20 LOW POWER RAM 8416-20 RAM EPROM KIT
20 PIN IG SOCKET ° now ow
a" oo ow wow eu
3.6V NI-CAD BATTERY TIE WRAP P.C BOARD EXTRACTOR :
f nile Ae]
PROJECT ENG: J. JARON/D.OTTO CROSS REFERENCE LIST
DESCRIPTION
0.1 MF AX.CER. 15 MF AX. TANT.
NO OHM I/4w 5% CRBN
| 120" | " | oma | |
| 220 | ° | 0 | woo. |
| 27k " | " | won | |
| toK | “ | . | oon |
| 220K" | " | “oe | |
| 470k" | ” | won |
1N4004 2N4401
4078 74Ls02 7403 74LS08 7417 74LS32 74LS74 74LS133 74LS 139 74LS244 74LS245 828153 8416-20 LP. 8416-20 EPROM KIT
16 PIN IC SOCKET 20" * «
24PIN IC SOCKET
3.6V BATTERY TIE WRAP P.C BOARD EXTRACTOR
MEMORY BOD. Q'TY
er
on
NO RFD i] PER. DESIGNATION Cl,C3- C6,CPI-CP 30
R27-R34 Re R3 R35,R36 R5-R26 R2 RI
ol Ql
ue ua us ut UI3,UI4 u2 us u? U8,U9 ULL UIS,UI6 Ul2,UI7 ulo x2 X22-x24 Xt- X10, X31,X32
ICSX31,1CSX32 ICSUll, ICSUl2, ICSUIS- IcsvI7 ICSXI-ICSIO, ICSx21- Icsx24
BI Twi OMHI , OMH2
MIDWAY MFG. CO. FRANKLIN PK’ ILL. PART _NO 0530 - 00800-0300 0530-00800-0400
0062- 113B3-1XXxx 0062 - 116 B3-1XXX 0062 - 133B3 - IXXX 0062 - 199B3 - IXXX 00 62- 227B3-1XxXx 0062- 291B3-1XXxX 006 2-307B3-IXXX
0530-0080I-0200 0530-00802 -0500
0530-00803- 1400 0530-00803-0700 0530-00803-0500 0530 -00803 - 0800 0530-00803 - 0600 0530-00803-0900 0530-00803-1000 0530-00803-1100 0830 -00803-I200 0530-00803-!500 0530-00803-1300 5300- 26AAU-AXHD 0530-00803-1700 08530-00803-1800 A&30-90000-RO0O
0530- 00804-0300 0530- 00804-0400
0530 - 00804-0500
0530- 00804-0600 00I7- 00042-0048 0789-00806-0200
A080-91423-A530
ASS'Y DRAWING MEMORY BOARD A084-91423-A530 MO51-00530-A007
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
CROSS REFERENCE LIST
| DESCRIPTION | QTY | DESIGNATION | PART NO. | |
| 0.1 MF AXCER. | 2 | c2,c3 | 0530-00800-0500 | |
| 15 MF 20V AX. TANT | I | cl | 0530-00800-0600 | |
| 3.3 OHM Iw 5% CRBN. | 2 | R3,R6 | 0062-038F3-1XXX | |
| 330 =" | aw" " | 2 | RI, R4 | 0062-144B3-1 XXX |
| 200 “ | POT | 2 | VRI, VR2 | 0063-050AX-IDEX |
| 1N4004 | DIODE | 2 | DI, D2 | 0530 - 0080! - 0300 |
| 2N4403 | 2 | Q1,a2 | 0530- 00802-0600 | |
| TIP 31 | 2 | Q3,04 | 0530- 00802-0700 | |
| KK 156 10 POS. | I | Jt | 3000- 16387-1000 | |
| AUDIO AMP | I | A084 -90912-A530 |
DESIGNATION DESCRIPTION
cl ISMF 20V AX.TANT c2,c3 O.IMF AX.CER.
RI : 330 OHM |/4w 5% CRBN.
| R3 | 330" twos" | PROJECT ENG: J. JARON/D.OTTO | ||||
| R4 | 330" l4w" | " | ||||
| RG | 3.3 | “ lw | “ | o | DO NOTSCALE DWG. | ~ |
DIM. TOLERANCES
| VRI,VR2 | 200 OHM POT | ee |
ee DI,D2 IN4004 DIODE REVISIONS , [___nevisions. Os—=~S*S
| — | once | MIDWAY MFG. CO. | ||
| @i,a2 | 2N4403 | FULL | vo.rea> | PER. | FRANKLIN PK. ILL. |
| 3,04 | TIP3I | ASS'Y DRAWING | PART NO. |
AUDIO AMP BOARD MO5 | -00530-A009
| vl | KKI56 10 POS | A084-90912 -A530 |
AUDIO IN NO.I
AUDIO COMM
3.3 OHM IW FUSABLE
AUDIO INNOZ( 3»)
BS onm \w FUSABLE
+e 18 cl ISMF AUDIO RETURN
je . HEAT TREAT SCALE DO NOT SCALE DWG No.REQ'D | PER FRANKLIN PK. ILL.
DIM. TOLERANCES zy eee : 1 K ice lag nn concentmery rin 0094 AUDIO AMP 05 1-00530-AOl0. mote cia... ¢ 062. 00¢24TEQS/IG/ B2 | A080-90912-A530
DESIGNATION LIST
RS. R9,RIO RU,RI2 RIS RIG RIS RIG,RIT Ris RIS R20 R2I R22 R23,R24 R25 ol Qi
ul
DLI,OL2
a v2
MHI- MH4 Ql AX. CR. 1.5K OHM I/4W 5% CRBN won on 2k "
| 3K " | ooo | " |
| 6.2K " | oom | on |
2k oo wow 3k" Ce L5K Cr ik " oo oun LK wow ow 2k " wow on
| 43k " | oon | ow |
leo " wouoe ik “ no owow 62k “ wowioa 620 " wow ow Lek ™ won oa 100 “ wouwoa ik" wow on
| 160 “ | wow | ow |
| ik" | wom | oon |
IN5232 2N4401
TBA 530
270 NS DELAY LINE
CONN-KK 100-RA-9 PIN CONN-KK 100 -RA-12 PIN SNAP BUSHING 1/4"
| CROSS | REFERENCE | LIST | |||
| DESCRIPTION | QTY DESIGNATION | PART NUMBER | |||
| QUMF AX CR | 3 | CPI-CP3 | 0789-00800-0400 | ||
| 100 OHM 1/4W 5% CR | \ | Rl | 0062-110B3-1XXX | ||
| leo " | “eS | 3 | ~—s«RIG,R23,R24 | 0062-124B3-IXXX | |
| 620 " | " | "8 | I | RID | 006 2~168B3~1XXX |
| ik" | oN | NS | 6 | RY,RIO,RIGRIT | 0062 -179B3-1XXX |
R22,R25
| wk" | oN | Me | ' | R20 | 0062-183B3-IXXX |
| kK" | "of | 8 | \ | R7 | 0062-165B3-IXXx |
| 6K" | "ofS | 4 — RLRB,RI,RI2 | 0062-167B3-IXXX | ||
| ek" | "oo" | 3 | R2,R6,RI3 | 0062-193B3-1XXX | |
| 3K" | UN | 3 | R3-R4 | 0062-201B3-IXXX | |
| axk" | "NM | ' | RI4 | 0062-209B3-IXXX | |
| 62k" | " | "8 | 2 | R5,RI8 | 0062-21 7 B3=1XXX- |
| IN5232 "ZENER | ' | ol | 0789-00801-0100 | ||
| 2N4401 | \ | Ql | 0789-00802-0200 | ||
| TBA-530 | ' | ul | 0789-0 0803-5300 | ||
| 270 NS DELAY LINE | 2 | OLI,DL2 | 0069-I66XX-XAMX |
CONN. KK-100 RA (9 PIN) CONN. KK-I00 RA (12 PIN)
| SNAP BUSHING 1/4" | 4 | MHI- MH4 |
| RGB PCB. | \ | - |
ce 3000-16366-0900 3000- 16366-1200
0017-00042-0 014
A080-91363-C000 q LJ
PROJECT ENG: J. JARON/D.OTTO MIDWAY MFG. CO.
DO NOT SCALE DWG. . \ PER . 7 Asay, Dee = ri etlen. RGB INTERFACE. PC. 051-00 673-8028 Poon eee | A080-91363 -8000 DIM. TOLERANCES uNLess speciriep orn. TUK
ple vey R25 270NS
Re 270NS
cri Rat 1N52328
viDEO C_1
R22 1K
-5V
R23 +12v 160
ALL lOuH INDUCTORS RATED AT .9 OHMS D.C.EACH
PROJ. ENGS,? D.OTTO, J. JARON 'SOWG 1S CONFIDENTIAL PROPERTY OF MIOWAY MEG CO
- MIDWAY MFG. CO. FRANRLINPR IL GoIst _ABALCY CO. RGB INTERFACE Pc. [PART NO REVISIONS. SCHEMATIC A082-91363-B000 M05] -0.0.87-3 -B.030
DESIGNATION LIST
DESIGNATION NO, DESCRIPTION
RI-8 R9, 10,12 R13—20 R 2-29 R30
vl,2 u3 ua us ue u7 us us ulo vil viz uts ula vis ule viz vis vig u20 vai u22 u23 u24 u2s5 U26 var vee u29 u30 ust u32 U 33,34 U 35 u 36 u37 uv 38 u39 u40 ua uae u 43
DMHI, OMH2 33pf AX. CER. 1000pf AX, CER. 15 uf AX. TANT. O.l uf AX. CER. 100 ohm 1/4W 5% CARBON 10K 1/4W 5% CARBON 6.2K 1/4 W 5% CARBON 10K 1/4W 5% CARBON 2.7K i/4W 5% CARBON
4068 4572 4555 74LSI6! T4LS04 4516 74LS257 4516 T4LSI75 T4LS367 74LS00 74LS74 4572 4013 4516 T4LS257 4516 T4Lsi75 T4LS367 4lT4 T4LSI57 4539 408l
T4LS257 4516
4008 4175 4516 4175 4516 T4LS2s7 4516 4175 4008 4175, 4516 4175 4516 T4LS04
P.C. BOARD EXTRACTOR R21
COMP. SIDE. i
PROJ. ENG, JOHN JARON /D.OTTO DESCRIPTION
33 pf AX. CER. 1000 pf AX. CER. O.l uf AX. CER. IS af AX. CER.
100 OHM I/4w 5% CRBN
| anK" | os | "a | |
| ea" | " | " | # |
| lock | " | * | "oe |
T4LST74 T4LSI57 T4LSIGI TALSI75 74Ls257 T4LS367 P.C. BOARD EXTRACTOR
PATTERN BOARD
PER CROSS_REFENCE LIST
= KS
rx}
Bo Vw
- wNyaen-- Hw NT DESIGNATION NO.
cl c2 cPi-9 c3
RI-RS R30 RI3-R20 R9,RIO,RI2,R2I-R29
U29,U38 ul Ul,U2 u24 u2t U28,U30,U32,U37,U39,U41 U7,U9,UI6, UI8,U25,U27, U31,U33,U34,U36,U40,U42 ues Ud U3,UI4 ula U6,U43 us. v22 us Ul0,UIS U8,UI7,U26,U35 UH,U20 OMHI,OMH2
MIDWAY MFG. CO.
FRANKLINPK. ILL
Dim TOLERANCES
URED oon fears 378/82 ASSY DRAWING PATTERN BD AQ82-91355-CO00 IMO51 -00789-COlI5 PART NO.
0789- 00800-1600 0789- 00800-0700 0789-00800- 0800 0174 ~ 20704 -EXGX
0062-110B3-1 XXX 0062-199B3-IXXX 0062-217B3-IXXX 0062-227B3-IXXX
0789-00803-2000 0789- 00803-2100 0789-00803 -2300 0789-00803-2400 0789-00803- 2500 0789-00803-2600 0789-00803-2700
0789-00803-2800 0789 -00803-1700 0789-00803- 2900 0789-00803-3000 0789-00803-3100 0789-00803- 3400 0789-00803-1800 0789-00803 -1900 0789-00803-2200 0789-00803- 3200 0789-00803-3300 0789-00806 -0200
A080-91355-C000
or A Tese87 Bm o Aa B16 [= Ve Le] #2 t's Ae 1 ui , ul7 fy
747 7a.s367 apy! ‘el cad ete low
Jp a tT BI
Fae?
es
fee
DIM, TOLERANCES UNLESS SPECIFIED
CONCENTRICITY THR 003) + 1/6a[CKO
+.002- o0o/ DATE 03/16/82 nasa TALSI7S “> jss7° a f “> 3 rg be [ cad a bef ke
74Ls367
MIDWAY MFG. CO.
FRANKLIN PK. ILL.
PATTERN BOARD
SCHEMATIC A082-91355-CO0O O51 -00789-CO!I4 9-17
DESIGNATION LIST
DESIGNATION
Cl— c22 C26, C27 cae €29,C30 C31,c32 c33 C34
cPI— cPIO
RI—R2t R22—R27 R28,R29 R30—R46 R49 R50 RSI R52 R53 RS4 RSS RSE R57 RS8,R59 REO, REI R62—R74 R75,R76 R77—R80 R8I R82 R83 Re4
DI—03
Qt— Q3 Q4— 10 Qu, Qi2 os aK
vi v2 U3—U6 U7, U8
ICSU7, ICSUB
swi
QiMH—Q3MH
DMHI,DMH2
Jwi Jl J2AND JS
9-18 DESCRIPTION
0.1 MF AX. CER O.1 MF" a 1S MF AX. TANT O.IMF AX.CER. 15 MF AX. TANT O.1MF AX. CER. 1S MF AX. TANT
O.1MF AX. CER.
220 onM a0 5% CREN 2.7K
| 330 | * | " | 8 | 8 |
| 27k" | " | "os | ||
| too | * | * | ||
| 2oK | " | " | «4 | |
| 330 | " | " | "4 | * |
| loo | Oo" | "OHH | ||
| eek" | " | "4 | ||
| 330 | " | " | "4 | |
| 100 | wow | woe | ||
| 22k" | " | 4s | ||
| 330 | " | "7 | " | 4 |
| 22k | " | " | " | # |
| too | Oo" | "ON |
27k" "oe
| a7nk | oo | Oh | ||
| tok | " | "= | oe | 8 |
| ek“ | "= | 8 | 8 | |
| too | “ | ™ | *# | # |
| sik | "#8 | oH | ||
| a7" | * | " | # |
IN4004 DIODE
TIP HO 2N4401 2N4403 2N6427 2N4401
4099 74aLss6 45398 1448 CUSTOM 1/0
40 PIN IC SOCKET
SPOS DIP SWITCH
METAL SNAP
P.C BOARD EXTRACTOR
ZERO OHM 22AWG 24PIN CONK. 24PIN CONN. a ENG: J. JARON/D.OTTO [conorscatcows | NOT SCALE DWG Dom TOLERANCES CROSS REFERENCE LIST
DESCRIPTION
0.1 MF AX.CER.
18 MF AX. TANT
100 OHM bial 5% CRON 220 "
| 330 | " | " | ™ | # |
| eo" | * | 8 | 8 | |
| 27k * | “* | ue |
5.1K OK 22k
| a7kK | oo" | "8 | o |
1N4004 DIODE
TIPHO 2N4401 2N4403 2N6427
1448 CusTOM 1/0 74LS86 40399 45398
40 PIN ICSOCKET
8 POS DIP SWITCH
MOUNTING HARDWARE METAL SNAP
P.C BOARD EXTRACTOR ZERO OHM 22AWG
24 PIN CONN. 24 PIN CONN.
GAME BOARD ay
po a- guane
o
—wow
aT TN
---n
useoON ROTO DESIGNATION
Cl-C22,C26,C27,C29 C30,C33,CPI-CPIO C28,C3!,C32,C34
R49,R52,R55,RG6O,REI,RE2Z RI- R2t R26,R29,R51,R54, RST R5O,R53,R56,R58,R59 R22-R27,R30 -R48, RE2-RT4, Req R83 R77-R60 RSI R7S,R76
DI-03
Ql-a3 04-00 214 Qu,Ql2 Qs
U7,U8 u2 Ul U3-U6
Icsu7,icCsus
swi
QIMH-Q3MH
OMH!, DMH2 Jw
Jt v2 AND US
FRANKLIN PK. ILL MIDWAY MFG. CO. PART_NO.
0630-00800-0100
0530-00800-0200
0062-11083 -1XXX 0062-133B3 - IXXX 0062-144B3- IXXX 0062-195B3-1 XXX 0062-19983- IXxx
0062-21383 - 1XXXx 0062-227B3- IXxXx 0062-243B3- IXXXx 0062-259B3- IXxx
0530-0080!-0100
0530- 00802-0100 0530-00802-0200 . $870-99 802-0300 30-00 802-0400
0530-00803-0100 0530-00803 -0200 0530 -00803-0300 0530-00803-0400
0530-00804-0200
0530-00804- 0100
0017 - 00007-0134
0789-00806 -0200 0069-231XX- XBKX
0530-00804-0700 0530-00804 -0600
A080-90708-A530
ASS'Y DRAWING ROTO GAME BOARD A082-90708-A530 MO51-00530-A005
XASANASY aoe LLLILLLLLL PLL LT LILI L LLL L LLL LLL ELLIE IP)
- 2700
Cae Z W ; | eee eeraa—z Vy) s ne ye 7 —
J2 y a an LVL JULIA At PETTUTDITITET ITT te : + Gnome 5
am . d ; , : 7HLSe6
a . GAI BOARD _ies1-00880 008 A082-90708-A530 9-19