Regulus
Regulus (315-5033, Rev A.) (Sega, 1983) · Document · 19 pages · 33 sections · original scan
TECHNICAL MANUAL
CONVERSION KIT
72-393500
PART NO. 28-081300
WIC@a ‘THE - SOURCE:
WICO CORPORATION @ 6400 Gross Point Road @ Niles, IL 60648 @ Phone: (312) 647-7500
CONVERSION KIT PARTS LIST
REGULUS CONVERSION KIT PARTS LIST
72-393500
QTy DESCRIPTION PART NO.
| 1 | PC. Board | 23-521600 |
| 1 | PC. Board R.F. Cage (top) | 55-169600 |
| 1 | PC. Board R.F. Cage (bottom) | 55-169700 |
| 1 | Graphics Package Ass’t (marquee, control panel & cabinet sides) | 26-329800 |
| 1 | Power Grip Control | 98-001204 |
| 2 | Pushbuttons Long-(white) | 15-921001 |
| 2 | Pushbutton Holders & Switches | 15-098101 |
| 2 | PAL Nuts | 19-025400 |
| 1 | Cable Ass’t | 97-006400 |
| 1 | Installation Manual | 28-081300 |
| 2 | #6 x %" Round Head Phillips Sheet Metal Screws | 30-156900 |
| 4 | #6 x 1” Pan Head Phillips Sheet Metal Screws | 30-161300 |
| 1 | #6 x %” Oval Head Phillips Sheet Metal Screws | 30-158800 |
| 8 | #10-24 x 4" Carriage Bolt | 30-220200 |
| 8 | Washers, flat | 30-178600 |
| 8 | Hex Nut. 10-24 | 30-123300 |
| 1 | Momentary Switch (self-test) | 23-135600 |
NEVER replace any components with anything other than exact replacement parts.
NEVER remove circuit board connections while power is on.
DO NOT replace fuses with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing fuses with a higher value can cause severe damage to internal components if an overload occurs.
ALWAYS consult this manual before attempting repair or replacement of components.
USER INFORMATION
The P.C. Board Cage supplied with this Conversion Kit must be utilized and terminated to ground at the time of installation.
This is to avoid radio frequency radiation and comply with the limits for a Class “A” computing device pursuant to Sub-Part “J” of Part 15 of F.C.C. Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference — in which case the user, at his 1 own expense, will be required to take whatever measures may be required to correct the interference.
INTRODUCTION
This manual will provide you with adequate information to convert your old game as simply and as quickly as possible. For proper conversion the existing game monitor must be VERTICAL mounted; be RGB Raster Scan; have provisions for negative composite sync.
This manual is intended for the use of SERVICE TECHNICIANS who possess a general working knowledge of solid-state circuitry and video monitor theory. Anyone NOT knowledgeable in these areas SHOULD NOT attempt to mount this conversion kit.
To install this kit you will need the following tools: Large Drill Bits Channel-Lock Pliers Counterbore Bit X-Acto Knife
Adjustable Hole Cutter Tape Measure Power Drill Diagonal Pliers Nut Drivers Soldering Iron, Solder, etc
Nut Drivers Soldering Iron, Solder, etc.
Suggested order of game modification:
- Disconnect power from game.
- Remove present game boards.
- Remove all cabling to control panel (check game schematic).
- Remove old logic cards.
- Remove control panel, old pushbuttons and controls. Mount new pushbuttons, joystick and control panel cover.
- Mount new P.C. board cage and P.C. board.
- Wire coin door, monitor plug, power supply, control panel and speakers.
CABINET PREPARATION HINTS:
1. Old stick-on graphics can be removed with the aid of a hair dryer. The heat will “rubberize” the adhesive so most of the material will peel off. A mild solvent may be used to remove any remaining adhesive. A local paint dealer can recommend
one. (CAUTION: ALWAYS USE A PAINT SOLVENT IN A WELL VENTILATED AREA.)
If the cabinet has screened on or stencil graphics, the sides may be sprayed with the basic cabinet color. A light sanding and washing with a mild detergent should prepare the surface for spraying. (CAUTION: YOU CAN SPRAY ENAMEL OVER A LACQUER FINISH, BUT YOU CANNOT SPRAY A LACQUER OVER ENAMEL, DO THE SPRAYING IN A WELL
VENTILATED AREA.)
.. The decals supplied with your kit will be easier to apply and bond better if you; spray the area where the decal is to applied with windex or other brand of liquid window cleaner. Remove the decal backing and place the decal in position. If enough window cleaner is used you can slide the decal slightly to position it properly. Use a damp soft sponge, begin at the center and work toward the edges to remove any bubbles behind the decal. If any small bubbles remain, pierce them with a needle and press down on the area with the sponge. Be sure to work out all the excess liquid from behind the decal. The decal should dry for 24 hours.
CONTROL PANEL LAYOUT
CONTROL PANEL SECURING
30-220200 #10-24 x 1%" LG Carriage Bolt
bolts to secure Use the four #10 carriage CONTROL PANEL PLASTIC to cabinet.
POWER GRIP MOUNTING
Drill present CONTROL PANEL as shown below.
5/8” DIA. x 1/16” DEEP
° ; iA POWER GRIP ASS'Y. ° ! 2-9/16" ra 1
EXISTING CONTROL PANEL CARRIAGE BOLTS 4 |
Connect LEADS as follows: GREEN to GROUND BLUE is TRIGGER to IP FIRE: Yellow/Red = z YELLOW & ORANGE both go to IP BOMB: Yellow/Blue =04— NUTS
BASE ASS'Y.
SHAFT WASHER ———» ===>
Lock NUT ————> @&p
Make sure 5/8” Dia. counterbores are only 1/16” deep, so that SHIELD WASHER has room to move between bottom of CONTROL PANEL and top of BASE ASS’Y.
Feed POWER GRIP LEADS thru BASE ASS'Y. & insert POWER GRIP into BASE ASS'Y.
Slip SHAFT WASHER over end of SHAFT and screw on LOCK NUT
P.C. BOARD MOUNTING
P.C. BOARD CASE (Top) 55-169600 SHEET METAL SCREW 30-161200
PHILLIPSHEAD ——¥ MACHINE SCREW
(=) PRINTED CIRCUIT BOARD
P.C. BOARD CASE
PLASTIC SPACER =)
(BOTTOM) 55-169700
PLASTIC —> MOUNTING FOOT \
Cay
P.C. BOARD FOOT MOUNTING
»
BLACK LEADS OF CONNECTOR THIS END OF BOARD
ee WOOD SCREWS 30-313600
WOOD SCREWS se
30-313500
I*#— pc. Board
23-521600
A. Mount P.C. Board Case (bottom) tocabinet using two #6 x 3%" pan head Phillips wood screws 30-313500.
B. Mount P.C. Board Set into P.C. Board Case (bottom) 55-169700 using four #6 x 1” pan head Phillips wood screws 30-313600.
C. Slip bottom edge of P.C. Board Case (top) 55-169600 under bottom lip of P.C. Board Case (bottom) 55-169700 , use one #6 x 3%” pan head Phillips sheet metal screw 30-161200, to secure.
. This unit may be mounted either vertically or horizontally, depending on the availability of space in your game cabinet.
EDGE-CONNECTOR “PIN-OUTS”
COIN - CREDIT OPTION SWITCH DIP SWITCH A Ee ee ee
| fico | icrepiT | | or | orr | orF | orr [ore | ore | orr | orF | |
[icon 2CREDITS |
| Hcon | a crepTs | Star a ry a a ta | COMPONENTSIDE | SOLDER SIDE |
| jicon | acreoits | on Ton | ofr | orr | on [on | ore [FF | | MON. GND. [14 | 18 9 GND. | ||
| [icon screpits | oF | orr | on | orr | orr | ofr | on | oFF | | MON. BLUE | SYNC | ||
| ficoin | screpits | on | orr | on | or] on | orF | on | oFF | | MON. RED | MON. GRN. | |
| |2cows screpit | | orr | on | on | ofr | ofr | on | on | oF | | SPKR. | SPKR. | |
| |.3coins | crept | J on | on | on [oF | on | on | ON | oFF | | SERV. SW. | |
| Jacoins icreor | | orr | ore] orr] on [ore | ore | orr [on | | TEST SW. | ||
| [2cons scares | on | orr | orF] on [on Lorre] orr [on J | comnsw. 2 | 2P START |
COIN Sw. 1 1P START
EEC 1P RIGHT 2P RIGHT
| BEEEEEE | mn | 00 |
| scons scneors | | 1P DOWN | 2P DOWN |
| P2coms —roneorT | | 1P FIRE | 2P FIRE |
| BESSSo0 | meg: | ba |
| [icon | 1cREDT | | +12V |
COIN METER 1 COIN METER 2
| P3CcOINS 3CREDITS | | +5V | +5V |
+5V +5V scons _scnenis | | SCOINS GCREDITS _| GND, [[ 21A] 2189 GNb. 1 pon er 1 CREDIT GND. [[ 22A]} 228i GND. | 4COINS _SCREDITS _| ae 5 CREDITS 1COIN 1CREDIT 2COINS _ 3CREDITS
- [TCOIN2CREDITS | SCOINS 6 a 4COINS 8 (a SCOINS 11 CREDITS COIN SWITCH 1 COIN SWITCH 2
OPTION SWITCH SETTINGS DIP SWITCH B ee Cae COCKTAIL UPRIGHT orr | oFF PLAYERS 4 NOT] on | oFF
SHIPS 5 USED] OFF bei USED
GAME EASY DIFFICULTY HARD GAME CONTINUE GAME END
GAME BOARD
; 2 Tene ) = ee i ae i = nines ree SESE om om om om 2125] = ee) Sow] Se] ee) Sew] Fer) a = —— rem] Sen] re]
Scise)] Geen een fen pen ea eee eicer) Cae) Satsso= Cicisa] Pict4o] Piciz4) Gicwz9] Fici6)
REGULUS
REVISED GAME BOARD PARTS LIST
1C1: Z80A 1C2: TMM2009P-B IC3: EPROM 5652 1C4,5: 76489 IC6: 74L$138 IC7: LA4460 1€8,9: 74LS174 (C10: 7404 1C11: 74L$132 1C12: 74L$109 1013: 74/125 1C20: 74LS107 1C21: 8255 1C22,23: 74/8244 1624: AM25LS2519PC 1C25,26,27,28,29: 74L$399 1C30: 74LS273 131: 74LS155, 1C38: 74LS257 1C39: 74LS157 1C40,41,42: MBM2148L-55 143,44: 74L$157 iC45,46: CUSTOM PAL 16R4 (047,48: 74LS157 1C49: 748164 1C51: 7418257 152: 74LS32 1C53,54,55: MBM2148L-55 156,57: 74LS157 1C58,59: 74LS669 160,61: 74LS157 162: 748201 1C63: EPROM 5646 1C64: EPROM 5648 IC65: EPROM 5650 1067: 748175 IC6B: 74LS273 169: 74LS 157 1C70: 7425 1C71: 74L8174 1C72: 74L$20 1C73,74,75,76: 74LS669 1C77: 74LS157 (C78: MBM2147E 1C79: 74LS04 1C80: EPROM 5647 1C81: EPROM 5649 1C82: EPROM 5651 1C84: 74L$107 IC85: 74LS139 1C86: EPROM 5638 1c88: 74LS85 189,90: 74LS157 192: 74L8123 1C93: EPROM 5639 IC95: 74LS04 1C97: CUSTOM 315-5011 ic98: 74LS283 IC99: 74LS 157 1€100: 74157 16 101,102: MB8128-15 1C103,104: 74L$273 1C105: 74LS377 1106: PROM 5317 1€107: 74LS138 1€ 108,109: 74LS245 1C110: PROM 315-5012 1C111: 74LS283 1€112,113: 74LS157 10 114,115: 74LS245 1C116: 74LS273 1117: 74LS368 1118: 74LS155 1119: 74LS100 1C120: 74LS27 1121: 74LS153 1C 122: 74LS174 1C 123: 74LS153 1C124: 74LS157 1125: Z80A 1C 126: 74LS245 1C 127,128: 74LS244 1C129: EPROM 5950 1C130: EPROM 5951 1131: EPROM 5952 1C 132: EPROM 5953 1C133: EPROM 5954 1C134: EPROM 5955 1C135: TCSS33P-B 1C 137: 74LS153 1C 138: 74LS174 1€ 139,140: 74LS153 (C141: 74L8161 1142: 74804 1143: 74LS145 1150: 74LS245 1C151: MB8128-10 1C152: 748145 1153: 74S175 1154: 74LS32 1C 155: M54523 1C 156, 157,158: CUSTOM 315-5025, 1C159, 160,161,162: 2148L-55
REVISED PAGE 8
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
EPROM LOCATIONS
CUSTOM PROM
EPROMS
CUSTOM PROM p 5317]
CABLE HARNESS TERMINATIONS
BROWN/BLACK (-) BROWN/WHITE (+) SPEAKERS
YELLOW/BLACK (COIN SW.) BLACK (GND)
COIN DOOR
ee GRAY (SELF TEST SW.) BLACK (GND)
FED (+54) = ORANGE (+12) POWER SUPPLY
en BLACK (PWR SPLY GND)
—_— BLACK/WHITE (MON. GND)
BLUE/WHITE (MON. BLUE)
RED/WHITE (MON. RED) MONITOR —————— GREEN/WHITE (MON. GREEN)
ee WHITE (NEG. COMP. SYNC.)
BL Ack (GND) WHITE/BLUE (1P LEFT) J WHITE/GREEN (1P RIGHT) ————— WHITE/YELLOW (1P UP)
CONTROL
—_— WHITE/RED (1P DOWN) PANEL YELLOW/RED (1P FIRE) YELLOW/BLUE (1P BOMB)
- YELLOW/ORANGE (2P START)
- YELLOW/WHITE (1P START)
SELF—TEST
You have an optional SELF-TEST feature by wiring the 23-135600 MOMENTARY SWITCH to PIN 17 of the P.C. BOARD EDGE CONNECTOR and to GROUND.
To initiate the SELF-TEST, press the BUTTON. As you do, the games steps thru its SELF-TEST.
1ST: RAM TEST
2ND: ROM TEST
3RD: INPUT TEST (push all CONTROL PANEL and POWER GRIP switches game will indicate if they are functioning). GAME will indicate DIP SWITCH settings.
4TH: SOUND TEST (Push 1 or 2 PLAYER BUTTON, GAME will step thru all the GAME SOUNDS).
5TH: MONITOR ADJUSTMENT (screen shows COLOR BARS, GREY BARS and WHITE FRAME, for CONVERGENCE ALIGNMENT and CENTERING OF PICTURE
6TH: Returns to GAME ATTARCT MODE.
€ LAAHS SILVINSHOS LIM NOISHSANODS SN1NDAY
3s Hos 7 7 : bia by werd 172s rd WET) 4 aM ot Lia WL mA T oA = g ANIN NOILO3AS
NOTES
Wica
‘THE SOURCE. 6400 W. GROSS POINT ROAD « NILES, ILLINOIS 60648
For Replacement Parts
cammeenaammene DISPLAY MONITORS GO7 SERIES 13” & 19” R.G.B. COLOR
The GO7 Series of Color Display Monitors is available with precision in-line 13-inch and 19-inch CRT formats. Each is designed to meet the high reliability and performance standards common to the video games industry. HORIZONTAL MOUNTING ONLY Ref. No. Description Wico No. 38-GO7-902-00 13° R.G.B. Color 36-0123 38-GO7-904-00 19" R.G.B. Color 36-0124
wien. peore
ISOLATION TRANSFORMER
Isolates monitor from AC line to reduce shock hazard. Protects equipment.
Input Volts: 115VAG
Output Volts: 115VAC. 150 VA Rated. 2 Primary & 2 Secondary wire leads, 642" long. Mounting Centers: 3-1/8" x 2-3/4" Four Mounting Slots: 7/32" x 3/87 Vy Wico No. 22-1022
3-OUTPUT SWITCHING D.C. POWER SUPPLY
3-Output Switch-Mode D.C. Power Supply Designed for Video Game/Microprocessor +5V/5A (Max. 7A), ~5V/1A, +12W/1A. Input A.C. Voltage 90-130VAC e@ UL. Listed © Steps down AC voltage from 110V to operate within specified range. @ High Efficiency/Low Cost ¢ Latest PWM IC regulated design. © Fully enclosed packaging — All aluminum cover. © Soft-start. @ Foldback current limit on SV main output. © Auxiliary output short-circuit protection. © 4hours burn-in. © Compact & lightweight: Mounting centers 72” approx. size 47"H x 7%"W x 1-13/16"D (plus Mounting Bracket). Wt. 1 lb. 6 oz. Wico No. 27-6110
WICO’S GOT IT ALL!
(All the parts you need, anytime you need them.)
wica. ‘THE SOURCE:
This equipment complies with the requirements in Part 15 of FCC Rules for a Class A computing device. Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the Operator to take whatever steps are necessary to correct the interference. FORMNO. P84-0619
es ee ee +
aie no. 20 S600 enn