CATHODE RAY TOMES

Mortal Kombat 3 Operation Manual (16-40039-101 Mar 1995)

Mortal Kombat 3 (rev 2.1) (Midway, 1994) · Document · 42 pages · 28 sections · original scan

Page 1

MARCH 1995 G MIDWAY 16-40039-101

MORTAL KOMBAT

OPERATION MANUAL

Operation & Adjustments * Testing & Problem Diagnosis

& Parts Information ¢ Wiring Diagrams

Page 2

MORTAL KOMBAT

INSTRUCTIONS

Insert Coin(s). In a two player game, the loser pays and the winner stays. Press the Punch and Kick buttons to attack an opponent. Press the Run button to make your on-screen character run.

Use the joystick to make the on-screen character jump, duck,

move left, and move right.

Use different joystick and button combinations to discover

secret moves.

Page 3

MORTAL KOMBAT

AORTA Poway,

Information current at time of release.

MIDWAY Manufacturing Company reserves the rights to make modifications and improvements to its products. The specifications and parts identified in this manual are subject to change without notice.

Page 4

TABLE OF CONTENTS

Section One - Operation and Troubleshooting Safety Notices...

Servicing... Game Features.. Starting-up....

Control Panel Diagrai Game Operation... Control Switches. Control Switch Location Menu System Operation Operation. Main Menu Diagnostic Test. Switch Test DIP Switch Table and Test. CPU and Sound Board Te: Monitor Patterns and Burn-i Coin Bookkeeping. Game Audits... Game Adjustment

Custom Pricing Tabi

Troubleshooting...

Section Two - Parts Information Cabinet Hardware, Electronics, Monitor, and Manuals...... Control Panel, Fluorescent Lamp Assembly, Speaker, Transformer Assembly, and Cables.

Power Supply...

Section Three - Cabinet Wiri

Ig Power Wiring and Transformer Diagrat Cabinet Wiring Diagram.............8

© Copyright 1995 MIDWAY Manufacturing Company

Page 5

MORTAL KOMBAT

MOIR TAIN RE,

SECTION

ONE

OPERATION

Page 6

SAFETY NOTICES The following safety instructions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play.

JN CAUTION

AC POWER CONNECTION. Before connecting the game to the AC power source, verify the Voltage Selection Chart jumper wires are installed correctly for the line voltage in your area. For details refer to Section 3.

PROPERLY GROUND THE GAME. To avoid electrical shocks, do not plug in the game until it has been inspected and properly grounded. MIDWAY games should only be plugged into a grounded 3-wire outlet.

NOTE: The control panel is removable. Ensure that the ground braid is securely attached to the control panel after servicing.

DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game.

USE THE PROPER FUSES. To avoid electrical shock, replacement fuses must match the original fuses in fuse type, voltage rating, and current rating.

MONITOR PRECAUTIONS. When removing or repairing the monitor, extra precautions must be taken to avoid electrical shock because high voltages may exist within the monitor circuitry and cathode ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the monitor with you hands or metal objects! Always discharge the CRT by the following method: Attach one end of a large, well-insulated, 20kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.

HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

!! ATTENTION !!

PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board (PCB) are properly connected. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. All connectors are keyed to fit specific pins on each board.

Page 7

SETUP PROCEDURE

INSTALLATION & INSPECTION

Game Location Power Temperature Humidity

Requirements 100VAC @ 50Hz 3.0 Amps 32°F to 100°F Not to exceed 120VAC @ 60Hz 3.0 Amps (0°C to 38°C) 95% relative 230VAC @ 50Hz 2.0 Amps Cabinet Statistics | Dimensions Weight

10. Width 27° - Depth 41" - Height 73" Approximately 369Lbs

Remove all items from the shipping containers and set them aside. Inspect the exterior of the cabinet and the control panel for any damage.

The keys for the coin door and the rear door are attached to one of the joysticks. Unlock and open the coin and cash box doors. Remove the spare parts stored in the cash box.

Remove the screws holding the rear door then unlock and remove the door. Inspect the cabinet interior for any signs of damage. Check all major assemblies to assure that they are mounted securely.

Refer to the Cabinet Wiring Diagram (Section 3), and check to see that all cable connectors are correctly secured. Do not force connectors. Watch for damaged connectors and avoid making reversed connections.

If a padlock is desired, turn the rear door hasp so that it protrudes from the hole in the back of the cabinet. Remove the two nuts inside the cabinet, at the top and middle of the rear door opening. Then slide the hasp off of the bolts. Turn the hasp, slide it back on the bolts and replace the nuts.

Next, locate the four leg levelers among the spare parts in the cash box. There are four threaded holes on the bottom of the cabinet; one in each corner. Place one leg leveler (with its hex nut) in each of the threaded holes. Lower each leg leveler until the cabinet is stable and level.

!! WARNING !! The cabinet is top heavy.

Determine the value of your line voltage with a meter. Then, check the jumper wires to the main power supply transformer. Be sure it is jumpered to correspond to your local line voltage value. If necessary, change the jumper wires to the transformer in accordance with the Voltage Selection Chart in Section 3.

Replace the rear door and screw (lock) it securely. NOTICE: Tamper proof screws are included in the spare parts bag. These screws are optional and may be used to secure the rear door panel. The T20 wrench is used for the installation of these screws. Close and lock the front coin and cash box doors.

To attach the line cord, remove the four Phillips-head screws that mount the line cord cover plate to the rear of the cabinet. Match the prongs on the plug with the holes in the receptacle and push the line cord securely into place. Make sure the cord aligns with the indentation of the plate, (indentation should point toward the bottom of the cabinet). Remount the line cord cover plate.

Plug the game into a grounded (3-terminal) AC wall outlet. Switch ON the game, using the ON/OFF switch located on the upper left rear of the cabinet.

Page 8

CABINET ASSEMBLY Front View

FLUORESCENT BULB

MARQUEE \ | a

SPEAKER

25" “fh BEZEL r

BUTTONS ia COIN DOOR ¢@

CASH BOX DOOR ce

@

1-4

Page 9

CABINET ASSEMBLY Rear View

ON/OFF SWITCH

b

VENT COVER —— —

CPU/SOUND BOARD

SWITCHER POWER SUPPLY a) fey @o SH)

SH J S>

REAR DOOR POWER PACK ASSEMBLY

LINE CORD

Page 10

SERVICING

@ Servicing the Control Panel Switch off power to the game and open the coin door. The control panel is held in place by two latches (located inside the cabinet) which provide constant pressure on the strikes. To release the latches, reach through the coin door opening toward the right and left sides of the cabinet. Do not reach straight back through the coin door or you could damage the monitor control board. Lift the latch handle and unhook the wire fasteners. Grip the joysticks and carefully tilt the contro! panel back on its hinge.

To return the control panel to its normal position, carefully lean it forward until it rests on the cabinet. Be careful not to let the control panel slam down onto the cabinet, or to pinch any wires. Always reclasp the latches.

@ Removal of the Viewing Glass Switch off power to the game and open the control panel. Remove the five hex-head screws and the black metal strip at the bottom of the viewing glass. Carefully, slide the glass from the side grooves and lift it clear of the cabinet.

¢@ Removal of the Monitor Bezel Switch off power to the game. Open the control panel and remove the viewing glass. Lift the bezel off of the monitor.

@ Monitor Replacement We recommend that you read the SAFETY NOTICES section thoroughly before beginning this procedure. Switch off power to the game. Remove the viewing glass and the monitor bezel. Completely disconnect the monitor from all of its cabling. Remove the four flange nuts securing the monitor's mounting flanges to its mounting panel. Pull the monitor carefully from the cabinet.

AN CAUTION

The monitor does not require an isolation transformer. However, when servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM LINE VOLTAGE WITH AN ISOLATION TRANSFORMER. THE MONITOR IS HEAVY. BE SURE IT IS FIRMLY SUPPORTED IF IT MUST BE REMOVED FROM THE CABINET.

@ Removal of the Marquee Switch off power to the game. Remove the hex-head screws from the black marquee retaining strip {ocated on top of the header. Remove the strip and carefully lift the marquee and the marquee glass from the top of the header. Store the marquee carefully to prevent damage.

Page 11

@ Removal of the Fluorescent Light Assembly Switch off power to the game. Remove the marquee glass and the marquee. The fluorescent bulb is now accessible for replacement. Remove the plastic lamp locks. Grasp the bulb, give it a quarter turn, and remove it from its socket. Carefully, place a new bulb into the socket, and turn to reinstall.

To remove the entire light fixture, disconnect the fluorescent light assembly from its power cable. Remove the screws that hold the assembly to the cabinet then lift out the assembly.

!! WARNING !! If you drop a fluorescent tube and it breaks, it will implode! Use care in handling.

@ Removal of the Speakers Switch off power to the game. Remove the marquee and the marquee glass. The speakers come out from the front of the cabinet. Be sure to disconnect the cabling and remove the nuts on the mounting screws before attempting to remove the speakers from the enclosure. Carefully, reinstall the seals upon completing any task in the speaker enclosure.

# Volume Control, Begin Test Switch, and Service Credit Switch Open the coin door. The game's volume control and diagnostic push-button switches are located on a small bracket on the door. The volume is controlled by the two center buttons. Press the Volume Up or the Volume Down button until the desired sound level is reached. The Begin Test switch, on the right, activates the game's menu system. The Service Credit switch, on the left, allows credits to be allotted for service testing without affecting the game's bookkeeping total.

SERVICEVOLUMEVOLUME,gECIN
REDSDOWNuPTEST
o4)ENTERSLAM TILT

1-7

Page 12

GAME FEATURES

STARTING UP Switch on power to the game. A "rug" pattern appears on the screen. When the "rug" pattern ends, the screen shows Checking Scratch RAMS, then Checking ROMS. (Refer to page 2-5 for proper chip location.) The next screen shows the revision level, the CMOS test results, and the coin setting. The game goes into the Attract Mode.

Insert the desired amount of coins, bills or tokens. Select which player receives the credit by pressing the appropriate Start button. Use the joysticks to select an on-screen character, and any control panel button to confirm your choice. Game play starts automatically once the on-screen characters are chosen.

NOTE When an error is detected during the Start-up tests, game start-up does not progress, and an error message appears on the screen.

PLAYER CONTROLS ¢@ Start Button Each player has a Start button. The Start buttons allow one or two players to begin or continue play.

@ Joysticks Each player has a joystick which he uses to control an on-screen character. The player can make the on-screen character move, jump or duck.

@ High Kick/High Punch Buttons These buttons allow the on-screen character to kick or punch an opponent in the upper body.

«@ Low Kick/Low Punch Buttons These buttons allow the on-screen character to kick or punch an opponent in the lower body.

«@ Block Buttons These buttons allow the on-screen character to block an opponent's punch, kick, or special move.

«@ Run Buttons These buttons speed up the on-screen character.

NOTE Use joystick and button combinations to discover secret moves.

sume wow uP Fup FUP | fuP

HoHHoHMicaHoH
PUNCHKICKPUNCHfick

ae wet © x © “we a © «x © O . O20 020

buckLowLowucLowtow

(©) PUNCH iow © PUNCH kex

Control Panel

1-8

Page 13

GAME OPERATION The MORTAL KOMBAT 3 Contro! switches are located on a bracket, inside the coin door.

CONTROL SWITCHES

@ Slam Tilt Switch The Slam Tilt switch prevents pounding for free games.

@ Volume Down/Volume Up Buttons The Volume Down and Volume Up push-button switches increase or decrease the volume level of the music and speech. The volume level can be adjusted during the Attract Mode or during menu system operation. For greater profits, set your game's volume level at a nice loud setting.

@ Begin Test Button The Begin Test push-button switch enters the game's menu system. Press the Begin Test switch to access any of the menu system functions.

@ Service Credit Button The Service Credit push-button switch is a special feature switch that allots credit without affecting the game's bookkeeping total.

NOTE The coin door must be open for the control switches to work.

seavice ME VOLUME uP’ vou cREOTS own OO

ra o SLAM TILT

Control Panel Switch Locations

Page 14

MENU SYSTEM OPERATION

OPERATION All game audits, adjustments and diagnostics are options of the Main Menu. Each option, in turn, has its own menu that lists several choices which you may act upon as desired.

Press the Begin Test switch on the coin door to open the Main Menu (shown below). Game adjustments, bookkeeping and diagnostics are all accessible from this menu.

Use either joystick to move the cursor up and down the menu screen. Notice that the options are highlighted in sequence. Press any button on the control panel to open a highlighted option.

NOTE Only highlighted options can be opened.

MAIN MENU

To exit the Main Menu and return to the Attract Mode, use either joystick to select EXIT TO GAME OVER and press any button.

Page 15

DIAGNOSTIC TESTS Use either joystick to select the Diagnostic Menu and any button to open it. Then, use either joystick to move the cursor up and down the menu and any button to open a highlighted option.

To exit the Diagnostic Menu, use either joystick to select RETURN TO MAIN MENU and press any button.

DIAGNOSTIC MENU

Switch Test The Switch Test allows the operator to test the switches on the control panel and in the coin door.

Use either joystick to highlight the Switch Test and any button to begin the test.

During the Switch Test the top of the screen shows the control panel switches while the bottom of the screen shows the coin door switches. Press a control panel or coin door switch and the switch location on the screen lights. Release the switch and the screen returns to normal.

O PuveR 9 START Pures 2 START

O_O O_O

O0°oO5°

To exit the Switch Test, press both Start buttons together.

QO oO ie)

OCOOOOOOO
contcon 2conscon +sencesueust

Oo OC FO OO

1-11

Page 16

DIP Switch Test The DIP Switch Test allows the operator to check or change the position of the DIP Switches on the CPU Board.

Use either joystick to select the DIP Switch Test. Press any button to access the DIP Switch Setting Tables. The screen displays the current settings. To change a setting, slide the switch to the desired position. Check the screen to verify the new setting. /n some cases, setting a function to OFF actually enables the function. For example, setting DIP Switch Coinage to Off enables DIP Switch Coinage.

Press any button to return to the Diagnostic Menu.

DIP Switch 1 Setting Table Sw.7 | SW.6 | SW.5 | SW.4 SW.2_ | SW.1 Coinage DIP Switch CMOS Coin Settings

USA1Ger. 1FreqOff*Off*
USA2Ger. 2Fr.2OnOff
USA3Ger. 3Fr.3OffOn
USA4Ger. 4Fr4OnOn
USAECAGer.ECAFr.ECA | OffOff
N/UN/UN/UOnOff
NUNUN/UOffOn
Free PlayFree PlayFree Play | OnOn

Country USA oft" Off*

Germany On Off

France Off On

Not Used On On 1 Count/Coin od

Totalizer On

Test Switch Game Mode Off Test Mode On

DIP Switch 2 Setting Table SW.7_ | SW.6 Violence On

Blood In Game

Not Used Off* On Attract Sounds On

Not Used

Dollar Bill Validator Not Installed

Installed On

Do Power Up Test Off* Skip Power Up Test On Not Used

  • Indicates factory setting.
Page 17

CPU Board Test The CPU Board Test, much like the Start-up Test, allows the operator to check the RAMS and the ROMS.

Select the CPU Board Test with either joystick. Press any button to start the test.

When this test is activated, a "rug" pattern appears on the screen. The screen then changes to show the layout of the RAMS and ROMS. A chip location that is shown as black with a white outline is used. A Chip location that is shown as gray with a white outline is not used. During the test, chips are good if they turn green and faulty if they turn red. Turn to page 2-5 for the exact chip location.

The test pauses if a faulty RAM or ROM is detected. Press any button to continue the test.

Sound Board Test This test allows the operator to listen to some of the sounds this game is capable of producing.

Use either joystick to select the test, then press any button to open the menu. The screen displays two test options. Use either joystick to select an option and any button to begin the test.

SOUND TEST MENU

GENERAL TEST analyzes the sound circuitry. The screen shows a list of etror codes. A successful test causes a single "tone" to sound. Detection of a fault causes a series of tones or no tone at all to sound. Press any button to return to the Sound Test Menu.

PLAY SOUNDS tests synthesized and digitized sounds from the CPU/Sound board. Advance to the next sound with any button. Use either joystick to end the test.

Select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU and press any button.

Page 18

Monitor Patterns The Monitor Patterns Test provides a menu for testing the monitor.

Select the test with either joystick. Press any button to open the test menu. Once the menu is open, use either joystick to select an option, and any button to begin it. Press any button again to return to the Monitor Patterns Menu.

MONITOR PATTERNS MENU

The RED, GREEN and BLUE SCREEN tests fill the screen with either red, green or blue. Press any button to return to the Monitor Patterns Menu.

The COLOR BARS test fills the screen with several shades of colors to help with red, green and blue level adjustments. Each color should appear sharp and clear. Press any button to return to the Monitor Patterns Menu.

The CROSSHATCH PATTERNS test fills the screen with a grid and a series of dots. The grid and the dots should be clear. The dots should be round. Press any button to return to the Monitor Patterns Menu.

If any of the tests show a need for adjustment, use the proper knobs on the Monitor Controls board. The Monitor Controls board is located just inside the control pane! opening, beneath the monitor.

To exit this test, use either joystick to select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU, then press any button.

Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Use this test to find intermittent CPU Board problems. The Audit Table specifies the number of Burn-in cycles that have been successfully completed.

Use either joystick to select the test, then press any button to activate it. When the Burn-in Test detects an error the test stops and an error message is displayed on the screen.

To exit this test, switch the game off, then on again.

Page 19

COIN BOOKKEEPING

The Coin Bookkeeping Table records the coin box totals and the game play counters.

Use either joystick to select the Coin Bookkeeping Menu, then press any button to open it.

COIN BOOKKEEPING TABLE

TOTAL COLLECTION TABLE

To exit Coin Bookkeeping, use either joystick to select RETURN TO MAIN MENU and press any button.

Page 20

GAME AUDITS Use joystick to select the Game Audits Menu, then press any button to open it. Page through the available audits by selecting NEXT AUDIT PAGE or LAST AUDIT PAGE. Select RETURN TO MAIN MENU and press any button to exit Game Audits. Game audits cannot be set. They can only be cleared.

PAGE 1 OF AUDIT TABLE

PAGE 2 OF AUDIT TABLE

1-16

Page 21

GAME ADJUSTMENTS The Game Adjustments allow the operator to customize the game.

Use either joystick to select the Game Adjustments Menu. Press any button to open the menu.

The Game Adjustments Menu offers several options. Each option has several choices. Use either joystick to select an option, then press any button to open the option. The next menu screen provides a setting value. Use either joystick to change the setting value and press any button to lock it in.

To exit the Adjustments Menu, use either joystick to select RETURN TO MAIN MENU, and press any button,

NOTE Adjustment values set by DIP SWITCH, override adjustment values set by the menu system.

GAME ADJUSTMENT MENU

Game Adjustments

Standard Pricing Standard pricing allow the operator to choose any of the "standard" selections from the Standard Pricing Table. See page 1-19.

Modify the setting value with either joystick. Press any button to lock in the new value and return to the Adjustments Menu.

Custom Multipliers Customize the internal coin chute multipliers for each chute.

Custom Pricing Custom pricing allows the operator to install pricing other than that of the Standard Pricing Table. Custom pricing also allows the operator to select the maximum amount of credits per game, the amount of credits required to start a game, and the amount of credits required to continue a game. This option is being adjusted from the DIP Switch settings. See page 1-20.

Modify the setting value with either joystick. Press any button to lock in a new value and return to the Adjustment Menu.

Page 22

Game Adjustments Continued...

Free Play This option selects free play. The setting choices for this adjustment are:

  • No
  • Yes
  • Factory Setting: No

Computer Difficulty This option determines how tough the computer opponents are. The setting choices for this adjustment are:

  • (1) Extra Easy
  • (2) Easy
  • (3) Medium
  • (4) Hard
  • (5) Extra Hard
  • Factory Setting: Medium
Page 23

STANDARD PRICING TABLE

Name Setting - Coin/Credit Coin 1 Coin 3 Coin 2 Coin 4 Bills

USA1V25¢(2 to Start, 2 to Continue) | 25¢25¢$1.00
USA21W25¢(2 to Start, 1 to Continue)| 25¢25¢$1.00
USA3125¢(1 to Start, 1 to Continue)25¢25¢$1.00
USA41/50¢, 3/$1.00(1 to Start, 1 to Continue)| 25¢25¢$1.00
USAS1/50¢, 4/$1.00(2 to Start, 1 to Continue)| 25¢25¢$1.00
USA61/50¢(1 to Start, 1 to Continue)25¢25¢$1.00
USA71/50¢, /$1.00(1 to Start, 1 toContinue) | 25¢25¢$1.00
USA81/50¢, 4/$1.00(2 to Start, 2 to Continue)25¢25¢$1.00
USA1/25¢(3 to Start, 2 to Continue)25¢25¢$1.00
USA 101/25¢(3 to Start, 3 to Continue)25¢25¢$1.00
USA ECA1/25¢, 4/$1.00(2 to Start, 2 to Continue)$1.0010¢25¢.Se.$1.00
German 11/1DM, 6/5DM1DM5DM
German 21/1DM, 7/5DM1DM5DM
German 31/1DM, 8/5DM10M5DM
German 41/1DM, 5/5DM1DM5DM
German 51/1DM, 6/5DM1DM5DM
German ECA1/1DM, 2/2DM, 6/50M.5DM1DM20M
France 12/5F, 5/10FSF10F
France 2205F, 4/10FSF10F
France 3SF, 3/1 0FSF10F
France 441V/SF, 2/10FSF10F
France 52/5F, S/10F, 11/2 x 10FSF10F
France 62/5F, 4/10F, 9/2 x 10F5F10F
France 74V/SF, 3/10F, 7/2 x 10FSF10F
France 81/5F, 2/10F, 5/2 x 10FSF10F
France 91/3 x 1F, 2/5F1FSF
France 1012 x 1F, 3/5F1FSF
France 111/3 x 1F, 2/5F, 5/2 x 5F1FSF
France 121/2 x 1F, 3/5F, 7/2 x 5F1FSF
France ECA1/3 x 1F, 2/5F, 5/2 x SFAF10F5F
Canada1/2 x 25¢, 3/$1.0025¢$1.00$1.00
‘Swiss 1AIF, 6/5F1FBF
Swiss 2AF, 7/5F1FSF
Swiss 3A/F, 8/5FIFSF
Ital1/500 lire500 lire500 lire
UK 1 ECA1/50P, 3/21£120P5OP10P
UK2ECA1/50P, 2/21£120P50P10P
UK 3ECA1/30P, 2/50P, 5/1£120PSOP10P
UK41/50P, 3/21£150P
UKS51/50P, 2/81£150P
‘Spain 11/100 peseta, 6/500 peseta100 peseta500 peseta
Spain 21/100 peseta, 5/500 peseta100 peseta500 peseta
Australia 11/3 x 20¢, 2/$1.0020¢$1.00
Australia 2145 x 20¢, 1/$1.0020¢$1.00
Japan 11/100 yen100 yen100 yen
Japan 22/100 yen100 yen.100 yen
Austria 15 schilling10 schilling
Austria 25 schilling10 schilling
Belgium 11/20F20F20F
Belgium 23/20F20F20F
Belgium 32/20F20F20F
Belgium ECA1/20F50FSF20F
Sweden1/3 x 1 krona , 2/5 krona1 krona5 krona
New Zealand 1 | 1/3 x 20¢20¢20¢
New Zealand2 | 1/2 x 20¢20¢20¢
Netherlands1/1 guilder, 3/2.5 guilder1 guilder2.5 guilder
Finland1/1 markkaA markka1 markka
Norway1/2 x1 krone, 3/5 x 1 kroneikrone1 krone
Denmark1/2 x 1 krone, 3/5 krone, 7/2 x 5 krone1 krone5 krone
Antilles1/25¢, 4/1 guilder25¢1 guilder
Hungat1/2 x 10 forint, 3/2 x 20 forint10 forint20 forint
Page 24

1)

2) CUSTOM PRICING

CUSTOM PRICING MENU

Coins inserted accumulate units. This adjustment specifies the number of units given for each coin in the fourth chute (see “Units/Credit*).

Coins inserted accumulate units. This adjustment specifies the number of units given for each bill validated (see “Units/Credits").

This is the number of coin units required to buy one credit.

There is one bonus credit awarded after this many coin units have accumulated.

This is the minimum number of units required before any credits are awarded.

Each player needs this many credits to begin a game.

Each player needs this many credits to continue a game.

The detailed bookkeeping screen shows total collection based on this many coins per dollar. (Set to Zero to disable the display of money totals.)

This is the limit for the credit counter. Additional coins inserted will be lost (factory setting: 30).

1-20

Page 25

UTILITIES The Utilities Menu allows the operator to clear the game's bookkeeping memory.

Use either joystick to select the Utilities Menu, then press any button.

Use either joystick to select a utility. Press any button to activate the selection.

UTILITIES MENU

Once the selection is made, a dialogue box appears, and the operator can choose to reset the utility.

For example:

CLEAR COIN COUNTERS? ARE YOU SURE?

YES NO

Use either joystick to choose a setting value. Press any button to lock in the new setting value.

To exit the Utilities Menu, use either joystick to select RETURN TO MAIN MENU, then press any button.

1-21

Page 26

HARDWARE INFO

The Hardware Information screen gives the date the game was manufactured and the game's serial number.

HARDWARE INFO MIDWAY MANUFACTURING COMPANY

WOLF UNIT

SERIAL NUMBER: XXXXXXXX

DATE OF MANUFACTURE: XX/KX/XXXX

Press any button to exit this screen and return to the Main Menu.

Page 27

VOLUME ADJUST The Volume Adjust feature allows the operator to determine the sound and music level of the game.

The volume level can be adjusted from either the Attract Mode or the Menu System. Press the Volume Up button to raise the volume level and the Volume Down button to lower the volume level. Either joystick can also be used to raise or low the volume level. The current volume level is shown with a red bar.

Press any button to return to the Main Menu.

VOLUME ADJUST

MAX.

1-23

Page 28

TROUBLESHOOTING

PROBLEM 1)

2)

3)

4)

5)

6)

7)

8) No picture or distorted picture.

Turn game On and nothing happens.

No sound.

No general illumination.

Press Start button and nothing happens.

No credit given for number of coins inserted.

Too many credits for number of coins inserted.

Game stays in test mode. POSSIBLE SOLUTION 1)

2)

3)

4)

5)

6)

7)

8)

1-24 Check for faulty video board or monitor. Check for disconnected video signal cable.

Check line fuse. Check for +5Vdc at pins C, D, 3 and 4 of the JAMMA connector.

Check the speaker and the speaker connection to pin L and 10 on the JAMMA connector. Check volume control setting. Check for +12Vdc at pins F and 6 on the JAMMA connector. Check for -5Vdc at pins E and 5 on the JAMMA connector.

Check the 1A, S.B. fuse in the AC power pack assembly.

Check for open wires between the button and the CPU board. Check for contamination on CPU board pins or the Start button switch blade contacts. Check for proper ground.

Check DIP switch coin settings. Check for contamination on the coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the JAMMA connector or Coin Switch 2 and pin T of the JAMMA connector.

Check the game pricing settings. Check for a short between pins T & 16 on the JAMMA connector.

Check that the switch #8 of DIP switch bank #2 is set to off.

Page 29

MORTAL KOMBAT MEOIRTALS COWRA

SECTION

TWO

PARTS

Page 30

CABINET HARDWARE

Cabinet Assembly A-19178-40039 Lock Retainer Plate 01-7264 Upper Door Lock Cam 01-8989 Leg Leveler Plate 01-9155 Lock Plate 01-11285 Pad Lock Bracket 01-11286 Key Lock Bracket 01-11287 Door Bracket 01-11291 Shaft Caster 02-4404 20" Vent Hole 03-7602 Door Cam Lock 20-10187 Caster Wheel 20-9627

Coin Door Assembly 09-50000-33 Coin Door Blank w/Lock 09-41000 Mars Chute 01-11379 Coin Meter w/Diode 5580-13476-00

Glass Retainer Bracket 01-9607.1 Marquee Retainer 03-8252-2 25" CRT Bezel 03-8497 Cash Box Tub 03-8863 Leg Adjuster, 3" 08-7377 Clear Marquee Glass 08-7456-4 Clear CRT Glass 08-7456-10 Screened Marquee 31-2316

ELECTRONICS

CPU/Sound Board Assembly A-18968-40039 Power Supply Assembly A-19756 Mounting Bracket 01-13420 Power Supply 20-10167

MONITOR

Monitor Support Bracket 01-10819 Monitor Controls PCB Mounting Bracket 01-11251 25° Monitor 5675-13399-02

MANUALS

DBV Installation Instructions 16-9637 Operations Manual 16-40039-101

Page 31

CONTROL PANEL

Housing & Control Panel Assembly A-20092 Control Panel Assembly A-20126 Control Panel Cable H-20136 Security Latch Bracket 01-11955 Clear Overlay 03-9352 Plate 04-10061 15 Link Safety Chain 20-9275-2 Red Push-button 20-9687-1 White Push-button 20-9687-2 Blue Push-button 20-9687-3 Yellow Push-button 20-9687-5 Control Panel Hinge 20-9841.1 8-way Joystick 20-9978-1 Screened Overlay 31-2314 Base/Housing Assembly A-20122 Toggle Latch 20-9347

FLUORESCENT LAMP ASSEMBLY

Fluorescent Housing & Bracket A-15890 Lamp Locks 03-8327 18" Fluorescent Bulb, 15W 24-8809

SPEAKER

Speaker Grille 01-11859 8 Full Range Speaker 5555-13961-00

TRANSFORMER ASSEMBLY

Power Pack Assembly A-20121 A-19227 Fuse, SB, 1A, 250V 5731-06569-00 OR 5731-06569-00 Fuse, SB, 3A, 250V 5731-10356-00 3731-10356-00 Line Voltage Cable H-20098

CABLES

Line Voltage Cable A-17877-3 Dixie-Narco Adaptor Cable H-17019 Main Harness Cable H-19068.1 Speaker Cable H-19599 Contro! Panel Cable H-20136 Line Cordset (North American) 5850-13271-00

Page 32

CPU/SOUND BOARD ASSEMBLY

Designation

Bi U57 U35 U45 U47 U2 U3 U4 US U133 U132 U131 U130 U129 U128 U127 U126 U125 U124 U123 U122 U121 U120 U119 U118 U54 U63 U117 U116 U115 U114 P3 P9 P10 P8, P11, P12 A-18968-40039

Part Number Description

5880-11056-00 Battery, 3V Lithium A-20093 Sound PLD Assy A-20095 FPGA Assy A-20096 FPGA Assy ‘A-20097 FPGA Assy A-5343-40039-02 EPROM Assy, Music/Speech A-5343-40039-03 A-5343-40039-04 A-5343-40039-05 4-5343-40039-06 A-5343-40039-07 A-5343-40039-08 A-5343-40039-09 A-5343-40039-10 A-5343-40039-11 A-5343-40039-12 A-5343-40039-13 A-5343-40039-14 A-5343-40039-15 A-5343-40039-16 A-5343-40039-17 A-5343-40039-18 A-5343-40039-19 A-5343-40039-20 A-5343-40039-21 A-5343-40039-22 A-5343-40039-23 A-5343-40039-24 A-5343-40039-25 A-5343-40039-26 A-5343-40039-27 5791-12461-05 5791-12461-07 5791-12461-10 5791-12461-15 EPROM Assy, Music/Speech EPROM Assy, Music/Speech EPROM Assy, Music/Speech EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Image EPROM Assy, image EPROM Assy, Image EPROM Assy, Image EPROM Assy, Program EPROM Assy, Program EPROM Assy, Program EPROM Assy, Program EPROM Assy, Program EPROM Assy, Program Header, 5-pin Header, 7-pin Header, 10-pin Header, 15-pin

Page 33

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 34

fone)

aaa —s ce) w+ stad Russesy Fa S © oy8 ges POWER SUPPLY 20-10167

Page 35
Scan of page 35

This page is a drawing, shown as the original scan.

Page 36

JAMMA Chart

| Ground Ground

Orange +12VDC Key Coin Counter 2__| Brown-Red NC Speaker- Brown-Gray N/C Coin Counter 1

Video Green Video Sync White Service Credits | White-Gray Black-Blue Black-Brown

Slam Tilt Black-Green

Black-Red Violet-White Violet-Black Violet-Brown Violet-Red Violet-Orange Violet-Yellow Violet-Green Violet-Blue White-Black White-Brown White-Red White-Orange White-Yellow 1 High Punch White-Green 1 Block White-Blue i White-Violet NC NIC

SOLDER SIDE COMPONENT SIDE Not Used slo lato lol» HHH

3-2

Page 37

INTERBOARD WIRING

GND =5V) » CPU/SOUND BOARD A~18968—40039 BY GND. zizfalele sia}<|afo || Gsese|

BL IN @tk-waT | P>

COIN 4BLK=YELé

KEY gy

+12V,‘ORG4Pg
BVRED3

CONS ——Bie=oRe—[} 3 SND “BLK 1

N KEY ar Neg Ne 7 | er é NLC 5 INTERLOCK _ BLK=GRY FA

VOLO=r}4
  • VOLUME ORG—RED[] 3 NIC 2

4 SWITCH 18 4 SWITCH 13 | = SWITCH ie 4 SWITCH i 4 RIGHT 10 EFT 3

4 DOWN.3Pit

+UP 7 4 START & | player « a

N/C 1S 3 SWITCH D BLU-VIO_ 14 3 SWITCH C BLU 13 S_SWICH B BLU-CRN 12 TIS SMITA BLUR VEL] 14 SRIGHT —BLU=ORG 1] +g

SULEFTBLU=RED [| 9p12

SBgHR—BLU=BRN 1 8 a BLUSBLK

TERT—suu=weir12 | PLAYER 3

NJ NIC 2 N/E. 3 N/E ne ie 2

3-3

Page 38

POWER WIRING AND TRANSFORMER DIAGRAM AC POWER CORD VOLTAGE JUMPER CHART vouTace | FUSE! PINS 100 sasa_|Saso 320 | si H

=(2302asa | sar

Bi POWER SWITCH [se no

ayeresa|

uN |

ETeR==|FEMALE | MALE|

TP 2||i2 of i 5|li3.9 | i rales 10 ogee RED. J

2sevN15 7 |||70
1S|/l8 3'
|edoof|88vies
po-E a|

id me 18 14)/ i ae He 15)! 158} —

2HE 18 5 50)a

| Gow Soo He [2 1) | [Steere vineo

|PSTransformerWOVEIS | | [2 Shea VE]MONITOR
701|/{7 ou“~
wotre
2\|)2ofecto! | fro}POWER
|AC POWERYas ¢ 318 =Pusvate2| | [2 otesurecy

" _

a vo83a
aN YELSRN YELIGHT

wove 15 § | | |3 olva ve. Fixture e183) | fk ope

UNE VOLTAGE+a

CABLE ASSEMBLY SS

NOTE: All Earth Ground Wires (green—yellow) connect to grounding stud on power pak ossembly.

POWER IN POWER OUT

ot} Fr ppe—_Ty GRN VEL e%| > gftki ve _| VIDEO

POWER SHITCHFEMALE MALEwo WEL TS 5 | \5 of Wo Yel | MONITOR)
coBLKBLK YEL7]{yoo—_—
raed Bl| 2 olgare1) [1 Ob Gara | POWER

“al i

i eR GRN YELSS3/3 Somvo vee tS 2 ovo we, —| SUP Puy |
!.izwi YEL39}Lo
— iaee [2bon
WHT RED3:—
=alTow.

z > of GRN YE | LIGHT

m-O55 ONO MELFIXTURE
amPeeor Se

250V 4ASB ‘S.SVAC, ero i q COIN DOR ae 22} [20 Lawes:

Page 39

aT = a 2 €|)) €or see nae Pore Srer| @ | 9 ("aks Sie dae pS £)| bop oe ore ‘ONS

= TIE ‘ONS

Fogg] € |) © Gage ome mo: fetta] & || age “Soon Folins ot ae net 38

mM r3MOd WVYSVIC ONIMIM LANISVD

Page 40

NOTES

3-6

Page 41

Control Panel Wire Color List

PLAYER ONE PLAYER TWO

FUNCTIONWIRE COLORFUNCTIONWIRE COLOR

Start White Start Violet-White Down White-Brown Down Violet-Brown

| UpWhite-BlackUpViolet-Black

Left White-Red Left Violet-Red

Right White-Orange Right Violet-Orange

| High PunchWhite-YellowHigh PunchViolet-Yellow

Block White-Green Block Violet-Green

High Kick White-Blue High Kick Violet-Blue

Low PunchBlue-BlackLow PunchBlue-Yellow
Low KickBlue-BrownLow KickBlue-Green
Run (Speed)Blue-RedRun (Speed)Blue
Page 42

WARNINGS & NOTICES

WARNING USE OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIPMENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS.
  • For safety and reliability, substitute parts and modifications are not recommended.
  • Substitute parts or modifications may void FCC type acceptance.
  • This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under federal law. This also applies to MIDWAY logos, designs, publications and \ assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
WARNING
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generated, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARNING Prevent shock hazard and assure proper game operation. Only plug this game into a properly grounded outlet. Do not use a cheater plug to defeat the power cord’s grounding pin. Do not cut off the ground pin.

NOTICE When MIDWAY ships a game, it is in compliance with FCC regulations. Your sticker is proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game does contain an FCC sticker, call MIDWAY immediately.

NOTICE No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.

Entire contents of this manual copyright © 1995 MIDWAY Manufacturing Company, INC. All Rights Reserved.

ae FOR SERVICE: CALL YOUR AUTHORIZED MIDWAY DISTRIBUTOR.

MIDWAY MANUFACTURING COMPS 3401 N. CALIFORNIA AVF CHICAGO, IL 606*