CATHODE RAY TOMES

Splat Instruction Manual (16-3011-101)

Splat! (Williams, 1982) · Instruction Manual · 29 pages · 32 sections · original scan

Page 1

16-3011-101

Instruction Manual

OPERATION BOOKKEEPING ADJUSTMENTS DIAGNOSTICS

PARTS

Page 2

ROM

SPLAT 4B

SPLAT 2B

SPLAT 3B

SPLAT 4B

SPLAT 5B

SPLAT 6B

SPLAT 7B

SPLAT 8B

SPLAT 9B

SPLAT 40B

SPLAT 11B

SPLAT 12B

Special Chip 4

Decoder ROM 4 (Horizontal)

Decoder ROM 6 (Vertical)

ROM 43 (Sound)

ROM SUMMARY

PART.NO.

A-5343-10071-B

A-5343-10072-B

A-5343-10073-B

A-5343-10074-B

A-5343-10075-B

A-5343-10076-B

A-5343-10077-B

A-5343-10078-B

A-5343-10079-B

A-5343-10080-B

A-5343-10081-B

A-5343-10082-B

A-5410-09941

A-5342-09694

A-5342-09821

A-5343-10127 DESCRIPTION

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

PROM, 4Kx8, BROWN LABEL

Special Chip

PROM, 512x8

PROM, 512x8

ROM, 4Kx8 IC12 CPU

SOUND

Page 3

INSTRUCTION MANUAL

FOR UPRIGHT AND TABLE GAMES

including... ¢ operation

¢ bookkeeping ¢ adjustment ¢ diagnostics

¢ parts

Page 4

CONTENTS

@CHAPTER 1 Game Setup

Warnings & Notices. ....... 2.66. c cece eee n eee e ne teen eect ne ee ee es 5

Examine Your GaMe...... 6... cece eee eee een ee cece ee eee 5 Location of Controls...........e cece cece eee eee eee e enter eee 6

CHAPTER 2 Game Operation

Power Turn-On. . 8

Game Operation. 8

Bookkeeping Totals. 8

Game Adjustments . 9

Definitions of Pricing Terms “1

CHAPTER 3 Troubleshooting Procedures

Introduction . 0.6.6... eee eee eee eee e tere teen eee nt eaten ens 14

POWEFUP TOStS. 0.6 c eet e nee e ieee een eter ae nen nent 15 +5VDC Power Supply Adjustments. ..............00ce cee ece een e ee 15 Self-Diagnostics..... 0... eee cece e cece cece eee e ence bette arene ees 15,

Diagnostic Mode Tests........... 6.05 cce cece cect e reer eee nee 16 Sound Board Diagnostics. ........... 6. ccc cette eee teense eee eee e ees 18 CMOS RAM Data Test Protocol ......... 6. cece eee c ee eee e eee eens 20

@CHAPTER 4 Parts

Page 5

CHAPTER 1 Game Setup

Warnings & Notices

Examine Your Game

Location of Controls

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7

Warnings & Notices

WARNING: @ 4. FOR SAFETY AND RELIABILITY, WILLIAMS does not tecommend or authorize any substitute parts or modifications of WILLIAMS equipment.
  • USE OF NON-WILLIAMS PARTS and modifications of game circuitry may adversely affect game play, or may cause Injuries.
  • SUBSTITUTE PARTS, MODIFICATIONS AND GAME “CONVERSIONS” may void FCC type-acceptance.
  • SINCE THIS GAME IS PROTECTED by Federal copyright, trademark and patent laws, so-called game “conversions” may be illegal under Federal law.
  • THIS “CONVERSION” PRINCIPLE ALSO APPLIES to unauthorized facsimiles of WILLIAMS equipment, logos, designs, publications, assemblies and games (or game features not deemed to be in the public domain), whether manufactured with WILLIAMS components or not.

RF INTERFERENCE NOTICE:

CABLE HARNESS PLACEMENTS AND GROUND STRAP ROUTING on this game have been designed to keep RF radiation and conduction within levels accepted by FCC regulations.

TO MAINTAIN THESE LEVELS, reposition harnesses and reconnect ground straps to their original placements If they should be disconnected during maintenance.

Examine Your Game

When you receive a new WILLIAMS game, examine It carefully before you power It up. Be sure It was delivered in good condition!

CIINSPECT THE OUTSIDE of the shipping carton and/or game cabinet for shipping damage.

CIUPRIGHTS: UNLOCK AND SET ASIDE THE TOP-REAR PANEL. Undo the two trunk latches on the inside of the bottom door. Open the door. Now check circuitry.

COTABLE GAMES: Unlock the coln door and pull on two latch bars to release and ralse the table top. Unlatch the component door and carefully lower It to the floor.

CARE CONNECTORS SECURELY ATTACHED? Reconnect any found loose, DON’T FORCE CONNECTORS. They're keyed and only fit one way. By the same token, take care: reversed edge-connectors can damage PC boards!

DARE PLUG-IN CHIPS FIRMLY-SEATED in thelr sockets?

COUNWRAP THE POWER CORD coiled inside the cabinet. Now position the cord in the wood slot beneath the bottom door. (Table games: Drop the plug through the hole in the floor. DON'T PLUG IT IN YET!

COSCRUTINIZE MAJOR SUBASSEMBLIES, such as the monitor, control panel, transformer board and power supply. Make sure they’re securely-mounted.

Page 8

Location Of Controls

THE ON-OFF SWITCH Is situated on the top-left corner of upright games as you face the back of the cabinet. Table games have an on-off switch underneath the game.

THE VOLUME CONTROL in upright games is located Inside the coin door and on the right cabinet wall as you face the game.

DIAGNOSTIC SWITCHES are on the back of the coin door in upright games. In table games they're under the table-top.

These switches are used to access the Diagnostic- Mode Tests, the BOOKKEEPING TOTALS screen and the GAME ADJUSTMENTS screen. Refer to the appropriate sections below for information on each of these important features. OTHER CONTROLS. Finally there are three more controls that are used somewhat less often that those above:

  • The memory-protect Interlock switch is near the diagnostic switch bracket (see above). This switch must be open when you clear BOOKKEEPING TOTALS or make GAME ADJUSTMENTS. It automatically opens when the coin door is open on upright or mini games and when the table-top is raised on table games.
  • The CPU board reset switch is located across the CPU board from the batteries.
  • The cashbox advance swlich, found inside the cashbox door on upright games, allows bookkeeping information to be audited without permitting it to be zeroed.
Page 9

CHAPTER 2 Game Operation

Power Turn-On Game Operation

Bookkeeping Totals

Game Adjustments

Definitions of Pricing Terms

Page 10

Power Turn-on

CAUTION: This game must be plugged into a properly-grounded outlet to prevent shock hazard and to ensure proper game operation. DO NOT use a “cheater” plug to defeat the ground pin on the line cord, and DO NOT cut off the ground pin.

WHEN THE GAME IS FIRST TURNED ON it produces a sound. Simultaneously general illumination should come on and a moment later a scanning “rug pattern” indicating the RAM test should appear on the screen. Next the rug should become stationary as the ROM test is performed.

IN A CORRECTLY-RUNNING GAME the rug pattern will be followed by the message “INITIAL CHECKS INDI- CATE ALL SYSTEMS GO”. If RAM or ROM failure messages come up on the screen instead, refer to Power Up Tests in TROUBLESHOOTING PROCEDURES.

Game Operation

GAME START

INSERT COINS. With two or more credits displayed, pressing 2-player start initiates a simultaneous 2-player, 3-turn* game.

SELECT YOUR CHARACTER with the walk joystick.

THE WALK JOYSTICK moves your character around the screen In any of eight directions: N-NE-E-SE-S-SW-W- NW.

THE THROW JOYSTICK is your means of attack. It controls your throwing arm and permits you to launch a volley in the same eight directions.

NO ONE HAS EVER FOUGHT LIKE THIS BEFORE! A long conveyor belt has been loaded with the most devilish of culinary concoctions...both for you and for your opponents. Imagine an endless supply of apples, bananas, ples, cakes and much more. It's a veritable chef's nightmare! But don’t examine them; catch them as they fall from the conveyor beli!

THEN SEEK OUT YOUR OPPONENTS. Aim your perishable missles and throw...SPLAT! A direct hit will positively cause them to lose their heads. But while they regain thelr composure, don't tarry. Reload for the next fusillade!

OTHERWISE THE HIT MAN will appear as if from nowhere...and pelt you with all manner of groceries.

AND BEWARE THE CORN STALKER! You may have to pick up a key and run out one of the doors to the other side of the kitchen. Then beat him at his own game and give him what-forl Re-enter the kitchen, grab a handful of goodies, and toss a salad...on him!

“adjustable feature THE GARBAGE CREATURE emerges after awhile, as he must in all kitchens. He's quite a mischievous animal, so you'll have to use your cunning against nim. os @ well as your dessert. For victory you must let him have it twice, and he travels fast. Don't get in his way!

NERDS TO CONTEND WITH. This is your reward for bettering the garbage creature. How true-to-life! They may be nerds, but there are too many of them to take lightly. Time for target-practice again!

THE KITCHEN SCENES change every *30 seconds.

IF YOU'RE HIT ONCE WITH FOOD you lose your head. You must retrieve it to throw food. If you're hit twice you lose 4 life.

EACH NEW LIFE: A door flashes for you to re-enter. Use THROW to enter; use WALK to select another door.

EXTRA LIFE every *20,000 points

HIGH SCORE SIGNATURE

Select letters with the move joystick. Lock in letters with the throw joystick.

Bookkeeping Totals

  • (a) Upright Games In Game-Over Mode, open the cashbox and depress the cashbox advance switch. The advance switch located on the diagnostic switch bracket can also be used. (See Figure 1.) The CRT should indicate all bookkeeping and evaluation totals. If so, go to step 3. If the CRT display comes up in the ROM test, perform step 2.
  • Table Games With center switch set to AUTO-UP depress the ADVANCE switch on the diagnostic switch bracket (See Figure 1). Proceed from step 3.

Figure 1. Diagnostic button switches

  • Continue to depress the cashbox advance switch, stepping the game through test programs for ROMs, RAMs, CMOS RAM, sounds switches, color RAMs, and then CRT test patterns, of which there are five. The fifth test pattern, color bars, directly precedes the CRY display of the bookkeeping ~@ evaluation totals.
  • The bookkeeping and evaluation totals appear on the CRT as in Figure 2.
Page 11

BOOKKEEPING TOTALS

LEFT SLOT COINS CENTER SLOT COINS RIGHT SLOT COINS PAID CREDITS NUMBER OF WAVES COMPLETED TOTAL TIME IN MINUTES TOTAL LIVES PLAYED TOTAL SINGLE PLAYER TOTAL QUAL PLAYER TOTAL CREDITS PLAYED AVERAGE TIME PER CREDIT

Figure 2, Bookkeeping display

CLEARING BOOKKEEPING TOTALS

  • Depress ADVANCE to display Game Adjustments.
  • Use the joystick to position the cursor beside CLEAR BOOKKEEPING TOTALS (Figure 3).
  • Push the 2-PLAYER button.
  • Depress ADVANCE.

Game Adjustments

With the AUTO-UP/MANUAL-DOWN switch set to AUTO- UP, depress the coin door ADVANCE switch twice to cause a CRT display as shown in Figure 3.

Select the adjustment with player 1 MOVE and change the value with piayer 1 THROW.

Now for the multiple choice section! Choose one or more:

CO Select an appropriate difficulty level: 0 = easiest or liberal, 5= average, 9 = hardest or conservative. For a shorter game, increase the bonus points figure (EXTRA LIFE EVERY). For a longer game, reduce it. (4,000 = long / 79,000 = short).

CMake It easier or harder for the player to progress thru the waves with number of seconds in a wave. (45 = easier/99 = harder).

For a shorter game, decrease the initial NUMBER OF LIVES. For a longer game, increase the number. (4=short/79 = long).

GAME PRICING is selected with standard settings or with custom settings as shown in Table 4. Note that free play can be elected by entering the code number 9 at the PRICING SELECTION function.

FOR STANDARD SETTINGS you need change only the PRICING SELECTION. For custom settings, first set PRIC- ING SELECTION to zero and then set the remaining values according to Table 1.

Page 12

GAME ADJUSTMENTS

NUMBER OF SECONDS IN A WAVE

INITIAL NUMBER OF LIVES

EXTRA LIFE EVERY

PRICING SELECTION

LEFT SLOT UNITS

CENTER SLOT UNITS

RIGHT SLOT UNITS

UNITS REQUIRED FOR CREDIT

UNITS REQUIRED FOR BONUS CREDIT

MINIMUM UNITS FOR ANY CREDIT

DIFFICULTY OF PLAY

LETTERS FOR HIGHEST SCORE

RESTORE FACTORY SETTINGS

CLEAR BOOKKEEPING TOTALS

HIGH SCORE TABLE RESET

AUTO CYCLE

SET ATTRACT MODE MESSAGE

HIGH SCORE TO DATE ALLOWED YES

USE ‘PLAYER t WALK’ TO SELECT ADJUSTMENT

USE ‘PLAYER t THROW’ TO CHANGE THE VALUE

PRESS ADVANCE TO EXIT

Figure 3. Game adjustments showing factory settings

HIGHEST SCORE SIGNATURE SETTING ATTRACT MODE MESSAGE

The number of letters allowed the highest-scoring 1. Position the cursor beside SET ATTRACT MODE Player for entering his name can be varied from 3 to MESSAGE. 20 and is recommended as 3. If objectionable words 2. Lift up on player 1 THROW. are entered as the signature name, you can change 3. Depress ADVANCE. the lettered entry leaving the highest score the same. 4. Enter up to two lines of your message following See Setting Highest Score Name. instructions on the screen.

  • Depress ADVANCE to enter Game-Over Mode.

RESTORE FACTORY SETTINGS To restore the Williams attract mode message, perform steps 1 through 3 and then turn the game OFF and back ON.

  • Position the cursor beside RESTORE FACTORY SETTTINGS.
  • Lift up on player 1 THROW. SETTING HIGHEST SCORE NAME
  • Depress ADVANCE twice.
  • Position the cursor beside SET HIGHEST SCORE NAME. Lift up on player 1 THROW. Depress ADVANCE. Enter the new signature. Depress ADVANCE to enter Game-Over Mode. RESETTING HIGH SCORE TABLE
  • Position the cursor beside RESET HIGH SCORE TABLE.
  • Lift up on player 4 THROW.
  • Depress ADVANCE. VRon

An alternate, simpler method enters the factory highest score signature. In the Game-Over Mode, hold HIGH SCORE RESET down. After a few seconds a sound is produced and the factory highest score signature has been activated.

Page 13

Table 1. Game Pricing

Units Min,

Req'd | Units

Lett| Confer | Right | UnitsForFor
Coin DoorCredits/Pricing | SlotSlotPerBonus | Any
MechanismMoneySelection | Units | Units | Units | Credit | Credit | Credit
Twin Quarter11256, 5/S40441140
Quarter, Dollar,2/506, 5/540141442
Quarter01/286, 4843 |4441|00
2/506, 4/640141102
41506, 3/64, 4/542503123450
1506, 3/84, 7/82024812149624
04/506, 3/$4, 6/$244a |4240
04/50654442o |o
‘1DM, 5DM4/1DM, 6/5DM2604400
20-Cent, 50-Cent11206, 95060é05500
4 Franc, Frane4/2F, 3/5F only416620@
25 Cent,01/256, 4466404400
1 Guilder11256, SAG0104140
5 Franeo4/5F, 2/40F7[402400
40 Franc.@4/40F840220(J
‘1 Frane, 2 Franc2/4F, 5/2F26041o |0
100 Lire, 200 Lire$4/200 Lire84022.|00
Twin Coin04/1 Coin34441|0o|
04/2 Coins5141200
413 Coins 2/5 Coins0202500
04/2, 3/54166200
4-Unit, §-Unit1, 5150105100
=113, 21502010500
‘AnyFree Play911400

Definitions Of Pricing Terms

PRICING SELECTION allows a shorthand method of setting the pricing functions. If a number from one to nine is entered into the PRICING SELECTION function, a corresponding standard setting (shown in bold type above) will be entered into the game. The rest of the pricing functions are automatically set for that standard.

THE PRICE OF ONE GAME (number of coins per game) is equal to the number of SLOT UNITS for any one slot divided by the number of UNITS PER CREDIT. If the number of LEFT SLOT UNITS (or RIGHT SLOT UNITS) equals X and the number of UNITS PER CREDIT equals Y, then the price of one game Is X/V.

UNITS REQUIRED FOR BONUS CREDIT is the number of games that must be purchased before a free game is awarded.

MINIMUM UNITS FOR ANY CREDIT is the least number of coins allowed per game or games: Or. put another way, the MINIMUM UNITS FOR ANY CREDIT determines the smallest number of whole games that may be paid for at one time. For example if an operator wants fo allow one play for a quarter but wishes to encourage multiple gameplaying, he may enter.

"0" in the PRICING SELECTION function

This zero value automatically sets all pricing functions. However minimum units for any credif must be raised to “2° or higher value to achieve the operator's goal. Here are fhe rest of the functions as they should appear.

"1" in the LEFT SLOT UNITS function “4” in the CENTER SLOT UNITS function “4” in the RIGHT SLOT UNTIS function e*0" in the UNITS REQUIRED FOR BONUS CREDIT function "4" in the UNITS PER CREDIT Function e*2” in the MINIMUM UNITS FOR ANY CREDIT function

These values allow one game to be played for a quarter, but ONLY when two or more games are paid for at a time. Incidentally, the “4” in CENTER SLOT UNITS allows four games per dollar coin (center slot only). See “2/50¢, 4/$1” above. "

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

CHAPTER 3 Troubleshooting Procedures

Introduction

Power-Up Tests

+5VDC Power Supply Adjustments

Self-Diagnostics Diagnostic Mode Tests Sound Board Diagnostics

CMOS RAM Data Test Protocol

Page 16

INTRODUCTION

Certain types of game malfunctions may inhibit the game's shooting algorithm begins with Power-Up and continues until diagnostic or display faculties. Troubleshooting procedures Game Over Mode. All procedures can be performed with tor most of these types of malfunctions as well as malfunctions minimal test equipment or merely by observing the game that permit self-diagnosis are covered below. Our trouble- itself.

POWER-UP TESTS

NO GENERAL NO INITIAL VIDEO CHECKING POWER ILLUMINATION (RUG PATTERN) ‘SUPPLY BOARD

  • Check fuse F2 on power supply board. (1) Press reset button on CPU Board.
  • Check tor proper installation of jum- (2) Try RAM and ROM Diagnostic-Mode pers W1, W2, W3 and/or resistor R27. (Some tests (see below} machines MAY NOT have an R27. Refer to (3) It these tests don't turn up the problem, your drawing set) check power supply board.
  • Check 4P4/J4, 4P3/J3, 6P2/J2 and 6P3/J3.
  • If all the above don't turn up the prob- Jem, check power supply board.
  • Swap power supply board with one from known-good game.
  • It game plays, problem is on power supply board,
  • If game doesn't play, check power transformer with voltmeter.
  • If known-good power supply is unavailable for tests above, check +5V, -5V and +42V outputs on power supply In game. Each MUST BE within 2% of rated output with less than 0.4% AC hum.

ROM BOARD LEDS RECOGNIZE CONDITION ROM BOARD LEDS IDENTIFY BAD CHIPS

“0° means all power-up tests passed

  • scanning rug pattern {2) stationary rug pattern
  • “INITIAL TESTS INDICATE ALL SYSTEMS to Diagnostic-Mode tosis.

co"

  • Game-Over Mode If any video (see left) is missing or error message is displayed, proceed

CMOS (See Appendix A) “HIGH SCORE TABLE RESET” “BOOKKEEPING TOTALS CLEARED” “ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS BY OPENING FRONT DOOR OR TABLETOP AND TURNING GAME ON AND OFF*

“FACTORY SETTINGS RESTORED” "0" means tests (4) Open coin door or tabletop and turn power off and on.

  • Press ADVANCE. Game should teturn to Game-Over Mode. “0" means tests passed

BATTERY (See Appendix A) “0” means tests passed “HIGH SCORE TABLE RESET” "BOOKKEEPING TOTALS CLEARED” “ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS BY OPENING FRONT DOOR OR TABLETOP AND TURNING GAME ON AND OFF"

  • Open coin door or tabletop and turn power off and on. Or: press ADVANCE. In either case, game should return to Game-Over Mode.
  • Check AA alkaline cells on CPU Board.
  • If problem persists. proceed with CMOS RAM test by putting the game into its Diagnostic-Mode (see SELF-DIAGNOSTICS).

MEMORY “0” means tests

PROTECT Passed “BOOKKEEPING TOTALS CLEARED”

INTERLOCK “ADJUSTMENT FAILURE” (See “RESTORE FACTORY SETTINGS Appendix A) BY OPENING FRONT DOOR OR TABLETOP AND TURNING GAME ON AND OFF” “HIGH SCORE TABLE RESET” (1) Making and breaking memory Protect interlock switch, check with VOM and replace if faulty.

  • Replace If faulty: Memory protect gates 6E, IC1, Q1, or CMOS RAMS.

0" means tests passed SPECIAL CHIP (1) scanning tug pattern

  • blank screen instead of “INITIAL TESTS INDICATE ALL SYSTEMS GO*
  • high score table with no scores
  • intro blank or program crash
  • Turn power off.
  • To tind bad chip, replace 2 special chips one at a time with known good chips.
  • Turn machine on atter each replacement and run through Power-Up Tests.
Page 17

+5VDC Power Supply Adjustments

Before adjusting the voltage output, always check at the output of the supply for AC hum. This hum should never rise above .00SV on the +5VDC supply. If it does, consult your schematic drawing set for proper DC voltages throughout the circuit.

Test for these with the DC setting of your multimeter. Make a second check using the AC setting. Pay particular attention to readings at TP5 (top of capacitor C10). If the voltage here is low (less than +44VDC) or if you find excessive ripple (more than 700mVrms), replace the capacitor.

If TP4 is less than +4.95VDC remove R10. If TP4 is still less than +4.95VDC, then check ptecision resistors R25 and R26. If they are within the 1% tolerance, then check IC2.

Self-Diagnostics

If RAM or ROM failure messages are displayed on the CRT after the “rug pattern,” proceed with selfdiagnostics. Selt-diagnostic procedures are controlled by the AUTO-UP/MANUAL-DOWN and ADVANCE switches. (See Figure 4.)

Set the AUTO-UP/MANUAL-DOWN switch to the MANUAL-DOWN position and depress the ADVANCE Pushbutton. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results Present on the CRT display, set the AUTO-UP/MANUAL- DOWN switch to the AUTO-UP position. Depressing the ADVANCE pushbutton initiates the RAM test. Further tests (CMOS, sound, switch, color RAM and monitor test patterns) are encountered one after the other as the ADVANCE pushbutton is depressed (once more for each subsequent test).

MONITOR TEST PATTERNS (19"-Monitor Upright Games only.) For ease in monitor adjustments, the monitor may be slid back and the screen viewed in the CRT mirror on the inside-top of the cabinet.

Remove the two bolts and carefully slide the monitor back in its shelf. Secure the monitor in the extended Position by inserting the two bolts through holes provided at the left side of the monitor.

AUTO-CYCLE MODE. From the color bar pattern (or Game Over with the switch set to AUTO-UP) depress ADVANCE two times to display GAME ADJUSTMENTS.

  • Position the cursor beside AUTO CYCLE with the joystick and lift up on player 4 THROW.
  • Depress ADVANCE.
  • The system will now sequence through ROM, RAM, and CMOS RAM tests repeatedly. The coin door must be open during the Auto-Cycle test. If an error is detected, the test is terminated and the failure indication is displayed on the CRT.
  • To terminate the Auto-Cycle test, turn the game OFF and ON.

LEGEND: FIRST DESIGNATION (3K) IS CIRCUIT BOARD GRID REFERENCE. DESIGNATION IN PARENTHESIS DENOTES BANK NO. (1-3) AND CHIP NO. (1-8).

1s, BANK? INTERFACE INTERBOARD CONNECTOR A

o BIETETEIEIETETENE [een J

Figure 4. RAM Location and Numbering on CPU Board

Page 18

ROM BOARD LEDS RECOGNIZE CONDITION |AGNOSTIC-MODE TESTS

ROM BOARD LEDS IDENTIFY BAD CHIPS

means ROM error it ROM chip “ROM ERROR” and ROM no. chip no.

RAM 4" means RAM error

CMOS (see appendix A) “3" means CMOS RAM error Bank no. first...then chip no. in bank (see figure 4) “RAM ERROR’ followed by RAM bank no. and chip no. (Note: with multiple RAM failures this display may net appear)

“CMOS RAM ERROR OR WRITE PROTECT FAILURE”

  • Turn power off.
  • Replace suspected chip.
  • Check for these normal voltages on indicated RAM chip: -5/pin 4, +42/pin 8, +5/pin 9.
  • Turn power off.
  • Replace suspected chip. {4) With multiple RAM failures always check power supply. See POWER-UP TESTS.

{4} With power off, check pin 18 of CMOS RAM for 3.2VDC minimum. If present, check or replace CMOS chips. If absent, replace AA alkaline cells.

  • With new alkaline cells and power off, check for 3.2V minimum at pin 48. if still absent replace diodes D9 and D410.
  • Upon power-up and reentry into diagnostics if CMOS error message persists, check CMOS RAM memory protect and address decoding circuits with a logic probe.

Tests 4 and 7 provide sequential subtests. To stop automatic cycling set switch to MANUAL-DOWN. Depress ADVANCE in MANUAL-DOWN to step through subtests. LED indications are not made for these iests.

SOUND (Test 4)

SWITCH (Test 5)

{1} Set switch to MANUAL-DOWN and clear any stuck switches.

  • CRT should indicate no switches closed,
  • Operate switches and check for display of switch name. “SOUND LINE. 1” “SOUND LINE 2" “SOUND LINE 3° “SOUND LINE 4” “SOUND LINE 5° "SOUND LINE 6” (These appear one at a time.)

CRT indicates AUTO-UP closed and any stuck switches. GRT Display for each Switch...

ROM BOARD INTERFACE BOARD

ADVANCE ‘AUTO-UP HIGH SCORE A-PLAYER START 2-PLAYER START WALK UP 4 WALK DOWN 4 WALK LEFT 4 WALK RIGHT 4 WALK UP 2 WALK DOWN 2 WALK LEFT 2 WALK RIGHT 2 THROW UP 4 THROW DOWN 4 THROW LEFT 4 THROW RIGHT 4 THROW UP 2 THROW DOWN 2 THROW LEFT 2 THROW RIGHT 2 LEFT COIN CENTER COIN RIGHT COIN SLAM SWITCH MISSING — CHECK 2P4/40P3 pin 3 2P4/40P3 pin 2 2P4/40P3 pin 5 2P4/40P3 pin 4 2P4/40P3 pin 7 ‘2P4/40P3 pin 6 perform Sound Board Diagnostics (see below)

NOTE: If any two sounds are the same, check for ¢ short between the select lines with the same sound.

{Refer to CABINET WIRING Diagram)

  • ROM BOARD SWITCH STUCK: Disconnect 2P3.
  • INTERFACE BOARD SWITCH STUCK: Disconnect 3P2 or 3P3.
  • ROM BOARD SWITCH DOES NOT OPERATE: Ground corresponding pin of 2P3.
  • INTERFACE BOARD SWITCH DOES NOT OPERATE: Ground corresponding pin of 3P2 or 3P3. COSYMPTOM REMAINS SAME ... ROM Board or Interface Board Faulty. CUSYMPTOM CLEARS UP ... Problem is in switches ‘or wiring. ADDITIONAL TESTS FOR OPTO SWITCHES
  • Check that +5VDC is at pin 1 of 42P4,
  • With joystick in center position, check for 0.1V Gt base of OFF transistor(s) (1 thru @4} and +SV at pin(s) 4, 2, 4 and 5 of 12PA.
  • With joystick moved from center position, check for 0.7V at base of transistor(s), and O.4V at corresponding pins 4, 2, 4 and 5 of 12P1.
Page 19

COLOR RAM (Test 6)

Note that a blank sequence or two sequences with the same shade indicate a faulty 1A flip-flop, 18 RAM or 2B RAM or a failure in the color analog circuit. Check voltages on Q1 (green transistor), Q2 (red transistor) and Q3 (blue transistor). During the eight full-screen color tests, the base voltage (center pin) on each transistor should vary between 3.8V (brightest color) and 4.4V (no color).

Color RAM Check

  • CRT sequences through 8 colors, 2 seconds each.
  • Thick horizontal band indicates color RAM fault.

MONITOR & COLOR RAM (est 7)

MORE DIAGNOSTIC MODE TESTS

VIDEO SEQUENCES REMEDY OR ADJUSTMENT

  • light red screen
  • red screen
  • dark red screen REPLACE RAM 4B REPLACE RAM 2B

too-light or too-dark red or gray band

  • light green screen
  • green screen
  • dark green screen yellow band cyan band
  • light blue screen
  • blue screen magenta band too-light or too -dark blue or gray band
  • light green screen green band dark green band or gray band
  • green screen light green dark green band band or gray band
  • dark green screen

cross hatch pattern gray band

Aids you in setting up vertical and horizontal linearity, convergence, and focus.

red screen green screen blue screen color pattern Aids you in optimizing color purity.

color bars + double-width half-width +transposed *missing If color RAM test 6 indicates no faults, symptoms at left suggest a fault in 44, 4B, 2B or 2C chips.

Page 20

SOUND BOARD DIAGNOSTICS

MISSING SOUNDS; 1 CHECK SOUND-SELECT INPUTS

NO SOUND—STEP 4| TestTOOLCONDITION & REMEDY
(ASSUMPTION:Sound Boardlogic probe (game«PULSING-proceed
INPUT SECTIONconnector 10P3/J3-2‘on and in Test 4)+*LOW-check jacks, foils
FAILURE}“7*STILL LOW-perform ROM BOARD

checkbox. |

SR1 DIP resistorsVOM-reading ohmsALL 4.7K-proceed
R3-RO(game off]*ANY OPEN-replace SR1
C3-C9VOM-reading ohmsALL OKAY-proceed

(game off) ANY SHORTED-replace bad

IC5+4, 1C7-44logic probe (game-HIGH-proceed
(power pins)on and in Test 4)*LOW-replace C49 (IC5) or C24 (IC7)

+STILL LOW-replace bad IC

1C5-2, 4, 6, 10, 12, 15;logic probe (game«PULSING-proceed
1C7-4, 6‘on and in Test 4)+LOW-replace chip
1€40-18 and 19logic probe (game«PULSING—-proceed
(PIA)‘on and in Test 4)+LOW-litt C20, retest

*PULSING NOW-replace C20 STILL LOW-teplace IC6, retest

110-10 to 17logic probe (game-PULSING-proceed
(PIA)‘on and In Test 4)*SOME LOW-replace IC

+ALL LOW-lift C31, retest +PULSING NOW-repiace C34 STILL LOW-replace IC

Page 21

MORE SOUND BOARD DIAGNOSTICS

MISSING SOUNDS; C1 CHECK ROM BOARD OUTPUTS NO SOUND—STEP 2 (1) If you hear game sounds, disconnect and then reconnect Sound Board connector 40P3/J3.

  • You should hear one or more game sounds. If so, put game in Diagnostic Mode Test 4 and proceed with this checkbox. If not, go ahead to POWER SUPPLY checkbox below.

TEST TOOL CONDITION & REMEDY

(ASSUMPTION: OFF-BOARD FAILURE}

ROM Boardlogic probe (game.PULSING-repair cable to Sound
connector 2P4/J4-2on and in Test 4)Board

to7 *ANY LOW-repair jack oF foil, proceed

9C DIP resistors 2 to 8VOM-teading ohms+ALL 4.7K-proceed

(game off) ANY OPEN-teplace 9C

40-53VOM-reading ohms.ALL OKAY-proceed

{game off) *ANY SHORTED-replace bad

logic probe (game «PULSING-proceed on and in Test 4) *SOME LOW-replace 8C

C1 CHECK ON-BOARD POWER SUPPLY

  • With power off, test for fuse continuity at F4 and F2.
  • With power on, check for +42V unregulated DC at TP4 and at pin 5 of IC4.
  • Now check for +5V regulated DC between TP4 and TP3. If voltages are absent or low, turn off game and lift one pin of filter capacitors C25, C26 and C27.
  • Check each with ohmmeter for possible shorts.
  • If capacitors are good and unregulated voltages test okay but you're missing +5V, replace regulator chip (IC8). C CHECK AUDIO (ANALOG) SECTION
  • Turn power on; turn up volume control. Momentarily place powered-up AC soldering pencil on final amplifier's input pin (IC4, pin 1 or 10P4, pin 2). If you hear low hum, audio IC, volume pot and speaker are okay.
  • Repeat test at Q2 emitter. If you hear hum, analog section is okay. Step (1) will also work if you simply touch amplifier’s input pin. However oufput level of hum will be much lower than with soldering iron. DO NOT use a soldering pencil of over 40 watts. Cordless models will NOT work here.

C CHECK SOUND ROM (1C42) AND RELATED CIRCUITRY

  • Turn power on.
  • If you have no game sounds but power supply fests show normal voltages and no ripple on +5¥, check crystal clock circuit. Using DVM or logic probe, test for pulsing AC across crystal. if clock signal's absent, replace crystal and associated capacitors.
  • Turn power off.
  • Swap sound ROM (IC12) and then microprocessor chip (IC9) with known-good chips.
  • Powerup and test Sound Board after each swap by pushing DIAGNOSTIC button. 8C-10 to 15 (PIA)

NO SOUND

(ASSUMPTION: POWER SECTION FAILURE)

STILL NO SOUND

(ASSUMPTION: AUDIO SECTION FAILURE)

MISSING SOUNDS; NO SOUND

(ASSUMPTION: DIGITAL FAILURE)

19:

Page 22

CMOS RAM Data Test Protocol

The first sub-test of the CMOS RAM data is that of the ATTRACT MODE MESSAGE checksum. If the test does not pass, the factory ATTRACT MODE MESSAGE is restored. Next, the game adijustments are checked and restored to factory settings if an error is found. If game adjustments are found intact, the high score table is checked for any bad entries. Bad entries are replaced with a score of 4,000 points and no initials. If all entries check, the game returns to the Game Over Mode.

If game adjustments are restored to factory settings, the AUDIT TOTALS are checked. If 5 or more audit digits are other than 0-9 (that is hexadecimal A through F) all audit totals are cleared. This is followed by a check of the high score table and the table is reset to factory settings if errors are found. Finally, game adjustments are rechecked and either OPEN COIN DOOR or FACTORY SETTINGS RESTORED is displayed. With the former, open the coin door and turn the game OFF and ON and then FACTORY SETTINGS RESTORED will be displayed. Return to game over by depressing the ADVANCE pushbutton or by turning the game OFF and ON a second time. ATTRACT MODE MESSAGE?

RESTORE FACTORY MESSAGE

RESTORE FACTORY SETTINGS,

AUDITS

HiGh score TABLE

RESET HIGH SCORE TABLE TO FACTORY SETTINGS HIGH SCORE ENTRIES

‘BAD ENTRIES REPUCEO WITH 4,000 AND NC INITIALS,

INITIAL TESTS INDICATE ALL ‘SYSTEMS GO DISPLAYED.

“OPEN COIN DOOR’ DISPLAYED

OPEN COIN DOOR POWER OFF AND ON

0) se RESTORED’ DISPLAYED,

POWER OFF AND ON

Page 23

CHAPTER 4 Parts

Page 24

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 25

2c -9267

01-7310

4608-01080-07

4320-01123-20-

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

§792-09094-00

§791-O9111-00

5014-09170-00

5792-09565-00

4008-01017-08

\ 20-9230-2 5792-09336-00

$792-09288-00

| ~~8792-09103-00 (conn) 5822-09076 (PIN) appa: 822-090 0-8224-3011 s79e-09617-00 $808 08078 (FIN)

5792-09567-00

5731-06569-00

5731-09651-00 5731-06314-00 |-P/0 0-8784

8731-09432-00

5731-09432-00

one yy . SL Y ~ ee PAD H-8810 | BUA yd $792-09698-00(CONN) CE yy 5823-09360-00 (KEY) gS ov. ~. 5901-09652-00 5162-09425-00

4006-01003-10

P/0 C-8809 5161-09552-00"

Page 28

§792-09502-00

Page 29

78cm)

65" li65em)

UPRIGHT

Weight 270 lbs. (122.5 kg.) uncrated 290 ibs. (131.5 kg.) crated

28.5" (7a.Sem)

COCKTAIL TABLE Weight 205 Ibs. (98 kg.) uncrated 220 Ibs. (100 kg.) crated

23.8" 28.5" (60,5em) (125em)

27.5" (70cm)

Warning—This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been certified to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to correct the interference. POWER REQUIREMENTS 115/230 VAC Nominal, 50/60Hz @1.7/0.85A 192W (20A surge tor one cycle at power turn on) Normal Line = 98-126VAC 196-252VAC High Line* = 113-145VAC 226-290VAC Low Line* = 88-113VAC 176-226VAC “Transformer jumpers required. See service manual. ENVIRONMENT Sree Temperature 0° to +45°C ambient (+32? to +118°F)

Storage Temperature

—40° to +65°C ambient (—40° to +149°F) 90% RH at 40°C (104°F), non-condensing MONITOR 19" Color Raster" non-interlaced UL, CSA & DHHS Approved VIDEO SYSTEM” 256 Colors, 340 x 240 PIXEL Resolution 6809E Microprocessor ROM: 48K BYTES Video and Scratch RAM: 50K BYTES CMOS RAM: 1Kx4 SOUND SYSTEM** 6808 Microprocessor ROM: 4K BYTES JOYSTICK Two 8-way optical-digital Two 8-way leaf switch

**Patent pending Specifications subject to change without notice.

SERVICE For the back-up that keeps you out-front, call Williams toll-free at 800/621-125, In Illinois, call toll-free at 800/572-1324.

ELECTRONICS, INC. 3401 N. California Ave., Chicago, IL 60618 (312) 267-2240, Telex 253095

NOTICE: “SPLAT” is a trademark of Williams Electronics, Inc. ar bctath/ ahs 6 alae ek tc edeoinmas tee