Life Force
Salamander (version D) (Konami, 1986) · Document · 12 pages · 19 sections · original scan
KONAMI.
U.S.AY
USA
usa
od KONAMI @ is a trademark of Konami Industry Co., Ltd.
TABLE OF CONTENTS
Page Page
Conversion Kit Contents........ Inside Cover WiringDiagram....................000 6
Introduction .............. cece eee eee ee 1 Stereo/Mono Sound Installation........... 7
Graphics..... 0.0... ccc eee eee 2 Technical Information.................. 7,8
Monitor Specifications .................. 3 Play Instruction ...................-00005 8
Monitor Information..................... 4 Dip Switch Setting....................0- 9
Wiring Harness Color Code............... 5 User Information Warning. ....... Back Cover
CONVERSION KIT CONTENTS:
¢ MAIN PRINTED CIRCUIT BOARD ¢ P.C.B. CAGE (FCC REQUIRED) ¢ CONNECTING WIRING HARNESS ¢ 6 SETS — BUTTON ASSEMBLIES ¢ TWO 8-WAY JOYSTICKS ¢ MARQUEE (HEADER) (1/8” acrylic sheet) ¢ ONE SET SIDE PANEL GRAPHICS (left & right) ¢ CONTROL PANEL OVERLAY ¢ CONTROL PANEL DECALS instruction decals/button decals (2 sets) ¢ MANUAL REGISTRATION CARD
REPLACEMENT ACCESSORIES ARE AVAILABLE THROUGH YOUR DISTRIBUTOR.
THIS KIT USABLE FOR COCKTAIL AND UPRIGHT VIDEO GAMES WITH A RASTAR SCAN MONITOR WHICH IS OR CAN BE MOUNTED HORIZONTALLY.
LIFE FORCE INTRODUCTION
i
KONAMI CONVERSION KITS are the most complete conversion kits available today. Every detail has been carefully considered, designed and packaged to provide you the means of easily producing a professional conversion.
These kits have all the accessories to easily convert your UPRIGHT or COCKTAIL video game.
We strongly urge you to FULLY STUDY this instruction manual BEFORE you begin your conversion. It contains step-by-step instructions, schematic diagrams and suggestions on how to install your Konami Conversion Kit and maximize your profits. LIFE FORCE can be installed in any horizontally mounted rastar scan monitor game.
Everything you will need to construct your new game is provided in this kit. All accessory parts—wiring harness, joystick, etc. are custom made for LIFE FORCE by top engineers experienced in the coin-op industry. Two 8-way joysticks (as provided) MUST be used.
The Player Instruction and Button Control decals are made of a non-destructible acrylic material specifically to keep the player from peeling them off. Should you convert a cocktail table game, LIFE FORCE is supplied with 2 sets of button decals.
- * * IMPORTANT NOTICE x x x
The Japanese Amusement Machine Manufacturers Association (JAMMA) has introduced a new standard in video game P.C.B.’s. It was decided that all new products from any JAMMA member will use the same pin print-out on the edge connector. The edge connector will have 56 pin outs, 28 per side.
Konami Inc. will offer a 56 to 36 pin adaptor P.C.B. available through your distributor. This new adaptor P.C.B. will enable the new 56 pin out to adapt to Konami’s old standard 36 pin out.
- * * STEREO SOUND x x x
LIFE FORCE offers stereo sound in this kit. Please see page 7 for proper installation.
PUTTING YOUR BEST GAME FORWARD
PREPARATION: For best results, all old graphics should be removed completely from the cabinet. “Stick-on” graphics can be removed by using a hairdryer or hot air device. The heat from the dryer will loosen the adhesive, allowing you to easily peel them off — any adhesive residue can be cleaned off with acetone and a soft dry cloth. (DO NOT USE ACETONE ON SURFACES PAINTED WITH FLAT PAINT.) TOOLS YOU NEED: 1, Foaming Aerosoi (such as “Windex”’).
- Soft Squeegee.
- X-Acto Knife.
SIDE PANEL DECALS
- Spray area of cabinet where Side Panel decals are to be applied with foaming aerosol or a mild soap solution. . Remove protective backing from decals. . Position decals into place. . With a soft squeegee, beginning from the center of the decal, slowly and evenly press out excess foam until you achieve a smooth finish.
- Allow to set approximately 2 to 3 hours before handling. Maximum adherence is achieved in 48 to 72 hours. PON
- Trim side decal to fit your cabinet.
CONTROL PANEL OVERLAY:
- Refer to Recommended Control Panel Layout on page 1.
- Drill any new holes needed.
- Plug any holes that will not be used. (A permanent epoxy filler works well for this step.)
- Pre-position the overlay prior to removing the backing.
- Slowly apply the overlay — inch by inch on the control panel, removing the backing as you apply it.
- Once it's in place, by using an X-Acto knife, cut around the button and joystick placements.
INSTRUCTION/BUTTON DECALS: Apply the Player Instruction, Button and 1 Player/ 2 Player decals in their respective positions. Apply pressure liberally. Allow to set as long as possible before putting game on location.
FCC WARNING LABEL: FCC Warning Label must be applied to the outside of the cabinet near the line cord entry.
MARQUEE
(WEAR PROTECTIVE GLASSES WHILE TRIMMING MARQUEE)
1/8” Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this is done.
One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish).
CUTTING WITH A KNIFE OR SCRIBER Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind — a scribing knife such as the one pictured, a metal scriber, an awl, or even a sturdy craft knife — to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.
Always draw the scribing Break sheet over edge of knife along a straight edge. table after scribing
P.C.B. CAGE INSTALLATION
Konami, Inc. now supplies a new style P.C.B. cage which is superior to old style cages because of ease of installation. The cage is made of a 32 point stem-stock which is fire retardant. TO INSTALL THE CAGE:
- Open cage bottom and secure to desired P.C.B. position.
- Install printed circuit board inside cage using wood screws, screwed through the cage bottom into cabinet side.
- Close the cage over printed circuit board and secure with latch on cage.
LIFE FORCE: MONITOR SPECIFICATIONS
LIFE FORCE requires a horizontally mounted monitor. It also generates composite negative sync. If your monitor is composite positive sync, you will have to change to composite negative sync.
- To alternate composite positive sync to composite negative sync, use 7404 IC or 74LS04 IC. The signal on the output pin from the P.C.B. is a combination of H-sync and V-sync.
FIGURE 2: a
FROM P.C. BOARD
NEGATIVE COMPOSITE SYNC. OUTPUT TO MONITOR (PIN 14 on P.C.B EDGE) POSITIVE COMPOSITE SYNC.
(+5V and GND should be taken out of the P.C. Board.)
- Separate Sync modification for LIFE FORCE if your monitor has “Separate Sync” input. (For example “Electrohome brand” and Wells-Gardner brand.”) Step 1 WIRING HARNESS
LaEv
H MONITOR BOARD
NEGATIVE SYNC INPUT VIDEO SYNC
If the picture is still not stable... Step 2 Prepare Hook-up wire to seperate -H and -V sync. signals.
WIRING HARNESS
Fel VIDEO SYNC Lul-v] NEGATIVE SYNC INPUT
PWB201012 CN4
LIFE FORCE: MONITOR INFO.
SERVICE INSTRUCTIONS
1.0 BLACK LEVEL CONTROL ADJUSTMENT This control has been set at the factory and should not need further attention, however, when the game is connected a slight adjustment of VR201 may be necessary to obtain the proper black level (the black portion of the picture just extinguished).
2.0 VERTICAL SIZE (HEIGHT) Location of this control is shown in Fig. 1. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct vertical proportions.
3.0 CIRCUIT PROTECTION A 4.0A pigtail fuse, mounted on the Main Board has been provided to protect the Power Output Circuit.
4.0 FOCUS Adjust the focus control, located on the HV unit (T352), for maximum over-all defination and fine picture detail.
5.0 HORIZONTAL HOLD CONTROL ADJUSTMENT, VR351 (See Fig. 1) A warm-up period of at least five minutes should be allowed before alignment is carried out. With the monitor being driven from the game signal, short TP601 to TP31. Adjust VR351 until the picture stops sliding horizontally. Remove the short.
6.0 HORIZONTAL VIDEO POSITION If the video is off center on the raster some compensation can be made by adjusting this control.
7.0 VERTICAL RASTER POSITION ADJUSTMENT If the video is off center vertically, (short dimension of picture tube) some compensation can be made by moving the vertical raster position adjustment jumper to either positions “U” or “D”.
8.0 HORIZONTAL RASTER POSITION ADJUSTMENT If the video is off center horizontally (long dimension of the picture tube) some compensation can be made by moving the horizontal raster position adjustment jumper either positions “R" or “L”. 9.0 HORIZONTAL WIDTH ADJUSTMENT The horizontal width coil is a hexagonal tuning tool adjustment. This control must be adjusted slowly, if necessary, until the picture or test pattern attains the correct horizontal proportions.
- KONAMI GAMES ARE ALL NEGATIVE COMPOSIT SYNC. USE THE THREE PIN CONNECTOR ON THE MONITOR.
—_ RED DRIVE GRN yg rive "9
RED CUTOFF GRN CUTOFF: BLU CUTOFF
*NEG H SYNC
HORIZ HOLO
BLK LEVEL
HORIZ VERT VERT VERT HORIZ CENTERING SIZE HOLD RASTER RASTER SHIFT SHIFT
FIGURE 1
LIFE FORCE: WIRING HARNESS
Solder Side +» Parts Side WIRE COLOR KEY:
BLACK GND] A 1 GND BLACK
| BLACK | GND] | B | 2 | GND | BLACK | |
| RED | +5VDC| | C | 3 | +5V DC | RED |
| RED | +5VDC|} | D | 4 | +5V DC | RED |
(EMPTY) | E 5 | (EMPTY)
| ORANGE | +12VDC) | F | 6 | +12V DC | ORANGE |
| *KEY | H | 7 | *KEY | |||
| WHITE/RED COIN COUNTER 2| | J | 8 | COIN COUNTER 1 | WHITE/BLACK |
(EMPTY) | K | 9 | (EMPTY)
| WHITE/GREEN = (Mono Speaker Output) | L | 10 | (Mono Speaker Output) | WHITE/BLUE |
(EMPTY) | M 11 | (EMPTY)
| GREEN/WHITE | VIDEO GREEN | N | 12 | VIDEO RED | RED/WHITE |
| WHITE | VIDEO SYNC | P | 13. | VIDEO BLUE | BLUE/WHITE |
| YELLOW/BLACK | SERVICE SW | R | 14 | VIDEO GROUND | BLACK |
NOTUSED} S | 15 | NOT USED
| YELLOW/RED | COIN2| | T | 16 | COIN1 | YELLOW/BLUE |
| WHITE/VIOLET | 2P START | U | 17 | 1P START | ORANGE/BLACK | |
| WHITE/BROWN | 2PUP|] | V | 18 | 1P UP | WHITE/GRAY |
| ORANGE/WHITE | 2P DOWN | W | 19 | 1P DOWN | YELLOW/GRAY | |
| ORANGE/RED | 2PLEFT|) | X | 20 | 1P LEFT | YELLOW/GREEN |
| ORANGE/GRAY | 2P RIGHT | Y | 21 | 1P RIGHT | ORANGE/BLUE | |
| GRAY/RED | 2P SHOOT} | Z | 22 | 1P SHOOT | GRAY/BLACK |
| GRAY/GREEN | 2P MISSILE | a | 23 | 1P MISSILE | GRAY/BLUE |
NOT USED | b 24 | NOT USED
| NOT USED} | c | 25 | NOT USED | ||
| NOT USED| | d | 26 | NOT USED | ||
| BLACK | GND| | e | 27 | GND | BLACK |
| BLACK | GND | f | 28 | GND | BLACK |
(BASE COLOR/LINE COLOR)
*Cocktail Table or Dual Control Upright Only
cd LIFE FORCE
WIRING DIAGRAM
c SapAET INOT APPLICABLE | 2A REQUIRED POWER CAPACITY | aye
Nate oAtew aa iew
r 1) SPEAKER LEFT +
| —-_— 2 SPEAKER LEFT - 1 | 13) sr aner aiGHT -
pode 14] SPEAKER RIGHT +
| JST 4PIN POST W/BASE | BaP -SHF-1 254M PICTH | PARTS SIDE — -—SOLDER sive “4H
Bac ay
| FUSE 78 | POWER | FUSE 2A | | 3 | c3 Incounrer 1 | mma r a we TOIN COUNTER | RED — | corn cauNTeR 2 | — =n COIN COUNTER2 . ws, ;
COLOR MONITER — aLuE a | | | RED 15 L Lae ee CONTROL FOR 2P rm rm | ] SYNC Hi i VIDEG GND coTNt SERVICE| = eeu | ze 7 eel a, COIN! ee 1p start | COIN2 L 12 START TT) 2p START |
To 1° up 22 UP is; 1P DOWN —=1 1) 2P DOWN ~) 2P LEFT er Pp
2P RIGHT
BET iP SHOOT 2p 1p
22 uP | (2P_DGWN i
2° LEFT
SAME AS iP CONTROLS ("28 RIGHT | 2° SHOOT 1Peme 2° MISSILE |
r SHOOT MISSILE 2P MISSILE | GND | GNO |
GNO ae) |
CONTROL FOR 1P LOsnl MISSILE Jord ie SHOOT RIGHT wp CNN | JAMMA S6PIN EDGE CONNECTOR 5/32 INCH PITCH
LIFE FORCE: TECHNICAL INFORMATION
IS THE HORIZONTAL SCAN ON YOUR MONITOR TOO SMALL?
Most of the Wells-Gardner monitors in the field are set for an active video signal of 50 micro seconds. Konami’s LIFE FORCE active video signal is 40 micro seconds. Therefore if the horizontal scan is too small, an adjustment of the monitor is recommended. This may be solved simply and inexpensively. (Refer to your Wells-Gardner schematic.)
- Change capacitor C365 on the monitor to .15 mf 200V polypropolene.
- Add an 820 PF. 1500V polypropolene capacitor across the horizontal output transformer Q352 from the collector to the emitter.
- Cut the horizontal centering wire #30. (Usually yellow in color.)
STEREO/MONO SOUND INSTALLATION
Konami introduces stereo sound. Please read instructions carefully. If your video cabinet doesn’t utilize two speakers, follow instructions for mono output.
TECHNICAL INFORMATION
Adjusting Sound Volume In stereo specifications, adjust volume of each speaker separately (L and R). PCBIB) in monaural specifications, use R-volume switch to | =| adjust volume. L-volume switch is irrelevant to volume. By R VOLUME. VOLUME NB L MONO, fo) 5 OSM 56° EDGE CONNECTORIJAMMA) ° HOW TO CHANGE TO MONAURAL/STEREO
*Note: Mono & Stereo sound cannot operate simultaneously. Not | | Noo (SOLDER-SIDE) | | (PARTS-SIDE) For Mono Sound | Use pin #10 and of the 56 pin edge connector to the B . speaker contacts. c = MONAURAL Also connect Jumper connector into CN3. STEREO SPEAKER SPEAKER
For Stereo Sound Use connector CN5 as your speaker output ports connect pins 1 & 2 to the left speaker pins 3 & 4 to the right speakers. Also connect Jumper connector to CN2.
LIFE FORCE: TECHNICAL INFORMATION
- Required Power Capacity
+5V DC 7A or more.
+12V DC See Figure 1 below.
Figure 1:
Required Power Capacity
- Signal output R(red) analog, positive a G(green) analog, positive i an Bi(blue) analog, positive WW wa Sync. H-V composite negative a v
PLAY INSTRUCTION SELF TEST
For one or two players. Player can enter at any time. 3 ships per credit. Each coin slot can accept up to 9 credits per play. To continue, insert coins BEFORE you lose your last ship. (Note: The number of player's ships and the maximum credits per play can be changed by Dip Switch Settings.)
Move your space ship by 8-way joystick. Destroy enemies by “Shoot” button. Pick up the parts to increase your power. « SPEED UP Five speed levels. ¢ MISSILE Press “Missile” button to launch. ¢ LASER Your forward rockets turn to deadly lasers.
- RIPPLE LASER _ Use “Shoot” button to fire. « FORCE FIELD Protect your ship with barriers. ¢ MULTIPLE Increase your fire power by up to 4 times as much.
You can obtain multiple special powers but you cannot have LASER as well as RIPPLE LASER. A. How to start
- Turn on the SWS of the DIP SW3. B. Test Items
- Conditioning of Picture Contortion
- Color Conditioning
- Control Check
- Coin Counter Check
- DIP SW SET
- Sound Check
*To change items, push 1P start button.
SHOOT MISSILE
DIP SWITCH SETTINGS
DIP SW No. 1 Settings Coin 1 Switch Set Coin 2 Switch Set
| sw | 4 | 3 | 2 | 1 [| CoN] PLAY] | sw | 8 | 7 | 6 | 5 | COIN | PLAY |
| «© | OFF | OFF | OFF | OFF | 1 | 1 | ; «| | OFF | OFF | OFF | OFF] | 1 | 1 | ||||
| OFF | ON | 1 | 2 | OFF | ON | 1 | 2 | ||||
| ON | OFF | 1 | 3 | ON | OFF | 1 | 3 | ||||
| ON | ON | 1 | 4 | ON | ON | 1 | 4 | ||
| OFF | ON | OFF | OFF | 1 | 5 | OFF | ON | OFF | OFF | 1 | 5 | ||||
| ‘| OFF | ON | 1 | 6 | OFF | ON | 1 | 6 | ||||
| ON | OFF | 1 | 7 | ON | OFF | 1 | 7 | ||||
| ON | ON | 2 | 1 | ON | ON | 2 | 1 | ||
| ON | OFF | OFF | OFF | 2 | 3 | ON | OFF | OFF | OFF | 2 | 3 | ||||
| OFF | ON | 2 | 5 | OFF | ON | 2 | 5 | ||||
| ON | OFF | 3 | 1 | ON | OFF | 3 | 1 | ||||
| ON | ON | 3 | 2 | ON | ON | 3 | 2 | ||
| ON | ON | OFF | OFF | 3 | 4 | ON | ON | OFF} | OFF | 3 | 4 | |
| OFF | ON | 4 | 1 | OFF | ON | 4 | 1 | ||||
| ON | OFF | 4 | 3 | ON | OFF} | 4 | 3 | |||||
| : | ON | ON | FREE PLAY | ON | ON | INVALIDITY |
DIP SWITCH NO. 2 SETTINGS THE NUMBER OF PLAYER'S LIFE SOUND IN ATTRACT MODE
| sw | 1 | 2 | NUMBER | sw | 8 | SOUND |
| OFF | OFF | 2 | OFF | OFF | |||
| . | ON | OFF | 3 | « | ON | ON |
OFF | ON 5 ON | ON 7 NUMBER OF COIN SLOTS
| sw | 3 | NUMBER |
OFF SINGLE
| ON | TWO (SEPARATE) | DIP SWITCH NO. 3 SETTINGS |
MAXIMUM CREDITS FOR CONTINUATION Video Sereen Flip
| sw | 4 | 5 | MAXIMUM NUMBER | Sw | L | |
| ore. | OFF | 1 | «| | OFF | NORMAL | ||
| on | ocr | 7 | ON | UPSIDE DOWN | |||
| OFF | ON | 5 | MANUAL TEST | ||||
| v | ON | ON | 9 | sw | 3 | MODE |
| DIFFICULTY OF THE GAME | ~ | (Shr | GAME:PLAY | |||
| sw | 6 | 7 | DIFFICULTY | ON | BSL | ||
| OFF | OFF | EASY | CHANGE OF TABLE OR UP-RIGHT | ||||
| . | ON | OFF | NORMAL | sw | 4 | TYPE | |
| OFF | ON | DIFFICULT | OFF | TABLE | |||
| ON | ON | VERY DIFFICULT | = | ON | UP-RIGHT |
- Shows normal setting *SW 2 NOT USED 9
rrr
USER INFORMATION
WARNING
F.C.C. REGULATION COMPLIANCE
THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE- QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.
IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER- FERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.
THE P.C. BOARD CAGE SUPPLIED WITH THIS CONVERSION KIT MUST BE UTILIZED AND TERMINATED TO GROUND AT THE TIME OF INSTALLATION.
yp KONAMI.
815 Mittel Drive, Wood Dale, Illinois 60191 Telephone: (312) 595-1443, Telex: 6871385 KONAM UW, Fax: (312) 595-2973 For Technical Assistance Call Toll Free (800) 222-6181 (Outside Illinois)