CATHODE RAY TOMES

Gun Service Package

Light gun game (specific title not identified) (Nintendo) · Document · 6 pages · 2 sections · original scan

Page 1

GUN SERVICE PACKAGE

1-800-633-3236 ee 1-206-882-2040

Page 2

GUN_ DISASSEMBLY

  • Refer to the Parts List and Breakdown for any Part names.

1.

2.

10.

Lay gun flat with all ten (10) (LH) bolt heads upward. SEE FIG, 4

Loosen the nine (9) LH bolts that are recessed in the gun housing until the nuts fall from the bottom shell. Leave bolts in holes. : Tren Remove the one (1) remaining LH bolt holding the grip band to the base of the gun. The nut is welded in place. Slide grip band down over the gun cable and remove.

Carefully remove upper half of gun shell. Leave all bolts in their holes and set shell aside.

Remove lens.

To reassemble, follow Steps 1-5 in reverse order. Make sure that none of the wires gets pinched between the two shells during reassembly. TO REMOVE GUN CABLE

First refer to disassembly procedure. rem "4, Fig 2

Remove LH bolt attaching the chain to the frame collar. Spread the frame collar and slide off the grip frame.

Loosen all four (4) set screws on bottom of grip frame with a 5/64" Allen wrench.

Turn the grip frame until a fifth set screw (on top of the grip frame) is upward. Loosen this one also.

Remove the four (4) wires with slide terminals on top of the swivel contact assembly. Attach them together in pairs as shown in Figure A. (This will help reassembly.)

Pull cable from gun, feeding the wires through the center of the swivel contact assembly. The swivel contact assembly does not need to be removed.

Remove the red and white connectors from the opposite end of the gun cable by gently pushing down the retaining tabs as shown. Be sure to note the wire color code.

Pull wires through inside of cable. Visually inspect wires and check for continuity on all four wires. If any one wire does not check good for continuity, replace entire wire assembly.

Replace cable if necessary.

To reassemble, follow Steps 1-8 in reverse order. The fifth set screw (on top of the grip frame) should set properly into the cord stop collar.

Transfer chain to new cable. Be sure to leave slack in the cable between the base of the gun and the first chain ring frame. This removes the cable stress from the base of the gun.

Page 3

TO REPLACE SWIVEL CONTACT ASSEMBLY

  • First refer to disassembly procedure.
  • Remove the four (4) wires attached to terminals at the top of the swivel contact assembly. Attach them together as shown in Figure A. (This will help reassembly.)
  • Remove the two (2) small screws mounting the swivel contact assembly to the lower shell. These screws are threaded into the plastic shell. Be sure not to strip these threads. The gun cable does not need to be removed. Just lift swivel contact assembly and wires will slide through the center.
  • Desolder the five (5) wires attached to the four swivel contacts.
Note the wire color coding for each contact. (See Figure C.)
  • The swivel is a very delicate unit. Hold by grey plastic frame only. Avoid turning when not mounted firmly in place.
  • Inspect through the clear shield. Verify that there is:

A) One (1) large contact on the top of each plate. B) Four (4) small contacts on the bottom of each plate. C) Continuity from the four (4) top terminals to each assigned side contact. If it doesn't check good, replace swivel contact assembly.

  • Reassemble by following Steps 1-3 in reverse order.

TO REPLACE TRIGGER SWITCH ASSEMBLY

  • First refer to disassembly procedure.
  • Remove trigger assembly from shell.
  • Desolder two (2) wires attached. (Note color coded wires. See Figure D.)
  • Replace assembly in reverse order Steps 1-2. Be sure to insert pegs into proper holes.

TO REPLACE P.C. BOARD ASSEMBLY

  • First refer to disassembly procedure.
  • Remove P.C.B. assembly and ground plate from shell.
  • Desolder three (3) wires attached. (Notice color coding marked on P.C.B.)
  • Replace in reverse order of Steps 1 and 2. Be sure to place P.C.B. on top of both retaining tabs so that it sits firmly.
Page 4

TO REPLACE OUTER SHELLS

If just upper shell (left shell) needs to be repaired, follow disassembly Steps 1-4 and replace. Note Step 4 below.

If the lower shell (right shell) needs to be repaired, follow disassembly Steps 1-5.

Remove the two (2) screws that mount the swivel contact assembly to the lower shell. These screws are threaded into the plastic shell. Be sure not to strip threads.

Inspect all parts for breaks or chips. If necessary, replace.

Transfer all parts to new lower shell and reassemble. If unsure about installation of any part, refer to instructions on that specific part.

wai Fae z28 228 o> aor

FY PUSH TAB DOWN

PULL WIRE

(FIG. A) (FIG. B)

BROWN & RED

WHITE

BLUE

VIOLET

(FIG. C) (FIG. Dy

Page 5

le nin HOOK

GUN CABLE ASSY. Completed

(FIG, 2)

Item Number Part Number Description

1MDSG2-11-16Gun Frame Collar
2MDSG2-11-21Chain Frame Collar
3MDSG2-11-17Gun Chain Hook
4MDSG2-11-20Security Chain
5MDSG2-11-11Grip Frame
6MDSG2-11-13Cord Stop Collar
7MDSG2-53-14Nut M3
8MDSG2-54-11Flat Washer M4.5

9 Double Back Tape

10MDSG-14-03Flexible Tube
11MDSG2-11-19Chain Ring Frame
12MDSG-14-04Gun Harness (inside tube)
13MDSG2-51-15LH Screw (nickel)
14MDSG2-51-16Set Screw
15MDSG2-51-17Set Screw
16MDSG2-51-14LH Screw (nickel)
17MDSG2-53-12Flange Nut M3 (nickel)
18MDSG- 63-13Control Panel Chain Hook
19MDSG2-41-10Swivel Contact Terminal Connector
Page 6

Item Number

UPwNP

Be FPODMYD Part Number

MDSG2-12-11 MDSG2-12-12 MDSG2-13-11 MDSG2-10-01 MDSG2-10-03 MDSG-14-14 MDSG- 34-11 MDSG-51-11 MDSG-51-12 MDSG-53-11 MDSG-53-12 MDSG2-10-02 MDSG2-11-18 MDSG2-51-11 MDSG2-51-12 MDSG2-51-13 MDSG2-53-15 MDSG2-09-00 (FIG. 1) SEE FIG. 2

Description

Gun Housing (left) Gun Housing (right) Lens Gun PC Board Assy Trigger Assy Trigger Spring (trigger assy) Micro Switch (trigger assy) Machine Screw (trigger assy) Machine Screw (trigger assy) Cel-Flange Nut (trigger assy) Nut M2.3 (trigger assy) Swivel Contact Assy Grip Band LH-3 Screw (black) LH-3 Screw (black) LH-3 Screw (black) Nut M3 (black) LH Tool