CATHODE RAY TOMES

Kickman Parts and Operating Manual (Dec 1981)

Kick (upright) (Midway, 1981) · Parts & Operating Manual · 118 pages · 45 sections · original scan

Page 1

DECEMBER, 1981 Game Nos, 968, 513, 515

MIDWAY’S

No. 515 COCKTAIL

No. 968 UPRIGHT

MIDWAY MFG. CO. A BALLY COMPANY

10750 W. GRAND AVENUE FRANKLIN PARK, ILLINOIS 60131 No. 513 MINI Heck. USA

Phone: (312) 451-1360 Cable Address: MIDCO ‘Telex No.: 72-1596

Form No. 0968-00300-C000

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment Generates, Uses and can Radiate Radio Frequency Energy and if not installed and used in accordance with the Instructions Manual, may cause interference to Radio Communications. As temporarily permitted by Regulation it has not been tested for compliance to Subpart J or Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a Residential Area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

OS REE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

EX o

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU _UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

MIDWAY MFG. CO.

Snuites You Jo Use our TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER MIDWAY GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS. Continental U. §. 800-323-7182 Mlinois Only 1-800-942-0497

COPYRIGHT 1981 ©BYMIOWAYMFG.CO. ALL RIGHTS RESERVED.

NO PART OF THis PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. FOR PERMISSION REQUESTS, WRITE: MIOWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131

Printed in U.S.A.

Page 3

TABLE OF CONTENTS

DESCRIPTION PAGE Introduction 2.2.2.6... 66 cece ec een ete eee nen e tent e nee tenet ttt eee e ee 1-1

Location and Setup Inspection ... Installation. Self Test..... Game Volume Adjustment Control Option Settings ... Game Operation .. Self Test Mode Attract Mode.... Ready to Play Mode. Play Mode ae Two Player Operation 22... 0... ccc cece een e tet eee been eee e ne eee 2-15

Maintenance and Repair Cleaning... Fuse Replacement .. Opening the Control Panel Removal of Main Display Glass and T.V. Bezel .. T.V. Monitor Replacement Printed Circuit Board (P.C.B.) Replacement. Opening the Attraction Panel os Coin Door Maintenance ........ 6... cece cece nent t een ene teeter n eee n enna ee

Illustrated Parts Breakdown Ball Control Assembly — All Versions . Ball Control Assembly — All Versions — No. 968 — Kick-Man Upright — Front............ No. 968 — Kick-Man Upright -- Front — Parts List No, 968 — Kick-Man Upright — Rear Access No. 968 — Kick-Man Upright — Rear Access — Parts List No. 513 — Kick-Man Mini — Front oe No, 513 — Kick-Man Mini — Front — Parts List . No. 513 — Kick-Man Mini — Rear Access ...... No. 513 — Kick-Man Mini — Rear Access — Parts List . No. 515 — Kick-Man Cocktail — Front . No. 515 — Kick-Man Cocktail — Front — Parts List No. 515 — Kick-Man Cocktail — interior Access .. No. 515 — Kick-Man Cocktail — Interior Access — Parts List. Kick-Man — All Versions — Not Shown List Kick-Man Upright — Header Fluorescent Fixture Assy . Kick-Man Upright — Header Fluorescent Fixture Assy — Parts List .. Filter Assy .........- Filter Assy — Parts List Front Door Assy — U.S.A. 25¢ Front Door Assy — U.S.A. 25¢ — Paits List...

Technical Troubleshooting... Introduction . General Suggestions .. Harness Component Troubleshooting . Transformer and Line Voltage Problems . .

Page 4

DESCRIPTION

Vi.

Vi. TABLE OF CONTENTS (cont'd)

A Glossary of Microprocessor Terms .. Introduction to the Z-80 CPU General Purpose Registers .. Arithmetic and Logic Unit (ALU) ... Instruction Register and CPU Control . Z-80 CPU Pin Description .......... MCR II System P.C. Board Jumper Options. . Kick-Man — All Models — Sound I/O Board EPROMS — Version 1... Kick-Man — All Models — Sound !/O Board EPROMS — Version 2. Kick-Man — Upright — CPU EPROMS — Version 1... Kick-Man — Upright — CPU EPROMS — Version 2. Kick-Man — Mini & Cocktail — CPU EPROMS — Version 1 Kick-Man — Mini & Cocktail — CPU EPROMS — Version 2 Kick-Man — Upright — Video Generator EPROMS — Version 1 Kick-Man — Upright — Video Generator EPROMS — Version 2 Kick-Man — Upright — Video Generator EPROMS — Version3 .. Kick-Man — Mini & Cocktail — Video Generator EPROMS — Version 1. Kick-Man — Mini & Cocktail — Video Generator EPROMS — Version 2 . Kick-Man — Mini & Cocktail — Video Generator EPROMS — Version 3

T.V. Monitor Manual .. . Introduction ... Symptom Diagnosis .. Guide to Schematic Symbols Troubleshooting Theory of Operation Differences Between Monitors . Parts Interchangeability ....... Wells-Gardner Monitor Schematic — 19”......... Wells-Gardner Monitor Replacement Parts List — 19' Electrohome Monitor Schematic — 19”........... Electrohome Monitor Replacement Parts List — 19”. Electrohome Monitor Schematic — 13”.........-. Electrohome Monitor Replacement Parts List — 13”...

Schematics and Wiring Diagrams Wiring Diagram — Upright. Wiring Diagram — Mini.. Wiring Diagram — Cocktail .. Power Supply P.C.B. — Component Layou' Power Supply P.C.B. — Schematic ........ Video Generator P.C.B. — Component Layout Video Generator P.C.B. — Schematic. . CPU Board — Component Layout CPU Board — Schematic Sound I/O Board — Component Layout . Sound |/O Board — Schematic ......... Dual Power Amp Board — Component Layout Dual Power Amp Board — Schematic . Binary Angle Decoder P.C.B. — Component Layout. Binary Angle Decoder P.C.B. — Schematic

Page 5

TABLE OF FIGURES

FIGURE PAGE

1 Assigned point values 4-2 2 Location of serial number, interlock switch, ON/OFF switch & major sub-assemblies 2-2 3 Major sub-assemblies (cont. from Fig. 2) . 2-3 4 Interlock switch operation ............. 2-4 5 Location of volume control, self test switch & service credit switch -4 6 Option switch settings 6a Option switch location ... 7 Game operation. 8 Seif test display . 9 Cross hatch pattern .. . 10 Location of hardware master reset switch . 2-10 1 Location of fUSES...... 6... e eee eee eee .3-1 12 Removing control panel — Upright game. .3-2

  • Removing control panel — Mini game.. 3-3 14 Opening Cocktail game .............45 68-3 15 Removing control panel — Cocktail game .. 13-4 16 Removing display glass — Upright game .
  • Removing bezel — Upright game ...... 18 Removing display glass — Mini game .. 19 Removing bezel — Mini game 20 Removing monitor — Upright game 21 Removing monitor — Mini game . 22 Opening Cocktail game . 23 Removing monitor — Cocktail game ... . 24 Replacing power supply P.C.B. — All versions . 3-8 25 Replacing card rack P.C.B.’s — All versions +3-9 26 Removing attraction panel — Upright game . 3-9 27 Replacing fluorescent starter — Upright game . . 3-10 28 Replacing fluorescent light mounting bracket — Upright game - 3-10 29 Replacing speaker — Upright game .... . 3-10 30 Removing attraction panel — Mini game . 3-11 31 Replacing speaker — Mini game wee B14 32 Removing coin acceptor wee B12 33 Opening the metal coin acceptor. . 3-12 34 Lubricating the metal coin acceptor » 3-13 35 Reinstalling coin acceptor .. . 313 36 Opening the plastic coin acceptor. . . 3-14 37 Changing the plastic coin acceptor to accept American or Canadian quarters... 23-14
Page 6

Kick-Man

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and II of this manual completely. It will not take more than a few minutes and it may be very helpful.

I. Introduction

KICK-MAN is a one or a two player game. There are three models: the “UPRIGHT”, “MINI”, and “COCK- TAIL TABLE”. The Upright and Mini models have been designed for either RIGHT or LEFT hand use. When the two player mode is selected on the Upright or Mini model, the players take turns at the controls to take the Clown through the game course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it's your turn. When playing this game, the Clown is under YOUR control. YOU make him move back and forth across the screen to Kick, Pop, or Catch the falling balloons. Whether he catches them or pops them depends on what rack you are in. These balloons are displayed in groups, called “racks”, across the top of the screen. The first rack is made up of 16 balloons. The second and all future racks are made up of 24 balloons each. The balloons are assembled ina random order and are dropped in a random order by the game. YOU position the Clown under the falling balloons to either catch them on his head or pop them with the pin in his hat. If you miss the balloon and are close enough, you can KICK it back up in the air again and give yourself another chance to get under it before it hits the ground, If a balloon does hit the ground, the Clown falls off his unicycle and you give up one player. When your NEXT player appears, he will begin with NO balloons on his head. YOU MUST START OVER AGAIN FROM THE BEGINNING TO STACK UP BALLOONS FOR POINTS. As your skill level increases, the number of fast falling balloons is increased (BLUE — fastest falling; RED — medium; and YELLOW — slowest falling), the balloons will begin to fall at an angle — not straight down as in earlier racks, and as you kick one balloon up — sometimes another begins its fall (you then have TWO balloons in the air at the SAME time). However, you can NEVER have MORE than two balloons in the air at the SAME time.

Bonus Clowns are awarded to you periodically throughout the game as you reach or pass certain preselected point values. Each balloon and rack identifier symbol has an assigned point value as listed in Figure 1.

Major New Features

There are several major new features in your KICK- MAN game; 1) During regular play, you can kick a missed balloon back up in the air numerous times and give yourself another chance to get under it to build up a full stack of eight balioons; 2) If you missa balloon or catch a bomb when you are in a CHAL- LENGE rack, causing the Clown to fall off his unicycle, you ARE NOT PENALIZED ONE PLAYER

  • ali that is lost are the balloons that were stacked on the Clown’s head; 3) The PAC-MAN will appear three times in the 2nd rack and two times in the 3rd and EVERY succeeding rack when the Difficulty Level option is at the factory recommended setting. As the PAC-MAN eats the balloons on the Clown’s head, you are awarded the bonus points for these balloons right then. This means your Clown does not have to get a full stack of
Page 7

eight balloons before you are awarded the bonus points for them. 4) PAC-MAN BONUS AND SUPER BONUS: A PAC-MAN BONUS (anywhere from 200 to 1600 points) is awarded to the player for each PAC-MAN caught on YOUR Ciown’s head in any one rack. If at the end of that rack, ALL PAC-MEN are still on top of your Clown’s head, a “PAC-MAN SUPER BONUS” of 1600 points is also added to your score;

  • There is a completely new and easy-to-use diagnostic package featuring: a complete ROM/ RAM check with bad chip location information read out on the monitor screen; the capability to check each of the game’s 24 different sounds INDIVID- UALLY; provision for checking each control and switch SEPARATELY; a fuil function Bookkeeping mode; an entire options list that can be set from the front console with NO NEED to crawl inside the back of the cabinet and look for tiny switches located on P.C. boards; a sound system test; and a “PRE-SET”

DESCRIPTION BLUE BALLOON RED BALLOON YELLOW BALLOON

RACK IDENTIFIERS INKY (BLUE GHOST) PINKY (PINK GHOST) CLYDE (ORANGE GHOST) BLINKY (RED GHOST) FALL RATE FAST MEDIUM SLOW 5 category that returns ALL information in the Bookkeeping mode to zero and all operator selected options back to factory recommended settings; and

  • The game is equipped with a rechargeable battery so that it won't forget where it was the night before at closing — even if you turn it off. It will “remember” this information for up to two weeks.

Game Objective

The object of the game is to HAVE FUN while constantly increasing your skill as you play, catching as many balloons as possible each time to get the highest score.

POINTS AWARDED

APPEARS IN RACK NO.

6 and UP

Figure 1 Assigned point values

1-2

Page 8

II. Location and Setup

INSPECTION

. Remove the game from its shipping crate. . Inspect the entire outside of it for any signs of damage. ¢ Any scratches?, dents?, cracks? © Any broken controls? © Any broken glass or plastic?

© Just look it over closely and make a note of any

signs of damage. . Remove the shipping cleats from the bottom of the cabinet. .. Remove the four leg levelers from the coin box and install them, one at each corner of the cabinet. ¢ Level the cabinet. . Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2. ¢ Also check to make sure all plug-in connectors on the wire harness are firmly seated.

NOTE: All connectors or plugs are keyed so they will only go together when all pins are properly lined up. ¢ Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. ¢ Make sure ail printed circuit boards (P.C.B.’s) are firmly seated in their connectors. See Figure
  • These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged. © Note the location of the yame’s serial number. See Figure 2.
  • Check all major subassemblies to be sure they are mounted securely. These are called out in Figure 2 & 3. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power supply filter assembly. Transformer board assembly.

2-1

  • Make a note of any problems that can't be easily corrected.
  • Call your distributor and/or service man about your problem list.

INSTALLATION

  • Location requirements: Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz Temperature: 32° to 100°F (0° to 38°C) Humidity: Not over 95% relative Space required: Upright 25” x 32" (64 x 82cm) Mini 20" x 29" (51 x 74cm) Cocktail 32” x 22” (82 x 56cm) Game height: Upright 72” (183cm) Mini 60” (153cm) Cocktail 29” (74cm)
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game.
Page 9

SERIAL

NUMBERj‘ON/OFF

SWITCH

SERIAL NUMBER

POWER SUPPLY P.C.B.

INTERLOCK

Loaic;SWITCH

BOARDS ret

POWER SUPPLY }} INTERLOCK

FILTER ASSYsuetSWITCH

-~T.V. MONITOR POWER SUPPLY P.C.B. Locic

ON/OFF:TRANSFORMERj-BOARDS
SWITCH:BOARD ASSY‘

. (NOT SEEN) | > TRANSFORMER POWER SUPPLY/ 5. [1 BOARD ASSY FILTER ASSY

SERIAL NUMBER (MAY BE LOCATED |~ ON ANY CORNER) TV. MONITOR

TRANSFORMER ‘ POWER BOARD ASSY oe SUPPLY

(PLAYER 2)

PANEL (PLAYER 1)

LogicSwat'eetPOWER
BOARDSok:tNSUPPLY
ee:a.FILTER ASSY
INTERLOCK\:ON/OFF SWITCH

SWITCH te UNDER TABLE

(INSIDE DOOR) COCKTAIL ON PLAYER 2 SIDE

NOTE: The above photos show a “CARD RACK” assembly installed in the games. Your game(s) will not have a “CARD RACK” assembly.

Figure 2 Location of serial number, interlock switch, ON/OFF switch & major sub-assemblies

2-2

Page 10
  • Interlock and power ON/OFF switches. See Figure 2.
  • To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models).

When any access door is opened, the interlock switch installed there turns off all power to the game.

eCheck each interlock switch for proper operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a

CONTROL PANEL CONTROL PANEL. solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outiet. The game ON/OFF switches for all models are located as shown in Figure 2.Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch.

iS

UPRIGHT

Figure 3 Major sub-assemblies (cont. from Fig. 2)

Page 11

When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 4.

SELF-TEST: Your new game will Self-Test itself to see if ithas any bad parts. The information it receives while testing will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip). GAME VOLUME ADJUSTMENT CONTROL. See Figure 5. The game volume controi pot is located just inside the cabinet on the right side of the coin door frame.

LOCATED INSIDE DOOR There is only one pot. For adjustment, it may be reached through the coin door on ALL models, To make the sounds louder, turn the pot clockwise as you face it (7a). To make the sounds less loud, turn the pot counterclockwise as you face it (a@——™~ ).

Figure 4 Interlock switch operation

SERVICE. CREDIT SWITCH

SELF sur—_| 9 SWITCH

VOLUME ADJUSTMENT

Figure 5 Location of volume control, self test switch & service credit switch

Page 12

Figure 6 Option switch settings

SWITCH NO. 1 — AT B3 — LOCATED ON SOUND I/O P.C. BOARD

DURING GAME PLAY: PLAY MUSIC. DO NOT PLAY MUSIC

MINI COCKTAIL TABLE

FREEZE VIDEO NORMAL OPERATION SWITCH NO. 3 — AT D 1

swt NORMAL OPERATION SOUND I/O DIAGNOSTIC MODE

NORMAL OPERATION RAM/ROM TEST INDICATES TEST RESULTS VIA YELLOW LED ON SOUND I/O BOARD: FAST FLASH = BAD ROM SLOW FLASH = BAD RAM

NORMAL OPERATION OSCILLATOR TEST

NORMAL OPERATION FILTER TEST SW#1 SW#2 SW#3 SW#4 SW#H5 SWHE swe7 Sw#8 SW#9 SW#10 ON NOT NOT NOT NOT NOT OFF USED USED USED USED USED NOT NOT USED USED

  • LOCATED ON SOUND 1/0 (These switches for in shop test use only! ™*SWH2 **SWH3 **SWH4

THE REMAINDER OF KICK-MAN’S MOST COMMON OPTION SETTINGS ARE CONDUCTED DURING THE MACHINE SETUP PORTION OF THE SELF-TEST MODE AND WILL BE COVERED IN DETAIL IN THAT SECTION OF THIS MANUAL.

  • THIS SWITCH NOT USED ON UPRIGHT MODELS. **NO EFFECT IF SW#1 OF SWITCH NO. 3 IS IN THE “OFF” POSITION.

OPTION SETTINGS:

To change the most common option settings, you DO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- Test mode. The Self-Test switch is located just inside the cabinet on the right side of the coin door frame as you face it.

When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you must change one of the switches that is located on one of the game's P.C. boards, it is also recommended that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.)

The P.C. Board option switch settings, and what they will make the game do are shown in Figure 6. See Figure 6a for option switch locations.

2-5

NOTE: in order to set the option switches located on the games P.C. Boards, these Boards MUST be removed from their card rack.

OPTION SWITCH 1

OPTION SWITCH 3:

Figure 6a Option switch location

Page 13

Game Operation

KICK-MAN is a one ora two player game with a color T.V. monitor. The game gives a display which has all the parts shown in Figure 7. The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE INITIAL, AND SELF-TEST. SELF-TEST MODE The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test WILL NOT cause the game to erase any CREDITS it has in its memory when the Self-Test mode is entered. You may begin a Self-Test at any time by sliding the Self-Test switch to the “ON” position after the power to the game is on (the Self-Test switch is located just inside the cabinet on the right side of the coin door frame as you face it). When this is done, the game will react as follows:
  • If the game is in the Attract mode when the Self- Test switch is moved to the “ON” position, it will finish the sequence and then go into the Self-Test mode. This is illustrated by the display of the Self- Test Mode Menue on the monitor screen.

Figure 7 Game operation

2-6

  • If the game is in the Ready-To-Play mode or the Play mode when the Self-Test switch is slid to the “ON” position, it WILL NOT go into the Self-Test mode unti! AFTER the player's Clown has failen off his last unicycle (the game MUST be over). At this point, the game will go into the Self-Test mode. Again, this is illustrated by the display of the Self-Test Mode Menue on the monitor screen.
  • The fastest way to enter the Self-Test mode is to slide the Self-Test switch to the “ON” position and then activate the “TILT” switch located on the back side of the coin door just below the lock mechanism. The game will then IMMEDIATELY go into the Self-Test mode. The Self-Test mode has eight (8) major categories as illustrated by Figure 8.
  • Itis easy to select what category you want to enter. By holding down the ONE or the TWO player button, the Balloon at the left of the screen can be moved UP and DOWN {i=UP) and (ii=DOWN), until it is in front of the category you want to test. Release the button at this time.
  • After the Balloon has been positioned, depress either “KICK” button on the console and the monitor screen wili display the test category you have selected.

Figure 8 Self test display

Page 14
NOTE: There is one exception to this. If you position the Balloon in front of the “PRE-SET” category on the Self-Test Mode Menue, when you press the| “KICK” button on the console — EVERYTHING, | repeat — EVERYTHING, including ALL information in the “BOOKKEEPING” mode and ALL operator selected options, will be set back to zero “0” and to the factory recommended settings — respectively.

© Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST.

  • The next group of Figures (8a through 8h) show the CORRECT screen presentation for EACH category of the Self-Test mode. During the SELF DIAGNOSTICS section of the Self- Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you will see a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from the top down. Third, you will see the screen painted Red, Blue, and Green in bars from the top down. Fourth, all the different colored bars you saw “Second” are displayed again. And fifth, the different colored bars are replaced by this message: “HIT KICK BUTTON TO EXIT”. If the Kick button is not hit, the test will repeat itself. This feature was

Figure 8a Self Test — Sounds

2-7 designed into the game to enable over-night testing for an intermittent hardware problem.

If the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through whatis described above, the game will give you a written message as to which parts are bad. This message includes their |.D.’s and their P.C. Board locations.

During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 8a. © In this category, each of the game’s 24 separate sounds can be checked individually in any order — or — you can tell the game to check them all in order — 3 through 26.

During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 8b. ® In this category, each of the game's player operated controls — including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/contro! is actuated. If no game sound is heard, that switch/control is either not working, miswired, or disconnected. Check it out thoroughly. As the Player Input Switches and Devices are activated, the Switch or Device activated is spelled out in the blank space above “PLAY MUSIC”.

Figure 8b Self Test — Player Input

Page 15

During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like that shown in Figure 8c. @ In this category, a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT”, detailed breakdowns of game times and scores may be obtained. In the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figures 8d and 8e respectively. During the SETUP OPTIONS section of the Self- Test mode, the game will give a display which looks like that shown in Figure 8f. @ In this category, all common game options may be changed from the control console: coins per credit, credits per base, bonus base(s) awarded at, difficulty level — and so on.

Figure 8c Self Test — Bookkeeping

2-8 Figure 8d Self Test — Time Report

Figure 8e Self Test — Score Report

Page 16

During the CHANNEL TEST section of the Self-Test mode, the game will give a display which looks like that shown in Figure 8h. e In this category, the game conducts a test of its SOUND SYSTEM. Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until the Kick button is hit. It then goes back to the Self-Test Mode Menue.

“= Factory recommended settings.

Figure 8f Self Test — Setup Options

DIFFICULTY LEVEL EXPLANATION: SEE FIG- URE 8g. The Difficulty Level setting has a range of 1 to 9. The following Figure 8g shows what effect this option has on the game. Figure 8h Self Test — Channel Test

**NUMBER OF PAC-MEN THAT DIFFICULTY 1ST RACK IN WHICH YOU CAN LEVEL HAVE 2 BALLOONS IN THE AIR CAN APPEAR IN RACK 2

SETTING AT THE SAME TIME AT EACH SETTING

NVYNVNWOOOAA NVYNOwWAAAR be *= FACTORY RECOMMENDED SETTINGS **= THE NUMBER OF PAC-MEN IN EACH SUCCEEDING RACK IS REDUCED BY 1 UNTIL YOU ARE DOWN TO TWO PAC-MEN PER RACK. THESE WILL BE THERE FROM THAT POINT ON.

Figure 8g Difficulty Level Explanation

2-9

Page 17

During the GRID DISPLAY section of the Self-Test mode, the game shows a white cross hatch pattern on the monitor screen. This is for alignment and/or test purposes. This pattern will remain on the monitor screen until the Kick button is hit. The game will then go back to the Self-Test Mode Menue.

To leave the Self-Test mode, simply slide the Self- Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen.

  • RACK ADVANCE: The game can be made to advance through the various racks by beginning a game and THEN sliding the Self-Test switch to the “ON” position. After this has been done, each time you depress the ONE PLAYER BUTTON the game will advance one rack. When you reach the desired rack, slide the Self- Test switch to the “OFF” position. (If you leave the Self-Test switch in the “ON” position, the game will go into the Self-Test mode when you are finished playing the rack you “advanced” to.)

Figure 9 Cross hatch pattern

  • CROSS HATCH PATTERN: SEE FIGURE 9. A cross hatch pattern is shown on the screen when power is first turned on to the game, when the TILT Switch is actuated, during the “SELF DIAGNOSTIC’ portion of the Self-Test mode, and during the “GRID DISPLAY” portion of the Self- Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier. When you are finished using the cross hatch pattern, simply hit the Kick button to return to the Self-Test Mode Menue.
  • HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 10. The function of each of these switches — when pressed — is to make the game think it has JUST been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there is a major problem encountered while testing the P.C. Boards.

Ai

HARDWARE MASTER RESET SWITCH 98688088}

Figure 10 Location of hardware master reset switch

Page 18

ATTRACT MODE

  • The Attract mode starts: e Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) © After a Self-Test has been completed and there are no more credits left in the game’s memory. ¢ After a play has been finished, the score was not high enough to put the game into the High Score/Initial mode, and there are no more credits left in the game’s memory. © After the High Score/Initial mode when there are no more credits left in its memory. e In the Attract mode, the game will give the following respective displays centered on the monitor screen: DISPLAY #1

DISPLAY #2 DISPLAY #3 DISPLAY #4

DISPLAY #5 DISPLAY #6 DISPLAY #7

2-11

Page 19

WER LTELE Epitpen. ay ees be te

DISPLAY #8DISPLAY #9DISPLAY #10

teers: o

DISPLAY #11DISPLAY #12DISPLAY #13

5 puisss

a enna

13 sriess

eS warays

DISPLAY #14DISPLAY #15DISPLAY #16

2-12

Page 20

® No matter where the game is in the Attract mode sequence, it will immediately go to the following display as soon as a game has been paid for. It will hold this display on the monitor screen until the “1 PLAYER” or the “2 PLAYER” start button is pushed.

DISPLAY #1

DISPLAY #2 DISPLAY #3 DISPLAY #4

DISPLAY #5 DISPLAY #6 DISPLAY #7

Page 21

DISPLAY #8 DISPLAY #9 DISPLAY #10

READY-TO-PLAY MODE

  • The Ready-To-Play mode starts when enough coins have been accepted fora 1 or a 2 player game.
  • The Ready-To-Play mode ends when either the “1 PLAYER” or the “2 PLAYER” push button is pressed.
  • In the Ready-To-Play mode, the game will give the previous displays centered on the monitor screen.
  • If no START button is pressed, the game will hold the above ‘Instruction DISPLAY #11 DISPLAY #12 Message” display on the screen indefinitely.

PLAY MODE

  • The Play mode begins when either the “1 PLAYER” or the “2 PLAYER” start button is pressed. When this happens, the following is displayed centered on the monitor screen. Game over PE BLER. 2 your sos RONG

N The Play mode ends when you have no more Clowns left to catch the falling balloons. When this happens, the following is displayed centered on the monitor screen.

2-14

Page 22
  • The game is made up of groups of balloons, called “racks” which are displayed across the top of the screen. These balloons drop in a random order and you move your Clown back and forth to get under them and catch or pop each oneas it comes down. Whether or not your Clown will catch or pop the balloons depends on what rack you are in. The racks of balloons that are displayed one ata time at the top of the screen are made up of PAC- MEN, BLUE BALLOONS, RED BALLOONS, YELLOW BALLOONS, and various rack identifier symbols. Depending on what rack you are playing in, the rack identifier symbols are: 1st and 2nd racks — NONE USED, 3rd rack — INKY, 4th rack
  • PINKY, 5th rack — CLYDE, 6th and ALL succeeding racks — BLINKY.

RATE OF FALL: The BLUE BALLOONS are the fastest falling ones and the YELLOW BALLOONS are the slowest. The RED BALLOONS fall at a speed that is in between the fastest and slowest speeds mentioned above. All rack identifier symbols fall at the same rate as the BLUE BALLOONS.

PAC-MAN: The PAC-MAN will not appear at all in the 1st rack. At the recommended factory settings, he will appear three times in the 2nd rack and two times per rack from the 3rd rack on.

NOTE: The number of PAC-MEN that appear from the 2nd rack on is operator selectable by adjusting the game's level of difficulty. This is done in the “MACHINE SETUP” category of the Self-Test mode. This same level of difficulty adjustment also varies the number of thefirst rack at which youcan have two balloons in the air at the SAME time (when you KICK a missed balloon, another one sometimes begins its fall as the KICKED balloon starts on its way back up).

Normally, the bonus points for the balloons your Clown catches on his head would not be added to your score until your Clown had caught a full stack of eight. But, when the PAC-MAN drops and you position your Clown under him, he will eat all the balloons on your Clown’s head and add their bonus point values to your score at the same time

  • right then and there. You also get a bonus of from 200 to 1600 points for caught PAC-MEN. However, if your Clown should not happen to have any balloons stacked on his head when a PAC- MAN falls, you can kick the PAC-MAN right back up with the balloons again where he will stay fora while before falling again. In this way, you can save your PAC-MEN for later use when you already have some balloons stacked on your Clown’s head. If you should miss a falling PAC-MAN and he hits the ground, this will cause your Clown to fall off his unicycle and you will loose one player. However, you DO NOT lose this “missed” PAC-MAN. When your next Clown and unicycle appear, the “missed” PAC-MAN will also reappear back in his spot among the balloons at the top of the screen. If you have caught one or more PAC-MEN on your Clown's head and you miss a falling object OF ANY TYPE, allowing it to hit the ground and causing your Clown to falloff his unicycle, you lose the PAC-MEN and the chance of getting a “SUPER PAC-MAN BONUS” of 1600 points in this rack. You also lose the bonus points for any balloons and/or rack identifier symbols caught up to the time when your Clown fell. PAC-MAN BONUS POINT SCORING: In a4 PAC- MAN rack, the 1st PAC-MAN on your Clown’s head is worth 200 PAC-MAN BONUS POINTS, the 2nd PAC-MAN on your Clown’s head is worth 400 PAC-MAN BONUS POINTS, the 3rd PAC- MAN on your Clown’s head is worth 800 PAC- MAN BONUS POINTS, and the 4th PAC-MAN on your Clown’s head is worth 1600 PAC-MAN BONUS POINTS. If all 4 PAC-MEN are still on your Clown’s head when the last balloon or rack identifier is eaten, you are awarded an additional PAC-MAN SUPER BONUS of 1600 points. However, if you caught 1 PAC-MAN on your Clown's head, received your 200 PAC-MAN BONUS POINTS, and then fall off your unicycle — losing the caught PAC-MAN and any balloons that were on your Clown’s head at the time of the fall, THE NEXT PAC-MAN YOU CATCH WILL THEN BE CONSIDERED THE 1st PAC-MAN ON YOUR CLOWN’S HEAD BY THE GAME AND YOU WILL ONLY RECEIVE 200 PAC-MAN BONUS POINTS FOR HIM. |. FIRST RACK PLAY: Just after you push the 1 or 2 player button, the message displayed below is shown centered on the monitor screen:
Page 23

Then the game setting, your Clown, and the balloons appear on the monitor screen and play begins. The 1st rack contains only 16 balloons. They are mostly Yellow (siow falling) with a few Red (medium falling) ones mixed in. in this rack, the balloons are popped by the pinin the Clown’'s hat when you position him under one of the descending balloons. At the same time as it is popped, the balloon’s point value is added to your score. If you kick the balloon and then pop it, its point value plus its bonus point value will be added to your score when the balloon is popped. If ALL the balloons in the first rack were kicked and then popped, the game gives this message centered on the monitor screen.

These points are then added to your score and the next rack appears on the screen.

  • SECOND RACK PLAY: The 2nd rack begins with 24 balloons. They are mostly Yellow and Red with a few Blue (fast falling) ones mixed in. Also mixed in with the balioons are at least two PAC-MEN. There could be more depending on where the “DIFFICULTY LEVEL” option is set. Refer to Figure 8g. . CHALLENGING RACKS: The CHALLENGING RACKS occur between racks 2 and 3, 4 and 5, 6 and 7, 8 and Q, etc. Play begins with balloons and an occasional bomb being thrown out of the buildings to the right and left of the Clown. You have to make the Clown catch the balloons. But never NEVER catch a bomb or it will blow your Clown off his unicycle and you will lose all the bonus points for the balloons you caught up to that time. If your Clown misses a balloon and lets it touch the ground, he will also fail off his unicycle and you lose all the bonus points for the balloons he caught until he fell. However, youDO NOT lose a Clown when he falls of his unicycle in a CHALLENGING RACK as you would when he falls off it during normal play.

2-16 Your Clown MUST catch eight balloons to get ANY of the bonus points for the balloons caught in the CHALLENGING RACK. After the eighth balloon is caught, the Clown will pop all eight and their bonus point values will be added to your score.

. When you catch the last balloon of a rack, the game gives the message shown below.

In this way, the game tells you which player — NUMBER 1 or NUMBER 2 — is being advanced to the next rack and what the number of the bonus multiplier is for that next rack. The bonus multipliers range from 2 to 5. The only exception to this would be when the next RACK is a CHALLENGING RACK. When this is the case, you will see this message displayed centered on the monitor*screen:

The CHALLENGING RACKS are described above.

Page 24

After each CHALLENGING RACK is over, the game gives the message below displayed centered on the monitor screen:

Then your Clown and the next rack of balloons. appear on the monitor screen and play begins.

  • As you improve your skills and become better and better at the game, advancing into the more difficult racks, you will see only two PAC-MEN per rack, an ever increasing number of Blue balloons which will fall at an angle instead of straight down, and when you “KICK” a missed balloon, another sometimes begins its fall right away (you then have TWO balloons in the air at the SAME time). However, you can NEVER have MORE than two balloons in the air at the SAME time. When you miss a balloon and it hits the ground causing your Clown to fall off his unicycle, assuming you have at least one reserve unicycle left, your Clown and a new unicycle appear in the center of the monitor screen, the circus music starts to play, and play begins anew. When you miss a balloon and your Clown falls off his LAST unicycle, these words are displayed centered on the monitor screen as shown below.

tase oven ouayER 2 your SCORE pete Th es

2-17 If your score was high enough to become one of the ten best scores, the game will go into the High Score/Initial mode immediately after the above display. If your score is not high enough to cause the game to go into the High Score/Initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready- To-Play mode (if there are still credits left in its memory). In the High Score/initial mode the game gives a display which looks like that shown below.

By spinning the controller ball to the right, you can make the balloon move down the alphabet: “A”, “B", “C”, “D”, etc. By moving the controller ball to the left, you can make the balloon move up the alphabet: “Z”, “Y”, “X", “W", etc. When you reach your initial, stop the rotation of the controller ball and push the KICK button. Your initial is printed out below the on-screen instructions. If you do not wish to put your initials opposite your score, just press the KICK button three times. Three “A” 's will appear below the onscreen instructions. Or — you can push either the 1 or 2 PLAYER button to leave this mode immediately.

NOTE: If you make a mistake, you can erase the wrong letter by positioning the balloon opposite the “ERASE” word at the bottom of the line of alphabet characters and pressing the KICK button. Then simply go back and print out the correct letter.

When you’ve printed out your last initial. move the balloon opposite the “END” word and press the KICK button to tell the game you are through printing out your initials. The game will then give the following RANKINGS display showing your score opposite your ranking and your initials.

Page 25
NOTE: If you don’t tell the game you are through printing out your initials as instructed above, the game will automatically go into the RANKINGS display after a short wait.

After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To- Play mode (if there are still credits left in its memory).

  • Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

TWO PLAYER OPERATION The Upright, Mini, and Cocktail Table models all have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however.

  • In the Upright and Mini models, the players must take turns at the controls.
  • In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when it is your turn. (When it is not your turn, your set of controls will have NO effect on the game.)
  • Your turn lasts until your Clown falls off his unicycle. At this point, the game will do one of several things depending on whether or not the fallen Clown was riding yourlast unicycle or if you still have others remaining in reserve.

2-18 FALLEN CLOWN — UNICYCLES REMAINING IN RESERVE

  • The game stops and the other player's Clown and balloons appear on the screen. ¢ Next, “PLAYER — UP” is displayed at right middle of the monitor screen and game play begins for the other player. FALLEN CLOWN — NO UNICYCLES REMAINING IN RESERVE *¢ Game displays:

¢ After the above display, if your score was high enough, it goes to the “HIGH SCORE/INITIAL” mode. e After this mode, the other player's Clown, balloons, and “PLAYER UP” appear on the monitor screen. Play then begins for the other player. ¢ If your score was NOT high enough to cause the game to go into the “HIGH SCORE/INITIAL” mode, the game will just display the other player's Clown, balloons, and “PLAYER __ UP” on the monitor screen. Then play begins for the other player.

Page 26

Ill. Maintenance and Repair

Your KICK-MAN game needs certain types of maintenance to keep it in good working order. Clean, well maintained games attract players and earn more profits. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on orin the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any househoid cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was !ooking at the game through a fog. This fogging damage CAN NCT be repaired or reversed.! The ONLY solution is to replace the damaged piece of plastic. FUSE REPLACEMENT This game contains several fuses located as shown in Figure 11.

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Mech. Panel and the Power Supply Board.

3-1

  • MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Mech. Panel and the Power Supply Board.
  • COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Mech. Panel and the Power Supply Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual.

See the T.V. Monitor Manual (available on request from your distributor or monitor manufacturer) and/ or the T.V. Troubleshooting Section of this manual for further information.

FUSES LOCATED ON POWER SUPPLY AND MECH PANEL

Figure 11 Location of fuses

Page 27

OPENING THE CONTROL PANEL 1, UPRIGHT MODEL: SEE FIGURE 12. 2. MINI MODEL: SEE FIGURE 13. ¢ The control panel is held in place by two latches, © The control panel is held in place by two latches, one on the left side and one on the right side of one on the right side, and one on the left side of the cabinet. the cabinet. They are spring loaded to provide constant They are spring loaded to provide constant positive pressure on their latch plates. Positive pressure on their latch plates. They can be reached through the coin door They can be reached through the coin door AFTER turning power to the game off. AFTER turning power to the game off. To release the latches, lift up and toward the To release the latches, lift up and toward the front center of the control panel. center of the contro! panel. Once they are released, unhook them from their Once they are released, unhook them from their latch plates. latch plates. © To remove the control panel: © To remove the control panel: Raise it up and tilt it toward you until you can see Raise it up and tilt it toward you until youcan see the cable behind it. the cable behind it. Cradling the control panel between yourself Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. and the cabinet, disconnect it from its cabling. The control panel is now free and can be The control panel is now free and can be removed. removed. e To reinstall the control panel, reverse this ¢ To reinstall the contro! panel, reverse this procedure. procedure.

UPRIGHT a Figure 12 Removing control panel - Upright game Figure 13 Removing control panel — Mini game

Page 28
  • COCKTAIL TABLE MODEL: © Each control panel is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 14.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open as is indicated in Figure 14.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 15.

CLAMPS © To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. ¢ To reinstall the contro! panel, reverse this procedure.

REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY:

  • UPRIGHT MODEL:
NOTE: In order to do this, the control panel MUST be removed first. See the “Upright Model” procedure. © Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted up. Grasp the main-display-glass in the bottom center, lift up slightly and pull it toward you about an inch, let it down just far enough so you can get hold of its top edge with your other hand and lift it out of the game. See Figure 16. Remove the screws which secure the T.V. bezel assembly in place. The T.V. bezel assembly is now free and can be slid out of the cabinet. See Figure 17. To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure.

Figure 14 Opening Cocktail game

Page 29

REMOVE (2) SCREWS

  • SCREWS UNDER SHELF

Figure 15 Removing control panel — Cocktail game

DISPLAY GLASS

REMOVE SCREWS

Figure 16 Removing display glass — Upright game Figure 17 Removing bezel — Upright game

3-4

Page 30
  • MINI MODEL: @ Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.
NOTE: In order to do this, the control panel MUST be removed first. See above “Mini Model” procedure.
  • COCKTAIL TABLE MODEL: ¢ Turn the power off to the game and remove the control panel.
  • Remove the screws which secure the glass NOTE: This may be done with the table top in the clamping plate. See Figure 18. closed or the open position. If you decide to open © Lift out the glass clamping plate. This frees the the table top, TURN THE POWER TO THE GAME main-display-glass so it can be lifted up. OFF FIRST. By putting your finger in the hole in the middle of the main-display-giass support, you can lift it up and out. See Figure 18. ¢ Remove the screws which secure the table top Remove the screws which secure the T.V. bezel glass clamps in place. assembly and lift it out. See Figure 19. © Remove the table top glass. Fi : Lift out the T.V. bezel assembly.

Neply-oles cope eee * To reinstall the T.V. bezel assembly and the table

play-9 ~ top glass, simply reverse this procedure.

DISPLAY

REMOVE SCREWS CLAMPING PLATE

Figure 18 Removing display glass — Mini game Figure 19 Removing bezel — Mini game

3-5

Page 31

T.V. MONITOR REPLACEMENT:

CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.
  • UPRIGHT MODEL. SEE FIGURE 20. « Turn power off to the game. © Open the rear access door. © Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. © Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Upright Model” procedure. @ With the removal of only four bolts, the T.V. monitor and its mounting board will be loose.

REMOVE

  • BOLTS SLIDE (2 EACH SIDE), MONITOR BOARD lo OUT BACK

py

Figure 20 Removing monitor — Upright game @ The monitor mounting board slides on top of and against two metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. ¢ To reinstall the T.V. monitor, reverse this procedure. After replacing the T.V. monitor, be sure to run the game Self-Test.

  • MINI MODEL: SEE FIGURE 21. © Turn the power off to the game. Open the rear access door. © Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel must be removed. See above “Mini Model” procedure. ¢ With the removal of only four bolts, the T.V. monitor will be loose.
CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet.

¢ The monitor is removed by supporting it and pulling straight back. (BE CAREFUL not to hit monitor on its rear support bracket.)

  • To reinstall the T.V. monitor, reverse this procedure.
  • After replacing the T.V. monitor, be sure to run the game Self-Test.

Figure 21 Removing monitor — Mini game

Page 32

CLAMPS

Figure 22 Opening Cocktail game

  • COCKTAIL MODEL: © Turn the power off to the game.
  • Open the coin box door and release the two latches indicated in Figure 22.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!

Once the latches are released, unhook them from their latch plates. ¢ Grasp the table top at “A” and open it as indicated in Figure 22.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

¢ Remove the screws which hold the table top glass clamps in place. « Remove the table top glass. © Lift out the T.V. bezel assembly. © Completely disconnect the T.V. monitor from ail its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. ¢ Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 23.

  • Close the Cocktail Table and re-latch it. Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 23. Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both,

3-7 ¢ Lift the T.V. monitor straight up and out of the table top being very careful not to bump the neck of the picture tube.

  • To reinstall the T.V. monitor assembly reverse this procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. ¢ After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE (6) SCREWS (3 EACH SIDE) AND LIFT MONITOR STRAIGHT UP

REMOVE (4) SCREWS (2 EACH SIDEY

Figure 23 Removing monitor — Cocktail game

Page 33

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT:

  • UPRIGHT MODEL. SEE FIGURE 24. ¢ Turn the power to the game off. Unlock and open the rear access door. © Disconnect all cabling from the P.C. boards and lift them out of their card rack. ¢ Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 24, and slide the linear power supply board out the back of the cabinet. ® To reinstall the above P.C.B.’s, reverse this procedure.
NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.

POWER SUPPLY P.C.B.

REMOVE THIS SUPPORT TO SLIDE P.C.B. OUT

  • MINI MODEL. SEE FIGURE 24. © Turn the power off to the game. Unlock and open the rear access door. © Disconnect all cabling from the P.C. boards and lift them out of their card rack. Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 24, and slide the linear power supply board out the back of the cabinet.
  • To reinstall the above P.C.B.’s, reverse this procedure.
  • COCKTAIL TABLE MODEL. SEE FIGURE 24. ¢ Turn the power off to the game. ¢ Open the cabinet: Open the coin box door and release the two latches indicated in Figure 22.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

Once they're released, unhook them from their latch plates.

REMOVE THIS SUPPORT TO SLIDE P.C.B. OUT

REMOVE (2) SUPPORTS TO SLIDE P.C.B.

UPRIGHT

POWER SUPPLY P.C.B.

COCKTAIL

Figure 24 Replacing power supply P.C.B. — All versions

Page 34
  • Grasp the table top at “A” and open it as OPENING THE ATTRACTION PANEL: indicated in Figure 22.
  • UPRIGHT MODEL: © Turn the power to the game off. © Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See
CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

e Remove the linear power supply board. See Figure 24. Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the linear power supply can be lifted out the top of the cabinet. To reinstall the linear power supply board, reverse this procedure. To remove the P.C. boards from the card rack. See Figure 25. Disconnect them from ALL their cabling. The P.C. boards are now free and can be slid from their rack. To reinstall the P.C. boards, reverse this procedure.

  • SCREWS TO REMOVE FROM CABINET

REMOVE CABLING

Figure 25 Replacing card rack P.C.B.’s — All versions

3-9 Figure 26. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this procedure. © The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.
  • Replacing the fluorescent tube starter. See Figure 27. Be sure the power to the game has been turned off.

REMOVE (3) SCREWS (USE SPECIAL WRENCH EQUIPPED WITH YOUR GAME)

LIFT ATTRACTION PANEL STRAIGHT UP

Figure 26 Removing attraction panel — Upright game

Page 35

Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure.

Replacement of the fluorescent tube mounting bracket assembly. See Figure 28.

Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch it's power cable on anything.

¥, TURN TO REPLACE To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure. ® Replacing the speaker. See Figure 29. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from it's cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker.

FLUORESCENT TUBE STARTER

Figure 27 Replacing fluorescent starter — Upright game

REMOVE

  • SCREWS

Figure 28 Replacing fluorescent light mounting bracket — Upright game

3-10 REMOVE SPEAKERS THRU OPENING

Figure 29 Replacing speaker — Upright game

Page 36
  • MINI MODEL. SEE FIGURE 30. © Turn the power off to the game. Remove the screws from the top and bottom of the formed attraction panel. Remove the formed attraction panel by pulling it straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board. © To service the light bulbs and their mounting board: Turn the power to the game back on so you can see which bulbs are burnt out. Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. © To completely replace the light bulb mounting board:

Figure 30 Removing attraction panel — Mini game Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. To reinstall the above removed items, reverse this procedure. To replace the speaker. See Figure 31. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.

  • THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL.

Figure 31 Replacing speaker — Mini game

Page 37

COIN DOOR MAINTENANCE: METAL COIN ACCEPTOR MECHANISMS Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanism as shown in Figure 32. ¢ Push down on the two spring loaded latches. While holding the latches down, pull the top of the coin acceptor mechanism toward you. e Release the latches and lift out the coin acceptor mechanism.
  • Clean the magnet of all foreign particles. See Figure 33. ¢ This may be accomplished by swinging the gate open as shown in the above figure.
  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.)

ACCEPTOR OUT

Figure 32 Removing coin acceptor ¢ Also clean the pivot pin.

  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: Place the coin acceptor in boiling water for about ten minutes.
CAUTION: BE CAREFUL NOT TO BURN

® Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. Rinse the coin acceptor in clean boiling water. Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 33 Opening the metal coin acceptor

Page 38
  • To lubricate the coin acceptor: Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 34. ¢ Be extremely careful to keep the powered graphite away from paths that are traveled by the coins.
WARNING DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 35. Place the two pegs at the coin acceptor’s base into their retaining slots. Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches. 410. Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

UNDERSIZE LEVER

CRADLE

Figure 34 Lubricating the metal coin acceptor PLASTIC COIN ACCEPTOR MECHANISMS The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanism(s) as shown in Figure 32. e Push down on the two spring loaded latches. ¢ While holding the latches down, pull the top of the acceptor mechanism toward you. ¢ Release the latches and lift out the mechanism.
  • Squeeze the two pins indicated in Figure 36 together to open the mechanism and break it down into its three basic parts. Clean the mechanism in hot soapy water. !t never rusts. e Rinse the mechanism in clean hot water and allow it to dry. Reassemble the mechanism (it never needs lubrication).

PUSH ACCEPTOR IN

PLACE PINS IN GROOVES

Figure 35 Reinstalling coin acceptor

Page 39

SQUEEZE PINS TOGETHER BP SWING BOTH GATES OPEN TO UNLOCK

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 36 Opening the plastic coin acceptor

  • Check the coin chute for obstructions such as: the coin door until it snaps in place and is held paper, gum, etc. there by the two spring loaded latches.
  • Reinstall the coin acceptor to the coin door. See 7. Close and lock coin door. Figure 35.
NOTE: See Figure 37 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters. e Place the two pegs at the coin acceptor’s base into their retaining slots. « Now push the top of the coin acceptor toward

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY .OR BOTH U.S. AND CANADIAN QUARTERS.

MAGNET

eS SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO. ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Page 40
Scan of page 40

This page is a drawing, shown as the original scan.

Page 41

KICK-MAN — ALL VERSIONS — BALL CONTROL ASSEMBLY

KICK-MAN — ALL VERSIONS — BALL CONTROL ASSEMBLY — PARTS LIST ORDER BY PART NUMBER ONLY | irew | PART NO. DESCRIPTION 0017-00101-0120 #10-24 x 1/2 FLAT HD. M.S. ( 8 REQ’D.) 0515-00100-0000 TOP PLATE 0515-00703-0000 SIDE POST ( 2 REQ’D.) 0515-00702-0000 POST 0017-00006-0080 ROLLER BEARING (2 REQ’D.) 0515-00705-0000 SPACER (2 REQ'D.) A515-00013-0000 BALL & SHAFT ASSY. 0017-00100-0114 1/4" RETAINING RING 0515-00701-0000 SHORT POST 0017-00101-0593 #8-32 x 1/4 SLT. PAN HD. EXT. M.S. 0515-00101-0000 BEARING RETAINER 0017-00101-0302 #6-32 x 3/16 SET SCREW (2 REQ’D.) A643-00010-0000 BUSH & DISC. ASSY. 0515-00103-0000 BOTTOM PLATE 0017-00101-0119 #10-24 x 1/2 BUT. HEX HD. MS. (3 REQ'D.) 0515-00102-0000 P.C. MTG. PLATE 0017-00101-0599 #8-32 x 5/16 SLT. HEX HD. SCR. W/SEMS (2 REQ'D.) 0017-00101-0099 #6 x 1/4 SLT. HEX HD. SCR. (4 REQ'D.) 0017-00007-0143 1/4 SPACER ( 4 REQ'D.) A082-91391-C000 BINARY ANGLE DECODER P.C. ASSY. O©OVMAHMARONM=A

Page 42

NO. 968 — KICK-MAN UPRIGHT — FRONT

Page 43

NO. 968 — KICK-MAN UPRIGHT — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0968-00904-00XF UPPER DISPLAY PLEX! — 22-13/16" x 5-31/32” x 3/16" 0537-00903-0044 GLASS CHANNEL — 5” LG. (2 REQ’D.) 0968-00102-00XF GLASS RETAINER BRKT. — UPPER 0968-00106-00XF GLASS RETAINER BRKT. — BOTTOM 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT BLK. SCR. (6 REQ’D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A595-00011-0000 HEADER LIGHT ASSY. 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS (2 REQ'D.) 0017-00003-0430 6” x 9” SPEAKER 4 OHM, 10W. (2 REQ'D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0968-00901 -0000 MIRROR — 22-13/16" x 24-1/8" x 3/16” 0968-00908-0200 SIDE SCENERY CARD — LEFT 0968-00908-0100 SIDE SCENERY CARD — RIGHT (NOT SEEN) 0968-00900-00XF MAIN VIEWING GLASS — 22-13/16" x 21-5/16" x 3/16” 0537-00903-0049 GLASS CHANNEL — 17-3/4" LG. (2 REQ’D.) 0629-00902-0800 GLASS LIFT CHANNEL — 20” LG. 0968-00122-00XF CONTROL PLATE 0017-00101 -0620 #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ'D.) 0961-00115-00XF STRIKE (2 REQ'D.) 0017-00009-0033 LATCH CLAMP (2 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT HEX HD. M.S. (8 REQ’D.) 0555-00901 -0000 PLASTIC LOCATING PIN (8 REQ’D.) 0550-00101-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0550-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) 0017-00032-0051 RED BUTTON SWITCH W/HARDWARE (2 REQ'D.) 0017-00032-0100 ILLUMINATED P.B. SWITCH — AMBER (2 REQ’D.) A515-00014-0000 CONTROL ASSY. A090-00300-08BK U.S.A. 25¢ COIN DOOR ASSY. A968-00017-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0200 KICK PLATE — 22-7/8” LG. 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ'D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ'D.)

Page 44

MAN UPRIGHT — REAR ACCESS NO. 968 — KICK:

4-4

Page 45

NO. 968 — KICK-MAN UPRIGHT — REAR ACCESS — PARTS LIST ORDER BY PART NUMBER ONLY | rem | PART NO. DESCRIPTION A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY. 0894-00913-0000 RECESSED HAND LIFT (2 REQ’D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCR. (12 REQ’D.) 0968-00906-0000 MONITOR MASK 0968-00901-0000 MIRROR — 22-13/16" x 24-1/8" x 3/16” 0968-00503-0000 MIRROR LOCKING CLEAT (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. MLS. (4 REQ'D.) A088-00015-0000 INTERLOCK SWITCH & BRKT. ASSY. 0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR (OR) 0017-00003-0401 WELLS-GARDNER — 19” COLOR DUAL SYNC HORIZ. MTG. MONITOR A968-00006-0000 MONITOR SUPPOPT RAIL ASSY. (2 REQ’D.) 0017-00102-0012 1/4-20 x 1-1/4 UNSLOT. HEX FLAT HD. BOLT (8 REQ’D.) 0017-00104-0014 7/8 DISH WASHER (8 REQ'D.) 0017-00103-0018 1/4-20 HEX NUT (8 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ'D.) 0017-00104-0046 7/8" FLAT WASHER (8 REQ'D.) 0968-00909-0000 LARGE MONITOR SHIELD — FISH PAPER A082-90910-D000 DUAL POWER AMP P.C. ASSY. — MCR2 A968-00019-0000 CARD RACK W/P.C. BOARDS ASSY. A082-90412-B000 125 VA. POWER SUPPLY P.C. ASSY. 0624-00902-0100 P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2" LG. (2 REQ’D.) 0017-00042-0255 #8 x 11/16 UNSLOT. HEX HD. MS. (10 REQ'’D.) 0017-00104-0037 #8 FLAT WASHER (10 REQ'D.) A945-00002-0000 125 VA FILTER ASSY. A968-00024-0000 TRANSFORMER BOARD ASSY. A508-00023-0000 LINE CORD CABLE ASSY. A961-00007-0000 CASTER ASSY. (2 REQ’D.) 0961-00109-0000 WHEEL BRKT. (2 REQ'D.) 00017-00042-0255 PLASTIC WHEEL (2 REQ'D.) 0894-00702-00XF SHAFT (2 REQ'’D.) 0017-00100-0037 3/8 E-RING (2 REQ’D.)

ADDITIONAL PARTS LIST A515-00021-0000 MULTIFUNCTION SWITCH & BRKT. ASSY. A097-00008-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8 SQR. BACK DOOR VENT GRILLE A950-00006-0000 COIN BOX CRADLE ASSY. 0950-00105-0000 COIN BOX COVER 0950-00104-0000 COIN BOX HANDLE 0950-00101-0000 COIN DEFLECTOR (2 REQ’D.) 0950-00900-0000 LARGE PLASTIC CASH BOX 0017-00101-0142 1/4-22 x 1-3/8 RND. HD. BOLT BLK. (4 REQ’D.) 0017-00104-0014 7/8 DISH WASHER (4 REQ’D.) 0017-00103-0018 1/4-20 HEX NUT (4 REQ'D.) A968-00027-0000 MASTER CABLE ASSY. A968-00025-0000 HIGH VOLTAGE CABLE ASSY. A968-00026-0000 LOW VOLTAGE CABLE ASSY. A968-00028-0000 CONTROL SHELF CABLE ASSY. A968-00029-0000 VIDEO SIGNAL CABLE ASSY. A866-00049-0000 LINE CORD ASSY. 0968-00126-0000 MONITOR BOARD BRKT. (2 REQ'’D.) 0017-00101-0769 #10 x 3/4 SLT. HEX HD. SCR. (8 REQ’D.)

Page 46

NO. 513 — KICK-MAN MINI — FRONT

Page 47

NO. 513 — KICK-MAN MINI — FRONT — PARTS LIST ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0513-00901-00XF DISPLAY PANEL 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (8 REQ’D.) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) A926-00010-0000 INSERT DISPLAY ASSY. 0017-00031-0030 WEDGE BASE LIGHT SOCKET (5 REQ’D.) 0017-00003-0219 #194 LAMP 14V., .27A. (5 REQ'D.) 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS (2 REQ’D.) 0017-00003-0430 6" x 9" SPEAKER 4 OHM, 10W. (2 REQ’D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ'D.) 0513-00902-00XF FRONT GLASS — 17-13/16" x 14-13/16" x 3/16” 0537-00903-0056 GLASS CHANNEL — 14-1/2" LG. (2 REQ’D.) A555-00016-0000 GLASS CLAMPING PLATE ASSY. 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (8 REQ'D.) 0513-00100-00XF CONTROL PLATE 0017-00101-0620 #8-32 x 1/2 CARRIAGE BOLT (8 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ'D.) 0555-00101-0100 CONTROL SHELF MTG. BRKT. —- RIGHT 0555-00101-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 PLASTIC LOCATING PIN (6 REQ’D.) 0017-00009-0033 LATCH CLAMP (2 REQ’D.) 0961-00115-00XF STRIKE (2 REQ'D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (16 REQ’D.) 0017-00032-0051 RED SWITCH BUTTON (2 REQ'D.) 0017-00032-0100 ILLUMINATED P.B. SWITCH — AMBER (2 REQ'D.) A515-00014-0000 CONTROL ASSEMBLY A090-00300-08BK U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0400 KICK PLATE — 17-15/16" LG. 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

Page 48

NO. 513 — KICK-MAN MINI — REAR ACCESS

4-8

Page 49

NO. 513 — KICK-MAN MINI — REAR ACCESS — PARTS LIST ORDER BY PART NUMBER ONLY

0017-00003-0430 6" x 9” SPEAKER 4 OHM, 10W. (2 REQ’D.) 0513-00900-0000 TV. BEZEL A961-00026-0000 BEZEL MTG. BRKT. ASSY. (2 REQ’D.) 0017-00003-0340 13” DUAL SYNC COLOR MONITOR — ELECTRO HOME (OR) 0017-00003-0396 13" DUAL SYNC COLOR MONITOR — WELLS-GARDNER A926-00012-00XF T.V. MTG. BRKT. ASSY. MONITOR MTG. BRKT. 0513-00101-0000 0017-00101-0628 0017-00104-0026 0017-00103-0061 A088-00015-0000 A090-00300-08BK A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0000 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) #8 FLAT WASHER (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) INTERLOCK SW. & BRKT. ASSY. U.S.A, 25¢ COIN DOOR ASSY. COIN BOX CRADLE ASSY. COIN BOX COVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ'D.) LARGE PLASTIC CASH BOX 1/4-22 x 1-3/8 RND. HD. BOLT (4 REQ’D.) 7/8 DISH WASHER (4 REQ'D.) 1/4-20 HEX NUT (4 REQ’D.) A082-90910-D000 A513-00016-0000 A513-00009-0000 DUAL POWER AMP P.C. ASSY. — MCR2 MECH. CARD RACK W/P.C. BRD'S. ASSY. TRANSFORMER BOARD ASSY. — NOT SEEN (LOCATED ON CABINET BASE) 125 VA. POWER SUPPLY P.C. ASSY. P.C. SUPPORT BRKT. — 12” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 2-1/2" LG. P.C. SUPPORT BRKT. — 6-1/2” LG. (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (12 REQ’D.) A082-90412-B000 0624-00902-0100 0624-00902-0300 0624-00902-0500 0017-00101-0141 0017-00104-0037 A945-00002-0000 A088-00013-0000 #8 FLAT WASHER (12 REQ'D.) 125 VA. FILTER ASSY. ON-OFF SWITCH & BRKT. ASSY. 0017-00009-0490 5-5/8" SQ. VENT GRILL (2 REQ’D.)

ADDITIONAL PARTS LIST MULTIFUNCTION SW. & BRKT. ASSY. BACK DOOR LOCK ASSY. PLASTIC PROTECTIVE BUBBLE — BACK DOOR #8-32 x 3/4 CARRIAGE BOLT (10 REQ’D.) #8-32 HEX NUT W/SEMS (10 REQ'D.) A515-00021-0000 A097-00008-0000 0926-00904-0000 0017-00101-0628 0017-00103-0061 3000-17246-1000 A513-00007-0000 A513-00012-0000 A968 -00029-0000 A513-00010-0000 A513-00011-0000 A866-00049-0000 GROUND STRAP CONTROL SHELF CABLE ASSY. MASTER CABLE ASSY. VIDEO SIGNAL CABLE ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. LINE CORD ASSY.

Page 50

NO. 515 — KICK-MAN COCKTAIL — FRONT

Page 51

NO. 515 — KICK-MAN COCKTAIL — FRONT — PARTS LIST ORDER BY PART NUMBER ONLY | rem | PART NO. DESCRIPTION 0017-00009-0499 COVER GLASS — 32” x 22” x 1/4" 0515-00901-0000 ARTWORK UNDERLAY 0775-00104-00XF GLASS CLIP (8 REQ’D.) 0017-00101-0117 #8 x 5/8 PHIL. TRS. HD. SCR. (16 REQ'D.) 0557-00900-0000 TV. BEZEL 0508-00905-0000 SMOKED PLEXI — 17-3/8" x 13-1/4” x 1/8" 0508-00901-0000 PLEXI-GLASS CLIPS (4 REQ’D.) 0017-00101-0017 #6 x 1/2 SLT. HEX HD. BLK. SCR. (4 REQ'’D.) A515-00006-0000 CONTROL SHELF ASSY. — PLAYER #1 A515-00006-0100 CONTROL SHELF ASSY. — PLAYER #2 0017-00009-0482 SPEAKER GRILLE — SMALL 0017-00003-0431 4” SQR. SPEAKER — 4 OHM, 10W. 0017-00009-0393 BLACK SPEAKER GRILLE W/SLOTS (3 REQ'D.) 0017-00003-0430 6” x 9" SPEAKER — 4 OHM, 10W. 0017-00101-0136 #8-32 x 1-1/4 CARRIAGE BOLT (16 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (16 REQ’D.) A090-00300-06BK U.S.A. 25¢ COIN DOOR ASSY. 0090-00002-02BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0017-00102-0048 3/8-16 x 2" LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

Page 52

NO. 515 — KICK-MAN COCKTAIL — REAR ACCESS

; SS

vo Rees >> py

4-12

Page 53

NO. 515 — KICK-MAN COCKTAIL — REAR ACCESS — PARTS LIST ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0017-00003-0339 ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR A515-00019-0000 MONITOR SUPPORT ASSY. — LEFT A515-00019-0100 MONITOR SUPPORT ASSY. — RIGHT 0017-00101-0109 #8 x 5/16 UNSLOT. HEX HD. BOLT (6 REQ’D.) 0927-00101-00XF SUPPORT ANGLE (2 REQ’D.) 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. MS. (4 REQ’D.) 0017-00009-0514 2-1/2" HINGE (2 REQ’D.) 0017-00101-0639 #8-32 x 1-1/4 CARRIAGE BOLT (4 REQ’D.) 0017-00101 -0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0515-00106-00XF CONTROL PLATE — PLYR. #1 0515-00106-01XF CONTROL PLATE — PLYR. #2 0017-00101-0620 #8-32 x 1/2 CARRIAGE BOLT (8 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ’D.) 0017-00101-0341 #6 x 1/4 PHIL. TRS. HD. SCR. (6 REQ’D.) 0510-00101-00XF BOTTOM PAN (2 REQ'D.) A515-00014-0000 CONTROL ASSY. (2 REQ’D.) 0017-00032-0051 SMALL RED BUTTON SWITCH W/HARDWARE (2 REQ’D.) 0017-00042-0257 YELLOW PUSH BUTTON ASSY. (2 REQ’D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (2 REQ'D.) 0017-00103-0054 5/8-11 PAL NUT (2 REQ’D.) 0930-00104-0000 PANEL LOCATING BRKT. (4 REQ'D.) 0017-00101-0025 #8 x 1/2 SLT. HEX HD. M.S. (16 REQ’D.) 0930-00904-0000 LIGHT SHIELD (2 REQ’D.) 0017-00031-0044 WEDGE BASE LAMP SOCKET (4 REQ'D.) 0017-00003-0219 #194 LAMP 14V., .27A. (4 REQ’D.) 0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ'D.) 0017-00003-0431 4" SQR. SPEAKER 4 OHM, 10W. 0017-00003-0430 6” x 9" SPEAKER 4 OHM, 10W. A082-90412-B000 125 VA. POWER SUPPLY 0624-00902-0100 P.C. SUPPORT BRKT. — 12” LG. 0624-00902-0500 P.C. SUPPORT BRKT. — 6-1/2” LG. (3 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (10 REQ’D.) 0017-00104-0031 #8 FLAT WASHER (10 REQ’D.) A513-00016-0000 MECH. CARD RACK W/BOARDS ASSY. A515-00009-0000 TRANSFORMER BOARD ASSY. A945-00002-0000 125 VA. FILTER ASSY. A775-00013-0000 FAN ASSEMBLY 0151-00081-0000 4" FAN 0775-00110-00XF FAN PLATE 0749-00106-00XF VENT SCREEN 0017-00101-0347 #6-32 x 1/2 R.H.M.S. (4 REQ'D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00103-0005 #6-32 HEX NUT (4 REQ’D.) 0017-00101-0026 #8 x 5/8 SLT. HEX HD. M.S. (4 REQ'D.)

Page 54

NO. 515 — KICK-MAN COCKTAIL — REAR ACCESS — PARTS LIST (cont'd)

A082-90910-D000 A088-00014-0000 A515-00021-0000 A927-00008-0000 0610-00132-00ZN 0017-00009-0033 0017-00101-0141 A927-00019-0000 A962-00004-0000 A962-00005-0000 0962-00101-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 0927-00907-0000 A515-00012-0000 A515-0001 1-0000 A515-00010-0000 A515-00007-0000 A515-00007-0100 A515-00022-0000 A968-00017-0000 A927-00005-0000

A866-00049-0000 ORDER BY PART NUMBER ONLY

ADDITIONAL PARTS LIST DUAL POWER AMP P.C. ASSY. — MCR 2 INTERLOCK SWITCH & BRKT. ASSY. MULTIFUNCTION SWITCH BRKT. ASSY. ON/OFF SWITCH ASSY. STRIKE (2 REQ’D.) LATCH CLAMP (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) COIN BOX ASSY. COIN BOX COVER ASSY. COIN BOX SIDE CHANNEL ASSY. — SHORT COIN BOX SIDE CHANNEL — SHORT #8-32 x 3/4 CARRIAGE BOLT (4 REQ'’D.) #8 WASHER (4 REQ'D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) HIGH VOLTAGE SHIELD MASTER CABLE ASSY. HIGH VOLTAGE CABLE ASSY. LOW VOLTAGE CABLE ASSY. CONTROL SHELF CABLE ASSY. — PLYR. #1 CONTROL SHELF CABLE ASSY. — PLYR. #2 VIDEO SIGNAL CABLE ASSY. COIN DOOR CABLE ASSY. LEG KIT ASSY. (HIGH BASE) — OPTIONAL (INCLUDES 4 LEGS & HARDWARE) LINE CORD ASSY.

Page 55

KICK-MAN — ALL VERSIONS — NOT SHOWN — PARTS LIST ORDER BY PART NUMBER ONLY [rem | PART NO. DESCRIPTION TRANSFORMER BOARD ASSEMBLY MTO00-00089-A000 POWER TRANSFORMER — 115V., 60 HZ (UPRIGHT & MINI) MT00-00092-0000 TRANSFORMER (UPRIGHT & MINI) MTO00-00093-0000 TRANSFORMER W/MAGNETIC SHIELD (GOCKTAIL ONLY) MTO00-00096-0000 POWER TRANSFORMER — 100/125V., 60 HZ (COCKTAIL ONLY) 0017-00101-0628 #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) 0017-00104-0026 #8 1/2" FLAT WASHER (4 REQ’D.) 0017-00103-0008 #8-32 HEX NUT (4 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. M.S. (22 REQ'D.) 0720-00001-0400 4 POSITION FUSE CLIP ASSY. (UPRIGHT & COCKTAIL) 0720-00001-0300 3 POSITION FUSE CLIP ASSY. (MINI ONLY) 0017-00003-0004 SLO-BLO FUSE — 2A., 250V. (2 REQ’D.) 0017-00003-0217 SLO-BLO FUSE — 2-1/2A., 125V. 0017-00003-0002 SLO-BLO FUSE — 1/2A., 250V. (UPRIGHT & COCKTAIL) A945-00005-0000 CAPACITOR ASSY. — 60HZ 0017-00003-0379 CAPACITOR CLAMP A508-00037-0000 NOISE FILTER ASSY. —- 2 LEAD 3010-13106-0000 TERMINAL STRIP 0017-00021-0370 MALE CONNECTOR — 5 TAB 3000-17246-0200 .350 WIDE GROUND STRAP (COCKTAIL ONLY) 3000-17246-0300 -350 WIDE GROUND STRAP (COCKTAIL & MINI) 3000-17246-0500 §.50 x .350 WIDE GROUND STRAP (MINI & UPRIGHT) 3000-17246-0900 48.00 x .350 WIDE GROUND STRAP (UPRIGHT ONLY) 3010-03003-0000 GROUNDING CLIP

CARD RACK W/BOARDS ASSY. A084-90908-A968 SOUND BOARD ASSY. A084-90009-A968 C.P.U. BOARD ASSY. (UPRIGHT) A084-90009-A513 C.P.U. BOARD ASSY. (MINI & COCKTAIL) A084-91399-A968 VIDEO GENERATOR BOARD ASSY. (UPRIGHT) A084-91399-A513 VIDEO GENERATOR BOARD ASSY. (MINI & COCKTAIL) 0017-00042-0208 P.C. BOARD SPACER SUPPORT — 1-1/8" LG. (4 REQ'D.) 0017-00042-0287 P.C. BOARD SPACER SUPPORT — 5/8” LG. (4 REQ’D.) 0017-00101-0085 #6 x 5/16 SLT. HEX HD. M.S. (8 REQ’D.) 0968-0051 1-0000 BASE CARD RACK SUPPORT — BLOCK 0017-00101-0033 #8 x 1-1/4 SLT. HEX HD. MS. (2 REQ'D.) 0017-00104-0031 #8 WASHER (2 REQ’D.) 0968-00510-0000 TOP CARD RACK SUPPORT — BLOCK 0968-00125-0000 SUPPORT BRKT. TO CABINET SIDE 0017-00101-0014 #6 x 1/2 SLT. HEX HD. SCREW (2 REQ'D.)

4-15

Page 56

NO. 968 — KICK-MAN UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY.

4-16

Page 57

NO. 968 — KICK-MAN UPRIGHT — HEADER FLUORESCENT FIXTURE ASSY. — PARTS LIST ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0595-00105-0000 FLUORESCENT BRKT. 0017-00003-0043 18” COOL WHITE FLUOR. LAMP. 0017-00021-0005 FLUORESCENT LOCKS (2 REQ'D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ’D.) 0017-00003-0412 FLUOR. STARTER HOLDER W/WIRE LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ'D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ’D.) 0017-00003-0019 FLUOR. STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) A508-00017-0000 FLUORESCENT CABLE ASSY. A961-00042-0000 LINE FILTER ASSY. — NOT SHOWN

Page 58

FILTER ASSY.

Page 59

FILTER ASSY. — PARTS LIST ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0945-00101-OO0XF CHASSIS. 0945-00803-0100 CAPACITOR — 55000MF — 25V. 0945-00803-0200 CAPACITOR — 100000MF — 15V. 0945-00100-0000 CAPACITOR STRAP 0017-00101-0555 #6-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) 0017-00021-0539 5 POSITION TERMINAL STRIP (2 REQ’D) 0017-00101-0510 #4-40 x 1/2 SLT. PAN HD. SCR. (4 REQ’D.) 0017-00104-0087 #4 FLAT WASHER (4 REQ'D.) 0017-00104-0071 #4 EXT. TOOTH WASHER (4 REQ’D.) 0017-00103-0002 #4-40 HEX NUT (4 REQ’D.) 0062-122H7-1XXX RESISTOR — 150 OHM, 2W. 0062-086H7-1XXX RESISTOR — 47 OHM, 2W. — LOCATED ON OPPOSITE TERMINAL STRIP 0017-00003-0008 FUSE — 6AMP — 120V. 0017-00003-0174 FUSE — 10 AMP — 32V. 0017-00003-0433 FUSE HOLDER (2 REQ’D.) 0017-0004 1-0008 RUBBER GROMMET A089-00007-0000 FILTER CABLE ASSY. #2 A089-00006-0000 FILTER CABLE ASSV. #1 0945-00804-0100 DIODE — 12A. — SOV. (4 REQ'’D.) 0017-00103-0086 #10-32 HEX NUT (4 REQ’D.) 0017-00021-0484 SOLDER LUG (4 REQ'’D.) 0017-00104-0107 #10 FLAT WASHER (4 REQ’D.) 0017-00009-0510 INSULATOR (8 REQ'’D.) 0017-00042-0283 BUSHING (4 REQ’D.) 0945-00900-0000 DIODE FORMED FISHPAPER COVER — NOT SHOWN

4-19

Page 60

FRONT DOOR ASSEMBLY — U.S.A. 25¢

Page 61

FRONT DOOR ASSEMBLY — U.S.A. 25¢ — PARTS LIST ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0090-00002-02BK DOUBLE ENTRY COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) A090-00073-02BK DOUBLE ENTRY COIN DOOR W/DRESS PLATE 0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCREW (4 REQ'D.) 0017-00007-0019 KEY HOOK 0017-00101-0552 #6-32 x 1/4 CARRIAGE BOLT (4 REQ’D.) 0090-00117-O03XF COIN ENTRY PLATE — 25¢ (2 REQ’D.) A097-00005-0000 DOOR LOCK & KEY W/SCREW & NUT (OR) A097-00006-0000 DOOR LOCK & KEY W/SGREW & NUT 0090-00128-00XF DOOR TILT SWITCH BRKT. 0017-00005-0041 DOOR CAM A090-00071-0000 DOOR TILT SWITCH 0090-00126-01XF SWITCH BACK-UP PLATE 0017-00101-0528 #5-40 x 3/4” PHIL. HD. M.S. (2 REQ’D.) A090-00004-0000 DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 0090-00903-9500 25¢ WINDOW (2 REQ'D.) 0090-00143-00XF COIN PLEX RETAINER 0017-00003-0219 12 VOLT LAMP — G.E. #1895 (2 REQ’D.) 0017-00031--0048 BAYONET SOCKET W/BRKT. (2 REQ'’D.) 0017-00104-0002 #6 SPLIT LOCK WASHER (8 REQ’D.) 0017-00103-0087 #6-32 HEX NUT (8 REQ’D.) A090-00057-0000 COIN METER 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. SCR. (8 REQ'D.) 0017-00032-0051 PUSH BUTTON SWITCH 0017-00032-0007 SLIDE SWITCH 0017-00072-0034 STEEL OVAL HD. RIVET 0090-00173-0000 COIN COUNTER MTG. BRKT. A090-00082-0000 TEST SWITCH & BRKT. ASSY. (ITEMS 23 THRU 25) A090-00087-0000 COIN CHUTE & TOP ASSYV. (2 REQ’D.) 0010-00134-0000 SPRING 0010-00181-0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN 0090-001 29-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0093-00155-00XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 REJECT LEVER ASSY. (2 REQ'D.) (ITEMS 30 THRU 33) A090-00085-0000 COIN ACCEPTOR FRAME ASSV. (2 REQ’D.) 0017-00005-0003 COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) (OR) 0017-00005-0211 COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ'D.) (OR) 90017-00005-0214 COIN ACCEPTOR W/STRING CUTTER (2 REQ’D.) A090-00064-0000 ANTI-PENNY DEVICE 0017-00101-0099 #6 x 1/4 SLT. HEX HD. M.S. (2 REQ'D.) 0090-00162-00XF COIN SWITCH MTG. BRKT. 0017-00005-0203 COIN SWITCH CHUTE 0017-00005-0195 COIN SWITCH 0010-00599-0000 COIN SWITCH WIRE 0017-00007-0132 PUSH-ON RING A090-00059-0400 COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) 0017-00101-0698 #4-40 x 3/4 SLT. RND. HD. M.S. (2 REQ’D.) A090-00077-0000 COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43) OCHWOMNONDAON +

4-21

Page 62

V Technical Troubleshooting

Page 63

Harness Component Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features maifunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Typical problems falling in this category are coin and credit problems, power problems and failure of individuai features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of testcoins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does hot cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. lf necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 64

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same iine. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. lf you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in , areas almost impossible to find. First, try inserting a

5-2 new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine ail the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. lf a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 65

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system’s “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions.

RAM — random-access memory. Stores binary bits

as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LS! “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI! microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:

  • -The Z-80 is fully software compatible with the popular 8080A CPU.
  • Existing designs can be easily converted to include the Z-80. The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic. 3.
Page 66

General Purpose Registers There are two matched sets of generai purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These genera! purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)

Subtract Increment

Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit

Compare Test bit

Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

2-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described,

= 27 M, =

wRea «| SYSTEM tora = 22_| CONTROLS 55 21 wa we |

RFSH «|

HALT <———_j

cpu WAIT) =———> CONTROL

cpu BUS CONTROL

"1 +5V GND Z-80 CPU

Z-80 PIN CONFIGURATION 38 ADDRESS 39 BUS

ie DATA jem dg BUS

Page 67

AoAys (Address Bus) Tri-state output, active high. Ag-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allowthe user to directly select up to 256 input or 256 output ports. Ay is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.

Dy-D; (Data Bus) Tri-state input/output, active high. D)-D, constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

M, (Machine Cycle one) Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle.

MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The |[ORQ signal indicates that the lower half of the address bus holds a valid 1/O address for al/O read or write operation. An 1ORQ signai is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) _ Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.

5-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.

INT (Interrupt Request) Input, active low. The Interrupt Request signa! is generated by !/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable

interrupt request line has a higher priority than INT

and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WATT cycles can prevent_the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 68
  • Set Register | = 00H
  • Set Register R =00H
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals. Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.

5-6

Page 69

KICK-MAN MCR tl SYSTEM P.C. BOARD JUMPER OPTIONS

VIDEO GENERATOR P.C. BOARD

JUMPER OP- TION FOR PROGRAM ROMs ONLY.

MANUFACTURER |EPROM Ni

NUMEROUS MFR'S 2532

NUMEROUS MFR’S 2732

*= CUT JUMPER WIRES WHERE THIS SYMBOL “*" APPEARS. The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the C.P.U. P.C. Board used in the MCR II System has 6 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires. All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut. The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wires number. If there is NO “*” under a jumper wires number, THAT PARTICULAR JUMPER WIRE IS NOT TO BE CUT.

Page 70

KICK-MAN — ALL MODELS SOUND I/O BOARD EPROMS VERSION NO. 1

CIC

0968-008030968-008030968-008030968-00803
3800-A3900-B4000-C4100-D
KICK—S-1/OKICK—S-I/OKICK—S-i/OKICK—S-I/O.

WHITE WHITE WHITE WHITE

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this PC. BOARD to FUNCTION PROPERLY!!

5-8

Page 71

KICK-MAN — ALL MODELS SOUND I/O BOARD EPROMS VERSION NO. 2

re rr re rears) | cary

aie

ise] ? +See] [cea ree Aca + | Ses

Lesa +o +

A 1 LJ

sje] least tors Fry 2

es) zm |*!

sie

aos Fe 88") cary reo! mace WHICs

0968-008030968-008030968-00803
4200-A4300-B4500-D
KICK—S-V/O.KICK—S-1/0KICK—S-I/OKICK—S-I/O.
GRAYGRAYGRAYGRAY

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C. BOARD to FUNCTION PROPERLY!

5-9

Page 72

0513-00803 0400-A KICK—M&C-CPU ORANGE

0513-00803 0500-B. KICK—M&C-CPU ORANGE

0513-00803 0600-C KICK—M&C-CPU ORANGE

0513-00803 0700-D KICK—M&C-CPU ORANGE

0513-00803 0800-E KICK—M&C-CPU ORANGE

0513-00803 0900-F KICK—M&C-CPU ORANGE KICK-MAN MINI AND COCKTAIL CPU EPROMS VERSION NO. 1

wa =— fi] & i

e |=

3 (ean) [7] [ieee Fa) am 388% Ts ron)” oaihanr ‘en A eer

eral

fae]

ee za oa Sate Ei me sore $0) voi Fore. et 0513-00803 1000-G. KICK—M&C-CPU ORANGE

0513-00803 1100-H KICK—M&C-CPU ORANGE

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C. BOARD to FUNCTION PROPERLY!

5-10

Page 73

KICK-MAN MINI AND COCKTAIL CPU EPROMS VERSION NO. 2

0513-00803 1200-A. KICK—M&C-CPU PURPLE

0513-00803 Ea 0513-00803 1300-8 = 1000-G KICK—M&C-CPU Pom KICK—M&C-CPU PURPLE ORANGE

0513-00803 1100-H. KICK—M&C-CPU ORANGE 0513-00803 1400-C KICK—M&C-CPU PURPLE

0513-00803 1500-D KICK—M&C-CPU PURPLE

0513-00803 1600-E KICK—M&C-CPU PURPLE

0513-00803 1700-F KICK—M&C-CPU PURPLE

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C. BOARD to FUNCTION PROPERLY!

5-11

Page 74

KICK-MAN UPRIGHT CPU EPROMS VERSION NO. 1

0968-00803 0600-A KICK--UR-CPU BLUE cca =

0968-00803 1800-G KICK—UR-CPU BLUE 0968-00803 0700-B KICK—UR-CPU BLUE

DP irae fess

0968-00803 1900-H KICK—UR-CPU BLUE 0968-00803 0800-C KICK—UR-CPU BLUE

0968-00803 0800-D KICK—UR-CPU BLUE

0968-00803 1000-E KICK-—UR-CPU BLUE

0968-00803 1100-F KICK—UR-CPU BLUE

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C. BOARD to FUNCTION PROPERLY!

Page 75

0968-00803 1200-A KICK—UR-CPU RED

0968-00803 1300-B KICK—UR-CPU RED

0968-00803 1400-C. KICK—UR-CPU RED

0968-00803 1500-D KICK—UR-CPU RED

0968-00803 1600-E KICK—UR-CPU RED

0968-00803 1700-F KICK—UR-CPU RED KICK-MAN UPRIGHT CPU EPROMS VERSION NO. 2

0968-00803 1800-G KICK—UR-CPU BLUE

0968-00803 1900-H KICK—UR-CPU BLUE

i Gre)

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C. BOARD to FUNCTION PROPERLY!!

5-13

Page 76

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 77

KICK-MAN UPRIGHT VID. GEN. EPROMS VERSION NO. 2

a Ts Lt =

—+ CRxT_OCERE DD(om.a

o

NTne]wsNanSnera

$e

FR Seeae cra)BeCD feat
uyCenaMoog wauswemn
aDGD> @D
=vee [eas tais[eeuo
K 6 13Kc. KemeKe Zo
ve18 cg a4aae

com fears)

Heue *HaChHe |HI

>

(aE), ed Se

FeFSra i rsF2

ep De &

eses"e4es e2°
oToepao4osbecs
Gp emmyER,Fa) GD ED_
.Pesics

ed => «> € 7

karoep,.ee _
ar’aeas”AaaSAz- po
PrGDPed1ecITD) Grey Ge

0968-00803 2900-D KICK—UR-VG BLUE

0968-00803 2800-C. KICK—UR-VG BLUE

0968-00803 2700-B KICK—UR-VG BLUE

0968-00803 2600-A KICK—UR-VG BLUE

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C. BOARD to FUNCTION PROPERLY!

5-15

Page 78

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 79

KICK-MAN MINI AND COCKTAIL VID. GEN. EPROMS VERSION NO. 1

vs L 1 ¢ a4 [ ] v3

- CANT OCERZ 1)Ces oD=F
ni,ne]ue Na Newe] [we

aD ee Ce see GD Se,

=tated wee) [eee“s te 7

ur? L 6 icg. cg us| us" [ee Lt

na wa] fx

3 ve] feat ay ns 2 | ca LB &

sas 0513-00803

wews osoe oe oe2100-D

care 7D BQ > ae KICK—M&C-VG

*meYELLOW
rere re] oe rea

7 ie

z= eb GevA
5= '%0513-00803
cerea] te rephot
oveGD faze) Zp GadED, KICK--M&C-VG

= YELLOW

-:: _ =-GD0513-00803
e? © 8 ics €8 csLce1900-B

oD GD eD 2), ED cr) eo KICK—M&C-VG _ YELLOW a7 os as a4 Bs” e2

tes.ies.fern

GB [re ee ee

o> es_ :es0513-00803

a te ral [ae he Ta 1800-4

ey oD aD => op ee<>Sow

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.-C. BOARD to FUNCTION PROPERLY!!

5-17

Page 80

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 81

KICK-MAN MINI AND COCKTAIL VID. GEN. EPROMS VERSION NO. 3

srw sem 000 ann zorm pm a F | | rar) II re Ofc Cas el + cz +

NT Ke ne na we | we wt ap cre CeD, GD coal “7 we ‘es ual] us we wi

ur es, 1 © as ua wy [ee ui =D Fane Fa ED | Teg kegs 7 a7 a 0

Tr 18 es Ts a] [asr-a} Crus ™ we we wa a fe] ff Ce, = ae & 3D iD oe? a ra a 7 or] 0513-00803 wz 2900-D [D, zp S GD awe KICK—-M&C-VG re] re pa my = PURPLE i a ED GBS fa) om ics es? 8 | [ ea m3 e2 or ae 00-C pms. Ga GD [eraz)* Ga GD De KICK —M&C-VG o7 De os Da Ds De ties PURPLE as 1 ep EP Re, > cord cm ar ce seal car ws Ww cozy 0513-00603 cz em cars Cos), = &> cor) a KICK—M&C-VG : + PURPLE ep oD eS = eD ee

  • i 0513-00803 aT te] nm] a] Lee ae as 2600-A
  • KICK—M&C-VG ED Kary ee zD e ee Sie

The above EPROM COMBINATIONS (indicated by LABEL NUMBER AND COLOR) are the ONLY ones that will enable this P.C. BOARD to FUNCTION PROPERLY!

5-19

Page 82

707U0W “AL IA NOA ANVHL iNOA d14aH OL AQVAY GNVLS SHO.LNGIYLSIG HNO GNV 44VLS HNO “SHadVd SAWVS YNOA HLIM GAadIAOud YAEINNN S3euS TNOL SHL LV ANVdNOO SNIENLOVANNVW AVMCIN YO HOLNEIHLSIG HNOA LOVLNOO ASV41d ‘SNOILSSNOD SAVH TIHLS GNV NOILOAS SIHL HDNOYHL AVS" NOA Jl “HOLINOW ‘AL SAWV9D HISHL ONIYIVdSY ONV DNILOOHS31ENOUL NI 3SHD40 SOINOYLOSTS NV LNOHLIM ASOHL AIV OL GSGN3LNI SI GNV YANNVW GNVLSYSGNN OL ASV4 NV NI C101 SI NOILOAS SIHL NI GANIVLNOO NOILVWHOANI SHL ‘SLON 3SV31d

Page 83

Color T.V.

Color T.V Monitor

Introduction: (How to use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual! will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. if you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatment of the subject can be found in the technical sections of bookstores.

If you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 84

Symptom Diagnosis

. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). e Bad yoke. e Bad vertical output section. e Open fusible resistor in vertical section. ¢ Bad height control. e Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). e Bad yoke. @ Open width coil. e@ Open part in horizontal output section. Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity, . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.

. Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking control set too high. . Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit).

6-2 10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator transistor, 1C, or circuit. B. No sync from logic board.

Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.), B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.

Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.

No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).

No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.

No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. mMmoOOW>

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor.

Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 85

21.

23. Moving bars in picture: A.

B. Ground connector off between monitor and logic boards. Defect in the power supply (see wavy picture symptom).

Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.

Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.

B. Shorted horizontal output transistor. c. D. Defective high voltage disabling circuit. Crack(s) somewhere on main chassis board.

  • Can't adjust purity or convergence:

A.

ow Use a degausser to demagnetize the picture tube carefully following your degausser's instructions. Picture tube defective. Metal foreign material is in picture tube shield. Nearby equipment is electromagnetically interferring. The poles of the earth are pulling off the purity. Poor focus or width of picture.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SY WN INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE

6-3 IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

iO as FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 86

COLLECTOR To COLLECTOR Ka

BASE ————- BASE ———— EMITTER Se EMITTER mT

NPN TRANSISTOR PNP TRANSISTOR

' Ww

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+ ;

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

hog & GROUND

6-4

Page 87

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voitage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first itimplodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole. Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very APON

6-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handting the picture tube.

To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. Ifthe controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voitages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a probfem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 88

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and ashort is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.

NOTE: DO NOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a smail wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows acharging action. As they suck up Current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 89

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz).

The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information wil! be explained along with the oscillator shortly. The color informatior: is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION — After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn't mess up since it is assmebled like an orderly jigsaw puzzle, but so fast that you can’t see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes onits journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” or 19" color monitor uses transistors for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit !C501 for its sync section. The idea is all the same. The output to the vertical amplifying transistors for all monitors must be a sawtooth wave form, sort of like a bunch of pyramids, racing to the yoke's vertical coils at 60 times a second.

Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set. The amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.

6-7 The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Again, Wells Gardner uses transistors for the horizontal oscillator, and Electrohome uses the other side of IC501. Still, the effect is the same. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillators frequencies must match, so the picture doesn't appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it a smooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.

COLOR CIRCUITS The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There only two, one for the red and one for the green. The

Page 90

blue doesn’t have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section.

The beam limiter helps control the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check the emitter on TR502 of the Wells Gardner monitors; or the emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Wells Gardner = 127VDC Electrohome = 120VDC

The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, the GO7-FBO or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuits work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with, assuming you can’t find the brand name written on it anywhere, is to see if there are two. circuit boards rising up from the chassis toward the picture tube neck. in other words, they stand up, or are perpendicular to the chassis, with a black plastic bracket holding them in place. This is a description of a Wells Gardner monitor. They use separate boards for main chunks of circuitry. Therefore, you have a “power board” (the power supply), an “interface board” (the interface section), and a “horizontal/ vertical board” (for the deflection circuitry). Still, there are a few parts on the chassis, but most can be found on the board. An Electrohome monitor has no separate boards, except for the neck board, and just has a flat chassis.

Another good way to determine which monitor you have is to check the transistor call out numbers that are printed on the chassis next to the part. For instance, on the neck board, one of the color output transistors is TR401. If you look through the schematics or the parts lists, you will find TR401 in the Wells Gardner literature. On the other hand, the neck board transistor may say X101. X101 can be found in the Electrohome literature. So, all Wells Gardner transistor call outs begin with TR, and Electrohome transistor call outs start with an “X”.

Page 91

Parts Interchangeability Some parts can be interchanged on all of the monitors. Here are the rules:

1. You CAN swap the voltage regulator TR502 or X01 on any Wells Gardner or Electrohome 19 inch monitor. You CAN NOT swap the voltage regulator on the 13 inch Wells Gardner or Electrohome (G07-902) since the Electrohome uses an integrated circuit for the power supply.

You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance.

You CAN swap any capacitor between monitors that has the same capacitance, and voltage rating.

You CAN swap any 19 inch picture tube on the monitors.

  • You CAN NOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-904) monitor “flyback”. looks identical to the 19 inch Electrohome (G07-904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTERCHANGEABLE!
  • You CAN change any of the parts between the G07-904 and G07-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. lf there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.

6-9

Page 92

WELLS-GARDNER

VERTICAL RASTER

19”"COLORMONITORSCHEMATIC DIAGRAM
  • yosi-o0087-aol2z

INTERFACE BOARD P317

aw, 3%

,_}

R353. TR3S4 254825 25ci740/ 2501815 _2SA3015 7 250626 POSITION ADJUSTMENT

CENTEROOO.azoz
a—roa2neze

‘col vaM. 3%

Aa]=
voos [be|20291
Bhnassee
2roe fas3—4.5%
MAIN BOARD9wontnesea| daa.4
:B=

WORE COIL,

7402sci7a0zsors02@|
1740 5,aSciTSovag0:
BeUAP rea0s asaago TRIOr TOO TASeswnzo

usc.

|ro Peet)TRI04

mai aw 9%

e207

+—} +

.anenasnase
ov‘ee150‘30
*‘pov f teeaw, 5%88.8%00 8

PROTECTOR |

Fezo ve0v ‘HI

WORIZ, RASTER POSITION ADJ.

Rese 19 07 Cea ygy @OR EE ‘aUOIO7 POWER e503) + BOARD ERROR amp 922) 6%

OR OSE vs, Werrnor Lahn asarzsasee Boao [MT/0u) l F

-¥+f]
ikeonCS|ion
R502txSout fe naopeas
ZNae2sc ios5He Saee Se+ Ean be 2]
xy)“FeuseTEPete
ccceoets®“Se

Eo. 07

Cclans=

| =

ae [service re | service VP

decaussme————— - —____ —___---J=
©fe}-
.J escz0esL | egczz2[Do] escn

rp B62 |

6SG) BEE izeolleck Bsceze2 ote

Beate K4625A, K4626A, K4675A — 5816 J , 6-10

Page 93

VERT/HOR BOARD (MT/QJ)

Part No.DescriptionRet. No.Part No.Description

RESISTORS CAPACITORS (CONT.)

203X6500-628820 Ohm, * 5%, 1/8W Carbon6313203X0025-08747 uF, 50V Electrolytic
203x6500-90212k Ohm, = 5%, 1/8W CarbonC315203X0015-08210 uF, 25V Electrolytic
203X6500-92715k Ohm, * 5%, 1/8W CarbonC316203X1100-2203300 UF, SOV, + 10% Mylar
203X6500-88610k Ohm, + 5%, 1/8W CarbonC317202X8000-616100 pF, 50V, + 10% Ceramic
203X6501-241330k Ohm, + 5%, 1/8W Carbon351202X7000-2811500 pF, 50V,10%Ceramic
203X6500-645,1k Ohm, = 5%, 1/8W CarbonC352202X7000-2471000 pF, 50V, + 10% Ceramic
203X6500-6891.5k Ohm, * 5%, 1/8W CarbonC353203X1100-5730.022 uF, 50V, + 10% Mylar
203X6500-7242.2k Ohm, * 5%, 1/8W Carbon0355203X1100-8580.1 UF, SOV, + 10% Mylar
203X6501.285470k Ohm, * 5%, 1/8W CarbonC358203X0015-10547 uF, 25V Electrolytic
203X6501-06556k Ohm, * 5%, 1/8W CarbonC357203X1201-0130.015uF, 200V + 10% PP
203X6501-126100k Ohm, * 5%, 1/8W CarbonC358203X1201-0340.018 uF, 200V, + 10%PP
203X6001-32610k Ohm, = 5%, 1/8W CarbonC359203X0040-0134.7 uF, 160V Electrolytic
203X6501-04447k Ohm, + 5%, 1/8W CarbonC360202X7000-4820.01 uF, 50V, + 10% Ceramic
203X6500628820 Ohm, +1/8W CarbonC361203X1100-5090.015 uF; 50V, + 10% Mylar
203X6500-420120 Ohm, * 5%, 1/8W CarbonC362203X0025-05810 uF, 50V Electrolytic
203X6206-4412.2 Ohm, + 5%, 1/2W CarbonC363203X1205-4870.01 uF, 630V, + 10% PP
263X6500-169100 Ohm, = 5%, 1/8W CarbonC364202X7000-4820.01 uF, 50V, ‘* 10% Ceramic

203X6500-927 15k Ohm, + 5%, 1/8W Carbon

203X6700-509560 Ohm,1/2W Carbon

203X9100-121 22 Ohm, + 5%, 2W M.O. SEMICONDUCTORS

203X6500-6891.5K Ohm, +5%,1/8W Carbon
203X6500.98827k Ohm, * 5%, 1/8W CarbonTR301200X4082614Transistor, 25A826Q
203X6500-32647 Ohm, + 5%, 1/8W CarbonTR302200X3174-006Transistor, 28C1740Q
203X6500-628820 Ohm, + 5%, 1/8W CarbonTR303200X3174-006Transistor, 25817400
203X6500-88610k Ohm, + 5%, 1/8W CarbonR304200X3174-006Transistor, 28617400
203X6501-209220k Ohm, + 5%,1/BW CarbonTR305200X4049-081Transistor, 2SA490YLBGLI
203X6500-7242.2k Ohm, = 5%, 1/8W CarbonTR306200X3162-538Transistor, 25C1625YL8GLI
203X6500-92715k Ohm, = 5%, 1/8W CarbonR307200X3174-014Transistor, 25C1740R
203X6500-94418k Ohm, * 5%, 1/8W CarbonTR308200X3174-006Transistor, 28C17400
203X6500-783, 18W CarbonR351200X4085-415Transistor, 2SA854Q
203X6500-90212k Ohm, * 5%, 1/8W CarbonTR352200X3172-208Transistor, 2SC1722BKS
203X6500-561470 Onm,5%,1/8W CarbonTR353200X3174-006Transistor, 28017400
203X6500-7242.2k Ohm, + 5%,1/8W CarbonTR354200X4082-614Transistor, 2SA826Q
203X6500-6661.2k Ohm, + 5%, 1/8W Carbonx301201X2010-144Diode, (SI) 1S2473-T72
203X6501-08868k Ohm, = 5%, 1/8W Carbonx302201X2010-144Diode, (SI) 182473-T72
203X5500-47127 Ohm, = 5%, 1/4W Comp.X303200X8000-026Diode, (GE), INGOTVGL
203X6000-9381.2k Ohm, * 5%, V/8W Carbonx304200X8010-165Diode (St) 1SS81
203X6500-6661.2k Ohm, * 5%, 1/8W CarbonX305201X2010-165Diode (S!) 1SS81
203x9014-98847k Ohm, * 5%, 1W MO.X306201X2010-165Diode (S!) 1SS81
203X6700-98956k Ohm, * 5%, 1/2W Carbonx307200X8010-102Diode (Sl) MA26W
203X6001-1483.3k Ohm,1/8W Carbonx308200X8010-094Diode (SI) 1S2473
340X2222.7342.2k Ohm,. 122 Carbonx351201X2010-144Diode (St) 182473-T72
203X6500-7853.9k Ohm,1/W Carbonx352201X2010-144Diode (Sl) 182473-172
203x6500-7623.3k Ohm,1a CarbonX383201X2010-144Diode (S!) 1$2473-T72
302X6100-9611k Ohm, * 5%, 1/4W Carbonx354201X2010-144Diode (SI) 182473-172
203X6104-7512.7k Onm, + 5%, 1/4W CarbonX355200x8220-851Diode (Zener) RD10EB!
204x2122-093Varistor, 250K Ohm, Vert. HoldX366200X8100-130Diode (HS) RU-1 0.3 US

204X2114-065 Varistor, 20K Ohm, Vert. Size 204x2114-059 Varistor, 50K Ohm, Hor. Hold MISCELLANEOUS

CAPACITORS4301204x9300-958Socket, 6 Pin
301203X1100-9280.15 uF, 50V, + 10% Mylar1302204X9300-958Socket, 6 Pin
C302203X1100-5730.022 uF, 50V, + 10%MyiarP301204X9601-195Plug, 6 Pin
C304203X 1100-858.0.1 uF, 50V, + 10%MylarP302204X9601-195,Plug, 6 Pin
C306203X0025-02622 uF. 50V, ElectrolyticTH301201X0000-534Thermistor
307203X1100-9280.19 uF, SOV, = 10% Mylar
C309203X1100-8580.1 uF, 50V, + 10%Mylar
310203X0010-01122 uF, 16V ElectrolyticTRANSFORMERS & COILS
c31t203X0020-0991000 uF, 35V Electrolytic
e312202X7000-4690.0082 uF, 50V, + 10% CeramicL351201X5200-091Coll, Horiz. Osc.

POWER BOARD (MV)

503203X0010-01122 uF, 16V Electrolytic
RESISTORS551203X0005-046220 uF, 10V Electrolytic
R501204x 1725-052180 Ohm, = 10%, 15W WW
R502203X6000-608100 Ohm, + 5%, 1/8W CarbonSEMICONDUCTORS
R503203X6000-9601k Ohm, = 5%, 1/8W Carbon
R504203X6000-879560 Ohm, + 5%, 1/8W CarbonR501200X3174-006Transistor, 28C1740Q
R505,203x9014-965,39k Ohm, + 5%, 1W MO.Ak TR5O2200X3145-404Transistor, 2561454
R506203X6500-8426.8k Ohm, + 5%,1/8W CarbonR551200X3172-305Transistor, 2801723
R5S1203X6500-420120 Ohm, + 5%, 1/8W Carbonx501201X2230-042Diode, (S!) Zener EQB01-06V
R501204X2050-001Varistor Vert. Adjx502201x2010-144Diode, (SI) 12473-7172

CAPACITORS MISCELLANEOUS

501203x0040-02010 uF, 160V Electrolytic501204X9300-958Socket, 6 Pin
C502202X7000-2811500 pF, 50V, * 10% CeramicP501204X9601-195Plug, 6 Pin
THSO1201X0000-618Thermistor

6-11 NECK BOARD (MS/QG)

Part No.DescriptionRet. No.Part No.Description

RESISTORS

ed2eaxesn0 708felon a Be dawnC403202X7000-2471000 pF, 50V, 10% Ceramic
aos303xe800-70918k Ohm = 5% 18W CarbonC404202X7110-0191500 pF, 2kV' + 10% Ceramic
aoa303x6800-447150 Ohin = 5% BW CarbonC405202X7150-018100 pF, 12kV, # 10% Ceramic
a203X6500-481220 Ohm # 5% SW CarbonC408202X7050-483.01 uF, 500V,' + 10% Ceramic
Foe203X6500-447450 Ohm = 5% V8W CarbonC407202X7110-0191500 pF, 2kV + 10% Ceramic
R407203X6500-508270 Ohm + 5% 1/8W CarbonC408202X8000-55068 pF, SOV, + 10% Ceramic
R408203X6500-508270 Ohm + 5% 1/8W CarbonCaos202X8000-55068 pF, SOV, =Ceramic
R409203X6500-8004.7k Ohm + 5% 1/8W CarbonCAO,202X8000-55068 pF, Sov, =Ceramic
Rs10203X6500-8004.7k Ohm418 Carbon
Ratt203X6500-8004.7k Ohm1/8W Carbon
Ra12203X9104-80912k Ohm2.0W Metal Oxide
RaI13203X9104-80912k Ohm * 5% 2.0W Metal OxideSEMICONDUCTORS
Raid203X9104-80912k Onm + 5% 2.0W Metal Oxide
Ra15203X5601-3132.7k Ohm = 10% 1/2W Comp.TRAO1200x3206-800Transistor, 2862068, 2SC1514
R416203X5601-3132.7k Ohm = 10% 1/2W Comp.(R output)
R417203X5601-3132.7k Ohm *10% 1/2W Comp.TR402200X3206-800Transistor, 25C2068, 2SC1514
RAB203X5602.254470k Ohm * 10% 1/2W Comp.(G output),
R419203X5602-185330k Ohm + 10% 1/2W Comp.:
R422203X9105-1171.0 Ohm10% 2W Metal Oxide40300%9206-800We eatpugy 7302068, 2501514
R423203X5102-155270k Ohm * 5% 1/4W Carbon‘
VR401204X2115-014500 Ohm Varistor R Drivecespor 100-128pings 182967 (protector)
vR402204X2115-014500 Ohm Varistor B Drivex408sox sooiode,1S2367 (protector)
VR403204X2115-0065k Ohm Varistor R CutoffAXE 10026Diode, 182367 (protector)
R404204X2115-0065k Ohm Varistor G Cutoff
R405204X2115-0065k Ohm Varistor B Cutoff
R406204x2000-0251M Ohm Varistor ScreenMISCELLANEOUS
CAPACITORSJ401208X5003-729Socket, 5 Pin
1402206X5003-983Socket, 3 Pin
c401202X7000-2471000 pF, 50V, 10% CeramicP401204X9600-329Plug, 5 Pin
C402202X7000-2471000 pF, 50V, 10% Ceramic402204Xx9600-254Plug, 3 Pin

4 297X2000-072 HIGH VOLTAGE ASSEMBLY (1701) a* R701 vR702 x701 X702 X703

R201 R203 R204 R206 R207 R208 R209 R210 R211 R212 R213 R214 R215 R216 VR201 204X 1625-058 3.3 Ohm, + 10% 10W WW Resistor 204X3901-125 Focus Control Diode (Si HV) Diode (SI HV) @ Part of T701 Diode (SI HV)

RESISTORS

340X3910-93491 Ohm, 5%,1/2W Carbon
340X3102-9341k Ohm, 5%,1/2W Carbon
340X2101-934100 Ohm, 5%,1/4W Carbon

340X3331-944 330 Ohm, 10%, 1/2W Carbon

340X3102-9341k Ohm, 5%,1/2W Carbon

340X2152-934 1.5k Ohm, 5%, 1/4W Carbon 340X2101-934 , 14W Carbon 340X3102-934 1/2W Carbon 340X2331-934 , 4W Carbon 340X2331-934 %e, 1/4W Carbon 340X2331-934 330 Ohm, 5%, 1/4W Carbon 340X2201.934 114W Carbon 340X2201-934 , 5%, 14W Carbon 340X2201.934 200 Ohm, 5%, 1/4W Carbon 40X0590-017 1.5k Ohm, Black Level Control CAPACITORS 45X0524-038 1000 uF, 16V Electrolytic FINAL ASSEMBLY PARTS 4% 88X-0129-506 38A5554-000 205x9800-256 Axx 202X1110-810 208X2000-946 297X2000-072 6A0397 9A2753-003

INTERFACE BOARD (P305) (MODEL 19K 4606)

TR201 TR202 TR203 TR204 TR205, TR206 TR207 TR208 TR209 20201 20202

J201 J202 J203 P201 P202

6-12 19VJTP22 Pix Tube Assy. Purity Shid/Degaussing Lateral/Purity Assembly Yoke, Deflection CRT Socket HV Unit (T701) Plug, Line Cord Degaussing Coll (L701)

SEMICONDUCTORS 86X0121-001 86X0121-001 86X0121.001 86X0066-001 86X0066-001 86X0066-001 86X0121.001 86X0121-001 86X0121.001 66X0040-018 66X0040-019 Transistor (NPN) Transistor (NPN) Transistor (NPN) Transistor (PNP) Transistor (PNP) Transistor (PNP) Transistor (NNP) Transistor (NPN) Transistor (NPN) Diode, Zener, 6.8v, 5%, 0.5W Diode, Zener, 3.9v, 5%, 0.5W

MISCELLANEOUS 204X9300-958 204X9300-958 206X5019-207 204X9601-195, 204X9601-195, 204X9600-845 6A0393-006 Socket, 6 Pin Socket, 6 Pin Socket, 4 Pin Plug, 6 Pin Plug, 6 Pin Plug, 4 Pin Plug, 6 Pin

Page 94

segene ware Blue onten RED XIOI-XI03 ond X10 VIDEO AMP. 28C454C snouno X102.X104 and _XI06 VIDEO AMP. 25A673C

& crc

}x301,x302,x308,x308 SU-3032A CRT SOCKET ISyNC AMP. 2Scas4c or gecieas

X303 BEAM LIMITER 2SA673 Pe. [3304 BLANKING fae | 28casac or zicices

ate X901 POWER DRIVE 25C 2688 ne X.902 ERROR AMP 2SC1890 | Fes

caon pee nov anf x04 28ciioea, ascias4 POWER REGULATOR ro, fe}

ale

aye rial

‘06 Pim TRARY

z am, Schematic Notes Unless otherwise specified Resistance: ({2) (K--KQ, MM), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1» (yF) working voltage -> 50 (V) ceramic capacitor ses Inductance: (v H) OY TION YORE Electrolytic Cap: Capacitance Value (yF)/working voltage (V), NP - non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. nr Hor ENT SU-1133A Oat a oe oF “tit MAIN PCB ASSY rece) 2 indicates test point connection X70| X-RAY PROTECTOR 2801 HORE ay Beg OUT — ° ; 28C454C or 2SCI685 aeeeey SesatceeN zeeee or ah indicates chassis ground unless otherwise specified 250820 << Hz it r ACIZ0V 60H:/S0Hz indicates cycles per second s10% For safety purposes (and continuing reliability) a replace all components marked with safety syrnbol with identical type.

NOTE: FR ~ fusible resistor —e3-:

00-4147-04 Parts identification on circuit boards:

G07-CBo e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

6-13

Page 95

REPLACEMENT PARTS LIST - ELECTROHOME 19”’ MONITOR

special characteristics important to safety. Components identified by the A symbol in the PARTS LIST and on the Schematic have

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.
Comp. R: Composition ResistorM Cap
OMR: Oxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MF R : Metal Film Resistor

CMF R: Coating Metal Film ResistorMM Cap.
UNF R: Nonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will.help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass’y Purity Shield Ass'y

6-14 Part Number SU-1133A SU-3032A 07-220083-03 Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19” A AXDeflection Yoke PC Magnet A A\Flyback Transf. A ASHVR ROS UNF Resistor 2209,25W K C04 C Capacitor 150pF, AC1.5KV X01 Si. Transistor x02 Si. Transistor sc Screw #8-3, sc Screw % x % Pix Tube Mtg. (4) WA Pyramidal Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Brkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil D911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pcs.) c911 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symbol Description

R3105VvR 200
R3106VvR 200
R3113VvR 5K
R3114vR 5K
R3115vR 5K
R3116OMR 10KQ2W J
R3117OMR 10K Q2W J
R3118OMR 10KQ2W J

R3119 Comp. R 3.3KQ%W K R3120 Comp. R 3.3KQ%W K C3121 Comp. R 3.3KQ%W K

Capacitors Symbol Description C3107 E Cap. 10uF 250V A C3108 C Cap. 1000pF DC1400V P

Coils Symbol Description L3101 Peaking Coil

6-15 Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-03 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part. Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRGO029J-103 QRGO029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS3EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 96

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description Si. Transistor Si. Transistor Si. Transistor

Description A\CRT Socket

Main PCB Ass’y (SU-1133A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 4A1503 R1504 R1509 Ri512 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 41703 ASR1704 AR1901 R1902 R1903 R1904 R1905, 4Q1908 AXR1909 R1910 A\FR1901

Capacitors Symbol C1301 1402 1407 C1411 C1412 C1508 AC1512 AC1513 201514 C1515 C1520 C1523 C1524 4c1531 C1532 C1904 1905 Description Vv R 2002 Vv R 2002 CMF R 6B89NWJ OM = R 3.3KQ1WJ OM = R 27KQIW J OM R 12KQ2WJ v R 10KQ AF R 6822W K ACMF RR 11.8K9L.4W +1% v R 5KQ OM = R 10KQ2W J OM R B.2K22W J OM =A 82022W J CMF R 8221WJ CMF R 4791WJ OM R 68L2W I OM R 39021WJ ZN R ZN R ACMF = R3924W +1% ACMF RR 7.68KQ.4W +1% AsPosistor UNF Ro 2Q7WK CMF R 4.793WJ OM = R 10KQ2W 4 OM = R18KIIWS ACMF RR 472.%W 41% Vv R 2kQ ACMF R_ 2.74K QW +1% AF R 2202%W K

Description BPE Cap. 33uF 50V A Tan. Cap. 2.2uF 16V K E Cap. 4.7uF 6.3V A E Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600uF SOV J APP Cap. 2000pF DC1500V J A\PP Cap. 2000pF DC1500V J ASPP_ Cap. 2000pF DC1500V J PP Cap. 0.53uF DC1200V J BPE Cap. 3.3uF 50V A E Cap. 1uF 160V A M_— Cap. 0.1uF 200V K A\PP Cap. 2000pF DC1500V J APP Cap. 1500pF DC1500V J E Cap.

  • Cap. 10uF 250V A

6-16 Part Number 28C1514VC 2SC1514VC 28C1514VC

Part Number A76068

Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRG019J-332 QRG019J-272 QRG026J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO026J-103Z QRGO19J-183 QRV122F-470Z QVPSAOB-023E. QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEE51CK-225B QEW51JA-475 QEWS2CA-107 QEWS2CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEW52EA-106

Page 97

Coils Symbol 1502 1503 11504

Transformers Symbol 71501 T1503

Semiconductors Symbol 101501

X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 X1902

D1101 D1102 D1103 01301 D1401 D1402

D1503 D1504 D1505 D1506 D1507 D1508 Axp1701 A\D1901 AxD1902 AD1903 A\D1904 A\D1905

Miscellaneous Symbol AXF1901 AXF1902

Description Part Number

Linarity Coil A39835 Width Coil C30380-A Heater Choke C30445-A

Hor. Drive Transf. A46022-BM Side Pin Transf. C39050-A

Ic HA11244

Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 28C1685(R) Si. Transistor 2SA673(C) Si, Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 28D478 Si. Transistor 28D478 Si. Transistor 28C2610BK Si. Transistor 2SC2688 (K.L.M.) Si. Transistor 2SC 180A (E.F.) Si. Diode WO6A Si. Diode WO6A Si. Diode WO6A Si. Diode 18Z473H Si. Diode 1SZ473H Zener Diode RD10F(C) Si. Diode HF-1 Si. Diode VOSE Zener Diode RD11E(B) Si. Diode WO6A Si. Diode 1SS81 Si. Diode 1SZ473H AXZener Diode RD20Ev2 ASi. Diode 1S1887A ASi. Diode 1S1887A ASSi. Diode 1S1887A ASi. Diode 181887A AdZener Diode RD6.8EV3

AsFuse 1.254 QMF53U1-1R25S ANUL Fuse 3A QMF66U1-3R0S

6-17

Page 98

on O34 IN PCB ASSY aco cAten aust XI01XIO3 end XI0S VIDEO AMP. 2SC454C g 25¢1685 x102.x104 and X106 VIDEO_AMP 2SA673C

X304 BLANKING 2scasac

x304 X303 BEAM LIMITER 2SA673 xo, 4302 1305, x206 SYNC A |z8casae or ascieas Morxid3 Rigs VioeO OUTPUT. 25cagii or 28cisiav

Aci20V Gom/sone 210% Ta SK

03 gf

om) (oer) ” x01 sles rom 84-103 [7] X10

18 [SU-3016 A | CRT SOCKET PCB ASSY J

X701 X-RAY PROTECTOR 2SC434C or 250 1685

6-18 a

28C26iI of 28C26108K EsoP WE, ascasrw 280898 or 250869 our 4, sont wearen

G07-FBO

00-4147-03 Schematic Notes Unless otherwise specified Resistance: () (K*KQ, MM), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1 (yF) working voltage -» 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value ( F)/working voltage (V), NP - non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection oh indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability)

A replace all components marked with safety symbol with

identical type.

NOTE: FR - fusible resistor «

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 99

REPLACEMENT PARTS LIST - ELECTROHOME 13”’ MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CRCarbon ResistorC Cap.
Comp. RComposition ResistorM Cap
OMROxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MFR : Metal Film Resistor

CMF R: Coating Metal Film ResistorMM Cap.
UNF R: Nonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyro! Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

Symbol

Outside of the P.C.B. Ass’y Symbol Avo1 ApyY01

AR AROS Aco4 x01 Ico1 Lo1

BR BR sc WA

CH Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y

Description AsPicture Tube A\Deflection Yoke PC Magnet Wedge A\Flyback Transf. AFocus V R UNF Resistor 2202, 25W. K ASC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Degausing Coil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Ass'y. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) Clip P.C.B. Support (2) Ground Lug Chassis Base

6-19 Part Number

SU-1103A, SU-3016A

Part Number 370ESB22(E) C29123-V A76366-A 30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass'y (SU-1103A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 A\FR1401 AsR1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 A\R1703 ASR1704 AXR1901 R1902 R1903 R1904 A\FR1901

Capacitors Symbol 1402 C1411 C1412 C1508 c1511 AC1512 AC1513 AC1514 C1515 C1520 C1524 1904 C1905 C1907

Coils Symbol L1501 L1502 L1503 11504 L1901

Transformers Symbol 71501 71503 Descripti voeoR voR CMF R OM R OM R OM R voR AF OR ASCMF R voR OM R OM R OM R CMF R CMF R OM R OM R ZN R ZN R ACMF R A\CMF R A’Posistor UNF R CMF R OM R AF oR

Descriptl Tan. Cap. E Cap. E Cap. PP. Cap. E Cap. SPP Cap. jon 2002 2002. 68Q1W J 3.3KQ1W J 2.7KQIW J 12KQ2W J 10KQ. 6822W K 11,.8KQYUW +1% 5KQ 10KQ2W J 5.6KQ2W J 68022W J 8.2Q1W J 4.701W J 56Q2W J 39021W J

39K QW +1% 7.68K QYW +1%

2Q7W K 5.623W J 1OKQ2W J 2202%W K

jon

2.2uF 16V K 100uF 160V A 3.3uF 160V A 5600pF 50V J 47uF 160V A 2000pF DC1500V J A\pP Cap. 2000pF DC1500V J AXPP Cap. PP Cap. BPE Cap. M_ Cap. 2500pF DC1500V J 0.53uF DC1200V K 1uF 50V A 0.1uF 200V K E Cap. E Cap. A\MM Cap. 10uF 250V A 0.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transf. Side Pin Transf.

6-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRGO019J-332 QRGO019J-272 QRG029J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG029J-562 QRG029J-681 QRX019J-8R2 QRX019J-497 ORG029J-560 ORGO019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M

Part Number

QEES1CK-225B QEW52CA-107 QEWS52CA-335 QFP31HJ-562 QEWS52CA-476S » QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS52EA-106 QFZ9008-104

Part Number A75360-6 A39934 €30380-A C30333-A A39475-J

Part Number A46022-BM C39050-A

Page 100

Semiconductors Symbol 101501

X1101 x1102 X1103 X1104 X1105 X1106 x1301 X1302 X1303 X1304 X1305 x1401 x1402 X1501 X1701 D1101 01102 01103 01301 01401 D1402 01503 01504 01505 D1506 01507 01508 Axp1701 4\D1901 4A\D1902 A\D1903 4801904

Miscellaneous Symbol ASF1901 A\F1902 Description 1c.

Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Zener Diode Si. Si. . Diode . Diode Zener Diode Si Si Si . Diode |. Diode |. Diode A\Zener Diode ASi ASi ASi ASi |. Diode . Diode . Diode . Diode

Description A\Fuse 1A ANUL Fuse 3A

6-21 Pari Number HA11244

2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 28D478 28D478 2SC2610BK 2SC1685(P-S) ‘WO6A WO6A WO6A 182473H 1$2473H RD10F(C) HF-1 VOSE RO11E(B) ‘WO6A 18881 182473H RU20EV2 1$1887A 181887A 1S1887A 1S1887A

Part Number QMF53U1-1R0S QMF66U1-3R0S,

Page 101

CRT Socket P.C.B. Ass'y (SU-3016A) Parts List

Resistors Symbol R3105 R3106 R3113 R3114 R3115, 3116 R3117 R3118 R3119 R3120 R3121

Capacitors Symbol 3107 C3108

Coils Symbol 13101

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description 2002 2002, 5K 5KQ 5KQ 10K 22W J 10KQ2W J OM R 10K22W J Comp. R 3.3K2%WK Comp. R 3.3KQ%W K Comp. R 3.3KQYW K oo<<<<< DBDDVDDIDID iM IM

Description E Cap. 10uF 250V A Cap. 1000pF DC1400v P

Description Peaking coil

Description Si. Transistor Si. Transistor Si. Transistor

Description ACRT Socket

6-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 j QRZ0039-332 QRZ0039-332

Part Number QEWS2EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2802611 28C2611 28C2611

Part Number A75522

Page 102

Vil Schematics and Wiring Diagrams

Page 103

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 104

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 105

MONITOR GND oi en ge MONITOR Zi | POWER i “ 2 ANP —<_) vACK

BRN-Oa

A890

CN- OFF \* sw

aay

lL, st env | J SAFETY (A082 90910 D000

coy

Tr-soa! | Leone J IIIIIA ISSIR OLEH

aaa

lo aw6 Gav-Bk for Sy rev te

VOLUME ©o-B8Is

Los i's Lod BINARY a

ANGLEen@
nas12 @L_ax-ale 1
hie1PINK lar |

\ 0-6 lie _ | Lis | coms 9 ervwli | = senegle | —su-wis — | e a4 aoe aula | he KICK ——suxeyis | | a swale | SOUND 1/0 ro, ow le! ~30008~AS6

_restow |e
i}BINARY.arar "
ANGLE,oeTah!
cECOcER=, >a
PAYER $1i\ver_hig

te 7 KEY 4

9 POS |awme let

Wek on

aose-s1391= 6000 |:a

hi i i vn _| L | J

COIN DOOR & szrn nen > gone TL 7 a id LIGHTS, i \ wre) 5 ues _¢—Khy xerlg Renee wer la) < | ia wx | waz es was {HY weaiulz . | 23 POS ra RETURN wanteo. | 25 ro

LOGIC_GRN v2 PI

CPU ACEA- 91399 — AOEE

KICK CT

MIDWAY MFG

sry '2

Nutt +e

\aRED
une'¢ERED

ccR

>L!tRED
1ir'x
1T“8
FILTERSe ieveowsve9" LOGIC HO+8
2J 3\ evover !34 iol OGIC_GNO_#Y-B
SSY:9 Pos! 4! 8VUNREG _¢ B-W! 4 i CONNJi*Y-8
1 27512 comaWHTis |''
KICK CTESV UNRES —« O-wig I"is! peserxvi0
‘> bt7| 5¥ COMyew? 'POWERit WV BATT= GRY
MOBI~ 00515—A0O31 2 pievunnes a ewie |SUPALYpeeSY)RN
9 i2v COM WHT '{cuA GNDYW

TepcrIES 4945- 00002-0000 os | oa ABER nT "7 082 90412-8000 7 Pos

lo Is lo 71 Key I \

int t_J MONITOR,

:

' ‘ys

\ Li 74 vipgo EN AGES ~ Aces

pare ee a)

Page 106

DESIGNATION #

e104 e102 e103 C104 C105 C106 C107 C108 C109 e110 eit c201 c202 6203 e208 C205 e206 cpt

R101 R102 R104 R105 R106 R107

R108 R110 Ratt Rin Ring Rita Rit

Ray R118 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 Ratt R212 R213 R214 R215, R216 R217 vR101,102

D104 Di02 D103 D104 D105 D106 D201 D202 0203 D204 DESIGNATION LIST

DESCRIPTION

4700ut Ax. ELECT. 470ut AX. ELECT “WE AX. CER, “ut AX. CER. 4701 AX. CER 470ut AX. ELECT. 190ut RD. TANT. tut RD. TANT. 4.7uf RO. TANT tut AX. CER, “tut AX. CER: LOtut MYLAR loagut MYLAR lotut MYLAR O47ut MYLAR 820p! AX. CER. <Otuf AX. CER tut AX. CER.

s8ohm 5W WIRES. SPACER @Borm 1/2W 5% 100hm SW W/RES. SPACER. 27ohm 1/4W 5% 2700hm 1/4W 5% 6.2K 1/4W 5%

1k 174 5% 1Gohm 15W W/RES. SPACER 6.8ohm 1/2W5% BBohm 1/2W 5% 1.2K 1/4W 5% 47ohm 1/4W 5% 1600hm 174 5%

5600nKm 1/4W 5% 1500hm 2W 2700hm 174W 5% 1.2K 1/4W 5% 11M 1/4W 5% 3.3M 1/4 8% 10M 174W 5% 100K 174W 5% 33K 1/6W 5% 2M 1/4W 5% 1M 1/4W 5% 1.2M 1/4W 5% 18K 1/4W 5% 78K 1/4W 5% 220K 1/4W 5% 3.9K 1/4 5% 1.2K 1/4 8% B20ohm 1W 10% 2700hm 1/40 5% 1000hm POT ANF AISF ANSE AISF AISF 14001 1N4148, 1N4t43, 1N4148 1N4001 1N4001 DESIGNATION +

u105

ui v2 va ua

Lior e108

FotA.16, FEL wi

a4

a6

ter

HSAt MHHSAT

swi-s, FEMH1.2 DESCRIPTION

2N2005, 2N2008 i 2Naaot

M205 REG. M305 REG. L390 N28

.22uH INDUCTOR BATTERY s6VDC SODEG-C 9/8K S-BLO FUSE FUSE CLP FERRITE BEAD Tie WRAP SPIN P.C. MOUNT CONN(MALE) | 1SPIN P.C. MOUNT CONN.CFEMALE) 15PIN P.C. MOUNT CONNAMALE) SPIN P.C. MOUNT CONNAMALE)

FUSE TAG SYSTEM TAG

HEAT SINK ASS'Y 1 MOUNTING HARD WARECHEAT Stk) 2-SCREW 4-WASHER. 2-HEXNUT

JUMPER WIRE FERRITE BEAD MOUNTING HARDWARE a

e108 oo pe f oe Can GD ecw | yy

p d

DIoe

Uglrome + + fue CMe: gmp

vs fe)

va PJ We

we

tor

CROSS REFFERENCE LIST

DESCRIPTION

SPIN P.C. MOUNT CONN. (MALE: 9PIN P.c. MOUNT GONN.(MALE) 1SPIN P.C. MOUNT CONN.(FEMA {SPIN P.C. MOUNT CONN.(MALE)

22AWG TAR BARE 2.5" Q'ty DESIGNATION ¢ PART +

y 4 8 0017-00021-0443 ee) 0017-00021-0425 Ler twa 0017-0002 1-441 15 0017-00021-0440

5 uwis. 0151-00087-0000 CROSS REFFERENCE LIST

DESCRIPTIONQ'tyDESIGNATION +
ATpI AX. CER.1108
8200 AX. CER.16208
Otut AX. CER1e208
tut MYLAR2201
0330! MYLAR1e202
047uf MYLAR1704
Aut AX. CER,56109,104,1:6.111,

Py

tut RAD. TANT1108
4.700 RAD. TANT1e109
400u! RAD. TANT1107
470u" AX. ELECT.2€102,106
470034 AX. ELECT.1101
A6onm 15W 5%1Rt10
1Bohm SW 5%1Riot
©.8ohm 1/20 5%1Ri
aOohm SW 5%1Rios
270mm AW 5%1105
A7onm /4W 5%1Rina
Bohm 1/20 5%2102,112
820hm 1W 10%1R216
1500hm 2W 5%1R18
1600hm 1/4W 5%1Riis
2T00hm 1/4W 5%3106,201,217.
S600hm 1/4W 5%1Rwy
1K 74W 5%1R108
1.2K 1/4w 5%3113,202,215
3.9K aw 5%1Rove
6.2K 1/4W 5%1R107
3K 1/40 5%1R207
75K (AW 5%2Ra11,212
100K 1/4W 5%1R206)
220K 1/4W 5%1R213
1M 1/4W 5%1200
1AM 174W 5%1R203
12M v4W 5%1R210
2M 174W 5%1R208
33M 1/4W 5%1R204
10M 174W 5%1R205,
1000hm POT2va101,102
ANSF RECTIFIER5D10-195
awaoo1a106,204.205
ania3201-203
2N2005,2102,105
2Na40110201
Laos REO2via
Lm39001us
4n281ua

BATTERY 3.6VOC 6ODEG-C 1 8101

FUSE 3/84 5-BLO1FL
FUSE CLIP2FO1A18
Tie WRAP1m1

PROJ. ENG : L. DEKKER. MO51-00945-B008 PART

0045-00811-0100FERRITE BEAD2Fei0017-00008-0225

0945-00816-0400 FERRITE MOUNTING HOW

(0945-008 16-01002FeMH1.20017-00033-0139
0940-008 16-0200-22uH INDUCTORL101(0945-00814-0200
0945-00816-0500FUSE TAG1Mos 1-00945-A004
0945-G0816-0300—_sysTEM TAG1Mos 1-00945-A009
0945-00811-0200P.c.B.1‘8080-904 12-8000

(0945-0081 1-0300

0945-00811-0400HEAT SINK ASS'Y1HsA14945-00008-0000

(0945-0081 1-0500 (SEE HS ASS'Y ORAWING "Hx NOTE”) 0945-00816-0600 4-40X10 SLTRND 2 — MHHSAIA,2A, 0017-00101-00727

oass-008 1-700{ 4-40 MEX NUT2MHHSAIE, 26. 0017-00103-0002

WSH4-120-.260-018 4 — MHHSA1B,10 0017-00104-0071 0945-00815-0100 wnneaee.20 0945-00815-0200 (0062-04703-1Xxx 0945-00812-0100 (0062-068B3- 1Xxx (0062-08653-1XXX (0062-098D3-1xxx (9062-104F5-1XXX

0945-20812-0200 (0062-124B3-1XXx (0062-13889-1xxx (0062-16283-1xXX 0062-17983 1XXX 0062-18383~1Xxx (0062-20783-1XXx (0062-21783-1%Xx (0062-25 183-1%Xx (0062-26983-1xxx (0062-27582-1Xxx (0062-20183-1%xx (0062-32982 1XXX (0062-22983-1Xxx (0062-327B3- 1Xxx (0062-33783- 1X¥x (0062-34783-1%Xx (0062-37 183-1XXx (0945-0081 4-0000

0945-00804-0200 10945-00804-0300 (0945-00804-0500

0945-00808-0300 (0945-00804-0400

(0945-00813-0100 (0945-00813-0200 (0945-00813-0300

(0017-00003-0377 ‘p045-00808-0400 0017-00003-0214 (0945-00814-0300

MIDWAY MFG. CO. fuseoon KOK

Mo EO GpER TRESS few este PWR SPLY 125VAW/CKT SPRT ve hee 2B freer A082-80412-B000 MOS! -00945-8006

7-4

Page 107

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 108

DESIGNATION DESCRIPTION ce 100 wt AX, ELECT. GP I-3, 5-10 Olt AX,CER. cPi2=20,22-27, cP29-33, 35,36, cP38-41,43-47, cP 49-54, 56-61, P6367, 69-71. €P4,11,21,28,34, lOuf 25V AX. TANT. 6P.37,42,48,55, cP 62,68. RIOI=119,201,202, 1K 1/4W 5% RMI,2 8PIN IK SIP RMS IOPIN IK SIP DESIGNATION Ie ie Ie Ic Ic Ic Ie

Ie ic Ic tc Ic Ic lc

ie Ic Ic ie Ic te ic

tc 1c ic tc

ie Ic

Ie Ic Ic Ic Ie

Ie Ic Ie Ic Ic

Ie Ie Ic Ic le Ic mmmmm CODTCCS 0000000 22000 br>rrer DESCRIPTION EPROM T4.sis7 74LSiST T4LSis7 74.sis7 74.LSIS7 74USi57

EPROM T4.si94 TaLsi9g racs32

aze 74832

EPROM T4Lsisa T4LS194 T4Ls32

TaLs32

EPROM TALsi94 T4Lsisa raLse73s 74.sis7 TaLsisT TaLs273

Ta si94 74Lsi94 TaLs37a TaLsis7 74.157

7400 74806 T4Ls 374 74S 187 748157

7aLS 86 T4Ls 20 74Ls283 74.8283 74s 283 7a csis7 DESIGNATION LiST

DESICNATION DESCRIPTION arn) 74S 86 ic 2 74174 ry 74874 lone 7ai75 Ic HS rai74 ic He T4LSis7

ove 74830 wou 7430 iou4 74.s273 us aze Ie v6 74.8157

Io Kt aie IoKe 7430 1c KS 474 eK 4 rate! Io K8 422 Io K6 24-2

eur 74.s20 ree 7408 ree 7474 lou 74.8283 es 422 Ie us 2u4-2 ram T4LSis7

oom 7430 Ic Me 7432 Io M3 74874 Io M4 74161 Io ws 422 Io m7 T4LS 157

lo wt 7430 lowe 7427 io N3 T4aus2e73 Ic Na 74s 2e3 IONS TALS 245 1c NG 7404 Ic nT 74LS157

ICS.Ai,81,C1,01. 28PIN IC SOCKET 1€85,6,C5,6, 22PIN IC SOCKET J5)K5,L5, MS. ICSK6,LE. 1BPIN IC SOCKET 43.4.5. 2OPIN AND 4 PIN SOCKET ows JUMPER WIRE. 881.2 BUSS BAR : a & P28 ws. awe" wr swe TE : arty DESCRIPTION

es Bt 1s ies ra 6 so

les Fics Zz Fa GD oo zy ce 1K 8 PIN SIP 1K 10 PIN SIP 2uia-2 7400 7404 GD os ea zp es 74804 7408 7aLs20 7427 E> GD

7430 74LS30 =

ies oom we D> ep FS 200m

£8 ics oro ra ree) aa [xcz7) 7432 74LS32 ra74

ies kao) cs 1s om 74874 7aLses TALSIST

em 74161 airs 74175 7aLsi94 7aLs245 ravse73 74.8283 Pad) ED

” lcs ED ce “tes ee 74.8374 93422

EPROM EPROM EPROM EPROM JUMPER WIRE BUSS BAR P.c. BOARD 4PIN SOCKET 20 PIN SOCKET 28 PIN SOCKET 22 PIN SOCKET

2 18 PIN SOCKET

' VIDEO GENERATOR 1 pt SOV AX, CER.

n 10 pf 25 v Ax. TANT. 100 pt 25V aK. ELECT. 1k 1/4 CRON. FLM. CROSS REFERENCE LIST

DESIGNATION

cP1-3, CP5-I0, cPie-20,cP22-27, P29-33,0P35,36, cp38-41,ce43-47, cP49-54,cP 56-61, (cP 63-67, CP69-7 P4,11,21,28,34,37, ch42,48,55, 62,68 PART NO.

0986-00800-2500

0986-00800-2400

c12 9986-00800-1800 RIOI-N19, 201,202. 0062-79B3~1XXX RMI, 2. (0986 -00804-1100 M3 (0986 -00804-1000 K6, U6. 0986-00803-2300 F2 09a6-00803-2800 Ne (0986-00803-8300 3 (0986 -00803-3100 Le 0986 -00803-3200 G2,u! (0986-00803-3400 ne (0986 -00803-3500 93,2, MINI (0986 -00803-3600 32 (0986-00803-4300 Me (0986-00803-4400 84,7,4,7, (0986-00803-3700, K3,L3 (0986-09803-4500 43, M3 (0986-00803-4100 sine (0986-00803-4200 A2,3,4,5,6,7, 05,6, £5,6,F5,6,66,H6, J6,LTSMT,NT. (0986 -00803-2400

KI Kama (0986-00803-2500 H2,5 0986 -00803-2600 Ha 0986-00803-2700 82,3,C2,3,02,3,£2,3. 0986-00803-2900 NS (0986-00803-3000 04,7,34,N3 (0986-00803-3800 63,4,5,L4,N4, (0986-00803-3900 Bara (0986-00803-4000 85,6,C5,6, 15, 0986-00804-0800 5,5, M5 at UY@Ap '0968- 00803-3400 KICK UPRIGHT OULY BI (vee) cl (vec) 1 (v6D) 0813-00803- 3000 KicK MINI @CT OULY owi-8 ‘0986-00805-0200 81,2 (0986-00804-0900 4080-91399-£000 o34s 0986-00804-0400 43,4,5 0986- 00804-0500 IeSAl,B1,c1,01 (0986-00804-0300 10885,6,c5,6, 0986-00804-0700 45, K5,L5,MS Wes KLE 0986-00804-0600

‘A080-91398-F 000

a PROJ. ENG. ATISH GHOSH q

  • — ier MIDWAY MFG. CO.

[Ao 12/11/81 ASSEMBLY DRAWING VIDEO SFNSPATOR Pc. A082-91399-FOO: IMOSI -00968-A0I6

7-6

Page 109

|-00806- F005 WiDWAY MFG. CO. VEO GENERATOR ‘8082-9199-£000 ‘| :

Page 110

7-8 DESIGNATION LIST DESIGNATION DESCRIPTION. DESIGNATION DESCRIPTION.

] ot

= CROSS_REFERENCE_LIST

DESCRIPTION, Gry, DESIGNATION PART NO, -DESGRIPTION QTY. DESIGNATION PART NO.

UPRIGHT OULY

MiNiacT uy

a

[CPU BOARD i A082-90009-F000 [**"

Page 111

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 112

“Sano 70 13082:90008-6000,

Page 113

7-11

Page 114

7-12 DESIGNATION LIST

DESIGNATION

Cl,c2 c3,c4 c5,c6 c7-Clo CPI cP2,cP3

RIR2 R3R4 R5-RB

u1,u2

Jl

J2

HSA1,2

MHI-MH4 DESCRIPTION

47 mf 2Sv rd.tant.

22mf6v|

470mf 6v ax.elect. Amf SOv ax.cr 220mf 25v ax.elect. mf SOv ax.ecr

2.7KN V4aw 5% CRBN, 270, moon “ TN Wew'' nt

MB3730

3 Pin STRT. KKI56

30""
2"“u

HEATSINK ASSY.

HEYCO BUSHING

DIM. TOLERANCES: UNLESS OTHERWISE SPEC.

FRACTIONAL, +1164 DECIMAL +.005 HOLE DIA. + .002—.000 ANGLE : .. £12° DO NOT SCALE DWG CONCENTRICITY T.1.R. 002 CROSS REFERENCE LIST

DESCRIPTION, QTY DESIGNATION PART NO.

Imf 50vaxcr6C?7CIO,0986-008001100

CP2CP3

47 mf 25vrdtant 2CIC2@986-008003100
22mf By" "2C3C40986-00800-1600
220mf 25vaxelec,1CPI0986-00800-3200
470mf 6v"2C5C60986-00800-1700
INV/2w 5%4RE-RB0062-026D3-1xxx
270V4w2-R3R40062-068B3-1XXx
27K2RLR20062-199B3-1XXX
MB37302.ulu20066 -188x x -Xx4x

PC BOARD |

2PINSTRTKKIS61J2
3"-"2JId2
4"""1vi
HEATSINK ASSY,2HSAI,

HSA2

HEYCO BUSHING 4 MHI-MH4 3000 -16367 - 0200 3000-16367 -0300 3000-16367 -0400

0986 - 00804-1800

0017-00042-0014

A080 -90910-D000

MOQ51-00986-D010 THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO.

MIDWAY MFG. CO. FRANKLIN PK., IL. 60131 A BALLY CO.

FINISH DUAL PWR. AMP. ASSY fraario: A082 -90910- D000 1 REVISIONS

051-00986-DOI0

Page 115

ho nto —

On NC,

L, AUDIO

L. SHIELD

KEY

V AUDIO RETURN

R. AUDIO

R.SHIELD

V AULID

R-

KEY

L+

N.C L, SHIELE

R2 C2 27K 4.7MF R

5 2 R. SHIELD + P

Vaupio

Vauplo

VaunDIO

25V

Vaupio _ RETURN an

THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO. MEONICK unvess oTHenwise spec. P= — MIDWAY MFG. CO. CONCENTRICITY T.1.R. .. .002 “VY, “12-14-81 FULL FRANKLIN PK., IL. 60131 A BALLY CO. FRACTIONAL +1164 DECIMAL + .005 HOLE DIA. + .002—.000 ANGLE +1/2° laa DO NOT SCALE DWG MATL REVISIONS

DUAL PWR AMP PART NO

A082-90910-DO0O MO 5 |-00986-DOlI

Page 116

7-14 C1

CP1-CP3

R101, 201 R102, 202 R103, 203

R04, 204

R105, 205 R106, 206 R107, 207 ul

u2

U3

U4

US, UB Jj

MHUS, MHU

P.C.1 DESIGNATION LIST

1Quf 25v TANT. AX.

«luf SOv AX. CER. BYPASS

820 ohm

10 K

200 K

240 K

1 meg. ohm

1K 200 ohm

LM3960

7474

74191

7414 GPTICAL LIMIT SW.

KK-1S6 VERT. (3,5) 6 (4) 5-40 SCREW

  • PLATE NUT AOBO-91391~-Co0o [—— LIMIT SW. SLOTS MUST BE INLINE, CHECK WITH .090 WIDE GAGE

MHUS MHUS CROSS REFERENCE LIST

10uf x.

«luf SOv AX. CER.

200 ohm 820 ohm

1K

10 K

200 K 240 K

1 meg. ohm

7414

7474 74191 Lm3900 OPTICAL LIMIT SH. KK-156 VERT. 3 PIN KK-158 VERT.S PIN 5-40 SCREW PLATE NUT

P.C. BOARD

DN DG NOT SCALE ONG. cP1-CP3 0968 -00800-0100 107,207 0062-130B3-1XXxx R1l01,201 0062-174B3-1Xxx R106,206 0062-179B3-1XXX R102,202 0062-22783-1XxX R103, 203 0062-28983-1Xxx 104,204 0062-293B3~1XXX R105, 205 0062-323B3-1XXxx U4 0968 -00804-0200 u2 0968 -00804-0300 U3 0968 -00804-0400

ul 0968-00804 -0500 US, UB 0968 -00804-0100 Ji 3000-16387 -0300 Jj 3000-16387-0500 MHUS, MHUB §=0017-00101-0084 MHUS, MHU6 §=0643-00112-00B0 A08O-91391-CO00

MIDWAY MFG. CO. FRANKLIN PK. ILL. PART NO.

MO51-00968-C003

Page 117

an tb" 1<|———_ _— |_TIL143 _ <2<

-——35 fadesle gelaoNOTES

2 ui-LM3300 A U2-7474

79 fd>et< 8 <;——_1U3-74191
u316U4-7414

uM 4 1 ydd>ol® 9 <_____02 fs T]

13lydo12 6 <}___08

1 2 5 —< 4 <—__EY

2 le, Yoo u2 3 | 5S <—_—__—_—_nd 3 lod 1 !_ 10 HF: nt

PROJECT ENG: C.MEDNICK

DO NOT SCALE ONG.

at MIDWAY MFG. CO. peate Fut FRANKLIN PK. ILL

hn BINARY ANGLE DECODER SCHEMATIC MOSI-O0968-C004

A082-91391-CO00

7-15

Page 118

Chip Number

MB8416 6116LP-4 9860-07 AXN-AXHD Z-80 CTC 0066-313BX-XXQX (MMC01) 0066-314BX-XXQX (MMC02) 0066-315BX-XXQX (MMC03) 0066-316BX-XXQX (MMC06) 0066-322BX-XXQX (MMC04) AY-3-8910 (8910) LM3900 MC3403 Function

Ram 2K x 8 Ram 2K x 8 PROM 828123 (SB2-A) Counter timer circuit H-T generator - custom V-T generator - custom Misc. V & H circuits - custom Misc. TTL circuits - custom NVR controller - custom Sound generator Quad operational amplifier Quad operational amplifier

Misc. Components

16.00 & 19.9 MHZ 2N4123 2N4403 MPSA70 TIP110 Z-TAL Transistor NPN Transistor PNP Transistor PNP Transistor NPN

7-7 Kick-Man Logic Boards Integrated Circuits

Chip Number Function

7400 Quad 2 input Nand 74LS02 Quad 2 input Nor 74LS04 Hex inverter 7406 Hex inverter open collector 7407 Hex buffer open collector 74LS08 Quad 2 input And 74LS20 Dual 4 input Nand 7427 Triple 3 input Nor 74LS30 8 input Nand 74LS32 Quad 2 input Or 74LS74 Dual “D” Flip-Flop 74LS86 Quad 2 input exclusive Or 7489 64 bit ram 16 x 4 74126 Quad buffer tri-state 74LS138 3 to 8 line decoder 74LS153 Dual 4 to 1 line multiplexer 74LS155 Dual 2 to 4 line decoder 74LS157 Quad 2 to 1 line multiplexer 74160 4 bit decade counter 74161 4 bit binary counter 74166 8 bit shift register 74LS174 Hex “D” Flip-Flop 74175 Quad “D” Flip-Flop 74LS191 Up/down binary counter 74LS194 8 bit shift register 74LS244 Octal buffer tri-state 74LS245 Octal buss transceiver 74LS273 Octal “D” Flip-Flop 74LS283 4 bit full adder 74LS367 Hex buss driver 74LS374 Octal “D” Flip-Flop tri-state 74LS670 4x 4 register files 4017 Decade counter/divider 14016 Quad analog switch 14024 7 stage ripple counter 14053 Triple 2 channel analog multiplexer Z80 CPU 2.5 MHz Z80A CPU 4 MHz D780C CPU 2.5 MHz D780C-1 CPU 4 MHz TMS2564 8K x 8 EPROM MBM2732 4K x 8 EPROM HN462532 4K x 8 EPROM 2114 Ram 1K x 4 93422 Ram 256 x 4 M58725 Ram 2K x8 4801AN-90 Ram 1K x8 4118A-4 Ram 1K x 8

7-16