CATHODE RAY TOMES

Up Your Alley

Alley Master (Cinematronics, 1986) · Manual · 42 pages · 16 sections · original scan

Page 1

e Manual

nand Maintenance:

Operatio

Page 2

UP YOUR ALLEY ~ OPERATION AND MAINTENANCE MANUAL

UP YOUR ALLEY

INSTALLATION AND MAINTENANCE

THE LELAND CORPORATION

CINEMAT SYSTEM

1841 Friendship Drive

El Cajon, California 92020

Phone 619-562-7000

Telex: CINTRON 4974293

FAX: 619-562-9468

Page 3

FCC WARNING

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.

It has been tested and found to comply with the limits for class A computing devices pursuant to subpart J of part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

POWER REQUIREMENT WARNING !

A power supply capable of supplying the following current (or greater) must be used for game conversion:

7 amps @ + 5.0 VDC 1 amp @ - 5.0 VDC 1 amp @ + 12.0 VDC

RECORD OF SERIAL NUMBERS

Record the game serial numbers and date purchased for future reference and/or game service.

Date purchased:

Main Circuit Board S/N:

Input/Output and Memory Expansion circuit board S/N:

Program part number (on EPROMs) :

Software serial number (on "attract mode" screen):

Page 4

A. UP YOUR ALLEY ~- OPERATION AND MAINTENANCE MANUAL

TABLE OF CONTENTS

SECTION

WARRANTY

HINTS FOR SUCCESSFUL GAME INSTALLATION

  • INSPECT YOUR KIT
  • THE OLD CASE OF THE BENT IC PIN
  • ATTACH THE GROUND
  • WHICH POLE IS WHICH (OBSERVING POLARITY) ?
  • MARQUEE BLUES (MARQUEE INSTALLATION)
  • RUN DIAGNOSTICS (GAME INSTALLATION SUCCESS OR FAILURE)
  • MONITOR OUTPUTS
  • HOW DO I TURN UP THE SOUND?

GAME MODULE INSTALLATION

UNIVERSAL GAME CONVERSION

BOOKKEEPING/DIAGNOSTIC FUNCTIONS

  • INVOKING DIAGNOSTICS
  • SELECTING THE DESIRED FUNCTION
  • BOOKKEEPING

a. Period And Dollar Counters

b. Setting Coins/Tokens Per Dollar

ore Example Of Setting Tokens Per Dollar

  • DIAGNOSTICS

a. Buttons And Controls Test

b. Processor Memory Test

iS. Video Alignment Screens

d. Video Memory Test iL

a1

Page 5

6.

7. TABLE OF CONTENTS, cont'd

SECTION

e. Viewing Background Screens

GAME SET-UP

a. Coins Per Credit/Credits Per Coin

b. Extra Play

Cc. Attract Mode Sound

GAME STATISTICS

DURATION GRAPHS

SYSTEM TROUBLESHOOTING GUIDE

1.

3.

4. INPUT/OUTPUT FUNCTIONS

ELECTRONICS

GENERAL KNOWLEDGE

COIN COUNTER SURGE PROTECTION CIRCUIT

CONNECTOR PINOUT CHART

Page 6

TABLE OF CONTENTS continued,

LIST OF ILLUSTRATIONS

FIGURE DESCRIPTION PAGE

1 AC/DC Power Connection 9

2 Marquee Installation 10

3 Up Your Alley Main Logic Printed 15 Circuit Assembly Drawing (Component Side)

4 Up Your Alley Memory and Input/Output 16 Expansion Printed Circuit Assembly Drawing

5 Mounting Diagram Input/Output and Expansion Board 17

6 Control Panel Bolt and Ground Braid 18

hi Coin Counter Surge Protection Circuit 36

Page 7

A. WARRANTY

Seller warrants that its printed circuit boards, monitor and power supply, when furnished with the product and parts thereof are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller's warranty of above parts is subject to the normal use and service of its product. None of the seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, seller's sole liability shall be, as mutually agreed, to replace or repair such products which are returned to seller during said warranty period provided.

CONDITIONS:

a. Seller must be promptly notified in writing upon discovery by buyer that said products are defective. b. Products must be returned prepaid to seller plant. Ce Seller's examination of said products discloses to seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

Seller is not responsible for bent pins on ICs not installed by seller's employees. In no event shall seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for this express warranty, seller disclaims all other warranties, expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and all other obligations or liabilities on seller's behalf, and it neither assumes nor authorizes any other person to assume for seller any other liabilities in connection with the sale of products manufactured by seller.

NOTICE REGARDING THE USE OF NON-SELLER REPLACEMENT PARTS:

Seller recommends the use of only seller's parts when replacing any malfunctioning component or assembly in the seller's system. For safety and reliability, seller does not recommend or authorize any substitute parts or modifications of seller's equipment. Such alterations may adversely affect game play, cause serious injury, and void your warranty. Unauthorized parts, modifications and non-seller's game conversion kits may also void FCC compliance.

To obtain repair, contact seller at 619-562-7000 between 8 AM and 5 PM Pacific Standard Time to obtain an RMA return authorization number. Affix this number to the outside of the shipping container when returning goods. Return to the above address. .

Page 8

Be HINTS FOR SUCCESSFUL GAME INSTALLATION

Page 9

HINTS FOR SUCCESSFUL GAME INSTALLATION

Take some advice from the game masters. Successful game installation can be simple if you take a minute and read the following hints. It is worth it's weight in aspirin!

i. INSPECT YOUR KIT

Inspect all received parts for shipping damage and to familiarize yourself with the parts. Inspect all integrated circuits (hereafter called "IC") for bent pins (being careful not to bend the pins).

THE OLD CASE OF THE BENT IC PIN

The #1 killer of a successful game installation, or for that matter, any other electronic device's proper operation, is bent pins. Avoid this plague and take the time (and patience) to make sure that all pins are in each hole and not bent.

Also, installing ICs with bent pins runs the risk of bending the pins even further and eventually breaking them.

If pins are bent, first, grip the group of pins lengthwise with long needle-nose pliers. This gripping action will straighten them in this direction. Next, if any pins are bent in the other direction, straighten each one individually with needle nose pliers being careful not to over-compensate. This overcompensation may break the pin.

ATTACH THE GROUND

Make sure to attach the ground braid to the control panel. Players risk an electric shock if the control panel is not properly grounded.

Refer to figure 6 for ground braid connection.

WHICH POLE IS WHICH (OBSERVING POLARITY)?

Electronic circuits are quite sensitive to polarity and can easily lose their sense of humor when the polarity is reversed. A fuse may not be all they blow! Experienced electronic engineers check the polarity two times before applying power! You should probably check it three times.

Refer to figure 1 on the next page for proper 115 VAC and DC power connections.

Page 10

FIGURE 1 AC/DC POWER CONNECTION ~ : — panne atm enn) D a GROUND BRAID |e

D/ NEUT“AL | A .

POWER CORD 2

GND +12V °

115 vac

E.M.I. FILTER

BLACK

RED RED RED

INTERLOCK

SWITCH

CONTROL PANEL Lo PLUORESCENT rene a =e _DBANGE DAonwonarnaad

YELLOW

FUSE WHITE A.POWER SUPPL +5V @ 7A -5V @ 1A +12V @ 1A BROWN I/O MEMORY EXPANSION BOARD BROWN C.MAIN LOGIC BOARD

ISOLATION TRANSFORMER D.CIRCUIT PANEL PLATE

“SEC PRI

MONITOR PIN 10 PIN 1 PococoodGG OUR PIN-OUT IS OPPOSITE OF THE PIN-OUT PRINTED ON THE CONNECTO I.E. PIN 1 IS PIN 10

IND BRAID I08 . FOR A 10 PIN CONNECTOR

Page 11

MARQUEE BLUES (MARQUEE INSTALLATION)

Your game is a money making investment! Why compromise by installing a crooked marquee? Avoid this and follow these instructions for installing:

First, place the plexiglass on a table. Next, center the decal on the plexiglass, getting an idea of the general location (before peeling off the back). Now, carefully peel off the back and place the far edge (lengthwise) on the plexiglass first, centering the remaining un-stuck (important) decal. Finally, "roll" down the rest of the decal, slowly, squeezing the air bubbles out with your hand.

Pictured is the marquee on a Cinemat System Cabinet.

Marquee Installation

FIGURE 2

Page 12

an RUN DIAGNOSTICS (GAME INSTALLATION SUCCESS OR FAILURE)

Five minutes of diagnostics may save an.hour of frustration wondering why a feature does not work. Our software department is the best in the business. They labored long and hard to write diagnostics to thoroughly check out your game. Take the time to follow the diagnostics section and prove to yourself that the entire game is working properly.

Next, play the game a couple of times to verify that all is well.

MONITOR OUTPUTS

The outputs from our system to the monitor are red, green and blue with negative horizontal and negative vertical sync.

HOW DO I TURN UP THE SOUND ?

Volume adjustment is easy. Refer to figure 3 and locate VR1 (on main circuit board). Now look at the main board (largest board). Clockwise rotation increases the volume.

Page 13

C. GAME MODULE INSTALLATION

Page 14

c. GAME MODULE INSTALLATION

1.

an Parts for the UP YOUR ALLEY game module are as follows. Please inspect and check off.

QTY DESCRIPTION

1 UP YOUR ALLEY Marquee Lexan Decal Plexiglass Marquee I/O Expansion board PROMs Custom Chip (U120) 02-13 Custom Chip Control Panel Assembly 1 1/2" Carriage Bolts #10 Flat Washers #10-24 Hex Nuts #10-24 Wing Nuts ay NNEREP PENNER

Install the 21 UP YOUR ALLEY EPROMS in the main board noting the chip location ("U" number) printed on each chip and referring to Figure 3. Match the location of pin 1 of both the EPROM and socket, plug each EPROM into the socket indicated. Be sure all EPROMS' pins are aligned and the EPROMs are pressed firmly in place.

Install the custom chip U120 in the main logic board at location U120 and the 02-13 custom chip at U85 making sure Pin 1 of the chip and Pin 1 of the socket are aligned.

Recheck steps 2 and 3 for proper parts placement and orientation.

Remove the Z-80B microprocessor from location U99 of the main logic board and reinstall it at location U13 of the I/O and Memory Expansion board. Install the I/O and Memory Expansion board ribbon cables as shown in Figure 5.

Position the UP YOUR ALLEY control panel assembly on the cabinet and attach using the 1-1/2 " carriage bolts, washers and 10-24 hex nuts provided. Install only the front-most bolt, washer, and nut on each side at this time. See Figure 6.

Page 15

Route the control panel wiring harness. Locate the three connectors labeled P5, J4 and J5 at the end of the control panel harness. Plug connector P5 located along the top edge of the main logic board. Similarly, plug J4 into J4 and J5 into J5 of the I/O and Memory Expansion board. Plug the remaining two wires (white and violet) of the control panel harness into connector P4 of the main board. Refer to Connector Pinout Chart in back of manual.

Attach the marquee to the plexiglass using the procedure in section B above.

Installation of the game module is now complete. We suggest you now use the system's "on board" diagnostics to inspect the game, See the diagnostics section of this manual.

After testing the control panel, use the remaining two carriage bolts, washers and wing nuts to secure the control panel.

Page 16

FIGURE 3 Pi PRINTED CIRCUIT ASSEMBLY

U9 UP YOR ALLY 03-14156-00 u8 UP YOR ALLY 03-14155-00 UT UP YOR ALLY 03-14154-00 a | U6 UP YOR ALLY 03-14153-00 U5 ) O4-01

UP YOR ALLY O17 03-14152-00 UP YOUR ALLEY CINEMAT MAIN LOGIC VYOLU ME VR'O contRot

COMPONENT SIDE 02-13 Bas U107 UP YOR ALLY 03-14174-00 U106 UP YOR ALL 03-14173-00

i) UP YOR ALLY 03-14172-00

U95 UP YOR ALLY 03-14167-00 ugk YOR ALLY 03-14166-00 u104 UP YOR ALLY O7-01 03-14171-00

5 08-01 Uu93 UP YOR ALLY 03-14165-00 U103 UP YOR ALLY 03-14170-00

4 > 03-01 |

u OG UP YOR ALLY 03-14151-00 U3 UP YOR ALLY 03-14150-00 oa Be JP ) 11-01 b2? ) 10-01 O26 u10e 1 UP YOR ALLY UP YOR ALLY 03-14169-00 03-14168-00

b42 09-01 b40 UTO ‘OF NOT USED RALLY 03-14164-00

u69 UP YOR ALLY 03-14159-00 u68 UP YOR ALLY 03-14158-00 OT USED

ag Hd Jp2 u90 UP YOR ALLY 03-14162-00

U67 UP YOR ALLY 03-14157-00 OR ALLY 03-14161-00 RESET P23 Swi P4

Page 17

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 18

yyy

© mwa

(9

Eom»

FIGURE 5

Mounting Diagram Input/Output and Expansion Board

Page 19

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 20

De UNIVERSAL GAME CONVERSION

Page 21

UP YOUR ALLEY ~- OPERATION AND MAINTENANCE MANUAL

D. UNIVERSAL GAME CONVERSION

  • Parts for the UP YOUR ALLEY conversion kit are as follows. Please inspect and check off:

QTY DESCRIPTION

Marquee Plexi, Clear Marquee Decal, UP YOUR ALLEY Ty-wrap w/eyelet UP YOUR ALLEY, Control Panel Assembly UP YOUR ALLEY, Circuit Board Assembly Manual, UP YOUR ALLEY Harness, Video Harness, Coin Service Harness, Speaker Harness, DC Power Side Decals, CINEMAT ° NBPPRPRPPRPRPPR

2s Remove existing game control panel, and all buttons or joystick controls associated with it. Position the universal control panel above the control panel intended for conversion. Feed the harness through a convenient hole, large enough for the harness connectors.

  • Securely mount the universal control panel with a bolt or screw not easily removed from the exterior of the cabinet. Avoid pinching the wires. Secure using the tywraps included with your kit.

\> When routing the harness, leave enough slack so that servicing of the control panel and circuit board assembly can be accomplished with relative ease. Place a wire ty-wrap as close to the circuit board connectors as possible, to relieve strain on the connector pins.

  • Mount the circuit board in an area of the cabinet that receives ample ventilation. Make sure the circuit board can be removed easily for service.

Refer to the D.C. power wiring diagram, making all the power connections as shown. Be sure to hook up the ground braid. Also, observe proper polarity. Careful with this one,

  • The last order of business is the Marquee and Plexiglass. See section B above for this procedure.
  • The conversion process is now complete. It is recommended at this point, to go into diagnostics to test the performance of the new kit.
Page 22

E. BOOKKEEPING/DIAGNOSTICS FUNCTIONS

Page 23

|F BOOKKEEPING / DIAGNOSTIC FUNCTIONS

UP YOUR ALLEY has extensive bookkeeping and diagnostic functions. These functions are explained in the following section:

  • INVOKING DIAGNOSTICS

With the game running in the attract mode follow these steps:

a. Press and hold the one player start button while pressing and releasing the service button (found inside the coin door mounted to the top of the coin box). Concerning kits, connect the appropriate pins to ground referring to the Connector Pinout Chart in the back of the manual.

b. Release the player one-player start button.

Cie The game screen should now appear as shown below. Instructions for selecting and entering the listed functions are displayed at the top of the screen with the five selectable options below them. The game's software version number is shown in the lower left-hand corner of the screen.

  • SELECTING THE DESIRED FUNCTION

The one-player start button selects the desired function. The function has been selected when the display color for that particular function changes. Pressing the two player start button enters the selected function. Selecting the RESTART THE GAME function returns the game to normal operation.

An example of the display is as follows:

MAIN MENU

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

BOOKKEEPING DIAGNOSTICS GAME SET-UP GAME STATISTICS GAME DURATION GRAPHS ERASE ALL PLAYER STATISTICS

RESTART THE GAME CANCEL CHANGES AND RESTART GAME S/N xxxxxx

Page 24

BOOKKEEPING

The bookkeeping screen is displayed when that option is selected and entered from the main menu. Five lifetime counters are shown. These counters are set to zero at the factory and are not resetable by the operator. The counters are:

COINS DROPPED MECH 1 - This counter shows the total number of coins that have dropped through the LEFT coin mech.

COINS DROPPED MECH 2 - This counter shows the total number of coins that have dropped through the RIGHT coin mech.

TOTAL COINS DROPPED - This is the total number of coins dropped through BOTH mechs.

SERVICE BUTTON PRESSED - The number of times that the service button has been pressed. Pressing the service button to enter the bookkeeping/diagnostic section does not affect this counter.

TOTAL CREDITS GIVEN - The total number of credits the game has given in it's lifetime is shown on this counter. See the game set-up section of this manual for information on setting the number of coins per credit.

a. PERIOD AND DOLLAR COUNTERS

Three resetable counters, located to the right of the lifetime counters are provided to aid the operator in tracking the games intake over a period of time. These counters are:

ae coins dropped

  • dollars collected

As in the main menu, these options are selected by pressing the one-player start button and entered by pressing the two player start button. To reset the period and dollar counters for either coin mech, press the one-player start button until the message “RESET COIN MECH 1 (or 2) DOLLARS COLLECTED" changes color. Then press the two-player start button,

Page 25

SETTING COINS/TOKENS PER DOLLAR

To calculate dollars collected the bookkeeping system needs to know how many coins/tokens are required to make a dollar. Normally, this number would be 4 for quarter operation. If you operate a location where for example 6 tokens equal one dollar, the dollar multiplier should be changed to 6 so that the dollars collected counters will reflect accurately what the game has earned.

To change the coin "multiplier" use the player one start button to highlight the COINS PER DOLLAR message for the desired coin mech then use the player two start button to change the multiplier.

EXAMPLE OF SETTING TOKENS PER DOLLAR

An arcade giving 10 tokens per dollar should have the coins/tokens per dollar multipliers set as shown.

An example of the display is as follows:

10 COINS PER DOLLAR COIN MECH 1 10 COINS PER DOLLAR COIN MECH 2

NOTE: THE COINS PER DOLLAR MULTIPLIER DOES NOT AFFECT THE NUMBER OF COINS PER CREDIT OR CREDITS PER COIN. SEE THE GAME SET-UP OPTIONS SECTION OF THIS MANUAL FOR THAT INFORMATION.
Page 26

BOOKKEEPING

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

COINS DROPPED - MECH 1 LIFETIME: PERIOD COINS: PERIOD DOLLARS: ooo

COINS DROPPED - MECH 2 LIFETIME: PERIOD COINS: PERIOD DOLLARS: ooo

TOTAL COINS DROPPED LIFETIME: PERIOD COINS: PERIOD DOLLARS: ooo

SERVICE BUTTON PRESSED TOTAL CREDITS GIVEN

RESET COIN MECH COUNTERS RESET MECH 1 DOLLARS COLLECTED RESET MECH 2 DOLLARS COLLECTED

SET COINS/TOKENS PER DOLLAR 4 COINS PER DOLLAR COIN MECH 1 4 COINS PER DOLLAR COIN MECH 2

RETURN TO MAIN MENU

DIAGNOSTICS

The diagnostic menu is displayed upon entering diagnostics from the main menu. The player can then select the desired function.

DIAGNOSTICS

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

BUTTONS AND CONTROL TEST PROCESSOR MEMORY TEST VIDEO ALIGNMENT SCREENS VIDEO MEMORY TEST BACKGROUND AND SCROLLING

RETURN TO MAIN MENU

Page 27

BUTTONS AND CONTROLS TEST

This test allows the operator to check the game controls and switches. Pressing a button or activating a control causes the description of that button or control to change color on the video screen,

The word GOOD will appear to the right of the control's description when the switch contacts close and will remain on the screen until the button is released.

Pressing the player two start or service buttons twice will end the test and return you to the diagnostic menu.

An example of the display is as follows:

PLEASE PRESS THE FOLLOWING BUTTONS:

1 PLAYER START 2 PLAYER START MECH 1 COIN BUTTON MECH 2 COIN BUTTON SERVICE SWITCH MAN LEFT BUTTON MAN RIGHT BUTTON ARROW RIGHT BUTTON ARROW LEFT BUTTON

SPEED JOYSTICK:

HOOK JOYSTICK:

PRESS THE PLAYER 2 OR SERVICE BUTTON TWICE TO EXIT

PROCESSOR MEMORY TEST

The processor memory test checks all on-board RAM and PROM memory with the exception of the video memory. The messages TESTING MASTER ROM, TESTING MASTER RAM, TESTING COLOR RAM, TESTING SLAVE PROM, TESTING SLAVE RAM will each appear on the left side of the screen as each of those tests are performed. The result of each test (pass or fail) is displayed on the left side of the screen under the description of that test.

Two error messages may appear during slave memory test, those are COMMUNICATION ERROR and SLAVE NOT RESPONDING. ICs to be checked, in order of priority, are listed below:

Page 28

UP YOUR ALLEY ~- OPERATION AND MAINTENANCE MANUAL

COMMUNICATION ERROR — a. U19 b. U21 THROUGH U23 c. U45 d. U60 e. U62 £. U64

SLAVE NOT RESPONDING - a. U10 (slave RAM) b. U3 (EPROM) c. Ul (280 CPU) d. U2 e. U20, U18 f£. U61, U63

In the case of a failure of a ROM or RAM, the location (U number) of the suspected part is shown on the screen,

The following is an example of the display indicating a U4 failure.

PROCESSOR MEMORY TEST

MASTER ROM TESTED MASTER ROM GOOD

MASTER RAM TESTED MASTER RAM GOOD

COLOR RAM TESTED COLOR RAM GOOD

SLAVE MEMORY TESTED

SLAVE ROM BAD CHIP U4 SUSPECT SLAVE RAM GOOD

PLAYER 2 START EXITS TESTING

VIDEO ALIGNMENT SCREENS

Three video alignment screens are provided to aid in adjusting the game's video monitor for maximum picture quality. Refer to the video monitor technical manual (not supplied) for technical information and adjustment instructions.

The first screen consists of a white crosshatch pattern. This should be used to adjust screen position, horizontal size, vertical size and focus. Pressing the player two start button advances the display to the next alignment screen.

Page 29

\= The second alignment screen is used to adjust the red and green intensity. An eight level (0-7) color scale is shown for each red and green. The monitor should be adjusted so that level zero is black and one through seven appear as seven distinct levels.

The third alignment screen shows a four level blue color scale. Adjust the blue intensity so that level zero is black and levels one through three show as three distinct levels of blue. Eight other colors are also displayed for reference, they are from 0-7: blue, green, red, cyan, magenta, yellow, gray and white.

VIDEO MEMORY TEST

The video memory test checks the foreground video memory. The test appears as a series of colored bars moving across the screen, After each pass {about 15 seconds) the results of the test will be displayed on the screen.

If the pass was successful (all RAMs good) the message "VIDEO RAM CHECKS OK" will be displayed for about 5 seconds and the test will be repeated. Pressing the two player start button anytime during the test will abort the test and return you to the diagnostic menu.

If the memory test fails, the message "VIDEO RAM TEST FAILED" will be displayed along with the location (U number) of the suspect RAM. In the event that the video error display is unreadable, a series of tones will also indicate the suspect chip (see table below).

NUMBER OF AUDIBLE BEEPS SUSPECT ics

2 U35 and U36 4 U33 and U34 6 u48 and U49 8 U46 and U47

VIEWING BACKGROUND SCREENS AND BACKGROUND TEST

This test is set up to view all the background screens by pressing the one-player start button to advance the screens, Pressing the two-player start button exits the program.

An example of the display is as follows:

Page 30

BACKGROUND PROM TEST

NOW VIEWING PROM U69

PRESS 1 PLAYER START TO ADVANCE, OR 2 PLAYER START TO EXIT.

  • GAME SET-UP

The game option set-up section allows the operator to change various game options. As explained in previous sections, the one player start button selects and highlights the desired function and the two player start button enters or executes the function

a. COINS PER CREDIT / CREDITS PER COIN

The coinage of each mech may be set to require multiple coins for each credit or give multiple credits for each coin.

To change coinage, follow the examples below: (all examples assume 1 coin=25 cents

For 25 cent play: 1 COIN FOR 1 CREDIT

For 50 cent play: 2 COINS FOR 1 CREDIT

Two plays for 25 cents: 1 COIN FOR 2 CREDITS

fom EXTRA PLAY

An option is included to award an extra play for the insertion of multiple coins before the game is started.

For example; if the coinage is set as follows:

1 COIN FOR 1 CREDIT EXTRA PLAY FOR 2 CREDITS

then the result will be, 1 coin will give 1 credit and 2 coins will give 3 credits. Each additional coin will add one credit.

¢. ATTRACT MODE SOUND

This option when selected enables the game sounds during the attract mode.

Page 31

An example of the display is as follows:

GAME SET-UP

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

COIN MECH 1 1 COIN FOR 1 CREDIT NO EXTRA PLAY

COIN MECH 2 1 COIN FOR 1 CREDIT NO EXTRA PLAY

TWO PLAYER FOR 1 CREDIT ATTRACT MODE SOUND. ALLOW BEER FRAMES

BOWL FOR FREE 2 PLAYER GAME SHOW LANE DOTS

RETURN TO MAIN MENU

GAME STATISTICS NO YES YES YES YES YES

Game statistics are provided to aid the operator in setting up his game for

The operator may reset the game statistic counters by maximum profit.

selecting the "reset game statistics" function,

GAME STATISTICS

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

NUMBER OF 1 PLAYER GAMES: 0

NUMBER OF 2 PLAYER GAMES: 0

COMPLETE GAMES BOUGHT: 0

AVERAGE SCORE: 0

RESET GAME STATISTICS RETURN TO MAIN MENU

Page 32
  • DURATION GRAPHS

Graphs are provided which indicate the duration of one and two player games. Average play time is also displayed. These graphs may be reset by selecting the reset options located at the bottom of the screen,

An example of the display is as follows:

DURATION GRAPHS

SELECT FUNCTION WITH ONE PLAYER START BUTTON ENTER FUNCTION WITH TWO PLAYER START BUTTON

ONE PLAYER GAME TIMES 0:00-2:00

5:31-6:00 6:01-UP

TWO PLAYER GAME TIMES

10:01-10:30 10:31-11:00 11:01-11:30 11:31-12:00 12:01-UP

PLAYER ONE AVERAGE TIME: PLAYER TWO AVERAGE TIME:

PLAYER ONE TOTAL GAMES: PLAYER TWO TOTAL GAMES:

RESET 1 PLAYER BAR GRAPHS RESET 2 PLAYER BAR GRAPHS RETURN TO MAIN MENU

Page 33

SYSTEM TROUBLESHOOTING GUIDE

The entire Cinemat game system can be broken down into major groups. A brief guide to troubleshooting each section follows:

  • INPUT/OUTPUT FUNCTIONS:

a. Monitor

  • No raster (i.e. black screen)

a.

be Check AC supply to monitor. If there is no power at the monitor, trace the wiring back to the isolation transformer and/or verify that power is reaching the transformer,

Check monitor fuses.

  • Display scrolls (apparent syncronization problem).

a.

b. Check monitor alignment adjustments.

Check RGB and syncronization signals on PCB connector and trace through to the monitor.

  • Black screen

a.

b. Check for +5.0 VDC at circuit boards.

Check connectors are securely seated and in the proper position.

4, White or checkerboard screen.

a. Check for +5.0 VDC on P4 ~ 3 through 7. If any of these signals are low, replace uil4 (74LS08). If this fails, replace U119 (74LS257).

Check the clock signal on the master Z80 (U99-6), BASEBALL, THE SEASON II I/O and Memory Expansion Board (U13), REDLINE RACER Sound Board (U14).

Check reset on the 280 (U99-26). This signal should normally be high and go low when the reset button is pressed.

Page 34
  • White or red vertical lines close together on entire screen or half of screen.

a. Check video RAMs U33 through U36 and U46 through U49. Refer to sheet 11 and 18 on schematic.

  • Vertical lines on background.

a. Check signals on U81 through U83 (74LS8166's).

b. Regarding other background problems, check the position of JP2 Jumpers, swap U56, (74LS461) with U60, see if problem disappears.

  • White vertical bars, usually on half of screen sometimes with an audio buzz.

a. Caused by excessive temperature. Swap U45 with U23 and/or U60 with U22 (74LS461's).

  • Intermittent flashing video or color changes.

a. Check for +5.0 VDC at circuit boards, TP1 and TP2 (+5 VDC)

  • Picture freezes.

a. Check for +5.0 VDC at circuit boards, TP1 and TP2 (+5 VDC)

b. Check 280s (U1 and U99). They should be Zilog Mostek devices with a "B" suffix (6 MHz). If not call for replacement.

Ce Check for damaged sockets on master EPROMs and master CPU.

  • Drifting pattern (any color).

a. Check connector and signals on Pl.

b. Sign of synchronization problems. Check DCLK,

c. Check u40 (RGSO9), U42 (RGSO7), and U43 (RGSO8).

be Buttons, joysticks and coin counters.

  • A careful visual inspection of the buttons harnesses and connectors is advised.

a. Inspect harness crimps.

Page 35

be Check for broken wires.

c. Check for broken solder joints at the termination point.

  • Trace signals through back to the input IC on the PCB.
  • Electronics

a. Main board electronics.

  • Problems can sometimes be traced to a bad CPU or crystal. Check the master and slave CPU's and their associated components.
  • Check EPROMs for background and foreground display and the associated video timing logic.

ot Check power at the ICs.

Add on board(s) that control game specific functions.

Te Again, check for functions specific to the board.

  • Check all ICs for proper socket installation
  • Check power at the ICs.
  • General Knowledge

1. Proper voltage input jumpering on the board is critical! Follow the instructions on this carefully. A symptom of improper jumpering is an audio buzz or no audio. Check for 12.0 to 15.0 VDC at U122-5 (audio amp). Refer to Power Supply Modification section of manual. NOTE: If your speaker is not connected, you will not hear any sound! Seriously, try adjusting the audio volume control pot (VP1). See section B-7 above on adjusting the volume.

Game powers up with garbage on the screen - no buttons function - audio may buzz

a. Remove P4 and P5 and reset system (push button on main board). If picture appears, the problem may be a stuck coin switch, button or bad harness or ground connection.

b. Visually inspect connector crimps and wire colors,

Cc. Check for + 5.0 VDC at board.

Page 36

A word about coin counters:

Do not use. mechanical coin counters in any kit or dedicated game. These devices produce an inductive "kick" that will damage components on the circuit board(s). Problems caused by this are checkerboard video. A quick check to see if this is your problem is look at the "NMI not" signal on both Z80s (pin 17). If a low output is observed, try replacing U114 (74LS08) or if needed, U119 (74L8157) .

The bookkeeping on our games is very accurate and includes number of coins dropped and dollars earned,

If you must install a coin counter, the next page shows a simple hookup using diode protection.

Page 37

COIN COUNTER SURGE PROTECTION CIRCUIT

  • IF YOU MUST INSTALL A COIN COUNTER

COIN SWITCH

COIN COUNTER

oR >} tN.

DIODE MAY BE 1N4001 THROUGH 1N4003

FIGURE 7

Page 38

UP YOUR ALLEY, CONNECTOR PINOUT CHART

FROM CONNECTOR PIN # SIGNAL DESCRIPTION TO CONNECTOR PIN # WIRE COLOR

MAIN LOGIC BOARD CONNECTORS:

P1-1 NOT USED

P1-2MONITOR, -H SYNCGRAY
P1-3MONITOR, -V SYNCWHITE

P1i-4 MONITOR, GROUND BLACK

PI=5.MONITOR, REDRED

P1-6 POLARIZING KEY

P1-7MONITOR, GREENGREEN

P1-8 NOT USED

P1-9MONITOR, BLUEBLUE

P1-10 NOT USED

P2-1SPEAKER GROUNDSPEAKERGRAY
P2-2SPEAKER GROUNDSPEAKERWHITE
P3-1+5 VOLTSJ2-1RED
P3-2+5 VOLTSJ2-2RED
P3-3+5 VOLTSJ2-3RED
P3-4POLARIZING KEYJ2-4

P3-5 GROUND J2-5 BLACK

P3-6 GROUND J2-6 BLACK

P3-7 GROUND J2-7 BLACK

P3-8GROUNDJ2-8BLACK
P3-9J2-9BROWN
P3-10+12 OR 25 VOLTSJ2-10ORANGE

P4-1 NOT USED 7

P4-2GND, COIN, SERVICECOIN DOORBLACK OR GREEN
P4-3TWO PLAYER STARTCONTROL PANELVIOLET
Pp4-4NORMALLY OPENCOIN SWITCH 2ORANGE
P4-5NORMALLY OPENSERVICE SWITCHYELLOW
P4-6ONE PLAYER STARTCONTROL PANELWHITE
P4-7NORMALLY OPENCOIN SWITCH 1BLUE

P4-8 NOT USED P4-9 NOT USED P4-10 NOT USED

P5-1 NOT USED

P5-2GROUNDCONTROL PANELGREEN
P5-3POINTER LEFT (N.O.)CONTROL PANELBLUE
P5-4POINTER RIGHT (N.O.)CONTROL PANELGRAY
P5-5BOWLER RIGHT (N.0.)CONTROL PANELYELLOW
P5-6BOWLER LEFT (N.0.)CONTROL PANELBROWN

P5-7 NOT USED P5-8 NOT USED P5-9 NOT USED P5-10

P6 NOT USED XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Page 39

UP YOUR ALLEY, CONNECTOR PINOUT CHART

FROM TO

CONNECTOR SIGNALCONNECTORWIRE
PIN #DESCRIPTIONPIN #COLOR

INPUT/OUTPUT AND MEMORY EXPANSION BOARD CONNECTORS:

Ji-1+5 VOLTSPOWER SUPPLYRED
J1-2+5 VOLTSPOWER SUPPLYRED
J1-3+5 VOLTSPOWER SUPPLYRED

J1-4 POLARIZING KEY

g1-5GROUNDPOWER SUPPLYBLACK

J1-6 GROUND POWER SUPPLY BLACK

g1-7GROUNDPOWER SUPPLYBLACK
J1-8GROUNDPOWER SUPPLYBLACK

J1-9 NOT USED

g1-10+12 OR +25 VOLTSPOWER SUPPLYORANGE
J2-1+5 VOLTSP3-1 (MAINRED
J2-2+5 VOLTSP3-2 LOGICRED
J2-3+5 VOLTSP3-3 BOARD)RED
J2-4POLARIZING KEYP3-4

J2-5 GROUND P3-5 BLACK

J2-6 GROUND P3-6 BLACK

d2-7GROUNDP3-7BLACK
J2-8GROUNDP3-8BLACK
J2-9P3-9BROWN
J2-10+12 OR +25 VOLTSP3-10ORANGE

J3 NOT USED

J4-1 GROUND JOYSTICK GREEN

J4-2+12 VOLTSJOYSTICKORANGE

J4-3 NOT USED

J4-4HOOKJOYSTICKBLUE
J4-5BALL SPEEDJOYSTICKVIOLET

J4-6 NOT USED J4-7 NOT USED J4-8 NOT USED J4-9 NOT USED g4-10 NOT USED g4-11 POLARIZING KEY J4-12 NOT USED

J5-1GROUNDTAG PCB J1-2GREEN
J5-2DATA LINE 13TAG PCB J1-7BROWN
J5-3+5 VOLTSTAG PCB J1-1RED
J5-4CLOCKTAG PCB J1-5BLACK
J5-5RES 3TAG PCB J1-4VIOLET
J5-6RES 2TAG PCB J1-3ORANGE
J5-7DATA LINE 12TAG PCB J1-6GRAY
J5-8DATA LINE 3TAG PCB J1-10YELLOW
J5-9DATA LINE 2TAG PCB J1-9BLUE

J5-10 POLARIZING KEY

J5-11SPARETAG PCB J1-8WHITE

J5-12 NOT USED

Page 40

UP YOUR ALLEY, CONNECTOR PINOUT CHART

FROM TO CONNECTOR SIGNAL CONNECTOR WIRE

PIN #DESCRIPTIONPIN #COLOR

J6 NOT USED XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

INPUT/OUTPUT AND MEMORY EXPANSION BOARD 40 PIN RIBBON CABLE CONNECTOR:

J7A-1MASTER ADDRESS LINE 11u99-1 (MAIN
J7A-2MASTER ADDRESS LINE 12ug99-2 LOGIC
J7A-3MASTER ADDRESS LINE 13u99-3 BOARD)
J7TA-4MASTER ADDRESS LINE 14ug99-4
J7A-5MASTER ADDRESS LINE 15U99-5
J7TA-6CLOCKU99-6
JTA-7MASTER DATA LINE 4uU99-7
J7A-8MASTER DATA LINE 3u99-8
JTA-9MASTER DATA LINE 5u99-9
J7A-10MASTER DATA LINE 6u99-10
J7A-11+5 VOLTSug99-11
J7A-12MASTER DATA LINE 2u99-12
J7A-13MASTER DATA LINE 7ug99-13
J7A-14MASTER DATA LINE 0ug9-14
JTA-15MASTER DATA LINE 1u99-15
J7A-16INTu99-16
JTA-17MNMIU99-17
J7A-18NOT USEDuU99-18
J7A-19MREQug99-19
J7A-20I/O REQug99-20
STA-21RDug99-21
J7TA-22WRU99-22
J7A-23NOT USEDU99-23
JTA-24WAITU99-24
J7A-25+5 VOLTSug99-25
JTA-26PORUu99-26
J7A-27M1U99-27
J7A-28RFSHuU99-28
JTA-29GROUNDug99-29
J7A-30MASTER ADDRESS LINE 0u99-30
J7A-31MASTER ADDRESS LINE 1u99-31
J7A-32MASTER ADDRESS LINE 2ug99-32
J7TA-33MASTER ADDRESS LINE 3U99-33
JTA-34MASTER ADDRESS LINE 4u99-34
J7A-35MASTER ADDRESS LINE 5u99-35
J7A-36MASTER ADDRESS LINE 6U99-36
J7A-37MASTER ADDRESS LINE 7U99-37
JTA-38MASTER ADDRESS LINE 8u99-38
JTA-39MASTER ADDRESS LINE 9ug99-39
J7A-40MASTER ADDRESS LINE 10u99-40

J7B NOT USED

Page 41

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 42

Cinematronics— The Leland Corporation 1841 Friendship Drive, El Cajon, CA 92020 © (619) 562-7000

  • indicates registered trademarks of Cinematronics © 1987 Cinematronics