Skull and Crossbones TM-342 1st Printing Kit
Skull & Crossbones (rev 5) (Atari Games, 1989) · Kit Manual · 54 pages · 72 sections · original scan
4st printing
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
A
ATARI
GAMES
Skull & Crossbones:
Universal Kit
Installation Instructions
with Parts Mustrations and Schematic Diagrams
© 1989 by Atari Games Corporation. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035
ie Printed in the U.S.A 11/89
Produced by the Atari Games Technical Publications Department.
Editing and Text Layout: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner Skull & Crossbones Universal Kit
Notice Regarding
Non-Atari® Parts
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game.
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
Note
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram. ¢ The power cord is properly plugged into a grounded three wire outlet.
- On games provided with an Electromagnetic Interference (EMI) ground cage, be sure that the printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Skull & Crossbones Universal Kit
Table of Contents List of Illustrations
1 Installation Figure 1-1 Installing the Kit Parts ...... How to Use This Manual .. 11 Equipment Requirements .. 1-2 Figure 2-1 RAM Error Message... Tools Required ..... 12 Figure 2-2 ROM Error Message. Preparing the Existing Game for Conversion ... 1-2 Figure 2-3 Switch Test Screen Inspecting the Kit ... 1-2 Figure 2-4 Coin Options Screen. Installing the Kit Parts 13 Figure 2-5 Game Options Screen.. Testing After Power-Up 17 Figure 2-6 First Statistics Screen 2-4 Setting the Coin and Game Options .. 1-7 Figure 2-7 Second Statistics Scree: 2-5 Game Play ... 17 Figure 2-8 Playfield Scrolling Test. 2-5 Figure 2-9 Motion Object Test. . Figure 2-10 Alphanumerics Test .. = Figure 2-11 Color Test... 2 ark Figure 2-12 Color Purity Test ee ’ Figure 2-13 Convergence Tes! Statistics and Histogram Screens 33 Figure 2-14 Sound Test... 24 Figure 3-1 Opening the Control Panel 25 Figure 3-2 Maintaining the Joystick . 25 Figure 3-3. Removing the Video Display Sound Board Test Switch Test... Complete RAM Test Plato daa 23 Figure 4-1 Cabinet-Mounted Assemblies, Front View..4-2 Motion Object Test . 26 Figure 4-3 Control Panel Assembly. Alphanumeric Tes! 26 Figure 44 Joystick Assembly ..... Color Test...... Figure 4-5 Coin Cointrols, Inc. Coin Door Color Purity Test . Assembly Convergence Test Figure 4-6 Power Supply Assembly . Figure 47 Cyberball 2072 Game PCB 3 Maintenance Figure 4-8 JSA Audio II PCB Assembly........
List of Tables Maintaining the Joystick Troubleshooting. Disassembling vyst Reassembling the Joystick .. Table 1-1 Game Specifications 4 Illustrated Parts Lists Table 2-1 RAM Error Locations Table 2-2. ROM Error Locations. 2-2 5 Schematic Diagrams Table 2-3 Coin Option Settings Table 2-4 —_- Regions... Skull & Crossbones Statistics Sheet Table 2-5 Game Option Settings
- Table 2-6 Faulty Sound RAM and ROM Warranty
Table 3-1 Maintenance and Inspection Items. Table 3-2 Troubleshiooting Table Table 3-3 Voltage Inputs and Test Points on
Table 3-4 © What ROM Problems Look Lik
Skull & Crossbones Universal Kit
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific wamings and cautions will be found in this manual whenever they apply.
ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:
Chapter 1
Installation
How to Use This Manual
This manual provides information for installing, testing, and troubleshooting the Skull & Crossbones universal kit. The manual is divided into the following chapters: @ Chapter 1 describes the installation proce- Also bound into Chapter 1 of this manual is the temdure and the Skull & Crossbones game play. plate for drilling the holes into the Skull & Crossbones ™ Chapter 2 contains self-test procedures. m Chapter 3 control panel. contains troubleshooting procedures. @ Chapter 4 contains illustrated parts lists. @ Chapter 5 contains the schematics for the game PCB and the JSA Audio II PCB.
Installation
Equipment Requirements
See Table 1-1 for the equipment required in the cabinet in which you are installing the Skull & Crossbones kit.
Table 1-1 Equipment Requirements for the Skull & Crossbones Game"
1-2 Skull & Crossbones Universal Kit
Tools Required
m Two C-clamps = Drill with 1/4 inch drill bit, a 1 3/16-inch hole cutter (or 1 3/16-inch chassis punch), and a 1 3/4-inch hole cutter Phillips screwdriver Flat-blade screwdriver Socket set Wire cutters and strippers Straightedge Squeegee X-ACTO™ knife Fast-ons (if you are installing a new JAMMA harness)
Preparing the Existing
Game for Conversion
- Turn off power to the game.
- Remove the old game PCB(s). Remove the game harness if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)-compatible. 3, Remove all the control panel decals, labels, and controls.
- Remove any side decals from the cabinet. If your cabinet has wood grain or laminate sides, remove the old graphics and adhesive. If the sides are damaged, repair them before putting on the new decals.
- Remove and clean the video display plexiglass, display bezel, attraction shield, and marquee, if any.
- Paint the cabinet, if required.
- Wipe down and vacuum the cabinet as necessary, including the face of the display.
Inspecting the Kit
Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, please contact your distributor with the Skull & Crossbones kit serial number, part number and description of any missing or damaged parts, and date received.
Skull & Crossbones Universal Kit
Installing the Kit Parts
Display Bezel Find the display bezel (part no. 047451-01). Measure the size of the existing display bezel and cut the new display bezel to size, if necessary. (See Figure 1-1.)
Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet. Side Decals Find the side panel decals (part no. 047053-01). Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as desired. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.
Attraction Shield Find the attraction shield (part no. 047205-01) and the attraction film (part no. 047452-01). Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1.
Attraction Shield
Display Bezel
Display Shield a ee
‘Blue Button Assy
Labels (6 places) Control panel in closed position Attraction Flim
Video Display Side Panel Decal
Fe, ‘Self-Test Label
Game PCB
X-Rec Screw JSA Audio W Board
Volume Contro!
‘Self-Test Switch
Right Coin Decal
Figure 1-1 Installing the Skull & Crossbones Game Parts
Installation
Table 1-2 Kit Contents Checklist
Control Panel Unpack the Skull & Crossbones Game control panel cover (part no. 047209-01) and control panel decal (part no. 047453-01). Measure your control panel to find out what size the decal and cover should be. Cut the control panel decal and cover to fit.
Driling Holes in the Control Panel Cover
- Clamp the control panel cover to the control panel. 2.
1-4 Drill four corner holes through the control panel and the control panel cover. Use a 1/4-inch drill bit. . Install four carriage bolts and locknuts through the holes to hold the cover and the control panel together, . Cut the control panel template out of the manual (see the end of this chapter). Make an actual-size copy of it. . Tape the two templates next to each other on the control panel cover. See Figure 1-2 for the controls arrangement. . Cut the holes in the cover and panel as shown by the templates using a 1 3/16-inch hole cutter for the button holes and a 1 3/4-inch hole cutter for Skull & Crossbones Universal Kit
the joystick knob holes. Use a 1/4-inch drill bit to drill the mounting holes for the joysticks. Installing the Control! Panel Decal and Labels
- Disassemble the control panel and the control panel cover. Deburr the holes in the cover and the panel.
- Install the control panel decal on the control panel. Using a sharp knife, cut out the holes for the controls in the decal.
- Put the control labels on the control panel. (See Figure 1-2.)
- Install the cover on the control panel with four carriage bolts and locknuts. Installing the Controls 1, Install the black player control buttons on the left player and the white player control buttons on the right. (See Figure 1-2.)
Joysticn Assembly (2 places)
Bie Sutton Control Panel (places)
Red Button
{8 places)
‘
Control Function Label ‘(6 places) Figure 1-2 Assembling the Control Panel and Cover
Skull & Crossbones Universal Kit
- Mount each joystick assembly on the control panel with four carriage bolts and locknuts. Install the joysticks so the Atari Games logos are upright. See Figure 1-2.
- Install the joystick harnesses on each joystick.
General Harness Installation
- If your game does not already have a JAMMA harness, find the JAMMA harness (part no. A046501-
- in the kit and install it.
- Using Table 1-3, JAMMA Pin and Wire Connections, for wiring information, connect the JAMMA harness to existing component harnessing. You can do this using crimp splices or by butt soldering.
Connecting Power Wires
- Connect the wires on the JAMMA harness to the wires for the power supply. You need +5V, -5V, and +12V for the Skull & Crossbones Game. This kit may not require all of the voltages used in your original game. Tie off any unused wires on the power supply.
- You will notice that there is more than one wire for each voltage. You must use more than one wire, as called out in the footnotes of Table 1-3. Using more than one wire for each voltage ensures that you do not overload the edge connector and cause it to burn.
Connecting Video Display Wires Connect the wires designated for the RED, GREEN, and BLUE video guns along with the sync and ground wires.
Connecting Coin Door Wires
- Connect the wires on the JAMMA harness to the coin switches and meter.
- Connect one side of the door lamps to one of the BK/W wires. Connect the other side of the door Installation
lamps to the R wire supplying +5V to the joysticks.
(Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both sides of the lamps to the terminals on the power supply.)
- Be sure to clean the coin mechanisms; however, do not lubricate the coin mechanisms.
Connecting the Control Wires Connect the joystick ‘wires to the JAMMA hamess according to the information in Table 1-3. The test screen is in the game self-test, explained in Chapter 2,
Grounding the Cabinet
Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, control panel, video display, and power supply. This is a safety requirement Sor the players’ protection. This AC ground must be of #18 AWG wire or larger.
Checking the Cabinet Systems
Before plugging in the game PCB, tum on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and -5 Volts on pins E and 5. Check that the video display and the attraction lamp have power.. The above voltages should be measured, using a voltmeter, with respect to pin 1 (BN wire) and ground. Now turn off the power to the game.
/ARNING Always power down before installing or removing the game or JSA Audio II board. Components on these PCBs are very sensitive to power spikes. Removal or installation while the power is on can damage your game board.
Installation ‘Skull & Crossbones Universal Kit
Table 1-3 JAMMA Pin and Wire Connections Solder Side Component Side
| Signal | Note | Wire | Pin | Wire | — Note | Signal |
(See Below) Color Color (See Below)
| +V RIN | 1 | BN | BN | 1 | +V RIN |
| +V RIN | 1 | BN | BN | 1 | +V RIN |
| +5V | 2 | R | R | 2 | +5V |
| +5V | 2 | R/W | Rw | 2 | +5V |
| -5V | 3 | OR | OR | 3 | sv |
| +12V | 4 | Y | Y | 4 | +12V |
Key Key SPKR- iP OW BN 1P SPKR +
| COINCIR2 | 5 | viw | BU/W | 5 | COIN CTR 1 |
NOT USED
AUDIO GND NOT USED
GREEN “6 GN R 6 RED
SYNC 6 BN BU 6 BLUE
| SERVICESW | NC | GY | BK | 6 | VIDEO RIN |
NOT USED
Right Player Left Player
| COIN 2 | 8 | BK/OR | BK/Y | 8 | COIN 1 | |
| CREDIT 2 | 9,11 | ¥/BK | W/BK | 9,11 | CREDIT1 | |
| UP2 | 9 | ¥/BN | ‘W/BN | 9 | UP | |
| DOWN 2 | 9 | ¥/R | wR | 9 | DOWN 1 | |
| LEFT 2 | 9 | ¥/OR | W/OR | 9 | LEFT 1 | c |
| RIGHT 2 | 9 | Y/w | wy | 9 | RIGHT 1 | . |
| SWORD 2 | 9 | Y/GN | W/GN | 9 | SWORD 1 | |
| TURN 2 | 9 | Y/GN | W/BU | 9 | TURN 1 | |
| sWITCHC2 | NC | Y¥/V | wiv | NC | SWITCH C1 | |
| LT/RT 2 | NG | ¥/GY | ¥/GY | NC | LT/RT1 | i |
| UP/DN2 | NC | GY/W | v | NC | UP/DN 1 | |
| GND | 10 | -BK/W | BK/W | 10 | GND | |
| GND | 10 | ~BK/W | BK/W | 10 | GND |
: Connect to the negative
; Connect both wires to the +12V terminal
- ply. (f your coin counter(s) requires) Dv, one of these twe
for the + side me Poin side of the coin couater(s) your
- counter(s) require 5V, you will need to splice into the red veh erie ye 2, above Noe Do not use e 2 24V counters.
Skull & Crossbones Universal Kit
Installing the Skull & Crossbones Printed-Circuit Boards
- Find the Skull & Crossbones Game PCB Assembly (part no. A046903-01) and JSA Audio II PCB Assembly (part no. A047184-02) and install them inside the cabinet. Use the nylon standoffs in the kit.
- Connect the JAMMA connector to the PCB.
- Apply power to the game. Check that the game PCB functions. If a video picture is not present, refer to Chapter 3.
Testing After Power-Up
Use the self-test to check the operation of the game. Refer to Chapter 2 for information about the self-tests. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure.
Setting the Coin and Game Options
The Skull & Crossbones coin and game options are set during the self-test. See Chapter 2 for information about the option settings.
Game Play
This section of the manual describes the theme of the Skull & Crossbones game and the game play features.
Introduction Skull & Crossbones is a swashbuckling adventure in which players portray two pirates competing for food, drink, booty, and revenge. Players use a joystick and button to control the unique swordfighting action. Playing the Game The game begins with an encounter with the evil Wizard, who robs our heroes of all of their booty. The pirates swear revenge and set off on a quest to destroy the Wizard and recover their treasure. The adventure takes them around the world. The pirates battle the fierce captains and crews of opponent ships. They encounter the soldier guards and the merciless Executioner in the Spanish castle. In the ninja camp they fight the Ninja Master and his followers. On the beach the heroes encounter the dreaded Medusa and a horde of wicked skeletons that rise from the dead. Finally, the pirates reach the Wizard's Island, where they must again do battle against the shadow figures of the Executioner, the Ninja Master, and the Medusa before they can fight face-to-face with the evil Wizard. If they make it to the throne room and overcome the Wizard, players are rewarded with a room full of treasure. Players use a joystick and sword button in a combination of defensive and offensive maneuvers to battle the various enemies. Players can learn the lunge and backslash, two. skilled sword-fighting moves that are the most effective. . In order to increase the long-term appeal of the -game, players can select various difficulty levels of easy, medium, and hard to vary their paths through the game. By selecting the longer hard path, players are rewarded with more food, drink, and booty along the way. . Game Play Hints Stand over the white crossed bones that mark the spot of buried treasure and press the sword button to dig it up. Walk over the treasure to collect it. In order to get the highest score, first start the digging, then battle the opponents on each screen. Collect all the treasure before moving on to the next scene. The most difficult opponents in each wave (ship captains, Executioner, Ninja Master and Medusa) each protect a special treasure. By destroying these enemies, the players are given the special item that will protect them in the final round on the Wizard's Island. In a two-player game, the two players must duel over these special treasures.
Skull & Crossbones Universal Kit Installation
Ms. Use a copy of this ate for the second o s a = = temp!
1-8
Chapter 2
Self-Test
The Skull & Crossbones™ game tests itself and provides visual and audible indications of the condition of the game circuitry and controls. Self-test information is displayed on the screen and through the sound system. No additional equipment is required. We suggest that you perform the self-test when you first set up the game, each time you collect the money, or when you suspect game failure. The self-test screens provide information about the game circuits and controls. To enter the self-test, turn on the self-test switch located at the front of the JSA Audio II board. To leave the Self-Test, tum off the self-test switch only while displaying the Select Test menu.
Self-Test Skull & Crossbones Universal Kit
Table 2-1 Summary of All Self-Test Screens
Screen Use or Purpose_ Statistics Screen Displays game statistics. # Histogram Screen 1
- Complete RAM Test Screen _* Complete ROM Test Screen ©
- Playfield Test Screen *
Alpha Test Screen
Color Test Screen :
Red Color Purity Screen
Green Color Purity Screen - . Blue Color Purity Screen White Color Purity Screen © - Grey Color Purity Screen oak
White Convergence Screen
Violet Convergence Screen . Green Convergence Screen Displays the histogram for all new games. Displays the histogram for all continued games.
: Displays the histogram for the level at which pl
Use to set and check the coin’ ions séttings. . Use to check the audio PCB circuits, RAM, and.
Use to check the green color purity in th ‘Use to check the blue color purity in the ~_. Use to check the’ white color in the video disy _ Dae to check the grey: color in the video f
Use to check and adjust
Use to check and adjust video display conver; ~ Use to check and adjust video ‘
Self-Test Selection
The 13 tests in the self-test procedure are listed in a menu, which is displayed immediately after you enter the self-test. To select any of the tests, move the left joystick up or down (you can also press the left Turn button). To start the selected test, press the left player sword button. To leave the self-test, turn off the selftest switch when the menu is displayed. The 13 tests are: ® Statistics and Histograms ™@ Game Options Test ® Coin Options @ Playfield Test m@ Motion Object Test m@ Alphanumeric Pfld Test m@ Sound Board Test ™ Color Test @ Switch Test @ Purity Test ™ Complete RAM Test ™ Convergence Test @ Complete ROM Test
2-2 Statistics and Histogram Screens
Use the information shown on the statistics screen and on the histogram screens to keep track of your game use. Record the information on the Skull & Crossbones statistics page in the back of this manual. The information shown on the Statistics Screen (see Figure 2-1) is accumulated from the last time the statistics were reset. Simultaneously press the RED DOG SWORD and TURN buttons to reset the statistics. At the bottom of the statistics screen are two times and dates. These are the program version dates. If you are having problems with your game, you may need to give Atari Games Customer Service this information. The statistics screen shows the following statistics: @™ eft Coins: number of coins deposited into the left coin mechanism. & Right Coins: number of coins deposited into the right coin mechanism. @ New Players: number of players beginning a new game.
Skull & Crossbones Universal Kit
STATISTICS Lett Coins 20 Right Coins
OPlyr Mins 1 Plyr Mins 2 Plyr Mins L Plyr Mins a
Total Coins 1 Plyr Coins 2 Plyr Coins Avg Time'coin Avg i p tim vg 2 p ti RED DOG to si Press ONE-EYE SWORD Button for histograms. 29 SEP 1989 16:53:40 24 OCT 1989 15:4
Figure 2-1 Statistics Screen
™ Bonus coins: number of extra coins that players have accrued before entering the game. § 0 Plyr Minutes: number of minutes of non-use. @ 1 Plyr Minutes: number of minutes of 1-player use. § 2 Plyr Minutes: number of minutes of 2-player use. LZ Plyr Minutes: number of minutes of left-side use. WR Plyr Minutes: number of minutes of right-side use. &@ Sessions: shows the total number of games played since the last time the statistics were cleared. @ Error Count: shows the number of errors counted in the erasable memory. If you have a count of more than 75, you should have your game serviced by a qualified service technician. &§ Total Coins: accumulation of coins from the left and tight coin mechanisms. @ 1 Player Coins: number of coins used in the 1-player mode. ™ 2 Player Coins: number of coins used in the 2-player mode. ™ Average Time per Coin: time divided by the total number of coins deposited. ™ Average 1P Time/coin: 1-player minutes divided by the 1-player coins deposited ™ Average 2P Time/coin: 2-player minutes divided by the 2-player coins deposited Hist The first of the three usable histogram screens is shown in Figure 2-2. The three histogram screens display the following information:
@ Histogram 1 shows the time in seconds of all first coins deposited. Self-Test
Histogram 1 Time for the First Start Hea
90-119 120-149
ONE-EYE SwWo! to return to menu and TURN Button
Figure 2-2 Histogram 1 Screen
™ Histogram 2 shows the time in seconds of all additional coins deposited. @ Histogram 3 shows at which waves the players did not continue. @ Histograms 4, 5, and 6 are for development use only, and contain no operator-adjustable information. If you read the screens infrequently, the number of games will always be correct proportionally, but may be incorrect numerically.
Game Options
To move through the game options, including the ones before the word MORE, push the left joystick stick up or down. You can change the highlighted game option. The factory default settings are shown in green. To change an option setting, move the left joystick right or left.
™ Sounds in Attract (Mode)? plays the Skull & Crossbones game music, if set to yes. ™@ Reset High Score Table? clears the high score table, if set to yes.
2-3
Self-Test
| Game Difficulty? adjusts the speed of the enemies that players must fight during each wave. @ Health at Start? controls the amount of health given at the start of the game. ™ Health for Additional Coins? controls the amount of health given for inserting additional coins. ™ Bonus Health (for) Coins Added Before Start? controls whether you give progressively larger amounts of health to players who insert additional coins before entering the game. ™@ The Low Health Warning? option is a type of censor to eliminate the blood spurt warning to players that their health is about to run out.
GAME OPTIONS
Sounds in Attract? No Reset High Score Tabie? No Game Difficulty? Moderate Health at Start? 50, Health for Additional coins?
Move ONE-EYE JOYSTICK to select options. ONE-EYE TURN Button
Figure 2-3 Game Options Screen
@ Coins Mechs? can allow all the coins to be pooled, and players must then assign the coins to each other by pressing one of the two auxiliary coin switches. Refer to Chapter 1 for more information. @ Restore Factory Default? allows you to set all the game options to the factory-recommended options by choosing yes. If you want to use your own settings, be sure to set this to no. The Game Option Screen can be seen in Figure 2-3 above.
Coin Options
To move through the coin options, push the left joystick up or down. You can change the highlighted coin option. The factory default settings are shown in green. To change an option setting, move the left joystick right or left.
™@ Coins to Start a New Player is the number of coins required for a new player to enter the game. Skull & Crossbones Universal Kit
COIN OPTIONS
Coins to Start a New Player Two Coins Multiplier
INE-EYE JOY: to select options 5 ONE-EYE TURN Button restores original setting WORD Button
Figure 2-4 Coin Options Screen
@ Multiplier is the value of each coin inserted in the coin mechanisms. For example, if you select 2, then each coin counts as two coins. @ Bonus Adder lets you choose bonus coins, no bonus, or free play.
Sound Board Test
The sound test indicates the condition of the music and sound effects circuits on the JSA Audio II Board. The sound test screen is shown in Figure 2-5. The
Current Coin Value : 0000 Number of Sounds 178
Sound CPU Status : Good
to select sound Press ONE-EYE SWORD Button to return to menu
Figure 2-5 Sound Board Test Screen
sound microprocessor resets at the beginning of the test. You will hear the first sound three seconds after the test starts. After the microprocessor is reset and you hear the first sound, the number of the game sounds and the sound CPU status appear information. If the CPU is good, the word “Good” appears. If you get an error message at any point in the sound test, see Table 2-3 for more information. The test cycles through the following tests:
Skull & Crossbones Univers.:! Kit
@ Music Chip Test @ ADPCM Test
m@SCOM Reset Test
Switch Test
The switch test is shown in Figure 2-6. Use this test to check the controls. As you press the buttons and move the joysticks, the proper lines should light up.
SWITCH TEST
Press buttons and move sticks
Left UP Let Down Loft LEFT Right UP Right DOWN Right LEFT Left RIGHT Right RIGHT fi AUX1 ht AUX t UX 2 Right AUX 2 Left TURN Right TURN Lett NEXT SWORD ght NE
Press ONE SWORD and TURN Buttons to return lo menu
Figure 2-6 Switch Test Screen
If the highlighting does not appear, follow the maintenance and repair procedures for the controls in Chapter 3 of this manual. Press the left player SWORD and TURN buttons together to move to the next screen.
Complete RAM Test
While this test is checking the RAMs, you see a white screen. If the game successfully completes the RAM Self-Test
test, the menu will reappear in less than 15 seconds. If the game has a bad RAM, you may see a message (see Figure 2-7 for an example) or, if the problem is severe, you may only see a colored screen.
VIDEO-LEF
Figure 2-7 RAM Error Message
Complete ROM Test
If the game has an error in the program ROMs, then the error number is shown on the ROM test screen within two seconds. The characters in parentheses de-
Table 2-2 Game Option Settings
Health for Add’l Coins Bonus Health for Coins Added Before Start?
Restore Factory Defantt Yes
+ Manufacturer's recommended settings
2-5
Self-Test
ROM BAD -2
Figure 2-8 ROM Error Message
Playfield Test
This test indicates the condition of some of the graphics ROMs, the vertical and horizontal scroll registers, and the joystick control. Use the left joystick to move left, right, up, and down. Press the left TURN button to see all the playfield palettes, numbered 0 to 15. The screen is shown in Figure 2-9. Exit the screen by pressing the left sword button.
Motion Object Test
The motion object test screen is shown in Figure 2-10. This tests the movement and color of various game objects.
Table 2-3 Faulty Sound RAM and ROM Locations Skull & Crossbones Universal Kit
Figure 2-9 Playfield Test Screen
Choose an object with the left sword button. Use the left joystick to move the object. Press the left jump button to move to the next object. Exit the screen by pressing the left SWORD and TURN buttons.
Alphanumeric Pfld Test
The alphanumeric test checks the condition of the alphanumerics in the game. If you see stripes or brokenup characters, then the chip at 250K on the game PCB is probably bad.
The SCOM chip is a CMOS IC and is static-sensitive. If you do not bandle it properly, you can permanently damage this chip.
Communications Error #2 __ TI PCB ig disconnecied from | oe Se is not inserted into: cket.
‘Sound Processor Not 'A major problem with the JSA Audio If PCB. I
Responding check that the connector between the JSA Audio It Pt is plugged in properly. oes
Skull & Crossbones Universal Kit
6 1234867890902 *
Figure 2-11 Alphanumeric Test
Color Test
This test indicates the condition of the video display color circuits. The screen is shown in Figure 2-12. The left side of the screen should be black and change to light colors on the right. From top to bottom the screen should appear white, red, green, and blue. If the screen does not fit this description, refer to the manual for your video display. Exit the screen by pressing left sword button.
Color Purity Test
The color purity test has five screens. The first screen is shown in Figure 2-13. These screens show the condition of the color purity circuit in the video display. Each screen should display a rectangle of color, with no curving at the corners Self-Test
Figure 2-12 Color Test
and no lines in the display. The screens are red, green, blue, white, and gray. If the screens are not correct, see the video display manual included with the game for adjustments. Exit each screen by pressing any left TURN button.
Convergence Test
The convergence test is shown in Figure 2-14. This test has three screens. The first is white, the second is purple, and the last is green. Check the following on the screens: m™ The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel. ™ The convergence of the lines on the violet and white screens should be within 2.0 mm.
Ladie : - 7 ;
tha
Figure 2-14 Convergence Test Figure 2-13 Color Purity Test
Chapter 3
Maintenance and Troubleshooting
This chapter contains regular maintenance information, troubleshooting tables, and repair procedures for your Skull & Crossbones game. This chapter contains the regular preventive maintenance schedule and information on maintaining the joystick. The next part contains three troubleshooting tables. One table has general troubleshooting information, the second contains the voltage levels and test points on the PCBs, and the last is a table of ROM-caused problems with specific ROMs to check and replace. The last past of the chapter contains repair procedures and removal instructions for the joystick, video display, and speakers of the Skull & Crossbones game. If a part is mentioned, but not illustrated, see Chapter 4, Illustrated Parts Lists, for information.
Maintenance
Preventive Maintenance
Preventive maintenance includes inspecting, cleaning, lubricating, and tightening hardware. Perform the preventive maintenance regularly so you can keep the game in top condition, avoid problems, and maximize your earnings. Preventive maintenance tasks and intervals are shown in Table 3-1. For the best performance from your Skull & Crossbones game, you should check and maintain your game according to the times shown in Table 3-1. The preventive maintenance procedures for the joystick and coin mechanism are in this section.
Maintaining the Joystick
Maintain the joystick by inspecting the pivot ball, actuator half-ball, and the shaft and by lubricating the joystick with lithium grease.
- Turn off the power to the game.
- Open the control panel and disconnect the harness connector.
- Remove the joystick from the control panel. Use a 3/8-inch wrench to remove the nuts and washers that hold the joystick on the control panel.
- Remove the four long screws that hold the joystick together. See Figure 3-1.
- Take off the 8-position plate, the actuator, and the lower housing.
- Check the actuator half-ball, the pivot ball, and the shaft for dirt and wear.
- Lubricate the actuator half-ball on the end of the joystick shaft, the pivot ball below the upper housing, and the spring inside the upper housing. Use lithium grease. .
- Put the joystick assembly back together. Fit the pin in the pivot ball into the slot in the lower housing.
Table 3-1 Maintenance and Inspection Items Skull & Crossbones Universal Kit
- Replace the long screws and tighten them. Do not over-tighten the screws. The joystick handle must return to center easily.
- Replace the joystick assembly on the control panel.
- Use the self-test to make sure you have reassembled the joystick correctly. dust and dirt out with. compressed air.
Troubleshooting
The tables in this section (3-2, 3-3, and 3-4) can help you troubleshoot problems in your game. The troubleshooting table lists possible sources of problems of various parts of the game The voltage inputs and test points can help you troubleshoot PCB problems. The ROM problems table can help determine exactly which ROM might be causing game play problems.
Repairs
This section includes the procedure for repairing the joystick assembly.
Disassembling the Joystick
Perform the following procedure to disassemble the joystick (see Figure 3-1).
- Take off the control panel and disconnect the harness connectors.
- Remove the joystick from the control panel. Use a 3/8-inch wrench to remove the four locknuts and washers holding the joystick onto the control panel.
- Remove the four screws holding the 8-position plate on the bottom of the assembly.
- Remove the white plastic actuator and the lower housing that the four switches are attached to.
- Remove the small roll pin holding the actuator half-
Interior Components "Every 3 months Joystick Every 3 months
PushButtons Every 6 months “Lubricate. Make sure nuts holding: ~ control panel are tight. © : f Make sure the pushbuttons are tight on the control panel.
3-2
Skull & Crossbones Universal Kit
ball on the bottom of the shaft by pushing the roll pin all the way through the shaft. Slide the actuator half-ball off the end of the shaft. 6, Remove the large roll pin holding the large pivot ball on the shaft below the upper housing. Push the pin through the ball and the shaft. The pin will not be easy to remove because of the pressure on the pivot ball from the spring above it. After you push the pin all the way through the ball, slide the pivot ball off the shaft.
- Slide the upper housing off the shaft. Slide the plunger and the spring off the shaft.
- Slide the disc off the shaft.
Rearsemibling the Joystick Install the disc on the shaft.
- Slide the spring on the shaft. Push the large end of plunger onto the shaft and over part of the spring (see Figure 3-1).
3, Slide the upper housing onto the shaft.
- Before you put the pivot ball on the shaft, insert the large roll pin partway into the pivot ball. The roll pin should not interfere with sliding the pivot ball onto the shaft. Slide the ball onto the shaft, and line up the roll pin with the hole in the shaft. Now push the pin through the shaft. You will have to hold the pivot ball against the pressure of the spring. Make sure the ends of the roll pin extend out the same amount on both sides.
- Put the small roll pin part way into the actuator ball and slide the ball onto the shaft. Line up the roll pin with the shaft hole. Push the roll pin Maintenance
through the ball and the shaft.
- Fit the lower housing over the shaft so that the ends of the large roll pin fit into the slots on the inside of the housing. Turn the lower housing so that screw casings align with the holes in the upper housing.
- Put on the white plastic actuator so that the black cushion ring is opposite the switches.
- Now install the 8-position plate below the actuator so that you can reinsert the long screws.
- Put the long Phillips head screws through the 8-position plate and up through the housings. Do not over-tighten the screws, or the joystick will be too hard to move.
- Reinstall the joystick on the control panel.
Table 3-2 Voltage Inputs and Test Points on the PCBs
‘Test Point PCB Voltage or LED Source and Purpose Main +5+0.25 VDC. VCC1
Main Ri LED
Audio cR4 LED
Audio CR3 LED Audio CR5 LED
loge power from the swiliching Power supply. is open.
loge power from the swiliching Power supply Lights when the -5 V supply i is hod
Lights when the +5 V supply is good. °
Lights when the +12 V supply is good (but only if the auc 12 V resistor at Q3 on it).
3-3
Maintenance ‘Skull & Crossbones Universal Kit
4 Lithium Grease Ball-Shaped Handle
and Shaft 4
Disc
Plunger Spring
N
N Plunger |__ Upper Housing Ww . Assembly ~N
Upper Housing
Snap Action Switch
Cushion Ring i pono oo nr I a
Pivot Ball 1
“Os Roll Pin
_~ N .086" Dia Roll Pin
8 Position Plate ! ‘Actuator Half-Ball
Figure 3-1 Maintaining the Joystick
3-4
Skull & Crossbones Universal Kit Maintenance
Table 3-3 Troubleshooting Table
Suggested Action Test the coin mechanisms with the sound test screen in the
- Check the ames. and Connectors.
- Perform the self-test. _
3. Check the voltage levels on the PCBs. See
: 4, Check What ROM Problems Look Live, Table
Asscreen character does not Check the connections. move or moves Jenerminentty.
b. Are the video display’s filaments lit?
c. Do you have high wollage to the video display?
(Power voltage is 100 VAC or 110 VAC, de Video signal voltage is 0.5 to 3.5 Vol
Display area wavers or is too small
Convergence, purity ‘Use the screens in the self-test to adjust the video or color problems : ae ay.
Game is stuck in Make sure both self-test switches are switched off. If one or both are switched self-test the game will be in self-test. Ee
Maintenance
Table 3-4 What ROM Problems Look Like Skull & Crossbones Universal Kit
Problem Program works but letters and numbers appear wrong. Program works and the playfield looks OK, but the motion
"Program works, motion objects look OK, but the playfield
is wrong.
~ Game program is erratic.
No sound or erratic sound. ‘Garbage on screen; program doesn’t work.” meas eS Alphanumeric Motion object
Playfield
Chapter 4
Illustrated Parts Lists
This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers, and so on usually are not listed in the parts lists. The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All “A” prefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (000598- through 201000-). Ending the list are part numbers with a twonumber designation followed by a hyphen (00- through 99-). The PCB parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of your kit. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Games Customer Service phone numbers are listed on the inside front cover of this manual.
Figure 4-1 Skull & Crossbones Kit Assembly A047450-01 B
Parts List
| Part No. | Description | Part No. | Description |
| 047052-01 | Left Coin Decal | 177010-240 | —-#10-24 Poly Locknut |
| 047052-01 | _—_-Right Coin Decal | 178237-001 | Red Button Assembly |
047053-01 Side Panel Decal
| 047205-01 | Attraction Shield | 178237-005 | Blue Button Assembly |
178265-001 _L-Style Nylon Standoff 72-6612S #6 x 3/4-Inch-Long, Type AB, Cross-Recessed
| 047209-01 | Control Panel Cover | Screw | |
| 047451-01 | Display Bezel with Graphics | 75-5116B | #10-24 x 1-Inch-Long Black Carriage Bolt |
047452-01 Attraction Film with Graphics
| 047453-01 | Control Panel Decal | A040933-03 | —8-Position Microswitch Joystick |
A046501-01 = JAMMA Harness Assembly
| 047454-01 | Set of Control Functions Labels | A046903-01 | Skull & Crossbones Game PCB Assembly |
| 160044-001 | Snap-Action Microswitch with Gold | A047184-02 | JSA Audio II PCB Assembly |
Contacts
Illustrated Parts Lists Skull & Crossbones Universal Kit
f aeresT-0n o40304-01 Lithium Grease Ball-Shaped Handle and Shatt
03971201 ‘a047010-02 Plunger |_ Upper Housing ‘Assembly
044390-01 Cushion Ring
73-20824 125° Dia Roll Pin
73-2050 039717-03 086" Dia Roll Pin
8-Position Plate 040693-01 = ‘Actuator Half-Ball,
Figure 4-2 Microswitch Joystick Assembly A040933-03 B
4-2
Figure 4-3 Skull & Crossbones Game PCB Assembly A046903-01 F A\ SEE PARTS LIST FOR ACCEPTABLE SUBSTITUTE. NOTES: zi - * 13007e-x108 ome wry
rig C3 F183 Foo us74 Fer For eps 300 JOS s0e 85 sor] 5] son Saar 1 OF aoa 1 F200 cory cot 19759¥-001 FA7Y RTE Faz fase = Lsoy fie eine 2 wr Fare “[aeore~ ee aR te su fu sed, ae mo oth ot? fa aig
ce Oe Fa OP ¢ a Bs oot est Fare iO ants map ag
- ta LS08. s usi75 & rare aaa F2u4 Ls74 oe soz a Seopa fat 197534-001 ee = cae] oho
oe Lses7 Ls7¥. rae I Ds a
is
1s13¢ us37a 49.9483 son] J_isee "Ta an bgt === 197593-002 136072-x152 (me 2 S27 am fe ru —— usar bap nm s]9%) we ne iY Buses usar —— us Ls374
: THOUENIST ores bg sa QH/ PM) exe 0 B us 5 tp 137586-00 137264-003 reo OO, st aa FEET 19¢072-K182 7 Ge") me alea a S x 2 ROWGIOZ-Ot
LsiwA —LsiwA Tasen] ese] Fae] Skull & Crossbones Universal Kit Illustrated Parts Lists
Skull & Crossbones Universal Kit Mlustrated Parts Lists
136072-xx46
136072-XX47 ve
136072-XxX48 n
TDAZ030 we
137607-001
he ry ped un IN Pr)
iJ Io tad 80> > 10 8 Ls393 E sis Ls273 9 a™
mH ey s0i_ 4] 02 7 =;
. ity S138 3 137526-001 Lsi74 40668
Figure 4-4 JSA Audio II PCB Assembly A047184-02 A m0 ob Se gp) SE EE (Bevis Ls24o0 136056-2101
?) sy «P= Oe omg
> Ba toer | gecuet OO
88 Owe a o
wt sP-1
4-4
Chapter 5
Schematic Diagrams
About this Chapter...
This chapter contains the schematics and wiring diagrams for memory map and the faulty your Skull & Crossbones™ game. —_ " . RAM/ROM tables. (The PCB as- These are arranged in the follow- sembly drawings are illustrated in ing order: Skull & Crossbones Game PCB, JSA Audio II Chapter 4, Illustrated Parts Lists.) PCB, the Skull & Crossbones
vw ‘Schematic Diagrams Skull & Crossbones Universal Kit
ALOF 4 ve roa
1006 2s 4— /256H soa 1006
- S$ yiy ‘Lso4 Skull & Crossbones Universal Kit Schematic Diagrams
axl 1-37
SPARE 1/0 PINS
> JAAPR-7 —> JRR-H
- FER 9 > JAAR > reme-25 — > seeme-co > Feme-26— seewn-00
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 1 of 10 046903-01 D
Schematic Diagrams
5-4
Skull & Crossbones Universal Kit
Skull & Crossbones Universal Kit Schematic Diagrams
isa DE 79s— Dot as iste 2006 Az3— fot raza Lsia
4 A1PLE vroRee os nes los /o3 FuLL,| Jieet oe ‘800- Fy ast sm (Ji-2? jRCSREO RIG = 1K a-29. - SELFTEST ces ” JAMA S123 15
14H. ‘Ji-2s
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 2 of 10 046903-01 D
Schematic Diagrams
5-6 Skull & Crossbones Universal Kit
sangenes Skull & Crossbones Universal Kit Schematic Diagrams
ae grt: gaiz
| BH | ms | os |
fans
| nP. | fr: | at | at |
| = | Ex | as | a |
| ay. | At: | Atzoy | a. |
| a | & | azey | |
| Bs. | fais | aril. | |
| = | eato—ielas 8 | AL. | |
| 289. | ga — eine | ea. | |
| BAe. | OLS BRe——Tar | os 8 | on |
| Es | O13 Bees | 33 Se | at |
fas
| /SLAPSTIK | Sas. | ‘otz 8A | laa | ‘oz 8 | Of |
| BAe. | Ort sRa——Zlas | tt Be | ‘OL | ||
| Baa. | O10 8A3—tlne | a 8A3 | Of | ||
| ere. | oy an2— Tie | OF BAR. | OF | ||
| At. | 08 Ai — 2 fao | ‘08 BAL: | 08 |
ert re BAL. At: azn gat: sa2— Baus mie. sar1— fae BALL. BALO- jay BAi0 ea9— lon BAY. BAG. jar or 07 8A. ‘Sar. lolol 06 SA?- Bab—Sles os OS BA BAS. jae 04] Oa BA BAa——Zlas os 03 8 BA3- Az Oe G2 BA: Beets OL BAe. BAi— ee on 00 BAL. eo
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 3 of 10 04690301 D
5-7
‘Schematic Diagrams
a seor
SSPRoes, usesa
FREE H PEEREOGERE
eects f pees are 8 rigs Fh seus le jen tes an. ce Lado
ie cm reuse wees Te, evs title: A Te a wrt, qe 5 = ics
ASB RASA he vrpee14—ttics: © URAMAL3. at SH VRAMAL2. as SS vaamari—S fate vane 0— ia vRaRI—Sn8 vasens—Ler vo1s,
| RAR? | —lA6 | vOL4 |
| RA | 08 | v033, |
| ORs | Ine | O32 |
| vesena—Z | ea | voiL |
vreens—tre void
| vRrmne—T | ea, | voy |
| renal | Eee | vos |
1a ‘Skull & Crossbones Universal Kit
aK rr
S8R85858 RRARSEGREEIE ERAS seRsears (F)
iss
UREMALE URARALL URARELO
URARAT ‘Skull & Crossbones Universal Kit
1805 BARSLORCRIEREDA anne
B8R58R58
@aooouce 4.8374 SRESSGR9 Sa588858 Schematic Diagrams
Seoee 2010
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 4 of 10 04690301 D
5-9
Schematic Diagrams Sinill & Crosstones/Universab Kit ‘Skull & Crossbones Universal Kit ‘Schematic Diagrams
voe—lo ale sor
| al, | @ SO oe PFPALS | é |
vos ito Fare orPatg 4 & app arpa, vor—Ho 3 ape 2
| van | io foc PFPALL | 4 |
| ra | vo13. | 0 |
| aps | prpaca | a |
o vote. yaea.sx— vot.
| Fs | [ae | oxo. |
130K 2605 vors—tfo eine Faery: vors—Ho | a—prptcis P86 voLe—Ho | te —erpieia Bias « Hie pele vos—s1o & aes—aretce
| vO10- | fo 4 al | PFPICLO |
vOLi—#lo ~ att prpicis sa se a ANPIXO lc 401 bilse
ato!
Prercss. PRPICI PrPice. Prercs. PrPIC?. Prete mie Fi PrPIC3 i Her ort prots preter Preici—les esti orats PFPICO: PFPICO—Sine oe} 48 —PrOiz avs. 4s—tjes oa} prot ie fea ater HeLrsthe: HeurstHe— 2 }00 oof — pros fee Jez
| prpicas. | prptcis | erereni ttf ] | |
| Prercio. | PrPrcio. | prpicio— | fas |
| PrPice. | PrPTCy. | eae | |
| PrP Ica. | PrPICB | Les tans | |
| Pretcr, | preic? | Be | Eine] |
Teen lator fee iene elas ort pro7 Lisl ae
| 6 Pr OS | tar | PFO? |
| oP pros | a | PFO |
| Ob Pros | yes | PFOS |
| ost PrOS | fsa | Laat |
eH prog acaba
| mE pros | az | PFO2 | |
| on] | PFOO | fa | PFOL |
| g | Cy | PFOO |
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 5 of 10 046903-01 D
5-10 5-11
m " Crossbones Unit it Schematic(Diagrams Skull & elUniveral ke Skull & Crossbones Universal Kit Schematic Diagrams
ens
iy — 10037 003% oe tH—n0033 rs M0032 M0031 pd — 10030
or} mo027 oat rane 4 MO02 4 os HET ro023 cet ooze os He nooas 00} 0020,
OROMAL4—} Fats ieee MOROMAL3 Faas
| ¢ | ats | teroati—t Hae, |
az :
| a poeRtS | prey | Fonornio Eas g |
RLM MOROMAI— Eh Aan.
| OPAL 3 | ees | roe ae |
| Sopa | ae | ronan’ 1 lee |
| OPALO | tar or} tron? | oRoMAe—t Har or} Ht —-moo17 |
jae octet mooie §=—HOROMAS]—F}me vel EL MOOS 4 aS OS mOo1S ‘MOROMAS- res Shi 001s [3a ttine 06 MOO4 = MOROMA——$4ne capt OLS = trina oat} —mon13 = MOR yaa caf 31-0013 cre St roo | Moncey tee ret rool
| ca | Tislee Soft mooie | oot moo 8 |
| co | e | 9 |
| z | S | % |
| roams St saer | reset | Syme |
ifmas fas
| tere: | Fae | peas | pororai ji ate |
| YRAERZ | Le aa3 | moromai2—t#etaaa |
bt Hatzes MOROMALI 2 atzey
| “er | Hes | per anes |
Listas moronns—tttlar S
| moROMR: | rs | ronora Sine | Lay |
Liar nononme—ttlar or} Ht -mop07 T$96 ronomns—t tla sf Ht M0006 cos MORONS Ostet MODS ary moRoHAI—t-S4ne «PT —n0004 wmarey wororme tas ost} na003 ee monoMAi Tyee oe tt no002 bat moromma tla: ot} tt} nooo.
| 48 | foal | ne 00 | M000 0 |
roromen7 je be = tsi
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 6 of 10 046903-01 D
5-12 5-13
Schematic Diagrams
5-14 RSRa2RE PRooees ry
:
BRE THe 430n SEREERES BEEN
‘MOROMAL 4: MOROMAL 3: MOROMALZ! rey MOROMALL! Atzoa ty : z REPRESS gi sereeaes 4:
MORCHAL 4: ass MOROMAL 3: ase MOROMAL?: ass MOROMALL Piey MOROMALD: asin & aso a a ‘ar a6 ne a3 fae ms ry $3: ‘Skull & Crossbones Universal Kit Skull & Crossbones Universal Kit s the Dig
seroeaes BERELAST
eee Hae 450N 0027 002 6 ! M0025 M0024 90023 MOOSE moot M0026 SERQPRRS B2RSIRSS dg d2REPaRaE
x OO 6 M0014 0043 M0082 O04 M0010
430N B2RELERLE RERELRRA aes aeeaeede Sri d
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 7of 10 04690301 D
5-15
Schematic Diagrams Skull & Crossbones Universal Kit Skull & Crossbones Universal Kit Schematic Diagrams
i 3 30K stirue—2)_ > . re, va 123t <4 4 md 5
reer o moo17—Z}o Petts o, ss 0036-202 ae — Len monz6—ts}0 3 a ft— ngoen moprs—o aE 7BEN
Mig Sm AHFLIPD:
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 8 of 10 046903-01 D
5-16 5-17
Schematic Diagrams Skull & Crossbones Universal Kit Skull & Crossbones Universal Kit Schematic Diagrams
Y
R80 RS7 SR79 R90 SRE 1K ak fax IK Fun A A i MOP 1x4.
me ftiles ex: ij 3SN, eon ea 4 tB0R ries as Bons. 1 [ro bd ima aH my oa}
40H a 7080 (er)
40H rr $— nos.
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 9 of 10 046903-01 D
5-18 5-19
Schematic Diagrams
5-20 q z i 8 Le 2 oh fata a9 2Kxes|
a
jae Tre Skull & Crossbones Universal Kit
408,
we7a
Ato.s74 los ah SEaESESS us245, seszeees Skull & Crossbones Universal Kit
Capon — Hot vrocux a 32
Figure 5-1 Skull & Crossbones Game PCB Assembly Schematic Diagram, Sheet 10 of 10 04690301 D
‘Schematic Diagrams
5-21
Schematic Diagrams
C2,8,4,22,23, 30,47 ,63-67 a
COYPASS) ‘Skull & Crossbones Universal Kit
ct i Re3 Skull & Crossbones Universal Kit
2-15, Schematic Diagrams
Figure 5-2 Skull & Crossbones JSA Audio II PCB Assembly Schematic Diagram, Sheet 1 of 3 046487-01 D
5-23 ns
schematic Diagrams Skull & Crossbones Universal Kit skull & Crossbones Universal Kit
eR 8 88
e502A BG BAS
SRERBSARRS
1L93K ‘Schematic Diagrams
8ia% §
Figure 5-2 Skull & Crossbones JSA Audio Il PCB Assembly Schematic Diagram,
5-24 Sheet 2 of 3
5-25
Schematic Diagrams Skull & Crossbones Universal Kit skull & Crossbones Universal Kit ‘Schematic Diagrams
Figure 5-2 Skull & Crossbones JSA Audio II PCB Assembly Schematic Diagram, Sheet 3 of 3 046487-01 D
5-26 5-27
5-28 ‘Skull & Crossbones Universal Kit
SKULL & CROSSBONES MEMORY MAP
DATA ' wocceccreecnannnn | AMAR t comma { 2222 1211 1111 11AA AAAA AAAA | R/| 1111 11D DDD DoDD | oxcriow EEODECDOL | 3240 9876 5432 1098 7654 3210 | W | 5432 1098 7654 3210 |
000000-O7FFFF =| OXXX XAAA AAAA AARA AAAA AAAA | R | DDDD DDDD DDDD DDDD | 512K BYTES PROGRAM ROM 038000-O3FFFF | OXXX 4011 1AAA AAAA AAAA AAAA | R | DDDD DDDD DDDD DDDD | 32K BYTES SLAPSTIC PROGRAM ROM SPACE
| FFOCOO | 1 AXKX XXXX 0000 11XX XXXX XXXX | WI | | UNLOCK EEROM |
| FF1401 | | UXXX XXxX 0001 O1XX XXXX XXXI | WI | DDD DDD | AUDIO WRITE |
| FF1800 | 1 1XXX XXKX 0001 1OXX XXXX XXXX [WI | | AUDIO RESET |
| FFIF80 | 1 UXKK XXXX 0002 1121 1XXX XKKK | WL | | WATCHDOG |
| FF1FOO | | AXXK XXXX 0001 1112 OXKX XKXX | W | | | VIDEO IRQ ACKNOWLEDGE |
FF2000-FF2FFE | 1XXX XXXX 001X AAAA AAAA AAAO |R/WI XDDD DDDD DDDD DDDD | COLOR RAM
| FF4801 | | LXXX XXXX 0100 1XXX XXXX XXX 1 RJ | DDDD DDD | AUDIO READ |
| FF5800 | | 1200 XxXxx 0101 1xxx XXXX XKOO | R 1 DDDD DDD | | INPUTS ~ PLAYER 1 |
R popp LEFT PLAYER JOYSTICK (U, D, L, R) D LEFT AUX #1 (DEVELOPMENT ONLY) D LEFT AUX #2 (DEVELOPMENT ONLY) D LEFT TURN D LEFT SWORD
| FF5802 | FUNK XXXX 0101 1XXX XKXX XXOO | R | DDDD DODD | | INPUTS - PLAYER 2 |
R ppop RIGHT PLAYER JOYSTICK (U, D, L, R) D RIGHT AUX #1 (DEVELOPMENT ONLY) > RIGHT AUX #2 (DEVELOPMENT ONLY) RIGHT TORN D RIGHT SWORD
| FF5803 | LU AXXX XXXX 0101 1XXX XXXX XX1L 1 -R | | ppp | | staros. |
| | UXXX XXXX 0201 1XXxX OK XKIL | R | | D | | SELF-TEST | |
| 1 AXKX XXXX 0102 1XXX XXXX XX11 1 R | | D | | AUDIO BUSY FLAG | |
| 1 LXKK XOKX 0101 1XXK XXKX KIL ER | | D | | VBLANK | |
| 1 AXXX XXXX 0101 1XKK XXKX XXI1 | R | | D | | HBLANK | |
| FR6001-FF6FFF | | 1XXX XXXX 011X AAAA AAAA AAAL [R/W] | DDDD DODD | EEROM |
FF@000-FFBFFE = |_1XXX XXXX 100A AAAA AAAA AAAO |R/W| DDDD DDDD DDDD DDDD | SCROLLING PLAYFIELD RAM FFCOQO-FFCEFE =| XXX XXXX 1100 AAAA AAAA AAAO IR/W| DODD DDDD DDDD DDDD | ALPHANUMERICS RAM FFDOOO-FFDFFE =| 1XXX XXXX 1101 1AAA AAAA AAAO |R/W! DDDD DDD DDDD DDDD | MOTION OBJECT RAM FFEQOO-FFFFFF =| 1XXX XXXX 111A AAAA AAAA AAAA |R/W! DDDD DDDD DDDD DDDD | PROGRAM RAM skull & Crossbones Universal Kit
Video RAM bad
Color RAM bad
Table 2 ROM Error Locations Schematic Diagrams
Figure 5-3 Skull & Crossbones Faulty RAM/ROM Tables & Memory Map
5-29
Schematic Diagrams Skull & Crossbones Universal Kit
N O T E S
5-30
Skull & Crossbones” Statistics Sheet
Statistics Screen:
Left (Mechanism) Coins Right (Mechanism) Coins New Players Bonus Coins
0-Player Minutes 1-Player Minutes 2-Player Minutes Left-Player Minutes Right-Player Minutes Sessions
Error Count
Total Coins
1-Player Coins 2-Player Coins Average Time/Coin Average 1-Player Time/Coin Average 2-Player Time/Coin
5-31
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for is low. ADDRESS ‘A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off), Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton, switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a micro- Processor). BINARY A number system that expresses all values by using two digits ( and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER
- An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP . An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that irispects the coin to determine if the correct coin has been inserted.
COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry.
Glossary
COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device frocessing. DARLINGTON A two-transistor amplifier that provides extremely high gain.
DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage.
gl-1
FLYBACK A step-up transformer used in a display to provide the high voltage. GATE
- A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
- A circuit in which one signal switches another signal on and off.
- To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used.
IMPLODE To burst inward; the inward collapse of a vacuum tube. Vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. IED The abbreviation for a light-emitting diode.
LOCKOUT COIL Directs coins into the coin return box when there is no power to the game.
LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER
- A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
- An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located.
TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. ‘WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If
a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or cfedit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller’s plant; and (©) Seller’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
J G
Atari Games Corporation
675 Sycamore Drive
P.O. Box 361110
Milpitas, CA 95035 fa